Engineering Data on Mixing by Reiji Mezaki, Masafumi Mochizuki, Kohei Ogawa
•
ISBN: 0444828028
•
Publisher: Elsevier Science & Technology Books
•
Pub. Date: January 2000
Preface This book is a compilation of the engineering data on mixing, which have appeared in the major technical journals of chemical engineering and bioengineering since 1975. That year marked the beginning of a period of rapid advancement in the science and technology of mixing, with rather reliable results for both theoretical and experimental studies. In addition, we have included some important earlier articles which have been and are still being referred to. Mixing is a basic technology important in a wide variety of industries. Many numbers of tanks equipped with various types of agitators have been used for mixing all kinds of materials since ancient times. Yet designs of both agitators and tanks still depend primarily on art and experience. In the light of this fact we felt that the data on mixing should be compiled and presented in a systematic manner for assistance in design and analysis of agitated tanks , and to provide easier access to mixing data for various engineering activities. Of course, computeraided searches of pertinent data bases can be of assistance to chemical engineers and bioengineers in their studies. However, computer surveys of data bases are sometimes timeconsuming and often costly. Furthermore inadequate selection of key words can jeopardize the searches. In view of these objections, we offer this book in the hope that it will be useful to those who desire to conduct an efficient and accurate survey of the mixing data of interest to them. No attempts were made to verify the mixing data given by the various investigators. We have simply indicated the limitations of correlations and data when they are available. The use of uniform units might have been appreciated by users of this book. However, we have elected to use the original units as given by the various authors, lest errors be introduced in the conversion process. In Chapter 1 we present a variety of results for the experimental measurements of flow patterns in stirred tanks. Most of the measurements were made by using modem LaserDoppler techniques. This chapter is useful for the prediction of flow patterns in tanks with many different geometries, various types of agitators, and fluids of diverse physical and rheological properties. Here can also be found valuable data for the validation of results obtained by CFD simulations. Chapters 2 through 5 deal with data for traditional chemical engineering subjects. In Chapter 6 we sununarize a number of scale-up relations developed over the years for various systems. They include liquid, solid-liquid, liquid-liquid, gas-liquid, and solid-liquid-gas systems. Chapter 7 provides data related to multiphase processes. We wish to call attention to two sections: Section 7.4.1 Drop size and drop-size distributions Section 7.4.2 Bubble size and bubble-size distributions These two subjects have not been treated systematically either in text books or in handbooks on stirred-tank mixing, although the results of both experimental and theoretical investigations have been reported on many occasions. Chapter 8 deals with gas-inducing mechanically agitated systems. The applications of this type of agitation system will become increasingly attractivefromthe standpoint of rationahzation of stirred-tank operations as well as environmental protection. A review of this book will reveal many important research subjects that fall in the domain of stirred-tank mixing. We examined over nine hundred technical articles published since 1950. From this activity we could draw two important conclusions: (1) First, about 95% of the results reported in those articles were obtained by employing vessels whose diameters were less than 0.5 m. In industry, vessels with appreciably greater diameters are in daily use, and many more vessels will be designed andfabricatedfor future use. In view of thisfact,much of the accumulated data and associated theory based on small- scale experiments will probably be
VI
inadequate for prediction of the performance of industrial-scale vessels. More data are undoubtedly needed to narrow the gap originating from this mismatch of equipment sizes. More specifically, advanced scale-up techniques, not rules, should be developed for precise prediction. In this respect it would be of great help if industries were cooperative in furnishing unsuccessful, as well as successful, examples of scale-up. (2) Secondly, there is a striking shortage of mixing data for systems in which highly viscous, non-Newtonian fluids are studied. It may be true that conventional agitated tanks are not satisfactory for such fluids. However, the authors of this book feel that many challenges still exist in this area. In this book we have excluded from consideration two important subjects related to mixing: reactions and crystallization in stirred tanks. Most of the articles treating those subjects were found to place more emphasis on the development of rate expressions for the reactions or crystallization. Here, we have aimed to compile data correlating process parameters with agitated-tank geometry and the physical properties of the relevant fluids. For this reason we feel that reactions and crystallization should be treated differently. It should be noted that several important journals issued in Russia, in Eastern Europe, and in the People's Republic of China were not considered in our search for mixing data. This is mainly because of difficulties in obtaining the original journals as well as the Englishlanguage versions. However, the authors sincerely hope that the pubhcation of this book will encourage other interested persons to compile mixing data published in the geographical regions mentioned above. Perhaps in this way some collaborative efforts will result in a substantially more complete compilation of engineering mixing data. It is inevitable that errors, omissions, and misunderstandings will arise in a work of this type. The authors will be grateful if readers would take the time and trouble to point these out to us. The authors would like to thank Professor R. B. Bird of the University of Wisconsin, who aided with advice and suggestions in reviewing and editing the title and preface to this book. Acknowledgment is also made to the staff members of Shinzan Sha, in particular, to Mr. K. Shinoe for his constructive advice during the preparation of the manuscript of this book, and to Ms. H. Tomita for the preparation of the camera-ready manuscript. Without their efforts this book could not have become a reality. August, 1999 Reiji Mezaki Masafumi Mochizuki Kohei Ogawa
Table of Contents
Preface, Pages v-vi Chapter 1 - Flow patterns, Pages 1-84 Chapter 2 - Mixing time, Pages 85-115 Chapter 3 - Power draw and consumption, Pages 117-238 Chapter 4 - Heat transfer, Pages 239-304 Chapter 5 - Mass Transfer, Pages 305-468 Chapter 6 - Scale-up rules, Pages 469-512 Chapter 7 - Other subjects related to multi-phase systems, Pages 513-731 Chapter 8 - Gas-inducing mechanically agitated systems, Pages 733-764 Author index, Pages 765-769
Chapter 1 . Flow patterns 1.1 Single phase Peters, D. C. and Smith, J. M., Ttans. Instn. Chem. Engrs., 45, T360 (1967) Fluid Flow in the Region of Anchor Agitator Blades Experimental apparatus Vessel Type: flat-bottomed Diameter: 12.08 in Height: 18 in Liquid contained Height: 14 in Impeller Type: anchor Width of agitator blade: 1.0 in Wall/blade clearance: runs2A 0.125 in runs2C 0.50 in Working fluids and their physical properties No. ^ (poise) p (g/cm^) 1 lubricating oil 1.5 - 2.5 0.865 2 lubricating oil 0.885 6.8 - 10.4 1.25 3 glycerol (3% water) 5.6 - 9.75 4 silicone oil (MS200) 125 - 131 0.96 0.98 290 ~ 318 5 silicone oil (MS200) n /j(gs" Vcm) p(g/cm^) 0.7 1.01 6 1% polyacrylamide (aq.) 2.12 - 2.57 0.46 - 0.54 7 2% 40.4 - 50.4 1.02 308-460 1.04 0.30 - 0.38 8 4% Reynolds numbers were computed using temperature-corrected viscosity data. F l o w measurement technique Photography 18 1 Results ' 1 ' ' « ' ' ' LJ-' f
Tank: 22.9 cm diameter Anchor: 19.5 cm diameter, 2.5 cm wide, 90 rev/min Fluid: Silicone oils, 60 poise and 180 poise
^^^-^^V^J t-
Velocity components perpendicular to radii, along. normal to, and at 30*^ to agitator blade
Hi)) ^^^Sr/w/y
t«t-
feCX^^^y^vy*!?^^^^
IS^^^^^r^'^^'
Velocity profiles andflowpatterns (Beckner, J. L., Ph. D. Thesis, 1965. University of Wales)
Chapter 1. Flow pattoms
\'-.
X
16 p.p.s. (some points at 8 p.p.s.) NiRe)=21A, Run3-2C-10
y
25.4 p.p.s. (some points at 12.7 p.p.s.) iV(i?«)=105.3, Run3-2C-30
33.4 p.p.s. and 63.4 p.p.s. i\^(/?e)=143.4, Run3-2C-60 Flow patterns with glycerol
1.1 Single phas«
^"
. . .
• . -^A* • .
/f.-
•
r''
*
. >r;*,
7
•..
'.
•M-Ji'.i'V^
•••..
y
.
/ 32.0p.p.s. N*(Me)=l2.9, Run7-2C-40
64.0 p.p.s (some points at 32 p.p.s.) iV*(/?^)=25.5, Run7-2C-80
'- -r - ^-. *
Note: Cxeneralized Reynolds numbers are based on a power law (expression for the shear rate/shear stress relationship as used by Beckner) Flow patterns with 2% aqueous polyacrylamide, 1 in. blade, 0.5 in clearance
/ 64.0 p.p.s (some points at 32 p.p.s.) N*(Jie)=3lA, Run7-2C-100
Notation a geometrical constant c clearance between blades and wall D paddle diameter DT tank diameter k usual power law characterization parameter n usual power law characterization parameter N rotational speed of stirrer p density of fluid /i viscosity of fluid
The normal Reynolds number: NiHe)=N^Dpln The Reynolds nimiber for power-law fluids: N*{Re)=N^~''D^p/[k[a(\-n)Y'\ a=37-120 C/DT
Chapter 1. Plow patterns
Cooper, R. C. and Wolf, D., Can. J. ofChem. Eng., 46,94 (1968) Velocity Profiles and Pumping Capacities for Turbine Type Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 15 in Height: 20 in Baffle Number: 4 Width: IV2 in Impeller Type: 6 and 10 bladed turbines Dimension: Turbine No.
Blade diameter in.
Blade width in.
Blade length in.
No of Blades
1 2 3 4 5 6 7 8 9 10 11 12
3 4 5 6 9 9 4 4 4 4 4 4
0.6 0.8 1.0 1.2 1.8 3.6 0.6 1.0 1.2 1.4 1.6 0.8
0.75 1.0 1.25 1.5 2.25 2.25 1.0 1.0 1.0 1.0 1.0 1.0
6 6 6 6 6 6 6 6 6 6 6 10
Working fluids Water and air Flow measurement technique Hot-wire anemometry and three-directional pressure measurement
1.1 Siiigl* phas«
Results
J
2
.4
.«
.B
LO
Normalized radial velocity profiles for various turbine sizes and various rotational speeds in water.
Notation VR W Z
radial velocity component turbine blade width vertical distance
Radial velocity profiles at different radial distances (4-in. turbine in water).
Chapter 1. Flow patterns
Bourne, J. R. and Butler, H., Trans. Instn. Chem. Engrs., 47, Til (1969) An Analysis of the Flow Produced by Helical Ribbon Impellers Experimental apparatus Dimensions of vessels and impellers Type: flat-bottomed Volume: (1) 6 gals (2) 160 gals Geometry
The geometry of the helicalribbonmixer Summery of principal dimensions Impeller number 1 2 3 4 5
d (in) 10.303 11.030 11.142 11.370 34.34
d D 0.889 0.952 0.962 0.981 0.954
h D 1.06 1.06 1.06 1.06 1.06
W D 0.108 0.108 0.108 0.108 0.104
s D 0.345 0.345 0.345 0.345 0.345
Zo D 1.22 1.2L' 1.22 1.22 1.22
Working fluids and their physical properties Pseudoplastic fluids: aqueous solutions of sodium carboxy methyl cellulose (CMC) and hydroxypropyl methyl cellulose (Celacol) apparent viscosities 1 ~ 500 poise at concentrations up to 3 w/w% and shear rates of 1 3001/s
1.1 Single phase
Flow-measurement technique Observations of solid tracers and cine-photography Results
[T
p0-15
T"
Y
Y U
0-03 L
I
I
1
I
i
A*
xa Y4 4*0 D20
+ 30 X«0
0-15
_
/
/
7
vso 1
1 0-A
i
i 0-6
Is
0-09 h
Y Y Y
/ 1
J ,„-J.,..J
NOTE > No values of r^/Ni bclwtcn 0 ondOOS
X: Howflex SP D:2'95< Celacol
y;2'65%Celacol + :2-3% Celacol A; 2-0% Celacol Y: 1-65% Celacol
The distribution of axialfluidvelocities in the core for impeller 2 pumping upwards
Notation d D h N r Ri 5 Vt W Zo
Y
/
1
outside diameter of ribbon inside diameter of tank height of ribbon rotational speed of impeUer radial coordinate inside radius of ribbon pitch of ribbon axial fluid velocity width of ribbon static height of liquid in tank
1
'i X-t-
i
1
!
r---T— • r - —
0-03
X
V
Y Y
y
20A X40 i^AO 20 XS YCO X20 Y40 Y X O30 SX20 •f20 _ • A80 ^20 Y l AAO O30 o e+goao 3p V, YS X20 •''J, Y20 V«0 O30 V20 30 X a oso aso vioo oso 30o3o ^ 3 0 YIO 030 X20 X20 lOOA S^OW VW 20X O60 vco 0*0 AID
1
1
o-iep-
1
^
yi
Y
\"
Y Y Y Y Y
X
1
-t-
X+ X + XO X \ XX + x \ O x \ + X X X X \ /+ X+ X O X + \ / X X^ X X +X + \ /x+ + X+ X ^ X+ X+ X+ X + X X Xf + Xo X X X+ + X \ o o x+ X X^ O y ^ H -»ox / X
xAxo x j X
/
X
\ "H
Y x^l y / V/ X X
z/
X
H
\
\
. .
J 0-A
l_ . 1 0-6
1
J
_LAI
+ : impeller I X: impeller 2 o: impellers
The distribution of axialfluidvelocities in the core for impeUers 1,2 and 5 (6 gal and 160 gal tanks) pumping downwards
Chapter 1. Flowpatt«ms
Takashima, I. and Mochizuki, M.J. Chem. Eng. Japan, 4,66 (1971) Tomographic Observations of the Flow Around Agitator Impeller Experimental apparatus Vessel Type: flat-bottomed Diameter: 450 mm Height: 600 mm Liquid contained Height: 520 mm Baffle Number: 4 Width: 45 mm Impeller Type: radial flow turbine Diameter: 150 mm Number of impellers: 1 Number of blades on impeller: 8 Width of impeller blade (parallel to shaft): 34 nun Off-bottom clearance: 260 mm
Results
Flow profile in each sectional zone of various types of 8 blades turbine agitator
1.1 Single phas«
Double helical flow model for agitator blade Notation u tangential velocity at blade tip V absolute velocity of flow observed on the fixed coordinate Vr radial velocity of flow w relative velocity of flow observed on the rotating coordinate *P angle of the blade (see attached figure) Fb circulation of bound vortex around the blade 0 Vr/u flow coefficient CD angular velocity of impeller Subscript 2 outer point of flow from the impeller
Chapter 1.
10
Flow patterns
Murakami, Y., Fujimoto, K., Shimada, T, Yamada, A. and Asano, K.,/. Chem. Eng. Japan, 5,297 (1972) Evaluation of Performance of Mixing Apparatus for High Viscosity Fluids Vessel and impeller geometry
Impellers and vessels (a) anchor (b) paddle (c) helical ribbon (d) mixing apparatus with two agitator axes having multidisks Z>=12.2cm, H=D, rf=0.90D and 0.95A 6=0.1Z), 1)^=6.0 and 9.0 cm, /=0.5/)rf and 0.22Drf
Working fluids and their physical properties Liquid: aqueous solutions of com syrup Viscosity: about 200 poise
Flow measurement technique Photography
Results
t " II h t It I
0
0.5
h I i i I MM I 0 0.5 1.0
1.0
--*' V Q
XTTnd
*"•* V Q
Anchor-tangential velocity ll-H' RE - 0.07
11
[ol 1
j
XjlfUlDK
Sg
• /S>KP1 /"^ W?nfK 1
^Tind
Paddle-tangential velocity
Lfflll^
I
0 0.5 1.0 "adn
Helical ribbon (velocity profiles)
1.1 Single phase
11
Mixing apparatus with two agitator axes having multidisks (velocity profiles at a section 6 mm apartfromthe disk at 15 mm space intervals) ^CIRCULAR ANNULUS . KEILSPALT MASCHINEN CIRCULAR ANNULUS (ROTATING CYLINDER) ECCENTRIC
CYLINDERS
HELICAL RIBBON WITH SCRAPE MIXER WITH TWO AGITATOR AXES HAVING DISKS
|CL>
s
EXTRUDER
Q
\ -
C & R REACTOf ELICAL SCREki (NAGATA)
HELICAL SCREW (GRAY)
0.01 0.02 0.0^
0.1
1 -K , C / D ,
0.2 I/D^
Shear characteristics
Notation b blade width of helical ribbon, cm d impeller diameter, cm D vessel diameter, cm Dd disk diameter, cm gr gravitational conversion factor, g cm/G sec^ / distance between disks, cm n rotational speed, 1/sec Pv power consumption/unit volume, Gcm/seccm^ Vb, V2 tangential and axial velocity, cm/sec 77 liquid viscosity, poise K ratio of impeller diameter to vessel diameter
Chapter 1. Flow pattoms
12
Ito, S., Ogawa, K. and Yoshida, N.,/. Chem. Eng. Japan, 8,206 (1975) Turbulence in Impeller Stream in a Stirred Vessel Experimental apparatus Vessel Type: flat-bottomed Diameter: 312 mm Liquid contained Height: 312 mm Baffle Number: 4 Width: 10.4 mm Impeller Type: a standard six-bladed turbine Diameter: 104 nmi Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): 26 nrni Width of impeller blade (parallel to shaft): 20.8 nmi Off-bottom clearance: 156 mm Working fluids and their physical properties an aqueous solutions of K4Fe (CKk and KaFe (CN)6. The kinematic viscosities of the solutions are the same as that of water Flow measurement technique Measurement of diffusional mass transfer rate using a multi-electrode Experimental conditions Impeller speed: 60,90 and 120 rpm Results
Notation r_ radial position, mm Ui mean velocity of i component, cm/sec UT impeller tip velocity, cm/sec 2 axial position, mm
65
75
85 95 105 r, mm
Turbulence intensity
Subscript r, z, G radial, axial, tangential component
t15
125
1.1
13
Van't Riet, K. and Smith, J. M., Chem. Eng. ScL, 30,1093 (1975) The Trailing Vortex System Produced by Rushton Turbine Agitators Experimental apparatus Vessel Type: flat-bottomed Diameter: (1) 44 cm (2) 120 cm Baffle Number: 2 Impeller Type: six-bladed disc turbine Diameter: (1) 17.6 (2) 48 cm Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): Z)/4 Width of impeller blade (parallel to shaft): D/5 Working fluids and their physical properties Fluid: tap water and water/glycerin solutions Tracer: polystyrene particles (diameter 0.5 mm) Flow measurement technique Photography Experimental conditions Direction of Impeller speed: 5 rps Results
rototion
Schematic thee dimensional view of the trailing vortex pair.
Dirtetion
Schematic two dimensional view of theflowin the stirrer blade region. S, stagnation point.
Chapter 1 . Flow patterns
14 , Blode
>^
500
A/ff,«300
The vortex axis position at different iV)?,. ' ' '1
\
I
»
^ l-5xlO*
/V/?,*500 lOh
0
%5-300 Slopc-2
o
\ %
I .1 (A
c E o J I I I -1 M I I I 10 05 Dimensionleis rodius from vortex axis. r/Oin\0
Notation D stirrer diameter, m N stirrer speed, 1/sec NRt Reynolds number, pND^/j], dimensionless r radial distance, m 7} dynamic viscosity, Nsec/m^ p density, kg/m^ (o angular velocity, 1/sec
The dimensionless angular velocity distribution. # , Averages for 1.5X 10^< NR, > 9 X 10^; O, Measuring points for 7V)?,=300 ; Z)=17.6cm
1.1 Single phase
15
Gunkel, A. A. and Weber, M. E.,AIChE Journal, 21,931 (1975) Flow Phenomena in Stirred Tanks Part I. The Impeller Stream Experimental apparatus Vessel Type: flat-bottomed Diameter: 45.7 cm Height: 45.7 cm Baffle Number: 4 Width: 0.17 Impeller Type: standard six-bladed disk turbine Diameter: 22.8 cm Number of impellers: 1 Number of blades on impeUer: 6 Length of impeller blade (perpendicular to shaft): //Z)=0.25 Width of impeller blade (parallel to shaft): w/D=0.2 Off-bottom clearance: T/2 Working fluid Air Flow measurement technique Hot-wire anemometry Experimental conditions Impeller speed: 200,400,600 and 950 rpm ^^ Results 10
10"
10' ^4-400 rpm, s - l c m , z-0 . O-O 10"' N-800rpm, s-7cm^ 2-0
,
0-0
10" ' N-600rpm, s - 1 cm.
Notation D impeller diameter E,(n) one-dimensional energy spectrum in the frequency space I length of impeller blade n j&requency N rate of rotation of impeller T tank diameter w impeller blade width
2—0.5 In
,0-0
10 N - 2 0 0 r p m , $-1cm, 2-0 10-
^ 0-43'
probe in vertical plane
10
23468
10"
lrf
10^
10^
10*
n (H2)
One dimensional energy spectra in the impeller stream.
Chapter 1. Flow pattoms
16
Hiraoka, S., Yamada, I. and Mizoguchi, K.,/. Chem. Eng. Japan, 12,56 (1979) IWo Dimensional Model Analysis of Flow Behavior of Highly Viscous Non-Newtonian Fluid in Agitated Vessel with Paddle Impeller Dimension of vessel and impeller 0.3 ^d/D< 0.9 Computational conditions 10 < Re {=^DVp/fi) Computational results d/D > 0.5
n «o.e Rcf 0
(p/>*.v)
Non-Newtonian viscosity distribution for paddle of rf/2>=0.5
Notation Non-Newtonian viscosity distributions for different size impellers d impeUer diameter, m D vessel diameter, m K fluid consistency, k g / m (sec)^"** ^-^mv/DT I {(cDw+2)}.N J n flow behavior index J? radial coordinate, m Re Reynolds number, DVp/fi, dimensionless V rotational velocity of vessel wall, m / s e c Superscript p non-Newtonian viscosity, N s e c / m ^ — averaged value /Xar apparent viscosity, N s e c / m ^ Subscript ft* dimensionless non-Newtonian viscosity, fi/po, NN non-Newtonian fluid dimensionless N Newtonian fluid p fluid density, kg/w? w vessel wall (o dimensionless vorticity
^^^\w^^m^
1.1 SingI* phase
17
Kuriyama, M., Inomata, H., Aral, K. and Saito, S.,AIChEJoumaU 28,385 (1982) Numerical Solution for the Flow of Highly Viscous Fluid in Agitated Vessel with Anchor Impeller Experimental apparatus Vessel Type: flat-bottomed Diameter: 128 mm Liquid contained Height: 128 mm Impeller Type: anchor Diameter: about 128 mm Height: 115 mm Number of impellers: 1 Working fluids Aqueous solutions of com syrup containing solid-particles as tracers Flow measurement technique Photography Experimental conditions Results
i.. •
: C«tcuUt«d : ExptrimtnUI
Tangential velocity distributions (Be = 1)
Notation d impeller diameter N rotational speed of impeller U, V velocity components VB tangential velocity of blade tip Re Reynolds number, d ^Nl v, dimensionless V kinematic viscosity
(K
07 r/R H
0.91.0
—: CatcuUted • :Exp«rim«nU( Radial velocity distributions {Re = 1)
Chapter 1. Flow patterns
18
Mochizuki, M. and Takashima, I., Kagaku Kougaku Ronbunshu, 8,487 (1982) The Flow around Turbine Type Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 450 mm Liquid contained Height: 450 mm Impeller Type: six-bladed disk turbine Diameter: 225 mm Disk diameter: 150 mm Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): 56 mm Width of impeller blade (parallel to shaft): 28,46,56, 75, and 112.5 mm Off-bottom clearance: 225 mm Working fluid Tap water Flow measurement technique Photography Experimental conditions Impeller speed: 62.5 and 99.4 rpm Results r y piong
V,
V,
Velocity diagram of theflowaround impeller
1.1 Single phas«
19
2/D Part0 0.250 j 0235
,
(2) 1 r
®
O T-n «-
T~l r
I
T~1 r^ T
^-h
^^
^9
upper edge btade
f"
4
•f^f
B/Ort/2
Center of 0
lil L 10
j<JiJ
i_ai L_ 0
^0
0
10
0
10
J 0
1-0
L. 0
10
B/0^1/5
B/DrI/8
Velocity profiles at impeller tip
Tomograms with rotating cameraB/D=l/5, 62.5 rpm
Notation B width of impeller blade D impeller diameter U2 tangential velocity V absolute velocity of flow z vertical distance along z-axis 0 normalized velocity, v/u2 (p angle of polar coordinate Q)
angular velocity of impeller
Subscripts 1 inner area of impeller 2 outer area of impeller 3 top and bottom area of impeller r radial component z axial component (p tangential component
Chapter 1. Flow patterns
20
Mochizuki, M. and Takashima, L, Kagaku Kougaku Ronbunshu, 10,399 (1984) Distribution of Pressure on the Surface of Blade of Turbine Impeller Experimental apparatus Vessel Tjrpe: flat-bottomed Diameter: 450 mm Liquid contained Height: 450 mm Baffle Number: 4 Width: 45 mm Impeller Type: six-bladed disk turbine Diameter: 225 mm Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): 56 nmi Width of impeller blade (paraUel to shaft): B/Z)=l/2,1/5, and 1/8 Off-bottom clearance: 225 mm Working fluid Tap water Flow measurement technique Visualization Experimental conditions Impeller rotational velocity: 82,104 and 106 rpm
Results
Notation B width of impeller blade, m D impeller diameter, m N impeller rotational speed, 1/min
Sock surface
!cl B/D»1/8
Front surface
N*106rpm
Visualization of flow on the surface of blade with oil film method
1.1 Single phase
21
Kuboi, R. and Nienow, A. W, Chem. Eng. Sci., 41,123 (1986) Intervortex Mixing Rates in High-Viscosity Liquids Agitated by HighSpeed Dual Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.29 m Liquid contained Height: 0.29 m Impeller Type: (1) angled blade (2) disk turbine Number of impellers: 2 Number of blades on impeller: (1) 6 (2) 6 Ct>N
i> Boffins. 0-lT. 6 Blodts
JL
45»
T^
0/5
:s].
,x
-*4DMI
HD»T/2 H l|
MA OH T 6 Blodts
T-0-29in
A schematic diagram of the equipment.
Working fluids, their physical properties and experimental conditions Physical properties and experimental conditions (a) Tunnel G140 com syrup/saturated benzoic acid (mass ratio = 5.7:1) p =1,347 kg/m^ n =1.00 Pas (221C): ^ =1.35 Pas (20^:) Re range: 70^140; speed range =3.3—6.7 rev/s (b) 0.30% by wt Goodrich Carbopol in water (pH 4.4) p =1,000 kg/m', T =22.27°-^ ; Ui=1.54r°" ; To=20.0 Pa Re range: 85 ~ 150 ; speed range=6.3-^7.5 rev/s (c) 1.4% by wt Hercules 7H4C CMC in water (neutral) p = 1,000 kg/m', T= 12.2 f"^; t;i=9.82r'' Re range: 72^190; speed range=4.3~8.0 rev/s Flow measurement technique Photographs of solid-particle tracers
22
Chapter 1. Plow patterns
Results
Flow patterns with com syrup: (a) upward pumping combination (5 rev/s); (b) downward pumping (three gross vortices (3,33 rev/s)); (c) downward pumping showing the additional fourth small vortex (5 rev/s)
Notation Cb Ci impeller clearance above the base, m D impeller diameter, m H liquid height, m T tank diameter, m
Flow patterns with Carbopol: (a) upward pumping combination (5.3 rev/s); (b) downward pumping combination (5.3 rev/s)
1.1 Single phas*
23
Yianneskis, M., Popiolek, Z. and Whitelaw, J. E.J. Fluid Mech., 175,537 (1987) An Experimental Study of the Steady and Unsteady Flow Characteristics of Stirred Reactors Experimental apparatus Vessel Type: flat-bottomed Diameter: 294 mm Liquid contained Height: 294 mm Baffle Number: 4 Width: 27 mm Impeller Type: six-bladed disk impeller Number of impellers: 1 Number of blades on impeUer: 6 Dimensions: Diameter Disk diameter Impeller mm mm r/4 73.5 55.12 r/3 98.0 73.5 147.0 110.25 TI2
Blade width mm 14.7 19.6 29.4
Blade length mm 18.37 24.5 36.75
Off-bottom clearance: 7/4, 7/3 and 7/2 Working fluid Water Flow measurement technique Laser-Doppler anemometry Experimental conditions Temperature: 20 ± 2*C Impeller rotational speed: 300 rpm Results
Flow visualization at d =42.5''; (a) i>=r/3, C=r/2, N=3Q0 rpm. (b) />=r/3, C=r/4, Ar=300 rpm
Notation T cylinder diameter, nmi
(a)
(b)
Chapter 1 . Flowpatt«ms
24
Kamiwano, M. Saito, E and Kaminoyama, M., Kagaku Kougaku Ronbunshu, 14,316 (1988) Flow Pattern and Apparent Viscosity of Pseudo-plastic Liquid in a Stirred Experimental apparatus Vessel Type: flat-bottomed Diameter: (1)0.1 (2)0.2 (3)0.3 (4) 0.4 m Liquid contained Height: (1)0.1 (2)0.2 (3)0.4 (4) 0.4 m Impeller Type: six-bladed flat turbine Diameter: (1) 0.05 (2)0.10 (4) 0.20 m (3)0.15 Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: (1)0.05 (2)0.10 (3)0.15 (4) 0.20 m Working fluid Pseudoplastic: 1.2 wt% aqueous solution of hydroxyethyl cellulose Experimental conditions Rotational speed of impeller (1/sec) (1)16.7 (2)6.88 (3)4.03 (4)2.72 Flow measurement technique Image sensor velocimetry Results
-I 1.4
V-2 <|l.O^
-Q05
-01
Q05 (a) V, component
(b) lit component
(a) Vr component
(b) Vet component
Distribution offlowvelocity expressed by threedimensional components (D=0.2m, it =6.88 s *)
Distribution offlowvelocity expressed by threedimensional components (D=0.2 m, «=6.88 s *)
1.1 S i n g I * phas«
25
Cenler axis of vessel blade
0
a: [-{U
k » \
V V ... _
-0.6
[ {:=: (c) Vt component Distribution offlowvelocity expressed by three-dimensional components (Z>=0.2 m, n=6.88s~*)
Notation D vessel diameter, m n impeller rotational speed, 1/sec R radius of vessel, m V flow velocity, m/sec Z height of vessel, m Subscript r, 9t, z
axes of cylindrical coordinate
-R=0.lVBottom o( vessel 0.5 m/5
Flow pattern represented by dimensional vector in r-z plane (D=0.2 m, «=6.88 s"*)
Chapter 1. Flow patterns
26
Winardi,S., Nakao, S. and Nagase, Y.,/. Chem. Eng. Japan, 21,503, (1988) Pattern Recognition in Flow Visualization around a Paddle Impeller Experimental apparatus Vessel Type: flat-bottomed Diameter: 460 mm Liquid contained Height: 400 ram Baffle Number: 4 Width: 40 mm Impeller Type: four-bladed paddle impeller Diameter: 160 mm Number of impellers: 1 Number of blades on impeller: 4 Width of impeller blade (parallel to shaft): 40 mm Off-bottom clearance: 200 mm Working fluid Water Flow measurement technique Photography Experimental conditions Impeller rotational speed: 120 rpm Results
//
x>-. \ .
-- .
Lli "^^
--
4
Icl ; »''
**••" \\i....
I
! I i
"^—1«
: J 5 \ \m.y' / I I-jJ / •
J
rrtS
I
...^^
(a) Discharge pattern, TD (b) Cross pass pattern, TP; x mark indicates disappearance of a particle from the impeller (c) Asymmetric Discharge patten, UD (d) Illustration of Weak Discharge patten, WD (e) Illustration of Weak Cross-pass patten, WP
1.1 Single phas«
27
Komori, S. and Murakami, Y.,AIChE Journal, 34,932 (1988) Turbulent Mixing in Baffled Stirred Tanks with Vertical-Blade Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.29 m Height: 0.7 m Liquid contained Height:/) and 2Z) Baffle Number: 4 Width: 0.029 m Impeller Type: four-bladed paddle Diameter: 0.145 m Number of impellers: 1 and 2 Number of blades on impeller: 4 Blade width: 0.029 m Blade thickness: 0.003 m ^^o^P A B C D E
S H H=2D H=2D H=2D H=^D H=D
im^ers 2 2 1 2 1
Working fluid Water Flow measurement technique Laser-Doppler velocimetry Experimental conditions Impeller speed: 60,120 and 150 rpm
^/^ 0.14--1.70 1.0 0.10-0.60 z
^-/^ 1.0 - 0.5L/Z) 0.06-0.90 0.10-1.50 0.5 (1.0 - 0.5L/Z)) 0.06 - 0.90
Chapter 1 . Flow p a t t o m s
28
Results 0.004
2S0 Afl-2.0s'^ on»1.0s*^ 200
O.OOC
o *- 150
L/0-0.2
tlg/D*1.0 1/0-0.3 VI>*^-2 hj,/0«0.425 ^
100
0.001 J 0.01
0.02
50h O
O
OL (Al
(Bl (C) (0) CxpertaenUI Group
0.04 ^0.0« ^0.08 0.10 0.20
(CI
Maximum (highest) mixing efficiency and minimum energy consumption for each experimental group
1 . * » . l I:..**-"*.Ill
3,..«V«*>N^^^I
];.......—;;] a::::!!" -*•
\3:»r»»«....,,. ''"-'ii j.'.*.»%*«...,^,.
in • e.i V D • 0.7
Velocity vectors and flow patterns in a double-impeller tank, H-2D, «=150 rpm (group A) (a) with lowest mixing efficiency, (b) with highest mixing efficiency
1.1 Single phase
29
Velocity vectors andflowpatterns in a double-impeller tank, H=2D, «=150 rpm (group B) (a) with lowest mixing efficiency, (b) with highest mixing efficiency 1 1 1 [ 1 11 i 11111 1 1surtlng Point il 11 {11 i 1 JJWHTTI
'i 11 ^n i 1 i 1 ^ij i 1 il LTI1111 (IIX1
'ft/ SMK
'1 W w iVw mII 1 111iII11 i1111 ;[illlJIJ||||/|| TTTrTTT^MTtvn
jJflTjT
m
•lii'inuiiii^i •llliSlllllli:!!
lUifmTmil^
PW™ iJirm]
1
j 1111 [ I TTl [TtJ 1
!| 1 1111 111 111 I'l ill J1 1111111 1M 1 III \TI\
3 m l
J^illJITriTnfllll iJinJIjLH
Tracer traveling path and lattices which indicate velocity-measiuement points in a double-impeller tank, H==2D, n=150 rpm (group A)
Notation D Ettox hb H L n P' 6 P- 6mn
tank diameter maximum value of mixing efficiency vertical distance between bottom of a tank and center of lower impeller water depth vertical distance between double impellers impeller rotational speed energy consumption minimum value of energy consumption P- 6
Chapter 1 . Flow patterns
30
Wu, H. and Patterson, G. K., Chem. Eng. Scu, 44,2207 (1989) Laser-Doppler Measurements of Turbulent-Flow Parameters in a Stirred Mixer Experimental apparatus Vessel Type: flat-bottomed Diameter: 27 cm Height: 27 cm Liquid contained Height: 27 cm Baffle Number: 4 Width: lO/T Impeller Type: six-bladed disk turbine Diameter: 9.3 cm Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): D/4 Width of impeller blade (parallel to shaft): D/5 Off-bottom clearance: T/3 Working fluid Water Flow measurement technique Laser-Doppler velocimetry Experimental conditions Impeller speed: 100, 200 and 300 rpm Results 200 rpm r(cm) D 50 o 6.0 A 7.0 • 7.7 0 90 V J0.5
1 ))J3
•^•v>
>
I
>
I
0.1
02
0.3
0.4
09
0.$
07
08
Ua/U,ip
Mean radial velocity profiles at various radial positions.
Mean tangential velocity profiles at various radial positions.
1.1
Single phase
31 -T-
-r-
-r-
r»5cm total random O O too rpm
-^V,o
-0.05
0.00
0.05
0.10
0.15
0.20
000
Mean axial velocity profiles at various radial positions,
0.00
0.05
0.10
0.15
020
025
Profile of tangential turbulence intensity near the impeller tip.
0.30
0.05
0.iO
015
0.20
impeller diameter radical coordinate tank diameter fluctuation velocity mean velocity impeller tip velocity impeller blade width axial coordinate
0.30 0.35 Ur'/Uiip
Profile of radial turbulence intensity near the impeller tip.
055
0.00
0.05
0.10
015
020
025
030 035 u;/u,ip
Profile of axial turbulence intensity near the impeller tip.
Notation D r T u U Uiip w z
025
1 Subscripts r, 6,2 radial, tangential, axial 1 Superscript root-mean-square value
Chapter 1 . Flow patterns
32
Ranade, V V and Joshi, J. B., Ttam. Instn. Chem. Engrs., 68, Pirt A. 19 (1990) Flow Generated by a Disc Turbine: Part I Experimental Experimental apparatus Vessel Type: flat-bottomed Diameter: 300 and 500 mm
Baffle Number: 4 Width: r / 4
Impeller Type: six-bladed disc turbine Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: H/2 Vessel Impeller diameter, diameter, Z), nmi r, mm 300 100 500 168
Disc diameter,
Disc thickness,
Blade thickness.
mm 67 117
mm 2.7 3.7
mm 2.0 2.7
Blade width=i)/5. Blade length=Z)/4. Hub diameter=25 mm. Hub height=25 mm. Shaft diameter=19 mm.
Working fluid Tap water Flow measurement technique Laser-Doppler anemometry Results
0
0*1 0*2 0*1 0*4 0*1 0«l 0*7 0*t 0*1 OIMCMSIONLESS RAOIAL COOHOINATE , ( r- R,)/(l^fl, I
!•(
Radial profile of maximum mean radial velocity in the impeller stream.
1.1 Single phase
Curve
33
Reference
1 2 3 4 5 6 nt work
T mm 292 381 290 1,000 270 89 300
D mm 101.6 101.6 96.7 333.3 93.0 30.4 100.0
Measurement Technique Streak photography Hot wire anemometer Laser Doppler anemometer Hotfilmanemometer Laser Doppler anemometer Laser Doppler anemometer Laser Doppler anemometer
1. Cutter, L A.. \9&I,AIChEJ, 4:485. 2. Cooper, R. G. and Wolf, D., 1968, CanJCkem EngScu 46:96. 3. Van der Molen, K. and Van Maanen, H. R. E., 1978, Chem Eng Sci, 33:1161. 4. Drbohlav, J., Fort, L, Maca, K. and Placek, J., 1978, CoU Czech Chem Commun, 43:3148. 5. Wu,. H. and Patterson, G. K., 1987. Private Communications. 6. Chen, K. Y, Hajduk, J. C, and Johnson, J. W. 1988, Chem Eng Commun, 72:141.
0»%
0*2 0«} 0>4 0*f 0«« ••? 0*ft OtMCHSIOMLKSS RADIAL COOHOINATE f r - l t | ] / | l | . f l , |
Radial profile of maximum mean tangential velocity in the impeller stream.
Notation D impeller diameter, m H height of vessel, m N impeller rotational speed, 1/sec Q flow rate, mVsec r radial coordinate, m R tank radius, m Ri impeller radius, m T tank diameter, m U mean velocity, m/sec Utip impeller tip velocity, m/sec V tangential mean velocity, m/sec 2 axial coordinate, m
0 0.1 0-2 OO 0*4 0*S 0*1 MMCNStOflLESS RADIAL COORDINATE (r-R||/(R-R|)
Radial profile of radial pumping capacity.
Chapter 1. Flow pattoms
34
Kaminoyama, M., Saito, F. and Kamiwano, M.J. Chem. Eng. Japan, 23,214 (1990) Flow Analogy of Pseudoplastic Liquid in Geometrically Similar Stirred Vessels Based on Numerical Analysis Experimental apparatus Dimensions of vessel and impeller Vessel type: flat-bottomed Baffle: non-baffle Impeller: (1) six-bladed turbine Number of impeller: ( 1 ) 1
(2) paddle (3) anchor (2) 1 (3) 1 onolysed region
analysed region
'fh d/DaO.5 H/D-1.0 H/D=0.5 bw/D=OJ bl/D=0.125 ds/O = 0.0^
.Ks21 H/D«1.0 h 70=0.5 ds/0 = 0.0^
P-j (a) onolysed region
Ks20
Ksit
I• 112
d/DsO.9 H/0=:1,o bwl/DsO.l bvv2/D=0l tt»'2 ds/DsQ.O^
Schematic diagrams of mixers and analyzed regions: (a) turbine impeller mixer; (b) paddle impeller mixer; (c) anchor impeller mixer
1.1 Single phase
35
Working fluid A highly viscous pseudoplastic Ellis liquid Computational results
1t
shofl
vessel wall
impeller
O.Sm/5
J=l
I.OwA
J=A (a)
K=n
K= l (b)
Velocity vector distributions in turbine mixer (Z)=0.2m,«=3.33s"'): (a) on r-z plane a t / = l and 4; (b) on r-0 plane at/C=l and 11
Velocity vector distributions in paddle mixer (Z>=0.2 m, «=3.33 s *): (a) on r-z plane a t / = l and 4; (b) on r-d plane at ^=11 and 21
Chapter 1 . Flow patterns
36
Velocity vector distributions in anchor mixer (Z)=0.2 m, «=0.83 s *): (a) on r-z plane a t / = l , 5 and 9; (b) on r-0 plane at/C=l, 11 and 20
Notation hi blade length bw blade width impeller diameter d ds shaft diameter D vessel diameter h impeller height (off-bottom clearance) H liquid height / mesh number in Q direction K mesh number in z direction 0) rotational speed
1.1 SingI* phase
37
Jaworski, Z., Nienow, A. W, Koutsakos, E., Dyster, K. and Bujalski, W, Trans. Instn. Chem. Engrs., 69, P^t A, 313 (1991) An LDA Study of Turbulent Flow in a Baffled Vessel Agitated by a Pitched Blade Turbine Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.146 m Liquid contained Height: 0.146 m Baffle Number: 4 Width: T/10 Impeller Type: 45° pitched bladed turbine Diameter: T/3 Number of impellers: 1 Number of blades on impeller: 6 Projected height of impeller blade: D/5 Off-bottom clearance: 7/4 or T/2 Working fluid Water Flow measurement technique Laser-Doppler anemometry Experimental conditions Impeller speed: 101/sec Temperature: 20°C Reynolds number: 24,000 Results Notation C impeller off-bottom distance, m H liquid depth in vessel, m R dimension less radial coordinate T vessel diameter, m V dimensionless mean velocity V dimensionless r.m.s. fluctuating velocity Z dimensionless axial coordinate Subscripts R radial component RZ dimensionless resultant for (r-z) Z axial component
Dimensionless velocity profiles for C/H=l/4: (a) VR against Z ; (b) Vz against R.
33
Chapter 1. Flow patterns
Dyster, K. N., Koustakos, E., Jaworksi, Z. and Nienow, A. W, Trans. Instn. Chem. Engrs., 71, P ^ A. 11 (1993) An LDA Study of the Radial Discharge Velocities Generated by a Rushton Turbine: Newton Fluids, J?e > 5 Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.150 m Liquid contained Height: 0.150 m Baffle Number: 4 Width: r / 1 0 Impeller Type: six-bladed Rushton turbine Diameter: T/3 or T/2 Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): D/4 Width of impeller blade (parallel to shaft): D/5 Off-bottom clearance: T/2 Working fluids and their physical properties ^, J ^*"^^ Water Polyethylene glycol Glucose solution Glycerol solution 100% Glycerol
Refractive Index 1.333 1.359 1.475 1.457 1.471
Density (kg/mO 1,000 1.064 1,330 1,260 1,260
Viscosity (Pasec) 1X 10~^ 8.85 X10"^ 105x10^ 0.248 1.16
Flow measurement technique Laser-Doppler anemometry Experimental conditions Impeller speed: 50 -^ 800 rpm Results <5: correlating parameter V;/V,ip = 0.454 - 0.128 (r/i?) Notation D impeller diameter, m N impeller rotational speed, 1/sec r radius of measurement point, m R impeller radius, m T tank diameter, m Vr radial component of fluid velocity, m/sec Vtip impeller tip speed, TTND, m/sec
Superscripts ' root mean square value — time average value
1.1 Single phase
39
Mishra, V R and Joshi, J. B., TVans. Instn. Chem. Engrs., 71, ftirt A. 563 (1993) Flow Generated by a Disk Turbine; Part III: Effect of Impeller Diameter, Impeller Location and Comparison with Other Radial Flow Turbines Experimental apparatus Vessel Type: flat-bottomed Diameter: 500 mm Liquid contained Height: 500 mm Baffle Number: 4 Width: r/10 Impeller Type: the standard disc turbine (DT), a straight blade turbine (SBT), a curved blade turbine (CBT), a modified disc turbine (MDT), and a Brumagin impeller (BT)
Y
J 0 /«-
0/5
l^o/*-J (•)
DISC TURBINE ( O T )
— llOnim —
f atmn
\
-IT-
Mrnm-A
TLI^
1*31
BRUMAGIN IMPELLER
(0
-1 •-S2mm •«{ EMO VIEW
gyeVATIpN
PERSPECTIVE VIEW
(b)
r« tt.Siniii
MODIFIED DISC TURBINE (MPT) (d)
<«>
CURVED BLADE TURBINE I C B T )
STRAIGHT BLADE TURBINE ( S B T )
Various designs of radialflowimpellers.
Chapter 1. Flow patterns
40
Impeller design details Impeller Name DT125
DT DT250
MDT Brumagin
CBT SET
figure
Impeller diameter
i.d.
Hub details o.d.
height
No. 2a 2a 2a 2b 2c 2d 2e
mm 125 167 250 167 167 167 167
mm 16 16 16 16 16 16 16
mm 25 25 25 25 36 25 25
mm 26 26 26 25 28 25 50
Blade width
Blade height
Blade thickness
mm 32 42
mm 24 34 50 38 34 34 34
mm 2.0 2.0 2.0 1.5 3.0 2.5 2.0
62.5
52 35
71
Off-bottom clearance: DT HI2, H/3, and H/A, all other impellers H/2 Working fluid Water Flow measurement technique Laser-Doppler anemometry Results
UO ISO ISO RADIAL 01 STANCE,r(mmI
(a)
(b) Radial velocity at the impeller centerline.
Notation H liquid height, m r radial coordinate, m T vessel diameter, m U mean radial velocity, m/sec Vt impeller tip velocity, m/sec Z axial coordinate, m
210
1.1 Single phase
41
Mishra, V R and Joshi, J. B., Trans. Instn. Chem. Engrs., 72, Part A. 657 (1994) Flow Generated by a Disc Turbine: Part IV: Multiple Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.3 m Liquid contained Height: 1.57 Baffle Number: 4 Width: 0.1 T Impeller Type: a standard disc turbine (DT) and a pitched blade downflow turbine (PTD) Diameter: DT 100 nun; PTD 100 mm Number of impellers: 2 Configurations of impeller combinations. IC (xn)
C (m)
0.05 0.1 0.1 0.1 0.15 0.225
0.2 0.1 0.15 0.2 0.15 0.112
Name of the configuration DT-DT
DT-PTD
DDl DD2 DD3 DD4 DD5 DD6
DPI DP2 DPS DP4 DP5 DP6
Working fluid Water Flow measurement technique Laser-Doppler anemometry Experimental conditions Impeller speed: 5 rps Impeller Reynolds number: 6.25 x 10^ Power number,flownumber, hydraulic efficiency of multiple disc turbine impellers. Clearance Clearance from the between the two bottom C impellers /C, mm mm 50 100 100 100 150 225
200 100 150 200 150 112.5
Overall power number Np
7.77 7.77 7.77 7.77 9.95 9.95
Upper impeller
0.61 0.60
1Flow number
Pump-
Lower impeUer
ing
0.60 0.65
Hydraulic efficiency
Total
effectiveness
Mean
Turb ulent
Total
0.92 0.55 0.84 0.78 1.21 1.25
11.9 7.0 10.9 10.1 12.2 12.6
19.4 10.7 19.1 19.9 27.0 33.5
17.8 14.3 17.2 13.4 15.6 19.4
37.3 25.1 36.3 33.4 42.6 52.9
Chapter 1. Flow patterns
42
Power number, flow number, hydraulic efficienqr of multiple (disc turbine-pitched blade turbine) impellers. Clearance between the two impellers /C, mm
Clearance from the bottom C mm
power number Np
Upper impeller
Lower impeller
Total
ing effectiveness
Mean
Turb ulent
Total
50 100 100 100 150 225
200 100 150 200 150 112
6.53 6.76 6.75 6.98 7.23 7.21
0.83 0.86 0.87 0.86 0.82 0.78
0.96 0.76 0.79 0.73 0.74 0.70
1.79 1.62 1.66 1.59 1.56 1.48
27.43 23.89 24.58 22.73 21.65 20.53
35.1 40.7 33.9 34.2 30.5 24.6
16.9 23.6 19.9 18.1 17.06 17.8
52.0 64.3 53.8 52.3 47.5 42.4
]^low number
Overall
Hydraulic efficiency
Pump-
Results
H§iulr 1 it 11 mi 1
\\\
. . . . ; • ^Z-^"-^* . l^C^r*
lf\\ 111 \\\\ !T \ /ifttt11 *1 111 itji i \ \ •/ll n 111 M f
\ •M
I.Xt<»A\t,
11111
f 1 1 INNVW
•M
..J
rut i
M r I VI M »
iv^ •"• r n r n . r,,..
1
\llif/ > u i
^
./I
1111/11*" ..l\l^>--
'/ I I / j i i « / »
.rl
Ui i J i//''
n !i j i M t i I [1 i—i-iMlLi '*— m i M 11\>»
yi 11 I T ( I / 1 / ^ 1/I Ifj/Mlr.
<• •
'// (b)
10
W>
W
(I)
Flow pattern (vector plots) generated by disc turbine-disc turbine (DT-DT) combination.
No. A B C D E F
C,m 0.2 0.1 0.15 0.2 0.15 0.112
IC,m 0.05 0.1 0.1 0.1 0.15 0.225
Nomenclature DDl DD2 DD3 DD4 DD5 DD6
1.1 Single phase
43
, ^ . . N \ \ \
\lt il 1
H "
fTT/TliiiJ //Ut MM I
lY|U''"
v\\
•;,
•lli ^//i
Iff/j////,. M
1
||l\lliw •'
1 Ml 111 /111 m .
nii/j///i..j
l/lli//// nwwvv
I Ml///""
l-'-^
rrrAi) if,.,'l\ innnii 1 Mj \ / u n M M.
% //
Flow pattern (vector plots) generated by disc turbine-pitched blade downflow turbine (DT-PTD) combination. No. 1 2 3 4 5 6
C,m 0.2 0.1 0.15 0.2 0.15 0.112
/Cm 0.05 0.1 0.1 0.1 0.15 0.225
Nomenclature DPI DP2 DP3 DP4 DP5 DP6
Notation C D H IC N Np P T w p
clearance of the bottom impeller, m or mm impeller diameter, m height of liquid from bottom, m or mm clearance between the centers of the two impellers, m or mm impeller speed, 1/sec power number, P/N^D^ impeller power consumption, W vessel diameter, m blade width of PTD, m liquid density, kg/m^
Chapter 1. Flow patterns
44
Moore, L. R T, Cossor, G. and Baker, M. R., Chem. Eng. Sa., 50,2467 (1995) Velocity Distributions in a Stirred Tank Containing a Yield Stress Fluid Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.147 m Baffle Number: 4 Width: 0.0147 m Impeller Type: (1) 45° pitched blade with six-blades (2) a six-bladed standard Rushton disc turbme Diameter: (1)49 mm (2) 50 mm Number of impellers: (1) 1 (2) 1 Number of blades on impeller: (1) 6 (2) 6 Length of impeller blade (perpendicular to shaft): (1) - (2) 12.5 nmi Width of impeller blade (parallel to shaft): (1) 6.8 nun (2) 10.0 mm Thickness of impeller blade: (1) 1.5 mm (2) 1.5 mm
Working fluid and its physical properties an aquenous solution of 0.17 wt% of a carboxy-vinyl polymer Model
Yield stress Ty
Herschel-Bulkley Power law
18.9 Pas
4.6 12.1
0.46 0.29
Flow measurement technique Laser-Doppler velocimetry
Results
Radial distribution of radial velocity for the pitched-blade turbine: (D)z*=0.41; (O)z*=0.24; (+)2:*=0.0; (•)z*=-0.24; (•)z*=-0.41.
1.1 Single phase
Radial distribution of axial velocity for the pitched-blade turbine: (n)z*=0.41; (O)2:*=0.24; (+)z*=0.0; (•)z*=-0.24; (•)z*=-0.41.
Radial distribution of tangential velocity for the pitched-blade turbine: (n)z*=0.41; (O)z*=0.24; (+)z*=0.0; (•)z*=-0.24; (•)z*=-0.41.
Notation D impeller diameter, m r radial coordinate r* dimension less radial coordinate, r/ru dimensionless r\ impeller tip radius, m T tank diameter, m z* dimensionless axial coordinate
45
46
Chapter 1. Flow patt«ms
Mavros, P. Xuereb, C. and Bertrand, J., Trans. Instn. Chem. Erie's., 74, Part A, 658 (1996) Determination of 3-D Flow Fields in Agitated Vessels by Laser-Doppler Velocimetry: Effect of Impeller TVpe and Liquid Viscosity on Liquid Flow Patterns Experimental apparatus Vessel Type: dish-bottomed Diameter: T Height HiH^T Baffle Number: 4 Width: T/IO Impeller Type: (1) a standard Rushton turbine (RU) (2) a three-blade Lightnin A310 (3) a MixelTT agitator
c (a)
^
^ ^
5
(b)
The Mixel TT agitator; (a) plane view; (b) front view. D=95 mm; blade height 24 mm Diameter, D: (1), (2), (3)Z)/r=0.5 Off-bottom clearance: T/3 Working fluid and its physical properties 1% (w/w) of carboxymethyl cellulose (CMC) T [mPa]=41.2 f'^'^ Flow measurement technique Laser-Doppler velocimetry
1.1 Single phase
47
Results
v/v;^^=o.4o I/ / '
' * \
\\»
II 11 • • I » • '
U I I M I ''^
\\ i * I '
•7TTH4T^ • / / / / / / ,. .//Ml I -
;;iiiiu (b)
(a)
**
I
•
t
V
•
.\N>^s;^
\\\
*^* \ \ \ \
^^=f
il
A\ ^
^/ // M / .;
(d)
(c)
(e)
(t)
Pseudo-2D maps of composite axial andradialvelocities, (a-^c) plain waterflowpatterns; (d~f) flow patterns in 1% CMC solution, (a, d) Rushton turbine; (b, e) Mbcel TT; (c, f) Lightnin A310
Chapter 1 . Flow patterns
48
0.20
•
'
'
1
— • — h • Ofh^+S
RU
—O-h-C-S
0.15 0.10
\
f S.
(•) "
0.05 fldgeof impalle r
0.00 •0.05 .n in 0.20
I
1
I
I
1
!
1 1. . 1 L,
'
I
'
•
'
1
i
'
'
1
1
1
•
1
•
> •
1
'
'
'
1
'
'
•
1
'
'
NRU --0—h.C-5
0.15
I
0.10 0.05
1 '
'
• i
' • ' 1
F
—O—NLA.h-C-5p
y » ^
0.40
1.
0.00
0.20 0.00
•dgeof impalier
>0.05 .n in
0.60
(b) i
'
—•—LA.h-C-5 W
-0.20
} ,
1
20
.
.
.
.
.
40
.
.
-0.40
I «
80
60 r(nim]
100
Axial velocity measurements for the Rushton turbine 5 mm above and beneath the agitator blades, (a) water; (b) 1% CMC solution 95 90 85
' I ' ' • 1 •••
1 •
- I
U
1 •t
1 1
i
20
III
1 • *
1
40
1
1
.
1
60 r|mmj
1
I
1
1
80
•
1
•
1
100
Axial velocity profiles 5 mm below the agitators; (a) Mixel TT; (b) Lightnin A310. TT, LA: water; NTT, NLA: 1% CMC solution
•'"T^
-NLA -NTT
80 75 70 65 60 55 100
(a) Radial velocity profiles off the edge (Ar=9.5 nun) of the impellers; (b) axial velocity profiles 5 mm above the agitator blades
Notation C impeller off-bottom clearance, m D impeller diameter, m hb agitator blade height, m T tank diameter, m V fluid velocity, m/sec Y shear rate, Hz Subscripts r radial tip tip
1.1 Single phase
49
Rutherford, K., Lee, K. C, Mahmoudi, S. M. S. and Yianneskis. M.^AIChE Journal, 42,332 (1996) Hydrodynamic Characteristics of Dual Rushton Impeller Stirred Vessels Experimental apparatus Vessel Type: flat-bottomed Diameter: (1) 294 mm (2) 100 mm Liquid contained Height: (1)294 mm (2) 100 mm Baffle Number: 4 Width: 0.1 T Impeller Type: Rushton impeller Diameter: T/3 Number of impellers: 2 Number of blades on impeller: 6 Impeller clearance and separation: 01=0.257 and C2=0.50T; 01=0.337 and €2=0.337; 01=0.157 and C2=0.50r Working fluid Distilled water Flow measurement technique Flow visualization and Laser-Doppler anemometry Experimental conditions Impeller rotational speed: 250 rpm (Vi^^=1.28 m/sec) in vessel (1) 2,165 rpm (Vi,>=3.77 m/sec) in vessel (2) Results VHP
^ .\ , .
• / • I
' *
» V * J
w 111 ' '/ ' '/ "
•^
^ f
S.'<
?ll
Parallel flow 6 =0** r-z plane 360° ensemble-averaged Merging flow 0 =0° r-z plane 360* ensemble-averaged mean velocity vectors: (CI =0.337, C2=0.337). mean velocity vectors: (CI=0.257, C2=0.507).
Chapter 1. Flow patterns
50
VHP
/ * \» ^1
^/
\\ « \ I \
n u! DivergingflowB =0** r-z plane 360** ensemble-ave^^ged mean velocity vectors: (C1=0.15T, 02=0.507).
Notation CI C2 C3 T Yap
off-bottom clearance of the lower impeller separation between the two impellers submergence of the upper impeller below the top of the liquid column height vessel diameter impeller tip speed
1.1 Single phase
51
Jaworski, Z., Nienow, A. W. and Dyster, K. N., Can. /. ofChem. Eng., 74,3 (1996) An LDA Study of the Turbulent Flow Field in a Baffled Vessel Agitated by an Axial, Down-Pumping Hydrofoil Impeller Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.222 m Liquid contained Height: 0.222 m Baffle Number: 4 Width: 0.022 m Impeller Type: (1) Chemineer HE3 impeller (CHE3) (2) Prochem Maxflo T impeller (PMT)
Diameter: (1) 0.102 m Number of impellers: (1) 1 Number of blades on impeller: (1) 3 Off-bottom clearance: (1) 0.056 m Working fluid Distilled water Flow measurement technique Laser-Doppler anemometry Experimental conditions Reynolds number: (1)4.77x10*
(2) 0.078 m (2) 1 (2) 6 (2) 0.100 m
(2)2.44x10*
Chapter 1 . Flow patterns
52
Results
Mean axial velocity profiles for Chemineer HE3 impeller.
Mean axial velocity profiles for Prochem Maxflo T impeller.
R^ Rg R3 R^
Rg Rg
N N
•0.2 0.0 0.2
V
Mean radial velocity profiles for Chemineer HE3 impeller.
-0.2 0.0 0.2
w ^R
Mean radial velocity profiles for Prochem Maxflo T impeller.
1.1 SingI* phase
53
N
•;; ;>C:--'' Vector plot of mean velocity vectors in the R-Z plane for CHE3.
•jMfcJ>Jil»5MML-J
Vector plot of mean velocity vectors in the R-Z plane for PMT.
0.2 r 0.0 ^
^2 y?9W W M . f ? 999
2..
N
>
Fluctuating velocity profiles for CHE3.
Fluctuating velocity profiles for PMT.
54
Chapter 1. Flow patterns
Notation D impeller diameter, m H liquid height in tank, m N impeller rotational speed, 1/sec r radial coordinate, m R dimensionless radial coordinate, r/T, dimensionless T tank diameter, m d mean velocity, m/sec V' rms fluctuating velocity, m/sec V dimensionless mean velocity, v/nDN, dimensionless V dimensionless rmsfluctuatingvelocity, v'/nDN, dimensionless z axial coordinate, m Z dimensionless axial coordinate, z/H Indices R radial component T tangential component Z axial component
1.1 SingI* phase
55
Hockey, R. M. and Nouri, J. M., Chem. Eng. Sd., 51,4405 (1996) Turbulent Flow in a Baffled Vessel Stirred by a 60° Pitched Blade Impeller Experimental apparatus Vessel Type: flat-bottomed Diameter: 294 mm Liquid contained Height: 294 mm Baffle Number: 4 Width: 29.4 mm Impeller Type: 60° pitched blade impeller Diameter: 98 mm Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): 49.0 mm Projected width of impeller blade (parallel to shaft): 18.5 mm Off-bottom clearance: 98 mm Working fluids water and two mixtures of water and maltose syrup Flow measurement technique Laser-Doppler velocimetry Experimental conditions Reynolds number (/?e=Z)^Wv)=48,000 Results
\i i
111111
& ^ ::^.
I 0.0
•
T" 1.0
2.0
3.0
Meanflowvelocities for Reynolds and power numbers of 48,000 and 2.2, respectively, in Q ^O"* plane: (a) axial and radial velocity vector; (b) tangential velocity profiles.
Chapter 1. Flow patterns
56
Notation D H N r R Vt z V
impeller diameter, m liquid height in the tank, m impeller rotational speed, 1/sec radial distance from the center of the tank impeller tip radius, m impeller tip velocity, itND, m/sec axial distancefromthe bottom of the tank fluid kinematic viscosity, mVsec
0.0
1.0
^ r/R
2.0
"1 3.0
Radial and tangential mean velocity vector mr-d plane for Reynolds and power numbers of 48,000 and 2.2, respectively, at different axial positions: (si)z=0,27H: (b)z=0.17^; ic)z=0.068H.
1.1 Singte phase
57
Harvey, A. D., Wood, S. R and Leng, D. E., Chem. Eng. Sci., 52,1479 (1997) Experimental and Computational Study of Multiple Impeller Flows Experimental apparatus Vessel Type: ellipsoidal-bottomed Height: 55.88 cm Baffle Number: 4 Width: 3.157 cm Thickness: 0.635 cm
Impeller
Type: 45° pitched-blade impeller Number of impellers: 4 Number of blades on impeller: 4 liquid level
baffle
4H
'Shaft
a) 2^2=3.58 Impeller 4(14)
b)z/Ra«353 c)z/R,=:2.89
]
d)2/R,»2.55
impeller 3 (IJ e) z/Rj= 2.21 f)2/Rj«1.87 g)z/R2-1.53
2(y h)z/Rj«1.19 Impeller dimensions and positioning for easel T „ _ Blade X-section ^P^"^' axu;)(cm)
1
r/R,
Schematic of multiple impeller configuration
1 2 3 4
0.318x1.75 0.318x4.13 0.238x2.54 0.318x2.54
Diameter (cm)
Height (cm)
9.207 22.860 17.780 12.383
5.73 18.82 30.73 42.48
Chapter 1. Flow patterns
58
Working fluid and its physical properties 85% (vol/vol) com syrup (viscosity = 928 cP; density = 1,000 kg/m^)
Flow measurement technique Laser-Doppler velocimetry
Experimental conditions Impeller rotational speed: 92 rpm
Results experiments
computations CASE1
|a)2/Rag3.58 b)2ma»3.23 C)zm,«2.89
/////"• //////^"
d)2m,«2.5S e)2/R,«2.21
]f)^^-
1.87
g)2ma«1.S3 h)z/Rgs1.19
Comparison of computed (left-handside) and experimental (right-handside) velocityfieldsfor case 1
1.1 Singl* phase
59
Case 1 velocity profiles for axial stations a-h
Notation / w
thickness of blade, cm width of blade, cm
60
Chapter 1. Flow patterns
Tanguy, R A„ Thibault, E, La Fuente, E. B-De., Espinosa-Solares, T. and Tecante, A., Chem. Eng. Sci., 52,1733, (1997) Mixing Performance Induced by Coaxial Flat Blade-Helical Ribbon Impellers Rotating at Different Speeds Experimental apparatus Vessel and impeller geometry
Mixer dimensions
Working fluids and their physical properties Aqueous Solutions of CMC, Gellan, and Xanthan n (shear thinning index) = 0.26 -- 0.64 consistency index = 2.95 — 21.55 Pas" density = 1,020 kg/m^
Circulation in the vicinity of the Rushton turbine
1.1 Singl* phas«
61
Computational Results
(a) Dispersion pattern induced by the dual impeller mixer. (b) Dispersion pattern induced by the helical ribbon only
0.04
?E
0.03 0.02 0.01
1 1 ^
0.00 -0.01 -0.02 -0.03 -0.12
-0.08
•0.04
0.00
0.04
0.08
0.12
0.08
0.12
Position (m)
(a) 0.04
t
0.03 0.02 f 0.01
I
0.00
(9
-0.01
<
-0.02 -0.03 •0.12
lb)
-0.08
-0.04
0.00
0.04
Position (m)
(a) Axial velocity profiles at «=1. (b) Axial velocity profiles at w=0.33. (black symbols = dual impeller- white symbols = helical ribbon only).
62
Chapter 1. Flow patterns
Mavros, P., Naude, L, Xuereb, C. and Bertrand. J., Trans. Instn. Chem. Engrs., 75, P ^ A, 763 (1997) Laser Doppler Velocimetry in Agitated Vessels: Effect of Continuous Liquid Stream on Flow Patterns Experimental apparatus Vessel Type: dish-bottomed vessel with a radius of curvature of 190 nun Diameter: 190 mm Liquid contained Height: 190 mm Baffle Number: 4 Width: 19 mm Impeller Type: (1) a standard Rushton turbine (2) a Mixel TT
Picture of the Mixel TT agitator Diameter: 95 nwn Number of impeUers: 1 (2) 3 Number of blades on impeller: (1) 6 Off-bottom clearance: (1) 63 mm (2) 63 nun Working fluid Tap water Inflow and out flow of water Waterflowrate: 6.41 i/min Location of inflow: in the mid-plane between two adjacent balQes, 43 mm away from the agitator shaft and with its tip 153 nun from the vessel bottom Location of outflow: bottom of the vessel Flow measurement technique Laser-Doppler velocimetry Experimental conditions Impeller rotational speed: 3 Hz
1.1 Single phas«
63
Results 95 -RU -RUCCE") -RU(-CD-)
85
E
80
N
75
I 0
0.2 0.4 0.6 Radial velocity U/U^ [-]
' I ' ' ' ' I ' ' • • I ' ' ' ' I
90
70
55 -0.2
0.8
Rushton turbine
-RU -RUrCE") -RUrCO")
-0.05
-r
0
1"
0.5
I. I 1.S
'
'
'
1
'
•
'
F i V ^ positive ra
MixeITT
1
•
\
•
0
' -T—1—1-
0.05
"
1
1—r - T - i
2 « 92 mm H
/
m7////Aiim!i^/A. .
2 0.3
-0.1
Radial velocity U^/UH [.
2 « 87 mm H
-0.15
—o—TT |j —*—TTrCE-)B —•~7TrCD")R .1
1. .
. 1
L • J
MIxeITT
Rushton turbine -RU -RUfCE-) -RU("CD-)
0.2 0.1 0 -0.1 -0.2 -0.3 20
40 60 Vessel radius [mm]
Rushton turbine
20
40 60 Vessel radius [mm]
Mixcl TT
Effect of incoming liquid stream on dimensionless mean radial and axial velocities around the impellers.
Chapter 1 . Flow patterns
64
95
•-f . 1 - t 1 f , . r-| f t-T r-f-^- * T . , «-i T x - j - r - r - .
90 t — 0 ~ RU f C n —A—RU 85 L*~-.Sv^^^ n ^^^tR:*-~.^_ ^^••>^J^^~--—-_ 80 n0 ^^*>^^ •——^ 75 70
n kl W H W
^^"-'^^ nD T 1 J_ JS . ^ , .^"^""^^ ^—"•^^
M n H
n 65 HK1 0 60
'. 1,^ , ^^^-^ • X / -.-# - ^
^D-*"^^ ^^-^^'^ .^^^\^ A-'D^
J
Ta
H J d 3 1 H -1
1
3 A
1
55 0.1
0.2
0.3
0.4
0.5
0.6
180
150
120
90
60
30
Tangential flow angle 6 ("]
Tangential velocity V A^ [-] 95
I • I I I I I I • I I I I I f 11
9 0 1 1 —Q—rr 90 8 5 pJ 1 —A—TTrCE")j 85
-rrccE-)
80 1 E 80 E, 75
-s I
.700 65 60 I . . . . I . . ^ 1 . I • • . . 1 I . . • . . I . . . « . I . . . • .T
55 0.02
0.04
0.06
Tangential velocity V / V
0.08
0.1
180
150
120
90
60
Tangential flow angle 8 [*]
[-]
Mixel TT
Rushton turbine
Effect of incoming liquid stream on the tangentialflowaround the impellers. WK,>=0.40 I/ / ' * " \
w*
\I I I ' ^ \
r""
il n * » I * U II " i
^'^W
,t
s^ ^yL>
..nil ^ ^ . / / M l 1 ..)
Feedingtube plane
90°-rotalcd plane
Batch (no flow)
Composite U„flowpattern; Rushton turbine, N=3 Hz, QL=6.41 min
30
1.1 Single phase
65
V/VHP=-OAO
Feedingtube plane
90°-n)tated plane
Batch (no flow)
Composite U„flowpattern; Mixel TT agitator, N=3 Hz, QL=SAI min *.
Notation N impeller rotational speed, Hz QL waterflowrate, ^/min U instantaneous velocity value, m/sec n mean velocity value, m/sec Vtip impeller tip speed, m/sec Indices r radial 2 axial q tangential
Chapter 1. Flow patterns
66
Schafer, M., Yianneskis, M., Wachter, R and Durst, F.,AIChE Journal, 44, 1233 (1998) Trailing Vortices around a 45° Pitched-Blade Impeller Experimental apparatus Vessel Type: flat-bottomed Diameter: 152 mm
Liquid contained Height: 152 mm Baffle Number: 4 Width: 15.2 mm Impeller Type: 45° pitched-blade impeller Diameter: 50 mm Number of impellers: 1 Number of blades on impeller: 4 Projected width of impeller blade: 10 mm Off-bottom clearance: 50 mm Working fluid and its physical properties Silicone oil (density = 1,039 kg/m^; dynamic viscosity = 0.0159 Pasec) Flow measurement technique Laser-Doppler anemometry Experimental conditions Impeller speed: 2,672 rev/min Results
Angle-resolved mean velocity vectors in the vicinity of the impeller blade in seven ^ planes: (a) 0=0^; (b) 0=2''; (c) 0=8«; (d) 0=30^
1.1 SingI* phase
67
0.5 v^
0.26 0.20
0.00
td)
Angle-resolved mean velocity vectors near the blade in four planes inclined at 45** to the horizontal plane. Each of these planes intersects the followmg ^ plane at midblade: (a) 0=80'* (-lO**); (b) 0=0**; (c) 0=4*»; and (d) 0=15^
Chapter 1 . Flow p a t t « m s
68
0.4
3.00-n
,
If
z/T
2.50 J
r/T
0.3 H
2.O0J I.50J
0.2 Jpeno^^oo^^oo^^^o^^^^^^^^ 0.1 H
i.ooJ
ii
0.50 J
^ ^ ^ ^ ^ t ' M i l l i-rn
0
20
40
1 60
1 80
Blade angle [°] (a)
r 100
120
0 00-i 0
50
100
J 15
Blade angle [°] (b)
(a) Variation of the nonnalized coordinates rIT, z/T of the vortex axis with blade angle 0; (b) variation of the vortex radius nonnalized with distance from the blade along the vortex axis {r*/d') with blade angle 0; (c) isosurface of vorticity at the edge of the trailing vortex behind an impeller blade.
Notation d' distance from the blade along the vortex axis, m D impeller diameter, m N impeller rotational speed, 1/min r radial coordinate: distance from the axis of the vessel, m r* trailing vortex radius, m T vessel diameter, m VHP impeller tip speed, nND/60, m / s e c z axial coordinate, m 0 the blade; 0 = 0 ° is the vertical plane through the middle of the leading blade
69
1.2 Multi phase 1.2.1 Solid-liquid systems Gosman, A. D., Lekakou, C, Politis, S., Issa, R. I. and Looney, M. K.,AIChE Journal, 38,1946 (1992) Multidimensional Modeling of Turbulent IWo-phase Flows in Stirred Vessels Experimental apparatus Vessel T)rpe: flat-bottomed Diameter: 0.294 m Liquid contained Height: 0.294 m Baffle Width: 0.0294 m Impeller Type: disc turbine Diameter: 0.098 m Number of impellers: 1 Off-bottom clearance: 0.098 m Working fluid, solid and its physical properties Fluid: water Solid: glass particles; density = 2,950 kg/cm^; mean diameter = 232.5 pm Computational conditions Impeller speed: 300 rpm Solid concentration: 0.02% Results
• * • • • • • •
I I '
'
•:•
i i i i i i i t « \ \ \ \ \ i t
« I
f I
I
I
I
I I I t t t \ \ t I
I I I
I t I
i
I M ' ' I * « t I I I I I I I 1111 n u M i 1/ / ' '•• ^ » M I I I I 11 M n 11 I I 11
I//'
M t l I I I M M t 11 I I i i I
1/ / ' . ' : • ' M I I I I I M I I I I I I M I I / I •:• ' I / I I I 1'i' / / / / I
\ \ -i' / / / / / ( \ \ ^t- ^ / / / I
i I t I n u l l I I 11 I M 1 M I 1 I I I II I 1 n i I I I 1 I II
\1'^-^-+ l^--
iaaa,j
/ '^^^\\ \ \ \ \\
' ' •*M \ \ \ \ W I \ *:• • M I I I 1 1 WW l \ \ - i - ' / / / / / I MIWI \ \ \ -;- - X / / / / / / M I I I \ \ \ N ^ | - . ^ ^ x / / / / / / / n 11II I I I \\\-^-J
^^y^^^y
% \ >.^-;,,
• • - ^ ^ ^ ^ ^ ^ > » • • • • / / / f t /
///
/ f/ ;/ I M M I
Velocity vectors @ 6=0°; scale: -* =0.82 m/s.
II
Chapter 1. Flow p«tt«ms
70
Velocity vectors @ jc=0.908ft scale: -> =0.15 m/s.
Velocity vectors @ x=Q.3H; scale: -> =0.63 m/s.
Notation /f Height of mixing vessel
1.2 Multiphase
71
Computational results 0.2S' Cro-
O O
ats-
0.10o 0.0S-
>^
O
_-.a
0.00-
.0.2
0.0
0.2
0.4
0.0
0.0
1.0
Mean velocity comparisons: (a) above the impeller @ Jf=0.1203 m (axial); (b) below the impeller @ jc=0.0757 m (axial); (c) impeller stream @/?=0.0515m (radial). o Nouri (1992). -o- predicted solid phase, — predicted liquid phase.
rms velocity comparisons: (a) above the impeller @ x=0.1203 m (axial); (b) below the impeller @ jc=0.0757 m (axial); (c) impeller stream @/?=0.0515m (radial). o Nouri (1992). -a- predicted solid phase, — predicted liquid phase.
Nouri, J. M. and Whitelaw, J. H., Int. J. MuUiphaseflow, 18,21 (1992).
72
Chapter 1. Flow pattoms
Pettersson, M. and Rasmuson, A. C.,AIChE Journal, 44,513 (1998) Hydrodynamics of Suspensions Agitated by Pitched-Blade Turbine Experimental apparatus Vessel Type: flat-bottomed Diameter: 210 mm Height: 210 mm Liquid contained Volume of liquid in vessel: 7 i Baffle Number: 4 Width: 22 mm Clearance of bafflefromwall: 7 nmi Clearance of bafflefrombottom: 8 mm Impeller Type: 45° pitched four-bladed turbine (downwards pumping) Diameter: 82 nun Number of mipellers: 1 Number of blades on impeller: 4 Length of impeller blade (perpendicular to shaft): 33 mm Projected height of impeller blade: 12 mm Off-bottom clearance: 70 mm Working fluid, solids and their physical properties Liquid: deionized water Solid: (1) seed particles: spherical metallic coated glass particles (density = 2.6 g/cm^; number mean size = 4 ^m) (2) process particles: glass beads (density = 2.42 g/cm^; mean size = 321 ± 9.6 ^m) Flow measurement technique Three-dimensional phase-Doppler anemometry Experimental conditions Impeller speed: 450,525, and 600 rpm Seed particles: 0.10 g; process particles: 0.06% by volume Results
Normalized 3-Dfluidmean velocity, N = 450 rpm.
1.2 Multiphase
73
80 100 0 (mm]
r 20 40 60 80 ndUl distance (mm]
100
Normalized rmsfluctuatingvelocities at A = - 1 0 mm. N = 450 rpm.
Normalized turbulent kinetic energy. N = 450 rpm.
3-D intensity of turbulence, N = 450 rpm.
Chapter 1. Flow patterns
74
-o-1^-A•«-
h=-30 mm h=-10mm| hslOrom h=30 mm
0.00H 0
40 80 radial distance [mmj
40 80 radial distance [mm]
radial distance [mm]
radial distance (mm] ^ 0.08 " i 0.06^ §
0.04 0.02
i" 0.00 J -fci^i 0
40 80 radial distance [mm]
Normalized Reynolds stresses. N = 450 rpm; ^ = 85°,
Notation Di
N Q
Tu U'i
u U'i'U'j
impeller diameter, m impeller speed, 1/sec turbulent kinetic enei:gy, mVsec^ 3-D intensity of turbulence, % normalizedfluctuatingvelocity, m/sec 3-D mean velocity, m/sec Reynolds stress, mVsec^ tangential component
»Hi-
-r 0 40 80 radial distance [mm]
1.2 MuKiphas«
75
1.2.2 Gas-liquid systems Ogawa, K., Yoshikawa, S. and Shiode, H., Kagaku Kougaku Ronbunshu, 18, 495 (1992) Flow Characteristics of Discharge Flow Region in a Stirred Vessel with Aeration Experimental apparatus Vessel Type: flat-bottomed Diameter: 312 mm Liquid contained Height: 312 mm Baffle Number: 4 Width: 31 mm Impeller Type: sixflat-bladeturbine Diameter: 104 mm Number of impellers: 1 Number of blades on impeller: 6 Length of impeller blade (perpendicular to shaft): 26 mm Width of impeller blade (parallel to shaft): 20.8 mm Off-bottom clearance: 104 mm
Sparger Location: directly below the impeller Direction offlow:downwards
58 mm from vessel bottom
Working fluids and their physical properties Liquid: Kinematic viscosity (mVs) ion-exchanged water 1.03 x 10"^ 40 wt% glycerol aqueous solution 4.30 x 10~^ 60 wt% glycerol aqueous solution 4.30 x 10~® 0.5 wt% polyacrylamide aqueous solution (pseudoplastic viscosity = 0.132 Ns7m^; integer M = 0.647) Gas: air Flow measurement technique Electrode reaction velocimetry Experimental conditions Liquid
NiX/s)
0(^/min)
Test liquid
4
7 14 14 14
water, 40%G., 60%G., PAA water, 40%G., 60%G., PAA water, 40%G.,60%G., PAA water, 40%G., 60%G., PAA
5 6
Chapter 1. Flow patterns
76
Results
PA A no aeration
aeration
N=As-\0=lAI/min .,,
Contour line map of velocity for PPA aq.
r/D, l-l
0 0.5 r/0. l-l Velocity distribution for water
1.2 MultiphM*
77
^
Z1.2 o"
U
Oll/mtn)
1.^
Nn/&)
4
5
wQler
•
0
6 o
"T] l
o
h
Nl.O
0^
0.5 r/D, (-1
1.0
Relationship between axial position and radial position at where velocity takes maximum value for water Notation Di impeller diameter, m N impeller rotational speed, 1/sec Q airflowrate, i/min r radial position, m u velocity, m/sec Ut tip velocity of impeller, m / s e c Z axial position
Chapter 1. Plow patt«ms
78
Gosman, A. D., Lekakou, C, Politis. S., Issa, R. I. and Looney, M. K.,AIChE Journal, 38,1946 (1992) Multidimensional Modeling of Turbulent TWo-phase Flows in Stirred Vessels Experimental apparatus Vessel Type: flat-bottomed Diameter: 1.83 m Liquid contained Height: 1.67 m Baffle Width: 0.18 m Impeller Type: disc turbine Diameter: 0.915 m Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: 0.41 m Sparger Air was injected from a 2.5 cm disc located on the vessel axis, 0.2 m from the base. Working fluids Liquid: water Gas: air Computational conditions Impeller speed: 70 rpm Air rate: 1,102 ^/min wall
Radial profiles of axial velocity at different axial stations @ ^=17.5**.
1.2 Multiphase
79
Gas phase profiles @ ^=15**; (a) jc=1.52 m; (b) Jif=1.04 m. D Revill and Irvine (1987), — predictions.
Gas phase profiles @ ^=15°; (c)ji:=0.41m;(d)x=0.12m. • Revill and Irvine (1987), — predictions.
Revill, B. K. and Irvine, K., ICI pec, private communication.(1987).
Notation X, r, 6 qrlindrical coordinate
Chapter 1. Flow patterns
80
Manikowski, M., Bodemeier, S., Liibbert, A., Bujalski, W. and Nienow, A. W, Can. J. ofChem. Eng., 72,769 (1994) Measurement of Gas and Liquid Flows in Stirred Tank Reactors with Multiple Agitators Experimental apparatus Vessel Type: flat-bottomed Diameter: 440 mm Height: S r Volume: 200 £ Number: 4 Width: 44 mm Clearance of bafQe from wall: 4.4 mm Impeller Type: (1) Rushton turbine (2) Rushton turbine (3) Lightnin A-315 impeller Diameter: (1) T/3 (2) 0.45 T (3) 0.43 r Impeller setup: three Rushton turbines turbine (1) x 3 two Lightnin impellers and one Rushton turbine impeller (3) x 2 + turbine (2) x 1 Location of impellers: |_
7S2
.
p.' i
1
r
[i
P
D
r' 1
1 i Vl52j r 1
D
.'•'l
4
»
«o
1 r^
D J
,
v^~
1012 1320
1 m
Schematic view of the stirred tank, dimensions in mm. On the left hand side of the impeller shaft, the gas sampling probe for gas transit tune measurements is shown. It can be moved parallel to the shaft On the right hand side, the arm is shown on which the probes of the ultrasound measuring device are mounted. The arm by which the probes can be swept between the reactor wall and the shaft isfixedto a steel tube attached to one of the bafQes, as shown on the right hand side of the figure. Sparger design Sparger position: fixed to the reactor bottom Holes: holes are arranged on a circle of 120 mm diameter
1.2 MuttiphaM
81
Working fluids and their physical properties Liquid: aqueous solutions of CMC Rheological properties of CMC solutions Concentration (% w/v) 0.8 1.2
K (Pas") 0.086 0.12
0.83 0.82
Gas: air Bubble velocity distribution measurement Ultrasound Doppler technique Experimental conditions Aeration rate: 4.0 mVhr (0.33 wm) Results 5 rev/s 6.7 rev/s
«J
8.3 rev/s
Rj
v\\\\\\\J
A 8J
8j
8j
iiwuV:' K\\\\\\\
\\\\\\\\
\\\\\\}
SJ
^J \\\\\\\\>^
^ i f
«J
RJ
KWWwi
\\\\\\\M
v[cm/sj
,.//
100
200
0
100
200
—r 200
Radius [mm] The patterns of the axial-radial components of the mean bubble velocities at 8.3,6.7, and 5 rev/s in a 0.2 % w/v CMC solution aerated at 4.0 mVh. Notation K consistency index, Pa(sec)'' n Flow behaviour index, dimensionless T tank diameter, m V mean bubble velocity, m/s y shear rate, 1/sec r shear stress. Pa
32
Chapter 1.
Plowpattams
Morud, K. E. and Hjertager, B. H., Chem. Eng. Scu, 51,233 (1996) LDA Measurements and CFD Modelling of Gas-Liquid Flow in a Stirred Vessel Experimental apparatus Vessel Type: dish-bottomed Diameter: 0.222 m Liquid contained Height: 0.222 m Volume of hquid in vessel: 7.5 i Baffle Number: 4 Width: O.ID Clearance of baffle from wall: 0.05Z) Impeller Type: six-bladed Rushton turbine Diameter: D/3 Number of impellers: 1 Number of blades on impeller: 6 Diameter of impeller disc: 0.243Z) Length of impeller blade (perpendicular to shaft): 0.09Z) Width of impeller blade (paraDel to shaft): 0.09Z) Off-bottom clearance: 0.47Z) Sparger Height: 0.108Z) Diameter: 0.108Z) Location: below the center hne of the impeller shaft Distance between the top of the sparger and the bottom of the vessel: D/5
Working fluids Fluid: distilled water containing 4 g NaCl/^ Gas: air
Flow measurement technique Laser-Doppler anemometry
Experimental conditions Impeller rotational speed (ppm): 360,400,540 and 720 Gas flow rate (WM): 0.09,0.49,0.75,1 and 1.33
1.2 Multiphase
83
Results
-I—•—I—'—r 0.2 0.4 0.6
0.0
0.8
1.0
(a)
Measuredradialgas velocity at the impeller height for different gas flow rates (a) Q=0.09 wm, (b) ©=0.49 wm. (c) Q=1.00 wm, (d) Q=1.33 wm.
g.e-
h«0.47 D 1.00 W M —4—720 RPM -e-540RPM — « ^ 400 RPM - B - 3 6 0 RPM
0.4-
2
0.2- ...
r,r'"
L-t-''-'-.
D
r:,-^
y^.-...'
0.0-
': :• 0 .0
,
'.-i'l-' '
1 02
•
1 0.4
'
1 0.6
'
1 0.6
• 1 .0
(c)
Measured axial gas velocity at the impeller height for different gas flow rates (a) Q=0.49 wm, (b) Q=0.75 wm, (c) ©=1.00 wm, (d) ©=1.33 wm.
84
h=0.72D 1.00 W M
-540RPM - 360 RPM
-L- 0.2 H
0.0
(a)
r'H
-I 0.2
(b)
'
1 0.4
'
1 ' '' I 0.6 O.B
1.0
rM-1
Measured tangential gas velocity at 1 wm (a) at the impeller level {h=0A7D), (b) above the impeller (h=0.72D).
1
Uog
T7
-Q H
(a)
Ho
t
Gas
(b)
(c)
GasflowrateQ=1.0 wm, (a) Vessel configuration, (b) Predicted gas pattern, (c) predicted gasfractioncontours.
Notation D h Ho 0 r R U V W Wiip U*
vessel diameter, m distance from vessel bottom, m initial liquid level, m gas flow rate, W M radial coordinate, m vessel radius axial velocity, m/sec radial velocity, m/sec tangential velocity, m/sec impeller tip velocity, m/sec U/WHP; F * = V/Wtip; W*= W/W^p;
r*=r/R
85
Chapter 2.
Mixing time
2.1 Single piiase Peters, D. C. and Smith, J. M., Can. J. ofChem. Eng., 47,268 (1969) Mixing in Anchor Agitated Vessels Experimental apparatus Vessel Type: flat-bottomed Diameter: 6,9 and 12 in Impeller Type: anchor Number of impeller: 1 Width of impeller blade: 1 in and 1.5 in Working fluid Polyacryl amide solution Measurement technique Use of iodine-thiosulfate reaction Results I2S CLEARANCE 2S'CLEARANCE so'CLEARANCE
40
40
fO
too
SPEED IN REVS/MIN. -
Mixing times for iodine-thiosulphate reaction (clearing). 1 % poly (acrylamide), 12-in. tank, 1-in. wide blade. *the blade-to-wall clearance.
Chapter 2. Mixing time
86
Carreau, P. J., Patterson, I. and Yap, C. Y., Can.]. ofChem. Eng., 54,135 (1976) Mixing of ^^scoelastic Fluids with Helical-Ribbon Agitators I — Mixing Time and Flow Patterns Experimental apparatus Vessel Type: (1) (2) flat-bottomed Diameter: (1) 6 (2) 10 in Height:(l)6 (2) 10 in Impeller Impeller
d (in.)
I II III IV V VI VII
5V8 5V8 5V8 4V8 5V8 8% 8%
h (in.)
ds (in.)
b (in.)
5%
V4 V4 V4 V4 V4
V,6 V,6 V,6 7,6 Vl6 V,6
5 3/8
5V8 5% 5V8 9V32 9V32
% %
—
Nt
D/d
l/d
w/d
p/d
2 2 2 2 1 2 2
1.11 1.11 1.11 1.37 1.11 1.11 1.11
4.48 3.00 4.12 4.00 4.39 4.44 4.69
0.0970 0.0970 0.195 0.121 0.0970 0.0990 0.0724
0.719 1.048 0.707 0.848 0.695 0.690 0.710
N.B. The blade of the impeller VII is made of circular tubing, all the others are made of flat ribbon. d - diameter of impeller h — height of impeller d, = diameter of shaft b = blade thickness Nh = number of blade D — inside tank diameter / = overall length of blade u) - blade width p = pitch .ds
2.1 Single phase
87
Working fluids and their physical properties Glycerol, 2% aqueous solution of sodium carboxyl methyl cellulose (CMC), and 1% aqueous solution of polyarylamide (Dow Chemical Separan AP-30) Properties of fluids Fluid
p, g/cm^ r]o, poises 9o, g/cm S R tu sec. A, sec*
Glycerol
2% CMC
1% Separan
1.25 5.68 — — — —
1.0 100.0 106.0 0.243 0.702 1.26 1.06
1.0 9.0 xlO^ 9.88x10^ 0.392 0.796 299.0 428.0
NOTES 1) 2) 3) 4)
M data taken at 25X. - 2 5 is the slope of log rj vs. log y at large / . (2-2/?) is the slope of log - (TU -T22) vs. log y at large y. Parameters rj*,, Oo* and ti were obtained by curvefittingthe rheological data to the model. 5) The values of A (elastic time constant) were estimated firom: ,.(Zi2a)-l] (Zi2a)a. = 2'"
Here a is a parameter associated with the behaviour of the dynamic viscosity and taken to be equal to 1/(1-25): X is the elastic characteristic time (largest "relaxation time") and Z ( ) is the Riemann zeta function.
Measurement technique Decoloration method: use of the reaction between iodine and thiosulfate in the presence of a starch solution. Results
• Q
^ • •
0
0
4X10
Impeller 1 11 III IV V VI
vu
Influence of impeller geometry on mixing time.
Chapter 2. Mixing tini*
88
3X10
N, RPM
Influence offluidproperties on mixing time.
Notation tm
r -(T11-T22)
p
mixing time, see effective rate of deformation, 1/sec zero shear viscosity, poise primary normal stress difference, dynes/cm^ density, g/cm^
2.1 Singl« phase
89
Brennan, D. J. and Lehrer, I. H., lyans. Instn., Chem. Engrs., 54,139, (1976) Impeller Mixing in Vessels Experimental Studies on the Influence of Some Parameters and Formulation of a General Mixing Time Equation Experimental apparatus Vessel Type Diameter (mm) Height (straight section of cylindrical vessel) (mm) Height (dish-section) (mm) Operating capacity (m^) BafQe width (nrni) Coil diameter (mm) b: bafQed, fb: flat-bottomed, he: with helical coil
b-fb 420 610
b-db 420 495
u-db-hc 420 505
u-db-cp 420 505
— 58.2x10-3 39 —
102 58.2x10-3 39 —
102 58.2x10-3 — 280
102 58.2x10-3 — —
u: unbaffled dp: dish-bottomed cp: with cylindrical probe
Impeller Type Diameter (nun) Number of impellers Number of blades d/D w/d
flat blade disk turbine flat blade turbme 63.5,76.0,100.0 and 102.0 land 2 land 2 6 6 0.15,0.18 and 0.24 0.125 and 0.20
Working fluids and their physical properties Newtonianfluidsof low viscosity
Measurement technique
Decoloration of methyl red indicator with neutralization of NaOH with HCl Experimental conditions and results Baffled vessels (1) Variable, impeller speed: 72
90
Chapter 2. Mixing tim«
Mixing time was reduced by approximately 30% when using dual impellers instead of a single impeller. The position of the additional impeller had negligible effect on G, The investigation was limited to the dish-bottomed vessel Unbaffled vessel (1) Variable, impeller speed: 157 Nmh 0 increased with further increase of TV^ (2) Variable. impeUer position: 0.24 < h/D < 0.66 rf/Z)=0.24; u;/rf=0.125;^/Z)=l.ll With iV at a single speed
d/D=024;H/D=l.ll For all TV values investigated, the reduction of 6 achieved by the wider blade over that by the narrower blade was small. (4) Presence of internal fittings The effects of either a single probe or a heUcal coil as internals in the unbaffled vessel were to retard vortex formation and improve mixing.
Notation d D Fr g h
impeller diameter vessel internal diameter Froude number, N Hig acceleration due to gravity vertical clearance between base of vessel at vessel axis and lower horizontal face of impeller blade H height of liquid surface above vessel base at vessel axis (liquid at rest) N impeller rotational speed Nfrit critical impeller speed in unbaffled vessel at which air entrainment commences Re impeller Reynolds number, Nd ^p/fi w impeller blade width 6 mixing time H viscosity of fluid p density of fluid
2.1 Singl* phase
91
Khang, S. J. and Levenspiel, 0., Chem. Eng. Sci., 31,569 (1976) New Scale-up and Design Method for Stirrer Agitated Batch Mixing Vessels Experimental apparatus System Vessel Type Diameter (m) Height (m) Baffle Number Impeller Type Diameter (m) Number of impellers Number of blades on impeller
(1)
(2)
flat-bottomed 0.559 0.559
flat-bottomed 1.219 1.219
4
4
turbine 0.127,0.244 1 6
d:i:w Pitch/Diameter Off-bottom clearance
propeller 0.114,0.254 1 3
turbine 0.366,0.488 1 6
propeller 0.114,0.254 1 3
20:5 : 4 1.5/1 0.610
0.280
Working fluids Water and 70% aqueous solution of glycerin Experimental conditions Re>10^ Measurement technique Conductivity measurement Results For turbines \2J3
pn d ropeUers For propeUers ^Pgc ^ = 0.9 pn'd' Notation d stirrer diameter, m D tank diameter, m Newton's-law conversion factor gr K amplitude decay rate constant, 1/sec length of impeller blade (perpendicular to i shaft) stirrer rotational speed, 1/sec
P Re w /i p
mixing power requirement, W stirrer Reynolds number, nd^p/n, dimensionless width of impeller blade (parallel to shaft), m viscosity, g/msec density, kg/m^
Chapter 2. Mixing tiin*
92
Shiue, S. J. and Wong, C. W, Can. J. ofChem. Eng., 62,602 (1984) Studies on Homogenization Efficiency of Various Agitators in Liquid Blending Experimental apparatus Vessel Type: dish-bottomed Diameter: 0.4 m Baffle Number: 4 Width: 0.04 m Agitator Agitator
D/T
LID
W/D
DalD
d
C/HL
6-Fiat blade turbine
0.325 0.362 0.450 0.325 0.325 0.325 0.325
0.25 0.241 0.222 0.25 0.231 0.423 0.346
0.20 0.207 0.194 0.20 0.269 0.154 0.231
0.667 0.690 0.667 0.667 0.769
0.5 0.5 0.5
— —
— — — —
45'> 45**
0.325 0.325
0.346 0.346
0.231 0.231
— —
45**
45°
0.5 0.5
0.325 0.325
0.346 0.50
0.231 0.231
— —
45** 25**
0.5 0.5
6-Curved blade turbine 4-Curved blade open style turlrine 4-Pitched Wade turbine 4-Pitched Wade turbine with a draught tube 2-Pitched blade turbine 2-Pitched blade turbine with a draught tube VEGYTERVpropeUer
I ^—^-^ I Six-flat blade turbine
I ^—^r-^ I Sbc-curved blade turbine
4-Curved blade open style turbine
«c:^^5:o 3-Wade VEGYTERV propeller
4 & 2-pitched blade turbine Various types of agitators.
0.325
0.5 0.5 0.5
2.1
93
Working fluids and their physical properties Tap water, glycerin solutions, and com syrup solutions Physicochemical properties of liquids Liquid
Viscosity (Ns/m^xlO^)
Density (kg/m^)
0.894 4.75 9.90 31.52 14.56 61.70 408.74
997.1 1,122.8 1,158.1 1,197.2 1,185.4 1,249.5 1,312.8
Water Glycerin 45 volume % Glycerin 60 volume % Glycerin 75 volume % Com symp 45 volume % Com symp 60 volume % Com symp 75 volume % Results -I
1—I—r-
1 6-Curved| 4-Curved
•WeF pigcerln.
g
^
pm syrup
mw%
•ot iU^^^?j 10^ 2
4
6
8 10
4
6
8 10^^
4
6
8 10=
Re
Homogenization number as a function of Reynolds number: (1) 6-curved blade tiurbine, (2) 4K:urved blade open-style turbine (J)/T=0325, C/HL=0.5).
Chapter 2. Mixing time
94
n
i—i—I r r T I
1
1
1
I I r t ! •
•nrri
T
-A—
Wafer ^Vbl % Glycerine eoN^iyo
V
a
A T
7S^W%
10-
I
«Vbl% Com syrup 60\^l % 75Vbl%
• 0 1
Data of Havaset al."'''^' ' — D/T = 0.254, C / H L = 0.5 — 0 / T = 0.382. C / H L : 0.5 1
^jjSZjTSZSaj^—^—AAA A A A A ^
1,
10^2
I
681?
2
4
681?
2
t
>
Z
I
I
li
I
6 8 10^
2
Homogenization number as a function of Reynolds numberS-blade VEGYTERV propeller (Z)/r=0.325,
C/HL=0.5).
•I
T""
2
1
I
» » I I !•'
4 1 J-Pitched 1 4-Pitched 2-Pirched 4-Pitched »Ofauq^li] a A r V^ter • • A a A5Vbl% • Glycerine 60Vbl% B 1 o A • V • O 1 75Vbl*/o o V e • 1 SW5? m Gxn syrup A 1 A (D •• A 0 B 1 TSJE*
— 5 —
mw%
10 Ho
•
B K ^ c»^o^^B6v<37^\;^,n Op n ^
I . . . .Dafa Of Hyas et al.t^'^fl >6-Pitched blade TUrbfie D/T = 0.333 C/HL= 0.5 .—• ' > • • • • . . ^-.-.^-..-.-^...u^ . c 10 1?2 4 681? 2 4 6 8 1 0 ' 4 6 8 lO-*
|
Re Homogenization number as a function of Reynolds numben(l) 4-pitched blade turbine, (2) 2-pitched blade turbine, (3) 4-pitched blade turbine with a draught tube, (4) 2-pitched blade turbine with a draught tube (D/r=0.325,C//fi.=0.5).
2.1 SingI* phas«
Notation C distance between the impeller and the bottom of the tank, m D impeller diameter, m Dd impeller disk diameter, m HL liquid height, m Ho homogenization number, Ntm, dimensionless L length of impeller blade, m N impeller speed, 1/sec Re Reynolds number, ND^p/fi, dimensionless tm mixing time, sec T tank diameter, m W width of impeller blade, m 0 impeller blade angle, degree /I impeller viscosity, Nsec/m^ p impeller density, kg/m^
95
Chapter 2. Mixing tim*
96
Sano, Y. and Usui, H.,/. Chem. Eng. Japan, 18,47 (1985) Interrelations among Mixing Time^ Power Number and Discharge Flow Rate Number in Baffled Mixing Vessels Experimental apparatus Vessel Type: (1) (2) flat-bottomed Diameter (1)0.2 (2) 0.4 m Liquid contained Height: (1)0.2 (2) 0.4 m Baffle Number: (1) (2) 4 Width: (1)0.02 (2) 0.04 m Impeller Type d/D b/D np
turbine 0.4,0.5,0.6,0.7 0.1,0.15,0.2,0.3,0.4 2,4,6,8
paddle 0.3,0.4,0.5,0.6,0.7 0.05,0.10.0.15,0.20,0.30 2,4,6
Working fluid Tap water Experimental conditions 0.3 < d/D < 0.7 0.05 < b/D < 0.3 2 < w> < 8 Re>5x 10^ Measurement technique Measurement of electrical conductivity Results For paddles
1
i
1 d
Turbine (a: c: d = 5 : 2: 20)
neM= 2.1 (d/D)-'-^ ib/D)-^'^ nf^'' For turbines nftv= 3.8(rf/Z))-^«° (b/D)-"^' ni^'*' Notation a impeller length, m b impeller width, m c thickness of impeller disk, m d impeller diameter, m D vessel diameter, m n impeller rotational speed, 1/sec np number of impeller blades Re impeller Reynolds number, d ^n/v, dimensionless 6M mixing time, sec V kinematic viscosity of liquid, mVsec p liquid density, kg/m^
1
ch-
^J1 11' .,
Paddle
»- a - ^
1 -
•
1
2.1 S i n g I * plMis«
97
Takahashi, K., Yokota, T. and Konno, H.,/. Chem. Eng. Japan, 21,63 (1988) Mixing of Pseudoplastic Liquid in a Vessel Equipped with a Variety of HeUcal Ribbon Impellers Experimental apparatus Vessel and impeller geometries Vessel type: flat-bottomed Impeller type: helical ribbon ds ' "'""
Geometrical variables for helical-impellers
t
Bn
Geometry No. d (mm)
"7^
DHl DH2 DH3 DH4 DH5 DH6 DH7
::
X V)
1 ? z—i
d D
95.9 88.5 82.0 91.0 90.3 90.4 91.9
c/D
s/D
w/D
0.0208 0.0574 0.0900 0.0450 0.0482 0.0482 0.0405
0.926 0.909 0.912 0.621 0.455 0.930 0.921
0.100 0.100 0.100 0.100 0.100 0.152 0.200
D=H=100 mm, «^=2, rf,/Z)=0.0938
General configuration of a helicalribbonimpeller
Working fluids and their physical properties Liquid
n(-)
X(Pas")
3wt%HEC 4wt%HEC 5wt%HEC Com symp
0.768-0.832 0.718-'0.761 0.686-0.735 1
0.724-1.56 2.76-4.60 7.06-14.1 0.550-3.33
Results 0.405^rf/D^ 0.574, 0.455 <5/Z)< 0.930, 0.100
Notation A a function of geometrical variables c clearance between blades and wall, m d diameter of impeller, m ds diameter of shaft, m D diameter of vessel, m h height of impeller, m H height of vessel, m K consistency index, Pa(secy n flow behavior index, dimensionless
rotational speed of impeller, 1/sec circulationflowrate, mVsec Rea apparent Reynolds number, d^Nplpia, dimensionless impeller pitch, m s mixing time, sec tm W blade width, m apparent viscosity, Pa-sec ^ density, kg/m^ P
N
Qi
Chapter 2. Mixing tima
98
Saito, E and Kamiwano, M.J. Chem. Eng. Japan, 22,491 (1989) An Extended Technique for Predicting the Mixing Times of HighViscosity Liquid in a Mixer—Mixing Systems with Molecular Diffusion of Solute— Experimental apparatus Vessel Type: (1) flat-bottomed helical screw/draft tube mixer (2) flat-bottomed helicalribbon-impellermixer
Impeller
(1) Screw impeller mixer
(2) Helicalribbonimpeller mixer
(1) Screw impeller mixer with draft tube
D(mm)
D'(mm)
(/(mm)
H(xnm )
H' (mm)
/t(nun)
100 (Do) 150 200
68 103 137
67 100 133
150 225 300
100 150 200
117 175 233
(2) Helicalribbonimpeller mixer D(mm)
d(mm)
^(mm)
^(mm)
u;(mm)
75 (Do) 100 150
64 86 131
80 108 163
70 94 142
9 12 18
Working fluids and their physical properties Fluids: com syrup and PVA aqueous solutions (viscosities = 0.35-1.5 Pasec at 291K) Solutes: KCl and fluorescein sodium (C2oH2oNa205)
2.1 Single phase
99
Results
n
[s-^]
Variation of/« with n for helical screw/draft tube mixers (PVA aque. solu.-C2oHioNa205)
Notation Do n tm im
inner diameter of reference vessel, mm rotational speed of impeller, 1/sec mixing time, sec arithmetric mean of mixing time, sec
Variation of tm with n for helical ribbon impeller mixers (a) PVA aque. solu.-C2oHioNa205 (b) Com syrup-KCl
Chapter 2. Mixing tini*
100
Saito, E, Aral, K. and Kamiwano, M.J. Chem. Eng. Japan, 23,222 (1990) An Extended Technique for Predicting the Mixing Times of HighViscosity Liquid in a Mixer—Mixing Systems with Molecular Diffusion and Reaction of SolutesExperimental apparatus Vessel and mixer T3rpe: (1) flat-bottomed helical screw/draft tube mixer (d/D=0£7) (2) flat-bottomed helicalribbon-impellermixer (d/D=0.S6) Diameter: 75,100,150, and 200 mm
Vessel and impeller geometries
(2) Helicalribonimpellermixer
(1) Screwimpellermixer (1) Screw impeller mixer with draft tube D(mm) 75 (Do)
100 150 200
D'(mm)
d(mm)
51 68 103 137
50 67 100 133
H(mm) 113 150 225 300
^'(mm)
h(mm)
75 100 150 200
88 117 175 233
(2) Helicalribbonimpeller mixer
D(mm) 75 (Do)
100 150 200
^(mm)
H(mm)
h(mm)
w{mm)
64 86 131 172
80 108 163 216
70 94 142 188
9 12 18 24
2.1 Singl«phas«
101
Working fluids and their physical properties Com syrups: viscosities = 0,6—1.6 Pa-sec at 291K Measurement technique Use of chemical reactions I2 + NaaSzOa -^ Nal + Na2S406 I2 + NaaHPO* - Nal +NaHP04 Results 10^
i m — Colculoled Vfllu ft
Hi
1
10"'
U
(A)
Measured Value
[TCeyj Dlmmllj 0 75 m 100 Hill Lc 150 10^ [ teUtllL eTf200 Ip itj =Fn 1ft i m ^ I ti p^ztzfc in
— Colculoted Volue I Measured Value
1111
loo
m
y
10^
k e y DInvnl
tfcS T
(B)
|L HJI
IP
1 N [S'h
l-H
^ ^
»b
mL fflt^
10"
100 j
€ 150 1 0 200
i 1 h
10'
75
•
m
^
YvUII
[vrvjN
3
10-^ 10'
Variation of mixing time with rotational speed of impeller for h and Na2S203 reaction system: (A), helical-screw/draft tube mixers, Uquid; //=0.3 Pas;.(B), helicalribbon-impellermixers, liquid; ;i=0.5 Pa s
Variation of mixing time with rotational speed of impeller for liquid of/i=0.5 Pas in helical ribbonimpeller mixers: (A) I2 + 2Na2S203 -^ 2NaI + Na2S406; (B) I2 + 2Na2HP04 ~^ 2NaI +NaHP04 DImml
reo ction system corn syrup
0 1200 75 1 15 0 € 0
1 ^^ [^ Na2S203 N02HPO4
& [dKfusion system
,
^
a 1 t 1Q Olmml
in corn syrup
150
A • ' •
M C 2 C •HioNa205
1 1 lllll
10^ Notation d impeller diameter, m D imier diameter of vessel, m Do imier diameter of reference vessel, m N rotational speed of impeller, 1/sec Re Reynolds number, pNdVfi, dimensionless tm mixing time, sec ^ viscosity, Pasec p density, kg/w?
10^
1 N (S-
10"
U-L '
Lsfe^yJAA-nil
I'll
MM
i^M
\ "\ \ \
1
.^^
A
Jr^^^
Jjil
—UU
•
i TT
~'
1"^^ir^i>~QD-«^"'^ (Jn
10^ 5
10°
(f (|( \
HHiii 1 ill i i IIII
11 1i l l !III 10==
10' Re 1-1
Variation of (A/if,) with Re for different mixing systems
Chapter 2. Mixing tiiiM
102
Carreau, P. J., P&ris., J. and Gu6rin, P., Can. J. ofChem. Eng., 70,1071 (1992) Mixing of Newtonian and Non-Newtonian Liquids: Screw Agitator and Draft Coil System. Experimental apparatus Vessel and impeller geometries
Path 1
Path 2
Path 3
Sketch of the mixing system.
System geometry (All dimensions in meters) 1. Vessel: Z)=0.254,/f=0.262(Cl), 0.255(C2), 0.261(C3) 2. Agitator d=0.150, A=0.220,/>=0.147, w=0.067,rf„=0.0159,Cba=0 012 3. Coils Name
Material
dc
he
du
dti
Cbc
ec
tic
CI C2 C3
Cr plated Cu Steel Copper
0.1827 0.1763 0.1887
0.205 0.2075 0.2175
0.0127(1/2") 0.00635(3/4") 0.00476(3/16")
0.0095 0.0043 0.0032
0.0275 0.0285 0.0175
0.0060 0.0064 0.0065
10.5 16.5 19.5
Characteristic parameters: D/d=l.e9, p/d=OM, A/rf=1.47, w/d=0A5,rf„/rf=0.106,Cba/d=OM,
2.1 SingI* phas«
103
Working fluids and their physical properties Properties of experimental liquids iu(Pas) n k P (kg/m^) (W/mK) Substance or m (Pas") (-) — 0.14 1.0 Glycerol 1,232. 0.213 1,235. 0.320 0.275 1,240. 0.315 0.310 0.408 1,246. 1,255. — 0.598 Vitrae oil HV32 0.055 856. 0.145 Mixture 0.200 873. 0.785 885. HV320 «• \w 2.48 1,383. 0.323 Com syrup CMC 1.0 0.564 0.748 996. 0.588 2.0 9.5 0.631 996. 0.575 Xanthan 0.75 6.27 0.122 995. 0.610 1.0 6.5 0.196 ^ 1.5 8.62 0.183 600mg/L 1,195. 0.356 Polyacrylamide 0.136 0.871 0.2 0.734 0.521 1.0 0.521 5.04 *Adjusted for desired viscosity. **Com syrup slightly diluted to avoid crystallization. Properties of distilled water used for solutions: //=9 x 10" Pa s, p=995.4 kg/m^ ife =0.610 W/mK, Cp=417J/kgK. Results (1) Mixing time Cone. (mass %) 89.0 91.5 93.5 95.0 97.5 100. * 100.
i
1
i 1
1
Cp
g/kg-K) — 2,515 2,480 2,451 — 1,901
1
2,358 4,177
1
1T
2,902
_J_
(Nt„U/(NL)N = 1+3.76 Wi"'*^ 0m<Wi<0.5 Ntn. = 62.4 - 35.3 [1 - exp (-0.0196i?e)] Wi = Ni/2r]q (2) Power consumption iy^/a=i200i?^;'(i+354.8m'-'') where Ci is given by : a = {0.124 + 0.265 [1 - exp (-0.008367?^^)]} (1 - 0.811 Wi""^^) Notation Cp specific heat at constant pressure, J/kg*K d agitator diameter, m k thermal conductivity, W/mK ks Metzner-Otto constant, dimensionless m power law parameter, Pasec" n power-law index, dimensionless N rotational speed, 1/sec Np power number, dimensionless Ni primary normal stress differences. Pa Re Reynolds number, d^Np/fX, dimensionless Rcg generalized Reynolds number, pN^'^^dVinks*"'^, dimensionless
Wi 1
p
mixing time, sec Weissenbeig number, Nil2r]qy dimensionless shear rate, 1/sec viscosity of non-Newtonian liquids, Pasec viscosity of Newtonian liquids, Pasec liquid density, kg/m^
Subscripts N Newtonian nN non-Newtonian
204
Chapter 2. Mixing tim«
2.2 Multi phase 2.2.1 Solid-liquid systems Raghav Rao, K. S. M. S. and Joshi, J. B., Chem. Eng.J., 39, 111 (1988) Liquid-Phase Mixing and Power Consumption in Mechanically Agitated Solid-Liquid Contactors Experimental apparatus Vessel Type: (1) (2) flat-bottomed Diameter: (1) 0.57 (2) 1.0 m Liquid contained Height: (1)0.57 (2) 1.0 m Baffle Number: (1) (2) 4 Width: (1)0.057 (2) 0.10 m Impeller DT 0.19
Type Diameter (m)
D/5 Vertical blade height (m) Horizontal blade length (m) D/i — Angle of pitch (degree) Blade thickness (m) 3x10-' 4x10-3 Disk thickness (m) Number of impellers 1 Number of blades on impeller 6 Off-bottom clearance DT: disc turbine PTD: pitched blade turbine downflow PTU: pitched blade turbine upflow
PTD 0.1425,0.19,0.25,0.33
PTU 0.19
0.03,0.04,0.063,0.07 0.045,0.075,0.10,0.14 45,45,45,45 3x10-' — 1 6 r/6, r/4, r/3, r/2
0.04 0.075 45 3x10-' — 1 6
Working fluid, and solid and its physical properties Liquid: tap water Solid: quartz particles shape: granular average particle size: 100-2,000 ^m density: 2,520 kg/m' terminal settling velocity in water: 34—165 mm/sec Experimental conditions ImpeUer speed: 2—13.3 rps Solid loading 0-40 wt% Results For PTD JI0L32
0.19
J0.11
(Ar0)as=cr"d,"
2.2 Multi phas«
Notation C impeller clearancefrombottom, m dp D N Ncs T X 9 (AT^cs
average particle size, ^m impeller diameter, m impeller rotation speed, 1/sec critical impeller speed for solid suspension (solid-liquid system), 1/sec tank diameter, m solid loading, wt% mixing time, sec dimensionless mixing time at critical suspension
^Q5
206
Chapter 2. Mixing tim«
Kraume, M., Chem. Eng. TechnoL, 15,313 (1992) Mixing Times in Stirred Suspensions Experimental apparatus Vessel Type: dish-bottomed Diameter: (1) 0.1 (2) 0.33 (3) 1.0 m Liquid contained Height:(l) 0.1 (2) 0.33 (3) 1.0 m Baffle Number: (l)'-'(3) 4 Width: (1) 0.01 (2) 0.033 (3) 0.1 m Immersed depth: (1)~(3) 0.8 D Impeller Type: (a) disk turbine (b) propeller (c) pitched blade turbine Diameter: rf/Z)=0.19~0.6 Number of impellers: 1 Off-bottom clearance: h/D=0,l7 Working fluids, solids and their physical properties Liquid: water and polyvinyl pyrrolidone solutions (viscosities = 12 and 50 mPasec) Solid: three kinds of glass beads (mean diameters = 0.09,0.37 and 1.5 mm) Experimental conditions Impeller speed: 100-1,200 rpm Solid concentration: 1.6—16 % Results T 332) -JgDws Notation d agitator diameter, m D vessel diameter, m g gravitational acceleration, m/sec^ h stirrer clearance, m TM. 90% mixing time for 90% slurry height criterion, sec Ws settling velocity of single particle, m/sec
2.2 Multi phas«
^07
2.2.2 Gas-liquid systems Einsele, A. and Finn, R. K., Ind. Eng. Chem. Process Des. Dev., 19,600, (1980) Influence of Gas Flow Rates and Gas Holdup on Blending Efficiency in Stirred Tanks Experimental apparatus Vessel Tank diameter (m) Liquid volume {i) htlT Baffle Number WBIT
Impeller Type Number of impellers Number of blades on impeller Speed (1/sec) Air sparger Type Number of holes Hole diameter (nmi) sIT Aeration rate (mVsec)
small vessel
large vessel
0.285 20.0 1.05
0.756 350.0 1.01
4 0.09
4 0.10
six-blade disk turbine 1 6 3.33-15.00
six-blade disk turbine 1 6 2.50-7.50
ring 12 0.4 0.20 0.0-0.5
ring 13 3.0 0.18 0.0-1.52
Working fluids and their physical properties Liquids: see table Physicochemical properties of aqueous phases (25°C) viscosity" surface tension, liquid/solution Pas 10^ (N/m) x 10^ water 0.80 72.0 glycerol (70 wt%) 70.0 63.1 glucose (50 wt%) 7.0 70.0 glucose (70 wt%) 11.0 71.2 Natrosol250H(0.5wt%) 185.0 (12 rpm)' 65.2 Natrosol250H(1.0wt%) 240.0 (12 rpm)' 64.0 Cellosize QP300 (1.0 wt%) 30.0 (60 rpm)" 67.0 Cellosize QP300 (2.1 wt%) 310.0 (12 rpm)' 65.0 Cellosize QP300 (2.6 wt%) 610.0 ( 6 rpm)' 64.0 "The rpm in parenthesis refer to the Brookfield LVT measurement with spindle no.L Gas: air
108
Chapter 2. Mixing time
Results For0.8X 10-3 < / / < 0.61 Pasec ^^^j 0 = o.O~O.16 (1) the small vessel r « / r . = l + 13.O(jur-^(0) (2) the large vessel r . / r « = 1 + 7.5 Ox)°-2^(0)
Notation hi s T Ta T„ WB /J. 0
deal liquid height above tank bottom, m gas sparger diameter, m tank internal diameter, m blending time under aerated conditions, sec blending time under non-aerated conditions, sec baffle width viscosity, P a s e c gas holdup volume fraction
2.2 MuHi phase
109
Joshi, J. B., Pindit, A. B. and Sharma, M. M., Chem. Eng. Sa., 37,813 (1982) Review Article Number 7 Mechanically Agitated Gas—Liquid Reactors Results Use of results obtained by Van der Molen et al (1) and Hughmark (2) for flat blade turbine Ne = 20Al
H
+1
'''''^ N'D' ^''''
\D)
[D)[NV)
[gwv^
(1) Van der Molen, K. and Van Mannen, H. R. E., Chem. Eng, Sci., 33,1161 (1978) (2) Hughmark, G., Ind, Eng. Chem. Process Des. Dev., 19,638 (1980) Notation D diameter of the impeller, m g acceleration due to gravity, ml sec? H height of clear hquid, m N impeller speed, r/s Qg volumetric gas flow rate, mVsec T diameter of vessel, m V volume of liquid, m^ W impeller blade width, m 6 mixing time, sec
Chapter 2. Mixing tiiiMi
110
Pandit, A. B. and Joshi, J. B., Chem. Eng. Scu, 38,1189 (1983) Mixing in Mechanically Agitated Gas—Liquid Contactors^ Bubble Columns and Modified Bubble Columns Experimental apparatus Vessel, impeller, and sparger geometries Impeller details T^^,_^ Diameter ^^ Z)(m) i)Sixbladed 0.103 disk turbine
Vessel
diameter r(m) 0.305
1.00
*ii) Propeller *iii) Pitched blade turbine i)Sixbladed disk turbine ii) Curved blade iii) Pitched blade turbine
0.101 0.101 5 blades 0.34
Sparger type
Li/D 0.25
W/D 0.2
Hi/H
0.33 and 0.50 ^/
Single point and 5 point hole dia = 2.5 mm
0.25
0.2
0.33
Sieve plate sparger 98 holes, hole dia = 2.5 mm
0.34 0.34
^Upward and downwardflowpatterns were studied.
Working fluids Liquid: water Gas: air
Experimental conditions Impeller speed: 3—25 rps Superficial gas velocity: 0—25 mm/sec Results For six bladed disk turbine
(yolec)
= 0.865
NO = THAI
(BI
aH + T D)
[D)(NV)
[gWV'"
Notation a a = l, when impeller is centrally located D diameter of the impeller, m acceleration due to gravity, m/sec^ g H hquid height in mechanically agitated column. m Hi height of impeller from the tank bottom, m Li length of impeller bhde, m N impeller speed, 1/sec
Ner QG
T V Vc W EG
e
critical impeller speed for gas-phase dispersion, 1/sec volumetric gasflowrate, mVsec tank diameter, m total volume of liquid, m^ gas superficial velocity, m/sec width of impeller bhde, m fractional gas hold-up time, sec
2.2 Multiphase
111
Abrardi, V, Rovero, G., Baldi, G., Sicardi, S. and Conti, R., Trans. Instn. Chem. Engrs., 68, P&rt A, 516 (1990) Hydrodynamics of a Gas-Liquid Reactor Stirred with a Mtdti-Impeller System Experimental apparatus Vessel and impellers Vessel Type Diameter (cm) Liquid contained Height (m) Baffle Number Width (m) Impeller Type
flat-bottomed 0.39
flat-bottomed 0.39
0.39
0.65
4 0.04
4 0.04
6DT, 4MFD, 4MFU
6DT-6DT,6DT-4MFD, 6DT.4MFU T/3 2
Diameter (m) T/3 Number of impellers 1 Positions of impellers Distance between bottom T/3 and thefirstimpeller Distance between 1st — impeller and the second impeller 6DT: six-blade disk turbine 4MFD: pitched blade mixed flow turbine, pumping downward 4MFU: pitched blade mixedflowturbine, pumping upward Sparger Number of holes: 8 ID of hole: 2 nmi Location: beneath the stirrer Working fluids Liquids: water Gas: air Experimental conditions Gasflowrate: 5 x 10-*~2 x 10"^ mVsec Stirrer speed: 150-800 rpm
T/3 2T/3
Chapter 2. Mixing time
112 Results 40 (S)
/
30
20
/
K/
K 5^^ t
0
.1
i
.2
l
.3
l
.4
.5
1/N(») Mixing time vs UN as a function of QG for the 6DT-4MFD system-A: 7.67 lO"'' mVs; D: 1.0710-^ mVs; 0:210"^ mVs; — : Qc = 0.
Mixing time vs 1/iVas a function of QG for the ): QG = 0; A: 6DT-4MFU system- • ( 7.67 lO-" mVs; D: 1.6710"^ mVs; 0:210"^ mVs
N (S) Mixing time in ungassed systems-A: 6DT-6DT; • : 6DT-4MFD • : 6DT-4MFU;
Notation N stirrer velocity, 1/sec IM mixing time, sec T tank diameter, m
: 6DT single impeller.
2.2 MultiplMiM
113
Satoh, K., Menju, T, Mochizuki, M. and Shono, A., Kagaku Kogaku Ronbunshu, 21,137 (1995) Mixing Times of Liquids in Gas-Liquid Contactors with Mechanical Agitation Experimental apparatus Vessel Type: flat-bottomed Diameter: 29 cm Liquid contained Height: 29 cm under migassed conditions Baffle Number: 4 Width: 2.9 cm Impeller Type Diameter (cm) Number of impellers Number of blades on impeller Off-bottom clearance
6DT 8,10,13.5,15 1 6 H/5
6MDT-1 10 1 6 H/5
DT: disc turbine
B^^3I>F£) Sparger ^^^ Type: 20 hole nozzle Nozzle diameter: 8 mm Nozzle height: 26 nmi Hole diameter: 1 nmi Location: directly below the impeller
Working fluids Liquid: tap water Gas: air
Experimental conditions Volumetric gas velocity: 0—1.3 dmVsec Impeller speed: 0-15 1/sec Temperature: 20°C Pressure: 1.01 atm
6MDT-1
^ 6MDT-2
6MDT-2 10 1 6 H/5
^24
Chapter 2. Mixing time
Results
iien.^{{iieaf-^r\{iie,)y =Ka/pDY\Pc.f' K = iiC.{0.230(4/7r)}'^' = 0249Ka
K„.=(KJ0,mKa)H4/7c){N^/Np)(d/D)\D/Hf =
imxlO\K,/Ka)\Ni/Np)(d/D)\D/H)'
Notation d diameter of impeller, m D diameter of vessel, m H liquid depth in vessel without aeration, m K proportional coefficient Ka Proportional coefficient Kg Proportional coefficient Np power number, dimensionless Nqd discharge flow number, dimensionless Pp agitation power input per unit volume of liquid without aeration, w/w? Pap aeration power input per unit volume of liquid, w/m^ Pcp effective power input per unit volume of liquid, w/m^ 77 coefficient da mixing time under aeration without mechanical agitation, sec Og mixing time under mechanical agitation without aeration, sec 6m mixing time under mechanical agitation with aeration, sec Km coefficient p density offluid,kg/m^
2.2 Multi phase
125
Nienow, A. W, Trans. Instn. Chem. Engrs., 74, P&rt A, 417 (1996) Gas-Liquid Mixing Studies: A Comparison of Rushton Turbines with Some Modem Impellers Results Based on the studies at BHR"^
or 'S/S/:; \ - i / 3 0»=5.9r''(er)
(fl
with T^H *Ruszkowski, S., 1994, A rational method for measuring blending performance and comparison of different impeller types, in Proc 8th Europ Mixing Conf, (IChemE, Rugby), 283-291. Grenville, R. K., Ruszkowski, S. and Garred, £., 1995, Blending of miscible liquids in the turbulent and transitional regimes, 15th NAMFMixifig Conference, Banff, Canada, Notation D impeller diameter H liquid height N impeller speed Po power input under gassed conditions T vessel diameter £T mean energy dissipation rate 6m mixing time
117
Chapter 3.
Power draw and consumption
3.1 Single phase Rushton, J. H., Costich, E. W and Everett, H. J., Chem. Eng. Progress, 46,395 (1950) Power Characteristics of Mixing Impellers Part 1 Rushton, J. H., Costich, E. W. and Everett, H. J., Chem. Eng. Progress, 46,467 (1950) Power Characteristics of Mixing Impellers Part 2
Experimental apparatus Vessel Type: flat-bottomed Baffle Number: 4 Impeller Type: propeller,flat-bladeturbine, curved blade turbine, shrouded curved blade turbine with stator ring, and arrowhead turbine
Arrowhead Turbine
Flat Blade Turbine
Curved Blade Turbine
Working fluids and their physical properties Fluid water kerosene-carbon tetrachloride mixtures lubricating oil Unseed oils corn-syrup solutions
Viscosity (cP)
Density (lb/ft3)
about 1 5-600 5-600 800-20,000 15-43,000
59.7-90 • • •
Shrouded Curved Blade Turbine with Stator Ring
^
.
10
• • • • •
s
• 4 It 4 4
M. IN. IH W. M.
• • • • •
• IN. 4 M. ll.aiN. • M. 3 IN.
• • • • •
m IN IN M IN
II IS 34 13 13
m. m. M. m. IN.
• • • • •
T/O • 3.0 T / D • 3.3 T/O • 4.3 T/D • 3.3 MFFLES Okl T
c
..<
1.0 VALUES OF
(
— nioraLLnu, NO MFFLes 03
KLOW
.
—
_
1
1 ^ OF 3 0 0 ,
I
• ^
^5^; WITH lAFFLESt FOR ALL N ^
•*-!
...
} • *F
1 1 1 1 nil 1
9
1
g
1
f
»"
I0>
REYNOLDS
NUMBER
Np, .
«
w* P^^/?
Reynolds Number Correlation for Propellers.
t
a
a
fl
I
r i f
100
^
90
"
IN. DMMETCR ( FLAT ( L * D t ANK OIAHETCR I t IN. 7VRUNE • IN. • M V C KTrOM lOUID DEPTH I t IN.
t
VE
1 t
MFFLEt •
4
NO lAFFLEI
3
•
•
1
EACH •
•
•
I
TUIWINC
4 % TANK DMMETEII 10 » •
.IT* f
-it-MlU
' "V* "nT
l
^
10 "* S
1
• « ^ » > i ^ - i
p;'
"
s i
111
» o
^'iu^
a. t
1
t
I
i
B
«•
t
9
»• REYNOLDS
NUMBER
D'N/
Reynolds Number Correlation for a Flat Blade Turbine. •O
t
^
5''^§|:^'^
OP
1 ?• fS^ ggg'l'S S'i-'9 §'i s 11 11: g'-c S «1 3
SB.
CO
»
^1- ^ 1
If
'IP 1 s.
3 re n
•1
I
»'
s
t
ft
Chapter 3. Power draw and consumption
120
Metzner, A. B. and Otto, R. E.,AIChE Journal, 3,3 (1957) Agitation of Non-Newtonian Fluid Experimental apparatus Vessel Type: flat-bottomed Diameter: 6-22 in Baffle Number: 4 or 0 Width: 0.1 T Impeller Type: six-flat bladed turbine Diameter: 2—8 in 1.3—3.7 T/D ratio: laminar region transition region 2.0—5.5 Number of impellers: 1 Number of blades on impeller: 6
Working fluids and their physical properties Sodium carboxymethyl cellulose (CMC), Carbopol 934 and a suspension of Attasol Apparent viscosity = 7—180 poises
Experimental conditions Power input: 0.5-176 hp/1,000 gal Rotational speed: 95—1,190 rpm Reynolds number: 2.0-270
Results 1
1 1
ill i ii
11
III
1
III
' — 1r -
* t \
i l_
U
Notation D impeller diameter, ft gc
N P fia
P
conversion foctor, Ibm'ft/Wf'sed^ rotational speed, 1/sec power, ft'lbf/sec apparent viscosity, Ibnt/ft density, Ibm/f^
III
1
III
1
1^
'
' ! iSi- 1 1 i 1 "^Q^iij^
• i "
/l/,*" M l
I I I , j > i r i•*^A'U
M A t.e % CMC » CMC k CM O ATTJM L
1
III
iV!f^vi^
1
ijSBSf^BT-l
F ' ii A!
M
iT i1
Power-number-Reynolds-number curve for non-Newtonian fluids; all points in the crowded regions were not shown.
3.1 Single phas«
Metzner, A. B., Feehs, R. H., Ramos. H. L, Otto, R. E. and Tuthill, J. D., AIChE Journal 7,3 (1961) Agitation of Viscous Newtonian and Non-Newtonian Fluids Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.5-1.83 ft Baffle Number: 4 or 0 Width: 0.1 T Impeller Type:flatbladed turbine Diameter: 0.167-0.67 ft TID ratio: laminar region 1.3—5.5 transition region 2.0—5.5 Number of impellers: 1 Working fluids and their physical properties CMC, Attasol, Carobopol, Permagel and Pliovic Flow-behavior index 0.2—1.5 Apparent viscosity 1—180 poises Experimental conditions Power input: 0.4-176 hp/1,000 gal Impeller speed: 1.58—29 rev/sec Reynolds number: 2-1,760 Apparent viscosity: 1—180 poises
121
Chapter 3. Power draw and consumption
122
Results
1000
REYNOLDS NUMBER. D^Up/p,
Symbol
o
V
D
•
A A
O V
<2>
Fluid CMC Attasol Carbopol Carbopol Carbopol Carbopol Permagel Permagel Pliovic
n 0.34 0.38 0.26 0.20--0.26 0.30-0.54 0.18-0.29 0.16 0.21 1.5
Power number-Reynolds number correlation for non-Newtonianfluids:single,flatbladed turbine.
Notation D impeller diameter, ft gr dimensional conversion factor 32.2 ftlbM/sec^lbF n flow behavior index of a non-Newtonian fluid, dimensionless N rotational speed of impeller, 1/sec P power consumption, ft/6f/sec T tank diameter, ft /I viscosity, IbM/secft, //«is sometimes used to emphasize that the viscosity (or apparent viscosity of a non-Newtonian fluid is a function of shear rate) p density, Ibm/ft^
3.1 Singl* pluis«
123
Metzner, A. B., Feehs, R. H., Ramos. H. L, Otto, R. E. and Tuthill, J. D., AIChE Journal 7,3 (1961) Agitation of Viscous Newtonian and Non-Newtonian Fluids 1. Two flat-bladed turbines (1) Ranges of variables covered Variable T D T/D n M N
(ft.) (ft.) (poises) (rev./sec.)
NRe
Power dissipation (hp./l,000gal.)
Newtonian data
Non-Nertonian data
0.469-1.166 0.33'-1.00 1.023-3.50 1.0 1.48-184 0.03-16.8 0.10-480 0.04-230
0.469-1.166 0.33-1.00 1.023-3.50 0.14-0.72 2.41-200 0.08-17.3 0.146-620 0.06-175
Baffles, used as indicated on thefiguers,were of a width equal to 1/10 T,
(2) Results
1.0
10
100
REYNOLDS NUMBER, O ^ N / » / M SYMBOLS, T / O
h^^< 1 1.000 1 0.666 1 0.500 1 0.333
Lt66
0.786
RATIOS
0.698
1
0.662
0.496
1
1.166 O 1.75 O ^ i.iS
O
L048
•
1.023
•
2.33 ^ A 1.57 ° B 1.39 <J 3.50 > • 2.36
• • A « ^ BAFFLED TANK
0^ 2.10 ^ T
1.41
<
O a O O V A O < UNBAFFLED TANK
Power number-Reynolds number correlation for Newtonianfluids:twoflat-bladedturbines: Curve A'Ax\ T/D > 1.25, baffled tanks, A-i42: T/D > 1.25, unbaffled. Curve B: T/D = 1.16-1.18, C: T/D = 1.02-1.05. Curves B and C join curves i4-i4i andi4-i42 as the Reynolds numbers increase.
Chapter 3. Pow«r draw and consumption
124 p»V.« ' : • nil! • • i i-4r \ U l | 11 ••vV 1 iS^llllI
=7TJ1 1 j
J_jjl
.
1 1
j III
ruiios cm^ ^ f
1 i 11
1
nil
1 1 j 1 i .•
1
Jill" T ^ g M^ %
i
1(11 1 11
ll|>i'JU^.A..
NCWTONI
i
} '
1 1 11
•vn(\
1
1 III
III
J»JJ
• •
is^¥@i 1
' '
J
a»i lllll
1 ^jVBwweK?' 1 J^
1
oj 1 1 li
II
lllll
REYNOLDS NUMBER., D ' N ^ / M
Power number-Reynolds number correlation for non-Newtonians-two flat-blade turbine impellers. See the above table for legend.
2. Fan turbines (1) Ranges of variables covered T D T/D n
(ft.) (ft.) (poises) (rev./sec.)
N NRe
Power dissipation (hp./l,000 gal.) No. of independent measurements
«<1
w= l
0.67-0.98 0.33-0.67 1.33-3.0 0.21-0.26 0.5-3.2 2.8-26 6.6-160 8.7-160 46
0.67-0.98 0.33-0.50 1.33-3.0 1.00 1.9-11 1.5-15 1.1-43 7.5-98 35
n>l 0.67-0.98 0.33-0.67 1.33-3.0 1.0-1.42 1.9-3.2 1.7-16 7.9-33 5.9-130 49
(2) Results
.NEWTONIAN (:URVE -y
j U IT
V
11 oA rswj
SYMBOL • • A V o O a V
n T/D 0.21-0.26 3.0 0.21-0.26 2.0 0.21-0.26 1.5 0.21-0.26 1.33 1.0 - 1.42 3.0 1.0-1.42 2.0 1.0 - 1.42 1.5 i.O - 1.42 1.33
IPI
I ii&«
nrSter ID
lu^Sfewm
lit
I
9
I
10
F
:i'
^ n • • 100
300
REYNOLDS NUMBER, O^Hp/^iQ
Power number-Reynolds number correlation for a six-bladed fan turbine.
3.1 S i n g l * p h a s «
125
3. Marine propellers (1) Ranges of variables covered
R 3
J ^
ill
f
B ^ ^
/
1/
SECTION A-A
SECTION B-B
Description of shaft position II used with the marine propellers.
T/D
Curve A B C D E
Shaft position
0.417 2.2'-4.8 0.417* 2.2-'4.8 1.00 1.9--2.0 1.00 1.9-2.0 Newtonians
I,n I,n II I II
Power number-Reynolds number correlation for square-pitch propellers (n < 1.0). Asterisks denote upward displacement of fluid. (2) Results too
1 j 1 1
)
j
f— j
1
11«
1 i ( t j !|
11 i^tn 1
1 1 1 M rS 1
1111 III
lO
10
^
1
1 1
lllll 1 Iff
*2 ^ j j 1
1 • 1 { j j 1 {• .
11°^ im
CL
m—H-HfnV 1 ' " ^ ! !
1\
bj
1.0 1 I Mill
S
7m5—^
o
MP=
^
j
o.t
IllJil J 1.0
10
^
Jjlj
100
j
In
III! III ^>fc,l
REYNOLDS NUMBER, D ^ N / y ^
1,000
10.000
Chapter 3.
126
Power d m w and consumpticm
4. Double-pitch propellers (1) Ranges of variables covered Shaft position Curve TID A B C
II I
1.4-3.0 1.4-3.0 Newtonians
n
Power number-Reynolds number correlation for double-pitch propellers {n < 1.0).
(2) Results 100
j1
1 i 11 iffl
SI
-.<^
h L
r-x< 1 10
j
^ -Uokc-I I n *!S
Ui
m
I I I i Oo«u:
* ill
Ilii ^'^iS^LL
3 Z
?ji Jtor:-
O
»^1
•' ! -
•
,1
1 ill
4L^ ^jt^ni
^
Q
1 1 11II 0.2
1.0
10
100 REYNOLDS NUMBER,
1 1nil 1 1,000 D^Hp/ft
Notation D impeller diameter, ft ge dimensional conversion factor, 32.2 MbAi/sec^lbF n flow behavior index of a non-Newtonian fluid, dimensionless N rotational speed of impeUer, 1/sec Niie Reynolds number, D ^Np/fi or D ^Np/fia, dimensionless P power consumption, ftlbF/sec T tank diameter, ft ^ viscosity, IbM/secft ^a apparent viscosity, /ftv/secft p density, Ibju/f^
10,000
3.1 Single phase
127
Godleski, E. S. and Smith, J. C.AIChE Journal, 8,617 (1962) Power Requirements and Blend Times in the Agitation of Pseudoplastic Fluids Experimental apparatus Vessel Type
flat-bottomed
Diameter (in) Liquid contained Height (in) Baffle Number Width (in) Clearance of bafflefromwall (in)
5.7
11.4
17.3
5.7
11.4
17.3
4or0 0.57 1/4
4or0 1.14 1/4
4or0 1.73 1/4
Impeller Type
standard six-flat blade turbine
Diameter (in) Number of impellers Number of blades on impeller
2 1 6
4 1 6
6 1 6
Working fluids and their physical properties Pseudoplastic fluids: Natrosol 250 H (high molecular weight solutions of cellulose) viscosity of 2% solution: 25,000 centipoises apparent viscosity: 1—100 poises n': 0.28^-1.0 Results
[otation D impeller diameter, ft Mc conversion factor, ft'lbM/sec^'lbf N rotational speed. 1/sec n' flow-behavior index, dimensionless P power, ft/^/r/sec apparent viscosity. ^ IbM/ft'Sec P fluid density, /fev/ft^
REYNOLDS NUMBER. 0 ' N / / / ( ,
Power number-Reynolds number correlation for pseudoplasitic fluids.
Chapter 3. Powar draw and consumption
128
Bates, R. L., Fondy, E L. and Corpstein, R. R., Ind. Eng. Chem. Process Des. and Dev., 2,310 (1963) An Examination of Some Geometric Parameters of Impeller Power Experimental apparatus Vessel and impeller geometries Vessel diameters. 6,10,12,15, and 24 inches Turbine diameters. 3,4,5,6,7,8, and 10 inches Turbine styles. Flat six-blade disk style; flat, cun^ed, and 45° pitched six-blade open style; four-blade open styles with blade angles 25 to 90° w/D range. 0.062 to 0.37 Z)/r range. 0.25 to 0.50 fib range. 1 through 12 Wb/T range. 7 to 15% UbUfb/T range. 0.1 to 1 Working fluids and their physical properties water and com syrup (Newtonian fluids) viscosity range 1-120,000 cP Experimental conditions Results 500
Power number-Reynolds number correlation in Newtonianfluidsvarious turbine impeller designs.
3.1 SingI* phase
otat ion impeller diameter D gc fib
N Np NRe
P
T w
Wh
1^ p
gravitational constant number of baffles impeller speed, 1/min power number Reynolds number power tank diameter impeller blade width baffle width viscosity liquid density
229
Chapter 3. Power draw and consumption
130
Beckner, J. L. and Smith, J. M., Trans. Instn. Chem. Engrs., 44, T224 (1966) Anchor-Agitated Systems: Power Input with Newtonian and PseudoPlastic Fluids Experimental apparatus Vessel and impeller geometries Vessel type: flat-bottomed Vessel diameter: 22.9 cm Impeller type:flat-bladedanchor and pitch-bladed anchor
Rotation
••Ub
\^
lin-H
n
± " ] " AA
i
Pitched-bladed anchor. Aims of anchor are pitched at 45^.
t
3.1 Single phase
131 Anchors (flat bladed)
No.
Z)(cm)
h (cm)
width (cm)
C/DT
1 2 3 4 5
21.71 20.44 19.48 18.04 15.65
15.0 15.0 15.0 15.0 15.0
2.50 2.50 2.50 2.50 2.50
0.0264 0.0542 0.0751 0.1067 0.1584
Anchors (pitch bladed) Width (cm) No.
Z>(cm)
h(cm)
Al A2 A3 A4 A5
22.11 20.84 19.33 17.98 16.63
15.0 15.0 15.0 15.0 15.0
Along blade Projected
C/DT
2.38 2.38 2.38 2.38 2.38
3.22 3.22 3.22 3.22 3.22
0.0177 0.0454 0.0784 0.1078 0.1372
Working fluids and their physical properties Newtonian systems Code No. 1 10 4 11 5 2 7
Liquid Lubricating oil (British Petroleum, Llandarcy) Silicone liquid* Dilute golden syrup (Martineau's) Silicone liquid* Silicone liquid* Concentrated golden syrup Silicone liquid*
Viscosity (P)
Density (g/cw?)
6.8'-10.4
0.886
31.0-36.0 49.0-^56.0
0.98 1.364
55.0-61.0 173.0-183.0 385.0-707.0 501.0-618.0
0.98 0.967 1.374 0.967
Non-Newtonian systems Code No. 6 14 15 8 12 9 13
Liquid 10% aqueous CMC** 9.46% aqueous CMC** 7.16% aqueous CMC** 200/100,000 C.S. sihcone* Concentrated PBD*** Polymerised linseed oil Diluted PBD***
0.266-0.338 0.469 0.572-0.611 0.676-0.759 0.702 0.726 0.747-0.766
k (g cm~^ s""^)
Density (g/cnr)
1,763 567 100-115 943-2,293 1,900-2,475 1,117-1,986 934
1.043 L053 1.055 0.967 0.8 0.982 0.804
* Midland Silicones Ltd.: MS 200. ** Carcoxymethyl cellulose. *** Polybutradiene dissolved in ethylbenzene. Dilution was with methyl-cyclohexane. (International Synthetic Rubber Co. Ltd.)
132
Chapter 3. Pow«r draw and consumption
Results P
f c T
N^D^P{DT)
g J N^"D'P ] [* [a (!-«)]"•'J
a = 37-120[|-] Notation a C D DT
k n N P
r
p
T
geometric parameter clearance diameter of impeller diameter of tank constant in T=ky" exponent for power-law fluid rotational speed of impeller power input shear rate density shear stress
3.1 Single ph«s«
133
Bourne. J. R. and Butier, H., Trans. Instn. Chem. Engrs., 47, T263 (1969) Power Consumption of Helical Ribbon Impellers in Viscous Liquids. Experimental apparatus Vessel and agitator geometries Summary of Principal Dimensions Impeller number
dim)
dID
h/D
W/D
S/D
Zo/D
1 2 3 4 5 Nagata^ Rl R2 R3 R3' Gray2 Lightnin^ Hoogendoom and den Hartog"*
10.303 11.030 11.142 11.370 34.34
0.889 0.952 0.962 0.981 0.954
1.06 1.06 1.06 1.06 1.06
0.108 0.108 0.108 0.108 0.104
0.345 0.345 0.345 0.345 0.345
1.22 1.22 1.22 1.22 1.22
3.7 3.7 7.5 11.2 8.5 14 ft
0.94 0.94 0.95 0.95 0.95 —
0.9 0.9 0.95 0.95 0.89 2.2
0.11 0.11 0.10 0.10 0.06 0.09
0.7 1.05 0.95 0.95 0.68 0.56
1.0 1.0 1.0 1.0 1.1 —
9.1
0.96
0.9
0.087
0.58
1.5
1 2 3 4
Nagara, S. et al„ Chem. Eng, Oapan), 1957,21,278 Gray, J. B., Chem. Eng. Progr., 1963,59,55 Viscons Mixing Bulletin B531 Hoogendoom, C. J. et al., Chem. Eng. Sci., 1967,22,1689
Principal dimensions of tank and helical ribbon.
234
Chapter 3. Power draw and consumption
Results
__i£_
n
nil''*'-I)
Notation d D h k K / n N P Po Re p
outside diameter of ribbon inside diameter of tank height of ribbon hid consistency factor in the power law Did exponent in the power law rotational speed of ribbon power consumption dimensionless power number, PIpN ^d ^, dimensionless dimensionless Reynold number, pd W ^"7/iC, dimensionless density of liquid
3.1 Single phase
135
Novlk, V and Rieger, E, Trans. Instn. Chem. Engrs., 47, T335 (1969) Homogenization with Helical Screw Agitators Experimental apparatus Vessel and agitator geometries {Lff-fitf
17
\v
Mt>/O-0.1
Vessel Type Inner diameter (mm) Screw Diameter of screw (nmi) Pitch (mm) Liquid contained Height (mm)
o
„
flat-bottomed
flat-bottomed
100
150
60 60
94 94
100
150
Working fluids and their physical properties Water, glycerol and aqueous solutions of com symp and glycerol Viscosities of those Uquids = 1—10* cP
Results
Resultsfromscrew agitator with draught tube.
Chapter 3. Pow«r draw and consumption
136
10'
W A/'^—REYNOLDS NUMBER
Resultsfromscrew agitator in bafQed vessel.
A ( r , ~ REVNOLOS NUMBER
Resultsfromscrew agitator without baffles.
Notation d outer diameter of helical screw D inside diameter of tank Dt inside diameter of draught tube e offeet of agitator shaft from center of vessel H height of liquid N speed of agitator Np power number, P/pN ^d^, dimensionless P power consumption of agitator s pitch of screw Wb width of baffle fi viscosity of liquid p density of liquid 0 mixing time
3.1 Siiigl«phas«
137
Nagata, S., Nishikawa, M., Tada, H., Hirabayashi, H. and Gotoh, S.J. Chem. Eng. Japan, 3,237 (1970) Power Consumption of Mixing Impellers in Bingham Plastic Liquids Experimental apparatus Vessel Type: (1) (2) (3) flat-bottomed Diameter: (1) 20 (2) 30 (3) 40 cm Impeller Type d/D hID IID pitch
Ribbon 0.95 0.1 0.95 1.0
Anchor 0.5-0.95 0.1 0.5-0.95 —
Turbine 0.5 0.1 0.125 —
Paddle 0.3 -0.95 0.05-0.12 — —
s a) Ribbon
c) Turbine
d) Paddle
Working fluids and solids Dispersoids: CaCOa, MgCOs, kaolin, and Ti02 Dispersion media: city water, glycerin water solutions, machine oil and salad oil Results Np = {PN + KHe')Re-' -^aNy + I Determined coefficients a PN Ribbon 6.13 320 Anchor 4.80 200 6-Blade turbine 3.44 70 6-Blade turbine with baffles 3.44 70
/ 0.2 0.29 — 5.5
K 15 30 10 10
h 1/3 1/3 1/3 1/3
Chapter 3. Power draw and consumption
138
6 fi |03
6 t^r^2
2
A
6 6 ^Q4
10*
Np-Re" correlation forribbonmixer.
50
TOO
500
1000
iV>-/?^"correlation for 6 blade turbine.
5000
3.1 Single phase
Notation b blade width of impeller, cm d diameter of impeller, cm D diameter of mixing vessel, cm h constant, dimensionless He Hedstrom number, Ny{He"fy dimensionless / turbulent power number, dimensionless K proportionality constant / length of anchor arm, height of ribbon, or blade length of impeller, cm n impeller speed, 1/sec Np power number, d ^np/r}, dimensionless Ny yield stress power number, ty/pn^d ^, dimensionless Re" Reynolds number, d ^nplt], dimensionless a proportionality constant, dimensionless PN proportionality constant, dimensionless r] plastic viscosity, g / c m s e c p density, g/cm^ Ty yield stress for Bingham plastic fluids, g/cmsec^
239
Chapter 3. Power draw and consumption
140
Hall, K. R. and Godfrey, J. C, Trans. Instn. Chem. Engrs., 48, T201 (1970) Power Consumption by Helical Ribbon Impellers Experimental apparatus Vessel and impeller geometries Vessel type: flat-bottomed Impeller type: helical ribbon
Diagram of impeller and tank dimensions.
Impellers B (10 inch diam.) and A (IV2 inch diam.).
»c^:22iHr^i*.,
Impellers C, B, and D.
3.1 Single phas«
241
Impeller dimensions Impeller
D
dID
pid
h/d
eld
wid
NR
A B C D E
1.65 11.3 11.3 11.3 22.0
0.898 0.912 0.912 0.902 0.91
0.517 0.495 1.00 1.00 1.0
1.01 0.942 0.996 1.01 1.0
0.0575 0.0485 0.0485 0.0539 0.05
0.135 0.0971 0.0971 0.0981 0.1
1 1 2 1 2
For these impellers H=W2 D. D: inch.
Workingfluidsand their physical properties Newtonian fluids: aqueous solutions of com syrup (viscosities = 60—460 poise) non-Newtonian fluids: a commercial hydroxypropyl methyl cellulose at various concentrations in water
Results Po=^e6Re:\p/dr''^(NR){h/d){w/dfHc/dr'' tion fotaf* clearance between impeUer ribbon and vessel wall c d impeller diameter D diameter of mixing vessel gravitational conversion factor gc impeller height h fluid height H impeller speed, 1/sec N NR number of impeller ribbon pitch of impeller ribbon p p power consumption at impeller shaft {=27tNT) Po power number, Pgc/N^d^p, dimensionless Rea apparent Reynolds number, d^Np/^, dimensionless T torque at impeUer shaft w ribbon width apparent viscosity ^ density P
242
Chapter 3. Pow«r draw and consumption
Foft, L, Vale§ova, H. and Kudraa, V, Collect. Czech. Chem. Commun., 36,164 (1971) Studies on Mixing. XXVII. Liquid Circulation in a System with Axial Mixer and Radial Baffles Experimental apparatus Vessel Type: flat-bottomed Diameter: (1) 190 (2) 290 mm Liquid contained Height: (1)190 (2) 290 mm Baffle Number: 4 Width: 0.1 D Impeller Type: (1) propeller (2) paddle mixer with three inclined blades (3) paddle mixer with six inclined blades Number of impellers: (1)~(3) 1 Number of blades on impeller: (l)'-'(2) 3 (3) 6 D (nmi)
d (mm)
h2 (mm)
Rotational speed of mixer (rpm)
Propeller {s=d) and paddle mixer with three inclined blades (a=24°) 290 290 290 190 190 190
96.6 72.5 58.0 58.0 58.0 58.0
145.0 96.6 72.5 58.0 95.0 58.0
450-^1,000 800-1,800 1,000-2,000 900-1,600 900-1,600 900-1,600
Paddle mixer with six inclined blades (a=45°) 290 290 290 290 190 190 190
96.6 72.5 58.0 46.6 58.0 46.0 46.0
145.0 72.5 72.5 72.5 95.0 58.0 46.0
3 0 0 - 600 600-1,300 900-1,800 1,000-2,000 500-1,000 500-1,000 500-1,000
3.1 Single phas«
143
(a)
(b)
Mixer
(a) Three-blade paddle mixer with inclined blades, a=24*', A=0.2 d. (b) Six-blade paddle mixer with inclined blades, a=45*', /»=0.2 d.
Working fluids and their physical properties
Werking fluids Distilled water Distilled water Aqueous glycerol Aqueous glycerol Aqueous glycerol
r7(cP) 0.5 1.0 3.0 9.2 14.42
P(kg/m') 900 1,000 1,084 1,143 1,161
Results
for i?^> 1.0x10^ Mixer type PropeUer(5=(/) Three-blade paddle (a=24°) Six-blade paddle (a=45°)
B 0.592 0.387 1.014
Notation d mixer diameter, m D vessel diameter, m hz distance of the mixer rotor above the vessel bottom, m Kp pumping capacity, dimensionless n rotational speed of the mixer, 1/sec
f -0.146 0.130 -0.212
np
Re % ri P
0.026 0.060 0.166
number of impeller blades Reynolds number, nd^p/rf, dimensionless volumetric flow rate, mVsec dynamic viscosity of fluid, kg/msec liquid density, kg/m^
Chapter 3. Pow«r draw and consumption
144
Nienow, A. W. and Miles, D., Ind. Eng. Chem. Process. Des. Dev., 10,41 (1971) Impeller Power Numbers in Closed Vessels Experimental apparatus System Vessel Type Diameter (in) Height (in) Baffle Number Width (in)
(1)
(2)
flat-bottomed 6,12 6,12
1flat-bottomed 6,12 6,12
4 0.1 r
4 0.1 r
Impeller Type D/T C/Z DwID DJD x/Dw w/D Number of impellers Number of blades
(a) 1/4-3/4 1/6-3/4 1/5 1/4 0.05-0.44 1 6
(a): six-blade disk turbine (b): four-blade 45** pitched turbine (c): 2-bladeflatpaddle
Working fluid water Experimental conditions Impeller speed System (1): 40-2,400 rpm System (2): 20-1,000 rpm Temperature: 25°C
(b) 1/4-3/4 1/6-3/4 — — 1/4 1 4
(c) 1/4-3/4 1/6-3/4 1/4 — 1 2
3.1 Single phase
145
Results Power numbers for 2 x 10* < Nue < 10^ Identification, run no. r,in.
D/T
Air/water interface
Impeller clearance, C/Z V6(A)
V4(B)
VaCC)
V2(D)
VaCE)
ViiF)
x/D„
3.9 4.9 5.3 5.0 5.3
4.1 5.0 5.6
3.9 4.8 5.0
3.7 4.7 4.6
0.44 0.33 0.22 0.22 0.14 0.10 0.05
6-Blade Disk Turbine 1 2 3 4 5 6 7
6 6 6 6 6 12 12
V4 Va 72 72 V4 74 72
no no no yes no no no
3.6 4.4 4.6 4.2 4.3
3.8 4.7 4.9 4.8 5.0 5.5 5.5
Aerated Aerated Aerated
5.6 5.9 5.8
5.0
4.8
3.0 3.4 3.0 3.3 3.5
2.8 3.2 2.8
2.7 3.0 2.7
1.9 1.6 2.3 1.8 1.7
1.9 1.6 2.1
1.8 1.5 2.0
2-Blade Flat Paddles 8 9 10 11 12
6 6 6 12 12
74 72 V4 74 72
no no no no no
13 14 15 16 17
6 6 6 12 12
74 72
no no no no no
2.7 2.6 2.5
2.8 3.1 2.7 2.8 3.0
2.9 3.3 2.9
4-Blade, 45**-Pitch Turbine
VA
74 72
1.9 1.6 2.3
1.8 1.4 2.2 1.7 1.4
Notation C impeller clearance above the tank bottom, L D hnpeller diameter, L DL length of turbine blade, L Dw width of turbine blade or paddle blade, L N impeller speed, 1/T Np power number, P/pN^D^, dimensionless Nxe Rejmolds number, M) Vv, dimensionless P impeller power, MLVr^ T tank diameter, L w 45°-pitched turbine blade width, L X disk thickness, L Z liquid height, L V fluid kinematic viscosity, L^IT p fluid density, M/D
1.7 1.4 1.9
Chapter 3. Pow«r draw and consumption
146
Nagata, S., Nishikawa, M., Tada, H. and Gotoh, S.J. Chem. Eng. Japan, 4,72 (1971) Power Consumption of Mixing Impellers in Pseudoplastic Liquids Experimental apparatus Vessel Type: (1) (2) (3) flat-bottomed Diameter: (1) 20 (2) 30 (3) 40 cm
Impeller Type d/D b/D IID pitch
Ribbon 0.95 0.1 0.95 1.0
Anchor 0.5-^0.95 0.1 0.5-0.95 —
Turbine 0.5 0.1 0.125 —
Paddle 0.3 --0.95 0.05'-'0.12 —
a c) Turbine
a) Ribbon
d) Paddle
Working fluids and their physical properties Flow properties at high shear rate* Liquid Aqueous CMC LVNO. 1 Aqueous CMC WS-C Aqueous CMC HESS Aqueous PVAl Aqueous PVAc
Weight (%)
m
ik
0.3--6.2 0.5--4.5 1.0- -4.5 10--15 30--35
1.00- '0.270 0.72--0.432 0.668--0.436 0.71--0.57 0.72--0.64
0.01--690 13.1'-22.5 11.4--259 62- '340 7 1 - '220
•Aqueous CMC WS-C and HESS show the power-law behaviorfromthe low shear rate range (8-100 sec"') to the high shearrange(200-1,000 sec"*). However, the othersdod not obey the power-law
3.1 S i n g I * phase
147
Results
iCOO
fo
hv 1
['o
*"^
A-iiiC-.n.:- C^!C .^V'li»t:OtAvjj.JCu> PVAl Sc.ji.if.-n' [ r\'»\
!
IQU;
! i
i
ICC
i
1
Oj
"ojl^ ^'^
.
- I0.1
10
100
iOOO
10000
1X000
iV^-i?g'correlation for pseudoplastic liquids (Ribbon d/D=0.95).
Mite n o l i used K i t i v r 1 n c uf>d s""t' Ncwionians no 3.48% CMC sol. no J o 3.26^; CMC scl. X 2.84%CMC sol. r)f.) no + 2.51% CMC sol. A 2.40% CMC sol. no 1 V 2.51?; CMC sol. no no i 1.83% CMC sol1.67 % C N K : sol no Q no 1 0 1.50 "aCMi: sol. • 1.67% CMC sol. 4 B a ( f l e j . <^l [ • l.50?i:CMCsol. 4B'ltl)f.:.
\e
103
•
r^
50
<
10 ^ ^ t o
^"^ ^
1
10
50
100
i
^
^
^
^o] 500
ILW
iV;>-i?e'correlation for pseudoplastic liquids (6-blades turbine d/D=0.5).
Chaiitttr 3. Pow«r draw and consumption
148 !00
50
CMC
-d/h 1.0%
k
M
0.533 0.667
I
0.833 0.950
0 o
HESS
1.5% 2^%^\
V +
•
•^ 1 X {
o1
10
•^ ^ ^'^
*^p^;^ 0.5
5
10
50
100
Re' ^ d^nf/fd^
iV^-/?« correlation for pseudoplastic liquids (2-blades paddle).
Notation h blade width of impeller, cm d diameter of impeller, cm D diameter of mixing vessel, cm gc gravitational conversion factor, kgm/kgf sec^ k fluid consistency index, dynesec^/cm^ / length of anchor arm, height of ribbon, or blade length of impeller, cm m exponent in power-law rheological equation, dimensionless n impeller speed, 1/sec iVp power number, dimensionless Re Reynolds number, dhipl\i, dimensionless Re* Reynolds number, d^npliXof dimensionless ju viscosity of Newtonian fluid, poise /!« apparent viscosity, poise p density, g/cm^
500
3.1 Single phas«
149
Chavan, V V and Ulbrecht, J., Chem. Eng. /., 3,308 (1972) Power Correlation for Helical Ribbon Impellers in Inelastic NonNewtonian Fluids Use of published data Geometrical variables No.
Reference
rf(cm)
t/d
l/d
w/d
s/d
hid
NR
G.l G.2 G.3 G.4 G.5 G.6 G.7 G,S G.9 G.IO G.ll G.12 G.13 G.14 G.15 G.16 G.17
Bourne and Butler^ Bourne and Butler^ Bourne and Butler^ Gray2 Hall and Godfery^ Hall and Godfery^ Hall and Godfery^ Hall and Godfery^ Hall and Godfery^ Hoogendom and den Hartog^ Johnson^ Nagata et al.^ Nagata et al.^ Nagata et al.^ Reher and Bohm^ Ullrich and Schreiber* Zlokamik®
26.17 28.02 87.22 21.59 4.20 28.70 28.70 28.70 55.88 23.11 10.16 9.40 9.40 19.05 21.00 8.6 18.57
1.12 1.05 1.05 1.05 1.11 1.10 1.10 1.11 1.10 1.04 1.10 1.06 1.06 1.05 1.19 1.08 1.02
1.19 1.11 1.11 0.941 1.01 0.942 0.996 1.01 1.0 0.94 0.966 0.95 0.95 1.00 0.952 1.03 1.00
0.12 0.11 0.11 0.118 0.135 0.0971 0.0971 0.0981 0.1 0.091 0.104 0.12 0.12 0.105 0.114 0.0875 0.099
0.386 0.362 0.362 0.753 0.517 0.495 1.00 1.00 1.00 0.61 0.773 0.74 1.11 1.00 1.28 1.25 0.499
1.37 1.28 1.28 1.15 1.14 1.12 1.12 1.13 1.12 1.56 — 1.06 1.06 1.05 1.19 — 1.02
2 2 2 2 1 1 2 1 2 2 2 2 2 2 2 2 2
1. J. R. Bourne and H. Butler, Trans, Inst. Chenu Engrs, 47 (1969) T263. 2. J. B. Gray, Chem, Eng. Progr,, 59 (1963) 55. 3. K. R. HaU and J. C. Godfrey, Trans. Inst. Chem. Entrs, 48 (1970) T201. 4. C. J. Hoogendom and A. P. den Hartog, Chem. Eng. Sci., 22 (1967) 1689. 5. R. T. Johnson,Ind. Eng. Chem., 6 (1967) 340. 6. S. Nagata, M. Yanagimoto and T. Yokoyama, Mem. Fac. Eng. Kyoto University, 18 (1956) 444. 7. E. Reher and R. Bohm, Chem. Technik., 3 (1970) 136. 8. H. Ullrich and H. Schreiber, Chemie-Ingr.-Techn., 39 (1967) 516. 9. M. Zlokamik, Chemie-Ingr.-Techn., 39 (1967) 539.
Results PO =
E\
d
4n nW^'-l)
^Re'
where Re = d^N^-""p / k and £ = 2.49 de d
2 (w/d)
t d •
^
\t/d)-[1-2 (u>/d)]\ (t/d)-l
150
Chapter 3. Power draw and consumption
Notation a Ald^ surface area of the ribbon impeller A impeller diameter d de
E h k I n N NR
P Po Re s t w X P
equivalent diameter constant height of the hquid colunm consistency index in the power law equation impeller length flow behavior index in the power law equation rotational speed of the impeller number of impeller ribbons power consumption power number, P/d^N^p Reynolds number, d^N^~*^p/k impeller pitch vessel diameter impeller width t/de density
3.1 Single phas*
151
Chavan, V V and Ulbrecht, J., Ind. Eng. Chem. Process Des. Dev., 12,472 (1973) Power Correlation for Close-Clearance Helical Impellers in NonNewtonian Liquids Use of published data Impeller type Helical screw impellers with draught tube Helical ribbon impellers Combined ribbon-screw impellers Geometrical variables for the impellers
Helical screw impeller with a draught tube.
i
1
I
J
1
\
'1
i
IS T
A single-bladed helicalribbonimpeller and combinedribbon-screwimpeller.
Chapter 3. Pow«r draw and consumption
152
Geometrical Variables for Helical Screw Impellers with Draught Tube
No.
diem)
t/d
h/d
l/d
s/d
w/d
c/d
dr/d
Irld
Crid
G.l G.2 G.3 G.4 G.5 G.6 G.7
30.5 20.35 20.35 20.35 19.05 14.00 12.70
1.50 2.25 2.25 2.25 2.40 3.28 3.60
1.94 2.70 2.70 2.70 3.10 4.24 4.65
1.50 2.25 2.25 2.25 2.40 3.24 2.%
0.96 0.50 1.00 1.00 0.80 0.93 0.79
0.42 0.39 0.39 0.39 0.42 0.39 0.38
0.104 0.156 0.156 0.156 0.167 0.228 0.250
1.16 1.05 1.05 1.74 1.12 1.53 1.14
1.83 2.54 2.54 2.54 2.93 4.01 4.40
0.104 0.156 0.156 0.156 0.167 0.228 0.250
Geometrical Variables from Literature for Helical Screw Impellers with Draught Tube
No.
Ref.
G.l G.2 G.3 G.4 G.5 G.6 G.7 G8 G.9
Chavan,e/fl/.(1972) Chavan.«/a/.(1972) Chavan,^fl/.(1972) Chavan,«/a/.(1972) Chavan,g/fl/.(1972) Chavan,€^a/.(1972) Nagata,«/a/.(1957) Nagata,«/a/.(1957) Nagata,«/a/.(1957)
No.
Ref.
rf(cm)
t/d
h/d
l/d
s/d
w/d
c/d
dr/d
Ud
cjd
20.35 2035 19.05 2035 20.35 19.05 4.50 6.50 6.28
2.25 2.25 2.40 1.50 1.50 1.60 2.22 1.54 1.59
2.63 2.63 2.80 1.75 1.75 1.83 2.22 1.54 1.59
2.31 2.31 2.47 1.56 1.56 1.67 2.0 1.30 1.42
0.5 1.0 0.8 0.5 1.0 0.8 0.67 1.38 0.72
0.39 0.39 0.42 0.39 0.39 0.42
0.31 0.31 0.33 0.19 0.19 0.20 0.11 0.07 0.075
1.13 1.13 1.2 1.03 1.13 1.2 1.15 1.11 1.08
2.25 2.25 2.4 1.50 1.50 1.60 1.55 1.23 1.26
0.19 0.19 0.2 0.13 0.13 0.14 0.25 0.16 0.16
Geometrical Variables from Literature for Helical Ribbon Impellers
G.l G.2 G.3 G.4 G.5 G.6 G.7 G8 G.9 G.IO Gil G.12 G.13 G.14 G.15 G.16
d{cm)
Nagata,£/a/.(1972) Nagata,e^fl/.(1972) Nagata,€^
19 19 19 19 19 19 19 19 6 6 6 9.6
h/d
t/d 1.05 1.05 1.05 1.068 1.068 1.068 1.05 1.079 1.105 1.158 1.579 1.08 1.05 1.05 1.02 1.05
1 1 1
1.8 1.25 1.25 1.25
l/d
s/d
w/d
NR
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 •1.0 1.0 1.0 1.2 0.98 0.98 0.98 1.0
1 1 0.5 0.75 1.0 1.25 1.25 1.25 1.25 1.25 1.25 1.24 0.39 0.62 1.05 1.0
0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.09 0.1 0.1 0.1 0.1
2 1 1 2 2 2 2 2 2 2 2 1 2 2 2 2
Geometrical Variables for for a Combined Ribbon-Screw Impeller
No. G.l G.2 G.3 G.4 G.5 G.6 G.7
Ref. This woric Nagata,e^a/.(1972) Nagata,e^a/.(1972) Nagata,efa/.(1972) Nagata,efa/.(1972) Nagata,efa/.(1972) Burgbacher (1969)
di (cm)
t/dx
h/di
l/di
s\/d\
w\/di
dz/dz
wz/dz
sz/di
NR
^15
1.03 1.05 1.05 1.05 1.05 1.05 1.05
1.30 1.05 1.05 1.05 1.05 1.05 0.76
1.15 1.0 1.0 1.0 1.0 1.0 0.36
0.57 1.0 1.0 1.0 1.0 0.5 0.72
0.12 0.1 0.1 0.1 0.1 0.1 0.14
0.286 0.42 0.42 0.525 0.525 0.35 0.72
0.4
1.0 2 2 1.5 1 1.5 0.72
1 2 1 2 2 1 1
033
3.1
153
References Butgbacher, G., University of Stuttgart, Department of Mechanical Process Techniques, Study No. 27 (1969) Chavan, V. V., Ulbrecht, J., Chenu Eng. /., 3,308 (1972) Nagata, S., Yanagimoto, T., Yokoyama, T., Kagaku Kogaku, 21278 (1957) Nagata, S., Nishikawa, M., Tada, H., Hirabayashi, H., Gotoh, S.,/. Chem, Eng. Japan, 3,237 (1970) Nagata, S., Nishikawa, M., Katsube, T., Takaishi, K., Int. Chem, Eng., 12,172 (1972) Kappel, M., Seibring, H., Verfahrenstechnik, 4,470 (1970) MuUer, W., DECHEMA (J)eut. Thes. Chem, Apparatewesen)M(mogr., 66,247 (1971) Novak, v., C. Sc. Theses, Distributed by Statni Technicka Knihovna CSR, Narodni Knihovna, Praha 1, Klementinum, Czechoslovakia, 1970
Results For inehstic shear-thinning liquids agitated by the screws with a draught tube PoRe = 2.bna
r^i,.
4n
nir'-l) where
^ = l--2(w/d) a a
._
Ut/d)-l-2(iv/d)\
""l
it/d)-l
I
For ribbon and combined ribbon-screw impellers /
\ (
^«/
\0^7/
\-0.046/
x-0.036
Notation a c Cr Cr
d de dr
h k I Ir n N NR
p Po Re s t w p k
dimensionless surface area clearance between the impeller and the bottom of the vessel clearance between the draught tube and the bottom of the vessel clearance between the draught tube and the top of the vessel impeller diameter equivalent diameter draught tube diameter height of the liquid column consistency index in power law length of the impeller flight length of the draught tube flow index rotational speed of the impeller number of ribbons power consumed power number, P/pN^d^ Reynolds number, d^N^~**p/k pitch of the impeller vessel diameter width of the impeller blade density parameter in power corrections viscosity
Chapter 3. Power draw and consumption
154
Rieger, E and Nov^, V, Trans. Instn, Chem. Engrs., 51,105 (1973) Power Consumption of Agitators in HigWy Viscous Non-Newtonian Liquids. Experimental apparatus Vessel and impeller geometries Helical screw agitators
1
11 —3^^
(a)
System
(b)
^
>i
^^1
* MI
(0
(d)
Screw agitator with a draught tube Figure (a)
Screw agitator in the off-centered position Figure (b)
60 and 94 1.0 0.61 1.1
60 and 94 1.0 0.61
d(mm) s/d d/D Dt/d c/D
0.02
Helical ribbons System
Figure (c)
rf(mm) s/d d/D w/d
96 and 141 1.0 0.95 0.1
Anchor-type agitators System
Anchor Figure (d)
Pitched blade anchor Figure (e)
^(mm) w/d d/D hr/d
90 and 133 0.133 0.9 0.89
133 0.89 0.9 0.89
(e)
3.1 SingI* phas*
255
Workingfluidsand their physical properties aqueous solutions of CMC aqueous solution of polyacrylamide mixtures of CMC solutions with com syrup and starch solutions n=0.31-^0.97 if=0.5-60 kg/mCsec)"-^
Results "hr/d P(> = 0.7;r^fi^^
Notation c d D
UJ
{D/df
ReT [(Z)/rf)'^''-0.75r
clearance between the agitator and vessel wall agitator diameter vessel diameter draught tube diameter Dt agitator length hr height of hquid level in the vessel H coefficient in equation ya=kN k consistency index K flow behaviour index n speed of impeller N power P Po power number Ren Reynolds number, Nd^p/KikN)*"-' pitch of the agitator s width of the agitator blade w shear rate y
Chapter 3. Pow«r draw and ccmsumption
156
Chavan, V V and Ulbrecht, J., Trans. Instn, Chem. Engrs., 51,349 (1973) Power Correlation for Off-Centered Helical Screw Impellers in Highly Viscous Newtonian and Non-Newtonian Liquids Experimental apparatus Vessel and impeller geometries Vessel type: flat-bottomed Vessel diameter: 45.6 cm
Off-centered helical screw impeller Geometrical variables for helical screw impellers with draught tube
No.
diem)
t/d
h/d
l/d
s/d
w/d
eld
eld
G.1.1
29.2 20.35 20.35 29.2 20.35 20.35 20.35 20.35
1.56 2.25 2.25 1.56 2.25 2.25 2.25 2.25
2.02 2.70 2.70 2.02 2.70 2.70 2.70 2.70
1.62 2.25 2.25 1.62 2.25 2.25 2.25 2.25
0.54 0.5 1.0 0.54 0.5 0.5 1.0 1.0
0.45 0.39 039 0.45 039 039 039 039
0.109 0.156 0.156 0.109 0.156 0.156 0.156 0.156
0 0 0 0.173 0.25 0.50 0.25 0.50
Q.\2 G.1.3 G.1.4 G.1.5 G.1.6 G.1.7 G.1.8
Working fluids Aqueous solutions of com symp, Natrosol, CMC and PAA
3.1 SingI* phas«
157
Results Po («-i)
1.9 1+
Notation a c d e h k I n N P Po Re' s t w p
dimensionless surface area of the impeller clearance between the impeller and the bottom of the vessel diameter of the impeller offset of the centre of the impeller from the center of the vessel height of the liquid column consistency index in power law liquids length of the impeller flow behaviour index in power law model rotational speed of the impeller power consumed power number, P/pN^d^^ dimensionless Reynolds number, d W^'^p/^* dimensionless impeller pitch vessel diameter width of the impeller blade density
Chapter 3. Pow«r draw and consumption
158
Sawinsky, J., Havas. G. and De^, A., Chem. Eng. Sci., 31,507 (1976) Power Requirement of Anchor and Helical Ribbon Impellers for the Case of Agitating Newtonian and Pseudo-plastic Liquids Experimental apparatus Vessel and impeller geometries The values of the coefficients and the exponent of equation (1) Anchor impeller
Helical-ribbon impeller
0.5 ~ 0.98 0.5 - 1.5 0.07 - 0.16 <30 17 0.45 2/ + (/
0.84 - 0.% 0.8 ~ 2.36 0.084 - 0.12 0.36 - 1.28 <100 19 0.45 Z'Ki^idnlsf
d/D lid bid sId Re C a L
The values of the coefficients of equations (2) and (3) Anchor impeller 0.8 --0.95 0.9 --1.1 0.1 --0.13
dID lid bid sId m j B
0.3 - 0.8 1.4 7,6 dID-33
0.8 -1.0 1.0 7.6/Z)-5
esults N
^A.dW'K
^ -KTI
(1)
Am =j''A
(2)
^
(3)
=exp[(m-l)-5]
T =/ry'"
Helical-ribbon impeller 0.84 ~ 0.96 0.8 ~ 1.1 0.084 ~ 0.12 0.36 ~ 1.28 0.3 -1.0 1.0 4.2(i/Z)-0.5
3.1 Siiigl«plMis«
Notation a constant b width of impeller blade, m C coefficient d diameter of impeller, m D diameter of vessel, m e clearance between vessel wall and impeller edge, m constant i K consistence factor I height of impeller, m L length of impeller edge, m m viscosity index n speed of agitator, 1/sec N power consumption of impeller, kgmVsec^ Re Reynolds number, d^np/fi, dimensionless pitch of helical ribbon, m s number of impeUer ribbons z f shear rate, 1/sec ^ viscosity, kg/msec P density, kg/m^ T shearing stress, kg/msec^
259
IQQ
Chapter 3.
Pow«r d r a w and consumption
Matsumura, M., Masunaga, H., Haraya, K. and Kobayashi, J.,/. Ferment. TechnoL, 56,128(1978) Effect of Gas Entrainment on the Power Requirement and Gas Holdup in an Aerated Stirred Tank Experimental apparatus Vessel Type: flat-bottomed Diameter: 218 mm Liquid contained Height: 218 mm Baffle Number: 3 Width: 25 mm Impeller Type: six-blade turbine Diameter: 0.487 Dr Number of impeUers: 1 Number of blades on impeller: 6 Off-bottom clearance: DT/3 Working fluids and their physical properties Liquid: water, ethyl alcohol, benzyl alcohol, ethylene glycol, and sucrose solution viscosity: 0.8—30 cp surface tension: 22—71 dynes/cm densities: 0.8-1.3 g/ao? Results Nfr ^ 0.45 NFr > 0.45
Npo = 5.3 Npo = 3.80 M^v^-^
Notation Di impeller diameter, m DT tank diameter, m g gravitational acceleration, m/sec^ N rotational speed of impeller, 1/sec NF^ Froude number, N'^Dilg, dimensionless Npo power number in ungassed liquid, PogdpN^D?, dimensionless Po power consumed in agitation of ungassed liquid, kgm/sec p density of liquid, kg/m^
3.1 Single phase
161
Patterson, W. L, Carreau, R J. and Yap, C. Y.^AIChE Journal, 25,508 (1979) Mixing with Helical Ribbon Agitators. Part II Newtonian Fluids Experimental apparatus Vessel and impeller geometries Vessel type: flat-bottomed Impeller type: helical ribbon
Sketch of helicalribbonagitator system. Impeller characteristics Geometry Impeller
A B C D E F G H
I
n m IV V VI
vm VI
d
D
h
ds
(mm)
(mm)
(mm)
(mm)
fib
Did
lid
wid
Pid
0.130 0.130 0.130 0.105 0.130 0.222 0.219 0.222
0.145 0.145 0.145 0.145 0.145 0.248 0.248 0.291
0.137 0.137 0.137 0.137 0.137 0.234 0.238 0.234
6.35 6.35
2 2 2 2 1 2 2 2
1.11 1.11 1.11 1.37 1.11 1.11 1.12 1.30
4.48 3.00 4.12 4.00 4.39 4.44 4.75 4.44
0.097 0.097 0.195 0.121 0.097 0.099 0.072 0.099
0.719 1.048 0.707 0.848 0.695 0.690 0.724 0.690
635 6.35 6.35 9.53 9.53 9.53
Chapter 3. Power draw and consumption
162
Working fluids and their physical properties Fluid 100% glycerol 100% glycerol 100% glycerol Silicone oil Vitrea oil
P(kg/m^)
A/(Ns/m2)
1,254 1,254 1,259 1,100 869
0.568 0.708 0.800 0.137 0.193
Results siny + 1.8cosy] '^'
"d'Np
(1)
{jm
This equation can be simplified on the following grounds: 1. For commonly used helical ribbon agitators, w/d = 0.1, and yf=^ 15 deg. Therefore, we set (u;/(/)0i6 ~ 0.69, sin v^= 0.258, and cos y/^ 0.965. 2. Within the range of the experimental conditions, ReS'^ varies from 1.52 to 2.17. Hence, we take Re^^ = 1.82 as an average value. Equation (1) then reduces to
m
Na93
Np=24nt
d'Np
(2)
Notation d diameter of impeller, m ds diameter of impeller shaft, mm D diameter of vessel, m h height of impeller, m H height of liquid in vessel, m / length of impeller blade, m fib number of blades N rotational speed of impeller, 1/sec Np power number, P/pN ^d ^, dimensionless p impeller pitch P power consumed, W Re Reynolds number for mixing systems, d ^Nplji, dimensionless w blade width, m /x fluid viscosity, Nsec/m^ p fluid density, kg/m^ \lf blade inclination angle, degree
3.1 SingI* phas*
163
Yap, C. Y, Patterson, W. I. and Carreau, R J., AIChE Journal, 25,516 (1979) Mixing with Helical Ribbon Agitators Part III Non-Newtonian Fluids Experimental apparatus Vessel and impeller geometries Vessel type: flat-bottomed Impeller type: helical ribbon
Sketch of helical ribbon agitator system. Impeller characteristics Geometry Impeller A B C D E F G H
I
n m IV V VI
vm VI
d (mm)
D (mm)
h (mm)
(mm)
ftb
D/d
l/d
w/d
p/d
0.130 0.130 0.130 0.105 0.130 0.222 0.219 0.222
0.145 0.145 0.145 0.145 0.145 0.248 0.248 0.291
0.137 0.137 0.137 0.137 0.137 0.234 0.238 0.234
6.35 6.35 6.35 6.35 6.35 9.53 9.53 9.53
2 2 2 2 1 2 2 2
1.11 1.11 1.11 1.37 1.11 1.11 1.12 1.30
4.48 3.00 4.12 4.00 4.39 4.44 4.75 4.44
0.097 0.097 0.195 0.121 0.097 0.099 0.072 0.099
0.719 1.048 0.707 0.848 0.695 0.690 0.724 0.690
ds
254
Chapter 3. Pow«r draw and consumption
Working fluids and their physical properties Fluid 100% glycerol 100% glycerol Vitrea oil 1.0% Natrosol 250-HR 1.5% Natrosol 1.5% CMC-7H 2.0%CMC-7H 0.8%SeparanAP-30 1.0%SeparanAP-30 1.5% Separan** AP-30
P(kg/m3) 1,254 1,249
869 1,000 1,000 1,000 1,000 1,000 1,000 1,000
^ (Ns/m^) 0.568 0.800 0.193 1.07 24.0
2.5 10.0
340 1,100 1,200
S ~ — 0.235 0.381 0.175 0.244 0.382 0.392 0.417
^i(s)
A*(s)
~ —
— — — -
0.233 1.30 0.437 1.26 99.3
298 145
0.12 0.052 0.59 0.70 0.60
*The characteristic elastic time constant was calculated from Theological data at a shear rate equal to 10 s~* through the relation ^ = TU - Tzz/tn y. **Aged polymer powder. Results -1
Notation d ds D h H / Hb N Np p P Reg 5 ^1 w 7 r]e /x p Ti2 Til - T22
diameter of impeller, m diameter of impeller shaft, mm diameter of vessel, m height of impeller, m height of liquid in vessel, m length of impeller blade, m n u m b e r of blades rotational speed of impeller, 1/sec power number, P/pN^d^, dimensionless impeller pitch p o w e r consumed, W generahzed Reynolds number, d Wp/n^, dimensionless fluid rheologicd parameter, dimensionless fluid characteristic time, sec blade width, m shear rate, 1/sec effective viscosity, Nsec/m^ fluid viscosity,Nsec/m^ fluid density, kg/m? shear stress, N/m^ primary normal stress difference, N/m^
3.1 Singl«plMis«
165
Blasinski, H. and Rzyski, E., Chem. Eng. /., 19,157 (1980) Power Requirements of Helical Ribbon Mixers Use of published data Vessel and impeller geometries Vessel type: flat-bottomed Impeller type: helical ribbon
Xl 1/
-b
1^
1
I
1
Schema of the helicalribbonmixer.
J.
\
^ 1
f
0
Ref.
K
eld
Hid
pid
hid
hid
1 1 2 3 3 3 4 4 6 7 S 9 10 11 12 13 2 2 2 5 5 5 5 5 5 5 5
130 130 250 300 416 257 336 248 420 235 590 310 237 1,000 760 296 230 130 207 215 210 205 218 198 234 194 174
0.095 0.055 0.048 0.03 0.01 0.05 0.026 0.032 0.029 0.036 0.021 0.052 0.0375 0.01 0.026 0.026 0.057 0.054 0.048 0.017 0.035 0.055 0.035 0.035 0.035 0.035 0.035
1.19 1.11 1.12 1.06 1.02 1.10 1.052 1.064 1.412 1.072 1.008 1.103 1.64 1.02 1.28 1.158 1.136 1.13 1.12 1.034 1.071 1.111 1.071 1.071 1.071 1.071 1.071
1.28 1.1
1 1 0.996 1 1 1 1 0.96 0.941 1.036 0.915 0.966 1.03 1 1.11 1 1.01 1.01 0.942 0.862 0.893 0.926 0.893 0.893 0.893 0.893 0.893
0.114 0.103 0.0971 0.1 0.1 0.1 0.105 0.117 0.118 0.167 0.0905 0.1035 0.0875 0.1 0.11 0.1 0.135 0.0981 0.0971 0.103 0.107 0.111 0.142 0.071 0.107 0.107 0.107
0.745 0.753 0.57 0.61 0.772 1.25 0.5 0.362 1 0.517 1 0.495 0.431 0.446 0.446 0.446 0.446 0.357 0.596 0.892
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
IQQ
Chapter 3. Pow«r draw and consumption
Results For i?^ < 100
4 = 0.01 ~ 0.095, ^ = 1.02 ~ 1.64, 4 = 0-357 ~ 1.28, a d d - = 0.862--1.11, - = 0.071-0.167, « = lor2 d d X-O^/
\0.45/
\-0.63/r
\1.01/
\0.14
Poi?^ = 3 4 . l |eReferences 1. E. 0. Reher and R.B6hm, Chem. Tech., 22 (1970) 230. 2. K. R. HaU and J. C. Godfrey, Trans. Inst. Chem., 48 (1970) 201. 3. A. Mersmann, W. D. Einenkal and M. KSppel, Chem. Ing. Tech., 47 (1975) 953. 4. S. Nagata, Mixing, Kodansha, Tokyo, and Wiley, New York, 1975. 5. H. Blasiiiski, and Cz. Kuncewicz,Inz. Chem., 8 (1978) 807. 6. J. B. Gray, Chem. Eng. Prog., 59 (1963) 55. 7. M. D. Gluz and I. S. Pavlushenko, Zh. Pnkl Khim., 40 (1967) 1485. 8. C. J. Hoogedoom and A. P. den Hartog, Chem. Eng. Sci, 22 (1967) 1689. 9. R. T. Jounson, Ind. Eng. Chem. Proc. Des. Dev., 6 (1967) 340. 10. H. Ullrich and H. Schreiber, Chem. Ing. Tech., 39 (1967) 218. 11. M. Zlokamik, Chem. Ing. Tech., 39 (1%7) 539. 12. J. R. Bourne and H. Butler, Trans. Inst. Chem. Eng., 47 (1969) 263. 1.3 V. Nov^ and F. Rieger, Chem. Eng. J., 9 (1975) 63. Notation b width of ribbon blade, m D tank diameter, m d impeller diameter, m e clearance between impeller and tank wall, m H height of liquid level above tank bottom, m h height of impeller, m i number of helixes in impeller K Po Re, dimensionless N rotational velocity of impeller, 1/sec P mixing power input, W Po power number, P/N ^d ^p, dimensionless p pitch of heUcal impeller, m Re Reynolds number, Nd ^pl ry, dimensionless 77 viscosity of liquid, Pasec p density, kg/m^
3.1 Single phas«
167
Bertrand, J. Couderc, J. R and Angelino, H., Chem. Eng. Sci, 35,2157 (1980) Power Consumption, Pumping Capacity and Turbulence Intensity in Baffled Stirred Tanks; Comparison Between Several Turbines Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.40 m Liquid contained Height: 0.40 m Volume of liquid in vessel: 50.3 £ Baffle Number: 4 Width: 0.04 m Impeller Type System 1 Si System 2 S2 System 3 S3 System 4,5 S4, S5 System 6 Se Geometries
sixflatblade disk turbine (Figure 1) sixflatblade disk turbine (Figure 1) an impeller shown in Figure 2 an impeller shown in Figure 2 an impeller shown in Figure 3
H-T«400mm h«-|-«2CX)rrwn w«'jt«40mm
C^'-j-O'lOOmm !„•-*-•27 mm
L«-?-»33mm
Figure 1
Chapter 3. Pow«r draw and consumption
168
•4^S
S j system
S)^ system
S,ond £^ systems
^133 Figure 2
Off-bottom clearance: Si
S2
S3
S4
Ss
r/2
0.37
r/2
r/2
r/2
Working fluid water Experimental conditions and results Systems
5^"^^,^^ number u. Reynolds
S,
S,
14,700-67,800 *'»»'w u«,c»w 14,700-67,800
Power number NP Non-dimensional pumping coefficient NQ
5.1 - ^Q
14.700-67,800
14.700-67,800
10,100-46,400
4.9
4.2
3.4
9.2
1.61
1.11
0.65
131
Notation D Dc h H Ip Ig N Np NQ
agitator diameter, m agitator disk diameter, m agitator level in the tank, m water level in the tank, m width of the blades, m height of the blades, m agitator rotational speed, 1/sec power number, P/p7^^^Z)^ dimensionless pumping coefficient, Q/ND^^ dimensionless
P Q
Re T w A^ P
e
power input, kgmVsec^ piunping capacity, mVsec Reynolds number, ND^p/fi, dimensionless tank diameter, m baffle width, m viscosity, kg/msec density, kg/w? flow angle, degree
3.1 SingI* phas«
169
Takahashi, K., Aral, K. and Saito, S.J. Chem. Eng. Japan, 13,147 (1980) Power Correlation for Anchor and Helical Ribbon Impellers in Highly Viscous Liquids Experimental apparatus Vessel Type: flat-bottomed Diameter: 12.80 cm Height: 12.80 cm
Impeller Type Diameter (cm) Height (cm)
helical ribbon 10.28-12.00 12.50 0.102 0.094
anchor 11.52-12.67 11.50 0.102 0.094
w/D dJD
^
g4
^
w
1 1 J
!
1 1 LJ
d D
^
•i
1 1
L»h/sineB
Geometrical configurations of anchor and helicalribbonimpellers.
Cjeometrical variables of anchor and helical ribbon impellers
Geometry Anchor impellers
HeUcal ribbon impellers
No. ACl AC2 AC3 AC4 AC5 DHl DH2 DH3 DH4 DH5
d
c/D
11.52 12.16 12.48 12.54 12.67
0.0500 0.0250 0.0125 0.0100 0.0050
12.00 11.24 10.28 11.29 11.38
0.031 0.061 0.098 0.059 0.055
D/s
L
1.02 1.02 1.02 1.54 2.05
39.72 37.46 34.63 54.65 72.59
270
Chapter 3. Power draw and consumption
Workingfluidsand their physical properties Aqueous solutions of com syrup viscosities: lO-^-SOO poise Results For anchor impellers NpRe^
}^^I^ k.f{D/c) 21n{4 + 8c/f(;)-l d ^
where /(Z)/c) = l+0.00735(Z)/c)°-*^ For anchor and helical ribbon impellers 2hi(4+8c/M;)-l d where sin^fl=s/-J(;r(/)^ + 5^ Notation c clearance between impeller and vessel wall, cm d impeller diameter, cm ds shaft diameter, cm D vessel diameter, cm gr gravitational constant, gcm/Gsec^ height of blade, cm h H height of vessel, cm L length of blade, h/sin GB, cm Hp number of blades N rotational speed of the impeller, 1/sec Np power number, PgclpN^d^, dimensionless P power consumption, Gem/sec Re Reynolds number, d^Np/^f dimensionless s impeller pitch, cm w blade width, cm GB blade angle, rad jix viscosity, g/cmsec p density, g/cm^
3.1 Singl« phas»
271
Gray, D. J., Treybal, R. E. and Baraett, S. M., AIChE Journal, 28,195 (1982) Mixing of Single and Two Phase Systems: Power Consumption of Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.0287 m Baffle Number: 4 Width: 0.287 m Impeller Type: sixflat-bladedisc turbine Diameter: 0.0906 Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: C/D=^ 0.5,1.167 and 1.5 Working fluid Water Results 7V^ = 5.17(C/Z))°-2^
for
C/D
Np=^ 5.17
for C/Z)> 1.1
Notation C impeller height off the tank bottom, m D impeller diameter, m gc gravitational constant, kgm/kgf sec^ Po mechanical agitation power in ungassed Uquid, W N impeller rotational speed, 1/sec Np power number, Pagc/pN^D^, dimensionless p liquid density, kg/m^
Chapter 3. Pow«r draw and consumption
172
Takase, H., Unno, H. and Akehata, T, Kagaku Kogaku Ronbunshu, 8,560 (1982) Power Consumption of Surface Aerator in a Square Tank Experimental apparatus Vessel and impeller geometries System
(1)
Vessel Type Length and width (m) Water depth (m) Impeller Type Diameter of disk (m) di
(3)
flat-bottomed square tank 0.2 0.075-0.2
0.3 0.075-0.3
0.5 0.075-0.5
disk with six blades underneath the disk 0.03,0.06
0.03,0.06,0.12
0.06,0.12
20:7:2
ilbiWd
Number of impellers Number of bladed Off-top clearance (m)
(2)
1 6 0,0.01,0.02
1 6 0,0.01,0.02
0.03 5.00-41.7
0.06 1.67-16.7
0.03 5.00-41.7
0.06 1.67-16.7
0.12 0.83-6.67
0.06 1.67-16.7
0.12 0.83-6.67
1 6 0,0.01,0.02
Working fluid Tap water Experimental conditions System (1) di(m) Impeller speed (rps) System (2) di(m)
Impeller speed (rps) System (3) di(m)
Impeller speed (rps)
3.1
173
Results Below the critical Reynolds number H/W<03S Np=32 H/W
H]
xr
-
Npr^lO
,^-0.77|lo«io(*7IK)+a7f~
^0.3S AT
AT
,^-0.77|logio(rf.7iy)+0.7f^
Above the critical Reynolds number H/W^03S Np = 0.88
(Re/Recr''\di/Wy''''
H/W<03S Np = 0.17
(Re/Recr'\di/Wy'\H/Wf'
Notation di gr H Hso lb n Np Npnax P Re RBC Wb W /x p
impeller diameter, m gravitational conversion, kgm/kgfsec^ water depth, m initial impeller submergence, m blade length, m rotational speed of impeller, 1 / sec power number, Pgc/p « W , dimensionless maximum value of iVp power, kgfm/sec Reynolds number, pndiVi^, dimensionless Reynolds number at Hso=0 blade width, m tank width, m viscosity of water, kg/msec density of water, kg/m^
Chapter 3. Power draw and consumption
174
Sano, Y. and Usui, H.,/. Chem. Eng. Japan, 18,47 (1985) Interrelations among Mixing Time, Power Number and Discharge Flow Rate Number in Baffled Mixing Vessels Experimental apparatus Vessel Type: (1) (2) flat-bottomed Diameter: (1)0.2 (2) 0.4 m Liquid contained Height: (1)0.2 (2) 0.4 m Baffle Number: (1) (2) 4 Width: (1)0.02 (2) 0.04 m Impeller Type d/D b/D tip
paddle 0.3,0.4,0.5,0.6,0.7 0.05,0.10.0.15,0.20,0.30 2,4,6
turbine 0.4,0.5,0.6,0.7 0.1,0.15,0.2,0.3,0.4 2,4,6,8
t
Ibd (a: c: b = 5: 2:20) Turbine
Paddle
Working fluid Tap water Experimental conditions 0.3 < d/D < 0.7 0.05 < b/D < 0.3 25x 10^ Results For paddles Np=73(d/Dr For turbines
Hb/DtW
Np=3.6{d/D)- Hb/Df^np" Notation a impeller length, m b impeller width, m c length of impeller disk inserted into blade, m d impeller diameter, m D vessel diameter, m n impeller rotational speed, 1/sec
Np
P Re
number of impeller blades power number, P/pvPd^y dimensionless mixing power consumption, W impeller Reynolds number, d^n/v, dimensionless kinematic viscosity of liquid, mVsec Uquid density, kg/m^
3.1 SingI* plias»
175
Bertrand, J. and Couderc, J. R, Chem. Eng. Res. Des., 63,259 (1985) Evaluation of the Power Consumption in Agitation of Viscous Newtonian or Pseudoplastic Liquids by Two-bladed, Anchor or Gate Agitators Experimental apparatus Vessel Type: flat-bottomed Height: T Volume: 200 £ Agitator geometries Agitator Two-bladed impeller
Anchor
Gate-agitator
Geometries studied Dimensions (I>A/T H/T
D/T 0.336 *0.508 0.656 0.828 D/T 0.730 *0.779 0.828 0.926 D/T 0.631 *0.656 0.730 0.828
0.0417
1 W/T
H/T
A/T
0.0417 il>A/T
1
0.0737
H/T
DYO/T
0.0417
0.165 0.189 0.263 0.361
1
Dvo/T 0.312 0.337 0.410 0.509
^Experimentally studied. D 1
1
th_|
W\I—^ 1 H
1 g
1
^ 1 Jawi 1 T
Two-bladed impeller
Anchor
J
Gate-agitator
DY/T
0.484 0.509 0.582 0.681
276
Chaptor 3. Power draw and consumption
Working fluids Newtonianfluid:a viscous oil Pseudoplasticfluid:a carbopol solution Results Newtonian fluid (1) Two-bladed impeller 0.08 I NpRe increases with Re (2) Anchor 0.26 0.7 for a Carreau fluid Re < 0.4 and 0.4 < « < 1 NpRe = 175 (73r-' (2) Anchor for a Carreau fluid NpRe = 149 (16)"-^ (3) Gate-agitator for an Ostwald de Waele fluid NpRe = 169 (12 jy-' Notation D agitator diameter, m m consistency index, kg/m(sec)"~^ n flow behaviour index N rotational speed, 1/sec Np power number, P/pN^D^, dimensionless P power consumption, kgmVsec^ Re Reynolds number, dimensionless for Newtonianfluids,pNDVr] for Ostwald de Waelefluids,pN'^^'D'^lm for Carreaufluids,pNDVr]o T tank diameter, m T] viscosity, kg/msec rjo viscosity, kg/msec p fluid density, kg/m^
3.1 SingI* phas«
177
Shamlou, R A. and Edwards, M. E, Chem. Eng. Set., 40,1773 (1985) Power Consumption of Helical Ribbon Mixers in Viscous Newtonian and Non-Newtonian Fluids Experimental apparatus Vessel and impeller geometries Type: dish-bottomed Impeller type: helical ribbon Details of impellers used No.
T
1 2 3 4 5 6 7 8 9 10
400 400 400 400 400 400 150 150 150 150
D
w
352 352 352 352 352 370 135 135 130 113
34 34 34 34 34 36 13 14 13 12
P 352 352 352 176 190 185 135 75 133 60
P/D
w/D
c/D
1 1 1 0.5 0.5 0.5 1 0.56 1.02 0.531
0.097 0.097 0.097 0.097 0.097 0.097 0.097 0.104 0.100 0.106
0.0682 0.0682 0.0682 0.0263 0.0263 0.0405 0.0556 0.0556 0.0769 0.1637
tib
h/D
HIT
1 2
1.0 1.0 1.0 1.0 1.0 1.0 1.02 1.08 1.02 1.02
1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1
All measurements are in mm. Working fluids Newtonian Uquids: water, silicone oils, lubricating oils, glycerol and various concentrations of sugar solutions Non-Newtonian liquids: aqueous solutions of carboxymethyl cellulose and various grades of chocolate
Results fc=34-144(C/Z)) U^ksN nb
PoRe^Kp=\bO\^ \^)
/
\ /
\0.67
\P\\n
\ l^J W For Non-Newtonian Uquids // can be replaced by IXAUlaLlUIl
c D h H ks I N fib p
clearance between impeller tip and vessel wall, m impeller diameter, m impeller height, m liquid height, m impeller shear rate constant length of impeller blade, m impeller rotational speed, 1/sec number of impeller blades impeller pitch
P Po Re T w YA // fiA p
power input, W power number, P/pN^D^, dimensionless Reynolds number, pNDV^, dimensionless tank diameter, m impeller width, m average shear rate, 1/sec Newtonian viscosity, kg/msec average apparent viscosity, kg/msec Uquid density, kg/cm^
Chapter 3. Power dmw and consumption
178
Sestak. J., Zitny, R. and HouSka, M.MChE Journal, 32,155 (1986) Anchor-Agitated Systems: Power Input Correlation for Pseudoplastic and Thixotropic Fluids in Equilibrium Vessel and agitator geometries
H/D<1 d/D«a9 K/d»at2 h/d*Q89|
^ifti 0d #0
rr #d«3&6mm 2
[3
#d«90 mm 4d»13Smm
#0>4Z8mm #0*100 mm
#D«1S0 mm
I
Dimensions of the anchor impellers (one pair of side arms).
Workingfluids,their physical properties and results Po = C{n)/Re„
3.1 Single phase
179 Summary of experimental results A kgm"^
T, X
Av. C(«)
No. of Experiments
d, mm
1.0 1.0 1.0 1.0
840 900 1,362 1,362
19.9 20.2 24.0 24.3
213.710.7 210.411.0 194.712.5 191.812.9
4 14 14 12
38.6 38.6 90 135
129.98 129.14 130.32 130.15 Polyox WSR in water (1% w/w) 0.794 Wallpaper gum (CMC* in water) 4.973 7.64 67.50 PAA** in water (10% w/w) 80.04 CMC in water (3.8% w/w) 1.2 1.305 15.05 PAA in water (6% w/w) 12.2 13.53 CMC in water (8% w/w) 12.25 11.64 11.637 CMC in water (3.6% w/w) 1.07
0.158 0.0782 0.1215 0.1288 0.62 0.74 0.61 0.816 0.53 0.874 0.810 0.744 0.9595 0.854 0.66 0.70 0.732 0.905
1,424 1,424 1,424 1,424 1.002 1,015 1,015 1,110 1,110 1,014 1,014 1,016 1,016 1,016 1,024 1,024 1,024 1,013
24-32 24-32 24-32 24-32 20.1 20 20 20 20 20.1 20.1 20.1 20.1 20.1 20:2 20.2 20.2 20.1
16.9210.4 15.0610.22 16.4610.22 17.5210.30 62.812.7 99.7211.53 64.7311.37 %.8312.14 43.4211.14 133.9912.15 124.7011.81 80.9611.68 193.311.96 120.7511.53 62.7511.03 73.5311.77 86.4911.30 136.8214.60
12 8 13 12 4 10 5 11 9 13 6 10 7 10 6 7 12 19
135 38.6 38.6 90 38.6 38.6 38.6 38.6 38.6 90 90 90 90 135 90 90 135 135
Thixotropic (equilibrium values): Neoponite No. 1 46.7 Neoponite No. 2 35.9
0.484 0.497
1,929 1,927
21 21
Wallpaper paint
0.249
1,439
21
0.022
1,021
21
44.011.1 39.211.1 39.913.5 23.511.0 19.910.7 21.710.6 8.510.5 5.410.5 5.810.4
11 10 10 11 11 9 9 9 7 305
38.6 90 135 38.6 90 135 38.6 90 135
K, Pas"
Fluids Newtonian: Silicone oil Mineral oil Sugar syrup
0.259 0.9256 2.612 2.531
Pseudoplastic: Kaolin in water (50% w/w)
12.6
n
Laponite in ¥^ter (5% w/w) 300
Total *Carboxymethyl cellulose. **Polyacrylamide.
Notation C (n) d K n N P Po Ren p T
dimensionless function of geometry and n agitator diameter, m constant, Pa(sec)" flow behavior index, r=K'y'*f dimensionless rotational speed, 1/sec power input, W power number, P/(p -N ^'d% dimensionless Reynolds number for power law fluid, N^'^d^plK, dimensionless fluid density, kg/m^ shear stress. Pa
Chapter 3. Pow«r draw and consumption
180
Hirose, T. and Murakami, Y.J. Chem. Eng. Japan, 19,568 (1986) IWo-Dimensional Viscous Flow Model for Power Consumption in Close-Clearance Agitators Results
1 1
Use of published data NpRe=
^ -— TTT—In T" ;r - 4 dsma/Hfib fibO
H'*—
<<2r^\ s
V
^
^ I
H
L-^
s.
<1
k.
r
Nomenclature for agitator geometry.
VESSEL WALL
Two-dimensional flow model. Ota tion b width of blade, m diameter of impeller, m d H height of impeller, m n speed of rotation, 1/sec number of blades fib Np power number, Plpn^d^, dimensionless P power consumption, W Re Reynolds number, pndV^, dimensionless
5 a Pi
s
fi
p
pitch of blade, m inclination angle of blade, rad correction factor 0.9 (paddle) and 0.7 (others) clearance between blade tip and wall, m viscosity, Pasec density of liquid, kg/m^
3.1 Single phase
181
Papastefanos, N. and Stamatoudis, M., Chem. Eng. Res. Des., 67,169 (1989) Effect of Vessel and Impeller Geometry on Impeller Power Number in Closed Vessels for Reynolds Numbers between 40 and 65,000. Experimental apparatus (1)
(2)
square flat-bottomed 28.4
cylindrical flat-bottomed
System Vessel Type One size length (cm) Diameter (cm) Height (cm) Baffle Number Width (cm)
— 28.4 28.4
— 28.4
4or0 2.8
4or0
2.8
mpeller Type Diameter (cm) Number of impellers Number of blades on impeller Length of impeller blade (perpendicular to shaft) Width of impeller blade (parallel to shaft) Disk diameter (cm) Thickness of disk (mm) Thickness of blade (mm)
W 1 6 D/A
(b)~ 14.7 1 6 —
(c) 14.9 1 6 —
D/5
D/5
Z>/5
9.5 2.5 1.2
— — 1.2
— — 1.2
15.0
(a): flat vertical six-blade disk style, (b): flat vertical six-blade open style, (c): 45° pitched six-blade open style
UP
#
€2 (A)
(B)
Schematic diagram or (A) a six-Uade disk style impeller and of (B) a six-Uade open style.
Chapter 3. Pow«r draw and consumption
182
Working fluids and their physical properties Com syrup solutions Viscosity: 7x 10"^ -4Pasec Experimental conditions Reynolds number: 40 — 6.5 x 10* Results
^1 "^T^
r
I
t I 111 „
'
'
« • « I • I I
NR.«
I
1
1 I I M II
_ji
I. I I i n
pND*
Plot of InNp versus InNae for aflatvertical six-blade disk style impeller. ( ® Baffled square vessel, ® Baffled cylindrical vessel, ® Unbaffled square vessel)
Plot of InNp versus inNR, for a flat vertical six-blade open style impeller. ( ® Baffled cylindrical vessel, ® Baffled square vessel, ® Unbaffled square vessel)
3.1 Siiigl«phas«
183
Plot of hiNp versus InNR, for a 45** pitched six-Wade open style impeller. (® Baffled square vessel, ® Baffled cylindrical vessel, (D Unbaffled square vessel)
^ .
Plot of hiNp versus ITINR, for baffled cylindrical vessels. ((D Flat vertical six-blade open style impeller, © Rat vertical six-blade disk style impeller, (3) 45** pitched six-blade open style impeller)
Cha|il«r 3. Powar draw and consumption
184
.^1 '
-J
I I I M111
I
I
_J I I I I HI
I > m 1,1
Re
I
I
I I lilt
10*
H
Plot of InNp versus InNRe for baffled square vessels. (® Flat vertical six-blade disk style impeller, ® Flat vertical six-blade open style impeller, (D 45** pitched six-blade open style impeller)
'-' \2li
"
AAA
7— * ^ 1
t
» I 111
^ s " ^
A
AA^
u
I
i I I tt I
Hot of lni\^^ versus InNRe for unbaffled square vessels. (® Flat vertical six-Wade open style impeller, ® Flat vertical six-blade disk style impeller, (D 45** pitched six-Wade open style impeller)
3.1 Single phase
fotat ion D impeller diameter, m D, disk diameter, m DL length of impeller blade, m Dw width of impeller blade, m gravitational conversionfactor,kgm/kgfsec^ gr N impeller rotational speed, 1/sec Np powder number, PgdpN^D^, dimensionless NR, Reynolds number, pND^I^i, dimensionless P impeller power, W X disk thickness, m viscosity, Pasec ^ fluid density, kg/m^ P
235
Chapter 3. Power draw and consumption
186
Carreau, E J., P^s, J. and Guerin, R, Can. /. ofChem. Eng., 70,1071 (1992) Mixing of Newtonian and Non-Newtonian Liquids: Screw Agitator and Draft Coil System. Experimental apparatus Vessel and impeller geometries
Pathi
Path 2
Path 3
Sketch of the mixing system. System geometry (all dimensions in metres) 1. Vessel: Z)=0.254, if=0.262(C1), 0.255(C2X 0.261(C3) 2. Agitator: £/=0.150, A=0.220, j>=0.147, M;=0.067.rf«=0.0159.cta= =0.012 3. Coils Name
Material
dc
he
du
du
Cbr
ec
He
CI C2 C3
Cr plated Cu Steel Copper
0.1827 0.1763 0.1887
0.205 0.2075 0.2175
0.0127(1/2") 0.00635(3/4") 0.00476(3/16")
0.0095 0.0043 0.0032
0.0275 0.0285 0.0175
0.0060 0.0064 0.0065
10.5 16.5 19.5
Characteristic parameters: D/d=1.69,p/d=0M,
h/d=lA7, w/d=0A5, do/d==0.106, Cba/d==OM,
3.1 Single phase
187
Working fluids and their physical properties Properties of experimental liquids Substance
Cone. (mass %)
M(Pas) or m (Pas")
89.0 91.5 93.5 95.0 97.5 100.
0.14 0.213 0.275 0.408 0.598 0.055 0.200 0.785 2.48 0.564
Glycerol
Vitrae oil HV32 Mixture HV320 Com syrup
* 100. 9|C3|C
CMC
1.0 2.0
Xanthan
0.75
6.27
1.0 1.5
6.5
Polyacrylamide
600mg/L
0.2 1.0
9.5 8.62 0.136 0.521 5.04
n (-) 1.0
\J 0.748 0.631 0.122 0.196 0.183 0.871 0.734 0.521
P
k
Cp
(kg/m^)
(W/mK)
—
g/kg-K) —
0.320 0.315 0.310
2,515 2,480 2,451
1,232. 1,235. 1,240. 1,246. 1,255. 856. 873. 885. 1,383. 996. 996. 995.
—
—
0.145
1,901
\ 0.323 0.588 0.575 0.610
1
2,358 4,177
1
\
\
1,195.
0.356
2,902
\
i
\
•Adjusted for desired viscosity. **Com syrup slightly diluted to avoid crystallization. Properties of distilled water used for solutions: //=9 x lO"'' Pas, p=995.4 kg/m^ ife=0.610 W/mK, c^=417J/kgK.
Results NpICi = 1200/?«/* (1 + 354.8 Wi^"^) where Ci is given by: a = {0.124 + 0.265 [1 - exp (-0.00836/?€^)]}(1 - 0.811 Wi""'^^) Notation Cp specific heat at constant pressure, J/kgK d agitator diameter, m k thermal conductivity, W/mK ks Metzner-Otto constant, dimensionless m power law parameter, Pasec" n power law index, dimensionless N rotational speed, 1/sec Np power number, dimensionless Ni primary normal stress differences. Pa Reg generalized Reynolds number, pN^'*dVmki*'~^, dimensionless Wi Weissenberg number. Nil 2 rj g, dimensionless g shear rate, 1/sec 7] viscosity of non-Newtonian liquids, Pasec ^ viscosity of Newtonian liquids, Pasec p liquid density, kg/m^
Chapter 3. Power draw and consumption
188
Carreau, R J., Chhabra, R. R and Cheng,]., AIChEJournal, 39,1421 (1993) Effect of Rheological Properties on Power Consumption with Helical Ribbon Agitators. Experimental apparatus Vessel and agitator geometries Geometrical characteristics of agitators Geometry
d(m)
D/d
hid
p/d
void
HRl HR2 HR3 HR4 HR5 HR6
0.263 0.263 0.263 0.360 0.360 0.360
1.11 1.11 1.11 1.11 1.11 1.11
1.05 1.05 1.05 1.03 1.03 1.03
0.695 0.850 0.695 0.686 1.030 0.686
0.097 0.133 0.133 0.083 0.133 0.133
• W i«
H h
d
D Sketch of helicalribbonagitator system.
Workingfluidsand their physical properties Rheological parameters of the fluids n Fluids Dilute com syrup #1 Dilute com syrup #2 Dilute glycerol #1 Dilute glycerol # 2 2.5% XTN 0.5%XTN(gly./H2O) 1.8% XTN 0.8% XTN 0.5% XTN 3% CMC 1%CMC 0.4% CMC (gly./HzO) 0.1%CMC(gly./H2O) 0.7% gellan (com symp) 800 ppm PAA (com symp) 0.35% PIB (PB+Kerosene)
(-) 1 1 1 1 0.183 0.199 0.200 0.240 0.250 0.299 0.409 0.530 0.701 0.910 0.940 1
m (Pas*)
U (s)
no (Pas)
12.0 4.16 0.470 0.067 22.4 4.13 11.8 2.31 1.84
0.19
7.83 0.110 9.75 1.20 0.750 10.5 8.19
n^
(Pas)
»' (-)
vfi P (Pas") (kg/m")
0.782
7.85
0.740 1.12
18.0 0.140
1.67 2.00
0.150 1.29
469 1.57
1,440 1,360 1,140 1.100 1,080 1,200 1,080 1,050 1,030 1,060 1,040 1,200 1,200 1,300 1,350 1,100
3.1 Single phase
189
Results 10^
1
I
r
2;
1
1
1
1
• O A • V
^v
' ' " mm»
3%CMC IX CMC 2.6X x m 0.0X XTN 0.7X gdUaa
4
Nvwtoaiui HRa
g z u
10*
Vr
10'
r
10
k-
10
1
il
4
il
1
1
10~*
10"^
10°
lO'
10*
10'
)|k
1 "L-
1
o
a.
^ " " " ^ J
10*
Generalized Reynolds Number, Re^
g
Power data for the shear thinning inelastic fluids.
0)
3 o a.
Generalized Reynolds Number, Re Power data for the viscoelastic fluids.
^9Q
Chapter 3.
Power draw and consumption
Notation agitator diameter, m d D vessel diameter, m h impeller height, m H height of liquid in the vessel, m Kp proportionality constant of the power number, Np=KpT]e/(d^Np) m power law parameter, Pa(sec)" m' parameter, PaCsec)" n power law index n! parameter N impeller rotational speed, 1/sec Np power number, P/d^N^p, dimensionless p impeller bitch, m P power, W Reg generalized Reynolds number, d^Np/rje, dimensionless h Cross model parameter, sec w impeller width, m Ye effective shear rate, 1/sec T]e effective viscosity, ?]«=m | ye | "'S P a s e c Tjs solvent viscosity, P a s e c r]o zero-shear viscosity. Pa-sec p liquid density, kg/w?
3.1 Single phas«
191
Kamei, N., Hiraoka, S., Kato, Y., Tada, Y., Shida, H., Lee, Y-S., Yamaguchi, T. and Koh, S.-T, Kagaku Kogaku Ronbunshu, 21,41 (1995) Power Correlation for Paddle Impellers in Spherical and Cylindrical Agitated Vessels Experimental apparatus Vessel System Vessel Type Diameter (mm) Baffle Impeller Type
(1)
(2)
spherical 163,190 no
flat-bottomed 130,145,170 no
paddle
paddle
Diameter (mm) Width of blade (mm) Number of blades on impeller
57, 76,95 19,28,38,76 2,4,6,8
1
Number of impellers
Working fluids Ion-exchanged water, glycerin solution and com syrup Results For cylindrical vessels
f Rec
={
Kr]\a(D/d)
C, = [{1.96 ( y < ' 6 / f f ) " ' } - ' ' +(0.25)-'-']-*"-' m = [{Q.nOiynfblDf'^y''^ Cir = 23.8
+(0.333)-'-']-'''•'
(d/Dr'^ib/DT'^irn^'b/H)-"*
/-=7.56xlO-^(rf/D)C,°'
1
192
Cha|it«r 3. Pow«r draw and consumptioii
^ p -
2HD/d) [D/d)-(d/D) 171110.157+inpHD/d)}'-'''] n'p^Hl-(d/D)'} 1/3
7 ='
r]\xi{Dld)
^ (PD/df
For spherical vessels
(4VY" =0.874A
Z)= ± 1 .
Notation b height of impeller blade, m d impeller diameter, m D diameter for qrlindrical vessel, Da diameter for spherical vessel, m H liquid height, m Up nmnber of impeller blades N rotational speed, 1/sec Np power number, P/pN^d^, dimensionless P power consumption, W Red impeller Reynolds number, Nd^p/fi, dimensionless V volume of spherical vessel, m^ fi viscosity, Pasec p density. kg/m^
3.1 Single phase
193
Mochizuki, M., Takei, N., Satoh, K. and Akehata, T, Kagaku Kogaku Ronbunshu, 21,628 (1995) Power Required for Upper and Lower Impellers in Turbulent Mixing Vessels with Dual Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 300 mm Liquid contained Height: 300 or 600 mm Baffle Number: 4 Width: 30 mm Impeller Type:flatblade disk turbine (D) downward pumping-45° pitched blade turbine (Pd) upward pumping-45° pitched blade turbine (Pu) Diameter: 100,125 and 150 nun Number of impeller: 1 or 2 Number of blades on impeller: 6 Blade width: d/5 hi
D-D h2/dT>0,S others /i2/rfr>l/3 Working fluid Tap water Results
Power numbers for dual impellers with 0.1 m diameter (O: D-D, A: Pd-Pd, D: Pu-Pu, A: Pd-Pu, • : Pu-Pd, ©: D-Pd, O: Pu-D, • : D-Pu, V: Pd-D).
Chapter 3. Power draw and consumption
194
1|—I—I—I—r-
1
1 1 \
r
I
L
Q.
2
0.5
2 Relative power required for upper and both stage in dual impellers, Np, u/Np,t (O: D-D, A: Pd-Pd, D: Pu-Pu, A: Pd-Pu, • : Pu-Pd, ©: D-Pd, O: Pu-D, • : D-Pu, V: Pd-D).
I
1
L_J
I
10
JL d D-Pddual
Pd-Pd dual
Effect of impeller diameters on power (O: d = 10 cm, A :rf= 12.5 cm, D: = 15 cm).
0.5 h?/dT
Notation d dr hi hz hs n Np P p
diameter of impeller, mm or m diameter of vessel, mm bottom clearance of impeller, m impeller spacing, nmi distance between the upper impeller and water surface, nmi rotational speed of impeller, 1/min power number, P/pn^d^, dimensionless agitation power input, W liquid density, kg/w?
Subscripts t total (dual impellers) U upper impeller
H
I
3.1 Single phas«
195
Brito-DE la Fuente, E., Choplin, L. and Tanguy R A., lyans. Instn. Chem. Engrs., 45, P^t A, 75 (1997) Mixing with Helical Ribbon Impellers: Effect of High Shear Thinning Behavior and Impeller Geometry Experimental apparatus Vessel Type: (1) (2) flat-bottomed Diameter: (1) 0.210 (2) 0.435 m Liquid contained Height of liquid/height of impeller: 1.14 Impeller Type: helical ribbon screw impeller
Helicalribbonscrew impeller (all dimensions are in m). Geometrical ratios of impellers used'.
Impeller Type
D/d"
HRS-IA HRS-2A HRS-IB HRS-2B HR-IB HRS-1.5
1.135 1.135 1.135 1.135 1.135 1.135
hid
w/d
s/d
Ws/W
Ss
0.108 0.108 0.162 0.162 0.162 0.135
1.0 0.5 1.0 0.5 1.0 0.7
1.25 1.25 1.17 1.17 1.20
0.370 0.185 0.370 0.185 0.247
' All dimensions in m. ** The mixing vessels diameter, Z)=0.210 m.
296
Chapter 3. Pow«r draw and consumption
Working fluids, their physical properties and experimental conditions Rheological properties of the fluids. Fluid
Power law model parameters ^' ^
Range ^
w = 1.0; w = 33.67 « = 1.0; w = 6.69 « = 1.0; m = 0.17 n = 0.359 w = 113.8-1.7200 n = 0.0916 + 3.0 x 10-^0 m = 5.0817 - 5.42 x 10-^0 n = 0.1377; m = 21.34 n = 0.904 - 8.29 x 10-^0 m = 0.738 -1.74 x 10-^0 n = 0.372 + 1.28 x 10-^0 m = 11.3-0.1770 n = 0.6044; m = 14.8765 n = 0.19; w = 9.7
0=25 0=25 9 = 22.5 12 < 0 < 30 l
PB96%-KER4%(NEW1) PB91%-KER9%(NEW2) GLY 90% - H2O 10% (NEW 3) CMC 3% (VEl) XTN 0.5% (PSTl) XTN 3% (PST2) CMC 0.5% (PST3) CMC 1.5% (PST4) CMC 1.5% (PST5) Gellan fermentation broth (PST6)
* The power law model: ti^my"'^. ^ 0 in **€; 7 in s"*; m in Pas". PB=polybutene; KER=kerosene; GLY=glycerol CMC=carboxy methylcellulose; XTN=xanthan.
Results •0.72 /
Np=-
>v0.l4
w
Np=173ARe-^
D
,,
197
3.2 Multi phase 3.2.1 Solid-liquid systems Raghav Rao, K. S. M. S. and Joshi, J. B., Chem. Eng./., 39, 111 (1988) Liquid-Phase Mixing and Power Consumption in Mechanically Agitated Solid-Liquid Contactors Experimental apparatus Vessel Type: (1) (2) flat-bottomed Diameter: (1) 0.57 (2) 1.0 m Liquid contained Height: (1)0.57 (2) 1.0 m Baffle Number: (1) (2) 4 Width: (1)0.057 (2) 0.10 m Impeller Type Diameter (m) Vertical blade height (m) Horizontal blade length (m) Angle of pitch (degree) Blade thickness (m) Disk thickness (m) Number of impellers Number of blades on impeller Off-bottom clearance
DT 0.19 D/b D/4 — 3x10-' 4x10-3 1 6
PTD 0.1425,0.19,0.25,0.33 0.03,0.04,0.063,0.07 0.045,0.075,0.10,0.14 45,45,45,45 3 X10-3
— 1 6 r/6, r/4, r/3, r/2
DT: disc turbine PTD: pitched blade turbine downflow PTU: pitched blade turbine upflow Working fluids, solids and their physical properties Liquid: tap water Solid: quartz particles shape: granular average particle size: 100—2,000 ^m density: 2,520 kg/m' terminal settling velocity in water: 34-165 mm/sec
Experimental conditions
Impeller speed: 2—13.3 rps Solid loading: 0-40 wt%
PTU 0.19 0.04 0.075 45
3x10-3 1 6
293
Chapter 3. Pow«r draw and consumption
Results (1) Effect of impeller design the power required for suspension by menus of a PTD impeller is much lower than with PTU and DT impeller (2) Effect of loading PTD,DT NpsL ocX'-'' PTU NpsLocX''''' (3) Effect of particle size PTD, PTU NpsLocdp'"* DT iNfeiocrf/oe (4) Effect of impeller diameter (5) Effect of tank diameter
Notation dp D Ncs NpsL iPm)cs T X
average particle size, ^m impeller diameter, m critical impeller speed for sohd suspension (soUd-liquid system), 1/sec power for solid-liquid system, dimensionless power consumption per unit mass at Ncs (soHd-liquid system), W/kg tank diameter, m solid loading, wt%
3.2 Multiphas*
199
3.2.2 Gas-liquid systems Oyama, Y. and Endoh, K., Kagaku Kogaku, 19,2 (1955) Power Characteristics of Gas-Liquid Contacting Mixers Experimental apparatus Vessel Type: flat-bottomed Diameter: (1) 16.5 (2) 20 (3) 27.4 cm Liquid contained Height: (1) 16.5 (2) 20 (3) 27.4 cm Baffle Number: (l)-'(3) 4 Width: (1)~(3)Z)//10 Impeller Type: paddle, vaned disk, andflatblade turbine Geometry:
—i-
Paddle A/A = 1/3 P^/A = l/4
Vaned disk A/A = 1/3 Pr./A-1/3.05 A / A = 1/3.38
Flat blade turbine A/A = 1/3 W A = 1/3.94 A / A = 1/3.22 A / A = 1/1.30 Experimental impellers.
Off bottom clearance: A/3 Sparger Type: a single nozzle Diameter of nozzle: 1.5 and 6 mm Working fluids Liquid: water Gas: air Experimental conditions Air rate: maximum 600 cc/sec Temperature: 19°C
Chapter 3. Pow«r draw and consumption
A: r u t bUd iartHnc(N;«8) 6^ Vdfieddtsk (Ni-8) C- Vo/ieddisft (Ni«6) 0- Varied disk** (Ni«l6) (Ni«4) p: Paddle
4
6
d
10
Power characteristics of gas-liquid contacting mixers. Notation A impeller diameter, cm tank diameter, cm A impeller rotational speed, 1/sec n QalnD?, dimensionless NA Ni number of impeUers power consumption under aeration, kgf/msec P. Po power consumption without aeration, kgf/msec volumetric rate of air, cc/sec Qa impeUer width, cm Wi
12
J4
3.2 Multiphas*
201
Bruijn, W, van't Riet, R. and Smith, J. M., Trans. Instn. Chem. Engrs., 52,88 (1974) Power Consumption with Aerated Rushton Turbines Experimental apparatus Vessel Type: flat-bottomed Dimension: 50 cm x 50 cm Baffle Number: 4 Impeller Type: a standard Rushton Diameter: 7£ cm Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: 25 cm Sparger Type and diameter Type
Diameter (10"^ m)
open type ring sparger ring sparger ring sparger
0.5 2.3 5.0 7.4
Working fluids Liquid: Liquid Water Water Water Kerosene Gas: air
Addition
CT(N/mxlO-3)
12.5 weight % NaCl 0.83 vol % Teepol
73 76 28 26
Chapter 3. Power dmw and consumption
202
Results (1) the influence of surface tension and dissolved ionic solutes
1 r|—
1
1
r
,
1
$K
z
8 o«
A
1
"•
•
Ui
H
A
§
! *•
a.
K
S06
A
•
< Ui 1 1
5?
• — J » i :
1 » L 001 0O2 a09 0//V0'—OiMENSONLESS GAS MFLOW RATE
0
Symbol # V X A
Ko Fluid 5-5 distilled water 5-3 12-5 weight %NaCl 5-4 0* 83 volume % Tccpol 5-4 kerosene Square vessel, D « 7-6 cm / / = 14s-*
004
Re 81,000 81,000 81,000 49,400
Power consumption curves with different fluids. (2) the influence of the number of blades
0
OOS 0^0 O'lS 0//V0'-OIMENSIONLESS GAS INFLOW RATE
Symbol Number of blades Ko A 6 5-6 O 9 8-6 X 12 100 • 18 120 Square vessel, i> = 7-6cm N^ 12s-* Fluid: distilled water Re = 69,300 Power curves for stirrers with different number blades.
3.2 Mumphas*
203
(3) the influence of the gas spargers «
t
i • •«
%
• •. • i
«
«
uj 0 oc
I 02] 0«t
Symbol X O
Sparger diameter 0' 5 cm 2-3 cm 5*0 cm + 7*4 cm • Square vessel, Z) = ?• 6 cm N^ 10s-* Fluid: distilled water Re « 57,800 Ko « 5-4
Power curves for different gas spargers. Notation D stirrer diameter, m power number, Po/pN^D^, dimensionless N stirrer speed, 1/sec gassed power consumption, Nm/sec Pi ungassed power consumption, Nm/sec Po gasflowrate, mVsec Q Re Reynolds number, pNDVr], dimensionless liquid viscosity, Nsec/m^ r] density, kg/m^ P a surface tension, N/m
«
- ^
204
Chapter 3. Power draw and consumption
Loiseau, B., Midoux, N. and CharpentierJ.-CAIChE Journal, 23,931 (1977) Some Hydrodynamics and Power Input Data in Mechanically Agitated Gas-Liquid Contactors Experimental apparatus Vessel Type: flat-bottomed Diameter: (1) 22 cm (2) Volume: 8.9 (2) 5.5^ Liquid contained Dispersion height: (1) 22 cm (2) T Baffle Number: 4 Width: 2.2 cm Impeller Type: a sixflat-bladeRushton disk turbine Diameter: T/3 Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: T/3 Sparger Type: (1) an open tube (diameter 0.8 cm) (2) a perforated ring (diameter 6 cm; thirty holes; diameter of hole 0.1 cm) (3) a porous ring (diameter 6 cm) Location: beneath the turbine Working fluids and their physical properties Liquid: Type of liquid
Liquid
P,10^ kg/m^
M. 10-^ Pas
cj, 10-3
N/m
Pure hquids
Water Glycol
1.0 1.11
1.0 19.75
72.0 48.1
Nonfoaming solutions
Water + lauric Alcohol (1.7 p.p.m) Ethanol (95% by volume) Water + sugar (60 wt %)
1.0
1.0
23.0
0.803 1.278
1.50 48.50
23.9 53.5
1.145 1.028
1.25 L12
44.4 61.0
1.024 1.158 1.085
1.22 5.40 1.50
28.0 54.0 56.1
Foaming solutions
Gas: air
Water + HCl (5N) + CuCl (0.9 M) Aqueous sodium Sulfite sodium (0.2 M) Acetic acid + propionaldehyde (2 M) Water + sugar (36 wt %) Aqueous sodium* Sulfite solution (0.8 M)
3.2 Multiphase
205
Experimental conditions Type of liquid Pure liquids Nonfoaming solutions
Foaming solutions
Us,
Liquid Water Glycol Water + lauric Alcohol (1.7 p.p.m) Ethanol (95% by volume) Water + sugar (60 wt %) Water+ HCl(5N) + CuCl (0.9 M) Aqueous sodium Sulfite sodium (0.2 M) Acetic acid + propionaldehyde (2M) Water + sugar (36 wt %) Aqueous sodium* Sulfite solution (0.8 M)
Np 3.80 ±0.15 Variable with Re 3.72 ±0.11
10-2 m/s 0.07-2.12 0.07-0.62
rev/min 340-1,650 350-1,400
0.07-0.62
440-1,500
3.59 ±0.15 Variable with Re 3.38 ±0.08
0.07-0.62 0.07-0.62
380-1,600 400-1,400
0.64-4.7
480-1,720
3.68 ±0.11
0.27-2.12
340-1,625
3.28 ±0.13
0.27-2.12
350-1,500
3.15 ±0.11 4.56 ±0.11 3.63 ±0.12
0.07-0.62 0.07-8.5
400-1,650 300-3,000
*iV^=4.56 for r=0.19 m, Vi:=5.5 x 10"^ ml 7V^=3.63 for 7=0.22 m, V)r =8.9 x IQ-^ m\
Results Pa=C
PoND^ Q .0J56 G
= CM"
For nonforming systems Pa = 0.83Af°-^ For forming systems if M<2xl0^ ft = 0.69M°-^ or P . = 1.88M°-3i iif M>2xl0^ Notation C constant D agitator diameter, m n exponent N rotational speed of impeller, 1/min Np power number. PaIpN^D^, dimensionless Pa aerated power input by mechanical agitation, W PQ unaerated power input by mechanical agitation, W QG volumetric flow rate of gas, mVsec T tank diameter, m Us superficial gas velocity based on the cross section of the tank, m/sec VL liquid volume, m^ H liquid viscosity, P a s e c p liquid density, kg/m^ G liquid surface tension, N / m
205
Chapter 3. Power dmw and consumption
Matsumura, M., Masunaga, H., Haraya, K. and Kobayashi, J.,/. Ferment. TechnoL, 56, US (1978) Effect of Gas Entrainment on the Power Requirement and Gas Holdup in an Aerated Stirred Tank Experimental apparatus Vessel Tjrpe: flat-bottomed Diameter: 218 mm Liquid contained Height: 218 mm Baffle Number: 3 Width: 25 mm Impeller Type: six-blade turbine Diameter: 0.487 Z)T Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: DT/3 Sparger Type: a single nozzle Location: underneath the impeller Working fluids and their physical properties Gas: air Liquid: water, ethyl alcohol, benzyl alcohol, ethylene, glycol and sucrose solution viscosity: 0.8-30 cP surface tension: 22^^71 dynes/cm densities: 0.8—1.3 g/cm^ Experimental conditions Impeller speed: 7.08—16.5 rps Superficial velocity of sparged gas: 5 x 10"*—1 x 10"^ m/sec Results ^1_ = 1.913xlO-^^iVx)-'-'(7\^i..f ^(7\r,K./^(7\r^.r f ^ l (l-r?)' 3x10'^
7xlO^
BxlO^
6x10'^
KNFT
<3
3.2 Multi phas« Notation Di impeller diameter, m DT tank diameter, m / volumetric flow rate of entrained gas, i/min gr gravitational conversion factor, kg-m/kgf sec^ N rotational speed of impeller, 1/sec NA Aeration number, VslNDi, dimensionless NA modified aeration number, VTINDU dimensionless Npr Froude number, N^Di/go dimensionless N^ power number in gassed liquid, PggdpN^D^, dimensionless NRe Reynolds number, ND?pl\i, dimensionless Nwt Weber number, N^D?pla, dimensionless Pg power consumed in agitation of gassed liquid, kgf m/sec 0 volumetric flow rate of gas sparged from the tank bottom, ^/min Vs total gas volume dispersed in tank, ^ VT overall superficial gas velocity, calculatedfiromthe sum of Q and/, m/sec p density of liquid, kg/m^ a surface tension of liquid, g/sec^
207
20g
Chapter 3. Power draw and consumption
Gray, D. J., Treybal, R. E. and Barnett, S. M.,AIChE Journal, 28,195 (1982) Mixing of Single and Two Phase Systems: Power Consumption of impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.762 m Liquid contained Height: 0.5 m Volume of liquid in vessel: 0.232 m^ Baffle Number: 4 Width: 0.0762 m Impeller Type: sixflat-bladeturbine Diameter: 0.1524 m Number of impellers: 1 Number of blades on impeller: 6 Off-bottom clearance: 0.0762 and 0.178 m Working fluids Liquid: water Gas: air Results g'TC
-^^^^^ = 0.75 {VG/^GYN'D^ NW^PL
with use of data taken by Bimbinet (1) and Hassan and Robinson (2) (1) Bimbinet, J. J., Air-Liquid Contacting in Mixing Vessels, Holdup and Flooding, M. S. Thesis, Dept. of Chem. Engr., Purdue Univ., Lafayette, IN (1959) (2) Hassan, I. T. M. and Robinson, C. W.,AIChE Journal, 23,48 (1977) Notation C impeller height off the tank bottom, m D impeller diameter, m g local gravitational acceleration, m/sec^ gc gravitational constant, kgm/kgf sec^ N impeller rotational speed, 1/sec PT total power input in gas-Uquid dispersion, W T tank diameter, m VG superficial gas velocity, m/sec 0G volumefractionholdup PL mass density of Uquid, kg/w?
3.2 Multi phas«
209
Lu, W.-M. and Ju, S.-J., Chem. Eng. Set., 44,333 (1989) Cavity Configuration, Flooding and Pumping Capacity of Disc-Type Turbines in Aerated Stirred Tanks Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.288 m Liquid contained Height: 0.288 m Baffle Number: 4 Width: 0.0288 m Impeller Type Diameter (m) Number of impellers Number of blades on impeller Length of impeller blade (perpendicular to shaft) Width of impeller blade (parallel to shaft) Off-bottom clearance
A
B
C
0.072,0.096,0.142
0.096
0.096
1 6 D/4 D/5 T/3
1 4
1 8 D/4 D/b T/3
Z)/4
D/b T/3
A: standard 6-flat-blade disc-type turbine B: 4-flat-blade turbine C: 8-flat-blade turbine
Sparger Type: a perforated ring Diameter of ring: 0.08 m O.D. of ring tube: 0.00635 m Holes: 2 mm holes drilled every 2 cm Location: 3.5 cm below the impeller
Working fluids Liquid: tap water Gas: air
Experimental conditions The operating conditions for impeller pumping capacity measurements under aeration D (cm)
fib
7.2
6
9.6
6
N Q (rev min~*) Wmin) 550 10.6 650 10.6 800 10.6 800 21.3 650 21.3 800 31.8 275 10.6 400 10.6 500 10.6 500 21.3
D (cm)
fib
9.6
6
14.2
6
9.6
N
4
Q
D
(rev min"*) (i/Tmn) (cm) 400 500 155 185 230 230 185 230 350 450
21.3 31.8 10.6 10.6 10.6 21.3 21.3 31.8 10.6 10.6
fib
9.6
4
9.6
8
N Q (rev min"') (^/min) 550 550 450 550 225 325 400 400 325 400
10.6 21.3 21.3 31.8 10.6 10.6 10.6 21.3 21.3 31.8
220
Chapter 3. Pow«r draw and consumption
Results Xa412 / _ \131
OL =1.25x10 ' ""
--(Clf)
(4.07+ 1.21«6-0.147M*)
where ^4=0.072 for the highest limit of impeller flooding andi4=0.064 for the lowest limit of gas dispersion.
Notation D g nh N NF Fg 0 QL T y
impeller diameter, m gravitational acceleration, m/sec^ number of blades on impeller impeller speed, 1/min flooded impeller rotational speed, 1/sec impeller power consumption under aeration, W air flow rate, mVsec impeller pumping capacity, mVsec tank diameter clear liquid volume, m^
3.2 MuttiphaM
211
Hudcova, V, Machon, V and Nienow, A. W, Biotch. andBioeng., 34,617 (1989) Gas-Liquid Dispersion with Dual Rushton Turbine Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.56 m Liquid contained Height:/f/r= lor 2 Baffle Number: 4 Width: 0.1 T Impeller Type: 6-blade Rushton disc turbine Diameter: Z)/r= 1/3 Number of impellers: 1 or 2 Number of blades on impeller: 6 Distance between two impellers when two impellers are employed: AC; 0.2Z)~3.0Z) Off-bottom clearance: T/3 Sparger Type: a ring sparger Diameter: 0.1 m Number of holes: 16 Diameter of each le: 0.002 m Working fluids Liquid: water Gas: air Results 1^
10 0-8
1^
T
T
V Upper impeller {PqlP)n,2 ^ Lokrer impeller {PqlP)n,\ O Both Impellers
0-6 04 0-2
1vvm(for H=T); H=2T; AC/D»1 J-
_L
002
004
J-
006
008
J
0-10
0-12 Fir,
(a)
i
I
L
OH
0-16
0-18
0-20
0*22
Chapter 3 . Power draw and consumption
212
^
10
,
^
1
^ Upper impetler [PilPh.i A Lover impeller (P,/P)„,i O Both impellers
0-8 0-6 0-4 0-2
h vvm ( for H=T); H s 2 T ; J-
AC/D«1
-L.
0-04 006 008
002
-L.
010
0-12 0-14
Flo (b) Pg/P versus Be at AC/D = 1 at constant aerationrate;(a) Qc = 2.3 x 10"^ mVs; (b) QG = 1.15 x 10"^ mVs.
—1
1 — ~r a O y A X
10
08
^^/° 02 05 10 15 30
N«325s*' H
p * X
a
06
J
04
0 ^—•
S o S O g A
V A
V A A
7
7 A
° A
Single impeller
-J 0 02
L
. , !.— . .1 0 04
0 06
0 08
1 010
1- — - L 012 OK
1 016
(Pg/P)2 versus Flc, N = 3.25 s" \ *Eq.
(JPg/P)2 = 0.5m/P)i
+ 1 -SG}
J 016
1 0 20
1 0 22
3.2 Multiphase
n
213
1
1
1
1
\
1
1
AC/0 = 10
1
r
N«2-5s"^
(<JG)F.„-2 •A—
.
^
—7—7—7^ OX
V
Upper impeller (Pg/P)n=2
A
Lower impeller (Pg/P)n=i
A
A , „-... A -
A
7
.
..7
A—A "
V
'V
02K 0
I 002
I OOA
i 006
I 008
I 010
012
J OR
I 016
Pg/P versus Flc for the individual impellers, AC/D = 1.0.
Notation AC distance between two impellers, m impeller diameter, m D gas flow number, QG/ND^, dimensionless FIG liquid height, m H stirrer speed, 1/sec N minimum speed to prevent flooding, 1/sec NF power drawn number ungassed conditions, W P power drawn under gassed conditions, W P. gas flow rate, mVsec QG T vessel diameter, m gas holdup EG Subscripts 1,2 « = 1, n = 2 F
a single or two impellers, respectively the lower and upper impeller, respectively at theflooding-loadingtransition
{ 018
L 0-20
214
Chapter 3. Power draw and consumption
Abrardi, V, Rovero, G., Baldi, G., Sicardi, S. and Conti, R., lyans. Instn. Chem. Engrs., 68, Part A, 516 (1990) Hydrodynamics of a Gas-Liquid Reactor Stirred with a Multi-Impeller System Experimental apparatus Vessels and Impellers Vessel Type Diameter (cm) Liquid contained Height (m) Baffle Number Width (m) Impeller Type
flat-bottomed 0.39
flat-bottomed 0.39
0.39
0.65
4 0.04
4 0.04
6DT,4MFD,4MFU
6DT-6DT, 6DT-4MFD, 6DT.4MFU
Diameter (m) T/3 Number of impellers 1 Positions of impellers Distance between bottom r/3 and thefirstimpeller Distance between 1st — impeller and the second impeller 6DT: six-blade disk turbine 4MFD: pitched blade mixedflowturbine, pumping downward 4MFU: pitched blade mixedflowturbine, ptunping upward Sparger Number of holes: 8 ID of hole: 2 nun Location: beneath the stirrer Working fluids Liquids: water Gas: air Experimental conditions Gasflowrate: 5 x 10-*-2 x 10"' mVsec Stirrer speed: 150—800 rpm
r/3 2
r/3 21/3
3.2 MultiphaM
215
Results
QG
Symbol •
•D
A
o
•
mVs
wm
0 5.0010" 7.6710-" 1.0710-' 1.5310-' 2.0010-'
0.386 0.593 0.825 1.185 1.546
/ = bottom impeller in flooding conditions.
Power number vs N for the 6DT-6DT system. See a table attacned for symbols.
7^
Po,
A j l A J A ^ A A
65-
\ ^ - . ^ . . ^ffv^'Sn D-fl'i^^fiuja-n-'?-
4-
3-
/^V^^4-S5!tS^
2-1
200
1
T"
600
1
1
200
N (rpn) Power number vs N for the 6DT-4MFD system. See a table attached for symbols.
POG QG
T
1
400
1
1
1
600
H(rp«) Power number vs N for the 6DT-4MFU system. See a table attacned for symbols.
Notation D N P
1
stirrer diameter, m stirrer velocity, 1/sec or 1/min power, W power number under gassed conditions, P/N^D^, dimensionless gas flow rate, mVsec tank diameter, m
1
Chapter 3. Power draw and consumption
216
Smith, J. M. and Katsanevakis, A. N., Thzns. Instn. Chem. Engrs., 71, Part A, 145 (1993) Impeller Power Demand in Mechanically Agitated Boiling Systems Experimental apparatus Vessel Type: dish-bottomed Diameter: 0.44 m Impeller A 240,180,130 1 6
Type Diameter (mm) Number of impellers Number of blades on impeller Length, width, and thickness of blade and disk
B 180 1 6
225,200,165 1 6
shown in afigureattached
A: Rushton turbine B: Hollow blade impeller (blade concave-convex turbine) C: 45° pitched blade impeUer
nm
36
t=
022D
02D
1
-H0.25 OU-^
6 Blade Rushton D ^ 240. 180 and 130 mm
D s 225. 200 and 165 mm
0.20
^
^
-HO.25
D s 180 mm 6 Blade Concave-Convex turbine Working fluid Boiling water
_n
6 Blade PB turbine
R-O.UD
A
1
3.2 Multiphase
217
Results 5UILS /
\0.4
(/?PZ)) = ^ = constantffi. A { vf J Notation g PB Pu RPD S Vi
acceleration due to gravity, m/sec^ power consumption in boiling system, W ungassed power demand of impeller, W relative power demand impeller submergence below free liquid surface, m tip speed of impeller, m / s e c
Chapter 3. Power draw and consumption
218
Mochizuki, M., Takei, N., Satoh, K., Akehata, T. and Miyauchi, T, Kagaku Kogaku Ronbunshu, 19, 560 (1993) Power Required for Upper and Lower Impellers in Gas-Liquid Stirred Vessels with a Dual Turbine Experimental apparatus Vessel Type: flat-bottomed Diameter: 300 mm Liquid contained Height: 300 or 600 mm Baffle Number: 4 Width: 30 mm Impeller (1) Type Diameter (mm) Impeller width (mm) /i2(mm)
hi (mm)
100 20 5-30 75
(2) flat six-blade disk turbine 125 25 5'-30 75
(3) 150 30 5-30 75
Working fluids Liquid: tap water Gas: air Experimental conditions Air flow rate: 8.3 x 10-^-7.5 x 10* mVsec (20°C, 1 atm) Results
Power requirements for dual turbines with a large impeller spacing. NA
1-1
3.2 MuKi plias«
219 10
cT 0-5
d n
O A D
» 10 ca « 400 rp»
Power requirements for dual turbines with a small impeller spacing. -L 0
Dual iapcller : Both (h ,/d «0.5) : Upper : Lower Sinjle iapellcr I
I -L
&05
J0-10
N A I-I
(Single impeller: liquid height = 300 mm; flat six-blade disk turbine (d = 100 mm))
Notation d hi hz n NA P Qg
impeller diameter, mm bottom clearance of lower impeller, mm impeller spacing, mm rotational speed of impeller, 1/sec gas flow number, Qg/nd^, dimensionless agitation power input, W gas flow rate, mVsec
Subscripts 0 unaerated g aerated
220
Chapter 3. Pow«r draw and consumption
Bakker, A. and Van den Akker, H. E. A., lyans. Instn. Chem. Engrs., 72, P ^ A, 573 (1994) Gas-Liquid Contacting with Axial Flow Impellers Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.444 m
Liquid contained Height: 0.444 m
Baffle
Number: 4 Width: 0.077 T Clearance of baffle from wall: 0.023 T
Impeller Type SR(%) Rt.i(%)
A 315 90 77
Hb
Leeuwrik
160 80 6
4
Dim) Blade width (m)
0.168
0.178 -
—
Off-bottom clearance (m)
PBT 60 45 6 0.176 0.2 Z>
0.75 Z) or Z)
CD - ^bAb
p
*JI\ — ^~~~'~"
J\b, 1 — —————
_
flbAb,1
ED' E(D'- dL) 4 4 PBT: down wards pumping pitched blade turbine, 6 blades at 45° blad
Sparger Type
dsim)
a pipe sparger (PS) a small ring sparger (SRS) a large ring sparger (LRS) a quadruple pipe sparger (QPS)
0.4 Z> 0.75 Z)
—
Working fluids and their physical properties liquid: distilled water glycerol solutions (1) viscosity = 36 mPasec density = 1,190 kg/m^ (2) viscosity = 80 mPasec density = 1,220 kg/m^ Gas: air
221
N»4Ht
.J
I
I
I
I
t.
Power curves for the PBT at constant impeller speed.
Pg/p. o
Vtg
•
OJOOS
m/i
- ^ Vag • 0.011 m/t
A 3 ^ • U r o * Mno 8p«ro«r
mJ.
Power curves for the A315 at constant impeller speed.
t.. 1 . I
I
I
t
Power curves for the A315 at constant superficial gas velocity Q^rgeringsparger). . Pc/V|
{iH/m"9)
e v«o-aoo$m/« « VsQ • oxm M/s •
Vsg .
QLOW
m/a
100
• Laro«Mno tparftr
0
•
•
'
'
'
•
•
•
•
'
•
•
•
•
.1
v«a ("•/•) Power curves for the PBT at constant superficial gas velocity.
The minimum power consumption necessary to prevent direct loading.
Chapter 3. Pow«r draw and consumption
222 16
J h [
' »
J9^^^^
• M mPas ^ • 10 fflPM
»•
.7
'*»^«,^
fn^:* ^
y
N^
r I
H A315 • LAS • 8/0 - 0.1 - Vtg • 0.01 m/t
I [• I
0 4Hi • SRS • 7 Nz • 4 HI « 7Hx
1—1
1 1 1
1
>
» 7"^r^ \ A318 • Cn* • 0.4
t
1
-
>'''*'''^^"**>^_
^^y*^
>v,»
1
, 1 ,.A
1
1
1
1
*^^/^
J
1
•
"5^ \
'
•
y
A
1
1
1 1
A
•
•
•
'
•
1
t
1
l _ _J
—1—1
t —
.00
Power curves for the A315 with a small ring sparger and a pipe spaiger at constant impeller speed.
Power curves for the A315 at three liquid viscosities,
,Po^u L r
Vsg - 0.00$ ml% Vag - OJOIO m/t
y -11
n
•—o *
L
..v-o-1
-
T
T
\ •^
Y
Vtg « OJm m/t
«'—«
—.-i
o 4 Hx • S/O • 0.7
\ • 7Hi A31S . C/T - 0.4 I «4Hl • t/D«OJ O i M l M n f 8paro«r k • 7Hx L L i — J - J „ l - . - l . . *._L- i—X ,^L_t., i 1 1 1 i 1
P«T - M mPa* • U r o * Mifl Spwo^ 1 1
J4
Power curves for the A315, amall ring, sparger, two impeller to sparger separation distances, constant impeller speed. Notation Ab area of one impeller blade Ah, 1 projected area of one impeller blade C impeller to bottom clearance dkub impeller hub diameter dt sparger diameter D impeller swept diameter Fig gasflownumber Ub number of impeller blades N impeller rotational speed P power consumption Po impeller power number 5 impeller-spaiger separation T vessel diameter % superficial gas velocity Wi liquid v o l u m e Subscripts g gas under gassed conditions u ungassed conditions
.1 .1
.02
L. .04
M
Jl
Power curves for the PBT at 80 mPa s.
.1
3.2 Mutti phas«
223
Smith, J. M. and Tarry, K., Trans. Instn. Chem. Engrs., 72, P&rt A, 739 (1994) Impeller Power Demand in Boiling Solutions Experimental apparatus Vessel Type: dish-bottomed Diameter: 0.44 m
Impeller
Type: Rushton impeller Diameter: 0.18 m Number of impellers: 1 Number of blades on impeller: 6 Submergence: 0.3 m Working fluids 5 and 10 wt% NaCl solutions Results
A.„.76ter BJ
[vf
)
Notation g acceleration due to gravity, m/sec^ PB power under boiling conditions, W Pu power under ungassed conditions, W S impeller submergence, m Vi impeller blade tip velocity, m/sec
224
Chapter 3. Pow«r draw and eonsumptloii
Cheng, J. and Carreau, R J., Chem. Eng. Sd., 49,1965 (1994) Aerated Mixing of Viscoelasticfluidswith Helical Ribbon Impellers Experimental apparatus Vessel and impeller geometries Type: flat-bottomed Dimensions: D/d=hll w/d=0,133 p/d=0.695 /j/J=1.05 Working fluids and their physical properties Liquid: Rheological properties of test fluids n Test fluids
(-)
Glycerol 2.5% xanthan (H2O) 0.5%xanthan(H2O) 3%CMC(H20) 1%CMC(H20) 0.5% xanthan (glycerol/H2O) 800 ppm PAA (com syrup) 0.5% PIB (FB+kerosene)
1 0.183 0.250 0.299 0.409 0.199 0.94 1
m (Pas")
h (s)
lo (Pas)
7.83 0.110
469 1.57
ris
n'
(Pas)
(-)
in' (Pas")
0.19
0.782 1.67 2.00
7.85 0.15 1.29
0470 22.4 1.84
4.13 1.03 8.19
Notes: n, w, parameters in the power law model: 7;=my"; /i, rjo, parameters in Cross model: 77=770/1+(fiy)*~''; 77,, parameter in the expression: 77=mx"+77,;«', m', parameters in the expression: Ni-m'/y"', Gas: air
Results Np = P/d^N^p Laminar flow regime, 0.28 ^ Rea ^ 70 (0.028 <.Na<. 0.87,0.0044 ^ Wi < 0.060): Np = 1030i?e.-°-^Wfl^«»* (1 + 724 Fr«2.i5) Transition flow regime, 70 <. Rea <> 2600 (0.0087 <,Na^ 0.63,0.013 ^ Wi <, 0.96): Np = 40.3i?««-°-^iVfl«-^(l + 3.79 F^f«-*«0
Notation d impeller diameter, m D vessel inner diameter, m h height of liquid in vessel, m ks effective syear rate constant N impeller rotational speed, 1/sec Na aeration number, Q/Nd^, dimensionless Np power number, P/d^N^p, dimensionless p impeller pitch, m P power, W 0 flow rate, mVsec Rea aerated Reynolds number calculatedfromaerated deformation rate, % t\ Cross model parameter, sec Vg w
gas superficial velocity, m / s e c impeller width, m
3.2 MuKi phm99
Wi Ya Yb Ye T]a r]s p V^i
225
Weissenberg number, \if\Nlr]a, dimensionless aerated e£fective deformation rate eq (1), 1 / s e c additional deformation rate due to bubble passing, eq (2), 1 / s e c effective shear rate due to mechanical agitation, eq (3), 1 / s e c aerated effective viscosity, Pasec solvent viscosity, Pasec hquid density, kg/m^ primary normal stress difference coefficient, Pasec^
Ya = W^e
(1)
76 = 15001;^
(2)
Ye^ksN
(3)
226
Chapter 3. Power draw and consumption
Linek, V, Moucha, T. and Sinkule, J., Chem. Eng. Sci., 51,3203 (1996) Gas-Liquid Mass Transfer in Vessels Stirred with Multiple Impellers-I. Gas-Liquid Mass Transfer Characteristics in Individual Stages Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.19 m Liquid contained Height: (1) IT(2)2T(3)3T (4) 4 T Volume of liquid in vessel: (1) 0.00517 (2) 0.00517 x 2 (3) 0.00517 x 3 (4) 0.00517 x 4 m^ Baffle Number: 4 Width: 0.019 m Impeller Type: a standard Rushton turbine Diameter 7/3 Number of impeUers: (1) 1 (2) 2 (3) 3 (4) 4 Number of blades on impeller: (1)~(4) 6 Length and width of impeller blade: D:L:w:b = 20:5: A: 15 Positions of impellers: Distance between bottom andfirstimpeller: D Distance betweenfirstand second impeller: T Distance between second and third impeller: T Distance between third and forth impeller T Sparger Location: underneath thefirstimpeller Working fluids Liquid: distilled water and 0.5 M Na2S04 solution Gas: air, nitrogen and pure oxygen Experimental conditions Superficial gas velocity: 2.12,4.24 and 8.48 nun/sec Agitator speed: 5.5—18.8 1/sec Temperature: 20°C Results For water («iW = 0.0377 7V^^Sr°-^^ (e2-^4)agit = 0.104
N^'^Vs-''^
For0.5MNa2SO4 (ei)agit = 0.177 N^Vs-'''^ fe~4W = 0.090 i\r3-oit;,-«-359
Notation b diameter of agitator disk, m D diameter of agitator, m {^dagit power input by agitator per unit volume of liquid in\ stage i,W/m3 L length of blade, m N agitator speed, 1/sec T diameter of vessel, m superficial gas velocity, m/sec Vs w width of blade, m
3.2 Multi phase
227
Mochizuki, M., Takei, N., Sato, T, Tada, H., Sato, K. and Akehata, T, Kagaku Kogaku Ronbunshu, 23,342 (1997) Power Required for Upper Impeller in Gas-Liquid Vessels Agitated by Dual Turbines with Various Designs Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.3 m Liquid contained Height: 0.6 m Baffle Number: 4 Width: 0.03 m Impeller (2) flat six-blade disk turbine 0.100 (S) 0.125 (M) 0.025 0.02 (1)
Type Diameter (m) Impeller width (m)
(3) 0.15 (L) 0.030
hzim)
0.05-0.30
0.05-0.30
0.05-0.30
hiim)
0.075
0.075
0.075
Working fluids Liquid: tap water Gas: air
Experimental conditions
Airflowrate: 8.3 x 10-^-7.5 x 10"* mVsec (20°C, 1 atm) Rotational speed of impeller: 150—500 1/min Results
tl-'-'"' g 7 = 0.55
JK^T)
4 dr—d
Chapter 3. Pow«r draw and consumption
228
I
(a)
L Type 1 J
hj-dOcm n«500min'' d-IOcm I—I i i _ j I i 1-
S:I M,L:DI L
Type II
1*1
I
ha-Scm n-350min-' d«10an U. I I I I
Dual impeller ^ Upper Lower "" Single impeller ]
E^ ^
•
Type lit I
0.5 h
I
Lin
\ \S:nY \ y.L^A "
S,M:n
_•.
o4 «. -J
S.M: I
j
1 1 1—I—I
\
^
h2-25cm n-300mln-' d»15cm H L—J
'
«
«
5 NAXIO*
«
'
I
I
I
10 H
Type I, II and HI of {Pg/Po)-NA curves for dual disk turbins.
0.5
IWdrH Map of Type I, II and III of (P^/Po)~^k curves for dual disk turbins (A^^^O.ll). S,rf= 0.10 m; M,rf= 0.125 m;L,rf = 0.15 m.
Type I: a region where the power reduction (1 - (Pg/Po)) (PR) of the lower impeller is ahnost equal to that of the single impeller and the PR of the upper impeller is always less than that of the lower impeller under the same experimental conditions and the PR of the upper impeller is always less than that of the lower impeller. Tjrpe II: a region where the above-shown relationship between the PR of the lower impeller and the upper impeller is reversed by increasing the gas flow rate. Type III: a region where the PR of the upper impeller is almost equal to that of the lower impeller. Notation d impeller diameter, m dr vessel diameter, m Fr Froude number, n^d/g, dimensionless acceleration of gravity, m/sec^ g hi bottom clearance of lower impeller, m fe impeller spacing, m n rotational speed of impeller, 1/sec NA gas flow number, Qglnd^, dimensionless agitation power input, W P Q. gas flow rate, mVsec Subscripts 0 unaerated aerated g U upper impeller
3.2 MuKiphaM
229
Birch, D. and Ahmed, N., Ttans. Instn. Chem. Engrs., 75, P ^ A, 487 (1997) The Influence of Sparger Design and Location of Gas Dispersion in Stirred Vessels Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.6 m Liquid contained Height: 0.6 m Baffle Number: 4 Impeller Type: (1) FDT (Rushton turbine) (2) PDD (downward pumping 45° six bladed pitched blade disc turbine (3) PDU (upward pumping 45° six bladed pitched blade disc turbine
FDT
Z) = 0.200m w = D/4 q = D/5 r = 3w/5 a = 45°
PDT
Details of the impeller geometry. Off-bottom clearance: (1) (2) 0.2 m
Chapt«r 3. Pow«r draw and consumption
230
Sparger
u9
RiHtla Rinfla RintSa ie RiHx3l o Rmt4a !•» Foint
RingJb 1 m Rint2b • RiniSh o Rinjt4l • Rint4b
A,
Ring Spai]gers Q_
O
Ringl -» Rmg4
o A
r-'nr
is:
*?i:if±r:a
•TI'T -LZ) .}
)
TI
-Sr" S
)
point Spuger
£1
h-135 H
h
200 290 400 T = 600
H
Schematic of the sparger size and location with respect to the impeller position. Impeller diameter is 200 mm. (Note: the nomenclature a, b, I in italics refer to positions above, below and level to the impeller plane, respectively).
Results
(a) Aerated power conswnption and (b) the gas holdup as a function of the flow number for spaiging arrangements placed below the impeller with the Rushton impeller (FDT), at a stirrer speed of 6.1 s"^
(a) Aerated power consumption and (b) the gas holdup as a function of theflownumber for sparging arrangements placed level with the impeller for the Rushton impeller (FDT), at a stirrer speed of 6.1 s'K
3.2 MultiphaM
231
OM
• o«o «|S^
*
1 «*«»
PIHMS N.6.IA
MW3« 1 Wnim
01
an
014
01*
oii
How MMMber. Q ^ N D ' «kg<« o 0 fate t ^ N-6.IA 0
M
J*
i: s '
. y < ^ ^
^T^*!]!------*
b
Jtf^\
4
1
A'
0
Om
\— OM
1 006
1 —— 1 — 1 — 1 — ^ OM
ai
&12
014
OM
1 oil
Flow B m b e r , Q/ND*
(a) Aerated power consumption and (b) the gas holdup as a function of the flow number for sparging arrangements placed below the impeller with the pitched blade disc impeller pumping upward (PDU), at a stirrer speed of 6.1 s"*. The dotted lines indicate the point of the flooding transition.
vS?
(a) Aerated power consumption and (b) the gas holdup as a function of the flow number for sparging arrangements placed above the impeller with the pitched blade disc impeller pumping upward (PDU), at a stirrer speed of 6.1 s~*. The dotted lines indicate the point of the flooding transition.
roms
(a) Aerated power consumption and (b) the gas holdup as a function of the flow number for spaiging arrangements placed below the impeller with the pitched blade disc impeller pumping downward (FDD), at a stirrer speed of 6.1 s~^ The dotted lines indicate the point of thefloodingtransition.
(a) Aerated power consumption and (b) the gas holdup as a function of theflownumber for spaiging arrangements placed above the impeller with the pitched blade disc impeller pumping downward (FDD), at a stirrer speed of 6.1 s"*. The dotted lines indicate the point of thefloodingtransition.
232
Notation D impeller diameter, m N impeller speed, 1/sec Pg power draw, gassed liquid, W Pu power draw, ungassed liquid, W Q volumetric gas flow rate, mVsec e gas holdup
Chapter 3. Pow«r draw and consumption
3.2 Multiphase
233
3.2.3 Solid-liquid-gas systems Koloini, T, Plazl, I. and Zumer, M., Chem. Eng. Res. Des., 67,526 (1989) Power Consumption, Gas Hold-up and Interfacial Area in Aerated Non-Newtonian Suspensions in Stirred Tanks of Square Cross-Section Experimental apparatus Vessel geometries and experimental conditions Type:flat-bottomedvessel of square cross-section SQT-0.3
variable
SQT-0.7
0.3 m 0.33 m standard six blade Rushton 0.1m 0.11m 0.03 m^ tube underneath of stirrer 0.0058-'0.027 200-800 30-1,600 1,050-1,230 3-100 20 or 30
side length suspension depth stirrer type stirrer diameter clearance from bottom suspension volume sparger type sparger location VG m/sec N 1/min P/V W/m^ PL kg/m^ j]ef mPasec T °C
0.7 m 0.82 m 0.267 m 0.21m 0.4 m' tube underneath of stirrer 0.02-0.08 100-500 30-2,250 1,050-1,160 1.9-12 20 or 30
Workingfluids,solids and their physical properties Fluids: Suspensions of CaCOa and Ca(0H)2 Rheological properties of CaCOa and Ca(0H)2 suspensions at 20°C Cone. (wt. %)
/ir(Pas«)
n(-)
0.025 0.14
0.6
CaCOs
10 15 25
2.1
0.45 0.22
Ca(0H)2
5 10 15 20
0.0035 0.037 0.33
1.1
0.87 0.54 0.28 0.23
Gass: air+COa for SQT-0.3 andfluegas for SQT-0.7
Chapter 3. Pow«r draw and consumption
234
Results Power consumption ForSQT-0.3 0^
P = 1.5
PSND^' /^0.56
Notation D impeller diameter, m K fluid constancy index, Pasec" n fluid behavior index N stirrer speed, 1/sec P stirrer power input in gassed suspension, W PQ stirrer power input in ungassed suspension, W QG gasflowrate, mVsec VG superficial gas velocity, m/sec V suspension volume, m^ 77^ effective viscosity, Pasec PL suspen sion density, kg/m^
3.2 Multiphas*
235
Satoh, K., Shimada, H. and Yoshino, Z., Kagaku Kogaku Ronbunshu, 17,937 (1991) Power Requirements of Gas-Liquid Contactors with Mechanical Agitation Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.1,0.21,0.29 and 0.40 m Liquid contained Height: D under ungassed conditions Baffle Number: 4 Width: 0.1 Z) Impeller Type
Sign.
Diameter of impeller
Wide of blades
Length of blades
Angle of blades
Number of blades
(-)
dim)
b/di-)
l/d{-)
(degree)
1/5
1/4
90
Flat Blade Disk Turbine
6DT
0.08 0.10 0.12 0.15
Modified Disk Turbine-1
6MDT-1
0.08 0.10 0.15
V2/5
1/4
+45 -45
6
Modified Disk Turbine-2
6MDT-2
0.08 0.10 0.12 0.15
(>f2+l)/10
1/4
+45 -90
6
Pitched Blade Disk Turbine
6PBDT
0.10
V2/5
1/4
45
6
6PBT
0.08 0.10 0.15
1/5
1/2
45
6
Pitched Blade Turbine
Off-bottom clearance: H/b Sparger Type: 20 hole nozzle Nozzle diameter: 8 mm Nozzle height: 26 mm Hole diameter: 1 mm Location: directly below the impeller Working fluids, solids and their physical properties Liquid: tap water Solid: glass spheres density = 2.52 g/cm^; average particle diameter = 70 fim kaohn density = 2.55 g/cm^; average particle diameter = 5 pm Gas: air
Chapter 3. Power draw and consumption
236 Results
—-"(ir(fm Values of a and p for various impellers Impeller
6DT
6MDT.1
axlO-^OV/m^)
8.38 1.33
9.90 1.19
(-)
P r^
6 MDT-2 radial
down
8.38
7.30 1.26
• 6PBDT 4.50 1.32
= K
{Pav)c
K = 3.0 for all impellers Notation h width of impeller blade, m diameter of impeller, m d diameter of vessel, m D Do diameter of standard vessel, m Fr Froude number for agitation, N^d/g, dimensionless acceleration of gravity, m/sec^ g liquid depth in vessel without aeration, m H length of impeller blade, m I rotation speed of impeller, 1/sec N aeration power input per unit volume of liquid, W/m^ agitation power input to gassed liquid per unit volume of liquid, W/m^ PaV density of suspension, kg/m^ density of water, kg/m^ P Subscript c values at the critical point
6PBT 3.40
3.2 Multiphas«
237
Satoh, K. and Shimada, H., Kagaku Kogaku Ronbunshu, 19,557 (1993) Power of Impeller Required for Complete Off-bottom Suspension of Solid Particles under Gassing Conditions Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.29 m Liquid contained Height: 0.29 m Baffle Number: 4 Width: 0.029 m Impeller Type
Modified Disk Turbine-1
Modified Disk Turbine-1
Pitched Blade Disk Turbine
Sign.
Diameter oi• Wide of blades impeller d{m) b/d{-)
Length of blades
l/d(-)
Angle of blades (degree)
Number of blades
d(-)
6 MDT-1
0.08 0.10 0.12 0.15
V2/5
1/4
+ 45 -45
6
6 MDT-2
0.08 0.10 0.12 0.15
(V2"+1)/5
1/4
+ 45 -90
6
6 PBDT
0.08 0.10 0.12 0.15
^2/5
1/4
45
6
I > ^ = ^ Q-^F€^ ^^2r^^^ 6M0T-1
6MOr-2
6 PBDT
Off bottom clearance: HIb Sparger Type: 20 hole nozzle Nozzle diameter: 8 mm Nozzle height: 26 nun Hole diameter: 1 nun Location: directly below the impeller Working fluids, solids and their physical properties Liquid: tap water SoUd: glass spheres (density = 2.52 g/cm^; average particle diameter = 72.3,116.9,203.5 and 480.3 \m) Gas: air
238
Results {Rv)c=a(Frr\^
DJ
[Doj [pw
Values of a and P for various impellers 6MDT-1
Impeller axlO-^OV/m^)
9.90
P(-)
1.19
rav
6MDT-2 radial
down
8.38
7.30 1.26
APRTlT OrDU I
4.50 1.32
(Pav)c
K = 3.0 for all impellers
Notation b d D Do Fr g H / N Pav Pgv T p pw
width of impeller blade, m diameter of impeller, m diameter of vessels, m diameter of standard vessel, m Froude number for agitation, N^d/g, dimensionless acceleration of gravity, m/sec^ liquid depth in vessel without aeration, m length of impeller blade, m rotation speed of impeller, 1/sec aeration power input per unit volume of hquid, W/m^ agitation power input to gassed liquid per unit volume of liquid, W/m^ tank diameter, m density of suspension, kg/m^ density of water, kg/m^
Subscript c values at the critical point
239
Chapter 4.
Heat transfer
4.1 Single phase Mizushina, T, Ito, R., Murakami, Y. and Kiri, M., Kagaku Kogaku, 30,719 (1966) Experimental Study of the Heat Transfer of Newtonian Fluid to the Wall of Agitated Vessel Experimental apparatus Vessel Type: flat-bottomed Diameter: 29.6 cm Height: 45.0 cm Liquid Height: 38.0 cm Baffle Number: 4 Width: 1.6 cm Impeller Type
anchor 18,25 — 25,28 90 2
Diameter (cm) Width (cm) Arm height (cm) Angle of blade (°) Off-bottom clearance (cm)
paddle
propeller
18 3.0 — 90 6,26
18 3.0 — 45 6,17
Working fluids Newtonian fluids Experimental conditions Re number: Anchor: 2.13 x 10^ ~ 1.18 x 10^ Paddle: 1.35 x 10^ - 5.48 x 10* Propeller: 9.82 x 10^ ~ 9.17 x 10* Results For wall-side heat transfer coefficient X •
\l/3/
x0.15
felW r
• = 0.46
f
0.63
^sin^n^ H
UN V
240
Chapter 4. H«at tninster
For power consumption
m \l/3/
0.14 /
5
X 0.1 /
j
\^^^
2r--
V"
= 0.551 £ ii^^ ^ . \0.15 f f , . \\ * ^ ( « , r 1-0.211 0 . 6 3 - ^ ^ ^ H ^ "'
Notation ft impeller width, cm Cp specific heat of liquid, cal/g°C D vessel diameter, cm H height of heat transfer surface, cm hj heat transfer coefficient on the inside wall of agitated vessel, cal/cm^sec°C L impeller diameter, cm N impeller speed, 1/sec Npf power number in fiilly bafiled condition, dimensionless tip number of impeller blades Pgc power consumption of impeller, dynecm/sec w anchor arm width, cm Q angle oi blades to the horizontal plane, degree A thermal conductivity of liquid, cal/seccm°C \i viscosity of liquid, g/cmsec V kinematic viscosity of liquid, cmVsec p density of liquid, g/cm^ Subscripts b bulk temperature w wall temperature
4.1 SingI* phas«
241
Mizushina, T, Ito, R., Murakami, Y. and Tanaka, S., Kagaku Kogaku, 30,819 (1966) Experimental Study of the Heat Transfer of Non-Newtonian Fluids to the Wall of Agitated Vessel Experimental apparatus Vessel Type: dish-bottomed Diameter: 296 mm Height: 380 mm Liquid contained Height: 340 mm Impeller Type: (1)~(4) anchor Diameter: (1) 250 (2) 180 (3) 250 (4) 250 mm Number of impellers: 1 Number of blades on impeller: (1)^(4) 2 Height of anchor arm (paraUel to shaft): (1) 280 (2) 280 (3) 220 (4) 280 mm Width of anchor arm (perpendicular to shaft): (1) 25 (2) 35 (3) 25 (4) 35 mm Off-bottom clearance: (1)~(4) 40 mm Working fluids and their physical properties For pseudoplastic fluids Unit mm
-h.
lffi=
1 |8
•^.~ 185
mm
is,
145
1 ..> 250 -
-
35
—-rt
•HH
fc
\LJl
•
Chapter 4. H«at tninster
242
Fluid in jacket: water Fluid in tank: aqueous solutions of CMC and polyethylene-toluene solution Solution n 0.5% CMC-water solution 1.0 2.0% CMC-water solution 0.65-0.82 2.5% CMC-water solution 0.59-0.67 3.0% CMC-water solution 0.57-0.65 3.5% CMC-water solution 0.51-0.58 4.0% CMC-water solution 0.44-0.55 25% polystyrene-toluene solution 0.85-0.95 For plastic fluids Fluid in jacket: water Fluid in tank: cement slurry Concentration
So
A
Cp
P
Sample
(wt%)
(Vol%)
(dyne/cm^)
(kcal/mhr°C)
(kcal/kg°C)
(g/cm^)
S-2 S-3 S-4 S-5 S-6 S-7
54.0 49.4 55.3 56.8 50.4 48.1
28.1 25.5 29.8 31.0 26.0 24.5
25.1 10.6 36.6 53.1 13.03 7.24
0.721 0.704 0.733 0.741 0.705 0.707
0.56 0.61 0.57 0.56 0.61 0.62
1.56 1.47 1.57 1.60 1.51 1.47
Results For the pseudoplastic fluids
M=o.4£^ A
1 /x«
A J t//o
//« and //o are obtained from To
T =
-r+^l-r
l^fl + 7
'VNp^ For the plastic fluids
""•fel
Nu\^ Vb J Pr1/3
±L
1/3
1+ rib
OARe' 1/3 l+4MxlO^He0.lPr'"Re
r,^-6/6
4.1 Single phase
Notation a Cp D He hj h* / L -A^ Nu Nu* Re Pr SQ 7] A fi p T
constant, 1/sec specific heat of liquid, c a l / g ° C vessel diameter, cm Hedstrom number, L^Sop/rjbf dimensionless heat transfer coefficient based on the inside waD of agitated vessel, cal/cm^sec°C heat transfer coefficient between stagnant layer and agitated liquid, cal/cm^sec'^C thickness of stagnant layer, cm impeller diameter, cm impeller speed, 1/sec Nusselt number, hjD/k, dimensionless Nusselt number, /j'D/A, dimensionless Reynolds number, DNp/^ib, dimensionless Prandtl number, Cp ^blK dimensionless yield value, dyne/cm^ plastic viscosity, g/cmsec thermal conductivity of fluid, cal/seccm°C viscosity of fluid, g/cmsec density of fluid, g/cm^ shear stress, dyne/cm^
Subscripts b bulk temperature w wall temperature
243
Chapter 4. Heat transfer
244
Mizushina, T, Ito, R., Murakami, Y. and Kiri, Y, Kagaku Kogaku, 30,827 (1966) Experimental Study of the Heat Transfer to the Cooling Coil in an Agitated Vessel Experimental apparatus Vessel Type: flat-bottomed Diameter: 29.6 cm Height: 45.0 cm Liquid contained Height: 38.0 cm Baffle Number: 4 Width: 1.6 cm Impeller For Newtonian fluids Type Diameter (cm) Width (cm) Arm height (cm) Arm width (cm) Number of blades Angle of blade (°) Off-bottom clearance (cm) For Non-Newtonian fluids Type Diameter (cm) Impeller width (cm) Arm height (cm) Arm width (cm) Number of blades Angle of blade (°) Off-bottom clearance (cm)
paddle
anchor
turbine
5,10,12,13,18 2.6,3 — — 2,4 45,90 4,10,17,26,27
12,18 — 18 1.7 2 90 10
12,18 2.6,3.6 — — 4 90 4,10,17
anchor 12,18,18.3 — 18 1.5 2 90 10
turbine 18 3.6 — — 4 90 10
4.1 Single phase
245
Cooling coil For Newtonian and non-Newtonian fluids 0.777, 1.03 0.76 0.0405,0.0541 0.0467,0.0487 0.135
HcID Dr/D dcID dgID
dJD
coil
dc
d,
Dc
He
cooling area based on the outside dia.
A B
1.2 1.6
1.37 1.44
22.5
23.0 30.5
0.281 (m^) 0.414 (m^)
(A)
(B)
246
Chapter 4. H«at transfer
Working fluids Newtonian fluid: water, water-glycerin solution and caster oil Non-Newtonian fluid: carboxy methyl cellulose and cementrock slurry Results For Newtonian fluids 0.15
^
>^1.7^
>^0.14
^''^'^23Re'^'Pr'^(^^'^^^ 3xl0^>/?e>10l
when
He
^0.32,
"'^^
Hr
' = 0.32
For non-Newtonian fluids /
A
N0.15
y He J
^
N1.7X
X0.14
\^^ J v^O
a-e'""-) p^^_c,m,a-e-"^r'N"-' fl = 1.42x10"' 10S/?r>0.2,
1>«>0.53. when f ^ l > 0 . 3 2 , f ^ l = 0.32
Notation a constant, 1/sec b impeller width or anchor arm height, cm Cp specific heat of liquid, c a l / g ° C dc cooling pipe diameter shown in figure, cm Dc cooling coil diameter shown in figure, cm he heat transfer coefficient based on outside wall of cooling coil, cal/cm^sec-°C He height of cooling coil shown in figure, cm L impeller diameter, cm m constant of power law equation, dynesec"/cm^ n constant of power law equation, dimensionless Up number of blade N impeller speed, 1/sec Re Reynolds number, L^Np/^b, dimensionless Re** modified Reynolds number, dimensionless Pr Prandtl number, Cp^blK dimensionless Pr* modified Prandtl number, dimensionless w anchor arm width, cm 0 angle of blade to the horizontal plane, degree A thermal conductivity of liquid, cal/seccm°C /z viscosity of liquid, g/cmsec p density of hquid, g/cm^ 0(n) function of n Subscripts h value evaluated at buld temperature c value evaluated at coil temperature
4.1 SingI* phase
247
Coyle, C. K., Hirschland, H. E., Michel., B. J. and Oldshue, J. Y., Can. J. of Chem. Eng., 48,275 (1970) Heat Transfer to Jackets with Close Clearance Impellers in Viscous Materials Experimental apparatus Vessel and impeller geometries Vessel Diameter (m) Helicalribbonimpeller Diameter (in) Pitch (based on the impeller diameter) Off-bottom clearance (in) Liquid level
14
30
13 0.5 1/2 14
29 0.5 1/2 30
Cooling device Type: jacket Cooling liquid: water Workingfluidsand thir physical properties Organic materials with pseudoplastic characteristics Thermal conductivity: 0.08-0.09 Btu/hrT/ftVft Results 14-in. dia. tank, 13-in. diameter helical impeller N rpm
Viscosity at shear rate 5 sec:\ 100°F
Viscosity Power law exponent, n
h Btu/hr *^F/sq.ft
7 10 18 20 25 50
100,000 2,000 100,000 2,000 30,000 30,000
0.2 0.8 0.2 0.8 1.0 1.0
3.7 4.5 4.2 3.6 4.0 5.0
30-in. dia. tank, 29-in.
Viscosity at shear rate 5 secrS 100°F
Viscosity Power law exponent, n
h Btu/hr °F/sq.ft
6 6 12 18 18 49
30,000 100,000 30,000 30,000 100,000 100,000
0.8 0.2 0.8 0.8 0.2 0.2
4.6 4.0 5.5 5.7 4.5 2.0
Notation h
heat transfer coefficient, Btu/hr^F/ft^
Chapter 4. H«at tninsfor
248
Nagata, S., Nishikawa, M., Takimoto, T, Kida, E and Kayama, T., Kagaku Kogaku, 35,924 (1971) Jacket Side Heat Transfer Coefficient in Mixing Vessel Experimental apparatus Vessel Type: (1) dish-bottomed (2) flat-bottomed
Baffle Number: unbailed or 4 Width: Z)/10
Impeller type and geometries Impeller
d(cm)
turbine for vessel (1) 7.5,10,15,20 4.2,6.8,8.2,10,10.3 paddle 11,12.2,15,18.5 turbine for vessel (3) 10,15,20
/(cm)
np
1.875,2.5,3.75,5
2,4,6,8,16 16,6,4,3,2
90°, 60°, 45° 90°, 60°, 45°, 30°
rf»=lcm
6
90°
Working fluids and their physical properties
pitched paddle
turbine Fluid in jacket: steam Fluid in vessel: tap water, glycerin and CMC solution Physical properties at 20°C
P (kg/m^) water glycerin CMC solution
1,000 1,200 1,000
essel (2) Fluid in jacket: steam Fluid in vessel: tap water
9
bicm) 1,1.5,2,3,4,6 1,1.5,2,3,6,4.2 6.8,11 2,3,4,6
Cp
k
(kcal/kg.^'C) (kcal/mhrX) 1.0 0.70 1.0
0.512 0.25 0.512
M (poise) 0.01 10.0 0.03-7
4.1 Singl« phas«
Results Without baffles
249
Re > 100 and 2
2,000
(hjD/k) = a {d'np/fir\Cp^i/kf\nJtir''''
(d/Dy'^'inpr'
v0.15
J^Ci/m]
(smdf^(H/D)'
without coils a = 0.51 a = 0.54 with coils With baffles (hjD/k) =
i?^ >100 lAO(d'np/^)''\Cp^/kf\fiJ^y'''* /
\0.45
/
\0.2
Notation b width of impeller blade, cm c impeller height, cm Cp specific heat of fluid, kcal/kg°C d impeller diameter, cm dn diameter of coohng water spout, cm D vessel diameter, cm hj heat transfer coefficient on the inside wall of agitated vessel, kcal/m^hr°C H hquid height in mixing vessel, cm i number of impellers k thermal conductivity of fluid, kcal/mhr°C n impeller rotational speed, 1/sec Hp number of impeller blades 6 angle of impeller blade, degree /z viscosity of bulk fluid, k g / m h r ^«, viscosity of liquid at wall temperature, k g / m h r p density of fluid, kg/w?
250
Chapter 4. H«at trainsffar
Nagata, S., Nishikawa, M. and Takimoto, T, Kagaku Kogaku, 35,1028 (1971) Heat Transfer to Helical Coils Immersed in Mixing Vessel Experimental apparatus Vessel Type: dished-bottomed Diameter: 30 cm Liquid contained Height: 40 cm Baffle Number: unbaffled or 4 Width: Z)/10 Impeller Experiment I Type: turbine Number of impeUers: 1 Geometries: d/D = 0.33 h/D = 0.03'-'0.2 np = 2-16 C//f= 0.13-0.6 sin0 = 0.5-1 Experiment H Type: six blade turbine (^=90°) d/D 0.5 0.33 Cooling coil No. 1 2 3 4 5
b/D 0.1 0.067
CdH 0.5 0.5-0.625
C2lH 0.125-0.48 0.125-0.48
dgixam) 10 15 20 15 15
Z)r (mm) 225 225 225 210 240
ft (mm) 80 80 80 80 80
Lf (mm)
230 230 230 230 230
Working fluids and their physical properties Fluid in coil: water Fluid in tank: tap water, glycerin and CMC solution Physical properties at 20*^0^ P (kg/m^) water glycerin CMC solution
1,000 1,200 1,000
Cp
k
(kcal/kg°C) (kcal/mhr-^C) 1.0 0.70 1.0
0.512 0.25 0.512
A' (poise) 0.01 10.0 0.03-7
4k1 Singi« phas*
251
Results (1) Impellers are pkiced inside of cooling coils
(2) Impellers are placed outside of cooling coils (without baffles)
(3) Impellers are placed outside of cooling coils (without baffles) Nuc=2mRe'^Pr'^^Vis-''\d/Dr'^{ib/Df\npr
[j^dliH]
(smGfHH/Dy'^
Notation b impeller width, cm C impeller height, cm Cp specific heat of fluid, kcal/kg-°C d impeller diameter, cm dco outside diameter of coil tube, cm dg clearance between individual turn of coohng coil, mm D vessel diameter, cm Dc coil loop diameter, cm ha, heat transfer coefficient at outer surface of cooling coil, kcal/m^hr°C H liquid height in mixing vessel, cm He lowest coil level, nmi i number of impellers k thermal conductivity, kcal/mhr*'C Lc overall hight of cooling coil, nrni n impeller speed, 1/sec ftp number of impeller blades Nuc Nusselt number (coil side), heoD/k, dimensionless Re agitation Reynolds number, d^np/fi, dimensionless Pr Prandtl number Cp ji/k, dimensionless Vis viscosity index, ^w/^, dimensionless 0 angle of impeller blade, degree p hquid density, kg/m^ ^ viscosity of bulk hquid, poise fiw viscosity of liquid at wall temperature, poise
Chapter 4. H«at transter
252
Edney, H. G. S. and Edwards, M. E, Trans. Instn. Chem. Engrs., 54,160 (1976) Heat Transfer to Non-Newtonian and Aerated Fluids in Stirred Tanks Experimental apparatus Vessel Type: flat-bottomed Diameter 1.22 m Height: 1.22 m Liquid contained Height: 0.92 m Baffle Number: 4 Width: 0.0637 m Impeller Type: six-flat-bladed disc turbine Diameter: 0.305 m Number of impellers: 1 Number of blades on impeller: 6 Width of impeller blade (parallel to shaft): 0.061 m Cooler Mean helix diameter: (1) 0.559 (2) 0.762 (3) 0.955 m Coil internal diameter: 0.041 m Coil external diameter: 0.047 m Working fluids Fluid in cooling coil: water Fluid in tank: non-Newtonian fluids: various dilute solutions of sodium carboxymethyl cellulose and polyacryl amide Experimental conditions 4.01 X 102
'v - 0 3 7 5
iVM = 0.036i?erW-^' Dc\ [DT\
r
-i 0 2
f//J \^A.\
Notation Cp dc D Dc DT he k N
specific heat of agitated liquid outside diameter of coil tubing impeUer diameter mean helix diameter tank diameter process side heat transfer coefficient for coil thermal conductivity of process liquid rotational speed of im][)eller
Nu Rei Pri MA t^Au,
Nusselt number, hcddk, dimensionless modified Reynolds number, pND^I^Af dimensionless modified Prandtl number /i^ Cplk, dimensionless average apparent viscosity average apparent viscosity at mean temperature of heat transfer surface
4.1 Single phas«
253
Sano, Y., Usui, H., Nishimura, T. and Saito, E., Kagaku Kogaku Ronbunshu, 4, 159 (1978) Correlation of Heat Transfer CoefiBcient at the Wall of Mixing Vessel Experimental apparatus Vessel and cooling coil geometries System Vessel Type Diameter (cm) Height (cm) Baffle Number Liquid contained Height (cm) Cooling coil Outside diameter of tube (nmi) Diameter of coil (cm)
(1)
(2)
flat-bottomed 10 10
flat-bottomed 19 20
4-'12
4--12
10
19
6 6
12 12
Impeller System Type d/D b/D tip
e
(2)
(1)
paddle 0.33,0.4,0.5,0.6,0.7,0.8,0.9 0.1,0.2,0.5 2,6 30^ 60°, 90°
paddle 0.33,0.4,0.5 0.1,0.2,0.5 2 90°
IB/D
I
l|l
A
\^
h
turbine 0.5 0.1 6 90° 0.12
C ^ ^
paddle
pitched paddle
turbine
Impeller Working fluids and their physical properties Liquids: water and aqueous solutions of glycerin (viscosity = 0.55—8.5 cP) Experimental conditions Rotational speed of impeller 110—550 rpm Temperature of bulk liquid 25-40°C Difference of temperature between bulk liquid and wall 5~20°C Reynolds number 900-70,000 Prandtl number 5-70
Chapter 4. Heat transfer
254
Results hD = 0.512 eD
.a227
\052 x
l/3\d_]
Pr
>^0.08
[^
Notation b Cp d D h IB tip P Pr V e 6 A ^ V p
impeUer width, cm beat capacity of liquid, kcal/g°C impeUer diameter, cm vessel diameter, cm heat transfer coefficient, kcal/cm^hr°C blade length of turbine type, cm number of impeller blades power dissipated in mixing vessel, kgcmVsec^ Prandtl number, C^/x/A, dimensionless liquid volume in vessel, cm^ energy dissipation per unit mass, P/pv, cmVsec? angle of impeller blade, degree thermal conductivity, kcal/cmhr°C viscosity of bulk liquid, g/cmsec kinematic viscosity of liquid, cmVsec density of liquid, g/am?
4.1 Single ph«s«
255
De Maerteleire, E., Chem. Eng. ScL, 33,1107 (1978) Heat Transfer to a Helical Cooling Coil in Mechanically Agitated GasLiquid Dispersions Experimental apparatus Geometrical characteristics of experimental equipment 1. Heat transfer vessel — flat bottomed cylindrical glass jar wall thickness: 0.001 m height: 0.250 m diameter: 0.180 m liquid height in the vessel: 0.204 m depth gas distributor below hquid surface: 0.200 m depth impeller below hquid surface: 0.195 m. 2. Baffles — four baffles made of stainless steel thickness: 0.001 m width: 0.018 m placed 0.001 m jfrom the vessel waU at right angles. 3. Impeller — four bladed paddle impeller diameter: 0.100 m blade dimensions: thickness: 0.001 m width: 0.020 m length: 0.035 m blade angle: 45 deg. 4. Coil — helical cooling coil made of pure red copper height: 0.115 m number of turns: 5 clearance between two turns: 0.013 m outside diameter of coil tubing: 0.012 m inside diameter of coil tubing: 0.008 m inside diameter of hehx: 0.100 m.
Working fluids Liquid: distilled water, distilled water + a surface active agent, isopropyl alcohol, ethylene glycol and two mineral oils.
Experimental conditions Range of variables covered Impeller speed: 100 ~ 800 rpm Nusselt number 167 ~ 1,553 Reynolds number: 167 ~ 245,000 Prandtl number: 2.91 - 1,262 Viscosity ratio: 0.194 - 0.904
Results
256
Chapter 4. H«at transfer
Notation Cp specific heat of agitated liquid, kcal/kg°C Dr impeller diameter, m DT vessel diameter, m hu external coil heat transfer coefficient, kcal/secm^°C k thermal conductivity of process liquid, kcal/secm°C N rotational speed of impeller, 1/sec or rpm Nu Nusselt number, huDT/k, dimensionless Re Reynolds number, Dr^ yN/pt,, dimensionless Fr Prandtl number, Cp^ilk, dimensionless Vi viscosity ratio, ji/^wy dimensionless ^ dynamic viscosity of process liquid, kg/msec ^w dynamic viscosity of process liquid at temperature of coil surface, kg/msec 7 fluid density, kg/m^
4.1 Single phase
257
Bourne, J. R., Buerli, M. and Regenass, W, Chem. Eng. Sd., 36,347 (1981) Heat Transfer and Power Measurements in Stirred Tanks Using Heat Flow Calorimetry Experimental apparatus Bench-scale experiments Vessel
Diameter: 0.114 m Internal heat transfer surface: 0.04216 m^ hnpeller Type Diameter (mm) d/D
turbine 38 0.33
anchor 109.1 0.957
Pfaudler type
gate
67 a59
0.47
54
L73
h7d s/d
0.15
Full-scale experiments Vessel Type Working capacity (m^) Wall heat transfer surface (m^) Diameter (m) Impeller Type Diameter (m) d/D h'/d
dish-bottomed 2.5 6.93 1.59
s/d
anchor 1.52 0.957
dish-bottomed
5.4 14.4 1.95 gate 0.89 0.46
L79 0.16
' t 2.5 m^ steel tank with anchor impeller.
5.4 m^ glass-lined tank with gate impeller.
258
Chapter 4. Heat transfer
Working fluids Bench-scale experiments Fluid in jacket: low viscosity silicone oil Fluid in tank: toluene, isopropanol, ethylene glycol and glycerin Full-scale experiments Fluid in jacket: water Fluid in tank: ethylene glycol
Results (1) Turbine Nu=^QA2Re^^Pr^'^ (2) Anchor Nu^hQRe^'^Pr^^^Vi^'^' Nu = 0.29 /?^°-^^ Pr^'^ Ft°-^^
for i?« = 8-46,000 for Re<.10 for Re = 70'-600,000
(3) Pfaudler Nu = Q27Re^''Pr^'^
for i?g = 9-^55,000
(4) Gate Mt< = 0.55/?e°®/V^/'W°"
for i?« = 12'-300,000
Notation Cp heat capacity at constant pressure, J/kgK d diameter of impeller, m D diameter of tank, m h fihn heat transfer coefficient, W/m^K h height of impeller,m k thermal conductivity of fluid in tank, W/mK N impeller rotational speed, 1/sec Nu Nusselt number, hD/k, dimensionless Pr Prandtl number, /i Cplk, dimensionless Re Reynolds number, Nd V/M, dimensionless 5 width of anchor and gate blade, m Vi viscosity ratio, n/iiw, dimensionless ^ fluid viscosity, kg/msec ^w fluid viscosity at wall, kg/msec p density of fluid, kg/m^
4.1 Single phsM
259
Sano, Y., Usui, H. and Saito, E., Kagaku Kogaku Ronbunshu, 7,253 (1981) The Correlation of Heat Transfer Coefficient at Outside Surface of Helical Coil with Agitation Power Use of existing data Vessel diameter: up to 1.22 m Re = 10^-2 X10^ {edcMv^ = 10*~10^^) (/r./Z) = 0.063-0.018 HID=:l /
^ \ 0.205 X
\0t2>'
v0.1x
x-03
¥-«-^(^J [% [^ (t) '^•*'^Data used are shown below Oldshue, J. Y. and A. T. Gretton: Chenu Eng, Progr., 50,615 (1954) Nagata, S., M. Nishikawa and T. Takimoto: Kagaku Kogaku, 35,1028 (1971) Edney, H. G. S., M. F. Edwards and V. C. Marshall: Trans, Instn, Chem, Engrs,, 51,4 (1973) Sano, Y., H. Usui and E. Saito: Kagaku Kogaku Ronbunshu, 7,253 (1981)
Notation b Cp d dco D H hco n P Pr Re V Vis e A jLL fiw V p
impeller width, m specific heat, J/kgK impeller diameter, m outside diameter of coli tube, m vessel diameter, m liquid height in mixing vessel, m heat transfer coefficient at outer surface of coil, W/m^K rotational speed of impeller, 1/sec power dissipated in mixing vessel, kgmVsec^ Prandtl number, Q/z/A, dimensionless Reynolds number, d^n/v, dimensionless hquid volume in a vessel, m^ viscosity index, ^w//^, dimensionless energy dissipation per unit mass of hquid, P/pV, mVsec^ thermal conductivity of hquid, W/mK viscosity of bulk hquid, kg/msec viscosity of liquid at outside of coil wall, kg/msec kinematic viscosity of hquid, mVsec density of liquid, g/cm^
Chapter 4. Heat transfer
260
Sano, Y., Usui, H. and Saito, E., Kagaku Kogaku Ronbunshu, 7,253 (1981) The Correlation of Heat Transfer Coefficient at Outside Surface of Helical Coil with Agitation Power Experimental apparatus Vessel and cooling coil geometries System Vessel Type Diameter (cm) Baffle Number Width Cooling coil Outside diameter of tube (mm) Diameter of coil (cm) Pitch (mm)
(1)
(2)
flat-bottomed 10
flat-bottomed 19
4-8 0.05-0.13Z)
4-^8 0.0b-0.13D
6 6 12
12 12 24
Impeller Type d/D bID Hp
e Off-bottom clearance
paddle 0.33-0.5 0.1-0.5 2,6 90° H/2
turbine 0.5 0.1 6 90*^ H/2
pitched paddle 0.5 0.1-0.2 6 30°, 60°, 90° H/2
It
paddle
pitched paddle Impellers
Working fluids water and aqueous solutions of glycerin
d
turbine
J
4.1 Single phas«
261
Results 5.5 < /V < 96, 10' < (Erfi / v') < 10'°, 900
-(fm
^i2*L = o.755l^l W i - l [4Notation b impeller width, m Cp heat capacity of liquid, J / k g K d impeller diameter, m dco outside diameter of coli tube, m D vessel diameter, m hro heat transfer coefficient at outer surface of coil, W/m^K H liquid height in mixing vessel, m IB blade length of turbine type, m n rotational speed of impeller, 1/sec tip number of impeller blades P power dissipated in mixing vessel, kgmVsec^ Pr Prandtl number, Cp^/X, dimensionless Re Re3molds number, d^n/v, dimensionless V hquid volume in a vessel, cm^ Vis viscosity index, fiw/K dimensionless e energy dissipation per unit mass, P/pV, mVsec^ 0 angle of impeller blade, degree A thermal conductivity of liquid, W/mhrK /i viscosity of bulk liquid, kg/msec V kinematic viscosity of hquid, mVsec p density of liquid, kg/m^
Chapter 4. Heat transfer
262
Kuriyama, M., Ohta, M., Yanagawa, K., Aral, K. and Saito, S.,/. Chem. Eng. Japan, 14,323 (1981) Heat Transfer and Temperature Distributions in an Agitated Tank Equipped with Helical Ribbon Impeller Experimental apparatus Vessel and impeller geometries
D=L = 100 (mm) p= 90 (mm) w/D = 0.1 (-) c/D= 0.019 (-) 0.057 0.08A Working fluids and their physical properties Aqueous solutions of com symp viscosity = 1.4 kg/msec at 30°C heat capacity = 2.2 x 10^ J/kg°C themial conductivity = 0.36 J/msec*
Results Nu = OM RePr
(^j^r
Notation c Cp
d D h L n Nu P Pr Re w /i ^iw A p
clearance between blade tip and tank wall, m specific heat, J/kg-®C outside diameter of impeller, m inside diameter of tank, m heat transfer coefficient, J/m^sec**C height of vessel, m rotational speed of impeller, 1/sec Nusselt number, hD/X, dimensionless height of helical ribbon impeller, m Prandtl number, /x Cp/X, dimensionless Reynolds number, d^np/in, dimensionless width of heUcal ribbon impeller, m viscosity at bulk temperature, kg/msec viscosity at wall temperature, kg/msec themial conductivity of fluid, J/secm**C density of fluid, kg/m^
4.1 Single phas*
263
Kuriyama, M., Aral, K. and Saito, S.J. Chem. Eng. Japan, 16,489 (1983) Mechanism of Heat Transfer to Pseudoplastic Fluids in an Agitated Tank with Helical Ribbon Impeller Experimental apparatus Vessel and agitator geometries
0=L = l60(mm) ps 144 {mm) w/D = 0.1 (-) d,^0=QI (-) c/0s0.02A(-) 0.068 (-) 0.076 (-)
luid) ^Torque meter
Top view of bottom plate
lip ring L.—-Variable speed motor
Designs of agitated tank and impeller.
Working fluids 3% and 5% solutions of carboxymethyl cellulose (CMC) at 40°C K(N.s'"/m2) Cone (wt%) m 0.7 0.5
Results (
2
Nu
F = U+ £1=0.46
w = 0.5-1.0
£2=4
^'^
3 30
264
Notation c clearance between blade tip and tank wall, m Cp specific heat, J/kg°C d outside diameter of impeller, m D inside diameter of tank, m h heat transfer coefficient, J/m^sec°C K fluid consistency coefficient, Nsec"/m^ m flow behavior index n rotational speed of impeller, 1/sec Nu Nusselt number, hDl\ dimensionless p pitch of helical ribbon impeller, m Pr Prandtl number, \iCplK dimensionless Re Reynolds number, d^np/^y dimensionless £b £2 adjustable parameters jU viscosity at bulk temperature, k g / m s e c jUr viscosity correction factor, dimensionless ^w viscosity at wall temperature, k g / m s e c A thermal conductivity of fluid, J / s e c m ° C p density offluid,kg/m^
Chapter 4. H«at transfer
4.1 Single phase
265
Shamlou, R A. and Edwards, M. E, Chem. Eng. Sd., 41,1957 (1986) Heat Transfer to Viscous Newtonian and Non-Newtonian Fluids for Helical Ribbon Mixers Experimental apparatus Vessel Type Diameter (mm)
flat-bottomed 400
slightly dished-based 150
Impelle r Type: helical ribbon Dimensions: No.
T
D
w
P
p/D
w/D
cID
«6
hID
HIT
1 2 3 4 5 6 7 8 9 10
400 400 400 400 400 400 150 150 150 150
352 352 352 352 352 370 135 135 130 113
34 34 34 34 34 36 13 14 13 12
352 352 352 176 190 185 135 75 133 60
1 1 1 0.5 0.5 0.5 1 0.56 1.02 0.531
0.097 0.097 0.097 0.097 0.097 0.097 0.097 0.104 0.100 0.106
0.0682 0.0682 0.0682 0.0263 0.0263 0.0405 0.0556 0.0556 0.0769 0.1637
1 2 1 1 1 1 2 1 1 1
1.0 1.0 1.0 1.0 1.0 1.0 1.02 1.08 1.02 1.02
1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1 1.1
All measurements are in nrni.
Working fluids and their physical properties Thermal and physical properties of experimental fluids Fluid used
Density (kg/m^)
Specific heat (kJ/kg-K)
Thermal conductivity (W/mK)
Chocolate 7% CMC 3% CMC 1.5% CMC Glycerol
1,280 1,060 1,000 1,000 1,250
4.6at46°C 4.2 4.2 4.2 2.35at43^C
0.2118 at 46°C 0.595 at 45°C 0.600 at 45X 0.595 at 45°C 0.250 at 46°C
Lub. oil Silicone oil Sugar sol. 3% Carbopol 8% Biozam R
see Fig. 3 see Fig. 3 1,483 1,000 1,000
2.18at40°C
0.150 at 45°C
1.51at50X 2.5at50°C 4.2 4.2
0.159 at 60°C 0.375 at 50°C 0.52at45X 0.600 at 48°C
Chapter 4. H«at transfer
266 10*
(Temp. 24*C)
—\—!—I—r
lo'r-n—r
Un«
10*
Fluid
10*
S
8
Fig. 2 Shear stress-shear rate for typical nonNewtonian fluid used in this work.
1
.^ 8
\
I
M
>
I
I
r
Silicone oil
880
g 970 10' > ^
10»
870
>960|-
860
950 h 0
10» J \ I I I \ I L 10 20 30 40 50 60 70 80 90 Temperatur* (*C)
Fig. 1 Viscosity of Newtonian fluids used in this work. Experimental conditions 10-^ < Re < 10^ 4xlO^
i.au i...O: Results In the range Nu /Vl/3^jl/5 In the range Nu
H
= 1.0
Re <1.0 1 6
ip/D)(c/Df
lO
• = 0.45i?^^ Pr^'^Vi^
10^
Re'
940
10
20
30 40 50 60 Temperature CO
70
850
Fig. 3 Density variation with temperature for silicone oil andlub. oil used in this work.
4.1 Singto phas«
Notation clearance between impeller tip and vessel wall, m c Cp specific heat capacity of fluid, J/kgK D impeller diameter, m h impeller height, m H liquid height, m k fluid thermal conductivity, W/mK N impeller rotational speed, 1/sec fib number of impeller blades Nu Nusselt number, hjT/ky dimensionless P power input, W Pr Prandtl number, Cpfi/k, dimensionless p impeller pitch, m T tank diameter, m Vi viscosity ratio, /i/^«r, dimensionless w impeUer width, m Re Reynolds number, pND Vfi or pND Vpu* dimensionless y shear rate, 1/sec // Newtonian viscosity, k g / m s e c /44 average apparent viscosity, kg/msec ^w viscosity at wall temperature, kg/msec p liquid density, kg/w? T shear stress, dyne/cm^
267
258
Chapter 4. Heat transfer
Aksan (Sizgek), D., Borak, E and Onsan, Z. I., Can. J. ofChem. Eng.y 65,1013 (1987) Heat Transfer CoefiBcients in Coiled Stirred-Tank Systems Experimental apparatus System (1) single tank (2) two-tanks-in-series Vessel Type: flat-bottomed Diameter: 0.20 m Height: 0.24 m Liquid contained Height: 0.17 m Impeller Type: flat-blade turbine Diameter: 0.08 m Number of impellers: 1 Number of blades on impeller: 6 Width of anchor arm (perpendicular to shaft): 0.02 m Off-bottom clearance: 0.06 m Heating coil Tjrpe: helical coil Coil diameter: 0.16 m Coil-tube diameter: 4.35 mm ID Coil spacing: 6.35 mm Working fltiids Fluid in heating coil: hot water Fluid in tank: cold water Experimental conditions Impeller speed: 200,380,450 and 500 rpm /?^=19,000-77,000 Results HI = 0.023{H/DH)(cH^t/kf^iDHVHPk
/jutf-'ifn,/fi^f'
HO = 1.40 (k/DT)(NDi p . /fitf'\c„tit
/kf^(tit
Notation Ch Cw DT, DA* Dcf DH HI HO k N VH ph pw p,b liu,
[1+3.5 (DH /DC)]
/fi.f'*
specific heat, hot water, J/kg°C specific heat, cold water, J/kg°C tank, agitator, coil, coil tube diameter, respectively, m individual heat transfer coefficient, inside coil, W/m^**C individual heat transfer coefficient, agitated side, W/m^°C thermal conductivity of water, W/m°C agitator speed, 1/sec or 1/min velocity of hot stream, m/sec density of hot water, kg/m^ density of cold water, kg/w? viscosity at bulk temperature, kg/msec viscosity at wall temperature, kg/msec
4.1 Singl«phas«
269
Frobese, D.-H. and Bohnet, M., Chem. Eng. TechnoL, 12,324 (1989) Heat Transfer to Liquids and Suspensions in Agitated Narrow Vessels Experimental apparatus Vessel and impeller geometries
double jacket
0 s 908 mm Dj s Z20 mm Lj s 890 mm H/Os 3 d / 0 = 0.3-0.52 h,/D= 0.5 a,/0= 1 b/0 s 0.1 3 propeller mixer
-baffle cooling coil
\ 1 ^-—^-^^
pitch of propeller blade 30*
section A - A
Diagrammatic representation of the agitated vessel used in the tests.
Working fluids and their physical properties Fluid in jacket: saturated steam Fluid in tank: water and aqueous Drivanil solution Properties of pure Drivanil density: 1,074 kg/m^ viscosity: 18,000 mPasec thermal conductivity: 0.175 W/mK specific heat: 2.08 KJ/kg-^'K Experimental conditions Temperature of tank liquid: 50~80°C Viscosity of tank liquid: 0.355—73 m P a s e c Results Re > 10* Nu = 0.5i?e2/3pj^i/3(yy/^^)ai4
Geometrical data of employed propeller mixers.
270
Notation Cp specific heat capacity of liquid, J/kgK d impeller diameter, m D vessel diameter, m n impeller speed, 1/sec Nu Nusselt number, aZ)/A, dimensionless Pr Prandtl number, Cp t] /A, dimensionless Re Reynolds number, nd ^p/ T], dimensionless a heat transfer coefficient, W/m^K T] viscosity of liquid, Pasec T] „ viscosity of liquid at wall temperature, Pasec A thermal conductivity of liquid, W/mK p liquid density, kg/w?
Chapter 4. Heat transffar
4.1 Singl* phas«
271
Wang, K. and Yu, S., Chem Eng. Sci., 44,33 (1989) Heat Transfer and Power Consumption of Non-Newtonian Fluids in Agitated Vessels Experimental apparatus Vessel, cooling coil and agitator geometries Schematic diagram of cooling-tube configuration
Inner helical coils
I
I
Vertical tubes
External helical coils
Chapter 4. H«at tninster
272 Genmetrical configuration of impellers Type
Scale
Form
d = 0.092 b = 0.0184 tip = 3,6 «« = 2,3
Flat blade disc turbines
d:dt:b:dr =
l:l/4:l/5:2/5
c::i^^
Pfaudler impellers
.1
d = 0.092 b = 0.0184 fip = 3, «« = 2,3 0=15^
50
(/ = 0.089,0.115,0.1035 Hp = 2, w« = 3,5 ^ = 30°
MIG impellers d/2'^d||^» d:di:wi:w2 = l: 0.347:0.216: 0.173
rf = 0.075,0.085,0.107 ftp = 2, w« = 1 b = 0.049
Plate paddles
d = 0.142 ^^ = 0.142 tip = 2, w« = 1 0=45°
d/2
Semi-elliptical impeller
15
Anchors
K=m=a
d = 0.181,0.194,0.2125 b = 0.169 tip = 2 «« = 1
4.1 Single phaM
273
Working fluids and their physical properties Aqueous solutions of CMC (less than 4%) n = 0.49-0.92 iir= 0.02-12 P a ( s e c r Results Jacket:
M = 0.4561
^
M (I]
(Zbsmd]
H
Cooling tube: f
^\2/»/
\l/3/
\<
k Notation width of a single blade, m b Cp specific heat, W/kgK d impeller diameter, m dr outside diameter of cooling tube, m D vessel diameter, m he fihn coefficient from fluid to cooling tubes, W/m^K hj fihn coefficient firom fluid to jacket, W/m^K E liquid height, m k thermal conductivity, W/mK K consistency index at bulk temperature, Pa(sec)" n flow behavior index «« number of impeller on the axis np number of blades of an impeller E power per unit mass, W/kg B inclined angle of blade, degree lia apparent viscosity of non-Newtonian fluid, Pasec Va kinematic viscosity, Va-liJpy mVsec p density, kg/m^
(D
\H
-1.63
Chapter 4. H«at transfer
274
Kizil9e5, E A. Onsan, Z. I. and Borak, E, Can. J. ofChem. Eng., 68,1057 (1990) Heat Transfer Coefficients in Finned-Coil Stirred-Tank Systems Experimental apparatus Vessel Type: flat-bottomed Diameter: 0.20 m Height: 0.24 m Liquid contained Height: 0.17 m Impeller Type: flat-blade turbine Diameter: 0.08 m Number of impellers: 1 Number of blades on impeller: 6 Width of anchor arm (parallel to shaft): 0.02 m Off-bottom clearance: 0.06 m Heating coil Type: helical coil with disc-type fins Coil diameter: 0.16 m Coil-tube diameter: 4.35 nmi ID Coil spacing: 5.0,7.0 and 11.0 nmi Working fluids Fluid in heating coil: hot water Fluid in tank: cold water Experimental conditions Re = 20,000-110,000 Rcc = 3,600-14,000 Results Steady-state experiments with variable agitator speed (W = 20.0 cmVs, M = 20.0 cmVs; to = 22.4''C, Ti = 69.0'»C) N /roO>are) tx Ti A4f
hs
(mm) 11.0 (A/= 0.0438 m^)
7.0 04/ = 0.0761 m^)
5.0 (A/= 0.0932 m^)
/ , \
(rpm) 125 200 300 400 500 125 200 300 400 500 125 200 300 400 500
(°C) 43.0 44.2 44.8 44.8 45.3 43.7 44.2 44.5 44.8 44.8 43.5 44.1 44.8 44.8 45.6
f KTT^2 >°-"V
IC^tib
NDlp„
*„= 0.001881^^ J .
A/*
;
CO 48.8 48.3 47.7 47.0 47.4 49.1 48.0 47.4 47.3 46.7 48.3 47.5 47.4 47.1 45.6 ^o•^/
\^^*
ML]
(m^) 0.0816 0.0781 0.0751 0.0733 0.0720 0.1002 0.0941 0.0886 0.0854 0.0831 0.1093 0.1023 0.0950 0.0910 0.0864 X
X0J07
h. [~) M I*/J
/to (fimied)
(W/m '•^O 2,640 3.541 4,726 3,869 6,131 5,456 7,336 6,916 8,406 8,277 3,545 2,420 4,717 3,529 6,109 4,963 7,345 6,328 8,362 7,508 3,540 2,258 4,771 3,293 6,122 4,648 7,337 5,903 8,415 7,072
4.1 SingI* phase
Notation A^, Af effective and fin areas, m^ Cu, specific heat of cold water, J/kg°C DAf DH agitator and coiltube diameter, m hf fin thickness, mm ho heat transfer coefficient, agitated side, W/m^°C hs fin space, nmi k thermal conductivity of water, W/m°C M cold water flow rate, mVsec N agitator speed, 1/min or 1/sec /o, h inlet and exit cold water temperature, °C Ti, Tz inlet and exit hot water temperature, **C W hot water flow rate, mVsec Ate, //«, viscosity at bulk and wall temperature, kg/msec pw density of cold water, kg/m^
275
Chapter 4. H«at transfer
276
Carreau, R J., P ^ s , J. and Guerin, E, Can. J. ofChem. Eng., 72,966 (1994) Heat Transfer to Newtonian and Non-Newtonian Liquids in a Screw Agitator and Draft Coil System Experimental apparatus Vessel and agitator geometries (all dimensions in m) Vessel diameter/): C1~C3=0.254
Liquid height in the vessel H: Cl=0.262, C2=0.255,C3=0.261in Agitator diameter d: C1~C3=0.150, A=0.220, />=0.147, «;=0.067, A=0.0159, Cte=0.012 m Coil Name CI C2 C3
Material Cr plated Cu Steel Copper
dc
he
du
dii
Cbc
Cc
n.
0.1827 0.1763 0.1887
0.205 0.2075 0.2175
0.0127 0.00635 0.00476
0.0095 0.0043 0.0032
0.0275 0.0285 0.0175
0.0060 0.0064 0.0065
10.5 16.5 19.5
Working fluids and their physical properties Fluid in vessel: Substance Vitreaoil HV32 Mixture HV320 Com syrup CMC Xanthan
Polyacrylamide
Cone. ( mass %) 100
* 100
«* 1.0 2.0 0.75 1.0 1.5 600nig/L 0.2 1.0
// (mass %) or m (mass %) 0.055 0.200 0.785 2.48 0.564 9.5 6.27 6.5 8.62 0.136 0.521 5.04
n (—) 1.0
1 i• 0.748 0.631 0.122 0.196 0.183 0.871 0.734 0.521
Cp
(kg/m^)
(W/mK)
a/kg-K)
856. 873. 885. 1,383. 996. 996. 995.
0.145
1,901
0.323 0.588 0.575 0.610
2,358 4,177
0.356
2,902
\ 1,195.
i
1 1 1
1 7
1
^Adjusted for desired viscosity. **Qom syrup slightly diluted to avoid crystallisation. Properties of distilled water used for solutions: ;i=9x 10"^ Pas, p =995.4 kg/m^* = 0.610 W/mK, c^= 417J/kgK
Fluid in coil: water
4.1 Single phas«
277
Experimental conditions Agitation speed = 0.67—3 rps Reg = 3-1,300 Prg = 500-30,000 Results (A ^°*^^ M* = 0.387/?^f"/V;^' —
R e g = ^ ^'=
k
Notation Cp heat capacity, J / k g K d agitator diameter, m die outside diameter of the coil tube, m he liquid-side heat-transfer coefficient, W/m^K k thermal conductivity of hquid, W / m K ks the Metzner-Otto constant m consistency index of the power law, P a s e c n power low index, dimensionless lis number of coil loops N rate of rotation of the agitator, 1/sec Prg generalized Prandtl number, dimensionless Reg generalized Reynolds number, dimensionless /J, viscosity of Newtonian fluid, P a s e c 77 effective viscosity, Pasec p liquid density, kg/w?
Chapter 4. H«at transter
278
4 . 2 Multi phase 4.2.1 Solid-liquid systems Mizushina, T, Ito, R., Koda, S., Kabashima, A., Hiraoka, S. and Nakamura, T., /. Chem. Eng. Japan, 10,160 (1977) Heat Transfer under Solidification of Liquid on Agitated Vessel Wall Experimental apparatus Vessel Type: flat-bottomed Diameter: (1) 16 (2) 7 cm Height: (1)16 (2) 7 cm Liquid contained Height: (1)16 (2) 7 cm Impeller Type: (1) (2) anchor Diameter: (1) 15.2 (2) 6.2 cm Height: (1)15.2 (2) 6.1 cm Number of impellers: (1) (2) 1 Working fluids, solids and their physical properties Liquids: lauric acid, capric acid, and water Solids: lauric acid and capric acid Thermal conductivity (kcal/mhr'^C)
Specific heat (kcal/kg°C) Viscosity (g/cmsec) Density (g/cm^) Melting point CC)
Lauric add
Capric acid
Water
0.140
0.121
0.38 (solid) 0.515
0.32 (solid) 0.440
0.533 (40^0 0.548 (50) —
0.0688 (50°C) 0.0537 (60°C) 0.8744 (41.5°C) 0.8707 (50,25°C) 43.20
0.0434 (50°C) 0.0288 (70X) 0.8884 (35.05^0 0.8773 (50,17°C) 31.00
0.999 0.00656 (40°C) 0.00549 (50°C) 0.9922 (40X) 0.9981 (50X) 0.0
4^2 MuttiphaM
279
Results (hiDL
A
= V^ UW
1/3 >r
x0.14
I—
DL=D'2S
iPPildf
V^ = 0.15 {T]iPDL/d)ln(DL/d)} 1/3 r7 = l+exp
-o(a_:
--(f)(fl] Notation c^ specific heat, cal/g°C d impeller diameter, cm D vessel diameter, cm DL apparent vessel diameter, cm hi convective heat transfer coefficient, cal/cm^sec°C N rotational speed, 1/sec P correction feictor S solid layer thickness, cm 7] correction factor, dimensionless A thermal conductivity of liquid, cal/seccm-°C // viscosity at bulk temperature, g/cmsec ^w viscosity at wall temperature, g/cmsec p density of Uquid, g/cm^ y/ correction constant, dimensionless
Chapter 4. H«at tninster
280
Kung, D. M. and Harriott, R, Ind. Eng. Chem. Res., 26,1654 (1987) Heat Transfer to Concentrated Suspensions in Agitated Systems Experimental apparatus Vessel Type:flat-bottomedvessel with slightly sloped bottom Diameter: 15 in Height: 18 in Liquid contained Height: 15 in Baffle Number: 4 Width: 2 in Clearance of bafflefromwall: 1/8 in Impeller sixflatbladed 45° pitched blade turbine turbine Type Diameter (in) Number of impellers Number of blades on impeller Off-bottom clearance (in)
4 1 6
marine-t5rpe propeller 3.8 1
4 1
4
Cooler and heater Jacket heat transfer area: 2.19 ft^ Hehcal cooling coil: diameter: 7.5 in diameter of tubing: V2 in heat transfer area: 2.16 ft^ Working fluid, solids and their physical properties Liquid: water Sohd: polystyrene beads and quartz sand
polystyrene beads RH1911 ROMAXL.195 quartz sand Agsco Nolo
3p [xm
J/(msK)
c J/(kgK)
P kg/m'
190 680
0.084 0.084
1.340 1,340
1,050 1,050
710
2,650
45
kp
L73
Experimental conditions Impeller speed: 300—540 rpm Volumefractionof dispersed phase: 0~40%
4.2 MuKiphas*
281
Results Turbine
hdhc^ = 1 -1.25 ^
Propeller
hr/hc'' = 1 -1.03 0r
Pitched turbine