Fats and Oils Handbook
Michael Bockisch Hamburg, Germany
Champaign, Illinois
This book is dedicated to my wife Gudr...
3913 downloads
9394 Views
51MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
Fats and Oils Handbook
Michael Bockisch Hamburg, Germany
Champaign, Illinois
This book is dedicated to my wife Gudrun to whom, in the course of doing this translation, revision, and update, I had to break my promise never to write a book again, and also to my son Benjamin and my daughter Valerie. AOCS Mission Statement To be a forum for the exchange of ideas, information, and experience among those with a professional interest in the science and technology of fats, oils, and related substances in ways that promote personal excellence and provide high standards of quality. AOCS Books and Special Publications Committee E. Perkins, chairperson, University of Illinois, Urbana, Illinois J. Endres, Fort Wayne, Indiana N.A.M. Eskin, University of Manitoba, Winnipeg, Manitoba T. Foglia, USDA-ERRC, Wyndmoor, Pennsylvania L. Johnson, Iowa State University, Ames, Iowa Howard R. Knapp, University of Iowa, Iowa City, Iowa J. Lynn, Edgewater, New Jersey M. Mathias, USDA-CSREES, Washington, D.C. M. Mossoba, Food and Drug Administration, Washington, D.C. G. Nelson, Western Regional Research Center, San Francisco, California F. Orthoefer, Monsanto Co., St. Louis, Missouri M. Pulliam, C&T Quincy Foods, Quincy, Illinois J. Rattray, University of Guelph, Guelph, Ontario A. Sinclair, Royal Melbourne Institute of Technology, Melbourne, Australia G. Szajer, Akzo Chemicals, Dobbs Ferry, New York B. Szuhaj, Central Soya Co., Inc., Fort Wayne, Indiana L. Witting, State College, Pennsylvania Copyright 0 1998 by AOCS Press. All rights reserved. No part of this book may be reproduced or transmitted in any form or by any means without written permission of the publisher. The paper used in this book is acid-free and falls within the guidelines established to ensure permanence and durability.
Library of Congress Cataloging-in-PublicationData Bockisch, Michael. [Nahrungsfette und ole. English] p. cm. Updated and revised translation of the original German work, Nahrungsfette und ole. Includes bibliographical references and index. ISBN 0-935315-82-9 (alk paper) 1. Oils and fats, Edible-Handbooks, manuals, etc. I. Title, TP670.B5713 1998 6 6 5 4 ~ 12 Printed in the United States of America with vegetable oil-based inks. 543 06 05 04
98- 11974 CIP
Preface Oils and fats have been constituents of human nutrition from ancient times. First, they contain the highest level of energy of all components of food; second, they supply essential elements for the body. However, the fundamental reason for their early and varied use was certainly the fact that they contribute to the development of flavor, making dishes tasty and giving them a good, smooth mouth-feel. In the course of his life, a human being living in the industrial nations consumes approximately three tons of fats and oiIs; about half of them are so-called invisible fats, hidden in other food, e.g., sausage and cheese. In the developing countries, the portion of fat in food intake lies far below the amount recommended by the World Health Organization (WHO). This is not due to limited world resources, but rather to problems of local purchasing power as well as logistics and distribution. Cultivation could easily rise considerably faster than the world population. Fats are an important factor in the economy because of their status as basic constituents of nutrition and the large amounts consumed. This becomes apparent in their ranking second in worldwide traded items. For some countries or regions, they represent an indispensable part of the gross national product and a source of foreign currency. Because of the development of new varieties of oil seeds, the areas under cultivation have been extended in the past decades from the earth’s sun belt to regions of temperate climate, which now deliver a substantial part of that crop. This has led to a shift in economic interests. ‘some of these factors will be discussed in this book to illustrate the large correlations that exist. This book will acknowledge the importance of fats and oils and give a survey of today’s state of the art in technology. Even when considering a topic that is relatively limited in scope, it is impossible for a single person to obtain more than a general view of the field. It follows that to give an adequate description, it is vital to have recourse to the knowledge base established over the years by the publications of many scientists and practitioners. I would like to express my thanks to all those colleagues whose findings and experiences formed a basis for my studies. Technology is not an end in itself. It is justified when it makes it possible to improve the foodstuff offered by nature in whatever way, whether in amount, cost, quality or other criteria that make possible its use or adaptation to our way of life today. To pursue food technology without knowing the “raw material” would mean working in a vacuum and performing “l’arrpour I’m.” In this book, great attention was thus paid to describing the sources of the oils and fats, and also the fats and oils themselves in such a way that the technological steps be well-founded and the purpose clear. Since the industrial revolution, there has been a great boom in the industry of edible fats and oils. The processes that remain in use today are founded on basic findings from approximately 100 years ago. Much has been improved since that time, and many facts already known are exploited today only on the basis of improved technology. Technology will continue to develop in parallel with man’s changing attitude to it. In the broadest sense, progress in biological science and biotechnology contributes to this. Because biotechnological processes are reputed to be more natural V
vi
Preface
than chemical ones, there is an attempt to use enzymic reactions for fat technology. Much more far-reaching effects can be achieved by cultivation or the application of gene technology. Plants containing fats and oils in a desired composition, structure and quality render superfluous certain steps of treatment or modifications. To date, agriculture has not yet fully realized the potential offered by the cultivation of tailormade plants for certain purposes, as opposed to mass cultivation. In addition to these aspects, the development of machines and equipment leading to a more responsible way of dealing with raw materials and the environment continues. New processes of refining are confined mainly to physical modes of operation and protection of energy and water resources, in keeping with the spirit of the period and the desire to keep costs low. The manufacturers of such equipment are constantly engaged in new and further developments. Here, I would like to thank the companies that are mentioned subsequent to the bibliography for their support in providing pictures and information. This book will survey the raw materials predominantly employed and the spectrum of processes used today. Man’s ability to absorb information visually, i.e., via pictures, is many times greater than through the other senses or through transposition from language. A diagram or figure conveys more than a thousand words. To impart information quickly and efficiently, a focus of importance in this book was the explanation of technological steps in the form of graphs, a form of presentation that offers the reader a quick orientation and conveys a general view. Sufficient detail is offered to highlight the critical points without obscuring the presentation of essential information. In that sense, this book can be considered a sort of picture-bookhopefully, in a good sense. Michael Bockisch Vienna, I993
Preface to the English Edition AOCS Press has decided to publish this (originally German) book in English, updated and revised, and I am very grateful for the opportunity to expand its distribution and readership. The book was written primarily for Europe, and especially for Germany; some parts of Chapter 1, in particular, focus on the home situation. These parts have been changed where possible to give a broader picture. However, some figures remain in their original form, describing the situation in Germany. This was the case whenever they were too specific to be changed or when they illustrated certain facts that may well be used as an example for other regions in the world or as representative for the European Union. It is an honor to be able to reach a much wider readership. I translated the book to the best of my ability; however, without the help of my son, Benjamin, who had to do a lot of proofreading, of Ralf Tonn, who assisted me with the translation of Chapter 1, and especially of Iain Gow, Greg Knoll and Michael Gude, who did their very best as co-readers to improve my style, I (or you as the readers) would have been worse off. Both my readers and I owe them our thanks. In the interim between the original German issue and this one, almost half a decade has passed, and some of the trends that could be seen on the horizon have intensified. The skepticism towards any form of technology has increased in some countries, especially Scandinavia and the German-speaking countries, coming very close to hostility at least in some parts of the population. This deepens the gap between the wealthy countries that can afford to reject useful technology and those parts of the world in which technology is urgently needed to feed the increasing and often poor population. It seems that part of today’s fat technology will disappear in Europe or that chemical processes will be replaced by physical ones regarded as more environmentally friendly or by enzymic ones regarded as biological and thus, natural. On the other hand, there is total rejection in some quarters of new technologies such as biotechnology whether the concern is enzymes and their methods of production or genetically modified organisms (GMO). The contradiction between the existence of less technology and the development of new plants that may save some processing steps will be difficult to resolve. The next two to three years will determine where these new developments will be accepted and where they will not. A start was made in 1996 with the introduction of GMO soybeans, with other modified oilseeds following mainly in 1998. Lastly, I hope my readers will follow the advice of the great German poet Wolfgang von Goethe, who said: “Also, we should not deny that we are willing to forgive one or the other typing error in a book because we feel flattered by the fact that we detected it.”
Michael Bockisch Hamburg, 1997
vii
Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
v
Chapter 1
The Importance of Fats. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1. A History of the Production of Oil and Fat 1.2. Fat in Food and Food’s Raw Materials 1.3. The Economic Importance of Oils and Fats 1.4 Fat in Nutrition 1.5. Fats and Oils in Legislation 1.6. Fats as Technical Raw Materials 1.7. Fats and Oils as a Source of Energy 1.8. New Sources of Raw Materials 1.9. Substitutes for Fat 1.10. References
1
Chapter 2
Composition, Structure, Physical Data, and Chemical Reactions of Fats and Oils and Their Associates . . . . . . . . . . . . . . . .53 2.1. Components of Fats and Oils 2.2. The Structure of Triglycerides 2.3. Physical Characteristics 2.4. Chemical Reactions 2.5. Lipids 2.6. References
Chapter 3
Animal Fats and Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1. Milk Fats 3.2. Rendering Fats 3.3. Marine Oils 3.4. References
121
Chapter 4
Vegetable Fats and Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1. OiVFat-Containing Plants 4.2. Pulp Oils 4.3. Seed Oils 4.4. Nonedible Oils and Fats 4.5. Other Oil Sources 4.6. References
174
Chapter 5
Production of Vegetable Oils and Fats 5.1. Pulp Oils 5.2. Seed Oils and Fats
......................
345
Chapter 6
Modification of Fats and Oils . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1, Application and Combination of Modification Processes 6.2. Fractionation 6.3. Winterization 6.4. Interesterification 6.5. Hardening 6.6. References
446
ix
X
Contents
Chapter 7
Refining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1, Economic Importance of Refining 7.2. Neutralization 7.3. Bleaching 7.4. Deodorization 7.5. Physical Refining 7.6. Energy Consumption and Investment 7.7. Importance of Refining for Removal of Environmental Contaminants 7.8. References
Chapter 8
Fat as, or in, Food . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1. Butter 8.2. Margarine 8.3. Edible Fats 8.4. Salad and Frying Oils 8.5. Mayonnaise 8.6, Vegetable Creams, Cream Substitutes 8.7. Peanut Butter 8.8. Margarine and Oils with Medium-Chain Triglycerides 8.9. Monoglycerides and Diglycerides 8.10. References
719
Chapter 9
Analytical Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1, Acid Number 9.2. Saponification Number 9.3. Iodine Value 9.4. Peroxide Value 9.5. Unsaponifiable Matter 9.6. Water Content 9.7. Phosphorus Content 9.8. Color 9.9. Hexane in Extraction Meal 9.10. Fibers in Extraction Meal 9.1 1. Protein in Extraction Meals 9.12. Ash Content 9.13. Solid Fat Content 9.14. Dilatation 9.15. Lipids Analysis
803
Chapter 10
Conversion Tables and Abbreviations. . . . . . . . . . . . . . . . . . . . . . .
809
Chapter 11
Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
813
Chapter 12
Bibliography. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
815
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
819
.613
Chapter 1
The Importance of Fats The importance of fats for humans, animals and plants lies in their high content of energy, which permits the greatest possible storage of energy in the smallest possible amount of food substance. In addition, fats allow humans and animals to consume fat-soluble vitamins and provide them with essential fatty acids, that is, those indispensable fatty acids that their bodies are unable to synthesize themselves. Fats are omnipresent in nature, although in the most diverse quantities. In the human body, they play a decisive role as well, beginning with the nutrition of the infant with breast milk. During the first 5 d, breast milk contains an average of 29.5% fat; from d 6 through 10, the amount is 35.2% and later 45.4% (Macy 1949). In the course of life, a human living in the industrial world satisfies an average of >40% of energy demand with fat. Metabolized in the human body, fats yield 38 kj/g of energy (9 kcal/g). In this exothermic reaction, -2000 mL of oxygen per gram of fat is consumed and -1400 mL of carbon dioxide is produced (Peters and van Slyke 1946). In addition to -63 ton of water, 0.5 ton of alcohol, 8 ton of carbohydrates and 2 ton of proteins, humans consume -3 ton of fat during their lives. The efficiency of fat as foodstuff is very high, because the fat contained in food is almost completely reabsorbed by the body; in the feces (in the course of one’s life -5 ton, plus 30 ton of urine) only 3.3% of lipids can be found (Pimparkar 1961). Thus, fats play an indispensable part in nutrition as supplier of energy, source of compounds that the body cannot synthesize by itself, and carrier of vital substances. Fats cannot be replaced by other substances. Apart from this physiological aspect, they are excellent carriers of flavors, and dishes prepared with fats are much tastier than others. Fats also provide a smooth, creamy consistency to many dishes, which translates into a good mouth-feel. This explains in part why the consumption of fat is still very high today, even though the segment of the population performing hard labor has diminished greatly compared with the past, rendering a very high supply of calories no longer necessary (see also Chapter 1.4). The improvement in flavor, in particular, is certainly the reason why fats and oils have been appreciated for a long time. However, only since the beginning of the present century has it been possible in the industrial nations to provide the population with sufficient quantities of fat at reasonable prices (see Chapter 1.3). Because of this increasing importance of fats and oils, governments have intervened to a great extent in their production and distribution in the last 100 years (see Chapter 1.5). European food legislation, in particular, has often been marked by protectionist objectives. The importance of fats and oils to the global economy (Chapter 1.3) becomes clear when considering the amount of oilseed and fruit grown worldwide. In 1995, -60 million ton of palm fruit and -1 1 million ton of olives as well as >200 million ton of oilseeds were harvested. From these amounts, >90 million ton of oils and fats were derived. Many countries are trying to enlarge their shares in the interna-
2
Fats and Oils Handbook
tional market, a strategy that is usually to the disadvmtage of others and leads to defensive measures. National interests play a part here. For example, 10 years ago, the European Union began to promote the cultivation of sunflowers and rape in the area of the Community. A simultaneous attempt to stabilize the Community’s budget deficit by introducing a tax on fat caused the U S . to fear for its soy exports, resulting in a threat of trade obstructions aimed at the European automobile industry. The confrontation was averted in 1987, but it will reappear again and again, unless the issue of a tax on fat is buried for good. In addition to the importance of oils and fats for human nutrition, there is a substantial market for technical fats. The importance of these oils and fats will increase considerably in the future because they represent a vast potential of naturally regenerating raw materials in which the chemical and pharmaceutical industries have a special interest. A short survey of these technical fats is given in Chapter 1.6. The importance of oils and fats for human nutrition, the animal feed produced from the processing of most oil plants and the economic importance of oils and fats, i.e., the fact that many millions of people worldwide make a living by the production and processing of oils and fats, all combine to give special importance to technology. This may even be enhanced if oil-bearing crops could be offered to the chemical industry as a source of regenerating raw materials. Only -1% of -300,000 existing species of plants has thus far been examined for their qualifications as useful plants. Only 300 of these, i.e., 0.1%, are being used agriculturally today. About 7% of these, -20, are oil plants. A considerable potential, which may be suitable for the recovery of oil, thus remains. This is especially true when plants with a special fatty acid pattern are desired. In addition, there are new methods of plant breeding that also may open up new prospects.
1.1 A History of the Production of Oils and Fats From ancient times, man unconsciously consumed fat in his food via plants, fish, and meat. However, the use of oils and fats required some simple techniques. For example, only when the ability to make fm was discovered was it possible to melt the fat of hunted animals and store the fat. Storage also required the ability to produce vessels made from clay or another materials. Mutton tallow and lard, and later butter, cream, and fish oils were known in prehistoric times (Hanssen and Wendt 1965). Vegetable fats from olives and sesame seed, and possibly flax were also known. Until the previous century, the utilization of fats and oils as food went hand in hand with their use as fuel, predominantly for purposes of illumination. Even today, the name “lampante” for certain qualities of olive oil refers to this. As a base for ointments and cosmetics, they are still in use today, just as in the earliest periods. It is known from pictures that food factories were in existence in early days. Wooley (1929) presented a picture of an Egyptian dairy-farm that illustrated, among other things, the process of churning. Erman and Ranke (1923) showed the sequence of operations of a large-scale Egyptian bakery of Ramses 111 in Thebes
Importance of Fats
3
around 1200 B.C. in which a dough resembling a Chelsea bun is being baked in oil. People in the Mediterranean region and in Asia used oils long before those in Central Europe. With olives in the Mediterranean area and sesame in the area of the Euphrates and Tigris, oil plants that do not grow in the temperate latitudes were readily available. The Bible mentions oil in many passages. Moses, for example, required oil as a donation for the Tabernacle’s lamps; cake and pancakes were baked with unleavened oil (2 Moses 29). It was customary to anoint with oil, and Jacob anointed a stone this way to sanctify it. Passages in Luke indicate that oil was a valuable commodity. For instance, there is a description of how a person owed 100 barrels of oil to somebody else (Luke 16: 5.6). The importance of the olive tree to the people in the Mediterranean region also became visible by its being consecrated to the goddess of wisdom, Athene, in ancient Athens; it later became the symbol of peace and promise. Thus, after the Deluge, the dove came to Noah with an olive leaf in its beak (1 Moses 8:1l), a symbol of the world’s survival. Plinius described how to extract olive oil by pressing ripe fruit in a squeezing vise, a procedure customary in his time. Butter (“dense, solid milk foam”) was also mentioned, but only as a replacement for olive oil in times of need, or for baking. Another familiar practice of fat technology was the remelting of lard for cleaning purposes. Roman fat technology spread throughout the Mediterranean region. Excavations in Tunis show its propagation in Northern Africa; in Pompeii and Herculaneum, entire processing facilities consisting of oil mills, oil presses, oil shops, and oil depots were uncovered (UNION 1959). Because the fatty acids corroded copper, oil was transported in vessels made of lead, but also in tanker vehicles. These were carts carrying animal skins enclosed in iron hoops in which the oil was kept. Poppy seed has also been discovered in Swiss lacustrine dwellings dating from the 25th century B.C. It is probable that the inhabitants already knew poppy oil and that people north of the Alps became familiar with oil mainly through the occupation by Roman troops. According to tradition, oil was also extracted from beechnuts that were mashed, then wrapped in cloths and pressed between plates of metal or stone. Every large farm extracted its own oil. Later, agriculture made further progress, and rape and linseed were added as oil fruit. In the 16th century, the profession of the oil miller, who processed the farmers’ seeds, evolved. The oil was extracted by grinding, bruising, or pressing. Later, people shifted to squeezing vises. Windpower was used as propulsion in windmills. In the course of further development, hydraulic presses were built, and from the middle of the 19th century on, it was possible to extract oils and fats from the seeds by means of solvents. When the seafaring European nations conquered the world, the resources were expanded and unknown types of oil fruit with much higher contents of oil and fat than those previously known were brought to Europe. Until the cultivation of soybeans was widely expanded, these oilseeds yielded the substantial part of vegetable fats and oils consumed in Europe. The explosive increase in population in the industrialized countries of the world during the industrial revolution, combined
4
Fats and Oils Handbook
with urbanization, led to a new situation. The population that gathered in the cities had to be fed. This required an entirely new system of food distribution, which adapted itself to the change from domestic supply in small units (farms, villages or small towns) to industrial production. New requirements for food arose, especially concerning its preservation. New products such as margarine (see Chapter 8) and novel techniques such as hardening (see Chapter 6.4) made important contributions to mastering these challenges. Although the main concern in the late 19th and early 20th centuries was the satisfaction of basic needs, in today’s industrial society, there is no longer a problem of quantity. After the decline in food production caused by the two World Wars and the Great Depression, during which the question of “mere nourishing” became important, the essential aspect of the 1960s and 1970s was that of enjoyment. The primary function of food was no longer the supply of calories, but the experience of taste. Accordingly, the focus shifted from the production of quantities, which were in fact available, to quality. In particular, the emergence of the trend toward health consciousness has stimulated the demand for quality. Here the fat industry delivered exceptional contributions. The connection between cardiovascular disease and nutrition was detected in the early days. This knowledge was used to develop special products that provide preventive measures (e.g., becel; see Chapter 1.4). The excessive fat consumption of most of the world’s population and the consequences of overweight have led to the development of reduced-fat and very-low-fat variants of the most diverse types of food. For margarines, for example, the law had to be changed to allow this. Starting with margarines, food groups developed that made possible low-calorie nutrition, or, as in the case of becel (a trademark of Unilever concern), furnish variants of diverse foods free of or low in cholesterol and high in polyunsaturated fatty acids. In recent years, a new trend could be observed developing in parts of the population. Sensitized by a growing awareness for environmental issues, “naturalness” of products has been given high priority. Although the demands resulting from this are partly exaggerated and no longer have a clear foundation, it will lead to changes in technology in some fields, at least in the wealthier countries. In poorer countries, which strive to produce food for mere nourishment and survival, there is little patience for these trends. The priority here is to feed the population. Although the strong increase in population is no doubt leading to problems that cannot be overestimated, the production of fats has always increased at a rate higher than the population growth (see Chapter 1.3).
1.2 Fat in Food and Food Ingredients Fats and oils, as such, are used for the production of food; in addition, unprocessed food or ingredients for food production contain fats and oil, sometimes in substantial quantities. These include fruits and vegetables but also meat and fish (Table 1.1). For oil and fat technology, these figures are important because they help identify the raw materials for oil and fat production. In processed food, oils and fats are
lmportance of Fats
5
TABLE 1.1 Approximate Fat Content of Unprocessed Food FruiVNuts
(O/O)
Bananas Oranges Pears Sw. chestnut Avocado Coconuts' Almonds' Hazelnuts' Walnuts' Pecan nuts*
0.2 0.2 0.4 2.0 17 34 54 62 64 71
VegetabledCereals
Fish
(%)
Meat
(%)
Potatoes Tomatoes Broccoli Cabbage Corn Barley Mushroomst Soybeans
Haddock Cod Mackerel Caviar Herring
0.1 0.3 11.5 15 19 26
Chic ken breast Roast chicken Boiling fowl
1 6 20
0.1 0.2 0.3 0.8 1 .o 1.5 3 20.9
Miscellaneous
Eggs Milk
Eel Shrimp Lobster Mussels
1.5 2 1.3
11.5 3.7
Rabbit
8
Fillet of beef Haunch of beef Beef tenderloin
4.5 7 10
Fillet of pork Pork chop Bacon (lean) (fat)
4.5 7.5 65 88
'kernels. +dried.
also found in diverse quantities. The variety of foods listed below (Table 1.2) ranges from those which are produced by a single treatment step (e.g., by grinding) to those that require many steps of processing because they are composed of many kinds of raw material (Table 1.2). The figures cited can vary considerably and thus serve only as a basis for the order of magnitude of the fat content of the food.
1.3 The Economic lmportance of Oils and Fats Nourishment is an indispensable and essential need of the human race. It is the task of agriculture and the food industry to satisfy this need. Considering the current develop ment of the world's population, a huge demand is arising. This demand has to be satisfied under the best possible conditions. There remains a shortage of supply in many parts of the world. Considering the fat-providing potential of agriculture and industry, this demand should be able to be satisfied easily. In past years, the production of fat has grown at a faster pace than the population (Fig. 1.1). A shortage of supply is thus rather a problem of distribution and purchasing power than one of shortage in the sense of lacking potential. In the coming years, the production of fat will also grow more rapidly than the world population. Mielke (1985) estimated a 1Cfold increase in oil production from the year 1958 to the year 2000. During this period, the amount of soybean oil will increase sevenfold and palm oil production will increase 2.5-fold. For palm oil, this prediction is already far outdated. In the past 10 years, the volume of oilseeds stored as surplus amounted to an average of 14% of production (Mielke 1990).However, as can be seen from Figure 1.2, there is a strong correlation between gross national product, reflecting the standard of living, and fat consumption. Chma, India, Pakistan and Bangladesh currently represent almost one half of the world's pop ulation. Demand for fat by these four countries will increase not only as their popula-
Fats and Oils Handbook
6
TABLE 1.2 Aproximate Fat Content of Processed Fooda Sausages
(YO)
Corned beef Wieners Bavarian veal sausages Cervelat sausage German Fleischwurst Mortadella Calf liver pate Salami Smoked s. spread
6 20 22 35 30 33 35 38 37
Baked products Rolls White bread Crisp bread Zwieback Rich tea biscuit
0.5 1.2 1.5 4 11
Spaghetti . _
1.2
sweets Sugar Caramel Cocoa (slightly defatted) Milk chocolate
Milk products
0 10 25
Yogurt, skim Condensed milk Cream (whippable)
0.1 4-8 27-33
33
Quark Fresh cheese Camembert cheese Edam cheese Parmesan cheese Emmenthal cheese Roquefort cheese Processed cheese
5-1 2 5-1 2 23 24 26 30 32 2 3-2 8
Cereal products Oat flakes Wheat bran Wheat flour Rye flour Corn flour Corn semolina Corn flakes Pop corn
6.5 10
1-2 1 -2 2.6 1.1 0.4 5
Snacks Potato chips Roasted peanuts
(W
(Oh)
40 48
Miscellaneous ~~~~
~
Mustard Salad mayonnaise Mayonnaise Margarine Butter Cod-liver oil
'?his analysis is from European f d ; all values are examples only and may differ from country to country according to local habits, local taste and local legislation.
World
fat production [MMT] 120 100
population [billion] 12
'
8060 -
40 -. World population
__
20 01936
194S
1956
1966
197s
1986
~
1 ' 1996
Fig. 1.1. Growth of world population and oilhat production.
2
0
6 52 82.5 80.5 82.5 99.8
7
Importance of Fats _.
Germany
us.
\
Gross National Product [lo00US$ per capita] Fig. 1.2. Average spending power and fat consumption in different countries (adapted from Leonhard 1995).
tions grow, but it can be predicted that a tremendous demand for fats and oils will be triggered as their gross national product improves. Statistics concerning the world production of oils and fats have existed only since 1942. Estimations at that time, as well as those concerning the years before, were coordinated by the International Agrarian Institute in Rome (today FAO; Schiittauf 1942). Since then, there has been a shift from animal to vegetable fats (Fig. 1.3). As for all food, consumer prices for oils and fats have dropped signfi-
Marine oils Lard, Tallow Butter Pulp oils Seed oils
Fig. 1.3. Proportion of different oil sources on the world fat production.
8
Fats and Oils Handbook
TABLE 1.3 Oil Seed and Oil Fruit Production in the World by Region (O/O of total) Region North America South America China India, Pakistan, Bangladesh USSR (successor states) Europe (without USSR) Africa Malaysia, Philippines, Indonesia All others
1935
1950
1960
1970
1980
1990
1995
17 7 15 11 9 21 7 6 7
24 8 13 9 8 18 8 7 5
24 9 9 9 9 19 9 6 6
27
28 11 7 8 1 15 6 9 6
26 12 9 6 1 0 9 15 5 13 5
24 13 12 1 4 14 4 14 4
10
7 8 1
2 17 7 5 7
cantly in relation to income. Rendered animal fats, and especially butter, were goods in short supply and thus very expensive. For example, in Germany in 1857, -15% of one’s daily food expense was needed to buy only 40 g of butter. In 1800, the entire expenditure for food amounted to -70% of a family’s entire income, in 1900 to -50% and in 1974 to -28%. Today in Western Europe, this fraction is clearly ~ 2 5 %(Gander 1984). The importance of oils and fats has increased during the past 100 years. Since the time before World War I, worldwide production has more than quintupled. The center of oil fruit cultivation was once situated in tropic regions, whereas today it is in temperate latitudes (Table 1.3). To counteract this trend, tropical countries, in particular, Malaysia, Indonesia and the Philippines strive hard to regain their former rank on the scale of producers. On the one hand, it allows them to feed their own growing population; on the other hand, it creates export possibilities and explains why the production of palm oil in these countries has been extended steadily and forcefully for about 15 years. The higher oil yields of cloned palms contributed to this in part. In Malaysia, production rose from 4 million ton in 1985, to -7 million ton in 1990 and to -10 million ton in 1995 (see Chapter 4.2.1). In that country alone, almost two million people make a living from palm oil, and in 1986, this branch of the industry yielded a revenue of almost $1.4 billion (US.). At the same time, these efforts are a prime example of the importance of oils and fats to certain regions of the world. Often, one region’s efforts to raise production are accompanied by countermeasures from another region. In the case of Malaysia, the countermeasure was an attempt to discredit tropic oils. The increase in the production of palm oil was regarded by the U.S. as a danger to its soybean oil market. Campaigns were started with the objective of pushing the tropic oils out of the country as completely as possible. In addition, new directives concerning labeling were passed, forcing the producers to declare the oils used. Public health policy was given as a reason; later, this proved to be true to some extent but that explanation was viewed by Malaysia as simply a pretext. Malaysia believed that concern about losses suffered in the production of soy seed
lmportance of Fats
9
was the actual reason (Anonymous 1987). After fractionation, palm olein is a good raw material (see also Chapter 1.4), and for many products and branches of industry, stearin is also used as a consistent fat. It is expected that the U.S. import of tropic fats will level off at -750,000 ton per year. Of the laurics (coconut and palm kernel oil), 70% go to oleochemical processing. The distribution of the individual types of oil fruit has changed considerably (Fig. 1.4) as shown by the comparison of their distribution in 1935, 1960, and 1995. A projection to the year 2000 (data from Mielke 1994) is also given. Figures 1.5-1.7 show the production of oils and fats during the last 80 years. The figures refer to the amounts of visible fats produced. A distinction must be made between butter, lard, and olive oil, which represent end products suitable for consumption (Fig. l S ) , vegetable oils and fats (Fig. 1.6), which have to be processed, and oils utilized mainly in industry (Fig. 1.7). To simplify the presentation, tallow, and fish oil, which are generally processed further, are listed together with butter, lard, and olive oil which are consumed as such. Figure 1.5 shows that the production of whale oil has virtually disappeared, whereas the production of fish oil is -10 times higher now. This can be attributed
(C = Corn oil; P = Palm kernel oil; S = Sesame seed oil)
Fig. 1.4. Proportion of different vegetable oil sources on the world fat
10
Fats and Oils Handbook
Fig. 1.5. World production of butter, lard, beef tallow, fish oil, and whale oil. mainly to various new catching methods. However, a stagnation of these figures has to be anticipated, also caused by international campaigns toward sustainable fishing. The high increase in tallow production mirrors the rise in beef production. The growth rates, however, are far lower than those of vegetable fats and oils; tallow is only a by-product. The rapid rise in the production of soybeans, which has increased 50-fold, is clearly visible. The growth rate of sunflower seed is even higher. Compared with these amounts, the production of oil-bearing plants utilized mainly in industry is modest; however, the fact that a considerable amount of the edible oils is used for industrial purposes must be noted (see Chapter 1.6). By looking at the production of fat and its products, the political development in the world or in particular countries can easily be inferred. Fat production in Germany (see Chapter 1.3.1), for example, was at its lowest level during both World Wars, but also during the great depression in the 1920s and 1930s. For a good supply at low prices and, related to that, an adequate profit for the farmer, the yield per hectare is essential because in the industrial nations only a high yield per hectare promises sufficient returns. However, during times of extensive shutdowns of areas (e.g., the US.),there are considerations if models exist that are based on less intensive tillage. The yield per hectare thus keeps rising, but at a far slower pace (Fig. 1.8). It is the yields per hectare that indicate the difference between developing and industrialized countries. Cultivation in Third World countries often takes place on very small farms in poor soil with an insufficient supply of water; for particular regions and their state of affairs, this clearly makes sense. Production in the industrialized countries can vary greatly as well (Fig. 1.9). Consider this comparison. By feeding cows the yield of 1 hectare (2000-3000 kg on average), only 2W300 kg of milk fat can be produced. Of course, one must
11
Importance of Fats
Soybean oil Palm oil
Rapeseed oil Sunflower seed oil
Cottonseed oil Peanut oil Coconut oil
Sesame seed oil Olive oil
Fig. 1.6. World production of important vegetable oils.
admit that, for milk, the production of fat is not the main objective. However, byproducts are also gained from most sorts of oil fruit. Not all influences on production can be controlled even when the means are available. The source of raw materials might be exhausted without the possibility of exercising any influence on it, or the opposite may be the case. For example, the production of fish oil in Peru (one of the largest producers, and for its size, by far the largest producer) decreased from 3 11,OOO ton year in 1976 to virtually zero in 1984. Excessive fishing was not the cause, as was speculated initially, but rather a change in the direction of the Humboldt stream, which shifted its flow 350 km to
Fats and Oils Handbook
12
1.5
E r 1.0 C
5 0
ze
Linseed oil Castor bean oil
10.5
P
Tung oil Sperm oil
0 1910
1930
1960
1970
19SO
Fig. 1.7. World production of main vegetable oils for industrial usage.
the west of the Peruvian coast. The fish followed the flow of the stream. The Peruvian boats, equipped for inshore fishing only, were not able to follow the stream, and the entire industry broke down completely. Chile profited from this: its catches in 1989 amounted to -6 million ton and -260,000 ton of fish oil were derived from it.
Fig. 1.8. Production yields of some selected vegetable oils.
Importance of Fats
13
Fig. 1.9. Production yield of some oilseeds in different countries.
The opposite occurred in the insular republics of South East Asia. There, devastating typhoons had gravely affected the coconut crop over many years. Without any identifiable reason, the typhoons changed direction, and the coconut industry began prospering again. World affairs interfere considerably with the production of oil but in different ways than the natural influences listed above. Their influence on oil prices is especially evident (Figs. 1.10 and 1.11). Wars, but also energy crises are mirrored here, although the supply of edible oil has hardly any relation to the production of mineral oil. Depending on the type, the price of vegetable oils is higher or lower than that of soybean oil, whereas the market value of animal fats lies, without exception, below that of soybean oil. However, it must be considered that fish oil, with very few exceptions, is used primarily in hardened form, so that in comparison with tallow and lard, the costs for hardening have to be taken into account. Tallow is usually fractionated before use. Because soybean oil has developed into the predominant oil, the prices of the other oils are to a certain extent dependent on that of soybean oil (Figs. 1.12 and 1.13). These figures show prices leveling off in years when edible oils strongly forced their way into the market and the difference in price for soybean oil, which has been relatively constant (except for some peaks). They also give an idea of the relative value of the various oils and fats. Considering the large volumes of oil produced, the high growth rates and the competitive situation, it is no surprise that oil prices have declined relatively. Depicted in U.S. $ against inflation in the U.S., it becomes obvious that oil prices
Fats and Oils Handbook
14
L I S M 1970 1975 1980 IS85 I990 1-
I I
1065 1970 1975 1980 1985 1990 1096
1400
1200
lo00
800
600400 200 Palm oil
0 1 1966
1970
1976
l&
1986
l&
l&
Fig. 1.10. World market prices of important vegetable oils.
in January 1990, in spite of the increase of the absolute amount in constant money, are only -36% of those in January 1965. During 1987, they dropped temporarily to only 25% of 1965 levels (Fig. 1.14). Taking into account the decline of the U.S. $ in proportion to the currencies of some European countries, the oil has become even cheaper. However, this is compensated partially by lower inflation rates (Figs. 1.15 and 1.24). Because of the historical development of the production of oil fruits in regions completely different from those in which they are consumed, the market has always been international. Oilseeds and oil are usually traded in U.S. $. Because
15
Importance of Fats
1200
Soybean oil
400
1985
1400
1970 1975 lSe0 1985 1990 1995
1985 1970 1975 1980 1985
lee0 1995
World market pnce [US. WMT]
1200 lo00
800
Ittoned oil
800 400 200
Soybean oil 0 '
1
19S5
I
1970
1975
IS60
1985
ID00
1996
Fig. 1.lo. Continued.
the European countries are not self-sufficient, they have to import oilseeds. For the oil milling industry outside of the U.S., which has to commercialize oil as well as meal, the deviation of the exchange rate of the U.S. $ to the respective currency (Fig. 1.15) is added to the deviation of the price for the raw material. This can exert quite a considerable influence on the market position because products made from vegetable oils and fats always compete with indigenous products (e.g., margarine with butter). In addition, extraction meals have to compete with indigenous fodder. The influence of the deviation of the U.S. $ exchange rates against the only stable European currency (German Mark) is made clear. One realizes that the deviation for the European
Fats and Oils Handbook
16
Edible Tallow
1965
1970 1975 1980 1985 1990 1995
1W5
1970 1975 1980 1985 1 W 1995
World market price [US. WMTJ I2Oo
I
1000
800
600
400
200 -.
0 ’
I
igss
1970
197s
is80
198s
isso
,
ims
Fig. 1.1 1. World market price of some animal fats (soybean oil as comparison).
market can thereby become even larger. In times of a powerful dollar, considerable price discrepancies arise that are difficult to pass on to the customer. Prices on the world market do not always depend on supply and demand alone, but also on expectations for the volume of the next harvest. Most deals are closed on futures long before the harvest amount is known. Besides the area that is going to be cultivated in the respective year, information about the expected weather is relevant. However, not even a major regional weather-related catastrophe would be capable of influencing prices substantially. The U.S. exhibits the greatest deviations in the area used for cultivation and thus the strongest influence
Importance of Fats
440
17
World market pnce dfference to soybcen 011 [US$/MT]
300
zoo
loo 0 -100
-100
300 400 1066
1970
1976
1980
1986
1990
1996
World market pnce dfference to soybean oil [US. $IMTl
Peanut oil
400
300
'
1066
1970
1976
1980
1966
1990
1996
Fig. 1.12. World market price difference of some vegetable oils and fats to the price of soybean oil.
on the amount of crop to be expected. According to the previous year's supply and achieved prices, areas of smaller or larger size will be shut down. Because soybean oil is by far the most-produced oil, its quantity influences the prices of the other oils and fats as well. Consequently, the number of acres cultivated in the U.S. in the respective year plays a very important role in the equation. During times of high supply, prices usually drop at harvest time and rise when the provisions run short. During this process, the quality usually declines as well; therefore Brazilian and Argentinean producers generally wait until the supply of the crop in the Northern hemisphere is exhausted, or the quality declines, before they commercial-
18
Fats and Oils Handbook
Fig. 1.13. World market price difference of some animal fats to the price of soybean oil. ize their crop. This is the only way to obtain good prices for relatively smaller producers with higher transportation costs. As a result of intensified cultivation in the Southern hemisphere, fresh soybeans are available twice a year. Apart from production and availability, demand also plays a decisive role in price. When comparing demand with availability, we see that the quantities pro-
Fig. 1.14. Price of soybean oil in current and constant money (US $).
Importance of Fats
19
Fig. 1.15. Price of soybean oil in U.S. $ and in a stable European currency (DM).
duced were almost without exception higher than the demand (Fig. 1.16). This leads to an accumulation, which depresses the prices. Malaysia alone is said to have had a stock of palm oil of -1 million ton in 1988-1989. The econoinic situation in the large countries that are not self-sufficient and are subject to monetary problems is closely linked to demand, and thus to a high
Fig. 1.16. Demand and supply balance for vegetable oils and fats (after Batterby).
Fats and Oils Handbook
20
degree, decisive for price development. On the one hand, there is the Soviet Union (respectively, the successor states), where the import of meals as fodder plays an important role. On the other hand, there is India, which represents a huge market with 9300 million people. In 1986-1987, -2 million ton of oils and fats were imported. The imports in the following years are estimated to be -0.5 million ton, but the most recent estimates suggest even lower amounts; however, the demand that cannot be met that way amounts to 1 million ton per year. In contrast to this, it is expected that Pakistan will increase its imports to almost 1 million ton. In view of these markets, the surplus production is within the range of the deviations of the quantities imported by these countries. The demands are thus not regulated by the actual demands, but by the availability of funds. When we relate the prices for oilseeds on the world market to those for oil, we have to consider that they are determined by the oil content as well as by the usability of the meal as fodder. We see that an intricate web of influences exists that determines the prices. This has direct influence on the supply, more so in some parts of the industrialized countries in which the price for seeds fluctuates around the limit of profitability despite subsidies. Without subsidies, production at today’s prices would not be possible. For the oil mills, the production of soy seed, for example, means that they have the following net profits (Prices Chicago, May 1990): Cost (US. $) lo00 kg 180-200 kg 820-800 kg
soybeans oil extraction meal
Cost of beans Gross profit from oil and meal*
Revenue (U.S. $)
322.12 193.68-2 15.20 134.55-13 1.27 322.12 328.23-336.47
*without any running and processing cost, without losses and depending on the oil content.
This margin (however simplistically calculated) is extremely small for a capital-intensive industry such as oil milling, so that small changes in the meal’s marketability or in the price would render the entire enterprise uneconomical. The economic importance of a raw material, however, reveals itself not only in the supply, but also in the demand. Because oils are traded internationally, their prices are not dependent on the demand in a single country. In addition, there are subsidies for agriculture in many regions. This has repeatedly given rise to international irritations when, for example, the U.S. reproached the European Community for violating the GATT-treaty by means of subsidies and by partially barring the market for agricultural imports (see Chapter 1.3.2). From Brussels’ point of view, these subsidies are necessary to assure some degree of self-supply for certain agricultural goods of the European Community.
lmportance of Fats
21
Subsidies can have other purposes, for example, as an incentive for structural reorganization. For instance, the Community supported the shift from the cultivation of rape with a high content of erucic acid (HEAR) to that with a low one (LEAR). It was intended to arouse the farmers’ interest in rape, which grows well in temperate climates, and to promote its cultivation instead of root crops and cereals, which are produced in excess. In 1988, the subsidy was 5.90 German marks (-3.30 U.S. $) per ton of rape (LEAR). The prices the producer can gain for his products on the market, however, are dependent on the demand in an individual country. In this respect, the price structure of butter and margarine in the individual countries is of interest. In some countries, for a large part of the population, margarine is a substitute for butter. The sales thus depend to a high degree on the relation between the prices for butter and margarine (Fig. 1.17). In Germany, for example, a portion of the consumers buy margarine whenever the price differential to butter increases beyond a certain value. This fact, which applies to other countries as well, was used by the EC-commission to diminish the “butter-mountain” by bringing butter onto the market at a reduced price. In the period from 1982 to 1985, heavily subsidized butter in the EC amounted to >2.2 million ton. To subsidize this quantity, which replaced 80% of the fresh butter, 1600 ECU per ton had to be paid (>3200 German marks or 1500 U.S. $ per ton at the exchange rates of 1986; Friedeberg 1986). In other countries, the image of margarine is completely different, and butter plays only a minor role. Interestingly, this also applies to the Netherlands and Denmark (buttedmargarine 1:7 and 1:3, respectively), countries that are commonly known as “milk countries.” 10
a
8
g
6
Butter
Vegetable
I
2 k
p.. margarine
Butter
4
.-8
Average margarine price
ti
2
0
,
i
I910
4
1930
I
,
1950
1970
1990
Fig. 1.17. Price differential of margarine and butter in Germany.
Fats and Oils Handbook
22
1.3.1 The Economic Importance of Oils and Fats as Well as of Fat Products in Europe and Germany
As stated in the preface, Germany is seen as a particular example of a western European country. In the past 50 years, nutrition habits in industrialized countries have changed drastically (Fig. 1.18), with Germany as an example. (Remark: all data in figures concerning Germany end with the year 1990 because data after the reunification would not be comparable.) In spite of diminishing hard physical labor, caloric intake has grown, and despite the findings and recommendations of nutritionists, the percentage of fat in the diet has increased. Since 1850, the consumption of fat in industrialized countries has risen constantly. It is assumed that the German population satisfies -40% of its energy demand with fats and oils. Currently, the amounts consumed consist of approximately equal shares of butter, margarine, and edible oil, as well as tallow and lard (Fig. 1.19). The proportion of margarine has dropped since the 1950s in favor of edible oil and fat. The market for emulsion fats altogether is currently dropping at a rate of -3% per year. The shift in proportions is disadvantageous for the visible fats, whose proportion or intake can be controlled consciously, and favors the invisible fats (proportion -1: I). Currently, the annual per capita consumption amounts to -30 kg of visible fats (Fig. 1.20). The history of fat policy in Germany (which is representative of other European countries) is depicted comprehensively by Schtittauf and Pischel(1978), whose work is referred to in part in the following paragraphs. Their overview reflects the political turmoil in Europe during the last 80 years. 200
0
I
6
eh)r
1940
I
w
* &--" #*-
1980
. .us*m --m -
1960
1970
1980
1990
Fig. 1.18. Per capita consumption of different food in Germany
Importance of Fats
23
Fig. 1.19. Proportion of some fats and oils on total fat intake.
Today, Germany’s self-sufficiency concerning vegetable oils and fats is quite low. About 90% of the raw materials are imported. In the early 1900s, Germany’s self-sufficiency for fats and oils was -50%; between 1945 and the present time, the overall self-sufficiency is -40%. Despite these shortcomings, there have always been attempts to impose special taxes on the import of oils and fats (fat-tax). Actually, this tax has never been directed against the fats themselves, but against fat products, especially margarine.
Fig. 1.20. Per capita consumption of visible oils and fats in Germany.
24
Fats and Oils Handbook
Toward the end of the last century, with the introduction of margarine, the first legal restraints were introduced; initially, these amounted only to sale restraints (e.g., no butter and margarine in the same room). However, a duty was imposed on the import of margarine or equivalent oil mixtures according to Bismarck’s policy of protective duties. Because this duty did not apply to individual oils but only to oil compounds or to finished products such as margarine, the first margarine plants were built directly along the border in The Netherlands, which were most progressive, so that transportation costs for the duty-free raw materials were as low as possible. During World War I, a considerable shortage of fat occurred. Naturally, imported fats and oils became scarce first, so that fats for margarine were not available in sufficient quantity. From 1917 on, only one third of the required volume of fat could be put on the market. In the respective figures, this becomes apparent through the lows in margarine production, and better yet, in the contrary development of the fraction of margarine and butter at that time. During the time of inflation, caused by the putative upswing during the postwar period, the number of margarine plants in Germany rose to several hundred (today the number is -10). On May 1, 1933, a fat-tax, combined with a fixing of quotas, came into effect in the Third Reich. The production of margarine was frozen at 60% of the 4thquarter output of 1932; moreover, a tax of 0.50 Reichsmark per kilogram of margarine, edible oil, hardened vegetable oil and whale oil was inflicted. An “Agency of the Reich for milk products, oils, and fats” was established. Soon, only a standardized margarine, packed in a simple, brown, unattractive wrapper was permitted to be marketed. As a consequence, 115 out of 148 margarine plants were forced to close. It was not until 1949 that branded margarine products were again permitted to be sold. However, at about the same time, the oil milling industry was financially hard hit because it was forced to sell to the agriculture sector meal at 50% of the world market prices. A fat-tax was again considered in 1950. It was prevented by protests from labor unions and social associations. Instead of the fat-tax, vegetable oils and fats were subsidized through the end of the Korean War. In later years, the fat-tax was considered several times, mainly during the times when there was an excess of butter, the so-called butter mountain, in the European Community. The fat-tax was consistently prevented. The primary reasons for the failure of the fat-tax included strong protests from consumer groups who feared higher prices. Another reason for the failure of the fat-tax was intervention by the U.S. (different reason than before), who did not want to see its export of soy products diminish because of the enormous rise in U.S. soybean production. At that time, the American soy farmers were feeling the effects of poor prices for their crop. Finally, this would have been the first tax that the EC could have inflicted, and increased independently from the individual governments. The EC certainly needed the revenues because subsidies of other agricultural products amounted to several hundred per cent (i.e., in 1977,220% for butter and 107% for olive oil).
Importance of Fats
25
The prices for fats and oils in Germany (as in other European countries with hard currency) in terms of constant money have developed differently from those in the U.S. Two opposing influences are operating here, i.e., the substantially lower inflation rate in Germany compared with that of the U.S. (over a period of 30 years from 1965 to 1995, only -56% of the U.S. rate) and the depreciation of the U S . $ with respect to the German mark (from 1965 to 1990, -45%). The effect is clearly visible in Figure 1.21. Presenting the price for soy on the world market in U.S. S as well as in German marks, according to the respective exchange rate and with an adjustment for inflation, one can see that soybean oil in Germany in terms of constant money costs only -30% of the amount in 1965 (U.S.: 36%; Fig, 1.21). This is reflected in the consumer prices for oils and products consisting mainly of oils and illustrates some of the problems of the fats and oil industry as a whole. After the reduction of the butter-mountain, which had temporarily reached >1.4 million ton, by means of regulative measures by the EC (quotas for milk), a certain pressure to intervene for regulating purposes has subsided. The next decisive step will be the integration of the different forms of agricultural producers in the new and old federal states of Germany into an all-German system. In the new states, a potential for the production of oilseeds is building up; in relation to the population, it is larger than that in pre-unification Germany. The European Union will be faced with the same problem when considering the membership of Eastern European countries such as Poland. Figures 1.22 and 1.23 reflect the situation in the German oil milling industry, which crushes about two thirds of the oil consumed. The development of the amounts of oil produced per variety reflects the European Union’s move towards rape and sunflower, and the crushings demonstrate the dominance of these two
Fig. 1.21. Price of soybean oil in current U.S. $, and current and constant DM.
Fats and Oils Handbook
26 I.o
I
0.8-
Er 0.6 -.-
0
0
3
Rapeseed oil
//I Palm kernel oil
Soybean oil
Oa4
T Peanut oil
\
I+
coconut oil
0.2
Sunflower seed oil
0 I910
1925
1940
1956
1970
1985
Fig. 1.22. Oil produced in German oil mills.
oilseeds over soybeans. Although more southern countries such as France are crushing relatively more domestically grown sunflower seed, this picture can be regarded as typical for Western Europe. In spite of the difficulties with eamings and profits and the strong competition from abroad, the quantities processed increased until 1980 and have since remained
r-
6
5
€ 4
f . P i
e
seeds (total)
Meals (total)
Soybeans Rapeseed Soy meal
2
a
Oil (total)
I
0 1910
1925
1940
1956
1970
1985
Fig. 1.23. Seed processed in German oil mills.
Importance of Fats
27
relatively stable. This is partly a result of the trend to move the mills closer to the large sea harbors, such as Rotterdam in The Netherlands. The quantity of extracted oil has increased because the oil content of rapeseed is higher than that of soybeans. In the processing of soft seeds (rape/sunflower), the Central European mills will thus have greater chances of competition than in crushing soybeans. 1.3.2 Oil Politics in the European Community
At the time when the guidelines of the EC-agricultural policy, which also encompasses the production of oil, were laid down, the degree of self-supply for vegetable oils (except olive oil, which is regulated separately) was ~ 1 0 % and that of vegetable proteins 4%. In the course of the past years, this figure has risen to >50% for vegetable oils (Fig. 1.24). Certain types (rapeseed, sunflower seed) are even exported (Friedeberg 1989). The production is subsidized and protected by duties; in 1962, the EC committed itself in the Dillon-round of the GATT-treaty to not raise the duties on oilseeds, oils, and meals. The subsidies rose from -0.1 billion ECU in 1977 to -3 billion ECU per year in 1988 and have remained on this level. Subsidies were granted without limits on volumes and represented the difference between a representative price on the world market and a desired price (both fixed by the EC-commission for one year). The subsidies are paid via the oil mills. As mentioned above, there are no limits on the acreage and the quantity produced and thus no limits on the total amount of subsidies for an individual producer or, equally, the EC. By changing the targeted price, an incentive to produce oil fruit was
Fig. 1.24. Production of soybeans, rapeseed, and sunflower seed in the European Union.
Fats and Oils Handbook
28
TABLE 1.4 Fatty Acid Composition of Fat in Human Adipose Tissuea and Difference in the Composition of Serum Lipid Extract of Vegetarians and Nonvegetariansb Fatty acid in fat of adipose tissue
(%)
Palmitic Palmitoleic Stearic Oleic Linoleic
25 7 6 45 8
-
All others
9
Vegetarians
Nonvegetarians
Fatty acid (YO) in serum lipids
1982
1986
1982
1986
Palmitic Palmitoleic Stearic Oleic Linoleic Linolenic Arachidonic All others
20.1 3 .O 6.3 19.2 36.5 1.5 5.9 7.5
20.7 3.4 6.6 19.1 34.5 1.1 5.6 9.0
21.1 3.4 6.4 22.3 30.9 1.1 6.3 8.5
22.5 3.7 6.3 22.4 28.4 0.9 5.8 10.0
aSource: Ceigy. bSource: Melchert (1988).
created that led to the explosion of quantities as illustrated above. Friedeberg assumed two motives by the EC-commission for this policy. On the one hand, there was the uneasiness in being dependent on others (low degree of self-supply), supported by a very brief embargo on soybeans by the U.S. in 1973; on the other hand, there was the attempt to reduce the weight of the subsidies on grains, which oppressed the Community’s budget. By means of this policy, the support for the production of oilseeds became the third highest item in the EC’s agricultural expenses. The mawtude of the subsidies unduly burdens both the budget and the relationships to nations TABLE 1.5 Cholesterol Content of Food Food Vegetable oildfats Fish oils Lard Milk Milk powder Butter Milk fat Pork (lean, U.S., UK) Pork (+ fat, U.S., UK) Beef (lean, U.S., UK) Beef (+ fat, US., UK) Calf‘s liver Finfish, low fat Finfish, high fat Shellfish, crustaceans E!% Egg yo1k
Cholesterol (ppm) <50 5000-8000 9 80 120 960 2 800 -3400 >59C-670 >650-710 >650-710 720 4900 470-570 590-790 860-1 200 41 0 16,000-1 7,500
Reference %her 1987 Tucker 1993 Seher 1987 Taufel 1993 Taufel 1993 Taufel 1993 Taufel 1993 Larnbert 1993 Larnbert 1993 Lambert 1993 Lambert 1993 Seher 1987 Childs 1993 Childs 1993 Childs 1993 Taufel 1993 Stadelman 1993
lmportance of Fats
29
with large agricultural exports. In 1988, the U.S. issued a fonnal complaint for the first time concerning the violation of GAIT. As a mechanism of stabilization, the commission proposed a fat-tax, which created quite a stir internationally and provoked the U.S. to threaten counteraction. After great protests by most trading partners as well as by many organizations within the EC, the plans were suspended for the time being. Subsequently, the EC searched for alternative solutions and found a system of “stabilizers,” the elucidation of which would be beyond the scope of this book. It is doubtful that this system will lead to the desired outcome. It is also uncertain how these regulations can be made compatible with Article 110 of the EC-treaty, which states that the aim of the EC’s trade policy is to contribute to the general well being through the following: a harmonic development of world commerce, the progressive lifting of barriers in international trade and the reduction of customs barriers. It is certain that the problems cannot easily be solved, but do seriously threaten the budget. In particular, it is difficiult to make compatible the aims of the EC’s agricultural policy according to Article 39; these include a sufficient income for the farmer, stable (internal) markets, reasonable consumer prices, increased productivity, and a secure supply.
1.4 Fat in Nutrition As previously mentioned, fat serves mankind as an energy supply, a reserve of energy, makes possible the intake of vital fat-soluble substances and supplies the body with essential fatty acids. The fat content of the human body is 16%in the embryo, with an adult body consisting of approximately the same percentage; deviations range from 8 to 50% (FriisHansen 1965). Fat is stored mainly subcutaneously and in the muscular tissue, as well as in deposits surrounding the inner organs such as the heart, kidneys, and intestines. In addition to its function as a quickly activated energy source,the subcutaneously deposited fat also serves as an insulating layer against hypothenria; the fat tissue surrounding the inner organs serves as a protective pad against physical injuries. The body can synthesize fat in part from carbohydrates, but to a large extent it is conveyed with food. The amount of fat in the diet cannot be precisely defined because of the influence of general living conditions (Gottenbos 1985 and 1988). Certain fat components, the essential fatty acids, are vital and must be supplied from outside. They are essential components of the cell membrane structure. Their metabolism is well known (Table 1.6; see Numa 1984, for example) leading to precursors of so-called eicosanoids that influence the behavior of the cell and are important for activities such as proper cholesterol transport. Fat conveyed with food passes through the stomach, is emulsified in the intestine by gall bladder secretions and is then hydrolized by lipases (pancrease), which are the enzymes of the intestine and the pancreas. The lipases present in the stom-
Fats and Oils Handbook
30
TABLE 1.6 Metabolism of Essential Fatty Acids Effect
Enzyme working
a-Linolenic acid ALA (18:3w3)
Linoleic acid (18:2w6) A6-Desaturase
.1
-2 H
Elongase
1
+2c
-1
-2 H
I
+2c
I Docosaheptaenoic acid DPA (22:5@6)
1 Docosa heptaenoic acid DPA (22:5w3j
Adrenic acid ADA (22:4w6) A4-Desaturase
I Eicosapentaenoic acid EPA (20:5w3)
Arachidonic acid AA (20:4w6) Elongase
1 Eicosatetraenoic acid (20:4w3)
Dihomo-y-linolenic acid DGLA (20:3w6) As-Desaturase
1 Stearidonic acid (18:403)
y-Linolenic acid GLA (18:3w6)
-2 H
1 Docosahexaenoic acid DHA (22:6w3j
ach separate fat that is hulled in protein from its protein hull. Hydrolysis is continued in the duodenum to yield ~ 1 0 % of triglycerides and diglycerides as well as 40-50% of monoglycerides, 40-50% of free fatty acids and glycerol. In the first 100 cm of the small intestine, the oily solution of triglycerides and phospholipids (chylomikrons) with a droplet diameter of 0.5 pm exists alongside the microchylons (0.05 pm), which consist of mono- and diglycerides and salts of gall acids. These are further broken down into the micellar fraction consisting of monoglycerides, fatty acids and gall acids. The particle size has then reached -0.005 pm, which is sufficiently small to pass through the intestinal wall. Passage is possible for particles smaller than 0.01 pm (Ludwig 1968). The fat is reconstituted after its components have passed through the intestinal wall (Langdon and Phillips 1961). Short-chain fatty acids can pass through the intestinal wall more easily; however, this is not of importance for healthy people (cf. also Chapter 8.8). The fat enters the body via the lymphatic system, and any unneeded surplus is stored in fat deposits; the remainder is conveyed to the liver metabolism. Fats with melting points 4 0 ° C are virtually completely digestible. For additional information on the metabolism see, for example, Welch (1993). For the nutrition physiology of fats, unsaturated fatty acids are especially important (Hunter 1989). They consist of three families and are characterized by the position of the first double bond of the fatty acid chain, counted from the methyl group. An n-x fatty acid has its first double bond between the xth and x + 1 C-atom of the chain counted from the end. The next double bond is usually situated three C-atoms further along the chain. Representatives of the three main groups are as follows:
Importance of Fats
n-3 linolenic acid n-6 linoleic acid n-9 oleic acid, erucic acid
31
(also 0-3) (also 0-6) (also 0-9)
The hydrolysis of fats is performed by the same enzyme irrespective of the fatty acids. Among unsaturated fatty acids, the enzyme has its highest activity for n-3 fatty acids. In the reesterification after passing through the intestinal wall, the composition of the triglycerides in relation to fat taken in with the food is changed because fats stored in different regions of the body exhibit typical fatty acids patterns. Their composition is relatively constant but can be changed by very unbalanced nutrition or high doses of fat. Human adipose tissue is composed essentially of only five fatty acids (Table 1.4). A considerable portion of linoleic acid must be accumulated in the body because linoleic acid, as an essential fatty acid, cannot be synthesized. The difference becomes visible when comparing the relative fatty acid composition of fat in vegetarians with that in nonvegetarians (Table 1.4). Mammals have the ability to convert saturated fatty acids, but only into those that are monounsaturated, with the location of the double bond only at C-9 (Thiele 1982). This chain can be prolonged toward the carboxyl-end, but not toward the methyl-end. Thus, the synthesis of linoleic acid is not possible in animal organisms (cf Chapter 2.1). In addition to linoleic acid, arachidonic acid (formerly called vitamin F; AaesJorgensen 1961) is also regarded as an essential fatty acid. For about 60 years, it has been known that these two fatty acids are vital (Burr and Burr 1929); for example, they comprise the initial stages of prostaglandins (Bergstrom and Samuelson 1965). Prostaglandins were discovered in sperm by von Euler in 1934, but they are present throughout the body. They are the building blocks of hormones and possess their own physiologic activity as well (hypotensive activity, stimulation of the sleek muscles, regulation of the release of fatty acid from fats). Moreover, essential fatty acids are necessary for growth, contribute substantially to the building of cell walls, and form a structurally essential component of phospholipids. They occur mainly in the brain and nerves and participate in many metabolic processes including those of mitochondria. If the supply of essential fatty acids is insufficient, other nonessential ones are built into cell walls, leading to disorders. Among others, Hansen et al. (1958), Thomasson (1953), Holman (1961), Holman et al. (1964), Aaes-Jorgensen (1966) and Vles and Gottenbos (1989) reported such deficiency symptoms. A deficit of essential fatty acids can result, for example, in reduced growth, lowered prostagladin synthesis and skin damage. The symp toms disappear or come to a halt when n-6 essential fatty acids are supplied. The amount of essential fatty acids (e.g., linoleic or arachidonic acid) that should be present in the diet were previously stated to be at least 2% of the entire calorie supply (Holman 1961), which corresponds to an intake of -2.4 g of linoleic acid4187 kJ (lo00 kcal). The recommendations were developed further, and in more recent recommendations by the FAO/WHO (1977), 3% (corresponding to 3.6 g/4187 kJ or loo0 kcal) is stated as the desirable quantity. This percentage should be increased to
32
Fats and Oils Handbook
during pregnancy and to 5 7 % in the lactation period. According to Adam et a!. (1958), infants should receive twice that amount. Wolfram (1987) surveyed the
metabolic effects of a diet rich in linoleic acid. Another important positive quality of essential fatty acids that is the subject of a growing number of studies is their lipid-lowering quality as well as their ability to exercise a favorable influence on an excessive cholesterol level in the blood. This has a special significance for health issues because both an increased lipid level and an increased cholesterol level are considered to be risk factors for heart attacks. Cardiovascular diseases are the number one causes of death in industrial nations throughout the world. The lowering of lipid levels as a precautionary measure has been known for more than 30 years (Ahrens 1957 and 1959, Groen et al. 1952, Kinsella et al. 1952); although it is undisputed among experts, it is repeatedly attacked by lobbies. Mertz (1983) conducted a survey of the current state of knowledge. These findings on the connection between cholesterol levels and cardiovascular diseases were supported by the awarding of the Nobel Prize for medicine in 1985 to Brown and Goldstein, who were pioneers in the studies on this subject. Arteriosclerosis, caused by cholesterol esters and elevated cholesterol level, has clearly been identified as one of the key risk factors for heart disease (LRCCPT 1984, Schlierf 1986). Today, a distinction is made between LDL (low-density lipoprotein), commonly labeled “bad cholesterol,” and HDL (high-density lipoprotein), which is considered “good cholesterol.” HDL is responsible for transporting surplus cholesterol from the body to the liver. Thus it represents a means of transportation. A high level of LDL is directly related to heart disorders. A survey of the influence of nutrition was given by Schettler (1984). The lowering of the cholesterol level is due to the direct supply of linoleic acid and to its relative quantity in the fat. Stamler (1966) showed that when raising the intake of polyunsaturated fatty acids from 9 to 15%, the amount of cholesterol in the blood serum decreases by only 1.2 mg/mL. When the supply of saturated fatty acids is reduced from 16 to 9%, which indirectly results in a relative increase in polyunsaturated fatty acids, the amount of cholesterol in the blood serum drops by 1.9 mg/mL. The fundamental factor is not the amount per se of polyunsaturated fatty acids, but the proportion between them and the saturated fatty acids. This proportion is also called the P/S ratio (P = polyunsaturated fatty acids, S = saturated fatty acids). According to Mertz (1983), the P/S factor in the food of the German population was 0.39. This is far below the desirable ratio of 1:1 (P/S = 1). As a consequence (e.g., for diet margarine), the legislature will probably abandon the exclusive specification of the content of linoleic acid in the declaration of diet products and require in the future that the portion of saturated fatty acids or the P/S quotient be stated. It is doubtful that reaching the positive effects of a higher P/S ratio as stated above through increasing the supply of linoleic acid to the diet will be achieved, especially considering the rivalry between margarine and butter. This is mainly a problem of agricultural politics (cf. Chapter 1.3) and not one of health politics. The fact that it is not the‘ origin of the fat (vegetable or animal), but rather the P/Sratio that is crucial
lmportance of Fats
33
is often neglected. The P/S ratio of butter is 0.05; that of vegetable coconut fat only 0.02. However, in spite of its vegetable origin, the latter is not considered suitable as an exclusive fat for healthy nutrition. The quantities consumed are low because it is not a basic food but one found only in specialty products. Sunflower oil, on the contrary, is especially suitable (P/S = 5.82;Wirths 1981). Its P/S ratio is so high that the sunflower oil can compensate for higher saturated fatty acid intake in the normal fat supply. More recent analyses led to the recommendation to adjust the proportions of polyunsaturated fatty acids, monounsaturated fatty acids and saturated fatty acids (PUFAIMUFAISAFA) to 1:l:l (MI3 1984). These findings do not call into question prevailing nutrition recommendations regarding linoleic acid as an essential fatty acid. Findings in this area have not changed. However, a stronger positive (lowering) influence of the monounsaturated acids (i.e., predominantly oleic acid) on the cholesterol level than estimated has been found. Oils rich in oleic acid (e.g., rapeseed oil, olive oil) can thus be suitable for a cholesterol-reducing diet as well as those with a high PUFA content (e.g., sunflower oil; see, for example, Laasko et al. 1989). However, because the invisible fats are rich in saturated fatty acids, diet margarines should have a content of saturated fatty acids ~ 2 0 % in order to reach the targeted proportion. Altogether, science today is able to correctly predict the average change of the cholesterol level in the blood when nutrition is changed. Findings to date led the U.S. Federal Health Agency (NIH 1984) to recommend that Americans should reduce their present intake of 40% of calories from fat in their diet to 30%. Moreover, they should limit the intake of saturated fatty acids to ~ 1 0 % of the calorie intake and raise that of polyunsaturated fatty acids to 10%of the calorie intake (but not more). The daily intake of cholesterol should be limited to a maximum of 25&300 mg. The European Consensus-Conference (1986) adopted the American values in their recommendations and added maximum values for the therapy of high-risk persons. (Schwandt 1987). The European Arteriosclerosis Society required further measures (Assmann and Schettler 1987). When examining the cholesterol level, it is essential to take into consideration the intake of the cholesterol itself. An important source is animal products, especially animal fats, which typically contain substantial amounts of cholesterol (Table 1.5). According to a general agreement derived from British legislation, substances with 4 0 ppm are regarded as cholesterol free. Vegetable oils not only have the advantage of reducing cholesterol levels, but they also do not add to the intake of cholesterol (Seher 1987). Thus, with an elevated cholesterol level, nutrition with the correct fat must be balanced with a suitable nutrition plan. Proposals were made to shift the P/S factor in the direction of one, but only sick and high-risk people need to take special care. At present, there are efforts to remove cholesterol from butter to avoid at least one of its detriments (extraction with supercritical COz, Kankare and Antila 1989). The findings in the cholesterol debate were surveyed by Goldberg and Schonfeld (1958), Grundy (1986), and McGandy and Hegsted (1973, among others.
34
Fats and Oils Handbook
Knowledge about the disadvantages of animal fats has continually led to attempts to reduce their presence by changes in animal feed (Leaf and Weber 1988). This applies particularly to the feeding of milk cows. It was possible, for example, to raise the content of n-3 fatty acids in milk fat to 6% by mixing fish oil (Menhaden oil) into the fodder (Hagemester 1989). The passage of the n-3 fatty acids from the fodder to the milk fat was between 35 and 40%. In this special instance, such milk fat is preferred to conventional milk fat from the point of view of nutrition physiology. However, it is uncertain whether it will provide a reasonable alternative considering the conversion factor mentioned above. For about 20 years, nutritionists have concentrated on n-3 fatty acids (a-3 FA), because Bang and Dyersberg (1975) observed that the Greenland Eskimos, in spite of their extensive consumption of fat, suffered less from heart disease than the Danes. Their biochemical values were very close to those of a Japanese population of fishermen, who also subsisted mainly on marine animals (Yamori et al. 1985). The Eskimo diet (marine oils) is rich in n-3 fatty acids. In marine oils, n-3 fatty acids are almost exclusively long-chain acids. It is estimated that the required daily quantity of these fatty acids is 0.2% (Benadt 1988). The daily intake with Western food is -1 g of n-3 fatty acids. Investigations concerning the advantages and possible disadvantages of these acids have not yielded any conclusive results to date and are still in progress. However, studies in Europe indicate (Kromhout et al. 1985, study in Zutphen, The Netherlands) that there is a connection. There appears to be definitive evidence that the daily consumption of n-3 fatty acids must exceed an average of 2 g to achieve an effect (Driss and Darcet 1988); this is equivalent to daily consumption of the relatively high amount of 200 g of fish. Findings are not sufficiently advanced to recommend the intake in concentrated form, e.g., in capsules, or to incorporate such fatty acids into fat products. Moreover, the quantity that would then have to be used to ensure the effect is rather high, although their efficiency is 20 times higher than that of linoleic or linolenic acid (Singer). It is also questionable whether a continuous nourishment with foods rich in n-3 fatty acids could be harmful. A survey of the state of the discussion about fatty acids from fish oils was given by Harris (1989). The concern that polyunsaturated fatty acids may be susceptible to oxidative damage and might develop into carcinogenic substances within the body is repeatedly expressed by scientific outsiders, but is unfounded. Dormandy (1983) determined that in-vivo oxidation of fatty acids does not take place. Within the body, as in the intact seed, they are protected by the body’s antioxidants. The consumption of fats oxidized (peroxides) by inappropriate handling is also not dangerous. Fats containing harmful concentrations of oxidized fatty acids are not edible as a result of their very bad taste. The fat supply itself constitutes another problem. Fat consumption in the industrial nations today satisfies between 35 and 45% of our energy demand, and in the developing countries between 10 and 20%. The worldwide consumption of fat during the mid-1970s was 12.5 kg per capita per year. In Germany, for exam-
lrnportance of Fats
35
ple, more than three times that amount of fat was eaten. The level of fat consumption parallels the rise in standard of living. Thus, the consumption of animal and vegetable fats and oils in the U.S. more than doubled between 1950 and 1985 (Hammond 1988). In contrast with Germany, however, there was a strong shift to vegetable oil consumption. This is disquieting in two respects. As a rule, the intensity of physical labor decreases as the standard of living rises. Recommendations for the daily intake of calories are as follows: 2000kcal 2300 kcal 3200 kcal
(8370k.l) (9620 k.l) (13390 k.l)
for light work, for medium work and for hard work.
This would mean that even a constant consumption of fat would be too high, because surplus energy is conveyed to the body. On the other hand, fat consumption is rising because fat makes food tastier. It is recommended that calorie demands met by fats in the diet range between 25% and a maximum of 35%. Adding to this negative trend is the fact that much of the fat in foods is in the form of hidden fats. Hidden fats are fats contained in other foods and consumed unconsciously. This applies especially to meat, sausage, and cheese (c$ Table 1.2). Studies in the Federal Republic of Germany in 1982 showed that >50% of the fats consumed was in the form of hidden fats. In addition to the fact that the population is not aware of which foods contain what quantities of fat, it becomes increasingly more apparent that the predominant part of hidden fats consists of animal fats with a high proportion of saturated fatty acids. In this manner, the P/S quotient is lowered (which is negative), and no essential fatty acids are consumed. When the calorie supply is reduced, which usually occurs by lowering the amount of visible fats, the negative tendency is further intensified. Attempts to exchange the saturated fats in foods for highly unsaturated ones are constantly thwarted by protectionist legislation (c$ Chapter 1.5). Greater freedom remains unattainable as a result of the harmonization of the respective laws and regulations within the European Union. Besides the fat-associated substances, minor components are important as well. Some of these have negative effects but are found only in the grain; in that case, they cannot be used as feed for all animals. Experiments have shown that gossypol from cottonseed causes pathologic changes in the testicles of mammals that can lead to sterility (Berardi and Goldblatt 1980, Xue 1980). For this reason, it was tested in China as a contraceptive for males. Its effect is attributed to the generation of oxygen radicals. Refined cottonseed oil does not contain gossypol, thus the attention is directed exclusively toward cotton grain. Fat-soluble vitamins have considerable positive influences. Vitamins A and the family of carotenes possessing vitamin A activity, as well as vitamins D and E, are fat-soluble and water-insoluble substances. Consequently, these substances occur together only with fat, i.e., they can be conveyed to the body only via fat-containing
36
Fats and Oils Handbook
food (Sebrell and Harris 1954). Vitamin A is necessary for regular growth, normal eyesight and procreative capacity. Moreover, it plays an important role in the stability of the cell membranes. Vitamin D ensures the correct calcium level in serum and is necessary for the normal growth of bones. Vitamin E protects vital substances such as unsaturated fatty acids, vitamins A and D, as well as thiol groups in enzymes from oxidation (c$ Chapter 2.2). In contrast to the essential fatty acids, vitamins occur in animal and vegetable fats, although vitamin E is present in larger quantities only in vegetable fats. Thus, with a normal food supply, deficiency is not an issue. Vitamin E represents one of the essential radical scavengers in lipid membranes (Pryor 1976). It was applied in clinical trials to combat illnesses caused by oxidation processes. These trials were rather successful (Bieri et al. 1983). A protective function towards DNA was observed (Beckmann et al. 1982), as was greater endurance in test animals (Davies et al. 1982). Other experiments suggest that vitamin E has anticarcinogenic effects as well (Wang 1982). p-Carotene also has antioxidant effects. It intercepts singlet oxygen, which has a strong mutagenic effect as a result of its high reactivity (Foote 1988, Krinsky and Deneke 1982). Experiments have also shown a protective function against the development of cancer (Mathews-Roth 1982, Rettura et al. 1983). A survey of the multiple fields of applications was made by Ames (1983). It is assumed that fatsoluble vitamins are helpful against oxidized metabolites of cholesterol that were observed to contribute to the development of heart disorders (Yagi et al. 1981). Apart from the anticarcinogenic effect of some of the minor components in fats, studies reporting a direct correlation between the fat intake and the frequency of breast and colon cancer continue to appear (Doll and Pet0 1981, Fink and Kritchevsky 1981, Kinlen 1983, NRC 1982). To date, it has not been possible to establish a direct connection. However, there seem to be more indications that the frequency of cancer generally rises with caloric intake. Only in this connection could fat be a role-playing factor.
1.5 Fats and Oils in Legislation The legislation in effect for this branch of industry applies to the products, thereby directly affecting the consumer and producer. The legislation also applies to the production process. 1.5.1 Product-Related Legislation
Many foods are narrowly defined by laws and regulations concerning their composition, mode of production and qualities. Not everything can (or should), however, be regulated by laws. In addition to legal directions, certain modes of behavior (principles of the responsible producer, good manufacturing practice) have emerged and various codes have been formulated, e.g., the Codex Alimentarius of the FAO, and the Leitsatze des Deutschen Lebensmittelbuches (Guiding Principles of the German Food Book) is an example for Europe. These guiding principles are
Importance of Fats
37
not legally binding but are consulted to define honest trading practice and are the foundations of legal decisions in case of controversy. In many cases, they fill the gaps where neither laws nor special regulations exist or give specifications which exceed legal limitation or description. In principle, there can be two motivations for product-related legislation in the domain of food, i.e., the protection of the consumer and citizen and aspects of economic policy. The protection of the consumer can include matters of health, but also protection from fraud. Aspects of economic policy might include emergency situations (war/postwar), partial attempts at selfsufficiency, or the preservation of an agriculture that is no longer competitive under the conditions of the world market. Concerning health risks, the protection of the consumer is always foremost and falls under the duties of the state within the obligation of public care. Frequently, however, the extent and the character of the measures to be taken are under discussion. Fats and oils, as such, fall under the common rules on maximum values of environmental pollutants. In contrast, there are very detailed rules for the products described in Chapter 8 (butter, margarine and mayonnaise). Legislative interventions motivated by health policy in the field of oils and fats have rarely occurred. An example is the regulation regarding the maximum content of erucic acid; however, this has been rendered superfluousby the cultivation of new types. For ingredients, processing aids, and additional substances, there are two basic approaches. One is that all substances that are not deemed harmful can be admitted, and consequently, harmful substances are prohibited or restricted in their quantity. The other is that everythrng that is not explicitly allowed is prohibited. The EC follows the second principle in many fields (regulation about the admission of food additives). This is a policy motivated by a desire for control rather than one of protection from danger, a fact that becomes immediately obvious when questioning why an ingredient is prohibited in one food but allowed in another. With few exceptions, one and the same substance cannot be at once both harmful and harmless. Trade policy is aimed primarily at the protection of agriculture. Due to their structure, the European States are not able to offer all agrarian products at world market prices. Therefore a certain protection is advisable to maintain at least partial independence.It must be considered, however, that excessive protection also prevents the seizing of opportunities. Legislation usually intervenes in times of emergencies. This happens primarily by means of regulations or guiding principles. Even more so than laws, guiding principles are a mirror of their times. During World War 11, they gave reliable information about the supply situation in Germany because regulations were in each case adapted to it. Thus, according to the German guiding principles for mayonnaise of 1941, salad mayonnaise, for example, had to contain only 20% oil instead of 50%, and milk and fish protein were allowed as substitutes for egg yolk. 1.5.2 Production-Related Legislation
In the production of oils and fats by means of mechanical or solvent extraction, in their processing or refining, and in the making of products containing fat, the producer
Fats and Oils Handbook
38
is subject to many general legal regulations concerning emissions or sewage, for example, but also to several highly specialized injunctions. These directives can differ widely depending on the location of the business, and even within one country from community to community. Dealing with these regulations in a detailed way and on a universally valid basis is possible but would exceed the scope of this book.
1.6 Fats as Industrial Raw Materials A relatively large portion of edible fats and oils is utilized for industrial purposes
(not nutrition). Often batches that do not comply with the strict demands for foodgrade raw materials are used for this purpose. Worldwide, the production of oleochemicals is -9-10 million ton (Seidel 1983), and a wide range of products is produced (Fig. 1.25). For some oils and fats, the portion not used for nutrition is considerable (Table 1.7). In 1981, after a continuous rise since the first energy crisis in 1973, the price of the raw material ethylene had climbed beyond that of soybean, coconut and palm oils, and tallow (Fig. 1.26). At that time, large chemical companies tried to secure their position by acquisitions that would provide a position in this raw material market. In the meantime, ethylene prices have fallen again. This interest was also motivated by a desire to remain in the market and exert influence on the types of new crops cultivated exclusively for the food industry. Erucic acid is relatively easily modified chemically. With the transition to rape OillFat
Olymml Resins EmulabIan C e i l U I o ~produdion o i for n ~ ~POlyOlS mineral oil produdion CosmsUcs Glymml Eaten Detergents
Auxiliary ~
Fatty h i n o s
Fatty Alcohols
Fatty Amldes
Adddiws for coal flotaUon Anti mnorives Sufladsntr Emubifiers
Esters with polyethybnglycd Fabric deanen Non-ionogenic emuI8hien
Detergents Emutsifien Fire extinguishen
Animal feed soaps Chemicsb fcfthe mineral oil and rubber industry
Fig. 1.25. Simplified flowchart of oleochemicals production.
Importance of Fats
39
TABLE 1.7
Uses of Vegetable Oil for Nonfood Purposesa Oil type and nonfood usage (YO) 0.25
Soybean oil Palm oil Palm kernel oil Rapeseed oil
10 10 40
Coconut oil Castor bean oil Linseed oil Tung oil
55 100 100 100
Type of usage (% of total nonfood usage) 36
Fatty acids Animal feed Soap Other
29 15 13
Paints Lubricants Polymers
3 2 2
aSource: Pryde and Rotfus (1 989).
species with low erucic acid content, the chemical industry was robbed of an important raw material. From then on, the prices for a low tonnage of rape with a high portion of erucic acid (HEAR) were above those of LEAR oil. Today crambe oil, which also possesses 55-60% of erucic acid, is considered to be a replacement for HEAR. Mustard seed oil can also be used. Taken as a whole, the production of raw materials in fat chemistry has developed from synthetic to natural raw materials, and this trend is continuing (Table 1.8). 70
-
.
0
Fig. 1.26. Price relation between soybean oil and ethylene.
Fats and Oils Handbook
40
TABLE 1.8 Oleo Chemicals and Their Raw Material Sourcesa Fatty acids
Amount (1 OOO ton) YO Natural YOSynthetic
Fatty alcohols
Glycerol
Fatty arnines
U.S.
Europe
U.S.
Europe
U.S.
Europe
U.S.
Europe
lo00
650
160
195
350
210
110
64
98 2
99 1
57 43
72 28
16 84
37 63
85 15
100 0
dSource:Seidel (1 983).
1.7 Fats and Oils as a Source of Energy In the course of history, it has been demonstrated repeatedly that fats are suitable as a source of energy. Rudolf Diesel had already determined that his engines could run on edible oil. As early as 1900, a Diesel engine powered by peanut oil was shown at the world’s fair in Paris (Nitske and Wilson 1965). However, the true potential of renewable raw materials may lie not in the combustion of the oils known today but in the utilization of new species. When we compare the qualities of vegetable oils with Diesel fuel, we notice that the caloric value is -10% below that of Diesel oil (Table 1.9). Among renewable raw materials, vegetable oils exhibit the most favorable relation between energy yield and energy investment (Table 1.10).Because vegetable oils have always been used in part as a source of energy, the idea is not new. However, the demands on the oils for use in modem engines have changed compared with those for illumination purposes. A study by Apfelbeck (1988) shows which fuel parameters must be met for today’s vehicles (Table 1.11). When comparing the prices for Diesel and soybean oil, we see that for the time being, there is no point in using edible oils and fats for combustion purposes. TABLE 1.9 Comparison of Diesel Oil, Rapeseed Oil, Sunflower Oil and Their Methyl Esters Sunflower
Caloric value (MJ/kg) Density (dcrn) Viscosity (cP,20°C) Cloud point (“C) Flash Point (“C) Ash (Yo) Sulfur (YO) Sulfur (rnol%) Reference
Diesel oil
Crude oil
Methyl ester
4246 0.835 3.9 -0.6 50-77 0.01 -0.27 -0.1 4 Shell
39.28 0.925 34.7 -6.6 215.5 0.04 0.1 2
40.16 0.880 4.22 0-1 183
-
-
0.01
-
Quick 1989
Rapeseed Crude oil
36.7-37.7 0.91-0.92 68-97.7
-
Methyl ester
37.02-37.20 0.86-0.90 6-9
-
31 7-324 1 1 1-1 75 <0.01-0.5 <0.01-0.05 0.009-0.01 2 0.002-0.006 Bundesurnweltamt 1993
41
importance of Fats
TABLE 1.10 Energy Balance from Renewable Source9 Source
Energy balance investdyielded
Energy yield net ( a h a )
2.8 2.7 2.5 1.3 1.1
43.3 37.9 58.9 18.4 5.2
Sunflower oil Rapeseed oil Ethanol from sugar beets Corn Wheat a%urce: Pernkopf (1984)
TABLE 1.11 Requirements for Fuel Ester9 Free fatty acids Mono-, diglycerides Glycerol Methanol Water Metals (each)
<0.2% <0.1 Y o
=%Source: Apfelbeck (1988)
In this comparison, it has to be considered that in Europe, taxes constitute the largest portion of the price for vehicle fuels. The U.S., with its much lower taxation rate, thus presents a better opportunity (Fig. 1.27). Considering the respective quantities, it becomes obvious that vegetable oils could cover only a small fraction of the demand. Consequently, greater utilization would lead to a considerable shortage of oils for consumption, and thus to rising prices. In spite of these rather poor prospects of finding an economically viable alternative to mineral oil fuels in today’s vegetable oils, experiments partially supported by the German Federal Department of Research and Technology are underway under strictly controlled circumstances to determine the behavior of Diesel engines suited for rapeseed oil (Anonymous 1988). Although experts such as the Federal Agency for the Environment released a study concluding that this route is not viable, new plants have been built. In Austria, for example, more than 10 plants had already been erected; only one is currently still operational at a low level. Even if a redistribution of the subsidies is effected to support these projects, they can hardly be successful given the current low price for mineral oil. The fanners’ associations stated that in 1990, 80% of the arable land of the Federal Republic of Germany would suffice for the production of food. For inactive areas, subsidies of 700-1440 German marks subsidies per hectare are paid currently. Cultivated with rape, these areas would suffice to meet 3 4 % of the annual
Fats and Oils Handbook
42 70 60
.
ziu d
g40 v)
2. 30 8
!5
20
10
0
Fig. 1.27. Price relation between diesel oil and soybean oil in the US.
demand for fuel oil or 10-12% of the demand for Diesel oil (Stover 1988). However, this could be done in a reasonable way only with smaller, decentralized, simple oil mills (delivery by the farmers themselves). Because larger amounts of fat remain in the meal in such mills (pressing only, without preliminary treatment of the seed), higher prices for meal would have to be charged for the process to be economical. This might indeed be possible because such meal has a better value as fodder in terms of energy supplied, but it is doubtful whether the market would honor it. Altogether, this scenario is interesting, but inefficient for the time being. As an example of oil fruits that are not currently in use, a research project conceming the purge nut can be examined. The purge nut is a spurge plant and grows even in tremendous heat and in the poorest soils. The nut was rediscovered by scientists of the Society for Technical Cooperation at the Western tip of Africa. (DPA 1987). An engine powered with its oil ran successfully during a long-term trial. The oil was described as early as 1830 by Geiger, who used it as a laxative. According to scientists, the nut can be used as a raw material for soap production, as a source of energy, and as a supplier of raw chemicals. New raw materials can change the situation, although considerable costs must be expected when deriving the fadoil Erom the raw materials; the chances of commercialization are low at present, considering the present supply of mineral oil on the world market. Another interesting opportunity is to make use of deserts or semi-deserts by growing plants at a very low density and to organize the cultivation effectively over the entire area that remains otherwise unused. However, suitable plants have not yet been found. With an insufficient oil content, used-up auxiliary substances and garbage removal pose sigmficant problems.
importance of Fats
43
1.8 New Sources of Raw Material New sources of raw materials can open up in two different ways. It is possible to use new crops for oil supply, especially for industrial use. In addition, it is feasible that new plants can be adapted to new requirements by means of cultivation or by genetic modification. More recent contributions to this discussion (e.g., Richtler and Knaut 1991) cover the entire ecological balance in their reflections, for example, the CO, balance, and as a result, new aspects might emerge. 1.8.1 New Plants Through Plant Breeding or by Genetic Modification
The possibility of modifying plants by means of cultivation is virtually unlimited. All types existing today have been generated via a selection process that has lasted for centuries. However, with today’s technology, it is possible to accelerate this selection mechanism or even to “construct” plants within certain limits. A very good example for the conventional cultivation of an oil plant with new qualities is the “Double-Zero-Rape.’’ First, the fatty acid composition of this type of rape was modified in such a way that it contained (virtually) no erucic acid; then, bitter glucosinolates were removed by cultivation to make the meal more suitable as animal feed. Plans to remove gossypol from cottonseed by cultivation proceed in the same direction. It would make this oil type more applicable, because here, too, the use of the meal could be optimized. However, changing the composition of fatty acids can have other objectives as well. By ingeniously cultivating and blending the raw materials, the amount of oil that has to be modified could be reduced considerably. In the most favorable case, oils with ideal compositions could be processed into products directly from the oil mill. Opportunities lie in the cultivation of types with such an amount of saturated fatty acids that hardening is no longer necessary. An ideal distribution of fatty acids in the triglyceride can make interesterifkation obsolete. Additionally, new plants may yield qualities that render refining at least partially superfluous. Many other improvements are conceivable, but most of them will be achieved in a reasonable time only by means of gene technology. Whether this technology will be accepted by the public-at least in Europe-is doubtful. Achieving these aims would reduce production costs and improve the image perceived by the consumer Species of safflower that possess oil rich in oleic acid already exist; the same is true for sunflower types that contain >80% oleic acid (US.Patents 4627192, 1986, and 4743402, 1988). With increasing frequency, these cultivars are covered by patents, so that efforts of the growers become more interesting on a commercial level. In Canada, rape already provides >50% of the raw materials for margarine. The disadvantage of rapeseed oil is its relatively high content of linolenic acid. Here also, the cultivation of a species with a linolenic acid content ~ 3 % has been successful (Allelix Crop Technology, Canadian Patent 1989). In the new species, linolenic acid is almost completely replaced by oleic acid. The same problem exists for soybeans. Cultivars of soybeans with a low concentration of linolenic acid have been successful. Species with a higher concentration of stearic acid were also found.
Fats and Oils Handbook
44
In Chapters 1.4 and 4.3.2, gossypol is mentioned as an undesirable ingredient of cottonseed. Cotton that lacks gossypol-capsules has been cultivated successfully. However, the problem is not yet entirely solved because the new plants or rather their seeds are very vulnerable to infestation with AspergiZZusJuvus (cf.also Chapter 4.3.11; Campbell 1983). Among others, Rtibbelen and Hirsinger (1982 and 1987) reported on methods applied today to create tailor-made plants; more examples are given in Chapter 4.
1.9 Fat Substitutes It has been known for a long time that people in the industrial nations consume too much fat. The main reason is that fat is an excellent carrier of flavors; its physical qualities make food smooth, thereby increasing the pleasant taste considerably. Compared with other food ingredients, fat has more than twice the caloric content. Thus, in the attempt to limit the caloric supply, reducing the intake of fat has the strongest effect (per unit of weight). For these reasons, there have been attempts to find substitutes with reduced or zero caloric value. This is much more difficult than finding a substitute for sugar, because the applications of fat deviate strongly from those of sugar. Saccharin was found early on and later Cyclamate, and some years ago, Aspartame and Acesulfam. Attempts to find a substitute for fat culminated at the end of the 1980s. LaBarge (1988) named the main classes of substances that might serve as lowcalorie oils and as substitutes.These include the following: combinations of water and surface active substances (surfactants), including special proteins and polysaccharides with absorption capacity, compounds such as acetoglycerides and medium-chain triglycerides with a reduced caloric value, compounds that deviate considerably in structure from triglycerides, such as paraffin and silicone, compounds without calories with fat-like qualities, produced mainly through modified ester bonds, e.g., fatty esters of polysaccharides. Only in 1929 did Channon and Collison produce the first reliable study concerning the absorption of fats in the body. Strycker (1941) and Deuel(l948) compiled extensive material by feeding rats. After these experiments indicated which substances are not resorbed, research could be directed systematically. 1.9.1 Carbohydrates
There are some products on the market that could replace fat in their applications. As a rule, they can be used only in low-temperatureapplications and those in which fat is employed to reach a good, smooth texture. They are not suitable as a heat transmitter in roasting and frying. Also, they do not develop the respective flavors. Their primary
Importance of Fats
45
effect is to absorb water and give a smooth feeling in the mouth. Examples of such products are polydextrose (Pfizer), which, however, can have a laxative effect, N-Oil (trademark of National Starch Co.) or maltodextrine. Vogt (1987) demonstrated the qualities of a fat substitute based on starch, i.e., enzymically modified potato starch that can be used in place of fat in such foods as stuffings or milk products. 1.9.2 Polycarbonic Acid Esters
Hamm (1984) conducted experiments on polycarbonic acid esters as a fat replacer for margarine and mayonnaise. Margarine was produced with trialkoxy carballylate and jojoba oil (LaBarge 1988). With jojoba oil, however, margarines were not convincing. Trialkoxytricarballylate (TATCA) showed excellent qualities, but failed in the animal-feeding tests conducted to date. 1.9.3 Polyglycerol Esters and Ethers
Polyglycerol esters can easily be produced (Babayan 1968, Mcintyre 1979), but in feeding tests, it did not appear that the caloric value was lower than that of triglycerides. These substances were also not well suited for baking (Babayan 1982). Instead of triglyceride esters, triglyceride ethers can also be synthesized. Several patent applications have been submitted. 1.9.4 Proteins
In 1988, “Simplesse” (trademark of NutraSweet), a fat substitute based on protein was announced by the NutraSweet company. Simplesse is produced by decomposing long-chain proteins into small pieces of -0.001 mm in diameter. The pieces are so small that 50 billion fit on a teaspoon (Wagner 1988). The small particles exhibit the same creaminess as fat, deceiving the taste organs. The sensory sensation of creaminess is actually not related to classes of substances like triglycerides, as was believed for a long time. It is due to particle size and shape. Simplesse is a protein and therefore all applications involving strong heating are impossible. Because its effect is based on a deception of the tongue, Simplesse can be applied only where fat creates a creamy impression in the products. In 1989, NutraSweet intended to introduce Simplesse without examination by the FDA, claiming that it is a food only in “shredded” form. The FDA, however, insisted on a procedure for its approval, which required some time. In the meantime, Simplesse is on the market. 1.9.5 Sucrose Polyesters (SPE)
In the 1950s and 1960s, the basic work for the application of sucrose polyesters had already been done by Rizzi and Taylor (1976). They esterified methyl esters of soybean oil fatty acids with sugar. For synthesis, potassium salts of the fatty acids are formed and are converted with the aid of sodium hydride. Volpenheim (1985)
Fats and Oils Handbook
46
received a patent for replacing sodium hydride with potassium carbonate. For the time being, SPE are the only fat substitutes that can replace fat in practically all applications. Because of their good heat stability, they can also be applied in areas in which the above-mentioned substances fail. In the literal sense, they are simply “fat substitutes.” A major obstacle to their introduction was that SPE have a strong laxative effect when a certain quantity is consumed. Procter and Gamble announced that the problem could be solved by adding an antidote. Meanwhile, the problem has been solved without such an antidote. In addition to Procter and Gamble, Unilever, Mitsubishi, and Dai-Ichi have also worked on SPE (LaBarge 1988). The initial patent held by Procter and Gamble expires in 1998, but will most likely be prolonged by increasing numbers of new patents concerning particular procedures for production. Bernhardt (1988) described the production (Fig. 1.28). Instead of the three fatty acids esterifled to glycerol, sugar is able to bind eight fatty acids. In SPE,the sugar contains six, seven or eight fatty acids, because complete esterifcation of all hydroxyl groups has not yet been successful. SPE are miscible with fadoil and insoluble in water (Mattson 1976). They cannot be resorbed by the body because the body does not possess enzymes to split them. A survey of the possibilities of application, advantages and problems of SPE was made by Toma et al. (1988). When this book was edited in German, the question whether SPE (termed Olestra by Procter and Gamble) could be introduced depended mainly on whether legislative authorities (FDA, Food and Drug Administration, BGA, Bundesgesundheitsamt/ FaffOil
I
Esterriinl,
]
<<< Methanol <<< ~
>>> G cerol
Fatty acid methyl ester
,
Neutralization
I
Bleaching
I
I
Deodorization
I
SPE (fully refined)
Fig. 1.28. Flow chart of SPE production.
Importance of fats
47
German Federal Health Agency) would license it. Licensing is necessary because, according to the prevailing definition, SPE is not a food, but rather a food additive. Licensing had been applied for at the FDA in 1988. Meanwhile Olestra (trademark of Procter and Gamble) has been approved for a certain range of snacks. Application in Europe is still doubtful. 1.9.6 Polymeric Siloxanes
Polymeric siloxanes as well as substituted phenyl-methyl-polysiloxaneswere also investigated as possible fat substitutes. The experiments were conducted at the Institute for Human Nutrition at Michigan State University and did not show any side effects in rats. Experiments in kitchen applications (e.g., frying) were conducted by Zabik (1987 and 1989) and Morehouse (1987 and 1989) and gave satisfying results. The FDA has not yet approved these substances. 1.1 0 References Aaes-Jorgensen, E., (1961) Essential Fatty Acids, Physiol. Rev. 41, 1-5 1. Aaes-Jorgensen, E., (1966) Unsaturated Fatty Acid Isomers in Nutrition, Nutr. Rev. I , 24. Adam, D.J.D., Hansen A.E., and Wiese, H.F., (1958) Essential Fatty Acids in Infant Nutrition 11. Effect of Linoleic Acid on Caloric Intake, J. Nutr. 66, 555. Ahrens B., (1957) The Influence of Dietary Fats on Serum Lipid Levels in Man, Lancet I, 943.5. Ahrens, B., The Effect on Serum-Lipids of a Dietary Fat, Highly Unsaturated, but Poor in Essential Fatty Acids, Lancet I, 115 (1959). Ames, B.N., (1983) Dietary Carcinogens and Anticarcinogens-Oxygen Radicals and Degenerative Diseases, Science 221, 1256-1264. Anonymous, (1988) Rapsol als Treibstoff, Chemische Rundschau 40, 10. Anonymous, (1987) Malaysia Defends Palm Oil, Food Manufacture Int. SeptJOct., 10. Apfelbeck, R., private information to Stover 1988, citation from Stover see below. Assmann, G., and Schettler, G., (1987) Ein Strategie-Konzept der Europaischen Arteriosklerose-Gesellschaft: Die Pravention der koronaren Herzerkrankung, Deutsches Arzteblart-Arztliche Mitteilungen 84, 45-48. Babayan, V.K., and McIntyre, R.T., (1968) Preparations and Properties of Some Polyglycerol Esters of Short and Medium Chain Length Fatty Acids, J. Am. Oil Chem. SOC.48, 307. Babayan, V.K., and McIntyre, R.T., (1982) Polyglycerol Esters: Unique Additives for the Bakery Industry, Cereal Foods World 27, 510. Bang, H.O., and Dyersberg, J., (1975) Haemostatic Function and Platelet Polyunsaturated Fatty Acids in Eskimos, Lancet 2, 433-435. Beckman, C., Roy, R.M., and Sproule, A., (1982) Modification of Radiation-Induced SexLinked Recessive Lethal Mutation Frequency by Tocopherol, Mutat. Res. 105, 73-77. BenadC, A.J.S., (1988) Editorial Comment: Essential Fatty Acids, SA Tijdskrift voor Voedselwetenschap en Voeding I , 2. Berardi, L.C., and Goldblatt, L.A., (1980) Toxic Constituents of Plant Foodstuff; in Toxic Constituents of Plant FoodstufJ; (Liener I.E., ed.), pp. 183-237, Academic Press, New York.
48
Fats and Oils Handbook
Bergstrom, S.,and Samuelsson, H., (1965) Prostaglandins, Annu. Rev. Biochem. 101, 34. Bernhardt, C. A,, (1988) Olestra-A Non-Caloric Fat Replacement, Food Technol. Int. Europe 176. Bieri, J.G., Corash, L., and Hubbard, V.S., (1983) Medical Uses of Vitamin E, N. Engl. J. Med. 308, 1063. Burr, G.O., and Burr, M.M., (1929) A New Deficiency Disease Produced by the Rigid Exclusion of Fat from the Diet, J. Biol. Chem. 82, 345-367. Campbell, C., personal information to Ames B.N. (1983), citation from Ames see above. Channon, H.J., and Collison, G.A., (1929) The Unsaponifiable Fraction of Liver Oils. IV. The Absorption of Liquid Paraffin from the Alimentary Tract in the Rat, J. Biochem. 23, 676. Childs, M.T., (1993) Fish, Dietary Importance of Fish and Shellfish, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 1879, Academic Press, London. Davies, K.J.A., Quintanilha, A.T., Brooks, G.A., and Packer, L., (1982) Free Radicals and Tissue Damage by Exercise, Biochem. Biophys. Res. Commun. 107, 1198. Deuel, H.J., (1948) The Digestibility of Rapeseed Oil in the Rat, J. Nutr. 35, 295. DFG, (1983) Deutsche Forschungsgemeinschaft, Zur Bedeutung d e r Fette in d e r menschlichen Entiihrung, WissenschaftlicheArbeitspapiere, Verlag Chemie, Weinheim. Doll, R., and Peto, R., (1981) The Causes of Cancer; Quantitative Estimates of Avoidable Risks of Cancer in the United States Today, J. Natl. Cancer Inst. 66, 1191-1308. Dormandy, T.L., (1983) An Approach to Free Radicals, Lancet 2, 101&1014. DPA, Kraftstoff aus der Nub, from Siiddeutsche Zeitung 4.5.1987. Driss, F., and Darcet, P., (1988) Effet des Huiles de Poison Riches en Acides Gras n-3 sur les Facteurs de Risque des Maladies Cardio-Vasculaires, Revue Frangaise des Corps Gras 35, 7-1 1. Dyerberg, J., Bang, H., and Home, N., (1975) Fatty Acid Composition of the Plasma Lipid in Greenland Eskimos, Am. J. Clin. Nutr. 28, 958-966. Erman, A., and Ranke, H., (1923) Agypten und das agyptische Leben im Altertum, Verlag J.H.C. Mohr, Tubingen. von Euler, US., (1934) Zur Erkenntnis der pharmakologischen Wirkungen von Nativsekreten und Extrakten miinnlicher accessorischer Geschlechtsdriisen, Naunyn-Schmiedeberg 's Arch. Exp. Path. P h a d 78, 175. von Euler, U.S., (1935) iiber die spezifisch blutdrucksenkende Substanz des menschlichen Prostata und Samenblasensekrets,Klin. Wschr. 14, 1182. FAO/WHO (1977) Dietary Fats and Oils in Human Nutrition. F A 0 Food and Nutrition Paper no. 3, Food and Agriculture Organization of the United Nations, Rome. Fink, D.J., and Kritchevsky, D., (1981) Workshop on Fat and Cancer, Cancer Res. 41,3677. Foote, C.S., (1982) Absorption of Singlet Oxygen by p-Carotene, in Pathology of Oxygen, (Autor, A., ed.), pp. 2 1 4 , Academic Press, New York. Friedeberg, A S . , Milking Taxpayers or Making Milk Quotas More Market Oriented, Speech delivered at the 29th Annual General Meeting of the International Federation of Margarine Associations, Oslo, 2. Juni 1986 (Unilever Publication). Friedeberg, AS., Protectionist Rebalancing or Market-Orientated Reform, The EC's Oils and Fats Policy in Focus, Speech delivered at the 10th Anniversary Conference of PORIM, Kuala Lumpur, 1989 (Unilever Publication). Friis-Hansen, B., (1965) in Humun Body Composition, (Brozek, J., ed.),p. 191, Pergamon, Oxford.
Importance of Fats
49
Gander, K.F., (1984) Die Fettversorgung des Menschen aus wirtschaftlicher und technologischer Sicht, Fette Seifen Anstrichrn, 86, 1. Geiger, P.L, (1830) Handbuch der P h a m z i e , Heidelberg. Geigy, J.R. AG, Pharma Basel, Documenta Geigy, Wissenschaftliche Tabellen, 7.Auflage. Goldberg ,C., and Schonfeld G., (1985) Effects of Diet on Lipoprotein Metabolism, Annu. Rev. Nutr. 5, 195-212. Gottenbos, J.J., (1985) in The Role of Fats in Human Nutrition, (Herausgeber Padley, F.B., and Padmore, J. eds.), pp. 117-131, Ellis Howard,Chichester. Gottenbos, J.J., (1988) in Dietary Fat Requirements in Health and Development, (BeareRogers, J., ed.), pp. 107-1 19, American Oil Chemists' Society, Champaign, IL. Groen, J., Tjong, B.K., Kamminga, C.E., and Willebrands, A.F. (1952) The Influence of Nutrition, Individuality and Some Other Factors, Including Various Forms of Stress, on the Serum Cholesterol. Voeding 13, 556. Gmndy, S.M., (1986) Cholesterol and Coronara Heart Disease, A New Era, State of the M e v i e w , J. Am. Med. Assoc. 256,2849-2858. Hagemeister, H., Precht, D., Franzen, M., and Barth, C.A. (1989) Transfer von omega-3Fettsauren in das Milchfett von Kiihen, Proceedings of the Annual Meeting of DGF, Miinster, 1989, p. 22. Hamm, D.J., (1984) Preparation and Evaluation of Trialkoxytncarbakylate, Trialkoxycitrate, Trialkoxyglycerylether, Jojoba Oil and Sucrose Polyester as Low Calorie Replacements of Edible Fats and Oils. J. Food Sci. 49, 419. Hammond, E.G., (1988) Trends in Fats and Oils Consumption and the Potential Effect of New Technology, Food Technol. (Jan.), 117. Hansen, A.E., Haggard, M.E., Boelsche, A.N., Adam, D.J.D., and Wiese, H.F., (1958) Essential Fatty Acids in Infant Nutrition 111. Chemical Manifestations of Linoleic Acid Deficiency, J. Nutr. 66, 565. Hanssen, E., and Wendt, W., (1965) Die Geschichte der Lebensmittelwissenschaft, in Handbuch der Lebensmittelchemie, vol. 1, Springer Verlag, Berlin. Harris, S.W., (1989) Fish Oils and Plasmalipids and Lipoprotein Metabolism in Humans: A Critical Review, J. Lipid Res. 30, 785-807. Holman, R.T., (1961) How Essential Are Fatty Acids? J. Am. Med. Assoc. 178, 930-933. Holman, R.T., (1963) Symposium on Human Calcium Requirements, J. Am. Med. Assoc. 185, 588-593. Holman, R.T., Caster, W.O., and Wiese, H.F., (1964) The Essential Fatty Acid Requirement of Infants and the Assessment of Their Dietary Intake of Linoleate by Serum Fatty Acid Analysis, Am. J. Clin. Nutr. 14, 70-75. Hunter, J.E., (1989) Scientists Discuss Dietary Fatty Acids. J. Am. Chem. SOC. 66, 1251-1256. Kankare, V., and Antila, V., (1989) Extraktion von Milchfett mit iiberkritischem Kohlendioxid, Fat Sci. Technol. 91, 485. Kinlen, L.J., (1983) Fat and Cancer, Br. Med. J. 286, 1081-1082. Kinsella, L.W., Partridge, J., Boling, L., Margen, S . , and Michaels, G., (1952) Dietary Modification of Serum Cholesterol and Phospholipid Lev&, J. Clin. Endocrinol. 12, 909. Krinsky, N.I., and Deneke, S.M. (1982) Interaction of Okygen and Oxy-Radicals with Carotenoids, J. Natl. Cancer Inst. 65, 205-210. Kromhout, D., Bosschieter, F., and Goulander, C., (1985) The Inverse Relation Between Fish-Consumption and 20-Year Mortality from Coronary Heart Disease, N. Engl. J. Med. 312, 1205-1209.
50
fats and Oils Handbook
Laasko, I., Seppben-Laasko, T., Vanhanen, M.D.H., (1989) Effects of Partial Rapeseed Oil Substitution on Serum Cholesterol, DGF Annual Meetin, Miinster, 1989, p. 6. LaBarge, R.G., (1988) The Search for a Low Caloric Oil, Food Technol. 84. Lambert, J.P., (1993) Meat, Dietary Importance, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 2949, Academic Press, London. Langdon, R.G., and Philips A.H., (1961) Lipid Metabolism, Annu. Rev. Biochem. 30, 189-2 12. Leaf, A., and Weber, P.C.,(1988) Cardiovascular Effects of n-3 Fatty Acids, N. Engl. J . Med. 318, 549. Leonhard E.C., The Economics of the Commercial Tropical Oils, Speech delivered at the 21st World Congress of the International Society for Fat Research, The Hague, October 1995. LRC-CPT, Lipid Research Clinic Coronary Primary Prevention Study, JAMA, Deutsche Ausgabe, 231-255, April 1984. Ludwig, L., (1968) Fett und Erniihrung, p. 49, Internationale Margarine Information, Wien. Macy, I.G., (1949) Composition of Human Colostrum and Milk, Am. J. Dis. Child 78, 5 89-503. Mathews-Roth, M.M., (1982) Photosensitizitian by Porphyrins and Prevention of Photosensitization by Carotenoids, J. Natl. Cancer Inst. 69, 279-285. Mattson, F.H.,,Jandacek, R.B., and Webb, M.R., (1976) The Effect of Nonabsorbable Lipid, SucrosePolyester, on Absorption of Dietary Cholesterol by the Rat, J. Nutr. 106, 747. McGandy, R.B., and Hegsted, D.M., (1975) Quantitative Effects of Dietary Fat and Cholesterol on Serum Cholesterol in Man, in The Role of Fats in Human Nutrition, (Vergroesen, A.J., ed.), Academic Press, London. McIntyre, R.T., (1979) Polyglycerol Ethers, J. Am. Oil Chem. SOC.56, 835A. Melchert, H.U., (1988) Fettsaurespektren ausgewahlter Lipidklassen des Serums bei Vegetariern und Nicht-Vegetariern, Lebensmittelchem gerichtl. Chem. 42, 119. Mertz, D.P., (1983) Butter oder Margarine? Zur Klarung einer Streitfrage, Deutsche Apotheker Zeitung, 123, 465. Mielke, R., (1985) Present and Future Position of Palm and Palm Kernel Oil in World Supply and Trade, J. Am. Oil Chem. SOC.62, 193-197, Mielke T., (1990) Current World Supply, Demand and Price Outlook for Oils and Fats, in World Conference Proceedings, Edible Fats and Oils Processing: Basic Principles and Modern Practices, (Erickson, D.R., ed.), pp. 1-9, American Oil Chemists’ Society, Champaign, IL. INFORM I , 190, (1990), Morehouse, S.E., (1990), citation from Am. J . Clin. Nutr. 46 (1987), and J. Food Sci. 54 (1989). National Institutes of Health Consumers Development Conference Statement 5, no. 7 (1984), in J. Am. Med. SOC.253, 2080-2086, (1985). National Research Council (1982) Diet, Nutrition and Cancer, National Academy Press, Washington DC. Nitske, W.R., and Wilson, C.M., (1965) Rudolf Diesel, Pioneer of the Age of Power, University of Oklahoma Press, Normann, OK. Numa, S., (ed.), (1984) Fatty Acid Metabolism and Its Regulation, Elsvier Science Publishers, New York. Peters, J.P., and van Slyke, D.D., (1946) Quantitative Clinical Chemistry, Williams & Wilkins, Baltimore.
importance of Fats
51
Pimparkar, B.D., (1961) Correlation of Radioactive and Chemical Fecal Fat Determinations in the Malabsorption Syndrome, Am. J. Med. 30, 910-926. Pryde, E.H., and Rotfuhs, J.A., (1989) Industrial and Nonfood Use of Vegetable Oils, in Oil Crops of the World, (Robbelen, G., Downey, R.K., and Ashri A., eds.), McGraw Hill, New York. Pryor, W.A. (ed.),(1976) Free Radicals in Biology, Academic Press, New York. Quick, G.R., (1989) Oil Seeds as Energy Crops in Oil Crops of the World, (Robbelen, G., Downey, R.K., and Ashri, A., eds.), McGraw Hill, New York. R e m a , G., Dattagupta, C., Listowsky, P., Levenson, S.M., and Siefter, E., (1983) Fed. Proc. Fed. Am. SOC. Exp. Biol. 42, 786. Cited from Ames, B.N., Science 221, citation 116, p. 1256. Richtler, H.J., and Knaut, J., (1991) Umwelt und Fettchemie-Eine Herausforderung, Fen, Wissenschaji Technologie 93, 1-12. Rizzi, G.P., and Taylor, H.M., Synthesis of Higher Polyol Fatty Acid Polyesters, U.S. Patent 3.963.699, (1976). Robbelen, G., and Hirsinger F., (1982) in Improvement of Oil-Seed and Industrial Crops by Induced Mutations, pp. 161-170, Int. Atomic Energy Agency, Wien. Robbelen, G., and Hirsinger F., (1983) Fortschritte in der Welterzeugung von Rapssaaten, Fette, Seifen, Anstrichmittel 85, 395-398. Robbelen, G., and Hirsinger F., (1987) Development of New Industrial Oil Crops, Fat Sci. Technol. 89, 563-570. Robbelen, G., Hirsinger F., and von Witzke, S., (1987) Possible Use of Mutation Breeding for Rapid Domestication of New Crop Plants, Int. Atomic Energy Agency, Wien. Schettler, G., (1984) Der Mensch ist so jung wie seine Gefasse, Piper-Verlag Miinchen. Schlierf, G., (1986) Gegenwiirtiger Stand der Ernahrungstherapie bei degenerativen Herzund Gefabkrankheiten, Therapiewoche 36, 1349-1352, Schiittauf, W., and Pischel, U., (1978) Die Margarine in Deutschland in der Welt, Presseabteilung der Union Deutsche Lebensmittelwerke, Hamburg. Schiittauf, A.W.,( 1942) Probleme der Wel@ettversorgung, Internationale Agrarmndschau, Heft 3, Berlin Schwandt, P., (1987) Therapeutische Effekte diatetischer Mabnahmen bei Patienten mit Hyperproteinamien, Akt. Emahr. 12, 7-10. Sebrell, W.H. Jr., and Harris, R.S.., (1954) The Vitamins: Chemistry, Physiology, Pathology, vol. I, p. 1, vol. 11, p. 131, vol. 111, p. 481, Academic Press, New York. Seher, A,, (1987) Der Cholesterin-Gehalt von Pflanzenolen, Fat Sci. Technol. 89, 27-30. Seidel, H., (1983) Fettchemie hat Zukunft ... (Interview mit Geschaftsleitungsmitgliedern der Schering AG), Chem. Ind. 251. Shell, private information from The Hague Headquarters, the Netherlands (1990). Singer, P., Die Rolle der Eicosapentaensaure im Rahmen polyenreicher Diaten, Sonderdruck der Emihungs-Umschau. Stadelman, W.J., (1993) Eggs, Dietary Importance, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 1534, Academic Press, London. Stamler, J., and Epstein, F.H., (1966) Coronary Heart Disease-Risk Factors as Guide to Preventive Action, Prevent. Med. 27, 1. Stover, H.-M., Munch, E.-W., and Sitzmann, W., (1988) Gewinnung von Mineralolsubstituten aus Olsaaten, Fen, Wissenschaf, Technologie 90, 547-550. Strycker, W.A., (1941) Absorption of Liquid Petrulatum from the Intestine: A Histologic and Chemical Study, Arch. Pathol. 31, 670.
52
Fats and Oils Handbook
TaufeVTerneflunger/Zobel, Cholesterin in Lebensmittellexikon, Behr's Verlag, 1993. Thiele, O.W., (1982) Bedarf des Menschen an essentiellen Fettsiiuren, ZFA Zeitschrifi fiir Allgemeinmedizin 58, 1329-1331. Thomasson, H.J., (1953) Biological Standardization of Essential Fatty Acids, Int. Z . Vitaminforsch. 62, 25. Toma, R.B., Curtis, D.J., and Sobotor, C., (1988) Sucrose Polyester: Its Metabolic Role and Possible Future Applications, Food Technol. 93. Tucker, B.W., and Pigott, G.M., (1993) Fish Oils, Composition and Properties, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 1896, Academic Press, London. Umweltbundesamt, Okologische Bilanz von Raps61 bzw Rapsolmethylester als Ersatz von Dieselkraftstoff (Okobilanz Rapsol), Berlin, January 1993. UNION, 50 Juhre UNION, Werkszeitschrift der UNION Deutsche Lebensmittelwerke, Hamburg, (1979). Vles, Gottenbos, J.J, Nutritional Characteristics and Food Uses of Vegetable Oils, in Oil Crops of the World, (Robbelen, G., Downey, R.K., and Ashri, A., eds.), McGraw Hill, New York. Vogt, L., (1987) Entwicklung und Anwendung eines Fettersatzstoffes, Lebensmitteltechnik, 642. Volpenheim, R.A., Synthesis of Higher Polyol Fatty Acid Polyesters Using High Soap: Polyol Ratios, U.S. Patent 4.518.772 (1985). Wagner, J., (1988) Is There Finally a Perfect Fat Replacer? Food Engineering International 9. Wang, Y.M., (1982) in Molecular Interrelations of Nutrition and Cancer, (Wang, Y.M., Amott, M.S., van Eys, J., eds.), pp. 369-379, Raven Verlag, New York. Welch, V.A., (1993) Fats, Digestion, Absorption and Transport, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 1731, Academic Press, London. Wirths, W., (1981) Kleine Ndhwerftabelle,Umschau-Verlag, Frankfurt. Wolfram, G., (1987) Metabolische Wirkungen linolsaurereicher Kost, Aktuelle Emdhrungsmedizin 12, 11-19. Wooley, C.C., (1929) Vor 5000 Juhren, Verlag H. Franckh, Stuttgart. Xue, S.P.,(1980) Proceedings of Symposion on Recent Advances on Fem'liry Regulation, p. 122,2-5 Sept., Peking. Yagi, K., Okhawa, H., Ohishi, N., Yamashita, M., and Nakashima, T., (1981) Lesion of Aortic Intima Caused by Intravenous Administration of Linoleic Acid Hydroperoxide, J. Appl. Biochem. 3, 58. Yamori, Y., Nara, Y., Iritani, N., Workman, R., and Inagami, T., (1985) Comparison of Serum Phospholipid Fatty Acids Among Fishing and Farming Japanese Populations and American Islanders, J. Nutr. Sci. Vitaminol. 31, 417-422. Zabik, M.E., citation in J. Am. Oil Chem. Soc. INFORM. I 9 0 (1990), citation from Am. J. Clin. Nutr. 46 (1987) und J. Food Sci. 54 (1989).
Chapter 2
Composition, Structure, Physical Data, and Chemical Reactions of Fats and Oils, Their Derivatives, and Their Associates To understand the reactions of fats and oils and the technologies applied, as well as to be able to influence their characteristics and behavior during processing, it is important to know their properties and reactions. The number of main building blocks that make up common oils and fats is relatively small. Most of the different characteristics occur as a result of minor components and the immense number of possible combinations of these building blocks. Under natural conditions, the number of major reactions of oils and fats that lead to alteration is small.
*: H H
-
-
for instance R = - C (CH& CH3
I;
OR,
Scheme 2.1.
Fats are esters of fatty acids with the trihydric alcohol glycerol. Because of the symmetrical structure of the glycerol molecule, two identical outer positions (1-, 3-) and one central position (2-) exist, to which the fatty acids are esterified. The type of fatty acid, as well as the distribution across these positions, determines the characteristics of the triglyceride. Not only the composition by summation equation but also the structure of the triglyceride is therefore of great importance. The share of different fatty acids in the world production of common edible fats and oils is of interest (Table 2.1). The calculation of Boekenoogen (1941) is now more than fifty years old. Today’s distribution is different, mainly as a result of a shift of the main production areas from the tropical regions of the world to those with moderate climates and also because of new crop cultivation. The table shows the distribution of 1941, and 1950 onwards, each calculated for average fatty acid composition per species. The fatty acid composition of the main seed and pulp oils does not differ substantially among the main types. Therefore, shifts of only a few percentage points in the table may be caused by immense shifts in cultivation. So little a share of erucic acid remains, for example, that it disappears by rounding off. In new rape varieties, it is almost completely substituted by oleic acid. Furthermore, the trend toward oilseeds with a high content of essential linoleic acid is clear; coconut oil has drastically
decreased relative to the other oils, resulting in a parallel decrease in the appearance of lauric acid. The fatty acid compositions of the individual oils and fats are described 53
Fats and Oils Handbook
54
TABLE 2.1 Fatty Acid Distribution of the Common Vegetable Fats and 0ilsa.b Share (%) ~
Fatty acid C,,:, C,,:, C,,:,
C12:, C,:, C14:o C,: C,:,
Oleic Linoleic Palmitic Lauric Linolenic Myristic Erucic Stearic All others
~~
1941
1950
1960
1970
1980
1990
34 29 11 7 6 3 3 3 4
30 24 14 8 6 3 8 3 4
29 32 14 7 5 2 5 3 3
30 36 13 4 6 2 2 3 4
31 38 14 4 5 2 0 4 2
31 37 16 3 5 1 0 4 3
agecause fatty acid composition of vegetable oil is not uniform within the same kind of oil, these rounded figures are only indicative; however, they are based on thoroughly calculated figures from averages. bource: Boekenoogen (1 941) and own calculations.
in Chapter 4. Here, only the principles of composition and structure will be discussed. One unsaturated fatty acid is ubiquitous in fats and oils; two are almost ubiquitous. Oleic acid is present in all known fats and oils and also predominates in quantity (Table 2.1). Almost all fats and oils contain its next lower homologues, palmitoleic acid (although in very small quantities) and the double unsaturated acid with the same chain length as oleic acid, namely, linoleic acid, as well as other CIgZ2 acids. None of the saturated fatty acids is omnipresent. However, palmitic acid has almost the same distribution as oleic acid. The distribution of myristic acid and stearic acid is similar to that of linoleic and palmitoleic acid. To date, the fat and oil of -5000 species (animals and plants) have been analyzed. No correlation between their composition and occurrence has yet been found. As early as 1935, Hilditch proposed a link between the fatty acid composition of fats and the evolutionary stage of the species in which they occur-beginning with microorganisms and marine monocellular organisms via marine plants and animals, to both terrestrial animals and plants. No real evidence could be found for this approach, although some indications for this connection may exist (Fig. 2.1). It seems evident that the amount of saturated fatty acids and unsaturated C,8fatty acids (mainly oleic acid) increased during the course of evolution. Unsaturated long-chain fatty acids tended to disappear and palmitoleic acid (due to its occurrence also named zoomaric acid) diminished dramatically. Similar trends are also expected in vegetable fats, but an insufficient number of lower plants have yet been analyzed to prove this. However, some hints can be found in the change of fatty acid composition that occurs during the ripening of seeds following patterns similar to evolution (see also Chapter 4). In total, the spectrum of fatty acids that occur in main edible oils and fats is represented by no more than 10-12 compounds, representing >98 % of all fatty acids in food. Statistically, however, 10 different fatty acids allow the formation of
Composition, Structure, Physical Data, and Chemistry
55
Fig. 2.1. Proportion of certain fatty acids on the fat of sea and land animals (after Hilditch and Williams 1964).
more than 650 different triglycerides. Nature does not follow statistical distribution; therefore not all possible combinations can be found. The model of restricted statistical distribution best simulates reality (see Chapter 2.2). Only a part of the different physical and chemical characteristics of fats and oils is caused by the special characteristics of the fatty acids themselves, or by those fatty acids that represent the residual 2%. One of the main parameters influencing the characteristics of fats and oils is the degree of unsaturation of their fatty acids; this can be changed by hardening (see Chapter 6.5). The other concerns the distribution of the 10-12 main fatty acids over the three different positions of the glycerol molecule. Therefore, great efforts are undertaken to separate certain triglycerides (see Chapter 6.2) or to change their distribution in the glycerol molecule (see Chapter 6.4). Fats have a density d,, of 0.91-0.95 cmVg, a very low vapor pressure and consequently, a very high boiling point. The melting point of oils usually lies below O"C, the melting point of the highest melting fraction of fats at about 75°C. Solubility is very good in nonpolar solvents and chlorinated hydrocarbons. The main chemical reactions that occur naturally are saponification and oxidation. Fats usually are accompanied by lipids such as carotene, sterols and phosphatides. Many oilseeds contain other specific components, which usually have to be removed during processing.
2.1 Components of Fats and Oils 2.1.1 Glycerol Glycerol (propane-l,2,3-triol) is the one and only alcohol to which fatty acids are esterified into triglycerides, i.e., oils and fats. Living organisms synthesize glycerol
Fats and Oils Handbook
56
from hexose; in the body, this reaction is much faster than the synthesis of fatty acids. That is why glycerol is always available in sufficient quantities (Propjak 1953) for the synthesis of fats. The Swedish pharmacist and chemist, Scheele, discovered glycerol in 1783 when he experimented with olive oil. Chevreuil, the father of fat chemistry, gave the sweettasting substance its name, which is derived from the Greek word for sweet.
H
rrzi I
I
I
H or
n n n
H
Scheme 2.2.
Glycerol is a symmetrical triple alcohol (for physical data, see Table 2.2) and is important as the basic component of all triglycerides. However, as the one and only identical alcohol component that is present in all triglycerides, it becomes unimportant for the technology of fats and oils. The only importance is in its reesterification with fatty acids to yield very special dietetic fats (see Chapter 8.7). The situation is totally different in the technical fats market. At present, the world consumption of glycerol is -500,000 MT/y. Most of it is for the chemical and pharmaceutical industry; a smaller part is used for food, tobacco and plastics manufacturing. Since 1948, glycerol has not been exclusively produced from oils and fats; it is also synthesized, for example, from propylene (Sherwood 1960). In difficult times, e.g., during the war in Germany, it can also be produced via fermentation of saccharose or hydrogenation of saccharose and starch with nickel catTABLE 2.2 Physical Data of Glycerol (Propanetrio1)a ~~
Molecular weight Melting point Boiling point Density Refractive index Viscosity relative kinematic Solubility in water in alcohol in benzene Dissociation constant
M= m.p. = b.p. 760 = b.p.1, = D420= n ,,20 =
~
~
92.1 1 2ooC ( 6 8 O F ) 29ooC (554OF) 8 2 . K (360°F) 1.261 1 g/cm 1.4746 1759.6 (cP) 1398.1 (cP) infinitely infinitely infinitely 7.10-15
pK = aSource: Handbodc dCkmistry and Physics (1 976).
14.15
Composition, Structure, Physical Data, and Chemistry
57
alysts. The present use of glycerol in Europe is shown by Steinberner and Preuss (1987), who also further explain glycerol production. 2.1.2 Fatty Acids
Today, >200 fatty acids are known to occur in fats and oils. Only a handful have a share >3% in the triglycerides of edible oils and fats. A further handful fall in the region of 0.5-3.0%. All others exist only as traces in common oils and fats; they can be found in higher amounts in special species. The most important saturated fatty acids were discovered in the first half of the 19th century. The initial discoveries occurred around 1820 with the basic work of Chevreuil who found butyric, capronic, and capric acid as well as palmitic and stearic acid. The others were discovered by Lerch and Fehling (caprylic acid 1844-45) and Marsson (lauric acid 1842 in the fat of laurel, Luuris nobilis). Arachidonic acid was found by Gossmann (1854) in peanut oil, behenic acid by Voelcker (1848) in behenic oil. Hell and Hermans identified lignoceric acid (1880) in beech tree tar. Five years earlier, oleic acid had been identified as the most important component of fats and oils. A survey of the history of discovery and identification of the fatty acids is given by Hilditch and Williams (1964). Ucciani (1995) gives the fatty acid composition of more than 2000 plants. Naturally occurring fatty acids are usually monobasic and unbranched. They are aliphatic monocarbonic acids, mainly saturated or mono- or bi-unsaturated. Higher degrees of unsaturation occur in marine oils. In animal and vegetable triglycerides, even-numbered chain lengths between 4 and 26 carbon atoms dominate; in waxes, chain lengths up to 38 exist. In fats of microorganisms, odd-numbered chain lengths can constitute up to 15% of all fatty acids. In the beginning of fat chemistry, high amounts of C,, fatty acid (margaric acid) had been found. This later proved to be a mixture of C16 and C18 that could not be separated with the analytical methods of that time. In the following sections, fatty acids are described with emphasis on the main members of each family. Selected others are shown in a table. Detailed information on fatty acids, their sources and their properties is given by Hilditch and Williams (1964), Geigy (1968), Baltes (1975), Swern (1982), and Gunstone et al. (1986). Original citation of literature from which physical data are taken can also be found. The main fatty acids also have trivial names that allow for clear classification in the case of saturated fatty acids. For unsaturated fatty acids, cis- or truns-configuration can be deduced mainly from the trivial name. In polyunsaturated fatty acids, the trivial name gives chain length and the number of double bonds; their position and configuration is marked separately. 2.1.2.1 Structure and Nomenclature. Fatty acids are monocarbonic acids that are usually derived from aliphatic hydrocarbons and can be brought into a systematic pattern (Fig. 2.2). All dominant fatty acids of edible oils and fats belong to the
Fats and Oils Handbook
58
families of alkane- and alkene-fatty acids. Their structure and nomenclature follow the common rules of chemistry. However, the main fatty acids also carry trivial names, which are commonly used. The carbon chain is, as usual, numbered from the carbonyl-end to mark functional groups. In addition there is a consensus in fat chemistry to number double bonds beginning from the methyl-group at the tail. Following that, a prefix “n” or ‘‘a” is used with the number of the carbon atom. Four different C1, fany acids are shown in Figure 2.3 with their trivial names, chemical names, structure and sum equation. The structure of fatty acids has a great influence on their physical data. With the main fatty acids from edible oils and fats, structural differences can occur only in the position of the double bond or its configuration (cis- or trans-). The influence of these parameters on the physical properties is shown in Figure 2.4 for the C,, acids, with one double bond in different positions and for both geometric isomers. Tables 2.3 through 2 7 give the physical data and typical sources. 2.7.2.2 Saturated Unbranched Fatty Acids. The lowest homologue, acetic acid (C,) cannot be found in triglycerides. The lowest in the sequence of “real” fatty acids is butyric acid C,, first found in butter as its name indicates.The acids up to C, are liquid and are found mainly in milk fat. Capric, myristic, and lauric acid are typical for coconut oil and palm kernel oil (“lauric fats”), and palmitic and stearic acids are the most common saturated fatty acids. Table 2.3 gives physical data. 2.1.2.3 Unsaturated Unbranched Fatty Acids. These fatty acids are very special because some of them are essential for mammals, i.e., also for man. This means that the body cannot synthesize them and is dependent on an external supply (see Chapter 1.4).
Unk.noh.d 2.1.2.2 2.1.2.4
-
B R W
SubrtyII(.d
2.1.2.4
2.1.2.4
2.1.2.3.1
2.1.2.3.2
Fig. 2.2. Systematic of fatty acids.
m 2.1.2.4
Composition, Structure, Physical Data, and Chemistry
59
/OOH unbranched, di-unwtualCtnnr-9,12octsdhic add (linolelsdbnic add)CitHnOc or H~C-(CH~)~CH~CH-CHZ-CH~CH-(CHZ)~-COOH
Fig. 2.3. C,, fatty acids of different degree of saturation.
70 60
c . .
2G.././..
50
E
tranr-
E40
2
configuration
30
P 20
cisI
10
0 '
2
3 4 5 I 6 7 8 9 1 0 1 1 1 2 Position of the double bond in the C18:l fatty acid
Fig. 2.4. Melting points of CI8:, fatty acid isomers (after Kaufmann 1958 and Markley 1947).
01
0
TABLE 2.3 Physical and Chemical Data of Common Saturated Fatty Acids CnH2n02 n
Trivial name
Chemical name
Molecular weight
4 6 8 10 12 14 16 18 20 22 24 26
Butyric Caproic Caprylic Capric Lauric Myristic Palmitic Stearic Arachidic Behenic Lignoceric Cerotic, Phthioic
n-Butanoic mHexanoic n-Octanoic n-Decanoic n-Dodecanoic n-Tetradecanoic n-Hexadecanoic n-Octadecanoic n-Eicosanoic n-Docosanoic n-Tetracosanoic n-Hexacosanoic
88.1 1 116.16 144.22 172.27 200.32 228.38 256.43 284.49 312.54 340.59 368.65 396.71
Melting point (T) -7.9 -4 16.7 31.3 43.5 54.4 62.9 69.6 75.4 79.9 84.2 87.9
Boiling pointlpressure (“Umm Hg)
Density Refractive index (g/mL at T) n,Yt (unitsPC)
163.51760 205.81760 239.7l760 269/760 2251100 250.5/100 268.511 00 2981100 3281100 306160
0.9387120 0.9290120 0.9088/20 0.8858140 0.8830120 0.8584160 0.8487l70 0.9408120 0.82401100 0.82211100 0.82071100 0.81981100
-
64110 99110 124110 152110 130.511 149.21 167.51 183.611 205.011 257110 272110
-
-
1.39906/20 1.41 635120 1.4285140 1.42855120 1.41 83/82 1.4308/60 1.4276180 1.4297180 1.4250/100 1.42701100 1.42871100 1.43011100
Acid number 637 483 389 325 280 245 218 197 179 164 152 141
2 G: rLJ
a-
0 i z $
[ 3
Composition, Structure, Physical Data, and Chemistry
61
2.1.2.3.7 Monounsaturated fatty acids. The shortest chain unsaturated fatty acid that has been found to date in natural fats is caproleic acid (Clo:l),traces of which have been identified in milk fat. The only monounsaturated fatty acid that occurs in substantial amounts is cis-9-octadecenoic acid, which has the trivial name of oleic acid (for sources and derivatives, see Hilditch and Williams 1964). All other acids occur on average at much lower percentages. This does not mean, however, that their contribution to the fatty acid spectrum of specific sources must be low. Cruciferae, for instance, contain high amounts of cis-13docosenoic acid, i.e., erucic acid (older varieties of rape contained up to 70%). Generally monoenoic acids are found as follows: Cl0:, to C18:1,in milk fats; CI6:, in seed oils. to CZ4:*, in marine oils; and up to Only in special plants have other isomers been found, e.g., cis-6-octadecenoic acid makes up between 4 and 97% (e.g., dill, caraway, persil) of total octadecenoic acid isomers in apiaceae varieties, cis-11-octadecenoic acid up to -20% (mallow) in malvaceae (Seher 1982). Table 2.4 presents the data for monounsaturated acids.
2.1.2.3.2 Polyunsaturated fatty acids. In addition to the cis- or trans-isomers of monoenic acids, polyenic acids offer further potential for isomerization, such as cis- and trans- in one molecule, and for isolated or conjugated double bonds. Polyunsaturated fatty acids (see Table 2.5) with isolated double bonds appear in all edible fats and oils. In native vegetable triglycerides, only all-cis isomers are found, but they are also present in animal fats. However, because the body cannot synthesize them, they are obtained from vegetable food. Highly unsaturated fatty acids occur in organ fats and marine oils. Conjugated polyunsaturated fatty acids are found almost exclusively in nonedible oils and fats. Alkyne fatty 'acids are extremely rare. The most important polyunsaturated fatty acids are linoleic and linolenic, both in amount and in their essential role in the human (animal) diet; arachidonic acid also has this essential role, although it occurs in much smaller amounts. Clupadonic acid is included in the table for its occurrence in fish oils (Table 2.5). 2.7.2.4 Other Fatty Acids. In addition to the unsaturated fatty acids mentioned above, there are alkyne fatty acids, branched fatty acids, alicyclic fatty acids and substituted fatty acids. These subgroups have no importance at all for edible fats. Some are included in the table as examples. Alkyne fatty acids are especially rare. For example isanic fatty acid (17octodecene-9,ll-diyonic acid) is mentioned, found in boleko oil (Baltes 1975) and tariric acid (6-octadecynoic acid), which occurs in piramnia species. Branched fatty acids are found at trace levels in many fats, predominantly animal fats. Substituted fatty acids are rare but equally important. Hydroxy fatty acids account for 53% of the cerebrosides (Chibnall et al. 1953, Mislow and Bleicher 1954) and are very important for brain function.
TABLE 2.4 Physical and Chemical Data of Common Monounsaturated Fatty Acids C"HZ",O2
n
Trivial name
12 Linderic (Laudeic) 14 Myristoleic 16 Zoomaric 18 18 18 18
Oleic Elaidic Petroselink Vaccenic 20 Cadoleic 20 Gondoic 22 Erucic
Molecular weight
Melting point
CH,
5-Dodecenoic
n-9
9
198.31
1.C1.3
17C173113
9-letradecenoic 9-Hexadecenoic (Palmitoleic) 9c-oaadecenoic 9fOaadecenoic 6c-Octadecenoic Ilt-Octadecenoic 9-Eicosenoic 11-Eicosenoic 13-Docosenoic
n-5 n-7
5 7
226.36 254.42
4.5 0.5
183-1 86/14 2 1a22011 5
From
o
("0
(g/mL at "c)
Refractive index n & t (unitsPC)
-
0.913W15
1.4535115
128
283
144m.6 1 8 ~8311 1
0.9130115 0.9003115
1.4549115
112
248
1.4587/20
100
221
1.4582/20 1.4499145 1.4535/47 1.4439160 1.446W50 1.4597/20 1.4W64
90
199 199 199 199 181 181 166
Boiling point pressure/ ("Umm Hg)
Chemical name
Density
Iodine Acid value number
2' i: (L,
i% z
(L,
3
n-9 9 n-9 9 11-12 12 7 n-7 n-11 11 n-9 9 n-9 9
282.47 282.47 282.47 282.47 310.52 310.52 338.58
13 51 32-33 44 24.5 25 33.5
203-20515 28fY100 234115 lW1851O.5 20~210110. 14ai52m.15 172-1 73/3 17W0.1 32W60(d) 203-20511 281130 252-254112
0.895/15 0.85/20 0.8824135
0.8882f25 0.82W100 0.8W55
90
90 90 82 82 75
g
TABLE 2.5 Physical and Chemical Data of Common Monounsaturated Fatty Acids C"H2"-2O2 n
Trivialname x
12 Linoleic 18 a-Linolenic 18 ylinolenic 18 Elaeostearic 20 Arachidonic 20 Timnodonic 22 Clupadonic 22 Cervonic
Miscellaneous n Trivial name 18 Ricinoleic 24 Nisinic 24 Nervonic 24 Cerebronic 24 2-Hydroxynervonic
Chemicalname
4
9,12-Octadecadienoic (LA) 6 9,12,1-decatrienoic (ALA) 6 6,9,12-oaadecatrienoic (CIA) 6 9~,llt.l3t-Octadecatrienoic 5,8,11,1 &Eisosa8 tetraenoic (AA) 10 5,8,11,1417-Eisc+ sapentenoic (EPA) 10 4,8,12,15,19Docosapentenoic (DPA) 12 4,7,10,13,16,19-W cosahexaenoic (DHA)
Chemical name cisl2-Hydroxy9-octadecenoic 4,8,12,15,18,21Tetracosahexaenoic 15-Tetracosenoic 2-Hydroxytetracosanoic 2-Hydroxy15-tetracosenoic
From CH, o
Molecular weight
Melting point
0
n-6
6
280.44
-5.2
n-3
3
278.42
-11
n-6
6
278.42
n-5
5
n-6
Refractive Density index nDM (g/ml at "C) (uniWC)
Iodine value
Acid number
0.9020/20
1.4699/20
181
200
0.9046RO
1.478ORO
2 74
202
-
2 74
202
0.9028/50
1.51 12150
274
202
0.92 19/20
1.4824/20
304
184
1.4977R3
-
186
0.9290RO
1.5014RO
464
170
-
1.5017/20
-
172
Density (g/mLat "C)
Refractive index nDVt (uniWC)
Iodine value
Acid number
0.9403/27
1.4716RO
85
188
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- _
Boiling point I pressure (Wmm Hg) 229-230 I16 23C232 I 17
129 10.02 125 10.05
4
-
-
278.42
49
6
304.46
49.5
235 I 12 217-220 I17
n-3
3
302.45
-
-
170 /1.3 169-171 m.15
n-3
3
330.50
<-78
-
n-3
3
328.49
<<-75
-
Melting point
Molecular weight
n-9
9
298.47
5.5
245 I1 0
n-3
3
356.55
-
n-9
9
366.64
112.5 113.5 40.541 99.5100.5 65
_ _ _ 384.65 n-9
9
382.63
-
-
207-2 12 /2
-
Boiling point I pressure(WmmHg)
From CH, o
K)
-
-
.
Fats and Oils Handbook
64
TABLE 2.6 Occurrence of Minor Fatty Acids in Different Oils ( O h ) In marine oil: herring oila c16:206 0.4 c18:3@6 O.3 0.1 0.4 C2,:403 0.4 in vegetable oil: rapeseed oilb c14:lo9 tr c14:lw7 0.007 c15:1,10 0.02 C1.j:lolo 0.01 c17:O 0.05 C17:1, 0.06
C16:me7
0.3
C162o4 C20:40b
In animal fat: lardb C13:o 0.08 C15:o C23:0br] 0.008 C24:obr] cl5:l 0.01 C17:1 C200br4 0.O2 C22:0br4
0.02 0.004 0.22 0.02
c16:204
Oh
c16:304
0.4
c16:401
c18:303
0.9 0.2
c200
o.l
c2D:lo9
C22:503
0.4
C24:1
C14:loS
0.004
c14:206
tr
c16:1~7
C190
0.02
Cjcj:,oio
0.02 0.29 0.02
c14:303
C15:l&
C1,:o
0.29 0.02 0.06 0.03
C1,:o
0.03 0.02 0.004 0.03
C22:206
C25:0brl Cig:, C24:0br4
C26:&rl C21:1 C260br4
0.4 o.2 Phytanic 0.2
o.6 0.3 0.4
c18:105
tr 0.07
c15:0
C16.06 C20.206
0.20
C2~306
C21:o
0.004 0.02 0.02 0.09
C23:o
c12:1 C22:3 C28:0br3
c202
C ,:,i
c]4:] C22:5 C28:0br4
0.02 0.13 0.20 0.02 0.03 0.02 o.20
aSource: Sigurgisladottir and Pilmadottir (1993). bSource: Sebedio (1 979). cSource: Iverson eta/. (1 965).
TABLE 2.7 Occurrence of Fatty Acidsa Saturated fatty acids CnH2nO2
n 4 6 8
Trivial name Butyric Caproic Caprylic
10 12
Capric Lauric
14
Myristic
16
Palmitic
18
Stear ic
20 22
Arachic Behenic
24
Lignoceric
26
Cerotic
Occurrence in common oils and fats Sources with remarkable moportion (% of total fattv acids) milk fat (3-5) milk fat (2-31, coconut oil (21 milk fat (a), babassu oil (3-51, coconut oil (4-61,palm kernel oil (13), cuphea painter; (65-75), hookeriana (-65) milk fat (3-4), babassu oil (4-7), coconut oil (6-9), cuphea species (88-92) coconut oil, palm kernel oil (45-SO), Litsea sebifera (-95), Cinnamonium inners (-95), cuphea tolucana (-65) coconut, palm kernel, babassu oil (15-1 7), herring oil ( 4 4 , nutmeg oil (177) Gymnacranthera contracta (-85), Scyphocephalum ochocoa (-80), cuphea palustris (-65) coconut oil, palm kernel oil, babassu oil, sesame oil (7-10), cottonseed oil (1 7-25), milk fat (33-38), lard (20-30), tallow (25-40), herring oil (7-1 3) menhaden oil (15-30) Myrica carolinensis (-€lo),Ochna sqarrosa (-73, Rhus succedanea (-70) lard (16-24), tallow (15-30) Canarium schweinfurthii (85), Garcinia species (60-65) peanut oil (5-7), milk fat (2-4) nephelium species (>30) peanut oil ( 5 4 , mustard seed oil (11,s) lophira species (20-35), Psochocarpus tetragonolobus (-20) peanut oil (13), mustard seed oil (Il), adenanthera pav. (-30), eleagnus angustifolia (-2O), tamarindus indica (-20) pentachletra macrophyllia (-5), rumex pseudonatronatus (-3), vermonia anthelmica (-3) Continued
65
Composition, Structure, Physical Data, and Chemistry
TABLE 2.7 (Continued) Monounsaturated fatly acids Occurrence in common oils and fats CnH2n02 n Trivial name Sources with remarkable proportion (YOof total fatty acids) 12 14
Lauroleic Myristoleic
16
Palmitoleic
18
Oleic
18 18 18 20 20
Elaidic Petroselin ic Vaccenic Cadoleic Eicosenoic
22
Erucic
sperm whale oil (4), thohaku nut oil milk fat, tissue fat, liver oil ( I l ) ,whale oil (2,5), sperm whale oil (14) pygnantus kombo (20-23) milk fat, tissue fat (<5), fish oil (go), whale oil ( I 1 51, sperm whale oil sinuata (-70), doxantha unguis (-65), plumeria alba ( ~ 2 7kermadecia ) (55-60) rapeseed oil (LEAR 55-65), peanut oil (45-65), sesame oil (35-50), corn oil (40-50), olive oil (55-85), goose fat (50-65) amaranthus trivolor (-go), garcinia multiflora (-88), corylus avellana (-85) body fat of ruminants Apium leptophyllum (-85), Deverra aphylla (-85), Umbelliferae (1 8-70) butter fat (<2.5), beef tallow sperm whale oil (519) jojoba oil ($30), mustard seed oil 6131, cod-liver oil ($14) Limanthes species (60-75) rapeseed oil (HEAR 40-65), mustard seed oil (I501 Crambe abbessynicum (-60), hispanica (-55)
Polyunsaturated fatly acids Occurrence in common oils and fats CnH2n02 n x Trivial name Sources with remarkable proportion (O/O of total fatty acids) 18
4 Linoleic
18
6 Linolenic
18 20 20 22
6 8 10 10
Elaeostearic Arachidonic Timnodonic Clupadonic
22
12 Cervonic
safflower oil (<80), sunflower oil (S75), poppy seed oil (<65) Myrianthus species (88-94), betula platyphylla (-88) herring oil (go),menhaden oil ($30), linseed oil (f47) Acacia lenticularis (-801, Euphorbia species (75-78); (-linolenic: barley 1-2) Aleuritis species (65-851, Parinarium excelsum (-60) cod-liver oil (125), herring oil (I30), menhaden oil ( 9 9 ) fish oils, fish liver oil cod-liver oil (celO), herringoil (-23), menhaden oil (<12), sardine oil (S14) fish oils
Special fatty acids n Trivial name
Occurrence in common oils and fats Sources with remarkable proportion (% of total fatty acids)
18 24 24 24 24
castor oil (I951 tunny oil brain cerebrosides (701, cardamine graeca (> 50), tropaeolum spp. (> 40) brain cerebrosides (15) brain cerebrosides (12)
Ricinolic Nisinic Nervonic Cerebronic 2-Hydroxynervonic
~~
aFor the fatiy acid composition of thousands of fats and oils of animal and vegetable origin, see among others Hilditch and Williams (1964) and Ucciani (1995).
66
Fats and Oils Handbook
Fatty acids that do not occur in edible fats and oils (with a few exceptions) are not dealt with in this chapter. Detailed information is given by Hilditch (1964) and Geigy (1%8), for instance.
2.2 The Structure of Triglycerides After it had been generally accepted at the beginning of the 20th century that oils and fats were composed of three identical fatty acids bound to one glycerol molecule, it was later found that in reality mixed glycerides predominate (if not, the fatty acid composition does not allow for their formation). Assuming as a model a fat that consists simply of two fatty acids A and B, only two main possibilities exist to distribute these acids to the glycerol molecule (G): (i) Assume that only single-acid triglycerides are formed, resulting in GA, and GB,; (ii) allow for all possible combinations, yielding GA,, GA2B, GAB, and GB,. In the second case, structural isomers of GAzB and GAB, have to be added, namely, (iii) GAAB, GABA and GBAA as well as GBBA, GBAB and GABB. Taking the possible distributions of these two fatty acids A and B on the glycerol molecule, three theoretical models occur that have been the basis of all research about interesterification. These models assume even distribution, minimal distribution, and statistical distribution of the fatty acids in the triglycerides. Assuming even distribution (Fig. 2.5) means that every triglyceride contains one of the two different fatty acids, as long as supply lasts. The model also says that only two different triglycerides exist at the same time but that all four structures given (ii) exist, across the whole range between 0 and 100% of each of the acids A and B. For example, with one third of all acid being A, the mixture would exclusively be 100% GAB,; with one half of all acids being A, it would consist of 50% each GAB, and Proportion of triglyceride type
[%I
0 33.3 66.7 Proportion of fatty acid B (fatty acid A-100-6)
100
[mol%]
Fig. 2.5. Triglyceride distribution of di-acid triglycerides assuming even distribution.
Composition, Structure, Physical Data, and Chemistry
67
GBA,, no other triglycerides being present. Following the model of minimal distribution, only the two single-acid triglycerides GA, and GB, would exist. Their share in the mixture would be equal to the share of the fatty acids A with respect to B (Fig. 2.6). If the triglycerides were synthesized in v i m , the minimal distribution would certainly be excluded for theoretical reasons. The carbon chains of fatty acids are not very voluminous and because they are very similar to each other (except for the chain length), no special distribution would clearly be preferred for steric reasons. Chemical synthesis would lead to almost statistical distribution. That indicates that the probability of occurrence of the four triglycerides GA3, GA2B, GAB,, GB, from (ii) with their isomers (iii) and their relative share of the mixture should be in proportion to the share of A and B in the mixture (Fig. 2.7). Further, it would predict that the acids should be equally distributed to the three positions 1-, 2- and 3of the glycerol molecule, although a differentiation between the 1- and 3-position would not be possible. These distributions, derived from purely theoretical considerations, do not occur in nature because the synthesis of fats does not follow statistical approaches; rather, it is carried out by enzymes whose highly specific catalysis of reactions is determined by blueprints anchored in the genetic information of the animal or plant. Apart from new varieties or new crop species, the genetically steered fatty acid distribution of natural fats and oils can be influenced only to a very limited extent (climate, feeding). One of the proofs for a nonstatistical blueprint is that a natural triglyceride has been found that consists of three saturated fatty acids even when the total of saturated fatty acids is <25%. A significant amount of work has been done to determine the pattern of triglyceride composition or at least some basic principles. Methods to calculate the fatty acid distribution in oils and fats have been given by Litchfield (1973). Mattson and Volpenheim (1961) and Proportion of triglycerlde type (961
60 -
0
33.3
66.7
100
Proportion of fatty acid B (fatty acid A=l00-B) [rnol%]
Fig. 2.6. Triglyceride distribution of di-acid triglycerides assuming minimal distribution.
Fats and Oils Handbook
68
0
25
50
75
Proportion of fatty acid 6 (fatty acid A=100-B)
100 [mol%]
Fig. 2.7. Triglyceride distribution of di-acid triglycerides assuming statistical distribution. Mattson (1963) confirmed the correctness of earlier work from a sample of 30 vegetable oils and fats, describing a predominant distribution of c16:O and C18:ofatty acids to the 1- or 3-position. Analyzing these results, it is evident that in vegetable oils and fats, saturated fatty acids are esterified to the 1- and 3-position as long as this position is available. After that, the residual fatty acids are statistically distributed over the free positions. As a result, the 2-position is occupied mainly by unsaturated fatty acids (Mattson 1963). Apart from its influence on the physical properties, the position of the fatty acids in the molecule also allows a distinction to be made between vegetable and animal fats. In animal fats, the synthesis of triglycerides does not follow the above pattern. Therefore the 2-position is not under proportionally occupied by saturated fatty acids. On the contrary, a slight preference for saturated fatty acids in that position can be found. As a result the ratio of c16:oin the 2-position to total c16:ois significantly different in vegetable and animal fats (Table 2.8). The significant difference between the ratio for vegetable fats and oils (50.3) and the one for animal fats (10.5) is also evidence for the thesis that statistical distribution of the fatty acids does not occur in nature, but that the distribution is genetically steered. From this evidence, Kartha (1962) developed a model that combines statistical and even distribution. This so-called restricted statistical distribution reflects reality much better (Fig. 2.8) than any other model. However, only a few fats come close to this model. The Kartha model corresponds very well to the analytical data for linseed oil or apricot kernel oil. For other oils, deviations from the model must be stated; however, in some cases, these are minor deviations only, and no other model are has been able to come as close to reality.
Composition, Structure, Physical Data, and Chemistry
69
TABLE 2.8 Ratio of Palmitic Acid in 2-Position to Total of Palmitic Acida Ratio (mol %) C16:O in 2-position C16:O total
Oil
0.07 0.08
Cottonseed Olive Peanut Rape Soybean Sunflower Palm
0.08 <0.10 0.1 7 0.1 7
0.25
Fat Cocoa butter Coconut Beef tallow Mutton tallow Lard
0.07 0.1 3 0.47 0.50 0.80
aSources: Mattson (1958, 1953 and 1964), Litchfield (1970 and 1971) and Gunstone and Padley (1965).
To estimate the physical properties of fats and oils, the triglyceride composition is important. According to the purpose of the characterization, the triglyceride composition can be globally indicated by the sum of the chain lengths of the fatty acids esterified to the glycerol or by the sum of double bonds of the whole triglycProportion of triglyceride type
100 80 60
n I
\
[%I
/
40 20 0 0
25
50
75
100
Proportion of fatty acid B (fatty acid A-100-8) (rnol%]
Fig. 2.8. Triglyceride distribution of di-acid triglycerides assuming restricted statistical distribution (after Kartha 1951).
70
Fats and Oils Handbook
Fig. 2.9. Triglyceride composition of vegetable oils (after Litchfield 1973).
eride (Figs. 2.9 and 2-10>.Also, detailed analyses with identification of the three fatty acids exist (for individual oils/fats see Chapters 3 and 4).
2.3 Physical Characteristics The physical characteristics substantially influence the properties of use of oils and fats; chemical properties are of comparably much lower importance because they
Fig. 2.10. Triglyceride composition of fats and oils (after Litchfield 1973).
71
Composition, Structure, Physical Data, and Chemistry
are more important for stability. For a complete understanding of oils and fats processing, knowledge of the physical properties is also important. Melting points and crystal modifications influence fractionation and margarine production; specific density and heat, viscosity and heat of crystallization are of interest for plant designs; structure of triglycerides is required for interesterification; knowledge of solubility is essential for oil extraction and wet fractionation; and vapor pressure and boiling points are needed for deodorization. Physical data are given in the following paragraphs (those that are of specific interest for a certain process only, see the relevant chapters). 2.3.1 Melting Point and Crystal Modification
For fats that require special characteristics (e.g., extra plasticity) and to be able to process them (in margarine making for example), a knowledge of crystal modifications is of importance. Triglycerides exist in three polymorphic modifications, called the a-,p- and P’-modifications. Using infrared (IR) spectral evidence, Chapman (1957b and 1960) classified the crystal structure as follows: a-hexagonal, p-triclinic, and p’-orthorhombic. As with all other polymorphic substances, fats change conformation at specific temperatures. Thus, they follow the path from the thermodynamically least stable to the most stable structure. There is also an amorphous, glasseous form that originates from chilled melts. It is called y-modification. From there, the a-fonn is reached, passing into p’ and p. The transition between modifications is irreversible because their melting points are quite different; an example is shown for single-acidtriglycerides in Table 2.9. Other authors give slightly different values; however, these do not change the picture substantially. TABLE 2.9 Melting Points of the Different Crystal Modifications of Single-Acid Saturated Triglycerides GA3a Melting point of modification (T)
Fatty acid
A
c 8:O c1o:o c12:o c14:0
C160 Cl8:O C18:l CK:, c1&3
C20:O C22:l
a
B’
B
-1 5 15 33 45 55 -32 -45 -44.6 62 17
-2 1 18 35 46.5 56.5 65 -1 2 -1 3 69 25
8.3 31.5 46.5 58 63.5 73.1 4.9 -1 3 -2 4 78 30
aSources: Loskit (1928),Clarkson and Malkin (1934), Wheeler (1940L and Wan (1 991 ).
Fats and Oils Handbook
72
Similar effects can be observed with bi-acid symmetrical triglycerides (characterized as GA,B) showing fairly large differences in their melting points (Table 2.10). The tables show that not only do melting point differences decrease absolutely in the sequence y + p’ 3 p, but also relative to each other as chain length increases. The respective modification influences the crystallization behavior, e.g., speed of nucleation and crystal growth (seeChapters 6.2 and 8). Riiner (1970) shows the transition between modifications in the cooling curves of a hardened oil and a fat (Fig. 2.1 1). The points of the first (TI) and second (T,) deviation of the lines emphasize the building temperatures tl of a-crystals from the melt and the transition temperature from a - to p’-modification. The points, T,and T,, differ from oil to oil (Table 2.11). In mixed-acid triglycerides, the melting point depends not only on the fatty acid composition, but also on the position to which the fatty acids are esterified. For bi-acid triglycerides, a different picture results from the position of the acid A in GAB,, i.e., in the 1- (3-) or 2-position. This determines whether the triglyceride is symmetrically built or not (Table 2.12). Numbers in the diagonals of the two parts of the table stay the same, of course, because they represent single-acid triglycerides that are exactly the same. For distearates with different second fatly acids, this relationship is graphically shown in Figure 2.12. The difference between the melting points of bi-acid triglycerides may be as great as 17°C; however, the values are very different for different acid combinations (Table 2.13). A similar scatter range as that for saturated acid triglycerides is observed for those containing mono- and di-unsaturated acids. Table 2.14 shows the numbers for triglycerides composed of two equal saturated fatty acids ( S ) and TABLE 2.1 0 Melting Point of Di-Acid Symmetrical Triglycerides CBAB and GABA (A = Palimitic or Stearic Acid) in Relation to the Crystal Modification and the Chain Length of the Acids A and B Melting point (“C);fatty acid A in BAB (2-position)
Fatty acid B2 (1,3-)
A = palmitic acid (C16:o) trigyceride modification
A = stearic acid (Cley0) trigyceride modification
Y
a
p’
P
Y
a
p
c12 c14
6 19 38
50
40 45.5 60 65.5 68
5 21 33 49
Cl8
36 42.5 55 56.5 64
34 38
cl 6
27 35 49 45 56
40 43 53 65 65
44.5 61.5 55 68 72.5
53 58 59.3 64 65
57 60.5 63.8 68 72.5
ClO
c12 cl 4 cl 6 C18
59 55
P
Melting point (“C); fatty acid A in ABA (1,3-position)
B (2-) Cl 0
-
47
’
20 34 37
49
42 47 46 45 59
48 50 55 56.5 65
51.5 53.5 60 65.5
68
30 36 44.2 50
-
47 52 56.6 56 55
Composition, Structure, Physical Data, and Chemistry
Temperature ["C]
\+IT
["FI
Ranasaad \Coolingnil
0
5
73
Rate
10 15 20 25 30 35 40 45 50 55 60
1
t -At1
I '2
Time
Iminl
Fig. 2.11. Cooling curves of palm kernel and hardened rapeseed oil (after Riiner 1970).
one unsaturated fatty acid (U) in different positions. In addition to the heat of fusion when melted, there is heat of transition when the fat crystals transform from one to the other crystal modification. Charbonnet and Singleton (1947) give these values for single-acid triglycerides that may indicate an order of magnitude (Table 2.15). The transition time from one crystal modification to the other has been measured by Sat0 and Kuroda (1987) for tripalmitin, dependent on the temperature in an interval from 42 to 52'C. The melting points of the modifications were a = 45'C, P' = 56.5"C and P = 65.5"C. Figure 2.13 shows the transition as follows: from the molten state via all modifications to the P-modification (liquid 3 solid) from a-to p-crystals in solid state (solid + solid) from the molten state of a-crystals to P-crystals (liquid + solid) from p'-to P-crystals (solid a solid) They found that crystal formation for each modification is much faster than the transition of this crystal modification into the more stable one at that temperature. The transition time from a- to P'-modification is described by Riiner (1970) for native and hardened fats. The ordinate of the graph (Fig. 2.14) shows the lifetime of the a-modification. The bars parallel to the abscissa represent these lifetimes; their endpoints show the melting points of the a-form (left endpoint) and the v-form (right endpoint). Transition temperatures are marked on the line TT. The influence of the composition of triglyceride mixtures on their melting and solidification points are shown in Figure 2.15 for the model-system tripalmitidtri-
74
'
Fats and Oils Handbook
TABLE 2.1 1 Transition Points AT, (Melt -+ a-Modification) and AT2 (a + @Modification) and Transition Times At of Fats and Oils Oil/fat
AT1 YC)
AT2 ("C)
33.0 18.0 15.0 30 18 18 19
31.5 16.0 15.0 27.0 18
Beef tallow Cocoa butter Coconut oil Lard Palm kernel oil Palm oil Shea butter Fat (hardened to "C)
AT1
8 14 0 8 0 960 10
<8
15
ATl ("C)
AT2 ("C)
21.5 18.5 26.0 23.0 25.0 29 24
21.5 18.5 26.0 14.0 20.0 24.0 24
Coconut (34) Cottonseed (34) Palm kernel (37) Peanut (33) Peanut (37) Rape (37) Soybean (37)
At (min)
("F)
91.4 64.4 59.0 86 64 64 66
At (min)
AT1
AT2
88.7 60.8 59 80.6 64 ~ 4 6 59 AT2
(OF)
70.7 65.3 78.8 73.3 77.0 84 75
0 0 0 23 13 10 0
(OF)
(OF)
70.7 65.3 78.8 57.2 68.0 75.2 75
aSource:Riiner (1970).
TABLE 2.1 2 Melting Point of the &Modification of Saturated Di-Acid Triglycerides GAB2 in Relation to the Chain Length of the Acid A in 1- or 2-Positiona Fatty acid B i n BAB c4 c6
Melting point ("C); fatty acid A in BAB (2-Position) being c6
c4
m -1 4.G
[ -25
oa
-1.2a 18.7a 38.8 40.1 44.5a 53.1
a Oa
c16 Cl8
Fatty acid B in ABB c6 C8
ClO c12 c14 c16
C18
c10
a Oa
<
-5.0a 8.3 20 30.2 42.5 48.5a 51.8
4.P 15.0a 31.5 38.5 43.5 51.5 57
I
c
c12 c14
noa
c8
-1 1 .oa 43.5a 46.5a 54.8
I 1
1 [
c14
c12
1 I
-1 la 4.0a 21.0a 37.5 46.5 50 53.5 60.5
1 I
3.7a 11.0 25.P 34 48 57 60 63.8
c16
j
1
18 18.la 28.0a 40 45.5 60 65.5 68
c18
1 1
15 32 32 44.5 61.5 55 68 72.5
1
Melting point ("C); fatty acid A in ABB (1-Position) being c4
-1 1 .oa 14.02 36.0a 40.03 43 49
Talcdated by Werdorp.
ClO
c6
&I\
c12
~~~~~
27.0a 34.0a 39 21.2
29.0a 38.0a 48.P 32
34.5 35
46.5 43.5 46.5 45
!F giF , c14
~
c16
c18
i.6,
46.5 54 56
65.6 62.5
65.0 72.5
75
Composition, Structure, Physical Data, and Chemistry
Fig. 2.12. Influence of the fatty acid A on the melting point of the symmetrical triglycerides C,8-A-C18and the unsymmetrical 1 8-CI8-A (after Bailey 1950).
laurin. Theoretical (---) and measured (-) values are compared. In this mixture, the highest depression of the melting point is found at 28% trilaurin. Natural fats and oils, however, are such complex mixtures of different triglycerides that a multitude of effects superimpose upon each other so that individual effects can scarcely be seen. If the amount of crystallizing matter is graphically shown against crystallization time, an S-shaped curve is obtained. Berg and Brimberg (1983) explain this curve, two straight lines connected by an intermediate line, with the kinetics of the process. According to their investigations, crystallization begins with the formation of small crystals (phase I); later these crystals agglomerate (phase II). This is equivalent to flocculation in dispersions and can be described with the same mathematical equations. The crystal flocculates grow and then crystal growth starts again (phase III). TABLE 2.1 3 Difference in Melting Points (“C) of the Positional Isomers of Saturated Di-Acid Triglycerides GA2B Between Positions 1- or 2- of the Fatty Acid B Fatty acid A, in GA,B Fatty acid B
Cl 0 0
C12:O
c14:0
cl 6:O
C18:O
c6:0 G O
24.1 8.3
6.2 1.7 3 .O
6.0 4.5 0.0 3.5
16.0 23.5 6.0 0.5 3.0
9.1 4.2 6.0 1.8 1.8
Cl 0 0 C12:O c14:0
C160 c16:0
7.5 0.5 5.0 3.5
4.5 2.0 16.5
6.0 1 .o
3 .O 5.5
Fats and Oils Handbook
76
TABLE 2.14 Melting Points of the P-Modification of Di-Acid Triglycerides in Relation to the Position of the Unsaturated Acid Ua Unsaturated fatty acid U In USS (1-position) being In SUS (2-position) being Oleic Elaidic Linoleic Oleic Elaidic Linoleic
Saturated fatty acids S2 C8 C l0
-1 4 4 16 25 34.8 38.5
c12 c14
c16
C18
3 15 27 39.5 50.2 61 ,1
-12.5 -0.5 15.5 20.5 26.5 32.5
-1 3 6.2 16.6 26.5 37.5 44.3
-5.6 0.5 6.5 13.5 19 23.5
c12 c14
cl6
Cl8
41 25 35.5 40 40.3 59.6
-1 7.0 -2.0 11.0 21.3 28.5 41.5
In USU (1.3-position)
In SUU (1.2-position)
Fatty acid S C8 ClO
15.9 25.8 36.6 46.1 55 61
u0
4.2
NO
0
-1 1.5 -8.5 -3.5 5.5
5.6 12 19.6 23.9
34.0 35.4 38.7 43.0 44.5 50.1
-1 0.0 -1 0.0 -7.3 -3 .O -2.2 7.0
aCalculatedby Wesdorp.
Essential for the production of fat and fat products is their crystallization time, the time that determines the necessary residence time in a cooler (crystallizers, see Chapter 8.2). For the time span between reaching crystallization temperature and the beginning of crystallization, Blanc (1969) gives the following values: coconut oil lard shea butter
3 min 14 min 45 min
palm oil (hardened) palm oil
5 min 27 min
Crystal modification also influences the specific density. For example, Wan (1991) gives the following values for tristearin: d3,a = 1.014,d3&' = 1.017, and d3,P = 1.043. TABLE 2.1 5 Heat of Transition from a-to P-Modification of Saturated SingleAcid Triglyceridesa Trical/g
I&
kcal/rnol kJ/rnol at (OF) at ("C) aSource: Charbonnet (1947).
rnyristin c14:0
palrnitin Cl60
stearin Cl8.0
-12.6 -52.75 -9.1 1 -38.14 90.0 32.3
-1 3.3 -55.68 -1 0.74 -44.97 112.5 44.7
-13.7 -57.36 -12.21 -51.12 129.2 54.0
77
Composition, Structure, Physical Data, and Chemistry
42
43
44
45
(108°F)
46
47
48
Temperature
49
51
50
["C]
52 (1 26°F)
Fig. 2.13. Transition times from a- to P'-modification in tripalmitin (after Sat0 and Kuroda 1987).
2.3.1.7 Melting Points of Mono- and Diglycerides. Melting points o f monoand diglycerides (that are produced from fats, see Chapter 8.9) lie 10-20°C above those o f their source fats. They follow a uniform pattern. Table 2.16 gives some examples. It can clearly be seen that melting points rise following the line tri-,di-,
Lifetime of (y -modification [min] Peanut oil
m
Rape 39
A
25 Rape 37 Cocoa bMer
15
Shea butter'
Cottonseed 33 Sunflower 33 Soybean 37
Tallow
3 TT
-5
10
14
18
22
(50"F) End points of bars:
26
30
34
left: (y --->B '-modification
38
(1 00°F)
["c]
right: melt --->(y-modification
Fig. 2.14. Lifetime of the a-modification of triglycerides as well as transition temperatures (TT) from the melt to the a-modification (right) and from the a- to the P-modification (left) (after Riiner 1970).
Fats a n d Oils Handbook
78
(185.F)
Temperature ["C]
7 * ('(re
74
Trlpalmltln / Tristearin 70 -
Cloud point
(144'F)
t2P..
60 - x[%] = 0
20
40
60
80
100
0
20
40
Palm oteln x) /
Tristearin x) I Tripalmitin (100-x)
Palm kernel OW \lCIO-x)
Fig. 2.15. Melting points and solidification points of the system tristearinkripalmitin (after Joglekar et a/., 1928 and Watson, 1930); cloud point of the system palm olein/palm kernel oil (after Kun and lbrahim 1991).
monoglyceride. Furthermore, the influence of double bonds in the fatty acids can be seen (melting point drops). Mono- and diglycerides are used as emulsifiers. When storing blends of monoand diglycerides with oils (see Chapter 8.4), their significantly higher melting points must be noted in order to keep all components of the mixture liquid, thus avoiding crystallization, separation, and settling of the emulsifier (partial glycerides). TABLE 2.1 6 Melting Points of Single-Acid Mono-/Diglycerides; P-Modificationa Melting point ("C)
Fatty acid C" c6:0
C8:O
c1o:o c1z:o c14:0 cl 6:O
C18:O c18:1 cl 8:2 c18:3
C,-C,-C, -2 5 8.3 31.5 46.5 57 65.5 72.5 4.9 -13.1 -24.2
C,-OH-C,
44.5 57.5 65.5 73.2 78.2 25.8 -2.6 -12.3
C,-C,-OH
-27 40.8 55.5 62.8 71 .O
C,-OH-OH
OH-C,-OH
19.4
-8
40
29.8 40.4 51 61.2 69.0 75.2 23.5 8.9
53 63 70.5 77.0 81.5 35.2 12.3 15.7
aSources: Bailey (1950), Baur (1 949), Eckey (1954), Hartmann (19581, Martin (1953), Chapman (19571, Filer (1946), Daubert and Lutton (1939, 1944 and 1947), Wheeler (1940), Malkin (1936 and 1954) and Henkel and Cie (1971).
79
Composition, Structure, Physical Data, and Chemistry
2.3.2 Other Physical Data 2.3.2.1 Specific Heat. Several equations exist for the calculation of the specific heat. All of them are empirically determined and are valid only for certain fats and oils in a specific temperature range. However, all of them are accurate enough to be used for most common technical applications. These equations have the following form:
C, = a + b x t (caVg)
v.11
In view of the small differences in a, and the minor influence of the coefficient b (Table 2.17), it is clear that such very small differentiation is not necessary to answer the usual questions in fat processing. Usually, accuracy is satisfactory when using one general value calculated for all fats and oils over the whole temperature range. For higher temperatures Bernardini (1985) gives the following data (soybean oil): 100°C C, = 0.580 ( c d g ) = 2.428 (J/g) 150°C C, = 0.589 ( c d g ) = 2.466 (J/g) 200°C C, = 0.626 (CaVg) = 2.621 (J/g) 250°C C, = 0.698 ( c d g ) = 2.922 (J/g) Temperature dependency for other oils is shown in Figure 2.16. 2.3.2.2 Heat of Fusion and Melting Dilatation. More important than the specific heat is the heat of fusion (Table 2.18). It is equal to the heat of crystallization, but inverse in sign. Its estimation is especially important to calculate the heat transfer in crystallizers and scraped surface heat exchangers (see Chapter 8). The heat has to be removed quickly in order to give defined properties to the product. Bailey (1950) prcb posed the following equation to calculate the heat of fusion for single-acid triglycerides:
AH = 3[(n- 2)a + b]
v.21
For triglycerides with different fatty acids, the following then must be valid:
H = 3b + (nr+ nrr+ nlrl - 6)a
~.31
TABLE 2.1 7 Coefficients for Specific Heat Calculation (Equation [2.1]) Appl icabiIity Trielvcerides
Oils Tallow, palm oil, partially hardened oils Fats, iodine value < l o Source: Bakes (1975).
- t ("C) 15
-t
Coefficient (OF)
60
a
b
0.462 0.475 0.458
0.00060 0.00055 0.00070
ao
Fats and Oils Handbook
[J/sl
Specific heat [cal/g]
1
Soybean oil hardened (1.V.=6.&*'*Lintrd/
\
-2.28
Soybean oil
-2.08
1.88 0
80
(32°F
(1 760F)
160
240
(32WF)
(464OF)
Temperature
["C]
Fig. 2.16. Specific heat of oils and fats depending on temperature (after Clark 1946).
where n, is the number of CH2-groups of the fatty acid in position x, a is equal to AH per CH2-group and b is equal to AH of the end CH3-group. The values for a and b in triglycerides are as follows: for the a- and p-forms, a = 0.81 and 1.06, respectively, and p = -1.28 and 4.70, respectively. More detailed tables with the heat of fusion for different triglycerides in all modifications as well as fatty acids, mono- and diglycerides have been compiled Density [g/ml] 0.95
Corn 011, soybean oil, cottonseed oil
Stearic acid
0.80
.% '
a,;-.'
..L.'
-.. . *'.
+extrapolated
0 (32°F)
5q122)
I 0 0 (212) Temperature ("C]
150(302)
200 (392'F)
Fig. 2.17. Specific density of oils and fats (after Noureddini et al. 1995).
Composition, Structure, Physical Data, and Chemistry
81
Volume
I
Fig. 2.18. Dilatation of a "steep" and a "flat" fat.
<---- Temperature c----
by Bailey (1950). During crystallization, energy equivalent to the heat of fusion is set free as heat of crystallization. There is also the heat of transformation from one crystal modification to another. Fats expand during melting. The melting dilatation is -0.15 mL/g. This dilatation is observed not only during melting but also during transformation between crystal modifications (Table 2.19; see also Fig. 2.19). 2.3.2.3 Specific Density and Thermal Expansion. To speed up processes, for ease of automation and to allow continuous processing, gravimetric dosing is being replaced more and more by volumetric dosing. The quantity to be measured, i.e., weight, which is independent of temperature is thereby substituted by the temperaturedependent quantity, i.e., volume. Usually, it is not possible for the oil to flow through TABLE 2.1 8 Heat of Fusion of Saturated Single-Acid Triglyceridesa ~~
.,
Heat of fusion (cal/gl Fatty acid A in GA3 Trig1yceride Tricaprin Trilaurin Trimyristin Tripalmitin Tr istearin
Molecular weight
measured
calculated
C-
(MI
a
P
a
P
1O:O 12:O 14:O 16;O 18:O
554.8 639.0 723.1 807.3 891.5
-
38.9 46.2 50.3 53.1 54.6
27.88 31.77 34.82 37.11 39.02
42.09 46.49 49.88 52.55 54.73
aSource: Charbonnet and Singleton (1947).
34.6 37.4 38.9
Fats and Oils Handbook
82
TABLE 2.1 9 Melting Dilatation of Saturated Triglycerides Melting dilatation of (mV@
C-
Fattv acid A
12:o 14:O 16:O 18:O p 18:O a
Lauric Myristic Palmitic Stearic Stearic
GA2
A
0.144 0.152 0.162 0.1 67 0.1 92
0.1 43 0.1 81 0.186
Source: Henkel and Cie 1971.
the volume meter at always the same temperature without a large amount of expenditure. Modem microelectronics, however, allow the mechanically measured volume data to be processed electronically thus compensating for temperature effects by correction factors. For that pupose the microcomputer is given an oil- or blend-dependent reference table for the relationship between temperature and density. The knowledge of the specific density is, therefore, now more important than before, particularly because even large tables can now easily be stored and handled by modem process computers. Swem (1982) gives the following equation for density: d,, = 0.8475 + 0.0003* SV+ 0.00014 * N
~2.41
where SV is the saponification value and N is the iodine value. More important than the saponification value is the iodine value. Normally, saponification values for oils and fats are quite similar (190 c SV c 210) which Dilatation [mm3 /25g] ’ 005 * 2
Cocoa butter
llllp6 butter
*
Shea butter Beef tallow
Lard Palm oil (Congo)
50 (1 22°F)
45
40
35
30
25
Temperature [“C]
20
15 (SQF)
Fig. 2.19. Dilatation of some fats and oils (after Jurriens 1968).
TABLE 2.20 Specific Density of Common Oils and Fatsa I (at 1S0U59'F)
II (at 4OoU104"F)
Animal oils and fats Butterfat Lard Tallow Mutton tallow Goose fat Bone oil (cattle) Neat's foot oil
0.935-0.943 0.914-0.922 0.9364.952 0.936-0.960 -
0.890-0.893 0.91 3-0.91 8
Fish oils Herring oil Sardine oil !5perm oil Whale oil Cod liver oil Fish oil
0.91 7-0.930 0.92 74.932 0.875-0.890 0.914-0.931 0.921-0.927 -
Triglyceride
111 111 (at 8OoU176"F)
0.89W.904 0.89M.904 0.896-0.904 0.902-0.906 -
-
-
I (at 1SoU59"F)
Vegetableseedo;is Soybean oil Cottonseed oil Sunflower oil Rapeseed oil Linseed oil Mustard seed oil Coconut oil Palm kernel oil Babassu oil
Palm oil Olive oil Avocado oi I Nonedible oils Castor oil
0.900-0.922 Triglyceride
0.922-0.934 0.91 7-0.931 0.92M.927 0.9104.91 7 0.9304.935 0.912-0.921 0.919-0.937 0.925-0.935 0.925 0.921-0.947 0.914-0.919 -
0.95M.974 0.9364.945 111 111 (at 15OU59"F) ~
Tricaprin Trilaurin Trimyristin Tripalmitin Tristearin
8.913 8.801 8.722 8.663 8.632
-
Trioleic Trilinoleic Trilinolenic
aSources: (I) Festschrift Thod, (11) Codex Alimentarius and (111) Kalu and Hamilton (1992).
9.1 62 0.9303 0.9454
II at
(at 20°U680F)
(at 4OoU104"F)
0.919-0.925 0.91 80.926 0.91 7-0.923 0.91 4-0.91 7 0.91 40.922 0.908-0.921 0.899-0.914 0.91 80.922 0.895-0.903 0.91 0-0.91 6 0.91 0-0.91 6
Fats and Oils Handbook
84
results in an effect on the density on the order of tenths of a percent. For a medium saponification value of SV = 200, Equation [2.4] becomes d,, = 0.9075 + 0.00014. V
12.51
In contrast, a change in IV of 60 results in a change in density of 1% and, using volumetric metering, in a mass difference of 1%. This would be the case, for example, when changing from coconut or palm kernel oil to olive or peanut oil. A change to sunflower oil would even result in a deviation of 2%. Formo (1979) showed the density of cottonseed oil (IV = 110) over a greater temperature range (see also Fig. 2.17). According to his findings, the usual equations require the following corrections for oils rich in CI6and C18fatty acids: linseed oil (IV = 190), correction 4.013; soybean oil (IV = 130), correction +0.004;hardened lard and vegetable oil (IV)= 70, correction -0.006; fully hardened oil (IV = lo), correction 4.010. These corrections are valid only for the area of fully liquid oil (melted fats). Assuming the common saponification value for cottonseed oil (SV = 190-200) Formo's data and corrections correlate well with the equation given by Swern. Table 2.20 shows densities customary in the trade, compiled from two sources. A decrease in density is a consequence of thermal expansion. Hannewijk et al. (1964) classified oils and fats and gave the following equations for the expansion E for three classes: General fats and oils Hard fats, palm oil, butterfat Coconut and palm kernel oil Oils
E=K+sx~ E = 20.4 + 0.020~ E = 20.6 + 0.019t E = 19.8 + 0.015t
where E is the medium expansion (mmV25 g), t is the temperature ("C), K is a constant (dependent on oil and respectively fat) and s is the slope of the oil-specific straight line E against t. These equations have been worked out theoretically by applying statistical methods to the data found by Bailey and Singleton (1945) for single-acid triglycerides as model substances. For practical use, it has been proposed to combine Equations [2.7] and [2.8] to yield the following for fats:
E = 20.5 + 0.020t
[2.10]
The slight deviations caused are not significant in practical use. The expansion that follows the above equation can be combined with data for the density to calculate a percentage expansion that gives a much better impression of the order of magnitude of this effect. To obtain exact values, the density of the specific oil must be used. However, to obtain a reliable overview, it makes sense to calculate using a simplified set of data. The density of vegetable oils is -0.920 (2OoC),which leads to the following:
Composition, Structure, Physical Data, and Chemistry
1 g of vegetable oil = 1.087 cm3
85
[2.11]
Taking into account the theoretical expansion from Equation [2.9], the conclusion is as follows:
E = 19.8 + 0.015 x 20 = 20.1
20.1[mm3/(25 g . t)]= 0.000804 [cmV(g . t)]
[2.12]
From this follows the percentage expansion E% per "C for a temperature of 20°C:
E% = 0.000804 x 100/1.087= 0.074
[2.13]
Under these simplifying assumptions, one can say that vegetable oils expand 0.074% per "C at 20°C. Following the same approach, a value of 0.077% per "C is obtained for fats. Baltes (1975) gives 0.00070 (= 0.07%) for coconut oil, 0.00071 for palm kernel oil, and 0.00068 for all other oils as the coefficient of expansion. For small temperature intervals Ar, E can be multiplied by Ar to yield the overall expansion over that temperature interval. Equation [2.6] then becomes
Etota,= At(K + sr)
[2.14]
where EtOd is the expansion over the temperature interval At. Over large intervals, this calculation leads to an error of -lo%, assuming heating from 100 to 200°C. To avoid this error, one must integrate over the temperature interval (b = beginning, e = end).
By integration Equation [2.6] becomes [2.15] After integration,
Etotal = K(r, - fb)
+ s/2(t,2 - rb2)
[2.16]
and, after breaking up (t,2 - tb2),
Equation [2.17] expresses, in a deducted form, something which is logical in a linear relationship such as expansion vs. temperature, namely, that the corrected value over a temperature range tb and re iS equal to the value calculated with the mean value t, of tb and re. Written differently, Equations [2.14] and [2.17] can be
86
Fats and Oils Handbook
compared as follows:
Etotal= Ar(K + sr)
[2.14]
where tMis the arithmetic mean of temperatures tb and te. The above expansion is valid only for oils and totally melted fats. Such equations can also be defined for the temperature ranges in which triglycerides are completely solidified. The resulting straight line (for fats), however, is not a continuation of the line for the liquid state (oils). Both lines are separated by the area of melting dilatation, i.e., the area that is bordered by the melting of the very first parts of the fat and the melting of the very last bit. The two straight lines for liquid state and solid state do not have to be parallel (Fig. 2.18). While the dilatation curve of a more or less single-acid fat is steep those of plastic fats are flat, because of the overlap of melting dilatation of many different triglyceride components. Apart from using melting dilatation for analytical purposes, it also gives information about the characteristics of a fat: the steeper the curve, the narrower the melting range. With a narrow melting range, the heat of melting has to be delivered altogether almost at “one point” of temperature; thus, a cooling effect in the mouth results when the fat is consumed. A good example for steep fats are cocoa butter, illip6 butter, and coconut fat (Fig. 2.19). 2.3.2.4 Vapor Pressure and Heat of Evaporation. To provide the necessary
conditions for deodorization or physical refining of oils and fats, a knowledge of the vapor pressure of the components to be removed is necessary (e.g., fatty acids, aldehydes or ketones). The vapor pressures of fatty acids, single-acid triglycerides and of two oils, shown in Figs. 2.20 and 2.21, differ mainly in that the comparable vapor pressure of the fatty acids is roughly a hundred times higher. In a double logarithmic diagram, vapor pressure vs. temperature would yield a straight line. In addition to the main components of oils and fats, there is special interest in the minor components that negatively influence taste, smell, and keepability. These are usually ketones and aldehydes whose vapor pressure is significantly higher than that of triglycerides and fatty acids (Figs. 2.22 and 2.23). Chemical antioxidants have vapor pressures on the order of magnitude of ketones and aldehydes. In a logarithmic graph, their vapor pressure forms a straight line from almost 0 at 0°C to lo00 mm Hg at 249°C (butylated hydroxyanisole BHA), 262°C (butylated hydroxytoluene BHT), and 280°C (tert-butyl hydroquinone TBHQ). The vapor pressure of natural antioxidants is much lower, e.g., for tocoperols, it is -50 times lower. Eckey (1954) gives the heat of evaporation for single-acid triglycerides (Table 2.21). As a comparison, the heat of evaporation for water is 2.26 kg/g (539 caVg), i.e., approximately ten times as high compared with fats.
87
Composition, Structure, Physical Data, and Chemistry
Vapor pressure [Pa]
10
1
01
00 1 50
90
130
170
210
250
290
330
(122’F)
(194)
(266)
(338)
(410)
(482)
(554)
(626°F)
Temperature [“C]
Fig. 2.20. Vapor pressure of the fatty acids C6 to CI8 (after Monick eta/., 1946).
2.3.2.5 Viscosity. Viscosity of oils, as with most substances, is inversely proportional to temperature. It is also inversely proportional to the number of double bonds of the esterified fatty acids. However, the first double bond decreases viscosity much more than any subsequent one (Fig. 2.24). In logarithmic graphs, the relationship between temperature and viscosity is repre sented by a straight line. This relationship is shown by an equation that has been Trimyristin Tri palmiti n
Vapor pressure [Pa]
10 1
0.1 0.01
Pressures
0.001
are
0.0001 I 140 160 180 200 220 240 260 280 300 320 (284°F)
(446)
(356)
Temperature ~ C I
(536)
(BOBOF)
Fig. 2.21. Vapor pressure of triglycerides and edible oils (after Perry et a/., 1949 and Stage 1977).
aa
Fats and Oils Handbook
Vapor pressure [Pa]
D
A
C
e
0
80
40
(32°F)
120
200
160
240
(392)
(284)
(176)
280 (536'0
Temperature r C ]
Fig. 2.22. Vapor pressure of some components associated with edible fats and oils (after Stage 1979).
deduced empirically by Gouw et al. (1966); as a comparison, viscosity of water at 20.2'C, 68.4'F is 0.1 cP. log (1.2 + log E) = K 0.95 log (1
+ r/l35)
[2.19]
where K is a constant, t is the temperature ('C), and E is the dynamic viscosity (cP). Vapor pressure [Pa]
E
B F
0 B Nonadecenel C Oleatetracosane
E
.
.
' . '
. .'.
Lauricacld
G Palmitic acid
................. . . . . . . . . . . . . .
. . . . . . . . . . .
0 (W°F)
50
100 (212)
150
200
(347)
250
(-1
300
350 (882°F)
Temperature ['C]
Fig. 2.23.
Vapor pressure of some components associated with edible fats and oils (after Stage 1979).
89
Composition, Structure, Physical Data, and Chemistry
TABLE 2.21 Heat of Evaporation of Triglycerides at Their Boiling Point at 0.0014.050 hPad Heat of evaporation
Boiling point ("Cat)
Boiling point ("F at)
Triglyceride
(cal/g)
U/&)
0.05 hPa
0.001 hPa
0.05 hPa
0.001 hPa
Tricapron Tricaprylin Tricaprin Trilaurin Trirnyristin Tripalmitin Tristearin Sovbean oil
58.6 59.1 53.7 48.8 50.9 47.6 44.9 50.5
245.3 247.4 224.8 213.1 204.3 199.3 188.0 209.3
135 179 213 244 275 298 313 308
85 128 159 188 216 239 253
2 75 355 41 5 471 52 7 568 595 586
185 262 31 8 3 70 42 1 462 487
aSources: Perry eta/. (1949), Eckey (1954), Henkel and Cie (1971), and Kalu and Hamilton (1992).
The viscosities of the different seed oils depend on their triglyceride composition; oils with high trioleate content (for example, olive oil or LEAR rape oil) are significantly more viscous compared with oils such as soybean oil (Fig. 2.25 and Table 2.22). 2.3.2.6 Solubility of Oils and Fats and in Oils and Fats. Solubility of oils and fats in solvent plays a role for three processes described later, namely, oil extraction (see Chapter 5.2.3), extraction of oil from spent bleaching earth (see Chapter 7.3.6) and wet fractionation (see Chapter 6.2.2.3). For the separation sharpness of olein and stearin in dry fractionation, the solubility of fats in oils is of some importance. Oils and fats are practically insoluble in water (hydrophobic) and dissolve better in nonpolar than in polar solvents. This is not true for fatty acids, which are also highly soluble in polar solvents, a property that offers the opportunity to wash them out of fats and oils. Only acetic acid and butyric acid are miscible with water in any proportion. From lauric acid onward, fatty acids are insoluble in water. As can be expected, water solubility decreases with increasing (hydrophobic) chain length of the acid.
2.3.2.6.7 Solubility of oils and fats in solvents. The solubility in different solvents covers a broad spectrum. Of course, solubility also increases with temperature. It also decreases with the increasing chain length of the fatty acids. Solubility of lauric acid and myristic acid at 10'C in toluene is A00 and 100 times higher, respectively, than that of stearic acid, for example (Fig. 2.26 and Fig. 2.27). The same tendency noted in fatty acids is also found in triglycerides, Le., the higher the chain length, the lower the solubility (Figs. 2.28 and 2.29). The solubility of fats in oils where oil is the solvent is a very complex process. Therefore, concepts can be developed only from model systems that have ideal
Fats and Oils Handbook
90
Viscosity [cP]
12 Fatty acids
0
t
Z
I
t
!
c18:o
'
l
I
t
1
1
/
I
1
I
I
I
!
I
/
/
10 20 30 40 50 60 70 80 90 100110120 (50'F)
(149)
(104)
(1 94)
(248OF)
Temperature ["C] Viscosity [cP]
25
j Triglyceride : X
Tristearin Tripalmitin
40 45 50 55 60 65 70 75 80 (1M'F)
(131)
(1 58)
*
Trimyristin
A
Trilaurin Tricaprin
85 (1fi'F)
Temperature ["C]
Fig. 2.24. Viscosity of single acid saturated triglycerides (after Joglekar and Watson 1928 and 1930).
composition and allow simplified assumptions. The most substantial of these assumptions is that fat in oil forms an ideal solution, so that no mixed crystals are formed. For such solutions, melting points have to differ by at least 2 0 T , i.e., m.p.oleinc m.p.stearin - 20 = ideal solution. Hannewijk er al. (1964) has investigated the solubility of stearines in oleines (Fig. 2.30). For calculations Clausius Clapeyron's equation is applicable, assuming constant pressure in a monovariant system. The solubility of the high melting compound (stearin) can then be described as:
Composition, Structure, Physical Data, and Chemistry
viscosity
91
[CP]
120
100
Sunflower oil,
80
p.m.: Castor oil 950 (20%) 125 (50%)
------
60 40
20 .O
20 30 40 50 60 70 80 90 100110 (68°F)
(122)
(104)
(194)
(230°F)
Temperature ["C]
Fig. 2.25. Viscosity of oils and fats dependent on temperature. d In m -=-
Qs
dT
R.TM2
[2.20]
[2.20aI
where m is the molar share of stearin in the mixture (gmol,,ea,in/gmolmixtu,),Ts is the melting point of stearin ("C), TM is the melting point of the mixture ("C), R is the universal gas constant, and Qs is the molar heat of melting of high melting component, i.e. the stearin. Assuminn a constant
(3 heinp
0J2.3 . R. eouation 2 20a hacnmec
log m=-C.-
TS TS
'
[2.21]
TM
Assuming concentrated solutions of the high melting component S and a melting point TM that does not differ greatly from that of S,by approximation T, may be regarded equal to Tsin the denominator. Equation 2.21 then becomes log m = K(T- T,) in which
K=-=C Qs Ts2 2.3. R . Ts2
[2.22]
Fats and Oils Handbook
92
TABLE 2.22 Viscosity
of Fats and Some Fatty Acids at Different Temperatures
Viscosity (cP) at "C ( O F ) Oils 20°C (68°F) Rape oil (HEAR) Palm oil Cottonseed oil Peanut oil Sunflower oil Soybean oil Linseed oil Palm kernel oil Coconut oil Castor oil Olive kernel oil Triglycerides Tricaprin Trilaurin Trimyristin Tripalmitin Tristearin
Fatty acids Palmitic acid Stearic acid Oleic acid Erucic acid
90.9 50 82.6 77 63.7 60.7 47.7
-
950 77 60°C (140°F) 7.77 13.59 17.71
-
38°C (100°F)
50°C (112°F) 28 24 25.3 24 21.5 20.5 17.5 17.4-1 8 16.8-1 7.3 123 24
Reference
98.9"C (210°F) 10.3
-
8.4
7.7 7.6 7.3 6.5 6.1 20.1 9.1
-
7 5 T (167°F)
85°C (185°F)
-
7OoC (1 58°F)
14.6 17.6 20.5 23.4 48.9"C (120°F)
I,IV I I,IV 111 I,IV I,IV I,IV II,IV IIJV II,IV III,IV
-
-
VI,VII VI,VII VI,VII VI,VII VI,VII
6.25 9.1 1 11.70 14.67 18.50
5.51 7.22 9.20 1 1.44 14.31
75°C (167OF)
98.9"C (210°F)
-
-
7.10 9.04
17.70 32.30
13.20 22.40
-
V V V V
4.13 5.08 4.03 6.1 8
aSources: (I)Boekenoogen (1935), (11) Formo (1979), (111) Eckey (1954), (IV) Rescoria and Carnahan (1936), Noureddini era/. (1992), (VI) Kalu and Hamilton (1992), and Joglekar and Watson (1928).
M
For such concentrated solutions a linear relationship may be assumed not only between log m and Vr,but also between log m and Tw As said above, the foregoing is only valid for monovariant systems (no mixed crystals former). However, this equation describes reality quite well (Fig. 2.30). 2.3.2.6.2 Solubility of gases in oils and fats. Solubility of gases plays a role during fats and oils processing. Absorption of oxygen is the basis for later oxidation, and the solubility of hydrogen is important for hardening. Oils are sometimes protected by saturating them with nitrogen, which is also used to whip up some end-products. Formo (1979) gives some linear equations for the solubility of gases [volume dissolved at 760 mm Hg pressure in a volume of oil; tc ("C); tF as follows: (OF)]
(i) S(H,) = 0.0295 + 0.000497 . tc (ii) s ( N 2 ) = 0.0590 + 0.000400 ' tc (iii) s ( 0 2 ) = 0.1157 + 0.000443 ' ?c (iV) S(c0)= 0.0890 + 0.000400 ' fc
-
S(H,) = 0.04544 + 0.000895 tF s(N2) = 0.07180 + 0.000720 ' t F s(0,) = 0.12988 + 0.000797 ' fF S(c0)= 0.10180 + 0.000720' fF
[2.23]
93
Composition, Structure, Physical Data, and Chemistry
Solubility In benzene [% w/w]
10,000 : j i Fatty Acid Caprylic
1,000 i j i ~
Caprlnic
100
+
Lauric
A
Myristic
;:: ...
10
Palmitic
: : I
. . ..
... ...
Stearic
1 i. . :. . . ..
... ...
#
0
10
20
30
40
(92'F)
(SO)
(68)
(86)
(104)
50
(122)
60
70
(140) (lSBeFj
Temperature ["C]
Fig. 2.26. Solubility of different fatty acids in benzene (after Bailey 1950).
The solubility of oxygen is one third to two thirds lower in refined than in crude oils (Ah0and Wahlroos 1967); it increases with free fatty acids (FFA), doubling at about 30%FFA. 2.3.2.6.3 Solubility of water in fats and oils and vice versa. The solubility of water in oils is very low. This small amount is normally of no importance in all technical operations, because water either does not disturb the operation or it can easily be removed. Obviously, that is why almost no data can be found in literature Solubility of stearic acid I96 wt/wtl 10,000
Solvent: 'Toluene I
1
1
1,000
+
'""i
+
*
1
(SOY
Cyclohexane
* Benzene
10
0.1 V 10
* 1 ,CDioxane
Acetonitrile Nltromethane
I 20 (88)
30
40
(6'3)
(104)
50
(122)
6q
(140 Fl
Temperature ['C]
Fig. 2.27. Solubility of stearic acid in different solvents (after Bailey 1950).
Fats and Oils Handbook
94
Solubility in benzene [% w/w]
100 Triglyceride Tricaprin +
Trilaurin
* Trimyristin 9
Tripalmitin
10
Tristearin
,
,
0
10
20
30
40
50
60
70
(32'F)
(50)
(68)
(88)
(104)
(132)
(140)
(158'F)
d
Temperature ["C]
Fig. 2.28. Solubility of single acid triglycerides in benzene (after Bailey 1950).
about solubility of water in oil. For winterized cottonseed oil, Parsons and Holmberg (1937) found 0.075% solubility at 0°C and 0.13% at 32.5"Cwith a linear relation between these points. Outside of this range, solubility rises more quickly. As a trend, it is higher in oils with shorter fatty acid chain lengths (e.g., coconut oil) and increases dramaticdly in oils with hydroxyl groups such as castor bean oil.
Solubility of tristearin [% w/w] Solvent +
Chloroformium
* Benzene * Carbondisulfide
* Ethylether +
0.1
,
0.01 0
(32'F)
10
(50)
Ethanol
I
20
(68)
30
(86)
40
(104)
50
(122)
60
79
(140) (158 F)
Temperature ["C]
Fig. 2.29. Solubility of tristearine in different solvents (after Bailey 1950).
Composition, Structure, Physical Data, and Chemistry
95
Solubility [Mol%] 100
+A
PPO in trilinolein
+B
POP in trilinolein
+C SOS in trilinolein +D
hard. peanut oil / LO
+E hard. peanut oil I LO 10
*F
PPP in triolein
+G SSS in triolein +H SSS in trilinolein
1 15
(59’6
25
(77)
35
(95)
45
(113)
Temperature
55
(131)
65
(149
F)
P = Palrnitic acid S = Stearic acid 0 Oleic acid LO= Linoleic acid
[“C]
Fig. 2.30. Solubility of stearins in oleins (after Hannewijk eta/. 1964).
2.3.2.7 Smoke Point, Flash Point, and Fire Point. The knowledge of these data is of limited interest for oil and fat processing because great care is taken to ensure absence of oxygen when working at higher temperatures. The data are of more importance for those working with oil and fat products, e.g., deep frying. The values given differ slightly among the specific oils because their triglyceride composition varies, as expected in a natural product. It is primarily the FFA content that influences all three points substantially, as shown by Bailey (1951) and Morgan (1942); see Fig. 2.31. The fatty acid composition of the oils and fats plays a minor role and is of influence only when shifting towards medium and short chain lengths. Coconut oil, for example has a significantly lower smoke point. The degree of unsaturation does not appear to play an important role (Table 2.23). The term “smoke point” is misleading because there is no smoke, but there are condensed vapors (clouds) of fatty acids and other lipids. At the fire point, the oil is “actively” burning, whereas at the flash point, decomposition products can be inflamed merely when coming in contact with a flame. For shortenings, the following equation for the relationship between FFA content and smoke point has been developed by Zabik (1962):
FFA = 0.0445 - 0.00174 Ts 2 0.018
[2.24]
where FFA is the percentage of free fatty acids and Ts is the smoke point (“(2). The temperatures given should not disguise the fact that, for igniting an oil, how finely it is dispersed, i.e., its surface area, is also very important. If it is very
Fats and Oils Handbook
96
Free fatty acids
[%I
3.01
’09
$$!
(SW 150
(212 F)
$G
$9:
0
Temperature [‘C]
Fig. 2.31. Smoke, flash, and fire point are dependent on their fatty acid content (after Bailey 1951 and Morgan 1942).
finely dispersed, it can ignite or detonate at much lower temperatures when corning into contact with oxygen. This is important when filters in which the oil is finely dispersed on an adsorbent (such as bleaching earth) are opened when still hot. 2.3.2.8 Refractive Index. The refractive index gives the ratio between the angle of incident light and the refracted beam when passing through a medium. Oils and fats may be characterized by the refractive index, and the progress of a chemical TABLE 2.23 Smoke Point, Flash Point, and Fire Point of Fully Refined Oil9 ~
Oil Rapeseed oil Peanut oil - peanut oil - hardened 32/34 Cottonseed oil - cottonseed oil Soybean oil - soybean oil - hardened 42/44 Sunflower oil Coconut oil Palm oil
0.08 0.09 0.1 1 0.04 0.04 0.1 8 0.04
-
0.04
0.10 0.20
0.06
218 207 198 226 223 185 213 242 223 209 194 223
424 405 388 439 433 365 415 468 433 408 381 433
317 315 333 314 322 318 317 330 318 316 288 314
603 599 631 597 612 604 603 626 604 601 550 597
%urces: Rirnpl (1963), Morgan (1942), W i l e r and Markley (1940), and Pardun (1969).
344 342 363 340 342 357 342 360 342 341 329 341
65 1 648 685 644 648 675 648 680 648 646 624 646
-
Composition, Structure, Physical Data, and Chemistry
97
reaction may be monitored by measuring it. Lund (1922) found an equation that allows calculation of the refractive index of oils and melted fats from the saponification value and the iodine value: t ~ D= t X,
- O.oooO8 * SV + O.ooOo107 . IV
[2.25]
where SV is the saponification value, IV is the iodine value, t is the temperature ("C), x, = 1.4686 for t = 40°C and xt = 1.4650 for t = 50°C. According to Pardun (1976), the equation works satisfactorily only when fresh fats of natural'origin are used (i,e., not oxidized or hardened). In analogy to Chapter 2.3.2.3, Equation [2.25] can be simplified to estimate the order of magnitude more easily. Assuming an average saponification value of 200, it becomes the following:
ID' = X , - 0.016 + O.ooOo107 IV
[2.26]
*
or, for the usual measuring temperature of 40"C, [2.27] Tables 2.24 and 2.25 show refractive indices for single acid triglycerides and for common oils and fats. By plotting the refractive.index mean values of the oils and fats (from Table 2.25) against the mean iodine values from the fact files (Chapters 3 and 4), a regression line can be calculated. The boxes symbolize the ranges of iodine values and the refractive index at 40'C (Fig. 2.32). With a correlation coefficient of 0.989, their relationship is represented by the following equation: nD4'
= 1.44764 + 0.0001528 ' Iv
[2.28]
TABLE 2.24 Refractive Indices of Single-Acid Triglycerides GA,a nDX Fatty acid A
A= c6:0 C8:O
Cl0:O Cl2:O c14:0 cl6:O C18:O
C18:l
Cl8:2 c183
n~~Triglyceride CA3
20°C (68°F)
6OoC (140°F)
20°C (68OF)
70°C (1 58°F)
1.4441 1.4480
-
-
-
-
1.4370 1.4402 1.4428
-
1.4169 1.4230 1.4273 1.4309 1.4337
1.4582 1.4699 1.4800
-
-
-
1.4471 1.4548 1.4645 1.4741
-
aSources: Wheeler eta/. (1 9401, Joglekarand Watson (1 928), and Henkel and Cie (1 971).
Fats and Oils Handbook
98
TABLE 2.25 Refractive Indices of Fats and Oil9 Fatloil
nD40
Milkfat Lard Tallow Mutton tallow Pott whale oil
at 4OoC (1 04°F)
1.452-1.457 1.448-1.460 i ,448-1.460 1.448-1.460 1.467-1.475 1.465-1.467 i . 4 5 a i ,466 1.466-1.470 1.472-1.475 1.467-1.469 1.460-1.465 1.465-1.469 1.467-1.470 1.465-1.468
Fish oil Rapeseed oil (LEAR) Cottonseed oil Soybean oil Linseed oil Sunflower oil Peanut oil Sesame oil Safflower oil Corn oil Grape seed oil Walnut oil Niger seed oil Wheat germ oil Rice bran oil Poppy seed oil Mustard seed oil Palm oil Olive oil Avocado oi I Coconut oil Palm kernel oil Cocoa butter Babassu oil Shea butter lllip6 butter Mowrah butter Borneo tallow
-
-
1.449-1.455 1.4677-1.4705 1.448-1.450 1.448-1.452 1.456-1.458 1.448-1.451 1.465-1.466 1.459-1.462 1.458-1.461
-
1.457-1.461
-
1.455-1.458 1.456-1.458 1.470-1.478 1.464-1.466 1.466-1.468 1.465-1.469 1.472-1.475 1.466-1.468 1.461-1.465 1.465-1.468 1.467-1.469 1.465-1.466 1.461-1.471 1.469-1.475 1.467-1.469 1 . m - 1 ,478 1.466-1.469 1.467-1.470 1,463-1.466 1.453-1.456 1.461-1.462 1.461-1.465 1.448-1.450 1.449-1.450 1.456-1.458 1.449-1.451 1.463-1.466 1.459-1.462 1.458-1.461 1.456-1.457
~~
aSources: Left column, Codex Alirnentarius; right column, Wissebach (1969)
2.4 Chemical Reactions
Except for hardening, no purely chemical reactions are conducted in oils and fats processing. However, unwanted nontriglyceride components may be separated by chemical means without affecting the remaining triglycerides. An example are FFA that are saponified by alkali and separated via the aqueous phase. Together with the intentional reactions during processing, a natural product undergoes a broad range of reactions that are triggered or promoted by its natural environment or induced during processing. These reactions are described in the following sections.
99
Composition, Structure, Physical Data, and Chemistry
Iodine value
2ool 200
150
150
loo(. 100
50 0 1.44%
1.453
1.458
1.463
1.468
1.473
1.47%
Refractive index
Fig. 2.32. Relationship between refraction index and iodine value of fats and oils.
2.4.1 lsomerization
2.4.7.1Geometrical Isomerization. Natural vegetable oils and fats contain unsaturated acids almost exclusively in the cis form. At high temperature (around 150"C), with surface active components (such as Kieselgur and bleaching earth) present, and during hardening, these double bonds can be isomerized into the trans form. As mentioned previously, vegetable oils and fats are almost trans free (below detection limit in seeds). Trans fatty acids occur in most animal fats, e.g., in butterfat at a level of 2 . 5 4 5 %(varying between summer- and winter-butter) (Patton et al. 1960). Kaufmann and Mankel (1964) found considerable amounts of trans fatty acids in beef tallow (4.6-lo%),goat (6.8-11.1%)and mutton (10.7-15.8%). 2.4.7.2 Positional Isomerization. As well as geometrical isomerization, positional isomerization can also take place, which means a shift of isolated double bonds toward a structure containing more conjugated double bonds. This isomerization can occur at very high temperatures during alkali treatment. Such conditions do not occur during correct processing of oils and fats for edible purposes.
2.4.2 Polymerization
If fats and oils are heated above 250'C and kept at that temperature, the probability of fatty acid dimerization (intermolecular) or cyclization (intramolecular) increas-
Fats and Oils Handbook
100
es. Because only thermal dimerization can be observed under normal conditions of oils and fats processing, the term polymerization, frequently used for this phenomenon, is misleading. Only in refining are the temperatures applied at levels high enough to reach that range. Therefore, they have to be monitored carefully (see Chapters 7.4 and 7.5). Because the reaction is time dependent, residence time has to be kept as short as possible. Great efforts in recent years have succeeded in drastically reducing dimerization to such an extent that it can almost be avoided in well-run refineries. If oil is kept for an extended period in an open atmosphere at high temperature (e.g., deep frying), oxidative polymerization can occur, as indicated by a deeper color and increased viscosity. In oxidative polymerization, fatty acid molecules are intramolecularly or intermolecularly bound via an oxygen bridge. Splitting off oxygen can lead to cyclization, dimerization and polymerization. Polymerization is technologically used only for oils that are not intended for edible purposes. Tung oil, for example, is polymerized by being kept at 300°C for 12 min; a cross-linked polymer is formed. 2.4.3 Au toxidation
Autoxidation is a radical chain reaction. After an induction period, it may run very fast under certain circumstances. A chemical attack on the alkyl group is followed by a chain reaction, resulting in a hydroperoxide group (-OOH) in the chain. The chain reaction is started by peroxy-, alkoxy- and alkyl-radicals
R-OO', R-O',
R'
[2.29]
The chain reaction proceeds by reaction with oxygen or RH
R' R-00' R-0'
+
O=O
+
R-H R-H
+
+ -+ +
R-00' R-OOH+R' R-OH+R'
[2.30]
It is accelerated by branching of the chain
R-OOH 2R-OOH
-+ -+
R-0'
+
R-0' +
'OH R-OO'
+ HzO
[2.31]
The chain reaction ends by combination of two radicals
R' R' R' R-0' R-OO' R-0'
+ + +
+ +
+
R' R-0' R-OO' R-00' R-OO' R-0'
[2.32]
Composition, Structure, Physical Data, and Chemistry
101
Autoxidation is promoted by heat and light (energy) and heavy metals can catalyze the process. The energy that is needed to split an allyl-positioned H-atom decreases from 99 kcal/mol for the methylene group via 80 kcaVmol for a molecule with one allylic group to 40 kcal/mol for a molecule with three allylic groups. Highly unsaturated oils are especially susceptible to this type of reaction. The hydroperoxides formed (they themselves are almost neutral in taste) react further to aldehydes, ketones and fatty acids, all of which negatively influence taste (see also Equation [2.33]. These are removed during deodorization (see Chapter 7.4). Gunstone and Hilditch (1945) gave the relative reaction rates (R) for the oxidation of oleic acid (R = 1) c linoleic acid (R = 10) c linolenic acid (R = 25). Erickson and List (1985) calculated the inherent stability of common oils and fats, giving reaction rates that are naturally inversely propodonal to the oxidation stability, i.e., the higher the reaction rate, the lower the stability (Table 2.26). Belitz and Grosch (1982) determined the speed of oxidation for unsaturated C,, fatty acids (Table 2.27) and described the oxidation mechanisms. Natural antioxidants in vegetable oils and chelate-building additives, such as citric acids that can bind trace metals, help to avoid oxidation. To prevent metal catalysis of oxidation, processing equipment for fats and oils should not be fabricated in mild steel. However, mild steel can be coated to prevent contamination of the oil by trace metals. This coating can be of synthetic resin or resin from polymerized edible oil. For the latter, the equipment is filled several times with hot oil so that a thin film of polymerized oil resin builds up on the walls as a protectant. Under certain circumstances, lipochromes, natural antioxidants such as carotinoids, can also act prooxidatively under the influence of light. It is therefore recTABLE 2.26 Relative Rates of Reactivity of Common Oils and Fats. Stability Calculated as Decimal Fraction Fatty Acids Multiplied by Relative Rate of Reaction with Oxygen of Each Fatty Acidd Oillfat Safflower oil Soybean oil Sunflower oil Corn oil Rapeseed oil (LEAR) Cottonseed oi I Peanut oil Lard Olive oil Palm oil Tallow Palm kernel oil Coconut oil 'Source: Erikson (1985).
Stability
Iodine value
7.6 7.0 6.8 6.2 5.5 5.4 3.7 1.7 1.5 1.3 0.86 0.27 0.24
149 132 136 128 120 110 100 62 82 50 44 13 8
Fats and Oils Handbook
I02
TABLE 2.27 Rate of Oxidation of Fatty Acidsa C
Fatty acid
Induction period (h)
18:O 18:l 18:2 18:3
Stearic Oleic Linoleic Linolenic
-
Relative speed of oxidation
1
82 19 1.34
100 1,200 2,500
aSource: Belie and Crosch (1982).
ommended that packaging chosen for products containing deodorized oils be impermeable to light or able to absorb those wave lengths that start the oxidation processes. 2.4.4 Hydrolytic Splitting (lipolysis)
Hydrolytic splitting becomes a problem only when microorganisms or enzymes affect fats and oils. Fats and oils are quite resistant against an attack of water alone. However, it has to be taken into account that the activity of microorganisms increases with the water content and is possible only above a certain water content. At 2 0 T , -0.1% of water is soluble in oil, and solubility increases with temperature. Enzymes may arise from the fat itself (in seed oils from the seeds, for example) or from microorganisms that settle on the fat or oil. In particular, molds such as Aspergillus niger, produce high quantities of enzymes. During the sequence of processing steps, hydrolytic attack is a problem only during oilseed storage and transport. After extraction, the risk is low unless storage conditions are poor, because enzymes are usually inactivated by then. In principle, fat can be split more easily if fatty acids are short chained. The enzyme reaction begins with triglycerides because the reaction rate decreases in the sequence triglyceride > diglyceride > monoglyceride. There are unspecific lipases and also others that specifically split certain fatty acids or stereospecifically attack certain positions of the triglyceride (see Chapter 6.4). 2.4.5 Saponification
Free fatty acids react with alkali to form soaps as follows:
R-COOH + NaOH + R-COONa + H,O
[2.34]
The sodium soaps formed are water soluble enough to be separated from the oil or fat as an aqueous solution. As a side reaction, a very small part of the triglycerides is saponified, i.e., hydrolyzed. C3HS(COOR),+ 3 NaOH + C,H,(OH),
+ 3 NaOOCR
[2.35]
composition, Structure, Physical Data, and Chemistry
103
Hydrolysis takes place in three stages; usually the last stage is not reached. For analytical purposes, fats are saponified to determine the unsaponifiable content and to analyze its components (see Chapter 9.5). 2.5 Lipids
Oils and fats contain natural admixtures of nontriglycerides that stem from the seed or pulp in vegetable oils and from the adipose tissues in animal fat. These compounds occur associated with fats and oils in the animal or plant cells and dissolve in the oil. Like the oils and fats themselves, they belong to the large group of lipids. The classification of the compounds said to belong to this group is somewhat artificial and should be viewed from a historical perspective. The usual definition for lipids is that they are insoluble in water but soluble in nonpolar solvents. The group derived its name from its predominant members, fats and oils. In the following sections, the most important groups of lipids that occur in common oils and fats or their sources are illustrated. The following compounds associated with triglycerides belong to this group: hydrocarbons, carotinoids, oil-soluble vitamins, waxes, phospho-, glyco- and sulpholipids. A detailed list of all known lipids including their formula, data and references is given by Gunstone et al. (1986). 2.5.1 Lecithins
Oilseeds contain lecithins whose role is to stabilize the oil, i.e., the energy reserve, in the seeds. During oil extraction, part of these disperse in the oil; usually they are separated and sold as special products. Lecithin was discovered in 181l, when Vauquelin reported fat-containing substances from the brain that contained phosphorous. Schneider (1992) defines lecithin as follows: (i) historical: phosphorous-containing lipid from egg and brain; (ii) scientific: phosphatidylcholine (1,2-diacyl-sn-glycero- 3phosphorylcholine); (iii) commercial and legal: mixture of polar and nonpolar lipids with a minimum of 60% acetone-insoluble substances; (plant and animal origin; European ingredient no. E 322). Schneider also offers the following characteristics: (i) appearance: highly viscous or semiliquid or powder products of brown color; (hydrolyzed, highly viscous or pasty fluids, light brown or brown color); (ii) content: not ~ 6 0 % acetone-insoluble substances; (hydrolyzed, not 4 6 % acetone-insoluble substances); (iii) volatile substances: ~ 2 % determined after 1 h drying at 105°C (221°F); (iv) toluene insoluble: ~ 0 . 3 % (v) ; acid value: <35 mg potassium hydroxide/g; (hydrolyzed, <45 mg potassium hydroxide/g); (vi) peroxide value: 10 or less (mequivkg). The term lecithin encompasses those phospholipids that are found in the oil after extraction. There are three main classes of compounds: phosphatidylcholine (PC), phosphatidylethanolamine (PE), and phosphatidylinosite (PI) (Fig. 2.33). These three classes account for three fourths of all lecithins in soybean oil. Generally, soy lecithin is meant when lecithin is referred to because only soybean oil
Fats and Oils Handbook
104
II CH2 - 0 C - RI
-
Fig. 2.33. Chemical structure of the most important glycerophospholipids. contains substantial amounts (Table 2.28). The production of lecithin is described in Chapter 5.2.5.1. American soy lecithin contains -50% phosphatides, 4 . 5 % glycolipids and the same amount of carhhydrates (Weber 1981).The share of phosphatldylcholine is 4.070of the phosphatides,i.e., 20% of the total soy lecithin. The family of phospholipids houses a great variety of substances because of the very different fatty acid residues (R) and the possibility of binding to two different positions 1- (3-) or 2-. For saturated fatty acids, position 1- (3-) is preferred, for unsaturated, position 2-. Lecithins have many uses (Table 2.29), for example, as emulsifiers for margarines (see Chapter 8.2). Pardun (1988) gives a very detailed description of all aspects of lecithins in a monograph. Crude oils extracted each year contain -850,000 tons of lecithin of which -140,ooO tons are produced. TABLE 2.20 Phosphatides in Oilseeds and Seed Oila Phosphatides (YO) in seedshans
seed oil
Soybeans
1.5
Cottonseed Sunflower seed Peanuts Rapeseed Linseed Corn germs
1.ax2 1.3-2.7
0.5 0.5 1.5 0.75
0.5-1
aSowce: Pardun (1989).
-
-
.o
0.3-0.4 0.2-0.5 -1.8 1-2
Composition, Structure, Physical Data, and Chemistry
105
TABLE 2.29 Use of Lecithina YO
Margarine Baked products, chocolate, ice cream Animal feed Technical products Cosmetics Pharmaceutics
20-30 25-30 25-30 15-20 3-5 -3
aSource: Pardun (1989).
2.5.2 Hydrocarbons Aliphates and terpenoids occur naturally in fats and oils. Polycyclic hydrocarbons can also be found but come from the environment. This is especially hue for coconut oil (see Chapter 4.3.6) whose starting material, copra, is sometimes dried over an open fire. Aliphates and terpenoids are completely removed during fullrefining (seeChapter 7.7). Aliphatic hydrocarbons of natural origin have been identified up to a chain length of Cd5.Usually the chain length is odd-numbered and exists in both forms, unbranched and branched. From the terpenoid family, squalene must be mentioned, because it is contained in substantial amounts in some liver oils. It also occurs in olive oil in remarkable quantities compared with other vegetable oils; it is a marker substance to prove adulteration of olive oil. Squalene consists of six isoprene-units and contains six (all-trans) double bonds. It was discovered by Tsujimoto (1906); see Tables 2.30 and 2.31 and Fig. 2.34. TABLE 2.30 Squalene Content of Some Oilsa Oil Shark liver oil Cod-liver oil Olive oil Rice bran oil Corn oil Cottonseed oil Soybean oil Sunflower oil Sesame oil Linseed oil Peanut oil Rapeseed oil
Saualene Content (Yo) 20-88 0.33 0.090-0.708 0.33 0.0164.042 0.0034.01 5 0.002-0.022 0.008-0.019 0.003-0.01 1 0.004-0.028 0.0024.049 0.003402 8
aSources: Fitelson (1943a), Fabris and Vitagliano (1955), Hadorn (1953), Cracian eta/. (1963)and Tiufel eta/. (1940).
Fats and Oils Handbook
106
TABLE 2.31
Physical and Chemical Data of Squalene (Spinacene) 2,6,10,15,19,23-Hexamethyl-2, 6,10,14,18,22-tetracosahexaene Molecular weight Sum equation Form Iodine value Flash point Melting point ("C) (OF)
Boiling point
(OC) (OF)
Refractive index Density (2014)
WmL)
41 0.74 C30H50
Colorless oil
360-3 80
-200 --75 --lo3 280 at 17 hPa 536 at 17 hPa 1.496520 0.8584
Sources: Neumijller 1993, CRC 1976.
2.5.3 Sterols Sterols are polycyclic alcohols derived from sterane (cyclopentanoperhydrophenantrene) as a base structure. Under the name of sterane, other structures also can be found. Sterols account for the majority of the unsaponifiable fats and oils. Following their natural occurrence, one distinguishes among zoosterols from animal origin, phytosterols from plants and mycosterols from lower organisms such as fungi (Table 2.32). For the biosynthesis of sterols, see Ehrhart and Ruschig (1972). For rape oil, brassica-sterols are characteristic and are used to detect adulteration with other oilsin this case, adulteration of other oils with rape. Phytosterols are not absorbed by the human body, and lower organisms are not yet used as a source for fats and oils; to date, only zoosterols are of importance. However, phytosterols have recently gained attention as food additives in margarine. Table 2.32 gives the sterol content of some oils and fats. The most noted of these is cholesterol (Table 2.34), the first sterol that was discovered. Cholesterol's main source is in food of animal origin and especially animal fat. It is derived from sterol by adding an OH-group to C3, one methyl group each to CISand CI9,and an eight-carbon atom side chain to C,, (Fig. 2.35); physical and chemical data in Table 2.33. Vegetable oils and fats are cholesterol free, following the general agreement that all substances with a cholesterol content 4 0 ppm are regarded as cholesterol free. Cholesterol as a constituent of animal fat is important in so far as it can be linked to heart disease (see Chapter 1.4).
Fig. 2.34. Chemical structure of squalene.
Composition, Structure, Physical Data, and Chemistry
107
TABLE 2.32 Sterol Content (%) of Oils and Fat9 Butter oil Lard Tallow Mutton tallow Fish oil Cod-liver oil Halibut liver oil Herring oil (hardened) Menhaden oil (hardened) Coconut oil Palm kernel oil Cocoa butter Babassu oil Rapeseed oil (LEAR) Cottonseed oil Soybean oil Linseed oil Sunflower oil Peanut oil Sesame oil Safflower oil Corn oil Olive kernel oil
0.24-0.1 4 0.11-0.12 0.08-0.1 4 0.03-0.1 0 0.3 0.42-0.54 7.6 0.6 0.4 0.06-0.08 0.06-0.12 0.1 7-0.20 0.07-0.09 0.35-0.50 0.26-0.31 0.15-0.38 0.37-0.43 0.25-0.40 0.19-0.25 0.43-0.55 0.28-0.38 0.58-1 .OO 0.23-0.30
aSources: Copius Peereboom and Beekes (1 962), Fedeli eta/. (1 9661, ltoh eta/. (1973)and Urakam eta/. (1976).
2.5.4 Lipochromes
At present, more than 550 different carotenoids out of 100 million tons that nature produces every year have been isolated (Rodriguez-Amaya 1993). Carotenoids are derived from a base molecule consisting of a Cd0chain, which is composed from eight isoprenic units. Because of the conjugated double bonds and dependence on the class of substituents, they are colored dark yellow to red. Their absorption maxima lie between 425 and 525 nm. Carotenoids are sensitive to oxygen and light and are natural colorants for food. One distinguishes between a-, p-, and y-carotene (trivial names). a-Carotene contains one a- and one p-ionone ring; p-carotene contains two p-ionone rings; and y-carotene has one additional double bond but only one ring (Fig. 2.35). The main source for a-carotene is palm oil, in which it can account for more than 30% of all carotene contained. Carotenes function as provitamin A. Two molecules of vitamin A can be obtained by symmetrical splitting of p-carotene and the addition of water; a- and y-carotene yield only one molecule of vitamin A. Chlorophyll, another colorant, occurs mainly in those oils that are produced from beans, but also in rape, olive, and avocado oil. Apart from virgin olive oil (as
Fats and Oils Handbook
108
TABLE 2.33 Physical and Chemical Data of Some Sterols Cholesterol
Sterol Chemical formula Molecular weight Form
Density Melting point
C27H460
(g/mL)
PC) (OF)
Boiling point
("Cat hP) ("Flat hP)
386.67 Colorless rhombic or triclinic leaves 1.052 148.5 299.3 233 at 0.5 451 at0.5
Stigmasterol
Campesterol
PSitosterol
C29H480
C28H480
412.71 Colorless crystals
400.72 Colorless crystals
C2gH500 41 4.72 Colorless plates or needles
170 338
157-1 58 3 15-31 6
137-1 40 278-284
a result of the mild refining process), the green color is usually removed by refining. Crude rapeseed oil contains 5-10 ppm chlorophyll, soybean oil up to 1.5 ppm. 2.5.5 Lipovitamins
2.5.5.1 Vitamin A. As seen previously, carotenoids (Table 2.35) can be transformed into vitamin A (Fig. 2.37). Vitamin A (retinol, Table 2.36) itself is usually found in marine liver oils. Quantities can be high (Table 2.37). Deficiency of vitamin A can lead to night blindness or even blindness, with overdosage of vitamin A causing headache and vomiting. It is usually supplied as its acetate or palmitate. A recent overview is given by Woollard (1993) and Furr (1993). TABLE 2.34 Cholesterol Content of Some Oils and Fat9 FaVoil Crude oils Peanut Corn Soybean Olive Rapeseed Sunflower Refined oils Cottonseed oil Coconut oil Palm Palm kernel Animal fat Butter fat Lard ahrce: seher and Cundlach (1982).
Cholesterol (ppm)
10.3 19 7.9 6-7.4 12.5-33.6 1.6-7.7 15.4 5.6 8-2 6 8.4-28.5 2450 980
Composition, Structure, Physical Data, and Chemistry
Cholutro(:
R - H
cnpwkol: R - CH3 Bnuicr(.rm: R - CH3b22 stbmnw: R = 42t1sb22
m:R
H
1 09
= 4 z b
Fig. 2.35. Chemical structure of sterane and cholesterol.
2.5.5.2 Vitamin D. Vitamin D belongs to the family of sterols (Fig. 2.38, Table 2.38). Butter contains 0.0003-0.0015% vitamin D. Vegetable oils and fats and animal fat do not contain vitamin D in amounts worth mentioning. Therefore, vitamin D is added to many fat products such as margarine. Vitamin D deficiency manifests itself by osteomalacy (softening of bones due to insufficient incorporation of minerals), which can lead to deformations if it occurs at a young age. Overdosage leads to vomiting, diarrhea, and in severe cases, kidney damage. An overview on vitamin D is given by Woollard (1993) with the physiologic aspects covered by Maiyar and Norman (1993). 2.5.5.3 Vitamin E (Tocopherol). Tocopherols were first isolated in 1936 by Evans et al. Their structure was described in 1938 by Femholz. To class@ them systemati-
cally, Karrer (1938) introduced the name tocol for the base molecule, 2-methyl-2From this base, all seven known (4',8', 12-trimethyltridecyl)-6-hydroxychromane. tocopherols can be derived. They are built by supplementing positions 5,7 and 8 with one to three methyl groups (Fig. 2.39). The only important ones, however, are the a-, 7- and 6-tocopherols. Tocopherols are used as antioxidants because they trap TABLE 2.35 Physical and Chemical Data of Carotenes
a
Carotene
B
Y
Provitamin A Chemical formula Molecular weight Form Density Melting point
C40H56
C40H56
536.90 Deep purple plates or prisms
536.90 Deep purple hexagonal prisms
(g/mL)
1 .oo
1 .oo
("0
187.5 3 69
183 3 63
("F)
Sources: Roche 1970, CRC 1976, Ceigy 1968, Neurnuller 1987.
C40H56
536.90 Red prisms 177.5 352
Fats and Oils Handbook
110
Fig. 2.36. Chemical structure of the most important carotenoids. OH
Fig. 2.37. Chemical structure of vitamin A.
hydroperoxide intermediates both in vitro and in vivo, thus breaking the chain reaction. The tocopherol content of different oils is given in Table 2.39; an overview is given by Woollard (1993) and Pryor (1993). Table 2.40 presents the physical and chemical data of tocopherols. 2.5.6 Special Compounds of Single Seeds and Oils
Some oilseeds give rise to extracted oils that contain components that make them less suitable for nutrition or restrict their usage in animal feed. There are continuTABLE 2.36 Physical and Chemical Data of Vitamin A (Retinoi, Axerophytol)a Vitamin A Chemical formula Form Soluble in Insoluble in Molecular weight Melting point
C20H300
("C) ("C) (OF)
uvnl,,
C22H3202
Palmitate C36H6002
Yellow crystals
(OF)
Boiling point
Acetate
(nm)
Pale yellow Yellow oil crystal powder or crystal mass Fats and oils, alcohol, ether, chloroform, acetone Water 286.46 328.5 524.9 63-64 57-60 28-29 14547 134.5-1 40 a2-84 1 73-1 38 at l o 6 hPa 343-352 at l o 6 hPa 325 326 326
aOne international unit (1 iu) corresponds to 0.300 pg all-trans-retinolor to 0.344 pg of highly pure retinyl acetate or to 0.549 Fg retinyl palmitate. One retinol equivalent (RE) corresponds to 1 pg all-trans-retinol. Sources: Roche 1970, CRC 1976, Ceigy 1968, Neumuller 1987, Wollard 1993.
111
Composition, Structure, Physical Data, and Chemistry
TABLE 2.37 Vitamin Content of Fish Oils
Liver oil Cod Sea-salmon Halibut Tuna Whale
A (1000 I.E./g) 0.2-1 0 1- 3 2 0-3 00 30-80 30-50
D (i.E./g) 60-300 8C-100 200&4000
-
Source: Baltes (1975).
Fig. 2.38. Chemical structure of vitamins D, and D3.
ous efforts to eliminate such compounds from the seed by new sorts of cultivation. In part, these efforts have already been successful (see Chapter 4.3.5rape), but for other seeds, these restrictions still exist. Some of these compounds are described in the following sections. TABLE 2.38 Physical and Chemical Data of Vitamin D (Calciferol)a ~
~
D2
Vitamin D
(Ergocalciferol)
Chemical formula Molecular weight Form Soluble in insoluble in Melting point
C28H440
396.63
("C)
("0 Sublimation at Density (20/4) ha,
(g/mL) (nm)
Prisms fats and oils (slightly),alcohol ether chloroform water 115-118 2 39-244 0.0006 hPa 1.39920, 264.5
aOne international unit (1 iu) corresponds to 0.025 pg of crystalline vitamin D, or D,. Sources: Roche (19701, CRC (1976), Ceigy (1 968), Neumuller (19871, Wollard (1993).
~
D3 (Cholecalciferol) C29H440
384.62 Needles
84-85 183-1 85
264.5
Fats and Oils Handbook
112
Fig. 2.39. Chemical structure of tocopherols.
2.5.6.1 Sesarnol. Sesame oil contains small amounts of sesamol as well as -0.3% sesamolin, a glycoside of sesamol from which it can be obtained by hydrolysis. Additionally, there is 0.5-1.0% sesamin (Fig. 2.40, Table 2.41). 2.5.6.2 Gossypol. Gossypol is a major pigment in cottonseed and therefore a companion of cottonseed oil. It is a complex phenolic substance (Fig. 2.41, Table 2.42), forming poisonous yellow crystals that cause hemolysis by affecting membrane permeability; it does not appear in refined oil. However, it restricts the use of the meal (see Chapter 4.3.2).A detailed description is given by Marlunann and Rzhekhin (1969). 2.5.6.3 Glucosinolates of Rape. The glucosinolates of rape are derivatives of ally1 isothiocyanate (Fig. 2.42). Immediately after rapeseed has been reduced for extraction, hydolysis of the glucosinolate begins, transforming it into esters of isothiocyanicacid TABLE 2.39
Tocopherol Content of Oils and Fat9 Oh
OiVfat Palm oil Olive oil Soybean oil Cottonseed oil Sunflower seed oil Peanut oil Rapeseed oil Sesame oil Linseed oil Safflower oil Corn oil Palm kernel oil Coconut oil Cocoa butter Babassu oil Lard Tallow Fish oil
a 50-70 80-85 5-1 2 60-80 10-15 50 2-1 5
of Total tocopherols
P 0-6
0-4
-
0-7
-
-
0
0-2 90-95 37-50
0-1
-
-
c60 4-1 5
Y
6
3C-40 0-1 5 60-80 2wo 2-1 0 50 85-98
6-1 0
-
400-700 30-800 920-1800 900-1 100
0-4
500-800
0
15-30
-
0-2
0
95-98 5-6 5M3
0-1 0 0
c20 0-10
<20 75-97
c20
0-4
-
Total tocopherols (PPm)
0
480 800-1 200 188 1 1 0-280 300-3000 200-900 0
80 30-1 30 30 27 10 10
JSources:Lange (1950), Brown (1 952), Schmidt (19681, Taufel and Serzisko (1962), Cracian (19651, Hwrmann and G e m (19821, and Woollard (1993).
Composition, Structure, Physical Data, and Chemistry
113
TABLE 2.40 Physical and Chemical Data of Tocopherolsd Tocooherol -tocol Sum equation Molecular weight Form Soluble in Insoluble in (g/mL) Density Melting point (%C) ('/OF) Boiling point (%C)/at hP (%F)/at hP &ax (nm)
5,8-dimethyl
5,7,8-trimethyl
C28H4802
C29H5002
8- methyl
7,8-dimethyl C28H4802
C27H4602
416.66 Pale yellow viscous oil Oils and fats, alcohol, organic solvents Water
43 0.69
40.264
416.66
0.950 2.5-3.5 3 6.5-38.5 200-222113 39242811 3 294
200-2 1011 3 392-41 0/13 297
-3 to -2 2 6.5-2 8.5 200-2 1011 3 3 9 2 4 1 0/13 298
150176 302176 298
aOne international unit (1 IU) corresponds to 1 mg d!-a-tocopherol-acetate. Sources: Roche (1 970), CRC (1 976), Ceigy (1 968), Neumuller (19871, Wollard (1993).
Fig. 2.40. Chemical structure of sesamol (left) and sesamolin (right).
To prevent the formation of these harmful (for animal feed) substances, the enzyme thioglucosinase is inactivated by conditioning the seed (see Chapter 5.2.4.1). By cultivation of 00-rape varieties, the amount of glucosinates has decreased substantially so that they are now of minor importance. The ally1 isothiocyanates can rearrange to isothiocyanates or thiocyanates or decompose to nitriles and sulfur. A more detailed overview is given by McGregor (1993). TABLE 2.41 Physical and Chemical Data of Sesamol, Sesamin, and Sesamolin Sesamol Molecular weight Sum equation Form Melting point Boiling point
138.12 C7H603
("C) ("F)
("C) ("F)
Colorless crystals 65-66 149-50 135-1Mat 16 hPa 275-284 at 16 hPa
Source: Budkowski (1964), CRC (1976), Neumuller (1987).
Sesamin
Sesamolin
354.34
370.34
C20H1 8O6
CZOH184
Needles 123-1 24 253-255
White plates 93-94 199-201
Fats and Oils Handbook
114
OH
Fig. 2.41. Chemical structure of gossypol.
TABLE 2.42 Physical and Chemical Data of Gossypol 1,1’,6,6‘,7,7’-Hexahydroxy-5,5’-diisopropyl-
3,3’-dimethyl[2,2’-binaphtalenel-8,8’-dicarboxy-aldehyde Molecular weight 518.84 Sum equation Form Melting point
C30H3008
(“C) (OF)
Canary yellow (poisonous) crystals 184 (crystallized from ether) 363
Source: Neurnuller 1987.
Fig. 2.42. Chemical structure of rape glucosinolates. References Aho, L., and Wahlroos, O., (1967) A Comparison Between Determinations of the Solubility of Oxygen in Oils by Exponential Dilution and Chemical Methods, J. Am. Oil Chem. SOC.4 4 , 6 5 4 6 . Bailey, A.E., (1950) Melting and Solidification of Fats, Interscience Publishers, New York. Bailey, A.E., (1951) Industrial Oil and Fat Products, Interscience Publishers, New York. Bailey, A.E., and Singleton, W.S. (1945) J. Am. Oil Chem. SOC. 22, 265. Bakes, J., (1975) Gewinnung und Verarbeitung von Nahrungsjetten, Paul Parey Verlag, Berlin. Baur, F.J., Jackson, F.L., Kopl, D.G., and Lutton, E.S., (1949) J . Am. Chem. SOC. 71, 3363-3366.
Composition, Structure, Physical Data, and Chemistry
115
Belitz, H.-D., and Grosch, W., (1982) in Lehrbuch der Lebensmittelchemie, Springer Verlag, Berlin. Berg, T.G.O., and Brimberg, U.I., (1983) Uber die Kinetik der Fettkristallisation, Fette, Seifen, Anstrichmittel 85, 142-149. Bernardini, E., (1985) Oils and Fats Processing, Publishing House, Rome. Blanc, J., (1969) Techniques modernes de fabrication des margarines, Rev. Fr. Corps Gras 16,457471. Boekenoogen, H.A., (1935) Die Viskositat der fetten Ole, Fettchem. Umschau 42, 177-180. Boekenogen, H.A., (1941) Olien Vetten, Oliezandan 26, 143, from Hilditch, T.P., and Williams P.N., ( 1 W ) The Chemical Constitution of Natural Fats, Chapman & Hall, London. Brown, F., (1952) The Estimation of Vitamin E, Biochem. J. 52, 523-526. Budkowski, P., (1964) Recent Research on Sesamin, Sesamolin and Related Compounds, J. Am. Chem. SOC.41, 280-285. Chapman, D., (1957a) The Structure of the Major Component Glyceride of Cocoa Butter and of Major Oleodisaturated Glyceride of Lard, J. Chem. SOC.1502-1508. Chapman, D., (1957b) Infrared Spectra and the Polymorphism of Glycerides III,Palmitodistearins and Dipalmitostearins,J. Chem. SOC.2715-2720. Chapman, D., (1957~)The 720 cm-1 Band in the Infrared Spectra of Crystallized Longchain Compounds IV, J. Chem. SOC.489-4491. Chapman, D., (1960) Infrared Spectroscopic Characterization of Glycerides, J. Am. Oil Chem. SOC.37,73. Charbonnet, G.H., and Singleton, W.S., (1947) Thermal Properties of Oils and Fats VI, Heat Capacity, Heats of Fusion and Transition and Entropy of Trilaurin, Trimyristin, Tripalmitin and Tristearin, J. Am. Oil Chem. SOC.24, 140-142. Chevreuil, M.E., Recherches sur les Corps Gras, 1823. Chibnall, A.C., Piper, S.H., and Williams, E.F., (1953) Biochem. J. 55,707. Clark, P.E., Waldeland, C.R., and Cross, R.P., (1946) Specific Heat of Vegetable Oils from 0°C to 280°C, Ind. Eng. Chem. 38,350-353. Clarkson, C.E., and Malkin, T., (1934) Alteration in Long Chain Compounds 11: An X-Ray 666-671. and Thermal Investigation of the Triglycerides, J. Chem. SOC., Codex Alimenturius of the Food and Agricultural Organization (FAO), United Nations, Rome. Copius Beereboom, J.W., and Beekes, H.W., (1962) The Analyses of Mixtures of Animal and Vegetable Fats. 111. Separation of Some Sterols and Sterol Acetates by Thin Layer Chromatography, J. Chromatogr. 9, 3 16-320. CRC, Handbook of Chemistry and Physics, CRC Press, Cleveland, Ohio, 1976. Daubert, B.F., and Lutton, E.S., (1947) X-Ray Diffraction Analyses of Synthetic Unsaturated Monoacid Diglycerides, J. Am. Chem. SOC.69, 1449. Detwiler, S.B., and Markley, K.S., (1940 )Smoke, Flash and Firepoints of Soybean and Other Vegetable Oils, Oil & Soap 1 7 , 3 9 4 0 . Eckey, E.W., (1954) Vegetable Oils and Fats, Reinhold Publishing Co., New York. Erikson, D.R., and List, G.R., (1985) Storage, Handling, and Stabilization of Edible Fats and Oils, in Bailey's Industrial Oil and Fat Products, Vol. 111, (Appelwhite, T.H., ed.), pp. 273-3 10, John Wiley & Sons, New York. Evans, H.M., Emerson O.H., and Emerson G.A., (1936) The Isolation from Wheat Germ Oil of an Alcohol, Having the Properties of Vitamin E, J. Biol. Chem. 113,319-332.
116
Fats and Oils Handbook
Fabris, A,, and Vitagliano, M., (1955) Richerche sull’hsaponificabile degli Olii e di Alcuni Grassi; Il Dosamento degli Idrocarburi Totali, dell0 Squalene e delle Sterine, Ann Sper. Agr. Nuova Sene 45,625-659. Fedeli, E., Lanzani, A., Capella, P., and Jacini, G., (1966) Triterpene alcohols and sterols of vegetable oils, J. Am. Oil Chem. SOC. 43,254-256. Fehling, H., (1845) Die Sauren des Cocosnubols, Ann. 53,399-41 1. Filer, L.J., Jr., Sidhu, S.S., Daubert, B.F., and Longenecker, H.E., (1946) X-Ray Investigation of Glycerides 111; Diffraction Analysis of Symmetrical Monooleyl-Disaturated Triglycerides, J. Am. Oil Chem. SOC. 68,167. Fitelson, J., (1943a) Detection of Olive Oil in Edible Oil Mixtures, J. Assoc. 08 Agric. Chem. 26,499-505. Fitelson, J., (1943b) The Occurence of Squalene in Natural Fats, J. Assoc. 08 Agn’c. Chem 26,506-510. Fitelson, J., (1945) Report on (The Analysis of) Oils, Fats and Waxes, J. Assoc. 08 Agric. Chem. 28,282-289. Formo, M.W., (1979) Physical Properties of Fats and Fatty Acids, in Bailey’s Industrial Oil and Fats Products (Swern, D., ed.),p. 188, John Wiley & Sons, New York. Furr, H.C., (1993) Retinol, Physiology, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 3907, Academic Press, London. Geigy, Documents Geigy, edited by von K. Diem and C. Lenmer, J.R. Geigy S.A., Basel, 1%8. Gbbmann, (1854) iiber die Arachinsaure, Ann. 89, 1-1 1. Gouw, T.H., Vlugter, J.C., and Roelands, C.J.A., (1966) Physical Properties of Fatty Acid Methyl Esters. VI. Viscosity, J. Am. Oil Chem. SOC. 43,433444. Gracian, J., Arevalo, G., and Martel, J., (1963) Caracteristicas del Aceite de Oliva de Produccion Nacional; Datos Correspondientes a las Provincias Andaluzas IV,El Indice de Escualeno y su Aplicacion con Fines Analiticos, Grasas y Aceites 14, 101. Gunstone, F.D., (1958) An Introduction to the Chemistry of Fats and Fatty Acids, Chapman & Hall Ltd., London. Gunstone F.D., Harwood, J.L., and Padley, F.B., (1986) The Lipid Handbook, Chapman & Hall, London. Gunstone, F.D., and Hilditch, T.P., (1945) The Union of Gaseous Oxygen with Methyloleate, Linoleate and Linoleate, J. Chem SOC. 836-841. Gunstone, F.D., and Padley, F.B., (1965) Glyceride Studies. Part 111. The Component Glycerides of Five Seed Oils Containing Linolenic Acid, J. Am. Oil Chem. Soc.42,957. Hadorn, H., and Jungkunz, R., (1953) Nachweis und annlhernde Bestimmung von Cruciferenolen in SpeiseBlen nach dem Bleisalzverfahren, Mitt. Gebiete Lebensm. Hyg. 44,453466. Handbook of Chemistry and Physics, (1976) CRC Press, Cleveland, OH. Hannewijk, J., Haighton, A.J., and Hendrikse, P.W., (1964) Dilatometry of Fats, in Analysis and Characterization of Fats, Oils and Fat Products, (Boekenoegen, H.A., ed.), Interscience Publishers, London, p. 118-182. Hartmann, L., (1958) Advances in the Synthesis of Glycerides of Fatty Acids, Chem. Rev. 58,845-867. Hell, C., and Hermanns, O., (1880) Ber. 13, 1713, quoted from Hilditch, T.P., and Williams, P.N., (1964) The Chemical Constitution ofNatura1 Fats, Chapman & Hall, London. Henkel & Cie, (1971) Fettchemische Tabellen, 3rd ed., pp. 44-47.
Composition, Structure, Physical Data, and Chemistry
117
Herrmann, K., and Gertz, C., (1982) Hochdruckfliissigchromatographische Trennung individueller Tocopherole und Tocotrienole in Speisefetten und Speiseiilen an Kunsaulen, Lebensmittelchemie u. gerichtl. Chemie 36,53-58. Hilditch, T.P., (1935) The Fats: New Lines in an Old Chapter of Organic Chemistry:Jubilee Memorial Lecture, Chem.Ind.. 34,139-145,163-167. Hilditch, T.P., and Williams, P.N., (1964) The Chemical Constirution of Natural Fats, Chapman BE Hall, London. Hoerr, C.W., Pool, W.O., and Ralston, A.W., (1942) The Effect of Water on the Solidification Points of Fatty Acids, Solubility of Water in Fatty Acids, Oil & Soap 19, 126- 128. Itoh, T., Tamura, T., and Matsumoto, T., (1973) Sterol Composition of 19 Vegetable Oils, J. Am. Oil Chem. Soc.50,122-125. Iverson, J.L., Eisner, J., and Firestone, D., (1%5) Detection of Trace Fatty Acids, J. Am. Oil Chem. SOC. 42,1063. Joglekar, R.B., and Watson, H.E., (1928) Rysical Properties of Pure Triglycerides, Ind. Inst. Sci. 47,365-368T. Jumens, G., (1968) in Analysis and Characterization of Oils, Fats and Fat Products, (Boekenoogen, H.A., ed.), Interscience Publishers, London. Kalu, C.U., and Hamilton, R.J., (1992) Triglycerides, Structure and Properties,in Enqcropaedia of Food Science, Technology and Nutrition, p. 463 1, Academic Press, London. Kartha, A.R.S., (1951) Studies on the Natural Fats, Ph.D. Thesis, University of Madras, India. M a , A.R.S., (1953a) The Glyceride Structure of Natural Fats. I. A technique for the quantitative determination of Glyceride Types in Natural Fats, J. Am Oil Chem SOC. 30,280-282. Kartha, A.R.S., (1953b) The Glyceride Structure of Natural Fats. II. The Rule of Glyceride Type Distribution of Natural Fats, J. Am. Oil Chem SOC.30,326-329. Kartha, A.R.S., (1954) The Glyceride Structure of Natural Fats. III.Factors Goveming the Content of Fully Saturated Glycerides, J. Am. Oil Chem. SOC. 31.85. Kartha, A.R.S., (1962) Glyceride Type Distribution Rule Calculations, J. Am. Oil Chem. SOC. 39,272. Kaufmann, H.P., (1958) Neuzeitliche Technologie der Fette und Fettprodukte, Mtinster. Kaufmann,H.P., and Mankel G., (1964) h r das Vorkommen von trans-Fettshen, Fette, Seifen, Anstrichmitte 661,613. Kun, T.Y.,and Ibrahim, A., (1991) Palm Olein Improves Cooking Oil Blends, Palm Oil Developments 3, Sept. 1991. Lange, W., (1950) Cholesterol, Phytosterol, and Tocopherol Content of Food Products and Animal Tissues, J. Am. Oil Chem Soc. 27,414422. Lerch, f.U., (1844) h r die fluchtigen Siiuren der Butter, Ann. 49,212-231. Litchfield, C., (1970) Taxonomic Patterns in the Fat Content, Fatty Acid Composition and Triglyceride Composition of Palmate Seeds, Chem. Phys. Lipids 4,96103. Litchfield, C., (1971a) Positional Distribution of Medium Chain Length Fatty Acids in Dicotyledon S e e d Triglycerides, Chem Phys. Lipids 6,200-204. Litchfield, C., (1971b) The Distribution of Oleic, Linoleic and Linolenic Acids in Cruciferae Seed Triglycerides, J. Am. Oil ChemSoc. 48,467472. Litchfield, C., (1973) Taxonomic Patterns in the Triglyceride Structure of Natural Fats, Fette, Seifen, Anstrichmittel 75,223-23 1. Loskit, K., (1928) Zur Kenntnis der Triglynride, 2 physik. Chem. 134,135-155.
118
Fats and Oils Handbook
Lund, J., (1922) Die Beziehungen zwischen den Fettkonstanten, Z. Untersuch. Nahrungs. u. Genubmittel44, 113-187. Maiyar, A.C., and Norman, A.W., (1993) Cholecalciferol, Physiology, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 919, Academic Press, London. Malkin, T., and Shurbagy, M.R., (1936) An X-Ray and Thermal Examination of the Glycerides 11: The a-Monoglycerides, J. Chem. SOC. 1628. Malkin, T., Shurbagy M.R., and Meara M.L., (1937) An X-Ray and Thermal Examination of the Glycerides 111: The a-Diglycerides, J. Chem. SOC. 1409. Markley, K.S., Fatty Acids, Interscience Publishers, New York, 1947 and 1960. Markmann A.L., and Rzhekhin V.P., (1969) Gossypol and Its Derivatives, Israel Program for Scientific Translations, Jerusalem. Marsson T., (1842) ijber Laurin und das feste Fett der Lorbeeren, Ann. 41,329-336. Martin J.B., (1953) Preparation of Saturated and Unsaturated Symmetrical Monoglycerides, J. Am. Chem. SOC.75,5482. Mattson, F.H., (1962) Synthesis and Properties of Glycerides, J. Lipid Res. 3,281-296. Mattson, F.H., (1963) The Specific Distribution of Unsaturated Fatty Acids in Triglycerides of Plants, J. Lipid Res. 4, 392. Mattson, F.H., and Volpenheim, R.A., (1961a) The Specific Distribution of Fatty Acids in the Glycerides of Vegetable Fats, J. Biol. Chem. 236, 1891-1894. Mattson, F.H., and Volpenheim, R.A., (1961b) The Use of Pancreatic Lipase for Determining the Distribution of Fatty Acids in Partial and Complete Glycerides, J. Lipid Res. 2 , 5 8 4 2 . McGregor, D.I., (1993) Glucosinolates, in Encyclopaedia of Food Science, Food Technology and Nutrition, Academic Press, London. Mislow, K., and Bleicher, L., (1954) The Configuration of Cerebronic Acid, J. Am. Chem. SOC. 76,2825-2826. Monick, J.A., Halden, H.D., and Marlies, C.J., (1946) Vapor-Liquid Equilibrium Data for Fatty Acids and Fatty Methyl Esters at Low Pressures, Oil & Soap 23, 177. Morgan, D.A., (1942) Smoke, Fire and Flash Points of Cottonseed, Peanut and Other Vegetable Oils, Oil & Soap 19, 193-198. Neumuller, Calciferol, in Rompp Chemielexikon; p. 557, Frankh’sche Verlagsbuchhandlung, Stuttgart, 1987. Neumiiller, Carotinoide, in Rompp Chemielexikon; p. 609, Frankh’sche Verlagsbuchhandlung, Stuttgart, 1987. Neumiiller, Gossypol, in Rompp Chemielexikon; p. 1543, Frankh’sche Verlagsbuchhandlung, Stuttgart, 1987. Neumiiller, Sesamol, in Rompp Chemielexikon; p. 38 18, Frankh’sche Verlagsbuchhandlung, Stuttgart, 1987. Neumiiller, Squalen, in Rompp Chemielexikon; p. 3941, Frankh’sche Verlagsbuchhandlung, Stuttgart, 1987. Neumiiller, Tocopherol, in Rompp Chemielexikon; p. 4286, Frankh’sche Verlagsbuchhandlung, Stuttgart, 1987. Noureddini, H., Teoh, B.C., and Clements, L.D., (1992a) Densities of Vegetable Oils and Fatty Acids, J. Am. Chem. SOC.69, 1184-1 188. Noureddini, H., Teoh, B.C., and Clements, L.D., (1992b) Viscosities of Vegetable Oils and Fatty Acids, J. Am Chem SOC. 69, 1189-1 191. Pardun, H., (1969) Analyse der Fette und Fettbegleitstoffe, in Handbuch der Lebensmittelchemie, Vol. IV,p. 481, Springer Verlag, Heidelberg.
Composition, Structure, Physical Data, and Chemistry
119
Pardun, H., (1988) Die Pflanzenlecithine, Verlag fiir die chemische Industrie, (Ziolkowsky, H., ed.). Pardun, H., (1989) Pflanzenlecithine - wemolle Hilfs- und Wirkstoffe? Fat Sci. Technol. 91, 45-58. Parsons, L.B., and Holmberg, C.O., (1937) The Estimation of Water in Salad Oil and Determination of Its Solubility at Ordinary Temperatures, Oil & Soap 14, 239-241. Patton, St., McCarthy, R.D., Evans, L., and Lynn, T.R., (1960) Structure and Synthesis of Milk I, J. Dairy Sci. 43, 1187-1 195. Perry, E.S., Weber, W.H., and Daubert, B.F., (1949) Vapor Pressure of Phlegmatic Liquids I: Simple and Mixed Triglycerides, J. Am. Chem. SOC.71, 3720-3726. Propjak, G., Hunter, G.D., and French, T.H., (1953) Biosynthesis of Milkfat in the Rabbit from Acetate and Glucose; the Mode of Conversion of Carbohydrate into Fat, Biochem. J. 54, 238. F‘ryde, E.H., (1985) Fatty Acids, The American Oil Chemists’ Society, Champaign, IL. Pryor, W.A., (1993) Tocopherols, Physiology, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 4575, Academic Press, London. Rescoria, A.R., and Camahan, F.L., (1936) Animal and Vegetable Oils, I d . Eng. Chem 28, 1212. Riiner, U., (1970) Investigation of the Polymorphism of Fats and Oils by Temperature Programmed X-Ray Diffraction, Lebensmittelwiss. u. Technologie 3, 101. Rimpl, E., (1963) personal communication by H. Pardun, Analyse der Fette und Fettbegleitstoffe; Handbuch der Lebensminelchemie, Vol. IV,p. 481, Springer Verlag, Heidelberg, 1969. Roche, Vitaminkompendium, Hoffmann LaRoche AG, Basal, 1970. Rodriguez-Amaya, D.B., (1993) Carotenoids, Properties and Determintion, in Enzyclopaedia of Food Science, Food Technology and Nutrition, p. 707 Academic Press, London. Sato, K., and Kuroda, T., (1987) Kinetics of Melt Crystallization and Transformation of Tripalmitin Polymorphs, J. Am. Oil Chem. SOC.64,124-127. Schmidt, H.E., (1968) Bestimmung von Tocopherolen in Olen und Fetten: EinfluB des Tocopherol-Gehaltes von Erdnub- und Sojaol auf den Oxydationsverlauf dieser Ole beim Erhitzen, Ferre, Seifen, Ansrrichmittel70, 63-67, 159-61. Schneider, M.,(1992) Lecithine-Gewinnung, Eigenschaften und Bedeutung fiir die industrielle Anwendung, Far Sci. Technol. 94, 524-533. Sebedio, J.L., and Ackman, R.G., (1979) Some Minor Fatty Acids of Rapeseed Oil, J. Am. Chem. SOC.56, 15-2 1. Seher, A., and Gundlach, U., (1982) Isomere Monoensluren in PflanzenBlen, Fene, Seifen, Anstrichmittel 84, 342-349. Sieber, R., ( 1995) Konjugierte Linolsauren in Lebensmitteln: eine UbersichtJConjugated Linoleic Acids in Food: a Review; Emiihrungflutrition 19, 265-270. Sigurgislad6ttir, S., and Pglmad6ttir, H., (1993) Fatty Acid Composition of Thirty-Five Icelandic Fish Species, J. Am. Oil Chem. SOC.70, 1081-1087. Sherwood, P.W., (1960) Survey of the Chemical Utilization of Propylene, Ind. Chem. 36, 542-546. Sonntag, N.O.V., (1979) Structure and Composition of Fats and Oils, in Bailey’s Industrial Oil and Furs Products. (Swern, D., ed.), pp. 1-98. John Wiley & Sons, New York. Stage, H., (1977) Feinvakuumdestillationsanlagen im Lichte des Umweltschutzes, Seifen, Ole, Fette, Wachse 103, 151-154,207-210,269-272.
120
Fats and Oils Handbook
Stage, H., (1979) Heutiger Entwicklungsstand der Anlagen zur physikalischen Raffination pflanzlicher Ole, Seifen , Ole, Fette, Wachse 105, 395401. Stage, H., (1982) Moglichkeiten des Umweltschutzes bei der physikalischen Raffbation und Fettsauredestillation, Ferte Seifen Anstrichmitte 841,333-338. Steinberner, U., and Preuss, W., (1987) Glycerin-Ein fettchemischer Grundstoff im Wandel der Zeiten, Fett: Wissenschafr Lutd Technologie 89,297-307. Swern, D. (ed.)(1982) Bailey’s Industrial Oil and Fat Products, John Wiley & Sons, New York. Taufel, K., and Serzisko, R., (1962) Zum Tocopherolgehalt einiger Fette und Ole; 2. Mitteilung: Verteilung der Tocopherole in ausgewwten Produkten, Nahrung 6,413422. Taufel, K., Heinisch, H., and Heimann, W., (1940) Zur Frage der Verbreitung von Squalen in pflanzlichen Fetten, Biochem Z 303,324-328. Thorl, Festschrift “75Jahre mrl”, F. Thorl’s Vereinigte Harburger blfabriken, 1958. Tsujimoto, M., (1906) Regarding Shark Oil, J. SOC. Chem. Ind. Jpn. 9,953-958. Ucciani, E., (1995) Nouveau Dictionaire des Huiles V~g~tales-Compositions en Acides Gras, Lavoisier Tec & Doc, Paris. Urakam, C., Oka, S., and Han, J.S., (1976) Composition of the Neutral and Phospholipid Fractions from Ginkgo Nuts and Fatty Acid Composition of Individual Lipid Classes, J. Am. Oil Chem. SOC. 53,525-529. Volcker, A., (1848) Behenol, Ann. 64,342-346. Wan, P.J., (1991) Properties of Oils and Fats, p. 39 in Introduction to Fats and Oils Technology, AOCS Press, Champaign 1991. Weber, E.J., (1981) Compositions of Commercial Corn and Soybean Lecithin, J. Am. Oil Chem. SOC. 58,898-901. Wesdorp, L.H., (1990) Unilever Research Vlaardingen, personal information. Wheeler, D.H., Riemenschneider, R.W., and Sando, E.W., (1940) Preparation, Properties and Thiocyanogen Absorption of Triolein and Trilinolein, J. Biol. Chem 132,687-699. Wissebach, H., (1969) Pflanzen und Tierfette (ausgenommen Milchfette). Vorkommen, Gewinnung, Zusammensetzung, Eigenschaften Verwendung, in Lebensmirtelchemie, Vol. IV,Fette und Lipoide p. 9-147, Springer Verlag, Berlin. Woollard, D.C., (1993a) Tocopherols, Properties and Determination, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 4569, Academic Press, London. Woollard, D.C., (1993b) Retinols, Properties and Determination, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 3901, Academic Press, London. Woollard, D.C., (1993~)Cholecalciferol, Roperties and Determination, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 912, Academic Press, London. Zabik, M.E., (1962) Correlation of Smoke Point to Free Fatty Acid Content in Measuring Fat Deterioration from Consecutive Heatings, Food Technol. 16, 111.
Chapter 3
Animal Fats and Oils Animal fats can be categorized as milk fats, rendered fats, and fish oils (marine oils). The main representative of milk fats is the fat of cow's milk (milk fat, butter fat, butter oil), All other milks are of almost no importance as far as their fats are concerned. They have their importance as such or as the base for milk products and cheeses. Even when consumed in high tonnages, their fat is not processed separately but as an integral part of that kind of food. Traditionally, the production of butter is a subject of dairy technology. It is therefore described only briefly in Chapter 8. Rendered fats, even if produced in high tonnages, are by-products of meat production. There is no livestock that is bred for its fat. In this respect, rendered fats differ from at least some of the oilseeds, which are grown mainly for oil production with the meal being a by-product. Marine oils are usually by-products of fish caught to be processed as a protein source. However, there are also some fish that are caught with the main purpose of oil production. As a source, a broad spectrum of species from small fish such as sardines to large mammals such as whales is available (in the case of whales, one has to say was available). In total, animal fat production was recorded at -20 MMT (ISTA Mielke 1994), consisting of -7 MMT of tallow and grease, 5.5 MMT of lard, 6 MMT of butter fat, and 1.2 MMT of fish oil. Milk fats, rendered fats, and marine oils differ considerably in their fatty acid composition. Compared with other fats, milk fats contain remarkable amounts of short-chain fatty acids ranging from C4to Clo. Fats from adipose tissue consist of saturated fatty acids, whereas marine oils contain huge amounts of polyunsaturated fatty acids, poly in this case in the real sense of the word, meaning more than three. The fatty acid composition can be influenced to a limited extent by the fodder of the animals. This is especially true for poultry. The linoleic acid content of poultry fat can be increased, for example, by feeding large amounts of grain. Compared with normal feed, lard is softer if pigs are fed mainly with corn or peanuts. However, the potential degree of influence is usually low. As always in nature, there is a striking and interesting example to prove the opposite. The birgus latro crab, which lives in the sea around the Seychelles islands, has as its only fodder the coconuts that have fallen on the beach. The crab's body fat has almost the same composition as that of coconut oil (Hilditch and Muti 1939). The higher the animals stand on the ladder of evolution, the lower the probability that their fatty acid composition will be influenced by their diet. Because fat production is typically only a by-product of meat production, attempts to change the fat composition by changing the feed remained mainly of academic interest. The only exception were trials in the 1970s to increase the linoleic acid content of milk fat in an attempt to avoid the debate concerning the negative influence of milk fat on coronary hem disease. 121
Fats and Oils Handbook
122 Butterfat (milk fat)
Flrh oll
Milk
&
I
1 - 1
1
Buner fst
”
>=--
Tallow, lard
Fish dl
Fig. 3.1. Animal fat production; schematic overview.
In the sections that follow, the fatty acid composition of different fats is given. The sources from which the data were taken are represented by Roman numerals which correspond to the literature index (Chapter 3.4.1). Very detailed information can be found in Hilditch and Williams (1964). The data refmed to as FA0 were taken from the yearly bulletin of the United Nation’s Food and Agricultural Organization.
3.0 Summary Matrices with animal fat are totally different from those of vegetable fats. The adipose tissue of meat stock is used for fat production, whereas a large proportion of the fat remains with the meat and is consumed directly with the meat or processed into meat products such as sausages. In dietetic terms, it becomes “invisible” fat (see Chapter 1.4). Fat from meat stock is produced by rendering and subsequent separation via presses or centrifuges (Fig. 3.1). The residue is dried and used as animal feed. Fish oil production follows the same pattern. The solid residue is dried and sold as fish meal. Butter fat (oil) is produced mainly by melting and clarification of butter.
3.1 Milk Fats
’
In addition to protein and the other components that are necessary for mammals to raise their young, all milks contain fat as a source of energy and as a carrier for fatsoluble vitamins. At first sight, the fat content is not very high (Table 3.1). However, fat accounts for approximately one third of the dry matter. In total, roughly 20 million tons of milk fats are produced per annum (Table 3.2). A majority of the milk fat is consumed with the milk as such or in milk products such as cheese, cream or yogurt. The remainder is used for butter production (see Chapter 8.1). Part of the butter is processed further to butter fat. The fatty acid composition of milks is special in that milks contain relatively high amounts of short-chain fatty acids. Because they can easily pass through the intestinal wall and even be directly resorbed via the portal vein without prior splitting, the short-chain fatty acids are easily digestible for the mammals’ offspring.
Animal Fats and Oils
123
TABLE 3.1 Mammalian Milk Composition (Average over Many RacesBreedsP Fat
Water
Carbohydrates
Protein
Milk
(%)
(YO) (% dry m)b
(YO) ( O h dry m)
(%)
cow Sheep Goat Horse Camel Human
88.5 81.6 86.6 91.1 87.1 87.7
3.7 7.5 4.2 1.3 4.2 4.4
4.6 4.4 4.8 6.3 4.1 6.9
3.2 5.6 3.6
32.2 40.8 31.3 14.0 32.6 35.8
40.0 23.9 35.8 70.8 31.8 56.1
2.1 3.7 1.0
(% dry m)
27.8 30.4 26.8 23.6 28.7 8.1
aSource: Ceigy (1968). b% dry rn, % dry matter.
Milk fats are characteristically different from body fats (Fig. 3.2). The dominating milk is cow’s milk; its fat is considered exclusively in Chapter 3.1.1. Details on the chemical or physical properties of milk can be found in Alais (1961), Kiermeyer and Lechner (1973), Veisseyre (1973, Tape1 (1976), Walstra and Jeuness (1984) and Wong (1988). 3.1.1 Fat of Cow’s Milk (Milk Fat, Butter Fat, Butter Oil)
Milk yield has been dramatically increased in the past 40 years and will be increased further-in some parts of the world also with the aid of hormones. Usually, the increased yield is a result of new breeds and improved feeding. The milk yield of German cows, for example, was 2,600 L per year in 1951; it increased to 4,000 L in 1976 and is >8,000L today. The best cows achieve yields of close to 16,000L. Today, embryos of high-yielding cows can be bought at auction sales. They are implanted into the uterus of other cows, thus ensuring that yield and overall production are increased (Table 3.3). The main “milk countries,” however, can be identified only if production data from the table are brought into relation with 8na or population
-
TABLE 3.2 Milk Producing Stock and World Milk and Milk Fat Production in 1994 Production (miI Iion/MMT)
Nu,mber
Milk
Fat
cowsa Buffalo Shew Goats
225.5 138.4 1 ,145.7 492.2
488.6 48.2 8.0 10.5
16.9 1.8 0.7 0.4
aMilk producing stock only. Source: IAO Production Yearbook 1994.
124
Fats and Oils Handbook
Fig. 3.2. Fatty acid composition of different milks. of a country. If this is done, Denmark and Ireland (not in the table) stand out, countries with >5 million tons of milk per annum and a relatively small population. In the European Community, subsidized overproduction of milk became a severe problem in the 1980s when the so called “butter mountain” reached 1.4 MMT. Fixed subsidies accompanying a milk quota regulation system solved this problem. There still exists some discrepancy between demand and supply between certain regions; however, the overall situation seems to be balanced out. Current moves in world trade (GATT) are leading to further reductions in subsidies and probably to an eventual elimination of quotas. In Germany, the fat content of milk is slightly above 4%. It varies depending on feeding. The same can be said about the fatty acid composition. In areas in which cows cannot be left outside to grass all year round but are stable-fed during winter, there is a great difference between summer butter and winter butter. Summer butter usually has a deeper yellow color than the pale winter butter; it is also softer. The difference in consistency is due mainly to feeding and corresponds to the degree of unsaturation of the fatty acids, reflected by the iodine value (Fig. 3.3). Summer butter is produced during the grassing period when fodder is more unsaturated in its fatty acids. Winter butter properties come from silage fodder. Recently one succeeded in changing the milk fat composition towards higher oleic acid content and less saturates, by feeding rapeseed for instance (Frede 1992). This difference is no longer obvious in many countries; summer butter is frozen and blended with winter butter or winter butter is colored with carotene. Both measures are taken to obtain butter with similar properties and appearance year round.
Animal Fats and Oils
125
TABLE 3.3 Cow Milk and Butter Production in the World and in Some Selected Countries (MMT)
Total world
us. Brazil India Germany France Netherlands Poland UK Italy
1960
1970
1980
1990
1993
1994
324 57.0 5.9 8.1 20.5 25.0 7.0 12.5 12.0 9.2
364 53.2 7.3 8.9 21.7 27.5 8.2 15.0 13.0 9.4
42 3 58.1 1 1.4 3.2 24.5 32.1 11.8 16.3 15.9 10.8
469 66.0 13.2 22.5 24.0 27.5 11.3 15.4 15.0 10.9
461 68.3 15.7 30.6 28.1 25.3 11.0 12.6 14.8 10.3
459 69.7 15.8 30.0 28.2 24.9 10.8 12.2 15.0 10.3
1990
1993
1994
Butter and Chee Production Expressed as Fat (MMT) 1960 1970 1980 Total world
U.S. USSR EU (10) India
4.4 0.5 0.8 1.1 0.5
4.9 0.4 0.8 1.3 0.5
5.7 0.4 1.1 1.7 0.6
6.2 0.5 1.3 1.5 0.9
6.0 0.5
6.0 0.5
1.1 0.9
1.1 1.o
-
Source: UNION 1979 and F A 0 Production Yearbooks
Fig. 3.3. Iodine value of milk fat depending on the season (after Precht 1988).
-
Fats and Oils Handbook
126
Butter fat is rich in palmitic and oleic acid (-25% each) and contains more shortchain fatty acids than most other fats. As with all ruminants, the t r m fatty acid (TFA) content is quite high. TFA are produced in the cow’s rumen during enzymic hardening. Naturally, fatty acid composition also depends on the breed, the feed and the area in which the cows are raised; thus a great variation in composition occurs (Fig. 3.4). 3.1.2 Milk Fat Production
As already mentioned, milk fat production is traditionally a branch of dairy technology because it has normally been produced from butter. Today, the following forms are differentiated: anhydrous milk fat, produced from fresh milk, cream or butter (fat content > 99.8%);anhydrous butter oil or anhydrous butter fat, produced from butter or cream (fat content > 99.8%);and butter oil or butter fat produced from butter or cream (fat content > 99.3%) (IDF Standards 1977). Although many industries such as the ice cream industry have been using butter for their products, the new trend is to use butter fat (anhydrous milk fat) because it is more homogeneous in terms of its processing properties. In some countries that allow reconstitution of butter, stockkeeping anhydrous milk fat is easier than storing butter. Further, processing of butter fat (for instance fractionation or hardening) is still restricted in some countries such as Germany; others are totally open in this respect. Traditionally, butter fat is obtained from butter. The membrane hulls around the fat globules of milk are destroyed by beating. Mechanical treatment induces agglomeration of the fat grains and phase inversion. Butter fat is then obtained by melting butter, separation of the fat phase, followed by clarification. Using the direct route
Fig. 3.4. Fatty acid composition of butter fat.
Animal Fats and Oils
127
from milk, cream is preconcentrated, the membrane hulls are destroyed and the fat directly separated by centrifugation of the highly concentrated cream (Fig. 3.7).
3.7.2.7Butter Oil (Butter Fat) Production from Butter. Butter oil production lines have an output of 1-10 ton/h (Fig. 3.6a). Usually deep frozen butter is used, which is warmed until it is pumpable. After complete melting in a plate heat exchanger (A) it is pumped into a buffer tank (B). If fresh butter is used, it is recommended to pass the butter through a vacuum chamber (C), thus easing the concentration steps that follow. The holding time in the buffer is necessary to ensure degassing of the molten butter. From the buffer, a self-discharging separator (D)splits the butter fat from the butter serum, concentrating the fat phase to 99.5%. The wet butter oil is heated again in a plate heat exchanger (E) to - W C ,and water is subsequently evaporated in a vacuum chamber @) to a maximum concentration of 0.1%. To recover heat, the butter oil is cooled countercurrently, passing (E) again. It is stored in (G). See also Figure 3.5. 3.7.2.2 Direct Milk Fat Production from Cream (Milk). A more or less novel process is to produce milk fat directly from full milk (Fig. 3.6b). To do so, cream which is obtained from milk by centrifugation passes a plate heat exchanger (H) and is heated to 55°C to inactivate lipolytic enzymes. It is fed into a self-cleaning centrifugal separator (J), which performs a preconcentration. The skim milk leaving the preconcentrator passes another separator (L) to recover residual fat. The skim milk leaves the plant countercurrently, heating the incoming cream as it is being cooled. In the late 1980s, the plant design contained a so-called clarifixator, a combination of preconcentrator and phase inverter. The latter was achieved using a toothed cavitation disc that breaks the emulsion by disintegrating the fat globules. This occurs when the cream concentrated in the first part of the clarifixator has reached a concentration of 75-80% fat. Today, this module of the processing Passing another line is no longer built. It has been replaced by a homogenizer (M). separator (N) and a plate heat exchanger (P),the butter oil is pumped via an evacuated vessel (0)into a storage tank (R). The part of the cream that was separated from the butter oil in (N) returns to the main stream to be partly reprocessed. This process is much less frequently used than milk fat production using butter as source material. One of the reasons is that butter from subsidized deep-frozen intervention stocks may be used.
3.1.3 Fact File of Butter Fat (Butter Oil, Milk Fat) Average (European) data for butter oil are given in Table 3.4 and Figure 3.9 and the triglyceride composition is given in Figure 3.8. See also Kermasha 1993).
3.2 Rendered Fats Bodies of cattle contain -5% fat, those of pigs -25%, whereas their carcass fat is 10 and 30%, respectively. Despite this relatively low percentage, the amount of
Fats and Oils Handbook
128
Full fa; milk
-
(3.5 4.3 %)
,
Cream
I
I
+
Cooling. @ing I l
c
>>> Skim Mik
Batch, 10-18'C, 2-10 h (without step N: 10-14%; 10 h) U
c
(if in step 111 t > 12% and ca.2h)
1
M'C, aeparaton. 2nd shge of Concentn(ion >>> Sweet crcam butter d u c t i o n >>> (sa8.1.5.5)
Skim milk
euitrr
usually rtomd d.ep frozen I
Holding for cwnpbh, making
Butter oil I
I
(99.5%)
I
Heating
to pumpability
to W C , pMe h u t exchanger; removal of water Water >>>
1 C
1
Cooiina
I
I
Butter oil
tO<WC
(> 99.9%)
Fig. 3.5. Flow chart of butter oil production from butter.
rendered fat produced per year is enormous as a result of the immense number of animals killed (Table 3.5). In the table, the difference between the number of slaughtered animals and quantity of animal stock is a consequence of the time required for the animals to reach the desired weight.
Animal Fats and Oils
129
Fig. 3.6. Plants for the production of butter oil from butter and from cream (redrawn courtesy of Tetra Lava1 Food AB, Lund). The determination of the amount of fat is not simple because a significant part is not processed separately but eaten with the meat without the consumer’s awareness (so-called hidden fat). Another substantial part is consumed in sausages, corned beef and other meat products. These hidden fats account for considerably more than half of the fats obtained from animal sources. The fat content of animals for slaughter has substantially decreased during the past 40 years. In the 1950s (in Europe) emphasis was placed on calorie intake, i.e., fat meat, whereas now the consumers ask for lean meat. In the 1950s in Germany, for example, the price for fat pork belly was 90% of that for lean pork chops; in the mid 1970s, it was 55%; and today it is <40%. The breeders, among others, followed this trend by breeding the 14-rib-pig and promoting lean races. As a result of such activities, the amount of fat per animal has drastically decreased. However, despite the decline of production in the former USSR, world lard production has
Fats and Oils Handbook
130
,+, Full fat milk
CIO'C
15
!c
vTfat)
!
Butt.rmilk
Conorntration Butter oil
(99.5% fat)
Fig. 3.7. Flow chart of direct butter oil production from milk. Butter oil
( > m.Q%Fat)
risen to about 5.5 MMT per year in the first half of the 1990s; the production of tallow and grease is just slightly <7 MMT. The carcasses of animals for slaughter vary in fat content depending on species, age, state and keeping (feeding) and sex (male, female, gelding). Although very lean meat is almost fat free (-1.5%), the fat content rises from medium fat (20%)to fat meat (30%) and reaches its maximum in adipose tissues (bacon fat, leaf fat), which can contain up to 95% fat (pig). Generally, the fat content rises from birth to killing but may have reached its maximum before killing (Fig. 3.10). As a matter of principle, female and gelded animals can be fattened more easily than males. Dahl(l973) reported that, under identical conditions, oxen accumulated 57% more adipose tissue than bulls. The kind of fat produced depended mainly on the genetic blueprint, i.e., its species. Feeding was found to influence the fatty acid composition but only to a limited degree. The same publication shows a proportionality between iodine value of the oils fed and the linoleic acid content of these pigs' lard. In general, one speaks about visceral (or
Animal Fats and Oils
131
Butter oil (fat) Tligly~xridrtype POP, MSO, SSLn, PSL POO, SOL LaSO, MPO, PSLn, PPL, MSL
MOO, SLL, SOLn LLL, OLLn CyOO, COL, LaLL, OLnLn LUn
LLnLn, CLL, CPLN, CyOL. CoCO
LnLnLn, CyLL, COOL. BuOO Proportion [mol%]
Fig. 3.8. Main triglyceride composition of butter oil (after Bornez 1992).
killing) fats from around the kidneys, the stomach, the intestine and the heart and about skeletal (or cutting) fats which are subcutaneous fats or fats from carcass butchery. During slaughtering, organs and cells are damaged so that their liquids are released. The enzymes present in these liquids can lead to lipolytic degradation. This is, of course, especially valid for lipases from the intestinal tract of the animals and consequently less critical for adipose tissues (skeletal or cutting fats) than for visceral or killing fats. The reaction rate of lipolysis increases with temperature but even at 4°C (-30°F) free fatty acids are formed quite rapidly (Figure 3.1 1). From the graph, it is clear that visceral fats are much more susceptible to hydrolysis. Consequently, fat production should take place as soon as possible after killing. 3.2.1 Fat Production
Fat can be produced batchwise with the use of manual techniques by melting the raw material in open vessels. It can also be done on a semi-industrial or industrial scale, semicontinuously or continuously. The quality of the source material depends mainly on the care taken during slaughtering. Overviews of different processing techniques are given by Dupjohann and Hemfort (1975) and Diipjohann (1989) who describe plants of Westfalia Separator AG (Figs. 3.12, 3.16, 3.18 and 3.19). A brief survey was presented by Hughes (1993).
Fats and Oils Handbook
132
TABLE 3.4 Fact File of Butter Oil (Milk Fat, Butter Fat) German: Milch-, Butterfett
French: graisse de beurre
Relative density Refractive index Saponification value Iodine value
(at 40°C; ref. water 20°C) (nD40) (mg KOH/goil) (Wijs method)
Spanish: grasa de mantequilla 0.9354.943 1.452-1.457 21 8-235 25-38 ~
Melting point:
28-38OC
Solids content at
("VF)
10/50
20/68
30/86
35/95
(YO)
43
18
5
0.5
World market price per MT
(average 1990)
~
1 5-25°C
Solidification point
3740 U.S. $
The draft Codex defines: Anhydrous milk fat, milk fat, anhydrous butter oil and butter oil are fatty products derived exclusively from milk and products obtained from milk by means of processes that result in almost total removal of water and nonfat solids. Ghee is a product obtained exclusively from milk, cream or butter by means of processes that result in almost total removal of water and nonfat solids, with an especially developed flavor and physical structure. Anhydrous milk fat or butter oil Milk fat, butter oil and ghee Minumum milk fat (% m/m) 99.8 99.6 Maximum water (% m/m) 0.1 Maximum free fatty acidsa 0.3 0.4 Maximum peroxide valueb 0.3 0.6
-
d m as oleic acid. bMilliequivalent of oxygenkg fat. a%
3.2.7.1 Slaughter. Slaughter was described in an overview by Troeger (1993). More detailed information was given by Prandl et al. (1988). It is essential for slaughter houses to strictly follow the rules of hygiene (for Europe issued as an EU directive, with certificates needed). This reduces the risk of microbiologic contamination from claws, coat or hide, sex organs, mouth, gullet, and the contents of stomach and intestine. The innards should be taken from the body in their entirety. It is very important to avoid major damage to the intestine and the lymphatic vessels so as to prevent quick degradation of the fats produced. For details on slaughter house hygiene, see the special literature, for example, Prhdl. 3.2.7.2 Batch and Semicontinuous Fat Production. The easiest (manual) way to extract animal fat batchwise is by finely grading the adipose tissue and melting it out in open vessels. Cracklings (greaves) and water collect in the lower part of the vessel and the fat swims on top. It is separated by decantation or by means of faucets built into the side wall. Mechanical disintegration helps to break up the structure and to ease fat release from the cells. Heating the fat-containing raw material also has the function of break-
Animal Fats and Oils
Fatty acid Butyric Caproic Caprylic Capric Lauric Myristic Palmitic Stearic C20+C22 Oleic Linokic C20 + C22
133
Proportion [K: C 410 C 6:O C 8:O C 10:0
c 12:o C 14:O C 16:O C 18:O sat. C 18:l C 18:2 unsat.
Trans fatty acids, total
2.8 1.4
0.8 2.0 2.2
-
-
3.8 2.8 1.7
3.0
- 3.5 5.5 - 13.5 24.5 - 36.5 6.5 - 13.0 1.5 19.5 - 32.5 1.2 - 3.3 3.5
e
2.0
-
7.5
Proportion [%
Fig. 3.9. Fact file of m i l k fat;
fatty acid composition.
ing up the cells and decreasing the fat’s viscosity. Depending on the type of fat, heating to 105°C decreases its viscosity to 15-20% of its value at 35°C (Sobstad 1990). Desirable side effects of heating are sterilization and enzyme deactivation; additionally, protein denaturation helps in breaking emulsions and separating the molten fat. This pattern of basic technological steps, namely, disintegration, heating and separation, can be found in all industrial rendering processes, however, in a further developed and more sophisticated form. Further development of this simple process includes melting in autoclaves in which heating is achieved by direct steam injection. Because the autoclaves are run batchwise, at best a semicontinuous process can be achieved when two or more autoclaves feed a press alternately. The process time in the autoclave is 4-6 h and the proTABLE 3.5 Stocks Slaughtered and M e a t Production in 1994 Number (million)
Cattlebeef Pigs/pork Sheep Goats Hens Turkeys
Stocks
Slaughtered
Meat production (MMT)
1288 a75 1,086 609 12,020 247
239 101 461 253
50.05 79.00 6.89 3.06
Source: F A 0 Production Yearbook 1994.
-
-
-
Fats and Oils Handbook
134
0
4
8
1 A-
2
*
a
2
4
t-ksl
Fig. 3.10. Composition of pigs, dressed weight (after Dahl 1973). cessing temperature is -150°C. An alternative is indirect heating of the autoclave. Using this process, the water of the fat-bearing material is evaporated and the fat is obtained at 110-1 15'C. The advantage of dry rendering is that considerably less effluent is created compared with wet rendering. Its disadvantage is that burning is possiFree fatty acids formed 2.0 I
[%I
I
I
0
1
2
3
4
5
6
7
8
9
storage at 4°C [days]
m
f
l
Fig. 3.11. Enzymic formation of free fatty acids during storage at 4°C (after Dahl 1973).
Animal Fats and Oils
135
Fig. 3.12. Semicontinuous dry rendering installation for processing animal raw tats (Westfalia Separator AC, Oelde).
ble, leading to poorer quality of the cracklings. Figure 3.13 gives the flow chart of the process that is schematicallyshown in Fig. 3.12. The fat bearing raw material (A) is fed to the processing line. After passing a metal detector (A), it enters a miner (B) for mechanical disintegration of the cells. After preheating in a melting tube (C), it enters the rendering tank @), i.e., the autoclave, which is described below. For continuous operation, several autoclaves have to feed one press. After switching off the vacuum pump, the content of the rendering tank is emptied via a sieve (E). There the cracklings are separated from the liquefied fat and the rekdual water. The retained cracklings are fed to a screw press 0. The fat is separated from the solids. Dripping fat from the sieves and fat obtained from the press are united and fed to a decanter (G) in which 8-2Wo of the solids are removed, these may be fed back to the press 0.After adding 1-2% of water and reheating, the fat obtained in the decanter is polished by a separator (H)and stored (J). If 10% of water is added to the fat before the decanter, a lighter colored oil is obtained (Dbpjohann and Hemfort 1975).
136
Fats and Oils Handbook
crud,kt
El
nt
Fig. 3.13. Flow chart of the dry rendering process.
All plants with a screw press should also have a metal detector to avoid damage to the press. There are different types of such equipment. The Krupp Maschinentechnik types consist of a screw conveyor (2.2 kW power supply) housed in a pipe containing a central plastic section. This section is equipped with a transmitter and a detection coil. The transmitter coil creates an electromagnetic field, which is received by the detection coil. If a metal piece passes this section, the field is distorted and an electrical current is induced in the detector. The signal created is amplified and operates a shutter that automatically opens to remove the metal particle from the stream of goods. Because this system also detects noniron metals, all metals can be separated. The capacity of dry rendering plants is limited by the throughput of the screw press (Fig. 3.14), which is fed by several autoclaves. In the screw press shown in Figure 3.14, the prepared fat-bearing material (A) is fed via the screw (1) into the press chamber (2)which holds the main worm shaft (3). The worm shaft is driven by an electrical motor (4) via a spur gear. The screw is housed in a horizontal cage (5) that allows the fat to separate (6) and retains the solids. The diameter of the screw rotating in this cage increases in the direction of the product flow to compensate for the volume loss due to the extracted fat and to increase pressure. The
Animal Fats and Oils
137
Fig. 3.14. Screw presses for the rendering industry (courtesy of Krupp Maschinentechnik GmbH, Hamburg).
138
Fats and Oils Handbook
fat flows through the slots of the cage, is conveyed out (7), and collected (B). The expeller cake (C, with 10% of residual fat) is broken (8) and conveyed for further processing. Depending on their size, common screw presses have a throughput of up to 4.5 M T h (Table 3.6). They are fed by the above-mentioned autoclaves shown in Figure 3.15. The prerendered meat pulp (P) enters the autoclave via (4). In this dry rendering process, the pulp is heated to sterilization temperature by contact with the inner walls of the double-jacketed vessel (3), which is steam heated (Sl). The electrically driven (2) double-walled shaft and the paddles of the stimr (1) are also heated by steam (S2). After sterilization, the content is pressed through a sieve disk (6) into the discharge opening (3,which is COM~C~XIto the stirrer shaft by the inner pressure. This causes further disintegration of the meadfat, making the following press extraction more effective. If sterilization is not necessary, a simpler layout can be chosen. A range of the size of such autoclaves is given in Table 3.7. To avoid the danger of spreading pathogens during processing and distribution of animal by-products, such offal has to be sterilized in pieces with a size not exceeding 50 mm, according to the European Union guideIine 90/667. To fulfill these prescriptions and to comply with the latest environmental legislation on emissions, which can hardly be met by the old autoclave generation, Krupp has replaced the above-mentioned autoclaves with a newly constructed continuous Helix sterilizer (Fig. 3.15). The Krupp Helix sterilizer is designed as a horizontal, cylindrical vessel rotating around its longitudinal axis with a charging chamber (B) on one end and a discharging chamber @) on the other end. The meat pulp (A) enters the chamber at a temperature between 133 and 14o'C. The atmosphere in the charging chamber (B), which is only half filled with meat pulp at s t e d h t i o n temperature, is kept at a minimum pressure of 3 bar. The headspace is saturated with water coming from the pulp. While passing the helix (C), which takes at least 20 min, the level of the pulp TABLE 3.6 Technical Data of Screw Presses for the Rendering Industry (Types EP; Krupp Maschinentechnik GmbH, Hamburg) EP-19
Input Output (cake) Residual fat in cake Required drive rating Size (excl. drive) (Lx D x H) Space required Length of screw Weight without drive Source: Krupp.
EP-07
EPb9
1 .0-1.9 2.0-2.8 3.1-6.2 0.6-1.2 1.3-1.8 2.0-4.0 10-12 10-12 10-12 90-1 10 110-132 30-45 3450x 1200x 1250 4550x 1360x 15OO 4550x 136Ox 1500
10 -1 900 5
15 -2550 10
15 -2550 105
Animal Fats and Oils
139
Fig. 3.15. Conventional autoclave sterilizer and novel Helix-sterilizer (courtesy of Krupp Maschinentechnik CmbH, Hamburg).
Fats and Oils Handbook
140
TABLE 3.7 Technical Data of Agitated Autoclaves (Type SSK, Suitable for Sterilization and Type E; Trademarks of Krupp Maschinentechnik CmbH, Hamburg) 12 (SSK) Cylinder data Length Diameter, inside Heating surfaced Autoclave data Length incl. drive Width Height Space required Weight Capacities Driving power Throughputb ~~~~~~~
~
Capacity incl. agitator (m3) 5.7 (E) 10.7(E)
14.7(E)
51
5000 1300 40
6000 1600 60
7000 1750 80
7440 2100 2712 10 25
7200 1500 4350-5850 10.8 13.7
8600 1800 4600-61 00 15.5 20.3
9750 2000 4800-6300 19.5 31.3
55 5-7
37 0.88-1.6
55 1.5-4.0
75 / 90 2.C-5.0
4700 1940
~~
Source: Krupp.
~lnclusiveagitator. bWithin an extraction line, depending on loading and unloading time, processing conditions and type of raw material.
remains constant. The headspace is completely water-saturated, thus ensuring sterilization. By the rotation of the windings, the meat pulp is continuously transported in partial quantities from the charging to the discharging chamber (D), which is equipped with a blade wheel. The sterilized meat pulp leaves at (F). This sterilizer can be used in any continuous plant design as shown in the following section.
3.2.7.3 Continuous Processes. Continuous plants consist of a sequence of machines for disintegrating and melting the raw material, separating the solids from the fat and the fat from the water. These machines are adjusted to each other by their throughput. Usually the wet rendering process is applied, i.e., heating by direct steam injection. Figure 3.16 shows such a plant, supported by its process flow chart (Fig. 3.17). The raw material (A) graded in the slaughter house is fed by conveyor screws (2) through a metal detector (3) into the mincer (4). Typically, the cutter consists of a rough cutter, precutter, double knife and a perforated plate with bores 4-8 mm in diameter. After prerendering in the melting tube (9,the disintegrated material enters the rendering tank (6), which is equipped with an agitator, steam regulator and deaerator. From the melting tank, the material is conveyed with an eccentric screw pump (7) to a decanter (8) where the residues (B) are separated from the liquid phase. This liquid consists of condensed steam, stickwater, liquefied fat and some residual solids. It is reheated in (9) and fed to a separator (1 1) by another eccentric screw pump (10). The solids (C) ejected from its self-cleaning bowl are fed back to the rendering tank (6).The fat leaving the separator is reheated and pumped to the second separation stage (12). For polishing, hot water may be
Animal Fats and Oils
141
Fig. 3.16. Wet rendering installation for processing animal raw fats with further degreasing of cracklings (redrawn courtesy of Westfalia Separator AG, Oelde).
added to improve separation. The polished fat obtained (D) is stored in (13). In case the residues are to be degreased further (residual fat content 4-8%), they (B) are conveyed into a storage tank where they are merged with the solids separated in (1 1) and (12). This mixture is reheated and passed through the clarifying decanter (14) and finally cleared via the separator (15). The fat emulsion (E) is then fed back into the rendering tank (9) and the solids (F) are added to the residues. The efficiency of the process can further be enhanced by introducing a separation decanter (8). As in the previous process (shown in Figure 3.16) the product is conveyed to the decanter by means of an eccentric screw pump (7) where the three phases
142
Fats and Oils Handbook
X
1
Fig. 3.17. Flow chart of animal fat production (lard, tallow, as in Fig. 3.16).
are continuously separated into fat, stickwater, and cracklings (B). The fat leaving the decanter is postheated in a tank (9) and fed to the separator (1 1) for fine clarification. Residual solids are removed (C) and the fat @) is stored in (15). Figures 3.19 and 3.21 show wet rendering plants (schematic and photograph), Figure 3.20 gives the respective flow diagram, and Table 3.8 liftsthe operational data. 3.2.7.4 Production of Bone Oil. Bone oil is extracted in plants equipped with an autoclave (Fig. 3.22). The bones are fed in at (l), broken in (2) and fed into a dry rendering autoclave (3, see also Figure 3.15, upper part) where they are thermally broken up and dried. Passing a prerendering unit with a built-in iron separator (4), the prepared raw material is fed into a screw press ( 6 ) after passing a buffer (5). The fat from (4) and (6) is combined and precldied in (7). A decanter (8) is used for the final separation of the fat (F)and the solids that were reprocessed in
Animal Fats and Oils 1.wO.O ko 750.0 kg
143
F W scum M M n l (100% Fat
75,O %
--n
Y
t
f
Fig. 3.18. Mass and energy balance of fat production, wet rendering process (after Dupjohann 1989/1996 and Westfalia Separator AG, Oelde).
(5). The press cake from (6) is ground (9) and conveyed to the meal storage (M). All vapors from the plant are condensed in (10) and the waste water (W) passes through an effluent treatment plant.
3.2.1.5 Solvent Extraction. This process is applied only for the extraction of animal fat for technical purposes (Fig. 3.23). The raw material is introduced via (1) and is conveyed into the stinwl autoclave after being disintegrated (2).In the autoclave (3), it is
144
Fats and Oils Handbook
Fig. 3.19. Wet rendering installation for processing animal raw fats using a separating decanter (redrawn courtesy of Westfalia Separator AG, Oelde).
sterilized and mixed with the solvent (usually perchloroethylene). The miscella (see also Chapter 5.2.4) is withdrawn through the bottom of the vessel, buffered in (4), and is recirculated for a second extraction step into the extractor (3). After the second use, the solvent is evaporated (5), and the crude fat is preclarified in (6)and pumped to the storage (F) after a fine clarification step in the decanter (7). Solid residues separated in (7) are fed back into the extractor (3). The solvent is evaporated from the solids, leaving the extractor (3) by direct steam (8). The bone/meat pulp is almost solvent free and comprises 4040% water. It is continuously dried in (9) and the dried meal is ground in a mill (10) and transported to the meal storage (M). The vapors, which contain some solvent, are condensed (1 l), and the water and solvent from the condensate are sepa-
Animal Fats and Oils
145
TABLE 3.8 Operational Data for a Wet Rendering Plant as Shown in Figure 3.1 9 (Courtesy of Westfalia Separator) Energy consumption
(kW/MT of raw fat) (kg/MT of raw fat)
Electrical energya Steam (3 barla Water consumption Hot water (t > 95%C) Cold water Operating water pressure YielddCapacities Capacity Fat yield
16-22 0.1-0.1 7
-250 -40 3
(MT of raw fat/h) (% fat content of raw material)
3 96-99
aDepending on type temperature on delivery of the raw material.
rated (12). The water is pumped to the effluent plant 0. All vapors from the plant that are difficult to condense are processed in a special treatment installation (L). In addition to the Krupp immersion plant described above (process flow chart in Figure 3.24), which is also available for continuous processing, plants for the percolation process are used (for example, De Smet extractors). In such plants, the raw material is broken up in a cooking step. The excess tallow is allowed to drip off onto a tray with a perforated bottom, thereby leaving a residue with typically 30-35% fat. This residue is coarsely ground so that the particle size (also bones) is reduced to <3 cm. Through a valve, the material is conveyed into the storage chamber of an extractor, which resembles those described in Chapter 5.2.3.4.3. The extracted material is separated from the solvent in a toaster; the solvent is evaporated from the miscella, conAdipose tissues
I
I
I
Sorting I
1 (5-6 rnrn diameter) 90-95'C, dired stearn
m Separation
Decanter
_ I
X
Fig. 3.20. Flow diagram of-fat production with rendering vessels.
146
Fats and Oils Handbook
Fig. 3.21. Wet rendering plant (Westfalia Separator AG, Oelde).
Animal Fats and Oils
147
Fig. 3.22. Plant for the press extraction of bone oil (Krupp Maschinentechnik GrnbH, Hamburg).
Fig. 3.23. Animal fat solvent extraction plant (Krupp Maschinentechnik GmbH, Hamburg).
Fats and Oils Handbook
148 Source material
I
1-L
Separation Mbmlla
I
hnter R
r Vapor mndrnution
t
I
Crude oil
~
Fig. 3.24. Flow diagram of solvent extraction (for technical use only).
densed and reused. There is no need for a miscella filtration because the material to be extracted acts like a filter cake and holds back all small particles. The loss of solvent (usually hexane) is <0.5%. 3.2.1.6 Combined Solvent Press Extraction. This process is similar to those described above. However, it combines solvent extraction and press extraction. The raw material is dried, first pressed and then solvent extracted. This lowers the amount of solvent that has to be removed, thus saving energy and reducing cost. In addition, plants exist that achieve the separation of miscella and extracted solid residue by pressing rather than decantation.
3.2.2 Lard The world population of pigs has increased considerably during the past five decades (Table 3.9). Currently, the world production of lard is -5 MMT per year. The dressed weight of pigs contains slightly above 30% fat (Fig. 3.25). Very fat pigs can contain more than 50% fatty matter, which is dispersed in the meat and concentrated in some fatty tissue, such as 6 5 % dressed weight (%dw) of bacon fat or leaf fat, 3%dw of cutting fat and 1% trimming fat. Lard is rich in palmitic and
Animal Fats and Oils
149
TABLE 3.9 Stock of Pigs and Lard Production in the World and in Selected Countries Stock of pigs Total world (M head) USSR
us. Brazil Germany FR Germany (former GDR) Sudan Mexico Poland Romania Vietnam Netherlands France Canada Japan Spain EU (10) Lard production Total world (MMT) USSR EU (1 0)
us. China PR
1935
1950
1960
1970
1980
1990
1994
50 32 22 12 -
20 59 25 10 -
530 58 56 53 15 7 9 13 5 9
567 56 61 66 20 9 7 10 14 6 6 11 7 6 7 65
779 74 57 34 23 12 18 19 20 11 9 10 11 11 10 10 78
857 79 53 33. 23 12
875 58 31 26
12 12 11 12 17 107
11 18 110
-
-
-
2 7 -
-
-
17 19 12
-
18 19 9 15 14 13 11
6 -
4 -
3 9 5 4 6 -
1935
1950
1960
1970
1980
1990
1994
2.9 -
3.0 -
4.4
4.4 0.6 0.7 0.8 0.5
4.0 0.7 1.0 0.5 0.8
5.4 0.8 1.2 0.4 1.6
5.7 1.2 1.2 0.4 2.0
2 7
-
-
-
0.5
0.5 0.9 0.4
Source: Schiittauf (1940), UNION (19791, and F A 0 Production Yearbook ( 1 994).
oleic acid (ratio 1:2), which account for three fourths of all lard fatty acids (Fig. 3.26). This has a strong influence on the triglyceride composition of lard. More than half of the triglycerides are composed of these two fatty acids, and 2-palmitodi-olein accounts for almost 20% (Fig. 3.27). Within limits, the composition of pig fat can easily be influenced by dietary intake.
Fig. 3.25. Composition of whole pigs and their dressed weight.
Fats and Oils Handbook
150
Fig. 3.26. Fatty composition of lard. Lard, which is partly modified via hardening and interesterification (Chapter 6.3 and 6.4), constitutes a good shortening for the baking industry and is used in the U.S.in large quantities. Because of traces of associated substances, it creates a nice crust and a special flavor in deep frying. It is therefore heavily used for baking
PPS, PSP
Pss. SPS
sss Wmr8
pop, Ppg MPO PSO. pos. SPO pm).
sos, sso oUvn MOO. OM0
oso. so0
wo OPO PPL SPL 0lh.n OOO PSO, SLO, SOL 0lh.n
sso
-
OOL. OLO PLL, SLL, W L n
WW
3.27. Triglyceride composition of lard (afterJurriens 1968).
Animal Fats and Oils
151
and deep frying despite the usually recommended restraint from animal fats. The definition for lard from the codex is as follows: “Lard is the fat rendered from fresh, clean and sound fatty tissues from swine (Sus scrofu) in good health, at the time of slaughter, and fit for human consumption as determined by a competent authority recognized in national legislation. The tissues do not include bones, detached skin, head skin, ears, nails, organs, windpipes, large blood vessels, scrap fat, skimmings, settlings, pressings, and the like, and are reasonably free from muscle tissue and blood. Rendered pork fat is the fat rendered from the tissue and bones of swine (Sus scrofu) in good health, at the time of slaughter, and fit for human consumption as judged by a competent authority recognized by national legislation. It may contain fat from bones (properly cleaned), from detached skin, from head skin, from ears, from tails and from other tissues fit for human consumption.” The values of the characteristic analytical parameters for lard and rendered pork fat differ only slightly from those given for lard in the fact file (Table 3.10 and Fig. 3.28). 3.2.3 Beef Tallow
The number of livestock cattle has increased by 50% over the past four decades (Table 3.11). The number slaughtered per year comprises 20% of the stocks; the world tallow production is currently -6 MMT. The proportion of fat in the dressed weight varies greatly (Fig. 3.29). Lean beef contains -8% fat, fat beef, up to 25%. On average, the proportion of visceral fat (or killing fat; from kidneys, stomach, intestine and heart) is -2% of the dressed weight of which -40% is kidney fat. TABLE 3.1 0 Fact File of Lard German: Schweineschmalz
French: saindoux
Relative density Refractive index Saponification value Iodine value Unsaponifiable matter
(at 40°C; ref. water 20°C)
Spanish: manteca 0.896-0.904 1.448-1.460 192-203 45-70 < 10
(mg KOH/g oil) (Wijs method) (g/kg oil)
Melting point:
2840°C
Solids content at
(VF)
10/50
20168
Solidification point 30/86
35/95
(Oh)
65
50
25
15
World market price
Price index (1995 average compared to average) 10 years ago 81 o/o 20 years ago 96O/o
(US$/MT)
2 2 -32°C
min
0
max
1972-1995
170
465
763
1982-1 979 1980-1989 1990-1995
170 332 229
481 533 325
763 710 500
Fats and Oils Handbook
152 Lard
C 14:l
C 17:O C 17:l
C 20:4
<
1.0
Trans hay .cidr.hW
Fig. 3.28. Fact file of lard; fatty acid composition.
Including skeletal fats (or cutting fats), -3% of the animal’s body is fat (half of the share in pigs). The definitions for different quality grades are as follows: “Premier Jus (Synonym: Oleo Stock) is the product obtained by rendering at low heat the fresh fat (killing fat) of heart, caul, kidney, and mesentery collectTABLE 3.1 1 Stock of Cattle and Tallow Production in the World and Some Selected Countries Stock of cattle
1935
1950
1960
1970
1980
1990
1994
Total world (M head) U.S. Brazil USSR Argentina France Germany UK EU (10)
-650
798 80 51 56 42 16 11 10
1013 104 79 83 43 20 13 12
1118 110 95 95 48 22 14 13
1264 99 134 121 51 21 16 12 84
1288 101 152
-
1220 112 117 115 56 24 15 13 85
Tallow production
1935
1950
1960
1970
1980
1990
1994
Total world (MMT)
1.7
2.2
4.2 2.3 co.1 0.2 0.1 0.5 co.1
5.0 2.8 0.1 0.3 0.2 0.6 <0.1
6.3 3.2 0.1 0.4 0.2 0.9 0.1
6.8 3.2 0.2 0.4 0.2 1.0 0.3
7.0 3.2 0.2 0.3 0.2 1.0 0.4
us.
Brazil USSR Argentina EU (1 0) China PR
66 60 33 16 12 9
-
-
-
Source: Schuttauf (1940), UNION (1979), and F A 0 Production Yearbook (1994).
-
50 20 16 12 80
Animal Fats and Oils
153
Fig. 3.29. Compositionof whole cattle and their dressed weight. ed at the time of slaughter of bovine animals (Bos tuunrs) in good health at the time of slaughter and fit for human consumption as determined by a competent authority recognized in national legislation. The raw material does not include cutting fats. Edible Tallow (Synonym: Dripping) is the product obtained by rendering the clean, sound, fatty tissues (including trimming and cutting fats), attendant muscles and bones of bovine animals (Bos taunts) and/or sheep (Ovis aries) in good health at the time of slaughter and fit for human consumption as determined by a competent authority recognized in national legislation.” The characteristic chemical and physical parameters do not differ substantially between premier jus and edible tallow. Apart from these two, bone oil and neat’s foot oil are also produced. Bone oil from fresh marrow bone can be used for edible purposes; other bone oil and neat’s foot oil are allowed only for technical use. Beef tallow contains mainly palmitic, stearic and oleic acid (Fig. 3.30). Neat’s foot oil serves as a high-grade lubricant for fine mechanical instruments. Its special properties are said to be due to the palmito-di-olein it contains. Tallow contains a wide spectrum of fatty acids and triglycerides. More than 50 different triglycerides in concentrations S . 1 % each have been identified. Unlike most other fats and oils, there is no predominant triglyceride with a high share. Only two, namely, palmito-oleo-stearin and palmito-di-olein, have a proportion >lo% (Fig. 3.31). The fact file reflects the characteristics as given in the Codex Alimentarius (Table 3.12 and Fig. 3.32). 3.2.4 Mutton Tallow
Mutton tallow is produced mainly in countries with large stocks of sheep and high consumption of mutton. Around 450 million sheep and lambs are slaughtered yearly, yielding >6 MMT of meat. Assuming -3% of fat (living weight), this corresponds to -0.5 MMT of total fat or -0.2 MMT of rendered fat. In some countries
Fats and Oils Handbook
154
Fig. 3.30. Fatty composition of beef tallow.
sss pss, SPS MSM, MSP. MSS, MPP PPP others PSO, POS
s o , sos PPO, POP MOP, PMO others, tnnsqlymrider PSL. PLS, SPL OPO POP
oso. so0 MOO, OM0 POSO, SPOO. SOP0 PPOO, POW, POOP others. tranr-gtycsrider
000 SLO, OSL, SOL PLO, POL, LPO POOO, OPOO others. trana-giycsrider 0 0 L , OLO others Proportion [mol%]
Fig. 3.31. Triglyceride composition of beef tallow (after Jurriens 1968).
Animal Fats and Oils
155
TABLE 3.1 2 Fact File of Edible Tallow German: Rindertalg
French: sulf comestible
Relative density Refractive index Saponification value Iodine value
(at 4OOC; ref. water 20°C) (nD40) (mg KOH/g oil) Wijs method)
Melting point:
0.893-0.904 1.448-1.460 190-202 32-50
Solidification point
40-50°C
Solids content at
Spanish: sebo
30-38OC
( O U T )
10/50
20/68
30186
35/95
(YO)
65
45
25
15
World market price Price index (1995 average compared to average) 124% 15 1Yo 248% 385%
10 years ago 12 years ago 30 years ago 35 years ago
(US$/MT)
min
0
max
1960-1995
123
326
655
1960-1969 1970-1979 1980-1989 1990-1995
123 162 242 310
160 362 420 337
218 643 621 650
(for example, Iran) fat-tail sheep, which store fat in a deposit'under the tail, are raised. This is used for fat production by hanging the tail in a warm environment and collecting the fat dripping out in a small bucket. The fatty acid spectrum of mutton tallow resembles that of beef tallow with the predominant fatty acids being palmitic, stearic and oleic acid (Fig. 3.33) The proportion of tram fatty acids is very high (-10%). The definition of mutton tallow is the same as that of beef tallow (see Chapter 3.2.3). Table 3.13 gives the fact file of mutton tallow.
Edible tallow (premi
-
Fatty acid shod chain Myrirlic Myriotobic Pentadscanic iso, anteis0 Pairnnk Palmilobic Maw& Margarolsic iso, anteiso stoaric
Obic Linoleic Linolenic
1
CC14 C 14:O C 14:l C 15:O C 15 C 16:O C 163 C 17:O C 173 C 17 c 18:O c 18:l c 18:2 C 163
Trans fatty acids. total
IW 'roporlion[%]
Bone grease
~
14 05 05
< 25 78 18 10 c 15
-
170 - 3 7 0 07 88 05 20 < 10 05 - 20 6 0 -400 260 -500 05 50 < 25
-
-
-4
'roporlbn [%]
Fig. 3.32. Fact file of edible tallow; fatty acid composition.
0.2
. 1.6
1
-
0.5
. 2.0
5
18 -32 2.5 9
-
3 -16 43 - 6 2 1.5- 3 1
Fats and Oils Handbook
156
Fig. 3.33. Fatty cornposition of mutton tallow.
3.2.5 Poultry Fat The number of poultry held world wide exceeds 10 billion. The fat that is obtained during killing is usually not processed separately. The fatty acid composition differs from species to species (Fig. 3.34). Except for goose fat, definitions can rarely be found. The German codex defines goose fat as follows: ''Goose fat is produced from the fatty tissue of geese and often for a better consistency is blended with declared propomons of lard." The fact file shows goose fat only (Table 3.14 and Fig. 3.35).
3.3 Marine Oils The term marine oils covers oils of all waterborne animals, fish or mammals, such as whales or seal. Hunting seal is of restricted regional importance only for TABLE 3.1 3 Fact File of Mutton Tallow German: Hammeltalg
French: suif de mouton
Relative density Refractive index Saponification value Iodine value
(at 40°C; ref. water 20°C) (nDa) (mg KOWg oil) Wijs method)
Spanish: sebo de corder0
0.893-0.904 1.448-1.460 190-202 32-50
~
Melting point:
45-50°C
Solidification point
Solids content at
("CpF)
10/50
20168
30186
35/95
(%)
60
37
20
12
30-38OC
Animal Fats and Oils
157
Fig. 3.34. Fatty composition of poultry fats.
Eskimos; consequently seal fat is not discussed here. A detailed description of the oils of almost all marine-born animals was given by Hilditch and Williams (1964); a survey of the present usage of marine oils is offered by Opstved et al. (1990). In the following paragraphs, the production of whale and fish oils is described. Whale oil is mainly of historical importance because only Iceland, Japan, and to a smaller extent, Norway, are countries still hunting whale. The amounts of oil, however, are negligible. Fish oil is a by-product of industrial fishing and the fish meal industry. Fish oil is therefore described in more detail. A debate is going on to restrict fish oil production to the amount that can be produced from sustainable fishing. In countries with a long shore line, such as Chile, for example, fish oil is of major importance. After slight hardening and fractionation, it can even be used as a salad oil. TABLE 3.14 Fact File of Goose Fat ~
~~
German: Ganseschmalz
French: graisse d'oic
Spanish: grasa de oca
Relative density Refractive index Saponification value Iodine value
(at 4OOC; ref. water 2OOC) (nD40) (mg KOH/g oil) (Wijs method)
0.902-0.906 1.456-1.462 191-1 98 59-81
Melting point:
25-37°C
Solidification w i n t
Solids content at
(VF)
10/50
20/68
30/86
35/95
(Oh)
35
18
5
1
16-22°C
Fats and Oils Handbook
158
Fatty acid Myristic Paimnic Palmnoleic
stearic Oleic Linoleic Linolenic Elcosenic
C 14:O
C 16:O C 163 c 18:O c 18:l
c 18:2 C 18:3
c -
.
18.0 25.0 1.0 - 5.0 5.0 8.0 50.0 -64.0 6.0 15.0 0.5 5.5
.
. -
20:1
Proporlion [%I
Fig. 3.35. Fact file of goose fat; fatty acid composition.
3.3.1 Whale Oil
International agreements have eliminated whale hunting almost completely, so that whale oil is no longer of significant importance. Some 40 years ago it was still important, and 60 years ago, margarine producers, for example, Walter Rau in Germany, had their own fleet of whale hunting boats. In 1957, an international conference agreed on quotas that allowed the hunting of 16,000 so-called “blue whale units,” which is equivalent to -0.3 MMT of whale oil. However, until the 1960s, 0.5 MMT of whale oil was landed yearly. For illustration, the composition of blue whales is shown in Figure 3.36. The liver of blue whales contains -2.5% of an oil rich in vitamins; it was used to produce vitamin A concentrates. Apart from the liver, the following portions of oil can be found in the subcutaneous fatty tissue, the meat and the bones: blubber, -50%; meat, -12%; and bones, -35% (up to 52%). This means that up to 25% of a blue whale, which can weigh up to 135 MT, consists of oil. The oil of arctic whales consists of 30% unsaturated C22and C24fatty acids; that of antarctic whales contains only -20%. This is reflected in the fatty acid composition as shown in Figure 3.37. The triglyceride composition was described by Hilditch (1939) who reported the following values for arctic whale oil:
Fig. 3.36. Composition of blue whale bodies.
Animal Fats and Oils
159
Fig. 3.37. Fatty composition of whale oils.
8 mol% 66 mol% 12 mol% 6 mol% 4 mol%
C,,:,-myristic acid-palmitic acid x {14, 16, 20, 22) 18:n-Cx: n-Cx: 0 C18:n-(Cx:n)2 x {14, 16, 20, 22) (Cx:nh-Cx:~ (Cx:n)3 x I14, 16, 20, 221
where CXZn is an unsaturated fatty acid with x carbon atoms and n double bonds and CxZ0 is a saturated fatty acid with x carbon atoms. Whale oil quickly becomes rancid, because of its high amount of polyunsaturated fatty acids and therefore was only used after hardening. Until the 1950s, it was an important ingredient of margarine. The head oil of the sperm whale, the so-called sperm oil, contains -50% of unsaponifiable matter. It is comprised of >50% waxes (fatty acid esters of longchain alcohols) of mainly cetyl alcohol. Sperm oil used to be the basis of liniments (see also Chapter 4.4.3). After hardening, products with unique and interesting properties could be obtained. Today, jojoba oil is used mainly as a replacement for sperm oil. Analytic and characteristic parameters of oils from different whale species can be found in Wissebach (1969) as well as Hilditch and Williams (1964).
3.3.1.7 Whale Oil Production. Modem whale hunting fleets fully processed the whale on the high seas. Each factory ship was accompanied by 8-15 hunting boats. A factory ship was able to process 1-2 whales per hour, depending on their size. Processing 25 whales per day (average weight 75 MT) yields 470 MT of oil. To obtain this weight in oil, 12,OOO-13,OOOpigs weighing 150 kg each would have to be killed.
160
Fats and Oils Handbook
To obtain the oil, the crude whale material is cooked and the oil is separated by decanters from the stickwater. The oil is clarified and collected, and the residues are further processed for glue manufacture (Fig. 3.38).
3.3.2 Fish Oil Fish oil is a by-product of the use of fishing as a source for protein or one of the two main products when whole fish is immediately processed for fish meal and fish oil production. The worldwide catch is -70 MMT per year. Populations of oil herring in the East Atlantic and of Menhaden in the West Atlantic have declined, leading to stagnation in the production of fish meat and fish oil. In addition, the anchovy catch on South America’s west coast has decreased considerably. This is due to the fact that the fish follow the Humboldt stream that passed the Peruvian coast until the 1960s. Recently, the stream has changed its direction and is now passing at a distance more than 350 km from the coast. In modem factory ships, by-catch and the residues from filleting fish are the source material for fish meal and fish oil production. The production of meal is about five times higher than that of fish oil. The dra-
sw S R
Whsk oil
---Ezka
VImln QwIQo(II(y <<<
Fig 3.38. Flow chart of whale oil production.
Animal Fats and Oils
161
matic decrease in Peru's fish oil production as a result of the above-described change of the behavior of the Humboldt stream is striking (Table 3.15). The processing of fish yields three groups of substances, water, fish oil and solids (mainly protein). Fish as a raw material contains only 25-35% dry matter; consequently, substantial amounts of water have to separated. On the high seas, its disposal does not create any difficulty at all; however, for shore-based plants, it may cause problems. The oil content varies from species to species. In typical fat fish, it can reach up to 21% (herring), 18% (sardines) and 16% (pilchard); the average oil content is -3-5% below these values. Fish oil is rich in polyunsaturated fatty acids, the proportion of which depends on the fish species and on where they are caught (Fig. 3.39). Fish oil is usually hardened before use because this modification improves the oil's keepability and reduces the tendency to become rancid. Rancidity is caused by the high degree of unsaturation, i.e., high number of double bonds per fatty acid molecule. Fish oil contains such a large number of fatty acids with equal numbers of carbon atoms but different number of double bonds that these fatty acids are usually not individually shown to characterize the oil. They are listed as CXIn with x being the number of carbon atoms in the chain and n being the average number of hydrogen atoms required to saturate the double bonds or, alternatively, with n indicating the average number of double bonds per fatty acid molecule (as in this book, Table 3.16). However, among the more than 60 different fatty acids identified so far, >80-85% are represented by four groups of fatty acids: C,,:, and C,,:,, Cl,:, and Cls:l, CZal and C22:1,and Cm5, C22:5, and c22:6 (Tucker 1993). In the majority of all triglycerides, the polyenic fatty acids are bound to the 2-position and the monoenic acids to positions 1 and 3. More than 90% of all polyunsaturated fatty acids in fish oils are of the 0-3 type (see also Chapter 1.4). The colder the water, the higher the amount of highly unsaturated fatty acids of the fish. The fact file in the left part of Figure 3.40 shows the average composition of fish oil as recorded in the German Codex. The large number of species TABLE 3.1 5 Production of Fish Oil in the World and Some Selected Countries
Total world (1000 MT) Japan Norway
us. Denmark Iceland Chile Peru USSR Germany Canada
1935
1950
1960
1970
1980
1990
1995
300
300
-
-
700 30 175 85 48 6 12 160 30 12 33
1400 87 180 93 51 7 23 31 1 60 14 27
1500 237 188 142 118 84 83 78 92 18 10
1500 490 115 140 85 105 190 120 95
1400 280 110 130 58 110 190 130 60
-
-
-
-
-
-
-
-
-
-
-
Source; Schuttauf ( 1 940),UNION (1 9791,and F A 0 Production Yearbook (1995).
-
-
Fats and Oils Handbook
162
Fig. 3.39. Fatty composition of fish body oils.
and the great influence of their environmental conditions, however, make it necessary to appreciate that a wide variation is possible. This is reflected in some extreme cases that are also given in that figure. It must be mentioned that Tucker stated that fish oil analysis is not very representative because it is based largely on single sampling, which does not take into account the environmental effects, the age and the differences between species and subspecies.
3.3.2.1 Fish Oil Production. Figure 3.41 gives a simplified flow chart of fish oil production. The most important facet of fish processing is efficient separation of its three main components, dry substance (protein), oil and water. For good quality, it is essential to keep the contact time to a minimum. Traditional plants use screw presses to separate the liquid (oiywater) from the solid phase. The raw fish material is prepared by an initial cooking step to coagulate the protein and to open up the fat-containing cells. This processing step is essential for the quality of the products and also pasteurizes the fish and inactivates enzymes. Usually, horizontal cookers are used through TABLE 3.1 6
Average Number (n) of Double Bonds per Fatty Acid Molecule in Fish Oils
Herring Pilchard Sardines Menhaden Salmon
-1.0
-1.0
-
1.2-1.7 -1.0 -1.0 1.5-1.7 -1.0
1.5-2.2 1.5-1.7 1.5-1.9 1.6-2.0 2.6-2.8
2.2-3.5 2.0-2.2 2.2-2.6 4.0-5.0 4.2-4.7
3.8-5.5 4.0-4.5 2.3-2.7 3.84.0 6.4-6.8
1.8-2.0 4.3-5.5
-
-
125-160 16G190 160-1 90 155-1 95 140-1 65
Animal Fats and Oils
163
Fish oil Proportion [%I
Falty acid
C 14:O
Myristic Palmitic Paimitoleic Stearic Oleic Linoleic Linolenic Eicosenic Tirnnodonic Cetoleic, (+ erucic) Docosapntaenoic Clupanodonic
C 16:O C 16:l c 18:O c 18:l c 18:2 C 18:3 c 20:l C20:5 C22:l C 22:5 C 2216
0-3 0-11
0-3 0-3
Proportion [%]
Fig. 3.40. Fatty file of fish oil; fatty acid composition.
which the mashed fish is conveyed by screws (Fig. 3.43). The cookers are heated by steam via a jacket. In the event that the raw material is difficult to open up, steam may also be injected directly. The cooker in turn feeds a screw press, which separates liquids and solids. The expelled solids (Graxen with 32-35% dry matter) are milled and fed to a drier; the liquids from the press, the press water, is pumped into a buffer vessel where it is heated with direct steam. A decanter is fed from the buffer, which removes residual solids that are combined with those from the screw press and are jointly TABLE 3.1 7 Fact File of Fish Oil ~
German: Fischol
French: huile de Poisson
Spanish: aceite de pescado
Relative density Refractive index Saponification value Iodine value Unsaponifiable matter
(at 40°C; ref. water 2OOC) (nD40) (rng KOH/g oil) (Wijs method) (gkg oil)
0.900-0.922 1.467-1.475 179-1 98 105-1 90 <1 5
Melting point:
<
Solids content at
("CPF)
0132
10150
20168
30186
35/96
(%)
0
0
0
0
0
Solidification point
(US$/MT)
<
rnin
0
rnax
Price index (1995 average compared to average)
1962-1 995
76
300
592
10 years ago 20 years ago 30 years ago 35 years ago
1960-1 969 1970-1979 1980-1989 1990-1995
76 147 133 200
156 364 326 342
237 592 488 525
153% 134% 2 1 1Yo 455%
'
Fats and Oils Handbook
164
Whole fish
&
Fish oil
Fig. 3.41. Simplified flow chart of the whole-fish process.
processed further. The press water is heated in a second buffer vessel by direct steam injection and is fed to a separator,passing a rotary brush strainer. The strainer (Fig. 3.42) guarantees that fibrous residues that have passed the decanter are separated, thus preventing blockages in the feed, disc stack and nozzles. The suspension is fed into the strainer via an inlet (1) where the solids collect on the inside of a cylindrical, perforated strainer insert (2) and are pushed down into the conical sediment holding space (3) by rotating brushes (4). The solids are discharged periodically through the solids outlet (6). A tangentially arranged flushing connection ( 5 ) serves as cleaning device for the strainer. Application of a strainer in the plant is optional; however, it increases the standing time. After reheating and the addition of hot water, the press water is fed into a selfcleaning separator for deoiling, and the separated water is pumped to the evapora-
Fig. 3.42. Rotary brush strainer (courtesy of Westfalia Separator AG, Oelde).
Animal Fats and Oils
165
Fig. 3.43. Conventional fish oil production process (redrawn courtesy of Westfalia Separator AG, Oelde).
tion plant. The turbid oil is heated again and passes a second separator for polishing, i.e., removal of residual water. Modern decanters for preclarification of the press water achieve throughputs of up to 70,000Lh;the residence time is on the order of some seconds only. For the deoiling of press water, self-cleaning separators can process up to 80,000 LJh (Westfalia 1996). The clean oil that leaves the processing line contains -0.1% water, whereas the fat content of the stickwater varies between 0.1 and 0.6% depending on the conditions of the raw material and the thermal treatment. The size of the decanters for press water clarification is determined by the location of the plant. Shore-based plants with a capacity up to 60,OOOLm are pos-
166
Fats
and Oils Handbook
Cooker, breaking up calls. pasteuruing
1
Steam injection
Press water (liquor) I
90-95'C. Steam injection Rotary brush strainer. removing coarse and fibrous solids Separator
i
I
n
-
1
Direct steam
I
Concantrate
<<< Hot water, 9O'C
t
t
>>> EMuent (max 0 6% fatty matter)
Fig. 3.44. Flow chart of fish oil production (as in Fig. 3.43). sible, allowing the processing of press water with up to 25% dry matter. On the high seas, plants on ships achieve only 25% of this throughput. The largest twostage separators have a throughput of 80,000 L h , one-stage separators only 60% of that. On the high seas, throughputs of -10% of these values can be realized.
Animal fats and Oils
167
Fig. 3.45. Fish oil production with the whole-fish process (redrawn courtesy of Westfalia Separator AC, Oelde).
In the so-called full fish process (Fig. 3.45), the plant configuration is changed. After the cooker, the fish passes a decanter, which separates the solids from the liquid phase before the screw press. The liquid from the press is fed back into the product stream before the decanter and passes through it again. The clarified press water is pumped through a rotary brush strainer and is reheated and separated by a separator (Fig. 3.46). The turbid oil and the solids are processed further as illustrated in Figure 3.43. Modern plants are equipped with three phase decanters instead of the layout described above, thus using less equipment. The decanter and the two separators in Figure 3.44 are replaced by one decanter that separates the solids from the liquid and also splits the liquid into an oil and a water phase. This process is limited to solid contents <40% voVvol and to raw materials with oil contents of <15%. The separation sharpness is less well defined than with the previously described processing equipment. Oil contents <0.8% in the stickwater and water contents <0.5% in the oil have to be accepted. The graxen have a humidity of 65-68%, which is equivalent to what can be achieved in the traditional process. With three phase decanters, throughputs of 1.8 M T h in the conventional process and 1.5 MT/h in the full fish process can be achieved. Special processes that achieve very high yields have been developed for lodde (Figs. 3.47 and 3.48). Figure 3.49 shows a fish oil production plant with a selfdischarging separator (Westfalia Separator AG) in the foreground. 3.3.2.2 Breaking Cells Up with Voltage Pulses. After disintegration of the fish, the cells are broken up to improve the oil release. In the traditional process, this is
168
Fats and Oils Handbook
Fig. 3.46. Flow chart of the whole fish process.
--
b
avr
Fig 3.47. Installation for fish meal and fish oil production with three phase decanters (redrawn courtesy of Westfalia Separator AG, Oelde).
169
Animal Fats and Oils
Fish
I
Cooker (A), breaking up calls, pasteurizing
R =Residue SW =Stickwater
I
W W C , steam injection (C)
Heating
Three phase decanters (D)
SW Stickwater <<<
Oil
R
Ij Fish meal
Clean fish oil
Fig. 3.48. Flow chart of fish oil production with three phase decanters.
done mechanically; the cells are cracked by mechanical stress or during heat treatment by thermal expansion of the liquids in the cell. Thermal disintegration inevitably denatures the protein. To avoid protein degradation by high temperatures and to make proteins accessible for further com-
Fig. 3.49. Installation for fish liver oil production (courtesy of Westfalia Separator AG, Oelde).
Fats and Qils Handbook
170
Fig. 3.50. Plant for fish liver oil production (redrawn courtesy of Westfalia Separator AC, Oelde).
mercial use, the Elcrack process was developed by Krupp (no longer available). For this process, cell walls are perforated by low-frequency high-voltage electrical pulses; above a particular field strength, this leads to a perforation of the cell walls. The field strength that has to be applied is inversely proportional to the size of the cells. In fish, muscle (250 pm) and fat cells (150-250 pm) are relatively large; consequently, only low field strengths are required for perforation. In this process, proteins already coagulate at 30°C and can thus be treated gently. Because this process is not applied, no further details are given here. 3.3.3 Fish Liver Oil Fish liver oils are especially rich in vitamins A and D and are therefore high-grade carriers of vitamins. Decanters can separate up to 6 MTh of mashed fish liver. Four rotary brush strainers are needed in the line to keep pace with the decanter. Separators ashore can be fed with up to 5 MTh of mashed liver; on the high seas TABLE 3.1 8 Average Number (n) of Double Bonds per Fatty Acid Molecule in Fish Liver Oils Liver oil
Cod Tuna Halibut Haddock
cl6:n
CI 8:n
C20"
C22:n
Iodine value
1.o-1.2 1.2-1.3 -1 .o -1 .o
1A 1 . 5 1.4-1.5 -1 .o 1.2-1.4
-3.0 2.5-2.8 2.6-2.8 2.8-3.1
3.3-3.5 3.4-3.7 3.5-3.8 3.3-3.7
150-1 75 155-1 80 15C-170 170-1 90
Animal Fats and Oils
171
Raw fish liver I Conveying, dblntegration (A) Buffer tanka Coagulation (B)
J.
Clean liver oil
Fig. 3.51. Flow chart of fish liver oil production (as in Fig. 3.50).
Fig. 3.52. Fatty acid composition of fish liver oils.
172
Fats and Oils Handbook
aboard a ship 1.5, M T h is the maximum. The yield of the process shown in Figure 3.50 is 95-96%; the flow chart in Figure 3.51 explains the process. In addition to the large amount of vitamins, fish liver oil is also rich in polyunsaturated fatty acids (Fig. 3.52). The fatty acids are distinguished only by their chain length, not by the number of double bonds. Table 3.16 shows the average number of double bonds for the acids shown in Figure 3.52.
3.4 References Alais, C., (1981) Science du lait, Principes des Techniques Laitieres, SEP-Verlag, Paris. Tetra Laval, uAlfa-Laval, Technical Information: Anhydrous milk fat, a product with wide industrial potential/Butterol-HerstellungNerfahren zur Herstellung wasserfreien Milchfettes,Turnba, Schweden. Anonymous, (1984) Bundesanzeiger, Der Bundesminister der Justiz, Bekanntmachung von weiteren Leitsatzen des deutschen Lebensmittelbuches,26 Mai, 1984. Bornaz, S . , Novak, G., Parmentier, M., (1992) Seasonal and Regional Variation in Triglyceride Composition of French Butterfat, J. Am. Oil Chem. SOC. 69, 1131-1 135. Dahl, O., (1973) Schlachtfette, Fleischforschung und Praxis, Heft 10, Verlag der Rheinhessischen DruckerwerkstiWe,Alzey . Dupjohann, J., and Hemforth, H., (1975) Verfahren zur Verarbeitung von tierischen Rohfetten unter besonderer Beriicksichtigung zenhfugaler Kliir- und Trennvorg2inge, Sonderdmck aus Fette, Seifen Anstrichmittel,Heft 3. Dupjohann, J., and Hemforth, H., (1989) Separatoren, Decanter und Prozeblinien fur die Gewinnung von Speisefett, Broschiire der Westfalia Separator AG, Oelde. Frede, E., Precht, D., Pabst, K., and Philipzcyk, D., (1992) h e r den Einfluss der Menge und technischen Behandlung von Rapssaat im Futter der Kuh auf die Htirteeigenschaften des Milchfetts,Milchwissenschft 8,47. Geigy, Documenta Geigy, edited by von K. Diem and C. Lentner, J.R. Geigy, S.A., Basel, 1968. Hilditch, T.P., and M u d , H.S.(1939) The fat of land crabs (Seychelles Islands), J. Chem. SOC. I d . 58,351-353. Hilditch, T.P., and Williams, P.N., (1964) The Chemical Constitution of Natural Fats, Chapman & Hall, London. Hughes, D., (1993) Production of Animal Fats, in Encyclopaedia of Food Science, Food Technology and Nutrition, Academic Press, London. ISTA Mielke, (1994) Oil World 2012, ISTA Mielke, Hamburg. Kennasha, S . , Kubow, S . , Safari, M., and Reid, A., (1993) Determination of the Positional Distribution of Fatty Acids in Butterfat Triacylglycerols, J. Am Oil C h m SOC. 70, 169-173. Kiermeier, F., and Lechner, E., (1973) Milch und Milcherzeugnisse, Paul Parey Verlag, Berlin. Krupp, Krupp Industrietechnik GmbH, Hamburg, Technische Information: Verwertung sanlagen fur tierische Abfdle/Schneckenpressen Typ EP/ Riihnverksautoklav Typ SSW Fischverarbeitungnach dem Elcrack-Prozess. Opstevdt, J., Urdahl, N., and Pettersen, J., (1990) Fish Oil-An Old Fat Source with New Possibilities, in World Conference Proceedings, Edible Fats and Oils Processing: Basic Principles and Modem Practices, (Erickson, D.R., ed.), pp. 250-259, American Oil Chemists’ Society, Champaign IL.
Animal Fats and Oils
173
Mdl,O., Fischer, A., Schmidhofer, T., and Sinell, H.-J., (1988) Handbuch der Lebensmitteltechdogie: Fleisch, Technologie und Hygiene der Gewinnung und Verarbeitung, Verlag Eugen Ulmer, Stuttgart. Precht, D., (1988) Qualitatseinstufung und schnelle Jodzahlbestimmung von Butterfett anhand der Triglyceridanalyse, Z. Lebensmitteluntersuch. Forsch. 187,457-482. Schuttauf, W., and Pischel, U., (1978) Die Margarine in Deutschland in der Welt, Presseabteilung der Union Deutsche Lebensmittelwerke, Hamburg. Sobstad, G., (1990) The Effect of Process Technology on Fat Quality, in World Conference Proceedings, Edible Fats and Oils Processing: Basic Principles and Modem Practices, (Erickson, D.R., ed.), pp. 31-36, American Oil Chemists’ Society, Champaign, IL. Sobstad, G., (1990) The Technology of Separation and Purification of Marine Oils, in World Conference Proceedings, Edible Fats and Oils Processing: Basic Principles and Modem Practices, (Erickson, D.R., ed.), pp, 3 7 4 2 , American Oil Chemists’ Society, Champaign, IL. Smet, Extraction de Smet S.A., Edegem, Technical Information: Extraction of Animal Products . Topel, A., (1976) Chemie und Physik der Milch, VEB Fachbuchverlag, Leipzig. Troeger, K., (1993) Slaughter, in Encyclopaedia of Food Science, Food Technology and Nutrition, Academic Press, London. Tucker, B.W., and Pigott, G.M., (1993) Fish Oils, Composition and Properties, in Encyclopaedia of Food Science, Food Technology and Nutrition, p. 1896, Academic Press, London. UNION, 50 Jahre UNION, Werkszeitschrift der UNION Deutsche Lebensmittelwerke, Hamburg, (1979). Veisseyre R., (1975) Technologie du h i t , Verlag La Maison Rustique, Paris. Walstra, P., and Jeuness, R., (1984) Dairy Chemistry and Physics, John Wiley & Sons, New York. Westfalia, 1985 and 1996, Technical Information: Separatoren, Decanter und Prozesslinien fiir die industrielle Fischverarbeitung/Separatoren und Decanter in der Fischindustrie, Technische Information, Westfalia Separator AG, Oelde. Wong, N.P., (ed.), (1988) Fundamentals of Dairy Chemistry, Van Nostrand Reinhold Co., New York.
3.4.1 References for Fatty Acid Composition I
Hilditch, T.P., and Williams, P.N., (1964) The Chemical Constitution of Natural Fats, Chapman and Hall, London. Rudischer, S., (1959) Fachbuch der Margarineindustrie,Fachbuchverlag, Leipzig. Ill IV Wissebach, H., (1969) Pflanzen und Tierfette (ausgenonunen Milchfette). Vorkommen, Gewinnung, Zusammensetzung, Eigenschaften Verwendung; in Handbuch der LebensmittelchemieIV,Springer Verlag, Berlin. XXI Sonntag, N.O.V., (1979) Structure and Composition of Fats and Oils, in Bailey’s Industrial Oil und Fat Products, (Swem, ed.),Interscience Publishers, New York. XXII Baltes, J., (1975) Gewinnung und Verarbeitung von Nahrungsfetfen, Verlag Paul Parey, Berlin.
Chapter 4
Vegetable Fats and Oils
Almost all plants contain fats or oils, mainly in their seeds. The amount varies from very little to as much as 7 0 4 0 % (Table 4.1). For a plant to be suitable for oil production on the scale required today, it must meet the following two criteria: (i) The oil or fat content must reach the minimum for commercially viable exploitation. (ii) The plant must be suitable for high acreage cultivation. The only exceptions are plants that contain oils or fats unique in their composition or with properties that cannot be found elsewhere. The number of oil-bearing plant varieties is quite high. However, only a limited number are exploited and traded worldwide; many are of regional importance only or serve very special purposes. These will be mentioned only briefly. In principle, there are two groups of fats and oils, denominated after their source, namely, pulp oils and seed oils. Within these two groups, further categorization is possible, usually based on the fatty acid composition, on the state of aggregation or on the species or group of species in which the oils occur (Table 4.2). In this chapter, the most important source materials are covered in some detail, giving their history, economic importance, composition and usage. Furthermore. their yearly production and yields are shown. The data are from Schuttauf (1978) and the F A 0 Production Yearbook unless otherwise stated; the references are therefore not repeated in the individual tables. The figures given for the year 1935 are actually averages of 1934-1938, and the data for the year 1950 do not include the Soviet Union. Some 1970 data are from 1969, and the 1935 data for India and Pakistan are summarized under India. TABLE 4.1
Fat Content of Food Edible part of
Fab'oil
Potatoes Lentils, dried Mushrooms, dried Oat flakes Wheat germ Soybeans Coconuts Peanuts, roasted Almonds Walnuts Pecan nuts
(-O/O)
0.1 1 3 6.5 11 20 34 44 54
64 71
174
175
Vegetable Fats and Oils
TABLE 4.2 Classification of Oils and Fats Pulp oils: palm oil, olive oil, avocado oil Lauric oils: coconut oil, palm kernel oil, babassu oil, laurel oil, nutmeg oil, dika butter Fats rich in palmitic and stearic acid: cocoa butter, illip6 butter, mowrah butter, shea butter, borneo tallow Seed oils rich in palmitic acid: cottonseed oil, cereal germ oils, corn oil, pumpkin oil Seed oils rich in oleic and linoleic acid: sesame oil, sunflower oil, safflower oil, niger oil, linseed oil, poppy-seed oil, grape-seed oil, walnut oil, fruit-seed oils, berry-seed oils, tea-seed oil Oils of Legurninosae: peanut oil, soybean oil, lupine oil Oils of Cruciferae: rapeseed oil, mustard-seed oil
All information given on the composition of the oil fruit and oilseeds is typical, but not definitive, because of variations resulting from the many subspecies, the progress in plant breeding, the climate, and the location of the fields. The fatty acid composition includes data that were published by three different authors. The light bars show the minimum content mentioned in the respective publication; the dark bars reflect their maximum. This may include rare varieties; consequently, the figures may differ considerably from the averages. The Roman numerals in these fatty acid composition graphs indicate the reference and are explained in Chapter 4.6.2.0. The triglyceride composition of the main oils is also given, using the following abbreviations: C La S L
= capricacid
= lauric acid = stearic acid = linoleic acid
Ca M A Le
= = = =
caprinic acid myristic acid arachic acid linolenic acid
P = palmitic acid 0 = oleic acid Er = erucic acid
Production flow charts illustrate how to extract the main oils and fats; following these there are fact files, with the most important data compiled for the individual oil or fat. Unlike the fatty acid composition graphs mentioned above, these figures are from the Codex Alimenturius or governmental publication and exclusively represent seed varieties that are commonly traded. For different periods of time, average prices, as well as minimum and maximum prices, and price indices are given in the Codex. For those oils that are not commonly traded, the price of April 1990 is given; with these figures, one has to bear in mind that 1990 was a year with a relatively low price level in relation to the historical averages. A more detailed review of oil-bearing plants with a description of subspecies, information on different stages of plant development as well as requirements in
176
Fats and Oils Handbook
terms of soil and climate, sensitivity towards pests and diseases, and information on harvesting in different regions is given by Weiss (1983). Godin and Spensley (197 1) collected information on tropical plants. Lennerts (1984) describes the origin of oil plants as well as their utilization and that of their extraction meal. A detailed description of the preparation for extraction can be found in Bernardini (1985). Salunkhe and Desai (1986) discuss the parameters that influence the seeds after harvesting. More general references are given in Chapter 4.6.0.
4.0 Summary New methods of plant breeding enable the cultivation of oil plants with desired properties at an ever increasing rate. The yield depends on the species, but can be improved by appropriate dates of sowing and harvest, irrigation, fertilization, and the right plant density. Most oil plants originate from large-scale agriculture or plantations. Pulp oils are processed close to the plantations because the harvested fruit quickly spoils and cannot be easily transported. Seeds from oils plants are more suitable for transport. In fact, they are better transported than extracted oil, because the oil is protected in the seed. To maintain quality, they must be dried to an adequate moisture that differs from seed to seed. Ventilation and possibly also cooling are necessary for long storage. Because of the different mechanical stability of the different seeds, certain heights of the storage silos must not be exceeded. Origin, yield and fatty acid composition, as well as usability of the meal, differ from seed to seed. These factors determine its price.
4.1. Oil/Fat-Containing Plants With -39 kJ/g (-9 kcal/g), fat has an extremely high caloric value, more than double that of carbohydrates. It is therefore best suited to store energy reserves; metabolic processes involved allow this energy to be released quickly. Plants therefore use oils in their metabolism as well as for energy storage. The high caloric value is related to the high proportion of carbon atoms (7675% of the molecular weight). It has been shown that plants initially store surplus energy as carbohydrates. During seed ripening, these carbohydrates are transformed into triglycerides. This happens according to an individual time pattern for each species and with individual intensity. Trials have been conducted with radioactive-marked linflowers, and they showed that fat is built from the 25th day on. In cotton, this process begins later, but with much higher intensity. As an example for seed oil plants, an investigation of Harris et al. (1978) can be cited; they traced the formation of fatty acids during the ripening of sunflower seed (Fig. 4.1). George and Arumughan (1993) did the same for palm oil. Anthesis of sunflowers is -90 d after sowing, and it can clearly be seen from the figure that each of the four main fatty acids then passes a maximum proportion. This starts with C16:O and shifts to C18:2, which constitutes the highest proportion (-75%) in
177
Vegetable Fats and Oils
Proportion of fatty acid [%]
Proportionof fatty acid [%I
Days after anthesis
Days after anthesis
Fig. 4.1. Fatty acid distribution in developing sunflowerseed and palm fruit (after Harris et al. 1978 and George and Arumughan 1993).
the ripened seed. In other fruit, this development can be completely the opposite. Padua-Ressurection and Bannon (1979) found that unripe coconuts contain -30% oleic acid and 20% linoleic acid -8 mo after anthesis. This proportion decreases to <5%, respectively, to 1% during ripening; the amount of lauric acid compensates for it, rising from 16% to almost 50%. In the ripened seed, the fat offers the plant a maximum of energy content with a minimum of space required because of its high caloric value. During germination, this fat is reconverted into carbohydrates, thus setting free the energy. To start the reaction, H20
carbohydrate
t)fat
high amounts of water are necessary, which is the main influence on the reaction equilibrium. The low water content of the ripening seed shifts the equilibrium in the direction of fat, and the much higher water content of the germinating seed in the direction of sugars. One gram of fat is converted into 2.7 g of carbohydrates. Using this reaction, the plants manage to set free the complete energy stored in the seed within 12 h. The synthesis of fat in the plant is started by the individual synthesis of its two components, glycerol and fatty acids. Glycerol is formed with the help of adenosintriphosphate from the dihydroxiacetonphosphate of the carbohydrate cycle (Diivel). The synthesis of fatty acids has been researched with radioactive marking. Carbon dioxide is attached to acetyl-coenzyme-A with the aid of a biotin CO, complex yielding malonyl-coenzyme-A. After that, another acetyl residue is attached, which via keto acids (splitting off C02) leads to fatty acids. Fatty acid
178
Fats and Oils Handbook
coenzyme-A complexes are attached to the glycerol phosphate, from which the triglyceride is formed via several intermediates. In palm fruit until wk 12, the oil makes up for 0.05% of the fresh mesocarp; in wk 16 it has reached 9%, 35% in wk 20, and 44%in wk 24 (George and Arumughan 1993). The oil is stabilized in the seed by a novel class of proteins, the so-called oleosins. These serve as stabilizers of oil-body emulsions especially during seed dehydration and may play a role in facilitating the mobilization of storage oil after seed germination (Murphy 1993). The majority of plants that are used for oil production contain the oil in their seeds. The traditional oil plants are grown in the earth‘s sun belt because high energy, which can be obtained only from sunlight, is needed for the synthesis of fats. Only in recent times have plants from moderate climates been used in larger amounts. To do so, efforts had to be made in plant cultivation, a development that can be characterized as stormy. Figure 1.6 show the production trends of moderate climate plants such as soybeans, sunflower and rape and that of tropical plants such as coconuts and palm fruit. 4.1.1. The Composition of Oil Fruit and Oilseeds
Oils and fats of the main oilseeds are equal in that they have similar fatty acid composition. This is restricted mainly to five fatty acids, namely, myristic, palmitic, stearic, oleic, and linoleic acid, with some allowance for linolenic acid. Often oil fruit and oilseeds contain by-products that have to be separated, for example, lecithin in the case of soybeans. These by-products are used in other ways. The presence of some unwanted by-products (lipids), such as gossypol in cottonseed or erucic acid in traditional rapeseed, caused heavy restrictions to be imposed on the usage of the extraction meal and the oil. Here, the cultivators were and are challenged to grow better varieties. Breeding new varieties can lead to either radical changes, e.g., in the fatty acid spectrum or to minor improvements such as less sensitivity toward climate changes, higher resistance against pests and disease or higher yields. Rapeseed (see Chapter 4.3.5) can serve as a striking example for a total change in a seed’s oil composition. Comparing two sorts of traditional rape with two species of low erucic acid content, a dramatic change can clearly be seen (Fig. 4.2); this change has led to a tremendous increase in rapeseed production. Erucic acid has been bred out of rape with only negligible amounts remaining. Today, rape oil can be used for human consumption in unlimited proportions. In addition to selling the oil, marketing the extraction cake and meal is also essential; thus, restriction can also come from that side. Along with its changed fatty acid composition, rapeseed is also a good example for the changes in the meal composition. It was the cultivation of OO-species that heavily improved the usage of rape’s nonfat portion. This change is of equal importance to the breeding of low-erucic varieties, because the commercial success of the oil milling industry
Vegetable Fats and Oils
179
Fig. 4.2. Comparison of old HEAR rapeseed fatty acid composition with recent LEAR types (after Weiss 1983).
also depends on the marketability of the meal and new high-oleic species that excited the market place (Table 4.3). From 1992, the Commission of the European Union began to subsidize only rape seed with a content of c20 pmol of glucosinolates/g of air-dried seed. This created political pressure on the West European farmers to grow only the new varieties. TABLE 4.3 Comparison of Novel and Traditional Oilseeds ~
~~
Content in air-dried seed Rape varieties Variety Traditional Double-zero Planned
GIucosi nolates
Sulfur
(mol/g)
(mg/g)
70
4.5 2.0 <1.3
30 <20
New varieties of high oleic oilseeds compared with traditional seeds Oleic acid content (%) Seed Corn Sunflower Safflower Peanut (African) Rapeseed (LEAR)
High oleic seed
Traditional seed
65-80 80-90 75-80 75-80 85-90
33 24 13 59 56
180
Fats and Oils H a n d W
TABLE 4.4 Examples for New Cultivations with Noncharacteristic Fatty Acid Composition Approximate fatty acid composition (%)
Soybeans 56 4 21 8 10 traditional 61 7 3 25 4 low palmitic 9 4 49 2 36 low linolenic 20 8 16 48 8 high stearic 27 4 15 45 9 high palmitic 8 3 63 24 2 high oleic 2 70 4 15 2 high oleidlow saturate 4 76 high oleic 8 3 8 3 85437 low linolenic, high oleic 1-2 2 high stearic 18-34 10-14 8-1 o 38-53 7-9 9-1 0 42-48 20-34 high linolenic Sunflower seed traditional 7 5 24 63 0 4 high oleic 6 85 5 0 4 high oleic, 80 4 80 10 0.1 high oleidlow stearic 4 2 88 5 0 Rapeseed (Canola) 2 56 4 traditional 21 10 4 high oleic 2 80 6 6 4 high oleic 2 70 15 3 3 83 4 high oleic 6 4 >90 high oleic Linseed 7 traditional 4 20 17 52 Linola (high linoleic) 6 4 16 72 2 Extreme varieties c12:0>50%; c,2:0 + c1,:o > 60% Rapeseed (Canola) Cocoa butter alternatives Rapeseed (Canola) High content of medium-chainfatty acids (MCFA) Rapeseed (Canola) High content of medium-chaintriglycerides (MCT) Rapeseed (Canola) Soybeans C18:o > 30% C22:1 > 75% Rapeseed (Canola) Ci,:, > 90% (1997), Ci,:, > 95% (2002) Sunflower seed C1&, > 90% Sunflower seed Corn Oil content > 8%
Pioneera Pioneera Pioneera Pioneera Pioneera SVOb DupontC Dupontd Dupontd Dupontd
PimP SVOb PioneeP
Pioneera SVOb Duponte Lembkef
CSlROs Calgeneh Calgeneh Calgeneh Calgeneh Duponte Lembkef Pioneeri SVOb Dupontd
apioneer International Inc.; ~ V specialty O ~rcductsIK.;Slabas 1995;BrogIie I 997;Sader 1993;krauen 1997;Wnited Grain Growers and Haumann 1990; hVoelker 1997;$atu 1997.
The freedom of influence that plant breeders have on the plant’s composition becomes apparent when traditional types are compared with new cultivations (e.g., safflower, Fig. 4.3). Recently, high-oleic varieties of many species have been developed to improve the oil’s oxidative stability, mainly during deep frying. Seed oils with noncharacteristiccompositionhave been bred and will be cultivated soon (Table 4.4).
Vegetable Fats and Oils
181
Fig. 4.3. Influence of the genotype on the fatty acid composition of safflower seed oil (after Weiss 1983).
Not all varieties bred are interesting for farming. Some serve as intermediates for further breeding; others derive their importance from their genetic composition. Often, the germ of the seed has a different fatty acid composition than the seed (Fedeli er al. 1972). However, this is not used with the exception of corn and other germ oils (see Chapter 4.3.12). In these cases, the seed as such does not contain oil.
4.1.2 The Yield of Oil Fruit To convey an impression of the different external influences on the yield, some publications are referenced. To start with, the timing of sowing can influence the yield (Fig. 4.4). In some cases there are periods or points in time that lead to satisfactory results, followed by dramatic shortfalls in yield when sowing takes place later. Similar findings have been made by the authors regarding plant density. It influences the yield, the size of the seeds, their oil content and thus the oil yield, i.e., the most important criterion of the oil industry (Fig. 4.5). Even with much lower plant densities in arid regions, an influence can be detected. Here, however, it is minor. Higher plant density increases the oil content by 1% (Holt and Campbell 1984). Minimum and maximum yields of the seed (based on the oil content) lie between 1000 and 1600 kg/ton. Following simple rules that are different from plant to plant (e.g., a plant density of -60,000 plantsha for sunflower), the yield can be tremendously increased-in this example, by 60%. Sawan et al. (1993) showed that plant density also has some influence on the fatty acid composition. For cottonseed, he measured a linoleic acid content of 47.83% for fields with
Fats and Oils Handbook
182
Yield roo0 kglha]
-1
I,
Sunflower (Australia)
I
24
40
32
48
4
12
4
Week of sowlng
Fig. 4.4. Dependency of the yield on the sowing time (after Barkla and Pritchard 1980, Weiss 1967 and 1983, and Mukurasi 1978). 166,000 plants per hectare; 222,000 plants decreased it to 43.64% and with 333,000 plants per hectare, only 41.54% could be reached. The variety also has great influence. This holds true not only for the composition but also for yield. Observing different species of Canadian rape, it becomes apparent that, with the introduction of new varieties with new properties, the proSeed weight [g/lOOO seeds] Yield “000 kg/ha] 10 [
Oil content
[%I
40
20
40
60
80
100
120
140
160
180
Plant density [rounded; ‘000 plants/ha]
Fig. 4.5. Dependency of sunflower seed and oil yield on the plant density (after Barkla and Pritchard 1980).
Vegetable Fats and Oils
183
TABLE 4.5 Yield of Different Rape Varietiesa
Variety
Approved for cultivation
Target Turret oso Zephyr Midas Tower Regent Westar
1966 1970 1968 1971 1973 1974 1978 1982
Type
bushellacre
Yield relative (%)
++ ++
38.4 40.7 37.2 37.8 41.4 36.2 40.1 45.4
100 106 97 98 108 94 104 118
0 0 0 00 00 00
dSource: R6bbelen (1 984). b++, traditional variety (HEAR, high erucic).
duction yield is always lower in the beginning and then increases during further improvement (Table 4.5). In the beginning, the main attention of the breeders is given to the new properties of the seed and only later to yield improvement, while maintaining these new properties. It is striking that in the course of their development, all new sorts reach a higher yield than the traditional ones, thus making their acceptance by farmers much easier. In the example, the novel seeds are represented by low-erucic 0-rape as well as low-erucic low-glucosinolate 00-rape; the traditional species are higherucic high-glucosinolate (marked ++). The kind and quality of soil also influences the yield of oil fruit, as with all other plants. Weiss (1967) compares the yields of Kenyan soybeans grown on different soils. Plants grown on red effusive rock yield 500 kg/ha on average,whereas almost 1100 k g h a could be reached on loamy soil with some granite sand. Fertilization with phosphates increased yield by up to 15%. On the latter soil, fertilization had a more positive effect than on red effusive rock. The geographic location also plays its role. Figure 4.6 shows the influence of night and day temperature difference on the fatty acid composition of sunflowers. Linoleic acid content rises proportionally with temperature differences. The fatty acid composition is important, not because of higher yields, but because of the higher prices obtained for high-linoleic sunflower oil. This high-polyunsaturated fatty acid (PUFA) sunflower oil (for sunflower: high-PUFA = high-linoleic acid > 69%) has a price that is up to 20% higher compared with ordinary sunflower oil. Besides these effects, the influence of fertilization has also been researched intensively. There, the right combination of fertilization and irrigation is the key to success (Fig. 4.7). The amount and composition of the essential trace elements vary from plant to plant, naturally. An overview is also given by Weiss. Oklahoma State University showed the effect of irrigation on the yield of peanuts. Figure 4.8 illustrates that by keeping the plant density and the distance between the rows constant, the yield could be tripled.
Fats and Oils Handbook
184
Fig. 4.6. Dependency of the fatty acid composition of sunflower seed oil on the climatic conditions (after Robertson and Russell 1972).
The right time for sowing has been discussed briefly above. However, there is also the right point in time for harvesting. Mazzani and Allievi (1966), using the example of sesame seed, show that the yield can increase steadily until the right moment and then decrease sharply. The method of harvesting depends on the plant Yield [kgiha] 2500
2000
1500
1000
500
0
56
112
168
224
Nitrogen fertilizer [kg/ha] Fig. 4.7. Influence of fertilizers and irrigation on the yield of soybeans (after Henry and MacDonald 1978).
Vegetable Fats and Oils
185
Fig. 4.8. Dependency of plant density and irrigation on the yield of peanuts (after Weiss 1983, Oklahoma State University).
and the location (country). The plant determines to what extent mechanical harvesting is possible. This is mainly for oilseeds that are grown on a large scale. The oil fruit of tropical regions is derived mainly from trees. Because there are no seasons, the same tree carries blossoms, fruit and all stages of development in between. Therefore, harvesting remains predominantly manual. Efforts are being made to mechanize the harvesting process there also. In the next sections of this chapter (4.2 and 4.3), harvesting is described briefly according to species. The exploitation of all means of plant breeding and agricultural techniques has led to a substantial increase in yields, not only for the oilseeds grown in moderate climates (see Chapter 4.2.1), but also for tropical trees. Figure 1.8 shows this clearly for many countries. 4.1.3 Harvest and Harvesting Losses
Because harvesting and storage have a substantial influence on the quality of the oil and on the processing steps to follow, these are also briefly covered here. In 1967, Cramer stated that the production of oilseeds could be 32%higher if only the losses from weeds, pests, and plant diseases could be excluded (Table 4.6). Although these figure are relatively outdated, they still seem generally valid for some parts of the world as the progress in some countries is balanced out by negative development in others; the shift of oil fruit production to the industrialized countries, however, has improved the situation if viewed as a percentage of total production. In addition to these preharvest losses, 30% more is said to be lost as a result of unprofessional or inadequate treatment after harvesting (Booth 1984).
Fats and Oils Handbook
186
TABLE 4.6 Preharvest Losses in Oil Seed Productiona Cause
Loss (%)
11 10
Insect damage Plant diseases Weeds Total
11 32
Postharvest Losses in Developing Countriesb Country
Oilseed
Kenya Thailand Paraguay
Peanuts Soybeam Soybeans
Loss (Yo)
30 25-68 15
aSource:Cramer (1 967). bSource: National Academy of Science (1978).
Cramer estimated the losses to be -42 MMT,equivalent today to -13 billion US. $. Today’s estimates are losses of -10% of the world’s harvest. Taking into account the increased tonnage, as an absolute amount, this represents -55 MMT of oilseeds and oil fruit with a value of some 17 billion U.S. $. Table 4.6 also gives some loss figures that are taken fmm a study by the National Academy of Science (Postharvest Food Losses in Developing Countries, Washington, DC,1978).Losses caused by harvesting result mainly from not choosing the right time and the right equipment. Meeting both demands is much more difficult in high-acreage cultivation than in artisanal farming. Small areas can be harvested quickly when the right time of seed ripeness has been reached. Vast areas can be cleared only one after the other because of the need for capital-intensive machines that are available only in limited numbers. Harvesting sensitive seeds such as peanuts is more difficult mechanically than harvesting by hand, as is still done in the majority of African countries. Labor ram in industrialized countries make mechanical harvesting of such seeds psible, as they by far outweigh the possible decreases in yield. The slight disadvantages that industrialized farming may have for one or the other seed are overcompensatedby far by the better infrastructurein the postharvesting processes. These are mainly better drying, quicker transportation and better storage conditions. But even under the best possible conditions, harvesting loss cannot be avoided. A study of Ohio State University (Table 4.7) shows that, assuming optimal conditions in soybean harvesting, -3% of the beans will still be lost, compared with an average of 7%. In total, the losses are a sum of adverse preharvest effects such as insect damage, fallen seeds, weeds, broken plants, plant diseases, and rotting plants plus a number of negative influences during harvesting such as the speed of the combindharvester, the mesh size of the sieves, the cutting height, the speed of air during air classification, the revolutionary speed of the cylinder, as well as the threshing itself and the state of the plants.
187
Vegetable Fats and Oils
TABLE 4.7 Estimated Harvest Loss (YO) of Soybeans with 3 5 0 0 kgha Yielda Source of loss Shattering
Stubble Lodged Cylinder Cleaning Total
Average operation
Excellent operation
3.5 1.1 1.9 0.4 0.4 7.3
1.3 0.6 0.8 0.0
0.2 2.9
aSource: Ohio State University.
Like preharvesting, postharvesting losses result from a variety of reasons that can be categorized as biological, biochemical and physical. These influences, however, can be well controlled. Biological influences start with the consumption of the seeds by insects, birds and mammals (mainly rodents) and end with spoilage by microorganisms such as yeasts and molds. Processes that proceed in the seeds, such as germination, are worth mentioning. Biochemical processes are mainly oxidation and hydrolysis. These cannot be totally suppressed but are usually caused by incorrect or unfavorable storage conditions (e.g., temperature, moisture). They occur in particular when the seeds have had to withstand improper mechanical stress (e.g., splits, squeezes). In principle, oil fruit yielding pulp oil are much more sensitive than those delivering seed oils. Therefore, the latter are usually processed in the country of destination, whereas pulp oils are exclusively extracted in the country of origin. 4.1.4 Drying of Oilseeds
Oil fruit yielding pulp oils are quickly processed after harvesting in close vicinity to their place of origin. Therefore, only oilseeds are stored. Here, it is very important to lower the water content to a degree that stops all biological and enzymatic activity in the seed. The influence of the water content on the biological activity, represented by its most important parameter, the formation of free fatty acid (FFA), has been researched by many teams. As an example, Figure 4.9 shows this influence on soybeans (Robertson er al. 1985). Table 4.8 gives an indication of the maximum water content that allows for good storage; other authors report slightly different figures. If the moisture is higher than that noted, enormous spoilage of the seeds by microbiological attack is possible. Fungi can multiply explosively, hand in hand with a temperature increase caused by their biological activity. This temperature increase then creates ideal living conditions for thermophilic bacteria; their metabolism adds futher to the temperature increase. Christensen (1%8) observed a container holding nonventilated soybeans with a seed
Fats and Oils Handbook
188
Free fatty acids [%I
Free fatty acid [%] 12
12
SOOd
Soybeans
moisture
10
10
8
0
6
6
4
4
/ztUre
seed
2 0 '
0
0
4
0
12
16
20
24
20
0
Storage at 20°C [weeks]
4
0
12
16
20
24
20
Storage at 20°C [weeks]
Fig. 4.9. Free fatty acid formation in soybeans in relation to the seed moisture (after Robertson eta/. 1985).
moisture of 13.2%. After half a year, steady temperature increase could be observed, reaching as high as 93°C after a year. After a hole was made in the container, the temperature increased to 200°C within hours. The beans were totally rotted by a fungal inetion. Although conditions are rarely that drastic, maximum allowable storage time depends clearly on temperature and moisture (Fig. 4.10). Lower moisture represents optimal storage moisture. However, it must always be evaluated whether higher seed quality, which is equivalent to higher oil quality, pays back additional drying cost. Drying itself can be done at the ambient air temperature without any equipment as well as with the aid of dryers. Drying begins with removing outer moisture from all fresh seeds. Then the inner moisture diffuses to the outer parts, where it is TABLE 4.8 Maximum Moisture for Good Storage of Oil Seedsa Oilseed
Maximum water content (%)
Soybeans Copra Cottonseed Safflower seed Linseed Sunflower seed Palm kernels Rapeseed Peanuts aSources: Custafson (1 9761,Patterson (1 989).
13.0 7.0 10.0 11.0 10.5 10.5 8.0 7.0 11.0
Vegetable Fats and Oils Temperature
189
['C]
Fig. 4.10. Allowable storage time for soybeans depending on seed moisture and temDerature (after Spencer 1976).
Allowable storage time [days]
also removed. After some time, an equilibrium between the ambient atmosphere and the seed is reached. This equilibrium depends on the ambient temperature and the relative humidity of the surrounding air (Table 4.9). Because relative humidity is temperature dependent, the relative humidity at 30°C must be 20% higher to yield the same seed moisture compared with 10°C (Fig. 4.11). Detailed information on the energy needed for seed drying is given by Bernardini (1985), for example. Seed hulls and stems may serve as fuel for the dryer if they have no better use. Drying can be carried out in horizontal dryers in which the seed is transported countercurrently to the hot air or in horizontal rotating cylinders. The temperature of the drying air is 250°C. Assuming that the dryer is being fed with air of this temperature and that the seed is to leave the dryer at 70°C, dryers with a cylinder diameter of 1.25 m (4 ft) and 10 m length (30 ft) have a throughput of 50 todd. Doubling the cylinder length and increasing its diameter by 50% increases the throughput to 200 todd. Rotary dryers are best suited for quick drying of very wet material (Fig. 4.12). TABLE 4.9 Seed Moisture in Hygroscopic Equilibrium with the Relative Humidity of the Storagea Seed moisture in equilibrium (% at 25°C) Relative humidity in air
31 .O 43.0 51 .O 62.0 71.2 81.1 93.0 aSources: Ramstadt (1942), Lamour (1 944).
Sunflower seed
Soybeans
6.1 7.4 8.3 10.4 12.2 16.4 25.1
5.2 6.3 6.9 8.1 9.5 11.7 16.9
Fats and Oils Handbook
190
Relative humidity [%I 100
20 %
18 % 16 % 14 % 12 % 10 %
9080 -
70 -
Moisture content of soybeans
60 50 40 0
5
10
15
20
25
30
35
40
Temperature ["C]
Fig. 4.1 1. Seed moisture of soybeans depending on relative humidity and temperature. The seed is fed (A) and transported into the drying cylinder (C) by a bucket elevator (B). The seed is collected in (D) and discharged. Hot air delivered by the boiler (E) is blown countercurrently through (C) and is sucked off via (F). Dust is separated and collected in (G) (Fig. 4.13). Besides these dryers, there are other types for drying of less wet seed, such as soybeans (Fig. 4.14). These consist of cells (fed via A) that are passed through by the seed that leaves the dryer at B. During the passage, the seed is exposed to a countercurrent stream of hot air that enters at C with a temperature of 75-95°C. The less moist air from the lower parts
0
2
4
6
8 1 0 1 2 1 4
Length of Cylinder [m]
Fig. 4.12. Temperature during drying of oilseeds (after Bernardini 1985).
Vegetable Fats and Oils
191
A
Fig. 4.1 3. Rotationary seed dryer.
1”1
Fig. 4.14. Vertical seed dryer.
Fats and Oils Handbook
192
of the dryer (C and D) is recirculated, and the very moist air from E is released to the atmosphere at 3545°C.The recirculated air from D has to pass a filter (F) before being reheated, in order to avoid ignition of dust particles. The energy consumption for drying can be enormous. It depends on the amount of water (W, kg of water per ton of seed) that has to be removed. W can be calculated from the initial water content (Wi) and the water content of the dried seed (Wd) as follows: W = (Wi - Wd) . 10[kg H,O/ton seed]
~4.11
To calculate the energy needed for drying, not only the water to be removed but also the temperature of the air injected and sucked off must be considered. Apart from that, the relative humidity of the drying air plays a role. During drying, the dried seed is heated up and this energy also has to be factored in. To calculate the technical data for dryers, the specific heat of the seeds can be assumed to be 0.5-0.6. Following a calculation by Bernardini (1985), drying a seed with a thermal efficiency of 60%, an air temperature of 20°C when entering the boiler and a temperature of 100°C when feeding the dryer, energy consumption ( E ) can be calculated as follows:
E = 49,960 . W [kT/ton]
r4.21
Drying the seed makes sense only if carried out to a level of seed moisture that improves storage stability and does not deteriorate the seed’s mechanical stability. Furthermore, attention must be paid to the fact that the seed is in equilibrium with the ambient air,a state that depends on the relative humidity of the air in the storage. This equilibrium seed moisture is re-established during storage, independent of the moisture level that the seed had been dried to before (see Fig. 4.10). It is therefore important to maintain adequate storage conditions after drying. 4.1.5 Seed Storage
Despite good drying and good storage conditions, aging of the seed continues, so that storage time cannot be unlimited (Fig. 4.15). During aging, positive effects for oil processing such as decreasing enzyme activity go hand in hand with negative effects such as a tendency toward peroxidation. Measuring a seed’s ability to germinate is a good method of estimating the stress seeds are exposed to during storage. The two are inversely proportional. Many a paper exists that correlates germination ability with storage duration, storage temperature and relative moisture. There is the commercial aspect, namely, that seeds that are well stored and transported have fewer FFA and are less oxidized, thus yielding higher prices. There is also the quality aspect. Damage to the oil cannot be totally removed during processing, and in any case, such oils require much more severe treatment. It is recommended that seeds be well ventilated if stored for a long period of time. A temperature range of 4-1O’C helps because it dramatically slows down all
Vegetable Fats and Oils
193
I
+
lmpairud synthesis of enzymes
Continuous nuclease activity
I
+
+ of major enzymes
Loss of ribosome integrity
Ribo-
I
Impaired protein synthesis
I and DNA polymerase
Failure of synthesis of functional RNA
wed viability
I
and template activity
7 endodesoxyribonucbase --t
Aaina of dw seed
+
nucleus Aging of dry seed
+
&ins of dry seed
+
Fig. 4.15. Biochemical processes during aging of seed (Chavan e t a / . 1984).
biologic aging processes; furthermore, insects can no longer tolerate the living conditions. In addition to maintaining adequate temperature and moisture levels, attention must be paid to mechanical stress. The pressure that is imposed on the seeds depends on the height of the silo (when filled) and the seed’s bulk density. Because there is a limit to mechanical seed stability, losses also occur from this aspect of storage. The volume stream is also very much influenced by bulk density (Table 4.10). Of course, for storage conditions and silo construction, bulk density is not the determining factor in itself but rather in its combination with seed stability, a factor that varies from seed to seed. Often during cultivation of new sorts, higher oil yield results in seeds with a thinner hull, leading to less mechanical stability and thus to oil losses by splits during storage. Seeds can be stored in metal or concrete silos or in halls. Metal silos are well suited for small volumes or as intermediate stores at the farms. The wall strength
Fats and Oils Handbook
194
TABLE 4.1 0 Bulk Density of Oilseeds Bulk density (@) Soybeans Cottonseed Cottonseed delintered Cottonseed dehulled Sunflower seed Peanuts, whole Peanut kernels Palm kernels Rapeseed Copra (dep. on size) Safflower seed Linseed Sesame seed Grape seed Castor beans
750-780 280-320 480-580 550-650 4W50 280-330 630-650 56-0 650-720 300-500 700-740 680-720 590-630 470-520 550-590
should be higher than that calculated for normal stability. For a silo 4 m (12 ft) in diameter and 10 m (30 ft) in height, the minimum wall should be 2 mm; among other reasons, this is to prevent heavy deformation in the upper part during (too) quick emptying (Bernardini 1985). Table 4.1 1 gives some storage capacities. For big bulk storage, concrete silos are preferred. The usual layout is square, octagonal or round, usually grouped to improve mechanical stability. Silo height is limited to the mechanical stress that the seed can stand. If pressure (i.e., height) is too great, the lower seed layers can become extremely damaged. Furthermore, there is a danger of bridge formation. Extreme forces that may damage even the silo itself can be set free if such bridges break. Storing soybeans in a silo 50 m (150 ft) in height, for example, puts the lower layer of beans under a pressure of 4 bar. In a round silo 10 m in diameter and 50 m in height, -2700 ton of beans fall down when a bridge formed at a height of 5 m breaks. Spencer (1976) found during his trials that 95% of broken beans consisted of major parts, but that 5% of the splits werepo small that they were removed as “impurities” during seed cleaning. For this reason and for reaTABLE 4.1 l Storage Capacity of Silos Amount of stored seed (tondl0 m height;1000 IbdlO ft height) Silo format (grid 10 m) Round Octagonal Square
Soybeans -600 -700 -850
-85 -95 -120
Sunflower seed -330 -380 -460
-45 -55 -65
Rapeseed -510 -600 -730
-70 -85 -100
VegetableFats and Oils
195
Cracked seed 1% after threshing] VU
30 -
20 -
10-
0 -
I
Fig. 4.16. Relationship between seed moisture and rate of split rapeseed (after Appelqvist and Johansson 1963).
sons of oil quality, splits should thus be avoided. However, it is clear that they cannot be totally avoided, especially not during filling of the silos, when beans crash onto the silo’s floor or onto other beans. The portion of splits does not depend only on the height of the fall, but also on the elasticity of the seed, which is usually associated with its moisture (Fig. 4.16). The results obtained after mechanical stress by threshing can be transferred to storage. Generally, the height of silos should not exceed five times their diameter (Table 4.12). Cottonseed is traditionally stored in large warehouses that allow for storage of up to 1 MMT. Usually a conveyor belt under the roof and central ventilation in the lower part, as well as a tunnel for inspection walks are installed. The storage must be well ventilated because remaining linters act as insulation. Normally there is a cooled wooden floor. Storage of copra, unlike all other seeds, requires special care with the conveying equipment. All other oilseeds are uniform within the same type with very limited differences in size, whereas copra is very irregularly broken, with some small TABLE 4.12 Amount of Broken Beans After Bouncinga Proportion of broken beans (YO) when falling onto Falling height -m (4%) 30 (100) 2 0 ( 60) 10( 30) aSource: Patterson (1 989).
concrete
beans
4.5 2.1 1.1
3.2 1.4
0.7
Fats and Oils Handbook
196
pieces and others that may be as large as 10 cm. Buildings for copra storage are usually lightweight construction halls to which it is delivered directly by truck. All other seeds are stored on the floor of simple halls or silos of different forms. 4.1.6 Transport of Oilseeds
Transport outside the factories is by truck, rail or ship, where special care has to be taken to ensure dry compartments and to carefully check previous cargos. In the factories and in loading or unloading, various conveying equipment is used. These include belt conveyors (horizontal or maximum 20"slope), screw conveyors (horizontal or steep slope), conveying trough, bucket elevator (vertical), sliding cell or chain conveyors (horizontal and vertical), pneumatic conveyors (horizontal and vertical) and suction air conveyors (horizontal and vertical). Belt conveyors allow fast transportation of a large volume at low energy consumption. Because of their open construction, they are easy to maintain and not very sensitive toward foreign material (e.g., metal pieces, stones). However, they are also open for further contamination. The belt runs via two or three V-shaped rolls that form an angle of 10-30". It is driven on the one side and tightened on the other. Slopes of >20" are almost impossible to engineer (Figs. 4.17 and 4.18). Screw conveyors (S) have the advantage of transporting the seed in a closed sys tem if the screw runs in a pipe. It can also run in a U-shaped trough (trough conveyor; T). If the pipe is built as a sieve, they are called sieve conveyors (Fig. 4.19). These enable the separation of small foreign particles and dust from the seed during transport without extra effort. Screw conveyors are designed to swivel and allow for transport even at steep angles (if built into a pipe, even vertical transport). Their one disadvantage is their straight construction, which makes it impossible to pass obstacles without interruption. The other is the high shear stress that can lead to unwanted damage of the seed. The conveying capacity (C,) can be calculated as follows: Cs= ( & . R . r . S . 6 . X . 60. ~)/4000(to&)
[4.31 where d (m) is the diameter of the screw (pipe), x (5%) is the degree of filling, s (m) is the slope of the helix, r (min-1) is the rotational speed of the screw, 6 is the bulk density, and v is the loss factor if not conveyed horizontally (8 -15' + v = 0.7; 8 -25" + v = 0.5). The slope of the screws may differ in the same screw over its length. The slope close to the feeding point determines the amount conveyed. Figure 4.20 shows the conveying capacity of different types of screw conveyors for a filling factor of 33%. For extraction meal, a filling factor of 30% is common; for oilseeds, 45% can be assumed. Free-flowing materials can have up to 40% higher throughput; nonfree-flowing goods may result in 20%less. Pipe screw conveyors (P) have a 2-2.5 times higher capacity than trough screw conveyors (T), given the same screw diameter and revolution speed. For vertical transport, capacity decreases significantly. To allow the same capacity as for horizontal screw conveyors, transporting vertically (V), the revolutionary speed of the screw has to be five times higher.
(a)
Vegetable Fats and Oils 197
Fats and Oils Handbook
198
Belt conveyor -A)
v=1.3
w=600
"B)
v=1.2
w-500
+C)
v=1.2
w=450
*D)
v=1.2
w=400
*E)
v=1.0
w=350
+F)
v=1.0
w=300
v = belt velocity [m/sec] w = belt width [mm]
Fig. 4.18.
Energy consumption of belt conveyors and quantity conveyed (after Bernardini 1985).
The energy consumption (E,) for the conveyor can be calculated as follows:
E, = L . C, (f k sin 0)/367
(kW)
i4.41
where L (m) is the total length of conveyor, C, (ton/h) is the conveying capacity for screw conveyors (see Equation. [4.3]),fis the product specific factor (f= 2 for oilseeds and extraction meals) and 0 (") is the slope. As can be seen from the equation, the energy consumption increases linearly with the length of the conveyor and the amount conveyed. The slope 0 adds a nonlinear part to the equation. For vertical transport, bucket elevators are more suitable. They consist of a chain of buckets that can hold the conveyed product. Close to the top, these buckets are turned upside down for discharge (Fig. 4.21). The amount conveyed for such equipment can be calculated as follows:
i
E
Fig. 4.1 9. Screw conveyor.
Vegetable Fats and Oils
199
1OOO.D where C, (tonih) is the conveying capacity for bucket elevators, B (L)is the content of the individual bucket, v ( d s ) is the velocity of the bucket, x (%) is the degree of filling, 6 is the bulk density and d (mm) is the distance between the buckets. The degree of filling is reduced with increasing bucket speed; it increases with the slope of the conveyor. German Industrial Standards (DIN) define the bucket size and the corresponding quantities conveyed for granular products (DIN 15232) and for oilseed meals (DIN 15231; Fig. 4.22). The energy consumed (E,) can be calculated according to Equation [4.6]; energy to be installed (Ei) is expressed by [4.7]. Equation
(a)
where g (m/s*) is the acceleration due to gravity, h (m) is the conveying height, Ps (kW) is the conveying power input, PN (kW) is the no load power input and o is the efficiency. Redler conveyors consist of open rectangular or square boxes that slide on a fixed belt and transport the goods by dragging them along. They are able to cope
\
500-
R = Revolutionary speed (min-’)
D = Diameter of the screw (mm)
T
Screw conveyors
4001 300
Trough conveyor (T)
Vertical conveyor
N’
200
.
100
0 R= D(T)= D(P)=
20
1250 975
40 630 630475
240 80 100 200 250 290 165 385 290
80 315
280
215
320 =DO
Fig. 4.20. Quantity conveyed by screw conveyors depending on screw diameter and revolutionary speed.
200
Fats and Oils Handbook
Fig. 4.21. Bucket conveyor.
Fig. 4.22. Quantity conveyed by bucket conveyors at 90% filling.
Vegetable Fats and Oils
201
with steep slopes and to convey large bulk. Energy cost is relatively high as a result of the high frictional forces that have to be overcome. In contrast to the conveyors described above, it is possible to heat or cool the conveyed goods. This principle is also applied in solvent extraction (see Chapter 5.2.3.4.3). A Redler with a chain height of 25 cm and cells of 30 x 40 cm has a throughput of -60 m3/h if running at 0.2 d s (see also Fig. 4.23). Chain conveyors work similarly. Instead of a cell, runners, wings, scrapers or U-shaped track links are dragged over the belt, dragging along the goods. If the distance between the links is narrow, chain conveyors can manage almost all transitions from horizontal to angled operation. Figure 4.24 shows the amount conveyed for a bulk density of 600 g/L and a speed of 0.1 d s . Pneumatic conveyors allow transport of goods in whatever direction wanted. This flexibility must be paid for by an energy consumption that is four to five times greater than with the other conveying systems. However, the goods are transported more gently than with most mechanical means. A problem is caused by the dust, so that filters have to be installed. Air speed required is -20 d s ; the ratio of air to goods conveyed is 1.2.
-
4.1.7 Storage and Transport of Oils
In contrast to almost all other oils that are extracted in factories located close to the consumer, palm oil and its fractions are processed in the neighborhood of the plantations and then shipped. Consequently, other precautions have to be taken to safeguard quality. PORul (Palm Oil Research Institute of Malaysia, 1985) has therefore published recommendations that guarantee maintenance of optimum quality; some of them were derived from the Codex Alimentarius or later found their way Quantity conveyed [rn3/h] I "
h = 220 rnrn
60 -
Sliding cell conveyor
50 v = 0,2 (rn/sec)
40 -
h = 175 mrn
30 -
h = 150 rnrn
20 10-
0
Fats and Oils Handbook
2 02
Quantity conveyed at 0.6 kg/dm3 bulk density
speed
800
[m/secl 1 .o
Chain conveyor 600 -
0.8 0.6
400 -
0.4
200
140
0.2
240
440
340
540
640
Chain width [mm] Fig. 4.24. Quantity conveyed by Redler conveyors depending on their size.
into that codex. Examples for contracts and international trading terms can be found in Ludwicak (1990), Fleming (1990) and Backlog (1990), for example, and from the International Association of Seed Crushers (Anonymous 1980). Following these recommendations, ship tanks that are not stainless steel should be coated with an appropriate coating. Copper, brass and bronze should not be present. The tanks must be heatable; however, to avoid local overheating, heating should not be faster than 5'Ch if agitation is not possible. To ensure good loading and unloading, the temperatures given in Table 4.13 should be guaranteed. TABLE 4.13
Recommended (Un-)LoadingTemperatures for Oils and Fat@ ("C)
aSource: Ccdex Alimentarius (1 992). %fees above slip point.
(OF)
Max.
Min.
Max.
55 70 35 35 35 25 25 ambient 25 25 30 55 60 15b lob
112 150 86 86 86 68 68
131 158 95 95 95 77 77 77 86 140 2 76
Min. Palm oil Palm stearin Palm olein Palm kernel oil Coconut oil Cottonseed oil Peanut oil Other salad oils Fish oil Tallow Hardened oils
Temmrature
50 60 30 30 30 20 20
77 131 186
Vegetable Fats and Oils
203
TABLE 4.14 Recommended Storage Temperatures for Oils and Fat9 ("C)
Palm oil Palm stearin (hard) Palm olein Palm kernel oil Coconut oil Seed oils Tallow
Temperature
Min.
Max.
32 40 25 27 27
40 45 30 32 32 ambient
44
49
(OF)
Min.
Max.
90 104 104 113 77 86 81 90 90 81 ambient 111 120
aSource: Codex A h e n m i u s (1992).
Such temperature recommendations are also given for storage to prevent crystallization, which causes inhomogenity (Table 4.14). Reliable producers ask for a record of previous freight from the transportation companies to avoid contamination; they can then decide whether the ship or truck is suitable for the transport of seeds or oils. The method of transport depends mainly on the fat or oil transported. Crude oils will be refined after transport; thus, conditions do not have to be well controlled. They can be transported and stored in large tanks. The more refining an oil has undergone, the less one has the ability to compensate for damage during storage. Such oils are therefore transported and stored in quantities that can be used up within days. Fully refined oils may require transport and storage under nitrogen. In this case, it can be more important to protect the oil film on the walls of an empty vessel from oxidation (large surface exposed to oxygen from the air) rather than saturating the headspace of a full tank with nitrogen. For transport tankships, rail tankers and trucks can be used. The further the oil has been processed, the more road transport is chosen, because this is usually much faster, with less aging of the product. The tanks themselves can be made from mild steel or stainless steel. The kind of vessel chosen depends on the oil and the pretreatment. Mild steel containers should be flushed with hot oil several times before their first usage. This creates an oil film on the surface that mildly polymerizes and forms a sort of coating, protecting the oil from iron intake, which catalyzes autoxidation. 4.1.8 Usage of the Nonfat Part of Seeds
Besides the fats and oils that are delivered by the oil fruit, special attention has to be given to the use of their nonfat part. On the one hand, this means dealing with those parts that are not suited for human consumption such as shells of babassu nuts or peanuts or the stems of palm fruit. To a greater extent, this means marketing expeller cakes and extraction meals that remain after separating the oil. The
Fats and Oils Handbook
2 04
commercial success of an oil mill is closely linked to the ability to sell these meals at reasonable prices. This is more evident if one has in mind that the nonfat part usually accounts for >50% of the seed weight, and even as much as 80% for the dominant seed soybeans. As early as the year 1700, the idea arose to use the oil cake that had formerly been thrown away as feed. From 1900 onward, real research on its usage has been started and has answered the question of which oil cakes are suitable for which animals. The use of the meal is restricted in many cases because it contains natural components that cannot be fed to certain groups of animals, or at least only in limited amounts. Often these restricting components can be removed or inactivated by additional meal treatment. In some cases, new species have been bred to improve the usage of the meal. In the following, some examples are given to illustrate common uses. A broad and detailed overview can be found in Lennerts (1984). Most restrictions in meal usage are covered briefly in the section describing the respective oil plant. In case of feed-stuff for livestock, it is very important that the meal contain some components, usually special amino acids, in sufficient quantities and that these also be easily accessible to the animal. This means that digestibility must be ensured. A key quality factor for a feed protein is the concentration of available lysine (Table 4.15). TABLE 4.15 Amino Acids in Soy Protein from Dehulled and Nondehulled Seed, Soybean Meal and Rapeseed MeaP Soy protein Proportion (%)
Dehulled
Nondehulled
Soybean meal
Alanine Arginine Aspartic acid Cysteine Glutamic acid Glycine Histidine lsoleucine Leucine Lysine Methionine Phenylalanine Proline Serine Threonine Tryptophan Tyrosine Valine
4.6 6.9 11.5 1.5 19.2 4.4 2.6 4.7 7.7 6.4 1.5 4.8 5.1 5.6 4.0 1.3 3.3 4.8
4.0 7.0 11.1 0.9 16.3 3.9 2.4 4.4 7.2 5.8 1.2 4.6 4.7 4.9 3.7 1.3 3.3 4.6
1.9 2.9
aSource:DLC, from Lennerts (1985) and Clandinin (1978).
0.3 8.1 2.1 1.1 2.1 3.4 2.8 0.6 2.2 2.3 2.3 1.7 0.5 1.3 2.3
Rapeseed meal 1.6-1.7 2.1-2.2 2.5-3.1 0.2-0.5 6.4 1.a-i.g 1.o 1.3-1.5 2.5-2.7 2.1 0.7 1.4-1.5 2.3-2.7 1.6-1.7 1.6-1.7 0.4 0.8-0.9 1.&1.9
Vegetable Fats and Oils
205
TABLE 4.16 Digestibility of Soy Meala ~~
~
Digestibility of soy meal components (%) Non-heat treated
Heat treated
52 68 44
63 82 52
Dry matter Crude protein N-free extract
aSource: Niveld and Terpstra, from Lennerts (1985).
Digestibility can be increased by heat treatment (toasting, see Chapter 5.4). In the case of soybeans, it can be improved by 20% (Table 4.16). However, this is less than the difference in digestibility for different sorts of livestock and poultry. Extraction meal from dehulled seed contains fewer trace elements and fewer vitamins than that from nondehulled seed. However, that plays a minor role compared with the protein portion that is increased by dehulling (Table 4.17). The meal is further processed for feed-stuff, which is usually regulated by law. As an example, the German regulation for different sorts of sunflower meal is given in Table 4.18. The composition of the meal is given in the respective sections dealing with the individual oil plants.
TABLE 4.17 Trace Elements and Vitamins of Soy Meala Proportion (ppm of dry matter)
Proportion (ppm of dry matter)
Trace element
Nondehulled
Dehulled
Vitamins
Nondehulled
Iron Manganese Zinc Copper Molybdenum Iodine Cobalt Fluorine Chromium Nickel Barium Aluminum Boron
130.0 27.0 55.0 15.5 3.6 0.5 0.25 4.7 1.o 16.0 6.7 32.0
122.0 25.0 48.0 14.0 3.8
Vitamin E
1.2 6.7 3.2 4.8 27.0 16.0 0.6 2800
-
0.08 2.1
36.0
aSource: Kling and Wohlbier (1983) with permission
Bl BZ Bb
Nicotinic acid Pantothenic acid Folic acid Choline
Dehulled 1.3
-
Fats and Oils Handbook
206
TABLE 4.1 8 Standardized Sunflower Meals According to German Regulations Standard (% of dry matter) Water Sunflower cake Dehulled Partially dehulled Nondehulled Sunflower meal Dehulled Partially dehulled Nondehulled Sunflower meal, fat added Dehulled Partially dehulled Nondehulled
Fat
Fiber 46
4 3 4 3 4 3
<27.5 <30
4 3 4 3
>4
4 3
>4
<13
>4
<27.5 <30
<13 4 3 4 3
>4 >4 >4
46
<27.5 <30
Proportion in standard types (%) Water
Fat
>3 8 >5 >2 9 >5 no standard type
>40 >30
Fiber
<2 1
<22
no standard type no standard type no standard type no standard type
4.2 Pulp Oils Pulp oils occur finely dispersed in the fruit's endosperm, which has a very high water content. They require special treatment, preferably immediately after harvesting. Any mechanical stress that leads to damage of the cells, but also aging as such, initiates enzymic reactions that lead to fat splitting or other spoilage. This means that pulp oils are usually extracted in close proximity to the location of origin, which usually is smaller decentralized oils mills near the plantations. In addition to the two main contributors (palm oil and olive oil), there is a third that is produced in small quantities, namely, avocado oil. This oil is very edible; however, because of its high price, low tonnage and high image, it is used mainly in cosmetics. 4.2.1 Palm Oil ----4.2.7.7 Betany and History of the O i l Palm. In Europe, the- P
r Gil Eannes in 1434 first reported about oil palms (Elueis guineensis). Today, they flourish mainly in the western part of Africa, Indonesia and Malaysia, recently also in Brazil and more recently in Colombia. Oil palms grow to 20 m in height and grow best at temperatures of 24-27'C. They require a humid climate. Cultivated oil palms carry fruit from their fourth year onward. Palm fruit can then be harvested for 40-50 y with the maximum yield being reached after 12 y (Fig. 4.25). In plantations they are replaced after -25 y. The palm is the oil producer with the highest yield; each tree can produce almost 20 MT of fruit bunches per year. In addition to the trees from plantations, wild palm trees are also used as a source for palm fruit. However, these carry fruit only after 10 y and at lower yields.
Vegetable Fats and Oils
207
Fig. 4.25. Oil palm and oil fruit.
New cultivations stay -30% smaller to allow for easier harvesting. Oil palms are one of the best examples of the cloning technique in modern agriculture (Unilever 1985). For cloning, samples of the root of a high-yielding robust oil palm are taken. They are placed in a special nutrient medium where the cells of the root begin to multiply. The mass formed is known as the callus. From the callus, tiny oil plantlets begin to grow. These plantlets are transferred to different culture media at various stages of growth to provide them with the nutrients they need. While still in test tubes, they are kept in controlled environments. Later, they are transplanted into polybags and shipped to the plantations. Because these piants may be grown from many different palm species (Jones 1984), new methods of breeding arise (Tan et al. 1985).However, cloning is still the exception.
208
Fats and Oils Handbook
Pollination of the palms had been done manually up to the 1970s using especially designed bellows attached to a long pipe to blow pollen onto female flowers. Oil palms flower for 3-8 d and only one third of the blossoms bear fruit. After importation of oil palms to Malaysia, New Guinea and the Solomon Islands, the palms bore fruit only when manually dusted. In 1977, an entomologist from the Commonwealth Institute of Biological Control was put in charge by Unilever to investigate the case. He discovered that, contrary to long held belief, the plants were not wind pollinated, but in fact insects did the job in Africa, their country of origin. In particular weevils of the genus Elaeidobius (see Fig. 4.26) had developed a symbiotic relationship with the palm and were the principal agents involved. These were not present in South East Asia. In some areas, a local insect (Thrips hawaiiensis) had taken over the job. However, it was much less effective. Only after the influence of the beetle on the fauna of the “importing” countries had been carefully investigated and found not to be at all harmful to the ecological equilibrium of the host country were Elaedobius weevils brought to Malaysia in 1981. The yield of the palms immediately increased by up to 50%. New plantations added to the trend, and the supply of palm oil from South East Asia has risen substantially over recent years (see also Patzaris 1985 and 1986). A large part of the supply, especially the olein from fractionation (see Chapter 6.2.3.4) is consumed in the region as salad oil. 4.2.7.2 Composition and Properties of Palm Oil. African oil palm contains 40% pulp, the Asian varieties up to 65%. The pulp itself contains -40% oil (Fig. 4.27).
Fig. 4.26. Elaeidobius kamerunicus.
Vegetable Fats and Oils
2 09
Poor keepability of the fruit leads to immediate processing of the pulp close to the plantation; palm kernels, however, can be stored longer and transported without difficulties. Palm oil is rich in palmitic and oleic acid, adding up to almost 80% of the fatty acids. In some oils, up to 0.8% palmitoleic and linoleic, as well as 1.1% arachic acid, may be present (Fig. 4.28). Special coverage of African palm oil can be found in Congopalm (X) and of Malaysian palm oil in Berger (XV). Because of its composition, palm oil consists of two main fractions that are liquid and solid, respectively, at moderate ambient temperature. This makes it especially suitable for the above-mentioned fractionation (see Chapter 6.2). The triglycerides present in palm oil and their proportion underline these properties (Fig. 4.29). 4.2.7.3 Economic Importance of Palm Oil. Palm oil supply has increased sharply over the last two decades (Table 4.19) because of the vast increase in pro-
Oil palm fruit
Fig. 4.27. Composition of palm fruit.
Fats and Oils Handbook
21 0
Fig. 4.28. Main fatty acid composition of palm oil.
Palm dl TrigC=*
typs
PPP PMP, MPP. PPS, PSP sss, SPS, PSS
-
MOP POP POS
sos PPO SPO, PSO,
sso-
Po0 SOO, MOO PLP MLP, SLP, PPL SPL, SSL, SLS
-
OOO MOL, POL. SOL MLO, PLO, SLO
-
OOL, OLO, P U others Proportkn [% Wrn]
Fig. 4.29. Triglyceride composition of palm oil (after Coleman 1961).
21 1
Vegetable Fats and Oils
TABLE 4.19 Palm Oil Production Palm oil (MMT)
1935
1950
1960
1970
1980
1990
1993
1994
Total world Nigeria Indonesia Malaysia
0.65 0.25a 0.30 0.05
0.90 0.28a 0.33 0.11
1.10 0.42 0.14 0.09
1.75 0.48 0.20 0.62
5.00 0.67 0.72 2.53
11.10 0.90 1.94 6.09
14.40 0.83 3.42 7.40
14.66
1995
15.60 0.84 0.87 4.10 4.30 7.22 7.81
aBritish West Africa.
duction in South East Asia, mainly Malaysia. The yield there increased from 2.8 toniha in 1878 to 3.4 ton in 1933, 4.5 ton in 1969 and up to 5.7 tonha in 1978 (Berger 1983). Today it is -4 t o h a on a worldwide basis with an additional 0.5 tons of palm kernel oil. Other areas that have a climate suitable for palm cultivation are trying hard to become self-sufficient or to extend their production for export. In Asia, this holds true mainly for the Philippines, and in South America, for Brazil and Colombia. Prices have dropped as a result of high stocks. Palm oil stocks of Malaysia had been estimated to reach 1 MMT in 1988 and more than that in 1989. In 1992, they were said to have decreased to 660,OOOtons with an ending stock in 1993 of -1.2 MMT. The production is expected to more than double from 1995 to the year 2020 with a production of -35 MMT. 4.2.7.4 Harvest of Palm Fruit and Oil Exfraction. Usually palm fruit bunches are harvested when five to Seven individual fruits have fallen from the bunch (TPI1971); however, this time point represents a compromise. Although some parts of the fruit are not yet ripe, the fruit has to be cut because others might become overripe. At this stage, they quickly begin to develop FFA, which causes a deterioration in oil quality. Bafor (1986) describes all of the p e e d i n g s during ripening. The fruit bunches are cut with long knives (old varieties) or with short knives or mechanically for the recent species. They have a weight of up to 40 kg and along with the pulp contain up to 2000 red brown oval nuts 3-5 cm in length and 2.5 cm in diameter. These are further processed to palm kernel oil, a lauric seed oil (see Chapter 4.3.8).One thousand kernels weigh -8 kg. The processing scheme for palm oil is given in Figure 4.30.
4.2.1.5 Fact File of Palm Oil. The fact file (Figs. 4.31 and 4.32 and Table 4.20) shows the physical data of palm oil, its composition and the development of world market prices. As for olive oil, virgin palm oils of the fmt pressing also exist and are only of local importance. More detailed information on palm oil is given in the references section. Palm oil is very well researched because marketing organizations exist that promote its use. Reports on its potential use have been published in recent years by Beny and Awang (1983), Ong (1984), Kheiri (1985), Traitler and Dieffenbacher (1985, cocoa butter substitutes), Okawachi et al. (1985, fat specialities) and Berger (1985 and 1986).In 1990, a palm oil congress was held in Hamburg; its proceedings also contain valuable infoimation.
Fats and Oils Handbook
212 Palm. fruit
(Bunchar) 2 . 5 3 bar, 130135'C, 50-75 min Autoclam (1.5 bb 20 t Wnt.nt); a p r d t y por Ilne Up I0 10 vh Inr&rtbn of lpolytic enrym; operho of calls
FNB l o o r e d up lo W.5% if Itrrllization b well dom Robthgdrwn WW b w ; cspdtypof U r n up to 32 vh
=.a cooking
9C-lOo'C, 20-30min 3 5 m' Content; (up lo 10 vh of who* bunchar)
-
S a m presses (up to 20 vh); maidurl oil < 7%, broken kernels < 5%
Vibraling rusen (Seprratlon of major bNbn material) t
t
CIPriRcslbn, wrrhing
+
Maling lo cn.W C
Nub
+
(W 4.3.8)
Fbn
a 8
Ciarificltmn. wrhw
r
Sewraton I-+
i Wno
>>> f FNB
~8-
Water < 6.1%
a
I
Burning material or brlngingbeck to p*ntotion aa hrtl(ber
Crude palm oil
Fig. 4.30. Flow chart of palm oil production.
I
Palm oil
IP r o P o [%I~ ~
Fatty add
MyMtic Palrnitii Palmitolek Stearic Oleic Linokic Linobnic Arachic
C 14:O C 16:O C 16:l C 18:O C 18:l C 18:2 C 18:3 C2O:O
< 0.4 2.0 47.0 0.6 3.5 6.0 36.0 -44.0 6.5 12.0 c 0.5 c 1.0
0.5 41.0
-
-
Proportion [%]
Fig. 4.31. Fact file of palm oil (fatty acid composition). 4.2.2 Olive Oil
4.2.2.1 Botany and History of Olives. Olive trees occur mainly around the Mediterranean where they have been established for centuries. Most likely the olive originated in Asia Minor. In the Bible alone, olives are mentioned more than 200
Vegetable Fats and Oils
21 3
Fig. 4.32. World market price development of palm oil.
times. For example, a dove brought Noah a branch of an olive tree as a divine sign that the flood was over. Most likely olives found their way from Asia Minor to Europe around 1700 B.c., approximately the time when Athens was founded. The Greek legislation of Solon, as recorded by Plutarch, fined anybody who cut more than two olive trees per year and per plantation; they recognized the importance of the trees. Around the year 700 B.C., olives came to today’s Italy, and by 200 B.C. they had spread over the whole of the Roman Empire. From Spain, at that time a Roman province, the oil reached as far as the British Islands in the second century. After that, it was almost completely consumed by the citizens of Rome and free trade became forbidden. TABLE 4.20 Fact File of Palm Oil German: Palmol
French: huile de palme
Relative density Refractive index Saponification value Iodine value Unsaponifiable matter
(at 50°C; ref. water 20°C) (nD40) (mg KOH/g oil) (Wijs method) (g/Kg oil)
Melting point Solids content at
0.891-0.899 1.449-1.455 190-209 50-55 <12
Solidification point
30-37OC ( O U T )
Spanish: aceite de palma
27-43T
10/50
20/68
30/86
35/95
50
27
8.5
4.5
(YO)
World market price (ex Sumatra)
Price index (1 995 average compared to average) 1 2 6% 10 years ago 20 years ago 148% 235% 30 years ago
(U.S. $/MT)
min
0
rnax
1962-1 994
144
393
937
1962-1 969 197CL1979 198C-1989 1990-1995
144 177 199 275
222 436 472 416
288 807 937 740
214
Fats and Oils Handbook
Fig. 4.33. Olive branches and fruit.
Olive trees need an average yearly temperature of 15-20°C. The evergreen trees are up to 20 m high and yield up to 55 kg of olives per tree; they can reach ages of over 2000 y (Fig. 4.33). 4.2.2.2 Composition and Properties of Olives. Taking the whole olive including its kernel, the oil content is -30%, on average; however, the yield after oil extraction by pressing is only a little above 20%; the kernel contains -12% oil with a composition that is similar to that of the pulp oil (Fig. 4.34). The pulp oil can contain up to 80% oleic acid. Besides the main fatty acids (Fig. 4.35), 0.2% lauric acid, up to 1.3% arachic acid, 2.5% palmitoleic acid and 0.1-1.7% myristic acid occur. The proportion of polyunsaturated fatty acids is low. The high image of olive oil is also based on its extraction technique that permits it to be left it in a so-
Fig. 4.34. Composition of olives.
Vegetable Fats and Oils
21 5
Fig. 4.35. Main fatty acid composition of olive oil.
called virgin state. The fatty acid composition varies greatly depending on the region of origin (Gracian et al. 1968, Fig. 4.36). The proportions of various triglycerides (Fig. 4.37) present the profile that can be expected from the fatty acid composition. The paramount triglyceride is the single acid triolein; oleic acid is present in 97% of all triglycerides. 4.2.2.3 Economic Importance of Olive Oil. The economic importance of olive oil is increasing in Europe, as demand grows because of the promotional activities of the European Union Commission as well as because of the oil’s good image.
Fig. 4.36. Main fatty acid composition of olive depending on the country of origin.
Fats and Oils Handbook
21 6 Olive oil T-(vp PPO
Pso ohur Po0
so0 PPca
dhn OOO pa. SOL pooo 0th.n OQ
RL POL. c4ml
OU OOL.
omrn opwr
-Iwm1
Fig. 4.37. Triglyceride composition of olive oil (after Descargues and Bezard 1981).
The amounts available differ greatly from year to year. In 1987/88, a record harvest delivered 1.9 MMT of oil, whereas a year later, the yield was only 1.6 MMT (Table 4.21). Estimates differ on how much of the crop is extracted for oil. Raina (1993) estimates 93%; other sources suggest 85%. The amount of oil is always -20% of the tonnage of harvested fruit. The Mediterranean countries continue to be the main source of olives. However, other countries have attempted to grow the fruit. Brazil’s first mentionable crop was in 1990, but still in negligible quantities. 4.2.2.4 Harvesting Olives and Oil Extraction. Olives should be harvested shortly before complete ripening, which is indicated by blackening of the fruit (Table 4.22). TABLE 4.21 Olive and Olive Oil Production as Well as Number of Trees (mil1ions)d
Total world, olives Italy Greece Spain Portugal Tunisia Total world, olive oil (MMT)
Trees
1935
1950
1960
1970
1980
1990
1994 1995
800 181 118 189 50 56
4.5 1.3 0.5 1.8 0.4
4.8 1.2 0.5 1.6 0.4
7.1 2.1 0.4 2.4 0.3
7.2 2.4 1.0 1.8 0.3
9.2 1.6 1.3 3.0 0.25 0.33
11.3 2.6 1.9
-
8.0 3.0 1.5 2.0 0.3 0.5
1.0
1.1
1.38
1.63
1.75
1.77
-
-
-
aApproximately90% used for Oil extraction; extraction oil equivalent -25%.
2.7 0.2 0.6 1.96
9.3 3.O 1.6 1.6 0.2 0.6 1.59 -
Vegetable Fats and Oils
217
TABLE 4.22 O l i v e Harvesting Periods
France Greece Italy Portugal Spain Turkey
Jan
Feb
Mar
H H
H
H
H
H
Apr
May
June July Aug
H H
Sept
H H H H
Oct Nov Dec H H H H H
H H H H H
H H
Traditionally, the three following methods are used: Brucatura, picking the olives from the tree; Raccattattura, collecting the fallen olives; and Scuotitura, shaking the tree (for example, mechanically) and collecting the fallen fruit. During harvesting, the olives are usually exposed to mechanical stress. This leads to damage of the cells and initiates fat spoilage. This holds especially true for the raccattattura olives because they fall from the tree when they are ripe and soft. They are easily damaged by the lightest pressure. This is the reason for the extraction of the oil immediately after harvest. Extraction is done mainly in small, decentralized mills. Today, mechanical picking is possible (Chabar and Zguial 1987). Figure 4.38 gives the flow chart for the production of olive oil.
4.2.2.5 Fact File of Olive Oil. This fact file shows the physical and chemical data of olive oil (Fig. 4.39 and Table 4.23). For olive oil, different traded qualities exist that allow very different pricing. Virgin olive oil is the highest quality with the following three grades: extra virgine @FA c l%),virgine (FFA c 1.5%) and semi-fine (FFA c 3%). The lowest edible quality grade is must oil. The oil called “lampante,” which is for industrial purposes, may have a higher FFA content (FFA c 3.3%). Virgin olive oil contains pigments that are left in the oil. Minguez-Mosquera et al. (1991) determined up to 54 ppm of the chlorophyll type and up to 22.5 ppm of the carotenoid type. In 1990, the price for virgin olive oil was -$5000/ton. Sources for more detailed information can be found in the references section. 4.2.3 Avocado Oil 4.2.3.1 Botany, Composition, and Properties of Avocado Oil. Avocado (Persea gratissima gaertueri) is a 12- to 15-m high evergreen tree that grows mainly in the Mediterranean region and in the Southern U.S. Although the kernel has an oil content of only 1-2%, the mesocarp of the avocado contains a substantial amount of oil, depending on the sort, i.e., normally 10-30% of the total fruit weight. In the edible part, Florida fruit commonly contain -40% oil; the Turkish avocado, however, can contain as much as 75% oil (Fig. 4.40). As in palm oil, -tic and oleic acid are the main fatty acids with oleic acid being dominant. Additionally, up to 2.2%myristic acid and 1% arachic acid are to be found (Fig. 4.41).
Fats and Oils Handbook
218
1-
< 40.C. for hqh amounb of virgin oil r n . p u W n of the oii in miiaxeun
i win
(MH a d b n i( needed)
last melueur, to make the pulp mon nuid
big decanten (continuously)
Olive oil
I Proportion[%I
Fstty add Palm& PlhitObic
Stesric oleic Linobic
Linobnic Arachic
c 180 C 16:l C 18:O C 18:l c 182 C 183 c 20:o
-
7.5 20.0 0.3 3.5 0.5 5.0 55.0 83.0 3.5 -21.0 < 1.5 < 0.0
Fig. 4.39. Fact file of olive oil (fatty acid composition).
219
Vegetable Fats and Oils
TABLE 4.23 Fact File of Virgin a n d Refined O l i v e Oil a n d O l i v e Pomace Oil German: Olivenol
French: huile d'olive
Relative density Refractive index Saponification value Iodine value p-Sisterol Unsaponifiable matter
(at 20°C; ref. water 20°C) (nD40) (mg KOH/g oil) W i j s method) (% of total sterols) (gkg oil)
Spanish: aceite de oliva 0.910-091 6 1.4677-1.4705 184-1 96 75-94 593 4 5
Solidification point
ooc
Melting point
-9 to 0°C
Solids content at
(OCPF)
0.32
514 1
10/50
20/68
30/86
35/95
(%)
<0.3
0
0
0
0
0
World market price (U.S. $/MT)
min
Price index for virgine 1995 average compared with 10 years ago 150% with20yearsago 180% with30yearsago 320%
1964-1 995 1964-1 969 1970-1979 1980-1989 199C-1995
Differences for olive pomace oil Refractive index Saponification value Iodine value Unsaponifiable matter
920 1073 920 2255 3235
Virgine 0 3900 1220 2055 3070 5145
--1
max
Lampante min 0 max
6950 1375 31 15 3965 6950
780 790 780 1885 2670
(nD40) (mg KOH/g oil) (Wijs method) (gMg oil)
2845 888 1565 2215 3725
3885 1095 2505 2910 3885
1.4680-1.4707 182-1 93 75-92 <30
Differentiation of virgin olive oil (V), refined olive oil (R) and refined olive pomace oil (P) Max satur.FA in 2-position
v R P
Max. acidity KOH/g oil
1 .5% 1.8% 2.2%
Definitions for olive oil
6.6 0.6 0.6
Peroxide value
Extinction 232 270
Volatile matters
Insoluble impurities
9 0 210%
3.5
-
50.2% 20.1'/0
-
6.0
50.10% 50.05% 20.05%
0.3 1.1 2.0
10.1%
trans fatty acidsa
alnternational Olive Oil Council Trade Standard (May 1992) limits for all olive oils as percentage of total sterols: cholesterol 50.5%; brassicasterol 50.1%; campesterol 54.0%. Olive oil (R) Nonextracted oil, non