The Earth's Core
This is Volume 37 in INTERNATIONAL GEOPHYSICS SERIES A series of monographs and textbooks Edited by WILLIAM L. D O N N A complete list of the books in this series appears at the end of this volume.
The Earth's Core
J . A. JACOBS Department of Earth Sciences University of Cambridge. England
SECOND EDITION
1987
ACADEMIC PRESS San Diego
New York
Harcourt Brace Jovanovich, Publishers London Orlando Austin Boston Sydney Tokyo Toronto
ACADEMIC PRESS INC. (LONDON) LTD 24/28 Oval Road, London N W I 7DX
W'
United States Edition published by ACADEMIC PRESS INC. Orlando, Florida 32887
Copyright @ 1987 by ACADEMIC PRESS INC. (LONDON) LTD All rights reserved. No part of this book may be reproduced in any form by photostat, microfilm, or any other means, without written permission from the publishers
British Library Cataloguing in Publication Data
Jacobs, J. A. The earth's core.-2nd ed.(International geophysics series, ISSN 0074-6142; v. 37). 1. Earth-Core I. Title II. Series 551 .I '1 2 QE509 ISBN 0 - 1 2-378951 - 6
Filrnset by Eta Services (Typesetters) Ltd, Beccles, Suffolk and printed in Great Britain by St Edrnundsbury Press Ltd, Bury St Edmunds, Suffolk
Preface t o the First Edition
The innermost regions of the Earth are inaccessible to man and no direct measurements of any of its physical properties can be made. Much attention has been given in the last few years to the “inverse problem in geophysicsthat of determining some physical parameter from a set of observations made at the surface of the Earth. Our knowledge of the core of the Earth comes from many different fields, of which seismology and geomagnetism are the most important and a discussion of these disciplines form a large part of this book. The role of the Earth’s core is essential to our understanding of many geophysical phenomena-it is the seat of the Earth’s magnetic field and coupling between the core and mantle is responsible for some of the variations in the length of the day. The advent of satellites and spacecraft to the moon and terrestrial planets has given an added interest to the internal properties of these bodies-measurements of their magnetic field has already given us some clues on their constitution and possible cores. The question of cores in the other planets is discussed in the last chapter. J. A. JACOBS J u l y 1975 ”
V
This page intentionally left blank
Preface t o the Second Edition
It is just over ten years since the first edition of The Earth‘s Core was published It has been said that the typical doubling period for the accumulation of scientific knowledge during the last two centuries is about fifteen years, and this is certainly the case for the Earth’s core. The second edition has been largely rewritten and expanded, but follows the same layout as the first edition. The first chapter on the general physical properties of the Earth now includes a long section on the core-mantle boundary (the so-called D” layer). The section on free oscillations of the Earth is extended and a section on attenuation (the Q of the Earth) added. In Chapter 2, the accretion mechanism is treated in much more detail and the sections on heat sources in the early Earth and the time of core formation more thoroughly discussed. Chapter 3 now contains a section on Griineisen’s parameter and its role in the thermal regime of the Earth. Melting-point depth curves are discussed in more detail in the light of more recent highpressure shock wave data and a new section is added on the thermal consequences of an iron-alloy core. In Chapter 4 the section on reversals of the Earth’s magnetic field is greatly expanded and the sections on the energetics of the Earth’s core and on variations in the length of the day largely rewritten. A new section on the secular variation is added. Chapter 5 has been considerably modified. I t now contains a more detailed discussion of equations of state and a new section on experimental methods (both static and dynamic). The constitution of the Earth’s core is reviewed in more detail and the case for the presence of silicon, sulphur, oxygen and potassium in the core assessed. Chapter 6 is essentially rewritten. It contains much more information on the cores of the Moon and vii
viii
Preface to the Second Edition
other planets-mainly as a result of increased data from space probes and more detailed numerical modelling. In general SI units have been used. However, in some cases where the older system seems to persist in much of the literature, their usage has been retained, e.g. densities are expressed in g/cm3 rather than in kg/m3. This also has the advantage that their magnitude is reduced by a factor of three. Again the ST unit of pressure is the pascal (Pa), but much experimental work at high pressures still quotes results in kilobars (kb). The conversion is 1 giga pascal (GPa) = 10 k bar. Pressures in the Earth’s core exceed 100 G P a = 1 M bar. J. A. JACOBS
Contents
Preface to the First Edition Preface to the Second Edition
Chapter O n e
V
vii
General Physical Properties of t h e Earth
I. I I .2 1.3 I .4
Introduction Travel-Time and Velocity-Depth Curves The Core-Mantle Boundary (MCB) Free Oscillations of the Earth 1.5 Attenuation in the Earth 1.6 Variation of Density and Other Physical Properties within the Earth 1.7 Models of the Earth’s Interior
Chapter Two 2.1 2.2 2.3 2.4 2.5 2.6
3. I 3.2 3.3 3.4 3.5 3.6 3.7 3.8
30 39 48 56
The Origin of t h e Core
Introduction The Accretion Mechanism Heat Sources for an Earth Accreting Cold Time of Core Formation Inhomogeneous Models of the Earth Variation of the Gravitational Constant G with Time
Chapter Three
i
3 18
81
82 93 107 116 126
The Thermal Regime of t h e Earth’s Core
Introduction Gruneisen’s Parameter The Earths Inner Core Melting-Point-Depth Curves Adiabatic Temperatures The Earth’s Inner Core Reconsidered Thermal Consequences of an Iron-Alloy Core The Core and the Thermal History of the Earth ix
137 137 145 147 159 164 169 175
Contents
X
Chapter Four 4. I 4.2 4.3 4.4 4.5 4.6 4.7 4.8
The Earth’s Magnetic Field
Introduction The Origin of the Earth’s Magnetic Field The Homogeneous Dynamo Equations Mean-Field Electrodynamics Reversals of the Earth’s Magnetic Field Energetics of the Earth’s Core The Secular Variation Variations in the Length of the Day
191 20 I 207 213 217 236 247 267
Chapter Five The Constitution of t h e Core 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8
Equations of State The Birch--Murnaghan Equation of State Experimental Methods Ramsey’s Hypothesis Bullen’s (k,p ) Hypothesis Bullen’s Fe,O Hypothesis The Constitution of the Core The Possibility of Potassium in the Core
Chapter Six 6.1 6.2 6.3 6.4 6.5 6.6 6.7
The Cores of Other Planets
Introduction Mercury Mars Venus TheMoon Summary The Great Planets
Appendix A Index
291 299 302 308 310 314 315 336
347 349 359 371 377 39 1 394
407 409
Chapter One
Genera I Phys ica I Properties of the Earth
1.1 Introduction
This book is concerned with the Earth’s core-the innermost regions of the Earth. No direct measurements can be made of any of its physical properties and in some ways we know more about the distant stars than we do about the deep interior of the Earth. However, the core plays a key role in many geophysical studies-amongst other things it is believed that the Earth’s magnetic field is a result of motions in the fluid outer core ($4.2). The core, whose radius is just over one-half of that of the Earth, consists of an outer core (OC) that is fluid and an inner core (IC) that is most probably solid-there may also be one or more transition zones between these two regions. The radius of the IC is about one-fifth that of the Earth-thus, although its linear dimensions are quite large, its volume is only about 0.007 that of the whole Earth. Geophysics is an observational science and our objective is to try to explain our observations with theories based on sound scientific principles. To do this we set up models that approximate conditions in the real Earth and try to solve the problem for this idealized situation. A whole series of models of ever-increasing sophistication can be considered, but it must not be forgotten that they are only models and that the real Earth may behave quite differently. The assumptions and limitations of any model must be clearly stated and always borne in mind when assessing the success of any theory. 1
2
The Earth‘s Core
The mathematical equations that describe most physical phenomena are often non-linear and extremely complex so that analytical solutions are in general not possible. In many cases order-of-magnitude arguments are used to draw some preliminary conclusions, but one must be very wary of much of this type of “arithmetic”, since it is all too easy to be misled by “geophysical numerology” (Jacobs, 1970). In such cases intuition is a notoriously bad guide. Moreover, order-of-magnitude calculations can often lead to contradictions resulting from over simplification of the original equations. Our knowledge of the deep interior of the Earth is pieced together from information obtained from a number of different disciplines-physics, chemistry, astronomy and geology. A fundamental problem in geophysics is the determination of some physical parameter (e.g. density) from a set of observations made at the surface of the Earth. This “inverse” problem as it is called has received much attention during the last few years. It has been formulated using sophisticated mathematics, and with the aid of modern computers it is also possible to obtain information about the uncertainty and non-uniqueness of Earth models. The resulting proliferation of Earth models has had two consequences. Firstly, there is the difficulty of choice of an adequate Earth model for researches that depend on the structure of the Earth; and secondly, several researchers have adopted some properties from one model and other properties from another, with the result that their models are not self-consistent. At the XV General Assembly of the International Union of Geodesy and Geophysics (IUGG), held in Moscow in 1971, a committee was set up to advise on a Standard Earth Model (SEM) covering the distribution of various physical properties of the Earth’s interior. A necessary requirement of a reference Earth model is that it must fit data on the Earth’s mean radius R, mass M , and z where I = z M R 2 and I is the Earth’s mean moment of inertia. Account must be taken of data derived from records of seismic body waves, seismic surface waves, and free Earth oscillations. In addition there is a large body of information from other sources, including data on Earth tides, finitestrain and solid-state theory, laboratory experiments on rocks (including shock-wave experiments at pressures up to 4 million atmospheres), and evidence from other disciplines such as planetary physics, geology and geochemistry. The SEM committee set up a number of subcommittees to examine particular aspects of the SEM project. At a meeting of the Symposium on Mathematical Geophysics held at Banff in 1972, three research groups, headed by D. L. Anderson, F. Gilbert and F. Press, presented Earth models giving the main parameters. The results were published in the Geophysical Journal 35, 1973. At a meeting of the International Association of Seismology and Physics of the Earth’s Interior (IASPEI) in Lima in 1973, there was agree-
General Physical Properties of the Earth
3
ment about the need for a parameterization of an Earth model and Dziewonski et al. (1975) later published parametrically simple Earth models (PEM) consistent with geophysical data. It was also decided in Lima to publish some of the interim reports prepared by the sub-committees (Physics of the Earth & Planetary Interiors 9, 1 4 4 , 1974). By the time of the IASPEI meeting in Durham in 1977 it had become evident that it was possible to construct Earth models taking account of damping. The effects of attenuation were considered to be important, but since such effects are not well-determined it was decided to produce two Earth models-one including attenuation and one not. It was further decided to entrust to D. L. Anderson and A. M. Dziewonski the task of constructing suitable models. They presented a Preliminary Reference Earth Model (PREM) at the XVII General Assembly of the IUGG in Canberra in 1979 that was subsequently published in Physics of the Earth & Planetary Interiors 25,297-356,1981. Although a definitive SEM has not yet been produced, the SEM committee was finally dissolved at the XVIII General Assembly of the IUGG in Hamburg in 1983. It was realized, however, that refinement of the Preliminary Reference Earth Model is necessary, and further work is continuing, Details of recent Earth models are given in $1.7.
1.2 Travel-Time and Velocity-Depth Curves
The major source of our information about the Earth’s interior comes from the field of seismology. Following an earthquake, elastic waves travel throughout the Earth and may be observed at the large number of seismological stations distributed across the world. The theory of the propagation of elastic waves may be found in any standard text on seismology (see, for example, Bullen, 1963) and will not be developed here. There are two distinct types of elastic waves-P waves and S waves. A P wave is a condensation- . rarefaction wave involving change of volume. Motion of the medium is longitudinal, so that there is no polarization of a P wave. An S wave is a shear wave in which there is distortion without change of volume. S waves are transverse waves and thus exhibit polarization. In addition surface waves are set up: these have yielded valuable information about the crustal layers of the Earth. Recently, long-period surface waves have been used to obtain additional information about the deeper parts of the Earth. It can be shown that the velocities of P and S waves are given by
4
The Earths Core
and r
V, =
J’P
where k, is the bulk modulus or adiabatic incompressibility, ,u the modulus of rigidity and p the density. Thus V p and V, depend only on the elastic parameters and density of the medium. In particular, if the rigidity is zero, V, = 0, i.e. shear waves cannot be transmitted through a liquid. It follows from (1.1) and (1.2) that r#~ =
k,/p = V;
-
$Vg
(1.3)
When an elastic wave meets a sharp boundary between two media of different properties, part of it will be reflected and part refracted, and laws of reflection and refraction analogous to those of geometrical optics apply. The case of elastic waves is more complicated, however, since waves of both P and S type may be reflected and refracted. The‘ theory is based on Fermat’s principle, according to which an elastic wave takes the quickest path between any two points. This does not imply that there is only one path-there may be a number of alternative paths-but each path must involve a minimum transit time relative to small deviations in the path. Figure 1.1 illustrates some of the many possible reflections and refractions of elastic waves at discontinuities within the Earth. The figure also illustrates the terminology used to designate some of the different phases. A P wave reflected from the Earth’s surface can give rise to both a P wave and an S wave (called PP and PS waves respectively). Likewise an S wave reflected from the surface can give both P and S waves (called SP and SS waves respectively). The letters c and i denote reflections from the boundaries of the OC and IC respectively, and h denotes reflection from the surface of the F shell (the transition layer between the OC and IC). The letters Kand I are used for P waves in the O C and IC. Thus SKP is an S wave that has been refracted into the OC (necessarily as a P wave) and refracted back into the mantle as a P wave. S waves have never been observed in the OC, which is thus considered to be liquid. On the other hand, it has often been conjectured that the IC is solid and the symbol J was proposed for paths of S waves (if they exist) in the IC. It was not until 1972 that Julian et al. claimed to have identified the phase P K J K P on seismograms4onfirmation of their work would establish the existence of rigidity in the IC directly. They obtained a value of V, N 2.95 km s - ’ in the IC which is difficult to reconcile with that of -3.6 km s - ’ obtained by Gilbert et al. (1973) from an analysis of free Earth oscillation data (see $1.4). A value of -3.6 km s- also follows from Bullen’s ( k , p ) hypothesis (see 55.5). There is a possibility that Julian et al. observed the phase (1974) has suggested that the SKJKP, rather than PKJKP-Doornbos
’
5
General Physical Properties of the Earth
----s rays Fig. 1 .l.Representative seismic rays through the Earth (After Bullen, 1954.)
phase P K J K P is too small to be observed. Multiple ( n ) internal refections from the mantle-core boundary (MCB) into the O C are indicated by nK. Thus P7KP is a P wave that has been refracted into the OC, suffering 7 internal reflections in the core before being refracted back into the mantle as a P wave (see Fig. 1.2). The times of arrival of the different seismic waves may be determined from the records at a number of stations, so that it is possible to construct traveltime curves, i.e. plots of arrival times T against distance A (measured in degrees along the surface of the Earth) between the source and the seismic observatory. The construction of travel-time curves has had a long history of successive approximation and increasing accuracy. Revision of the early travel-time curves was undertaken by Jeffreys in 1931 (see Jeffreys, 1936, 1961 for complete details) using a least-squares technique. In collaboration with Bullen he produced the first J.B. Tables in 1935. Substantial refinements were incorporated in a new set of J.B. Tables first published in 1940. These gave travel-times, not only of P and S waves, but also of reflected and refracted
6
The Earths Core
Fig. 1.2. Diagram showing seven internal reflections from the M C B into the OC (P7KP). (After C. H . Chapman.)
waves. Details of the production of these tables and of the early history of the subject may be found in Bullen (1963). Improvements in the records and the use of large artificial explosions have led to corrections to the J.B. Tables (see e.g. Herrin, 1968). However, the production of the J.B. Tables, before highspeed computers were avilable, was a monumental achievement. From the travel-time curves, it is possible to calculate the velocities of P and S waves at any depth within the Earth. The details of such an inversion will not be given here (see e.g. Bullen (1963) for details). Figure 1.3 shows the gross features of the velocity-depth curves in the Earth according to Jeffreys and Gutenberg. During 1940-42, Bullen divided the Earth into a number of regions based on such curves. His nomenclature
7
General Physical Properties of the Earth
Depth ( k m ) Fig. 1.3. Seismic velocities of P and S waves as a function of depth. (After Birch, 1952.)
has since been widely used, and, in spite of uncertainties in the positions (and realities) of the boundaries between the different regions, continues to serve as a useful basis in discussing the Earth’s interior. The upper mantle consists of region B extending from the base of the crust (region A) to a depth of about 400 km, and region C which is a transition zone between depths of about 400 and 1000 km. The lower mantle, below a depth of about 1000km, is called region D. The core is divided into an outer core E, a transition region F and an inner core G. In recent years much finer detail has been obtained, particularly in the upper mantle (regions B and C, see Fig. 1.4), and in the vicinity of the boundary of the IC (region F). In the following discussion of the physical properties of the Earth, attention will be confined to the core and very deep mantle: no account will be given of the crust or the low-velocity layer in the upper mantle, nor of possible phase changes in region C. Sengupta and Julian (1978) have investigated the variation of P and S wave velocities in the lower mantle using data from deep-focus earthquakes. The chief advantage of using deep-focus earthquakes is the reduction of anomalies caused by complex structures near the source. Their standard deviations of average travel times are as much as a factor of two smaller than those determined from the data of shallow-focus earthquakes (see e.g., Herrin et al., 1968; Hales and Roberts, 1970). No pronounced decrease in either the P or S
8
The Earth's Core
Pressure ( k bar )
I. I. I
I' 1.
I:p I:
1:
I:
I: I: I'
i
c IL
I' 6.
LOWER
MANTLE
:?
CORE
L
t
;z .........../*'
..'
......
1: I:..
I I
fNIA1; MOHO. I I
i
I
I
Depth ( k m 1 Fig. 1.4. Seismic velocity distribution in the mantle for P waves, solid line (Johnson, 1967, 1969); S waves, solid line (Nuttli, 1969); broken lines P and S waves (Jeffreys, 1937, 1 9 3 9 ~ ) (After . Ringwood, 1972.)
velocity just above the MCB is required by their data, though a small velocity decrease could not be ruled out (see also $1.3). However, anomalous rapid changes in the gradient of the P velocity were found around depths of 2400 km and 2600 km. Their model for P velocities in the lower mantle agrees best with that of Herrin et al. (1968), and for S velocities with the 1066B model of Gilbert and Dziewonski (1975). Lee and Johnson (1984a) used travel-time data from the ISC Bulletin to
9
General Physical Properties of the Earth
0
1000 Y v
f a cu
a 2000
3000
4
6
a
10 Velocity ( k m s-')
12
14
Fig. 1.5. P a n d S velocitydepth bounds computed with upper mantle 7 ( p ) envelope. (After Lee and
Johnson, 1984a.)
determine confidence limits for the seismic parameter z(p) = T ( p ) - pA(p) where p is the ray parameter for mantle P and S waves. One year of P data (- 108,000 travel-times) and four years of S data (- 75,000 travel-times) were used. Based on these results, they obtained (Lee and Johnson, 1984b) extrema1 bounds on seismic velocities in the mantle (see Fig. 1.5). Bounds on the lower mantle P velocity have an average resolution of 70 km in the depth range -800-2900 km. The average bound width is -0.14 km sC1 at the 97% confidence level. Bounds on the lower mantle S velocity have an average resolution of 85 km in the depth range -850-2900 km and an average width of 0.13 km s-l. These confidence limits were computed with an assumed upper mantle velocity distribution. It should be noted that linearized inverse techniques (e.g. Backus and Gilbert, 1970; Johnson and Gilbert, 1972a,b) provide uncertainties in velocity and depth at a particular point in a model, whereas the method of Lee and Johnson establishes a confidence region for the entire model. The inversion methods of obtaining velocity-depth curves from travel-time curves break down if there is a region in the Earth in which the velocity decreases with depth. In such a case there will be a range of A in which arrivals from an earthquake are not observed (a shadow zone). There is an abrupt, discontinuous drop in the velocity of P waves across the MCB with a corresponding shadow zone in the range 105" < A < 143". Some waves are recorded in this range, however, so that it is not a true shadow zone (see Fig. 1.6).The
10
The Earths Core
Fig. 1.6. P, PcP, PKP, PKIKP, and diffracted P waves. (After Bullen, 1954)
amplitudes of such waves are much reduced and for many years their presence was attributed to diffraction round the boundary of the core. Miss I. Lehmann suggested in 1936 that such waves had passed through an IC in which the P wave velocity is significantly greater than that in the O C and later work has corroborated her hypothesis. Our present knowledge of seismic velocities in the core comes chiefly from the interpretation of travel-times of short-period P waves. There is a wide variation in the estimated velocities of P waves just below the MCB with likely values ranging from 7.9 k m s - ' (Hales and Roberts, 1971) to 8.26 k m s - l (Randall, 1970). Inversion studies favour a value fairly close to Jeffreys'( 1939d) value of 8.10 km s-'. At depths in the O C greater than about 200 km, most velocity models converge to values that are generally higher than those of the Jeffreys (1939d) model, although within 0.1 km s-' of it. A detailed discussion of the results of different authors has been given by Engdahl(1968). Nearly all authors of travel-time studies agree that there is a gradual increase in P velocity in the O C down to a depth of about 4600 km. Most disagreements arise in the transition zone F between the OC and IC. Calculations by Gutenberg and Richter (1938, 1939) and by Jeffreys (1939c,d) corroborated Miss Lehmann's hypothesis of a rapid or discontinuous increase in the velocity of P waves in the Earth's core, but differed in the interpretation of the velocity distribution near the inner core boundary (ICB). Jeffreys assumed that the wave velocity decreased with depth just above the IC, and then increased discontinuously at the ICB (see Fig. 1.3). Gutenberg, on the other hand, favoured a gradual increase in velocity in a transition zone without a preceding decrease. Neither of these models, however, can explain (using ray theory alone) the observed short-period precursors to P K P waves at distances less than 140". Jeffreys (1939~)considered
General Physical Properties of the Earth
11
diffraction near a caustic and showed that appreciable amplitudes for a diffracted P K P wave could not exist more than about 3" from the P K P caustic at 143" for periods of 1 s, or 14" for periods of 10 s. Denson (1952) and Gutenberg (1957, 1958a,b, 1959) attributed these early arrivals to dispersion in the transition zone. The lack of definitive observational evidence, however, is a significant argument against accepting this as the mechanism that is operative in the Earth. An explanation for the early onsets in terms of magnetoelastic coupling was also shown to be unlikely by Knopoff and Macdonald (1958). Bolt (1962,1964) proposed that two discontinuous increases in the velocity distribution of P waves in the Earth's core could explain these arrivals as rays refracted through an intermediate shell. He used observations from a study of P K P readings in the range 11O0
12
The Earths Core
11 I I I I
I
.-
h
m
E lo
Y u
L > _V
-ar0
Jeffreys (1939 a , b )
-Bolt (1962) .......... Adams-Randall (1964) Randall (1971) .-.-.- Hales -Rober t s (1 971 )
>
9
0
#-
1
0 0 0
-
Model KOR5
-
I
8 1 3000
I 2000
I
I
1000
0
Radius ( k m ) Fig. 1.7. Compressional wave velocity for different core models. (After Qamar. 1973.)
recorded deep-focus earthquakes and a near-surface event. Arrival times and amplitudes of core phases from these events were supplemented by P K P observations. Engdahl first tried to find a solution in terms of a decreasing velocity function within the intermediate shell of the Bolt core model-his velocity distribution is shown in Fig. 1.8 (the Bolt core model is indicated by the dashed line). He obtained an alternative velocity model (Fig. 1.9) by increasing the radius of the Bolt intermediate layer to a point just below the radius of penetration (r,, = 1881 km) of the point B (the P K P caustic). These two models represent the limits of allowable velocity solutions for a singlelayer transition zone corresponding to the observed data. Engdahl (1968) also considered more complicated models with additional discontinuities in the core. The velocity function proposed by Adams and Randall (1964) consisted of three discontinuous increases between the OC and IC-the details of this velocity structure are shown by the dashed line in Fig. 1.7 Engdahl came to the conclusion that the unusual curvatures indicated between 0.3 and 0.6 Rc are artificial and unwarranted by the data.
14
-
13
1
I
1
1
1
I
1
L
I
-
L
c
ul
E
-
12-
Y
v
.-=U. 0 s0
L
.-C u
11
9
-
I I
-
10-
9-
L 3
.-
0 C
o
-1
8-
7.
1
1
1
I
I
I
1
I
I
1
Fig. 1.8. Compressional wave velocity in the core. The dashed line represents the Bolt core model. (After Engdahl. 1968.)
14
I
I
I
I
1
I
1
I
I
13
-
-
El2
-
-
h
c
ul Y
v
r/ Rc Fig.1.9. Alternative compressional wave velocity in the core. The dashed line represents the Bolt core model. (After Engdahl, 1968.)
14
The Earth's Core
7
I
I
1
1
1.0
I
1
I
1
0.8
1
I
1
1
0.6 r/ Rc
1
I
1
1
0.4
I
1
1
I
0.2
I
I 0
Fig. 1.10. Compressional wave velocity in the core The dashed line represents the Adams-Randall model (After Engdahl. 1968 )
To test the hypothesis of multiple discontinuities in the core, Engdahl set up a model consisting of two constant-velocity shells within the transition zone (Fig. 1.10). To be consistent with observational data for models of this type, it was necessary to consider changes in the core which prevent rays in the OC from forming a P K P caustic at B (the P K K P caustic is preserved). Engdahl thus believes that the fine structure of the core proposed by Adams and Randall has not been established. Engdahl concluded that a working model of the core consisting of a singlelayer transition zone (a modified Bolt model) can explain the observed data within reasonably close limits. This layer is between 400 and 600 km thick and has a P velocity distribution either constant or decreasing with depth. In order to explain early P K P arrivals, characteristically observed in the range 125"-140", a velocity discontinuity must be introduced in the core between radii of 1667 and 1806 km, approximately. The radius of this discontinuity defines the top of the transition layer. The bottom of the layer or ICB, also defined by a jump in the velocity, is between radii of about 1233 and 1250 km. Haddon (1972), in a study of precursors to PKZKP, concluded that they were not likely to be associated with the presence of a transition layer of the Bolt type, nor with any internal discontinuities inside the OC or IC, and suggested that they may be caused by scattering of P K P waves from irregularities near the MCB. In addition to meeting the observational requirements,
General Physical Properties of the Earth
15
this interpretation has the further advantage of simplicity-the only discontinuity in the core being the boundary between the IC and OC. This is also a feature of model B1 of Jordan (1972)-see $1.7. It must be pointed out, however, that some authors still claim that the seismic data demand a two-layer transition zone in the core, although not excluding inhomogeneities at the base of the mantle that they consider a secondary effect-see, for example, Bertrand and Clowes' (1 974) analysis of travel-times and travel-time gradients recorded at the Warramunga seismic array. These authors claim that the data are best fitted by three discontinuous increases in the P velocity, one at the ICB and two at shallower depths. These discontinuities define two layers, each a few hundred km thick, surrounding the IC-the velocity increase in both of these two layers being less than 0.1 km s - '. Muller (1975) has shown that long-period precursors to PKZKP should be observed if they are due to discontinuities in the OC. However, long-period seismograms* for an earthquake in the New Hebrides do not show them. Muller thus concludes that the discontinuities of Bertrand and Clowes' model are not real and that the P velocity depth-function in the OC in smooth down to the ICB. For most models, P velocities in the IC are approximately constant, the velocity increase at the ICB being 0.9-1.0 km s- '. The models of Buchbinder (1971) and Qamar (1973) are exceptions-they show a velocity increase of about 0.6 km s-' at the ICB followed by a pronounced velocity gradient in the outermost part of the IC. Qamar's model (KOR5) is also shown in Fig. 1.7-it was developed to satisfy all available observations of travel-times, dT/dA, and amplitudes of core waves. The model is also tied to the Herrin (1968) tables for P and the Randall (1970) tables for S K S . The average velocity in the transition region is 1)% lower than in Bolt's (1962) model: at the outer boundary of the transition zone ( r = 1782 km), model KOR5 has a velocity jump of only 0.013 km s-l, which is 1/20 of that in Bolt's (1962) model. The jump at the ICB (I = 1213 km) is 0.6 km s-', which is about 2/3 of that in most other models. Very similar results have been obtained by Muller (1973) from a study of long-period core phases. He found that the P velocity distribution is quite smooth right down to the ICB with no first-order discontinuities in the transition region. The P velocity increase at the ICB is 0.60.7 km s-', with again a strong velocity gradient in the outer part of the IC; the S velocity just inside the boundary of the IC is -3.5 km s-'. This is greater than the value of 2.95 km s - ' obtained by Julian et al. (1972) in their paper claiming to have identified the phase P K J K P and confirms the value obtained earlier by Dziewonski and Gilbert (1971) based on normal mode oscillations (see 91.4). The simplest explanation of a possible velocity gradient or a constant * From the
World- Wide Standardized Seismograph Network ( W W S S N ) .
16
The Earth’s Core
velocity in the F region is the existence of an abnormally high temperature there, which would imply radioactive heat sources in the core. Liu (1982a) has shown by geochemical arguments that there should be about one-third to one-half of the Earth’s heat-producing elements below the upper mantle. O’Nions et al. (1978) and Clark and Turekian (1979) came to the same conclusion to account for the heat flux observed at the Earth’s surface. Highpressure experiments by Liu (1 982b) showed that these heat-producing elements would exist as dioxide solid solutions that are chemically incompatible with the major mantle silicates at the temperature and pressure conditions in the lower mantle. Because of the great densities of these dioxides, probably in excess of that of the liquid OC, Liu (1982a) suggested that they may be gravitationally transported to, and concentrated in, the F zone. Alder and Trigueros (1977) explained the small observed dependence with pressure of the speed of sound just outside the solid IC by suggesting that there is a eutectic region between the liquid O C and solid IC.* If the composition lies on the liquidus of a eutectic phase diagram, the liquid phase would be in equilibrium with pure solid iron, which precipitates out. Along the liquidus the concentration of the lighter component would increase as complete solidification is approached. Since the lighter component will in general have a lower sound speed, increasing its concentration would result in a mixture whose sound speed may be nearly constant, since the effect of the pressure increase is nearly compensated for by the concentration increase. Alder and Trigueros calculated the change in concentration of the light element required to give the observed variation of sound speed with depth and estimated the resulting variation of density with depth. They found that the change in concentration is comparable to that for the known liquidus under normal conditions if the light component is sulphur or silicon. They also found that the predicted density change along the liquidus is very small, possibly leading to hydrodynamic instabilities. Their suggestion remains an interesting possibility, but it is difficult to quantify the results because of uncertainty in predicting the sound speed of iron alloyed with different elements at the pressure and temperature conditions of the core. Seismic anelasticity studies (see $1.5) indicate anomalously low Q t for P waves in the core, which suggests that the outer part of the IC may be
* See 55.7: It is generally believed that the OC consists of Fe alloyed with some 10% lighter element. t Departures from ideal elasticity in the Earth can be expressed in terms of the reciprocal of the dimensionless parameter Q (Knopoff, 1964), defined by the equation 2nIQ
=
AE/E
where AE is the energy dissipated per cycle and E is the peak energy stored. The mechanical Q defined above is mathematically equivalent to the Q of an oscillatory electrical circuit. A region with low Q values thus implies an extremely dissipative zone.
General Physical Properties of the Earth
17
partially molten. Fearn et al. (198 1) followed up this idea and suggested that the outer part of the IC is a mushy layer of mixed liquid and solid. They found that this layer can be very thick, extending possibly to the centre of the Earth. Although the mechanism proposed by Fearn et al. is in accord with the observational evidence of seismic anelasticity, the agreement is not well-founded, since the anelastic model in common use, in which the anelasticity has been modelled using Landau damping, is inadequate to describe a partially molten system in which melting and freezing can occur. The Landau model works well for a homogeneous material but can lead to serious errors when applied to a heterogeneous material. Loper & Fearn (1983) have since developed a theory of the anelasticity of a partially molten material resulting from thermal and material diffusion (in the Landau model, the governing equations are relaxational rather than diffusive). In their model the OC contains no solid material, but the IC contains liquid in a dendrite layer or mushy zone. This agrees with seismic evidence (Doornbos, 1974; Cormier, 1981; Choy and Cormier, 1983; Hage, 1981) that indicates a non-homogeneous region several hundred kilometres thick below the ICB. The ICB also presents a sharp interface for the phases P K i K P and PKZZKP at small A (Bolt, 1977). The theory of Fearn et al. (1981) is consistent with these observations provided the mass fraction of solid below the ICB grows from zero at the boundary to a significant fraction within several kilometres. Hage (1983) used long-period P K P amplitudes to obtain velocity constraints in the IC. Using theoretical amplitudes (derived from synthetic seismograms calculated for 56 systematic modifications in the IC of Earth model 1066B), he showed that the parameters of a regression line through the logarithmic and normalized amplitudes in the distance range 110-134" are related to the velocity and density jump at the ICB. His analysis showed that the main influence on P K P amplitudes is the jump in the P velocity, which can be restricted to 0.64 0.05 km s- ', implying a need for substantial revision of the P velocity distribution in the IC for core models such as 1066B or PREM. Hage also showed that there is a trade-off between the jump in S velocity and the density jump. Restricting the latter to the reasonable range 0-1.2 g ~ m - he ~ found , the jump in the S velocity at the ICB to be between 2.5 and 3.0 km s-'. The data do not permit a shear velocity less than 2.5 km s - l at the ICB, in contrast to the results of Choy & Cormier (1983), who compared observed with theoretical short-period and broad-band P K P waveforms and suggested that the S velocity may be nearly zero at the top of the IC. Hage also found a rather steep S velocity gradient below the ICB if the travel-time of S waves through the IC is in accord with that implied by free oscillation data. As a result, Poisson's ratio in the IC decreases rather sharply from 0.46 to 0.435. This supports the idea of a dendritic layer characterized by a liquid fraction of core material at the top of the IC as suggested by Fearn et
18
The Earths Core
al. (1981). A decrease in the liquid fraction with depth in the IC would lead to an increase in the S velocity. The analysis of Choy and Cormier (1983) gave a jump of 0.52 0.07 km s - in the P velocity at the ICB in reasonable agreement with that obtained by Hage. They found no zone of small or negative P velocity gradient or of strong anelasticity at the bottom of the OC (the F region). On the other hand, in order to satisfy average properties of the IC inferred from travel-times and normal-mode data, strong gradients in both P and S velocities and anelasticity are required in the upper 20&300 km of the IC. Choy and Cormier concluded that the process of IC solidification produces the most evident seismic effects in body waves with turning points that bottom in the upper 20&300 km of the IC, rather than in the lowermost F region of the OC. This model is not very different from that proposed by Hage (1 983).
1.3 The Core-Mantle Boundary (MCB)
There has been much argument about the structure of the Earth at the base of the mantle (called by Bullen region D"). Apart from its seismological interest, it is critical for thermodynamic models of the mantle. The basic question is whether this boundary layer is compositional and/or thermal. If heat from the core contributes significantly to the convective heat flux of the mantle, then a thermal boundary layer must exist at the base of the mantle so that heat from the core can diffuse across the MCB into the mantle. Models for D" can be divided into two classes-those that allow for an abrupt change in the velocity gradient at the top of D" followed by a nearly constant gradient down to the MCB and those that, in addition to the change in gradient at the top of D", have a more complicated velocity distribution within D". It should be pointed out that even if the seismic velocities in D" are determined to be anomalously low, consistent with a superadiabatic temperature gradient, it cannot be definitely concluded that there is a thermal boundary layer at the MCB-a compositional change would be a possible alternative. However, a thermal boundary layer would seem to be necessary as well, since a significant heat flux from the core is implied by any geodynamo mechanism (see $4.6). The physical mechanisms of the attenuation of seismic waves have been discussed by Jackson and Anderson (1970). Seismic wave attenuation is strongly temperature-dependent, showing a rapid increase with rising temperature. Attenuation increases sharply with the onset of melting-shear waves cannot propagate in a completely molten material. Although the O C is generally considered to be fluid, some investigators believe that it has a finite, though small, rigidity (Sato and Espinosa, 1967; Balakina and Vvedenskaya,
General Physical Properties of the Earth
19
1962). Ibrahim (1971) obtained a better fit to the observed amplitude ratio PcPIP if the O C has a finite rigidity. In a later investigation (1973) he showed that it is easier to explain the observational data (mainly from deep-focus earthquakes) if two to four low-velocity, high-density layers are imbedded between the mantle and core. All Ibrahim’s models indicate that the OC has a finite rigidity, with an upper bound for the shear wave velocity of 1.4 km s-’. Buchbinder and Poupinet (1 973) have criticized Ibrahim’s results and claim that the layered system he proposed is not likely to be found from the data he used (short-period phases sampled at their maximum amplitude), even if such a layered system existed. Buchbinder and Poupinet maintain that PcPIP amplitude ratios cannot be used to study the structure of the MCB. However, from a study of their waveforms (following two large nuclear explosions), they suggest that the MCB may be approximated by a thin highimpedance liquid layer several kilometres thick embedded between the mantle and the core-the data do not permit exact determination of the model parameters, and the structure of the MCB may be radially asymmetric. The shear velocities in the Earth’s lower mantle have long been thought to increase moderately and monotonically downward to the MCB. However, some shear velocity models have been proposed in which the region just above the MCB contains a significant negative velocity gradient. Such models have been proposed by Cleary (19691, Bolt et al. (1970) and Robinson and Kovach (1972) on the basis of dT/dA determinations of diffracted S waves. Their estimates of the shear velocity just above the core range between 6.81 and 6.99 km s - l , as opposed to Jeffreys’ value of 7.30 km s-’. Observations of the periods of free oscillations of the Earth provide additional data for determining the shear velocity distribution (see 41.4). Tradeoffs, however, occur between the shear velocity, density, and core radius, and a unique determination of these is difficult (Dziewonski, 1970). Different investigators have been able to satisfy the free-oscillation data with models differing radically in lower mantle structure. The effect of these trade-offs can be reduced if overtones of the spheroidal and toroidal modes are incorporated in the inversion. Jordan (1972) combined all available free-oscillation data with a large body of travel-times and found that, although a model with a negative shear velocity gradient in the lower 100 km of the mantle provided a satisfactory fit to the data, the fit was not as good as that in which the negative velocity gradient was absent. In model UTD124A’ of Dziewonski and Gilbert (1972) and model B1 of Jordan and Anderson (1974) the P and S velocities vary smoothly down to the MCB without any extreme change in gradient. Both models are in good agreement with most travel-time and free-oscillation data. Their validity rests on the supposition, supported in part by theoretical studies, that data that suggest the presence of a low velocity in D” result from distortion of seismic
20
The Earths Core
waves by the MCB. On the other hand, slowness and amplitude data from short-period P waves indicate a fairly rapid decrease in velocity gradient at a depth corresponding to an epicentral distance of about 92", and it is very unlikely that these data can be interpreted as interface phenomena. The measured P and S times at distances beyond about 96" also indicate reduced velocities in D". In model B2 of Jordan (1972), Bolt's (1972) model, and model ANU2 (Cleary, 1974), the velocity gradients decrease fairly abruptly at a height of 100 km above the MCB and maintain a value close to the critical gradient down to the boundary. All models have high density gradients indicative of inhomogeneity in the region. Model B2 fits the oscillation data reasonably well, but has an unjustifiably low S velocity at the MCB. Mitchell and Helmberger (1973) examined details of the velocity distribution near the base of the mantle that are not resolvable using free-oscillation data or travel-times of reflected waves. Their data consisted of long-period S and ScS waves recorded by the WWSSN and the Seismological Service of Canada. They compared amplitude ratios of these phases with the ratios determined from synthetic seismograms generated by the Cagniard-deHoop method for a spherically layered Earth (Gilbert and Helmberger, 1972). They found that the observed amplitude ratios of transversely polarized shear waves ScSHISH exhibited a minimum at a distance of about 68". Synthetic seismograms computed for a Jeffreys-Bullen model and for models with negative linear velocity gradients at the base of the mantle fail to explain this feature. On the other hand, various positive linear velocity gradients above the MCB can explain the amplitude ratio minimum as well as an apparent difference in arrival times of the transversely and radially polarized core reflections ScS. Good agreement between the observed amplitude ratios and those computed cannot, however, be achieved without assigning low Q values to the lower mantle or a small shear velocity to the OC. High-velocity regions between 40 and 70 km thick containing increases of from 0.3 to 0.5 km s - ' above the velocity of a Jeffreys velocity model yield the best explanation to the combined amplitude and differential time data. Mitchell and Helmberger also observed ScS phases that bottom at widely diverse points on the MCB. They concluded that it is likely that a high-velocity zone is widely prevalent at the base of the mantle and may even be a general feature of that region. Lateral variations in this layer could easily account for the scatter in dT/dA measurements at large distances. Such a model is consistent with the proposed core evolution of Anderson and Hanks (1972) (see $2.5) in which silicate material rich in calcium, aluminium and uranium and having high velocities might remain as a residue from the early processes of core formation. The model derived by Mitchell and Helmberger contrasts sharply with diffusion models, in which it is thought that liquid core material has pene-
-
General Physical Properties of the Earth
21
trated great distances into the lower mantle. If such a phenomenon does occur, it must be restricted to a thin layer that remains undetected by the methods they applied. Wright (1973) analysed d T / d A measurements for P and pP phases for 57 earthquakes at distances between 82” and 115” recorded at the Yellowknife array, and found good evidence for regional differences in lower mantle structure that persist to depths greater than 2700 km. There is also a decrease in velocity with increasing depth below 2825 km. Hales and Maki-Lopez (1980) have carried out an analysis of P wave travel times from the Nevada test site using data from 23 explosions between 1966 and 1976. Their results show a scatter they find difficult to account for in terms of anomalies in the upper mantle near the stations. They suggested that at least some part of the scatter arises in the lower mantle as proposed by Dziewonski et al. (1977). Bolt et al. (1970) studied S wave velocities in D” from diffracted S H waves at the MCB for a north-south North American profile from the Iranian earthquake of August 31, 1968. Okal and Geller (1979) criticized their analysis, maintaining that the measurements were affected by the focal mechanism. Bolt and Niazi (1984) showed that the criticisms are unjustified both theoretically and also by comparison with analogous recordings from the Imperial Valley earthquake of October 15, 1979. They also showed that an S H ray parameter estimated from sharp onsets of diffracted S H waves does not represent a shear velocity averaged over a hundred kilometre depth, but rather the velocity within a few tens of kilometres of the MCB. Bolt and Niazi also analysed long-period seismograms for two Tonga earthquakes and obtained new estimates for the SH slowness, i.e. dT/dA variations, indicating no significant average change in S H velocity at the base of the mantle along two easterly profiles 3000km apart under the east Pacific and North America. The average velocity near the MCB is 7.24 km s-’-in agreement with estimates in D” by Mula and Miiller (1980). This latest analysis by Bolt and Niazi indicates a slightly positive SH velocity gradient towards the base of the mantle, but gives no direct information on the gradient just above the boundary. Haddon (1972), in a study of precursors to P K Z K P , suggested that they may be caused by scattering of P K P waves from irregularities near the MCB. In a later paper, Cleary and Haddon (1972) examined this suggestion in more detail and presented additional evidence in its favour. King et al. (1973) obtained measurements of slowness, within P K Z K P precursor wavetrains which they claim provide crucial evidence in favour of scattering near the MCB. The obvious lack of scatter in the higher-order P n K P arrivals observed by a number of authors suggests that lateral inhomogeneities in the lower mantle are the likely source of scattered waves rather than “bumps” on the MCB. Further support to the suggestion that precursors to PKZKP are
22
The Earth’sCore
the result of the scattering of P K P waves by random irregularities near the base of the mantle has been obtained by King et al. (1974) from an analysis of 12 large earthquakes in the distance range 128”-142” from the Warramunga seismic array in northern Australia. In a later, more detailed analysis, Haddon and Cleary (1974) showed that scattering of P K P waves by random irregularities in densities and elastic parameters of about 1% in the bottom 200 km of the mantle is consistent with most of the evidence on precursors to PKZKP including travel-times, slownesses, azimuthal deviations, amplitudes and amplitude variations. Doornbos (1976) investigated lower mantle inhomogeneities from an analysis of precursors observed at NORSAR. He found localized scattering throughout the region extending to at least 600 km above the MCB. The length-scale of his “window” to the lower mantle was restricted to the range 1&30 km. Smaller or larger-scale inhomogeneities are of course possible. Doornbos showed that convection alone cannot account for the anomalies he found and suggested that they may be due either to rigidity or to density anomalies. If the anomalies are in rigidity only, variations of at least 35% are required, implying that partial melting is almost certainly necessary. If the anomalies are in density only, variations of at least 8% are required, implying chemical inhomogeneities. Later Doornbos (1978) investigated whether bumps on the MCB could be the cause of precursors of certain types of core phases rather than inhomogeneities in the lower mantle. He showed that most of the P K P precursors could be accounted for by both a slightly rough MCB (radial variations up to a few hundred metres) and by a slightly heterogeneous lower mantle (relative variations in physical parameters up to a few per cent). The relevant length-scales of the variations are about the same in both mechanisms (1@20 km). Husebye et al. (1976) re-examined the question of the cause of precursors to the core phase P K I K P , also using data from the NORSAR array. Their analysis confirms the earlier suggestion by Haddon (1972) that they arise from the scattering of ordinary P K P waves by small-scale random irregularities on or near the MCB. Since then considerable support for the scattering hypothesis has been received as against other interpretations that require the presence of transition layers between the IC and OC. Muller (1975) showed that discontinuous variations of more than 0.03 km s-’ within the OC would entail observable long-period precursors, which have never been reported. The analysis of Husebye et al. (1976) also shows that the precursor data of Bertrand and Clowes (1974) are fully consistent with the scattering interpretation and do not require the presence of two discontinuous velocity increases in the OC. In almost all studies of wave velocities and densities on both sides of the MCB using amplitudes of PCP, short-period records from earthquakes and
General Physical Properties of the Earth
23
nuclear explosions have been used. Muller et al. (1977) looked at the amplitudes of long-period PcP waves from two South American deep-focus earthquakes recorded by WWNSS and CSN stations in North America in the hope of reducing the scatter in the PcP/P amplitude ratio characteristic of short-period investigations. They found that most of the models derived from short-period observations and characterized by discrete layers above the MCB are inconsistent with the long-period data. The long-period data also do not permit low, non-zero S velocities below the MCB. On the other hand, simple first-order discontinuity models of the MCB, such as the JeffreysBullen model and models based mainly on free-oscillation data, fit the data resonably well. The agreement of observation and theory is improved for negative P velocity gradients above the MCB. However, a good model for the amplitudes of PcP requires so strong negative gradients that it is no longer a good solution for travel-times of PcP. Sacks et a1. (1979) investigated lateral heterogeneity in the velocity structure near the base of the mantle by analysing amplitude ratios of P K P phases. The observed amplitude ratios vary by well over an order of magnitude, but the size of the ratios is correlated with particular regions of the MCB. Sacks et al. interpreted the differences as indicating lateral heterogeneities in the velocity near the MCB. Clark and Pearce (1981) criticized the analysis of Sacks et al., maintaining that the spread in amplitude ratios is attributable to source radiation patterns as well as focusing and de-focusing by the lowermost mantle velocity structure. Sacks and Snoke (1981) agree with Clark and Pearce that source effects contribute to the scatter of the data, but maintain that their conclusion about variable transmission at the base of the mantle is valid. Doornbos and Mondt (1979a) investigated the attenuation of P and S waves diffracted round the core. A comparison of the observed decay spectra of diffracted P and S H waves with theoretical results for a standard Earth model showed characteristic differences. Both the absolute value and the shape of the observed decay spectra differ significantly for P and SH, whereas the theoretical curves for the standard model do not. Moreover, observational and theoretical curves differ significantly for S H at all frequencies and for P at high frequencies. To explain these differences, Doornbos and Mondt considered five possibilities-velocity gradients in the mantle, density and velocity contrasts across the MCB, anelastic damping, scattering by a rough MCB, and scattering by heterogeneity in the mantle above the MCB. In estimating the importance of various model parameters, they used independent information to put constraints on the model. For some parameters the constraints were sufficient to preclude the associated attenuations as an explanation of the observed anomalies. This was the case with the scattering effects of a rough MCB and of irregular structure above it. Other model parameters
24
The Earths Core
where admissible changes have no significant effect on the decay spectra are the density contrast p + / p - and the P velocities V i , V i , at the MCB (the f signs refer to conditions above and below the MCB respectively). Significant effects were obtained by changing the velocity gradients above the MCB, the velocities V:, V,- at the MCB (a finite V,- implies finite core rigidity), and the anelastic damping factor Q. Characteristics of the observed decay spectra are best explained by models with little anelastic damping of P and SH waves, except possibly for the higher frequencies of S H . This precludes a thick low-Q zone at the base of the mantle, although it would be possible for such a low-Q zone to have a significant effect on the higher frequencies of S. In a companion paper, Doornbos and Mondt (1979b) examined P and S waves diffracted around the core and interpreted the data in terms of a transition zone with a linear velocity profile above the MCB. The combined P and S H data sets allow a thickness of the transition zone of 5&100 km with both P and S velocities decreasing with depth (see Table 1.1). Their preferred model has a thickness of 75km with both P and S velocity gradients -0.0019. There is also a suggestion of an additional low-Q zone at the base of the mantle. The physical implications of such a model are an anomalous density gradient and/or a super-adiabatic temperature gradient above the MCB. The total density increase across a 75 km-thick transition layer would be 3%. This could be explained by diffusion of iron-it would inhibit convection in the region. A super-adiabatic gradient of -9" km-' would be needed to explain the model if the transition layer is assumed to be homogeneous.* Doornbos and Mondt caution that their numerical estimates with regard to density and temperature should be regarded only as rough estimates since the seismic parameters are very sensitive to small changes in the model and values of the thermodynamic parameters are not known very precisely. The early papers on seismic waves scattered on or near the MCB were all related to observations of forward-scattering, where the scattering occurred at entry to, or exit from, the core; from the observations it is not clear whether the scattering occurred at the MCB or in the heterogeneous lower mantle. Chang and Cleary (1978) used P K K P data from Novaya Zemlya explosions recorded at LASA and showed that the back-scattering probably exists also in the form of PK(KP). Since back-scattering does not occur in the lower mantle but at or near the point of underside reflection at the MCB, these data give strong support to the idea that seismic wave scattering occurs on the MCB. In a later paper Chang and Cleary (1981) analysed the same data and
-
-
* Jones (1977) suggested that long-term variations in the frequency of reversals of the Earth's magnetic field may reflect the response of the core to fluctuating temperatures at the MCB. He estimated a temperature gradient of 12"km- across D (see 54.5). Zharkov et al. (1985) made a similar suggestion.
-
TABLE 1 .I Velocity models of the lower mantle for the PEMC madel (Dziewonski et a/. 1975) together with five different perturbations for the base of the mantle (PEMC-LO1,. . ., PEMC-105). (After Doornbosand Mondt 1979b.).
PEM-C
PEMC-LO1
PEMC - LO3
PEMC-LO2
Radius (km) ~
3700 361 0 7 3585 7 3560 7 3485 7
VP
vs
(km/s) -13524 13612 13636 13661 13732
VP
vs
(km 1s)
7169 7200 7209 7218 7243
PEMC- LO5
PEMC-LO4 -
..____.
V.7
VP
(km/s)
VP
vs
13524
7169
13.524
7.169
13661 1 3 519
7218 7076
13.661 13.617
7.218 7 076
VP
vs ( k mIs 1
(km/s) 13.524
7.169
13.636
7.209
13.609
7.067
VP
vs
(km/s)
13.524 13.612
7.169 7.200
13 606
7.060
13.524
7.169
13.661 13.557
7.218 7.130
26
The Earth’s Core
concluded that the observations also require lateral variations in the topography of the MCB and a region of relatively large topography responsible for the anomalous P K K P signals. Doornbos (1980) analysed data of precursors to P K K P observed at NORSAR from several source regions. Following the suggestion of Chang and Cleary (1978) that such signals may be due to back scattering at the MCB, he found that his data implied a rough MCB-with small-scale radial variations of 100-200m, although in some regions the MCB appears to be much smoother. Chang and Cleary (1978,1981) in their analysis of the LASA data suggested that much larger topography may exist in the region of the MCB they sampled. Doornbos pointed out that even small undulations of the MCB may be significant. For finite viscosity q of the mantle, such undulations would tend to be smoothed out. Taking q 10” poise (Cathles, 1975) leads to a decay time of lo5 years, which is small compared with the age of the core. Thus if this estimate of q is correct, the undulations at the MCB must be dynamically produced. Mula (1981) carried out a frequency and time-domain analysis of longperiod P and S waves diffracted round the core observed at WWNSS and CSN stations in order to confirm earlier conclusions (Mula and Muller, 1980) about velocities at the bottom of the mantle that were based on ray parameters. Combining the results from these two investigations, Mula found that models for the base of the mantle with either strongly negative or strongly positive gradients are not acceptable. The only model that satisfied all the data is one with a slightly positive gradient; a slightly negative gradient is possible but unlikely. Mula thus reaffirmed the earlier conclusion that velocities at the base of the mantle increase slowly with depth, implying that there is no significant departure from adiabatic or homogeneous conditions. Thus non-adiabatic gradients, as demanded by a thermal boundary layer as suggested by some authors (e.g. Jones, 1977; Jeanloz and Richter, 1979), are not supported by Mula’s studies. In addition, an extremely-low-Q zone at the base of the mantle is not indicated, Qp being at least greater than 250. Ruff and Helmberger (1982) used the amplitudes of short-period P and diffracted P waves to investigate the internal structure of D”. They used data from Soviet underground nuclear explosions recorded at North American WWSSN stations and synthetic seismograms to test various Earth models and showed that the amplitudes from smooth D” models with a small velocity gradient in D” decay too slowly in the shadow zone. This cannot be explained by random forward-scattering or by a thin low-Q layer within D”. All the features of the observed amplitude profile can be explained as interference effects of a model that has a low-velocity zone in the upper part of D” and a normal velocity gradient in the lower part of D”. The favoured models imply a compositional change and/or a phase change at the top of D” and do
-
-
General Physical Properties of the Earth
27
not allow D" to be interpreted as a single thermal boundary layer between the mantle and core. Ruff and Helmberger suggest that the low-velocity channel could be a double thermal boundary layer with very thin boundary layers if there is sufficient heat flux from the core. However, the existence of a thermal boundary layer at the top of D" does not remove the necessity for compositional stratification. Doornbos (1983) used new long- and short-period diffraction data from the SRO network and from NORSAR in an attempt to settle the question of whether there is a boundary layer at the base of the mantle. Figure 1.1 1 shows three velocity models and two different interpretations of the combined P and S velocity profiles; as a density effect and as a temperature effect. The density profiles assume an adiabatic but possibly chemically inhomogeneous medium, and the temperature profiles assume a chemically homogeneous medium but possibly non-adiabatic conditions. Doornbos concluded from his analysis that the data could best be explained by a relatively thin (< 100 km) low-velocity zone at the base of the mantle, consistent with a thermal boundary layer. Some individual short-period P wave studies from geographically limited regions cannot be explained by this model unless lateral variations also exist. Lateral variations are, however, not in conflict with boundary layer models. Lay and Helmberger (1983a,b) carried out a detailed study of SH phases that traverse the lower mantle. The data show a consistent S H arrival not predicted by smoothly varying gross Earth models. A lower mantle S wave triplication was also found in the distance range 70"-95". Modelling of the observations with synthetic seismograms indicated that the triplication is caused by a roughly 2.75% increase in the shear velocity about 280 km above the MCB. There also appear to be lateral variations in the depth of such a discontinuity of some 4G50 km on a global scale. Lay and Helmberger concluded that the interpretation of the D" region as a thermal boundary layer with diminished velocity gradients caused by a super-adiabatic thermal gradient is inadequate to explain the data, and proposed a new model for the depth dependence of the S wave velocity in the lowermost 400-500 km of the mantle. The main feature of their model is a velocity increase of 2.5-3% across a narrow zone 25G300 km above the MCB, i.e. approximately at the top of the D" layer. Their model predicts pronounced pulse-form changes of longperiod S H body waves in the epicentral distance range 95"-120", a range not studied by them. Schlittenhardt et al. (1985) examined nine long-period seismograms of S H and P waves from deep-focus earthquakes below Fiji, West Brazil, the Sea of Japan, the Sea of Okhotsk and the Banda Sea, and found practically no indication of the predicted changes. They thus rejected Lay and Helmberger's model and suggested that the changes in pulse form that Lay and Helmberger observed at distances from 70°-800, and inter-
28
The Earth's Core
-
I
1
13.7{
L1
PREM
/
13.5
A
I
4000 -
I
3800
3700
3600
3500
Radius (km) Fig. 1.11. Models of P and S velocity V,, VS, density p, and temperature T i n the lower mantle. The super-adiabatic temperature profiles of PREM and L1 correspond to a homogeneous density (PEM profile), and the inhomogeneous density profiles correspond to the adiabatic temperature of PEM Absolute temperatures have been arbitrarily fixed. (After Doornbos, 1983.)
preted as reflections from their proposed discontinuity, must arise from a different cause. In PREM (see §1.7), the layer D" is 150 km thick, in which the pressure derivative of the bulk modulus, dkldp, has an anomalously low value of 1.64 as compared with an average of 3.2 for the overlying mantle. Since PREM
-
29
General Physical Properties of the Earth
shows no accompanying change in density or density gradient, Stacey and Loper (1983) identify D” as a thermal boundary layer and not as a chemically distinct zone. Although there is still controversy about compositional gradients, they maintain that the existence of a thermal boundary layer at the base of the mantle is necessary for the transfer of heat from the core through the mantle-a significant heat flux from the core is implied by any geodynamo mechanism (see $4.6). Using data on dk,/dp in D” from the PREM model and thermodynamic identities, Stacey and Loper concluded that the temperature increase across D” is 840 K. Such a layer cannot be a static feature, but must be maintained by a downward motion of lower mantle material towards the MCB with a strong horizontal flow near the bottom of D” confined to a layer at its base. Assuming a core heat flux of 1.6 x 10” W, they estimated the speed of the downward motion to be -0.07 mm y- and the thickness of the layer of horizontal flow at the base of the mantle a scale height of 11 km, much thinner than the thermal scale height (73 km). The thermal gradient at the base of the mantle is -9.6 K km-’ in fairly good agreement with that of Jones (1977) but considerably less than that implied from seismic studies of D” by Cleary (1974) and Doornbos and Mondt (1979b). Zharkov et al. (1985) investigated the convective stability of D”. They showed that it depends mainly on the value of the viscosity vMCB of the mantle at the MCB. D” is stable when v M ~ BN 10” poise and unstable when vMcBN 10’’ poise. They suggest that the thermal regime of D is not stationary. Relatively quiet long periods, when heat is transferred by conduction, end with the formation of a hot, locally unstable, layer (or spots) at the bottom of the mantle. This is followed by a comparatively short period during which the hot unstable layer disintegrates. Christensen (1984) has carried out a series of two-dimensional numerical model calculations to investigate the instability of a hot, low-viscosity boundary layer at the base of the mantle. The layer grows by thermal diffusion and becomes unstable, eventually leading to the formation and ascent of thermal plumes. When the temperature-induced viscosity contrast is as large as lo4, small-scale convection confined to the boundary layer precedes the ejection of a plume. The rise of the diapir is essentially controlled by the background viscosity and is slower than the rapid amplification of an instability inside the boundary layer. The application of Christensen’s results to the Earth is hampered by the idealization of the models and of the uncertain values of the parameters. In order to limit the heat flow from the core to a reasonable value, the lower mantle viscosity must be at least loz3poise when the temperature drop in the D” layer is of the order of 1000 K. This is larger than values derived from the analysis of post-glacial rebound (Sabadini and Peltier, 1981). The structure of the D” layer is still in doubt. A thermal boundary layer
-
’,
-
30
The Earth’s Core
seems to be necessary to provide a significant heat flux from the core demanded by any geodynamo mechanism. O n the other hand, a composition change in addition cannot be ruled out. A detailed account of the structure of the core and lower mantle has been given by Loper (1984). Seismological studies of lateral heterogeneity have determined the longestwavelength components of seismic velocity variations in the lower mantle (Dziewonski et al., 1977; Dziewonski, 1984). These velocity variations would be expected to be proportional to density variations if both were the result of temperature differences associated with mantle convection. However, the inferred density variations are negatively correlated with the geoid. This may be explained by counteracting effects of dynamically supported surface deformations in the gravity field, for example hot upwellings in the mantle cause uplift of the Earth’s surface and of the MCB. This dynamically maintained topography has a strong effect on the gravity field. Richards and Hager (1984) have shown that for a given density structure, the total gravity field depends on the viscosity structure and on the presence or absence of chemical stratification in the mantle. Hager et al. (1985) later showed that the longestwavelength components of the residual geoid can be predicted from the seismically determined density contrasts in the lower mantle using dynamic response functions for mantle convection with a moderate increase in viscosity with depth. They obtained long-wavelength temperature differences of the order of 20 K with hot lower mantle underlying hotspots at the Earth’s surface. The deformation of the MCB is 3 km.*
-
1.4 Free Oscillations of the Earth
When any part of a deformable body like the Earth is in motion, it may be regarded as either a vibrating system with an indefinite number of degrees of freedom or as a medium transmitting waves. Seismic wave theory regards the associated Earth motions as travelling disturbances affecting only a relatively small part of the Earth’s volume at any given time. Oscillation theory, on the other hand, regards the motions as normal modes of oscillation, the principal ones of which affect a relatively large fraction of the Earth’s volume at any instant. The wave theory approach is usually more appropriate for shorter periods (less than about 3 minutes), the oscillation approach for longer * A special issue of Geophysical Research Letters (Volume 13, No. 12) was published in December 1986 to commemorate the 50th anniversary of the discovery of the inner core by Inge Lehmann. The issue is devoted entirely to the geophysics of the core and core-mantle boundary and contains a number of papers on the structrure of the D layer. From an analysis of PKP phases, some authors suggest that a significant fraction of the hererogeneity at the MCB may actually reside in the fluid OC.
31
General Physical Properties of the Earth
periods. The relatively late application of free Earth oscillation theory is due to the fact that only recently could instruments record ground motions with periods greater than about 3 minutes. Free Earth oscillations were first observed in 1952, although it was not until the great Chilean earthquake of May 22, 1960, that improved instrumentation enabled detailed measurements to be made-additional results were obtained from the great Alaska earthquake of March 28, 1964. Although the free oscillations of a uniform elastic sphere were first investigated more than a hundred years ago, calculations for realistic Earth models taking into account detailed structure, gravitational forces and rotation were not undertaken until fairly recently (see e.g. Alterman et al., 1959). Such calculations would have been impossible without the aid of modern computers. The free oscillations excited by a major earthquake last for several days, but their amplitude diminishes because the Earth is not a perfectly elastic body. If spectra are computed for successive time intervals following the excitation, the damping of each mode can be determined and information on the anelasticity of the Earth's interior obtained. From an analysis of the normal modes from 84 recordings of the Alaska earthquake of March 1964, Dziewonski and Gilbert (1971,1972) concluded that the IC of the Earth must be solid. There are two main classes of oscillations. The first class are called torsional (or toroidal) oscillations-the dilatation is everywhere zero and there is no radial component of displacement. Since the dilatation is zero, torsional oscillations cause no disturbances in density and hence no disturbances in the gravitational field. Thus, instruments designed to measure small fluctuations in gravity cannot record torsional oscillations, although spheroidal oscillations may be detected. Spheroidal oscillations are coupled oscillations and involve radial displacements as well as torsional motions. The deformation of the Earth's surface is best described by spherical harmonic functions P r (cos where P," (cos 0) are the associated Legendre functions and 8,4 the co-latitude and longitude. Each class of vibration is characterized by the order m and degree n of the spherical harmonic involved and by the number of nodal surfaces in the radial direction. It has become general pracfor the spheroidal and tice to specify oscillations by the symbols l S r and toroidal types respectively, the subscript 1 indicating the number of nodal surfaces. The superscript m is dropped when there is no longitude dependence.* For the lowest values of n, the fundamental free Earth oscillation periods are determined predominantly by the properties of the Earth's deeper interior. For these values of n, the effect of lateral variations in the properties of the
$):I$
lr
* In much of the literature on the free oscillations of the Earth these symbols are written &" and .TY with the subscripts ( I , n) interchanged. We have, however, preserved the more common notation P y (cos 0) for the associated Legendre functions and use I to indicate the number of nodal surfaces.
32
The Earfhs Core
Earth on oscillation periods are negligible. For higher values of n, the periods become increasingly influenced by properties nearer the surface of the Earth, where lateral variations may be more significant. The fundamental spheroidal oscillation oSois an alternating compression and rarefaction of the whole Earth. There are an infinite series of overtones *So with spherical nodal surfaces within the Earth. The case n = 1 is precluded-it represents a net translation of the surface and hence of the centre of gravity and would require the application of an external force. oS2 represents the “football” mode. There are two nodal parallels of latitude dividing the surface into three zones. As the sphere oscillates, it is distorted alternately into an oblate and prolate spheroid. Spheroidal modes oS3, o S 4 . .. are motions with an increasing number of subdivided zonal distributionseach of these modes also has overtones with internal nodal surfaces. For torsional oscillations, there is no solution for n = 0. The case oT, is precluded. It implies a variation in the rate of rotation of the whole Earth, concentric shells within the Earth executing small rigid body rotations about the polar axis. The simplest torsional mode is oT2-in this case there is a nodal line for displacement around the equator, the two hemispheres oscillating in anti-phase. Higher modes arise from subdivisions of the Earth into 3,4 . . . zones with opposite motions. There are also overtones with internal nodal surfaces. For Earth models that are spherically symmetric and non-rotating, it is not necessary to include the parameter m-the oscillations may be described using only the two parameters ( I , n). For a rotating body it is necessary to include m. Travelling waves are set up where wavefronts are diametral planes containing the polar axis and revolving about it, either east-west or west-east depending on the sign of m. The longest free Earth oscillation periods (- 1 hour) are small compared with the axial rotation period (1 day). The effect of axial rotation is thus small. When it can be neglected, then for any value of m, the above east-west and west-east waves combine to produce standing waves (which are in reality oscillations) in which the frequency is independent of the value of m. Thus, an effect of axial rotation is to cause “split modes”, i.e. a small separation of a single mode into two or more distinct modes with slightly different periods. Backus and Gilbert (1961) showed that axial rotation causes the nodal pattern to drift westward round the Earth’s axis with angular speed equal to the frequency difference between successive members of the split mode. The Earth’s ellipticity contributes further to the splitting of modes. The records of free Earth oscillations show that the lowest frequency modes often appear as a number of closely spaced lines in the spectrum. Pekeris et at. (1961) suggested that this might be due to the rotation of the Earth splitting any mode having a longitude ( m ) dependence into a number of
33
General Physical Properties of the Earth
frequencies. They coined the term “terrestrial spectroscopy” for the study of free oscillation spectra, pointing out that the observed splitting of certain lines due to the Earth’s rotation is a mechanical analogue of the Zeeman splitting of lines of atomic spectra by a magnetic field. Smith (1974) obtained the equations of motion for a rotating, slightly elliptical, self-gravitating Earth, and later (1976) used them to generate numerical normal-mode eigensohtions for translational oscillations of the solid IC. Both he and Busse (1974) also pointed out the severe theoretical shortcomings of an earlier dynamic model of Won and Kuo (1973). Smith’s results show the profound influence of the Earth’s steady rotation, particularly on motions in the fluid OC. The variation of eigenfrequencies with core structure shows how stable (or unstable) stratification in the OC acts to increase (or decrease) the associated eigenfrequencies. O n the other hand, compressibility, as opposed to stratification, in the fluid OC is of little significance, but IC elasticity has a very significant effect. While convective circulation is not possible in a core that is everywhere sub-adiabatic, very-long-period gravitational oscillations (undertones) are possible. Because the gravitational restoring forces of a sub-adiabatic core are weak compared to the elastic restoring forces of free oscillations, the periods of vibration exceed the gravest free-oscillation periods. Although most freeoscillation spectra show prominent energy peaks at periods longer than the gravest elastic oscillation (53.8 min.), only recently have attempts been made to compute the expected periods. The first investigation was by Pekeris and Accad (1972). They ignored the Coriolis force and Smylie (1973) has since shown that this can have a significant effect on the periods. In his investigation, Smylie neglected the main magnetic field and assumed the liquid core to behave as an ideal fluid and calculated the undertones of the mode Si (azimuthal number m = 2, degree n = 2). Table 1.2 and Fig. 1.12 compare his TABLE 1.2 Gravitational undertone periods of S: in hours. (After Smylie, 1973.) Radial order
0’ 1 2 3 4 5 6
Pekeris and Accad (1972)
0.89583 7.3515 11.6735 16.0187 20.2618 24 3077
-
Coriolis-freet
0.89744 7.4524 12.4716 17.5474 22.3871 26.8703 -
Actual period
0.87125 6.7598 10.5285 13.8070 16.4970 18.6584 20.3377
* This is the gravest mode of vibration of the Earth.
t These periods differ from those of Pekeris and Accad (1972),presumably because of the presence of the solid inner core in the Earth model used in Smylie‘s study.
34
The Earths Core
35 I 30
1
1
z a
15
I
I
1
I
UNDERTONE EIGENPERIODS OF
2 25 3 0 I 20
I
I
I
1
1
Si MODE
-
WITH INNER CORE
WITHOUT INNER CORE
-
-4H-
-
-
INNER CORE AND CORlOLlS FORCE
3
0
I
I
I
I
I
1
I
I
I
UNDERTONE NUMBER Fig. 1.12. Dispersion relations for undertone eigenperiods of S: mode. The results for the Earth model without a solid IC are taken from Pekeris and Accad (1 972). (After Smylie, 1973.)
results (for different radial orders) with those of Pekeris and Accad, and show how the periods of the normal modes of a stable core are substantially reduced by rotation. These periods calculated by Pekeris and Accad neglecting rotation extend to infinity but become compressed to less than 1.5 days when rotation is included. In his analysis, Smylie (1974) considered the displacement field to be composed of purely spheroidal harmonics. Although torsional motion cannot exist independently in an inviscid fluid, torsional modes of oscillation can be excited when rotation is present. Crossley (1975) expanded the displacement field into both spheroidal and torsional components. He found that the periods of the undertones were considerably modified by rotation, which serves to couple together modes by the excitation of torsional motion. The undertones are confined within the period range 0-12 hours. Smylie has installed a specially designed gravimeter of extremely high sensitivity to try to detect possible core undertones, so far without success. Detection of such undertones (for which gravitation alone provides the restoring force) would constitute decisive evidence for stable stratification of the core and have far-reaching implications for geomagnetism and the thermal history of the Earth (See g4.6 and 3.8). Melchior and Ducarme (1985) have since installed a superconducting
35
General Physical Properties of the Earth
gravimeter at the Royal Observatory of Belgium in Brussels to try to detect inertial gravity oscillations in the Earth’s core. Such a gravimeter has a noise level 100 times less than that of a spring gravimeter. The superconducting gravimeter in Brussels has been recording without interruption since May 1981. After removing atmospheric pressure and polar motion effects, Melchior and Ducarme found spectral peaks of 1&15 nanogal around a period of 13.9 h which were enhanced immediately after two deep-focus earthquakes of magnitude 7.2. Crossley and Rochester (1980) had found a number of possible eigenperiods for a non-rotating Earth, including one at 13.458 h and one at 13.383 h. Friedlander (1985) showed that the effect of compressibility can produce a small shift in the frequency locations, although Crossley (1984) pointed out that in a rotating Earth the spectrum around 12 h is likely to be very dense and perhaps continuous (because of line broadening). The gravitational stability of the liquid core bears a direct relationship to the Adams-Williamson equation (1.10), which will be obtained later. If a fluid element is suddenly displaced radially by an amount Sr it suffers an adiabatic expansion and its density decreases by an amount equal to its initial density multiplied by its dilation, i.e.
where ( p o , go) are the equilibrium density and gravity and k, is the incompressibility. The displaced fluid element finds itself among neighbouring elements whose density is less than its initial density by the amount - (dpo/dr) Sr. The excess density of the displaced fluid element is thus
where P(r) = 1
dP0 +2 S O P 0 dr ks
a dimensionless factor originally introduced by Pekeris and Accad. It is clear that if P(r) < 0 everywhere, the liquid core is gravitationally stable (the restoring force is positive); if p(r) = 0, it is neutrally stable and if P(r) > 0 everywhere the core is gravitationally unstable. It should be noted that if the Adams-Williamson equation holds, i.e. if p ( r ) = 0, the liquid core is neutrally stable. Smylie showed that in the static case for spheroidal displacements of degree n 2 1, either the core must deform in such a way that the individual fluid elements, though displaced, suffer no dilatation, or the equilibrium density in
36
The Earths Core
the core must satisfy the Adams-Williamson equation. Smylie and Mansinha (1971) had earlier pointed out that, for fluids in static equilibrium, equipotential, isobaric and isopycnic (i.e. equal density) surfaces are parallel and that individual fluid elements may be displaced on such surfaces without resistance. Fluid elements are free to move aside on such surfaces to permit penetration of the solid IC and mantle into the liquid OC. Moreover, such surfaces not only remain parallel but are carried radially with the fluid element. There has been much confusion in the literature on the proper boundary conditions for the motions coupling the mantle with the liquid core, and different authors have come to different conclusions. Wunsch (1974) has shown that the essential difficulties and most of the physical phenomena can be reproduced in a much simplified model-the deformation in the static limit of an elastic half-space overlying a liquid half-space. He showed that, as is often the case in fluid dynamical problems, the problem is one of singular perturbation which leads to paradoxes if not handled correctly. Wunsch showed that in the case of the coupling of the motion of an elastic mantle to a stratified fluid core, the static limit is singular in a perfect fluid and can lead to physically meaningless results. Including rotation, however, makes the static limit a regular one, since Coriolis forces can support the deformed isopycnic surfaces in a steady flow. In a later paper (1975), Wunsch extended his analyses to include the effects of viscosity and density diffusion, and showed that paradoxes and contradictions that arise by treating only perfect fluids may be resolved by taking dissipation into account. Wunsch also considered the effect of a large ambient magnetic field-depending upon its orientation, its effect is similar to that of stratification or rotation. In particular, a toroidal field introduces a static limit singularity similar to that of density stratification. When a non-rotating spherical Earth model is used (Alterman et al., 1959), each spheroidal and toroidal component can be separated and the solution of the dynamic equation of equilibrium presents no major problems. Once rotation and ellipticity are taken into account, however, the spheroidal and toroidal fields become infinitely coupled (Smith, 1974; Shen and Mansinha, 1976). To circumvent the problem of infinite coupling, the effects of rotation and ellipticity can be considered as perturbations to a spherical, non-rotating Earth. This is feasible when the frequencies of the normal modes are much greater than the diurnal frequency. For elastic oscillations with periods of less than a sidereal hour, adequate results can be obtained with a first-order perturbation approximation (e.g. Backus and Gilbert, 1961; Pekeris et al., 1961; Dahlen, 1968; Luh, 1974). The approach fails, however, when long-period oscillations such as those confined mainly to the liquid OC are considered. Because the eigenperiods for these oscillations are comparable to or greater
37
General Physical Properties of the Earth
than the diurnal period, the full effects of rotation, and in some cases of ellipticity, must be taken into account. We then have an infinitely coupled system of ordinary differential equations. Traditionally, solutions of this system have been attempted by straightforward numerical integration (e.g. Smylie, 1974; Crossley, 1975; Shen and Mansinha, 1976; Johnson and Smylie, 1977; Crossley and Rochester, 1980). This approach, however, runs into the unavoidable problem of having to truncate the coupling chain severely and it is also difficult to interpret the numerical results. Shen (1983) has shown that by invoking appropriate approximations, analytic solutions can be developed for free oscillation of the Earth’s fluid OC. Crossley and Rochester (1980) attempted to justify certain approximations to their Earth model which permit more terms to be included in the expansion without increasing computer time. By considering simplified models of the Earth’s core they showed that, at least for the case of a non-rotating Earth, the effects of mantle structure and boundary rigidity on the undertone periods are minimal. Further, the combined effects of core compressibility and self-gravitation in a real Earth model can, to a good approximation, be replaced by a single parameter, the Brunt-Vaisala buoyancy frequency N.* Applying these simplifications to a rotating Earth model, Crossley and Rochester solved the resulting equations of motion with a longer coupling chain than any used previously. This approach, based on the chain beginning with the spheroidal term S;, supports the hypothesis that the periods of core undertones for a realistic rotating Earth model are crowded into a narrow band around 12 h. A different approach has been taken by Johnson and Smylie (1977) who used a variational procedure and considerable computational manipulation to include three spheroidal terms in the displacement field throughout the Earth. Figure 1.13 shows their results for the periods of the first few undertones of the spheroidal chain of azimuthal number two compared with earlier results obtained by direct integration. Moon (1982) has also used a variational procedure to derive seismic free oscillations and core modes for a rotating, slightly elliptical Earth model. He obtained numerical solutions for two Earth models (1066B and B156) minimizing the energy functionals for the terrestrial spectral range longer than the lowest-order free oscillation. For model B156, with stably stratified OC, the periods of core modes range from about 4-13 h with most of the modes crowded around periods of 6 h and 12 h. (Crossley and Rochester (1980) had shown that the periods for B156 are expected to be limited to the range * N is defined by the equation N2 =
-gdP-&
P d.r k, If the fluid is incompressible, the second term vanishes.
38
The Earths Core
24
0
t
I
2
3
I
1
1
4
5
6
UNDERTONE ORDER Fig. 1.13. Periods of the first few undertones of the spheroidal chain of azimuthal number 2. The curves show the effect of successive truncations. The case of no rotational coupling is due to Pekeris and Accad (1972) as modified by Smylie (1 974) to include a solid IC; the self-coupling case is due to Smylie (1974). who considered only rotational coupling of the first member of the spheroidal chain back on itself; coupling to T: was considered by Crossley (1975) in a direct integration of the equations of motion; and the case of coupling up to and including T; is due to Johnson and Smylie (1977). After Johnson and Smylie, 1977.)
between 6 and 12 h.) The core-mode periods for model 1066B are much more spread out without clustering around periods of 6 h and 12 h. Moon concluded that an Earth model can support long-period oscillations even when it is not stably stratified. According to the nature of the fluid motions and the primary driving force, free oscillations of the Earth’s core may be divided into two classes: gravitational oscillations and inertial oscillations. Gravitational oscillations are those that arise from density stratification in the core and are characterized by fluid flows in which the pressure variation due to compression is approxi-
General Physical Properties of the Earth
39
mately balanced by that due to transport (Shen, 1978; Smylie and Rochester, 1981). Inertial oscillations, on the other hand, are characterized by a predominantly solenoidal flow in the fluid and result from the rotation of the Earth (Greenspan, 1968). Shen (1983) argued that the equation of motion for inertial oscillations of the Earth’s core is identical in form to that of a nongravitating, homogeneous, incompressible fluid, density stratification coming in only when the change in gravitational potential is taken into account. Thus, the existence of inertial oscillations is independent of the density stratification in the liquid OC, in disagreement with the findings of Olson (1977) and Smylie and Rochester (1981). However, Shen agrees with Smylie and Rochester that the flow will be non-solenoidal for gravitational oscillations of the O C (undertones) in which density stratification is the principal governing factor. Smylie and Rochester showed that for sufficiently small (subacoustic) frequencies, an approximation that neglects the effect of flow pressure on the density is valid (they called this the “sub-seismic approximation”). This leads to a second-order partial differential equation in a single scalar variable, a great simplification from the original fourth-order partial differential vector equation. The validity of the sub-seismic approximation was first shown by Pekeris and Accad (1972) for gravitational oscillations of a fluid core in a non-rotating Earth using explicit solutions, and by Smylie and Rochester (1981) for a rotating Earth using scaling analysis. Shen (1983) showed that, despite Coriolis coupling, the sub-seismic equation can still be solved analytically for some core models. In a non-rotating Earth, gravitational oscillations are possible only for a stably stratified fluid core (Pekeris and Accad 1972). Shen showed, however, that with rotation gravitational oscillations become possible for any density stratification in the OC, the eigenfrequencies being divided into alternating allowed and forbidden zones. Furthermore, in each allowed zone, there exist an infinite number of such normal modes with their eigenfrequencies approaching asymptotically the eigenfrequency of a corresponding inertial oscillation. Both the solenoidal flow approximation (for inertial oscillations) and the sub-seismic approximation (for gravitational oscillations) ignore the fluid flow arising from variations in gravitational potential. Shen developed an asymptotic formulation to allow for this as well as taking into account deformation of the solid part of the Earth. He showed that the eigenfrequencies can be determined without explicitly solving for the correction terms.
1.5 Attenuation in the Earth
Most models based on free-oscillation periods assume that the elastic proper-
40
The Earth’s Core
ties of the Earth are independent of frequency. It is well known that absorption decreases the intrinsic elastic properties and causes velocity dispersion (Zener, 1948). This means that laboratory, body wave, surface wave, and freeoscillation data cannot be directly compared unless the absorptiondispersion correction is applied. The effect of absorption on free oscillation periods was initially ignored, however. Serious discrepancies were found with body wave results, which were attributed to a “baseline” effect, a presumed difference between the average Earth and that sampled by body wave data. Later, the effects of absorption on dispersion were re-examined and found to be of the first-order as Jeffreys (1965) had all along maintained, and not second-order as was initially assumed. The damping of free oscillations changes, for example, the eigenfrequencies of oT2 and oSz by about 0.5 and 0.25% (13 and 8 s) respectively (Randall, 1976; Hart et al., 1977). Jeffreys (1967) pointed out that for any form of imperfection of elasticity, except elasticoviscosity, there must be a systematic lengthening of free periods that may be about one part in 160. Thus, Earth models obtained by inversion of uncorrected normal mode data will yield lower velocities than models based on body wave data. The method for correcting seismic data has been given by Liu et al. (1976) and consistent Earth models have been determined by Hart et al. (1976). The physical dispersion accompanying absorption also complicates comparisons of laboratory and seismic data since they are taken at quite different frequencies. This must be taken into account in attempting to infer the composition of the Earth by comparing laboratory and seismic data. A large number of body wave observations are consistent with a low-Q zone at the bottom of the mantle.* Mikumo and Kurita (1968) estimated a 300-km thick layer at the base with QP 100. Teng (1968) determined the variation of Q with depth from the spectra of P phases from deep earthquakes. His data indicate a 200-km thick zone with QP 200. The observed amplitude ratios of ScS/S of Mitchell and Helmberger (1973) can be interpreted in terms of a thin low-Q zone (approximately 150 km thick with Qs about 100). The amplitudes of grazing P K P phases (Sacks and Snoke, 1976) also indicate a low-Q zone at the base of the mantle, Kuster (1972) proposed a low-Q zone (QP = 300, thickness 150 km) on the basis of P K P and P K K P spectral amplitude ratios. Berzon, et al. (1974) estimated the attenuation parameter QP in the mantle based on changes in the form of P-wave amplitude spectra as a function of distance. They used two independent sets of data from narrow-band and wide-band seismometers. They found the average value of QP in the depth in-
-
-
* Q has already been defined on page 16. Q for P waves is denoted by QP and for S waves by Q-in some papers by Q,. Often the subscript is omitted if there is no confusion about which Q is being discussed.
41
General Physical Properties of the Earth
TABLE 1.3 Comparison of Qpvalues in the upper and lower mantle. (After Berzon etal., 1974.)
0,according to: Depth interval (km)
Velocity Values used (krns-’)
Berzon eta/. (1974)
Anderson
~- et al.
lstset
2ndset
100-760
9.04
760-2900
12.48
710 k 150 + 730 1330- 360 1200:
100-2900
11.45
+ 420 1080- 285
0-100 0-760
7.62 8.91
0-2900
11.29
220 5 3 0 k 150 + 420 845 - 260
,”7”,”
(1965)
Kanamori (1967a) (1967b)
380
165
3210
1210
990
420
230 345
100 150
850
375
0-900 900-2900
410-630
Mikumo and Kurita (1968) M-5 M-14
1690
4900
120
274
292
702
180-240 1600-6000
terval 100-760 km to be 710 and in the interval 76@2900 km to be between 1200 and 1330. Table 1.3 compares their values with those obtained by other investigators using different methods. The differences are most likely due to the different data used (particularly the different frequency ranges) and the methods of analysis. Canas and Bolt (1983) showed that the ratio of the observed amplitudes of PcP and PcS phases at a station from the same earthquake is directly related to the density ratio at the MCB and the average attenuation parameter Qs for the mantle. Later Bolt and Canas (1985) obtained clear wave pulses at Berkeley and Jamestown for three earthquakes giving reflections at the MCB under both continental and oceanic areas. Comparison with plausible Earth models confirms a density jump at the MCB of 1.7. The average mantle Qsvalues under continental and oceanic regions are 705 f 365 and 585 ? 305, giving a mean of 650 k 335, in general agreement with results from surface waves. Agreement between observations and theoretical models is best if it is assumed that Qs increases with frequency o as oawhere c1 also increases with frequency. The Q of the O C is extremely high. High-frequency PnKP phases ( P K P , P K K P , P K K K P , etc.) travel with little change in shape or amplitude for long distances. Cormier and Richards (1976) concluded that QP in the OC is at least lo4 and probably much higher. A high Q for the O C is also supported by studies by Buchbinder (1971), Sacks (1971a, 1972), Adams (1972), Miiller (1973) and Qamar and Eisenberg (1974). Most of these studies infer a Q greater than 4000. It must be pointed out, however, that part of these differences in Q-values may be due to differences in the period ranges upon which
-
42
The Earths Core
the estimates were based. Qamar and Eisenberg’s investigation used spectral ratios of seismic core waves. For seismic waves of frequencyf2 1 Hz they found a high value of Q( 2 5000) in the OC. This was based on the fact that PnKP phases were observed for large values of n (at least n = 7): the P7KP/ P4KP ratios suggest a Q in the range 400CL8000, while the average slope of the P7KPIP4KP spectral ratio yields Q 11 10,000. Qamar and Eisenberg’s analysis, which assumed the applicability of classical ray theory and plane wave reflection coefficients, could not explain the observation that P7KP has consistently greater high-frequency content than P4KP. They suggested that frequency dependence of the MCB reflectiontransmission coefficients (Richards, 1973) may be important even in the highfrequency range of their study (0.2-2.0 Hz). Cormier and Richards (1976) later showed that this was in fact the case, and put a lower bound to Q in the oc of 10,000. There have been a number of body wave measurements of dissipation in the IC. Buchbinder (1971), using P K P amplitude ratios, found an average value of Q in the IC of about 400. Spectral ratios of IC and OC phases (Sacks, 1971b) indicate an average value of Q in the IC of 600. Sacks’ data suggest that QP is not constant through the IC but ranges from 100 to 200 in the outer 300 km to 1000 at greater depths. Kuster (1972) found a value of 300 for QP from spectral ratios of core phases. Julian et al. (1972) estimated that Q, in the IC is between 500 and 1000. A high value for Q, in this region is also implied by the fact that IC shear modes (e.g. 2S2) are observed (Buland and Gilbert, 1978). The Q of 2 S 2 implies a Q, for the IC of about 550. For the outer 450 km of the IC, Qamar and Eisenberg (1974) using the P K I K P I P K P ratio, obtained a value of Q in the range 120-1400, more than an order of magnitude less than that in the OC. Doornbos (1974) studied the anelasticity of the IC using spectral ratios of short-period core phases with common source and receiver and with nearly the same ray paths in the mantle. For 1 Hz compressional waves, he found that Q rises from a value of about 200 near the ICB to about 600 at a depth of 400km inside the IC. Below 450km from the boundary, the Q structure cannot be determined with any precision but is probably less than 2000. From observations of high-Q normal modes with a high energy concentration in the IC, Doornbos found a suggestion that, over a wider frequency range, Q is frequency-dependent. A frequency-dependent Q with low Q values around 1 Hz is compatible with partial melting in the IC. He suggested that at the ICB the temperature is close to the melting point and that in the IC the temperature gradient only slightly exceeds the melting point gradient (see also 63.6). From a spectral analysis of the phases PKZZKP and P K i K P from the same record, Bolt (1977) obtained a mean QP of 450 f (100) in the IC. Akopyan et al. (1975, 1976), Liu et al. (1976) and Hart et al. (1977) tackled
General Physical Properties of the Earth
43
the problem of dispersion caused by the Earth’s anelasticity by “correcting” the observed eigenperiods for attenuation before performing inversion to find an Earth model. This procedure can eliminate the “base-line” problem mentioned above-that travel times predicted by Earth models derived from free oscillations are generally slower than those predicted by Earth models derived from body waves. Lee and Solomon (1978), in a study of surface waves, showed that it is strictly more correct to perform simultaneous inversion for elastic and anelastic properties, rather than “correcting” some of the observations. Sailor and Dziewonski (1978) attempted to obtain the anelastic properties of the average Earth. As a first approximation, they considered the anelastic properties separately, without taking into account the coupling to elastic properties. In spite of the known lateral heterogeneity of both elastic and anelastic properties of the Earth, it is still useful to consider the concept of a spherically symmetric average Earth. The average Earth can serve as a standard of comparison for seismic observations made in more limited regions. Sailor and Dziewonski derived models of the gross Earth attenuation and found no indication of frequency dependence of Q in the period range from 100 to 3000 s. They obtained more than 230 Q measurements, using two different techniques-individual LaCoste-Romberg gravimeter recordings of three large earthquakes and 211 WWSSN recordings of two deep earthquakes. They inverted these data to obtain models of the distribution of Q in the mantle. The data-space inversion gave no indication of large variations of Q in the lower mantle-the data being consistent with very simple Q models. The data for modes dominated by shear energy can be satisfied by models with constant Q,-’ (attenuation of shear energy) in two regions: the upper mantle in which Q, is about 110, and the lower mantle below 670 km, in which Q, is a little below 400. The average Q, of the mantle is about 210. Models in which only shear energy is dissipated do not satisfy the observations of Q for radial modes. They also found that Q K (bulk dissipation) is finite in the upper mantle and possibly in the IC. Simultaneous inversion for Q, and QK showed that the data can be satisfied if QK is infinite in the IC and lower mantle, but finite in the upper mantle. Anderson and Hart (1978a) revised their earlier Q model MM8 for the Earth (Anderson et al., 1965). Their data set included fundamental and overtone observations of radial, spheroidal and toroidal modes, ScS observations and amplitudes of body waves as a function of distance. Their preferred model includes a low-Q zone at both the top and bottom of the mantle. Absorption in the mantle is predominantly due to losses in shear, although in the IC compressional absorption may be important as well. Most of the attenuation data can be satisfied by a frequency-independent Q versus depth model. Although Q is probably frequency-dependent in the high-Q regions of
-
44
The Earths Core
the Earth (the lithosphere and mid-mantle, (200-2000 km)), it is the low-Q regions of the Earth, where Q is only weakly dependent on frequency, that dominate the absorption of teleseismic body waves and normal modes. Anderson and Hart interpreted their Q model in terms of a thermally activated relaxation process that involves a distribution of activation energies and a small activation volume. A grain boundary relaxation model explains the dominance of shear over compressional dissipation, the roughly frequency-independent average value for Q and the variation of Q with depth. In a later paper Anderson and Hart (197%) made further estimates of the variation of Q with depth in the Earth. Their approach was to construct models based on body wave data and then to test and modify these models in order to satisfy the normal-mode data. Most of the attenuation data are consistent with frequency-independent Q versus depth models. They found that Q increases smoothly with depth over most of the lower mantle with a low-Q zone at its base. Normal-mode and body wave data indicate that there is bulk and shear dissipation in the IC, although no bulk dissipation is required in the mantle. Table 1.4 and Fig. 1.14 show the values of Q for their preferred model. Cormier (1981) synthesized short-period (0.2-2 Hz) seismograms for P K P waves interacting with the IC in anelastic Earth models. The agreement he obtained between predicted and observed amplitudes and spectral ratios requires neither a low-Q zone nor a low- or negative-P velocity gradient at the bottom of the OC. Thin low-Q, zones beneath the ICB fit the spectral data that sample the upper 200 km of the IC but fail to fit data that sample the lower IC. Only models having Q p 280, nearly constant with depth in the IC, satisfy all the spectral ratio and amplitude data. This suggests nearly constant temperature, pressure and phase composition with depth in the IC. The closeness to the melting temperature of some thermal models of the IC (see $3.6) suggests that the anelasticity may be due to partial melting. The amplitude of a mode at its resonant frequency is proportional to its Q. Thus even a weakly excited core mode (i.e. a spheroidal mode of elasticgravitational oscillation that has an energy partition dominated by shear energy in the IC) may be observable if Qs in the IC is high. Masters and Gilbert (1981), using recordings from the IDA gravimeter network of an earthquake in the Tonga region, obtained the first unambiguous observations of core modes. At low frequencies, the IC has a very high Q (about 3500) Core modes are extremely sensitive to the travel-time of shear waves in the IC. Masters and Gilbert computed the frequencies of the identified core modes using a constant shear velocity in the IC and a variable IC radius. The calculations are insensitive to structure above the ICB and frequencies computed using models 1066A and 1066B (Gilbert and Dziewonski, 1975) differ by less than 1 pHz. The observations are consistent with a low-frequency
-
TABLE 1.4 Q model SL8. (After Anderson and Hart, 1978b ) Thickness
Qs
Q P
(km) ~~
6371 00 6365 50 6360 00 6325 79 6291 62 6257 46 6223 29 618913 6154 97 61 20 80 6086 64 6052 17 601 8 31 5984 15 5950 00 5908 30 5866 64 5824 97 5783 31 5741 65 5700 00 561 3 93 5527 00 5440 09 5353 15 5266 23 51 79 39 5092 39 5005 47 491 8 54 4831 62 4744 70 4657 78 4570 86 4483 93 4397 02 431 0 09 4223 18 41 36 25 4049 33 3962 41 3875 48 3788 55 3701 62 361 4 70 3527 76 3484 30 2326 40 1229 50 61475
5 50 5 50 34 20 34 16 34 16 34 16 34 16 34 16 34 16 34 16 34 16 34 16 34 16 34 16 41 68 41 66 41 66 41 66 41 66 41 66 86 06 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 92 86 93 86 93 86 93 86 93 86 93 86 93 43 46 115787 1096 92 614 75 614 75
00 5 50 1 1 00 45 20 79 37 11353 147 70 181 86 21 6 02 250 19 284 35 31 8 52 352 68 386 84 421 00 462 69 504 35 546 02 587 68 629 34 671 00 757 07 843 99 930 91 101784 110476 1191 68 1278 60 1365 52 1452 45 1539 37 1626 29 171321 180013 1887 06 1973 98 2060 90 2147 82 2234 74 2321 67 2408 59 2495 52 2582 45 2669 38 2756 30 2843 24 2886 70 4044 60 5141 50 5756 25
Read 0.1OOE - 05 as 0.100
X
1 O-’.
500 00 500 00 500 00 11000 90 00 90 00 105 00 105 00 105 00 105 00 105 00 105 00 120 00 124 00 140 00 150 00 166 00 180 00 196 00 21 5 00 230 00 260 00 287 00 31 0 00 338 00 360 00 370 00 390 00 41 0 00 425 00 440 00 455 00 465 00 477 00 485 00 495 00 505 00 510 00 51500 51 5 00 515 00 51 0 00 500 00 300 00 200 00 100 00 0 00 0 00 425 00 850 00
1242 22 124411 1047 31 240 20 207 14 218 50 265 92 273 85 279 38 282 06 282 18 280 41 317 59 324 98 363 50 386 40 424 59 457 15 494 09 537 10 566 31 631 43 691 66 744 03 81218 871 42 905 02 963 85 1022 26 1067 57 111251 115709 118794 1221 83 1242 57 1266 60 1291 80 1308 10 1329 50 1342 44 1357 89 1359 37 1343 27 809 24 539 77 268 99 1 000,00000 1,000,00000 425 00 850 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 0 100E - 05 0 lOOE - 05 0 235E - 02 0 118E- 02
46
The Earth's Core
0
0
100
200
300
QP 400 500
600
700
800
J
,-
500 -
Model SL8 I000 -
1500-
2000 -
E
1
-
v
2500-
a
Q,
D
Outer Core
4871 -
Q,= co
5371 -
Fig. 1.14. 0 model SL8. (After Anderson and Hart, 1978b.)
travel-time of shear waves (radius/mean shear velocity) in the IC of 345 f 1.5 s. Stiller et al. (1980) have given two possible explanations for the distribution of the attenuation coefficient Q-' in the Earth's core. An appreciable asymmetric peak occurs at the ICB (see Fig. 1.15). It is somewhat surprising that the attenuation is higher in the solid IC than in the liquid OC, since one would expect sound waves to be generally damped less in solids than in their melts. Doornbos (1974) suggested that this is due to partial melting in the IC. Stiller et al. discuss two possible mechanisms that could explain the large anelasticity in the IC: one takes into account slow relaxation processes near
47
General Physical Properties of the Earth
4 5-
4-
3c
I
Q
m
0 2-
1 -
--
1
-.-
, tl200
ICB
I
I 1000
I
-------- - - _ _ _ _ _ _ I 800
I
1
I
600
I 400
I
I 200
I
3
I 0
Radius (km )
Fig. 1.15. Attenuation coefficient of seismic P waves in the Earth’s core. 1, data of Doornbos (1 974). 2, relaxation model of Stiller e t a / . (1980) with temperature distribution of Higgins and Kennedy (1 971). 3,relaxation model of Stiller et a/. (1980) with temperature distribution of Stacey (1 977); 4, contribution from attenuation in inhomogeneous matter (second model). (In the paper of Higgins and Kennedy the ICB is located at a different depth from that in the papers of Doornbos and Stacey). (After Stiller, Franck and Schmidt, 1980.)
the melting transition at the ICB, and the other is a quasi-polycrystalline structure for the IC. The first mechanism via slow order parameter relaxation can account for the shape of the Q - curve for the Earth’s core if Higgins and Kennedy’s (1971) temperature distribution is used (see Fig. 1.15). This explanation is a direct result of the condition that the whole IC, although solid, is very close to its melting temperature or solidus. Stiller et al. prefer this mechanism. The second mechanism would be more likely if the temperature distribution in the IC is like that of Stacey (1977), in which case the order parameter relaxation effect cannot account for the high energy loss in the lower 1000 km of the core. Karato (1980) has estimated temperatures in the lower mantle from the distribution of Q. He found a thermal boundary layer at the base of the mantle corresponding to the low-Q zone found by Anderson and Hart (1978a,b). This is not really surprising, but the accuracy of such temperature determinations is very dependent on that of Q, which is not at all well-known.
48
The Earths Core
1.6 Variation of Density and Other Physical Properties within the Earth
The density p will depend on the pressure p , the temperature T, and an indefinite number of parameter nispecifying the chemical composition, i.e. P = P ( P , T,ni)
(1.5)
If m is the mass of material within a sphere of radius r, then, since the stress in the Earth's interior is essentially equivalent to a hydrostatic pressure,* dP dr
- = -9P
where g=-
Gm
(1.7)
r2
and G is the gravitational constant. Considering first a chemically homogeneous layer in which the temperature variation is adiabatic, it follows from (1.5) that nP-----dPdP - - 9 P 2 dr - d p dr k, where k, is the adiabatic incompressibility defined by the equation
where s is entropy. A homogeneous region is here defined as one in which there are no significant changes of either phase or chemical composition. It follows from (1.7), (1.8) and (1.3) that dp
dr
-
-Gmp2 - -Gmp -~
ksr2
rz 4
(1.10)
The distribution of 4 throughout the Earth is known from the velocity-depth curves (cf. 1.3). Since dmldr = 47cpr2, a second-order differential equation for p = p ( r ) can be written down by differentiating (1.10). This equation, first obtained by
* In the deeper interior of the Earth, strains are fairly large (e.g. near the MCB, the mean of the principal strains has magnitude about 0.14). The mean (+pix) of the principal stresses is correspondingly large. In contrast the strength of the materials in the Earth, and therefore the greatest deviatoric stresses that can be attained, is small, i.e. the ratio of any pi, to fp,.. (which corresponds to pressure) is small at depths greater than -50 km and diminishes steadily as the depth increases. We can thus neglect the p,, compared with j p k k in the Earth's deep interior and treat the internal stresses of the Earth, when in its equilibrium state, as hydrostatic.
General Physical Properties of the Earth
49
Adams and Williamson in 1923 (Williamson and Adams, 1923), may be integrated numerically to obtain the density distribution in those regions of the Earth where chemical and non-adiabatic temperature variations may be neglected. Any density distribution must satisfy two conditions-it must yield the correct total mass of the Earth and the moment of inertia about its rotational axis. Using these two conditions and a value p1 of 3.32 g cm-3 for p at the top of layer B of the mantle (assumed to be at a depth of 33 km), Bullen applied (1.10) throughout the regions B, C and D. He then found that this led to a value of the moment of inertia I , of the core greater than that of a uniform sphere of the same size and mass. This would entail the density to decrease with depth in the core and would be an unstable state in a fluid. Birch (1952) showed that a non-adiabatic temperature gradient only worsened the situation. A reasonable value for I , could be obtained by increasing the initial value of pl, but only if an impossibly high value (at least 3.7 gem-' were chosen. Thus the assumption of chemical homogeneity must be in error; the region where this assumption is most likely to be invalid is region C where there are large changes in the slope of the velocity-depth curves. In his original Earth Model A, Bullen thus used the Adams-Williamson equation (1.10) in regions B and D while in region C he fitted a quadratic expression in r for p = p(r). In the O C (region E) (1.10) is likely to apply, and values of p down to a depth of about 5000 km can be obtained with some confidence. In the core one boundary condition is m = 0 at Y = 0, but lack of evidence on the value of the density p o at the centre of the Earth leads to some indeterminacy in the density distribution in regions F and G. Bullen initially derived density distributions on two fairly extreme hypotheses: (i) p o = 12.3 g cmP3and (ii) p o = 22.3 g cm-3 (this value being taken quite arbitrarily). A model with density values midway between those of these two hypotheses has been called Model A. More recent evidence indicates that p o is probably much nearer its minimum value and that a model based on po = 12.3 (Model A-i) is more likely to be correct.* These earlier determinations of the density distribution only made use of the information contained in the velocity-depth curves. The biggest source of additional information has come from analyses of the free vibrations of the Earth excited by major earthquakes. None of the existing velocity-depth curves combined with Bullen’s density distribution were consistent with the longer-period free-oscillation data obtained from the great Chilean earthquake of May 22,1960, and the great Alaska earthquake of March 28,1964. Using this additional data Landisman et al. (1965) investigated a number * A good account of this early work can be found in Bullen (1963,1975).
50
The Earth's Core
of Earth models without assuming homogeneity and an adiabatic temperature gradient (except in the OC). A feature of their models is constant density between depths of about 1600 and 2800 km. Bullen and Haddon (see later), were able to avoid this very implausible conclusion by treating the radius of the core rc as a free parameter-a normal value of the density gradient in the lower mantle could be obtained by increasing r, by about 15 km. Dorman et al. had earlier (1965) proposed an Earth model in which rc was increased by 10 km. Pekeris (1966) also obtained density distributions in the Earth without assuming homogeneity and an adiabatic temperature gradient in any region of the Earth. His density distribution p ( r ) was represented by 50 pivotal values p(rk) with linear variations in between and with discontinuities at the base of the crust and at the MCB. Pekeris varied the p k by the method of steepest descent so as to minimize the sum of the squares of the residuals of all the observed periods of the free oscillations of the Earth. As might be expected the density distribution in the IC has little effect on the spectrum as a whole. Other workers have supplemented the travel-time data with experimental empirical data. Birch (1960, 1961a,b, 1964) used an approximate linear relationship between density and the velocity of compressional waves that he had observed for silicates and oxides of about the same iron content, viz. p = a(m)
+ bVp
(1.11)
where m is the mean atomic weight. Birch only used this equation in the upper mantle (where there are high thermal gradients) and the transition zone (where there are phase changes). In the rest of the Earth he used the Adams-Williamson equation. A relationship between p and V , was proposed by Simmons (1964) and verified by Christensen (1966). McQueen et al. (1964) suggested that a better estimate of the density in the upper mantle might be obtained by using an empirical relationship between the bulk sound velocity c = (V: - SVi)* and density p rather than Birch's relation ( 1 . 1 1) between V p and p. This was verified by Wang (1968,1970). Birch's law implies a unique relationship between V pand p for materials of common atomic weight irrespective of whether density changes are due to crystallographic structure, pressure, or temperature. Liebermann and Ringwood (1973) obtained data for low- and high-pressure polymorphs for a wide variety of crystallographic phase transformations likely to be important in the Earth's interior. Their data indicate that V p - p relationships across such polymorphic transformations are not always equivalent to V p- p changes caused by varying pressure, temperature, or composition at constant mean atomic weight.
General Ph ysical Properties of the Earth
51
Chung (1974) obtained ultrasonic data on some crustal structures important in mantle minerology, using a powder-matrix method (Simmons and Chung, 1968) in which the elastic parameters of the unknown material are inferred from the measured elastic parameters of a composite made of the powdered material imbedded in a vacuum hot-pressed matrix of AgCI. Chung showed that a power law describes the velocitydensity (V,, ,J relationship for high-pressure polymorphs better than Birch’s linear law. In particular he found that V , varied quite linearly with density over very wide density (and thus wide pressure) ranges for materials of lower mean atomic weight, the linearity even being preserved through solid-solid phase transformations. For materials of higher mean atomic weight, on the other hand, evidence for linearity is weak. In a later paper Shankland and Chung (1974) obtained a power law equation for the dependence of V, upon m and p . Birch’s linear law and Anderson’s (1967) seismic equation of state may be deduced from it as special cases. Anderson (1973) has reviewed the literature on the power law representation of Birch’s law. Clark and Ringwood (1964) and Wang (1972) estimated densities in the Earth using petrological models for the upper mantle. Mizutani and Abe (1972) obtained an Earth model consistent with all the data using a trial-and-error method with the help of an equation of state of some rock-forming minerals. It must be emphasized that the overall density distribution within the Earth is not changed drastically by taking into account the additional observational data on its free vibrations and the revised estimate of its moment of inertia about its axis of rotation as determined from analyses of the orbits of artificial satellites (Cook, 1963). Inside the mantle, the largest difference in p between models A-i and HB, (to be discussed later) is only 0.15 gcm-3, while inside the core the values of p in model HB, exceed those in model A-i at all depths by amounts between 0.2 and 0.3 g ~ m - ~ . Buchbinder (1968) carried out a detailed study of PcP phases from eight explosions and three earthquakes. He reported cases of reversed polarity of PcP phases relative to P for epicentral distances < 32” at which distance the amplitudes of PcP pass through a minimum. Buchbinder suggested that these results reflect properties at the MCB that cannot be satisfied by any of the ‘‘conventional’’ Earth models. He found that the velocity at the top of the core is some 7-8% lower than values usually quoted and that there is no density discontinuity across the MCB. Buchbinder interpreted his results to indicate that the bottom of the mantle is inhomogeneous-the inhomogeneity being caused by an increase in iron (or other heavy metal) content with depth that increases the mean atomic weight and density with but little change in P velocity. The drop in P velocity across the MCB may then be explained by a discontinuous increase in mean atomic weight with but little change in density.
52
The Earth's Core
Various authors have objected to Buchbinder's interpretation. Berzon et al. (1972) noted that PcP phases are observed near 30" as frequently as at other epicentral distances, thus ruling out a zero in amplitude. Kogan (1972) demonstrated, by correlation between P and PcP phases, that PcP phases do not invert their polarity. Chowdhury and Frasier (1973) carried out an analysis of short-period P and PcP phases from earthquakes in the range 26" < A < 40" from the Large-Aperture Seismic Array (LASA) in Montana. No reversals of PcP polarity for A < 32" and no minimum in amplitudes at 32" were observed-again ruling out Buchbinder's model and favouring the more conventional models with a density ratio at the MCB of about 1.7. Buchbinder himself has now abandoned his original interpretation. A different approach to the inverse problem is the Monte Carlo method described in its geophysical context by Keilis-Borok and Yanovskaya (1967). It was used by Press (1968a,b) to obtain a number of Earth models using as data 97 eigenperiods, travel-times of P and S waves and the mass and moment of inertia of the Earth. The Monte Carlo method uses random selection to generate large numbers of models in a computer, subjecting each model to a test against geophysical data. Only those models whose properties fit the data within prescribed limits are retained. This procedure has the advantage of finding models without bias from preconceived or over-simplified ideas of Earth structure. Monte Carlo methods also offer the advantage of exploring the range of possible solutions and indicate the degree of uniqueness obtainable with currently available geophysical data. Press was able later (1970a,b) considerably to speed up his Monte Carlo procedures. Using new and more accurate data he was able to find a large number of successful models and also confirmed that the Earth's core is inhomogeneous and that the density at the top of the core is constrained to the narrow range 9.9-10.2 g cmP3.Wiggins (1969) also used Monte Carlo techniques to investigate the nature of the non-uniqueness inherent in the interpretation of body wave data. Haddon and Bullen (1969) constructed a series of Earth models (HB) using free oscillation data consisting of the observed periods of fundamental spheroidal and toroidal oscillations for 0 Q n Q 48 and 2 Q n Q 44 respectively and certain spheroidal overtones. Data from the records of both the Chilean and Alaskan earthquakes were used. Their procedure was to start from models derived independently of the oscillation data and to produce a sequence of models showing improved agreement with all the available data. In passing from one model to the next, a guiding principle was to introduce and vary one or more of the parameters in the model description at any stage in order to satisfy the oscillation data. They thus tried to establish models described in terms of the minimum number of parameters demanded by the data. A major difference in principle between their method and the Monte Carlo procedure
General Physical Properties of the Earth
53
of Press is the comparatively large number of parameters that Press permits to be randomly varied. Haddon and Bullen pointed out that the predominance of complex models found by Press is inherent in his method, since a simple random walk would automatically have a low probability. Haddon and Bullen also stressed that the “average” Earth to which average periods of free-oscillation modes relate is not necessarily the same as an Earth model to which the currently available average seismic body wave travel-times apply, since earthquake epicentres and recording stations are not randomly distributed over the Earth’s surface. In 1970, Bullen and Haddon used additional evidence to derive an improved Earth model (HB,). Model HB2 incorporated the newer P travel-time data of Herrin (1968) and takes into account the abnormalities in the body wave observations in the lower 200 km of the mantle and the detailed structure of the lower core (Bullen, 1965). In their earlier model HB1 a simplified core structure was assumed (the whole core being considered fluid), since free Earth oscillation data are incapable at present of resolving fine detail in the lower core. Derr (1969) also developed a series of Earth models using freeoscillation data. Anderssen and Seneta (1971, 1972) examined in detail the Monte Carlo method of inversion of geophysical data: in particular they developed a statistical procedure for estimating the reliability of non-uniqueness bounds defined by a family of randomly generated models. Anderssen et a / . (1972) applied these techniques to the problem of obtaining the density distribution within the Earth, and in a later paper (Worthington et al., 1972) attempted to resolve the major discrepancies between the density models of Bullen and Haddon and those of Press. They showed that these differences cannot be due to the different techniques employed to derive the models, and concluded that they are predominantly due to differences in assumptions about the permissible range of values of the shear velocity in the upper mantle. An upper bound to the density increase at the ICB was obtained by Bolt and Qamar (1970) from measured amplitudes of P K i K P and PcP phases recorded at LASA in Montana. The P K i K P waves were reflected at steep angles from the ICB (epicentral distance A (40”) and demonstrate the sharpness of that boundary (Engdahl et a!., 1970). Bolt and Qamar’s analysis indicated a minimum value of 0.875 for the ratio of the densities at the ICB. This would give a maximum density jump Apic at the ICB of 1.8 g cm-3 if the density in the O C at the boundary is 12.35 g cm-3 (see also Bolt, 1972). This result has been obtained on seismological evidence alone and does not depend on any assumptions concerning the chemical composition of the core. It is also in agreement with recent core models that indicate that the density in the IC is much lower than was at one time supposed. Dziewonski (1971) has stressed that only observations of overtones will
54
The Earths Core
allow the density distribution to be determined with sufficient detail to enable meaningful estimates of the structure and composition of the Earth’s deep interior. The diversity of models that satisfy travel-time and fundamental mode data indicates the insufficiency of the constraints provided by the more limited set of data. Dziewonski was able to identify overtones with periods greater than 250-300 s on records of the March 1964 Alaska earthquake from stations belonging to the WWSSN. Using this additional information, he constructed a number of Earth models. His final models indicate a change in composition in the bottom 500 km of the mantle. His density distributions show systematic differences from the HB1 model and Press’s models in the lower mantle, although all models lie within Press’s band of solutionsexcept that lower shear velocities are found in the depth range 480-650 km. Although agreement with these other models is good for the fundamental modes and the first two spheroidal overtones, it is poor for the third and fourth spheroidal and torsional overtones. A solid IC is also demanded by Dziewonski’s data-if the shear velocity in the IC is 3.5 km s - ’ Apic = 0.81 gcm-3. Details of the most recent Earth models are given in the next section. From (1.6) and (1.7). it follows that (1.12)
Hence by numerical integration, the pressure distribution may be obtained once the density distribution has been determined. Since the density is used only to determine the pressure gradient, the pressure distribution is insensitive to small changes in the density distribution and may be determined quite accurately. The variation of g can be calculated from (1.7). From a knowledge of the density distribution it is easy to compute values of the elastic constants. Thus (1.2) and (1.3) give p and ks directly. Poisson’s ratio r~ can be expressed in terms of V, and V, or ks and p; viz. o=
V; - 2V: 2(V; - Vg)
3k.y - 2 p 6ks + 2p
=-
(1.13)
Estimates of the IC radius compatible with differential P K i K p travel-times (Engdahl et al., 1974) correspond to a shear velocity of 3.55 ? .03 kms-’. This estimate is very close to the value found by Dziewonski and Gilbert (1971) from an analysis of other modes sensitive to IC properties. The low shear velocity results in a high Poisson’s ratio (- 0.45) for IC material and it has been suggested that this is indicative of a material near its melting point. The high value of CJ in the IC of many Earth models has often been used to argue that it cannot be a crystalline solid. However Al’tshuler and Sharip-
55
General Physical Properties of the Earth
dzhanov (1971) have reported shock wave measurements of 0 for copper and iron up to pressures of 1 and 2 Mbar. They obtained values of 0.43 at about 2 Mbar and the data extrapolate smoothly to the value found for the IC. Unlike other elastic properties, 0 increases with both temperature and pressure, although some metals have extremely high values of 0 even at low temperatures and pressures (Simmons and Wang, 1971). Falzone and Stacey (1980) have shown that it is not merely normal but necessary that 0 should be very high in any crystal at very high pressures. They point out that terms in conventional elasticity theory that are normally neglected become important when the ambient pressure is not negligible in comparison with the elastic moduli. These terms give a pressure dependence to the elastic moduli in addition to that resulting from the pressure dependence of atomic forces. The net effect is to reduce the modulus of rigidity and to increase the incompressibility, resulting in an increase in 0 (see (1.13)). The high value of 0 implies a state which allows large lateral contraction compared with longitudinal extension, suggesting a soft solid that is perhaps near its melting point. Under these conditions some variation of physical properties throughout the IC might be expected. The viscosity of the Earth's core is one of the least known physical parameters of the Earth. Estimates in the literature of the kinematic viscosity v differ by many orders of magnitude, ranging from to 10" cm2 s-'. High values of the viscosity have been deduced from the observation that compressional waves traverse the core without suffering appreciable attenuation (see e.g. Rochester, 1970). Such results lead to a value of v of the order of 109-f011 cm2 s-'. Gans (1972a) has shown that the effect of the Earth's magnetic field at the MCB cannot reconcile seismic data for S H waves with a very low viscosity. However, he offered the very interesting speculation that a highly 10" c m2 s -l could viscous region 5 10km thick at the MCB with v satisfy the seismic data and still permit a very low value of the viscosity in the OC as a whole. Hide (1971) has estimated the value of v at the MCB. He argued that if "bumps" on the boundary strongly influence the flow in the core, as suggested by himself and Malin (see §4.7), their height must exceed the viscous boundary layer thickness by a certain factor. Using the estimate for the height of these bumps given by himself and Horai (1968), he obtained an upper limit for the effective kinematic viscosity (i.e. eddy plus molecular) at the MCB of 1o6cm2s-'. Gans (1972b) has estimated the value of v at the ICB, assuming that this boundary is a melting transition and using Andrade's formula for the viscosity of a substance at its melting point. The estimates for pure iron give
-
-
9.0 x
< v < 1.7
x
10-2cm2s-'
56
The Earth’s Core
The core, however, is not pure iron, but contains some 10% lighter alloying element-silicon, oxygen and sulphur have been proposed (see $5.7). Both substances would lower the liquidus temperature, density and average atomic weight. The experimental data on the effect of alloying on the viscosity, however, are very sparse, although it seems probable that it would be lowered. It is not possible to estimate with any certainty the amount of the decrease. Gans suggests that in the core 2.8 x
< v < 1.5 x lo-’ cm2 s - ’
with a typical value of 6 x cm2 s-’. This range of values applies at the ICB. However if the melting point gradient is very shallow throughout the core (see $3.4), this range will not change much. With these values, the precessional mechanism proposed by Malkus (1968) to generate the Earth’s magnetic field (see $4.6) would be unstable. Whether it would be sufficiently unstable to overcome a highly sub-adiabatic temperature gradient in the core as proposed by Higgins and Kennedy (1971) cannot be determined. Crossley and Smylie (1975) have considered in detail the rate at which energy is dissipated in the liquid OC of the Earth. There are two possible dissipative mechanisms, ohmic and viscous, and they showed that oscillations in the core are virtually unaffected by either damping mechanism. Most of the ohmic dissipation takes place within a few “skin-depths’’ of the boundariesCrossley and Smylie expect that a similar result would be obtained for viscous dissipation, although their calculations were confined to estimating laminar dissipation in the body of the liquid core. The conclusion that the Earth’s core appears to be nearly free of dissipation for small harmonic oscillations, such as those which occur in the natural elastic oscillations of the Earth or those which may occur as gravitational oscillations if the temperature profile in the core is subadiabatic (see 991.4 and 3.6), suggests that modes of oscillation that are largely confined to the core may persist for unexpectedly long times-perhaps long enough to be important in driving the geodynamo (see $4.6). The viscosity of the lower mantle is discussed in $3.8.
1.7 Models of the Earth‘s Interior
The mathematical formulation of the inverse problem in geophysics characterizes possible variations of physical parameters as entities in an abstract function space, each entity representing an Earth model. In particular, a spherically symmetric, non-rotating, linearly elastic, isotropic Earth can be
General Physical Properties of the Earth
57
described by specifying the compressional velocity, the shear velocity, and the density as functions of the radius. An observation is the value of a functional defined in this space of Earth models+xamples are the Earth’s mass, moment of inertia, the measured travel-times of seismic waves, and the observed periods of free oscillation. Since the distributions of physical parameters are continuous in some interval and the number of data obtainable is necessarily finite, the inverse problem generally has no unique solution. Furthermore, the observations used as data are invariably contaminated by errors; only estimates of the values of data functionals for the Earth are available. A general discussion of the inverse problem in geophysics has been given in a series of papers by Backus and Gilbert. They investigated (1967) the extent to which a finite set of data functionals (called by them gross Earth data) can be used to determine the Earth’s internal structure. In a later paper (1968) they showed how to determine the shortest length-scale the given data can resolve at any particular depth. The principal result of their work is that it is possible to draw rigorous conclusions about the internal structure of the Earth from a finite set of gross Earth data. Infinite resolution can never be achieved, yet rigorous answers can nevertheless be given to a number of qualitative questions, such as whether there are low-velocity zones or density inversions in the mantle. In these first two papers, observational errors were neglected. In a later paper, Backus and Gilbert (1970) considered the effect of such errors and investigated the inversion of a finite set G of inaccurate gross Earth data-they showed that from some sets G it is possible to determine the structure of the Earth (except for fine-scale detail) within certain limits of error. They also showed how to determine whether a given set G will permit the construction of such localized averages of Earth structure, and how to find the shortest length-scale over which G gives a local average structure at a given depth if the variance of the error is to be less than a given amount. Detailed accounts of their work have been given by Backus (1971) and Parker (1970,1972a). In practice all data will be subject to some error, so that there are two measures of imprecision (an error of the estimate and its resolution) both of which one would like to make as small as possible. It is not possible, however, to minimize both at once. The error estimate of a property can be improved, but only at the expense of the resolving power and vice versa. Thus there exists a tradeoff between error and resolution at every radius, and some compromise must be made in choosing the best model. Parker (1972b) has also considered the inverse problem with grossly inadequate data. Such is the case, not only when the number of observations is small, but also if the inverse problem is intrinsically non-unique as is the case of attempting to determine the density inside a body from gravity obser-
58
The Earths Core
vations outside the body. Parker showed that although inadequate data cannot yield detailed structure, they can nevertheless be used to rule out certain classes of structures and provide bounds on acceptable models. The interpretation of inaccurate, insufficient and inconsistent data has also been investigated by Jackson (1972). The question of uniqueness has been further discussed by Dziewonski (1970) and the general linear inverse problem has been reviewed by Wiggins (1972). Finally, it must be emphasized that most inverse problems in geophysics are non-linear. In such cases Backus and Gilbert linearize the problem. Basically, their method employs an iterative perturbation algorithm that approximates the difference between the sought representation of the Earth and some initial model as a particular solution to the finite system of linear, inhomogeneous, integral equations relating changes in the data. The data functionals are computed for the starting model and subtracted from the observed data; the system of perturbation equations is solved, and the calculated perturbation added to the starting model. This process is iterated until the data are satisfied. Because the inverse problem is non-linear and has no unique solution, interpretation of any numerical results needs special care. A common mistake is to infer that because a certain model satisfies the data, some feature of that model actually exists in the Earth, when in reality the data do not require this feature. Moreover there is no guarantee that other starting models do not exist which are outside the scope of a linear description. Wiggins et al. (1973) have shown that body wave behaviour is too strongly non-linear for linearized schemes to be effective in predicting uncertainties. McMechan and Wiggins (1972) have developed a direct method for inverting seismic travel-time (T,A) data to determine velocity-depth profiles. They showed how a set of data points in the ( T , A ) plane, with estimates of the uncertainties, may be converted into an equivalent envelope in the velocitydepth plane. They refer to the problem of finding such envelopes of all possible models consistent with the observations as “extremal inversion”. They believe that the extremal inversion technique makes the usual Monte Carlo inversion method obsolete. In a later paper, Wiggins et al. (1973) examined the range of Earth structures that can be obtained from a set of body wave observations. Figure 1.16 shows the envelope of all possible models consistent with the set of data they used. In particular they found that there is an uncertainty of f 4 0 km in the radius of the ICB and f 18 km at the MCB. The velocity uncertainty is about f0.08 km s-’ for P and S waves in the lower mantle and about kO.10 km s-’ in the core. An interesting result of their investigation is that quite crude observations of SKKS-SKS traveltimes restrict the range of possible models far more than do the most precise estimates of PnKP travel-times.
..
c
'm lo-
**+**
E
Fixed crust" Fixed upper mantle
Y
v
,9
L .-
x
I
3
@
-
76-
5-
6!500
6000
5500
5ooo
4500
4000
: Radius (km
Fig. 1.16. Envelopes of all possible models of Earth structure from a given set of body wave observations. The envelope for the core was found under the assumption of 8 fixed core radius uf 3481 km. The heavy middle line is the standard model. (After Wiggins et a / . ,1973.)
60
The Earth's Core
The basic concept in the theory of Backus and Gilbert is that, although the exact solution cannot be computed because the information provided by the data is insufficient, it is possible to estimate accurately linear averages of the desired model. The aim of their theory is the construction of an optimal inverse filter from the constraints imposed by the observations, through which the correct solution may be viewed. As already mentioned, there is a tradeoff between the ability to resolve detail and the accuracy with which this detail can be estimated. Jordan (1972) has used a variation of the Backus-Gilbert theory incorporating the stochastic inverse theory of Franklin (1970). A particular, unique solution to the linear system is obtained by minimizing a specified quadratic measure of error. This quadratic form is the sum of two terms, a measure of the resolution of the estimate and a measure of its accuracy, parameterized to yield a Backus-Gilbert-type tradeoff curve. Jordan showed that the generalized inverse of Penrose (1955) and Moore (1920) and the stochastic inverse of Franklin (1970) lie on this tradeoff curve, the stochastic inverse being, in one sense, an optimal point. Any particular solution computed by selecting a point on the tradeoff curve is shown to be an estimate of the correct solution convolved with a projection-like smoothing operator. Dziewonski and Gilbert (1973a) observed an IC mode (llSz) in 11 spectra of seismograms with large lag times-over two days after the origin time in some cases (see Fig. 1.17). This represents direct proof of the solidity of the
r
Period ( s 1 Fig. 1.17. Histograms of a number of spectral peaks read from the spectra of vertical component readings. The histogram for seismograms with a lag-time of less than 18 h, broken line; over 18 h, solid line. (After Dziewonski and Gilbert, 1973a.)
General Physical Properties of the Earth
61
IC-the mode lSz could not exist if the IC were liquid. The IC mode lSz is coupled with a compressional mode of nearly identical phase velocity (loSz)-the observed periods are 246.89 s and 247.74 s respectively. The coincidence of loSzand llSz implies that the average shear velocity in the IC must be 3.6 km s - l , and that dissipation in the IC is low. Because of the large wavelengths of the normal modes, their eigenfrequencies are likely to be more closely related to the properties of a spherically symmetric, radially stratified “average” Earth than the nearly exclusive land-based travel-time observations. The resolving power of the normal mode data set shows that the average velocities and densities are known in the mantle to 1% for averaging lengths of -200 km (Gilbert et al., 1973). For the same precision the averaging lengths in the OC are -400 km. The structure of the region D” has been discussed in 51.3. There is no question about the sharpness of the MCB, although there may be minor lateral variations in some of the physical properties there. Dziewonski and Haddon (1974) have reviewed all data on the radius rc of the core. The first close estimate was made by Gutenberg (1913), who obtained a value of 3471 km from a determination of the distance at which P waves become diffracted. Much later, Jeffreys (1939a) proposed a method using the travel-times of core reflections and obtained a value of 3473 ( f 4.2) km, which he revised later (1939b) to 3473.1 (k2.5) km. His method (with some modifications) is still being used and it is only in recent years that additional data have forced revision of his estimate. Using travel-times of PcP phases from nuclear explosions, Taggart and Engdahl (1968) obtained a value of 3477 (k2.0) km for rc. Bolt (1972) inferred a 2% decrease in V , through the lowest 150 km of the mantle leading to a value for rc of 3475 (k2.0) km. Hales and Roberts (1970) obtained values of I , of 3490 (f4.7) km and 3486 (k4.6) km for two possible mantle models, basing their calculations on the differences in travel-times between ScS and S in the distance range 48” < A < 70”. Engdahl and Johnson (1972) analysed the differential travel-times Pep-P from three nuclear explosions in the Aleutian Islands and concluded that yC should be increased by 5-15 km over the value of 3477 km obtained by Taggart and Engdahl(l968). Their preferred estimation is 3482.2 ( 2.9) km. The free oscillation data demanded an increase in I , over earlier estimates. Dorman et al. (1965) proposed a model in which r, was increased by 10 km and a “soft” layer introduced at the base of the mantle. Haddon and Bullen (1969) showed that the travel-time and free oscillation data could be reconciled with an Adams-Williamson density gradient (see 51.6) in the lower mantle by increasing r, by 15-20 km over Jeffreys’ (1939b) value of 3473 km. Press used a Monte Carlo method to generate a large number of Earth models (see 51.6). The successful models (1970b) did not show a strong prefer-
-
62
The Earths Core
ence for any particular value of the core radius within the bounds from 3463 to 3483 km. Dziewonski (1970) showed that only additional overtone data could narrow the range of permissible solutions based on fundamental mode data alone. Using the eigenperiods of 70 spheroidal and toroidal overtones from the spectra of 84 recordings of the Alaska earthquake of March 28, 1964 (identified and measured by Dziewonski and Gilbert, 1972), he was able to narrow the range of r, to 3486-3491 km. Many more overtone data have now been obtained (Dziewonski and Gilbert, 1973b) and have been used by a number of authors in constructing Earth models. Jordan and Anderson (1974) obtained a value for r, of 3845 km and Gilbert et al. (1973) values of 3482.6 and 3484.9 km for two different models. Engdahl and Johnson (1974) using differential P C P travel-times, obtained values in the range 34843486 km. The best available estimate at present for I , is 3485 ( IfI 3) km. A radius of 1250 km postulated for the IC in the Jeffreys-Bullen model now appears to be somewhat too great. Bolt’s (1962) model used a radius of 1216 km and later work by Bolt (1964) supported by wide-angle reflections of P K i K P (Bolt et al., 1968) gave values near 1220 km. The models of Buchbinder (1971) and Qamar (1973) incorporate IC radii of 1226 and 1213 km respectively. Engdahl et al. (1974) have estimated the radius of the IC from differential P K i K P (i.e. P K i K P minus PcP) arrival time data for a number of different Earth models. The data indicate an IC radius in the range 12201230 km. For a model incorporating a decreased velocity gradient just above the ICB, their preferred value for the radius of the IC is 1227.4 & 0.6 km. Comparison of pulse shapes and pulse durations for P , PcP and P K i K P phases indicates that the ICB is very sharp. A value in the range 12151235 km is now preferred. Bolt and Urhammer (1975) carried out least-squares iterations with penalty functions on Earth model CAL5* based on observations of eigenvibrations, surface waves and body waves. In the penalty function method, linear equality constraints are weighted so that the least-squares estimator suffers a specified penalty for progressive violation of the physical restrictions. They also derived a procedure for calculating the trade-off between spread and variance for density estimates, and then assessed the resolvability of density and index of homogeneity at a number of levels in the Earth. The density in the lower mantle in their final model is a little closer to homogeneous, adiabatic conditions. Density values are about 0.15 g cm-3 less than those of B1 (Jordan and Anderson, 1974) in the region 20W2500 km. As a consequence, density values in the core are significantly greater than those of
* Details of these earlier models will not be given-they required.
can be found in the references if
63
General Physical Properties of the Earth
-
B1 (the mean density at the bottom of the OC is 1 2 . 3 4 g ~ m -compared ~ with 12.11 g ~ m -in ~ Model Bl). In the IC, V , N 3.55 kms,-l, p N 13.30g cm-3 and Poisson's ratio ~ 0 . 4 5 . Hales et al. (1974) suggested the construction of a spherically symmetric Earth model in which the radial variations of seismic parameters are expressed by piece-wise continuous analytical functions such as low-order polynomials in the radius. This idea was taken up by Dziewonski et al. (1975) who used polynomials of order not higher than three to construct a parametric Earth model (PEM). Their starting model was based on model 1066B (Gilbert and Dziewonski, 1975) with some modifications. The data used in the inversion consisted of observations of eigenperiods for 1064 normal modes, 246 travel-times of body waves for five different phases and regional surface-wave dispersion data. They presented three Earth models, all identical below a depth of 420 km; models P E M - 0 and PEM-C reflecting the different properties of the oceanic and continental upper mantles and model PEM-A representing an average Earth. The densities and velocities in the lower mantle (depths greater than 670 km) and core are consistent with the Adams-Williamson equation to less than 0.2%. Thus, any departures from homogeneity and adiabaticity within these regions must be very small. Dziewonski et al. (1975) also showed that the velocities in the lower mantle were consistent with the complete first-order finite-strain theory to within 0.2% for V p and 0.4% for Vs. In the IC, Vs varies from 3.44 to 3.56 km s-', confirming the earlier estimate of 3.5 km s-' by Dziewonski and Gilbert (1971). Buchbinder (1976) computed PcP and PmKP travel times for three simple or parametric Earth models based on free oscillation and travel-time dataH B , (Haddon and Bullen, 1969), B1 (Jordan and Anderson, 1974) and PEMA (Dziewonski et al., 1975)-and compared them with PCP and PmKP travel-times from different sources. The comparison was made only for the region above and below the MCB. He found that only model B1 does not need a correction for its PcP travel-times. For the PmKP travel-times all three models needed corrections. Normal-mode data are not adequate to resolve details of Earth structure having wavelengths of the order of 1 W 2 0 0 km. To resolve these features, body wave data, which are of higher resolving power, must be used. Such data are by their nature more path-dependent than normal modes-the role of free oscillations is to determine differences between the average Earth and the more path-specific body wave structures. Anderson and Hart (1976) thus used a starting model based on high-resolution body wave data and perturbed it to fit the normal mode data set. The resulting model retains the features found by body wave studies, but the average properties are suitably adjusted to correspond to average Earth properties, as is required by the nor-
64
The Earths Core
4000
3000
2000
1000
0
Radius (km) Fig. 1.18. A comparison of densities p and seismic velocities Vp and V, estimated in three Earth models, CALG, PEM and QM2. (After Bolt and Uhrhammer 1981 .)
ma1 mode data set. Their final model (C2) shows slight inhomogeneity at the base of the mantle, the top of the core and the regions on both sides of the ICB. Both the V p and density jump at the ICB are small. Hart et al. (1977) later examined the effect of correcting Earth model C2 for attenuation. The result was generally to increase seismic velocities, particularly shear velocities, throughout the model. The largest increases occur in those regions where Q is lowest. In spite of recent refinements, the resolution of P and S velocity gradients places considerable limitations on the sharpness of inferences that can be drawn about dynamical properties, density stratification and deviations from adiabatic conditions. Recent core models have been based on limited sets of data on travel-times and amplitudes of seismic core waves, and measurements of the eigenfrequencies of the Earth. A comparison shows that the differences between independently constructed models such as CAL6 (Bolt and Urhammer, 1975), PEM (Dziewonski et al., 1975) and QM2 (Hart et al., 1977) are almost everywhere less than 1% (see Fig. 1.18). The differences depend on weighting and selections of data and on assumptions on smoothing. Figure 1.19 gives the distribution of the seismic parameter 4
6ot
50 4000
1
I
1
3Ooo
2000
Radius
Fig. 1 .IS.A comparison of the seismic parameter and Q M 2 . (After Bolt & Urhammer, 1981 .)
-0 -0
3
1
I
0
loo0
(km)
4 calculated from three Earth models, CALG, PEM,
-
-
2 -
-
v
c I
1
I
I
I
I
Fig. 1.20. The PREM model. Dashed lines are the horizontal components of velocity. Where q is 1 the model is isotropic. The core is isotropic. (After Dziewonski and Anderson, 1981 ).
TABLE 1.5 Earth model PREM and its funcrionals evaluated at a reference period of 1 s. Above 220 km the mantle is transversely isotropic;the parameters given are ”equivalent” isotropic moduli and velocities. (After Dziewonski and Anderson, 1981 .) Radius (km)
Depth (km)
Density (gcmP)
VP
v5
(kms-’)
(kms-’)
Q,
0. 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 900.0 1000.0 1 1 00.0 1200.0 1221.5 1221.5 1300.0 1400.0 1500.0 1600 0 1700.0 1800.0 1900.0 2000.0 21 00.0 2200.0 2300.0 2400.0 2500.0 2600.0
6371 0 6271 0 6171 0 6071 0 5971 0 5871 0 5771 0 5671 0 5571 0 5471 0 6371 0 5271 0 5171 0 5149 5 51 49 5 5071 0 4971 0 4871 0 4771 0 4671 0 4571 0 4471 0 4371 0 4271 0 4171 0 4071 0 3971 0 3871 0 3771 0
13.08848 13.08630 13.07977 13.06888 13.05364 13.03404 13.01009 12.98178 12.94912 12-3121 1 12.87073 12.82501 12.77493 12.76360 12.16634 12.12500 12.06924 12.00989 11.94682 11.87990 1 1 -80900 11.73401 11.65478 1 1 -57119 1 1 -48311 11.39042 1 1 29298 11,19067 11.08335
11.26220 11.26064 11.25593 11.24809 11.23712 11.22301 11.20576 11,18538 1 1 ,I6186 11,13521 1 1.1 0542 11.07249 11.03643 1 1.02827 10.35568 10.30971 10.24959 10.18743 10.12291 10.05572 9.98554 9.91206 9.83496 9.75393 9.66865 9.57881 9.48409 9.38418 9.27876
3.66780 3.66670 3.66342 3.65794 3.65027 3.64041 3.62835 3.61411
85 85 85 85
3.59767 3.57905 3.55823 3.53522 3.51002 3.50432
0. 0.
0. 0. 0. 0. 0.
0. 0. 0. 0. 0.
0. 0. 0.
0
328 328 328 328 328 328 328 1328 1328 1328 1328 1328 1328 1328 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822
0
57822
85 85 a5
85 a5 85
85 a5 85 85
0 0 0 0 0 0 0 0 0 0 0 0
0
108.90 108.88 108.80 108.68 108.51 108.29 108.02 107 70 107.33 106.91 106.45 105.94 105.38 105.25 107.24 106.29 105.05 103.78 102.47 101.12 99.71 98.25 96.73 95.14 93.48 91 7 5 89.95 88 06 86.10
ti
P
(kbar)
(kbar)
14253 14248 14231 14203 14164 14114 14053 13981 13898 13805 13701 13586 13462 13434 13047 12888 12679 12464 12242 1201 3 1 1 775 1 1 529 1 1 273 1 1009 10735 10451 101 58 9855 9542
1761 1759 1755 1749 1739 1727 1713 1696 1676 1654 1630 1603 1574 1567
0 0 0 0 0 0 0
0 0 0
0 0 0
0 0
IS
0.4407 0.4407 0.4408 0.4409 0.4410 0.4412 0.4414 0.6417 0.4420 0.4424 0.4428 0.4432 0.4437 0.4438 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000 0.5000
Gravity
Pressure (kbar)
dkldp
3638.524 3636.131 3628.956 361 7.011 3600.315 3578.894 3552.783 3522.024 3486.665 3446.764 3402.383 3353.596 3300.480 3288.513 3288.502 3245.423 31 87.493 31 26.159 3061.461 2993.457 2922.221 2847.839 2770.407 2690.035 2606.838 2520.942 2432.484 2341.603 2248.453
2 3360 2 3363 2 3365 2 3369 2 3375 2 3382 2 3391 2 3402 23414 2 3428 2 3443 2 3460 2 3480 2 3486 3 7545 3 6539 3 5478 3 4649 3 401 7 3 3552 3 3230 3 3028 3 2927 3 291 1 3 2966 3 3080 3 3242 3 3441 3 3670
(crnr-2)
0. 36.56 73.11 109.61 146.04 182.39 21 8.62 254.73 290.68 326.45 362.03 397.39 432.51 440.02 440.03 463.68 494.13 524.77 555.48 586.14 61 6.69 647.04 677.15 706.57 736.45 765.56 794.25 822.48 850.23
2700 0 2800 0 2900 0 3000 0 31000 3200 0 3300 0 3400 0 3480 0 3480 0 3500 0 3600 0 3630 0 3630 0 3700 0 3800 0 3900 0 4000 0 4100 0 4200 0 4300 0 4400 0 4500 0 4600 0 4700 0 4800 0 4900 0 5000 0 51 00 0 5200 0 5300 0 5400 0 5500 0 5600 0
3671 .O 3571 .O 3471 .O 3371 .O 3271 .O 31 71 .O 3071 .O 2971 .O 2891 .O 2891 .O 2871 .O 2771 .O 2741 .O 2741 .O 2671 .O 2571 .O 2471 .O 2371 .O 2271 .O 21 71 .O 2071 .0 1971 0 1871 .O 1771.O 1671 .O 1571 0 1471 .O 1371 .O 1271 .O 1171 0 1071 .O 971 .O 871 .O 771 0
10.97091 10.85321 10.73012 10.60152 10.46727 10.32726 10.181 34 10.02940 9 90349 5.56645 5.55641 5.50642 5.49145 5.49145 5.45657 5.40681 5.35706 5.30724 5.25729 5.20713 5 15669 5.10590 5.05469 5.00299 4.95073 4.89783 4.84422 4.78983 4.73160 4.67844 4.62129 4.56307 4.50372 4.44317
9.16752 9.05015 8.92632 8.79573 8.65805 8.51298 8.36019 8.19939 8.06482 13.71660 13.71168 13.68753 13.68041 13.68041 13.59597 13.47742 13 36074 13.24532 13.13055 13.01579 12.90045 12.78389 12.66550 12.54466 12.42075 12.29316 12.161 26 12.02445 11.88209 11.73357 11.57828 11.41560 11.24490 11.06557
0 0
0 0 0 0
0 0
0 726466 726486 726575 7 26597 7 26597 723403 718892 714423 709974 705525 701053 696538 691957 687289 682512 6 77606 672548 667317 661891 656250 650370 644232 637813 6 31091 624046
0
0 0 0
0 0 0
0 0
312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312 312
57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 !m22 57822 57822 57822 57822 57822 57822 57822 57822 57822
84 04 81 91 79 68 77 36 74 96 ?2 47 69 89 67 23 65 04 17 78 17 64 16 96 16 76 16 76 1508 11273 11046 708 23 10604 103 88 101 73 99 59 97 43 95 26 93 06 90 81 88 52 86 17 83 76 81 28 78 72 76 08 73 34 70 52
9220 8889 8550 8202 7846 7484 7116 6743 6441 6556 6537 6440 641 2 641 2 6279 6095 591 7 5744 5575 5409 5246 5085 4925 4766 4607 4448 4288 41 za 3966 3803 3638 3471 3303 31 33
0 05000 0 05000 0 05000 0 05000 0 05000 0 05000 0 05000 0 05000 0 05000 2938 03051 2933 03049 2907 03038 2899 03035 2899 03035 2855 03026 2794 03012 2734 02998 2675 02984 2617 02971 2559 02957 2502 0 2943 2445 02928 2388 02913 2331 02898 2273 02881 2215 02864 2157 02846 2098 02826 2039 02805 1979 02183 1918 02758 1856 02731 1794 02701 1730 02668
21 53 189 2055 978 1956.991 1856.409 1754418 1651.209 1546.982 441 941 357 51 0 357 509 345 61 9 287 067 269 742 269 741 229 71 9 1173 465 1 1 18 207 1063 864 101 0 363 957 641 905 646 854 332 803 660 753 598 704 119 655 202 606 830 558 991 511 676 464 882 41 8 606 372 852 321 673 282 928
33919 3 41a0 3 4448 3 471 4 3 4972 3 5215 3 5437 3 5629 3 5769 16435 7 6434 16424 16420 3 3344 3 2957 3 2443 3 2029 31716 3 1503 3 1393 3 1383 3 1472 3 1657 3 1935 3 2302 3 2750 3 3276 3 3871 3 4527 3 5236 3 5989 3 6775 3 7582 3 8403
877 46 904 14 930 23 955 70 980 51 1004 64 1028 04 1050 65 1068 23 1068 23 1065 32 1052 04 1048 44 1048 44 1040 66 1030 95 1022 72 1015 80 101006 1005 35 1001 56 998 59 996 35 994 74 993 69 993 14 993 01 993 26 993 83 994 67 995 73 996 98 998 36 999 85
T A B L E l . 5 continued overleaf
TABLE 1.5-contmued
5600 0 5650 0 5701 0 5701 0 5736 0 5771 0 5771 0 5821 0 5871 0 5921 0 5971 0 59Ji 0 60160 6061 0 6106 0 6151 0 6151 0 6186 0 6221 0 6256 0 6291 0 6291 0 631 1 0 6331 0 6346 6 6346 6 6356 0 6356 0 6368 0 6368 o 6371 0
771 0 721 0 670 0 670 0 635 0 600 0 600 0 550 0 500 0 450 0 400 0 400 0 355 0 3100 265 0 220 0 220 0 1850 1500 1150 80 0 80 0 60 0 40 0 24 4 24 4 150 150 30 30 0
4 4431 6 4 41 241 4 38071 3 9921 4 3 98399 3 97584 3 97584 3 91 282 3 84980 3 78678 3 72378 3 54325 3 51 639 3 48951 3 46264 3 43578 3 35950 3 36330 3 36710 3 37091 3 37471 3 37471 3 37688 3 37906 3 38076 2 90000 2 90000 2 60000 2 60000 102000 102M)o
VP
vs
(kms-')
(kms-')
11 06556
6 24046 6 0941 8 5 94508 5 57020 5 5431 1 5 51 602 5 51 600 5 3701 4 5 22428 5 07842 4 93259 4 76989 4 73840 4 70690 4 67540 4 64391 4 41 885 4 431 08 4 44361 4 45643 4 46953 4 46954 4 4771 5 4 48486 4 49094 3 90000 3 90000 3 20000 3 20000
10 91 005
I075131 10 26622 10 21 203 10 15782 10 15782 9 901 85 9 64588 9 38990 9 13397 8 90522 8 81 867 8 73209 8 64552 a 55896 7 98970 801180 8 03370 8 0554Q 8 07688 8 07689 8 08907 810119 811061 6 80000 6 80000 5 80000 5 80000 145000 145000
0 0
# QP
31 2 31 2 31 2 143 t 43 143 143 143 143 143 143 143 143 143 143 143 80 80 80 80 80 600 600 600 600 600 600
600 600 0 0
QA
57822 57822 57822 57822 57822 57822 57822 578.22 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822 57822
L:
( k m 2 K z ) (kbar)
70.52 69.51 68.47 64.03 63.32 62.61 62.61 59.60 56.65 53.78 50.99 48.97 47.83 46.71 45.60 44.50 37.80 38.01 38.21 38.41 38.60 38.60 38.71 38.81 38.89 25 96 25.96 i9.99 19.99 210 2.10
P
(kbar)
u
21
02668 02732 02798 02914 02911 02909 02909 02917 02924 02933 02942 02988 02971 02952 02933 0 2914 02797 0.2797 0.2796 02795 02793 02793 02792 02790 02789 02549 02549 02812 02812 0 05000
21
0 05000
31 33 3067 2999 2556 2523 2489 2489 2332 21 81 2037 1899 1735 1682 1630 1579 1529 1270 1278 1287 1295 1303 1303 1307 1311 1315 753 753 520 520
1730 1639 1548 1239 1224 1210 1210 1128 1051 977 906 806 790 773 757 741 656 660 665 669 674 674 677 680 682 441 441 266 266
Pressure (kbar)
282 927 260 783 238 342 238 334 224 364 21 0 426 21 0 425 190 703 171 311 152 251 133 527 133 520 117 702 102 027 86 497 71 115 71 108 59 466 47 824 36 183 24 546 24 539 17 891 1 1 239 6 043 6 040 3 370 3 364 0 303 0 299 -0 000
dk/dp
2 981 9 3 0086 3 0358 2 4000 2 3868 2 3734 8 091 0 7 8833 7 6761 7 4695 7 2633 33718 3 3369 3 301 7 3 2662 3 2305 - 0 7364 - 0 7200 -0 7035 - 0 6868 - 0 6700 - 0 6700 - 0 6603 -0 6505 - 0 6428 - 0 0000 0 0000 0 0000 - 0 0000 - 0 0000
0 000
Gravity (ems-')
999 85 1000 63
1001 43 1001 43
1000 88 1000 38 1000 38 999 65 998 83 997 90 996 86 996 86 995 22 993 61 992 03 990 48 990 48 989 1 1 987 83 986 64 985 53 985 53 984 93 984 37 983 94 983 94 983 32 983 31 982 22 982 22 gal 56
General Physical Properties of the Earth
69
(equation 1.3) for the above three models and shows that the gradients of this parameter are not well-resolved. (It is the gradient of 4 that is important for solid state, temperature, compositional and convection studies.) Recent seismological evidence has favoured a simple two-layer core with a liquid OC, and a sharply-bounded solid IC. As discussed in 51.2, the hypothesis of a sharply-bounded transition region F has fallen from favour because of the explanation of precursors to P K I K P in terms of scattering sources near the MCB. Nevertheless, velocity jumps in F need be as small as only 0.01 km s-' to give rise to back-scattered waves with the observed amplitudes (Bolt and Urhammer, 1981). The P wave velocity distribution in the O C shows that the P velocity between 1600km and about 1200km changes by only a few percent, i.e. there is near-independence of sound speed over a pressure change of 400 kbar. Thus, a region F between E and G does exist. The density distributions in E (see Fig. 1.18) determined from eigenvibration and travel-time inversions, without using the assumptions of Adams and Williamson, confirm a density gradient close to the Adams and Williamson value (at least, in the central part of E). The conclusion is that zero deviations from homogeneity and adiabaticity throughout most of E are sufficient but not necessary to satisfy the data. The largest differences in the estimates of density occur in the IC. However, both CAL6 and PEM have about the same jump in density (0.6 g cm-3) at the ICB. Models PEM and QM2 have essentially equal density distributions throughout the liquid OC. Observations of the amplitude of P K i K P and P K I I K P imply that there must be a sharp discontinuity in density, or in compressibility, or both, at the ICB. A jump in rigidity will not yield either of these reflections with the amplitudes observed. The central densities of CAL6, PEM and QM2 are 13.35, 13.01 and 12.57 g cm-3 respectively. In 1981 Dziewonski and Anderson published their Preliminary Earth Model (PREM) which they had presented at the 1979 IUGG General Assembly in Canberra. In order to satisfy the large amount of normal mode, surface wave and body wave data, they found it necessary to introduce anelastic dispersion and anisotropy for the mantle above 220 km. Their model is thus frequency-dependent. Like the earlier model PEM, PREM is parametric in nature, the various physical parameters being expressed as loworder polynomials in the radius, of order between zero and three in the various regions of the Earth. They used about 1000 normal mode periods, 500 summary travel-time observations and 100 normal mode Q values. This data set was supplemented with a special study of 12 years of ISC phase data which yielded an additional 1.75 x lo6 travel-time observations for P and S waves. To obtain reasonably good control over velocities in the OC, they com-
70
The Earths Core
bined data from four travel-time branches: S K K S , SKS, P K P ( A B ) and P K P ( B C ) . Differential travel-times, PCP - P (Engdahl and Johnson, 1974) and ScS- S (Jordan and Anderson, 1974) are important for the control of the radius of the OC. The P K i K P - PcP differential travel-times of Engdahl et al. (1974) give the best control of the radius of the IC. Their final model is shown in Fig. 1.20 and values of various physical parameters in Table 1.5. This table includes values of the parameter r] of Bullen (see (5.32)) which represents a measure of the deviation of a model from the Adams-Williamson equation (for which r] = 1). For the most part r] in the core and lower mantle is very close to unity, the small deviations, in some cases, being an artifact of the polynomial representation. In the lower 150 km of the mantle (region D”), the velocity is nearly constant; the radius of the OC is 3480 km. Dziewonski and Anderson suggest that the core radius may be 1.7 km larger, which would satisfy the observations that slower velocities may exist in D”.
References
Adams, R. D. (1972). Multiple inner core reflections from a Novaya Zemlya explosion. Bull. Seism. SOC.Amer. 62, 1063. Adams, R. D. and Randall, M. J. (1963). Observed triplication of PKP. Nature 200,744. Adams, R. D. and Randall, M. J., (1964). The fine structure of the Earth’s core. Bull. Seism. Soc. Amer. 54, 1299. Akopyan, S. Ts., Zharkov, V. N. and Lyubimov, V. M. (1975). The dynamic shear modulus in the interior of the Earth. Dokl. Earth Sci. Ser. 223, 1. Akopyan, S. Ts., Zharkov, V. N. and Lyubimov, V. M. (1976). Corrections to the eigenfrequencies of the Earth due to the dynamic shear modulus. Izo. Acad. Sci. U S S R Phys. Solid Earth 12,625. Alder, A. J. and Trigueros, M. (1977). Suggestion of a eutectic region between the liquid and solid core of the Earth. J . Geophys Res. 82,2535. Alterman, Z., Jarosch H. and Pekeris, C. L. (1959). Oscillations of the Earth. Proc. Roy. SOC. London A252,80. Al’tshuler, L. and Sharipdzhanov, L. (1971). Distribution of iron in the Earth and its chemical differentiations. Izv. Acad. Sci. USSR. Phys. Solid Earth 4 3 . Anderson, D. L. (1967). A seismic equation of state. Geophys. J . 13,9. Anderson, D. L. and Hanks, T. C. (1972). Formation of the Earth’s core. Nature 237,387. Anderson, D. L. and Hart, R. S. (1976). An Earth model based on free oscillations and body waves. J . Geophys. Rex 81, 1461. Anderson, D. L. and Hart, R. S. (1978a). Attenuation models of the Earth. Phys. Earth Planet. Int. 16, 289. Anderson, D. L. and Hart, R. S.(1978b). Q of the Earth. J . Geophys. Res. 83,5869. Anderson, D. L., Ben-Menahem, A. and Archambeau, C. B. (1965). Attenuation of seismic energy in the upper mantle. J . Geophys. Res. 70,505. Anderson, 0. L. (1973). Comments on the power law representation of Birch’s law. J . Geophys. Res. 78,4901. Anderssen, R. S. and Seneta, E. (1971). A simple statistical estimation procedure for Monte Carlo inversion in geophysics. Pure Appl. Geophys. 91,5014.
General Physical Properties of the €arrh
71
Anderssen, R. S. and Seneta, E. (1972). A simple statistical estimation procedure for Monte Carlo inversion in geophysics. 11: Efficiency and Hempel's paradox. Pure Appl. Geophys. 96, 5. Anderssen, R. S., Worthington, M. H. and Cleary, J. R. (1972). Density modelling by Monte Carlo inversion. I: Methodology. Geophys. J . 29,433. Backus, G. (1971). Inference from inadequate and inaccurate data. In Mathematical Problems in the Geophysical Sciences (W. H. Reid, ed.). Lectures in Applied Mathematics, Vol. 14, Amer. Math. SOC. Backus, G. E. and Gilbert, J. F. (1961). The rotational splitting of the free oscillations of tfie Earth. Proc. Nat. Acad. Sci. U S A 47, 362. Backus, G. E. and Gilbert, J. F. (1967). Numerical applications of a formalism for geophysical inverse problems. Geophys. J . 13,247. Backus, G. E. and Gilbert, J. F. (1968). The resolving power of gross Earth data. Geophys. J . 16, 169. Backus, G. and Gilbert F. (1970). Uniqueness in the inversion of inaccurate gross Earth data. Ehil. Trans. Roy. Soc. London A266, 123. Balakina, L. M. and Vvedenskaya, A. V. (1962). Izv. Akad. Nauk SSR. Ser. Geojiz 11,909. Bertrand, A. E. S. and Clowes, R. M. (1974). Seismic array evidence for a two-layer core transition zone. Phys. Earth Planet. Int. 8,251. Berzon, I. S., Kogan, S. D. and Pessechnik, I. P. (1972). The character of the mantle-core boundary from observations of PCP waves. Earth Planet. Sci. Lett. 16, 166. Berzon, I. S., Pessechnik, I. P. and Polikarpov, A. M. (1974). The determination of P wave attenuation values in the Earth's mantle. Geophys. J . 39,603. Birch, F. (1952). Elasticity and constitution of the Earth's interior. J . Geophys. Res. 57,227. Birch, F. (1960). The velocity of compressional waves in rocks to 10 kilobars, 1. J . Geophys. Res. 65, 1083. Birch, F. (1961a). The velocity ofcompressional waves in rocks to 10 kilobars, 2. J . Geophys. Res. 66,2199. Birch, F. (1961b). Composition of the Earth's mantle. Geophys. J . 4,295. Birch, F. (1964). Density and composition of mantle and core. J . Geophys. Res. 69,4377. Bolt, B. A. (1959). Travel times of PKP up to 145".Geophys. J . 2,190. Bolt, B. A. (1962). Gutenberg's early PKP observations. Nature 196, 122. Bolt, B. A. (1964). The velocity of seismic waves near the Earth's centre. Bull. Seism. SOC.Amer. 54,191. Bolt, B. A. (1972). The density distribution near the base of the mantle and near the Earth's centre. Phys. Earth Planet. Int. 5,301. Bolt. B. A. (1977). The detection of PKIIKP and damping in the inner core. Ann. Geojis. 30,507. Bolt, B. A. and Canas, J. A. (1985). Constraints from core reflections on mantle Q and density at the core boundary. Phys. Earth Planet. Int. 38,l. Bolt, B. A. and Niazi, M. (1984). S velocities in D" from diffracted SH-waves at the core boundary. Geophys. J . 79,825. Bolt, B. A. and Qamar, A. (1970). Upper bound to the density jump at the boundary of the Earth's inner core. Nature 228, 148. Bolt, B. A. and Urhammer, R. (1975). Resolution techniques for density and heterogeneity in the Earth. Geophys. J . 42,419. Bolt, B. A. and Urhammer, R. (1981). The structure, density and homogeneity of the Earths core. In Evolution ofthe Earth (R. J. OConnell, W. S. Fyfe eds). Geodynamics Series Vol. 5, Amer. Geophys. Union. Bolt, B. A,, ONeill, M. and Qamar, A. (1968). Seismic waves near 110": is structure in core or upper mantle responsible? Geophys. J . 16,475.
72
The Earth’s Core
Bolt, B. A,, Niazi, M. and Somerville, M. (1970). Diffracted SCS and the shear velocity of the core boundary. Geophys. J . 19,299. Buchbinder, G. G. R. (1968). Properties of the core-mantle boundary and observations of PCP. J . Geophys. Res. 73,5901. Buchbinder, G. G. R. (1971). A velocity structure of the Earth’s core. Bull. Seism. Soc. Amer. 61, 429. Buchbinder, G. G. R. (1976). A test of new Earth models against PCP and PmKP travel times. Phys. Earth Planet. Int. 11,13. Buchbinder, G. G. R. and Poupinet, G. (1973). Problems related to PCP and the core-mantle boundary illustrated by two nuclear events. Bull. Seism. SOC.Amer. 63,2047. Buland, R. and Gilbert, F. (1978). Improved resolution of complex eigenfrequencies in analytically continued seismic spectra. Geophys. J . 52,457. Bullen, K. E. (1954). Seismology. Methuen, London. Bullen, K. E. (1963). An Introduction to the Theory of Seismology. Cambridge University Press, London. Bullen, K. E. (1965). Models for the density and elasticity of the Earths lower core. Geophys. J . 9, 233. Bullen, K. E. (1975). The Earths Density. Chapman and Hall. Bullen, K. E. and Haddon, R. A. W. (1970). Evidence from seismology and related sources on the Earth’s present internal structure. Phys. Earth Planet. Int. 2,342. Busse, F. H. (1974). On the free oscillations of the Earth’s inner core. J . Geophys. Res. 79,753. Caloi, P. (1961). Seismic waves from the outer core and the inner core. Geophys. J . 4,139. Canas, J. A. and Bolt, B. A. (1983). Nuevo metodo para la obtencion simultanea del factor medio de calidad especifica en el manto y litosfera terrestre y el salto de densidades en el limite. Nucleo-manto. Teoria Anales de Fisica Serie A 79, 57. Cathles, L. M. (1975). The oiscosity of the Earth’s mantle. Princeton University Press, Princeton, MA. Chang, A. C. and Cleary, J. R. (1978). Precursors to PKKP. Bull. Seism. Soc. Amer. 68,1059. Chang, A. C. and Cleary, J. R. (1981). Scattered P K K P further evidence for scattering at a rough core-mantle boundary. Phys. Earth Planet. Int. 24, 15. Chowdhury, D. K. and Frasier, C. W. (1973). Observations of PCP and P phases at LASA at distances from 26” to 40”. J . Geophys. Res. 78,6021. Choy, G. L. and Cormier, V. F. (1983). The structure of the inner core inferred from short-period and broadband GDSN data. Geophys. J . 7 2 , l . Christensen, N. I. (1966). Elasticity of some ultrabasic rocks. J . Geophys. Res. 71,5921. Christensen, U. (1984). Instability of a hot boundary layer and initiation of thermo-chemical plumes. Ann. Geophys. 2,311. Chung, D. H. (1974). General relationship among sound speeds. I: New experimental information. Phys. Earth Planet. Int. 8, 113. Clark, R. A. and Pearce, R. G. (1981). Comments on “Lateral heterogeneity at the base of the mantle revealed by observations of amplitudes of PKP phases” by I. S. Sacks, J. A. Snoke and L. Beach. Geophys. J . 66,741. Clark, S. P. Jr. and Ringwood, A. E. (1964). Density distribution and constitution of the mantle. Rev. Geophys. 2,35. Clark, S . P. Jr. and Turekian, K. K. (1979). Thermal constraints in the distribution of long-lived radioactive elements in the Earth. Phil. Trans. Roy. Soc. London A291,269. Cleary, J. R. (1969). The S-velocity at the core-mantle boundary from observations of diffracted S . Bull. Seism. Soc. Amer. 59, 1399. Cleary, J. R. (1974). The D region. Phys. Earth Planet. Int. 9, 13.
General Physical Properties of t.be Earth
73
Cleary, J. R. (1981). Seismic wave scattering on underside reflection at the core-mantle boundary. Phys. Earth Planet. Int. 26, 266. Cleary, J. R. and Haddon, R. A. W. (1972). Seismic wave scattering near the core-mantle boundary: a new interpretation of precursors to PKP. Nature 240, 549. Cook, A. H. (1963). The contribution of observations of satellites to the determination of the Earth’s gravitational potential. Space Sci. Rev. 2, 355. Cormier, V. F. (1981). Short-period P K P phases and the anelasticity mechanism of the inner core. Phys. Earth Planet. Int. 24,291. Cormier, V. F. and Richards, P. G. (1976). Comments on “The damping of core waves” by Anthony Qamar and Alfred0 Eisenberg. J . Geophys. Res. 81,3066. Crossley, D. J. (1975). Core undertones with rotation. Geophys. J . 42,477. Crossley, D. J. (1976). Reply to comments on “Core undertones with rotation” by M. L. Smith. Geophys. J . 44,729. Crossley, D. J. (1984). Oscillatory flow in the liquid core. Phys. Earth Planet. Int. 36, 1. Crossley, D. J. and Rochester, M. G. (1980). Simple core undertones. Geophys. J . 60, 129. Crossley, D. J. and Smylie, D. E. (1975). Electromagnctic and viscous damping of core oscillations. Geophys. J . 42, 1011. Dahlen, F. A. (1968). The normal modes of a rotating elliptical Earth. Geophys. J . 16,329. Dahlen, F. A. (1969). The normal modes of a rotating ellipical Earth-11: New resonance multiplet coupling. Geophys. J . 18,397. Dahlen, F. A. and Smith, F. L. (1975). The influence of rotation on the free oscillations of the Earth. Phil. Trans. R o y . Soc. London A279, 583. Denson, M. E. (1952). Longitudinal waves through the Earth’s core. Bull. Seism. Soc. Amer. 42, 119. Derr, J. S. (1969). Internal structure of the Earth inferred from free oscillations. J . Geophys. Res. 74, 5202. Doornbos, D. J. (1974). The anelasticity of the inner core. Geophys. J . 38,397. Doornbos, D. J. (1976). Characteristics of lower mantle inhomogeneities from scattered waves. Geophys. J . 44,447. [Correction 49,541 (1977).] Doornbos, D. J. (1978). On seismic wave-scattering by a rough, core-mantle boundary. Geophys. J . 53,643. Doornbos, D. J. (1980). The effect of a rough core-mantle boundary on PKKP. Phys. Earth Planet. Int. 21,351. Doornbos, D. J. (1981). The observable effect of wave interaction with a rough core-mantle boundary. Phys. Earth Planet. Int. 26,264. Doornbos, D. J. (1983). Present seismic evidence for a boundary layer at the base of the mantle. J . Geophys. Res. 88,3498. Doornbos, D. J. and Mondt, J. C. (1979a). Attenuation of P and S waves diffracted round the core. Geophys. J . 57,353. Doornbos, D. J. and Mondt, J. C. (1979b). P and S waves diffracted around the core and the velocity structure at the base of the mantle. Geophys. J . 57,381. Dorman, J., Ewing, J. and Alsop, L. (1965). Oscillations of the Earth: new core-mantle boundary model based on low-order free vibrations. Proc. N a t . Acad. Sci. U S A 54,364. Dziewonski, A. M. (1970). Correlation properties of free period partial derivatives and their relation to the resolution of gross Earth data. Bull. Seism. Soc. Amer. 60,741. Dziewonski, A. M. (1971). Overtones of free oscillations and the structure of the Earth’s interior. Science 172, 1336. Dziewonski, A. M. (1984). Mapping the lower mantle: determination of lateral heterogeneity in P velocity up to degree and order 6. J . Geophys. Res. 89,5929.
74
The Earths Core
Dziewonski, A. M. and Anderson, D. L. (1981). Preliminary reference Earth model. Phys. Earth Planet. Int. 25,297. Dziewonski, A. M. and Gilbert, F. (1971). Solidity of the inner core of the Earth inferred from normal mode observations. Nature 234,465. Dziewonski, A. M. and Gilbert, F. (1972). Observations of normal modes from 84 recordings of the Alaska earthquake of 1964, March 28. Geophys. J . 27,393. Dziewonski, A. M. and Gilbert, F. (1973a). Observations of normal modes from 84 recordings of the Alaska earthquake of 1964, March 28. 11: Further remarks based on new spheroidal overtone data. Geophys. J . 35,401. Dziewonski, A. M. and Gilbert, F. (1973b). Identification of normal modes using spectral stacking and stripping. Trans. Amer. Geophys. Union 54,374. Dziewonski, A. M. and Haddon, R. A. W. (1974). The radius of the core-mantle boundary inferred from travel-time and free oscillation data; a critical review. Phys. Earth Planet. Int. 9, 28. Dziewonski, A. M., Hales, A. L. and Lapwood, E. R. (1975). Parametrically simple Earth models consistent with geophysical data. Phys. Earth Planet. Int. 10, 12. Dziewonski, A. M., Hager, B. H. and OConnell, R. J. (1977). Large scale heterogeneities in the lower mantle. J . Geophys. Res. 82,239. Engdahl, E. R. (1968). Core phases and the Earth’s core. PhD Thesis, St. Louis University. Engdahl, E. R. and Johnson, L. E. (1972). A new PCP data set from nuclear explosions on Amchitka Island. Trans. Amer. Geophys. Union 53, 1045. Engdahl, E. R. and Johnson, L. E. (1974). Differential PCP travel times and the radius of the core. Geophys. J . 39,435. Engdahl, E. R., Flinn, E. A. and Romney, C. F. (1970). Seismic waves reflected from the Earth‘s inner core. Nature 228,852. Engdahl, E. R., Flinn, E. A. and Masse, R. P. (1974). Differential PKiKP travel times and the radius of the inner core. Geophys. J . 39,457. Ergin, K. (1967). Seismic evidence for a new layered structure of the Earth’s core. J . Geophys. Res. 72, 3669. Falzone, A. J. and Stacey, F. D. (1980). Second-order elasticity theory: explanation for the high Poissons’s ratio of the inner core. Phys. Earth Planet. Znt. 21,371. Fearn, D. R., Loper, D. E. and Roberts, P. H. (1981). Structure of the Earth’s inner core. Nature 292,232. Franklin, J. N. (1970). Well-posed stochastic extensions of ill-posed linear problems. J . Math. Analysis Applic. 31, 682. Friedlander, S . (1985). Internal oscillations in the Earth’s fluid core. Geophys. J . 80,345. Gans, R. F. (1972a). Reflection of SH in the presence of a magnetic field. Geophys. J . 29,173. Gans, R. F. (1972b). Viscosity of the Earth’s core. J . Geophys. Res. 77,360. Gilbert, F. and Dziewonski, A. M. (1975). An application of normal mode theory to the retrieval of structural parameters and source mechanisms for seismic spectra. Phil. Trans. Roy. SOC. London A278,187. Gilbert, F. and Helmberger, D. (1972). Generalized ray theory for a layered sphere. Geophys. J . 27,57. Gilbert, F., Dziewonski, A. M. and Brune, J. (1973). An informative solution to a seismological inverse problem. Proc. Nat. Acad. Sci. U S A 70, 1410. Greenspan, H. P. (1968). The Theory ofRotating Fluids. Cambridge University Press, London. Gutenberg, B. (1913). Uber die Konstitution des Erdinnern, erschlossen aus Erdbebenbeobachtungen. Phys. Z . 14,1217. Gutenberg, B. (1957). The “boundary” of the Earth’s inner core. Trans. Amer. Geophys. Union 38, 750. I
General Physical Properties of the €arth
75
Gutenberg, B. (1958a). Wave velocities in the Earth’s core. Bull. Seism. SOC.Amer. 48,301. Gutenberg, B. (1958b). Caustics produced by waves through the Earth’s core. Geophys. J . 1,238. Gutenberg, B. (1959). Physics of the Earth’s Interior. Academic Press, London and Orlando. Gutenberg, B. and Richter, C. F. (1938). P and the Earth’s core. Mon. Not. Roy. Astron. Soc. Geophys. Suppl. 4,363. Gutenberg, B. and Richter, C. F. (1939). On seismic waves. Gerl. Beit. Geophys. 54,94. Haddon, R. A. W. (1972). Corrugations on the mantle-core boundary or transition layers between inner and outer core? Trans. Amer. Geophys. Union. 53,600. Haddon, R. A. W. (1982). Evidence for inhomogeneities near the core-mantle boundary. Phil. Trans. Roy. SOC.London A306,61. Haddon, R. A. W. and Bullen, K. E. (1969). An Earth model incorporating free Earth oscillation data. Phys. Earth Planet. Int. 2,35. Haddon, R. A. W. and Cleary, J. R. (1974). Evidence for scattering of seismic PKP waves near the mantle-core boundary. Phys. Earth Planet. Int. 8,211. Hage, H. (1981). P and S velocity jump at the inner-core boundary from PKP amplitudes. In Identification of Seismic Sources-Earthquakes or Underground Explosions (E. S . Husebye and S. Mykkeltreit eds), p. 483. D. Reidel, New York. Hage, H. (1983). Velocity constraints for the inner core inferred from long-period PKP amplitudes. Phys. Earth Planet. Int. 31, 171. Hager, B. H., Clayton, R. W., Richards, M. A,, Comer,’R. P. and Dziewonski, A. M. (1985). Lower mantle heterogeneity, dynamic topography and the geoid. Nature 313, 541. Hai, N. (1961). Propagation des ondes longitudinales dans le noyeau terrestre d’apres les seismes profonds de Iles Fidji. Ann. Geophys. 17,60. Hai, N. (1963). Propagation des ondes longitudinales dans le noyeau terrestre. Ann. Geophys. 19, 285. Hales, A. L. and Maki-Lopez, M. L. (1980). P travel times from Nevada test site explosions and the determination of average global P travel times. Phys. Earth Planet. Int. 23, 188. Hales, A. L. and Roberts, J. L. (1970). Shear velocities in the lower mantle and the radius of the core. Bull. Seism. SOC.Amer. 60, 1427. Hales, A. L. and Roberts, J. L. (1971). The velocities in the outer core. Bull. Seism. Soc. Amer. 61, 1051. Hales, A. L., Lapwood, E. R. and Dziewonski, A. M. (1974). Parameterization of a spherically symmetric Earth model with special reference to the upper mantle. Phys. Earth Planet. Int. 9,9. Hannon, W. J. and Kovach, R. L. (1966). Velocity filtering of seismic core phases. Bull. Seism. SOC.Amer. 54,441. Hart, R. S., Anderson, D. L. and Kanamori, H. (1976). Shear velocity and density of an attenuating Earth. Earth Planet. Sci. Lett. 32, 25. Hart, R. S., Anderson, D. L. and Kanamori, H. (1977). The effect of attenuation on gross earth models. J . Geophys. Res. 82, 1647. Herrin, E. (1968). Introduction to the 1968 Seismological Tables for P phases. Bull. Seism. SOC. Amer. 58, 1193. Herrin, E., Tucker, W., Taggart, J., Gordon, D. W. and Lobdell, J. L. (1968). Estimation of surface focus P travel times. Bull. Seism. Soc. Amer. 58, 1273. Hide, R. (1971). Viscosity of the Earth’s core. Nature Phys. Sci. 233,100. Hide, R. and Horai, K. I. (1968). On the topography of the coremantle interface. Phys. Earth Planet. Int. 1, 305. Higgins, G. and Kennedy, G. C. (1971). The adiabatic gradient and the melting point gradient in the core of the Earth. J . Geophys. Res. 76,1870.
76
The Earths Core
Husebye, E. S., King, D. W. and Haddon, R. A. W. (1976). Precursors to PKIKP and seismic wave scattering near the mantle-core boundary. J . Geophys. Res. 81,1870. Ibrahim, A. K. (1971). The amplitude ratio PCPjP and the core-mantle boundary. Pure Appl. Geophys. 91,114. Ibrahim, A. K. (1973). Evidences for a low velocity core-mantle transition zone. Phys. Earth Planet. Int. 7, 187. Jackson, D. D. (1972). Interpretation of inaccurate, insufficient and inconsistent data. Geophys. J . 28,97. Jackson, D. D. and Anderson, D. L. (1970). Physical mechanisms of seismic-wave attenuation. Rev. Geophys. Space Phys. 8 , l . Jacobs, J. A. (1968). The structure of the Earth’s core. Phys. Earth Planet. Int. 1, 196. Jacobs, J. A. (1970). Geophysical numerology. Nature 227,161. Jeanloz, R. and Richter, F. M. (1979). Convection, composition and thermal state of the lower mantle. J . Geophys. Res. 84, 5497. Jeffreys, H. (1936). On travel times in seismology. Bur. Cent. Seism.Inter. A,, Fasc. 14, 1. Jeffreys, H. (1937). On the materials and density of the Earth’s crust. Mon. Not. Roy. Astron. SOC. Geophys. Suppl. 4,50. Jeffreys, H. (1939a). The times of P, S and SKS and the velocities of P and S . Mon. Not. Roy. Astron. SOC.Geophys. Suppl. 4,498. Jeffreys, H. (1939b). The times of PCP and SCS. Mon. Not. Roy. Astron. Soc. Geophys. Suppl. 4, 537. Jeffreys, H. (1939~).The times of the core waves. Mon. Not. Roy. Astron. SOC.Geophys. Suppl. 4, 548. Jeffreys, H. (1939d). The times of the core waves. Mon. Not. Roy. Astron. Soc. Geophys. Suppl. 4, 594. Jeffreys, H. (1961). Theory of Probability. Clarendon Press, Oxford. Jeffreys, H. (1965). The damping of S waves. Nature 208,675. Jeffreys, H. (1967). Radius of the Earth’s core. Nature 215,1365. Jeffreys, H. (1978). On imperfections of elasticity in the Earth’s interior. Geophys. J . 55,273. Jeffreys, H. and Bullen, K. E. (1935). Times of transmission of earthquake waves. Bur. Cent. Seism. Inter. A. Fasc. 11. Jeffreys, H. and Bullen, K. E. (1940). Seismological Tables. British Association, Gray-Milne Trust. Johnson, I. M. and Smylie, D. E. (1977). A variational approach to whole-Earth dynamics. Geophys. J . 50,35. Johnson, L. E. and Gilbert, F. (1972a). Inversion and inference for teleseismic ray data. In Methods in Computational Physics (B. A. Bolt, ed.) vol. 11, p. 231. Johnson, L. E. and Gilbert, F. (1972b). A new datum for use in the body wave travel time inverse problem. Geophys. J . 30,373. Johnson, L. R. (1967). Array measurements of P velocities in the upper mantle. J . Geophys. Res. 72,6309. Johnson, L. R. (1969). Array measurements of P velocities in the lower mantle. Bull. Seism. SOC. Amer. 59,973. Jones, G . M. (1977). Thermal interaction of the core and the mantle and long term behaviour of the geomagnetic field. J . Geophys. Res. 82, 1703. Jordan, T. H. (1972). Estimation of the radial variation of seismic velocities and density in the Earth. PhD. Thesis, California Institute of Technology. Jordan, T. H. and Anderson, D. L. (1974). Earth structure from free oscillations and travel times. Geophys. J . 36,411. Julian, B. R., Davies, D. and Sheppard, R. M. (1972). PKJKP. Nature 235,317.
General Physical Properties of the Earth
77
Kanamori, H. (1967a). Spectrum of P and PCP in relation to the mantle-core boundary and attenuation in the mantle. J . Geophys. Res. 72,559. Kanamori, H. (1967b). Attenuation of P waves in the upper and lower mantle. Bull. Earthquake Res. Inst. 45,299. Karato, S. (1980). Low Q-zone at the base of the mantle: evidence for lower mantle convection? Phys. Earth Planet. Int. 22, 155. Keilis-Borok, V. I. and Yanovskaya, T. R. (1967). Inverse problems of seismology. Geophys. J . 13, 223. King, D. W., Haddon, R.A. W. and Cleary, J. R.(1973). Evidence for seismic wave scattering in the D layer. Earth Planet. Sci. Left.20,353. King, D. W., Haddon, R. A. W. and Cleary, J. R. (1974). Array analysis of precursors to PKIKP in the distance range 128" to 142". Geophys. J . 37, 157. Knopoff, L. (1964). Quart. Rev. Geophys. 2,625. KnopofT, L. and MacDonald, G. J. F. (1958). The magnetic field and the central core of the Earth. Geophys. J . 1,216. Kogan, S. D. (1972). A study of the dynamics of a longitudinal wave reflected from the Earth's core. Bull. Acad. Sci. USSR Earth Phys. 6,3. Kuster, G . T. (1972). Seismic wave propagation in two-phase media and its applications to the earth's interior. PhD. Thesis, MIT, Cambridge, MA. , Landisman, M., Sato, Y. and Nafe, J. (1965). Free vibrations of the Earth and the properties of its deep interior regions. 1: Density. Geophys. J . 9,439. Lay, T. and Helmberger, D. V. (1983a). A shear velocity discontinuity in the lower mantle. Geophys. Res. Lett. 10,63. Lay, T. and Helmberger, D. V. (1983b). A lower mantle S-wave triplication and the shear velocity structure of D . Geophys. J . 75,799. Lee, R. C. and Johnson, L. R. (1984a). Tau estimates for mantle P- and S-waves from global travel-time observations. Geophys. J . 77,655. Lee, R. C. and Johnson, L. R. (1984b). External bounds on the seismic velocities in the Earth's mantle. Geophys. J . 77,667. Lee, W. B. and Solomon, S. C. (1978). Simultaneous inversion of surface wave phase velocity and attenuation: waves in western North America. J . Geophys. Res. 83,3389. Lehmann, I. (1936). " P . Publ. Bur. Cent. Seism. I n t . Ser. A 14,3. Liebermann, R. C. and Ringwood, A. E. (1973). Birch's law and polymorphic phase transformations. J . Geophys. Rex 78,6926. Liu, L. (1982a). The F zone. Geophys. Res. Lett. 9,808. Liu, L. (1982b). Phase transformation in MgSiO, compounds at high pressures and their geophysical implications. Earth Planet. Sci. Lett. 57, 110. Liu, H. P., Anderson, D. L. and Kanamori, H. (1976). Velocity dispersion due to anelasticity: implications for seismology and mantle composition. Geophys. J . 47,41. Loper, D. E. (1984). Structure of the core and lower mantle. Adv. Geophys. 26,l. Loper, D. E. and Fearn, D. R. (1983). A seismic model of a partially molten inner core. J . Geophys. Res. 88, 1235. Luh, P. C. (1974). Normal modes of a rotating self-gravitating inhomogeneous Earth. Geophys. J . 38, 187. Malkus, W. V. R. (1968). Precession of the Earth as the cause of geomagnetism. Science 160,259. Masters, G. and Gilbert, F. (1981). Structure of the inner core inferred from observations of its spheroidal shear modes. Geophys. Res. Lett. 8,569. McMechan, G. A. and Wiggins, R. A. (1972). Depth limits in body wave inversions. Geophys. J . 28,459.
78
The Earth's Care
McQueen, R. G., Fritz, J. N. and Marsh, S. P. (1964). On the composition of the Earth's interior. J . Geophys. Res. 69,2947. Melchior, P, and Ducarme, B. (1985). Detection of inertial gravity oscillations in the Earth's core with a superconducting gravimeter at Brussels. Phys. Earth Planet. Int. 42, 129. Mikumo, T. and Kurita, T. (1968). Q-distribution for long-period P waves in the mantle. J . Phys. Earth 16, 11. Mitchell, B. J. and Helmberger, D. V. (1973). Shear velocities at the base of the mantle from observations of S and SCS. J . Geophys. Res. 78,6009. Mizutani, H. and Abe, K. (1972). An Earth model consistent with free oscillation and surface wave data. Phys. Earth Planet. Int. 5,345. Moon, W. (1982). Variational solution of long period oscillations of the Earth. Geophys. J . 69, 431. Moore, E. H. (1920). Bull. Am. Math. Soc. 26,394. Mula, A. H. G. (1981). Amplitudes of diffracted long-period P and S waves and the velocities and Q structure at the base of the mantle. J . Geophys. Res. 86,4999. Mula, A. H. and Muller, G. (1980). Ray parameters of diffracted long period P and S waves and the velocities at the base of the mantle. Pure Appl. Geophys. 118, 1270. Muller, G . (1973). Amplitude studies of core pkases. J . Geophys. Res. 78, 3469. Muller, G. (1975). Further evidence against discontinuities in the outer core. Phys. Earth Planet. Int. 10,70. Muller, G., Mula, A. H. and Gregersen, S. (1977). Amplitudes of long-period PCP and the coremantle boundary. Phys. Earth Planet. Int. 14,30. Nuttli, 0.W. (1969). Travel times and amplitudes of S waves from nuclear explosions in Nevada. Bull. Seism. SOC.Amer. 59,385. Okal, E. A. and Geller, R. J. (1979). Shear wave velocity at the base of the mantle from profiles of diffracted SH waves. Bull. Seism. Soc. Amer. 69,1039. Olson, P. (1977). Internal waves in the Earth's core. Geophys J . 51,183. ONions, R. K., Evensen, N. M., Hamilton, N. J. and Carter, S. R. (1978). Melting of the mantle past and present: isotope and trace element evidence. Phil. Trans. Roy. Soc. London A258, 547. Parker, R. L. (1970). The inverse problem ofelectrical conductivity in the mantle. Geophys. J . 22, 121. Parker, R. L. (1972a). The BackusGilbert method and its application to the electrical conductivity problem. In Mathematics of Projile Inversion (L. Colin, ed.). NASA Tech. Mem. 62, 150. Parker, R. L. (1972b). Inverse theory with grossly inadequate data. Geophys. J . 29,123. Pekeris, C. L. (1966). The internal constitution of the Earth. Geophys. J . 11,85. Pekeris, C . L. and Accad, Y. (1972). Dynamics of the liquid core of the Earth. Phil. Trans. Roy. Soc,London A273,237. Pekeris, C. L., Alterman, Z . and Jarosch, H. (1961). Rotational multiplets in the spectrum of the Earth. Phys. Rev. 122, 1692. Penrose, R. (1955). A generalized inverse for matrices. Proc. Camb. Phil. SOC.51,406. Press, F. (1968a). Density distribution in Earth. Science 160, 1218. Press, F. (1968b). Earth models obtainedby Monte Carlo inversion. J . Geophys. Res. 73,5223 Press, F. (1970a). Earth models consistent with geophysical data. Phys. Earth Planet. Int. 3,3. Press, F. (1970b). Regionalized Earth models. J . Geophys. Res. 75,6575. Qamar, A. (1973). Revised velocities in the Earth's core. Bull. Seism. SOC.Amer. 63, 1073. Qamar, A. and Eisenberg, A. (1974). The damping of core waves. J . Geophys. Res. 79,758. Randall, M. J. (1970). SKS and seismic velocities in the outer core. Geophys. J . 21,441.
General Physical Properties of the Earth
79
Randall, M. J. (1976). Attenuative dispersion and frequency shifts of the Earth’s free oscillation. Phys. Earth Planet. Int. 12, 1. Richards, P. G. (1973). Calculation of body waves, for caustics and tunnelling in core phases. Geophys. J . 35,243. Richards, M. A. and Hager, B. H. (1984). Geoid anomalies in a dynamic Earth. J . Geophys. Res. 89, 5987. Ringwood, A. E. (1972). Mineralogy of the deep mantle: current status and future developments. In The Nature of the Solid Earth (E. C. Robertson, ed.) McCraw-Hill, New York. Robinson, R. and Kovach, R. (1972). Shear wave velocities in the Earth’s mantle. Phys. Earth Planet. Int. 5, 30. Rochester, M. G. (1970). Coresmantle interactions: geophysical and astronomical consequences. In Earthquake Displacement Fields and the Rotation ofthe Earth (L. Mansinha, D. E. Smylie and A. E. Beck, eds). D. Reidel, Holland. Ruff, L. J. and Helmberger, D. V. (1982). The structure of the lowermost mantle determined by sport-period P wave amplitudes. Geophys. J . 68,95. Sabadini R. and Peltier, W. R. (1981). Pleistocene deglaciation and the Earth’s rotation: implications for mantle viscosity. Geophys. J . 66, 553. Sacks, I. S. (1971a). Anelasticity of the outer core. Carnegie Inst. Year Book 69,414. Sacks, I. S. (1971b). Anelasticity of the inner core. Carnegie Insr. Year Book 69,416. Sacks, I. S. (1972). Q structure of the inner and outer core.’EOS Trans. Amer. Geophys. Union. 53, 601. Sacks, I. S. and Snoke, J. A. (1976). Heterogeneous structure at the base of the mantle, 2, Observations and interpretations. 1lth Int. Symp. Math. Geophys. Seeheim, West Germany. Sacks, I. S. and Snoke, J. A. (1981). Reply to Clark and Pearce. Geophys. J . 66,747. Sacks, I. S., Snoke, J. A. and Beach, L. (1979). Lateral homogeneity at the base of the mantle revealed by observations of amplitides of P K P phases. Geophys. J . 59,379. Sailor, R. V. and Dziewonski, A. M. (1978). Measurements and interpretation of normal mode attenuation. Geophys. J . 53,559. Sato, R. and Espinosa, A. F. (1967). Dissipation in the Earth’s mantle and rigidity and viscosity in the Earth’s core determined from waves multiply reflected from the mantle-core boundary. Bull. Seism. SOC.Amer. 57, 829. Schlittenhardt, J., Schweitzer, J. and Miiller, G. (1985). Evidence against a discontinuity at the top of D”. Geophys. J . 81,295. Sengupta, M. K. and Julian, B. R. (1978). Radial variation of compressional and shear velocities in the Earth’s lower mantle. Geophys. J . 54, 185. Shankland, T. J. and Chung, D. H. (1974). General relationships among sound speeds. 11: Theory and discussion. Phys. Earth Planet. Int. 8,121. Shen, P. Y. (1976). A theory of toroidal core oscillations of the Earth. Geophys. J . 46,307. Shen, P. Y. (1978). On gravitational oscillations of Earth’s outer core. EOS Trans. Amer. Geophys. Union. 59, 1027. Shen, P. Y. (1983). On oscillations of the Earth’s fluid core. Geophys. J . 75,737. Shen, P. Y. and Mansinha, L. (1976). Oscillation, nutation and wobble of an elliptical rotating Earth with liquid outer core. Geophys. J . 46,467. Simmons, G. (1964). Velocity of shear waves in rocks to 10 kilobars. J . Geophys. Res. 69,1123. Simmons, G. and Chung, D. H. (1968). A powder method for determining the elastic parameters of a solid. Trans. Amer. Geophys. Union. 49,308. Simmons, G. and Wang, H. (1971). Single Crystal Elastic Constants and Calculated Aggregate Properties: a Handbook, 2nd edn. MIT Press, Cambridge, MA. Smith, M. L. (1974). The scalar equations of infinitesimal elastic-gravitational motion for a rotating, slightly-elliptical Earth. Geophys. J . 37,491.
80
The Earth’s Core
Smith, M. L. (1976). Translational inner core oscillations of a rotating, slightly elliptical Earth. J . Geophys. Res. 81,3055. Smith, M. L. (1977). Wobble and nutation of the Earth. Geophys. J . 50, 103. Smylie, D. E. (1973). Dynamics of the outer core. Proc. 2nd Int. Symp. Geod. Phys. Earth, Potsdam. Smylie, D. E. (1974). Dynamics of the outer core. Veroff Zentralinst. Phys. Erde. Akad. Wiss. DDR 30,91. Smylie, D. E. and Mansinha, L. (1971). The elasticity theory of dislocation in real Earth models and changes in the rotation of the Earth. Geophys. J . 23,329. Smylie, D. E. and Rochester, M. G. (1981). Compressibility, core dynamics and the sub-seismic wave equation. Phys. Earth Planet. Int. 24,308. Stacey, F. D. (1977). A thermal model of the Earth. Phys. Earth Planet. Int. 15,341. Stacey, F. D. and Loper, D. E. (1983). The thermal boundary layer interpretation of D and its role as a plume source. Phys. Earth Planet. Int. 33,45. Stiller, H., Franck, S. and Schmidt, U. (1980). On the attenuation of seismic waves in the Earth’s core. Phys. Earth Planet. Int. 22,221. Subiza, G. P. and Bath, M. (1964). Core phases and the inner core boundary. Geophys. J . 8,496. Taggart, J. and Engdahl, E. R. (1968). Estimation of PCP travel times and depth to the core. Bull. Seism. SOC.Amer. 58,1293. Teng, T. L. (1968). Attenuation of body waves and the Q structure of the mantle. J . Geophys. Res. 73,2195. Wang, C.-Y. (1968). Constitution of the lower mantle as evidenced from shock wave data for some rocks. J . Geophys. Res. 73,6459. Wang, C.-Y. (1970). Density and constitution of the mantle. J . Geophys. Res. 75,3264. Wang, C.-Y. (1972). A simple Earth model. J . Geophys. Res. 77,4318. Wiggins, R. A. (1969). Monte Carlo inversions of body wave observations. J . Geophys. Res. 74, 3171. Wiggins, R. A. (1972). The general linear inverse problem: implication of surface waves and free oscillations for Earth structure. Reu. Geophys. Space Phys. 10,251. Wiggins, R. A,, McMechan, G . A. and Toksoz, M. N. (1973). Range of Earth structure nonuniqueness implied by body wave observations. Rev. Geophys. Space Phys. 11,87. Williamson, E. D. and Adams, L. H. (1923). Density distribution in the Earth. J . Wash. Acad. Sci. 13,413. Won, I. J. and Kuo, J. T. (1973). Oscillation of the Earth’s inner core and its relation to the generation of geomagnetic field. J . Geophys. Res. 78,905. Worthington, M. H., Cleary, J. R. and Anderssen, R. S. (1972). Density modelling by Monte Carlo inversion. 11: Comparison of recent Earth models. Geophys. J . 29,445. Wright, C. (1973). Array studies of P phases and the structure of the D region of the mantle. 1. Geophys. Res. 78,4965. Wunsch, C. (1974). Simple models of the deformation of an Earth with a fluid core, I. Geophys. J . 39,413. Wunsch, C. (1975). Simple models of the deformation of an Earth with a fluid core, 11. Dissipation and magnetohydrodynamic effects. Geophys. J . 41,165. Zener, C. (1948). Elasticity and Anelasticity ofMetals. Chicago University Press, Chicago. Zharkov, V. N., Karpov, P. B. and Leontjev, V. V. (1985). On the thermal regime of the boundary layer at the bottom of the mantle. Phys. Earth Planet. Int. 41,138.
Chapter Two
The Origin of the Core
2.1
Introduction
A fundamental question in any discussion of the Earth’s core is its origin. Has the Earth always had a core, or has its present structure evolved over geological time? Such a question cannot be divorced from the much broader issue of the origin of the Earth itself. There is one constraint, however, that can be imposed upon possible evolutions. Most theories of the origin of the Earth’s magnetic field ascribe it to motions in the liquid OC (see $4.2). Rocks as old as 3500 Ma have been found which possess remanent magnetization, so that it is extremely probable that the Earth had a molten OC, comparable in size to that at present at least that long ago. No similar deductions can be made about the state of the IC. With regard to the broader question of the origin and evolution of the solar system, it must not be forgotten that it is by no means certain a priori that the problem can be given a definite answer. It may well be that all memory has been lost of the circumstances under which our solar system was born. All that we can do is to attempt to derive its present state from an assumed event or series of events that occurred in the distant past. Thus, in a sense, the method is one of trial and error. It is more reasonable to assume that planets are normally present in the vicinity of certain stars than to suppose that our planetary system is unique or at least very rare-there are about 200,000 million stars in our galaxy alone. The origin of the solar system is thus part of a very much larger problem-the evolution of the sun and stars in general. Theories of the origin of the Earth and other members of the solar system 81
82
The Earth's Core
may be classified in a number of ways. The Earth may have cooled from a hot gas or accreted cold from dust particles, probably of composition similar to that of chondritic meteorites. In the past, most theories of the origin of the Earth have assumed that the proto-Earth was homogeneous and that the present differentiation into a core, mantle and crust occurred later. There are, however, a number of difficulties with such theories, and there has been some discussion in recent years of non-homogeneous models. In such models, the core of the Earth is formed first and the mantle is deposited upon it later. Non-homogeneous models can also have either a hot or a cold origin. A hot origin involves a consideration of the order of condensation of the elements in the primitive solar nebula; a cold origin involves a study of the mechanics of the accretion process. 2.2
The Accretion Mechanism
Regardless of how stars like the sun form, at some time matter in the form of grains or small bodies must have aggregated to form the terrestrial planets. There are two possible mechanisms by which this may have been accomplished-gravitational collapse and accumulation. In the first case, matter aggregates into larger objects under the influence of a gravitational field following a gravitational instability. In the second case, bodies grow by the gradual addition of matter following collisions and coherence. These two processes may occur with or without the presence of a dynamically significant gas phase. During the initial stages of the evolution of the solar system, large amounts of gas must have been present and the beginning of planetary growth must have involved a gas phase. However, it is possible that the gas was removed by solar ultraviolet or corpusular radiation on a time-scale less than that required for the growth by collisions of the initial solid bodies that formed from gravitational instabilities in the dust layer of the solar nebula. A large body of literature exists on gas-free accumulation models of the evolution of the terrestrial planets: see, for example, Safronov (1969). The evolution of terrestrial planetary material from dust to planets can be considered in roughly three main stages. The early stage, producing kilometre-size planetesimals formed by smallscale gravitational instabilities of the dust layer alone. The intermediate stage, during which kilometre-sized planetesimals grow to 1000-km-sized bodies. The dynamical evolution of this stage is governed by two competing mechanisms: collisional fragmentation and gravitational accumulation. The late stage, or final stage, during which 1000-km-sized embryos grow to full-sized planets, with the right orbital spacing, eccentricities, inclina-
The Origin of the Core
83
tions, and rotations. Wetherill (1980a) has reviewed in detail these different phases of the formation of the terrestrial planets. For the smallest particle sizes, accumulation cannot be very rapid. The particles will collide, partly as a result of their Brownian motion in the gas, and partly as a result of acceleration by very weak electric fields that can be expected to be produced in the nebula through the interaction of convection with ionization produced by natural radioactivity. This state of accumulation may be greatly accelerated as a result of the natural magnetism of the interstellar grains. Purcell and Spitzer (1971) believe that the interstellar grains most probably would be ferromagnetic or super-paramagnetic, so that they could be aligned by the very weak interstellar magnetic field. If this is the case, and it appears to be consistent with evidence from meteorites (Brecher, 1971), then the interstellar grains would be able to come together to form considerably larger units, both during the late stages of the collapse that formed the primitive solar nebula and during the early history of the solar nebula itself. The cross-section for magnetic capture of one particle by another would be very much greater than the geometric cross-sections involved in ordinary non-magnetic collisions. The initial step is the presence of interstellar grains in the gas which, after some dregree of gas absorption, find themselves concentrated in the nebular plane and somehow manage to accrete into larger bodies. The main problem is the fact that the number of these bodies must eventually be considerably reduced: from swarms of small bodies, eventually a few large planets must be produced. This reduction can only take place by collisions. The model of Safronov (1969, 1972) starts with a quiet nebula in which dust particles rotate and begin to sink slowly (under gravity) towards the equatorial plane. The assumption is made that all the particles such a dust particle meets on the way down adhere to it, and, upon arriving at mid-plane (after 2: 103-104 years) it has reached a size of N 1 cm. The critical assumption is the so called “cold welding” of matter which represents an upper limit to the efficiency of the process. When the density of the dust layer exceeds a certain value, condensation of matter would be induced by gravitational instabilities. In those regions close to the sun, gas motions would have been too fast for gravitational instabilities to take place and growth of bodies could only occur through aggregation during collisions. Safronov argued that the relative velocities of the bodies would be determined by their gravitational perturbations at encounters and should be less than 1 m s - so long as the objects were less than 5 km in diameter. Alfvkn and Arrhenius (1970a,b, 1973) solved the problem of reducing the relative velocities of colliding bodies so as to facilitate coalescence by the concept of “jet” streams. They argued that collisions
a4
The Earth‘s Core
between particles in Keplerian orbits do not lead to a spreading but to an equalization of the orbits of the particles when the collisional frequency is smaller than the orbital frequency. This state, in any theory of this type, either prevails originally or develops by accretion. It results in a focusing of particles into jet streams with increasingly similar orbital elements and velocities of the individual particles. The partially inelastic collisions will lead to the growth of embryo bodies of which some eventually reach the size where gravitational accretion becomes increasingly important. Alfven and Arrhenius believe that the maximum possible velocity for accretion is 0.5 km s- It must be pointed out that the jet stream hypothesis of Alfvtn and Arrhenius has not been universally accepted (see e.g. Reeves (1972), p. 86-87, for a discussion on this point). Cameron (1972) has also recognized that, during the lifetime of the nebula, collision probabilities were too low for accretion to take place in any reasonable time. He suggested, however, that during the collapse phase from the interstellar cloud to the nebula the situation was much more favourable, since violent gas motions (in the form of turbulent eddies) would have considerably increased the collision probabilities of gas and grains. Cameron estimated typical grain velocities to be N 10 m s-’. At the end of the collapse the nebula is formed and turbulence rapidly decays out, embedding a set of bodies up to 20 cm in radius. Goldreich and Ward (1973) investigated the process whereby dust particles can accrete to form gravitationally active objects. They concluded that gravitational instabilities can account for the growth of objects up to several km in radius. These instabilities develop, not in the gaseous solar nebula, but in a thin disc of particulate matter that forms in the central plane during an initial condensation phase. A first generation of planetesimals whose radii range up to 0.1 km form from this dust disc by gravitational collapse in a time-scale of order 1 year. The resulting disc of first-generation planetesimals is still gravitationally unstable and the planetesimals group into clusters. The clusters then contract on a time-scale of a few thousand years to form a second generation of planetesimals having radii of order 5 km. The contraction is controlled by the rate at which gas drag damps their internal rotation and random kinetic energy. In Goldreich and Ward’s model planetary accretion does not depend on the if the dust grains tend to “stickiness” of the surface of the dust particles-ven stick together upon impact, the growth of solid bodies by this process would be much slower than by gravitational instabilities. However, Weidenschilling (1980) pointed out that non-Keplerian rotation of the solar nebula results in shear between the gas and a dust layer. This shear produces turbulence within the layer that inhibits gravitational instability unless the mean particles are larger than a critical size (- 1 cm at 1 AU). Weidenschilling believes that
’.
85
The Origin of the Core
some coagulation of grains is possible in the solar nebula; Van der Waals forces may be sufficient to allow formation of centimetre-sized aggregates during settling to the central plane. Growth is primarily due to the sweeping up of small particles by larger ones: settling times are lo3 years in the inner nebula and lo4 years in the outer regions. Drag-induced relative velocities then result in collisions and larger bodies can accrete if reasonable impact lo3cm, relative velocities decrease strength is assumed. After sizes reach and the growth rate declines. Damping of out-of-plane motions by gas drag concentrates these intermediate-sized bodies into a thin layer that is subject to gravitational instability. Kilometre-sized planetesimals are then formed. In Weidenschilling’s model, the formation of planetesimals is a composite process involving, first, a stage of collisional accretion, followed by gravitational instability. Similar conclusions were reached by Nakagawa et al. (1981) using a different numerical method and different assumptions in their model. In the evolution of a growing swarm of planetesimals, relative velocities will be increased by mutual gravitational perturbations, and decreased by dissipative collisions. If the relative velocity is too high (say, several times the gravitational escape velocity of the growing planet), fragmentation rather than accumulation will be dominant and planets will not grow. On the other hand, if relative velocities are too low, the system of planetesimals will be in nearly circular concentric orbits, and the collisions required for growth will not take place. Safronov (1962) showed that for plausible assumptions regarding dissipation of energy in collisions, and size distribution of the bodies, the mutual gravitational perturbations of the bodies cause their mean relative velocity to be only somewhat less than the escape velocity of the larger bodies. Thus, throughout the entire course of planetary growth, from 1-km planetesimals to Earth-sized planets, the system regulated itself in such a way that the larger bodies could always grow, whereas smaller objects would fragment. In its initial, non-gravitational stage, the accretion process may be regarded as a series of collisions between grains in intersecting orbits under conditions that result in a net transfer of mass to some of the grains. An important parameter for accretion theories is the range of impact velocities over which accretion occurs. Kerridge and Vedder (1 972) experimentally investigated this velocity range by observing the impact at different velocities of particles similar to material thought to be present in the early solar system. The projectile material used was kaolinite (a hydrated aluminium silicate) in the form of thin micrometer-sized laminated flakes with a density of 2.63 g cm-3. Such material structurally resembles the major mineral component of the primitive type I carbonaceous chondrites and may well have been widespread in the early solar system. For target material, thick ( - 5 mm) sections of clinochrysotile (a magnesium silicate) with a density of 2.50 g cm- were
-
-
-
86
The Earths Core
used. They found that in any velocity range, impacts in which a significant transfer of projectile material occurred were outnumbered by those in which little or no transfer took place. Moreover, such impacts, at least those above 2 km s-’ were accompanied by the formation of craters with dimensions comparable to or greater than those of the projectile. Thus no accretion could take place for impacts in the velocity range studied (1.5-9.5 km s-l). By contrast, Neukum (1968) showed that for micrometer-sized iron particles impacted into a variety of metallic targets, almost the entire projectile mass is transferred to the target in the velocity range 0.5-13 km s - I . Below 0.5 km s - ’ iron particles rebounded from the metallic targets. There is thus a striking difference between the accretion behaviour of silicates and that of metals-over at least part of the velocity range in which silicate accretion was efficient, metal particles would have rebounded without accreting. Simple accretion theory cannot, therefore, be applied to silicate particles in markedly dissimilar orbits but must be restricted to situations characterized by generally low interparticle velocities. Whether or not impacts at lower velocities can actually lead to accretion of material is not known. No obvious sticking mechanism exists for bonding normal silicates together during lowvelocity impact, although a number of mechanisms have been proposed based on assumed properties of primordial dust grains. Possibly the sticking process was aided by the presence of the volatile coatings on the grains. Alternatively, adhesion may have been prompted by electrostatic charge asymmetries produced in the surface regions of circumsolar grains by charged particle irradiation, as proposed by Arrhenius et al. (1972) A third possible mechanism, suggested by Maurette and Bibring (1972), is the release of stored energy from the irradiation-damaged amorphous rims of grains exposed to the solar wind. Kerridge and Vedder (1972) suggested that metal-silicate fractionation in the solar system may have been affected by differences in the accretionary behaviour of metal and silicate particles. In particular, at the low velocities that must have prevailed during most of the accretionary process, silicates would have preferentially accreted. Similarly, if some regions of the solar system were characterized by higher interparticle velocities, bodies enriched in metal may have been produced. In this respect it may be significant that among the terrestrial planets there is a rough tendency for density, and therefore assumed metal content, to increase with orbital velocity. Dole (1970) developed a computer program to simulate the formation of planetary systems. Planets are assumed to form by aggregation of particles within a cloud of dust and gas surrounding the newly-formed sun. In his model nuclei are “injected” into the cloud one at a time, on elliptical orbits. The dimensions of the semimajor axis and the eccentricity of the orbit of each nucleus are determined by using random numbers. As the nuclei orbit within
87
The Origin of the Core
I
I
I
I I
0.11 -.-.--.
I I ' I
-.-.0.12
2
0.0001
0.36 :
0.005 0.04
0.36
0.05
0.06
""I
2.50
1.27
0.003
I I
I
I
" h
1.08
-
r
\
13.4 n
1.08 0.821
0.1 1 -
-
1
0.15
0.18 .
I
0.1
I
0.24
I I i l l l l I 1 I 1 I 1 I l l 1 10 Orbital distance (a. u.)
1
2.43
I
I I
I t l L
100
Fig.2.1. Planetary systems generated by Dole (1 970). Solid circles represent terrestrial planets, while open circles indicate Jovian planets that have accreted gas as well as dust. The radius of each circle is scaled solely by the cube root of the planet's mass, given in the figures in units of Earth masses. The positions of Jovian planets are given by the centres of the circles. All planets produced are well separated, as the relative positions of their centres indicate. (After lsaacman and Sagan. 1977.)
the cloud they grow by aggregation and gradually sweep out dust-free annular lanes. If they grow larger than a specified critical mass they can begin to accumulate gas as well from the cloud. If the orbit of a planet comes inside a certain interaction distance from a planet that was formed earlier, or if the orbits cross one another, the two bodies coalesce to form a single, more massive, planet which may then continue to grow by aggregation. The process of injecting nuclei is continued until all the dust has been swept from the system. Each planetary system produced by using a different random number sequence is unique. However, all the systems so produced share the major regular features of our solar system (see Fig. 2.1.) The orbital spacings have patterns of regularity suggestive of "Bode's Law". The innermost planets are small rocky bodies; the mid-range planets are large gaseous bodies; the outermost planets are generally small. The general pattern of planetary mass distribution is similar to that in our solar system with masses ranging from less than that of Mercury to greater than Jupiter's. Dole was able to produce planetary systems of recognizable characteristics
a8
The Earth’s Core
only with a certain choice of input parameters and assumed structure of the solar nebula. Isaacman and Sagan (1977) investigated the consequences of varying these parameters and assumptions. They found that only for a small subset of conceivable cases are planetary systems generated that are closely like our own. Many models have tendencies toward one of two preferred configurations: multiple-star systems, or planetary systems in which Jovian planets either have substantially smaller masses than in our system or are absent altogether. However, for a wide range of cases recognizable planetary systems are generated, ranging from multiple-star systems with accompanying planets, to systems with Jovian planets at several hundred astronomical units, to single stars surrounded only by asteroids. Many systems exhibit planets like Pluto and objects of asteroidal mass, in addition to usual terrestrial and Jovian planets. No terrestrial planets were generated more massive than five Earth masses. The number of planets per system is for most cases of the order 10, and, roughly, inversely proportional to the orbital eccentricity of the accreting grains. All systems generated obey a relation of the TitiusBode variety for relative planetary spacing. Isaacman and Sagan comment that it is rather remarkable that such a simple and incomplete model, based merely on Newtonian physics and accretion with unit sticking efficiency, should generate plausible planetary systems for a wide variety of initial conditions. A problem with these simulations is the neglect of mutual gravitational perturbations, which could play a major role during the latest stage of planetary growth. Also, velocities are assumed that are impossibly high in the gaseous interplanetary medium. In his models, Hills (1970) includes gravitational perturbations but ignores collisions. Wetherill (1978) has discussed the shortcomings of many of these earlier attempts at numerical simulations of multi-planet growth and pointed out that in the real solar system accumulation of the terrestrial planets proceeded more or less simultaneously. Greenberg et al. (1978a) carried out a numerical simulation of collisional and gravitational interactions in a possible early solar system. Their results show that “planets” 500 km in diameter can be generated from an initial swarm of kilometre-sized planetesimals, such as might have resulted from gravitational instabilities in the solar nebula. Their models are based on experimental (see Hartmann, 1978) and theoretical impact results (such as rebound, cratering and catastrophic fragmentation) for a reasonable range of parameters and initial conditions. The experimental work of Hartmann indicated that by the time bodies of multi-metre size have formed, they should have regolith surfaces or granular structure throughout. Regolith strongly favours accretion by inhibiting rebound, so that such bodies would have grown very efficiently by collisions with neighbouring bodies. The small planets grow fast on time-scales of a few tens of thousands of years, during which time most of the mass of the system continues to remain in particles
89
The Origin of the Core
near the original size. Relative random velocities remain of the order of a kilometre-sized body’s escape velocity, those of the largest objects being somewhat lower because of damping by the bulk of the material. Greenberg et al. suggested that the few 500-km-sized planets, in a swarm still dominated by kilometre-scale planetesimals, may act as seeds for the subsequent, gradual accretional growth into full-sized planets. While there are uncertainties about many stages of the origin of the solar system and planetary accretion, one of the most serious questions concerns the intermediate phase of accretion, i.e. growth after the hypothetical formation of planetesimals by gravitational instability (Safronov, 1972; Goldreich and Ward, 1973) but before the later stages of accretion when the largest bodies have substantial gravitational cross-sections. It is not clear how planetesimals could have efficiently accreted one another. However, the modelling of Greenberg et al. (1978a), based on detailed physical experiments involving low-velocity collisions among rocky bodies, demonstrates that accretion through this intermediate size range is efficient and rapid-it is a natural result of low-velocity rebound phenomena. Greenberg et al. point out that additional physical processes might be important in this intermediate stage, such as resonant phenomena that might accelerate or retard growth in certain zones, and gas-drag. A potentially disrupting influence on accretion would be high-velocity bodies, perhaps scattered into the zone of interest by an early-formed Jupiter. In this regard, Hartmann (1978) suggested that highvelocity planetesimals passing through the asteroid belt could have stopped further growth of Ceres, rather than a lack of accretable material. Greenberg (1979) later considered the problem of the size of the largest planetesimals that grew near, and later impacted, those that became full-sized planets. The question is important since the final stages of the growth of a terrestrial planet would significantly affect many of its fundamental properties, such as its thermal history and petrology. Greenberg showed that given the range of plausible mechanisms, parameters and initial conditions, possible results for the radius of the second largest planetesimal in the Earth’s zone range from only a few hundred kilometres to 2500 km, with corresponding accretion times of 7 x lo6 and lo8 years respectively. Cox (1978) and Cox and Lewis (1980) carried out numerical simulations to determine whether terrestrial-like planetary systems could be produced as a result of gravitationally-induced collisions and accretions occurring in a swarm of protoplanets assumed to have already reached approximately lunar mass. In their calculations the mass and relative velocity distributions of the bodies are free to evolve simultaneously in response to close gravitational encounters and occasional collisions between bodies. Thus, collisions between bodies arise in a natural way and assumptions concerning the relative velocity distribution and the gravitational collision cross-section are
-
-
90
The Earth‘s Core
unnecessary. The initial eccentricities of the orbits were randomly chosen from a uniform distribution ranging from zero to emax.Their model was twodimensional: the inclinations remain zero throughout the evolutionary ~ 0 . 1 0resulted in process. Cox and Lewis found that simulations with emax final-state configurations having many bodies of nearly equal mass, none of which were comparable to that of the Earth or Venus. Simulations with emax >0.20 resulted in a substantial number of catastrophically disruptive collisions between bodies. On the other hand, simulations with emaxN 0.15 gave six planets, surprisingly close to the actual number (4), with spacings between orbits resembling those of the terrestrial planets. This rather large value of emaxis mainly the consequence of assuming coplanar motions. Cox and Lewis estimated the length of time for the stage of accretion considered in their simulations to be ~2 x lo7 years. Wetherill (1978) and Greenberg et al. (1978b) have questioned whether a self-contained swarm can avoid premature orbital isolation of embryo planets, with the consequent production of too many small bodies. Wetherill (1980b) also investigated to what extent the simulations of Cox (1978) and Cox and Lewis (1980) depend on the calculations being two-dimensional. Wetherill used a different (less exact) method of calculation, but reproduced = 0.05 and 0.10 for the two-dimensional case in which 8 Cox’s results for emax to 10 bodies finally remain. In the three-dimensional case, the final number of bodies is reduced to 3-5 for a low value of emax= 0.05 (see Fig. 2.2) The difference between the three- and two-dimensional results is a consequence of the lesser importance of collisions relative to gravitational perturbations in three dimensions. The time-scale for accretion is lo8 years, most of it occurring during the first 20 Ma. The three-dimensional treatment allows accumulation to proceed for a longer time prior to the separation of embryo planets into isolated orbits*. Spaute et al. (1985) have studied the dynamical evolution of an initial population of kilometre-sized planetesimals in the early solar system subject to collisions, taking into account accretion, rebound, cratering and catastrophic fragmentation. They used a Monte-Carlo statistical method which yielded the mass and velocity distribution of the planetesimals as a function of time and heliocentric distance. They carried out a number of computations simulating the accretional growth of planetesimals (initial mass N 10l6g) in the absence (or presence) of gas-drag, with (or without) one larger embryo among them and with (or without) a size gradient. The work of Spaute et al.
-
* Wetherill has since carried out more sophisticated similar calculations (in Origin of the Moon, W. K. Hartmann, R. J. Phillips, G. J. Taylor eds, Lunar & Planetary Institute, Houston, 1986). He concluded that for a wide range of initial conditions, terrestrial planet accumulation was characterized by giant impacts, ranging in mass up to 3 times that of Mars, at typical impact velocities of 9 km s - I .
-
91
The Origin of the Core
I
l
l
l
15
,
l
0.8
,
25
l
l
l
l
l
l
l
l
l
l
l
l
11
2rcl9
-
21 w
42 w l
l
w -
w
H
l
34
30
13
l
l
W
w
I
l
39
16 w
0.4
l
1
i
24
l
l
1.2
l
l
l
l
l
l
1.6
l
l
2.0
l
l
l
2.4
Heliocentric distance (a.u.1 Fig. 2.2. Final distribution of mass found in three-dimensional calculations of multiplanet accumula= 0.05). The tion. A reasonable number of planets is formed even for low initial eccentricities (emax numbers represent the percentage of the total mass of the system. (After Wetherill 1980a.b.)
is an extension of that of Greenberg et al. (1978a) by considering the effect of gas-drag. Gas-drag can cause some planetesimals to move inside the feeding zone of an embryo, allowing their further growth to reach planetary size. This could help to overcome the difficulty of embryos becoming isolated from the remaining population. Nakagawa et al. (1983) also considered the effect of gas in their study of the evolution of intermediate-sized planetesimals. However, the effect of gas-drag is more important in the simulations of Spaute et al. than in those of Nakagawa et al., since the initial mass of the planetesimals in Spaute et al.3 models is one-hundredth of the mass assumed by Nakagawa et al. Specifically, Spaute et al. showed that, assuming an initial negative size gradient as the heliocentric distance increases, local accumulation of planetesimals can take place by gas-drag alone leading to embryos a few hundred kilometres in radius. Moreover, when an embryo is present among a population of planetesimals, its growth is about twice as rapid in the presence of gas-drag since gas-drag allows a continuous feeding of the embryo by planetesimals moving inwards towards the sun. When an embryo has become massive enough, it becomes more and more efficient in inhibiting the inward diffusion of planetesimals, limiting the growth of the next inner embryo. Such a process may have acted to prevent the formation of many small planets in contrast to the few large existing ones. Cazenave et a!. (1982) have also carried out numerical simulations of the latest stages of planet growth. They considered the motions of a small number of large protoplanets of unequal mass in orbit around the sun.
92
The Earth's Core
Mutual gravitational perturbations, accretion and collisional fragmentation are all taken into account. Their model is three-dimensional, gravitational encounters are treated exactly by numerical integration of the N-body problem, and the outcome of collisional fragmentation is based on the model of Greenberg et al. (1978a). They found that motion during close encounters departs significantly from that predicted by the two-body approximation. For large protoplanets (mass loz5g), accretion always prevails against fragmentation as long as relative velocities are not too great. The mean eccentricities and inclinations evolve towards a steady state, the average value of the inclination (in radians) being about one-half that of the eccentricity. Also, the population evolves towards a quasi-equilibrium relative velocity distribution whatever the initial conditions. Wetherill later (1985) extended his earlier (1980a, 1980b) work on the late stages of growth of the terrestrial planets. He considered the simultaneous growth of several planets from planetesimals in the absence of gas-drag using three-dimensional numerical calculations. He supposed that as most of the mass began to be concentrated in larger bodies, further evolution would be dominated by perturbations by large bodies in orbits of low eccentricity in neighbouring zones rather than by collisions of small bodies. This would cause the eccentricities to increase gradually and Wetherill estimated that there would be -500 bodies of mass -2.5 x when they reached -8 x g (i.e. - 3 the lunar mass). During the first 1.8 Ma, mutual perturbations increased eccentricities to values as high has 0.2. After 9.4 Ma two bodies with masses greater than 3 x loz7g and with relatively low eccentricities (about 0.03 or less) and inclinations ( < 3") formed, in addition to a large number of g (the size of Mercury or Mars). bodies with masses in the range loz6to At this stage, 71% of the final mass of the Earth accumulated. During the last stages of accumulation, requiring up to 2 x lo8 years, almost all these intermediate-mass bodies, including failed planets with masses greater than 3 x loz6g, collided and merged with the two bodies in orbits similar to those of the present Earth and Venus. The accumulation process was accompanied by the impact of very large bodies-as large as three times the mass of Mars at velocities of -9 km s-'. The kinetic energy released in these largest impacts would be several times greater than that required to melt the entire Earth. The Earth, as it grew, would have been at least partially melted throughout, leading to core formation by gravitational segregation of iron. A problem common to all models of cold origin is the means by which the Earth would have heated up sufficiently to lead to a (predominantly iron) molten OC at least 3500 Ma ago. This problem will be discussed in the next section.
-
93
The Origin of the Core
2.3 Heat Sources for an Earth Accreting Cold 2.3.1
Long-lived Radioactive Isotopes
The radioactive isotopes that contribute significantly to the present heatproduction within the Earth are 238U,235U,232Thand 40K,all of which have half-lives comparable to the age of the Earth. The temperature increase due to the radioactive decay of these long-lived isotopes is thus small, of the order of 150 K after 100 Ma (MacDonald, 1959). During the first 1000 Ma, the temperature increase would only be about 700 K (assuming no heat escape) while the total heat produced over the life-time of the Earth (-4500 Ma), if trapped within the Earth, would raise the temperature by 1800 K. Thus long-lived radioactive isotopes can account for part of the initial heating of the Earth, but other sources are necessary as well. It is usually assumed that there is no uranium in the Earth’s core, since uranium (and potassium) exist as siderophobic compounds, such as silicates and oxides in the Earth’s mantle, and were thus thought to be immiscible with the metal core (Urey, 1952). However Hodkin and Potter 1980) have carried out experiments on the binary system of steel and UO, and shown that above 3120 K the system is a two-phase liquid, one rich in UOz and the other poor in UOz. Their phase diagram predicts that there must be a temperature above which there is total miscibility between UO, and steel. Feber et al. (1984) thus suggested that uranium is steadily dissolving into the core and supplying radioactive heat, sufficient to power the geodynamo (see $4.6). The power required is IOl3 W (Gubbins 1981). Murrell et al. (1983), Murrell and Burnett (1985,1986) have carried out experimental work on the partitioning of K, U and Th between sulphide and silicate liquids. Contrary to what has usually been assumed, they found U and Th partitioning into Fe FeS liquids much more important than K partitioning. Of course, uranium could not act as a heat source in the core to power the geodynamo until the core was already molten. If the power required (- 1013 W) is supplied solely by the decay of 40K, the K concentration currently required in the core is 1500 ppm. On the other hand, the actinide core concentrations’ currently required are about 50 ppb U or 180 ppb Th. The question of the possibility of K in the Earth’s core is discussed further in Section 5.8.
-
-
-
2.3.2 Short-lived Radioactive Isotopes
Short-lived radioactive isotopes could have contributed to the initial heat of the Earth if the time between the formation of the elements and the aggregation of the Earth was short compared with the half-lives of the isotopes. The
94
The Earfhs Core
most important short-lived isotopes are 236U,I4%m, 244Puand 247Cm,all of which have half-lives sufficiently long to have heated up the Earth for some tens of million years after the initial formation. These four isotopes would, in fact, have contributed about 20 times the heat produced by 40K during this period. The decay of three shorter-lived radionuclides 26A1, 36Cl and 60Fe would have significantly heated up accreting planetary bodies for a period of about 5-15 Ma after the termination of nucleosynthesis in the primitive solar system (Fish et al., 1960). Of these, 26A1 is the most important. It decays to 26Mgwith a half-life of 0.74 Ma and would remain as a significant source of heat for about 10 Ma. If the Earth accreted within 20 Ma of the termination of nucleosynthesis, the heat released through the decay of 26A1 could be the main cause of its high internal temperature. If, on the other hand, the time of accretion was of the order of 100 Ma, the decay of 26A1would have had a negligible effect on the Earth's thermal history. In this regard, no trace of any anomaly in the 26Mg/24Mgratio had, until recently, been found in meteorites or in lunar and terrestrial samples (Schramm et al., 1970). Gray and Compston (1974), however, found an anomalous value of the 26Mg/24Mg ratio in a melilite-bearing chondrule in the Allende meteorite. They suggested that the anomaly results entirely from excess 26Mg,implying an origin by the radioactive decay of 26Al formed during intense proton irradiation in the early stages of the solar system. Later, Typhoon Lee et al. (1976, 1977) measured the isotopic composition of Mg in different phases of a Ca-Al-rich inclusion in the Allende meteorite and found large excesses of 26Mg of up to 10% that correlated with the 27A1/24Mgratio for four coexisting phases with distinctive chemical compositions. They concluded that the most plausible cause of the 26Mganomaly is the decay in situ of 26A1,providing definite evidence for the presence of 26A1in the early solar system. This would require either injection of freshly synthesized nucleosynthetic material into the solar system immediately before condensation and planet formation, or local production within the solar system by intense activity of the early sun. One suggestion to account for the excess 26Mg in the aluminium-rich minerals from the Allende meteorite is that a supernova exploded beside the forming solar system, peppering the solar cloud from which Allende formed with 26A1. This conclusion has now been questioned by the detection of surprisingly large amounts of 26A1in the interstellar medium (Mahoney et al. 1984; Mahoney 1985) by the third HighEnergy Astrophysical Observatory (HEAO 3). The concentration is approximately 1 atom of 26A1 on the average for every 100,000 atoms of 27A1. This discovery has been confirmed by a pray spectrometer on board the Solar Maximum Mission Satellite (Share et al., 1985) The prays coming from the general direction of the galactic centre are a product of the P-decay of the 26A1 nucleus. Clayton (1984) showed that if the 26A1 is spread uniformly
The Origin of the Core
95
throughout the interstellar gas, its concentration (- 10 ppm of Al) is close to that in the Allende minerals, in which case it is unnecessary to invoke the injection of 26A1into the forming solar system by a supernova. In any case, supernova explosions are not adequate to maintain the average level of observed interstellar radioactivity. The excess of 26A1 in Allende minerals, however, is too large to be the result of the average interstellar concentration. If 26A1decayed in the Allende minerals, there must have been some source of 26A1enhancement in the solar cloud as it collapsed to form the solar system. Clayton (1984) now expresses some doubts that 26A1 was ever "alive" in Allende. Some information on the time of nucleosynthesis has come from a study of xenon isotopes. "'I decays through p-emission to "'Xe with a half-life of 16.4 Ma. This half-life is so short that no "'I now exists in nature. However, this isotope should be produced at the time of formation of the other elements. It can be expected that the condensation of planetary material would incorporate any of the iodine present, but would be unlikely to incorporate much xenon. "'Xe formed within the condensed materials would be trapped and might be observed today-very small amounts of excess "'Xe have in fact been found in a number of meteorites. Absolute formation intervals calculated by the 129Xe-1291method generally give values between 40 and 300 Ma depending on the nucleosynthesis model assumed. Variations in relative formation intervals are much less, but are difficult to assess because of different methods of data treatment between different laboratories. Podosek (1970) has subjected all of the Berkeley data to a common method of analysis and found 15 different meteorites possessing formation intervals within a period of 15 Ma. Other noble-gas components in meteorites that arise from an extinct radionuclide and have the potential for the determination of formation intervals are the heavy xenon isotopes 131-136Xethat arise from the fission of 244Pu. These fission Xe components are much more difficult to identify than the excess lZ9Xe and were not discovered until precise isotopic data were obtained on the calcium-rich achondrites, a class of meteorites high in uranium (supposedly chemically similar to plutonium) and very low in trapped Xe (Rowe and Kuroda, 1965). Rao and Gopalan (1973) have also considered the fission Xe components in different types of meteorites and in particular have investigated whether some actinide isotopes could produce the excess fission Xe found in primitive chondrites. They concluded that the I-Xe and Cm-Xe systematics relate to different events in the early history of the solar system. The former refers to the time when I-Xe clocks are re-set during metamorphism of the ordinary chondrites while the latter refers to the time of primary condensation of the refractory materials from the cooling solar nebula (Hoyle and Wickrama-
96
The Earth's Core
singhe, 1968). The occurrence of the short-lived nuclide 248Cm ( Q T , ,=~ 0.4 Ma) in primitive meteorites has important consequences for the time-scales of the earliest events in the evolution of the solar system. As the solar nebula cools from about 2000 to 1400 K, i.e. to the temperature at which iron and magnesium silicates condense, the high-temperature minerals (or phases) form as refractory condensates (Fireman et al., 1970; Podosek and Lewis, 1972). Curium, being a refractory element similar to uranium, plutonium and the rare-earths, is most likely to be incorporated into these minerals, which would preserve the spontaneous fission record of 248Cmif they cooled fast to the Xe-retention temperature. Hence this actinide isotope could fix the timescale for a fast cooling stage, i.e. if the time interval for condensation was about 2 Ma, the 248Cmrecord would be preserved in these early condensations, but if it lasted for tens of millions of years, 248Cm would have completely decayed before it could be incorporated into these minerals. Ozima et al. (1985) have re-examined xenon isotopes produced from the decay of '291 and from 244Puand considered the constraints they impose on the early history of the Earth. The accretion time of planetesimals into the terrestrial planets is of the order of lo7- lo8 years. This is a significant time for the short-lived "'I and 244Pu.While condensation and accretion result in closure of solid elements such as Pu and I, Xe closure might be established only after collisions among planetesimals, since impact shock could result in the effective degassing of volatiles (Lange and Ahrens, 1982). Thus it would be possible for early- and late-accreting material to have significantly different Xe closure times. The excess '29Xe in some terrestrial materials indicates that the region from which it was derived must have been isolated from the atmosphere for nearly the whole history of the Earth. The commonly held view is that this excess lZ9Xeis a result of early mantle degassing (see e.g. Staudacher and AIlCgre, 1982; Allhgre et al., 1983; Hart et al., 1983). Ozima et al. (1985) offer an alternative explanation, viz. that the Earth's inner regions accreted a few tens of millions of years earlier than the outer regions from which the atmosphere evolved. The minimum time interval between the formation of the two regions is of order 1.4 x lo7 years.
2.3.3 Superheavy Elements
Runcorn et al. (1977) and Runcorn (1978) have suggested that superheavy elements (SHE) with atomic numbers between 114 and 126 may be relatively stable and may have provided the early heat source that melted the moon in its first few 100 Ma. They further suggested that these elements may be soluble in iron and hence provide the driving mechanism for the generation of the ancient lunar magnetic field. In a later paper, Libby et al. (1979) suggested
The Origin of the Core
97
that the heavy elements in iron meteorites may be partly the fission products of SHE. Flerov et al. (1977) claim to have observed in carbonaceous chondritic meteorites spontaneous fission of nuclei that they argue are SHE nuclei. However, there is no firm evidence as yet for the existence of relatively stable SHE. Kaiser et al. (1981) carried out a search for any records of fission events in the metal phase of IA and IVB meteorites, and found no evidence in support of a fissionable, siderophile superheavy element; limits for fission events are too low for fission to be a significant heat source in planetary cores. The highest possible value for heat production deduced from their Nd-Sm data in iron meteorites is one order of magnitude smaller than that required to drive the geodynamo by heat release due to radioactive decay (see 94.6). The lower values obtained from Kr, Xe and fission track data are two to three orders of magnitude smaller than the required energy production. Kaiser et al. conclude that nuclear fission could not have contributed significantly as a heat source to drive an early lunar, or a terrestrial, core dynamo.
2.3.4 Adiabatic Compression
The temperature of the material within the aggregating Earth would also increase because of adiabatic compression. Although data (particularly on the variation with pressure of the coefficient of thermal expansion) are rather uncertain, a rise in temperature of several hundred degrees from this source seems possible.
2.3.5 Potential Energy due to the Mutual Gravitational Attraction of the Particles of the Dust Cloud
The kinetic energy of the aggregating particles is either converted into internal energy or radiated away. It is extremely difficult to estimate the contribution from this source because of our lack of knowledge of the physical processes of accretion. The result depends quite critically on the temperature attained at the surface of the aggregating Earth and on the transparency of the surrounding atmosphere to radiation. Comparatively low surface temperatures (of the order of a few hundred degrees) have been suggested, mainly because the atmosphere of the primitive Earth was assumed transparent so that the thermal energy of the impinging particles was immediately re-radiated into space. Ringwood (1960) has argued, however, that during these early years the primitive Earth would have had a large reducing atmosphere. In the presence of these reducing
98
The Earth’s Core
agents (chiefly carbon and methane), the accreting material would be reduced to metallic alloys-principally of iron, nickel and silicon. The outer regions of the Earth would thus be metal-rich and dense (referred to zero pressure) compared with the interior. Such a state is gravitationally unstable and convective overturn would follow, leading to a sinking of the metal-rich outer regions to the centre. This would release further heat due to the energy of gravitational rearrangement. Ringwood believes the whole process is likely to be catastrophic, since the overturn would be accelerated as the initial temperature rose. The relative importance of the gravitational potential energy of the dust cloud as a means of heating the proto-Earth depends critically on the duration of the accretion process-rapid accretion is necessary to produce high temperatures and melt the OC. The rate of growth of mass of the embryo Earth would increase in the beginning of the accretion process (because of the increase in the capture cross-section of the embryo), pass through a maximum and then decrease (because of the exhaustion of accretable material). The law governing the flux, h, of falling matter determines the ultimate thermal profile, since losses by radiation depend upon how fast the recent fall is covered by new layers thus insulating the former from radiative loss. The energy balance is given by the equation T 3
+ CP[T(t)- T&l
for infalling matter having the velocity of escape at impact, where G is the universal constant of gravitation, M ( t ) the mass of the Earth, m the mass flux, r(t) the instantaneous radius of the Earth, p the mass density, E, the emissivity, c the Stefan-Boltzmann constant, T ( t )the instantaneous temperature of the surface of the proto-Earth at time t, To the background temperature of free space of the circumsolar nebula into which radiative losses take place, and cp the specific heat at constant pressure, In (2.1) the term on the left-hand side represents the gravitational energy input, the first term on the right-hand side the radiative loss rate, and the second term the rate of heat takeup by the infalling matter in coming to the temperature T(t).Heat conduction to the interior from the hot surface regions is neglected since it is vanishingly small for time-scales of the order of 103-106years. Heating due to adiabatic compression is also ignored. The mass flux, m(t), is the dominant parameter in calculating the thermal profile resulting purely from accretion, although To has an important effect under certain conditions. In general m = m(t) but, as will be shown later, whether m = m ( t ) or is constant has little bearing upon the main conclusions. It is easy to generalize a set of laws for m that include gravity and slower rates
99
The Origin of the Core
of accretion as well. It can be shown that the exact form of the law has little effect upon the time-limit for sufficient energy to be stored to melt surface or subsurface regions. Write m = c,/r"
where r
= r(t) and c
(2.2)
is a constant with index n. Since M = 47cpr2i, m = h / 4 n r 2 = pi.
Hence from (2.2) and (2.3),
except for the case n = - 1. In this case
For n = 0, m is constant and the radius grows linearly with time while for 1 the growth is slowed. None of these assumptions is especially plausible physically, as the accretion rate should depend upon the gravitational force (n = - 1) or potential (n = - 2), assuming that the escape velocity is not exceeded and an infinite source reservoir is available. For the case n = - 2, (2.1) becomes la>
$ c p G c - 2r4 =
T4 - T:)
+ c pc
-
2r2(T - To)
(2.7)
where the constant c - ~= mf/R: where mf is the mass flux at the termination of growth, r = R,. From (2.5), it then follows that
and the time taken for the Earth to grow from radius, ro, to final radius, Rmis given by
where Ar = r
-
ro. When r
= R,,
(2.10)
100
The Earths Core
For R,/ro = 2, t = p R , / m f which is the same as for the case m = co. Thus the time taken for the Earth to grow from half-radius to its full value under gravitational accumulation is the same as for riz = co. Although the radiative losses depend upon the accretion time, there is not a great difference in the final temperature for these two cases. The effect of heat being admitted to the incoming matter tends to diminish the differences between the different mass laws for k. Without this term in (2.1), the temperature would vary as r for gravitational accretion and be less for cases where n> -2. If all the gravitational energy of accumulation were trapped in the Earth, the first term on the right-hand side of (2.1) vanishes and the resulting increase in temperature AT can be estimated from the equation (2.1 1)
where R , is the final radius. This gives a temperature of the order of 50,000 K. This is the maximum thermal effect of the accretion process-such a hot origin of the Earth would lead to core formation and large-scale differentiation upon accretion (Ringwood, 1966). The minimum thermal effect of the accretion process may be obtained by assuming that the energy released by inelastic collisions of matter falling in from the primordial gas/dust cloud is partially compensated by energy reradiated to space. The equilibrium condition is then given by (2.1) with the last term omitted. If we assume black-body radiation, E, = 1 and the resulting temperatures are minimal. The unknown quantity is i., the rate of accretion. Hanks and Anderson (1969) have considered a number of models. The simplest assumed a constant accretion rate: more plausible models were obtained with accretion rates i = A sin at and i = Ct2 sin y t , where i is zero at r = 0 and r = Rm. The constants A , a, C and y are determined by the final radius R , and t,,,, the total time of accretion. Figure 2.3 shows the radial growth as a function of time for this last model, when t,,, = 1 Ma. It can be seen that it takes 0.3 Ma for the Earth to reach asteroidal size-the rapid acceleration of the accretion process between 0.4 and 0.9 Ma is responsible for the major part of the temperature rise. The accretion rate begins to decelerate significantly only in the last 200 km. Safronov (see, e.g. 1969) and Urey (1962) prefer an accretion time of the order of lo8 years, rather than the very much shorter times advocated by Ringwood (1959, 1966), Hanks and Anderson (1969) and Turekian and Clark (1969). The above calculation ignores the details of each accretion event-an approximation that can only be justified if all the accreting particles are very small compared to the planet. If the terrestrial planets were .formed by accumulation, there must have been impacts involving proto-planetary
101
The Origin of the Core
I
I
I
I
7
5000
"0
0.2 0.4 0.6 0.8 Time of ter accretion begins ( M a1
1.0
Fig. 2.3. Radial growth of the Earth. (After Hanks and Anderson, 1969.)
bodies of many different sizes: the above theory would not simulate the heating from such events at all. Again, this simple theory does not take into account any mass loss by the growing planets during accretion: high speed impacts could cause considerable heating, at the same time ejecting more mass from the forming body than they brought to it. The heating effect of impacts of large falling bodies is considered in more detail in $2.3.8. The accretional heating of terrestrial planets has been reviewed by Ransford (1982).
2.3.6 Dissipation of the Earth's Rotational Energy
As the Earth slows down through tidal interaction with the moon (and to a lesser extent with the sun), part of its rotational energy is dissipated by tides in the oceans and part in the interior of the Earth by Earth tides. It is difficult to estimate how the energy loss is divided between ocean and Earth tidesprobably most of it is dissipated in the shallow seas. If the heat generated by tides were evenly distributed over the whole volume of the Earth, the increase
102
The Earths Core
in temperature would be unimportant (probably less than 100 K). However, if there is a region of low viscosity in the upper mantle, most of the energy of tidal deformation should be dissipated there, resulting in a greater increase of temperature. This would have occurred when the Earth and moon were relatively close together and the Earth’s rotation was much faster than it is now; but even if the moon was once close to the Roche limit, it would recede so rapidly that the effect of tidal heating would be negligible.
2.3.7 The Formation of the Core
If the Earth formed by accretion from approximately homogeneous material and later differentiated into crust, mantle and core, the formation of the core would release a large amount of gravitational energy as a result of the concentration of the high density nickel-iron in the centre of the Earth. Tozer (1965) estimated the increase of heat arising from core formation from an originally undifferentiated Earth to be 470 cal/g. About 6% of this would melt the Ni-Fe phase, while the rest would raise the mean temperature of the Earth about 1500 K. Birch (1965) has made a similar estimate and obtained essentially the same result (400 cal/g) for the energy available for heating. In a later paper, Flaser and Birch (1973) corrected an error in Birch’s original paper. Their revised estimate of the energy release due to core formation is 590 cal/g which would be sufficient to heat the Earth by about 2000 K. Thus the formation of the Earth’s core may well have played a dominant role in the thermal history of the Earth.
2.3.8 Impacts of Falling Bodies
Safronov (1969, 1972, 1978) is of the opinion that one of the main sources of heat for an Earth accreting cold was the impacts of falling bodies. Estimates of the initial temperature from this source depend largely on the body sizes assumed. Calculations based on the assumption that these bodies were small give a low initial temperature-from 300 K near the surface to 800-900 K at the centre. The impact energy of small bodies and particles would be liberated near the surface of the growing Earth, practically all of it being radiated back into space. Safronov believes, however, that relatively large bodies were involved in the formation of the planets, the largest bodies falling on the Earth having diameters of several hundred kilometres. The larger the incident body, the greater the depth at which its impact energy would be released and hence the greater the fraction of this energy that would be trapped inside the Earth, unable to escape into space. Moreover, larger bodies would produce
The Origin of the Core
103
deeper craters, inducing more intensive mixing of the material on impact. Heat transfer by mixing of material during the impact of large bodies is far more efficient than heat transfer by ordinary thermal conduction. Numerical estimates show that the maximum initial temperature of the Earth occurred in the region of the upper mantle (at a depth -500 km) and probably exceeded 1500 K. The largest bodies striking the Earth would also cause primary inhomogeneities in the mantle. Apart from inhomogeneities arising from differences in chemical composition of the impacting bodies, there would also be temperature inhomogeneities. Regions of impact of the largest bodies with sizes up to 1000 km would be additionally heated some hundreds of degrees-in such large areas the temperature would not be equalized even after 1000 Ma. With the additional heat due to radioactive decay, the central zones of these regions would be the first to reach melting temperatures. When about half of the material had melted, local gravitational differentiation would take place-heavy materials would settle down to the lower part of the zone, and light materials rise to the upper part. During such global differentiation large amounts of thermal energy would be released. As a result, a greatly heated vertical column of lower viscosity would be formed along which masses of heavier materials would sink downwards to form the core. Safronov also suggested that it was above such regions excessively heated by impacts that the formation of the continents took place. Safronov’s conclusions were based on an extremely simple model, Kaula (1979) refined the model by treating the thermal evolution of the Earth to be time-varying in a spherical geometry. The energy partitioning at impact was taken from the work of O’Keefe (1977) and O’Keefe and Ahrens (1977), the distribution of impact energy declining with depth. The greatest uncertainty in Kaula’s models is that portion of the impact energy partitioned to internal energy that is retained after material falls back in great impacts. Kaula found that models of the Earth with growth times of the order of 50 Ma became hot enough for vaporization to occur if more than about 12% of the heat energy is retained upon impact. He also showed that early planetary heating is insensitive to planetary growth time-rapid formation is not required. In a later paper, Kaula (1980) re-examined his earlier model and reaffirmed his conclusion that the impact of falling bodies would have led to significant heating, more than enough to trigger core formation. The principal modification from the conclusions of his 1979 paper is that the temperature would never have risen much above melting, since the viscosity of molten material would have been low enough to remove heat as rapidly as it was generated by impacts. The effects of lateral heterogeneity are mainly to promote convection and thus heat removal. Core formation probaby started before the Earth was 10% formed, since melting temperatures would have been reached by
104
The Earths Core
that time. Kaula estimated that the peak energy release was near the MCB, and that about 60% went to the core. The resulting temperature gradient in the mantle was strongly super-adiabatic. The energy released by differentiation of subsequently infalling material would have gone mainly into the mantle, where it would have further contributed to vigorous convection, and not into the core. The calculations of the accretion heating effect by Safronov (1972, 1978) and Kaula (1979, 1980) assumed that there was no overlap between the growth zones of the Earth and Venus during their formation. Wetherill (1976) considered this possibility and also the effect of slightly eccentric orbits for the proto-Earth and proto-Venus, and obtained much higher relative velocities in both the Earth and Venus zones and much larger masses for the planetesimals relative to the proto-Earth and proto-Venus. In this model, both the Earth and Venus and the Moon would have melted completely during accretion. Davies (1985) has discussed in detail the heating of a planet due to the impact of falling bodies. In a growing planet, the heating rate will be greatest at the surface and will decrease with depth. Heat transport back to the surface will also be affected by mixing accompanying impacts and this effect will also decrease with depth. Moreover, the surface of the planet will be moving upwards as new material is added. Relative to the accreting surface, the material is moving downwards. Thus, heat that is deposited too deeply will not be conducted back to the surface before it is carried into the low conductivity interior and there trapped. Davies thus identifies three depth-scales that affect the fraction of deposited heat that is retained in the growing planetthe depth-scales of heat deposition, impact mixing and the ratio u/v where u is the thermal diffusivity and u the upward velocity of the accreting surface. He showed that the efficiency of heat retention is independent of planetary growth rate, and confirmed Safronov’s (1969, 1972, 1978) conclusion that a significant amount of impact energy will be retained in a slowly growing planet. Assuming a heat deposition efficiency of 20%, a terrestrial planet will reach melting temperatures in its outer layers at a radius of between 2000 and 3000 km (see Fig. 2.4). Davies stresses the importance of the correct scaling for impact effects, and questions some of the results of Kaula (1979, 1980) that are inconsistent with the general scaling forms deduced by Holsapple & Schmidt (1982).
2.3.9 Blanketing Effect of a Primordial Dense Atmosphere
Hayashi et al. (1979) considered the heating due to the blanketing effect of a primordial dense atmosphere surrounding the proto-Earth. When the mass
105
The Origin of the Core
1
I
5
I
6 log R (rn)
Fig. 2.4. Temperature profiles for growing terrestrial (rock-iron) planets. Solid lines bound the preferred range corresponding to impactor heating, while short-dashed lines correspond to crater heating. M and E denote momentum and energy scaling, respectively. Long-dashed sloping lines are the limits assuming lOO%-efficient heat retention ( T A ) and 100%-efficient deposition plus