Ultra-Wideband Radio Propagation Channels

Ultra-Wideband Radio Propagation Channels A Practical Approach

Pascal Pagani Friedman Tchoffo Talom Patrice Pajusco Bernard Uguen Series Editor Pierre-Noël Favennec

This page intentionally left blank

Ultra-Wideband Radio Propagation Channels

This page intentionally left blank

Ultra-Wideband Radio Propagation Channels A Practical Approach

Pascal Pagani Friedman Tchoffo Talom Patrice Pajusco Bernard Uguen Series Editor Pierre-Noël Favennec

First published in France in 2007 by Hermes Science/Lavoisier entitled: “Communications ultra large bande : Le canal de propagation radioélectrique” First published in Great Britain and the United States in 2008 by ISTE Ltd and John Wiley & Sons, Inc. Apart from any fair dealing for the purposes of research or private study, or criticism or review, as permitted under the Copyright, Designs and Patents Act 1988, this publication may only be reproduced, stored or transmitted, in any form or by any means, with the prior permission in writing of the publishers, or in the case of reprographic reproduction in accordance with the terms and licenses issued by the CLA. Enquiries concerning reproduction outside these terms should be sent to the publishers at the undermentioned address: ISTE Ltd 27-37 St George’s Road London SW19 4EU UK

John Wiley & Sons, Inc. 111 River Street Hoboken, NJ 07030 USA

www.iste.co.uk

www.wiley.com

© ISTE Ltd, 2008 © LAVOISIER, 2007 The rights of Pascal Pagani, Friedman Tchoffo Talom, Patrice Pajusco and Bernard Uguen to be identified as the authors of this work have been asserted by them in accordance with the Copyright, Designs and Patents Act 1988. Library of Congress Cataloging-in-Publication Data Communications ultra large bande. English Ultra-wideband radio propagation channels / Pascal Pagani ... [et al.]. p. cm. -- (A practical approach) Includes bibliographical references and index. ISBN 978-1-84821-084-4 1. Broadband communication systems. I. Pagani, Pascal. II. Title. TK5103.4.C6213 2008 621.382--dc22 2008030345 British Library Cataloguing-in-Publication Data A CIP record for this book is available from the British Library ISBN: 978-1-84821-084-4 Cover image created by Atelier Isatis, based on an original photograph by Denis Stenderchuck. Printed and bound in Great Britain by CPI Antony Rowe Ltd, Chippenham, Wiltshire.

Contents

Foreword

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

Acronyms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

Chapter 1. UWB Technology and its Applications . . . . . . . . . . . . .

21

1.1. Introduction . . . . . . . . . . . . . . . . . . . . . . 1.2. Definition and historical evolution . . . . . . . . . 1.2.1. Definition . . . . . . . . . . . . . . . . . . . . . 1.2.2. Historical evolution . . . . . . . . . . . . . . . 1.3. Specificities of UWB . . . . . . . . . . . . . . . . . 1.4. Considered applications . . . . . . . . . . . . . . . . 1.5. Regulation evolution . . . . . . . . . . . . . . . . . 1.5.1. Regulation in the USA . . . . . . . . . . . . . 1.5.2. Regulation in Europe . . . . . . . . . . . . . . 1.5.3. Regulation in Asia . . . . . . . . . . . . . . . . 1.6. UWB communication system and standardization 1.6.1. Impulse radio . . . . . . . . . . . . . . . . . . . 1.6.1.1. Pulse position modulation . . . . . . . . 1.6.1.2. Pulse amplitude modulation . . . . . . . 1.6.2. Direct sequence UWB . . . . . . . . . . . . . 1.6.3. Multiband OFDM . . . . . . . . . . . . . . . . 1.7. Conclusion . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . .

21 22 22 23 24 26 30 31 32 33 34 35 35 38 39 40 41

Chapter 2. Radio Wave Propagation . . . . . . . . . . . . . . . . . . . . .

43

2.1. Introduction . . . . . . . . . . . . . . . 2.2. Definition of the propagation channel 2.2.1. Free space propagation . . . . . . 2.2.2. Multipath propagation . . . . . . 2.2.3. Propagation channel variations .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . . . . . . . . . . . . . .

. . . . .

. . . . .

43 43 44 45 47

6

Ultra-Wideband Radio Propagation Channels

2.2.3.1. Spatial selectivity . . . . . . . . . . . . . . . . . . . . . . 2.2.3.2. Frequency selectivity . . . . . . . . . . . . . . . . . . . . 2.2.3.3. Doppler effect . . . . . . . . . . . . . . . . . . . . . . . . 2.3. Propagation channel representation . . . . . . . . . . . . . . . . . 2.3.1. Mathematical formulation . . . . . . . . . . . . . . . . . . . . 2.3.2. Characterization of deterministic channels . . . . . . . . . . 2.3.2.1. The time varying impulse response . . . . . . . . . . . . 2.3.2.2. The frequency domain function . . . . . . . . . . . . . . 2.3.2.3. The time varying transfer function . . . . . . . . . . . . 2.3.2.4. The delay-Doppler spread function . . . . . . . . . . . . 2.3.3. Characterization of linear random channels . . . . . . . . . . 2.3.4. Channel classification . . . . . . . . . . . . . . . . . . . . . . . 2.3.4.1. Wide sense stationary channels . . . . . . . . . . . . . . 2.3.4.2. Uncorrelated scattering channels . . . . . . . . . . . . . 2.3.4.3. Wide sense stationary uncorrelated scattering channels 2.4. Channel characteristic parameters . . . . . . . . . . . . . . . . . . 2.4.1. Frequency selectivity . . . . . . . . . . . . . . . . . . . . . . . 2.4.1.1. RMS delay spread . . . . . . . . . . . . . . . . . . . . . . 2.4.1.2. Coherence bandwidth . . . . . . . . . . . . . . . . . . . . 2.4.1.3. Delay window and delay interval . . . . . . . . . . . . . 2.4.1.4. Exponential decay constants . . . . . . . . . . . . . . . . 2.4.1.5. Cluster and ray arrival rates . . . . . . . . . . . . . . . . 2.4.2. Propagation loss . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.3. Fast fading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.4. Spectral analysis . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5. Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

48 48 50 51 51 52 53 53 54 54 54 55 55 56 57 58 58 59 59 60 61 61 62 63 64 64

Chapter 3. UWB Propagation Channel Sounding . . . . . . . . . . . . .

67

3.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2. Specificity of UWB channel sounding . . . . . . . . . . . . . . . 3.3. Measurement techniques for UWB channel sounding . . . . . . 3.3.1. Frequency domain techniques . . . . . . . . . . . . . . . . . 3.3.1.1. Vector network analyzer . . . . . . . . . . . . . . . . . 3.3.1.2. Chirp sounder . . . . . . . . . . . . . . . . . . . . . . . 3.3.2. Time domain techniques . . . . . . . . . . . . . . . . . . . . 3.3.2.1. Pulsed techniques . . . . . . . . . . . . . . . . . . . . . 3.3.2.2. Correlation measurements . . . . . . . . . . . . . . . . 3.3.2.3. Inversion techniques . . . . . . . . . . . . . . . . . . . . 3.3.3. Multiple-band time domain sounder for dynamic channels 3.3.3.1. Principle of multiple-band time domain sounding . . 3.3.3.2. Description of the SIMO channel sounder . . . . . . . 3.3.3.3. Extension towards UWB . . . . . . . . . . . . . . . . . 3.3.3.4. Experimental validation . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . .

67 67 70 71 71 72 73 73 75 78 78 80 81 81 84

Contents

3.4. UWB measurement campaigns . . . . . . . . . . . . . . . . . . . . 3.4.1. Overview of UWB measurement campaigns . . . . . . . . . . 3.4.2. Illustration of channel sounding experiments . . . . . . . . . 3.4.2.1. Static measurement campaign over the 3.1–10.6 GHz band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4.2.2. Static measurement campaign over the 2–6 GHz band 3.4.2.3. Dynamic measurement campaign over the 4–5 GHz band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5. Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 4. Deterministic Modeling of the UWB Channel

7

85 85 91 91 95 95 98

. . . . . . . .

99

4.1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2. Overview of deterministic modeling . . . . . . . . . . . . . . . . . 4.2.1. FDTD based approach . . . . . . . . . . . . . . . . . . . . . . 4.2.2. MoM based approach . . . . . . . . . . . . . . . . . . . . . . . 4.2.3. Ray based approach . . . . . . . . . . . . . . . . . . . . . . . . 4.3. Specificity of deterministic modeling in UWB . . . . . . . . . . . 4.4. Overview of UWB deterministic modeling . . . . . . . . . . . . . 4.4.1. Qiu model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.2. Yao model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.3. Attiya model . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.4. Uguen and Tchoffo Talom model . . . . . . . . . . . . . . . . 4.5. Illustration of a deterministic model formalism . . . . . . . . . . . 4.5.1. Received signal synthesis . . . . . . . . . . . . . . . . . . . . . 4.5.2. Ray impulse response without delay . . . . . . . . . . . . . . 4.5.3. Ray channel matrix without delay . . . . . . . . . . . . . . . 4.5.4. Described model results . . . . . . . . . . . . . . . . . . . . . 4.5.4.1. Emitted waveform and considered scenario . . . . . . . 4.5.4.2. Channel matrix of each emitted waveform in the LOS case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5.4.3. Received signal with ideal antennas . . . . . . . . . . . 4.6. Consideration of real antenna characteristics in deterministic modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7. Building material effects on channel properties . . . . . . . . . . . 4.8. Simulation and measurement comparisons . . . . . . . . . . . . . 4.8.1. Evaluation of real antenna consideration . . . . . . . . . . . 4.8.2. Evaluation of impulse response reconstruction . . . . . . . . 4.9. Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

99 99 100 100 101 101 102 102 102 103 104 104 105 105 108 110 110

Chapter 5. Statistical Modeling of the UWB Channel

113 114 118 120 124 124 125 126

. . . . . . . . . .

133

5.1. Experimental characterization of channel parameters . . . . . . . 5.1.1. Propagation loss . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.1.1. Frequency propagation loss . . . . . . . . . . . . . . . .

134 134 134

8

Ultra-Wideband Radio Propagation Channels

5.1.1.2. Distance propagation loss . . . . . . . . . . . . . . . . . 5.1.2. Impulse response characterization . . . . . . . . . . . . . . . 5.1.2.1. Delay spread . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.2.2. Power delay profile decay . . . . . . . . . . . . . . . . . 5.1.2.3. Ray and cluster arrival rate . . . . . . . . . . . . . . . . 5.1.3. Study of small-scale channel variations . . . . . . . . . . . . 5.1.4. Effect of moving people . . . . . . . . . . . . . . . . . . . . . . 5.1.4.1. Observation of temporal variations . . . . . . . . . . . . 5.1.4.2. Slow fading . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.4.3. Fast fading . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.4.4. Spectral analysis . . . . . . . . . . . . . . . . . . . . . . . 5.2. Statistical channel modeling . . . . . . . . . . . . . . . . . . . . . . 5.2.1. Examples of statistical models . . . . . . . . . . . . . . . . . 5.2.1.1. IEEE 802.15.3a model . . . . . . . . . . . . . . . . . . . 5.2.1.2. IEEE 802.15.4a model . . . . . . . . . . . . . . . . . . . 5.2.1.3. Other models . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2. Empirical modeling principles . . . . . . . . . . . . . . . . . . 5.2.2.1. Propagation loss model . . . . . . . . . . . . . . . . . . . 5.2.2.2. Modeling the channel impulse response over an infinite bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2.3. Modeling the channel impulse response over a limited bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2.2.4. Simulation results . . . . . . . . . . . . . . . . . . . . . . 5.3. Advanced modeling in a dynamic configuration . . . . . . . . . . 5.3.1. Space variation modeling . . . . . . . . . . . . . . . . . . . . . 5.3.2. Modeling the effect of people . . . . . . . . . . . . . . . . . . 5.4. Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

136 137 137 141 145 148 151 151 152 153 156 157 158 158 159 160 162 162 163 166 166 169 169 172 175

Appendices A. Baseband Representation of the Radio Channel . . . . B. Statistical Distributions . . . . . . . . . . . . . . . . . . B.1. Definition . . . . . . . . . . . . . . . . . . . . . . . . B.1.1. Rayleigh distribution . . . . . . . . . . . . . . B.1.2. Rice distribution . . . . . . . . . . . . . . . . B.1.3. Nakagami distribution . . . . . . . . . . . . . B.1.4. Weibull distribution . . . . . . . . . . . . . . B.1.5. Normal distribution . . . . . . . . . . . . . . . B.1.6. Log-normal distribution . . . . . . . . . . . . B.1.7. Laplace distribution . . . . . . . . . . . . . . B.2. Kolmogorov-Smirnov goodness-of-fit test . . . . . C. Geometric Optics and Uniform Theory of Diffraction . C.1. Geometric optics . . . . . . . . . . . . . . . . . . . C.1.1. Introduction . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

. . . . . . . . . . . . . .

177 181 181 181 182 183 184 184 185 185 186 189 189 189

Contents

C.1.2. Field locality principle . . . . . . . . C.1.3. Field expression in geometric optics C.1.4. Change of local basis . . . . . . . . . C.1.5. Incident field . . . . . . . . . . . . . . C.1.6. Reflected field . . . . . . . . . . . . . C.1.7. Refracted and transmitted field . . . C.2. Uniform theory of diffraction . . . . . . . C.2.1. Introduction . . . . . . . . . . . . . . C.2.2. Diffracted field . . . . . . . . . . . . . C.2.3. UTD 2D coefficient . . . . . . . . . . C.2.4. UTD 3D coefficient . . . . . . . . . . D. Ray Construction Techniques . . . . . . . . . . D.1. Ray launching . . . . . . . . . . . . . . . . D.2. Ray tracing . . . . . . . . . . . . . . . . . D.3. Other techniques . . . . . . . . . . . . . . E. Description of the Time-Frequency Transform

. . . . . . . . . . . . . . . .

190 191 192 192 193 197 200 200 200 201 204 209 209 209 211 213

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

219

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

237

Bibliography

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . .

9

This page intentionally left blank

Foreword

Although the origins of distant signal transmission are ancient, the theoretical foundations of modern telecommunication techniques are owed to Claude Shannon’s 1948 publications. Since then, the field of telecommunications has not stopped evolving. In particular, spread spectrum techniques enabled unprecedented improvements in the quality and security of digital communications under harsh transmission conditions. Today, the main players in the telecommunication world are facing an increasing demand for multimedia wireless applications, linked to a real need for very high throughput radio communication systems. Among the most recent innovations in this field, the scientific community is particularly interested in ultra-wideband (UWB) technology. This technique consists of transmitting radio signals spreading over very large frequency bandwidths, typically in the order of 500 MHz to several GHz. Initially developed in the field of radar localization, UWB technology is now seen as a promising candidate for future wireless transmission systems. As such, it is considered with an increasing interest in both scientific and industrial communities. UWB technology undeniably offers numerous advantages and unprecedented possibilities in the design of radio systems. Its very large spectral bandwidth optimally exploits the benefits of spread spectrum techniques, by increasing the transmission capacity and by improving the jamming immunity. Simultaneously, UWB presents a high resolution in the time domain, which may be used to efficiently process the multiple propagation paths or handle localization issues. In particular, the capacity of UWB pulses to travel through different materials allows us to consider through-wall imaging applications. It is also noteworthy that UWB systems present a low power spectral density, which not only increases the discretion and security of wireless communications, but also reduces the potential jamming experienced by other spectrum users. Finally, the complexity of

12

Ultra-Wideband Radio Propagation Channels

UWB transceivers may be considerably reduced with respect to traditional architectures. These characteristics are unique to UWB technology and enable the design of communication systems offering very high data rates, up to several hundred Mbps. In 2002, the Federal Communication Commission (FCC) – an American regulation body – authorized the transmission of UWB signals in the 3.1–10.6 GHz band, encouraging the research efforts in this field in all continents. In Europe, a transmission mask for UWB signals has been defined and the coexistence between UWB systems and other applications is under study. In the current context of high demand for wireless multimedia applications, UWB seems to be an innovative and attractive solution for future radio communication systems. As an illustration, important industrial consortiums such as UWB Forum and WiMedia Alliance are currently involved in the design of UWB based equipment. These systems are particulary well suited to ad hoc communication networks, but a number of other applications may be envisioned by exploiting the unique characteristics of UWB. The possibility of accurate localization enable the development of sensor networks known as radio frequency identification (RFID), for industrial environment applications or for mass market geographical information services. Radar identification techniques based on UWB signals may be exploited to design anti-collision systems for vehicles, but may also be used in the fields of civil engineering, medicine and imaging. Numerous applications still need to be explored, associating UWB with advanced techniques such as multiple-input multiple-output (MIMO) antennas techniques or time reversal techniques. In order to develop such systems, many challenges are still to be encountered. The short duration of UWB signals requires a high accuracy in the system synchronization procedure. Also, electronic components need to be adapted in order to process such a wide frequency band, while maintaining a tractable complexity. In particular, the antenna characteristics largely vary with increasing frequency and require an accurate characterization. Among these scientific challenges, a complete knowledge of the radio channel properties is fundamental. Indeed, the performance of a wireless transmission system is directly linked to the propagation conditions between the emitter and the receiver. These devices need to be designed in order to benefit from the channel characteristics and to mitigate the channel impairments. For instance, modeling the propagation loss allows us to estimate the radio system coverage, while link level simulations may be used to assess the communication robustness. Owing to the width of its frequency band, the

Foreword

13

UWB propagation channel is intrinsically different from traditional wideband channels. For instance, the interactions between the radio waves and their environment need to be described more accurately and the variations of the material properties with frequency need to be taken into account. It is thus necessary to closely study the propagation channel in order to evaluate the potential and the constraints attached to UWB communication systems. This textbook results from an intense collaboration between France Telecom’s Research and Development Division and the IETR–UMR CNRS 6164 (Institut d’Electronique et de T´el´ecommunications de Rennes/Institute of Electronics and Telecommunications in Rennes). These research teams conducted joint studies on UWB techniques and on the impact of the transmission channel on UWB communication systems. Through its didactic presentation and the detailed illustration of the discussed topics, this document is an excellent introduction for engineers and communication systems designers as well as for researchers and lecturers willing to expand their knowledge to the field of the UWB transmission channel. The originality of this textbook lies in its experimental approach, which allows the reader to follow step by step the theoretical and practical aspects of radio channel characterization and modeling. This approach may easily be adapted to different contexts: for different applications, in other environments or in different frequency bands, such as the available bands around 17 GHz and 60 GHz. It should also be noted that the accurate knowledge of the UWB channel in the 3.1–10.6 GHz band gives access to all the useful information for developing systems included in this frequency band, such as WiFi systems operating around 5 GHz. This book is divided into five distinct parts. Chapter 1 presents UWB technology. Its historical evolution, the envisioned applications and its main characteristics are detailed. UWB spectrum regulation issues and the proposed communications techniques are also discussed. Chapter 2 describes the propagation of electromagnetic waves in general. All large scale and small scale radioelectric phenomena at play are highlighted. The reader is then introduced to the area of mathematical representation and its characteristic parameters. This didactic presentation covers both indoor and outdoor environments and is applicable in both contexts of mobile radio and wireless networks. Chapter 3 presents an overview of the channel sounding techniques adapted to UWB technology. A distinction is made between frequency domain and time domain techniques, with a discussion on the application domains and the

14

Ultra-Wideband Radio Propagation Channels

limitation of each solution. The main UWB channel measurement campaigns available in the literature, including those conducted by the authors, are listed and illustrated by a few examples. For the study of the propagation phenomena and the design of communication systems, the UWB propagation channel is simulated using deterministic or statistical models. These two modeling approaches are detailed and illustrated in the last two chapters. Chapter 4 focuses on deterministic UWB modeling. A literature review of the proposed deterministic models is given, comparing the advantages and drawbacks of each proposal. The fundamental issues and the theoretical formalism of a UWB deterministic model are then detailed. To illustrate this presentation, some examples are given, where the authors describe a comprehensive deterministic simulator for the UWB channel. Chapter 5 is dedicated to the statistical modeling of the UWB transmission channel. The characterization of the most representative radio channel parameters is first presented. Different results available in the literature are compared and commented upon, hence providing a rich experimental database on the UWB propagation channel characteristics. After a description of different statistical models, the principles of statistical modeling and the different related issues are presented following an experimental method. This approach is illustrated using a model designed by the authors, allowing for the simulation of the UWB channel in both static and dynamic environments. Finally, the interested reader will find useful additional information regarding channel analysis and modeling in the appendices. The discussed technical material includes the fields of signal processing, statistics, geometrical optics and diffraction theory. It should also be noted that the numerous bibliographical references constitute an abundant source of information, which may easily be exploited to learn more about the last advances in this field. This book examines all the characteristics of the UWB transmission channel and provides useful tools for designing efficient UWB systems. Non-specialists will be introduced to UWB technology in general and more particularly to the propagation channel, which is the key element in a communication system. Specialists will find valuable information and a practical approach in order to design simulators, set-up measurements, study the channel characteristics and define models for UWB or in other contexts. This reference document is also an excellent basis for further research on advanced techniques, such as time reversal or UWB transmission in a MIMO

Foreword

15

configuration. I am convinced that this textbook will prove essential reading in future research in the field of UWB communications. Professor Gha¨ıs El Zein Deputy Director at IETR

This page intentionally left blank

Acronyms

ADC AGC BER BPSK CDF CDMA CEPT DAA DAC DCS DOA DOD DSO DS-UWB ECC EIRP ESD ETSI FCC FDML FDTD GO GPS GSM GTD IDA IEEE IF IMST

Analog-to-digital converter Automatic gain control Bit error rate Binary phase shift keying Cumulative density function Code division multiple access Conference of European Postal and Telecommunications Detect and avoid Digital-to-analog converter Digital communication system Direction of arrival Direction of departure Digital sampling oscilloscope Direct sequence ultra-wideband Electronic Communication Committee Effective isotropic radiated power Energy spectral density European Telecommunications Standards Institute Federal Communication Commission Frequency domain maximum likelihood Finite difference time domain Geometrical optics Global positioning system Global system for mobiles Geometrical theory of diffraction Infocom Development Authority of Singapore Institute of Electrical and Electronics Engineers Intermediate frequency Institut f¨ ur Mobil- und Satellitenfunktechnik

18

Ultra-Wideband Radio Propagation Channels

IR ISB ISM ITU LDC LNA LO LOS MB-OFDM MIC MIMO MoM NLOS OFDM OOK PAM PDA PDF PDP PLL PN PPM PSD QAM QPSK RF RFID RIR RSB SAGE SHF SIMO SISO SWR UHF UMTS UNII US UTD UWB VCO VNA WBAN

Impulse response Incident shadow boundary Industrial, scientific and medical International telecommunication union Low duty cycle Low noise amplifier Local oscillator Line of sight Multiband orthogonal frequency division mutliplexing Ministry of Internal Affairs and Communications Multiple-input multiple-output Method of moments Non-line of sight Orthogonal frequency division mutliplexing On-off keying Pulse amplitude modulation Personal digital assistant Probability density function Power delay profile Phase locked loop Pseudo-noise Pulse position modulation Power spectral density Quadrature amplitude modulation Quadrature phase shift keying Radio frequency Radio frequency identification Ray impulse response Reflection shadow boundary Space alternating generalized expectation Super high frequencies Single-input multiple-output Single-input single-output Standing wave ratio Ultra high frequencies Universal mobile telecommunications system Unlicensed national information infrastructure Uncorrelated scattering Uniform theory of diffraction Ultra-wideband Voltage control oscillator Vector network analyzer Wireless body area network

Acronyms

WiFi WLAN WPAN WSS WSSUS 802.11 802.15.3 802.15.4

Wireless fidelity Wireless local area network Wireless personal area network Wide-sense stationary Wide-sense stationary uncorrelated scattering IEEE task group on WLAN IEEE task group on high rate WPAN IEEE task group on low rate WPAN

19

This page intentionally left blank

Chapter 1

UWB Technology and its Applications

1.1. Introduction

By the end of the 20th century, studies in the telecommunication field had made significant progress. The advent of new radiocommunication technologies allowed telephony to change from a telegraphic transmission support to a radio transmission support. Over the last few years, the processing speed and storage size of the computers have increased considerably. This explains the general public’s passion for communicating objects, which require the high speed transfer of a great amount of information.

One of the current scientific challenges, where significant research efforts are engaged, is related to the use of very high data rate radio transmissions techniques on relatively short ranges. In this context, ultra-wideband (UWB) technology, initially used in radar, appears to be an ideal candidate for future wireless communication systems.

This chapter presents the UWB technology and its applications for wireless communication systems. After a definition of UWB and of its historical evolution, its characteristics are first outlined, then the considered applications and the regulation spectrum in the USA, Asia and Europe are detailed. The chapter ends by presenting the modulation techniques proposed for UWB and by a state of the art of standardization today.

22

Ultra-Wideband Radio Propagation Channels

1.2. Definition and historical evolution 1.2.1. Definition The generic term UWB is used to represent a radio technique which was studied under various names. In the earliest writings on this field, we can find the terms impulse radio, carrier-free radio, baseband radio, time domain radio, non-sinusoid radio, orthogonal function radio and large relative bandwidth radio [BAR 00]. The relative bandwidth is defined by: Bf,3 dB = 2 ·

fH − fL fH + fL

[1.1]

where fH and fL respectively represent the upper and lower cut-off frequencies of the band defined at −3 dB. Initially, UWB signals were defined by a relative bandwidth of 25% or more [TAY 95]. In 2002, the American regulation authority, the Federal Communication Commission (FCC), extended this definition to a broader category of signals, by including signals with a relative bandwidth Bf,10 dB higher than 20% or with a frequency band higher than 500 MHz [FCC 02]. Typically, the bandwidth of UWB signals is about 500 MHz to several GHz. Thus, the denomination UWB not only includes impulse techniques, but also all the modulations presenting an instantaneous band higher than or equal to 500 MHz. GHz

Power spectral density (dBm.MHz -1)

MHz Conventional narrowband modulation

kHz

Spread spectrum Ultra-wideband

-41.3 dB m.MHz -1

Bandwidth (Hz) Figure 1.1. Comparison of various radio system spectrums

Figure 1.1 illustrates the comparison between conventional radio systems, which generally modulate a narrowband signal on a carrier frequency, wideband

UWB Technology and its Applications

23

systems, with spreading spectrum for example, and ultra-wideband systems, which show a weak power spectral density. As a comparison, the bandwidth of UMTS signals is 5 MHz.

1.2.2. Historical evolution The study of electromagnetism in the time domain began 40 years ago. The first research was concentrated on radar applications because of the broadband nature of the signals, which implies a strong resolution1 in the time domain. It was in 1960 that impulse radars were developed by the American and Soviet armies. Indeed, impulse systems have good space resolution properties. The resolution in distance of a system is conversely proportional to its bandwidth; the brevity of an impulse signal determines its spectrum width. In the 1970s, Bennett and Ross presented a complete study of the first research carried out on UWB [BEN 78]. Two decades later, Taylor described the bases of the UWB technology applied to radar [TAY 95]. Since the middle of the 1960s, research on this field regularly progressed, as mentioned in the historical bibliography published by Barrett [BAR 00]. However, the use of UWB signals for radio communication was not really considered before the end of the 20th century. In 1990, the Department of Defense of the US government published the results of its evaluation of UWB technology. These results were mainly concentrated on radar systems, since no application of UWB technology to communication systems was considered at that point [FOW 90]. More recently, research focused on UWB signals for radio communication [SCH 93, SCH 97a], by using the main characteristics of this technique: a time resolution around one nanosecond due to the huge frequency bandwidth, a short duty cycle allowing for modulations such as time hopping and the management of multi-users, as well as a possible transmission without carrier, which can lead to a simplification of the radio system architecture [FOE 01a]. In 1998, the FCC launched the first study on UWB. In February 2002, a first regulatory report was published, allowing particularly for the transmission of signals in the 3.1–10.6 GHz band for wireless communications, with strong constraints on the power spectral density [FCC 02]. From this date, intensive academic and industrial research was undertaken with the aim of proposing a powerful communication systems using UWB technology.

1. The resolution of a system is its capacity to separate very close energy paths.

24

Ultra-Wideband Radio Propagation Channels

1.3. Specificities of UWB With the need for increasing the data rate of wireless systems, the UWB technology seems to be an ideal candidate for future radio communication systems in various types of networks, which can be residential, office, ad hoc, etc. As shown in section 1.2.1, the main characteristic of the UWB signal is the width of the occupied frequency band, typically about 500 MHz to several GHz. Information theory teaches us that with the use of an appropriate code, it is possible to transmit data with a binary error rate (BER) lower than a fixed arbitrarily low threshold, that is, if the data rate is lower than the theoretical value of the transmission channel capacity. Thus, channel capacity C gives an indication of the theoretical maximum data rate reachable with a given channel. It can be obtained using Shannon’s theorem [SHA 49]:   S [1.2] C = Bw · log2 1 + N where C is the channel capacity (bit/s), Bw is the signal bandwidth (Hz), S is the signal power level (W) and N is the noise power level (W). We can note that for a given bandwidth the channel capacity increases in a logarithmic way with the signal to noise ratio. In the case of a constant signal to noise ratio, the capacity increases linearly with the signal bandwidth.2 In the context of an increasing demand for communication systems with high data rates, radio technologies using a broad spectral band are more able to propose convenient data rates. So, with a frequency band reaching several GHz, the UWB is well adapted to an increase of data rate than the systems showing a high constraint on the bandwidth [FOE 01a]. The main properties of UWB systems are described below: • High temporal resolution capability Because of their great bandwidth, UWB signals have a high temporal resolution, typically about one nanosecond. A first implication of this property is related to the localization: knowing the delay of a signal with

2. We can note that for a given signal power level S, the capacity increases nonlinearly with the bandwidth and reaches the asymptotic value of Clim = NS0 · log2 (e), where N0 is the noise power spectral density.

UWB Technology and its Applications

25

a precision of about 0.1 to 1 ns, it is possible to obtain information on the position of the transmitter with an accuracy of 3 to 30 cm. • Robustness against fading related to multipath propagation In usual propagation channels, narrowband systems suffer from fading related to the multipath which combine in a destructive way. In the case of impulse signals, the transmitted waveforms can have a great bandwidth, so the multipath presenting delays lower than one nanosecond can be resolved and added in a constructive way. This recombination causes some complications on the system implementation, as it leads to the design of a receiver with a great number of diversity branches. • Low power spectral density This characteristic is not intrinsic to UWB signals as they were defined (see equation [1.1]), but it is imposed by the radio spectrum regulation authorities. Indeed, as UWB signals present a wide spread spectrum, the occupied frequency band necessarily covers the frequencies already allocated to existing radio systems. To allow a peaceful coexistence of UWB with existing narrowband radio technologies, the FCC has limited the power spectral density of UWB signals to −41.3 dBm.MHz−1 , which corresponds to the power spectral density limit of authorized non-intentional radio transmissions.3 This low power spectral density improves the safety of UWB radio communications, since it becomes more difficult to detect the transmitted signals. Another consequence of this characteristic concerns the propagation distance, which is thus limited to about ten meters. So, the applications considered for UWB systems are short range and high data rate, and are particularly adapted to the development of ad hoc networks. • Less sensitivity to jamming UWB systems offer a great processing gain.4 Thus, the interference UWB systems may have on other systems is reduced, thanks to the low level of the power spectral density authorized by the FCC. On the contrary, the interference caused by narrowband systems on UWB systems is a priori minimized by the bandwidth covered by the impulse signals.

3. Thus, we can consider that UWB radio signals are transmitted “under the noise level”, although the imposed limits remain above the thermal noise. 4. The processing gain of a system is a parameter which gives an indication of the resistance of this system against the jamming caused by the other systems.

26

Ultra-Wideband Radio Propagation Channels

• Protected and secured communications UWB signals are signals that are by nature difficult to detect. Indeed, they are spread over a broad band and transmitted with a low power spectral density close to the noise floor level of traditional radiocommunication receivers. These characteristics enable secured transmissions with a weak probability of detection and a weak probability of interception. • Relative simplicity of the systems design In terms of implementation, the conventional radio systems are generally of heterodyne design: the signal which codes the transmitted data is generated in baseband and is then transposed to higher frequencies before being emitted. The UWB technology allows the use of impulse generated in baseband and directly transmitted on the radio channel without modulation. This possibility of transmission without carrier may simplify the architecture of the radio systems. Indeed, it is possible to design UWB transmitter-receivers without any synthesizer using a phase locked loop (PLL), any voltage control oscillator (VCO) or any mixer. Thus, this can lead to the design of systems with low manufacturing and marketing costs. • Good obstacle penetration properties UWB signals offer good capabilities of penetration in the walls and the obstacles, in particular for the low frequencies part of the spectrum. This makes it possible to have a good precision in terms of localization and tracking [DEN 03b]. The American company Time Domain, pioneer in the topic of UWB for communication, has developed a broad activity around radar systems of vision through walls. 1.4. Considered applications For a few years, the world of telecommunications has faced an increasing demand for wireless numerical applications, in the industrial environment as well as from the general public. Moreover, we can add to this tendency an important need for total connectivity, the information having to be available for anybody, anywhere and at any time [POR 03b]. This increasing need for wireless connectivity leads to the development of many standards for wireless and short range communication systems. We can mention Bluetooth, the WiFi standards family (IEEE 802.11 a, b and g), Zigbee (IEEE 802.15.4) and the recent standard 802.15.3. We may note that the majority of these technologies for wireless local area networks (WLAN) and personal area networks (WPAN) uses free frequencies in ISM and UNII bands, with a maximum bandwidths of about 10 MHz. A comparative study of the characteristics of some wireless technologies is presented in Table 1.1. Taking into consideration other wireless systems like

UWB Technology and its Applications

27

Bluetooth or WiFi, the UWB technology presents a very low level of emission. However, we can reach transmission data rates that are definitely higher than the two other technologies. Figure 1.2 shows the position of UWB in comparison with the leading WLAN and WPAN standards in terms of rate and maximum achievable ranges. We can note that contrarily to WiFi standards, UWB technology mainly addresses short range WPAN networks. However, its potential data rate exceeds the performances of all current WLAN and WPAN standards.

Maximum bit rate (Mbps)

1000 UWB 100 802.15.3

WiFi 802.11g

WiFi 802.11a

WiFi 802.11b

10

1

Bluetooth

802.15.4a (Low rate UWB)

Zigbee

0.1 10

20

30

40

50

100

Maximum indoor range (m)

Figure 1.2. WLAN and WPAN main standards: rate and maximum ranges

In order to provide a high data rate anywhere, the future networks will have to be designed considering an optimization of the space capacity, namely the global available data rate per unit of area. In narrow band, we generally regard the spectral capacity of the systems in (bps/Hz) as one of the main parameters for a transmission. The various elements of a communication system, like the modulation, the coding, the implementation, etc. make it possible to improve it. By increasing only the transmission power or the signal band, the capacity also increases. However, the spectral resource for these systems is limited and their power cannot be increased indefinitely. It is limited by medical or commercial considerations, for example the pollution of the spectrum or the life duration of the batteries. For UWB systems, the transmission level or the transmitted power spectral density must be kept sufficiently low because these systems operate in already

3.1–10.6 GHz 3.1–10.6 GHz ISM 2.4 GHz 5 GHz ISM 2.4 GHz ISM 2.4 GHz

≥ 100 Mbps

≥ 500 kbps

≤ 700 kbps

≤ 54 Mbps

≤ 11 Mbps

≤ 54 Mbps

UWB

Bluetooth

WiFi

Modulation

0.1–1 W

0.1–2 W

0.2–1 W

type 1: 20 dBm type 2: 0 dBm

BPSK, 16-QAM, QPSK, 64-QAM, OFDM

CCK, BPSQ, QPSK, DSS

BPSK, 16-QAM, QPSK, 64-QAM

GMSK

−41.3 dBm/MHz PPM, OFDM, CDMA, . . .

−41.3 dBm/MHz PPM, OFDM, CDMA, . . .

EIRP

Table 1.1. Comparison of some wireless communication technologies

Frequency band

Data rate

Technology

IEEE 802.11g

IEEE 802.11b

IEEE 802.11a

IEEE 802.15.1

IEEE 802.15.4a

IEEE 802.15.3a

Specification

28 Ultra-Wideband Radio Propagation Channels

UWB Technology and its Applications

29

occupied bands. These low levels are compensated by the use of a broad band. So, compared to the existing wireless systems (see Table 1.2), UWB technology has a low spectral capacity. Thus, it is more correct to speak about the spatial capacity [GHA 04b]. This parameter corresponds to the maximum data rate of a system divided by the surface covered by this system. Rate

Distance

Spatial

Spectral

capacity

capacity

2

(Mbps)

(m)

(kbps/m ) (bps/Hz)

UWB

100

10

318.3

IEEE 802.11a

54

50

6.9

2.7

Bluetooth

1

10

3.2

0.012

IEEE 802.11b

11

100

0.350

0.1317

0.013

Table 1.2. Comparison of the spatial and spectral capacity of some wireless systems

Wireless and very high data rate radio technologies like UWB will make it possible to considerably increase the spatial capacity, by the development of dynamic ad hoc networks [POR 03b]. Finally, we can note that a standardization work is currently in progress in the IEEE 802.15.4a work group to use UWB spectrum within the framework of low data rate and short range radio links. The expected data rate is typically the same as that of the Zigbee standard, with a range of about a hundred meters. Thus, the potential applications of UWB radio technology are mainly related to two techniques: high data rate for short range systems (typically 200 Mbps up to 10 m), and low data rate for long range systems (typically 200 kbps at 100 m). These two ways of using the UWB radio spectrum allow us to consider a given number of typical applications for UWB systems [YAN 04, POR 03b]. Firstly, UWB technology will make it possible to increase the data rate of traditional personal wireless networks. So, it will be useful for WiFi networks which make wireless access to the Internet network possible, or for connections between various peripherals (printer, readers, etc.) in limited size environments of, for example, one or more rooms. Because of a potential of very high data rate in short range, applications requiring a higher data rate are also possible with a range from 1 to 4 meters, for example a high quality multi-media transfer between a DVD player and a screen. In the same manner, the UWB promoters also proposed a wireless alternative for the Ethernet standard.

30

Ultra-Wideband Radio Propagation Channels

In addition, UWB applications are expected to be used for house automation, where a great number of devices able to communicate at a distance of several dozen meters are deployed in an office or residential environment. In this usage, the exploited characteristics of UWB systems are the low costs of the equipment and the possibility of obtaining localization information. Such potential house automation applications include detection of intrusion, or the electronic reception (owner detection and launching of services like the unlocking of doors). In outdoor scenarios, UWB technology will be used for point-to-point communication applications. An example usage is the transfer of data between several personal devices. In addition, some studies are in progress concerning services of multimedia contents diffusion from electronic kiosks. An example of application typical of such electronic kiosks is the download of stockmarket information on a portable digital assistant (PDA) every time the user is waiting at his regular subway station. Finally, UWB applications are also envisioned in the industrial context. By exploiting the possibilities of long range localization combined with information transfer, sensor networks could be deployed in the productions lines or warehouses, in order to follow-up and automatically manage the operations. This kind of application is well suited for UWB low data rate and long range communication. The main challenge to be raised for this type of applications is the control of radio communication under difficult propagation and interference conditions. 1.5. Regulation evolution The bandwidth of UWB signals requires a strict regulation of their transmission spectrum. Indeed, many systems, whether licensed or not, are presented in UHF and SHF bands, which are very favorable for radio systems deployment. To allow the use of UWB signals over several GHz, regulatory authorities imposed a strict limitation on the transmission power. Figure 1.3 shows some radio systems existing in UHF and SHF bands. We can note that there are reserved bands for several systems like the standards of cellular telephony GSM (900 MHz), DCS (1.8 GHz) and UMTS (2 GHz). The global positioning system (GPS) also occupies a reserved band around 1.5 GHz. Other frequency bands are already used for unlicensed communication systems. For example, the ISM band is used by systems such as Bluetooth, WiFi and DECT, and is also authorized for domestic devices such as microwave ovens. The UNII band is the frequency band where the WiFi 802.11a and HiperLAN standards operate. In order to limit the UWB signals effects on the other radio systems, the regulatory agencies agree on the use of the 3.1–10.6 GHz band for UWB

UWB Technology and its Applications

31

Power spectral density (dBm.MHz-1)

UNII

GPS DCS UMTS ISM

GSM

signals [AIE 03b].5 This part of the radio spectrum allows us to use a bandwidth as wide as 7.5 GHz, while avoiding telephony systems and GPS. The very low authorized power spectral density, located under the level of unintentional emission fixed by the FCC (−41.3 dBm.MHz−1 ), is compensated by the bandwidth, allowing it to emit a total power of 0.6 mW.

Bluetooth, 802.11b, DECT, microwave ovens

802.11a, HiperLAN Unintentional radiation limit (-41.3 dBm.MHz-1) UWB

0.9 1.5 2.0 2.4 3.1 1.8

5

10.6 Frequency (GHz)

Figure 1.3. Radio systems in UHF and SHF bands

1.5.1. Regulation in the USA In the USA, the regulatory agency FCC launched its first works on UWB radio technology as early as 1998 [MOR 03, POR 03a]. In May 2000, a first proposal for a regulation was published (Notice of Proposed Rule Making), which led to the current regulatory text Report & Order of February 2002 [FCC 02]. The FCC rules of the UWB spectrum regulation enable it to emit signals mainly in the frequency band 3.1–10.6 GHz, by respecting a power spectral density lower than the one applied to non-intentional radio transmissions. Three different classes of equipment are considered: • Visualizing systems: ground penetrating radars, through-wall visualizing systems, medical systems and monitoring systems. 5. We will see that in certain regions of the world (Europe, Asia), only a part of the 3.1–10.6 GHz band is considered.

32

Ultra-Wideband Radio Propagation Channels

• On-board radar systems: for example, the radars for cars in the 24–29 GHz band. • Communication and measurement systems.

UWB EIRP emission level (dBm.MHz-1)

Each class of equipment has its own emission mask. Figure 1.4 presents the emission mask of the communication systems, for indoor use. The spectrum was defined to ensure a protection of the sensitive systems, more particularly the GPS (1.2–1.5 GHz), and the bands dedicated to civil aviation. -35

FCC (indoor)

7.25 10.25

-40

CEPT

-45

MIC (proposal)

1.99

-50

Singapore (UWB Friendly Zone)

10.6

3.1

-55 -60 -65

GPS band

-70 -75

2.7 3.8 6

0.96

8.5

1.61

1

10

Frequency (GHz)

Figure 1.4. UWB systems emission masks

1.5.2. Regulation in Europe In Europe, the European Telecommunications Standards Institute (ETSI) has operated since 2001 on the attribution of the frequencies in Europe for UWB systems. The studies are carried out in close cooperation with group SE24 of the Conf´erence Europ´eenne des Postes et T´el´ecommunications (CEPT), which more particularly analyzes the possible impact of the UWB systems on the existing ones [POR 03b]. Normally, these European authorities aim to reach a given accord for all the European Union States, but each national regulatory agency keeps the right to manage its radio spectrum independently. Compared to the American regulation, a more restrictive position was adopted by the CEPT. In a decision presented in March 2006 [ECC 06], the regulatory organization Electronic Communication Committee (ECC) proposed a spectral mask limiting the emission of UWB signals to the

UWB Technology and its Applications

33

6–8.5 GHz band with a power spectral density of −41.3 dBm.MHz−1 , are shown in Figure 1.4. The emission is also authorized in the band 3.8–6 GHz with a power spectral density of −70 dBm.MHz−1 . However, we should note that such a power limitation does not make it possible to carry out reliable communication systems for a distance of about one meter. In order to encourage a fast emergence of UWB systems in Europe, the ECC currently considers the possibility of using mitigation techniques to ensure the compatibility of UWB systems with the other radio services in the 3.1–4.8 GHz band. Among these mitigation mechanisms, we can find the detection and avoidance (DAA) systems which allow us to avoid bands already used by other systems and the use of low duty cycle (LDC). Hence, all UWB systems using satisfactory mitigation mechanisms could be authorized to emit with a power spectral density of −41.3 dBm.MHz−1 in the 3.1–4.8 GHz band. Temporarily – until June 2010 – the ECC authorizes the emission in the 4.2–4.8 GHz band with a power spectral density of −41.3 dBm.MHz−1 . 1.5.3. Regulation in Asia In Asia, the regulation of UWB is particularly well advanced in Japan and Singapore. In Japan, from September 2002, the Information and Technology Communication Sub-Council working group presented its first investigations on UWB technology at the ministry for telecommunications, in order to prepare the regulation of UWB. Moreover, the Communications Research Laboratory (CRL) is developing a project with many industrial partners in order to design marketable UWB systems. However, the emission mask proposed by their ministry of internal affairs and communications, MIC, remains more restricted than the American mask. As illustrated in Figure 1.4, a preliminary proposal presented in August 2005 suggests a limitation of UWB emissions to the 7.25–10.25 GHz frequency bands with a power spectral density of −41.3 dBm.MHz−1 . At the beginning of 2003, the Singaporean regulatory agency named Infocom Development Authority (IDA) created a UWB research area, called UWB Friendly Zone, which makes it possible to deploy tests and demonstrators in Singapore with experiments using an emission power of about 10 dB above the FCC limit and a band spreading from 2 GHz to 10 GHz [POR 03b]. With that, the IDA tries to give an significant advance in Singapore to new telecommunication technologies, in order to remain scientifically and economically competitive. To conclude, it should be specified that the greatest constraint of regulation comes from management of the interference. The problems of UWB regulation

34

Ultra-Wideband Radio Propagation Channels

do not come from the effect of only one UWB system, but from the aggregation of hundreds of devices using this technology, creating a sum of signals which can possibly interfere with other systems, like the navigation or safety systems. So, the UWB scientific community currently works to test and define systems which remain inoffensive, even when using several colocalized equipments. 1.6. UWB communication system and standardization The emission mask of UWB radio signals established by the FCC allows the use of various signals. Figure 1.5 presents various solutions which can be considered. For each approach, the used frequency band as well as the emission mask of the FCC are presented in the left-hand graph. In each case, the right-hand graph presents the time domain signal corresponding to the band represented in solid line. As we can observe, the duration of the obtained impulse is inversely proportional to the bandwidth used. The mono-band approach consists of using all the frequency band available. It is characterized by very short impulses, therefore resistant to the effects of superimposed multipaths, and the signals can be created from an arbitrary impulse modeled by an adequate filter. However, this approach allows little flexibility in the use of the radio spectrum, and requires us to use very powerful radio frequency (RF) components. Another solution consists of dividing the allocated UWB spectrum into two parts: it is the dual bands approach. It makes it possible to use cheaper integrated circuit technologies, especially for the low band (typically 3–6 GHz), the high band being used according to the development of new RF components. The flexibility of the spectrum radio remains moderate, but this solution allows it to avoid an arbitrarily sensitive band, as the UNII band around 5 GHz for example. Finally, the multiband approach consists of using frequency bands of minimal width about 500 MHz. This solution has a very great flexibility for radio spectrum management. For example, if the emission mask is more restricted in a given country, we can avoid the subbands which are not authorized. The management of the multi-user communications is also simplified, as many frequency combinations or temporal multiplexings are possible. Many modulation techniques were developed from these various UWB signals. Historically, the first form of modulation suggested for UWB was the impulse radio [SCH 93]. Regarding standardization, the American institute IEEE began the work of defining a high data rate communication system

UWB Technology and its Applications

35

using the UWB spectrum in 2002. The choice of the type of modulation for this system was the subject of a procedure of very strict selection, within the 802.15.3a work group. The debate for a single solution was mainly articulated around two proposals: Direct Sequence UWB (DS-UWB), proposed by the consortium UWB Forum [FIS 04] and MultiBand Orthogonal Frequency Division Multiplexing (MB-OFDM), proposed by the consortium MultiBand OFDM Alliance/WiMedia Alliance [BAT 04b]. In January 2006, as no consensus could be found for a single solution, the IEEE 802.15.3a group was disbanded. Today, only one industrial standard exists concerning UWB systems: the standard ECMA-368 [ECM 05], developed by the consortium WiMedia Alliance and based on MB-OFDM. 1.6.1. Impulse radio The impulse radio concept, developed from radar studies, corresponds to the emission of impulses of very short duration (around 100 ps to 1 ns). Typically, this type of impulses occupies a very broad spectrum (about 1 to several GHz). It is thus a mono-band approach. The impulse signals generally adopted for UWB communications include the Gaussian impulse, its first derivative (Gaussian monocycle), and its second derivative, as represented in Figure 1.6. The drawback of the Gaussian impulse lies in its non-zero mean value, which corresponds in the frequency domain to an important continuous component. Thus, the Gaussian impulse cannot be propagated without deformation, and we generally prefer the Gaussian monocycle [BAT 03]. 1.6.1.1. Pulse position modulation Relation [1.3] gives the typical expression of a transmitted impulse radio signal, using a pulse position modulation (PPM) [SCH 97a]:    [1.3] w t − j · Tf − cj · Tc − Δ · d j  s(t) = Ns

j

where w(t) represents the waveform of a transmitted monocycle, normally starting from t = 0. Thus, the transmitted signal corresponds to a sequence of impulses transmitted at different times, the j th impulse being transmitted at j · Tf + cj · Tc + Δ · d j  . Ns

The term j · Tf allows a uniform spacing of the impulses. Indeed, the signal defined by:    [1.4] s(t) = w t − j · Tf j

36

Ultra-Wideband Radio Propagation Channels

(a ) 1 Normalized signal

Power spectral density (dBm.MHz -1 )

-40 -50 -60 -70 -80

0

5

10

0.5 0 -0.5 -1

15

0

0.1

0.2

0.3

0.4

(b) 1 Normalized signal

Power spectral density (dBm.MHz -1 )

-40 -50 -60 -70 -80

0

5

10

0.5 0 -0.5 -1

15

0

0.5

1

1.5

2 Time (ns)

4

(c) 1 Normalized signal

Power spectral density (dBm.MHz -1 )

-40 -50 -60 -70 -80

0

5 10 Frequency (GHz)

15

0.5 0 -0.5 -1

0

Figure 1.5. UWB spectrum and signals: mono-band approach (a), dual-band approach (b) and multiband approach (c)

2

UWB Technology and its Applications

37

1

Normalized signal

Gaussian pulse 0.5

Gaussian monocycle Second derivative

0

-0.5

-1

0

0.2

0.4 0.6 Time (ns)

0.8

1

Figure 1.6. UWB impulse waveforms

corresponds to a sequence of impulses uniformly distributed, with a pulse spacing equal to Tf seconds. The impulse sequence of relation [1.4] is represented in Figure 1.7(a). Tf is generally called “frame duration” and is about 100 to 1000 times the impulse duration. This makes it possible to obtain signals with a low duty cycle, and therefore with a low power spectral density. However, we should note that the periodicity of this signal generates parasitic spikes in the radio spectrum. In addition, impulses cyclically transmitted by the users of the network are very sensitive to collision when the signals access the channel. These two problems are solved by the use of a temporal pseudo-random hopping code. The frame of duration Tf is subdivided in a given number of time intervals (chip) of duration Tc . Each user is provided with a pseudo-random code {cj } of length Ns which indicates in which chip of each frame the impulse must be transmitted. The use of a pseudo-random code makes it possible to decrease the effect of appearance of spikes due to the periodicity of the frame, and the spectrum appears much more smoothed [PEZ 03]. If the pseudo-random sequence is sufficiently long, the UWB signal can be compared, on the occupied band, to a Gaussian white noise. In addition, the pseudo-random code allows the management of multi-users on the radio channel. The transmitted signal with the considered code is expressed by:    [1.5] w t − j · Tf − cj · Tc s(t) = j

and its shape is given by Figure 1.7(b).

38

Ultra-Wideband Radio Propagation Channels

Tf (a) t Tc (b) t

(c) t

Figure 1.7. Sequences of radio impulses: (a) sequence of uniformly distributed impulses, (b) spreading code at position 0, and (c) spreading code at position 1

In relation [1.3], the modulation used to transmit data is PPM. Indeed, the term Δ represents a time interval of about T2c , and the dk terms are the 0 and 1 symbols to be transmitted. The index d j  , where · indicates the integer Ns part, shows that the same symbol is used over the whole length of the code. There is thus a redundancy of information, which makes it possible to increase the processing gain. Under these conditions, when zero is transmitted, there is no temporal shift in the emission of the data, while a duration shift of Δ is applied over the entire code duration when one is transmitted. These two states are shown in Figure 1.7(b) and (c). We can note that PPM modulations using a greater number of states are possible. Concerning impulse radio, the signals reception is done by correlation. The basic idea is to multiply the received signal by a model signal, which makes it possible to demodulate the transmitted data. So, the model signal corresponds to a given pseudo-random emitted code. Thus, the use of time codes allows the management of multi-access [SCH 93]. If several users emit simultaneously by using orthogonal pseudo-random codes, only the signal corresponding to the selected code will be demodulated, the other users will appear as noise. This scheme corresponds to the traditional code multiple division access (CDMA). 1.6.1.2. Pulse amplitude modulation The pulse amplitude modulation (PAM) is an alternative to the pulse position modulation. This technique consists of varying the amplitude of the transmitted impulses to code the different states. Theoretically, an unlimited number of different values can be used for the signal amplitude. In practice, the PAM modulation is often reduced to two

UWB Technology and its Applications

39

states, 1 and -1. Under these conditions, 2-PAM modulation may be regarded as a form of binary phase shift keying (BPSK). This BPSK modulation has a good robustness to the effects of the channel and simplifies the synchronization. Indeed, the position of the impulse remains fixed, and it is only its phase which varies. Another alternative of the PAM modulation consists of transmitting two states: 1 and 0. This corresponds to an on-off keying (OOK) modulation. In each defined transmission time-slot, an impulse is emitted to code 1, and nothing is emitted to code 0. Finally, we may also consider hybrid modulations. We can for example create a modulation of 512 states by using a combination of 256-PPM with a modulation 2-PAM. The impulse radio modulation technique was implemented by the American company Time Domain, and was marketed in an electronic chip, named PulsOn 210. However, because of the difficulty of implementation and the low spectral flexibility of this type of system, the standardization authorities have chosen other types of modulations, presented in the following subsections. 1.6.2. Direct sequence UWB The direct sequence ultra-wideband (DS-UWB) modulation is a solution proposed by the industrial group UWB Forum [FIS 04]. This modulation uses the frequency band allocated to UWB under two dual bands covering respectively 3.1–4.85 GHz and 6.2–9.7 GHz. This configuration make it possible to avoid the UNII band at 5 GHz used by WiFi systems. On these dual bands, the transmitted impulses have a time duration of about 0.3–0.5 ns and present several cycles (see Figure 1.5(b)). In a first step, only the low band is used, in order to simplify the architecture of the radio transmission systems. As with the PPM modulation, the DS-UWB modulation uses a frame divided in chips. However, an impulse can be transmitted in each chip of the frame. So, the signal is transmitted continuously and there is no low duty cycle as in the case of the impulse radio. The transmitted symbols are represented by ternary spreading codes of one frame length, composed of a series of 1, 0 or −1. According to the specifications proposed by the UWB forum, all the DS-UWB systems will be able to provide these codes using a BPSK baseband modulation. Optionally, a more efficient modulation, named M-BOK, is defined in order to ensure a more robust transmission. The length of the spreading code varies from 1–24 chips according to the considered data rate. The transmission data rate proposed for the DS-UWB systems

40

Ultra-Wideband Radio Propagation Channels

range from 28–1,320 Mbps. The management of multiple users, clustered in sub-networks called piconets, is performed by the use of orthogonal codes. In this prospect, the DS-UWB modulation is similar to the CDMA system used in UMTS. Finally, we can note that the isolation of users belonging to different piconets is improved by the use of slightly different chip frequencies into each piconet. More details on this technology can be found in [WEL 03]. Compared to impulse radio, the DS-UWB systems seem easier to implement, because the considered frequency bands are narrower, which imposes less constraints on RF components. The used modulation still being based on impulses, this radio access technique is robust against the multipath effects of the channel. In terms of regulation, the separation into two dual bands makes it possible to protect the sensitive frequency bands, but the transmitted spectrum is not very flexible. In terms of standardization, we may notice that following the disbanding of the IEEE 802.15.3a working group, no official norm is currently based on the DS-UWB modulation. However, some industrial companies are developing this technical solution, starting from the specifications proposed by the UWB Forum group. As an example, the company Freescale Semiconductor, founder of the UWB Forum group, implemented the DS-UWB modulation in the component Freescale XS110. 1.6.3. Multiband OFDM Multiband orthogonal frequency division multiplexing (MB-OFDM) is a solution based upon the UWB spectrum proposed in standardization and used by the industrial groups MBOA and WiMedia Alliance [BAT 04b]. It is a multiband approach, where the FCC spectrum is subdivided into 14 subbands of 528 MHz. Figure 1.8 shows these subbands which are divided into different groups. First of all, the industrial companies focussed their development efforts on group 1 (3.1–4.9 GHz). The other groups should be quickly exploited in order to produce systems in conformity with the European and Asian regulation. In each subband, an OFDM modulation is applied, the signal being distributed over 100 carriers with narrow bandwidth. For each carrier, the baseband modulation is either BPSK or QPSK. This configuration facilitates a very flexible management of the radio spectrum. Indeed, to avoid the jamming of any frequency band, we can forbid a series of carriers or the totality of a subband. This management can possibly be performed according to the legislation of the country of use or in a dynamic way according to the potential jammers. The management of the multi-users of the same group of subbands is performed using time-frequency code techniques. In a group of subbands, the communication of a given user regularly hops from one band to another, according to a cycle of approximately 1 μs duration. The hopping pattern

UWB Technology and its Applications

41

from one band to another corresponds to the considered time-frequency code, which is unique to each user. The data rates offered by this technology extend from 53.3–480 Mbps. References [BAT 04a, BAT 04b] give all the necessary details for the implementation of this system. Group 1 Gr. 2 Gr. 3 Gr. 4 Gr. 5 ← →← →← →← →←→

Power spectral density (dBm.MHz-1)

-40

-50

-60

-70

-80

0

2

4

6 8 Frequency (GHz)

10

12

Figure 1.8. Subbands for the MB-OFDM solution

The advantages of the MB-OFDM radio access technique are mainly related to its low complexity of implementation, as the OFDM modulation shows a high degree of maturity. Moreover, it is currently the only UWB communication technique developed as an international standard, ECMA – 368, available since December 2005. The restriction on the used frequency band to the first group of subbands allows it to use existing systems and RF components. However, in order to achieve an international deployment of the MB-OFDM solution, it will be necessary to develop systems operating under the European and Asian frequency regulations. In technical terms, it should be noted that signals are no longer impulsional, and the technology no longer benefits from the advantages related to a very wide frequency band, such as the robustness to the radio channel effects or the possibilities of localization. The integrated circuit UBLink proposed by the company Wisair is an example of commercially available MB-OFDM design.

1.7. Conclusion Initially used for radar localization applications, UWB technology has been studied for the last 15 years in the field of wireless communications. The main characteristics of this technology, like the width of the spectrum

42

Ultra-Wideband Radio Propagation Channels

and its strong temporal resolution, made it possible for the scientific and industrial communities to propose a certain number of interesting applications: high data rate WLAN networks, home automation applications, etc. As developed in this chapter, various types of UWB modulations were proposed in standardization, in particular DS-UWB and MB-OFDM. UWB regulation has been effective in the USA since 2002. In Europe, a mask of emission for UWB signals was established in 2006, but the coexistence of UWB systems with other applications is still under study. As for any radio access technique, an accurate knowledge of the propagation channel as well as the antennas is predominant for the development of UWB communication systems. Thus, the following section presents the radio waves propagation phenomena inside buildings, and describes the principal parameters for UWB radio channel characterization. In this book, we address antennas by including them in the channel. A thorough study of the antennas in the specific case of UWB could be the subject of a specific book. Indeed, the realization of an antenna presenting good characteristics in terms of adaptation and radiation on such a broad band is still a challenging task [SCH 03c, SCH 03b, OSS 03].

Chapter 2

Radio Wave Propagation

2.1. Introduction The existence of electromagnetic waves was theoretically predicted by J.C. Maxwell as early as 1855 [MAX 55]. The German physicist Hertz tried to demonstrate that electromagnetic waves travel at a finite speed, and in 1886 he performed the very first radio propagation experiments. The oscillating circuit designed by Hertz consisted of two discharging metallic spheres, which produced an observable spark on an open wire loop [SCH 86]. Interestingly, the signal used by Hertz consisted of a short duration pulse, which could hence be regarded as an ultra-wideband signal [AIE 03a]. In order to facilitate the industrial use of radio transmission, a large amount of research has been conducted to characterize the electromagnetic wave propagation mechanisms. This research first focused on signals confined in narrow frequency bands and then extended to wideband signals. This chapter details the definition of the propagation channel and its mathematical representation. The characteristic parameters of the radio-mobile channel are then presented. 2.2. Definition of the propagation channel By definition, a radio transmission system transforms an emitted electrical signal e(t) into a received electrical signal s(t) by means of electromagnetic waves. The propagation channel corresponds to the system converting the signal e(t) into the signal s(t) and thus accounts for the interactions between the electromagnetic waves and their environment. At this point, a distinction should be made between the propagation channel and the transmission

44

Ultra-Wideband Radio Propagation Channels

channel. The propagation channel represents the transformation of the electromagnetic waves throughout their propagation, while the transmission channel also includes antenna radiation patterns (cf. Figure 2.1). In the literature, some authors assimilate these two concepts, but the distinction comes fully into play when considering multiple-input multiple-output (MIMO) channels [COS 04]. The full study of antennas in the specific UWB context would require a dedicated book. Indeed, the development of a UWB antenna presenting adequate characteristics in terms of adaptation and radiation over such a wide frequency band is still a challenging issue [SCH 03c, SCH 03b, OSS 03]. Transmission channel Emitted signal

Received signal

e(t)

s(t) Propagation channel

Figure 2.1. Propagation channel and transmission channel

2.2.1. Free space propagation Let us first consider an ideal case where the transmission system is placed in free space, i.e. in an environment where no obstruction is present. Denoting by GE the emission antenna gain and PE the emitted signal power, the power density observed at a distance d is given by [PAR 00]: W =

PE GE 4πd2

[2.1]

The power PR collected at the output of a receiving antenna with gain GR relates to the power density W as follows: PR = W AR = W

λ2 GR 4π

[2.2]

where AR represents the effective area of the receiving antenna, and λ represents the wavelength at the working frequency.

Radio Wave Propagation

45

Equations [2.1] and [2.2] yield the Friis formula, giving the signal attenuation in free space: 2  c PR = GT GR [2.3] PT 4πf d where we used the relation c = f λ existing between the wavelength λ, the frequency f and the propagation speed c. It should be noted that this relation holds for a distance d large enough for the receiving antenna to be considered in the far field region with respect to the transmitting antenna [AFF 00]. A receiver is situated in the far field if the distance d is larger than the Fraunhofer distance dF , which is related to the largest dimension of the transmitting antenna D and to the wavelength λ as follows:1 2D2 [2.4] dF = λ Free space propagation is a theoretical or reference situation. In realistic propagation conditions, the transmitted wave is affected by the system environment through different mechanisms, which are presented in the following section. 2.2.2. Multipath propagation In a realistic environment, signal transmission follows not only the direct path, but also a number of distinct propagation paths. These paths undergo various effects depending on the type of interaction between the wave and the surrounding objects. At the output port of the receiving antenna, the observed signal corresponds to a combination of different waves, each of them presenting a different attenuation and a different phase rotation. Moreover, each wave reaches the receiver with a distinct delay, linked to the length of the propagation path. Multipath propagation mechanisms may lead to a significant distortion of the received signal. On the other hand, a direct path, known as the line of sight (LOS) path, is not always available, which is particularly frequent in indoor configurations. In this case, so called non-line of sight (NLOS) paths are necessary to enable efficient radio communication. Figure 2.2 illustrates the concept of multipath propagation, as well as the main propagation phenomena.

1. It should be noted, though, that for systems operating at different frequencies, the antenna dimension D is generally adapted to the wavelength. For a wire antenna, the antenna length is for instance defined as D = λ2 , and hence the Fraunhofer distance follows dF = λ2 .

46

Ultra-Wideband Radio Propagation Channels

Diffuse reflection Ȝ Diffuse scattering

Transmission

Receiver

Diffraction Specular reflection Transmitter

Waveguide effect

Figure 2.2. Main propagation mechanisms

• Reflection: reflection takes place on obstacles of large dimensions with respect to wavelength. When two different materials are separated by a plane surface (i.e. a surface where possible rough spots are small with respect to the wavelength), the reflection is said to be specular. In this case, the direction and the amplitude of the reflected ray are governed by the Snell-Descartes and Fresnel laws. When the surface separating the two materials presents non-negligible random rough spots, the reflection is called diffuse reflection. Most of the energy is then directed along the reflected ray, but part of the energy is diffused in neighbor directions.

Radio Wave Propagation

47

• Transmission: when the medium where a reflection takes place is not perfectly radio-opaque, part of the incident wave travels through the material following a so-called transmission mechanism. Most of the building materials used in indoor environments significantly attenuate the transmitted wave. For a given material, the attenuation and the direction of the transmitted signal are related to the wavelength, since the refractive index of the material varies with the frequency. Finally, for layered materials such as plasterboard, multiple reflection may occur within the material. • Diffraction: diffraction takes place on the edges of large sized obstacles with respect to the wavelength. This mechanism accounts for the electromagnetic field continuum on either side of the optical line of sight. The calculation of a diffracted field uses Huygens’ principle, which considers every point of a wavefront as a secondary spherical source. Hence, diffracted waves are distributed along a geometrical cone, with an angle corresponding to the incident angle. • Diffusion: when an electromagnetic wave travels towards a group of obstacles of small dimensions with respect to the wavelength, the observed phenomenon corresponds to the superimposition of a large number of random diffractions. In this case, the behavior of the incident wave is handled in a statistical way and the resulting phenomenon is called diffusion. In general, the electromagnetic wave is directed in all directions with a variable attenuation. This phenomenon is generally observed in outdoor environments, for instance in the presence of tree foliage. In indoor environments, diffusion may occur on a group of small objects. • Waveguide effect: the waveguide effect occurs in indoor environments, between two corridor walls for instance. Successive reflections on two parallel obstacles lead to a global wave motion along the guiding direction. This phenomenon also occurs in urban environments, for instance between two buildings lining a narrow street. 2.2.3. Propagation channel variations Owing to the different interactions between the radio waves and their propagation medium, significant variations of the channel characteristics are observable at different scales. When isotropic antennas are used in free space, the resulting power attenuation is proportional to the square of the distance d between the antennas (cf. section 2.2.1). However, actual observations present large scale power variations linked to the propagation environment. In practice, the obstacles within the environment as well as the combination of multiple propagation paths lead to an additional attenuation of the

48

Ultra-Wideband Radio Propagation Channels

transmitted waves. In general, this attenuation is a function of the distance d between the transmitter and the receiver. It is characterized by the path loss exponent Nd , the received signal power decreasing proportionally to d−Nd . The parameter Nd is equal to 2 in free space, and varies between 2 and 5 in NLOS configurations. In LOS configurations, waveguide effects may lead to a value of Nd lower than 2. Finally, we may note differences in the order from 1 to several dB between the received power and the mean trend following a d−Nd law. This is due to occasional obstructions known as shadowing or slow fading. Small scale fluctuations are directly linked to multipath propagation mechanisms. Multiple versions of a single signal presenting different attenuations and different phase delays may eventually combine at the receiver, which produces significant fast fluctuations in the order of 10 to 20 dB. 2.2.3.1. Spatial selectivity Let us consider a signal composed of a single carrier frequency propagating along two paths, the direct path and a reflected path. If the reflection occurs in the vicinity of the LOS path, we may consider that these two paths will cause a similar attenuation. However, depending on the wavelength of the transmitted signal and on the length difference between the two paths, the two versions of the signal may arrive in phase or antiphase. This concept is illustrated in Figure 2.3. In the first case, the signals are adding constructively and some power gain is observed. In the second case, the signals are adding destructively and the total received power is strongly attenuated. When the mobile device is displaced, the phase rotation linked to each path leads to a series of signal peaks and signal fades, which is called a fast fading signal. When this phenomenon occurs with a large amount of paths, the received signal may be considered as a random process. 2.2.3.2. Frequency selectivity Let us now consider a more realistic signal, spreading over a given frequency bandwidth. As explained in the previous section, the spatial selectivity phenomenon depends on the phase difference between multiple paths. Thus, spatial selectivity also depends on signal frequency. When the frequency band is narrow, all frequencies forming the transmitted signal undergo similar phase variations. Hence, the possible power fades are constant over the whole considered frequency band. This phenomenon is known as flat fading. For signals occupying wider frequency bands, the various frequencies may be affected in a different way, and thus the received signal is somehow

Radio Wave Propagation

V

49

t1 direct path t

V

t2

reflected path (case 1) t

V

t2 + ǻt

reflected path (case 2) t

case 1 V

global signal t case 2

Figure 2.3. Constructive and destructive addition of two propagation paths

distorted with respect to the transmitted signal. In this case, we may observe frequency selective fading, which consists of a variation in the power received with increasing frequency. The bandwidth over which the frequency components are affected in a similar way is called the coherence bandwidth or correlation bandwidth. In the delay domain, frequency selectivity corresponds to a delay between the various versions of the signal propagating along different paths. This delay is in the order of a few nanoseconds in indoor environments, and in the order of a few microseconds in outdoor environments. Depending on the signal bandwidth, these echoes may superimpose on each other, which results in significant fades. For signals presenting a very wide frequency band, and particularly for UWB signals, the time domain resolution is very high, which limits the possible interference between different delayed versions of the transmitted signal. In this case, signal fading is less pronounced. It is then possible to apply advanced reception techniques, such as channel equalization or RAKE reception,2 in order to collect as much energy as possible from the multiple propagation paths [CRA 98, FOE 01b, GAU 03].

2. A RAKE receiver combines the signals from different multipaths, by using several reception branches in parallel [HAY 01].

50

Ultra-Wideband Radio Propagation Channels

Finally, it should be noted that in the case of wideband signals, frequency selectivity leads to a time domain spreading of the transmitted signal. Characterizing this spreading is essential to calibrate communication systems and mitigate intersymbol interference.3 2.2.3.3. Doppler effect The spatial selectivity phenomenon demonstrates that the properties of the radio propagation channel may vary significantly when the receiving antenna is positioned at different locations. It is thus questionable how the propagation channel is affected when the transmitting antenna, the receiving antenna or even the environment are moving. The Doppler effect corresponds to an observed shift in the frequency of an electromagnetic signal due to the variation of its propagation path. As a simple example, let us consider a mobile receiver moving at a speed v and receiving a radio signal as a plane wave arriving with an angle α with respect to the mobile direction. In this case, the observed Doppler shift is [PAR 00]: v [2.5] ν = f cos(α) c where f is the signal frequency and c is the wave propagation speed. The statistical case where the ray distribution is represented by the probability density function (PDF) of their angle of arrival pα (α) was developed in [CLA 68]. For a simple case where the handset moves at a constant speed, the PDF of the Doppler shift pν (ν) is given by:     

 ν ν 1 [2.6] pν (ν) =  ν 2 · pα − arccos νmax +pα arccos νmax 1− νmax where νmax is the maximum Doppler shift given by: v νmax = f c

[2.7]

This theoretical PDF of the Doppler shift may be linked to the Doppler spectrum of a measured signal. In particular, for a uniform distribution of the arrival angles, the PDF of the Doppler shift is proportional to the Jakes Doppler spectrum [JAK 93]: pν (ν) =

1  ν 2 π 1 − νmax

[2.8]

3. Intersymbol interference consists of the corruption of a transmitted symbol by the previous symbols due to the time domain spreading generated by the propagation channel. It is one of the main sources for the degradation of the transmission quality.

Radio Wave Propagation

51

In what follows, a distinction will be made between the concepts of temporal and spatial variations. Spatial channel variations are due to the displacement of at least one of the antennas in an otherwise static environment. Temporal variations are linked to a change in the close environment of a fixed radio link [HAS 94a]. In the radio-mobile context, both types of variation are generally observed, but one or the other may be considered as predominant, depending on the situation. In the indoor environment, temporal variations are mainly due to moving people. In both cases of spatial and temporal variations, propagation paths between the transmitter and the receiver may appear, disappear or undergo successive transformations. In the case of a stationary channel, only the existing paths are considered, and the channel variations consist of an evolution of the path length, which may be positive or negative. Hence, both spatial and temporal channel variations lead to an observed Doppler effect.

2.3. Propagation channel representation 2.3.1. Mathematical formulation Owing to the multipath propagation phenomena, the received signal s(t) is composed of a number of superimposed replicas of the transmitted signal e(t), each of them presenting a different delay and a different attenuation. The propagation channel thus behaves like a linear filter. Hence, the propagation channel may be represented by its impulse response (IR) h(τ ), corresponding to the output of this filter when the excitation is a Dirac function. The received signal may thus be written as: s(t) =

∞ −∞

e(t − τ )h(τ )dτ

[2.9]

In most radio systems, the transmitted signal spreads over a frequency band which is not centered around zero. A given signal x(t) may thus be represented by its complex envelope γx (t) defined as: 

x(t) =  γx (t)ej2πf0 t

[2.10]

where {·} represents the real part of a complex number and f0 represents a given frequency in the considered band. The complex envelope γx (t) is also named the equivalent baseband term of x(t).

52

Ultra-Wideband Radio Propagation Channels

It can be shown that there are two ways of defining the baseband filter heq (τ ) equivalent to the passband filter h(τ ) (cf. Appendix A): heq1 (τ ) =

1 γh (τ ) 2

[2.11]

−j2πf0 τ

heq2 (τ ) = h(τ )e

The three representations in Figure 2.4 are thus equivalent to observing the channel effect on the transmitted signal. In the remainder of this book, we will use, unless otherwise stated, the channel impulse response in its complex envelope form γh (τ ), which will be denoted h(τ ) for the sake of simplicity. e(t)

s(t) -

-

h(τ )

γe (t)

γs (t) -

heq1 (τ ) =

-

1 2 γh (τ )

γe (t)

γs (t) -

−j2πf0 τ

heq2 (τ ) = h(τ )e

-

Figure 2.4. Equivalent representations of a static radio-mobile channel

2.3.2. Characterization of deterministic channels The representation of the radio channel in the form of an IR h(τ ) is valid for static channels only. In practice, the environment or the antenna position may be modified, and hence the radio channel may vary with time. The IR h(t, τ ) is thus dependent on both time and delay. The inputs and outputs of a linear filter may be described in the time domain or in the frequency domain. This leads to a set of four transfer functions that may be used to describe the radio channel [BEL 63]. Figure 2.5 illustrates the relations between these functions.

Radio Wave Propagation

53

time-delay  F delay-Doppler

−1

h(t, τ )

F



@ I @ @ @ F −1 F@ @ @ @ @ @ frequency-time R @ @

S(τ, ν)

T (f, t)

@ I @ @ @ @ @ F −1 F@ @ @ @ @ R @

 F −1 F H(f, ν)



frequency-Doppler Figure 2.5. Characteristic functions for a deterministic channel. Arrows represent a Fourier transform (F ) or an inverse Fourier transform (F −1 )

2.3.2.1. The time varying impulse response The function h(t, τ ) is called the time-variant impulse response. It relates the received signal s(t) to the transmitted signal e(t) according to the following filtering operation: s(t) =

∞

−∞

e(t − τ )h(t, τ )dτ

[2.12]

The magnitude of this impulse response may be observed to distinguish between different signal echoes according to their propagation delay. Equation [2.12] thus provides a physical representation of the channel as a continuum of scatterers that are fixed – since their delay is constant – and scintillating – which corresponds to the channel’s temporal evolution. 2.3.2.2. The frequency domain function The function H(f, ν) is also called the output Doppler-spread function and reflects the Doppler shift phenomenon caused by the channel. It is the dual function of the function h(t, τ ) in the frequency-Doppler shift space. It thus

54

Ultra-Wideband Radio Propagation Channels

relates the received signal spectrum S(f ) to the transmitted signal spectrum E(f ) as follows: ∞ E(f − ν)H(f − ν, ν)dν [2.13] S(f ) = −∞

Using this representation, the output signal spectrum S(f ) is considered as the sum of superimposed input signal spectrum replicas E(f ), each replica being Doppler shifted and filtered. 2.3.2.3. The time varying transfer function Another approach to characterizing the radio channel consists of describing the relation between the time domain output signal s(t) to the input signal spectrum E(f ), using the time varying transfer function T (f, t): ∞ E(f )T (f, t)ej2πf t df [2.14] s(t) = −∞

The function T (f, t) is related to the functions h(t, τ ) and H(f, ν) through a simple Fourier transform. If the bandwidth of the considered channel is narrow enough, the time-variant transfer function may be directly measured using a network analyzer. 2.3.2.4. The delay-Doppler spread function A final approach consists of representing the radio channel in the delay-Doppler shift space. The corresponding function allows us to simultaneously observe the channel dispersion in both the time domain and the frequency domain. For this reason it is referred to as the delay-Doppler spread function. The function S(τ, ν) relates the output signal s(t) to the input signal e(t) through the following relation: ∞ ∞ e(t − τ )S(τ, ν)ej2πνt dνdτ [2.15] s(t) = −∞

−∞

Equation [2.15] represents the output signal s(t) as a sum of superimposed replicas the input signal e(t), each replica being delayed and Doppler-shifted. The function S(τ, ν) is related to the functions h(t, τ ) and H(f, ν) through a simple Fourier transform. 2.3.3. Characterization of linear random channels In practical situations, the propagation channel fluctuations are due to a number of superimposed phenomena, which cannot be measured individually.

Radio Wave Propagation

55

The radio channel variations may thus be regarded as a random process and it is no longer valid to describe them deterministically. The propagation channel is thus characterized in a statistical way. In practice, the statistical description of the channel is limited to the second order, and we consider the autocorrelation functions of the channel system functions only. These functions are defined as follows:   Rh (t, u; τ, η) = E h(t, τ )h∗ (u, η)   RH (f, m; ν, μ) = E H(f, ν)H ∗ (m, μ) [2.16]   RT (f, m; t, u) = E T (f, t)T ∗ (m, u)   RS (τ, η; ν, μ) = E S(τ, ν)S ∗ (η, μ) where E[·] represents the mathematical expectation and (·)∗ represents the complex conjugation operation. These four autocorrelation functions are linked through double Fourier transforms in a similar scheme to the one linking the channel system functions (cf. Figure 2.5). The second order moments of the input and output signals are then given by: ∞ ∞ e(t − τ )e∗ (u − η)Rh (t, u; τ, η)dτ dη Rs (t, u) = −∞

Res (t, u) =

∞

−∞

−∞

[2.17]

Re (t, u − η)h(u, η)dη

The first and second order moments are sufficient to completely describe the output signal s(t) in the case of a Gaussian signal. 2.3.4. Channel classification The representation of the random radio channel may be simplified by considering different assumptions about the channel characteristics. 2.3.4.1. Wide sense stationary channels A channel is considered as wide sense stationary (WSS) if its temporal (or spatial) variation meets the statistical conditions of second order stationarity. In other words, the expectation of the channel impulse response needs to be invariant with time, and its autocorrelation Rh (t, u; τ, η) will depend on the

56

Ultra-Wideband Radio Propagation Channels

variables t and u through the difference ξ = t − u only. In practice, these conditions mean that the channel fluctuation statistics are constant over a short time interval ξ, which is a reasonable assumption for traditional channels (e.g. indoor or urban environment). Under these conditions, the autocorrelation functions of the time-variant impulse response and the time-variant transfer function may be written as: Rh (t, t + ξ; τ, η) = Rh (ξ; τ, η) RT (f, m; t, t + ξ) = RT (f, m; ξ)

[2.18]

Considering the double Fourier transform relationship between Rh (t, u; τ, η) and RS (τ, η; ν, μ), and using ξ = t − u, this yields: RS (τ, η; ν, μ) =

∞

−∞



∞

−∞

= δ(ν − μ)



Rh (t, u; τ, η)ej2π(uμ−tν) dtdu ∞ −∞

Rh (ξ; τ, η)e−j2π(ξν) dξ

[2.19]

= δ(ν − μ)PS (τ, η; ν) where the term PS (τ, η; ν) may be identified as a power spectral density obtained from Rh (ξ; τ, η) by applying the Wiener-Kinchine theorem. This last relation indicates that the spectral content of the signal is uncorrelated for different Doppler shifts. Physically, this means that echoes generating different Doppler shifts are uncorrelated. Similarly, we may write the autocorrelation of the frequency domain function as: RH (f, m; ν, μ) = δ(ν − μ)PH (f, m; ν)

[2.20]

2.3.4.2. Uncorrelated scattering channels Under the uncorrelated scattering (US) assumption, we consider that the contributions from elemental scatterers corresponding to different delays are uncorrelated. This condition is equivalent to an assumption of second order stationarity in the frequency domain. As in the WSS case, we may simplify the autocorrelation functions of the frequency domain function and the time-variant transfer function as follows (and noting by Ω the frequency difference m − f ): RH (f, f + Ω; ν, μ) = RH (Ω; ν, μ) RT (f, f + Ω; t, u) = RT (Ω; t, u)

[2.21]

Radio Wave Propagation

57

The time-variant impulse response and the delay-Doppler spread function may be re-written in the form of power spectral densities: Rh (t, u; τ, η) = δ(η − τ )Ph (t, u; τ ) RS (τ, η; ν, μ) = δ(η − τ )PS (τ ; ν, μ)

[2.22]

2.3.4.3. Wide sense stationary uncorrelated scattering channels A wide sense stationary uncorrelated scattering (WSSUS) channel follows both the WSS and US assumptions. It corresponds to the simplest class of channels, which presents an uncorrelated spread in both the delay domain and the Doppler shift domain. In this case, the autocorrelation functions of the four channel system functions may be simplified as follows: Rh (t, t + ξ; τ, η) = δ(η − τ )Ph (ξ; τ ) RH (f, f + Ω; ν, μ) = δ(ν − μ)PH (Ω; ν)

[2.23]

RT (f, f + Ω; t, t + ξ) = RT (Ω; ξ) RS (τ, η; ν, μ) = δ(η − τ )δ(ν − μ)PS (τ ; ν) Figure 2.6 illustrates the simple Fourier transform relationships linking the four autocorrelation functions for a WSSUS channel. Two of the obtained functions are of particular interest. The function PS (τ ; ν) is called a scattering function. It physically represents the Doppler spectrum of radio wave paths as a function of their propagation delay. For ergodic signals, the function Ph (ξ; τ ) may be written as:   Ph (ξ; τ ) = E h(t + ξ, τ )h∗ (t, τ ) 1 T →∞ T

= lim



T 2

− T2

h(t + ξ, τ )h∗ (t, τ )dt

[2.24]

Hence, the term Ph (0, τ ) corresponds to the temporal average of the impulse response power. This function is called the power delay profile (PDP). In practice, it is generally assumed that observed channels fall under the WSSUS assumption. For measured channels, it is sometimes necessary to

58

Ultra-Wideband Radio Propagation Channels

time-delay  F −1 delay-Doppler

Ph (ξ, τ )

F



@ I @ @ @ F −1 F@ @ @ @ @ @ frequency-time R @ @

PS (τ, ν)

RT (Ω, ξ)

@ I @ @ @ @ @ F −1 F@ @ @ @ @ R @

 F −1 F PH (Ω, ν)



Doppler-frequency Figure 2.6. Autocorrelation functions of a WSSUS random channel

confirm this postulation. A thorough discussion about the validation of the WSSUS assumption for experimental measurements has been published in [BUL 02]. In particular, the RUN method is based on assessments of the process variance over successive sub-intervals [BEN 66]. 2.4. Channel characteristic parameters In order to evaluate the characteristics of a propagation channel, a set of measured impulse responses need to be analyzed. This section presents a number of parameters describing different aspects of the radio channel. In general, their computation requires the WSSUS assumption. As it is not practically feasible to collect a set of statistical channel realizations, we generally assume that the channel system functions are ergodic. Hence, it is for instance possible to approximate the statistical expectation using a temporal (or spatial) average over a set of successive measurements. 2.4.1. Frequency selectivity Frequency selectivity is characterized by the presence of multiple paths, particularly observable on the channel’s impulse response. The power repartition as a function of the delay is given by the PDP, defined by equation

Radio Wave Propagation

59

[2.24]. In order to mitigate the local effects of fast channel fading, the PDP is calculated from a set of M impulse responses, successively measured over a path length in the order of 20–40 wavelengths [LEE 85]. This calculation is valid under the stationarity assumption. The following equation presents the PDP calculation: Ph (0, τ ) =

M 2 1    h tm , τ  M m=1

[2.25]

2.4.1.1. RMS delay spread The root mean squared (RMS) delay spread τRMS , sometimes simply referred to as delay spread, represents the standard deviation of the PDP. It is calculated as follows:   ∞  2  τ − τm Ph (0, τ )dτ −∞  ∞ [2.26] τRMS = P (0, τ )dτ −∞ h where τm is the mean delay given by: ∞ τm = −∞ ∞

τ Ph (0, τ )dτ

−∞

Ph (0, τ )dτ

[2.27]

2.4.1.2. Coherence bandwidth The RMS delay spread is a significant parameter for the analysis of the intersymbol interference. It is also closely linked to the correlation between the different frequencies of the signal spectrum. In order to quantify this frequency dependence, the n% coherence bandwidth is defined from the autocorrelation of the channel transfer function RT (Ω, ξ):     RT (Ω, 0)  = n  = min Ω :  RT (0, 0)  100 

Bc,n%

[2.28]

The function RT (Ω, 0) is referred to as the frequency correlation function and is obtained from the PDP Ph (0, τ ) by a simple Fourier transform. The coherence bandwidth is thus the frequency lag above which the frequency autocorrelation function crosses a given threshold. Thresholds generally given in the literature are 90% and 50% [BAR 95].

Ultra-Wideband Radio Propagation Channels

Relative magnitude (dB)

60

q% of the total energy

Noise level IJ0

IJ1

IJ2

IJ3

Delay (ns)

Figure 2.7. Power delay profile defining the delay window

2.4.1.3. Delay window and delay interval Two other parameters are also used to give a more precise idea of the PDP spread [COS 89]. The q% delay window is the duration of the central part of the PDP containing q% of the total energy. Referring to the delays represented in Figure 2.7, the delay window is given by:   [2.29] Wq% = τ2 − τ1 q% The delays τ1 and τ2 are defined by: τ2 τ3 q Ph (0, τ )dτ = Ph (0, τ )dτ 100 τ0 τ1

[2.30]

and the energy which is outside the window is split into two equal parts. The delays τ0 and τ3 are the delays at which the PDP first rises and finally falls through the signal noise level. The p dB delay interval refers to a threshold positioned at p dB below the maximum of the PDP. It simply corresponds to the interval from the first delay at which the PDP exceeds this threshold to the last delay at which it falls below this threshold.

Radio Wave Propagation

61

2.4.1.4. Exponential decay constants A number of analyses of the UWB radio propagation channel agree on a representation of the impulse response in the form of a discrete sum of individual contributions. Each contribution, known as ray, corresponds to a propagation path and is characterized by its distinct delay and amplitude. This representation is widely used for wideband channels [HAS 93]. In order to account for the possible presence of ray clusters, this discrete impulse response is represented using the formalism proposed by Saleh and Valenzuela [SAL 87]:  

L(t) Kl (t)

h(t, τ ) =

  βk,l (t)ejθk,l (t) δ τ − Tl (t) − τk,l (t)

[2.31]

l=1 k=1

where L(t) is the number of clusters, Kl (t) is the number of rays in the lth cluster, and Tl (t) is the arrival time of the lth cluster. Parameters βk,l (t), θk,l (t) and τk,l (t) respectively represent the magnitude, the phase and the arrival time associated with the kth ray within the lth cluster. Theoretically, all these parameters vary with time. Defining the PDP from a set of measurements according to equation [2.25], and assuming that the delay of each ray is approximately constant during the measurements, the Saleh and Valenzuela formalism yields the following formula: Ph (0, τ ) =

Kl L  

  2 βk,l δ τ − Tl − τk,l

[2.32]

l=1 k=1

As shown in Figure 2.8, the magnitude of the PDP rays generally follows a decay which is close to an exponential function. This exponential decay may be observed at both the cluster level and the ray level within a single cluster. The inter- and intra-cluster exponential decay constants, respectively denoted Γ and γ, are thus defined so that the magnitude of the rays obeys the following rule: 2 2 = β1.1 e− βk,l

Tl −T1 Γ

e−

τk,l γ

[2.33]

These constants may be retrieved from measurements by applying a linear least squares fitting procedure on the PDP represented in dB. 2.4.1.5. Cluster and ray arrival rates Without more accurate knowledge about the environment, it is generally assumed that ray arrivals correspond to independent events, and that the number of these events is dependent on the observation duration only. By

62

Ultra-Wideband Radio Propagation Channels

Power (mW)

IJk1

Cluster e-IJ/ī IJk2 IJk3

e-IJ/Ȗ e-IJ/Ȗ

T1

T2

e-IJ/Ȗ

T3

Delay (ns)

Figure 2.8. Power delay profile following the Saleh and Valenzuela formalism

definition, the ray – or cluster – arrivals may reasonably be regarded as a Poisson process. In the Saleh and Valenzuela formalism, it is thus proposed that the arrival probability for a new cluster or a new ray follows an exponential law, with respective parameters Λ and λ. Parameters Λ and λ are respectively called cluster and ray arrival rates, and the numbers Λ1 and λ1 represent the mean duration between two successive clusters or rays. These parameters are assessed by studying the inter-cluster and inter-ray duration distributions.

2.4.2. Propagation loss When expressed in dB, equation [2.3] corresponding to the Friis formula for free space propagation is written:  P L(f, d) = 20 log

4πf d c

 − GT (f ) − GR (f )

[2.34]

where P L(f, d) represents the ratio between the transmitted power and the received power. The slow variations of the propagation channel are mainly due to propagation loss and shadowing effect. For a practical channel, in order to

Radio Wave Propagation

63

characterize the double frequency and distance dependence of the path loss, the parameter P L(f, d) is approximated by the following formula:       f d + 10Nd log + S(f, d) [2.35] P L(f, d) = P L f0 , d0 + 10Nf log f0 d0 where f0 and d0 correspond to an arbitrary frequency and an arbitrary distance.4 Nf and Nd are called frequency and distance dependent path loss exponents. Parameter Nd accounts for the interactions between the radio wave and the environment, such as the transmission phenomenon or the waveguide effect, and can significantly differ from the theoretical value Nd = 2. Parameter Nf accounts for the frequency dependence of the propagation phenomena, and also includes the variations of the effective area for an ideal isotropic antenna. By considering the propagation channel without antennas in a LOS situation, this parameter should be close to its theoretical value Nf = 2. Some authors consider antennas as a part of the propagation channel; in this case, additional variations of the parameter Nf may be observed, which is linked to the measurement antenna gain. Finally, the term S(f, d) corresponds to the slow variations of the propagation channel. As the parameters Nf and Nd are calculated by linear regression, the parameter S(f, d) presents a zero average. When expressed in dB, this variable is generally considered as Gaussian, and it is characterized by its standard deviation σS . In order to calculate the parameter Nf from measurements, we introduce the power transfer function PT (f ), equivalent to the PDP Ph (0, τ ) in the frequency domain. This takes the average received power as a function of frequency for a number of locally measured transfer functions: PT (f ) =

M 2 1    T f, tm  M m=1

[2.36]

2.4.3. Fast fading The fast fading of the propagation channel corresponds to the magnitude fluctuations in the received signal. It may be assessed for a narrowband signal or for a given delay in the case of a wideband signal. Mathematically, it is characterized by the statistical law of the random variable |h(t, τ )| for a given τ . In practice, we study a set of samples |h(tm , τ )| corresponding to M measurements taken at close locations (or in a time-variant environment),

4. We may use the central frequency in the considered band for f0 , and the distance d0 is generally 1 m.

64

Ultra-Wideband Radio Propagation Channels

while verifying that the channel stationarity condition holds. The distributions generally used to assess fast fading include Rayleigh, Rice, Nakagami, Weibull, and log-normal laws (cf. Appendix B). In order to select a specific theoretical distribution, a goodness-of-fit test is employed, such as the Kolmogorov-Smirnov test (cf. Appendix B.2). Some useful tools also exist to characterize the temporal behavior of a signal. The level crossing rate consists of determining the frequency at which the signal magnitude decreases below a given threshold. The average fade duration is an estimate of the time during which the signal magnitude stays below a given threshold [PAR 00]. 2.4.4. Spectral analysis Another way to characterize temporal variations in the channel consists of studying the Doppler spectrum for the main impulse response paths. These spectra may be observed on the scattering function PS (τ, ν). In order to characterize the channel variations independently of the delay, we use the mean Doppler spectrum defined as: ∞ PS (τ, ν)dτ [2.37] PH (0, ν) = −∞

As in the PDP case, we may define the Doppler spread as:   ∞  2  ν − νm PH (0, ν)dν −∞  ∞ νRM S = P (0, ν)dν −∞ H where νm is the mean Doppler shift defined by: ∞ νPH (0, ν)dν νm = −∞ ∞ P (0, ν)dν −∞ H

[2.38]

[2.39]

As explained earlier (section 2.2.3.3), the Doppler spectrum is closely linked to the arrival direction of the multiple propagation paths. Parameters such as the angular spectrum may be used to characterize the signal’s departure and arrival directions. This is of particular interest for MIMO applications [COS 04]. 2.5. Conclusion In order to design and optimize wireless communication systems, an accurate knowledge of the radio propagation channel is required. The performance of a

Radio Wave Propagation

65

wireless transmission system is indeed dictated by the propagation conditions between the transmitter and the receiver. These devices need to be designed in order to benefit from the channel characteristics and to mitigate its negative effects. In this chapter, the propagation channel characteristics have been presented in terms of power attenuation and multipath propagation. The spatial and frequency selectivity concepts as well as the Doppler effect were introduced. Multipath propagation may be regarded as a filter causing a distortion and a temporal variation to the transmitted signal. A mathematical framework was presented in order to describe both deterministic and random channels. For this, the particular case of WSSUS channels has been thoroughly discussed. A number of parameters are available to characterize the propagation phenomena. We generally model the propagation loss with respect to frequency and distance, the channel impulse response’s general shape and its variations in terms of fast fading. The physical concepts and mathematical tools presented in this chapter will serve as a basis to describe the simulation and modeling techniques detailed in Chapters 4 and 5.

This page intentionally left blank

Chapter 3

UWB Propagation Channel Sounding

3.1. Introduction Experimental characterization of the radio channel requires the analysis of a large number of propagation measurements. In order to set up a measurement campaign, a large number of sounding techniques are available [GUI 99]. Selecting one method or the other depends on the measurement environment, on the observed frequency band, and on the acquisition speed constraints. Sounding UWB channels raises some particular issues, which are developed in this chapter. The different sounding methods for wideband channels are then exposed, by distinguishing between frequency domain and time domain techniques. In order to observe the UWB channel fluctuations in more detail, it is necessary to employ a real time measurement technique. For this purpose, we present an advanced sounding technique, exploiting the performances of a wideband, single-input multiple-output (SIMO) sounder. The end of the chapter illustrates the different channel sounding techniques by presenting a few measurement campaigns. First, the most significant UWB channel measurement campaigns are listed. For each experiment, the equipment and the measurement conditions are described. We then present the setting up of a sounding campaign through a few examples. 3.2. Specificity of UWB channel sounding The purpose of channel sounding is to measure the impulse response h(t, τ ) linking the received signal s(t) to the transmitted signal e(t) through

68

Ultra-Wideband Radio Propagation Channels

Delay (ns)

Relative magnitude (dB)

Sounder impulse response

Relative magnitude (dB)

Relative magnitude (dB)

a filtering operation (see equation [2.9]). Such measurements characterize both the frequency selectivity and the time variability of the channel. In practice, there is no inverse convolution operation available, that would allow for the extraction of the impulse response from arbitrary signals e(t) and s(t). However, a number of techniques using specific exciting signals e(t) may be used, where the impulse response is obtained by processing the signals e(t) and s(t). The transmitted signal needs to fulfill some properties depending on the method used for calculating the impulse response. Channel impulse response over an infinite bandwidth

Delay (ns)

Convolution

Unresolved path

Measured impulse response

Delay (ns)

Figure 3.1. Time resolution of a wideband sounder

The main characteristics of a wideband sounder are the following: • Analyzed bandwidth: the analyzed bandwidth corresponds to the frequency band over which the impulse response is estimated. It generally corresponds to the bandwidth of the transmitted probe signal. Propagation channel measurements over bandwidths in the order of 100 MHz is well supported by the currently available sounders [GUI 99]. In the case of UWB signals, the bandwidth of several GHz may represent a challenge for channel measurements. • Time resolution: the time resolution characterizes the sounder’s capability to distinguish between two paths with very close delays. The impulse response estimated by the sounder corresponds to a convolution

UWB Propagation Channel Sounding

69

between the channel impulse response over an infinite bandwidth and the sounder’s impulse response over the analyzed band (see Figure 3.1). The latter may be obtained by directly cable-connecting the transmitter and the receiver. The time resolution is generally defined as half the width of the sounder impulse response peak. As an approximation, it may also be defined as the inverse of the analyzed bandwidth. In order to avoid the shadowing of some paths by the side lobes of the sounder impulse response, a weighting window may be applied [HAR 78]. Such a window is selected as a compromise between the level of the side lobes and the width of the main lobe. • Maximum Doppler shift: when the propagation channel varies with time, we can measure its frequency dispersion by studying its Doppler spectrum (see section 2.4.4). For this purpose, the sounder needs to be able to quickly measure successive impulse responses. The measurement repetition duration ΔT (meas) is defined as the duration separating two successive channel measurements. It encompasses the measurement acquisition duration t(meas) and some time for data processing and storage. It is then possible to measure a maximum absolute (meas) 1 . However, it should be noted that during the Doppler shift νmax = 2ΔT (meas) measurement of a single impulse response, the channel should be considered as static. Thus, a sounder capable of measuring the time varying channel needs to present a very low acquisition duration t(meas) . • Dynamic and length of the channel impulse response: the impulse response dynamic corresponds to the power ratio between the maximum impulse response and the noise level. A high dynamic allows the sounder to detect strongly attenuated paths. The length of the channel’s impulse response corresponds to the maximum delay that can be measured. In the case of the UWB propagation channel, the time resolution is generally high, due to the wide analyzed bandwidth. Consequently, developing UWB sounders with a low measurement duration is a challenging task. Some constraints are common in UWB channels, because of the wide measured frequency band. Over an analyzed bandwidth of several GHz, the behavior of the sounding equipment may vary strongly, and this needs to be accounted for in the measurement process. In particular, the antennas characteristics need to be stable across the measured frequency band. Narrowband antennas (dipoles, horns, etc.) and dispersive wideband antennas (spiral and log-periodical antennas, etc.) may thus not be used for this purpose [SCH 03a]. In practice, biconical, monoconical or planar UWB antennas are

70

Ultra-Wideband Radio Propagation Channels

used. Some examples of these antennas are given in Figure 3.2. In any case, it is necessary to properly characterize the antennas used for the measurement [SIB 04]. The properties of some other pieces of equipment, such as cables or amplifiers, may also vary in frequency, and it is important to characterize each item accurately before the measurement. Monoconical antenna

Bowtie planar antenna

Ideal biconical antenna

Biconical antenna

Figure 3.2. UWB measurement antennas

Finally, a UWB receiver is sensitive to any radio emission at frequencies near or within the analyzed frequency band. Before the measurement starts, we need to make sure that the analyzed radio spectrum is free of any jamming from external systems. Out-of-band emissions, such as the GSM and WiFi signals, should also be filtered. This can be done using a high-pass filter. This filter should be taken into account during the calibration phase in order not to affect the measured signal.

3.3. Measurement techniques for UWB channel sounding This section presents the main UWB radio channel measurement methods: frequency domain methods and time domain methods. For each method, the basic principles are presented, and the advantages and drawbacks of this method are detailed. We finally present an innovative hybrid method for the real time measurement of UWB channels.

UWB Propagation Channel Sounding

71

3.3.1. Frequency domain techniques The frequency domain method is the most commonly used UWB channel sounding technique, on account of its ease of implementation. It consists of sampling the channel transfer function T (f, t). This is done by transmitting a narrowband signal at a fixed frequency, and by measuring the attenuation and the relative phase of the received signal [GUI 99]. In practice, the analyzed band is divided into N samples separated by a frequency step Δf (meas) . The impulse response is obtained using an inverse Fourier transform along the frequency axis. The obtained time resolution1 is: (meas)

Rt

=

1 N Δf (meas)

[3.1]

and the length of the channel impulse response is: (meas) τmax =

N −1 N Δf (meas)

[3.2]

3.3.1.1. Vector network analyzer The tool best suited to characterizing the channel using a frequency sweeping method is the vector network analyzer (VNA). This device is generally used to characterize high frequency quadripoles through the measurement of S-parameters. For the purpose of channel sounding, port 1 is connected to the transmitting antenna and port 2 is connected to the receiving antenna. The channel transfer function is derived from parameter S21 (f ). In general, a sine signal is used to sweep the analyzed band. The received signal is down-converted towards an intermediate frequency (IF), where it is pass-band filtered around a fixed frequency and analyzed. Hence, this device is capable of sweeping a very wide frequency band. Using narrowband filters at the receiver leads to a very good measurement dynamic, but also increases the overall measurement duration. In addition, the measurement of the transfer function phase requires a very good synchronization between the local oscillators (LO) at the transmitter and at the receiver. Figure 3.3 gives a schematic view of this device.

1. This time resolution is calculated without applying any frequency domain windowing.

72

Ultra-Wideband Radio Propagation Channels

Propagation channel

Reference signal LO

LO

S21 measurement at IF Analysis and storage

Figure 3.3. Propagation measurement using a frequency domain sounder

This technique offers advantages in terms of bandwidth and dynamic. As a result, it has been frequently used for the purpose of UWB channel sounding [GUN 00, OPS 01, GHA 02a, CHE 02, KEI 02, HOV 02, KUN 02a, GHA 03b, BUE 03, DAB 03, ALV 03, CHA 04, SCH 04, BAL 04a, KAR 04b, JAM 04, CHO 04b, CAS 04a, HAN 05]. However, the measurement duration is proportional to the number of measured frequency tones. For an analyzed bandwidth of several GHz, the measurement duration is in the order of 10 seconds. Hence, this technique cannot be used for time varying channels. When conducting VNA-based measurements, we should thus ensure that the environment remains static for the measurement duration. In addition, the distance from transmitter to receiver is limited to approximately 20 m, due to power attenuation in the feeding cables. 3.3.1.2. Chirp sounder A chirp sounder is a frequency domain method providing a solution to the issue of acquisition duration. Indeed, the sounding signal is no longer a pure sine wave, but a frequency chirp. Such a signal is generated using digital frequency synthesis components [COS 04].

UWB Propagation Channel Sounding

73

This frequency chirp may be characterized by the sequence duration Tc and the covered frequency range Bc , as illustrated in Figure 3.4. For a Bc Tc product larger than 100, over 98% of the energy is confined in the analyzed bandwidth Bc . The channel impulse response may be calculated either by matched filtering or using a heterodyne receiver and a low-pass filter. In the first case, the impulse response of the matched filter corresponds to a time reversed version of the emitted chirp signal [ART 95]. The channel impulse response is directly obtained at the output of the matched filter. In the case of a heterodyne reception, the output of the low-pass filter provides the channel transfer function, represented on a compact frequency band. Its bandwidth depends on the parameters Bc and Tc [COS 04]. The signal acquisition may thus be performed at a reduced sampling frequency. However, generating a chirp signal with a bandwidth larger than a few hundred MHz is still a challenging task. For this reason, chirp sounders have not yet been used for UWB channel sounding.

Magnitude

Bc

Bc Magnitude

Tc

Frequency

Tc

Time

Time

> 98% energy Frequency

Figure 3.4. Chirp signal

3.3.2. Time domain techniques The common characteristic of all time domain techniques is the use of a wideband excitation signal at the emitter. This way, the receiver processes the whole frequency band simultaneously, which drastically reduces the measurement duration. This section presents the most common time domain methods, and in particular those that have been used for UWB channel sounding. 3.3.2.1. Pulsed techniques The pulsed technique is mathematically the most straightforward time domain measurement method. Indeed, if the transmitted signal e(t) corresponds to a Dirac pulse, the received signal s(t) is directly proportional to the channel impulse response h(t, τ ). However, such a Dirac pulse would present an infinite flat spectrum and is not physically implementable. In

74

Ultra-Wideband Radio Propagation Channels

practice, we use pulse generators enabling the emission of short signals with a duration Δt in the order of 100 picoseconds. Denoting by ΠΔt (t) the emitted pulse, the received signal is given by: s(t) = h(t, τ ) ⊗ ΠΔt (t)

[3.3]

and represents a close approximation of the channel impulse response. At the receiver, a very fast acquisition of the signal is necessary. A digital sampling oscilloscope (DSO) is generally used, with sampling rates up to 20 Gsamples.s-1 . Other types of receivers are also implemented: for instance, a correlation receiver has been developed by the company Time Domain [YAN 02]. This technique is particularly interesting for the measurement of UWB channels. Indeed, pulse generators capable of emitting directly in the FCC frequency band (3.1–10.6 GHz) are now available. Generally, UWB sounders based on this principle do not require an up-converter stage, which simplifies the experimental setup. It should be noted, though, that the signals synthesized by the current pulse generators are limited to a maximum bandwidth of 1–2 GHz, with an upper frequency limited to 5 GHz. Hence, only parts of the FCC band may be measured using a direct pulse generator technique. In order to sound the upper part of the FCC spectrum, it is possible to add an up-converter stage, composed of an LO and a mixer at both the transmitter and the receiver. This solution is presented as a dashed line in Figure 3.5. The main advantage of the pulsed sounding technique is its low acquisition duration, the channel impulse response being recorded in real time. This technique should thus be selected for the measurement of space or time channel variations. However, this method also presents a number of drawbacks. Firstly, generating short duration pulses requires the amplifiers to deliver a high power directly followed by idle periods. The resulting low average power leads to a poor signal to noise ratio, and this method is not suited to large distances in NLOS configurations. Secondly, the power dynamic at the amplifier stage does not allow for an accurate control of the pulse shape. Finally, this technique requires a perfect synchronization between the emitter and the receiver, which may be solved by connecting the terminals using a cable. The attractive simplicity of this solution led a number of scientists to use this method for UWB channel sounding, but with a sounded frequency band generally below the FCC band [WIN 97a, WIN 97b, GUN 00, OPS 01, CHE 02, YAN 02, TER 03, LI 03]. Two measurement programs have been established using this technique within the 3.1–10.6 GHz band [PEN 02, BUE 03].

UWB Propagation Channel Sounding

75

Propagation channel

Reference signal LO

LO

0° 90°

I Pulse generator

Synchronization

Q DSO

Analysis and storage

Figure 3.5. Propagation measurement using a pulsed technique

3.3.2.2. Correlation measurements A possible way to increase the signal to noise ratio at the receiver is to use the autocorrelation properties of pseudo-noise (PN) sequences. Let Ree (t) and Res (t) respectively denote the input signal autocorrelation and the correlation function of the input signal e(t) with the output signal s(t). According to the convolution and correlation function properties, these functions are also linked by a convolution equation: Res (t) = h(t, τ ) ⊗ Ree (t)

[3.4]

If the input signal is close to a white noise, its autocorrelation function is close to a Dirac pulse. In this case, the identification problem is similar to the one occurring in the pulsed technique. In practice, we use maximum length PN sequences, also called m-sequences. This corresponds to a good approximation of a colored noise with zero mean and limited bandwidth. An m-sequence may

76

Ultra-Wideband Radio Propagation Channels

be generated using a shift register with m bits and an adder, which results in a sequence of length 2m − 1. Its autocorrelation function presents a theoretical dynamic of 20 log(2m − 1) dB. In the frequency domain, the −3 dB analyzed bandwidth is equal to the clock frequency fc used at the PN sequence generator. At the transmitter, a correlation sounder is thus composed of a PN sequence generator and an up-converter stage towards the working frequency. Typically, wideband correlation sounders transmit signals in the order of 100 MHz. For UWB channel sounding, the frequency band may be widened by increasing the clock frequency, but the sounder implementation becomes more complex. The University of Ilmenau, Germany, presented a MIMO UWB sounder working in the 0.8–5 GHz frequency band [SAC 02]. For this purpose, an integrated circuit shift register has been specifically developed. At the receiver, once the received signal has been down-converted in baseband, several acquisition techniques may be used. The first consists of using an analog filter matching the transmitted PN sequence. This principle enables the measurement of the impulse response in real time. However, the analyzed bandwidth is limited by the passband of the filter, and the measurement dynamic is low. Another technique consists of sampling the received signal and computing the convolution function using digital filters. The maximum analyzed bandwidth is then limited by the speed of the analog-to-digital converters. This solution is presented in Figure 3.6. It has been used by the University of Rome “Tor Vergata”, Italy, to sound the 3.6–6 GHz band [DUR 04]. The receiver was simply composed of a DSO. Time domain correlation sounders present the advantages of a high impulse response dynamic, and a possible functioning in real time. Their implementation is however complex, and the quality of the measured impulse response largely depends on the performance of the sounder components. In particular, an accurate synchronization between the transmitter and the receiver is necessary. This may be achieved using a stable reference (e.g. a rubidium oscillator) or a direct cable connection between the two terminals. Sliding correlation technique The sliding correlation sounder is a similar technique that proceeds the convolution operation in the analog domain while increasing the measurement dynamic. The convolution is performed using a replica of the original PN sequence with a clock frequency fc2 slightly different from the initial clock frequency fc1 . This leads to a time domain sliding of the PN sequences with respect to each other. Hence, using an integrator, one point of the correlation

UWB Propagation Channel Sounding

77

Propagation channel

Reference signal 0° OL

OL

90°

I Arbitrary sequence generator (e.g. shift register)

Synchronization

Analysis and storage

Q

Fast acquisition

Correlation or inversion

Figure 3.6. Propagation measurement using a PN sequence. The illustrated acquisition technique consists of digitizing the received signal prior to convolution processing

function between the transmitted signal and the received signal is calculated at each instant. c1 in The obtained impulse response is expanded by a ratio k = fc2f−f c1 the time domain and compressed by a ratio k in the frequency domain. This compression enables the use of narrower filters at the receiver, which improves the dynamic. In addition, a lower sampling rate may be used for the analog-to-digital conversion.

This technique has been used by the University of Kyoto Sangyo (Japan) to develop a UWB sounder operating in the 5.5–8.5 GHz frequency band [TAK 01]. The main drawback of this technique is the duration of the impulse response calculation, which precludes any Doppler analysis of fast time varying channels.

78

Ultra-Wideband Radio Propagation Channels

3.3.2.3. Inversion techniques Inversion techniques are based on the transmission of an arbitrary sequence and are thus similar to correlation sounding techniques (see Figure 3.6). The main difference lies in the impulse response estimation, which is performed using an estimation filter. Filtering is generally applied in the digital domain after the acquisition of the analog signal. The used filter minimizes the squared error between the impulse response and the estimated response. In particular, such a filter accounts for the imperfections of the measurement device. The inversion technique is notably used in the sounder developed at France Telecom Research and Development [CON 03]. It uses a Wiener filter, with a frequency spectrum given by: GWiener (f ) =

E ∗ (f )I ∗ (f ) |E(f )I(f )|2 + α

[3.5]

where E(f ) represents the transmitted signal spectrum, I(f ) represents the sounder response spectrum, and α is a non-zero constant linked to the signal to noise ratio [BAR 95]. As a main advantage, the inversion technique improves the impulse response calculation by accounting for the imperfections of the sounder components. The used PN sequence is optimized in order to spread over a wide band with a relatively constant envelope. The limitations of this technique are directly linked to the performances of the digital-to-analog and analog-to-digital converters. In particular, the analyzed bandwidth is in the order of a few hundred MHz. For the sake of comparison, Table 3.1 presents the main advantages and drawbacks of the presented frequency domain and time domain techniques. 3.3.3. Multiple-band time domain sounder for dynamic channels Classical frequency or time domain sounding techniques are not intrinsically well adapted to the measurement of time varying UWB channels. On the one hand, frequency domain techniques lead to a long measurement duration. On the other hand, time domain techniques are fast enough to enable the measurement of time varying channels, but their implementation within the FCC band is challenging. This section presents a hybrid solution consisting of using a wideband time domain sounder and successively measuring several adjacent partial bands. This principle was initially exploited by the University of Kassel (Germany). They developed a sounder capable of measuring a channel of 600 MHz divided into 10 partial bands of 60 MHz, with a measurement

Frequency

Time

significant

Correlation

significant

low

Pulsed

Inversion

significant

Chirp

high

very high

VNA

Sliding correlation

Dynamic

Technique easy

complex

complex

easy

For practically implemented solutions.

500 MHz–1 GHz (limited complex by DAC and acquisition)

1–3 GHz (limited by clock frequency)

1–5 GHz (limited by clock frequency and acquisition)

1–2 GHz (limited by pulse generator)

no experiment

marginal

marginal

frequent out of FCC band

no experiment

frequent (static channel)

Implemen- Use for UWB tation sounding

100–300 MHz (limited by complex signal generation)

10 GHz and above (limited by the measurement duration)

Maximum bandwidth a

Table 3.1. Comparison of the different sounding techniques

a

possible

possible for low Doppler spreads

possible

possible

possible for low Doppler spreads

impossible

Doppler analysis

UWB Propagation Channel Sounding 79

80

Ultra-Wideband Radio Propagation Channels

repetition duration of 300 μs [KAT 00]. In the following, we present the different issues linked to the development of such a sounder, and we illustrate how it can be implemented on the basis of a wideband SIMO sounder [PAJ 03]. 3.3.3.1. Principle of multiple-band time domain sounding The technique of multiple-band time domain sounding exploits the performance of a time domain sounder, such as the sounder developed by France Telecom Research & Development. In its standard version, this sounder allows for the measurement of 250 MHz frequency bands. At the up-converter stage, an LO signal is responsible for the up-conversion of the transmitted sequence towards the analyzed band. By appropriately driving this LO signal, it is possible to sound several adjacent bands. The different challenges are the following: • Analyzed band: the number of measured partial bands determines the width of the global analyzed band. At both the transmitter the receiver, the global analyzed band needs to be filtered and cleared from any interfering signal, such as the LO signal and its harmonics. • Measurement repetition duration: in an indoor configuration, the maximum speed of mobile terminals is about 2 m.s−1 . Considering an extreme case, i.e. a mobile terminal and a maximum frequency of 10.6 GHz, the maximum Doppler shift is λv = 70 Hz. This maximum Doppler shift increases to 2v λ = 140 Hz if we consider mobile scatterers, taking into account the paths with one reflection as significant paths. Thus, to characterize time varying channels, the equipment has to sample the channel every 3.5 ms. This time includes the necessary switching from one band to another, which needs to be synchronized with the transmitted sequence. • Calibration: when measuring adjacent bands, a simple process needs to be set up for an accurate calibration of the sounder in terms of phase, magnitude and absolute delay, for each of the adjacent bands. • Measurement dynamic: when working as a multiple-band sounder, the dynamic performance of the original wideband sounder needs to be preserved, in order to obtain a reliable result. These different issues are similar to those occurring when characterizing the wideband channel with multiple antennas at the receiver, in a SIMO configuration. A SIMO sounder may thus be easily adapted to perform multiple-band time domain sounding. For a better understanding, the next section reviews the general structure of the SIMO sounder available at France Telecom. A further description of this sounder is available in [CON 03].

UWB Propagation Channel Sounding

81

3.3.3.2. Description of the SIMO channel sounder The sounder developed at France Telecom Research & Development is a time domain sounder allowing for radio channel measurement over different frequency bands between 2 GHz and 60 GHz. The sounding method is the Wiener inversion technique, applied on a PN sequence exhibiting a flat spectrum over the analyzed bandwidth. For frequency bands below 17 GHz, a multiple sensor mode enables the simultaneous measurement of the radio channel over 10 receiving antennas. In terms of performance, the sensitivity of this sounder is about −85 dBm. The impulse response dynamic depends on the length of the PN sequence, the signal to noise ratio at the sounder input, and the oscillator phase noise. For a received signal of about −60 dBm over a band of 250 MHz around 5 GHz and a sequence of 8192 samples, the measurement dynamic is larger than 40 dB. Figure 3.7 presents a simplified block diagram of the receiver. To repeat the measurement as quickly as possible, a fast switch selects the following antenna every other sequence. The first PN sequence is used for the measurement, while the antennas switch during the next PN sequence. The signal is then amplified using a wideband (3–18 GHz) low noise amplifier (LNA). It is then pass-band filtered around the RF carrier frequency. A first down-converter stage driven by an external frequency synthesizer displaces the signal around an IF at 1.5 GHz. Automatic gain control (AGC) is then applied using variable attenuators to compensate for the power variations in the received signal. AGC is regularly performed, before the measurement of the signal received by the different sensors. Thus, the AGC duration limits the measurement repetition duration. In a traditional configuration with 10 antennas, the minimum repetition duration is about 1.2 ms. A second down-converter stage displaces the signal around a second IF at 250 MHz. The received signal is then sampled using an analog-to-digital converter (ADC) at a sampling rate of 1 Gsample.s−1 . We may note that the transmitter and the receiver use the same IF at 1.5 GHz. Thus, the LO frequency is the same for the external synthesizers at the transmitter and the receiver. All LO are synchronized using a reference rubidium at 10 MHz. 3.3.3.3. Extension towards UWB In order to perform measurements over adjacent frequency bands, it is necessary to modify the LO frequency at the transmitter and at the receiver. Traditional oscillators present a locking time in the order of 10–50 ms. This transition duration is mainly due to the positioning duration of the internal phase locked loop, and cannot be reduced. Directly driving a single external synthesizer thus leads to a total measurement duration in the order of 40–200 ms for an analyzed band of 1 GHz. Taking into account the constraints

Ultra-Wideband Radio Propagation Channels

Fast switch 10 1

82

RF

LNA

A External synthesizer

AGC

1.5

250 D MHz

GHz

LO

Figure 3.7. Receiver block diagram

linked to real time measurements (see section 3.3.3.1), this solution cannot be used. The extension of the SIMO sounder towards a real time UWB sounder exploits the duality between multiple-input measurements and multiple-band measurements. The main idea is to reuse the fast antenna switching module, in order to switch between the carrier frequencies of each partial band to be measured. A practical implementation of this concept is presented in Figure 3.8. As can be seen, the input connector is now directly connected with the LNA, and a single antenna is available. The sounder is thus in a single-input single-output (SISO) measurement configuration. The fast switching module is used to sequentially feed the mixer of the first down-converter stage with one of the 10 LO signals (f1 to f10 ) in turn. These signals are generated by external synthesizers and tuned so that the receiver actually sweeps the selected partial bands. As each synthesizer is locked at a fixed frequency, no delay is experienced for the locking of the LO frequency. In this configuration, the sounder is capable of sweeping up to 10 partial bands of 250 MHz each. Hence, UWB measurements are theoretically possible up to a bandwidth of 2.5 GHz. On account of its development concept, this sounder fulfills most of the required criteria for real time UWB channel measurement. Indeed, the multiple-input architecture is directly used for the measurement over multiple bands. For the calibration of each partial band in terms of phase, magnitude

UWB Propagation Channel Sounding

External synthesizers

f10 Towards the emitter up-converter

Fast switch 10 1

f1

LNA

A

83

AGC

1.5

250 D MHz

GHz

LO

Figure 3.8. Block diagram of the modified receiver with UWB extension

and delay, the procedure used in the SIMO configuration is still valid. In addition, regarding the fast switching of partial bands, the overall switching time through all partial bands may be as low as 1.2 ms, which allows for the measurement of channel variations with a maximum Doppler shift of 416 Hz. In the original version of the SIMO sounder, the filter preceding the first down-converter stage was only a few hundred MHz wide to reject undesirable signals and reduce the noise level. The same type of filtering was performed at the emitter. In the UWB configuration, however, the sounded frequency band needs to be filtered by one single pass-band filter, in order to avoid unnecessary filter switching. In its current version, the UWB sounder is equipped with filters of 1 GHz bandwidth. Unlike the SIMO channel sounding case, UWB measurements using the sweeping method necessitates a periodical modification of the emitted signal central frequency. For this reason, the frequency switch performed at the receiver and at the transmitter need to be perfectly synchronized. To solve this problem, the same LO signal may be used to feed both the receiver down-converter and the transmitter up-converter stages. The main drawback of this solution is that the transmitter and the receiver need to be cable connected. However, in most indoor configurations, this connection is realizable using a cable of acceptable length. Advantageously, this solution allows us to use only one set of external synthesizer, which considerably reduces the global cost of the equipment.

84

Ultra-Wideband Radio Propagation Channels

3.3.3.4. Experimental validation The modifications presented above have been applied to the sounder developed by France Telecom for its extension to real time UWB measurements. To sweep the 5–6 GHz frequency band, 5 external synthesizers have been connected to the fast switching module. In this configuration, the impulse response dynamic was measured at 40 dB. Using 5 partial bands, the minimum measurement repetition duration is about 1 ms and the actual measurement duration is 20.5 μs. With its 256 MB memory, the acquisition card is able to sound the time varying UWB channel for a duration of 80 s in standard conditions (bandwidth of 1 GHz and observable Doppler spread of 150 Hz). Figure 3.9 presents the results obtained during a real time radio channel measurement in a dynamic environment. During this experiment, the transmitting antenna was fixed and the receiving antenna was held by a moving person. This configuration corresponds to the practical situation where a user with a mobile terminal walks in the proximity of a fixed access point. 0 (a) 2

-5

(b)

Distance-delay (m)

6

-15 (c)

8

-20

10

-25

(d)

12 -30 14

Relative attenuation (dB)

-10

4

-35 16

(e) -40

18 0

2

4

6 Time (s)

8

10

12

-45

Figure 3.9. Time varying impulse response in a dynamic environment

The impulse response represented in Figure 3.9 corresponds to a 12.5 s record of the signal obtained at the receiving antenna moving during the experiment. Acquisitions were performed every 10 ms. For ease of

UWB Propagation Channel Sounding

85

interpretation, the path delay on the y-axis has been converted to path length in meters. In the first part of the trajectory (between t = 0 s and t = 7 s), the person is moving towards the emitter antenna, reducing its relative distance from 6 m to 2 m. Hence, we can observe a main path with increasing power (a). In the second part of the trajectory (between t = 7 s and t = 11 s), the person is moving away from the transmitter antenna, partially obstructing the line of sight. This explains the shadowing experienced by the shortest path (b). In this part of the curve, three other main paths are observable, one with increasing length (c) and two with decreasing lengths (d, e). These two last paths might correspond to echoes transmitted via a reflection on a wall opposite the transmitter location. This feasibility study shows that it is possible to develop the UWB channel sounder by applying minor modifications to a wideband SIMO sounder. By exploiting the duality between multiple inputs and multiple bands, most of the SIMO-capable sounders could be extended towards UWB channel sounding. The prototype presented here allows for the measurement of UWB channels over a band of 1 GHz with a dynamic of 40 dB. 3.4. UWB measurement campaigns 3.4.1. Overview of UWB measurement campaigns A number of UWB radio channel measurement campaigns were cited in this chapter. These diverse campaigns used different sounding techniques, but also differ in the measured frequency band, the type of environment, the antennas used and the measurement set-up. In order to compare the analysis results from these experiments, it is necessary to recall the conditions of each campaign. Table 3.2 summarizes the inventoried UWB measurement campaigns and provides some useful information for each of them. Among the first UWB studies, the UltRaLab laboratory from the University of South California undertook two measurement programs in 1997, but most UWB experiments started from the year 2000 onwards. Most measurement programs used the VNA frequency domain method. Other experimental set-ups are based on a time domain method, using pulses or PN sequences. Different indoor environments, such as the office or residential environments, and some outdoor environments (forest, urban) were sounded. We may also note some original experiments, on a metal ship or in an industrial environment. Finally, regarding the analyzed band, only seven measurement campaigns cover the entire FCC band [KUN 02a, BUE 03, ALV 03, CAS 04c, KAR 04b, HAN 05, PAG 06b]. Within the FCC band, three experiments only permitted real time UWB measurements [PEN 02, CAS 03, PAG 06a].

Pulse generator and DSO

Pulse generator and DSO; VNA; Pulse generator and correlation receiver

Pulse generator and DSO; VNA

1997 [WIN 97a, WIN 97b]

UltRaLab

UltRaLab SS 2000 [GUN 00] Curtis

Stanford University

Pulse generator and DSO; VNA

Intel Labs

2002 [CHE 02]

VNA

AT&T Labs - 2002 [GHA 02a, MIT GHA 03c]

2001 [OPS 01]

Sounding method

Measurement Date Reference campaign

Spatial configuration

Office; laboratory

Metal ship

LOS/ — NLOS

LOS/ — NLOS

LOS/ — NLOS

Forest; office LOS/ 49 locations NLOS on a 90 cm × 90 cm grid

4.375– Residential 5.625 GHz, with 3.1 MHz step

1–1.8 GHz, with 2 MHz step

700–1.8 GHz, with 1 MHz step

Width >1 GHz

Analyzed band Environment Link

Biconical 2–8 GHz, with Residential; LOS/ Two antennas (MEC) 3.75 MHz step office NLOS perpendicular and discone positioners antennas (length 25 cm) (Pulsicom with 20 Technol.) locations

Monoconical omnidirectional antennas

Wideband antennas

Patch diamond dipoles

Patch diamond dipoles

Antennas

86 Ultra-Wideband Radio Propagation Channels

VNA

VNA

VNA

VNA

2002 [YAN 02]

2002 [KEI 02, KEI 03]

Time Domain Corporation (correlator)

UCAN CEA LETI

Ultrawaves - 2002 [HOV 02] Oulu University

Whyless.com 2002 [KUN 02a]

AT&T WINLAB

2003 [GHA 03b]

Pulse generator and DSO

2002 [PEN 02]

Time Domain Corporation (DSO)

Pulse generator and correlation receiver [WIT 99]

Sounding method

Measurement Date Reference campaign

Analyzed band Environment Link

Spatial configuration

NLOS —

1–11 GHz, Office with 6.25 MHz step

LOS/ 4500 locations NLOS on a 149 cm × 29 cm grid

LOS/ — NLOS

Omnidirectional 2–8 GHz, with Residential; LOS/ 25 locations monoconical 3.75 MHz step shopping NLOS on a 20 cm × antennas center 20 cm grid

Biconical antennas (ETH Z¨ urich)

Omnidirectional 2–8 GHz, with Office monoconical 3.75 MHz step antennas (CMA118/A)

Omnidirectional 2–3 GHz, with Residential; LOS/ 100 locations monoconical 2.5 MHz step office NLOS on a 90 cm × antennas 90 cm grid (CMA118/A)

Omnidirectional Width Office antennas >1.5 GHz around 2 GHz

Omnidirectional 3–5 GHz, with Residential; LOS/ — antennas 3.75 MHz step office NLOS

Antennas

UWB Propagation Channel Sounding 87

Pulse generator and DSO

2003 [TER 03]

2003 [PAG 03]

2003 [LI 03]

CNAM Thales

France Telecom R&D

Hong Kong University

VNA

2003 [DAB 03]

2003 [ALV 03]

New Jersey Instit. of Tech.

UCAN Cantabria University

VNA

Pulse generator and DSO; VNA

NETEX 2003 [BUE 03, Virginia Tech BAY 04]

Pulse generator and DSO

VNA

Sounding method

Measurement Date Reference campaign Corridor

Office; laboratory

Office

Omnidirectional 1–13 GHz, Office; monoconical with 2.5 MHz laboratory antennas step (EM6865)

Omnidirectional 2–6 GHz monoconical antennas and log-periodical antennas

Omnidirectional 100–12 GHz biconical antennas and TEM horns

Office; laboratory; meeting room

4–6 GHz, with Office 2 MHz step

0–3 GHz

—

Spatial configuration

—

LOS/ 9 locations on NLOS a 6 cm × 6 cm grid

LOS

LOS/ 49 locations NLOS on a 90 cm × 90 cm grid

LOS/ x-positioner NLOS (length 120 cm) with 61 locations

LOS/ 60 locations NLOS on a rotating arm (27 cm radius)

LOS

Analyzed band Environment Link

Omnidirectional 1.2–1.8 GHz dipole

Patch omnidirectional antennas

Wideband antennas

Antennas

88 Ultra-Wideband Radio Propagation Channels

PN sequence and DSO; VNA; PN sequence and correlation receiver

VNA

Ultrawaves - 2003 [CAS 03, Rome Tor CAS 04c] Vergata University

2004 [CHA 04]

2004 [SCH 04]

2004 [BAL 04a]

2004 [KAR 04b]

Chiao-Tung University

ETH Z¨ urich

Instit. for Infocomm Research

Lund University

VNA

VNA

VNA

Sounding method

Measurement Date Reference campaign Office; laboratory

2–8 GHz, with Corridor; 1.875 MHz lobby step

3–5 GHz, with Office 2.5 MHz step

3.6–6 GHz; 2–12 GHz, with 5 MHz step

Omnidirectional 3.1–10.6 GHz, Industrial monoconical with 6 MHz antennas step

Spatial configuration

LOS/ Two NLOS x-positioners (transmitter/ receiver) with 7 locations along 30 cm

LOS/ 9 or 49 NLOS locations on a 10 cm × 10 cm or 30 cm × 30 cm grid

LOS/ 45 locations NLOS on a 28 cm × 56 cm grid

LOS/ 64 locations NLOS on a 26 cm × 26 cm grid

LOS/ 625 locations NLOS on a 48 cm × 48 cm grid; 73 positions on a non-uniform grid

Analyzed band Environment Link

Omnidirectional 3–6 GHz, with Urban; conical antennas 1.875 MHz office step

Planar omnidirectional antennas (Skycross)

Not communicated

Omnidirectional monoconical antennas (EM6865); prototype antennas (ENSTA)

Antennas

UWB Propagation Channel Sounding 89

VNA

2004 [JAM 04]

2004 [CHO 04b]

Oulu University

Samsung

VNA

2005 [PAG 06b]

2005 [PAG 06a]

France Telecom R&D

France Telecom R&D

Residential

LOS/ 25 locations NLOS on a 60 cm × 60 cm grid

Omnidirectional 4–5 GHz, with Office monoconical 2 MHz step corridor antennas

LOS

—

LOS/ 90 locations NLOS on a rotating arm (20 cm radius)

3.1–10.6 GHz, Residential; LOS/ Up to 10 × 10 with 10 MHz office NLOS × 7 locations step at transmitter and receiver

3–10 GHz, with 4.375 MHz step

Omnidirectional 3.1–11.1 GHz, Office monoconical with 2 MHz antennas step

Monopoles and biconical antennas

Planar dipoles

Spatial configuration

LOS/ x-positioner quasi- with 7.9 mm NLOS step

Analyzed band Environment Link

Omnidirectional 0.5–10 GHz, Office monoconical with 6.25 MHz antennas step (CMA118/A)

Antennas

Table 3.2. UWB propagation channel measurement campaigns

Multiple-band time domain sounder

VNA

Tokyo Instit. 2004 [TSU 04, of Tech. HAN 05]

VNA

Sounding method

Measurement Date Reference campaign

90 Ultra-Wideband Radio Propagation Channels

UWB Propagation Channel Sounding

91

3.4.2. Illustration of channel sounding experiments The previous study of the different UWB channel sounding techniques shows that the frequency domain technique using a VNA is the only available method that enables a full characterization over the whole FCC band. In the following, two measurement campaigns using this method are presented. The first campaign covers the 3.1–10.6 GHz band [PAG 06b], and the second one covers the 2–6 GHz band. A third campaign is then described, presenting real time measurements in the 4–5 GHz band. 3.4.2.1. Static measurement campaign over the 3.1–10.6 GHz band The measurement system used for the static measurement campaign over the 3.1–10.6 GHz band is presented in Figure 3.10.

Propagation channel

Rotating arm

Webcam

Rotating arm driver

USB GPIB

RS 232

Port 1

Port 2

VNA HP8510C Driving and storage

Figure 3.10. Equipment setup for the static UWB sounding over the 3.1–10.6 GHz band

Measurements were taken using a VNA (see Figure 3.11(a)) in the frequency band 3.1–11.1 GHz with a frequency step Δf (meas) of 2 MHz. The full acquisition process consists of measuring 4005 frequency tones in a duration of about 15 seconds. Using a Hanning window, side lobes may be reduced to −32 dB. This compromise corresponds to an impulse response (meas) of 0.25 ns. resolution Rt

92

Ultra-Wideband Radio Propagation Channels

(a)

(b)

Figure 3.11. Measurement equipment: (a) HP8510C sounder and (b) rotating arm

In order to estimate the local PDP and assess the signal spatial fluctuations, a rotating arm with radius 20 cm was used to measure the radio channel at 90 different locations (see Figure 3.11(b)). This configuration corresponds to a circular path of 45λ and to a distance between two successive sensors below λ2 at the maximum frequency of 10.6 GHz. Measurements were performed using two CMA118/A antennas from the company Antenna Research Associates. These antennas are monoconical antennas with a metallic ground plane. Their radiation pattern is omnidirectional in the azimuth plane and a standing wave ratio (SWR) lower than 2 in the 1–18 GHz frequency band. It should be noted that the radiation pattern of these antennas strongly varies, especially in the elevation plane, as the frequency increases several octaves. Their complex gain has thus been characterized in 3D in the 1–10 GHz band with a 1 GHz step. Figure 3.12 illustrates the antenna characterization process.

UWB Propagation Channel Sounding

93

Figure 3.12. Measurement antennas. CMA 118/A antennas (from the ARA company) during their characterization

This sounding equipment was complemented with up to three wideband power amplifiers. The sounder calibration consists of a measurement sample taken while the receiver and the transmitter are directly cable connected. In order to achieve an accurate time reference, all cables involved in the measurement process need to be taken into account at the calibration stage. As active components, the amplifiers are not included in this measurement. Instead, they are characterized separately and their transfer function is subtracted from the measurements at the digital post-processing stage.

Measurements were taken in an indoor office environment. External walls are made of brick and concrete, and internal walls consist of thinner plaster and plastic boards. Two typical radio access configurations have been studied. In both cases, the transmitter was situated at a height of 1.40 m and was considered as the mobile terminal. The receiver was considered as the access point and was first placed in a meeting room at a height of 2.19 m, and then in a corridor at a height of 2.45 m. Figure 3.13 presents these two configurations. In both cases, LOS and NLOS configurations were assessed. The transmitter-receiver distance varied between 1 m and 20 m. Over the whole measurement campaign, the rotating arm was placed at more than 120 different locations, which corresponds to a set of over 10,000 UWB impulse responses available for statistical characterization. The analysis of these measurements is presented in Chapter 5.

Meeting room configuration

Figure 3.13. Measurement locations during the UWB sounding campaign over the 3.1–10.6 GHz band. Black squares represent fixed locations (receiver) and white circles correspond to the rotating arm locations (transmitter)

Corridor configuration

4m

94 Ultra-Wideband Radio Propagation Channels

UWB Propagation Channel Sounding

95

3.4.2.2. Static measurement campaign over the 2–6 GHz band The schematic description of the equipment used for the static measurement campaign over the 2–6 GHz band is presented in Figure 3.14. Measurements were performed using the VNA HP8753 D over the frequency band 2–6 GHz with a frequency step Δf mes of 2.5 MHz. The acquisition process for a full measurement consists of the measurement of 1601 frequency tones in a duration of 4 seconds. The CMA 118/A antennas have also been used for this measurement. The measurement did not require the use of power amplifiers at the transmitter or at the receiver. Indeed, the link budget without the amplifiers was high enough to support transmitter-receiver distances up to 12 m. CMA – 118/A MATLAB/SCILAB Post processing Analysis

Tx (Port 1)

Cable 20 m

Vector Network Analyzer

Tx Ant

Propagation channel

HP 8753 D PC Labview

GPIB

Cable 20 m

Rx Ant

Rx (Port 2)

CMA – 118/A

Figure 3.14. Equipment setup for the static UWB sounding over the 2–6 GHz band

The environments sounded during these measurements are residential houses: the first house is a modern building and the second one is an older building. The external walls of the first house consist of concrete blocks, bricks and insulation material made of glass wool. The external walls of the older house do not incorporate any insulating material. Internal walls of both houses are made of brick and plasterboards. Both dwellings are two-floor houses. However, measurements have been performed at the ground level only. The transmitter and the receiver are placed at the same height of 1.40 m. Figure 3.15(a) represents the first house with LOS measurement locations. Figures 3.15(b) and 3.15(c) represent the second house with both LOS and NLOS measurement locations. In these two environments, the number of measurements is respectively 89 and 230. 3.4.2.3. Dynamic measurement campaign over the 4–5 GHz band Finally, in order to study the effect that mobile people have on the UWB channel, we present a real time measurement campaign performed over a bandwidth of 1 GHz [PAG 06a].

96

Ultra-Wideband Radio Propagation Channels

(a)

(b)

(c)

Figure 3.15. Measurement locations during the UWB sounding campaign over the 2–6 GHz band. Squares represent fixed locations (Tx: transceiver) and circles represent mobile locations (receiver): (a) modern house; (b) old house in LOS; and (c) NLOS

UWB Propagation Channel Sounding

97

A few channel sounders only are currently capable of measuring the UWB channel in real time. This experimental study has been performed using the UWB sounder presented in section 3.3.3. The channel impulse response was measured every 10 ms, which enables the measurement of Doppler shifts up to 50 MHz. The analyzed band extends from 4 GHz to 5 GHz, with a resolution of 2 MHz, which corresponds to a maximum delay of 500 ns. At the transmitter and the receiver, CMA118/A antennas were used, as presented in section 3.4.2.1. Rx antenna Rx

B

Tx B

F People motion

F

Tx antenna

Figure 3.16. Environment of the real time experiment. F: forward movement, B: backward movement, Tx: transmitter, Rx: receiver

The experiment took place in a typical indoor office environment. All measurements were taken near a bend of the building’s main hallway, as depicted in Figure 3.16. The receiving antennas was fixed on a wall at a height of 2.10 m. The transmitting antenna was placed in the middle of the corridor at a distance of 11 m from the receiving antenna and at a height of 1.35 m. In order to assess the time variations of the UWB channel, measurements were taken over the fixed radio link as groups of people walked towards the end of the hallway and back. During this displacement, people occasionally obstructed the LOS path and other main paths of the channel impulse response. The number of people within each group varied from 1 to 12. This experiment corresponds to a practical situation where the user of a WLAN is standing in a crowd of people, in a subway corridor for instance. The measurement campaign consisted of a collection of 27 records of the time varying UWB radio channel, containing about 3,000 impulse responses each. Chapter 5 presents a statistical analysis of this experimental data.

98

Ultra-Wideband Radio Propagation Channels

3.5. Conclusion In this chapter, the different channel sounding techniques adapted to UWB measurements have been presented. Frequency domain methods use either a vector network analyzer or a chirp sounder. Time domain methods include pulsed techniques, correlation measurements and inversion techniques. Due to the wide analyzed bandwidth, the vector network analyzer method seems to be the most appropriate technique for static UWB channel sounding. However, its main limitation lies in its long measurement duration. Several seconds are indeed required to measure the 3.1–10.6 GHz band. For the acquisition of real time UWB channel measurements, an innovative sounding technique based on the extension of a wideband SIMO sounder has been presented. This adaptation corresponds to minor modifications of the original equipment and allows for real time measurements over a 1 GHz band. A literature survey made it possible to inventory about 20 UWB measurement campaigns since 1997. Most of these campaigns used a VNA-based frequency domain method. The reported campaigns cover the indoor residential and office environment, as well as some outdoor environments. Finally, the experimental setup of a typical sounding campaign has been illustrated through three examples: two measurement campaigns using a VNA over the 3–10.6 GHz and 2–6 GHz frequency bands respectively, and a series of real time measurements performed over the 4–5 GHz band using a multiple-band time domain sounder.

Chapter 4

Deterministic Modeling of the UWB Channel

4.1. Introduction Deterministic models are often used as site specific models allowing us to realistically predict signal propagation in a given environment using simulation software. Currently, little simulation software of this type is proposed for UWB in comparison to narrowband systems, where they are widely used to determine radio system deployment. The use of classical deterministic modeling software for UWB needs a particular adjustment in order to cover the entire frequency band of impulse signals. Concerning the total calculation field, it is mandatory to consider not only the power loss amplitude but also the phase information in order to easily reconstruct in the time domain the received signal corresponding to the modeled UWB link. This chapter describes the UWB deterministic modeling. After the presentation of classical techniques used for deterministic modeling, the specificities of UWB applications are described. Then, the different deterministic models proposed in the literature for UWB signal propagation are presented. Finally, theoretical formalisms are detailed and compared to measurement results in order to illustrate the deterministic modeling in the UWB context. 4.2. Overview of deterministic modeling Propagation models considered to be deterministic are obtained from simulations made in simplified propagation environments. They are based on

100

Ultra-Wideband Radio Propagation Channels

electromagnetic wave propagation theory. Their use requires a good knowledge on the propagation environment and allows us to obtain precise as well as accurate predictions of signal propagation in the channel corresponding to the considered environment. For a theoretical point of view, the wave propagation characteristics can be calculated by solving Maxwell equations. However, this requires us to make complex mathematical operations and to use powerful numerical calculations. The most frequently used approaches are based on frequency difference in time domain (FDTD) techniques, methods of moments (MoM) or ray techniques. 4.2.1. FDTD based approach The FDTD based approach allows us to obtain a complete cartography of the field on all points of a given map. It is typically used for electromagnetic field coverage in a given environment [LAU 95, SCH 97b, KON 99]. The FDTD used for modeling consists of solving Maxwell equations using regular spatial discretization in time. All derivations are simplified by algebraic systems of equation. The studied volume is discretized in various elementary cells, the size of which is related to wavelength of typically λ/10 or λ/15. The solving method fixes some restrictions in term of the considered cells sizes and time grid in order to ensure computation stability. The studied environment is limited by absorbing walls limiting the reflection phenomena on the boundaries [IBA 00]. These approaches demand huge memory spaces to obtain the solutions in all points of the considered environment and to update all iterative field calculations for the different instants. This approach is often used for small environments with respect to the wavelength or complementary to other approaches [YIN 00]. 4.2.2. MoM based approach Similarly to the FDTD approach, the MoM based approach is a numerical method which requires a large numerical memory for field calculation and radio coverage in a given environment [DEB 96, YAN 99]. The MoM is based on the use of an integral form of Maxwell equations. The integral system is transformed by an impedance matrix discretization which represents the interactions between elementary cells of the environment. The accuracy of the solutions obtained with this approach depends on the size of the considered cells.

Deterministic Modeling of the UWB Channel

101

This approach is used when the structure size is roughly a few wavelengths. It can also be considered complementary to other approaches like the ray based approaches in order to obtain hybrid models. Nevertheless, the MoM based approach is mainly used to validate results obtained with other approaches like the ray based approach [YAN 98]. 4.2.3. Ray based approach Based on geometric optic (GO) combined with uniform theory of diffraction (UTD) (see Appendix C), the ray based approach is well suited for the study of radio wave propagation. The GO considers that the energy is radiated along infinite tubes called rays. These rays define the propagation directions and can reflect or refract on all the surfaces they encounter. The use of UTD complements the GO as it introduces the diffracted rays and ensures the continuity of the field on regions where the GO predicts a non-existence of a field. Before the determination of the propagated field, we need to find the rays from which the GO and the UTD will be applied. This step of ray finding can use various techniques. There are two main techniques of ray determination: ray launching is considered to be a forward technique and ray tracing is considered to be a backward technique [SAR 03] (see Appendix D). When the rays are obtained, the propagated field can thus be calculated from the transmission to reception side. The ray based approach needs less numerical resources than the FDTD and MoM approaches for wave propagation prediction. Consequently, it is mostly used for deterministic propagation modeling [IKE 91, MCK 91, TAM 95, TAN 95, SAN 96, CHE 96, RIZ 97, VIL 99, ZHA 00]. Such approaches are not valid for low frequencies (typically lower than 100 MHz), when the size of objects interacting with rays become small or have the same order as the wavelength. An improvement of the propagation prediction with the ray based approach can be made by combining it with exact approaches such as those using FDTD or MoM. 4.3. Specificity of deterministic modeling in UWB When studying narrowband transmission techniques using deterministic software, much is made of the power loss of the transmitted signal. So, modeling allows the establishment of radio coverage maps on any considered environment at a given central frequency corresponding to the transmitted narrowband

102

Ultra-Wideband Radio Propagation Channels

signal. Indeed, we consider that the bandwidth is narrow enough to only focus the propagation study on the central frequency. In UWB, the frequency components of the transmitted signal cover a vast bandwidth which can reach 7.5 GHz. So, the performed simulation will necessarily address all the phenomena appearing on the entire bandwidth. Thus, we cannot simply focus on the propagation around the central frequency. This implies that we have to consider in the synthesized link both antennas and material properties of the considered environment on the whole covered frequency band. Another particularity of the UWB deterministic modeling is the need to consider the phase information related to the propagation as well as combining the effects of antennas and material properties. This phase information is important as it allows the identification of potential deformations (such as attenuation, dispersion, etc.) appearing on the received signal during the transmission. Deterministic modeling can thus be used in specific environmental configuration in order to better understand the effects of physical phenomena observed on results of channel propagation measurement campaigns. So, the use of site specific tool for deterministic modeling allows us on the one hand to study the waves propagation in various types of environments and in specific configurations, and on the other hand to physically understand the effects observed on measurements. 4.4. Overview of UWB deterministic modeling In this section, the four principal deterministic models which appear in the literature are described, with a main focus on their respective specificities. 4.4.1. Qiu model Some authors consider the study proposed by Qiu [QIU 02] on the diffraction undergone by an UWB signal as a UWB deterministic model. In the study made by Qiu, he mainly focuses on the distortions and dispersions introduced in a link and on system performances by single and multiple diffractions. 4.4.2. Yao model The particularity of the model proposed by Yao is that it takes into account the GO and UTD coefficients in the time domain in order to account

Deterministic Modeling of the UWB Channel

103

for the effects of the propagation channel interactions [YAO 03a, YAO 03b]. These time domain coefficients allow us to directly express the impulse response of each interaction [VER 90, BAR 91, ROU 95, YAO 97]. This approach can appear appropriate for the UWB channel propagation modeling as the reconstructed signal is a sum of each ray contribution. The contribution of each ray at the receiver side is a successive convolution of the impulse responses of each interaction of the considered ray with the transmitted signal. Nevertheless, a deterministic modeling tool using this approach will need significant numerical resources. In fact, a numerical operation consisting of a convolution needs great memory resources. So, although this model gives acceptable results, its use can become very restrictive in term of calculation time. 4.4.3. Attiya model The deterministic model proposed by Attiya [ATT 04] considers the GO and the UTD interactions coefficients expressed in the frequency domain (see Appendix C). The received signal is obtained in the time domain thanks to the use of an inverse Fourier transform. This allows us to directly use all the classical formulations corresponding to the frequency behavior of the propagation phenomena. Another difference between Yao and Attiya’s deterministic model lies in the consideration of antennas, something Yao neglected entirely. Attiya’s proposed model takes into account the antennas by inserting analytical formulations of antenna radiation in the expression of the reconstructed signal. In his model, he focuses on the case of horn antennas for which he proposes a time domain characterization technique [ATT 03]. The same impulse response obtained from measurement in an anechoic chamber between a transmitting antenna and a receiving antenna is directly applied in the time domain on each ray. For each ray, the relation corresponding to the effect of ray interactions is obtained after inverse Fourier transformation. So, the determination of the received signals after antennas are made by adding all the contributions of each ray. Each of these contributions is obtained by convolution of the impulse response between antennas with the relation corresponding to effect of a channel without antenna. So, it appears that this method shows two limits. The first limit is the consideration of the impulse response of antennas in order to insert their behavior in the model. The second limit is the application of the same impulse response for all rays, although they do not go and reach transmitting and receiving antennas respectively from the same direction.

104

Ultra-Wideband Radio Propagation Channels

4.4.4. Uguen and Tchoffo Talom model The other deterministic model proposed in the literature is that of Uguen and Tchoffo Talom [TCH 04, UGU 05]. The first contribution of this model mainly presents the synthesis of a received signal which adopts a formalism considering the channel ray by ray [UGU 02]. In this first contribution, some important elements of the transmission channel were not considered, such as the indoor multi-layered materials and antennas. Eventually, a more complete description was made [TCH 04, UGU 05]. In comparison to the first proposition, the introduced improvement concerns a better description of the consideration of each channel element in the model. This model is quite similar to the one proposed by Attiya [ATT 04]. However, unlike the Attiya model, the antennas are better taken into account in the model proposed by Uguen and Tchoffo Talom. Moreover, the construction of each ray contribution is made separately, which allows us to naturally access to the direction of departure (DoD) and direction of arrival (DoA) information. So, each ray is affected by the antenna functions corresponding to the actual DoD and DoA of the ray, defined in the frequency domain. 4.5. Illustration of a deterministic model formalism In this section, we illustrate the UWB deterministic modeling by presenting the theoretical formalism of the model proposed by Uguen and Tchoffo Talom [TCH 04, UGU 05]. This model allows us to synthesize a received signal for an indoor UWB link. We consider the application of an impulse signal p(τ ) on the transmitting antenna feeding port. As explained previously, it is not helpful to sum all the ray contributions before the transformation from the frequency domain to the time domain (see Appendix E). It is better to apply the transformation separately on each ray and then to sum each ray contribution directly in the time domain. This approach allows us to reduce the number of frequency points to consider and avoids unneeded frequency domain truncation of the complex exponential corresponding to the phase shift introduced by the propagation. The signal after the receiving antenna is obtained by summing all the vectorial and complex component of the field coming from the rays arriving on the receiving antenna. After the frequency sweep on the band of interest, the signal is expressed in the time domain using an inverse discrete Fourier transformation. So, this signal can be considered as the convolution of the signal p(τ ) with the SISO impulse response of the propagation channel.

Deterministic Modeling of the UWB Channel

105

The presentation of the theoretical formalism of the deterministic model is made by the detailed synthesis of the received signal. This detail mainly focuses on the ray by ray treatment of the propagation and antenna information as well as the proper consideration of antennas in the modeling.

4.5.1. Received signal synthesis The received signal r(τ ) is constructed as the sum of the appropriately shifted contribution rk (τ ) of the Nray rays obtained from the ray tracing step (see Figure 4.1) by: 

Nray

r(τ ) =

  rk τ − τk

[4.1]

k=1

The parameter τk is the delay corresponding to the free space propagation of the k th ray. The non-delayed signal rk (τ ) (see relation [4.2]) corresponds to the convolution of the transmitted signal p(τ ) applied at the transmitting antenna port with the non-delayed ray impulse response (RIR)  hk (τ ). rk (τ ) =  hk (τ ) ∗ p(τ )

[4.2]

In relation [4.1], Nray is one of the important parameters for the reconstruction of the received signal. It determines the realism of the obtained synthesized signal r(τ ). Deterministic models using rays are strongly dependent on the number of significant rays contributing to the total field. So, it is important to use rapid and appropriate techniques allowing us to obtain the main contributors in LOS or NLOS situations. Most of the time, this last situation requires us to consider a great number of rays in order to improve the realism of the synthesized signal.

4.5.2. Ray impulse response without delay The non-delayed ray impulse response (RIR) is noted  hk (τ ) and defined in the time domain by:      ck (τ )  f t τ, sˆtk [4.3] hk (τ ) = f r − τ, sˆrk  

r˜k (τ − τk )

r˜2 (τ − τ2 )

r˜1 (τ − τ1 )

=

r(τ)

τ2 τk

τ

τ

r˜k (τ)

r˜2 (τ)

r˜1 (τ)

Figure 4.1. Building of received signal r(τ ) by the sum of shifted rk (τ )

τ1

τ

τ

T FFT

106 Ultra-Wideband Radio Propagation Channels

Deterministic Modeling of the UWB Channel

107

f r (τ, sˆrk ) is a line vector corresponding to the impulse response of the received antenna in the arrival direction sˆrk of the k th ray. f t (τ, sˆtk ) is a column vector corresponding to the impulse response of the transmitted antenna in the departure direction sˆtk of the k th ray.  ck (τ ) is a 2×2 matrix corresponding to the consideration of attenuations and distortions introduced by the reflection, transmission or diffraction interactions appearing on the k th ray when propagating through the channel. This term does not consider the delay introduced by propagation τk . This delay is directly used when adding all the rk (τ ) at the appropriated time position (see Figure 4.1). sˆtk and sˆrk are the directions of departure (t) and arrival (r) of the k th ray. They are respectively the couples of polar coordinates (θkt , φtk ) and (θkr , φrk ) in the entire spherical base. Nevertheless, as reflection, transmission and diffraction phenomena have a simple analytical expression in the frequency domain, rk (τ ) is obtained from k (f ): an inverse Fourier transform applied on its frequency expression R      k (f ) Ft f, sˆt P (f ) k (f ) = Fr ∗ f, sˆrk C R k

[4.4]

P (f ) corresponds to the Fourier transform of the transmitted signal. Ft,r are the complex vectors corresponding respectively to the transmitting and receiving antenna frequency behavior. They allow us to consider the directivity Dt,r , the return loss Γt,r , the radiation efficiency η t,r and the antenna polarization state Ut,r [LO 88]:       Ft f, sˆtk = Gt1 f, sˆtk Ut f, sˆtk

[4.5]

      λ Fr f, sˆrk = −j Gr2 f, sˆrk Ur f, sˆrk 4π   2      Gt1 f, sˆtk = η t (f ) 1 − Γt (f ) Dt f, sˆtk

[4.7]

    Gr2 f, sˆrk = η r (f ) Dr f, sˆrk

[4.8]

  Ut,r f, sˆt,r = Uθt,r θˆt,r + Uφt,r φˆt,r k

[4.9]

[4.6]

108

Ultra-Wideband Radio Propagation Channels

The terms Ut,r are unitary vectors defined in the basis corresponding to the directions of departure sˆtk and arrival sˆrk for a given ray. These terms follow the relation: U∗ U = 1

[4.10]

λ The term −j 4π in the expression of Fr corresponds to the integration operation made at the receiver side.

 k is the 2×2 matrix corresponding to the frequency filter presented by the C propagation channel on the k th ray. This matrix is defined from the GO/UTD field and is expressed in a vectorial form: ⎤ ⎡ θ,θ θ,φ    C C  k (f ) = Ek = ⎣ ⎦ [4.11] C φ,θ Einc   φ,φ k C C  k the field at the receiving antenna and Einc the field coming from the with E k transmitting antenna in the direction sˆtk by:  t t Einc ˆk P (f ) [4.12] k = F f, s  k = Ek e+j2πf τk E

[4.13]

4.5.3. Ray channel matrix without delay The ray channel matrix without delay is expressed in a vectorial way by  k . It depends on the expression of the GO and the UTD field by the use C of the field Ek (see relation [4.14]). The superscript tilde corresponds to the extraction of the delay related to the propagation in Ek expression.  k Einc e−j2πf τk Ek = C k

[4.14]

Typically, there can appear on a k th ray approximately Nk interactions of reflection, transmission or diffraction nature. So, Ek is expressed by the relation: Ek =

1 s0k

1 Ak Gk e−j2πf τk Einc k s0k

[4.15]

corresponds to the spherical nature of the wave coming from the transmitting antenna.

Deterministic Modeling of the UWB Channel

109

τk is the delay related to the propagation of the k th ray. It is the sum of delays associated with the distances between the interactions appearing on the considered ray. τk =

Nk 

τki

[4.16]

i=0

Ak corresponds to the product of all the divergence factors of each interaction appearing on the ray. The expression of each divergence Aik is related to the considered interaction’s nature: Ak =

Nk 

Aik

[4.17]

i=1

Gk is the interaction matrix representing the consecutive reflections, transmissions or diffractions appearing on the k th ray. The term Gik of each interactions is related to the frequency, the polarization  or ⊥ and the reflection, transmission and diffraction incidence angles. These terms correspond to 2 × 2 matrices and are defined according to the incidence basis of reflection, transmission and diffraction interaction considered by: ⎤ ⎡  ,⊥  , G G ⎦ [4.18] Gik = ⎣ ⊥,   ⊥,⊥ G G

In other terms, the matrix Gik corresponds to the R, T or D matrix according to the interaction nature (see Appendix C). So, it is necessary to insert, in the global expression of Gk [4.19], the matrix used to change the basis related to the possible existence of an angle between the incidence plane of an interaction and the reflection, transmission or diffraction plane of the previous interaction. N  k  out,Nk out,i−1 in,1 t Bk →Brk i Bk →Bin,i k G1k MBk →Bk Gk M [4.19] Gk = M i=2

t

in,1

MBk →Bk is a matrix used to change the description of a field from a basis t Bk related to a given departure direction of a k th ray to the incoming basis of the first ray interaction. Bin,1 k

110

Ultra-Wideband Radio Propagation Channels out,Nk

MBk

→Brk

is a matrix used to change the field from the outgoing basis the last interaction to the incoming basis Brk of the arrival direction ray.

k of Bout,N k th

of the k

out,i−1

in,i

→Bk MBk is a matrix allowing for a k th ray to express the field, of the (i−1)th interaction in the incoming initially in an outgoing basis Bout,i−1 k in,i th basis Bk of the i interaction.

4.5.4. Described model results 4.5.4.1. Emitted waveform and considered scenario We consider the impulse waveform transmission p(τ ), which is obtained using the relation: p(τ ) =

Ep pˆ(τ )

[4.20]

with Ep the energy of the impulse signal p(τ ) and pˆ(τ ) a Gaussian impulse normalized in energy. pˆ(τ ) can be expressed using relation [4.21]: ! √   τ 2 2 2 √ sin 2πfc τ e−( β ) pˆ(τ ) = β π " √ 2 ln 10 α Bα,β = ≈ 0.216 α πβ 20 β

[4.21] [4.22]

where Bα,β is the band of pˆ(τ ) given at −α dB, β is a scaling factor allowing us to adjust the time domain support of pˆ(τ ) and fc is the central frequency of pˆ(τ ). In the frequency domain, the applied impulse signal is given by: P (f ) = Ep Pˆ (f ) ! √  2 β π  −[π β (f +fc )]2 √ e − e−[π β (f −fc )] Pˆ (f ) = 2

[4.23] [4.24]

So, |P (f )|2 is the energy spectral density (ESD) of the impulse signal. The impulse energy Ep is then obtained by integrating either the square of the

Deterministic Modeling of the UWB Channel

111

signal p(τ ) or |P (f )|2 , according to the following Parseval-Plancherel relation [PRO 83]:   P (f )2 df p2 (τ ) dτ = [4.25] Ep = R

R

To specify Ep , relation [4.26] proposed by [UGU 04] can be used: Ep =

1MHz Tr Pmax 2 1MHz σ γmax

[4.26]

So, the impulse energy can be determined with respect to the emission 1 MHz , the pulse repetition period Tr , limits specified by regulation using Pmax 1 MHz the capability of the the considered modulation given by σ, and γmax transmitting antenna to emit an amplified signal in the channel over a 1 MHz band. According to the FCC specifications concerning the transmitted UWB 1 MHz signal, the authorized maximum PSD is Pmax = −41.3 dBm/MHz. In this case, Ep is directly expressed by: Ep =

Tr 10−4.13 σ 2 γ 1 MHz

[4.27]

max

Figure 4.2 shows two impulses obtained for a central frequency fc = 4 GHz and an ideal1 transmitting antenna. We can note that the signal time spreading conversely increases with the band as well as the maximum level. The previously described model is applied for an indoor link of a LOS configuration in the environment represented in Figure 4.3. The rays reported in the figure are obtained using a 3D ray determination technique which combines ray launching and ray tracing [TCH 05a]. The material properties of the environment shown in Figure 4.3 are reported in Table 4.1. These properties are obtained from material characterizations [TCH 05a]. The frequency dependence of the materials is introduced by the permittivity expression in the interactions coefficients (see Appendix C). In this table, we can note that the floor and the ceiling are in reinforced concrete because the environment is the ground floor of a house with two levels.

1. An ideal antenna is an omnidirectional isotropic antenna with a unitary gain in all directions.

112

Ultra-Wideband Radio Propagation Channels

(a)

(b)

Figure 4.2. Impulses applied on an ideal transmitting antenna with fc = 4 GHz: B10 dB,β = 0.5 GHz (a) and B10 dB,β = 2 GHz (b)

Deterministic Modeling of the UWB Channel

113

Figure 4.3. 3D rays obtained for an indoor link in LOS configuration

Elements

Material properties

Materials r

r

μr

μr σ (S/m) Δδ (m) e (cm)

Wall

brick

3.8

0

1

0

0.05

0

10

Windows

glass

3.1

0

1

0

0

0

1.5

Doors

wood

2.84 −0.02

1

0

0

0

3

Ceiling

reinforced concrete 7.7

0

1

0

1

0

10

Floor

reinforced concrete 7.7

0

1

0

1

0

—

Table 4.1. Properties and structure of various elements of the considered environment

4.5.4.2. Channel matrix of each emitted waveform in the LOS case Considering the two waveforms (see Figure 4.2) for p(τ ) and the LOS configuration (see Figure 4.3), Figures 4.4 and 4.5 represent the four components of the channel matrix c(τ ):

cθ,θ (τ ) c(τ ) = φ,θ c (τ )



cθ,φ (τ ) cφ,φ (τ )

[4.28]

These illustrations are an artifice of representation which allows us to report on the same time axis all the contributions of the rays associated with each component of the matrix c. Each component of c(τ ) is obtained by adding the electric field contribution of each of the Nray for the considered component.

114

Ultra-Wideband Radio Propagation Channels

This representation allows us to underline the time domain behavior of the Nray ray fields arriving at the receiver without considering any transmitting or receiving antenna. We can note in these figures that the field level is weak on the cross components (cθ,φ and cφ,θ ). So, in order to obtain the received signal, the antennas considered at the transmitting and receiving sides will project these c(τ ) matrix components according to their characteristics [TCH 05b]. The shape of the final obtained signal will strongly depend on the components of c(τ ) modified by the chosen couple of antennas. Moreover, when the frequency band of the impulse p(τ ) decreases, each contribution of all rays can no longer be clearly isolated. For a band B10 dB,β = 500 MHz and for each component of c(τ ), the obtained signal corresponds to a compact grouping of the ray contributions arriving at a time lap with approximately the same width as the transmitted signal. This does not allow us to isolate the contribution of each ray but underlines the progressive rise of shadowing as the transmitted signal bandwidth decreases. 4.5.4.3. Received signal with ideal antennas In this part, from the components of channel matrix c (see Figure 4.5) and for the LOS case as well as the transmitted pulse p(τ ) of Figure 4.2(b), we focus on the reconstructed waveform obtained in the case where the antennas at transmission (Tx) and reception (Rx) sides are ideal omnidirectional, with unitary gain. Figures 4.6(a) and 4.6(b) show the reconstructed signal r(τ ) obtained respectively for a couple of antennas polarized along θ and φ. In the considered configurations, the transmitting and receiving antennas show a good accordance in term of polarization. So, the reconstructed signals (see Figures 4.6(a) and 4.6(b)) are respectively a projection of the channel matrix c(τ ) components cθ,θ (see Figure 4.5(a)) and cφ,φ (see Figure 4.5(d)). In the case of a real antenna, the received signal r(τ ) will probably be a less simple projection of different matrix c components. So, it will no longer be easily identified to one of the matrix c(τ ) components. One of the interests of the deterministic model detailed in section 4.5 is the ease of identifying DOA and DOD information. This is because the signal r(τ ) is reconstructed thanks to the rays obtained after ray tracing which directly gives the information corresponding to the direction of the rays. The other interest is that no sum is beforehand applied on the contributions of each ray. So, it is easy to extract the contribution associated with each ray.

(d)

(c)

Figure 4.4. Channel matrix component c(τ ) for the scenario of Figure 4.3 with the impulse p(τ ) of Figure 4.2(a): cθ,θ (τ ) (a), cθ,φ (τ ) (b), cφ,θ (τ ) (c) and cφ,φ (τ ) (d)

(b)

(a)

Deterministic Modeling of the UWB Channel 115

(d)

(c)

Figure 4.5. Channel matrix component c(τ ) for the scenario of Figure 4.3 with the impulse p(τ ) of Figure 4.2(b): cθ,θ (τ ) (a), cθ,φ (τ ) (b), cφ,θ (τ ) (c) and cφ,φ (τ ) (d)

(b)

(a)

116 Ultra-Wideband Radio Propagation Channels

Deterministic Modeling of the UWB Channel

117

(a)

(b)

Figure 4.6. Received signal r(τ ) for the LOS scenario of Figure 4.3, the pulse p(τ ) of Figure 4.2(b) and the ideal omnidirectional antennas at Tx and Rx sides: Tx-Rx antennas polarized along θ (a) and Tx-Rx polarized antennas along φ (b)

118

Ultra-Wideband Radio Propagation Channels

Figure 4.7 illustrates the extraction of DOA information corresponding to the signal reported in Figure 4.6(a). We can note that the obtained rays are well described in 3D. The direct path is clearly identified. It arrives at the receiving antenna side in the direction corresponding to the angles θ ≈ 95◦ and φ ≈ 245◦ . Here, the θ direction is not 90◦ because the transmitter and receiver antennas are not placed at the same height.

4.6. Consideration of real antenna characteristics in deterministic modeling Previously when ideal antennas were considered, we could easily identify the matrix c(τ ) component corresponding to the signal received after the Rx antenna. Here, real couple of antenna radiation characteristics are considered. In Figure 3.12, the used antennas which are called the CMA (Conical Monopole Antenna) are represented. The characteristic of these antennas are obtained from measurements performed on 4 π steradian in the Stargate 32 near-field antenna measurement engine of Satimo (see Figure 4.8) [TCH 05b]. The considered modeling configuration is the case illustrated in Figure 4.3. The received signal is illustrated in Figure 4.9(a). We can note that the omnidirectional characteristic of the CMA allows us to obtain a signal different from those obtained previously with ideal antennas. So, the obtained signal is no longer easily identified to one component of the channel matrix c(τ ) (see Figure 4.5). Figure 4.9(b) illustrates the amplitude and phase contribution applied by the antennas on each ray. The rays corresponding to the main contribution on the received signal are represented by a dark line. The contribution of a ray is thus proportional to the gray intensity used for its drawing. The darkest rays are those for which the combined directivity of transmitting and receiving antennas are important. If a rotation is applied along θ in order to fit both antenna directions of maximum radiation in elevation, the received signal will have a higher level than in the previous case (see Figure 4.10) and the other directions will contribute less to the obtained signal.2 We can note that the consideration of real antennas characteristics in the deterministic model is crucial and contributes to the validation and realism of the received signal synthesized with the modeling.

2. By comparing the two figures, it seems that the second RI is less dense. In fact, it is the first and main ray which has more energy in this case.

Figure 4.7. Illustration of r(τ ) DOA (see Figure 4.3) and the Tx-Rx ideal antennas polarized along θ

Deterministic Modeling of the UWB Channel 119

120

Ultra-Wideband Radio Propagation Channels

Figure 4.8. Satimo Stargate 32 near-field antenna measurement engine

4.7. Building material effects on channel properties The previously described studies were made for materials whose properties are reported in Table 4.1. So, the received signal reported in Figure 4.11(a) is obtained for a LOS link (see Figure 4.3), the waveform transmission in Figure 4.2(b) and the use of a couple of CMA antennas. This signal is the same as that reported in Figure 4.9(a). Considering the properties reported in Table 4.2, the effect of building material properties on the received signal synthesized by deterministic modeling is underlined. The new adopted properties correspond to a reduction of the previous wall thickness values (see Table 4.1), to a change of window structure and especially to an increase of floor and ceiling conductivity. In fact, the reinforced concrete used for constructing floors and ceilings at various stages of house building are made with metallic rods which can contribute to the increase in conductivity. The signal received with these new material properties shows important differences in comparison to the previous signals (see Figure 4.11). There are rays arriving after the direct path which show a higher level. These rays are those which connected the transmitter and receiver and reflected on the floor or the ceiling. So, the conductivity increase σ of the reinforced concrete introduces a high level contribution on the received signal for the rays which interact with the ceiling or the floor.

Deterministic Modeling of the UWB Channel

(a)

(b)

Figure 4.9. Received signal and ray contributions corresponding to the CMA antennas: received signal after the receiving antenna (a) and 3D rays with their corresponding contribution (b)

121

122

Ultra-Wideband Radio Propagation Channels

(a)

(b)

Figure 4.10. Received signal and ray contributions corresponding to the CMA antennas (rotation of 35◦ in θ for both Tx and Rx antennas): received signal after receiving antenna (a) and 3D rays with their corresponding contributions (b)

Deterministic Modeling of the UWB Channel

123

(a)

(b)

Figure 4.11. Received signal obtained with CMA antennas for two configurations of building material properties: case of materials in Table 4.1 and case of materials in Table 4.2

124

Ultra-Wideband Radio Propagation Channels

Elements

Material properties

Materials r

r

μr

μr σ (S/m) Δδ (m) e (cm)

Walls

brick

3.8

0

1

0

0.05

0

7

Windows

glass

3.1

0

1

0

0

0

0.5

air

1

0

1

0

0

0

0.5

glass

3.1

0

wood

2.84 −0.02

Doors

1

0

0

0

0.5

1

0

0

0

3

Ceiling

reinforced concrete 7.7

0

1

0

10

0

10

Floor

reinforced concrete 7.7

0

1

0

10

0

—

Table 4.2. Properties and structure of various building environment considered for the study of material influence

In addition to the antennas, the change of material properties strongly affects the received signal shape. In order to increase the realism of the waveforms obtained with a deterministic modeling tool, the characterization of building materials is needed to insert into the modeling the good material properties for the environment considered in link modeling [KRA 93, SAT 95, HUA 96, COU 98, MUQ 03a].

4.8. Simulation and measurement comparisons In this section, comparisons are made between the results of the realized measurements (see section 3.4.2.2) and the performed simulations using the deterministic model described in section 4.5. These comparisons allow us to evaluate the impact of the antenna characteristics in the described model and the received signal building for various LOS links. These comparisons consider a transmitted signal covering a band of 2–6 GHz. As the measurements were made in the frequency domain, no impulse signal is applied. Nevertheless, the transmitted signal corresponds to a sinc function in the time domain.

4.8.1. Evaluation of real antenna consideration To evaluate the consideration of antenna radiation characteristics in the deterministic model described in section 4.5, direct link measurements were made in an anechoic chamber. This configuration allows us to be free from multipath and to obtain a direct link with only one ray [TCH 06]. For

Deterministic Modeling of the UWB Channel

125

this evaluation, two antenna couples are used: directive horn antennas and omnidirectional CMA antennas. In the anechoic chamber, the antennas are placed at the same height and directed, in the case of horn antennas, so that both antenna directions of maximum gain face each other. This configuration is reproduced in simulation for the same departure and arrival directions as in the measurement. The simulation uses antenna characteristics data obtained from wideband measurement made in the Stargate 32 engine [TCH 05b]. Figure 4.12 illustrates the impulse response and transfers functions obtained with measurement and simulation in the case of the couple of horn antennas. We can observe a good matching between measurements and simulation results. Although there is only one ray, the obtained transfer functions are not constant. This can be explained by the frequency dependencies of antenna characteristics which affect the channel transfer function. Figure 4.13 illustrates the impulse responses and transfers functions obtained with measurement and simulation in the case of the couple of CMA antennas. We can also notice in this case a good matching between measurements and simulation results. The comparison of these two configurations testify to the relevance of antenna characteristics in deterministic link modeling. Indeed, according to their characteristics, antennas will affect the shape of the received impulse responses. Moreover, the comparison between measurement and simulation validates the adopted vectorial insertion of antenna characteristics in the described deterministic model. 4.8.2. Evaluation of impulse response reconstruction To evaluate the impulse response reconstruction, the focus here is on LOS links for which the measurement configurations are described in section 3.4.2.2. In each of the shown figures, the measured and simulated impulse responses as well as transfer functions are superimposed. The measurement and simulation results are respectively represented in gray and black. These illustrations concern four typical LOS situations extracted from 126 measurements points made in the environment described in section 3.4.2.2. Figures 4.14 and 4.15 represent the results obtained considering the four following positions corresponding to 1.14 m, 4.38 m, 6.78 m and 8.94 m distances.

126

Ultra-Wideband Radio Propagation Channels

The measured and simulated transfer functions show a great similarity in terms of level and fluctuations in form (see Figure 4.14). The same high frequency decrease is observed in measurement and simulation. Nevertheless, some differences are presented on the transfer function reported in Figure 4.14(a). These differences can be explained by the fact that for the presented results the transmitter was placed near a stone made fireplace. In simulation, a normal wall made with concrete was considered. Moreover, some differences can also be observed in phase information. This can be explained by the rays considered for the modeling, which are insufficient to provide access to the degree of measurement detail. Although the transfer functions seem different, we can note a great accordance between measured and simulated impulse responses (see Figure 4.15). Moreover, the simulated impulse responses are less consistent in term of rays compared to the measurement impulse responses. This can be explained by the simplified description of the environment used in the modeling. This simple description of the environment leads us to discard furniture and the inappropriate material properties for the considered environment walls. We may keep in mind that in such situations of very good concordance between simulation and measurement results, the simulation represents the benefit of giving additional information like departure and arrival angles. The channel is here known on various dimensions and with less cost than using a sounder with a single sensor.

4.9. Conclusion For a long time, the deployment of narrowband technologies has used the deterministic modeling of the radio propagation channel to establish coverage maps. With the use of UWB technology, some deterministic models have been proposed for signal prediction in new context. These models allow signal prediction and the rapid study of various environments with low costs in terms of channel transmission effects on the UWB link. From all the deterministic models presented, those which use frequency domain formalisms clearly seem better suited for the study of UWB wave propagation. More especially, the detailed Uguen and Tchoffo Talom model allows us to easily insert the antenna radiation information in the model. Moreover, this model naturally enables the access to DoD and DoA information as the electromagnetic calculations are performed ray by ray. The contributions of all the rays are then summed to obtain the overall received signal.

Deterministic Modeling of the UWB Channel

127

When deterministic modeling is used in UWB, it is important to take into account antenna characteristics and to use appropriate material properties for the considered environment. The reconstructed signal is strongly dependent on the number and relevance of the rays used in modeling. This firstly depends on the techniques used for ray determination and secondly on the details with which the environment is described.

(V)

Ultra-Wideband Radio Propagation Channels

delay (ns)

(a)

(level)

Magnitude

Freq (GHz) Phase

(radian)

128

Freq (GHz)

(b)

Figure 4.12. Measurement (gray) and simulation (black) received signals for the couple of horn antennas: (a) impulse response and (b) transfer function: magnitude and phase

(V)

Deterministic Modeling of the UWB Channel

delay (ns)

(a)

(level)

Magnitude

(radian)

Freq (GHz) Phase

Freq (GHz)

(b)

Figure 4.13. Measurement (gray) and simulation (black) received signals for the couple of CMA antennas: (a) impulse response and (b) transfer function: magnitude and phase

129

(leve l)

(radian)

(leve l)

(radian)

(d)

Freq (GHz)

Freq (GHz) Phase

Magnitude

(b)

Freq (GHz)

Freq (GHz) Phase

Magnitude

Figure 4.14. Measured (gray) and simulated (black) transfer functions for 4 distances between Tx and Rx: (a) d = 1.14 m, (b) d = 4.38 m, (c) d = 6.78 m and (d) d = 8.94 m

(c)

Freq (GHz)

Freq (GHz) Phase

Magnitude

(a)

Freq (GHz)

Freq (GHz) Phase

Magnitude

(leve l) (radian) (leve l) (radian)

130 Ultra-Wideband Radio Propagation Channels

delay (ns)

delay (ns)

(d)

delay (ns)

(b)

Figure 4.15. Measured (gray) and simulated (black) normalized impulse responses for 4 distances between Tx and Rx: (a) d = 1.14 m, (b) d = 4.38 m, (c) d = 6.78 m and (d) d = 8.94 m

(c)

(V) (V)

(V)

(V)

delay (ns)

(a)

Deterministic Modeling of the UWB Channel 131

This page intentionally left blank

Chapter 5

Statistical Modeling of the UWB Channel

Deterministic modeling makes a relatively accurate reproduction of the UWB channel properties possible for a given configuration in a known environment. Assuming that the elementary propagation phenomena are well modeled, the obtained impulse responses can be very realistic. The main constraints linked to this type of model lie in their long calculation time and the necessity of describing the considered environment in detail. Statistical models represent an interesting alternative for the simulation of UWB communication systems. They consist of reproducing a possible behavior of the propagation channel in a given type of environment. They are based on a large number of measurements, from which each parameter of the model is defined using a statistical law. These models enable the random generation of different impulse responses. This chapter presents the statistical modeling of the UWB channel through a practical approach. The principles of UWB propagation channel characterization is first illustrated from a series of measurements performed in an indoor office environment. For each step of the characterization process, experimental results are compared to the main anaylses published in the literature. Following a description of the different statistical models of the UWB channel, a full channel model is detailed. Its practical conception is based on a set of experimental characteristics. In particular, advanced techniques are presented for the modeling of spatial and temporal variations of the UWB channel.

134

Ultra-Wideband Radio Propagation Channels

5.1. Experimental characterization of channel parameters In this section, the characterization process of the UWB propagation channel is illustrated from a measurement campaign covering the whole FCC frequency band. The description of this measurement campaign is given in section 3.4.2.1. This study also compares the experimental results from different analyses of the UWB channel.

5.1.1. Propagation loss 5.1.1.1. Frequency propagation loss One of the channel properties characteristic to UWB signals is the power decay observed with increasing frequency. In an ideal free space configuration, the propagation loss is given by the Friis formula, as recalled in equation [2.34]. This formula implies that for a given distance d, the channel power transfer function (see equation [2.36]), expressed in dB, should follow a frequency variation in the form of −20 log(f ). It should be noted that this frequency dependence is linked to the effective area of an isotropic antenna and is not strictly speaking a characteristic of the propagation channel. In the literature, the attenuation of the received power as the frequency increases has been observed in different studies dedicated to antennas [KOV 03, HOF 03], or to the UWB channel [CHE 02, KUN 02a, ALV 03, BAL 04b, HAN 04, CHO 05, PAG 05]. As an example, Table 5.1 presents different estimates of the frequency dependent path loss exponent Nf . We may observe a relative diversity in the obtained values, as some of the authors even reported an increase in the received power with increasing frequency [KOV 03]. This may be explained by the high dependence between the parameter Nf and the measurement antenna. Measurement campaign

Nf

Whyless.com Aalborg University [KUN 02a] [KOV 03]

1.6 to 2.8

−0.3 to 5.5

Instit. for Infocomm Research [BAL 04b]

Samsung [CHO 05]

1.0 to 3.7

2.0 to 3.1

Table 5.1. Estimation of the frequency dependent path loss exponent for different analyses of the UWB channel. The published values have been adapted to the definition of the parameter Nf used in this book

In order to estimate the frequency dependent path loss, we studied the channel attenuation at different frequencies regularly spaced between 4 GHz and 10 GHz. For each measurement location, the path loss P L(f, d) was

Statistical Modeling of the UWB Channel

135

extracted from the power transfer function at the selected frequencies. In order to remove the distance dependency, each power transfer function was initially normalized by arbitrarily setting the attenuation of the total received power over the whole measurement bandwidth to 0 dB. The resulting normalized path loss P Lnorm (f ) can be compared to a model in the form:     f + S(f ) [5.1] P Lnorm (f ) = P Lnorm f0 + 10Nf log f0 where S(f ) represents a residual term with zero mean expressing the difference in dB between the measurement and the model. 10

PL

norm

(f) (dB)

8 6 4 2 0 -2 -4 3

4

5 6 7 Frequency (GHz)

8

9

10 11

Figure 5.1. Average normalized path loss vs. frequency

The normalized path loss averaged over all measurement locations is represented as a function of frequency in Figure 5.1. It should be noted that the antenna gains GT (f ) and GR (f ), measured in an anechoic chamber, were subtracted from each power transfer function at the selected frequencies, prior to path loss calculation. For each antenna, the antenna gain was selected by taking the direction of the direct transmitter-receiver path into account. This approach may seem simplistic a priori, as the total power is not only received via the direct path, but also via numerous multipaths arriving from other directions. However, with no further knowledge of the departure and arrival direction of these secondary paths, this method makes a sensible compensation of the antenna effect possible. We may observe that the dispersion of the measured plots around the linear approximation is reduced to a standard deviation of σS = 0.6 dB. The frequency dependent path loss exponent is Nf = 2.28. With respect to the error level inherent to the measurement

136

Ultra-Wideband Radio Propagation Channels

and calculation methods, this value may be considered close to the theory (Nf = 2). Hence, we recommend using the theoretical frequency loss of 20 log(f ) in the modeling of UWB propagation channels, as suggested in [BUE 03]. 5.1.1.2. Distance propagation loss In the previous section, we observed that the used antennas may have a non-negligible impact on the radio parameters. In the following analyses, in order to minimize this effect, the collected data were corrected by accounting for the gain of both antennas, measured in the direction of the transmitter-receiver path. The antenna radiation patterns, measured every GHz, were interpolated in frequency. According to the previous analysis on the frequency path loss, all measurements were fitted to a general formula as follows:       f d + 10Nd log + S(f, d) [5.2] P L(f, d) = P L f0 , d0 + 20 log f0 d0 where f0 represents the central frequency of 6.85 GHz and d0 is an arbitrary distance of 1 m. 40 LOS NLOS

Attenutation (dB)

50 60 70 80 90 100 110 0.6 0.8 1

2

3 4 5 6 8 10 Distance (m)

20

30 40

Figure 5.2. Path loss vs. distance. Each point represents the median attenuation in the FCC band

For each measurement location, the accounted path loss is the median attenuation in the FCC band, after shifting each measurement to the reference frequency f0 . Path loss exponents were obtained by linear fit in each LOS and NLOS situation. Figure 5.2 presents the obtained results. The measurement plots mainly follow a linear decay in log-scale, which corresponds to an

Statistical Modeling of the UWB Channel

137

exponential decay of the received power with respect to the distance. In the LOS situation, a path loss exponent Nd = 1.62 was recorded, with a standard deviation σS = 1.7 dB.1 In the NLOS case, the measurement plots are somewhat more dispersed, with a distance dependent path loss exponent Nd = 3.22, and a standard deviation σS = 5.7 dB.2 The values of the parameter P L(f0 , d0 ) were respectively evaluated at 53.7 dB and 59.4 dB. Table 5.2 shows that these values are in line with other analyses of the UWB channel published in the literature. For comparison purposes, the UWB path loss parameters proposed by the standardization organization ITU [ITU 04] are also reported. More details regarding the influence of frequency on the path loss coefficients are given in [PAJ 07]. In general, these parameters undergo a negligible variation when they are observed on partial frequency bands within the 3.1–10.6 GHz band. 5.1.2. Impulse response characterization Figure 5.3 presents typical PDP measured in LOS and NLOS configurations, as well as one of the 90 impulse responses. The delay on the x-axis has been converted in path length in meters, to ease the interpretation of the main paths. In both LOS and NLOS situations, we may observe one or several clusters, corresponding to a main echo followed by an exponential decay of diffuse power. In the LOS case, walls or pieces of furniture in the vicinity of the radio link generate significant reflected or diffracted echoes, which explains the presence of peaks in the PDP. An attenuation of 10 dB to 20 dB has thus been observed between the power of the main path of each cluster and the power of the secondary paths. The general shape of the PDP is globally smoother in the NLOS case. 5.1.2.1. Delay spread The RMS delay spread τRM S was calculated for each measured PDP, over the whole 3.1–10.6 GHz band. In order to minimize the effect of noise, a threshold placed 20 dB below the maximum value of the PDP was used.

1. In the LOS case, the value of Nd may be lower than in the theoretical case of free space (Nd = 2). This is due to the waveguide effect, frequently observed in indoor configurations (see section 2.2.2). 2. This significant value of the standard deviation in the NLOS case may be explained by the diversity of NLOS configurations, as the obstruction between the transmitter and the receiver may result from a single plasterboard or several concrete walls.

138

Ultra-Wideband Radio Propagation Channels

Measurement campaign

Nd LOS

UltRaLab [CAS 01] AT&T Labs - MIT [GHA 02a]

σS (dB) NLOS

LOS

2.4 1.7

Time Domain Corporation [YAN 02]

NLOS

3.5

1.6

2.1 1.72

4.09

Whyless.com [KUN 02a]

1.58

1.96

UCAN - CEA LETI [KEI 03]

1.6 to 1.7

3.7 to 7.2

Ultrawaves - Oulu University [HOV 03]

1.04 to 3.18 to 1.80 3.85

2.7

1.48

47

51

3.63

1.4

New Jersey Instit. of Tech. [DAB 03]

1.55 to 1.72

0.77 to 1.98

1.58 to 2.41 to 1.60 2.60

1.6 to 1.9

3.3 to 6.1

2.3 to 2.4

2.8 to 3.6

2.8 to 5.4

AT&T - WINLAB [GHA 03b] 2.01 to 2.95 to 2.07 3.12

2.3 to 3.2

3.8 to 4.1

1.3

NLOS

3.55

UCAN - Cantabria University [ALV 03]

NETEX - Virginia Tech [BUE 03]

LOS

5.9

Intel Labs [CHE 02]

NETEX - Virginia Tech [MUQ 03b]

P L(f0 , d0 ) (dB)

3.2 to 4.1

43.7 to 47.3 to 45.9 50.3

Hong Kong University [LI 03]

1.8

3.4

0.6

3.2

Ultrawaves - University of Rome “Tor Vergata” [CAS 04a]

1.92

3.66

1.42

2.18

48.68

47.24

Instit. for Infocomm Research [BAL 04b]

1.8

1.8 to 2.1

1.5

2.4 to 4.2

36.6

46.4 to 52

ETH Z¨ urich [SCH 04]

1.2 to 1.6

2.2

49 to 51

45

Samsung [CHO 05]

1.18 to 2.18 to 0.93 to 1.43 to 46.5 to 41.3 to 2.48 2.69 1.50 4.69 50.1 47.3

France Telecom - INSA [PAG 06b]

1.62

3.22

1.7

5.7

ITU Recommendation [ITU 04]

1.7

3.5 to 7

1.5

2.7 to 4

53.7

59.4

Table 5.2. Estimate of the distance dependent path loss for different analyses of the UWB channel

Statistical Modeling of the UWB Channel

139

(a)

Relative power (dB)

0

IR PDP

-10 -20 -30 -40 -50

0

20

40 60 Distance-delay (m)

80

(b)

Relative power (dB)

0

IR PDP

-10 -20 -30 -40 -50

0

20

40 60 Distance-delay (m)

80

Figure 5.3. Typical PDP and impulse response. (a) LOS and (b) NLOS configurations

Over the whole set of measurements performed in LOS configuration, the mean delay spread is τRMS = 4.1 ns, with a standard deviation στ = 2.7 ns. In the NLOS configuration, the mean delay spread is τRMS = 9.9 ns, with a standard deviation στ = 5.0 ns. Table 5.3 presents the results published in other analyses of the UWB radio channel. Values obtained for τRMS are in accordance with some of the previous experiments, although this parameter may vary from one experiment to the other. This is due to the high sensitivity of this parameter to the measurement environment and to the used experimental setup. The large scope of values in the published results may also be explained by the different thresholds used when calculating τRMS [CAS 04a].

7.71 to 17.34 0.53 to 4.55 3.38 to 5.49 19.9 28 to 31 15.6 21.08 to 53.62 12.48 to 14 4.1

New Jersey Instit. of Tech. [DAB 03]

NETEX - Virginia Tech [BUE 03]

AT&T - WINLAB [GHA 03a]

Hong Kong University [LI 03]

Lund University [KAR 04b]

Instit. of Infocomm Research [BAL 04b]

ETH Z¨ urich [SCH 04]

Samsung [CHO 05]

France Telecom - INSA [PAG 06b]

2.7

1.53 to 1.87

1.63 to 3.37

1.8

3.3

5.22

1.4 to 9.5

NLOS

5

5.22 to 8.03

1.87 to 7.04

2.8

2.45 to 3.47

στ (ns)

1.58 to 1.63

2.3

1.9 to 2.1

LOS

Table 5.3. Estimate of the delay spread for different analyses of the UWB channel

9.9

26.51 to 38.61

31.11 to 74.08

18.7 to 23.6

34 to 40

14.3

7.31 to 8.15

2.30 to 18.50

8.2

4.7

AT&T Labs - MIT [GHA 02a]

8.78 to 14.59 5.72

5.27

Time Domain Corporation (DSO) [PEN 02]

9.9 to 22.4

NLOS

Time Domain Corporation (correlator) [YAN 02]

10.9 to 12.2

UCAN - CEA LETI [KEI 03]

τRMS (ns) LOS

campaign

Measurement

140 Ultra-Wideband Radio Propagation Channels

Statistical Modeling of the UWB Channel

141

In order to observe the evolution of these parameters with frequency, the mean values of τRM S calculated for seven partial bands of 528 MHz each are represented in Figure 5.4 as a function of the central frequency of each band. For each band, the value of στ is represented by the length of the vertical line. The values of τRMS and στ obtained in each partial band are relatively close to the values calculated from the global UWB frequency band. As can be seen, the delay spread is not affected by the frequency. This was also observed by the University of Oulu from measurements performed in the 1–11 GHz band [JAM 04].

RMS delay spread (ns)

15

10

5 LOS 0

3

4

5

6 7 8 9 Central frequency (GHz)

NLOS 10

11

Figure 5.4. Mean delay spread for different partial bands. The length of the vertical line represents the corresponding standard deviation

5.1.2.2. Power delay profile decay Exponential decay constants The typical PDP presented in Figure 5.3 shows that the received power is grouped in different clusters, corresponding to the main propagation echoes. The decay of the received power with increasing delay is generally characterized with the inter- and intra-cluster exponential decay constants, respectively denoted Γ and γ (see section 2.4.1.4). To evaluate these parameters, the time intervals corresponding to the clusters of each measured PDP are identified by visual inspection. This technique was also used in [KAR 04a]. In each of the identified interval, a linear fit is performed at the delays included between the maximum and the minimum values of the PDP (expressed in dB). This enables the extraction of the intra-cluster exponential decay constant γ. The inter-cluster decay

142

Ultra-Wideband Radio Propagation Channels

constant Γ is obtained using a linear fit on the maximum of each cluster. In all cases, only the parts of the PDP presenting a power larger than 5 dB above the noise level were considered. Figure 5.5 illustrates this parameter extraction.

Relative power (dB)

0

Inter-cluster decay Intra-cluster decay

-10 -20 -30 -40 -50 -60

0

30

60 90 Delay (ns)

120

Figure 5.5. Extraction of the inter- and intra-cluster exponential decay constants

Among all PDP measured in a LOS situation, between 3 and 8 clusters (5.6 on average) were identified. The mean exponential decay constants have been evaluated as Γ = 15.7 ns and γ = 7.5 ns. In NLOS configuration, the PDP encompass between 1 and 4 clusters (2.4 on average). The mean exponential decay constants have been assessed as Γ = 16.5 ns and γ = 12.0 ns. Table 5.4 compares these experimental values with results published from similar experiments. In some analyses [CAS 02, ALV 03], the whole PDP was considered as a single cluster, which explains the lack of results regarding Γ. The value of the parameters Γ and γ is generally between 7 ns and 30 ns, even if some higher values have occasionally been reported [CRA 02, ALV 03, CHO 04a]. The inter-cluster decay is generally stronger than the intra-cluster decay. Results published in [KAR 04b] are a particular case where this tendency is inversed, and where the values of Γ and γ are quite low. This may arise from the measurement environment, as the experiment took place in a factory. For this experiment, a dependency of the parameter γ with the delay has been observed. In [CRA 02], the authors suggest that the constant Γ is linked to the building architecture, while γ is determined by the objects in the vicinity of the receiving antenna. The diversity of the sounded environments may thus explain the variety of the obtained results.

4.94

2.63 22.1 to 24.0 27.8 15.7

Lund University [KAR 04b]

Samsung [CHO 04a]

Instit. of Infocomm Research [BAL 04b]

France Telecom - INSA [PAG 06b]

7.5

14.1

14.3 to 30.8

4.58

10.83 to 13.97

Table 5.4. Estimate of the PDP exponential decay constants for different analyses of the UWB channel. The published values have been adapted to the definition of the parameters Γ and γ used in this book

16.5

24.6 to 30.4

36.9 to 51.5

13

Ultrawaves - University of Rome “Tor Vergata” [CAS 04b]

1.6

7.6

Intel Labs [FOE 03b]

16

2

21

7.1

6 to 8

NETEX - Virginia Tech [BUE 03, MCK 03]

9 to 20 100

14.5 to 21

UCAN - Cantabria University [ALV 03]

UCAN - CEA LETI [KEI 03]

84.1

UltRaLab [CRA 02]

27.9

16.1

LOS 13.6

NLOS

5.58

7 to 58

8.5

8

125 to 167

5 to 15

NLOS

12.0

25.3 to 33.8

27.4 to 38.6

γ (ns)

UltRaLab [CAS 02]

LOS

Γ (ns)

Whyless.com [KUN 02a]

campaign

Measurement

Statistical Modeling of the UWB Channel 143

144

Ultra-Wideband Radio Propagation Channels

Power decay constants The assumption of an exponential decay for the cluster and ray amplitudes was first introduced by Saleh and Valenzuela from their observation of the indoor wideband radio channel [SAL 87]. However, the analysis of the results from the measurement campaign shows that exponential decay is not completely satisfactory to model the slope of the PDP. Indeed, following this assumption, the PDP expressed in log-scale should present a linear decrease with increasing delay. The whole PDP as well as each constitutive cluster should hence fit into a triangular shape. This general shape is not representative of the experimental observations (see Figure 5.5). By considering successive echoes of the main path, we may identify two main sources of attenuation. On the one hand the propagation of the wavefront over a longer path induces a stronger power loss. On the other hand, delayed echoes undergo more propagation phenomena, which can be of a different nature, such as reflection or diffraction. This physical interpretation leads us to model the multipath attenuation following a similar approach to that used for distance path loss. We may recall that in this case, the observed attenuation at a transmitter-receiver distance d is proportional to d−Nd , where Nd represents the distance dependent path loss exponent. Regarding the different rays of the impulse response, the length of a propagation path is proportional to its delay. Hence, we suggest an adaptation of the Saleh and Valenzuela model, where the cluster and ray amplitudes decrease according to a power function. In the classical formalism presented in section 2.4.1.4, the amplitude βk,l of the k th ray in the lth cluster (see equation [2.33]) is replaced by the following formula:  2 βkl

=

2 β11

Tl T1

−Ω 

τk,l + Tl Tl

−ω [5.3]

where Tl represents the delay associated with the lth cluster and τk,l is the delay of the k th ray within the lth cluster. The parameters Ω and ω are respectively called inter-cluster and intra-cluster power decay constants. As for the case of exponential decay, the values of the parameters Ω and ω have been assessed by linear fit on the PDP clusters. In each case, the standard deviation σε of the error in dB between the model and the measurement has been calculated, in order to validate the proposed approach. Figure 5.6 illustrates the extraction of the parameters Ω and ω. It can be compared to the results reported in Figure 5.5. Regarding inter-cluster decay, using a power function instead of an exponential function leads to a decrease in the average standard deviation σε from 4.8 dB to 2.9 dB in the LOS case, and from 2.4 dB to 1.7 dB in the

Statistical Modeling of the UWB Channel

Relative power (dB)

0

145

Inter-cluster decay Intra-cluster decay

-10 -20 -30 -40 -50 -60

0

30

60 90 Delay (ns)

120

Figure 5.6. Extraction of the inter- and intra-cluster power decay constants

NLOS case. Regarding the intra-cluster decay, the average modeling error σε decreases from 1.9 dB to 1.8 dB in the LOS case, and from 1.7 dB to 1.6 dB in the NLOS case. This validates the proposed model, which is closer to our experimental measurements. Finally, in the LOS configuration, we observed a significant power attenuation G between the main path of each cluster and the following rays, as may be seen in the example of Figure 5.6. This phenomenon was already observed for UWB channels in [CAS 02] and [KUN 03]. Over the whole set of experimental measurements, we observed the average values Ω = 4.4 and ω = 11.1 in the LOS case, and Ω = 3.9 and ω = 10.2 in the NLOS case. In the LOS configuration, the average attenuation G was measured at 12 dB. 5.1.2.3. Ray and cluster arrival rate Study of the clusters In order to estimate the arrival time statistics for a new cluster, we consider the arrival time of the lth cluster, noted Tl , over the whole set of measured PDP presenting more than one cluster. This corresponds to the delay of the maximum value of the PDP in each time interval representing a cluster. The statistical distribution of the inter-cluster durations ΔT is then studied. ΔT is calculated as follows: ΔT = Tl+1 − Tl ,

l ∈ [1; L − 1]

[5.4]

where L represents the number of clusters in the PDP. Over the whole set of PDP presenting more than one cluster, the average inter-cluster duration was ΔT = 27.4 ns in the LOS case and ΔT = 40.1 ns in

146

Ultra-Wideband Radio Propagation Channels

the NLOS case. The graphs in Figure 5.7 are percentile-percentile diagrams, representing the experimental distribution percentiles of ΔT on the x-axis, and the theoretical percentiles of an exponential distribution with parameter Λ on the y-axis. The best fit leads to a value Λ = 27.41 ns = 36.5MHz in the LOS case, and Λ = 40.11 ns = 24.9 MHz in the NLOS case. In both cases, the alignment of the plots on the diagram diagonal shows that the exponential distribution is a reasonable approximation to modeling inter-cluster duration. (a) LOS

100

Theoretical ΔT (ns)

Theoretical ΔT (ns)

120

80 60 40

NLOS

150 120 90 60 30

20 0

(b) 180

0

20

40 60 80 100 120 Experimental ΔT (ns)

0

0

30

60 90 120 150 Experimental ΔT (ns)

180

Figure 5.7. Percentile-percentile diagrams for the inter-cluster duration. Experimental percentiles vs. theoretical percentiles corresponding to an exponential distribution with parameter Λ = 36.5 MHz in the LOS case (a) and Λ = 24.9 MHz in the NLOS case (b)

Study of the rays Individual echoes due to the different multiple paths are not directly observable on the measured PDP. Because of the limited frequency band of the measurement, each echo is received in the form of an impulse with non-zero duration. The impulse response is a continuous waveform composed of the sum of all individual contributions, each one presenting a different attenuation and a different phase rotation. Different methods are available to extract the delay and amplitude information of the main paths constituting an impulse response. The ¨ 74], was adopted CLEAN method, initially used in radio astronomy [HOG by different researchers for the characterization of the UWB radio channel [YAN 02, PEN 02]. This method was modified by the University of South California for the study of the arrival direction [CRA 02]. The Tokyo Institute of Technology used an algorithm based on the high-resolution method called space alternating generalized expectation (SAGE), also allowing the analysis

Statistical Modeling of the UWB Channel

147

of the arrival direction [HAN 03]. It should be noted that these two studies were based on measurements performed with a large number of co-located sensors. In order to illustrate the process of ray identification we present here the frequency domain maximum likelihood (FDML) algorithm [DEN 03a, LEE 02]. The search of ray locations is performed in an iterative way, from the representation of the impulse response in its real form h (τ ). As an assumption, the channel is thus described in the form: h (τ ) =

K 

  βk δ τ − τk

[5.5]

k=1

where K represents the number of rays, and βk and τk are the real amplitude and delay linked to the k th ray. The parameter βk may take negative values, in order to account for the phase inversion linked to some interactions, such as the reflections. At each iteration of the process, a new ray is detected by finding the correlation peak between the measured impulse response and a template signal, corresponding to the sounding waveform. Contrarily to the CLEAN algorithm, the FDML method proposes to optimize the whole set of detected rays. This requires a minimization of the squared error between the measured frequency spectrum and the synthetic spectrum, built from the identified rays. This optimization presents two main advantages. First, it enables the detection of superimposed rays, which does not always lead to a correlation peak. Second, the processing is performed in the frequency domain, which avoids the resolution limitations linked to the sampling rate in the time domain. More details on adapting the FDML algorithm to accelerate the calculation time are available in [PAG 05]. The results of the FDML algorithm allow us to study the arrival time of the k th ray, over the whole set of selected impulse responses. As with the clusters case, we study the distribution of the inter-ray durations, defined as follows: Δτ = τk+1 − τk ,

k ∈ [1; K − 1]

[5.6]

where K represents the number of rays in the impulse response. Over the whole set of measurements performed in both LOS and NLOS configurations, the average inter-ray duration was respectively evaluated at Δτ = 0.168 ns and Δτ = 0.161 ns. Figure 5.8 presents a percentile-percentile diagram used to compare the experimental distribution of Δτ to an exponential 1 distribution with parameter λ = 0.168 ns = 5.95 GHz in the LOS case and 1 λ = 0.161 ns = 6.19 GHz in the NLOS case. In this case, some differences may

148

Ultra-Wideband Radio Propagation Channels

be noted between the theoretical and experimental data, but the exponential approximation still provides an acceptable fit to the measurements. (a)

(b)

0.8

0.8 NLOS Theoretical ΔT (ns)

Theoretical ΔT (ns)

LOS 0.6

0.4

0.2

0

0

0.2 0.4 0.6 Experimental ΔT (ns)

0.8

0.6

0.4

0.2

0

0

0.2 0.4 0.6 Experimental ΔT (ns)

0.8

Figure 5.8. Percentile-percentile diagrams for the inter-ray duration. Experimental percentiles vs. theoretical percentiles corresponding to an exponential distribution with (a) parameter λ = 5.95 GHz in the LOS case and (b) λ = 6.19 GHz in the NLOS case

The experimental values obtained for the cluster arrival rate Λ and the ray arrival rate λ are compared with the results available in the literature, shown in Table 5.5. Regarding the cluster arrival rate, the observed values are generally in the order of 10 to several hundreds of MHz. The average duration between two clusters is thus in the order of 10 ns to 100 ns. It should be recalled that a cluster within the PDP corresponds to a main path, arising from transmissions or reflections on walls, on the ceiling or on the building ground. The parameter Λ is thus dependent on the structure of the building where the measurement took place. The ray arrival rate λ presents variable values depending on the experiment. Indeed, values obtained depend highly on the ray identification technique that was used in the analysis. For this reason, researchers from the German institute IMST advise to arbitrarily setting the inter-ray duration at the temporal resolution value obtained [KUN 02a]. In this case, the ray arrival rate would be equal to the width Bw of the analyzed band. 5.1.3. Study of small-scale channel variations The last characteristic of the UWB radio channel studied from the experimental campaign (see section 5.1) is related to the fast fading of the impulse response. During the campaign, a rotating arm was used, which enabled the measurement of the channel impulse response at 90 locations

200 16.7 26 70.9 85 to 115 18.6 36.5

NETEX - Virginia Tech [BUE 03, MCK 03]

Intel Labs [FOE 03b]

Ultrawaves - University of Rome “Tor Vergata” [CAS 04b]

Lund University [KAR 04b]

Samsung [CHO 04a]

Instit. of Infocomm Research [BAL 04b]

France Telecom - INSA [PAG 06b]

24.9

2.4 to 13.4

47 to 64

89.1

59

90.9

100

10 to 800

5946

280

Bw

NLOS

6194

270 to 360

1390 to 1790

2857

714

1500 to 5500

434.78

1160 to 1960

2000

1429

45 to 180

LOS

λ (MHz)

Table 5.5. Estimate of the average cluster and ray arrival rates for different analyses of the UWB channel. The published values have been adapted to the definition of the parameters Λ and λ used in this book

10 to 25

UCAN-CEA LETI [KEI 03]

21.98

UltRaLab [CRA 02]

NLOS 100 to 1000

LOS

Λ (MHz)

Whyless.com [KUN 02a]

campaign

Measurement

Statistical Modeling of the UWB Channel 149

150

Ultra-Wideband Radio Propagation Channels

situated around a circle of 20 cm in radius. For each measurement, the space fluctuation statistics were studied by comparing the 90 impulse responses collected locally. The study consisted of analyzing the statistical distribution of the amplitude of the received signal at each delay. In the literature, previous studies showed that this distribution was well represented using a Nakagami function [CAS 02]. The Nakagami m parameter was thus estimated for each measured PDP, at delays separated by 0.5 ns on the time scale (see Appendix B.1.3). An example of values for the parameter m is given for a specific measurement in Figure 5.9. As can be noted, the best fitted Nakagami distribution presents a parameter m close to 1 for the vast majority of the delays within the PDP. Thus, the amplitude distribution of the impulse response for a given delay may be correctly described using a Rayleigh distribution. This was observed for most of the measured PDP. In addition, we may observe that the cases where the parameter m takes higher values correspond to the main paths of the PDP. In this case, the value of the parameter m may increase to m = 4 or m = 5, and up to m = 8 in the extreme cases. The characterization of amplitude distribution in the UWB impulse response is a controversial issue in the literature. The Rayleigh distribution has frequently been observed in the study of UWB radio channel fast fading statistics [CRA 02, KUN 02a, SCH 04, KAR 04b]. Researchers from ETH Z¨ urich [SCH 04] and from the Lund University [KAR 04b] also noted a modification of this distribution for the main path. Other studies show that the fast fading is well represented by a Nakagami distribution [CAS 02, CAS 04b, BAL 04b]. In this case, the parameter m may vary with the delay. However, it has been demonstrated that a theoretical impulse response presenting a Rayleigh fast fading may be observed as following a Nakagami distribution, depending on the duration over which the received power is integrated in the time domain [KUN 03]. Finally, it should be noted that some analyses recommend that we use a log-normal distribution [KEI 03, FOE 03b, LI 03, BUE 03, MCK 03] or a Rice distribution [HOV 02]. In practice, we may distinguish between two sources of channel fluctuations [HAS 94a]. Spatial variations arise when at least one of the antennas is moved in an otherwise static environment. Temporal variations are due to environmental modifications and may be observed in fixed radio links. A study of the channel variations when the transmitting antenna is moved on a 1 m2 grid was presented in [PAG 04]. Results show that in the case of the UWB channel, the delay linked to the main paths of the impulse response significantly varies while the antenna is moved. This shift of the main paths in the time domain is due to the high resolution of UWB signals and needs to be taken into account when modeling the channel spatial variations. More details on these observations are

Relative power (dB)

Statistical Modeling of the UWB Channel

0

151

PDP

-10 -20 -30 -40 -50

0

20

40

60 80 100 Delay (ns)

120

140

0

20

40

60 80 100 Delay (ns)

120

140

Nakagami m

4 3 2 1 0

Figure 5.9. Nakagami m parameter analysis. PDP measured in an NLOS situation and parameter value m for each delay

available in [PAG 05]. In indoor environments, the temporal variations of the propagation channel are mainly due to moving people. This phenomenon is studied more particularly in the following section.

5.1.4. Effect of moving people The study of the effect of moving people on the UWB channel is based on the analysis of a measurement campaign performed in an indoor office environment. For this campaign, a UWB sounder enabling real time measurements over the 4–5 GHz frequency band was used. During the measurement process, a group of 1 to 12 people was walking in a corridor in the vicinity of a fixed radio link. A complete description of this campaign is given in section 3.4.2.3. 5.1.4.1. Observation of temporal variations A typical impulse response collected during the experiment is given in Figure 5.10. In this graph, the delay has been converted to path length in meters to ease the interpretation of multipaths. After the direct path (a), whose length corresponds to the transmitter-receiver distance (11 m), we may distinguish two echoes (b) and (c) corresponding to reflections on the corridor walls.

152

Ultra-Wideband Radio Propagation Channels

(a)

Power attenuation (dB)

70

(b) 80

(c)

90 100 110 0

10

20 30 40 Distance-delay (m)

50

60

Figure 5.10. Typical impulse response

A first observation of the effect that moving people have on the UWB channel is given in Figure 5.11. The time varying impulse response is represented in the case of 12 people walking back and forth through the radio link. Successive measurements are represented from left to right, while the vertical axis represents the excess delay converted in path length (m). The influence that moving people have on the CIR appears clearly on this graph. The main paths (a) and (b) are regularly obstructed by moving people, during both forward (t = 15 s to t = 27 s) and backward (t = 63 s to t = 74 s) displacements along the corridor. At other values of the excess path, we can observe strong signal fluctuations, with respect to the stationary part of the diagram. 5.1.4.2. Slow fading As a first step in the analysis, we observed the slow fading generated by human beings in the vicinity of the radio link. For this purpose, we studied the slow temporal evolution of the mean power received in the LOS path in the presence of people. Fast fading fluctuations were eliminated by averaging the received power using a sliding window. Figure 5.12 presents the aggregate effect of several people passing through the main signal path. In general, the progression of one person through the LOS path yields a maximum attenuation of about 8 dB, the shadowing effect lasting for about 4 s. The obstruction duration increases with the number of people, up to about 15 s for a group of 12 people. In this case, the maximum attenuation of the mean power is about 15 dB. We clearly see that the shadowing pattern obtained for groups of people is composed of superimposed

Statistical Modeling of the UWB Channel

0

0 ← Forward mov. →

5

← Backward mov. →

5 10

15 15 20

(b) 20

25 30

25

35

30

40

(c)

35

45 0

Relative attenuation (dB)

(a)

10 Distance-delay (m)

153

20

40 Time (s)

60

80

40

Figure 5.11. Time varying impulse response in the case of 12 moving people

individual contributions. However, the particular effect that each person has on the received signal is not always observable, as, for example, in the case involving 4 people. 5.1.4.3. Fast fading In addition to the large-scale fading generated by moving people, small-scale fading is observed while people are walking in the vicinity of the radio link. The signal received at a delay corresponding to the main paths of the impulse response may be thought of as a vector summation of several multipath components, as would be the case in a typical situation exhibiting Rician fading. As depicted in Figure 5.13, we may distinguish between two components of the received signal. The dominant component accounts for the signal normally received in a static environment. The random component represents the summation of all waves scattered by moving people. In order to accurately analyze the fast fading observed during experimentation, the random component was isolated by filtering. Figure 5.14 represents both magnitude and phase fluctuations of the random component extracted from the signal received via the main path, when obstructed by

Relative power (dB)

-15

-20

-25

-30

-15

-20

-25

-30

0

4

8

12

16 20 24 Time (s)

Received power Slow fading

4 people

28

32

36

-30

-25

-20

-15

-10

-5

0

5

0

4

8

12

16 20 24 Time (s)

12 people

Figure 5.12. Typical large-scale fading patterns for the LOS component. Effect of 1, 4 and 12 people

-10

-10

8 12 16 Time (s)

-5

-5

4

0

0

0

5

1 people

5

28

32

36

154 Ultra-Wideband Radio Propagation Channels

Statistical Modeling of the UWB Channel

155

Q Random component I

Dominant component

time

Figure 5.13. Vector decomposition of the received signal

12 moving people. This situation corresponds to the measurement depicted in Figure 5.12 (graph on the right). We may notice that the magnitude of the small-scale fading presents a high degree of regularity, compared to the non-stationary large-scale fading pattern. Using a Kolmogorov-Smirnov testing procedure (see Appendix B.2), the amplitude distribution of the random component is well suited to a Rayleigh distribution. This observation could be made for most of the available measurements, independently of the number of moving people. The signal received via the main paths of the impulse response, composed of a Rayleigh random component and a dominant component of greater amplitude, the resulting signal hence follows a Rician distribution (see Appendix B.1.2). The Rician K parameter is defined as the power ratio between the dominant component and the random fluctuations. As the dominant component presents a slowly time-variant amplitude, the parameter K varies over time accordingly, depending on the obstruction of the main path. We may notice in this example that the mean signal power of the random component is about 12 dB below the unobstructed signal level. Depending on the attenuation level of the dominant signal, the parameter K varies from about 12 dB down to less than −20 dB. In this case, the total received signal follows a Rayleigh distribution. These results were observed on other measurement records, with maximum values of the parameter K varying between 8 dB and 13 dB. In addition, the phase of the random component depicted in Figure 5.14 presents a rather unstable behavior while people are interfering with the main path of the impulse response, with distinct periods of linear progress. However,

156

Ultra-Wideband Radio Propagation Channels

Relative power (dB)

0 -10 -20 -30 -40 -50

↑ 14

16

18

20 Time (s)

Phase (rad)

↓

↑

22

24

22

24

↓

2 0 -2 14

16

18

20 Time (s)

Figure 5.14. Fast fading of the random component. LOS path, 12 people

we may note rapid and significant phase shifts at instants corresponding to fading nulls (indicated by arrows on the figure), due to the rapidly decreasing power. 5.1.4.4. Spectral analysis This section presents a spectral analysis the analysis of the temporal signal variations received via the main paths of the impulse response. Figure 5.15 represents the average scattering function PS (τ, ν) of the random component, for the delay τ corresponding to the LOS path. Measurements involving 1 to 12 moving people are taken into account, and the collected records were distinguished according to the direction of the movement. The general shape of the scattering function is triangular, with an average Doppler shift centered around 0 Hz. The spectrum width was calculated in terms of Doppler spread νRM S , defined in equation [2.38]. The calculated Doppler spread varied between 0.6 and 3.3 Hz, with no marked influence from the number of moving people. Similar 0 Hz-centered, triangular shapes of the Doppler spectrum are reported from continuous wave measurements of the channel temporal variations performed at frequencies around 1 GHz [HAS 94b, BUL 87].

Statistical Modeling of the UWB Channel

157

Relative power (dB)

0 Forward Backward

-5 -10 -15 -20 -25 -15

-10

-5 0 5 Doppler shift (Hz)

10

15

Figure 5.15. Average scattering function of the random component. LOS path, forward and backward motions

Some asymmetry can be observed in Figure 5.15 between measurements performed during forward and backward movements. This can be explained by the location of the antennas, which emphasize either the lengthening or the shortening of propagation paths, depending on the direction of the human motion. More details on the interpretation of these results can be found in [PAG 06a].

5.2. Statistical channel modeling In section 5.1, the characterization of the radio channel parameters was presented from a series of experimental measurements. The frequency dependent and distance dependent attenuation linked to the radio signal propagation was evaluated, as well as a number of parameters regarding the impulse response. The RMS delay spread, the PDP magnitude decay and the rays arrival rate are a few examples. Statistical models use these experimental parameters to realistically reproduce the channel effects. This section presents a few statistical models for the UWB propagation channel available in the literature. The analyses presented in section 5.1 are then exploited to illustrate in more detail the design of a statistical model based on experimental data.

158

Ultra-Wideband Radio Propagation Channels

5.2.1. Examples of statistical models In order to provide a unique channel model for the evaluation of different UWB systems proposals during standardization meetings, the IEEE 802.15 work group made several calls for contributions. Two statistical models were defined, the first one for short range, high rate, indoor applications (IEEE 802.15.3a model), and the second one for applications with longer range in both indoor and outdoor environments (IEEE 802.15.4a model). These models are briefly presented in the following sections. 5.2.1.1. IEEE 802.15.3a model The IEEE 802.15.3a model [FOE 03a, MOL 03] was developed from around 10 contributions, all referring to distinct experimental measurements, performed in indoor residential or office environments [GHA 02a, PEN 02, FOE 03b, HOV 03, KUN 02b, GHA 02b, CAS 02, CRA 02, SIW 02]. In order to reflect the phenomenon of ray clustering that was observed in several measurement campaigns, the model is based on the Saleh and Valenzuela formalism (see equation [2.31]). Parameters are provided to characterize the clusters and ray arrival rates (Λ and λ), as well as the inter- and intra-cluster exponential decay constants (Γ and γ). Four sets of parameters are provided to model the four following channel types: • the channel model CM 1 corresponds to a distance of 0–4 m in a LOS situation; • the channel model CM 2 corresponds to a distance of 0–4 m in an NLOS situation; • the channel model CM 3 corresponds to a distance of 4–10 m in an NLOS situation; • the channel model CM 4 corresponds to an NLOS situation with a large delay spread τRMS = 25 ns. Regarding channel attenuation, the IEEE 802.15.3a model proposes a theoretical approach using a path loss exponent Nd = 2 for the LOS situation, which is equivalent to a free space propagation. The NLOS case was not addressed. Finally, the fluctuations of ray amplitude modeled using a log-normal law (see Appendix B.1.6), and a random inversion coefficient is introduced to simulate the phase inversion observed in the impulse response due to reflections. This comprehensive model is a reference for the study of UWB systems. It can be applied in indoor environments and short range conditions. However,

Statistical Modeling of the UWB Channel

159

modeling of the path loss is not practically addressed. It can also be noted that the measurements used for the model calibration [PEN 02, CHE 02] are limited to at most 6 GHz bandwidth (2 GHz for the models CM 1 and CM 2). 5.2.1.2. IEEE 802.15.4a model In order to be representative of a larger number of potential applications, the IEEE 802.15.4a working group proposed a model with a wider scope in terms of both frequency and environments [MOL 04]. The targeted applications are low rate communications (from 1 kbps to a few Mbps), in the following environments: indoor (residential and office), outdoor, industrial (factory, etc.) and on-body (for WBAN applications). Two UWB frequency bands are considered: 2–10 GHz and 0.1–1 GHz. We present here the model corresponding to the first frequency band. The general structure of this statistical model is similar to the IEEE 802.15.3a model (see equation [2.31]). Some differences are however noteworthy regarding the shape of the impulse response: • The phase θk,l of each ray is no longer limited to the values 0 or π, but is uniformly distributed between 0 and 2π. Thus, this model reproduces the complex envelope of the baseband impulse response. • Ray arrival follows a dual law composed of two Poisson processes. Accordingly, the model proposes two ray arrival rates λ1 and λ2 , as well as a mixing parameter. • The exponential decay of each cluster increases with the delay. The intra-cluster exponential decay constant is thus of the following form: γl = kγ Tl + γ0

[5.7]

where Tl represents the time of arrival of the lth cluster and kγ accounts for the increase of the coefficient γl with increasing delay. The main difference between the IEEE 802.15.4a model and the IEEE 802.15.3a model is that the former accounts for a realistic path loss, in both the distance and frequency domains. The proposed model is independent of the transmitter and receiver antennas. After some changes in the proposed variables, this path loss model can be expressed in the form given in equation [2.35], and the model provides the parameter values equivalent to Nf , Nd , P L(f0 , d0 ) and σS . In addition, the small scale variations of the ray amplitude are modeled using a Nakagami distribution (see Appendix B.1.3). As for the Cassioli-Win-Molisch model, the parameter value m is a delay function.

160

Ultra-Wideband Radio Propagation Channels

Nine channel types were identified within the IEEE 802.15.4a work group. Each channel type is defined by a given set of parameters as follows: • the CM 1 and CM 2 models correspond to the indoor residential environment (respectively in LOS and NLOS configurations); • the CM 3 and CM 4 models correspond to the indoor office environment (respectively in LOS and NLOS configurations); • the CM 5 and CM 6 models correspond to the outdoor environment (respectively in LOS and NLOS configurations); • the CM 7 and CM 8 models correspond to the indoor industrial environment (respectively in LOS and NLOS configurations); • the CM 9 model corresponds to the outdoor environment in an NLOS configuration, in the specific case of a farm area or an area covered with snow. This model is more detailed than the IEEE 802.15.3a model, but is also somewhat more complex. The provided parameter sets are based on experimental measurements for each environment: residential [CHO 04b], office [BAL 04a, SCH 04], industrial [KAR 04b] and outdoor [BAL 04a, KEI 04]. A survey of the results from the literature complements these measurement campaigns. It should be noted, though, that the measurements performed in the office and outdoor environments covered frequency bands limited to 3 or 6 GHz. 5.2.1.3. Other models The Cassioli-Win-Molisch model The Cassioli-Win-Molisch model [CAS 02] is the result of a joint research work performed by the University of Rome “Tor Vergata” (Italy), Vienna University (Austria) and the UltRaLab laboratory from the University of South California (USA). This model is one of the first statistical models describing the UWB propagation channel. Despite some limitations, it is thus frequently cited in the studies on UWB. This model is based on a series of measurements performed by the UltRaLab laboratory in an indoor office environment, over a frequency band of about 1 GHz [WIN 97b]. 686 impulse responses were used: 14 antenna locations were selected, and at each location, 49 measurements were taken over an area of about 1 m2 . The Cassioli-Win-Molisch model is based on a discrete scale on the delay axis, with a delay bins defined with a step Δτ of 2 ns. The overall impulse response power received between the delays kΔτ and (k + 1)Δτ is integrated, and it is assumed that a ray exists at each delay kΔτ . This corresponds to a 1 . The power of each ray follows an exponential decay, ray arrival rate λ = Δτ

Statistical Modeling of the UWB Channel

161

but a single cluster is observed. Following the Saleh and Valenzuela formalism (see section 2.4.1), the PDP model can be expressed in the form: Ph (0, τ ) =

K  k=1

 βk2 δ

d τ − − (k − 1)Δτ c

 [5.8]

where d indicates the distance between the transmitter and the receiver. The PDP exponential decay is characterized by the coefficient γ (see equation [2.33]), but the model also introduces an additional coefficient r in order to account for a significant attenuation between the 1st ray and the 2nd ray. The propagation loss is characterized as a function of distance according to a dual-slope law: ⎧     ⎪ ⎪P L d0 + 20.4 log d + S(d) d ≤ 11 m ⎪ ⎨ d0 [5.9] P L(d) =   ⎪   d ⎪ ⎪ + S(d) d > 11 m ⎩P L d0 − 56 + 74 log d0 The fast fading due to the antenna displacement is characterized by a ray amplitude distribution following a Nakagami distribution (see Appendix B.1.3). The Nakagami m parameter decreases with the delay to approach the value of 1 for the last rays in the PDP, where the ray amplitude follows a Rayleigh distribution. This model provides an accurate and reproducible description of the observed measurements. Its main limitations lie in the low number of measurements on which the statistical study is based, and in the reduced frequency band. Frequency domain approach Most of the research efforts regarding statistical modeling for the UWB propagation channel concentrate on a time domain approach, where the model provides a description of the channel impulse response. However, other approaches are possible. The model proposed by the researchers from the AT&T Research Laboratory and MIT [GHA 04a] is an interesting example of a frequency domain approach. This model is designed from an extensive measurement campaign performed in 23 residential houses. The main concept of this model is to reproduce the channel transfer function T (f, t) in a statistical way. As for the time domain approach, each parameter

162

Ultra-Wideband Radio Propagation Channels

can be described using a statistical law. The value of the frequency domain approach lies in its opening up the possibility of describing the transfer function components in a regressive way. The model can be expressed in the form of a filter with infinite impulse response, which can be mathematically represented by:       [5.10] T fi , t + a1 T fi−1 , t + a2 T fi−2 , t = ni where ni represents the input white Gaussian noise. The model can be represented using five variables: the parameters a1 and a2 , the input conditions T (f1 , t) and T (f2 , t), and the standard deviation of the Gaussian noise σn . Each of these parameters is then described in a statistical way as a function of the distance. The model is complemented with a power attenuation law. Other approaches were proposed regarding UWB channel modeling in the frequency domain, such as the Prony method used by the Virginia Polytechnic Institute (USA) [LIC 03]. The value of such a model lies in its low complexity: only a few parameters are required for its description. However, there is no direct knowledge of the traditional channel characterization parameters, such as the shape of the PDP or the delay spread. For this reason, the comparison between the two model types is not straightforward. 5.2.2. Empirical modeling principles This section aims at illustrating UWB channel statistical modeling based on experimental data. A statistical model based on the Saleh and Valenzuela formalism is designed from the characteristic parameters observed in section 5.1 [PAG 06d]. The following sections present a propagation loss model and an impulse response model. Finally, simulation results are compared to the experimental measurements. 5.2.2.1. Propagation loss model The first step in the design of the UWB channel model is the definition of attenuation due to signal propagation. In section 5.1.1.1, it was shown that when the antenna effect is correctly compensated, the channel attenuation in the frequency domain is close to the theoretical loss of 20 dB per decade. The path loss model can thus be expressed in dB in the following form:       f d + 10Nd log + S(d) [5.11] P L(f, d) = P L f0 , d0 + 20 log f0 d0 where d0 = 1 m represents a reference distance, f0 = 6.85 GHz corresponds to the center frequency of the FCC analyzed band and S is a Gaussian random variable with zero mean. The parameters of this model are defined by experimental characterization (see section 5.1.1) and are given in Table 5.6.

Statistical Modeling of the UWB Channel

LOS

NLOS

Nd

1.62

3.22

σS (dB)

1.7

5.7

P L(f0 , d0 ) (dB)

53.7

59.4

163

Table 5.6. Path loss model parameters. Values of P L(f0 , d0 ) are given for f0 = 6.85 GHz and d0 = 1 m

5.2.2.2. Modeling the channel impulse response over an infinite bandwidth The principle of the UWB impulse response model consists of generating all constituent rays while maintaining the characteristics observed from the experimental measurements. Among these characteristics, we mainly aim at reproducing the clustering of multipath echoes, the ray and cluster arrival rates, and the decreasing magnitude of the received power with increasing delay. For a baseband representation, a ray is described by its delay τ , its amplitude β and its phase θ. By generating these parameters, it is possible to describe the impulse response over an infinite bandwidth. We then process these parameters in the frequency domain in order to include the effect of the limited observation bandwidth. In order to account for the clustering of multiple paths, the impulse response is modeled using the Saleh and Valenzuela formalism (see section 2.4.1). At a given instant, the UWB channel impulse response is thus described by the following formula: h(τ ) =

Kl L  

  βk,l ejθk,l δ τ − Tl − τk,l

[5.12]

l=1 k=1

where L represents the number of clusters, Kl is the number of rays within the lth cluster and Tl corresponds to the arrival time of the lth cluster. The parameters βk,l , θk,l and τk,l represent the amplitude, phase and arrival time associated with the k th ray within the lth cluster. The experimental observations given in section 5.1.2.3 show that the inter-clusters duration follows an exponential distribution. Hence, the arrival of a new cluster can be modeled by a Poisson process, and the number of clusters in the impulse response can be generated by drawing a random variable L according to the following law [MOL 04]: pL (L) =

¯ L exp(−L) ¯ (L) L!

[5.13]

164

Ultra-Wideband Radio Propagation Channels

¯ represents the average number of clusters. During measurement where L ¯ = 5.6 in the LOS analysis, we observed an average number of clusters of L ¯ case and L = 2.4 in the NLOS case. Having selected a transmitter-receiver distance d for the simulation, the time of arrival of the first cluster is given by T1 = dc , where c is the speed of light. The time of arrival Tl of the L − 1 remaining clusters is then calculated by generating inter-cluster durations following an exponential law [SAL 87]:      [5.14] p Tl | Tl−1 = Λ exp − Λ Tl − Tl−1 where Λ is the cluster arrival rate. The inter-cluster power decay is accurately modeled by a power function (see section 5.1.2.2). This approach differs from the one followed by Saleh and Valenzuela [SAL 87], but presents a closer fit to the experimental measurements. The amplitude of the first ray within each cluster is thus given by:  −Ω Tl 2 2 [5.15] β1,l = β1.1 T1 where Ω represents the inter-cluster power decay constant. In accordance to the results of the static UWB channel study, it is recommended to use the values Λ = 36.5 MHz and Ω = 4.4 in the LOS case. In the NLOS case, the recommended values are Λ = 24.9 MHz and Ω = 3.9. The rays are iteratively generated for each cluster. The arrival time of each ray is calculated using inter-ray durations following an exponential law [SAL 87]:      [5.16] p τk,l | τk,l−1 = λ exp − λ τk,l − τk,l−1 A power function is used to calculate the ray amplitude (see section 5.1.2.2):  −ω G τk,l + Tl 2 2 = 10− 10 β1,l [5.17] βk,l Tl where ω represents the intra-cluster power decay constant and G accounts for the observed attenuation between the first path of each cluster and the following multipaths. For each cluster, the ray generation stops when the ray amplitude reaches a given threshold D, fixed at −50 dB. According to the characterization study presented in section 5.1 and to the observation of the measured PDP, we recommend using the parameters λ = 5.95 GHz, ω = 11.1 and G = 12 dB in the LOS case. The recommended values in the NLOS case are λ = 6.19 GHz and ω = 10.2.

Statistical Modeling of the UWB Channel

165

Finally, the phase θk,l of each ray is generated using a uniform law over the interval [0, 2π[. This approach was also adopted in the IEEE 802.15.4a model [MOL 04]. Figure 5.16 presents the rays obtained in a LOS situation for a transmitter-receiver distance of 6 m, where we may observe 5 clusters. It may be noted that this representation corresponds to an infinite observation bandwidth, each ray being represented by a Dirac function.

Relative power (dB)

0 -10 -20 -30 -40 -50

0

20

40

60 Delay (ns)

80

100

Figure 5.16. Impulse response simulated over an infinite bandwidth. LOS situation, with the parameters d = 6 m, Λ = 36.5 MHz, λ = 5.95 GHz, Ω = 4.4, ω = 11.1 and G = 12 dB

Table 5.7 summarizes all experimental parameters used in our statistical model of the UWB channel. LOS

NLOS

fmin (GHz)

3.1≤ fmin < fmax

fmax (GHz)

fmin < fmax ≤ 10.6

D (dB)

50

Λ (MHz) ¯ L

36.5

24.9

5.6

2.4

λ (GHz)

5.95

6.19

Ω

4.4

3.9

ω

11.1

10.2

G (dB)

12

0

Table 5.7. Parameters of the UWB impulse response model

166

Ultra-Wideband Radio Propagation Channels

5.2.2.3. Modeling the channel impulse response over a limited bandwidth In practice, impulse response is observed on a limited bandwidth, situated within the 3.1–10.6 GHz band. We note by fmin and fmax the minimum and maximum frequencies in the observation band, and by fc = 12 (fmin + fmax ) the center frequency. The channel transfer function limited to the observation bandwidth hence appears (for positive frequencies): ⎧ Kl L   ⎪ 1 ⎨fc βk,l ej(θk,l −2πf (Tl +τk,l )) if fmin ≤ f ≤ fmax 'L 'Kl 2 Tlim (f ) = f β k=1 k,l l=1 k=1 l=1 ⎪ ⎩ 0 otherwise [5.18] where the coefficient

P L(fc ,d) ' L ' Kl 2 l=1 k=1 βk,l

normalizes the power received at the

frequency fc according to the proposed path loss model. In addition, the term ffc accounts for the power decrease in −20 log(f ) described previously. This transfer function normalization procedure was also proposed in [FOE 03a, ALV 03]. The impulse response observed over a limited bandwidth hlim (τ ) is simply obtained from the transfer function Tlim (f ) using an inverse Fourier transform. In order to limit the side lobes level, it is possible to use a Hanning window for instance at this stage [HAR 78]. Figure 5.17(a) represents an impulse response example observed over the 3.1–10.6 GHz frequency band. We may note that the low delay between two consecutive rays (see Figure 5.16) naturally induces constructive or destructive interferences. Figure 5.17(b) presents the same impulse response observed over 3.1–4.1 GHz frequency band: we may note that the multipath resolution is less accurate when the observation bandwidth decreases. 5.2.2.4. Simulation results A series of simulations was conducted using the static UWB radio channel model presented in section 5.2.2. A set of 119 PDP was generated using the same transmitter-receiver distances as in our measurement campaign (see section 3.4.2.1), for the LOS and NLOS situations. Each PDP was calculated from a set of 90 impulse responses, simulating the motion of the antenna around a circle of radius 20 cm. The generation of the fast fading characteristics for the 90 locally simulated impulse responses was performed using an advanced algorithm, taking the ray arrival angle into account. This algorithm is fully described in section 5.3.1. Figure 5.18 presents two typical PDP obtained by simulation. One of the 90 constituting impulse responses is also represented. Note that on the x-axis,

Statistical Modeling of the UWB Channel

167

(a) -60 Relative power (dB)

-70 -80 -90 -100 -110 -120 -130

0

20

40

60 Delay (ns)

80

100

80

100

(b) -60 Relative power (dB)

-70 -80 -90 -100 -110 -120 -130

0

20

40

60 Delay (ns)

Figure 5.17. Impulse response simulated over a limited bandwidth. Identical set of rays, observed over the 3.1–10.6 GHz band (a) and the 3.1–4.1 GHz band (b)

the delay was converted in path length. As a general observation, simulations are similar to the measured PDP (see Figure 5.3). Two parameters representative of the channel temporal dispersion were calculated for the entire set of generated PDP: the delay spread τRM S and the 75% delay window W75% . The average values obtained for these parameters in measurement and simulation are compared for the LOS and NLOS situations in Table 5.8. We may note that the proposed model correctly reproduces the dispersion parameters experimentally measured over the UWB radio channel. The delay spread of the simulated PDP is particularly close to the measurement, in both LOS and NLOS configurations. The values obtained for the delay window are somewhat different from the experimental data, but stay in the same range as the measured characteristics. The proposed model therefore allows us to reproduce not only the impulse response structure, but also channel dispersion.

168

Ultra-Wideband Radio Propagation Channels

(a)

Relative power (dB)

0

IR PDP

-10 -20 -30 -40 -50

0

20

40 Distance-delay (m)

60

80

(b)

Relative power (dB)

0

IR PDP

-10 -20 -30 -40 -50

0

20

40 Distance-delay (m)

60

80

Figure 5.18. PDP and impulse responses obtained by simulation. (a) LOS and (b) NLOS configurations

LOS

NLOS

Parameter

Measurement

Simulation

Measurement

Simulation

τRMS (ns)

4.1

4.0

9.9

9.7

W75% (ns)

7.6

9.7

23.7

21.2

Table 5.8. Comparison of the dispersion parameters: measurement vs. simulation

Statistical Modeling of the UWB Channel

169

5.3. Advanced modeling in a dynamic configuration Section 5.2.2 describes how to simulate an impulse response from statistical parameters obtained through experimental measurements, in the case of a static channel. In instances of practical use for future UWB systems, the antenna displacement or the motion of people may generate significant variations in the channel impulse response. This section describes two adaptations to the statical model for an advanced modeling of the spatial and temporal fluctuations of the UWB radio channel [PAG 06c]. 5.3.1. Space variation modeling Spatial variations are due to the displacement of at least one of the transmitting or receiving antennas. In this case, the lengths of most propagation paths undergo significant variation. Only a few studies on the statistical modeling of the UWB channel spatial variations are available. The IMST model is one example where a simplified ray tracing algorithm is used to calculate a fixed delay variation for each cluster [KUN 03]. We here propose to model these spatial fluctuations by taking the angle formed between the antenna motion and each propagation path into account. In the remainder of this section, we will assume a displacement of the receiving antenna and consider the arrival angle of each path. For the sake of clarity, the presented model allows an antenna displacement in the (O, x, y) plane only, by taking the ray azimuth ϕ into account. A 3D model including ray elevation is forwardly derivable. The first step of this spatial fluctuation model consists of generating an impulse response over an infinite bandwidth h(x0 , y0 , τ ), corresponding to a location (x0 , y0 ), as described in section 5.2.2. This impulse response observed over an infinite bandwidth may be expressed as in equation [5.12]. In order to calculate the impulse response observed over an infinite bandwidth at a location (x, y) close to the location (x0 , y0 ), we consider that each ray corresponds to a plane wave. This assumption holds when the receiving antenna is placed in the far field with respect to the surrounding walls and furniture where the transmission, reflection or diffraction phenomena occur. Figure 5.19 illustrates the obtained configuration for a given ray. The path elongation Δl of the incident ray is given by:     [5.19] Δl = − x − x0 cos(ϕ) − y − y0 sin(ϕ) where ϕ represents the incident ray azimuth. A limited number of statistical studies are available in the literature regarding the departure and arrival angles for UWB channels [CRA 02,

170

Ultra-Wideband Radio Propagation Channels

y r ij Į (x0, y0)

x

Figure 5.19. Path elongation related to an antenna displacement

HAN 05, VEN 05]. To determine the azimuth of each ray in the impulse response, we can use the model derived by Spencer et al. from wideband indoor measurements [SPE 97]. In this model, the arrival azimuth of the k th ray within the lth cluster is decomposed in Φl + ϕk,l , where Φl is the mean arrival azimuth in the lth cluster. Without further knowledge about the environment, we may consider that Φl is uniformly distributed in the [0, 2π[ interval. ϕk,l represents the distribution of the ray azimuth within a cluster, and follows a Laplace distribution with zero mean and standard deviation σϕ : 

pϕk,l ϕk,l



1 −| =√ e 2σϕ

√

2ϕk,l σϕ

|

[5.20]

In [HAN 05], the standard deviation of the arrival azimuth σϕ is lower than or equal to 6.7◦ .3 As a first approximation, we recommend using this value for the parameter σϕ . This value could be refined as more experimental data becomes available. For instance, [VEN 05] proposes a 2-cluster model, where the azimuth distribution follows a Laplace law in the first cluster (σϕ = 5◦ ) and a uniform law in the second cluster. From the impulse response generated at the location (x0 , y0 ) and knowing the arrival azimuth Φl + ϕk,l of each ray, we can calculate the transfer function

3. For the indoor LOS and NLOS configurations on a single floor.

Statistical Modeling of the UWB Channel

171

over a limited bandwidth at a location (x, y) close to location (x0 , y0 ): Tlim (x, y, f ) ⎧ Kl L   ⎪ 1 ⎨fc βk,l ej(θk,l −2πf (Tl +τk,l +Δτk,l )) 'L 'Kl 2 = f β l=1 k=1 k,l l=1 k=1 ⎪ ⎩ 0

if fmin ≤ f ≤ fmax otherwise [5.21]

with: Δτk,l = −

       1  x − x0 cos Φl + ϕk,l + y − y0 sin Φl + ϕk,l c

[5.22]

The impulse response hlim (x, y, τ ) observed over a limited bandwidth is simply obtained using an inverse Fourier transform. Figure 5.20 presents a simulation of the space varying impulse response observed over the 3.1–10.6 GHz band. The delay, amplitude and phase of each ray correspond to the parameters already used in the previous examples. The spatial variations of the impulse response were calculated for a displacement of the receiving antenna along the Ox axis over a distance of 2 m with 1 cm step. We may clearly distinguish the evolution of the main echoes (a-e), depending on their arrival direction. For instance, the length of the first path shortens from approximately 6 m to 4 m. 0

0 -5

(a)

5

10 (b)

-15 -20

15 (c) -25 20 (d)

-30

Relative power (dB)

Distance-delay (m)

-10

-35 25 -40

(e) 0

50

100 Location x (cm)

150

200

-45

Figure 5.20. Simulation of a space variant impulse response. Displacement of the receiving antenna along the Ox axis over a distance of 2 m

172

Ultra-Wideband Radio Propagation Channels

5.3.2. Modeling the effect of people This section describes a method to model the effect of people, based on the experimental analysis given in section 5.1.4. The main idea is to reproduce the time variance observed on each ray of a given impulse response. This model is based on the results of a real time UWB measurement campaign performed over the 4–5 GHz band (see section 3.4.2.3). As a result, the presented model is valid for simulating UWB channels with bandwidths up to 1 GHz only. However, the modeling methodology may be used in other configurations as more experimental characteristics of the time-variant UWB channel will become available. The extension of the model to temporal variations is based on an initial impulse response h(t0 , τ ) corresponding to a static environment at a given instant t0 . The method described in section 5.2.2 can be used to obtain a description of the impulse response over an infinite bandwidth. The initial impulse response can thus be expressed according to equation [5.12], where αk,l (t0 ) = βk,l eθk,l denotes the initial complex magnitude of the k th ray within the lth cluster. As observed in our experimental characterization, we will differentiate between (a) the main path of each cluster, where each person generates a shadowing pattern in addition to fast amplitude fluctuations, and (b) the clusters of dense multipath where Rayleigh fading occurs [PAG 06a]. When observing a radio channel over a relatively low bandwidth, in our case lower than 1 GHz, the observed main path encompasses not only the first ray in each cluster, but also several rays situated within the observation resolution R. This resolution R is equal to 2 ns for a bandwidth of 1 GHz when using a Hanning window [HAR 78]. For all rays within the main path of each cluster, the time-variant amplitude αk,l (t) is generated according to the algorithm below. A more detailed description of this algorithm may be found in [PAG 05]. Assuming that a group of Np people is interfering with the UWB radio link, the algorithm steps are as follows: i) Select Np instants {tn }n=1...Np corresponding to the instants where each of the Np people are crossing the main path of the cluster. These passing instants may be randomly chosen, or calculated according to the environmental geometry. ii) Generate Np slow shadowing patterns {sn (t)}n=1...Np corresponding to the individual effects of Np moving people, using the following Gaussian-shaped attenuation function: (  )  2 2  [5.23] sn (t) = −As exp − 2 t − tn Ts

Statistical Modeling of the UWB Channel

173

where As represents the maximal shadowing attenuation in dB, Ts represents the shadowing duration in seconds, and tn represents the shadowing instant. According to our experimental characterization, the parameter values may be selected in the range of 5 dB to 10 dB for As , and in the range of 3 s to 5 s for Ts . iii) Calculate the amplitude variations of the dominant component dl (t) in the linear scale as follows: dl (t) =

Np 

10

sn (t−tn ) 20

[5.24]

n=1

iv) Generate additional fast fading fluctuations rk,l (t) following a Rayleigh amplitude distribution and having a Laplacian scattering function. As observed from the experimental data, the Doppler spread νRMS should be in the range of 1–3 Hz. The mean power Pr of the random component rk,l (t) should be 8 dB to 13 dB below the power level of the dominant component αk,l (t0 ). v) Finally, calculate the time-variant amplitude αk,l (t) for rays within the main path of the lth cluster as:   αk,l (t) = αk,l t0 dl (t) + rk,l (t) [5.25] Regarding step iv), several methods for the generation of a random signal presenting a Rayleigh distribution and an arbitrary Doppler spectrum are thoroughly discussed in [PAE 02]. The algorithm presented above allows us to generate the effect that moving people have on the main path of each cluster. For the remaining rays, corresponding to regions of dense multipath, we propose to model the amplitude αk,l (t) variations by using a Rayleigh distribution. More experimental analysis should be performed to study the exact shape of the Doppler spectrum in the regions of dense multipath. As a first step, we propose using a Laplacian distribution. Thus, the amplitude αk,l (t) may be generated as in step iv) of the algorithm. Having calculated the amplitude αk,l (t) for all impulse response rays, the time variant transfer function is given as: Tlim (t, f ) ⎧ Kl L   ⎪ 1 ⎨ fc αk,l (t)e−j2πf (Tl +τk,l ) 'L 'Kl 2 = f β l=1 k=1 k,l l=1 k=1 ⎪ ⎩ 0

if fmin ≤ f ≤ fmax otherwise [5.26]

174

Ultra-Wideband Radio Propagation Channels

The impulse response hlim (t, τ ) observed over a limited bandwidth is obtained using an inverse Fourier transform. The proposed model was used to simulate the motion of 4 people in the vicinity of a radio link in a LOS situation. For selected realistic passing instants with respect to the main path of each cluster, the delays Tl and the passing instants tn were calculated using a ray tracing tool, from which only the most significant rays were extracted. Figure 5.21 illustrates the simulation configuration. The five selected paths correspond to the main path and to the reflections on the four walls. The dashed arrow indicates the motion of the group of 4 people and circles present locations where the group crosses one of the main echoes.

Rx

Tx

Figure 5.21. Simulation configuration for the effect of people

The time varying impulse response was simulated according to this information, and the results are presented in Figure 5.22. The impulse response is observed over the 4–5 GHz frequency band, as in an experiment. The following parameter values were used for the temporal variations model: As = 5 dB, Ts = 4 s, Pr = −13 dB and νRMS = 1 Hz. As indicated by the circle locations on the graph, the group of people interferes with each main path at a different instant. For each shadowing instant, we may observe a power attenuation of the corresponding path, for a duration in the order of 3 s to 6 s. In addition, the presence of mobile people generates fast fading, observable at all impulse response delays. It can be noted that on occasions, this fast fading significantly interferes with the main paths, as for instance on the second cluster. This proposed model could be refined by analyzing additional experimental results. In particular, further research could be conducted by sounding the UWB channel over a larger bandwidth.

Statistical Modeling of the UWB Channel

175

Figure 5.22. Simulation of a time variant impulse response. Circles indicate the group passing instants for the five main paths of the impulse response

5.4. Conclusion Statistical modeling of the UWB channel consists of reproducing the main channel characteristics observed during the measurements using a mathematical description. The experimental analyses described in this chapter illustrated the characterization of the UWB propagation channel in an indoor office environment. Path loss was analyzed in both frequency domain and distance domain. The measured PDP were characterized through the delay spread, as well as the arrival rate and amplitude decay of the rays and clusters. The fast fading analysis shows that the signal amplitude received at a given delay follows a Rayleigh distribution, except for the main paths, where the situation is more deterministic. Several models of the UWB propagation channel were presented in the literature. Among the statistical models, the proposals presented in the standardization groups IEEE 802.15.3a and IEEE 802.15.4a, based on a Saleh and Valenzuela approach, are frequently used for the analysis of UWB communication systems. The principles of statistical modeling were presented using a practical approach based on experimental data. The described path loss model can be used directly for dimensioning studies and to evaluate the jamming generated by an UWB terminal. A detailed model has also been given for the static impulse response. Simulations show that this model accurately reproduces the channel dispersion. It can be used in system simulations, for the design and development of UWB based radio transceivers.

176

Ultra-Wideband Radio Propagation Channels

Two extensions of the impulse response were finally described to account for the spatial and temporal variations of the UWB channel. The spatial variations model emulates the effects of antenna displacement, by including the arrival direction of the delayed wavefronts. The temporal fluctuations model integrates the effects linked to the motion of people, and can be used to simulate a UWB radio link in realistic conditions.

Appendix A

Baseband Representation of the Radio Channel

A real signal x(t) with spectral components covering a bandwidth centered on the frequency f0 = 0 can be represented by its complex envelope γx (t) defined by: 

[A.1] x(t) =  γx (t)ej2πf0 t There are several ways to define a complex envelope γ(t) able to represent the signal x(t) according to relation [A.1]. We will use here the complex envelope defined by the analytical form of the signal x(t) as follows [BAR 95]: γx (t) = x(t)e−j2πf0 t

[A.2]

where x(t) is the analytical representation of signal x(t). A real signal possesses a complex spectral structure with a Hermitian symmetry. All the information concerning this signal is known in the positive part of the frequency spectrum. The analytical signal is the signal representation using only its positive spectral frequency components. In order to keep the same signal power, the power spectral density (PSD) of the spectrum’s positive side is multiplied by two. The obtained analytical signal is thus defined in the frequency domain by:

   [A.3] X(f ) = F x(t) = 2U (f )X(f ) = 1 + sign(f ) X(f ) where F{·} is the Fourier transform operation and U (f ) represents the unit step function (Heaviside step function).

178

Ultra-Wideband Radio Propagation Channels

By using the inverse Fourier transform, it leads to the following relation: x(t) = x(t) + j

 1 ⊗ x(t) = x(t) + jH x(t) πt

[A.4]

where ⊗ represents the convolution operator and H{·} represents the Hilbert transform. The signal s(t) is obtained after a convolution of e(t) and h(t): s(t) = e(t) ⊗ h(t)

[A.5]

By keeping the same notations as previously, we have [BAR 95]: S(f ) = 2U (f )S(f ) = 2U (f )E(f )H(f ) = and then:

1 E(f )H(f ) 2

 γs (t) = s(t)e−j2πf0 t = F −1 S(f + f0 )   1 E(f + f0 )H(f + f0 ) = F −1 2 =

[A.6]

[A.7]

1 γe (t) ⊗ γh (t) 2

There is a second way to represent the equivalent baseband filter [GUI 96]. Indeed, relation [A.6] allows us to write: S(f ) = E(f )H(f ) So, γs (t) can also be expressed by:

    γs (t) = F −1 E f + f0 H f + f0   = γe (t) ⊗ h(t)e−j2πf0 t

[A.8]

[A.9]

So, the baseband filtered heq (t) which is equivalent to the real band filter h(t) can be expressed in two ways: heq1 (t) =

1 γh (t) 2

heq2 (t) = h(t)e−j2πf0 t

[A.10]

Baseband Representation of the Radio Channel

179

In the frequency domain, these two baseband filters Heq (f ) equivalent to the real band filter H(f ) are expressed by:     Heq1 (f ) = U f + f0 H f + f0 [A.11]   Heq2 (f ) = H f + f0 From a practical viewpoint, the filter Heq1 (f ) corresponds to a translation of the positive side frequency components of the filter H(f ) so that they are centered around 0 Hz. The filter Heq2 (f ) corresponds to a simple translation of all the filter component H(f ). These filters are similar when they are applied to signals expressed in baseband.

This page intentionally left blank

Appendix B

Statistical Distributions

B.1. Definition This section defines the main distribution laws presented in the book. Unless otherwise mentioned, most of these laws are generally used to characterize the magnitude of the channel impulse response for a given delay. For each distribution of the random variable X, we give the probability density function (PDF) pX (x), the cumulative density function (CDF) F (x) = P (X ≤ x), the first and second order moments E[X] and E[X 2 ], and the variance V ar[X] when it can be simply expressed.

B.1.1. Rayleigh distribution The Rayleigh distribution [PAR 00] is defined from the parameter σ which is related to the standard deviation of the distribution by a constant value. ⎧x x2 ⎨ e− 2σ2 2 pX (x) = σ ⎩ 0

F (x) =

if x ≥ 0

⎧ x2 ⎨1 − e− 2σ2

if x ≥ 0

⎩ 0

otherwise "

E[X] =

[B.1]

otherwise

π σ 2

[B.2]

[B.3]

182

Ultra-Wideband Radio Propagation Channels

  E X 2 = 2σ 2   4−π σ2 Var[X] = 2

[B.4] [B.5]

B.1.2. Rice distribution The Rice distribution [PAR 00, LAU 94] is defined from two parameters, s and σ. ⎧   2 2 ⎪ ⎨ x e− x 2σ+s2 I0 xs if x ≥ 0 σ2 pX (x) = σ 2 ⎪ ⎩0 otherwise

[B.6]

where I0 represents the modified Bessel function of type 1. ⎧   ⎪ ⎨1 − Q s , x if x ≥ 0 σ σ F (x) = ⎪ ⎩0 otherwise

[B.7]

where Q is the Marcum function given by [MAR 60]:

∞

Q(x, r) =

ye−

x2 +y 2 2

r

" E[X] =

π |σ|L 12 2



I0 (xy)dy

s2 − 2 2σ

[B.8]

 [B.9]

where L 12 is the Laguerre function, the solution of the differential equation: x

1 dy d2 y + y=0 + (1 − x) dx2 dx 2   E X 2 = s2 + 2σ 2

[B.10] [B.11]

A typical parameter of this distribution is the parameter k expressed by: k=

s2 2σ 2

[B.12]

Statistical Distributions

183

Numerous estimators exist for the k parameter. The k parameter estimator considered in the book is the one based on the second and fourth order moments, and uses the following m parameter: 2 x2 m=  2 x4 − x2 

[B.13]

where (·) corresponds to the empirical mean value. So, k is expressed by [ABD 01]: 1 1− m [B.14] k 1 1− 1− m The Rice distribution tends to a Rayleigh distribution when s tends to 0. B.1.3. Nakagami distribution The Nakagami distribution [LAU 94] is defined from two parameters, m and Ω.

⎧ m mx2 ⎪ ⎨ 2m x2m−1 e− Ω m pX (x) = Γ(m)Ω ⎪ ⎩0

if x ≥ 0

[B.15]

otherwise

where Γ represents the Gamma function defined for x > 0 by: ∞ e−t tx−1 dt Γ(x) =

[B.16]

0

⎧   2 ⎪ ⎨γ mx , m if x ≥ 0 Ω F (x) = ⎪ ⎩0 otherwise

[B.17]

where γ represents the incomplete Gamma function defined for x > 0 by: a 1 e−t tx−1 dt [B.18] γ(a, x) = Γ(x) 0  " Γ m + 12 Ω [B.19] E[X] = Γ(m) m   E X2 = Ω [B.20]

184

Ultra-Wideband Radio Propagation Channels

Numerous estimators exist for the parameter m. The one used in the book is the following [ABD 00]: 2 x2  2 x4 − x2 

m

[B.21]

The Nakagami distribution tends to a Rayleigh distribution when m tends to 1.

B.1.4. Weibull distribution The Weibull distribution [LAU 94] is defined from the two parameters, a and b. * b abxb−1 e−ax if x ≥ 0 [B.22] pX (x) = 0 otherwise * b 1 − e−ax if x ≥ 0 F (x) = [B.23] 0 otherwise   1 − 1b [B.24] E[X] = a Γ 1 + b     2 2 E X 2 = a− b Γ 1 + [B.25] b

The Weibull distribution tends to a Rayleigh distribution when b tends to 2.

B.1.5. Normal distribution The normal distribution is defined from two parameters, the mean μ and the standard deviation σ. (x−μ)2 1 e− 2σ2 2πσ    1 x−μ F (x) = 1 + erf √ 2 2σ

pX (x) = √

[B.26] [B.27]

Statistical Distributions

where erf represents the error function defined by: x 2 2 erf(x) = √ e−t dt π 0

185

[B.28]

E[X] = μ  2 E X = μ2 + σ 2

[B.29]

Var[X] = σ 2

[B.31]

[B.30]

B.1.6. Log-normal distribution The log-normal distribution [WIE 03] is defined from two parameters, μ and σ. This distribution corresponds to the normal distribution of a signal complex envelope expressed in dB. ⎧ (10 log(x)−μ)2 ⎨ √ 10 − 2σ 2 e if x ≥ 0 2πxσ ln(10) pX (x) = [B.32] ⎩0 otherwise   ⎧  −μ ⎨ 1 1 + erf 10 log(x) √ F (x) = 2 2σ ⎩ 0 μ

1

σ

2

E[X] = 10 · 10 10 + 2 ( 10 )   μ σ 2 E X 2 = 10 · 102( 10 +( 10 ) )

if x ≥ 0

[B.33]

otherwise [B.34] [B.35]

We can estimate the parameters μ and σ by calculating the first and second moments of the variable expressed in dB:   E XdB = μ  2  E XdB = μ2 + σ 2   Var XdB = σ 2

[B.36] [B.37] [B.38]

B.1.7. Laplace distribution The Laplace distribution [SPE 97] is often used to model the arrival angle associated with the cluster rays. In the book, this distribution is also used to describe the Doppler spectrum observed on the fast variations of the signals

186

Ultra-Wideband Radio Propagation Channels

generated by moving people. This distribution is defined from two parameters, μ and σ. √ |x−μ| 2 1 pX (x) = √ e− σ 2σ   |x−μ|√2  1 F (x) = 1 + sgn(x − μ) e− σ 2

[B.39] [B.40]

E[X] = μ  E X 2 = μ2 + σ 2

[B.41]

Var[X] = σ 2

[B.43]



[B.42]

B.2. Kolmogorov-Smirnov goodness-of-fit test Considering an empirical CDF Fn (x) based on n samples and the theoretical CDF F0 (x) of the random variable from which the random draw is held, we can study the following variable: 

 [B.44] Dn = max Fn (x) − F0 (x) Figure B.1 illustrates the calculation of the variable Dn , for which the distribution has been studied by Kolmogorov [KOL 33]. For a decision threshold α and the critical value dα , we note: P (Dn > dα ) = α

[B.45]

P (Fn (x) − dα ≤ F0 (x) ≤ Fn (x) + dα , ∀x) = 1 − α

[B.46]

or:

The critical value dα has been tabulated for various values of α and n. We can demonstrate for example that for n > 80: 1

d0.05  1.3581 · n− 2 1

d0.01  1.6276 · n− 2

[B.47]

For a sample size n = 100, for example, we can conclude that the probability is: – 95% that F0 (x) is totally situated between F100 (x) − 0.13581 and F100 (x) + 0.13581;

Statistical Distributions

187

Fn(x) P(X ” x)

Dn

F0(x)

x

Figure B.1. Kolmogorov-Smirnov test: theoretical and empirical CDF

– 99% that F0 (x) is totally situated between F100 (x) − 0.16276 and F100 (x) + 0.16276. The Kolmogorov-Smirnov test consists of calculating the maximum deviation between an empirical CDF and a theoretical CDF, for a given decision threshold α: – if this deviation is smaller than the critical value dα , we conclude that the empirical CDF follows the same law as the theoretical CDF; – if this deviation is higher than the critical value dα , we conclude that the empirical CDF does not follow the same law as the theoretical CDF. Formally, a statistical decision process like the Kolmogorov-Smirnov test can lead to two types of errors. If the test erroneously concludes that the sample set does not follow the theoretical distribution law, we are faced with an error of type I. If the test erroneously concludes that the sample set follows the theoretical distribution law, we are faced with an error of type II. In the case of the Kolmogorov-Smirnov test, the type I probability of error is known (α), but the type II probability of error cannot be directly calculated. In other words, the probability of error is not known when we conclude that some samples follow a given law. So, this test is to be used sparingly.

This page intentionally left blank

Appendix C

Geometric Optics and Uniform Theory of Diffraction

C.1. Geometric optics C.1.1. Introduction Geometric optics (GO) have been developed for the analysis of light wave propagation which corresponds to high frequencies. In propagation problems, the GO is valid only for frequencies higher than 100 MHz. If we consider a monochromatic electromagnetic pulsation wave ω, the  s, ω) and magnetic field H(  s, ω) expressions at an observation electric field E( point P, the spatial position of which is defined by a vector s, correspond to the Maxwell equation expressed in an inhomogenous medium free from charges, with a permittivity (s) and a permeability μ(s) [PET 93] (see equation [C.1]). The Maxwell equations imply a time domain field dependence with e−jωt .  s, ω) + jωμ(s)H(  s, ω) = 0 ∇ × E(  s, ω) − jω(s)E(  s, ω) = 0 ∇ × H(    s, ω) = 0 ∇ · (s)E(    s, ω) = 0 ∇ · (s)E(

[C.1]

For a homogenous dielectric medium, the permittivity and the permeability are not dependent on the position ((s) =  and μ(s) = μ).

190

Ultra-Wideband Radio Propagation Channels

The study of propagation problems in homogenous media is conducted by using Helmholtz vectorial equations which are derived from Maxwell equations:  (s, ω) + k 2 U  (s, ω) = 0 ∇2 U

[C.2]

 (s, ω) the electric or magnetic field and k = ω √μ = 2π = 2π √r μr the with U λ λ0 wavenumber of the propagation medium. λ and λ0 are the wavelengths in the   propagation medium and in the free space respectively. r = r − j(r + 60σλ)   and μr = μr − jμr correspond to the relative permittivities and the permeabilities of the medium. The conductivity of the medium is represented by σ. C.1.2. Field locality principle In a homogenous medium, energy propagates on paths which are straight and orthogonal to the wavefront. These wavefronts are defined by the wave surfaces which are plane, spherical, cylindrical or any other shape. A group of rays is a beam or tube which starts and ends with two caustic segments (see AB and CD in Figure C.1). The energy carried by a ray is persistent in the time and space domains as well as in magnitude and phase.

Caustics φˆ

A

sˆ

ρ2

P(s)

P(0)

D B

θˆ

C

propagation direction

ρ1

s

Figure C.1. Ray tubes, caustics and local base

As there is always a scale for which a wave can be considered as locally plane, the properties of transverse electromagnetic plane waves can thus be generalized to all the electromagnetic waves [GAR 87]. This is the electromagnetic wave

Geometric Optics and Uniform Theory of Diffraction

191

locality principle. The electric and magnetic waves are strictly transverse to the propagation direction s. The electric field vector is in the plane orthogonal to  H,  s) is orthonormal, direct and the propagation direction. The trihedron (E, follows relation [C.3]. "  = E

μ  (H × s) 

[C.3]

 which The study can thus be restricted to the case of the electric field E ˆ ˆ is expressed in a local basis B = (ˆ s, θ, φ). This local basis depends on the propagation direction. For reasons of readability, a simplified notation is  with its adopted in the following text which allows us to mix up the vector E vectorial representation E.

C.1.3. Field expression in geometric optics According to the work of Luneberg and Kline, the electric field is expressed in GO by [GLO 99]: E(s) = A(s, ρ1 , ρ2 ) E(0) e−jkΨ(s) ⎡ ⎡ ⎤ ⎤ 0 0   E(s) = ⎣ Eθ (s) ⎦ = A s, ρ1 , ρ2 ⎣ Eθ (0) ⎦ e−jkΨ(s) Eφ (s) B Eφ (0) B

[C.4] [C.5]

A(s, ρ1 , ρ2 ) corresponds to the ratio between the field magnitudes E(s) and E(0). It is also called the divergence factor: " A(s, ρ1 , ρ2 ) =

ρ1 ρ2 (ρ1 + s)(ρ2 + s)

[C.6]

– s is the covered distance between P (0) and P (s). – Ψ(s) is a phase function at the observation point P (s) and is equal to s. – E(0) is the electric field at the point P (0). ρ1 and ρ2 are the two main curvature radii of the wavefront measured on the central ray at the reference point P (0). This point corresponds to the source position or the interaction point between the wave and a surface.

192

Ultra-Wideband Radio Propagation Channels

As the electric field is transverse to the propagation direction sˆ, the component along sˆ is zero. In the following, the field will be expressed in its basis B without its component along sˆ (see equation [C.7]):

 

 Eθ (0)  Eθ (s) = A s, ρ1 , ρ2 e−jks [C.7] E(s) = Eφ (s) B Eφ (0) B The curvature radii ρ1 and ρ2 vary along the ray trajectory. They have to be recalculated whenever the ray is obstructed because the interactions modify the ray trajectory. An interaction can be a reflection, a transmission (or double refraction) or a diffraction. C.1.4. Change of local basis Considering an electric field expressed in a given basis B1 , if the wave corresponding to this field undergoes an interaction, the field has to be expressed in a new local basis. This new local basis corresponds to the input basis B2 of the interaction. To obtain the new expression of the field, we need to use the basis change matrix MB1 →B2 (see equation [C.8]).

 

Eα2 (0) B1 →B2 Eα1 (0) =M [C.8] E(0) = Eβ2 (0) B Eβ1 (0) B 2

1

s1 , α ˆ 1 , βˆ1 ) and B2 = (ˆ s2 , α ˆ 2 , βˆ2 ) are the direct orthonormal bases in B1 = (ˆ which the incident field is expressed at the interaction input. MB1 →B2 is the transition matrix allowing us to express the incident field in the new basis. This matrix corresponds to a projection of the vectors α ˆ 1 and βˆ1 in the basis B2 : 

α ˆ2 · α ˆ1 α ˆ 2 · βˆ1 B1 →B2 [C.9] M = ˆ ˆ 1 βˆ2 · βˆ1 β2 · α C.1.5. Incident field The incident field is the field radiated by a source S in the direction of an observation point P placed at a distance si . The expression of this field is i r deduced from equation (C.7) by applying the transition matrix MB →B : 

i  i 

   i i  Bi →Br Ei (0) i E s   M = A s, ρ , ρ e−jks [C.10] Er si = 1 2 i i E⊥ (0) Bi si Br E⊥

Geometric Optics and Uniform Theory of Diffraction

193

ρi1 and ρi2 are the main curvature radii of the incident wavefront. si , eˆi , eˆi⊥ ) is a direct orthonormal local basis at the emission. It Bi = (ˆ corresponds to a basis described by the direction sˆi . If we consider a spherical frame, eˆi and eˆi⊥ can be assimilated to vectors eˆθ and eˆφ which form with sˆi a direct orthonormal basis. si , eˆr , eˆr⊥ ) is a direct orthonormal local basis at the receiver side. Br = (−ˆ It corresponds to the basis described by the direction −sˆi . If we consider a eφ which spherical frame, eˆr and eˆr⊥ can be assimilated to the vectors eˆθ and −ˆ ˆ i form with −s a direct orthonormal basis. i

r

MB →B is the transition matrix which allows us to express the incident field at the point P in the good basis. This matrix corresponds to a projection of the vectors eˆi and eˆi⊥ in the basis Br . 

  eˆr · eˆi eˆr · eˆi⊥ 1 0 Bi →Br M = [C.11] = r i 0 −1 eˆ⊥ · eˆ eˆr⊥ · eˆi⊥ Most of the time, we consider that the incident wavefront is spherical. So, the field is expressed by: Er (si ) =

i 1 Bi →Br i M E (0)e−jks si

[C.12]

C.1.6. Reflected field The reflected field is the field received at a point P after the reflection of a ray at a point Qr placed at a distance si from the source point S and at a distance sr to the point P (see Figure C.2). C.1.6.1. Expression of the reflected field in GO The expression of the reflected field Er (sr ) is derived from the fundamental expression of the field in GO (see equation [C.7]). The reflection law which comes from the Fermat principle defines the reflection point Qr . The incident sˆi and reflected propagation sˆr directions are fixed by the interaction surface by the normal vector n ˆ (see equation [C.13]) [MCN 90].   0 [C.13] n ˆ × sˆi − sˆr = ˆ The incidence and reflection planes are the same and the incidence angle θi and reflection angle θr are equal (see Figure C.2). The incidence plane is defined

194

Ultra-Wideband Radio Propagation Channels

P

S

sˆr

eˆ r eˆ i eˆ i⊥ local basis Bi

eˆ r⊥

local basis Br

nˆ

sˆi θi

θr Qr

tangent plane of a surface

Figure C.2. Incident and reflection local bases

by the normal n ˆ and the incident ray given by the vector sˆi . The reflection plane is defined by the normal n ˆ and the reflected ray is given by the vector sˆr . The use of the locality principle in the case of the reflected field corresponds to the introduction of a reflection dyad R which is expressed according to the reflection coefficients R and R⊥ by: 

R 0 [C.14] R= 0 R⊥ Thus, the reflected field Er (0) at the point Qr and defined in the basis B only depends on the dyad R and on the incident field Ei (si ) defined in the basis B at this same point. It is thus necessary to express the field in the correct si , eˆi , eˆi⊥ ). incident local basis Bi = (ˆ i

i

Er (0) = R MB→B

Ei (si )

[C.15]

ˆ corresponds to the orthonormal basis in In relation [C.15], B = (ˆ si , α, ˆ β) i i which the incident field E (s ) is defined. α ˆ and βˆ are an arbitrary couple i of orthonormal vectors, such that B is direct. The transition matrix MB→B allows us to describe the field Ei (si ) in the basis B i .   ˆ eˆi · βˆ eˆi · α B→B i [C.16] = i M eˆ · α ˆ eˆi · βˆ ⊥

⊥

Geometric Optics and Uniform Theory of Diffraction

195

The reflected field Er (sr ) at the observation point P is expressed in the sr , eˆr , eˆr⊥ ) by the equation [C.17]. The main curvature reflected local base B r = (ˆ r r radii ρ1 and ρ2 of the reflected wave depend on those of the incident wave. In the case of a planar surface, the following equalities are obtained: ρr1 = ρi1 and ρr2 = ρi2 .       i r Er sr = A sr , ρr1 , ρr2 RMB→B Ei si e−jks

[C.17]

C.1.6.2. Incident and reflected ray bases The local bases Bi and Br are defined according to the incident ray ˆ . In fact, eˆi and eˆr are parallel to propagation direction sˆi and the normal n the incidence and reflection planes, while eˆi⊥ = eˆr⊥ are orthogonal to the same planes (see Figure C.2). C.1.6.3. Reflection coefficients The dyad R depends on the reflection coefficient components which are parallel R and perpendicular R⊥ to the incidence plane (see equation [C.14]). These coefficients are for the phase and the magnitude changes introduced by the reflection phenomenon on each component of the field. For multi-layer interfaces with one or more layers, these coefficients have to be adapted in order to take the stratification into account. Equation [C.18] corresponds to the reflection coefficient in the case of a surface with a thickness e and a permittivity r . The permeability is considered to be set at 1. 

R,⊥ =

1 − e−2jδ e2jδ Γ,⊥ 1 − Γ2,⊥ e−2jδ e2jδ

[C.18]

Γ,⊥ are the Fresnel coefficients in the case of an infinite plane surface with a permittivity r : Γ =

r cos θi −

r − sin2 θi

r cos θi +

r − sin2 θi

cos θi −

r − sin2 θi

cos θi +

r − sin2 θi

Γ⊥ =

[C.19]

[C.20]

In the case of a perfect conductor surface (σ → ∞), the reflection coefficients are expressed with a phase difference multiple of π by: Γ = +1

Γ⊥ = −1

[C.21]

196

Ultra-Wideband Radio Propagation Channels 

δ = kr l and δ k0 d2 are the phase terms associated with the delays √ introduced by each reflected field (see Figure C.3). kr = k0 r corresponds to the wavenumber of the medium with permittivity r and l = e/ cos θt is the one-way distance in the medium. The incidence θi and refraction θt angles are defined by: 1 sin θt = √ sin θi r 0

[C.22]

0

r

Transmitted rays Reflected rays θi θt θi e Incident ray

0

r

0

d

d l

d = 2l sin θi sin θt

e

Figure C.3. Reflection of a plane wave on a dielectric interface with thickness e

The expressions of R,⊥ do not consider the possible roughness of the encountered surfaces (see equation [C.18]). The roughness is introduced by

Geometric Optics and Uniform Theory of Diffraction

197

multiplying the coefficients Γ,⊥ by the roughness factor ρ (see equation [C.23]) [BEC 87] [COC 05]. h is the height standard deviation in the rough interface. ρ = e−2(kr h cos θi )

2

[C.23]

C.1.7. Refracted and transmitted field The refracted (or transmitted) field is the received field at the point P after refraction (or multiple refractions) of a wave at the point Qt placed on an interface at a distance si of the source point S and at a distance st of the point P. S

eˆ i eˆ ⊥i local basis B

sˆ i

eˆ t

i

θi

θt

nˆ

Qt

eˆ ⊥t

sˆ t

local basis B

P

t

Tangent plane at the refraction surface

Figure C.4. Transmission and incidence local bases

C.1.7.1. Expression of refracted and transmitted field in OG The expression of the transmitted field Et (st ) at the observation point P, placed at a distance st of the transmission point, also follows from the GO field main expression (see equation [C.7]). The refraction law, also called the Snell-Descartes law, comes from the Fermat principle. It establishes the relation between the incidence angle θi and the transmission angle θt (see Figure C.4) at the interface and in the direction air → medium (see equation [C.22]). The Fermat principle implies that the incidence and transmission planes are the same and defined by the incident sˆi ray and transmitted sˆt ray directions, and the reflection surface normal

198

Ultra-Wideband Radio Propagation Channels

n ˆ . Identically to the reflection example, the transmission can be considered as a local phenomenon, so the transmitted field is expressed by introducing a transmission dyad T. This dyad is obtained according to the transmission coefficients (see equation [C.24]). 

T 0 [C.24] T=  0 T⊥ The field Et (0) after the transmission point Qt depends on the coefficient T and on the incident field Ei (si ) at this same point, taking care to define the si , eˆi , eˆi⊥ ) (see equation [C.25]). incident field in the incident local basis Bi = (ˆ   i Et (0) = TMB→B Ei si

[C.25]

ˆ corresponds to the orthonormal basis in which the incident B = (ˆ si , α ˆ , β) i i field E (s ) is defined. As in the reflected field case, the transition matrix i MB→B allows the expression of the incoming field Ei (si ) in the incident local basis B i . The transmitted field Et (st ) at the observation point P is expressed in the transmission local basis Bt = (sˆt , eˆt , eˆt⊥ ) by:       i t Et st = A st , ρt1 , ρt2 TMB→B Ei si e−jks

[C.26]

In the simple refraction case, st corresponds to the distance between P and Qt . As the point P is inside the interface, the propagation constant considers the propagation speed related to the dielectric properties at the interface. For a multiple refraction (or transmission), st corresponds to the distance between P and Qt at which the propagation distance in the interface is removed. This last distance is obtained for propagation in free space. Indeed, in the case of multiple refraction, the phase delay associated with propagation in the interface is directly introduced in T. The divergence of a transmitted ray is given by the following relation: !  t t t ρt1 ρt2 A s , ρ1 , ρ2 = [C.27] t (ρ1 + st )(ρt2 + st ) ρt1 is the first main curvature radius of the transmitted wave. Its expression is different from the case of simple refraction (see equation [C.28]) and the case

Geometric Optics and Uniform Theory of Diffraction

199

of double refraction (see equation [C.29]). ρt1 = ρi1 α−1

[C.28]

ρt1

[C.29]

=

ρi1

+ αl

ρt2 is the second main curvature radius of the transmitted wave. Its expression is also different from the case of the simple refraction [C.30] and the case of the second refraction [C.31] [PLO 03]. ρt2 = ρi2 α−1 ρt2 l=

e cos θt

=

ρi2

[C.30] 2

+ αγ l

1 α= √ r

γ=

[C.31] cos θi cos θt

[C.32]

C.1.7.2. Incident and transmitted ray bases ˆ The knowledge of the incident ray propagation direction sˆi and the normal n allows us to define the local bases Bi and Bt . In fact, eˆi and eˆt are respectively parallel to the incidence and transmission planes and eˆi⊥ = eˆt⊥ are perpendicular ˆ (see to the same planes. eˆi and eˆi⊥ are defined according to the normal n Figure C.2). eˆt⊥ is obtained from equation [C.33]. Generally, after a double refraction Bi and Bt are the same because sˆi = sˆt . eˆt = eˆt⊥ × sˆt

[C.33]

C.1.7.3. Transmission coefficient In the expression of the transmission dyad, the two components T and T⊥ are respectively the transmission coefficients parallel and orthogonal to the incidence plane. They correspond to the phase and magnitude changes introduced by the transmission phenomenon on each component of the field. In the case of a simple refraction and a plane surface, their expressions are given by equations [C.34] and [C.35]. Γ and Γ⊥ correspond to the Fresnel reflection coefficients defined at equations [C.19] and [C.20]. √ 1 + Γ 2 r cos θi = [C.34] T = √ r r cos θi + r − sin2 θi T⊥ = 1 + Γ⊥ =

2 cos θi cos θi +

r − sin2 θi

[C.35]

200

Ultra-Wideband Radio Propagation Channels

In the case of a double refraction (transmission), T and T⊥ are expressed by equation [C.36] (see Figure C.3). In [SAG 03], the expression of the transmission coefficient for an interface with more than two materials is proposed. T,⊥ =

   1 − Γ2,⊥ e−2jδ e2jδ 1 − Γ2,⊥ e−2jδ e2jδ

[C.36]

C.2. Uniform theory of diffraction C.2.1. Introduction Electromagnetic waves are continuous, in magnitude and phase, in the time and space domain. However, the GO does not ensure the total continuity field. It predicts areas where the field is zero (shadow zone). In 1953, Keller proposed a generalization of the GO in order to consider diffracted rays. This led to the birth of general diffraction theory (GTD) [KEL 62]. The GTD allows us to solve the problem of field existence in the shadow zone of the GO. However, it presents a singularity at the boundary between a lighted zone and a shadow zone. So in 1962, the theory has been completed by Kouyoumjian and Pathak in order to ensure the total field continuity in all space points [KOU 74]; henceforth we talk about UTD. Thereafter, Burnside and Burgener have proposed a formalism of the uniform theory of diffraction (UTD) in the case of the 3D diffraction on a corner of small thickness [BUR 83]. Other authors have also studied the simple diffraction, the double diffraction as well as the slope diffraction in the frequency domain [LUE 89, DES 84, ROU 96, ROU 99] and in the time domain [VER 90, ROU 95]. Then, only the expression of the diffracted field in the frequency domain is addressed, considering the case of the diffraction by dielectric or metallic dihedron.

C.2.2. Diffracted field The expression of the diffracted field given by equation [C.37] corresponds to the diffraction by a dihedron. For this kind of diffraction, the discontinuity line is mixed up with the one of the diffracted beam caustics and so the curvature radius ρd2 , also called minor ray, becomes zero.       i d Ed sd = A sd , ρd1 , ρd2 → 0 DMB→B Ei si e−jks

[C.37]

Geometric Optics and Uniform Theory of Diffraction

201

A(s) is the divergence factor of the ray diffracted by the dihedron and is expressed by: !   d d d ρd [C.38] A s , ρ1 , ρ2 → 0 =  d 1 d  d ρ1 + s s D is the dyad introducing the diffraction coefficients. This dyad can be written differently according to the diffracted ray’s nature, which can be two-dimensional (2D) or three-dimensional (3D). i

The matrix MB→B makes it possible to describe the incident field, initially expressed in the basis B, in the incidence basis of the diffraction sd , eˆi , eˆi⊥ ). The diffracted field Ed (sd ) is defined in the diffraction basis Bi = (ˆ d B = (ˆ sd , eˆd , eˆd⊥ ). The diffraction law, coming from the generalized Fermat principle, connects the Keller angle β0 to the incident ray direction sˆi and the diffracted ray direction sd as well as the tangent tˆ of the dihedron wedge (see Figure C.5) at the diffraction point Qd by: sˆi · tˆ = sˆd · tˆ = cos β0

[C.39]

The incidence and diffraction planes are thus defined by the tangent of the wedge tˆ and by the incident and diffraction ray directions. Generally, these two planes are not merged, as illustrated in Figure C.5. The vectors of the bases Bi and Bd are obtained using the following relations: tˆ si × eˆi⊥ = sˆi × eˆi eˆi = −ˆ sin β0 [C.40] tˆ d d d d d eˆ = sˆ × eˆ⊥ = sˆ × eˆ sin β0 C.2.3. UTD 2D coefficient In the case of a 3D ray, the dyad D is diagonal and directly expressed from the two components of the diffraction coefficients D and D⊥ : 

D 0 [C.41] D= 0 D⊥ The terms D and D⊥ are the diffraction coefficients initially introduced by Keller and then modified by Kouyoumjian, Burnside and Luebbers.

202

Ultra-Wideband Radio Propagation Channels

n tio ac r ff Di

tˆ Incidence plane

eˆ d⊥

β0

eˆ i

local basis Bd Qd

sˆi β0

eˆ i⊥

P

sˆd

eˆ d

local basis Bi

S

ne pla

φd

φi (2 − n)π

Figure C.5. Incidence and diffraction local bases

C.2.3.1. UTD coefficient – dihedron conductor Contrary to the GTD, the UTD introduced by Kouyoumjian and Pathak [KOU 74] ensures the field continuity in all the space, especially at the optic boundaries ISB (incident shadow boundary) and RSB (reflection shadow boundary). These authors have taken an interest in the case of a perfect conductor dihedron and have defined two new diffraction coefficients which introduce a correcting factor compared to the GTD coefficients:

D1 D2 D3 D4

D//,⊥ = D1 + D2 ± (D3 + D4 )  +  , e−j π + (φd − φi ) F kLa+ (φd − φi ) =− √ cot 2n 2n 2πk sin βo  +  π , e−j 4 π − (φd − φi ) F kLa− (φd − φi ) =− √ cot 2n 2n 2πk sin βo  +  π , e−j 4 π + (φd + φi ) √ F kLa+ (φd + φi ) =− cot 2n 2n 2πk sin βo  +  π , e−j 4 π − (φd + φi ) F kLa− (φd + φi ) =− √ cot 2n 2n 2πk sin βo

[C.42]

π 4

[C.43]

Geometric Optics and Uniform Theory of Diffraction

203

β0 is a semi-angle at the diffraction cone head. The normal incidence corresponds to βo = π2 (see Figure C.5). φi and φd are respectively the incidence and diffraction angles. They are specified from the wedge face 0 (see Figure C.5). n is a parameter defined so that the dihedron inner angle is given by (2−n)π. ± corresponds to the reflection coefficient in the case of a conductor [C.21]. F (x) corresponds to the transition function which uses the Fresnel integral [LEG 95]: √

jx

F (x) = 2j xe

∞

√

2

e−jt dt

[C.44]

x

L is a distance parameter which corresponds to the incidence type on the wedge. It brings into play the incident wave main curvature radii (ρd1 and ρd2 ) as well as the wedge of curvature radius (ρde ) (see equation [C.45]). In the case of a spherical wave, L is given by equation [C.46]. L = sin2 β0 sd

ρde + sd ρd1 ρd2 d d d d ρe ρ1 + s ρ2 + sd

L = sin2 β0

sd ρd1 + sd

ρd1

[C.45] [C.46]

a± is a function defined by: a± = 2 cos2

 2nπN ± − (φd ± φi )  2

[C.47]

with N ± an integer corresponding (outside the optic boundaries) to relation [C.48]: 2πnN ± − (φd ± φi ) = ±π

[C.48]

When the cotangent (cot) of one of the Di (i = 1, 2, 3, 4) terms becomes singular for the optic boundary angles φi and φd , the corresponding term is √ L replaced by − 2 sign() [PLO 00].

204

Ultra-Wideband Radio Propagation Channels

C.2.3.2. UTD coefficients – dielectric dihedron Luebbers proposes a more general formulation for the diffraction coefficients. This formulation allows us to consider the dielectric nature of the wedge as well as its roughness [LUE 89]. These coefficients are heuristic solutions as they are not obtained by solving Maxwell equations:     n 0 [C.49] D3 + G0//,⊥ D2 + ρ0 R//,⊥ D4 D//,⊥ = Gn//,⊥ D1 + ρn R//,⊥ Di (i = 1, 2, 3, 4) are terms reported on equations [C.43]. 0,n corresponds to the Fresnel reflection coefficients [C.19] and [C.20]. R//,⊥ The incidence angles θi0 = π2 − φi and θin = π2 − (nπ − φi ) depend on the faces 0 and n of the considered wedge.

ρ0,n corresponds to the roughness coefficient of the considered face [C.23]. G0,n //,⊥ are the correcting coefficients which allow us to consider the grazing incidences on the faces 0 and n of a dihedron. ⎧ 1 ⎪ 0 ⎪ for φi = 0 and |1 + R//,⊥ |>0 ⎪ 0 ⎪ ⎨ 1 + R//,⊥ G0//,⊥ = 1 [C.50] ⎪ for φi = nπ ⎪ ⎪ 2 ⎪ ⎩ 1 otherwise ⎧ 1 ⎪ n ⎪ for φi = nπ and |1 + R//,⊥ |>0 ⎪ n ⎪ ⎨ 1 + R//,⊥ Gn//,⊥ = 1 [C.51] for φi = 0 ⎪ ⎪ ⎪2 ⎪ ⎩1 otherwise

C.2.4. UTD 3D coefficient Contrarily to the case of a 2D ray, the dyad D of a 3D ray is no longer diagonal and is expressed only by two diffraction coefficients, as in the case of 2D ray (see equation [C.49]). This 3D dyad has been introduced by Burnside and Burgener [BUR 83] and reused by Rouvi`ere [ROU 99] in the case of a dielectric half-plane with very small thickness. To obtain the 3D dyad of [BUR 83], field continuity has to be ensured at each optic limit. So, the boundary conditions at the reflection in incidence

Geometric Optics and Uniform Theory of Diffraction

205

boundaries have to consider relations [C.52] and [C.53]. In these relations, Ui and Ur correspond to the incident and reflected fields respectively. * d −1/2Ur area I e−jks = RU (Qd )D(φ + φ ) √ area II 1/2Ur sd * d     e−jks −1/2(1 − T)Ui area II (1 − T)Ui Qd D φd − φi √ = area III 1/2(1 − T)Ui sd i

d

i

[C.52]

[C.53]

with the areas denoted I, II and III illustrated by Figure C.6. RSB

Zone I incident + reflected + diffracted

Zone II incident + transmitted

ISB

Zone III diffracted + transmitted diffracted wedge

Figure C.6. Field area around a diffracting wedge

Using these boundary conditions, the following expression is obtained for the dyad D: D = (I − T )D(φd − φi ) + R D(φd + φi )

[C.54]

D(φd − φi ) = D1 + D2

[C.55]

D(φd − φi ) = D1 + D2

[C.56]

Each of the dyads (D, R and T ) are expressed in their respective local basis. It is thus necessary to calculate the base change matrices in order to express all the fields in the local basis of the diffraction. α is the angle between the incident-reflection plane as well as the incidence-transmission plane and the incident plane. The diffraction plane is given by π2 − α. In 2D,

206

Ultra-Wideband Radio Propagation Channels

the incidence-reflection and incidence-transmission planes are perpendicular to the incidence-diffraction plane (α = 0). In 3D, these planes have no particular direction (see Figure C.7).

ce den inci

ion flect - re e n pla

nˆ

−α eˆ i S

eˆ d⊥

θr

θi

sˆi

Qd β0

eˆ i⊥

ne pla

ne pla ce en cid In π 2

sˆd

eˆ d

n tio ac ffr Di

P

tˆ

φd

φi (2 − n)π

Figure C.7. Reflection and diffraction incidence planes

The relations between the reflection and diffraction local bases are illustrated at Figure C.8 allow us to establish the matrix of basis change necessary to express the reflection R (see equation [C.57]) and transmission T dyads in the diffraction local basis (see equation [C.57]). In these equations, the exponent terms correspond to the plane nature (i for incident and d for diffraction) as well as the interaction specifying the plane (r for reflection and d for diffraction). ⎡ MiR→D (α)

eˆi,d ˆi,r  ·e 

= M(α) = ⎣ i,d i,r eˆ⊥ · eˆ ⎡

MdR→D (α)

ˆd,r eˆd,d  ·e 

= M(−α) = ⎣ d,d d,r eˆ⊥ · eˆ

⎤

⎦ = cos α sin α eˆi,d · eˆi,r eˆi,d ˆi,r ⊥  ·e ⊥

⊥

eˆd,d ˆd,r ⊥  ·e eˆd,d ˆd,r ⊥ ·e ⊥

⎤ ⎦=



− sin α cos α

cos α − sin α



sin α cos α

[C.57]  [C.58]

Geometric Optics and Uniform Theory of Diffraction

eˆ i,d ⊥

eˆ i,r ⊥

eˆ d,d ⊥

α

207

eˆ d,r ⊥

α eˆ i,d  α

eˆ i,r 

eˆ d,d 

α

eˆ d,r  before diffraction

after diffraction

Figure C.8. Incidence reflection and diffraction bases in 3D case

In the case of transmission, the same basis change matrices are used. They are denoted M(−α) because we turn conversely. The dyadic matrices are thus expressed by R and T by using equations [C.59] and [C.60].  −1 R = MdR→D (α) R MiR→D (α) = M(−α) R M(−α) 

R cos2 α − R⊥ sin2 α (R + R⊥ ) cos α sin α = −(R + R⊥ ) cos α sin α R⊥ cos2 α − R sin2 α  −1 T = MdT →D (α)T MiT →D (α) = M(α)TM(−α) 

T cos2 α + T⊥ sin2 α (T − T⊥ ) cos α sin α =  (T − T⊥ ) cos α sin α T⊥ cos2 α + T sin2 α 

1 − T cos2 α − T⊥ sin2 α −(T − T⊥ ) cos α sin α (I − T ) = −(T − T⊥ ) cos α sin α 1 − T⊥ cos2 α − T sin2 α

[C.59]

[C.60]

[C.61]

Expressions [C.59] and [C.61] inserted in equation [C.54] underline the non-diagonal structure of the dyad D which is expressed by [BUR 83] [GLO 99]:

D=

Da Dc

Db Dd

 [C.62]

       Da = 1−T cos2 α−T⊥ sin2 α D φi − φd −[R cos2 α − R⊥ sin2 α D φi + φd [C.63]

208

Ultra-Wideband Radio Propagation Channels

Db = cos α sin α [(T⊥ − T ) D(φi − φd ) + (R + R⊥ ) D(φi + φd )]

[C.64]

Dc = cos α sin α [(T⊥ − T ) D(φi − φd ) − (R + R⊥ ) D(φi + φd )]

[C.65]

Dd = [1−T sin2 α−T⊥ cos2 α]D(φi − φd )−[R⊥ cos2 α−R sin2 α]D(φi + φd ) [C.66] In equations [C.63] [C.64] [C.65] and [C.66], the terms R,⊥ and T,⊥ are the reflection and transmission coefficients, the expressions of which are given by [C.18] and [C.36].

Appendix D

Ray Construction Techniques

D.1. Ray launching Ray launching is a forward approach which consists of sending rays in all the directions from a transmission position of coordinates (Tx) with an incremental angular step (Δα) which can be set to various values. Then, the receiver position coordinates (Rx) are specified (see Figure D.1) [CHE 96, KIM 97, STA 98, LIN 89]. The speed of ray determination with the ray launching approach is directly related to the chosen Δα. When the Rx position is fixed, the rays connecting the transmitter Tx and the receiver Rx are obtained considering a receiver sphere of diameter Δd which can be set to various values. So, the launched rays connecting Tx to Rx will be considered if they intersect the receiver sphere (see Figure D.1). The number of rays obtained increases with the sphere diameter Δd (for a given Δα), but the precision of the calculated field and the received signal decreases. D.2. Ray tracing Ray tracing is a backward approach which consists of applying the image principle from Tx and Rx position in order to obtain reflected rays (see Figure D.2) [HUM 03, MCK 91, CHA 03]. The specificity of this approach is the increase of the number of the potential images combinations with the complexity of the considered environment. This can lead to important ray calculation time.

210

Ultra-Wideband Radio Propagation Channels

δα

Tx

(a)

δα δd

Rx

Tx

(b)

Figure D.1. Ray launching principle: (a) rays launched from the transmitter and (b) rays obtained considering intersection of receiver sphere

    Im Im Tx /s1 /s2

  Im Tx /s1

s1 Tx

Rx

s2

Figure D.2. Ray tracing principle

Ray Construction Techniques

211

D.3. Other techniques In the literature, other techniques are also proposed and used for ray determination. Some of these techniques are hybrid and combine ray launching and ray tracing [TAN 95, TCH 03, AVE 04], while others require a visibility tree to be built [AGE 97, AGE 00], or rely upon calculation time speed improvement techniques borrowed from the image processing domain. These last techniques use octree, raster or Voxel matrices for ray determination [FOL 84, LEG 05].

This page intentionally left blank

Appendix E

Description of the Time-Frequency Transform

The determination of a time domain signal x(τ ) from its frequency domain expression X(f ) is generally made using an inverse Fourier transform (see equation [E.1]). As the frequency domain expression X(f ) of the signal x(τ ) shows a Hermitian symmetry (see equation [E.2]), the obtained signal x(τ ) is real. +∞ X(f ) ej 2 π f τ df [E.1] x(τ ) = −∞

∗

X (f ) = X(−f ) ∀ f ∈ R

[E.2]

From frequency domain measurements, the obtained channel transfer function H(f ) is defined on a finite frequency band from fmin to fmax , for Nf frequency points. As H(f ) is discrete, the determination of h(τ ) is made min using an inverse Fourier transform (see equation [E.3]). δf = fmaxN−f is the f frequency sampling step and fk corresponds to a frequency value given by fk = fmin + k δf . Nf −1

h(τ ) = δf



H(fk ) ej 2 π fk τ

[E.3]

k=0

The transfer function H(f ) does not show a Hermitian symmetry because it is only defined between fmin and fmax . The signal obtained after discrete inverse ˆ ) (see Figure E.1). Fourier transform is complex and corresponds to h(τ ) + j h(τ

40

50

10

20 30 delay (ns)

imaginary part

Figure E.1. Inverse Fourier transform of H(f )

0

−0.08

−0.08

20 30 delay (ns)

−0.06

−0.06

10

−0.04

−0.04

0

0

0.02

0.02

−0.02

0.04

0.04

0

0.06

0.06

−0.02

0.08

0.08

real part

40

50

214 Ultra-Wideband Radio Propagation Channels

Description of the Time-Frequency Transform

215

To obtain a real signal h(τ ), it is mandatory to use a transfer function H2 (f ) presenting by construction a Hermitian symmetry. Moreover, to improve the precision of the reconstructed h(τ ), we can expand the spectral support of H2 (f ) in comparison to H(f ). This consists of making an operation of zero padding. Indeed, the product δτ δf Nf is equal to 1, so the increase of Nf necessary leads to a reduction of δτ and consequently improves the time domain precision of the signal h(τ ) obtained after the discrete inverse Fourier transform. The reconstruction of a real h(τ ) from H(f ) is made by applying two successive operations on H(f ) before the discrete inverse Fourier transformation: zero padding and Hermitian symmetric forcing. Operation of zero padding The operation of zero padding consists of obtaining a new transfer function H1 (f ) from H(f ) (see Figure E.3). The new transfer function H1 (f ) contains far more samples than H(f ). H1 (f ) is constructed according to the following relation with fe = 2 1δτ . *   H(f ) f ∈ fmin , fmax     [E.4] H1 (f ) = 0 f ∈ δf, fmin − δf ∪ fmax + δf, fe So, the new transfer function H1 (f ) is constructed as shown in equation min max − 1 and Nr = fe −f . [E.5]) with N1 = Nr + Nf + Nl samples where Nl = fδf δf  H1 (f ) = zeros(1, Nl )

H(f )



zeros(1, Nr )

[E.5]

Figure E.2 shows the time domain signal obtained after discrete inverse Fourier transformation is applied on H1 (f ). We can notice that the sampling of the obtained time domain signal is improved. Nevertheless, it is still complex. Operation of Hermitian symmetric forcing The operation of forcing the Hermitian symmetry consists of creating a transfer function H2 (f ) from H1 (f ). This new transfer function H2 (f ) is defined from −fe to fe (see equation [E.6]) as illustrated in Figure E.3. Figure E.4 represents a real impulse response h(τ ) obtained after a discrete inverse Fourier transform applied on H2 (f ). * H2 (f ) = H1 (f ) for f > 0   [E.6] ∗ H2 (−f ) = H2 (f ) ∀f ∈ δf, fe

40

50

10

20 30 delay (ns)

imaginary part

Figure E.2. Zero padding and inverse Fourier transform on H1 (f )

0

−0.08

−0.08

20 30 delay (ns)

−0.06

−0.06

10

−0.04

−0.04

0

0

0.02

0.02

−0.02

0.04

0.04

0

0.06

0.06

−0.02

0.08

0.08

real part

40

50

216 Ultra-Wideband Radio Propagation Channels

−fe

−f max

0

f max

f min

f max

H (f ) + zero padding

f min

Figure E.3. Illustration of the Hermitian symmetric forcing

−f min

H *(f) + f lip zero padding

Operation of symmetric f orcing

±f

H (f ) + zero padding

fe f

fe f

Description of the Time-Frequency Transform 217

−0.04 −0.06 −0.08

−0.04

−0.06

−0.08 10

20 30 delay (ns)

imaginary part

Figure E.4. Reconstruction of h(τ ) after discrete inverse Fourier transform applied on H2 (f )

0

−0.02

−0.02

50

0

0

40

0.02

0.02

20 30 delay (ns)

0.04

0.04

10

0.06

0.06

0

0.08

0.08

real part

40

50

218 Ultra-Wideband Radio Propagation Channels

Bibliography

[ABD 00] Abdi A., Kaveh M., “Performance comparison of three different estimators for the Nakagami m parameter using Monte Carlo simulation”, IEEE Communications Letters, vol. 4, no. 4, p. 119–121, April 2000. [ABD 01] Abdi A., Tepedelenlioglu C., Kaveh M., Giannakis G., “On the estimation of the K parameter for the Rice fading distribution”, IEEE Communications Letters, vol. 5, no. 3, p. 92–94, March 2001. [AFF 00] Affandi A., Caract´erisation et mod´elisation de la propagation ` a l’int´erieur des bˆ atiments dans les bandes de 450 - 900 - 1800 - 2400 - 5800 MHz, PhD Thesis, Institut National des Sciences Appliqu´ees de Rennes, France, 2000. [AGE 97] Agelet A., Fontan F., Formella A., “Fast ray-tracing for microcellular and indoor environments”, IEEE Transactions on Magnetics, vol. 33, p. 1484–1487, March 1997. [AGE 00] Agelet A., Formella A., Rabanos J., De viente F., Fontan F., “Efficient ray tracing acceleration techniques for radio propagation modeling”, IEEE Transactions on Vehicular Technologies, vol. 49, p. 2089–2104, November 2000. [AIE 03a] Aiello R., Ellis J., Kareev U., Siwiak K., Taylor L., Understanding UWB – principles and implications for low-power communications, Report no. IEEE P802.15-03/157, IEEE P802.15 Working Group for WPANs, March 2003. [AIE 03b] Aiello R., Rogerson G. D., “Ultra-wideband wireless systems”, IEEE Microwave Magazine, vol. 4, no. 2, p. 36–47, June 2003. [ALV 03] Alvarez A., Valera G., Lobeira M., Torres R., Garcia J. L., “New channel impulse response model for UWB indoor system simulations”, IEEE Vehicular Technology Conference, VTC Spring, vol. 1, Seoul, Korea, p. 1–5, April 2003. [ART 95] Arthur J., “Modern SAW-based pulse compression systems for radar applications.I. SAW matched filters”, Electronics & Communication Engineering Journal, vol. 7, no. 6, p. 236–246, December 1995.

220

Ultra-Wideband Radio Propagation Channels

[ATT 03] Attiya A., Safaai-Jazi A., “Time domain characterization of receiving TEM horn antennas”, IEEE Antennas and Propagation Society International Symposium, Columbus, OH, USA, p. 233–236, June 2003. [ATT 04] Attiya M., Saffai-Jazi A., “Simulation of ultra-wideband indoor propagation”, Microwave and Optical Technology Letters, vol. 42, no. 2, p. 103–108, May 2004. [AVE 04] Aveneau L., Combeau P., “Path finding based on Monte Carlo techniques compared with a full ray-tracing approach in narrow and wide bands”, IEEE Vehicular Technology Conference, Milan, Italy, May 2004. [BAL 04a] Balakrishnan K., Wee K. C., Xu S., Chuan C. L., Chin F., Huat C. Y., Choy C. C., Thiang T. T., Xiaoming P., Ong M., Krishnan S., Characterization of Ultra-Wideband Channels: Small-Scale Parameters for Indoor & Outdoor Office Environments, Report no. IEEE 802.15-04/385, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), July 2004. [BAL 04b] Balakrishnan K., Wee K. C., Xu S., Chuan C. L., Chin F., Huat C. Y., Choy C. C., Thiang T. T., Xiaoming P., Ong M., Krishnan S., UWB Channel Characterization in Indoor Office Environments, Report no. IEEE 802.15-04/439, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), August 2004. [BAR 91] Barnes P., Teacher F., “On the direct calculation of a transient plane wave reflected from a finitely conducting half space”, IEEE Transactions on Electromagnetic Compatibility, vol. 33, no. 2, p. 90–96, May 1991. [BAR 95] Barbot J. P., Propagation radio´electrique avec les mobiles pour les communications personnelles ` a l’int´erieur des bˆ atiments dans la bande 1-3 GHz, PhD Thesis, Paris XI-Orsay University, France, 1995. [BAR 00] Barrett T. W., “History of ultrawideband (UWB) radar & communications: pioneers and innovators”, Progress in Electromagnetics Symposium, Cambridge, MA, USA, July 2000. [BAT 03] Bateman D., “RF aspects of ultra-wideband”, International Workshop on Ultra Wideband Systems, Oulu, Finland, June 2003. [BAT 04a] Batra A., Balakrishnan J., Dabak A., “Multi-band OFDM: a new approach for UWB”, International Symposium on Circuits and Systems, vol. 5, Vancouver, Canada, p. 365–368, May 2004. [BAT 04b] Batra A., Balakrishnan J., Dabak A., Gharpurey R., Lin J., Fontaine P., Ho J. M., Lee S., Frechette M., March S., Yamaguchi H., Foerster J., Molisch A. F., Multi-band OFDM physical layer proposal for IEEE 802.15 Task Group 3a, Report no. IEEE P802.15-03/268r3, IEEE P802.15 Working Group for Wireless Personal Area Networks (WPANs), March 2004. [BAY 04] Bayram A., Attiya A. M., Safaai-Jazi A., Riad S. M., “Frequency-domain measurement of indoor UWB propagation”, IEEE Antennas and Propagation Society Symposium, Monterey, CA, USA, p. 1303–1306, June 2004.

Bibliography

221

[BEC 87] Beckmann P., Spizzichino A., The Scattering of Electromagnetic Waves from Rough Surface, Artech House, 1987. [BEL 63] Bello P. A., “Characterization of randomly time-variant linear channels”, IEEE Transactions on Communication Systems, vol. 11, p. 360–393, December 1963. [BEN 66] Bendat J. S., Piersol A. G., Measurement and Analysis of Random Data, Wiley, New York, 1966. [BEN 78] Bennett C. L., Ross G. F., “Time-domain electromagnetics and its application”, IEEE Proceedings, vol. 66, no. 3, p. 299–318, March 1978. [BUE 03] Buehrer R. M., Davis W. A., Safaai-Jazi A., Sweeney D., “Characterization of the ultra-wideband channel”, IEEE Conference on Ultra Wide Band Systems and Technologies, Reston, VA, USA, p. 26–31, November 2003. [BUL 87] Bultitude R. J. C., “Measurement, characterization and modeling of indoor 800/900 MHz radio channels for digital communications”, IEEE Communications Magazine, vol. 25, no. 6, p. 5–12, June 1987. [BUL 02] Bultitude R. J. C., “Estimating frequency correlation functions from propagation measurements on fading radio channels: a critical review”, IEEE Journal on Selected Areas in Communication, vol. 20, no. 6, p. 1133–1143, August 2002. [BUR 83] Burnside W., Burgener K., “High frequency scattering by a thin lossless dielectric slab”, IEEE Transactions on Antennas and Propagation, vol. 31, no. 1, p. 104–109, January 1983. [CAS 01] Cassioli D., Win M. Z., Molisch A. F., “A statistical model for the UWB indoor channel”, IEEE Vehicular Technology Conference, VTC Spring, vol. 2, Rhodes, Greece, p. 1159–1163, May 2001. [CAS 02] Cassioli D., Win M. Z., Molisch A. F., “The ultra-wide bandwidth indoor channel: from statistical model to simulations”, IEEE Journal on Selected Areas in Communications, vol. 20, no. 6, p. 1247–1257, August 2002. [CAS 03] Cassioli D., Ciccognani W., Durantini A., UWB Channel Model Report, Report, IST Ultrawaves Project, November 2003. [CAS 04a] Cassioli D., Durantini A., “Statistical characterization of UWB indoor propagation channels based on extensive measurement campaigns”, International Symposium on Wireless Personal Multimedia Communications, vol. 1, Abano Terme, Italy, p. 236–240, September 2004. [CAS 04b] Cassioli D., Durantini A., “A time-domain propagation model of the UWB indoor channel in the FCC-compliant band 3.6-6 GHz based on PN-sequence channel measurements”, IEEE Vehicular Technology Conference, VTC Spring, vol. 1, Milan, Italy, p. 213–217, May 2004. [CAS 04c] Cassioli D., Durantini A., Ciccognani W., “The role of path loss on the selection of the operating bands of UWB systems”, IEEE International Symposium on Personal, Indoor and Mobile Radio Communications, vol. 4, Barcelona, Spain, p. 2787–2791, September 2004.

222

Ultra-Wideband Radio Propagation Channels

[CHA 03] Chaigneaud L., Effets du mobilier et des personnes sur la propagation radio indoor ` a 60 GHz, PhD Thesis, Poitiers University, France, 2003. [CHA 04] Chang W. J., Tarng J. H., Shen M. J., “Radio bandwidth on the averaged power-delay profiles of UWB indoor channels”, COST 273 Workshop, Gothenburg, Sweden, June 2004. [CHE 96] Chen S., Jeng S., “SBR image approach for radio wave propagation in tunnels with and without traffic”, IEEE Transactions on Vehicular Technology, vol. 45, no. 3, p. 570–578, August 1996. [CHE 02] Cheung D., Prettie C., A path loss comparison between the 5 GHz UNII band (802.11a) and the 2.4 GHz ISM band (802.11b), Report, Intel Corporation, January 2002. [CHO 04a] Chong C. C., Kim Y., Lee S. S., UWB Channel Model for Indoor Residential Environment, Report no. IEEE P802.15-04/452, IEEE P802.15 Working Group for Wireless Personal Area Networks (WPANs), September 2004. [CHO 04b] Chong C. C., Kim Y., Lee S. S., “UWB indoor propagation channel measurements and data analysis in various types of high-rise apartments”, IEEE Vehicular Technology Conference, VTC Fall, vol. 1, Los Angeles, CA, USA, p. 150–154, September 2004. [CHO 05] Chong C. C., Kim Y., Lee S. S., “Statistical characterization of the UWB propagation channel in various types of high-rise apartments”, IEEE Wireless Communications and Networking Conference, vol. 2, New Orleans, LA, USA, p. 944–949, March 2005. [CLA 68] Clarke R. H., “Statistical theory of mobile-radio reception”, Bell System Technical Journal, vol. 47, p. 957–1000, July 1968. [COC 05] Cocheril Y., Vauzelle R., Aveneau L., Khoudeir M., “Mod´elisation et prise en compte des surfaces rugueuses pour un simulateur de propagation d’ondes ees Nationales MicroOndes a 60 GHz en milieu indoor”, Actes des XIVieme Journ´ ` (JNM 2005), Nantes, France, May 2005. [CON 03] Conrat J. M., Pajusco P., Thiriet J. Y., “AMERICC, the France Telecom R&D wideband channel sounder from 2 to 60 GHz”, COST 273 Workshop, Barcelona, Spain, January 2003. [COS 89] COST-207, Digital land mobile radio communications, Report, European Commission, 1989. [COS 04] Cosquer R., Conception d’un sondeur de canal MIMO – Caract´erisation du canal de propagation d’un point de vue directionnel et doublement directionnel, PhD Thesis, Institut National des Sciences Appliqu´ees de Rennes, France, 2004. [COU 98] Courtney C., “Time-domain measurements of electromagnetic properties of materials”, IEEE Transactions on Microwave Theory and Techniques, vol. 46, no. 5, p. 517–522, May 1998. [CRA 98] Cramer R. J. M., Win M. Z., Scholtz R. A., “Impulse radio multipath characteristics and diversity reception”, IEEE International Conference on Communications, vol. 3, Atlanta, GA, USA, p. 1650–1654, June 1998.

Bibliography

223

[CRA 02] Cramer R. J. M., Scholtz R. A., Win M. Z., “Evaluation of an ultra-wide-band propagation channel”, IEEE Transactions on Antennas and Propagation, vol. 50, no. 5, p. 561–570, May 2002. [DAB 03] Dabin J. A., Nan N., Haimovich A. M., Niver E., Grebel H., “The effect of antenna directivity on pathloss and multipath propagation in UWB indoor wireless channels”, IEEE Conference on Ultra Wideband Systems and Technologies, Reston, VA, USA, p. 305–309, November 2003. [DEB 96] De Backer B., Borjeson H., Olyslager F., DeZutter D., “The study of wave propagation through periodic structures”, IEEE Vehicular Technology Conference, Atlanta, GA, USA, p. 165–169, April 1996. [DEN 03a] Denis B., Keignart J., “Post-processing framework for enhanced UWB channel modeling from band-limited measurements”, IEEE Conference on Ultra Wide Band Systems and Technologies, Reston, VA, USA, p. 260–264, November 2003. [DEN 03b] Denis B., Keignart J., Daniele N., “Impact of NLOS propagation upon ranging precision in UWB systems”, Proceedings of IEEE Conference on Ultra Wideband Systems and Technologies (UWBST 2003), Reston, VA, USA, p. 261–264, November 2003. [DES 84] Deschamps G., Boersma J., Lee S.-W., “Three-dimensional half-plane diffraction: exact solution and testing of uniform theories”, IEEE Transactions on Antennas and Propagation, vol. 32, no. 3, p. 264–271, March 1984. [DUR 04] Durantini A., Ciccognani W., Cassioli D., “UWB propagation measurements by PN sequence channel sounding”, IEEE International Conference on Communications, vol. 6, Paris, France, p. 3414–3418, June 2004. [ECC 06] ECC, ECC decision of 24 March 2006 on the harmonised conditions for devices using Ultra-Wideband (UWB) technology in bands below 10.6 GHz, Report no. ECC/DEC/(06)04, Electronic Communications Commitee, March 2006. [ECM 05] ECMA, High Rate Ultra Wideband PHY and MAC Standards, Report no. ECMA-368, ECMA International, December 2005. [FCC 02] FCC, First report and order, revision of Part 15 of the Commission’s rules regarding ultra-wideband transmission systems, Report no. ET Docket 98-153, FCC, April 2002. [FIS 04] Fisher R., Kohno R., Mc Laughlin M., Wellborn M., DS-UWB physical layer submission to 802.15 Task Group 3a, Report no. IEEE P802.15-04/0137r3, IEEE P802.15 Working Group for Wireless Personal Area Networks (WPANs), July 2004. [FOE 01a] Foerster J., Green E., Somayazulu S., Leeper D., “Ultra-wideband technology for short- or medium-range wireless communications”, Intel Technology Journal, Q2 2001.

224

Ultra-Wideband Radio Propagation Channels

[FOE 01b] Foerster J. R., “The effects of multipath interference on the performance of UWB systems in an indoor wireless channel”, IEEE Vehicular Technology Conference, VTC Spring, vol. 2, Rhodes, Greece, p. 1176–1180, May 2001. [FOE 03a] Foerster J., Channel Modeling Sub-comitee Report Final, Report no. IEEE P802.15- 02/490r1-SG3a, IEEE P802.15 Working Group for WPANs, February 2003. [FOE 03b] Foerster J., Li Q., UWB channel modeling contribution from Intel, Report no. IEEE 802.15-02/287, IEEE P802.15 Working Group for Wireless Personal Area Networks (WPANs), July 2003. [FOL 84] Foley J., Van Dam A., Hughes J., Computers Graphics: Principles and Practices, Addison-Wesley Publishing Companies, 1984. [FOW 90] Fowler C., Entzminger J., Corum J. O., “Assessment of ultra wideband (UWB) technology”, IEEE Aerospace and Electronic Systems Magazine, vol. 5, no. 11, p. 45–49, November 1990. [GAR 87] Gardiol F., Trait´ e d’Electricit´e, d’Electronique et d’Electrotechnique: Electromagn´etisme, Dunod, 1987. [GAU 03] Gaur S., Annamalai A., “Improving the range of ultrawideband transmission using RAKE receivers”, IEEE Vehicular Technology Conference, VTC Fall, vol. 1, Orlando, FL, USA, p. 597–601, October 2003. [GHA 02a] Ghassemzadeh S. S., Jana R., Rice C. W., Turin W., Tarokh V., “A statistical path loss model for in-home UWB channels”, IEEE Conference on Ultra Wideband Systems and Technologies, Baltimore, MD, USA, p. 59–64, May 2002. [GHA 02b] Ghassemzadeh S. S., Tarok V., The ultra-wideband indoor multipath loss model, Report no. IEEE 802.15-02/283, IEEE P802.15 Working Group for Wireless Personal Area Networks (WPANs), July 2002. [GHA 03a] Ghassemzadeh S. S., Greenstein L. J., Kavcic A., Sveinsson T., Tarokh V., “UWB indoor delay profile model for residential and commercial environments”, IEEE Vehicular Technology Conference,VTC Fall, vol. 5, Orlando, FL, USA, p. 3120–3125, October 2003. [GHA 03b] Ghassemzadeh S. S., Greenstein L. J., Kavcic A., Sveinsson T., Tarokh V., “UWB indoor path loss model for residential and commercial buildings”, IEEE Vehicular Technology Conference,VTC Fall, vol. 5, Orlando, FL, USA, p. 3115–3119, October 2003. [GHA 03c] Ghassemzadeh S. S., Tarokh V., “UWB path loss characterization in residential environments”, IEEE Radio Frequency Integrated Circuits Symposium, Philadelphia, PA, USA, p. 501–504, June 2003. [GHA 04a] Ghassemzadeh S. S., Jana R., Rice C. W., Turin W., Tarokh V., “Measurement and modeling of an ultra-wide bandwidth indoor channel”, IEEE Transactions on Communications, vol. 52, no. 10, p. 1786–1796, October 2004.

Bibliography

225

[GHA 04b] Ghavami M., Michael L., Kohno R., Ultra Wideband: Signals and Systems in Communication Engineering, Wiley, 2004. [GLO 99] Gloria B., Elaboration d’un outil de planification et d’optimisation pour le DCS 1800 en milieux confin´es, PhD Thesis, Insa de Rennes, November 1999. [GUI 96] Guillet V., Caract´erisation de la propagation multitrajets en vue de la pr´ediction de la qualit´e de transmission GSM/DCS 1800 en petites et micro-cellules urbaines, PhD Thesis, Ecole Nationale Sup´erieure des T´el´ecommunications de Paris, France, 1996. [GUI 99] Guillouard S., Conception et r´ealisation d’un sondeur de canal tr`es large bande ` a 60 GHz - Mesures de propagation ` a l’int´erieur des bˆ atiments, PhD Thesis, Institut National des Sciences Appliqu´ees de Rennes, France, 1999. [GUN 00] Gunderson S. J., Scholtz R., Chugg K., Weaver R., Lee J. Y., Corrada C., Homier E., Wilson R., Shipboard environment characterization, Appendix A: Naval total asset visibility tests on the USS Curtiss, Report, UltRaLab, 2000. [HAN 03] Haneda K., Takada J., “An application of SAGE algorithm for UWB propagation channel estimation”, IEEE Conference on Ultra Wide Band Systems and Technologies, Reston, VA, USA, p. 483–487, November 2003. [HAN 04] Haneda K., Takada J. I., Kobayashi T., “Clusterization analyses of spatio-temporal UWB radio channels in line-of-sight and non-line-of-sight indoor home environments”, Joint COST 273/284 Workshop, Gothenburg, Sweden, June 2004. [HAN 05] Haneda K., Takada J., Kobayashi T., “On the cluster properties in UWB spatio-temporal residential measurement”, COST 273 Workshop, Bologna, Italy, January 2005. [HAR 78] Harris F. J., “On the use of windows for harmonic analysis with the discrete fourier transform”, Proceedings of the IEEE, vol. 66, no. 1, p. 51–83, January 1978. [HAS 93] Hashemi H., “The indoor radio propagation channel”, Proceedings of the IEEE, vol. 81, no. 7, p. 943–968, July 1993. [HAS 94a] Hashemi H., “A study of temporal and spatial variations of the indoor radio propagation channel”, IEEE International Symposium on Personal, Indoor and Mobile Radio Communications, vol. 1, The Hague, The Netherlands, p. 127–134, September 1994. [HAS 94b] Hashemi H., McGuire M., Vlasschaert T., Tholl D., “Measurements and modeling of temporal variations of the indoor radio propagation channel”, IEEE Transactions on Vehicular Technology, vol. 43, no. 3, p. 733–737, August 1994. [HAY 01] Haykin S., Communication Systems, Wiley, New York, 2001. ¨ 74] H¨ [HOG ogbom J. A., “Aperture synthesis with a non-regular distribution of interferometer baselines”, Astronomy and Astrophysics Supplement Series, vol. 15, p. 417–426, 1974.

226

Ultra-Wideband Radio Propagation Channels

[HOF 03] Hoff H., Eggers P. C. F., Kovacs I. Z., “Directional indoor ultra wideband propagation mechanisms”, IEEE Vehicular Technology Conference, VTC Fall, vol. 1, Orlando, FL, USA, p. 188–192, October 2003. [HOV 02] Hovinen V., H¨ am¨ al¨ ainen M., P¨ atsi T., “Ultra wideband indoor radio channel models: preliminary results”, IEEE Conference on Ultra Wide Band Systems and Technologies, pp. 13-17, Baltimore, MD, USA, p. 75–79, May 2002. [HOV 03] Hovinen V., H¨ am¨ al¨ ainen M., Tesi R., Hentil¨ a L., Laine N., A proposal for a selection of indoor UWB path loss model, Report no. IEEE 802.15-02/280, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), July 2003. [HUA 96] Huang Y., Parsons D., “A time domain approach for measuring the dielectric properties and thickness of walls of a building”, Proceedings of IEE Colloquium on Propagation Aspects of Future Mobile Systems, London, UK, October 1996. [HUM 03] Humbert C., Simulation du canal de propagation indoor, PhD Thesis, Marne-la-Vall´ee University, December 2003. [IBA 00] Ibazizen A., Extension de la m´ethode FDTD aux applications ´electromagn´etiques de grande taille, PhD Thesis, Pierre and Marie Curie University, France, 2000. [IKE 91] Ikegami F., Takeuchi T., Yoshida S., “Theoretical prediction of mean field strength for urban mobile radio”, IEEE Transactions on Antennas and Propagation, vol. 39, no. 3, p. 299–302, March 1991. [ITU 04] ITU, Propagation prediction methods for the planning of ultra-wideband applications in the frequency range 1 GHz to 10 GHz (draft recommendation), Report no. 3K/TEMP/18-E, International Telecommunications Union, October 2004. [JAK 93] Jakes W. C., Microwave Mobile Communications, IEEE Press, New York, 1993. a L., “Comparison of wideband and [JAM 04] Jamsa T., Hovinen V., Hentil¨ ultra-wideband channel measurements”, COST 273, Gothenburg, Sweden, June 2004. [KAR 04a] Karedal J., Wyne S., Almers P., Tufvesson F., Molisch A. F., “Statistical analysis of the uwb channel in an industrial environment”, IEEE Vehicular Technology Conference, VTC Fall, vol. 1, Los Angeles, CA, USA, p. 81–85, September 2004. [KAR 04b] Karedal J., Wyne S., Almers P., Tufvesson F., Molisch A. F., “UWB channel measurements in an industrial environment”, IEEE Global Telecommunications Conference, vol. 6, Dallas, TX, USA, p. 3511–3516, November 2004. [KAT 00] Kattenbach R., Weitzel D., “Wideband channel sounder for time-variant indoor radio channels”, Conference on Antennas and Propagation, Davos, Switzerland, April 2000.

Bibliography

227

[KEI 02] Keignart J., Daniele N., “Subnanosecond UWB channel sounding in frequency and temporal domain”, IEEE Conference on Ultra Wide Band Systems and Technologies, Baltimore, MD, USA, p. 25–30, May 2002. [KEI 03] Keignart J., Daniele N., “Channel sounding and modelling for indoor UWB communications”, International Workshop on Ultra Wideband Systems, Oulu, Finland, June 2003. [KEI 04] Keignart J., Daniele N., UWB Channel measurements in Snow-Covered Environment, Report no. IEEE 802.15-04/449, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), August 2004. [KEL 62] Keller J., “Geometrical theory of diffraction”, Journal Optical Society of America, vol. 52, no. 2, p. 116–130, February 1962. [KIM 97] Kimpe M., LeiB H., “Computerized indoor radio channel estimation using ray tracing”, Annales des t´el´ecommunications, vol. 52, no. 5-6, p. 251–263, 1997. [KOL 33] Kolmogorov A. N., “Sulla determinazione empirica di una legge di distribuzione”, Giornale dell’ Istituto Italiano degli Attuari, vol. 4, no. 1, p. 83–91, January 1933. [KON 99] Kondylis G., De Flaviis F., Pottie G., Rahmat-Samii Y., “Indoor channel characterization for wireless communications using reduced finite difference time domain”, IEEE Vehicular Technology Conference, VTC Fall, Amsterdam, The Netherlands, p. 1402–1406, September 1999. [KOU 74] Kouyoumjian R., Pathak P., “A uniform geometrical theory of diffraction for an edge in a perfectly conducting surface”, IEEE Transactions on Antennas and Propagation, vol. 62, no. 7, p. 1448–1496, November 1974. ´cs I., Eggers P. C. F., “Short-range UWB radio propagation using [KOV 03] Kova small terminal antennas”, International Workshop on Ultra Wideband Systems, Oulu, Finland, June 2003. [KRA 93] Kralj D., Carin L., “Ultra-wideband characterization of lossy materials: short-pulse microwave measurements”, Proceedings of IEEE Microwave Theory an Techniques Symposium, Atlanta, GA, USA, June 1993. [KUN 02a] Kunisch J., Pamp J., “Measurement results and modelling aspects for the UWB radio channel”, IEEE Conference on Ultra Wide Band Systems and Technologies, Baltimore, MD, USA, p. 19–23, May 2002. [KUN 02b] Kunisch J., Pamp J., Radio channel model for indoor UWB WPAN environments, Report no. IEEE 802.15-02/281, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), June 2002. [KUN 03] Kunisch J., Pamp J., “An ultra-wideband space-variant multipath indoor radio channel model”, IEEE Conference on Ultra Wide Band Systems and Technologies, Reston, VA, USA, p. 290–294, November 2003. [LAU 94] Laurenson D. I., Indoor radio channel propagation modelling by ray tracing techniques, PhD Thesis, Edinburgh University, UK, 1994.

228

Ultra-Wideband Radio Propagation Channels

[LAU 95] Lauer A., Woff I., Bahr A., Pamp J., Kunish J., “Multi-mode FDTD simulations of indoor propagation including antenna properties”, Proceeding of the 1995 IEEE 45th Vehicular Technology Conference, Chicago, IL, USA, p. 454–458, 1995. [LEE 85] Lee W. C. Y., “Estimate of local average power of a mobile radio signal”, IEEE Transactions on Vehicular Technology, vol. 34, no. 1, p. 22–27, February 1985. [LEE 02] Lee J. Y., Scholtz R. A., “Ranging in a dense multipath environment using an UWB radio link”, IEEE Journal on Selected Areas in Communications, vol. 20, no. 9, p. 1677–1683, December 2002. [LEG 95] Legendre J.-F., Etude de mod`ele de pr´ediction de la propagation bas´es sur la th´eorie g´eom´etrique de la diffraction, PhD Thesis, INSA de Rennes, France, January 1995. [LEG 05] Legendre J.-F., Gesny O., Bayetto J.-C., Roger L., “New propagation model using fast 3D ray tracing. Application to WIFI”, European Conference on Propagation and Systems (ECPS 2005), Brest, France, March 2005. [LI 03] Li Q., Wong W. S., “Measurement and analysis of the indoor UWB channel”, IEEE Vehicular Technology Conference, VTC Fall, vol. 1, Orlando, FL, USA, p. 1–5, October 2003. [LIC 03] Licul S., Davis W. A., Stutzman W. L., “Ultra-wideband (UWB) communication link modeling and characterization”, IEEE Conference on Ultra Wideband Systems and Technologies, Reston, VA, USA, p. 310–314, November 2003. [LIN 89] Ling H., Chou R., Lee S., “Shooting and Bouncing Rays: Calculating Shaped Cavity”, IEEE Transactions on Antennas and Propagation, vol. 37, p. 194–205, January 1989. [LO 88] Lo Y., Lee S., Antenna Handbook, Theory, Applications and Design, Van Nostrand Reinhold Company., New York, 1988. [LUE 89] Luebbers R., “A Heuristic UTD Slope diffraction coefficient for rough lossy wedges”, IEEE Transactions on Antennas and Propagation, vol. 37, no. 2, p. 206–211, November 1989. [MAR 60] Marcum J., “A statistical theory of target detection by pulsed radar”, IEEE Transactions on Information Theory, vol. 6, no. 2, p. 59–267, April 1960. [MAX 55] Maxwell J. C., “On Faraday’s lines of forces”, Cambridge Philosophical Society Conference, Cambridge, UK, December 1855. [MCK 91] McKown J., Hamilton R., “Ray Tracing as a Design Tool for Radio Networks”, IEEE Network Magazine, vol. 5, no. 11, p. 27–30, November 1991. [MCK 03] McKinstry D. R., Buehrer R. M., “UWB small scale channel modeling and system performance”, IEEE Vehicular Technology Conference, VTC Fall, vol. 1, Orlando, FL, USA, p. 6–10, October 2003.

Bibliography

229

[MCN 90] McNamara D., Pistorius C., Malherbe J., Introduction to the Uniform Geometrical Theory of Diffraction, Artech House, 1990. [MOL 03] Molisch A. F., Foerster J. R., Pendergrass M., “Channel models for ultrawideband personal area networks”, IEEE Wireless Communications, vol. 10, no. 6, p. 14–21, December 2003. [MOL 04] Molisch A. F., Balakrishnan K., Chong C. C., Emami S., Fort A., Karedal J., Kunisch J., Schantz H., Schuster U., Siwiak K., IEEE 802.15.4a channel model–final report, Report no. IEEE P802.15-04/0662, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), November 2004. [MOR 03] Morche D., Helal D., “RF front-ends implementation aspects and regulation status”, The Ultra Wide Band Summit, Paris, France, December 2003. [MUQ 03a] Muqaibel A. H. andSafaai-Jazi A., “A new formulation for characterization of materials based on measured insertion transfer unction”, IEEE Transactions on Microwave Theory and Techniques, vol. 51, no. 8, p. 1946–1952, August 2003. [MUQ 03b] Muqaibel A. H., Safaai-Jazi A., Attiya A. M., Bayram A., Riad S. M., “Measurement and characterization of indoor ultra-wideband propagation”, IEEE Conference on Ultra Wideband Systems and Technologies, Reston, VA, USA, p. 295–299, November 2003. [OPS 01] Opshaug G. R., Enge P., “GPS and UWB for indoor navigation”, Institute of Navigation’s GPS Conference, Salt Lake City, UT, USA, September 2001. [OSS 03] Ossberger G., Buchegger T., Stelzer A., Diskus C., Weigel R., “A Comparison of CPW-to-CPS fed ultra wideband antennas”, Proceedings of International Workshop on UWB Systems (IWUWBS 2003), Oulu, Finland, June 2003. [PAE 02] Paetzold M., Mobile Fading Channels, Wiley, Chichester, 2002. [PAG 03] Pagani P., Pajusco P., Voinot S., “A study of the ultra-wide band indoor channel: propagation experiment and measurement results”, International Workshop on Ultra Wideband Systems, Oulu, Finland, June 2003. [PAG 04] Pagani P., Pajusco P., “Experimental assessment of the UWB channel variability in a dynamic environment”, International Symposium on Personal, Indoor and Mobile Radio Communications, vol. 4, Barcelona, Spain, p. 2973–2977, September 2004. [PAG 05] Pagani P., Caract´erisation et mod´elisation du canal de propagation radio en contexte Ultra Large Bande, PhD Thesis, Institut National des Sciences Appliqu´ees de Rennes, France, 2005. [PAG 06a] Pagani P., Pajusco P., “Characterization and modeling of temporal variations on a ultra-wideband radio link”, IEEE Transactions on Antennas and Propagation, vol. 54, no. 11-1, p. 3198–3206, November 2006.

230

Ultra-Wideband Radio Propagation Channels

[PAG 06b] Pagani P., Pajusco P., “Experimental analysis of the ultra wideband propagation channel over the 3.1 GHz–10.6 GHz frequency band”, IEEE International Symposium on Personal, Indoor and Mobile Radio Communications, Helsinki, Finland, September 2006. [PAG 06c] Pagani P., Pajusco P., “Modeling the space- and time-variant ultra-wideband propagation channel”, IEEE International Conference on Ultra Wide Band, Waltham, MA, USA, September 2006. [PAG 06d] Pagani P., Pajusco P., “Statistical modeling of the ultra wide band propagation channel through the analysis of experimental measurements”, Comptes Rendus de l’Acad´ emie des Sciences, Physique, vol. 7, p. 762–773, September 2006. [PAJ 03] Pajusco P., Pagani P., “Extension of SIMO wideband channel sounder for UWB propagation experiment”, IEEE Conference on Ultra Wideband Systems and Technologies, Reston, VA, USA, p. 250–254, November 2003. [PAJ 07] Pajusco P., Pagani P., “Frequency dependence of the UWB indoor propagation channel”, European Conference on Antennas and Propagation, Edinburgh, UK, p. 1–7, November 2007. [PAR 00] Parsons J. D., The Mobile Radio Propagation Channel, Wiley, Chichester, 2000. [PEN 02] Pendergrass M., Beeler W. C., Empirically based statistical Ultra-Wideband (UWB) channel model, Report no. IEEE 802.15-02/240, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), June 2002. [PET 93] Petit R., Ondes electromagn´etiques en radio´ electricit´e et en optique, Masson, 1993. [PEZ 03] Pezzin M., Keignart J., Daniele N., De Rivaz S., Denis B., Morche D., Rouzet P., Catenoz R., Rinaldi N., “Ultra Wideband: the radio link of the future?”, Annales des T´el´ecommunications, vol. 58, no. 3-4, p. 464–506, March 2003. [PLO 00] Plouhinec E., Etude et Extension de mod`eles de Pr´ediction de la Propagation: Elaboration d’un Serveur Expert Multi-Mod`eles, PhD Thesis, INSA de Rennes, France, December 2000. [PLO 03] Plouhinec E., Uguen B., Tchoffo Talom F., “A parametric study of GO transmission applied to an ultra wide band signal”, Proceedings of International Conference on Electromagnetics in Advanced Applications (ICEAA’03), Turin, Italy, p. 57–60, September 2003. [POR 03a] Porcino D., “UWB regulations and coexistence: from the FCC first report and order to the path to approval in Europe”, International Workshop on Ultra Wideband Systems, Oulu, Finland, June 2003. [POR 03b] Porcino D., Hirt W., “Ultra-wideband radio technology: potential and challenges ahead”, IEEE Communications Magazine, vol. 41, no. 7, p. 66–74, July 2003. [PRO 83] Proakis J. G., Digital Communications, McGraw-Hill, New York, 1983.

Bibliography

231

[QIU 02] Qiu R., “A study of the ultra-wideband wireless propagation channel and optimum UWB receiver design”, IEEE Journal on Selected Areas in Communications, vol. 20, no. 9, p. 1628–1637, December 2002. [RIZ 97] Rizk K., Wagen J. F., Gardiol F., “Two-dimensional ray-tracing modelling for propagation prediction in microcellular environnments”, IEEE Transactions on Vehicular Technology, vol. 46, no. 2, p. 508–518, May 1997. [ROU 95] Rousseau P., Pathak P., “Time-domain uniform geometrical theory of diffraction for a curved wedge”, IEEE Transactions on Antennas and Propagation, vol. 43, no. 12, p. 1375–1382, December 1995. `re J. F., Douchin N., Combes P., “Improvement of the UTD [ROU 96] Rouvie formulation for diffraction of an electromagnetic wave by a dielectric wedge”, Electronics Letters, vol. 33, no. 5, February 1996. `re J. F., Douchin N., Combes P., “Diffraction by lossy dielectric [ROU 99] Rouvie wedge using both heuristic UTD formulations and FDTD”, IEEE Transactions on Antennas and Propagation, vol. 47, no. 11, p. 1702–1708, November 1999. [SAC 02] Sachs J., Thom¨ a R., Schultheiss U., Zetik R., Dvoracek J., Wolf M., “Real-time ultra-wideband channel sounder”, General Assembly of the Union of Radio Science, Maastricht, The Netherlands, August 2002. [SAG 03] Sagnard F., Sabouroux P., Tchoffo Talom F., El Zein G., “Reflection and transmission of pulses at oblique incidence from stratified dispersive media”, 17` eme Colloque International Optique Hertzienne et Di´electriques, Calais, France, September 2003. [SAL 87] Saleh A. A. M., Valenzuela R. A., “A statistical model for indoor multipath propagation”, IEEE Journal on Selected Areas in Communications, vol. 5, no. 2, p. 128–137, February 1987. [SAN 96] Sanchez M., DeHaro L., Pino A., “Exhaustive ray tracing algorithm for microcellular propagation prediction models”, Electronics Letters, vol. 32, no. 7, p. 624–625, March 1996. [SAR 03] Sarkar T., Ji Z., Kim K., Medouri A., Salazar-Palma M., “A Survey of Various Propagation Models for Mobile Communication”, IEEE Antennas and Propagation Magazine, vol. 45, no. 3, p. 51–82, June 2003. [SAT 95] Sato K., Kozima H., Masuzawa H., Manabe T., Ihara T., Kasashima Y., Yamaki K., “Measurements of reflection characteristics and refractive indices of interrior construction materials in millimeter-wave bands”, Proceedings of 45th IEEE Vehicular Technology Conference, New York, NY, USA, p. 449–453, 1995. [SCH 86] Schrank H., “A centenial of electromagnetics”, IEEE Antennas and Propagation Society Newsletter, vol. 28, no. 6, p. 35–38, December 1986. [SCH 93] Scholtz R. A., “Multiple access with time-hopping impulse modulation”, IEEE Military Communications Conference, vol. 2, Bedford, MA, USA, p. 447–450, October 1993. [SCH 97a] Scholtz R. A., Win M. Z., “Impulse radio”, Glisic S., Lepp¨ anen P. A., Eds., Wireless Communications: TDMA vs. CDMA, Kluwer, Norwell, 1997.

232

Ultra-Wideband Radio Propagation Channels

[SCH 97b] Schuster J., Luebbers R., “Comparison of GTD and FDTD predictions for UHF radio wave propagation in a simple outdoor urban environment”, IEEE Antennas and Propagation Society International Symposium, Montreal, Canada, p. 2022–2025, July 1997. [SCH 03a] Schantz H. G., “Introduction to ultra wideband antennas”, IEEE Conference on Ultra Wide Band Systems and Technologies, Reston, VA, USA, p. 1–9, November 2003. [SCH 03b] Schantz H., “A brief history of UWB antennas”, Proceedings of IEEE Conference on Ultra Wideband Systems and Technologies (UWBST 2003), Reston, VA, USA, November 2003. [SCH 03c] Schantz H., “Introduction to ultra-wideband antennas”, Proceedings of IEEE Conference on Ultra Wideband Systems and Technologies (UWBST 2003), Reston, VA, USA, November 2003. [SCH 04] Schuster U., Indoor UWB Channel Measurements from 2 GHz to 8 GHz, Report no. IEEE 802.15-04/447, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), September 2004. [SHA 49] Shannon C. E., “Communication in the presence of noise”, Proceedings of the Institute of Radio Engineers, vol. 37, no. 1, p. 10–21, January 1949. [SIB 04] Sibille A., Roblin C., Bories S., Lepage A. C., Begaud X., “Conception et caract´erisation d’antennes ULB pour communications multim´edia haut d´ebit”, Revue de l’Electricit´e et de l’Electronique, vol. 4, p. 73–80, April 2004. [SIW 02] Siwiak K., UWB propagation phenomena, Report no. IEEE 802.15-02/301, IEEE 802.15 Working Group for Wireless Personal Area Networks (WPANs), July 2002. [SPE 97] Spencer Q., Rice M., Jeffs B., Jensen M., “A statistical model for angle of arrival in indoor multipath propagation”, IEEE Vehicular Technology Conference, VTC Spring, vol. 3, Phoenix, AZ, USA, p. 1415–1419, May 1997. [STA 98] Stanislawiak M., Elaboration d’un mod`ele 3D de pr´ediction bas´e sur la technique de lancer de rayons, PhD Thesis, Lille University, France, 1998. [TAK 01] Takeuchi T., Tamura M., “A ultra-wide band channel sounder for mobile communication systems”, IEEE International Symposium on Personal, Indoor and Mobile Radio Communications, vol. 2, San Diego, CA, USA, p. 111–115, September 2001. [TAM 95] Tam W., Tran V., “Propagation modeling for indoor wireless communication”, Journal of Electronics & Communication Engineering, p. 221–228, 1995. [TAN 95] Tan S., Tan H., “Improved three-dimension ray tracing technique for microcellular propagation”, Electronics Letters, vol. 31, no. 17, p. 1503–1505, August 1995. [TAY 95] Taylor J. D., Introduction to Ultra-Wideband Radar Systems, CRC Press, Boca Raton, 1995.

Bibliography

233

[TCH 03] Tchoffo Talom F., Uguen B., Chassay G., “Une m´ethode d’acc´el´eration de la d´etermination de rayons pour la caract´erisation de canaux ees Nationales MicroOndes (JNM 2003), Lille, radio”, Actes des XIIIi`eme Journ´ France, May 2003. [TCH 04] Tchoffo Talom F., Uguen B., Plouhinec E., Chassay G., “A site specific ultra wideband channel modeling”, IEEE International Workshop on Ultra Wide Band Systems (IWUWBS2004) Joint with Conference on Ultra Wide Band Systems and Technologies (UWBST2004), Kyoto, Japan, May 2004. [TCH 05a] Tchoffo Talom F., Mod´elisation d´eterministe du canal de propagation indoor dans un contexte UWB, PhD Thesis, Institut National des Sciences Appliqu´ees de Rennes, France, 2005. ´ J.-B., Uguen B., Plouhinec E., [TCH 05b] Tchoffo Talom F., Dore Chassay G., “UWB in-home modelling”, Proceedings of European Conference on Propagation and Systems (ECPS 2005), Brest, France, March 2005. [TCH 06] Tchoffo Talom F., Uguen B., Aubert L.-M., “Antennas link synthesis using near field chamber measurements”, Proceedings of European Conference on Antenna and Propagation (EUCAP), Nice, France, November 2006. ´ M., Hong A., Guibe ´ G., Legrand F., “Major characteristics [TER 03] Terre of UWB indoor transmission for simulation”, IEEE Vehicular Technology Conference, VTC Spring, vol. 1, Jeju, Korea, p. 19–23, April 2003. [TSU 04] Tsuchiya H., Haneda K., Takada J., “Double-directional channel sounding with ultra wideband signal in an indoor office environment”, COST 273 Workshop, Duisburg, Germany, September 2004. [UGU 02] Uguen B., Plouhinec E., Lostanlen Y., Chassay G., “A deterministic ultra wideband channel modeling”, Proceedings of IEEE Conference on Ultra Wide Band Systems and Technology (UWBST 2002), Baltimore, MD, USA, p. 1–5, May 2002. [UGU 04] Uguen B., Tchoffo Talom F., Chassay G., “UWB radio link modeling for multipath environment”, European Conference on Electromagnetics, Magdeburg, Germany, July 2004. [UGU 05] Uguen B., Tchoffo Talom F., “Implementation of UWB antenna characteristics in 3D ray tracing”, Proceedings of International Conference on Electromagnetics in Advanced Applications (ICEAA’05), Turin, Italy, September 2005. [VEN 05] Venkatesh S., Bharadwaj V., Buehrer R. M., “A new spatial model for impulse-based ultra-wideband channels”, IEEE Vehicular Technology Conference, VTC Fall, vol. 4, Dallas, TX, USA, September 2005. [VER 90] Veruttipong T., “Time domain version of the uniform GTD”, IEEE Transactions on Antennas and Propagation, vol. 38, no. 11, p. 1757–1764, November 1990.

234

Ultra-Wideband Radio Propagation Channels

[VIL 99] Villanese F., Scanlon W., Evans N., Gambi E., “Hybrid image/ray-shooting UHF radio propagation predictor for populated indoor environments”, Electronics Letters, vol. 35, no. 21, p. 1804–1805, October 1999. [WEL 03] Welborn M., Shvodian W., “Ultra-wideband technology for wireless personal area networks – the IEEE 802.15.3/3a standards”, IEEE Conference on Ultra Wideband Systems and Technologies, Reston, VA, USA, November 2003. [WIE 03] Wiesbeck W., Younis M., Baldauf M., Advanced radio communication, Report, Institut f¨ ur H¨ ochstfrequenztechnik und Elektronik, Karlsruhe University, Germany, 2003. [WIN 97a] Win M. Z., Ramirez-Mireles F., Scholtz R. A., Barnes M. A., “Ultra-wide bandwidth (UWB) signal propagation for outdoor wireless communications”, IEEE Vehicular Technology Conference, vol. 1, Phoenix, AZ, USA, p. 251–255, May 1997. [WIN 97b] Win M. Z., Scholtz R. A., Barnes M. A., “Ultra-wide bandwidth signal propagation for indoor wireless communications”, IEEE International Conference on Communications, Montreal, Canada, p. 56–60, June 1997. [WIT 99] Withington P., Reinhardt R., Stanley R., “Preliminary results of an ultra-wideband (impulse) scanning receiver”, IEEE Military Communications Conference, vol. 2, Atlantic City, NJ, USA, p. 1186–1190, October 1999. [YAN 98] Yang C., Wu B., Ko C., “A ray-tracing method for modeling indoor wave propagation and penetration”, IEEE Transactions on Antennas and Propagation, vol. 46, no. 6, p. 907–919, June 1998. [YAN 99] Yang C., Wu B., “Simulations and measurements for indoor wave propagation through periodic structures”, IEEE International Symposium on Antennas and Propagation, Orlando, FL, USA, p. 384–387, July 1999. [YAN 02] Yano S. M., “Investigating the ultra-wideband indoor wireless channel”, IEEE Vehicular Technology Conference, VTC Spring, vol. 3, Birmingham, AL, USA, p. 1200–1204, May 2002. [YAN 04] Yang L., Giannakis G. B., “Ultra-wideband communications: an idea whose time has come”, IEEE Signal Processing Magazine, vol. 21, no. 6, p. 26–54, November 2004. [YAO 97] Yao Y., “A time-domain ray model for predicting indoor wideband radio channel propagation characteristics”, Proceeding of IEEE 6th International Conference on Universal Personal Communications Record, vol. 2, San Diego, CA, USA, p. 848–852, October 1997. [YAO 03a] Yao R., Gao G., Chen Z., Zhu W., “UWB multipath channel model based on time-domain UTD technique”, IEEE Global Telecommunications Conference, San Francisco, CA, USA, p. 1205–1210, December 2003. [YAO 03b] Yao R., Zhu W., Chen Z., “An efficient time-domain ray model for UWB indoor multipath propagation channel”, IEEE Global Telecommunications Conference, San Francisco, CA, USA, p. 1293–1297, December 2003.

Bibliography

235

[YIN 00] Ying W., Safavi-Naeini S., Chaudhuri S., “A hybrid technique based on combining ray tracing and FDTD methods for site-specific modeling of indoor radio wave propagation”, IEEE Transactions on Antennas and Propagation, vol. 48, no. 5, p. 743–745, May 2000. [ZHA 00] Zhang W., “Fast two-dimensional diffraction modeling for site-specific propagation prediction in urban microcellular environments”, IEEE Transactions on Vehicular Technology, vol. 49, no. 2, p. 428–436, March 2000.

This page intentionally left blank

Index

A Antenna diversity, 102 effective area, 44, 134 isotropic, 111 polarization, 107 radiation efficiency, 107 return loss, 107 Arrival rate cluster, 61, 145 ray, 146 rays, 61 Average fade duration, 64 B BER, 24 Bluetooth, 26, 27, 29, 30 BPSK, 39, 40 C CDMA, 38, 40 Channel characteristic parameters, 58, 134, 137 definition, 43 deterministic, 52 impulse response, 181 linear random, 54 matrix, 108 propagation, 25 representation, 51, 177 sounding, 67

transfer function, 213 US, 56 variations, 47, 148, 150 WSS, 55 WSSUS, 57 Channel capacity, 24 Channel equalization, 49 Channel modeling statistical, 133 Chirp sounder, 72 Coherence bandwidth, 49, 59 Correlation bandwidth, 49 Correlation sounder, 75 sliding correlation, 76 D DAA, 33 Delay interval, 60 Delay window, 60 Delay-Doppler spread function, 54 Deterministic model, 99 Diffraction, 47 Diffusion, 47 DoA, 104 DoD, 104 Doppler effect, 50 shift, 50, 69, 156 spectrum, 64, 173 spread, 64, 156, 173 DS-UWB, 35, 39, 40, 42

238

Ultra-Wideband Radio Propagation Channels

Duty cycle, 23

Kolmogorov-Smirnov test, 64

E ESD (Energy spectral density), 110 Exponential decay constants, 61, 141

L Laplace distribution, 170, 173, 185 Level crossing rate, 64 Log-normal distribution, 64, 150, 185 LOS, 105

F Fading fast, 48, 63, 148, 153, 172 flat, 48 slow, 48, 152, 172 Far field, 45 FCC, 22, 25, 31, 33, 34, 40, 111 FDTD, 100 Fourier transform, 103, 178, 213 Fraunhofer distance, 45 Free space propagation, 44 Frequency correlation function, 59 Frequency domain function, 53 Fresnel law, 46 Friis formula, 45, 134 G General theory diffraction, 200 Geometric optic, 189, 200 field expression, 191 field locality, 190 GO, 101 GPS, 31, 32 GSM, 30 H Hermitian symmetry, 177, 213, 215 Hilbert transform, 178 Huygens’ principle, 47 I Impulse radio, 35, 38–40 Impulse response, 51, 103, 137, 163, 166 time varying, 53 Intersymbol interference, 50, 59 Inversion sounding technique, 78 ISB, 202 K Kolmogorov-Smirnov, 186

M M-BOK, 39 m-sequence, 75 Maxwell equation, 189, 204 MB-OFDM, 35, 40–42 Mean delay, 59 Measurement campaigns, 85 examples, 91 overview, 85 Model statistical, 157 Cassioli-Win-Molisch, 160 dynamic, 169 frequency domain, 161 IEEE 802.15.3a, 158 IEEE 802.15.4a, 159 principles, 162 MoM, 100 N Nakagami distribution, 64, 150, 159, 161, 183 NLOS, 105 Normal distribution, 184, 185 O OOK, 39 P PAM, 38, 39 Path loss, 62, 134, 162 exponent distance dependent, 48, 63, 136 frequency dependent, 63, 134 Power decay constants, 144 Power delay profile, 57, 58, 137 Power spectral density, 25, 33, 37, 177 PPM, 35, 38, 39 Processing gain, 25

Index Propagation free space, 44, 134 model, 99 multipath, 45, 48 phenomena, 45 PSD (Power spectral density), 111 Pulse sounder, 73 Q QPSK, 40 R Radio channel, 26 RAKE reception, 49 Ray launching, 209, 211 Ray tracing, 209, 211 Rayleigh distribution, 64, 150, 155, 161, 173, 181, 183, 184 Rays launching, 101 Rays tracing, 101 Reflection, 46 Rice distribution, 64, 150, 155, 182, 183 RIR, 105 RMS delay spread, 59, 137 RSB, 202 RUN method, 58 S S-parameters, 71 Saleh and Valenzuela model, 61 Scattering function, 57, 64, 156, 173 Selectivity frequency, 48, 58 spatial, 48 Shadowing, 48 SHF, 30 SISO, 104 Snell-Descartes law, 46 Sounding analyzed bandwidth, 68 CIR dynamic, 69 CIR length, 69 maximum Doppler shift, 69

239

measurement techniques, 70 frequency domain, 71 multiple-band time domain, 78 time domain, 73 time resolution, 68 Standing wave ratio, 92 T Time hopping, 23 Transfer function, 125 time varying, 54 Transmission, 47 U UHF, 30 UMTS, 23, 30, 40 Uncorrelated scattering, 56 Uniform theory of diffraction, 200 UNII, 30, 34, 39 UTD, 101 UWB applications, 27, 29, 30 characteristics, 24 definition, 21, 22 history, 23 regulation, 30 V Variations spatial, 51, 150, 169 temporal, 51, 150, 172 Vector network analyzer, 71 W Waveguide effect, 47, 137 Weibull distribution, 64, 184 Wide sense stationary, 55 WiFi, 26, 27, 29, 30, 39 WLAN, 27 WPAN, 27 Z Zero padding, 215 Zigbee, 26, 29