Schaum's Outline of Theory and Problems of Electric Circuits

Theory and Problems of ELECTRIC CIRCUITS Fourth Edition MAHMOOD NAHVI, Ph.D. Professor of Electrical Engineering Calif...

Author: Mahmood Nahvi | Joseph Edminister

3051 downloads 4686 Views 6MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!

Report copyright / DMCA form

DOWNLOAD PDF

Theory and Problems of

ELECTRIC CIRCUITS Fourth Edition MAHMOOD NAHVI, Ph.D. Professor of Electrical Engineering California Polytechnic State University

JOSEPH A. EDMINISTER Professor Emeritus of Electrical Engineering The University of Akron

Schaum’s Outline Series McGRAW-HILL New York Chicago San Francisco Lisbon London Madrid Mexico City Milan New Dehli San Juan Seoul Singapore Sydney Toronto

Copyright © 2003, 1997, 1986, 1965] by The McGraw-Hill Companies, Inc. All rights reserved. Manufactured in the United States of America. Except as permitted under the United States Copyright Act of 1976, no part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of the publisher. 0-07-142582-9 The material in this eBook also appears in the print version of this title: 0-07-139307-2.

All trademarks are trademarks of their respective owners. Rather than put a trademark symbol after every occurrence of a trademarked name, we use names in an editorial fashion only, and to the benefit of the trademark owner, with no intention of infringement of the trademark. Where such designations appear in this book, they have been printed with initial caps. McGraw-Hill eBooks are available at special quantity discounts to use as premiums and sales promotions, or for use in corporate training programs. For more information, please contact George Hoare, Special Sales, at [email protected] or (212) 904-4069.

TERMS OF USE This is a copyrighted work and The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and its licensors reserve all rights in and to the work. Use of this work is subject to these terms. Except as permitted under the Copyright Act of 1976 and the right to store and retrieve one copy of the work, you may not decompile, disassemble, reverse engineer, reproduce, modify, create derivative works based upon, transmit, distribute, disseminate, sell, publish or sublicense the work or any part of it without McGraw-Hill’s prior consent. You may use the work for your own noncommercial and personal use; any other use of the work is strictly prohibited. Your right to use the work may be terminated if you fail to comply with these terms. THE WORK IS PROVIDED “AS IS”. McGRAW-HILL AND ITS LICENSORS MAKE NO GUARANTEES OR WARRANTIES AS TO THE ACCURACY, ADEQUACY OR COMPLETENESS OF OR RESULTS TO BE OBTAINED FROM USING THE WORK, INCLUDING ANY INFORMATION THAT CAN BE ACCESSED THROUGH THE WORK VIA HYPERLINK OR OTHERWISE, AND EXPRESSLY DISCLAIM ANY WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. McGraw-Hill and its licensors do not warrant or guarantee that the functions contained in the work will meet your requirements or that its operation will be uninterrupted or error free. Neither McGraw-Hill nor its licensors shall be liable to you or anyone else for any inaccuracy, error or omission, regardless of cause, in the work or for any damages resulting therefrom. McGraw-Hill has no responsibility for the content of any information accessed through the work. Under no circumstances shall McGraw-Hill and/or its licensors be liable for any indirect, incidental, special, punitive, consequential or similar damages that result from the use of or inability to use the work, even if any of them has been advised of the possibility of such damages. This limitation of liability shall apply to any claim or cause whatsoever whether such claim or cause arises in contract, tort or otherwise. DOI: 10.1036/0071425829

This book is designed for use as a textbook for a ﬁrst course in circuit analysis or as a supplement to standard texts and can be used by electrical engineering students as well as other engineereing and technology students. Emphasis is placed on the basic laws, theorems, and problem-solving techniques which are common to most courses. The subject matter is divided into 17 chapters covering duly-recognized areas of theory and study. The chapters begin with statements of pertinent deﬁnitions, principles, and theorems together with illustrative examples. This is followed by sets of solved and supplementary problems. The problems cover a range of levels of diﬃculty. Some problems focus on ﬁne points, which helps the student to better apply the basic principles correctly and conﬁdently. The supplementary problems are generally more numerous and give the reader an opportunity to practice problem-solving skills. Answers are provided with each supplementary problem. The book begins with fundamental deﬁnitions, circuit elements including dependent sources, circuit laws and theorems, and analysis techniques such as node voltage and mesh current methods. These theorems and methods are initially applied to DC-resistive circuits and then extended to RLC circuits by the use of impedance and complex frequency. Chapter 5 on ampliﬁers and op amp circuits is new. The op amp examples and problems are selected carefully to illustrate simple but practical cases which are of interest and importance in the student’s future courses. The subject of waveforms and signals is also treated in a new chapter to increase the student’s awareness of commonly used signal models. Circuit behavior such as the steady state and transient response to steps, pulses, impulses, and exponential inputs is discussed for ﬁrst-order circuits in Chapter 7 and then extended to circuits of higher order in Chapter 8, where the concept of complex frequency is introduced. Phasor analysis, sinuosidal steady state, power, power factor, and polyphase circuits are thoroughly covered. Network functions, frequency response, ﬁlters, series and parallel resonance, two-port networks, mutual inductance, and transformers are covered in detail. Application of Spice and PSpice in circuit analysis is introduced in Chapter 15. Circuit equations are solved using classical diﬀerential equations and the Laplace transform, which permits a convenient comparison. Fourier series and Fourier transforms and their use in circuit analysis are covered in Chapter 17. Finally, two appendixes provide a useful summary of the complex number system, and matrices and determinants. This book is dedicated to our students from whom we have learned to teach well. To a large degree it is they who have made possible our satisfying and rewarding teaching careers. And ﬁnally, we wish to thank our wives, Zahra Nahvi and Nina Edminister for their continuing support, and for whom all these eﬀorts were happily made. MAHMOOD NAHVI JOSEPH A. EDMINISTER

This page intentionally left blank.

For more information about this title, click here.

CHAPTER 1

CHAPTER 2

CHAPTER 3

Introduction

1

1.1 1.2 1.3 1.4 1.5 1.6

1 1 2 3 4 4

Circuit Concepts

7

2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8

7 8 9 10 11 12 12 13

Passive and Active Elements Sign Conventions Voltage-Current Relations Resistance Inductance Capacitance Circuit Diagrams Nonlinear Resistors

Circuit Laws 3.1 3.2 3.3 3.4 3.5 3.6 3.7

CHAPTER 4

Electrical Quantities and SI Units Force, Work, and Power Electric Charge and Current Electric Potential Energy and Electrical Power Constant and Variable Functions

Introduction Kirchhoff’s Voltage Law Kirchhoff’s Current Law Circuit Elements in Series Circuit Elements in Parallel Voltage Division Current Division

Analysis Methods 4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9

The Branch Current Method The Mesh Current Method Matrices and Determinants The Node Voltage Method Input and Output Resistance Transfer Resistance Network Reduction Superposition The´venin’s and Norton’s Theorems

Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

24 24 24 25 25 26 28 28

37 37 38 38 40 41 42 42 44 45

Contents

vi 4.10 Maximum Power Transfer Theorem

CHAPTER 5

Amplifiers and Operational Amplifier Circuits 5.1 Ampliﬁer Model 5.2 Feedback in Ampliﬁer Circuits 5.3 Operational Ampliﬁers 5.4 Analysis of Circuits Containing Ideal Op Amps 5.5 Inverting Circuit 5.6 Summing Circuit 5.7 Noninverting Circuit 5.8 Voltage Follower 5.9 Differental and Difference Ampliﬁers 5.10 Circuits Containing Several Op Amps 5.11 Integrator and Differentiator Circuits 5.12 Analog Computers 5.13 Low-Pass Filter 5.14 Comparator

CHAPTER 6

Waveforms and Signals 6.1 Introduction 6.2 Periodic Functions 6.3 Sinusoidal Functions 6.4 Time Shift and Phase Shift 6.5 Combinations of Periodic Functions 6.6 The Average and Effective (RMS) Values 6.7 Nonperiodic Functions 6.8 The Unit Step Function 6.9 The Unit Impulse Function 6.10 The Exponential Function 6.11 Damped Sinusoids 6.12 Random Signals

CHAPTER 7

First-Order Circuits 7.1 Introduction 7.2 Capacitor Discharge in a Resistor 7.3 Establishing a DC Voltage Across a Capacitor 7.4 The Source-Free RL Circuit 7.5 Establishing a DC Current in an Inductor 7.6 The Exponential Function Revisited 7.7 Complex First-Order RL and RC Circuits 7.8 DC Steady State in Inductors and Capacitors 7.9 Transitions at Switching Time 7.10 Response of First-Order Circuits to a Pulse 7.11 Impulse Response of RC and RL Circuits 7.12 Summary of Step and Impulse Responses in RC and RL Circuits 7.13 Response of RC and RL Circuits to Sudden Exponential Excitations 7.14 Response of RC and RL Circuits to Sudden Sinusoidal Excitations 7.15 Summary of Forced Response in First-Order Circuits 7.16 First-Order Active Circuits

CHAPTER 8

Higher-Order Circuits and Complex Frequency 8.1 Introduction

47

64 64 65 66 70 71 71 72 74 75 76 77 80 81 82

101 101 101 103 103 106 107 108 109 110 112 114 115

127 127 127 129 130 132 132 134 136 136 139 140 141 141 143 143 143

161 161

Contents

vii 8.2 Series RLC Circuit 8.3 Parallel RLC Circuit 8.4 Two-Mesh Circuit 8.5 Complex Frequency 8.6 Generalized Impedance ðR; L; CÞ in s-Domain 8.7 Network Function and Pole-Zero Plots 8.8 The Forced Response 8.9 The Natural Response 8.10 Magnitude and Frequency Scaling 8.11 Higher-Order Active Circuits

CHAPTER 9

Sinusoidal Steady-State Circuit Analysis 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

CHAPTER 10

Introduction Element Responses Phasors Impedance and Admittance Voltage and Current Division in the Frequency Domain The Mesh Current Method The Node Voltage Method The´venin’s and Norton’s Theorems Superposition of AC Sources

AC Power 10.1 Power in the Time Domain 10.2 Power in Sinusoudal Steady State 10.3 Average or Real Power 10.4 Reactive Power 10.5 Summary of AC Power in R, L, and C 10.6 Exchange of Energy Between an Inductor and a Capacitor 10.7 Complex Power, Apparent Power, and Power Triangle 10.8 Parallel-Connected Networks 10.9 Power Factor Improvement 10.10 Maximum Power Transfer 10.11 Superposition of Average Powers

CHAPTER 11

Polyphase Circuits 11.1 Introduction 11.2 Two-Phase Systems 11.3 Three-Phase Systems 11.4 Wye and Delta Systems 11.5 Phasor Voltages 11.6 Balanced Delta-Connected Load 11.7 Balanced Four-Wire, Wye-Connected Load 11.8 Equivalent Y and -Connections 11.9 Single-Line Equivalent Circuit for Balanced Three-Phase Loads 11.10 Unbalanced Delta-Connected Load 11.11 Unbalanced Wye-Connected Load 11.12 Three-Phase Power 11.13 Power Measurement and the Two-Wattmeter Method

CHAPTER 12

Frequency Response, Filters, and Resonance 12.1 Frequency Response

161 164 167 168 169 170 172 173 174 175

191 191 191 194 196 198 198 201 201 202

219 219 220 221 223 223 224 226 230 231 233 234

248 248 248 249 251 251 252 253 254 255 255 256 258 259

273 273

Contents

viii 12.2 High-Pass and Low-Pass Networks 12.3 Half-Power Frequencies 12.4 Generalized Two-Port, Two-Element Networks 12.5 The Frequency Response and Network Functions 12.6 Frequency Response from Pole-Zero Location 12.7 Ideal and Practical Filters 12.8 Passive and Active Filters 12.9 Bandpass Filters and Resonance 12.10 Natural Frequency and Damping Ratio 12.11 RLC Series Circuit; Series Resonance 12.12 Quality Factor 12.13 RLC Parallel Circuit; Parallel Resonance 12.14 Practical LC Parallel Circuit 12.15 Series-Parallel Conversions 12.16 Locus Diagrams 12.17 Scaling the Frequency Response of Filters

CHAPTER 13

Two-port Networks 13.1 Terminals and Ports 13.2 Z-Parameters 13.3 T-Equivalent of Reciprocal Networks 13.4 Y-Parameters 13.5 Pi-Equivalent of Reciprocal Networks 13.6 Application of Terminal Characteristics 13.7 Conversion Between Z- and Y-Parameters 13.8 h-Parameters 13.9 g-Parameters 13.10 Transmission Parameters 13.11 Interconnecting Two-Port Networks 13.12 Choice of Parameter Type 13.13 Summary of Terminal Parameters and Conversion

CHAPTER 14

Mutual Inductance and Transformers 14.1 Mutual Inductance 14.2 Coupling Coefﬁcient 14.3 Analysis of Coupled Coils 14.4 Dot Rule 14.5 Energy in a Pair of Coupled Coils 14.6 Conductively Coupled Equivalent Circuits 14.7 Linear Transformer 14.8 Ideal Transformer 14.9 Autotransformer 14.10 Reﬂected Impedance

CHAPTER 15

Circuit Analysis Using Spice and Pspice 15.1 15.2 15.3 15.4 15.5 15.6 15.7

Spice and PSpice Circuit Description Dissecting a Spice Source File Data Statements and DC Analysis Control and Output Statements in DC Analysis The´venin Equivalent Op Amp Circuits

274 278 278 279 280 280 282 283 284 284 286 287 288 289 290 292

310 310 310 312 312 314 314 315 316 317 317 318 320 320

334 334 335 336 338 338 339 340 342 343 344

362 362 362 363 364 367 370 370

Contents

ix 15.8 AC Steady State and Frequency Response 15.9 Mutual Inductance and Transformers 15.10 Modeling Devices with Varying Parameters 15.11 Time Response and Transient Analysis 15.12 Specifying Other Types of Sources 15.13 Summary

CHAPTER 16

The Laplace Transform Method 16.1 16.2 16.3 16.4 16.5 16.6 16.7 16.8

CHAPTER 17

Introduction The Laplace Transform Selected Laplace Transforms Convergence of the Integral Initial-Value and Final-Value Theorems Partial-Fractions Expansions Circuits in the s-Domain The Network Function and Laplace Transforms

Fourier Method of Waveform Analysis 17.1 Introduction 17.2 Trigonometric Fourier Series 17.3 Exponential Fourier Series 17.4 Waveform Symmetry 17.5 Line Spectrum 17.6 Waveform Synthesis 17.7 Effective Values and Power 17.8 Applications in Circuit Analysis 17.9 Fourier Transform of Nonperiodic Waveforms 17.10 Properties of the Fourier Transform 17.11 Continuous Spectrum

APPENDIX A

Complex Number System A1 A2 A3 A4 A5 A6 A7 A8

APPENDIX B

Matrices and Determinants B1 B2 B3 B4 B5

INDEX

Complex Numbers Complex Plane Vector Operator j Other Representations of Complex Numbers Sum and Difference of Complex Numbers Multiplication of Complex Numbers Division of Complex Numbers Conjugate of a Complex Number

Simultenaneous Equations and the Characteristic Matrix Type of Matrices Matrix Arithmetic Determinant of a Square Matrix Eigenvalues of a Square Matrix

373 375 375 378 379 382

398 398 398 399 401 401 402 404 405

420 420 421 422 423 425 426 427 428 430 432 432

451 451 451 452 452 452 452 453 453

455 455 455 456 458 460

461

This page intentionally left blank.

Introduction 1.1

ELECTRICAL QUANTITIES AND SI UNITS

The International System of Units (SI) will be used throughout this book. Four basic quantities and their SI units are listed in Table 1-1. The other three basic quantities and corresponding SI units, not shown in the table, are temperature in degrees kelvin (K), amount of substance in moles (mol), and luminous intensity in candelas (cd). All other units may be derived from the seven basic units. The electrical quantities and their symbols commonly used in electrical circuit analysis are listed in Table 1-2. Two supplementary quantities are plane angle (also called phase angle in electric circuit analysis) and solid angle. Their corresponding SI units are the radian (rad) and steradian (sr). Degrees are almost universally used for the phase angles in sinusoidal functions, for instance, sinð!t þ 308Þ. Since !t is in radians, this is a case of mixed units. The decimal multiples or submultiples of SI units should be used whenever possible. The symbols given in Table 1-3 are preﬁxed to the unit symbols of Tables 1-1 and 1-2. For example, mV is used for millivolt, 103 V, and MW for megawatt, 106 W.

1.2

FORCE, WORK, AND POWER

The derived units follow the mathematical expressions which relate the quantities. From ‘‘force equals mass times acceleration,’’ the newton (N) is deﬁned as the unbalanced force that imparts an acceleration of 1 meter per second squared to a 1-kilogram mass. Thus, 1 N ¼ 1 kg m=s2 . Work results when a force acts over a distance. A joule of work is equivalent to a newton-meter: 1 J ¼ 1 N m. Work and energy have the same units. Power is the rate at which work is done or the rate at which energy is changed from one form to another. The unit of power, the watt (W), is one joule per second (J/s). Table 1-1 Quantity length mass time current

Symbol L; l M; m T; t I; i

SI Unit meter kilogram second ampere

Abbreviation m kg s A

1 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

2

INTRODUCTION

[CHAP. 1

Table 1-2 Quantity electric charge electric potential resistance conductance inductance capacitance frequency force energy, work power magnetic ﬂux magnetic ﬂux density

Symbol

SI Unit

Abbreviation

Q; q V; v R G L C f F; f W; w P; p B

coulomb volt ohm siemens henry farad hertz newton joule watt weber tesla

C V S H F Hz N J W Wb T

EXAMPLE 1.1. In simple rectilinear motion a 10-kg mass is given a constant acceleration of 2.0 m/s2 . (a) Find the acting force F. (b) If the body was at rest at t ¼ 0, x ¼ 0, ﬁnd the position, kinetic energy, and power for t ¼ 4 s. F ¼ ma ¼ ð10 kgÞð2:0 m=s2 Þ ¼ 20:0 kg m=s2 ¼ 20:0 N

ðaÞ ðbÞ

1.3

At t ¼ 4 s;

x ¼ 12 at2 ¼ 12 ð2:0 m=s2 Þð4 sÞ2 ¼ 16:0 m KE ¼ Fx ¼ ð20:0 NÞð16:0 mÞ ¼ 3200 N m ¼ 3:2 kJ P ¼ KE=t ¼ 3:2 kJ=4 s ¼ 0:8 kJ=s ¼ 0:8 kW

ELECTRIC CHARGE AND CURRENT

The unit of current, the ampere (A), is deﬁned as the constant current in two parallel conductors of inﬁnite length and negligible cross section, 1 meter apart in vacuum, which produces a force between the conductors of 2:0 107 newtons per meter length. A more useful concept, however, is that current results from charges in motion, and 1 ampere is equivalent to 1 coulomb of charge moving across a ﬁxed surface in 1 second. Thus, in time-variable functions, iðAÞ ¼ dq=dtðC/s). The derived unit of charge, the coulomb (C), is equivalent to an ampere-second. The moving charges may be positive or negative. Positive ions, moving to the left in a liquid or plasma suggested in Fig. 1-1(a), produce a current i, also directed to the left. If these ions cross the plane surface S at the rate of one coulomb per second, then the resulting current is 1 ampere. Negative ions moving to the right as shown in Fig. 1-1(b) also produce a current directed to the left. Table 1-3 Preﬁx

Factor

Symbol

pico nano micro milli centi deci kilo mega giga tera

12

p n m m c d k M G T

10 109 106 103 102 101 103 106 109 1012

CHAP. 1]

INTRODUCTION

3

Fig. 1-1

Of more importance in electric circuit analysis is the current in metallic conductors which takes place through the motion of electrons that occupy the outermost shell of the atomic structure. In copper, for example, one electron in the outermost shell is only loosely bound to the central nucleus and moves freely from one atom to the next in the crystal structure. At normal temperatures there is constant, random motion of these electrons. A reasonably accurate picture of conduction in a copper conductor is that approximately 8:5 1028 conduction electrons per cubic meter are free to move. The electron charge is e ¼ 1:602 1019 C, so that for a current of one ampere approximately 6:24 1018 electrons per second would have to pass a ﬁxed cross section of the conductor. EXAMPLE 1.2. A conductor has a constant current of ﬁve amperes. How many electrons pass a ﬁxed point on the conductor in one minute? 5 A ¼ ð5 C=sÞð60 s=minÞ ¼ 300 C=min 300 C=min ¼ 1:87 1021 electrons=min 1:602 1019 C=electron

1.4

ELECTRIC POTENTIAL

An electric charge experiences a force in an electric ﬁeld which, if unopposed, will accelerate the particle containing the charge. Of interest here is the work done to move the charge against the ﬁeld as suggested in Fig. 1-2(a). Thus, if 1 joule of work is required to move the charge Q, 1 coulomb from position 0 to position 1, then position 1 is at a potential of 1 volt with respect to position 0; 1 V ¼ 1 J=C. This electric potential is capable of doing work just as the mass in Fig. 1-2(b), which was raised against the gravitational force g to a height h above the ground plane. The potential energy mgh represents an ability to do work when the mass m is released. As the mass falls, it accelerates and this potential energy is converted to kinetic energy.

Fig. 1-2

4

INTRODUCTION

[CHAP. 1

EXAMPLE 1.3. In an electric circuit an energy of 9.25 mJ is required to transport 0.5 mC from point a to point b. What electric potential diﬀerence exists between the two points? 1 volt ¼ 1 joule per coulomb

1.5

V¼

9:25 106 J ¼ 18:5 V 0:5 106 C

ENERGY AND ELECTRICAL POWER

Electric energy in joules will be encountered in later chapters dealing with capacitance and inductance whose respective electric and magnetic ﬁelds are capable of storing energy. The rate, in joules per second, at which energy is transferred is electric power in watts. Furthermore, the product of voltage and current yields the electric power, p ¼ vi; 1 W ¼ 1 V 1 A. Also, V A ¼ ðJ=CÞ ðC=sÞ ¼ J=s ¼ W. In a more fundamental sense power is the time derivative p ¼ dw=dt, so that instantaneous power p is generally a function of time. In the following chapters time average power Pavg and a root-mean-square (RMS) value for the case where voltage and current are sinusoidal will be developed. EXAMPLE 1.4. A resistor has a potential diﬀerence of 50.0 V across its terminals and 120.0 C of charge per minute passes a ﬁxed point. Under these conditions at what rate is electric energy converted to heat? ð120:0 C=minÞ=ð60 s=minÞ ¼ 2:0 A

P ¼ ð2:0 AÞð50:0 VÞ ¼ 100:0 W

Since 1 W ¼ 1 J/s, the rate of energy conversion is one hundred joules per second.

1.6

CONSTANT AND VARIABLE FUNCTIONS

To distinguish between constant and time-varying quantities, capital letters are employed for the constant quantity and lowercase for the variable quantity. For example, a constant current of 10 amperes is written I ¼ 10:0 A, while a 10-ampere time-variable current is written i ¼ 10:0 f ðtÞ A. Examples of common functions in circuit analysis are the sinusoidal function i ¼ 10:0 sin !t ðAÞ and the exponential function v ¼ 15:0 eat (V).

Solved Problems 1.1

The force applied to an object moving in the x direction varies according to F ¼ 12=x2 (N). (a) Find the work done in the interval 1 m x 3 m. (b) What constant force acting over the same interval would result in the same work? ð3 dW ¼ F dx

ðaÞ

so

W¼ 1

8 J ¼ Fc ð2 mÞ

ðbÞ

1.2

or

3 12 1 dx ¼ 12 ¼ 8J x 1 x2 Fc ¼ 4 N

Electrical energy is converted to heat at the rate of 7.56kJ/min in a resistor which has 270 C/min passing through. What is the voltage diﬀerence across the resistor terminals? From P ¼ VI, V¼

P 7:56 103 J=min ¼ ¼ 28 J=C ¼ 28 V I 270 C=min

CHAP. 1]

1.3

5

INTRODUCTION

A certain circuit element has a current i ¼ 2:5 sin !t (mA), where ! is the angular frequency in rad/s, and a voltage diﬀerence v ¼ 45 sin !t (V) between terminals. Find the average power Pavg and the energy WT transferred in one period of the sine function. Energy is the time-integral of instantaneous power: ð 2=! ð 2=! 112:5 ðmJÞ vi dt ¼ 112:5 sin2 !t dt ¼ WT ¼ ! 0 0 The average power is then Pavg ¼

WT ¼ 56:25 mW 2=!

Note that Pavg is independent of !.

1.4

The unit of energy commonly used by electric utility companies is the kilowatt-hour (kWh). (a) How many joules are in 1 kWh? (b) A color television set rated at 75 W is operated from 7:00 p.m. to 11:30 p.m. What total energy does this represent in kilowatt-hours and in megajoules? (a) 1 kWh ¼ ð1000 J=sÞð3600 s=hÞ ¼ 3:6 MJ (b) ð75:0 WÞð4:5 hÞ ¼ 337:5 Wh ¼ 0:3375 kWh ð0:3375 kWhÞð3:6 MJ=kWhÞ ¼ 1:215 MJ

1.5

An AWG #12 copper wire, a size in common use in residential wiring, contains approximately 2:77 1023 free electrons per meter length, assuming one free conduction electron per atom. What percentage of these electrons will pass a ﬁxed cross section if the conductor carries a constant current of 25.0 A? 25:0 C=s ¼ 1:56 1020 electron=s 1:602 1019 C=electron ð1:56 1020 electrons=sÞð60 s=minÞ ¼ 9:36 1021 electrons=min 9:36 1021 ð100Þ ¼ 3:38% 2:77 1023

1.6

How many electrons pass a ﬁxed point in a 100-watt light bulb in 1 hour if the applied constant voltage is 120 V? 100 W ¼ ð120 VÞ IðAÞ

I ¼ 5=6 A

ð5=6 C=sÞð3600 s=hÞ ¼ 1:87 1022 electrons per hour 1:602 1019 C=electron

1.7

A typical 12 V auto battery is rated according to ampere-hours. A 70-A h battery, for example, at a discharge rate of 3.5 A has a life of 20 h. (a) Assuming the voltage remains constant, obtain the energy and power delivered in a complete discharge of the preceding batttery. (b) Repeat for a discharge rate of 7.0 A. (a) ð3:5 AÞð12 VÞ ¼ 42:0 W (or J/s) ð42:0 J=sÞð3600 s=hÞð20 hÞ ¼ 3:02 MJ (b) ð7:0 AÞð12 VÞ ¼ 84:0 W ð84:0 J=sÞð3600 s=hÞð10 hÞ ¼ 3:02 MJ

6

INTRODUCTION

[CHAP. 1

The ampere-hour rating is a measure of the energy the battery stores; consequently, the energy transferred for total discharge is the same whether it is transferred in 10 hours or 20 hours. Since power is the rate of energy transfer, the power for a 10-hour discharge is twice that in a 20-hour discharge.

Supplementary Problems 1.8

Obtain the work and power associated with a force of 7:5 104 N acting over a distance of 2 meters in an elapsed time of 14 seconds. Ans. 1.5 mJ, 0.107 mW

1.9

Obtain the work and power required to move a 5.0-kg mass up a frictionless plane inclined at an angle of 308 with the horizontal for a distance of 2.0 m along the plane in a time of 3.5 s. Ans. 49.0 J, 14.0 W

1.10

Work equal to 136.0 joules is expended in moving 8:5 1018 electrons between two points in an electric circuit. What potential diﬀerence does this establish between the two points? Ans. 100 V

1.11

A pulse of electricity measures 305 V, 0.15 A, and lasts 500 ms. What power and energy does this represent? Ans. 45.75 W, 22.9 mJ

1.12

A unit of power used for electric motors is the horsepower (hp), equal to 746 watts. How much energy does a 5-hp motor deliver in 2 hours? Express the answer in MJ. Ans. 26.9 MJ

1.13

For t 0, q ¼ ð4:0 104 Þð1 e250t Þ (C).

1.14

A certain circuit element has the current and voltage

Obtain the current at t ¼ 3 ms.

i ¼ 10e5000t ðAÞ Find the total energy transferred during t 0.

1.15

Ans.

47.2 mA

v ¼ 50ð1 e5000t Þ ðVÞ Ans.

50 mJ

The capacitance of a circuit element is deﬁned as Q=V, where Q is the magnitude of charge stored in the element and V is the magnitude of the voltage diﬀerence across the element. The SI derived unit of capacitance is the farad (F). Express the farad in terms of the basic units. Ans. 1 F ¼ 1 A2 s4 =kg m2

Circuit Concepts 2.1

PASSIVE AND ACTIVE ELEMENTS

An electrical device is represented by a circuit diagram or network constructed from series and parallel arrangements of two-terminal elements. The analysis of the circuit diagram predicts the performance of the actual device. A two-terminal element in general form is shown in Fig. 2-1, with a single device represented by the rectangular symbol and two perfectly conducting leads ending at connecting points A and B. Active elements are voltage or current sources which are able to supply energy to the network. Resistors, inductors, and capacitors are passive elements which take energy from the sources and either convert it to another form or store it in an electric or magnetic ﬁeld.

Fig. 2-1

Figure 2-2 illustrates seven basic circuit elements. Elements (a) and (b) are voltage sources and (c) and (d) are current sources. A voltage source that is not aﬀected by changes in the connected circuit is an independent source, illustrated by the circle in Fig. 2-2(a). A dependent voltage source which changes in some described manner with the conditions on the connected circuit is shown by the diamond-shaped symbol in Fig. 2-2(b). Current sources may also be either independent or dependent and the corresponding symbols are shown in (c) and (d). The three passive circuit elements are shown in Fig. 2-2(e), ( f ), and (g). The circuit diagrams presented here are termed lumped-parameter circuits, since a single element in one location is used to represent a distributed resistance, inductance, or capacitance. For example, a coil consisting of a large number of turns of insulated wire has resistance throughout the entire length of the wire. Nevertheless, a single resistance lumped at one place as in Fig. 2-3(b) or (c) represents the distributed resistance. The inductance is likewise lumped at one place, either in series with the resistance as in (b) or in parallel as in (c). 7 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

8

CIRCUIT CONCEPTS

[CHAP. 2

Fig. 2-2

Fig. 2-3

In general, a coil can be represented by either a series or a parallel arrangement of circuit elements. The frequency of the applied voltage may require that one or the other be used to represent the device.

2.2

SIGN CONVENTIONS

A voltage function and a polarity must be speciﬁed to completely describe a voltage source. The polarity marks, þ and , are placed near the conductors of the symbol that identiﬁes the voltage source. If, for example, v ¼ 10:0 sin !t in Fig. 2-4(a), terminal A is positive with respect to B for 0 > !t > , and B is positive with respect to A for > !t > 2 for the ﬁrst cycle of the sine function.

Fig. 2-4

Similarly, a current source requires that a direction be indicated, as well as the function, as shown in Fig. 2-4(b). For passive circuit elements R, L, and C, shown in Fig. 2-4(c), the terminal where the current enters is generally treated as positive with respect to the terminal where the current leaves. The sign on power is illustrated by the dc circuit of Fig. 2-5(a) with constant voltage sources VA ¼ 20:0 V and VB ¼ 5:0 V and a single 5- resistor. The resulting current of 3.0 A is in the clockwise direction. Considering now Fig. 2-5(b), power is absorbed by an element when the current enters the element at the positive terminal. Power, computed by VI or I 2 R, is therefore absorbed by both the resistor and the VB source, 45.0 W and 15 W respectively. Since the current enters VA at the negative terminal, this element is the power source for the circuit. P ¼ VI ¼ 60:0 W conﬁrms that the power absorbed by the resistor and the source VB is provided by the source VA .

CHAP. 2]

9

CIRCUIT CONCEPTS

Fig. 2-5

2.3

VOLTAGE-CURRENT RELATIONS

The passive circuit elements resistance R, inductance L, and capacitance C are deﬁned by the manner in which the voltage and current are related for the individual element. For example, if the voltage v and current i for a single element are related by a constant, then the element is a resistance, R is the constant of proportionality, and v ¼ Ri. Similarly, if the voltage is the time derivative of the current, then the element is an inductance, L is the constant of proportionality, and v ¼ L di=dt. Finally, if the current in the element is the time derivative of the voltage, then the element is a capacitance, C is the constant of proportionality, and i ¼ C dv=dt. Table 2-1 summarizes these relationships for the three passive circuit elements. Note the current directions and the corresponding polarity of the voltages.

Table 2-1 Circuit element

Units

Voltage

Current

ohms ()

v ¼ Ri (Ohms’s law)

Power

i¼

v R

p ¼ vi ¼ i2 R

Resistance

v¼L

henries (H)

di dt

i¼

1 L

ð v dt þ k1

p ¼ vi ¼ Li

di dt

p ¼ vi ¼ Cv

dv dt

Inductance

farads (F)

Capacitance

v¼

1 C

ð i dt þ k2

i¼C

dv dt

10

2.4

CIRCUIT CONCEPTS

[CHAP. 2

RESISTANCE

All electrical devices that consume energy must have a resistor (also called a resistance) in their circuit model. Inductors and capacitors may store energy but over time return that energy to the source or to another circuit element. Power in the resistor, given by p ¼ vi ¼ i2 R ¼ v2 =R, is always positive as illustrated in Example 2.1 below. Energy is then determined as the integral of the instantaneous power ð ð t2 ð t2 1 t2 2 2 w¼ p dt ¼ R i dt ¼ v dt R t1 t1 t1 EXAMPLE 2.1. A 4.0- resistor has a current i ¼ 2:5 sin !t (A). Find the voltage, power, and energy over one cycle. ! ¼ 500 rad/s. v ¼ Ri ¼ 10:0 sin !t ðVÞ p ¼ vi ¼ i2 R ¼ 25:0 sin2 !t ðWÞ ðt t sin 2!t ðJÞ w ¼ p dt ¼ 25:0 2 4! 0 The plots of i, p, and w shown in Fig. 2-6 illustrate that p is always positive and that the energy w, although a function of time, is always increasing. This is the energy absorbed by the resistor.

Fig. 2-6

CHAP. 2]

2.5

11

CIRCUIT CONCEPTS

INDUCTANCE

The circuit element that stores energy in a magnetic ﬁeld is an inductor (also called an inductance). With time-variable current, the energy is generally stored during some parts of the cycle and then returned to the source during others. When the inductance is removed from the source, the magnetic ﬁeld will collapse; in other words, no energy is stored without a connected source. Coils found in electric motors, transformers, and similar devices can be expected to have inductances in their circuit models. Even a set of parallel conductors exhibits inductance that must be considered at most frequencies. The power and energy relationships are as follows. di d 1 2 i¼ Li p ¼ vi ¼ L dt dt 2 ð t2 ð t2 1 wL ¼ p dt ¼ Li dt ¼ L½i22 i12 2 t1 t1 Energy stored in the magnetic ﬁeld of an inductance is wL ¼ 12 Li2 . EXAMPLE 2.2. In the interval 0 > t > ð=50Þ s a 30-mH inductance has a current i ¼ 10:0 sin 50t (A). Obtain the voltage, power, and energy for the inductance. v¼L

di ¼ 15:0 cos 50t ðVÞ dt

ðt p ¼ vi ¼ 75:0 sin 100t ðWÞ

p dt ¼ 0:75ð1 cos 100tÞ ðJÞ

wL ¼ 0

As shown in Fig. 2-7, the energy is zero at t ¼ 0 and t ¼ ð=50Þ s. Thus, while energy transfer did occur over the interval, this energy was ﬁrst stored and later returned to the source.

Fig. 2-7

12

CIRCUIT CONCEPTS

2.6

[CHAP. 2

CAPACITANCE

The circuit element that stores energy in an electric ﬁeld is a capacitor (also called capacitance). When the voltage is variable over a cycle, energy will be stored during one part of the cycle and returned in the next. While an inductance cannot retain energy after removal of the source because the magnetic ﬁeld collapses, the capacitor retains the charge and the electric ﬁeld can remain after the source is removed. This charged condition can remain until a discharge path is provided, at which time the energy is released. The charge, q ¼ Cv, on a capacitor results in an electric ﬁeld in the dielectric which is the mechanism of the energy storage. In the simple parallel-plate capacitor there is an excess of charge on one plate and a deﬁciency on the other. It is the equalization of these charges that takes place when the capacitor is discharged. The power and energy relationships for the capacitance are as follows. dv d 1 p ¼ vi ¼ Cv ¼ Cv2 dt dt 2 ð t2 ð t2 1 wC ¼ p dt ¼ Cv dv ¼ C½v22 v21 2 t1 t1 The energy stored in the electric ﬁeld of capacitance is wC ¼ 12 Cv2 . EXAMPLE 2.3. In the interval 0 > t > 5 ms, a 20-mF capacitance has a voltage v ¼ 50:0 sin 200t (V). Obtain the charge, power, and energy. Plot wC assuming w ¼ 0 at t ¼ 0. q ¼ Cv ¼ 1000 sin 200t ðmCÞ dv ¼ 0:20 cos 200t ðAÞ dt p ¼ vi ¼ 5:0 sin 400t ðWÞ ð t2 p dt ¼ 12:5½1 cos 400t ðmJÞ wC ¼ i¼C

t1

In the interval 0 > t > 2:5 ms the voltage and charge increase from zero to 50.0 V and 1000 mC, respectively. Figure 2-8 shows that the stored energy increases to a value of 25 mJ, after which it returns to zero as the energy is returned to the source.

Fig. 2-8

2.7

CIRCUIT DIAGRAMS

Every circuit diagram can be constructed in a variety of ways which may look diﬀerent but are in fact identical. The diagram presented in a problem may not suggest the best of several methods of solution. Consequently, a diagram should be examined before a solution is started and redrawn if necessary to show more clearly how the elements are interconnected. An extreme example is illustrated in Fig. 2-9, where the three circuits are actually identical. In Fig. 2-9(a) the three ‘‘junctions’’ labeled A

CHAP. 2]

13

CIRCUIT CONCEPTS

are shown as two ‘‘junctions’’ in (b). However, resistor R4 is bypassed by a short circuit and may be removed for purposes of analysis. Then, in Fig. 2-9(c) the single junction A is shown with its three meeting branches.

Fig. 2-9

2.8

NONLINEAR RESISTORS

The current-voltage relationship in an element may be instantaneous but not necessarily linear. The element is then modeled as a nonlinear resistor. An example is a ﬁlament lamp which at higher voltages draws proportionally less current. Another important electrical device modeled as a nonlinear resistor is a diode. A diode is a two-terminal device that, roughly speaking, conducts electric current in one direction (from anode to cathode, called forward-biased) much better than the opposite direction (reverse-biased). The circuit symbol for the diode and an example of its current-voltage characteristic are shown in Fig. 2-25. The arrow is from the anode to the cathode and indicates the forward direction ði > 0Þ. A small positive voltage at the diode’s terminal biases the diode in the forward direction and can produce a large current. A negative voltage biases the diode in the reverse direction and produces little current even at large voltage values. An ideal diode is a circuit model which works like a perfect switch. See Fig. 2-26. Its ði; vÞ characteristic is v ¼ 0 when i 0 i ¼ 0 when v 0 The static resistance of a nonlinear resistor operating at ðI; VÞ is R ¼ V=I. Its dynamic resistance is r ¼ V=I which is the inverse of the slope of the current plotted versus voltage. Static and dynamic resistances both depend on the operating point. EXAMPLE 2.4. The current and voltage characteristic of a semiconductor diode in the forward direction is measured and recorded in the following table: v (V) i (mA)

0.5 2 10

4

0.6

0.65

0.66

0.67

0.68

0.69

0.70

0.71

0.11

0.78

1.2

1.7

2.6

3.9

5.8

8.6

0.72 12.9

0.73 19.2

0.74 28.7

0.75 42.7

In the reverse direction (i.e., when v < 0), i ¼ 4 1015 A. Using the values given in the table, calculate the static and dynamic resistances (R and r) of the diode when it operates at 30 mA, and ﬁnd its power consumption p. From the table

14

CIRCUIT CONCEPTS

[CHAP. 2

V 0:74 ¼ 25:78 I 28:7 103 V 0:75 0:73 ¼ 0:85 r¼ I ð42:7 19:2Þ 103

R¼

p ¼ VI 0:74 28:7 103 W ¼ 21:238 mW EXAMPLE 2.5. The current and voltage characteristic of a tungsten ﬁlament light bulb is measured and recorded in the following table. Voltages are DC steady-state values, applied for a long enough time for the lamp to reach thermal equilibrium.

v (V)

0.5

1

1.5

2

3

3.5

4

4.5

5

5.5

6

6.5

7

7.5

8

i (mA)

4

6

8

9

11

12

13

14

15

16

17

18

18

19

20

Find the static and dynamic resistances of the ﬁlament and also the power consumption at the operating points (a) i ¼ 10 mA; (b) i ¼ 15 mA. R¼

V ; I

r¼

V ; I

p ¼ VI

ðaÞ

R

2:5 32 ¼ 250 ; r ¼ 500 ; p 2:5 10 103 W ¼ 25 mW 10 103 ð11 9Þ 103

ðbÞ

R

5 5:5 4:5 ¼ 333 ; r ¼ 500 ; p 5 15 103 W ¼ 75 mW 15 103 ð16 14Þ 103

Solved Problems 2.1

A 25.0- resistance has a voltage v ¼ 150:0 sin 377t (V). Find the corresponding current i and power p. i¼

2.2

v ¼ 6:0 sin 377t ðAÞ R

p ¼ vi ¼ 900:0 sin2 377t ðWÞ

The current in a 5- resistor increases linearly from zero to 10 A in 2 ms. At t ¼ 2þ ms the current is again zero, and it increases linearly to 10 A at t ¼ 4 ms. This pattern repeats each 2 ms. Sketch the corresponding v. Since v ¼ Ri, the maximum voltage must be ð5Þð10Þ ¼ 50 V. In Fig. 2-10 the plots of i and v are shown. The identical nature of the functions is evident.

2.3

An inductance of 2.0 mH has a current i ¼ 5:0ð1 e5000t Þ (A). Find the corresponding voltage and the maximum stored energy. v¼L

di ¼ 50:0e5000t ðVÞ dt

In Fig. 2-11 the plots of i and v are given. Since the maximum current is 5.0 A, the maximum stored energy is Wmax ¼

1 2 ¼ 25:0 mJ LI 2 max

CHAP. 2]

15

CIRCUIT CONCEPTS

Fig. 2-10

Fig. 2-11

2.4

An inductance of 3.0 mH has a voltage that is described as follows: for 0 > t > 2 ms, V ¼ 15:0 V and, for 2 > t > 4 ms, V ¼ 30:0 V. Obtain the corresponding current and sketch vL and i for the given intervals. For 0 > t > 2 ms, i¼

1 L

ðt v dt ¼ 0

1 3 103

ðt

15:0 dt ¼ 5 103 t ðAÞ

0

For t ¼ 2 ms, i ¼ 10:0 A For 2 > t > 4 ms, i¼

1 L

ðt v dt þ 10:0 þ 2103

1 3 103

ðt 30:0 dt 2103

1 ½30:0t þ ð60:0 103 Þ ðAÞ 3 103 ¼ 30:0 ð10 103 tÞ ðAÞ

¼ 10:0 þ

See Fig. 2-12.

2.5

A capacitance of 60.0 mF has a voltage described as follows: 0 > t > 2 ms, v ¼ 25:0 103 t (V). Sketch i, p, and w for the given interval and ﬁnd Wmax . For 0 > t > 2 ms,

16

CIRCUIT CONCEPTS

[CHAP. 2

Fig. 2-12 dv d ¼ 60 106 ð25:0 103 tÞ ¼ 1:5 A dt dt p ¼ vi ¼ 37:5 103 t ðWÞ ðt wC ¼ p dt ¼ 1:875 104 t2 ðmJÞ i¼C

0

See Fig. 2-13.

or

Wmax ¼ ð1:875 104 Þð2 103 Þ2 ¼ 75:0 mJ 1 1 Wmax ¼ CV2max ¼ ð60:0 106 Þð50:0Þ2 ¼ 75:0 mJ 2 2

Fig. 2-13

2.6

A 20.0-mF capacitance is linearly charged from 0 to 400 mC in 5.0 ms. Find the voltage function and Wmax . ! 400 106 q¼ t ¼ 8:0 102 t ðCÞ 5:0 103 v ¼ q=C ¼ 4:0 103 t ðVÞ Vmax ¼ ð4:0 103 Þð5:0 103 Þ ¼ 20:0 V

2.7

Wmax ¼

1 CV2max ¼ 4:0 mJ 2

A series circuit with R ¼ 2, L ¼ 2 mH, and C ¼ 500 mF has a current which increases linearly from zero to 10 A in the interval 0 t 1 ms, remains at 10 A for 1 ms t 2 ms, and decreases linearly from 10 A at t ¼ 2 ms to zero at t ¼ 3 ms. Sketch vR , vL , and vC . vR must be a time function identical to i, with Vmax ¼ 2ð10Þ ¼ 20 V. For 0 < t < 1 ms, di ¼ 10 103 A=s dt When di=dt ¼ 0, for 1 ms < t < 2 ms, vL ¼ 0.

and

vL ¼ L

di ¼ 20 V dt

CHAP. 2]

CIRCUIT CONCEPTS

17

Assuming zero initial charge on the capacitor, 1 C

vC ¼

ð i dt

For 0 t 1 ms, vC ¼

1 5 104

ðt

104 t dt ¼ 107 t2 ðVÞ

0

This voltage reaches a value of 10 V at 1 ms.

For 1 ms < t < 2 ms, 3

vC ¼ ð20 10 Þðt 103 Þ þ 10 ðVÞ See Fig. 2-14.

Fig. 2-14

2.8

A single circuit element has the current and voltage functions graphed in Fig. 2-15. Determine the element.

Fig. 2-15

18

CIRCUIT CONCEPTS

[CHAP. 2

The element cannot be a resistor since v and i are not proportional. v is an integral of i. For 2 ms < t < 4 ms, i 6¼ 0 but v is constant (zero); hence the element cannot be a capacitor. For 0 < t < 2 ms, di ¼ 5 103 A=s dt

and

v ¼ 15 V

Consequently, L¼v

di ¼ 3 mH dt

(Examine the interval 4 ms < t < 6 ms; L must be the same.)

2.9

Obtain the voltage v in the branch shown in Fig. 2-16 for (c) i2 ¼ 0 A.

(a) i2 ¼ 1 A, (b) i2 ¼ 2 A,

Voltage v is the sum of the current-independent 10-V source and the current-dependent voltage source vx . Note that the factor 15 multiplying the control current carries the units . ðaÞ

v ¼ 10 þ vx ¼ 10 þ 15ð1Þ ¼ 25 V

ðbÞ

v ¼ 10 þ vx ¼ 10 þ 15ð2Þ ¼ 20 V

ðcÞ

v ¼ 10 þ 15ð0Þ ¼ 10 V

Fig. 2-16

2.10

Find the power absorbed by the generalized circuit element in Fig. 2-17, for (b) v ¼ 50 V.

Fig. 2-17 Since the current enters the element at the negative terminal, ðaÞ ðbÞ

2.11

p ¼ vi ¼ ð50Þð8:5Þ ¼ 425 W p ¼ vi ¼ ð50Þð8:5Þ ¼ 425 W

Find the power delivered by the sources in the circuit of Fig. 2-18. i¼ The powers absorbed by the sources are:

20 50 ¼ 10 A 3

(a) v ¼ 50 V,

CHAP. 2]

CIRCUIT CONCEPTS

19

Fig. 2-18 pa ¼ va i ¼ ð20Þð10Þ ¼ 200 W pb ¼ vb i ¼ ð50Þð10Þ ¼ 500 W Since power delivered is the negative of power absorbed, source vb delivers 500 W and source va absorbs 200 W. The power in the two resistors is 300 W.

2.12

A 25.0- resistance has a voltage v ¼ 150:0 sin 377t (V). Find the power p and the average power pavg over one cycle. i ¼ v=R ¼ 6:0 sin 377t ðAÞ p ¼ vi ¼ 900:0 sin2 377t ðWÞ The end of one period of the voltage and current functions occurs at 377t ¼ 2. integration is taken over one-half cycle, 377t ¼ . Thus, ð 1 Pavg ¼ 900:0 sin2 ð377tÞdð377tÞ ¼ 450:0 ðWÞ 0

2.13

For Pavg the

Find the voltage across the 10.0- resistor in Fig. 2-19 if the control current ix in the dependent source is (a) 2 A and (b) 1 A. i ¼ 4ix 4:0; vR ¼ iR ¼ 40:0ix 40:0 ðVÞ ix ¼ 2; vR ¼ 40:0 V ix ¼ 1;

vR ¼ 80:0 V

Fig. 2-19

Supplementary Problems 2.14

A resistor has a voltage of V ¼ 1:5 mV. (b) 1.20 mW. Ans. 18.5 mA, 0.8 mA

Obtain the current if the power absorbed is (a) 27.75 nW and

20

CIRCUIT CONCEPTS

[CHAP. 2

2.15

A resistance of 5.0 has a current i ¼ 5:0 103 t (A) in the interval 0 t 2 ms. and average power. Ans. 125.0t2 (W), 167.0 (W)

2.16

Current i enters a generalized circuit element at the positive terminal and the voltage across the element is 3.91 V. If the power absorbed is 25:0 mW, obtain the current. Ans. 6:4 mA

2.17

Determine the single circuit element for which the current and voltage in the interval 0 103 t are given by i ¼ 2:0 sin 103 t (mA) and v ¼ 5:0 cos 103 t (mV). Ans. An inductance of 2.5 mH

2.18

An inductance of 4.0 mH has a voltage v ¼ 2:0e10 t (V). Obtain the maximum stored energy. the current is zero. Ans. 0.5 mW

2.19

A capacitance of 2.0 mF with an initial charge Q0 is switched into a series circuit consisting of a 10.0- resistance. Find Q0 if the energy dissipated in the resistance is 3.6 mJ. Ans. 120.0 mC

2.20

Given that a capactance of C farads has a current i ¼ ðVm =RÞet=ðRcÞ (A), show that the maximum stored energy is 12 CVm2 . Assume the initial charge is zero.

2.21

The current after t ¼ 0 in a single circuit element is as shown in Fig. 2-20. Find the voltage across the element at t ¼ 6:5 ms, if the element is (a) 10 k, (b) 15 mH, (c) 0.3 nF with Qð0Þ ¼ 0. Ans. (a) 25 V; (b) 75 V; (c) 81.3 V

3

Obtain the instantaneous

At t ¼ 0,

Fig. 2-20 2.22

The 20.0-mF capacitor in the circuit shown in Fig. 2-21 has a voltage for t > 0, v ¼ 100:0et=0:015 (V). Obtain the energy function that accompanies the discharge of the capacitor and compare the total energy to that which is absorbed by the 750- resistor. Ans. 0.10 ð1 et=0:0075 Þ (J)

Fig. 2-21 2.23

Find the current i in the circuit shown in Fig. 2-22, if the control v2 of the dependent voltage source has the value (a) 4 V, (b) 5 V, (c) 10 V. Ans. (a) 1 A; (b) 0 A; (c) 5 A

2.24

In the circuit shown in Fig. 2-23, ﬁnd the current, i, given (a) i1 ¼ 2 A, i2 ¼ 0; (c) i1 ¼ i2 ¼ 1 A. Ans. (a) 10 A; (b) 11 A; (c) 9A

2.25

A 1-mF capacitor with an initial charge of 104 C is connected to a resistor R at t ¼ 0. Assume discharge current during 0 < t < 1 ms is constant. Approximate the capacitor voltage drop at t ¼ 1 ms for

(b) i1 ¼ 1 A; i2 ¼ 4 A;

CHAP. 2]

21

CIRCUIT CONCEPTS

Fig. 2-22

Fig. 2-23 (a) R ¼ 1 M; (b) R ¼ 100 k; (c) R ¼ 10 k. Hint: Compute the charge lost during the 1-ms period. Ans. (a) 0.1 V; (b) 1 V; (b) 10 V 6

2.26

The actual discharge current in Problem 2.25 is i ¼ ð100=RÞe10 t=R A. Find the capacitor voltage drop at 1 ms after connection to the resistor for (a) R ¼ 1 M; (b) R ¼ 100 k; (c) R ¼ 10 k. Ans. (a) 0.1 V; (b) 1 V; (c) 9.52 V

2.27

A 10-mF capacitor discharges in an element such that its voltage is v ¼ 2e1000t . delivered by the capacitor as functions of time. Ans. i ¼ 20e1000t mA, p ¼ vi ¼ 40e1000t mJ

2.28

Find voltage v, current i, and energy W in the capacitor of Problem 2.27 at time t ¼ 0, 1, 3, 5, and 10 ms. By integrating the power delivered by the capacitor, show that the energy dissipated in the element during the interval from 0 to t is equal to the energy lost by the capacitor. Ans.

t

v

i

W

0

2V

20 mA

20 mJ

1 ms

736 mV

7.36 mA

2.7 mJ

3 ms

100 mV

1 mA

0.05 mJ

5 ms

13.5 mV

135 mA

0:001 mJ

10 ms

91 mV

0.91 mA

0

Find the current and power

2.29

The current delivered by a current source is increased linearly from zero to 10 A in 1-ms time and then is decreased linearly back to zero in 2 ms. The source feeds a 3-k resistor in series with a 2-H inductor (see Fig. 2-24). (a) Find the energy dissipated in the resistor during the rise time ðW1 Þ and the fall time ðW2 Þ. (b) Find the energy delivered to the inductor during the above two intervals. (c) Find the energy delivered by the current source to the series RL combination during the preceding two intervals. Note: Series elements have the same current. The voltage drop across their combination is the sum of their individual voltages. Ans. ðaÞ W1 ¼ 100; W2 ¼ 200; (b) W1 ¼ 200; W2 ¼ 200; (c) W1 ¼ 300; W2 ¼ 0, all in joules

2.30

The voltage of a 5-mF capacitor is increased linearly from zero to 10 V in 1 ms time and is then kept at that level. Find the current. Find the total energy delivered to the capacitor and verify that delivered energy is equal to the energy stored in the capacitor. Ans. i ¼ 50 mA during 0 < t < 1 ms and is zero elsewhere, W ¼ 250 mJ.

22

CIRCUIT CONCEPTS

[CHAP. 2

Fig. 2-24

2.31

A 10-mF capacitor is charged to 2 V. A path is established between its terminals which draws a constant current of I0 . (a) For I0 ¼ 1 mA, how long does it take to reduce the capacitor voltage to 5 percent of its initial value? (b) For what value of I0 does the capacitor voltage remain above 90 percent of its initial value after passage of 24 hours? Ans. (a) 19 ms, (b) 23.15pA

2.32

Energy gained (or lost) by an electric charge q traveling in an electric ﬁeld is qv, where v is the electric potential gained (or lost). In a capacitor with charge Q and terminal voltage V, let all charges go from one plate to the other. By way of computation, show that the total energy W gained (or lost) is not QV but QV=2 and explain why. Also note that QV=2 is equal to the initial energy content of the capacitor. Ð Ans. W ¼ qvdt ¼ Q V0 ¼ QV=2 ¼ 12 CV 2 . The apparent discrepancy is explained by the following. 2 The starting voltage vetween the two plates is V. As the charges migrate from one plate of the capacitor to the other plate, the voltage between the two plates drops and becomes zero when all charges have moved. The average of the voltage during the migration process is V=2, and therefore, the total energy is QV=2.

2.33

Lightning I. The time proﬁle of the discharge current in a typical cloud-to-ground lightning stroke is modeled by a triangle. The surge takes 1 ms to reach the peak value of 100 kA and then is reduced to zero in 99 mS. (a) Find the electric charge Q discharged. (b) If the cloud-to-ground voltage before the discharge is 400 MV, ﬁnd the total energy W released and the average power P during the discharge. (c) If during the storm there is an average of 18 such lightning strokes per hour, ﬁnd the average power released in 1 hour. Ans. (a) Q ¼ 5 C; (b) W ¼ 109 J; P ¼ 1013 W; (c) 5 MW

2.34

Lightning II. Find the cloud-to-ground capacitance in Problem 2.33 just before the lightning stroke. Ans. 12.5 mF

2.35

Lightning III. The current in a cloud-to-ground lightning stroke starts at 200 kA and diminishes linearly to zero in 100 ms. Find the energy released W and the capacitance of the cloud to ground C if the voltage before the discharge is (a) 100 MV; (b) 500 MV. Ans. (a) W ¼ 5 108 J; C ¼ 0:1 mF; (b) W ¼ 25 108 J; C ¼ 20 nF

2.36

The semiconductor diode of Example 2.4 is placed in the circuit of Fig. 2-25. (a) Vs ¼ 1 V, (b) Vs ¼ 1 V. Ans. (a) 14 mA; (b) 0

2.37

The diode in the circuit of Fig. 2-26 is ideal. The inductor draws 100 mA from the voltage source. A 2-mF capacitor with zero initial charge is also connected in parallel with the inductor through an ideal diode such that the diode is reversed biased (i.e., it blocks charging of the capacitor). The switch s suddenly disconnects with the rest of the circuit, forcing the inductor current to pass through the diode and establishing 200 V at the capacitor’s terminals. Find the value of the inductor. Ans. L ¼ 8 H

2.38

Compute the static and dynamic resistances of the diode of Example 2.4 at the operating point v ¼ 0:66 V. Ans:

R

0:66 0:67 0:65 ¼ 550 and r ¼ 21:7 1:2 103 ð1:7 0:78Þ 103

Find the current for

CHAP. 2]

CIRCUIT CONCEPTS

23

Fig. 2-25

Fig. 2-26

2.39

The diode of Example 2.4 operates within the range 10 < i < 20 mA. Within that range, approximate its terminal characteristic by a straight line i ¼ v þ , by specifying and . Ans. i ¼ 630 v 4407 mA, where v is in V

2.40

The diode of Example 2.4 operates within the range of 20 < i < 40 mA. Within that range, approximate its terminal characteristic by a straight line connecting the two operating limits. Ans. i ¼ 993:33 v 702:3 mA, where v is in V

2.41

Within the operating range of 20 < i < 40 mA, model the diode of Example 2.4 by a resistor R in series with a voltage source V such that the model matches exactly with the diode performance at 0.72 and 0.75 V. Find R and V. Ans. R ¼ 1:007 ; V ¼ 707 mV

Circuit Laws 3.1

INTRODUCTION

An electric circuit or network consists of a number of interconnected single circuit elements of the type described in Chapter 2. The circuit will generally contain at least one voltage or current source. The arrangement of elements results in a new set of constraints between the currents and voltages. These new constraints and their corresponding equations, added to the current-voltage relationships of the individual elements, provide the solution of the network. The underlying purpose of deﬁning the individual elements, connecting them in a network, and solving the equations is to analyze the performance of such electrical devices as motors, generators, transformers, electrical transducers, and a host of electronic devices. The solution generally answers necessary questions about the operation of the device under conditions applied by a source of energy.

3.2

KIRCHHOFF’S VOLTAGE LAW

For any closed path in a network, Kirchhoﬀ’s voltage law (KVL) states that the algebraic sum of the voltages is zero. Some of the voltages will be sosurces, while others will result from current in passive elements creating a voltage, which is sometimes referred to as a voltage drop. The law applies equally well to circuits driven by constant sources, DC, time variable sources, vðtÞ and iðtÞ, and to circuits driven by sources which will be introduced in Chapter 9. The mesh current method of circuit analysis introduced in Section 4.2 is based on Kirchhoﬀ’s voltage law. EXAMPLE 3.1. Write the KVL equation for the circuit shown in Fig. 3-1.

Fig. 3-1

24 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

CHAP. 3]

CIRCUIT LAWS

25

Starting at the lower left corner of the circuit, for the current direction as shown, we have va þ v1 þ vb þ v2 þ v3 ¼ 0 va þ iR1 þ vb þ iR2 þ iR3 ¼ 0 va vb ¼ iðR1 þ R2 þ R3 Þ

3.3

KIRCHHOFF’S CURRENT LAW

The connection of two or more circuit elements creates a junction called a node. The junction between two elements is called a simple node and no division of current results. The junction of three or more elements is called a principal node, and here current division does take place. Kirchhoﬀ’s current law (KCL) states that the algrebraic sum of the currents at a node is zero. It may be stated alternatively that the sum of the currents entering a node is equal to the sum of the currents leaving that node. The node voltage method of circuit analysis introduced in Section 4.3 is based on equations written at the principal nodes of a network by applying Kirchhoﬀ’s current law. The basis for the law is the conservation of electric charge. EXAMPLE 3.2.

Write the KCL equation for the principal node shown in Fig. 3-2. i1 i2 þ i3 i4 i5 ¼ 0 i1 þ i3 ¼ i2 þ i4 þ i5

Fig. 3-2

3.4

CIRCUIT ELEMENTS IN SERIES

Three passive circuit elements in series connection as shown in Fig. 3-3 have the same current i. The voltages across the elements are v1 , v2 , and v3 . The total voltage v is the sum of the individual voltages; v ¼ v1 þ v2 þ v3 .

Fig. 3-3

If the elements are resistors,

26

CIRCUIT LAWS

[CHAP. 3

v ¼ iR1 þ iR2 þ iR3 ¼ iðR1 þ R2 þ R3 Þ ¼ iReq where a single equivalent resistance Req replaces the three series resistors. between i and v will pertain. For any number of resistors in series, we have Req ¼ R1 þ R2 þ . If the three passive elements are inductances,

The same relationship

di di di þ L2 þ L3 dt dt dt di ¼ ðL1 þ L2 þ L3 Þ dt di ¼ Leq dt

v ¼ L1

Extending this to any number of inductances in series, we have Leq ¼ L1 þ L2 þ . If the three circuit elements are capacitances, assuming zero initial charges so that the constants of integration are zero, ð ð ð 1 1 1 v¼ i dt þ i dt þ i dt C1 C2 C3 ð 1 1 1 i dt þ þ ¼ C1 C2 C3 ð 1 ¼ i dt Ceq The equivalent capacitance of several capacitances in series is 1=Ceq ¼ 1=C1 þ 1=C2 þ . EXAMPLE 3.3. The equivalent resistance of three resistors in series is 750.0 . Two of the resistors are 40.0 and 410.0 . What must be the ohmic resistance of the third resistor? Req ¼ R1 þ R2 þ R3 750:0 ¼ 40:0 þ 410:0 þ R3

and

R3 ¼ 300:0

EXAMPLE 3.4. Two capacitors, C1 ¼ 2:0 mF and C2 ¼ 10:0 mF, are connected in series. capacitance. Repeat if C2 is 10.0 pF. Ceq ¼

Find the equivalent

C1 C2 ð2:0 106 Þð10:0 106 Þ ¼ ¼ 1:67 mF C1 þ C2 2:0 106 þ 10:0 106

If C2 ¼ 10:0 pF, Ceq ¼

ð2:0 106 Þð10:0 1012 Þ 20:0 1018 ¼ ¼ 10:0 pF 2:0 106 2:0 106 þ 10:0 1012

where the contribution of 10:0 1012 to the sum C1 þ C2 in the denominator is negligible and therefore it can be omitted.

Note: When two capacitors in series diﬀer by a large amount, the equivalent capacitance is essentially equal to the value of the smaller of the two.

3.5

CIRCUIT ELEMENTS IN PARALLEL

For three circuit elements connected in parallel as shown in Fig. 3-4, KCL states that the current i entering the principal node is the sum of the three currents leaving the node through the branches.

CHAP. 3]

27

CIRCUIT LAWS

Fig. 3-4

i ¼ i1 þ i2 þ i3 If the three passive circuit elements are resistances, v v v 1 1 1 1 i¼ þ þ ¼ þ þ v v¼ R1 R2 R3 R1 R2 R3 Req For several resistors in parallel, 1 1 1 ¼ þ þ Req R1 R2 The case of two resistors in parallel occurs frequently and deserves special mention. resistance of two resistors in parallel is given by the product over the sum. Req ¼

The equivalent

R1 R2 R1 þ R2

EXAMPLE 3.5. Obtain the equivalent resistance of (a) two 60.0- resistors in parallel and (b) three 60.0-

resistors in parallel. ð60:0Þ2 ¼ 30:0

120:0 1 1 1 1 þ þ Req ¼ 20:0

¼ Req 60:0 60:0 60:0 Req ¼

ðaÞ ðbÞ

Note: For n identical resistors in parallel the equivalent resistance is given by R=n. Combinations of inductances in parallel have similar expressions to those of resistors in parallel: 1 1 1 ¼ þ þ Leq L1 L2

EXAMPLE 3.6.

and, for two inductances,

Leq ¼

L1 L2 L1 þ L2

Two inductances L1 ¼ 3:0 mH and L2 ¼ 6:0 mH are connected in parallel. 1 1 1 ¼ þ Leq 3:0 mH 6:0 mH

and

Find Leq .

Leq ¼ 2:0 mH

With three capacitances in parallel, i ¼ C1

dv dv dv dv dv þ C2 þ C3 ¼ ðC1 þ C2 þ C3 Þ ¼ Ceq dt dt dt dt dt

For several parallel capacitors, Ceq ¼ C1 þ C2 þ , which is of the same form as resistors in series.

28

CIRCUIT LAWS

3.6

[CHAP. 3

VOLTAGE DIVISION

A set of series-connected resistors as shown in Fig. 3-5 is referred to as a voltage divider. The concept extends beyond the set of resistors illustrated here and applies equally to impedances in series, as will be shown in Chapter 9.

Fig. 3-5

Since v1 ¼ iR1 and v ¼ iðR1 þ R2 þ R3 Þ,

v1 ¼ v

R1 R1 þ R2 þ R3

EXAMPLE 3.7. A voltage divider circuit of two resistors is designed with a total resistance of the two resistors equal to 50.0 . If the output voltage is 10 percent of the input voltage, obtain the values of the two resistors in the circuit. v1 ¼ 0:10 v

0:10 ¼

R1 50:0 103

from which R1 ¼ 5:0 and R2 ¼ 45:0 .

3.7

CURRENT DIVISION

A parallel arrangement of resistors as shown in Fig. 3-6 results in a current divider. The ratio of the branch current i1 to the total current i illustrates the operation of the divider.

Fig. 3-6

v v v v þ þ and i1 ¼ R1 R2 R3 R1 i1 1=R1 R2 R3 ¼ ¼ i 1=R1 þ 1=R2 þ 1=R3 R1 R2 þ R1 R3 þ R2 R3 i¼

Then

CHAP. 3]

29

CIRCUIT LAWS

For a two-branch current divider we have i1 R2 ¼ i R1 þ R2 This may be expressed as follows: The ratio of the current in one branch of a two-branch parallel circuit to the total current is equal to the ratio of the resistance of the other branch resistance to the sum of the two resistances. EXAMPLE 3.8. A current of 30.0 mA is to be divided into two branch currents of 20.0 mA and 10.0 mA by a network with an equivalent resistance equal to or greater than 10.0 . Obtain the branch resistances. 20 mA R2 ¼ 30 mA R1 þ R2

10 mA R1 ¼ 30 mA R1 þ R2

R1 R2 10:0

R1 þ R2

Solving these equations yields R1 15:0 and R2 30:0 .

Solved Problems 3.1

Find V3 and its polarity if the current I in the circuit of Fig. 3-7 is 0.40 A.

Fig. 3-7 Assume that V3 has the same polarity as V1 . Applying KVL and starting from the lower left corner, V1 Ið5:0Þ V2 Ið20:0Þ þ V3 ¼ 0 50:0 2:0 10:0 8:0 þ V3 ¼ 0 V3 ¼ 30:0 V Terminal b is positive with respect to terminal a.

3.2

Obtain the currents I1 and I2 for the network shown in Fig. 3-8. a and b comprise one node.

Applying KCL,

2:0 þ 7:0 þ I1 ¼ 3:0 Also, c and d comprise a single node.

I1 ¼ 6:0 A

Thus,

4:0 þ 6:0 ¼ I2 þ 1:0

3.3

or

or

Find the current I for the circuit shown in Fig. 3-9.

I2 ¼ 9:0 A

30

CIRCUIT LAWS

[CHAP. 3

Fig. 3-8

Fig. 3-9 The branch currents within the enclosed area cannot be calculated since no values of the resistors are given. However, KCL applies to the network taken as a single node. Thus, 2:0 3:0 4:0 I ¼ 0

3.4

or

I ¼ 5:0 A

Find the equivalent resistance for the circuit shown in Fig. 3-10.

Fig. 3-10 The two 20- resistors in parallel have an equivalent resistance Req ¼ ½ð20Þð20Þ=ð20 þ 20Þ ¼ 10 . This is in series with the 10- resistor so that their sum is 20 . This in turn is in parallel with the other 20-

resistor so that the overall equivalent resistance is 10 .

3.5

Determine the equivalent inductance of the three parallel inductances shown in Fig. 3-11.

CHAP. 3]

31

CIRCUIT LAWS

Fig. 3-11 The two 20-mH inductances have an equivalent inductance of 10 mH. Since this is in parallel with the 10-mH inductance, the overall equivalent inductance is 5 mH. Alternatively, 1 1 1 1 1 1 1 4 þ þ ¼ ¼ þ þ ¼ Leq L1 L2 L3 10 mH 20 mH 20 mH 20 mH

3.6

or

Leq ¼ 5 mH

Express the total capacitance of the three capacitors in Fig. 3-12.

Fig. 3-12 For C2 and C3 in parallel, Ceq ¼ C2 þ C3 . CT ¼

3.7

Then for C1 and Ceq in series,

C1 Ceq C ðC þ C3 Þ ¼ 1 2 C1 þ Ceq C1 þ C2 þ C3

The circuit shown in Fig. 3-13 is a voltage divider, also called an attenuator. When it is a single resistor with an adjustable tap, it is called a potentiometer, or pot. To discover the eﬀect of loading, which is caused by the resistance R of the voltmeter VM, calculate the ratio Vout =Vin for (a) R ¼ 1, (b) 1 M , (c) 10 k , (d) 1 k . ðaÞ

Vout =Vin ¼

250 ¼ 0:100 2250 þ 250

Fig. 3-13

32

CIRCUIT LAWS

[CHAP. 3

(b) The resistance R in parallel with the 250- resistor has an equivalent resistance Req ¼ ðcÞ ðdÞ

3.8

250ð106 Þ ¼ 249:9

and 250 þ 106 ð250Þð10 000Þ Req ¼ ¼ 243:9

250 þ 10 000 ð250Þð1000Þ ¼ 200:0

Req ¼ 250 þ 1000

Vout =Vin ¼

Vout =Vin ¼ 0:098

and and

249:9 ¼ 0:100 2250 þ 249:9

Vout =Vin ¼ 0:082

Find all branch currents in the network shown in Fig. 3-14(a).

Fig. 3-14 The equivalent resistances to the left and right of nodes a and b are ð12Þð8Þ ¼ 9:8

20 ð6Þð3Þ ¼ ¼ 2:0

9

ReqðleftÞ ¼ 5 þ ReqðrightÞ

Now referring to the reduced network of Fig. 3-14(b), 2:0 ð13:7Þ ¼ 2:32 A 11:8 9:8 ð13:7Þ ¼ 11:38 A I4 ¼ 11:8

I3 ¼

Then referring to the original network, 8 ð2:32Þ ¼ 0:93 A 20 3 I5 ¼ ð11:38Þ ¼ 3:79 A 9

I1 ¼

I2 ¼ 2:32 0:93 ¼ 1:39 A I6 ¼ 11:38 3:79 ¼ 7:59 A

Supplementary Problems 3.9

Find the source voltage V and its polarity in the circuit shown in Fig. 3-15 if (a) I ¼ 2:0 A and (b) I ¼ 2:0 A. Ans. (a) 50 V, b positive; (b) 10 V, a positive.

3.10

Find Req for the circuit of Fig. 3-16 for (a) Rx ¼ 1, Ans. (a) 36 ; (b) 16 ; (c) 20

(b) Rx ¼ 0,

(c) Rx ¼ 5 .

CHAP. 3]

33

CIRCUIT LAWS

Fig. 3-16 Fig. 3-15 3.11

An inductance of 8.0 mH is in series with two inductances in parallel, one of 3.0 mH and the other 6.0 mH. Find Leq . Ans. 10.0 mH

3.12

Show that for the three capacitances of equal value shown in Fig. 3-17 Ceq ¼ 1:5 C:

Fig. 3-17 Fig. 3-18

3.13

Find RH and RO for the voltage divider in Fig. 3-18 so that the current I is limited to 0.5 A when VO ¼ 100 V. Ans: RH ¼ 2 M ; RO ¼ 200

3.14

Using voltage division, calculate V1 and V2 in the network shown in Fig. 3-19.

Ans.

11.4 V, 73.1 V

Fig. 3-20 Fig. 3-19

3.15

Obtain the source current I and the total power delivered to the circuit in Fig. 3-20. Ans. 6.0 A, 228 W

3.16

Show that for four resistors in parallel the current in one branch, for example the branch of R4 , is related to the total current by R0 R1 R2 R3 where R 0 ¼ I4 ¼ IT R4 þ R 0 R1 R2 þ R1 R3 þ R2 R3

34

CIRCUIT LAWS

[CHAP. 3

Note: This is similar to the case of current division in a two-branch parallel circuit where the other resistor has been replaced by R 0 . 3.17

A power transmission line carries current from a 6000-V generator to three loads, A, B, and C. The loads are located at 4, 7, and 10 km from the generator and draw 50, 20, and 100 A, respectively. The resistance of the line is 0.1 /km; see Fig. 3-21. (a) Find the voltage at loads A, B, C. (b) Find the maximum percentage voltage drop from the generator to a load.

Fig. 3-21

Ans. (a) vA ¼ 5928 V; vB ¼ 5889 V; vC ¼ 5859 V; 3.18

(b) 2.35 percent

In the circuit of Fig. 3-22, R ¼ 0 and i1 and i2 are unknown. Find i and vAC . Ans. i ¼ 4 A; vAC ¼ 24 V

Fig. 3-22

3.19

In the circuit of Fig. 3-22, R ¼ 1 and i1 ¼ 2 A. Ans. i ¼ 5 A; i2 ¼ 16 A; vAC ¼ 27 V

Find, i, i2 , and vAC .

3.20

In the circuit of Fig. 3-23, is1 ¼ vs2 ¼ 0, vs1 ¼ 9 V, is2 ¼ 12 A. For the four cases of (a) R ¼ 0, (b) R ¼ 6 , (c) R ¼ 9 , and (d) R ¼ 10 000 , draw the simpliﬁed circuit and ﬁnd iBA and vAC . Hint: A zero voltage source corresponds to a short-circuited element and a zero current source corresponds to an open-circuited element. 8 ðaÞ iBA ¼ 7; vAC ¼ 30 > > > < ðbÞ i ¼ 4:2; v ¼ 21:6 BA AC Ans: ðAll in A and V) > ¼ 3:5; v ðcÞ i > BA AC ¼ 19:5 > : ðdÞ iBA ¼ 0:006 0; vAC ¼ 9:02 9

3.21

In the circuit of Fig. 3-23, vs1 ¼ vs2 ¼ 0; is1 ¼ 6 A; is2 ¼ 12 A: For the four cases of (a) R ¼ 0; ðbÞ R ¼ 6 ; ðcÞ R ¼ 9 ; and ðdÞ R ¼ 10 000 ; draw the simpliﬁed circuit and ﬁnd iBA and vAC . 8 ðaÞ iBA ¼ 6; vAC ¼ 36 > > > < ðbÞ iBA ¼ 3:6; vAC ¼ 28:8 Ans: ðAll in A and V) > > > ðcÞ iBA ¼ 3; vAC ¼ 27 : ðdÞ iBA ¼ 0:005 0; vAC 18

CHAP. 3]

CIRCUIT LAWS

35

Fig. 3-23

3.22

In the circuit Fig. 3-23, vs1 ¼ 0, vs2 ¼ 6 V, is1 ¼ 6 A, is2 ¼ 12 A. For the four cases of (a) R ¼ 0, (b) R ¼ 6 , (c) R ¼ 9 , and (d) R ¼ 10 000 , draw the simpliﬁed circuit and ﬁnd iBA and vAC .

Ans:

3.23

8 ðaÞ > > > < ðbÞ > ðcÞ > > : ðdÞ

iBA iBA iBA iBA

¼ 5:33; vAC ¼ 34 ¼ 3:2; vAC ¼ 27:6 ¼ 2:66; vAC ¼ 26 ¼ 0:005 0; vAC ¼ 18:01 18

(All in A and V)

In the circuit of Fig. 3-24, (a) ﬁnd the resistance seen by the voltage source, Rin ¼ v=i, as a function of a, and (b) evaluate Rin for a ¼ 0; 1; 2. Ans. (a) Rin ¼ R=ð1 aÞ; (b) R; 1; R

Fig. 3-24

3.24

In the circuit of Fig. 3-24, (a) ﬁnd power P delivered by the voltage source as a function of a, and (b) evaluate P for a ¼ 0; 1; 2. Ans. (a) P ¼ v2 ð1 aÞ=R; (b) v2 =R; 0; v2 =R

3.25

In the circuit of Fig. 3-24, let a ¼ 2. Connect a resistor Rx in parallel with the voltage source and adjust it within the range 0 Rx 0:99R such that the voltage source delivers minimum power. Find (a) the value of Rx and (b) the power delivered by the voltage source. Ans. (a) Rx ¼ 0:99R, (b) P ¼ v2 =ð99RÞ

Fig. 3-25

36

CIRCUIT LAWS

[CHAP. 3

3.26

In the circuit of Fig. 3-25, R1 ¼ 0 and b ¼ 100. 10 k . Ans. v ¼ 1; 10 V

Draw the simpliﬁed circuit and ﬁnd v for R ¼ 1 k and

3.27

In the circuit of Fig. 3-25, R1 ¼ 0 and R ¼ 1 k . Draw the simpliﬁed circuit and ﬁnd v for b ¼ 50; 100; 200. Note that v changes proportionally with b. Ans. v ¼ 0:5; 1; 2 V

3.28

In the circuit of Fig. 3-25, R1 ¼ 100 and R ¼ 11 k . Draw the simpliﬁed circuit and ﬁnd v for b ¼ 50; 100; 200. Compare with corresponding values obtained in Problem 3.27 and note that in the present case v is less sensitive to variations in b. Ans. v ¼ 0:90; 1; 1:04 V

3.29

A nonlinear element is modeled by the following terminal characteristic. 10v when v 0 i¼ 0:1v when v 0 Find the element’s current if it is connected to a voltage source with (a) v ¼ 1 þ sin t and (b) v ¼ 1 þ sin t. See Fig. 3-26(a). Ans. (a) i ¼ 10ð1 þ sin tÞ; (b) i ¼ 0:1ð1 þ sin tÞ

Fig. 3-26

3.30

Place a 1- linear resistor between the nonlinear element of Problem 3.29 and the voltage source. See Fig. 3-26(b). Find the element’s current if the voltage source is (a) v ¼ 1 þ sin t and (b) v ¼ 1 þ sin t. Ans. (a) i ¼ 0:91ð1 þ sin tÞ; (b) i ¼ 0:091ð1 þ sin tÞ

Analysis Methods 4.1

THE BRANCH CURRENT METHOD

In the branch current method a current is assigned to each branch in an active network. Then Kirchhoﬀ’s current law is applied at the principal nodes and the voltages between the nodes employed to relate the currents. This produces a set of simultaneous equations which can be solved to obtain the currents. EXAMPLE 4.1 Obtain the current in each branch of the network shown in Fig. 4-1 using the branch current method.

Fig. 4-1 Currents I1 ; I2 , and I3 are assigned to the branches as shown. Applying KCL at node a, I1 ¼ I2 þ I3

ð1Þ

The voltage Vab can be written in terms of the elements in each of the branches; Vab ¼ 20 I1 ð5Þ, Vab ¼ I3 ð10Þ and Vab ¼ I2 ð2Þ þ 8. Then the following equations can be written 20 I1 ð5Þ ¼ I3 ð10Þ

ð2Þ

20 I1 ð5Þ ¼ I2 ð2Þ þ 8

ð3Þ

Solving the three equations (1), (2), and (3) simultaneously gives I1 ¼ 2 A, I2 ¼ 1 A, and I3 ¼ 1 A.

Other directions may be chosen for the branch currents and the answers will simply include the appropriate sign. In a more complex network, the branch current method is diﬃcult to apply because it does not suggest either a starting point or a logical progression through the network to produce the necessary equations. It also results in more independent equations than either the mesh current or node voltage method requires. 37 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

38

4.2

ANALYSIS METHODS

[CHAP. 4

THE MESH CURRENT METHOD

In the mesh current method a current is assigned to each window of the network such that the currents complete a closed loop. They are sometimes referred to as loop currents. Each element and branch therefore will have an independent current. When a branch has two of the mesh currents, the actual current is given by their algebraic sum. The assigned mesh currents may have either clockwise or counterclockwise directions, although at the outset it is wise to assign to all of the mesh currents a clockwise direction. Once the currents are assigned, Kirchhoﬀ’s voltage law is written for each loop to obtain the necessary simultaneous equations. EXAMPLE 4.2 Obtain the current in each branch of the network shown in Fig. 4-2 (same as Fig. 4-1) using the mesh current method.

Fig. 4-2 The currents I1 and I2 are chosen as shown on the circuit diagram. starting at point ,

Applying KVL around the left loop,

20 þ 5I1 þ 10ðI1 I2 Þ ¼ 0 and around the right loop, starting at point , 8 þ 10ðI2 I1 Þ þ 2I2 ¼ 0 Rearranging terms, 15I1 10I2 ¼ 20 10I1 þ 12I2 ¼ 8

ð4Þ ð5Þ

Solving (4) and (5) simultaneously results in I1 ¼ 2 A and I2 ¼ 1 A. The current in the center branch, shown dotted, is I1 I2 ¼ 1 A. In Example 4.1 this was branch current I3 .

The currents do not have to be restricted to the windows in order to result in a valid set of simultaneous equations, although that is the usual case with the mesh current method. For example, see Problem 4.6, where each of the currents passes through the source. In that problem they are called loop currents. The applicable rule is that each element in the network must have a current or a combination of currents and no two elements in diﬀerent branches can be assigned the same current or the same combination of currents.

4.3

MATRICES AND DETERMINANTS

The n simultaneous equations of an n-mesh network can be written in matrix form. (Refer to Appendix B for an introduction to matrices and determinants.) EXAMPLE 4.3 When KVL is applied to the three-mesh network of Fig. 4-3, the following three equations are obtained:

CHAP. 4]

39

ANALYSIS METHODS

ðRA þ RB ÞI1

R B I2

¼ Va

RB I1 þ ðRB þ RC þ RD ÞI2 R D I3 ¼ 0 RD I2 þ ðRD þ RE ÞI3 ¼ Vb Placing the equations in matrix form, 2 RA þ RB 4 RB 0

RB RB þ RC þ RD RD

32 3 2 3 0 Va I1 RD 54 I2 5 ¼ 4 0 5 Vb RD þ RE I3

Fig. 4-3 The elements of the matrices can be indicated 2 R11 4 R21 R31

in general form as follows: 32 3 2 3 V1 R12 R13 I1 R22 R23 54 I2 5 ¼ 4 V2 5 R32 R33 I3 V3

ð6Þ

Now element R11 (row 1, column 1) is the sum of all resistances through which mesh current I1 passes. In Fig. 4-3, this is RA þ RB . Similarly, elements R22 and R33 are the sums of all resistances through which I2 and I3 , respectively, pass. Element R12 (row 1, column 2) is the sum of all resistances through which mesh currents I1 and I2 pass. The sign of R12 is þ if the two currents are in the same direction through each resistance, and if they are in opposite directions. In Fig. 4-3, RB is the only resistance common to I1 and I2 ; and the current directions are opposite in RB , so that the sign is negative. Similarly, elements R21 , R23 , R13 , and R31 are the sums of the resistances common to the two mesh currents indicated by the subscripts, with the signs determined as described previously for R12 . It should be noted that for all i and j, Rij ¼ Rji . As a result, the resistance matrix is symmetric about the principal diagonal. The current matrix requires no explanation, since the elements are in a single column with subscripts 1, 2, 3, . . . to identify the current with the corresponding mesh. These are the unknowns in the mesh current method of network analysis. Element V1 in the voltage matrix is the sum of all source voltages driving mesh current I1 . A voltage is counted positive in the sum if I1 passes from the to the þ terminal of the source; otherwise, it is counted negative. In other words, a voltage is positive if the source drives in the direction of the mesh current. In Fig. 4.3, mesh 1 has a source Va driving in the direction of I1 ; mesh 2 has no source; and mesh 3 has a source Vb driving opposite to the direction of I3 , making V3 negative.

The matrix equation arising from the mesh current method may be solved by various techniques. One of these, the method of determinants (Cramer’s rule), will be presented here. It should be stated, however, that other techniques are far more eﬃcient for large networks. EXAMPLE 4.4 Solve matrix equation (6) of Example 4.3 by the method of determinants. The unknown current I1 is obtained as the ratio of two determinants. The denominator determinant has the elements of resistance matrix. This may be referred to as the determinant of the coeﬃcients and given the symbol R . The numerator determinant has the same elements as R except in the ﬁrst column, where the elements of the voltage matrix replace those of the determinant of the coeﬃcients. Thus, V1 R12 R13 , R11 R12 R13 V R12 R13 1 1 I1 ¼ V2 R22 R23 R21 R22 R23 V2 R22 R23 V3 R32 R33 R31 R32 R33 R V3 R32 R33

40

ANALYSIS METHODS

[CHAP. 4

Similarly, R 1 11 R I2 ¼ R 21 R31

V1 V2 V3

R13 R23 R33

R 1 11 I3 ¼ R R 21 R31

R12 R22 R32

V1 V2 V3

An expansion of the numerator determinants by cofactors of the voltage terms results in a set of equations which can be helpful in understanding the network, particularly in terms of its driving-point and transfer resistances: 11 21 31 I1 ¼ V1 þ V2 þ V3 ð7Þ R R R 12 22 32 þ V2 þ V3 ð8Þ I2 ¼ V1 R R R 13 23 33 þ V2 þ V3 ð9Þ I3 ¼ V1 R R R Here, ij stands for the cofactor of Rij (the element in row i, column j) in R . signs of the cofactors—see Appendix B.

4.4

Care must be taken with the

THE NODE VOLTAGE METHOD

The network shown in Fig. 4-4(a) contains ﬁve nodes, where 4 and 5 are simple nodes and 1, 2, and 3 are principal nodes. In the node voltage method, one of the principal nodes is selected as the reference and equations based on KCL are written at the other principal nodes. At each of these other principal nodes, a voltage is assigned, where it is understood that this is a voltage with respect to the reference node. These voltages are the unknowns and, when determined by a suitable method, result in the network solution.

Fig. 4-4

The network is redrawn in Fig. 4-4(b) and node 3 selected as the reference for voltages V1 and V2 . KCL requires that the total current out of node 1 be zero: V1 Va V1 V1 V2 þ þ ¼0 RA RB RC Similarly, the total current out of node 2 must be zero: V2 V1 V2 V2 Vb þ þ ¼0 RC RD RE (Applying KCL in this form does not imply that the actual branch currents all are directed out of either node. Indeed, the current in branch 1–2 is necessarily directed out of one node and into the other.) Putting the two equations for V1 and V2 in matrix form,

CHAP. 4]

ANALYSIS METHODS

2

1 1 1 þ þ 6 RA RB RC 6 4 1 RC

41

32 3 2 3 1 Va =RA V1 76 7 6 7 RC 76 7 ¼ 6 7 5 1 1 1 54 5 4 þ þ V2 Vb =RE RC RD RE

Note the symmetry of the coeﬃcient matrix. The 1,1-element contains the sum of the reciprocals of all resistances connected to note 1; the 2,2-element contains the sum of the reciprocals of all resistances connected to node 2. The 1,2- and 2,1-elements are each equal to the negative of the sum of the reciprocals of the resistances of all branches joining nodes 1 and 2. (There is just one such branch in the present circuit.) On the right-hand side, the current matrix contains Va =RA and Vb =RE , the driving currents. Both these terms are taken positive because they both drive a current into a node. Further discussion of the elements in the matrix representation of the node voltage equations is given in Chapter 9, where the networks are treated in the sinusoidal steady state. EXAMPLE 4.5 Solve the circuit of Example 4.2 using the node voltage method. The circuit is redrawn in Fig. 4-5. With two principal nodes, only one equation is required. currents are all directed out of the upper node and the bottom node is the reference,

Assuming the

V1 20 V1 V1 8 þ ¼0 þ 5 2 10 from which V1 ¼ 10 V. Then, I1 ¼ ð10 20Þ=5 ¼ 2 A (the negative sign indicates that current I1 ﬂows into node 1); I2 ¼ ð10 8Þ=2 ¼ 1 A; I3 ¼ 10=10 ¼ 1 A. Current I3 in Example 4.2 is shown dotted.

Fig. 4-5

4.5

INPUT AND OUTPUT RESISTANCES

In single-source networks, the input or driving-point resistance is often of interest. Such a network is suggested in Fig. 4-6, where the driving voltage has been designated as V1 and the corresponding current as I1 . Since the only source is V1 , the equation for I1 is [see (7) of Example 4.4]: 11 I1 ¼ V1 R The input resistance is the ratio of V1 to I1 : Rinput;1 ¼

R 11

The reader should verify that R =11 actually carries the units . A voltage source applied to a passive network results in voltages between all nodes of the network. An external resistor connected between two nodes will draw current from the network and in general will reduce the voltage between those nodes. This is due to the voltage across the output resistance (see

42

ANALYSIS METHODS

[CHAP. 4

Fig. 4-6 Fig. 4-7

The´venin too). The output resistance is found by dividing the open-circuited voltage to the shortcircuited current at the desired node. The short-circuited current is found in Section 4.6.

4.6

TRANSFER RESISTANCE

A driving voltage in one part of a network results in currents in all the network branches. For example, a voltage source applied to a passive network results in an output current in that part of the network where a load resistance has been connected. In such a case the network has an overall transfer resistance. Consider the passive network suggested in Fig. 4-7, where the voltage source has been designated as Vr and the output current as Is . The mesh current equation for Is contains only one term, the one resulting from Vr in the numerator determinant: rs Is ¼ ð0Þ 1s þ þ 0 þ Vr þ 0 þ R R The network transfer resistance is the ratio of Vr to Is : Rtransfer;rs ¼

R rs

Because the resistance matrix is symmetric, rs ¼ sr , and so Rtransfer;rs ¼ Rtransfer;sr This expresses an important property of linear networks: If a certain voltage in mesh r gives rise to a certain current in mesh s, then the same voltage in mesh s produces the same current in mesh r. Consider now the more general situation of an n-mesh network containing a number of voltage sources. The solution for the current in mesh k can be rewritten in terms of input and transfer resistances [refer to (7), (8), and (9) of Example 4.4]: Ik ¼

V1 Vk1 Vk Vkþ1 Vn þ þ þ þ þ þ Rtransfer;1k Rtransfer;ðk1Þk Rinput;k Rtransfer;ðkþ1Þk Rtransfer;nk

There is nothing new here mathematically, but in this form the current equation does illustrate the superposition principle very clearly, showing how the resistances control the eﬀects which the voltage sources have on a particular mesh current. A source far removed from mesh k will have a high transfer resistance into that mesh and will therefore contribute very little to Ik . Source Vk , and others in meshes adjacent to mesh k, will provide the greater part of Ik .

4.7

NETWORK REDUCTION

The mesh current and node voltage methods are the principal techniques of circuit analysis. However, the equivalent resistance of series and parallel branches (Sections 3.4 and 3.5), combined with the voltage and current division rules, provide another method of analyzing a network. This method is tedious and usually requires the drawing of several additional circuits. Even so, the process of reducing

CHAP. 4]

43

ANALYSIS METHODS

the network provides a very clear picture of the overall functioning of the network in terms of voltages, currents, and power. The reduction begins with a scan of the network to pick out series and parallel combinations of resistors. EXAMPLE 4.6 Obtain the total power supplied by the 60-V source and the power absorbed in each resistor in the network of Fig. 4-8. Rab ¼ 7 þ 5 ¼ 12 ð12Þð6Þ Rcd ¼ ¼ 4 12 þ 6

Fig. 4-8 These two equivalents are in parallel (Fig. 4-9), giving Ref ¼

ð4Þð12Þ ¼ 3 4 þ 12

Then this 3- equivalent is in series with the 7- resistor (Fig. 4-10), so that for the entire circuit, Req ¼ 7 þ 3 ¼ 10

Fig. 4-9

Fig. 4-10

The total power absorbed, which equals the total power supplied by the source, can now be calculated as PT ¼

V2 ð60Þ2 ¼ 360 W ¼ Req 10

This power is divided between Rge and Ref as follows: Pge ¼ P7 ¼

7 ð360Þ ¼ 252 W 7þ3

Pef ¼

3 ð360Þ ¼ 108 W 7þ3

Power Pef is further divided between Rcd and Rab as follows: Pcd ¼

12 ð108Þ ¼ 81 W 4 þ 12

Pab ¼

4 ð108Þ ¼ 27 W 4 þ 12

44

ANALYSIS METHODS

[CHAP. 4

Finally, these powers are divided between the individual resistances as follows: 6 ð81Þ ¼ 27 W 12 þ 6 12 ð81Þ ¼ 54 W ¼ 12 þ 6

P12 ¼ P6

4.8

7 ð27Þ ¼ 15:75 W 7þ5 5 ð27Þ ¼ 11:25 W ¼ 7þ5

P7 ¼ P5

SUPERPOSITION

A linear network which contains two or more independent sources can be analyzed to obtain the various voltages and branch currents by allowing the sources to act one at a time, then superposing the results. This principle applies because of the linear relationship between current and voltage. With dependent sources, superposition can be used only when the control functions are external to the network containing the sources, so that the controls are unchanged as the sources act one at a time. Voltage sources to be suppressed while a single source acts are replaced by short circuits; current sources are replaced by open circuits. Superposition cannot be directly applied to the computation of power, because power in an element is proportional to the square of the current or the square of the voltage, which is nonlinear. As a further illustration of superposition consider equation (7) of Example 4.4: 11 21 31 þ V2 þ V3 I1 ¼ V 1 R R R which contains the superposition principle implicitly. Note that the three terms on the right are added to result in current I1 . If there are sources in each of the three meshes, then each term contributes to the current I1 . Additionally, if only mesh 3 contains a source, V1 and V2 will be zero and I1 is fully determined by the third term. EXAMPLE 4.7 Compute the current in the 23- resistor of Fig. 4-11(a) by applying the superposition principle. With the 200-V source acting alone, the 20-A current source is replaced by an open circuit, Fig. 4-11(b).

Fig. 4-11

CHAP. 4]

ANALYSIS METHODS

Req ¼ 47 þ

45

ð27Þð4 þ 23Þ ¼ 60:5 54

200 ¼ 3:31 A 60:5 27 ð3:31Þ ¼ 1:65 A ¼ 54

IT ¼ 0 I23

When the 20-A source acts alone, the 200-V source is replaced by a short circuit, Fig. 4-11(c). resistance to the left of the source is

The equivalent

ð27Þð47Þ ¼ 21:15 Req ¼ 4 þ 74 21:15 00 ð20Þ ¼ 9:58 A ¼ I23 21:15 þ 23

Then The total current in the 23- resistor is

0 00 I23 ¼ I23 þ I23 ¼ 11:23 A

4.9

THE´VENIN’S AND NORTON’S THEOREMS

A linear, active, resistive network which contains one or more voltage or current sources can be replaced by a single voltage source and a series resistance (The´venin’s theorem), or by a single current source and a parallel resistance (Norton’s theorem). The voltage is called the The´venin equivalent voltage, V 0 , and the current the Norton equivalent current, I 0 . The two resistances are the same, R 0 . When terminals ab in Fig. 4-12(a) are open-circuited, a voltage will appear between them.

Fig. 4-12

From Fig. 4-12(b) it is evident that this must be the voltage V 0 of the The´venin equivalent circuit. If a short circuit is applied to the terminals, as suggested by the dashed line in Fig. 4-12(a), a current will result. From Fig. 4-12(c) it is evident that this current must be I 0 of the Norton equivalent circuit. Now, if the circuits in (b) and (c) are equivalents of the same active network, they are equivalent to each other. It follows that I 0 ¼ V 0 =R 0 . If both V 0 and I 0 have been determined from the active network, then R 0 ¼ V 0 =I 0 . EXAMPLE 4.8 Obtain the The´venin and Norton equivalent circuits for the active network in Fig. 4-13(a). With terminals ab open, the two sources drive a clockwise current through the 3- and 6- resistors [Fig. 4-13(b)]. I¼

20 þ 10 30 ¼ A 3þ6 9

Since no current passes through the upper right 3- resistor, the The´venin voltage can be taken from either active branch:

46

ANALYSIS METHODS

[CHAP. 4

Fig. 4-13 30 ð3Þ ¼ 10 V 9 30 6 10 ¼ 10 V ¼ V0 ¼ 9

Vab ¼ V 0 ¼ 20 or

Vab

The resistance R 0 can be obtained by shorting out the voltage sources [Fig. 4.13(c)] and ﬁnding the equivalent resistance of this network at terminals ab: R0 ¼ 3 þ

ð3Þð6Þ ¼ 5 9

When a short circuit is applied to the terminals, current Is:c: results from the two sources. runs through the short from a to b, we have, by superposition, 2 3 2 3 6 20 3 10 6 6 7 7 Is:c: ¼ I 0 ¼ 4 5 4 5 ¼ 2A ð3Þð6Þ ð3Þð3Þ 6þ3 3þ3 3þ 6þ 9 6

Assuming that it

Figure 4-14 shows the two equivalent circuits. In the present case, V 0 , R 0 , and I 0 were obtained independently. Since they are related by Ohm’s law, any two may be used to obtain the third.

Fig. 4-14

The usefulness of The´venin and Norton equivalent circuits is clear when an active network is to be examined under a number of load conditions, each represented by a resistor. This is suggested in

CHAP. 4]

47

ANALYSIS METHODS

Fig. 4-15, where it is evident that the resistors R1 ; R2 ; . . . ; Rn can be connected one at a time, and the resulting current and power readily obtained. If this were attempted in the original circuit using, for example, network reduction, the task would be very tedious and time-consuming.

Fig. 4-15

4.10

MAXIMUM POWER TRANSFER THEOREM

At times it is desired to obtain the maximum power transfer from an active network to an external load resistor RL . Assuming that the network is linear, it can be reduced to an equivalent circuit as in Fig. 4-16. Then I¼

V0 R 0 þ RL

and so the power absorbed by the load is V 02 RL V 02 PL ¼ 0 ¼ 2 4R 0 ðR þ RL Þ

"

R 0 RL 1 R 0 þ RL

2 #

It is seen that PL attains its maximum value, V 02 =4R 0 , when RL ¼ R 0 , in which case the power in R 0 is also V 02 =4R 0 . Consequently, when the power transferred is a maximum, the eﬃciency is 50 percent.

Fig. 4-16

It is noted that the condition for maximum power transfer to the load is not the same as the condition for maximum power delivered by the source. The latter happens when RL ¼ 0, in which case power delivered to the load is zero (i.e., at a minimum).

Solved Problems 4.1

Use branch currents in the network shown in Fig. 4-17 to ﬁnd the current supplied by the 60-V source.

48

ANALYSIS METHODS

[CHAP. 4

Fig. 4-17 KVL and KCL give: I2 ð12Þ ¼ I3 ð6Þ I2 ð12Þ ¼ I4 ð12Þ

ð10Þ ð11Þ

60 ¼ I1 ð7Þ þ I2 ð12Þ I1 ¼ I2 þ I3 þ I4

ð12Þ ð13Þ

I1 ¼ I2 þ 2I2 þ I2 ¼ 4I2

ð14Þ

Substituting (10) and (11) in (13),

Now (14) is substituted in (12): 60 ¼ I1 ð7Þ þ 14 I1 ð12Þ ¼ 10I1

4.2

or

I1 ¼ 6 A

Solve Problem 4.1 by the mesh current method.

Fig. 4-18 Applying KVL to each mesh (see Fig. 4-18) results in 60 ¼ 7I1 þ 12ðI1 I2 Þ 0 ¼ 12ðI2 I1 Þ þ 6ðI2 I3 Þ 0 ¼ 6ðI3 I2 Þ þ 12I3 Rearranging terms and putting the equations in matrix form, ¼ 60 19I1 12I2 12I1 þ 18I2 6I3 ¼ 0 6I2 þ 18I3 ¼ 0

2 or

19 12 4 12 18 0 6

32 3 2 3 0 60 I1 6 54 I2 5 ¼ 4 0 5 18 I3 0

Using Cramer’s rule to ﬁnd I1 , 60 12 0 19 I1 ¼ 0 18 6 12 0 6 18 0

12 0 18 6 ¼ 17 280 2880 ¼ 6 A 6 18

CHAP. 4]

4.3

49

ANALYSIS METHODS

Solve the network of Problems 4.1 and 4.2 by the node voltage method.

See Fig. 4-19.

With two principal nodes, only one equation is necessary. V1 60 V1 V1 V1 þ þ ¼0 þ 12 6 12 7 from which V1 ¼ 18 V.

Then, I1 ¼

60 V1 ¼ 6A 7

Fig. 4-19

4.4

In Problem 4.2, obtain Rinput;1 and use it to calculate I1 . Rinput;1 ¼

Then

4.5

R 2880 2880 ¼ ¼ 10 ¼ 288 11 18 6 6 18 I1 ¼

60 60 ¼ 6A ¼ Rinput;1 10

Obtain Rtransfer;12 and Rtransfer;13 for the network of Problem 4.2 and use them to calculate I2 and I3 . The cofactor of the 1,2-element in R must include a negative sign: 12 6 ¼ 216 12 ¼ ð1Þ1þ2 0 18

Rtransfer;12 ¼

R 2880 ¼ 13:33 ¼ 216 12

Then, I2 ¼ 60=13:33 ¼ 4:50 A: 12 18 ¼ 72 13 ¼ ð1Þ1þ3 0 6

Rtransfer;13 ¼

R 2880 ¼ ¼ 40 13 72

Then, I3 ¼ 60=40 ¼ 1:50 A:

4.6

Solve Problem 4.1 by use of the loop currents indicated in Fig. 4-20. The elements in the matrix form of the equations are obtained by inspection, following the rules of Section 4.2.

50

ANALYSIS METHODS

[CHAP. 4

Fig. 4-20 32 3 2 3 I1 60 7 7 13 7 54 I2 5 ¼ 4 60 5 60 I3 7 19 2 3 19 7 7 6 7 R ¼ 4 7 13 7 5 ¼ 2880 7 7 19

2

19 4 7 7 Thus,

Notice that in Problem 4.2, too, R ¼ 2880, although the elements in the determinant were diﬀerent. All valid sets of meshes or loops yield the same numerical value for R . The three numerator determinants are 60 7 7 N2 ¼ 8642 7 ¼ 4320 N3 ¼ 4320 N1 ¼ 60 13 60 7 19 Consequently, I1 ¼

N1 4320 ¼ 1:5 A ¼ R 2880

I2 ¼

N2 ¼ 3A R

I3 ¼

N3 ¼ 1:5 A R

The current supplied by the 60-V source is the sum of the three loop currents, I1 þ I2 þ I3 ¼ 6 A.

4.7

Write the mesh current matrix equation for the network of Fig. 4-21 by inspection, and solve for the currents.

Fig. 4-21 2

7 4 5 0

5 19 4

3 32 3 2 25 0 I1 4 54 I2 5 ¼ 4 25 5 I3 50 6

Solving, 25 5 0 0 7 5 I1 ¼ 25 19 4 5 19 4 ¼ ð700Þ 536 ¼ 1:31 A 50 4 6 6 0 4

CHAP. 4]

51

ANALYSIS METHODS

Similarly, I2 ¼

4.8

N2 1700 ¼ 3:17 A ¼ 536 R

I3 ¼

N3 5600 ¼ 10:45 A ¼ 536 R

Solve Problem 4.7 by the node voltage method. The circuit has been redrawn in Fig. 4-22, with two principal nodes numbered 1 and 2 and the third chosen as the reference node. By KCL, the net current out of node 1 must equal zero.

Fig. 4-22 V1 V1 25 V1 V2 þ ¼0 þ 2 10 5 Similarly, at node 2, V2 V1 V2 V2 þ 50 þ þ ¼0 10 4 2 Putting the two equations in matrix form, 2 32 3 1 1 1 1 5 V 6 2 þ 5 þ 10 76 1 7 10 6 76 7 ¼ 4 4 5 5 1 1 1 1 þ þ V2 25 10 10 4 2 The determinant of coeﬃcients and the numerator determinants are 0:80 0:10 ¼ 0:670 ¼ 0:10 0:85 5 0:10 0:80 ¼ 1:75 N1 ¼ N2 ¼ 25 0:85 0:10

5 ¼ 19:5 25

From these, V1 ¼

1:75 ¼ 2:61 V 0:670

V2 ¼

19:5 ¼ 29:1 V 0:670

In terms of these voltages, the currents in Fig. 4-21 are determined as follows: I1 ¼

4.9

V1 ¼ 1:31 A 2

I2 ¼

V1 V2 ¼ 3:17 A 10

I3 ¼

V2 þ 50 ¼ 10:45 A 2

For the network shown in Fig. 4-23, ﬁnd Vs which makes I0 ¼ 7:5 mA. The node voltage method will be used and the matrix form of the equations written by inspection.

52

ANALYSIS METHODS

Fig. 4-23 2

1 1 1 6 20 þ 7 þ 4 6 4 1 4 Solving for V2 ,

Then

32 3 2 3 1 Vs =20 V1 7 6 7 6 4 7 76 7 ¼ 6 7 5 1 1 1 54 5 4 þ þ V2 0 4 6 6

0:443 Vs =20 0:250 0 ¼ 0:0638Vs V2 ¼ 0:443 0:250 0:250 0:583 7:5 103 ¼ I0 ¼

V2 0:0638Vs ¼ 6 6

from which Vs ¼ 0:705 V.

4.10

In the network shown in Fig. 4-24, ﬁnd the current in the 10- resistor.

Fig. 4-24 The nodal equations in matrix form are written by inspection. 2

32 3 2 3 1 2 V1 6 7 6 7 5 7 76 7 ¼ 6 7 5 1 1 54 5 4 þ V2 6 5 2 2 0:20 6 0:70 ¼ 1:18 V V1 ¼ 0:30 0:20 0:20 0:70

1 1 6 5 þ 10 6 4 1 5

[CHAP. 4

CHAP. 4]

53

ANALYSIS METHODS

Then, I ¼ V1 =10 ¼ 0:118 A.

4.11

Find the voltage Vab in the network shown in Fig. 4-25.

Fig. 4-25 The two closed loops are independent, and no current can pass through the connecting branch. I1 ¼ 2 A Vab ¼ Vax þ Vxy þ Vyb

4.12

30 ¼ 3A 10 ¼ I1 ð5Þ 5 þ I2 ð4Þ ¼ 3 V I2 ¼

For the ladder network of Fig. 4-26, obtain the transfer resistance as expressed by the ratio of Vin to I4 .

Fig. 4-26 By inspection, the network equation is 2

15 6 5 6 4 0 0

5 20 5 0

32 3 2 3 I1 Vin 0 0 7 6 7 6 5 07 76 I2 7 ¼ 6 0 7 20 5 54 I3 5 4 0 5 I4 0 5 5 þ RL

R ¼ 5125RL þ 18 750

N4 ¼ 125Vin

N Vin I4 ¼ 4 ¼ ðAÞ R 41RL þ 150 and

4.13

Rtransfer;14 ¼

Vin ¼ 41RL þ 150 ðÞ I4

Obtain a The´venin equivalent for the circuit of Fig. 4-26 to the left of terminals ab. The short-circuit current Is:c: is obtained from the three-mesh circuit shown in Fig. 4-27.

54

ANALYSIS METHODS

[CHAP. 4

Fig. 4-27 2

15 5

0

32

I1

3

2

Vin

3

7 7 6 6 76 4 5 20 5 54 I2 5 ¼ 4 0 5 0 Is:c: 0 5 15 5 20 Vin 0 5 Vin Is:c: ¼ ¼ R 150 The open-circuit voltage Vo:c: is the voltage across the 5- resistor indicated in Fig. 4-28.

Fig. 4-28 2

15 5 6 4 5 20 0 5

32 3 2 3 I1 Vin 0 76 7 6 7 5 54 I2 5 ¼ 4 0 5 20 0 I3

I3 ¼

25Vin Vin ¼ ðAÞ 5125 205

Then, the The´venin source V 0 ¼ Vo:c: ¼ I3 ð5Þ ¼ Vin =41, and RTh ¼

Vo:c: 150 ¼ Is:c: 41

The The´venin equivalent circuit is shown in Fig. 4-29. current is I4 ¼

With RL connected to terminals ab, the output

Vin =41 Vin ¼ ðAÞ ð150=41Þ þ RL 41RL þ 150

agreeing with Problem 4.12.

4.14

Use superposition to ﬁnd the current I from each voltage source in the circuit shown in Fig. 4-30. Loop currents are chosen such that each source contains only one current.

CHAP. 4]

55

ANALYSIS METHODS

Fig. 4-29

Fig. 4-30

54 27 27 74

I1 I2

¼ ¼

460 200

From the 460-V source, I10 ¼ I 0 ¼

ð460Þð74Þ ¼ 10:42 A 3267

and for the 200-V source I100 ¼ I 00 ¼ Then,

ð200Þð27Þ ¼ 1:65 A 3267

I ¼ I 0 þ I 00 ¼ 10:42 þ 1:65 ¼ 8:77 A

Fig. 4-31(a)

4.15

Obtain the current in each resistor in Fig. 4-31(a), using network reduction methods. As a ﬁrst step, two-resistor parallel combinations are converted to their equivalents. For the 6 and 3 , Req ¼ ð6Þð3Þ=ð6 þ 3Þ ¼ 2 . For the two 4- resistors, Req ¼ 2 . The circuit is redrawn with series resistors added [Fig. 4-31(b)]. Now the two 6- resistors in parallel have the equivalent Req ¼ 3 , and this is in series with the 2 . Hence, RT ¼ 5 , as shown in Fig. 4-31(c). The resulting total current is

56

ANALYSIS METHODS

[CHAP. 4

Fig. 4-31 (cont.)

IT ¼

25 ¼ 5A 5

Now the branch currents can be obtained by working back through the circuits of Fig. 4-31(b) and 4-31(a) IC ¼ IF ¼ 12 IT ¼ 2:5 A ID ¼ IE ¼ 12 IC ¼ 1:25 A 3 5 I ¼ A 6þ3 T 3 6 10 IB ¼ I ¼ A 6þ3 T 3 IA ¼

4.16

Find the value of the adjustable resistance R which results in maximum power transfer across the terminals ab of the circuit shown in Fig. 4-32.

Fig. 4-32 First a The´venin equivalent is obtained, with V 0 ¼ 60 V and R 0 ¼ 11 . power transfer occurs for R ¼ R 0 ¼ 11 , with Pmax ¼

By Section 4.10, maximum

V 02 ¼ 81:82 W 4R 0

Supplementary Problems 4.17

Apply the mesh current method to the network of Fig. 4-33 and write the matrix equations by inspection. Obtain current I1 by expanding the numerator determinant about the column containing the voltage sources to show that each source supplies a current of 2.13 A.

CHAP. 4]

ANALYSIS METHODS

57

Fig. 4-33 4.18

Loop currents are shown in the network of Fig. 4-34. currents. Ans. 3.55 A, 1:98 A, 2:98 A

Write the matrix equation and solve for the three

Fig. 4-34

4.19

The network of Problem 4.18 has been redrawn in Fig. 4-35 for solution by the node voltage method. tain node voltages V1 and V2 and verify the currents obtained in Problem 4.18. Ans. 7.11 V, 3:96 V

Ob-

Fig. 4-35

4.20

In the network shown in Fig. 4-36 current I0 ¼ 7:5 mA. voltage Vs . Ans. 0.705 V

Use mesh currents to ﬁnd the required source

4.21

Use appropriate determinants of Problem 4.20 to obtain the input resistance as seen by the source voltage Ans: 23:5 Vs . Check the result by network reduction.

58

ANALYSIS METHODS

[CHAP. 4

Fig. 4-36

4.22

For the network shown in Fig. 4-36, obtain the transfer resistance which relates the current I0 to the source voltage Vs . Ans: 94:0

4.23

For the network shown in Fig. 4-37, obtain the mesh currents.

Ans. 5.0 A, 1.0 A, 0.5 A

Fig. 4-37 4.24

Using the matrices from Problem 4.23 calculate Rinput;1 , Rtransfer;12 , and Rtransfer;13 . Ans: 10 ; 50 ; 100

4.25

In the network shown in Fig. 4-38, obtain the four mesh currents. Ans. 2.11 A, 0:263 A, 2:34 A, 0.426 A

Fig. 4-38

4.26

For the circuit shown in Fig. 4-39, obtain Vo:c: , Is:c: , and R 0 at the terminals ab using mesh current or node voltage methods. Consider terminal a positive with respect to b. Ans: 6:29 V; 0:667 A; 9:44

CHAP. 4]

ANALYSIS METHODS

59

Fig. 4-39 4.27

Use the node voltage method to obtain Vo:c: and Is:c: at the terminals ab of the network shown in Fig. 440. Consider a positive with respect to b. Ans: 11:2 V; 7:37 A

Fig. 4-40 4.28

Use network reduction to obtain the current in each of the resistors in the circuit shown in Fig. 4-41. Ans. In the 2.45- resistor, 3.10 A; 6.7 , 0.855 A; 10.0 , 0.466 A; 12.0 , 0.389 A; 17.47 , 0.595 A; 6.30 , 1.65 A

Fig. 4-41 4.29

Both ammeters in the circuit shown in Fig. 4-42 indicate 1.70 A. If the source supplies 300 W to the circuit, Ans: 23:9 ; 443:0 ﬁnd R1 and R2 .

Fig. 4-42

60

4.30

ANALYSIS METHODS

[CHAP. 4

In the network shown in Fig. 4-43 the two current sources provide I 0 and I 00 where I 0 þ I 00 ¼ I. superposition to obtain these currents. Ans. 1.2 A, 15.0 A, 16.2 A

Use

Fig. 4-43

4.31

Obtain the current I in the network shown in Fig. 4.44.

Ans:

12 A

Fig. 4-44 Fig. 4-45

4.32

Obtain the The´venin and Norton equivalents for the network shown in Fig. 4.45. Ans: V 0 ¼ 30 V; I 0 ¼ 5 A; R 0 ¼ 6

4.33

Find the maximum power that the active network to the left of terminals ab can deliver to the adjustable resistor R in Fig. 4-46. Ans. 8.44 W

Fig. 4-46 4.34

Under no-load condition a dc generator has a terminal voltage of 120 V. When delivering its rated current of 40 A, the terminal voltage drops to 112 V. Find the The´venin and Norton equivalents. Ans: V 0 ¼ 120 V; I 0 ¼ 600 A; R 0 ¼ 0:2

4.35

The network of Problem 4.14 has been redrawn in Fig. 4-47 and terminals a and b added. Reduce the network to the left of terminals ab by a The´venin or Norton equivalent circuit and solve for the current I. Ans: 8:77 A

CHAP. 4]

61

ANALYSIS METHODS

Fig. 4-47 4.36

Node Voltage Method. In the circuit of Fig. 4-48 write three node equations for nodes A, B, and C, with node D as the reference, and ﬁnd the node voltages. 8 5VA 2VB 3VC ¼ 30 > < Node A: Ans: from which VA ¼ 17; VB ¼ 9; VC ¼ 12:33 all in V Node B: VA þ 6VB 3VC ¼ 0 > : Node C: VA 2VB þ 3VC ¼ 2

Fig. 4-48 4.37

In the circuit of Fig. 4-48 note that the current through the 3- resistor is 3 A giving rise to VB ¼ 9 V. Apply KVL around the mesh on the upper part of the circuit to ﬁnd current I coming out of the voltage source, then ﬁnd VA and VC . Ans: I ¼ 1=3 A; VA ¼ 17 V; VC ¼ 37=3 V

4.38

Superposition. In the circuit of Fig. 4-48 ﬁnd contribution of each source to VA , VB , VC , and show that they add up to values found in Problems 4.36 and 4.37.

Ans.

Contribution of the voltage source:

VA ¼ 3

VB ¼ 0

VC ¼ 1

Contribution of the 1 A current source:

VA ¼ 6

VB ¼ 3

VC ¼ 4

Contribution of the 2 A current source:

VA ¼ 8

VB ¼ 6

VC ¼ 28=3

Contribution of all sources:

VA ¼ 17

VB ¼ 9

VC ¼ 37=3

(All in V)

4.39

In the circuit of Fig. 4-48 remove the 2-A current source and then ﬁnd the voltage Vo:c: between the opencircuited nodes C and D. Ans: Vo:c: ¼ 3 V

4.40

Use the values for VC and Vo:c: obtained in Problems 4.36 and 4.39 to ﬁnd the The´venin equivalent of the circuit of Fig. 4-48 seen by the 2-A current source. Ans: VTh ¼ 3 V; RTh ¼ 14=3

4.41

In the circuit of Fig. 4-48 remove the 2-A current source and set the other two sources to zero, reducing the circuit to a source-free resistive circuit. Find R, the equivalent resistance seen from terminals CD, and note that the answer is equal to the The´venin resistance obtained in Problem 4.40. Ans: R ¼ 14=3

62

4.42

ANALYSIS METHODS

[CHAP. 4

Find The´venin equivalent of the circuit of Fig. 4-49 seen from terminals AB. ans: VTh ¼ 12 V; RTh ¼ 17

Fig. 4-49 Fig. 4-50

4.43

Loop Current Method. In the circuit of Fig. 4-50 write three loop equations using I1 , I2 , and I3 . the currents. 8 4I1 þ 2I2 þ I3 ¼ 3 > < Loop 1: Loop 2: 2I1 þ 5I2 I3 ¼ 2 From which I1 ¼ 32=51; I2 ¼ 9=51; I3 ¼ 7=51 all in A Ans: > : Loop 3: I1 þ 2I2 þ 2I3 ¼ 0

4.44

Superposition. In the circuit of Fig. 4-50 ﬁnd the contribution of each source to I1 , I2 , I3 , and show that they add up to values found in Problem 4.43.

Ans.

4.45

From the source on the left:

I1 ¼ 36=51

I2 ¼ 9=51

I3 ¼ 27=51

From the source on the right:

I1 ¼ 4=51

I2 ¼ 18=51

I3 ¼ 20=51

From both sources:

I1 ¼ 32=51

I2 ¼ 9=51

I3 ¼ 7=51

Then ﬁnd

(All in A)

Node Voltage Method. In the circuit of Fig. 4-51 write three node equations for nodes A, B, and C, with node D as the reference, and ﬁnd the node voltages.

Fig. 4-51

Ans:

8 > < Node A: Node B: > : Node C:

9VA 7VB

2VC ¼ 42

3VA þ 8VB 2VC ¼ 9 3VA 7VB þ 31VC ¼ 0

From which VA ¼ 9; VB ¼ 5; VC ¼ 2 all in V

CHAP. 4]

63

ANALYSIS METHODS

4.46

Loop Current Method. In the circuit of Fig. 4-51 write two loop equations using I1 and I2 as loop currents, then ﬁnd the currents and node voltages. Loop 1: 4I1 I2 ¼ 2 I1 ¼ 1 A; I2 ¼ 2 A Ans: from which, Loop 2: I1 þ 2I2 ¼ 3 VA ¼ 9 V; VB ¼ 5 V; VC ¼ 2 V

4.47

Superposition. In the circuit of Fig. 4-51 ﬁnd the contribution of each source to VA , VB , VC , and show that they add up to values found in Problem 4.45.

Ans.

4.48

From the current source:

VA ¼ 7:429

VB ¼ 3:143

VC ¼ 1:429

From the voltage source:

VA ¼ 1:571

VB ¼ 1:857

VC ¼ 0:571

From both sources:

VA ¼ 9

VB ¼ 5

VC ¼ 2

(all in V)

Verify that the circuit of Fig. 4-52(a) is equivalent to the circuit of Fig. 4-51. Ans. Move node B in Fig. 4-51 to the outside of the loop.

Fig. 4-52

4.49

Find VA and VB in the circuit of Fig. 4-52(b).

4.50

Show that the three terminal circuits enclosed in the dashed boundaries of Fig. 4-52(a) and (b) are equivalent (i.e., in terms of their relation to other circuits). Hint: Use the linearity and superposition properties, along with the results of Problems 4.48 and 4.49.

Ans:

VA ¼ 9; VB ¼ 5, both in V

Amplifiers and Operational Amplifier Circuits 5.1

AMPLIFIER MODEL

An ampliﬁer is a device which magniﬁes signals. The heart of an ampliﬁer is a source controlled by an input signal. A simpliﬁed model of a voltage ampliﬁer is shown in Fig. 5-1(a). The input and output reference terminals are often connected together and form a common reference node. When the output terminal is open we have v2 ¼ kv1 , where k, the multiplying factor, is called the open circuit gain. Resistors Ri and Ro are the input and output resistances of the ampliﬁer, respectively. For a better operation it is desired that Ri be high and Ro be low. In an ideal ampliﬁer, Ri ¼ 1 and Ro ¼ 0 as in Fig. 5-1(b). Deviations from the above conditions can reduce the overall gain.

Fig. 5-1

64 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

65

EXAMPLE 5.1 A practical voltage source vs with an internal resistance Rs is connected to the input of a voltage ampliﬁer with input resistance Ri as in Fig. 5-2. Find v2 =vs .

Fig. 5-2 The ampliﬁer’s input voltage, v1 , is obtained by dividing vs between Ri and Rs . v1 ¼

Ri v Ri þ Rs s

The output voltage v2 is v2 ¼ kv1 ¼

kRi v Ri þ Rs s

from which v2 Ri ¼ k vs Ri þ Rs The ampliﬁer loads the voltage source.

ð1Þ

The open-loop gain is reduced by the factor Ri =ðRi þ Rs Þ.

EXAMPLE 5.2 In Fig. 5-3 a practical voltage source vs with internal resistance Rs feeds a load Rl through an ampliﬁer with input and output resistances Ri and Ro , respectively. Find v2 =vs .

Fig. 5-3 By voltage division, v1 ¼

Ri v Ri þ Rs s

Similarly, the output voltage is v2 ¼ kv1

Rl Ri Rl ¼k v Rl þ Ro ðRi þ Rs ÞðRl þ Ro Þ s

or

V2 Ri Rl ¼ k vs Ri þ Rs Rl þ Ro

ð2Þ

Note that the open-loop gain is further reduced by an additional factor of Rl =ðRl þ Ro Þ, which also makes the output voltage dependent on the load.

5.2

FEEDBACK IN AMPLIFIER CIRCUITS

The gain of an ampliﬁer may be controlled by feeding back a portion of its output to its input as done for the ideal ampliﬁer in Fig. 5-4 through the feedback resistor R2 . The feedback ratio R1 =ðR1 þ R2 Þ aﬀects the overall gain and makes the ampliﬁer less sensitive to variations in k.

66

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-4

EXAMPLE 5.3 Find v2 =vs in Fig. 5-4 and express it as a function of the ratio b ¼ R1 =ðR1 þ R2 Þ. From the ampliﬁer we know that or

v2 ¼ kv1

v1 ¼ v2 =k

ð3Þ

Applying KCL at node A, v1 vs v1 v2 þ ¼0 R1 R2

ð4Þ

Substitute v1 in (3) into (4) to obtain v2 R2 k k ¼ ð1 bÞ ¼ 1 bk vs R2 þ R1 R1 k

where b ¼

R1 R1 þ R2

ð5Þ

EXAMPLE 5.4 In Fig. 5-5, R1 ¼ 1 k and R2 ¼ 5 k. (a) Find v2 =vs as a function of the open-loop gain k. (b) Compute v2 =vs for k ¼ 100 and 1000 and discuss the results.

Fig. 5-5 (a) Figures 5-4 and 5-5 diﬀer only in the polarity of the dependent voltage source. Example 5.3 and change k to k in (5). v2 k ¼ ð1 bÞ 1 þ bk vs

where b ¼

To ﬁnd v2 =vs , use the results of

R1 1 ¼ R1 þ R2 6

v2 5k ¼ vs 6 þ k (b) At k ¼ 100, v2 =vs ¼ 4:72; at k ¼ 1000, v2 =vs ¼ 4:97. Thus, a tenfold increase in k produces only a 5.3 percent change in v2 =vs ; i.e., ð4:97 4:72Þ=4:72 ¼ 5:3 percent. Note that for very large values of k, v2 =vs approaches R2 =R1 which is independent of k.

5.3

OPERATIONAL AMPLIFIERS

The operational ampliﬁer (op amp) is a device with two input terminals, labeled þ and or noninverting and inverting, respectively. The device is also connected to dc power supplies (þVcc and

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

67

Vcc ). The common reference for inputs, output, and power supplies resides outside the op amp and is called the ground (Fig. 5-6).

Fig. 5-6

The output voltage vo depends on vd ¼ vþ v . Neglecting the capacitive eﬀects, the transfer function is that shown in Fig. 5-7. In the linear range, vo ¼ Avd . The open-loop gain A is generally very high. vo saturates at the extremes of þVcc and Vcc when input vd exceeds the linear range jvd j > Vcc =A.

Fig. 5-7

Figure 5-8 shows the model of an op amp in the linear range with power supply connections omitted for simplicity. In practice, Ri is large, Ro is small, and A ranges from 105 to several millions. The model of Fig. 5-8 is valid as long as the output remains between þVcc and Vcc . Vcc is generally from 5 to 18 V. EXAMPLE 5.5 In the op amp of Fig. 5-8, Vcc ¼ 15 V, A ¼ 105 , and v ¼ 0. tude of vþ for linear operation. jvo j ¼ j105 vþ j < 15 V

Find the upper limit on the magni-

jvþ j < 15 105 V ¼ 150 mV

EXAMPLE 5.6 In the op amp of Fig. 5-8, Vcc ¼ 5 V, A ¼ 105 , v ¼ 0 and vþ ¼ 100 sin 2 t ðmVÞ. Find and sketch the open-loop output vo . The input to the op amp is vd ¼ vþ v ¼ ð100 sin 2 tÞ106 (V). When the op amp operates in the linear range, vo ¼ 105 vd ¼ 10 sin 2 t (V). The output should remain between þ5 and 5 V (Fig. 5-9). Saturation starts when vo ¼ 10 sin 2 t reaches the 5-V level. This occurs at t ¼ 1=12 s. The op amp comes out of 5-V saturation at

68

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-8 t ¼ 5=12. Similarly, the op amp is in 5-V saturation from t ¼ 7=12 to 11/12 s. in volts, from t ¼ 0 to 1 s is 8 5 1=12 < t < 5=12 < 5 7=12 < t < 11=12 vo ¼ : 10 sin 2 t otherwise

One full cycle of the output, given

Fig. 5-9 EXAMPLE 5.7 Repeat Example 5.6 for v ¼ 25 mV and vþ ¼ 50 sin 2 t ðmV). vd ¼ vþ v ¼ ð50 sin 2 tÞ106 25 106 ¼ 50 106 ðsin 2 t 1=2Þ ðVÞ When the op amp is within linear range, its output is vo ¼ 105 vd ¼ 5ðsin 2 t 1=2Þ ðVÞ vo saturates at the 5-V level when 5ðsin 2t 1=2Þ < 5, 7=12 < t < 11=12 (see Fig. 5-10). One cycle of vo , in volts, from t ¼ 0 to 1 s is

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS vo ¼

5 5ðsin 2t 1=2Þ

69

7=12 < t < 11=12 otherwise

Fig. 5-10 EXAMPLE 5.8 In Fig. 5-11, R1 ¼ 10 k, R2 ¼ 50 k, Ri ¼ 500 k, Ro ¼ 0, and A ¼ 105 . Find v2 =v1 . the ampliﬁer is not saturated.

Assume

Fig. 5-11 The sum of currents arriving at node B is zero.

Note that vA ¼ 0 and vB ¼ vd .

v1 þ vd v v þ vd þ d þ 2 ¼0 10 500 50

Therefore, ð6Þ

Since Ro ¼ 0, we have v2 ¼ Avd ¼ 105 vd

or

vd ¼ 105 v2

ð7Þ

70

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Substituting vd in (7) into (6), the ratio v2 =v1 is found to be v2 5 ¼ ¼ 5 v1 1 þ 105 þ 5 105 þ 0:1 105

5.4

ANALYSIS OF CIRCUITS CONTAINING IDEAL OP AMPS

In an ideal op amp, Ri and A are inﬁnite and Ro is zero. Therefore, the ideal op amp draws zero current at its inverting and noninverting inputs, and if it is not saturated these inputs are at the same voltage. Throughout this chapter we assume op amps are ideal and operate in the linear range unless speciﬁed otherwise. EXAMPLE 5.9 The op amp in Fig. 5-12 is ideal and not saturated. Find (a) v2 =v1 ; (b) the input resistance v1 =i1 ; and (c) i1 ; i2 ; p1 (the power delivered by v1 ), and p2 (the power dissipated in the resistors) given v1 ¼ 0:5 V.

Fig. 5-12 (a) The noninverting terminal A is grounded and so vA ¼ 0. Since the op amp is ideal and not saturated, vB ¼ 0. Applying KCL at nodes B and C and noting that the op amp draws no current, we get Node B:

v1 vC þ ¼0 5 10

or

vC ¼ 2v1

(8)

Node C:

vC vC vC v2 þ þ ¼0 10 1 2

or

v2 ¼ 3:2vC

(9)

Substituting vC in (8) into (9), or

v2 ¼ 6:4v1

v2 =v1 ¼ 6:4

(b) With VB ¼ 0, i1 ¼ v1 =5000 and so input resistance ¼ v1 =i1 ¼ 5 k (c)

The input current is i1 ¼ v1 =5000. Given that v1 ¼ 0:5 V, i1 ¼ 0:5=5000 ¼ 0:1 mA. To ﬁnd i2 , we apply KCL at the output of the op amp; i2 ¼ From part (a), v2 ¼ 3:2 V and vC ¼ 1 V. The power delivered by v1 is

v2 v vC þ 2 8000 2000

Therefore, i2 ¼ 1:5 mA.

p1 ¼ v1 i1 ¼ v21 =5000 ¼ 50 106 W ¼ 50 mW Powers in the resistors are

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

1 k:

p1 k ¼ v2C =1000 ¼ 0:001 W ¼ 1000 mW

2 k:

p2 k ¼ ðv2 vC Þ2 =2000 ¼ 0:00242 W ¼ 2420 mW

5 k:

p5 k ¼ v21 =5000 ¼ 0:00005 W ¼ 50 mW

8 k:

p8 k ¼ v22 =8000 ¼ 0:00128 W ¼ 1280 mW

10 k:

p10 k ¼ v2C =10 000 ¼ 0:0001 W ¼ 100 mW

71

The total power dissipated in the resistors is p2 ¼ p1 k þ p2 k þ p5 k þ p8 k þ p10 k ¼ 1000 þ 2420 þ 50 þ 1280 þ 100 ¼ 4850 mW

5.5

INVERTING CIRCUIT

In an inverting circuit, the input signal is connected through R1 to the inverting terminal of the op amp and the output terminal is connected back through a feedback resistor R2 to the inverting terminal. The noninverting terminal of the op amp is grounded (see Fig. 5-13).

Fig. 5-13

To ﬁnd the gain v2 =v1 , apply KCL to the currents arriving at node B: v1 v þ 2 ¼0 R1 R2

and

v2 R ¼ 2 v1 R1

The gain is negative and is determined by the choice of resistors only. is R1 .

5.6

ð10Þ The input resistance of the circuit

SUMMING CIRCUIT

The weighted sum of several voltages in a circuit can be obtained by using the circuit of Fig. 5-14. This circuit, called a summing circuit, is an extension of the inverting circuit. To ﬁnd the output, apply KCL to the inverting node: v1 v v v þ 2 þ þ n þ o ¼ 0 R1 R2 Rn Rf from which vo ¼

Rf Rf Rf v1 þ v2 þ þ vn R1 R2 Rn

ð11Þ

EXAMPLE 5.10 Let the circuit of Fig. 5-14 have four input lines with R1 ¼ 1; R2 ¼ 12 ; R3 ¼ 14 ; R4 ¼ 18, and Rf ¼ 1, all values given in k. The input lines are set either at 0 or 1 V. Find vo in terms of v4 , v3 , v2 , v1 , given the following sets of inputs: (a) v4 ¼ 1 V

v3 ¼ 0

v2 ¼ 0

v1 ¼ 1 V

72

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-14 (b) v4 ¼ 1 V

v3 ¼ 1 V

v2 ¼ 1 V

v1 ¼ 0

From (11) vo ¼ ð8v4 þ 4v3 þ 2v2 þ v1 Þ Substituting for v1 to v4 we obtain ðaÞ ðbÞ

vo ¼ 9 V vo ¼ 14 V

The set fv4 ; v3 ; v2 ; v1 g forms a binary sequence containing four bits at high (1 V) or low (0 V) values. Input sets given in (a) and (b) correspond to the binary numbers ð1001Þ2 ¼ ð9Þ10 and ð1110Þ2 ¼ ð14Þ10 , respectively. With the inputs at 0 V (low) or 1 V (high), the circuit converts the binary number represented by the input set fv4 ; v3 ; v2 ; v1 g to a negative voltage which, when measured in V, is equal to the base 10 representation of the input set. The circuit is a digital-to-analog converter.

5.7

NONINVERTING CIRCUIT

In a noninverting circuit the input signal arrives at the noninverting terminal of the op amp. The inverting terminal is connected to the output through R2 and also to the ground through R1 (see Fig. 5-15).

Fig. 5-15

To ﬁnd the gain v2 =v1 , apply KCL at node B. op amp draws no current. v1 v1 v2 þ ¼0 R1 R2

Note that terminals A and B are both at v1 and the

or

v2 R ¼1þ 2 v1 R1

ð12Þ

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

73

The gain v2 =v1 is positive and greater than or equal to one. The input resistance of the circuit is inﬁnite as the op amp draws no current. EXAMPLE 5.11

Find v2 =v1 in the circuit shown in Fig. 5-16.

Fig. 5-16 First ﬁnd vA by dividing v1 between the 10-k and 5-k resistors. vA ¼

5 1 v ¼ v 5 þ 10 1 3 1

From (12) we get 7 9 9 1 v1 ¼ 1:5v1 v2 ¼ 1 þ vA ¼ vA ¼ 2 2 2 3

and

v2 ¼ 1:5 v1

Another Method Find vB by dividing v2 between the 2-k and 7-k resistors and set vB ¼ vA . vB ¼

EXAMPLE 5.12

2 2 1 v ¼ v ¼ v 2þ7 2 9 2 3 1

and

v2 ¼ 1:5 v1

Determine vo in Fig. 5-17 in terms of v1 ; v2 ; v3 ; and the circuit elements.

Fig. 5-17 First, vA is found by applying KCL at node A. v1 vA v2 vA v3 vA þ þ ¼0 R R R

or

1 vA ¼ ðv1 þ v2 þ v3 Þ 3

ð13Þ

From (12) and (13) we get R 1 R 1 þ 2 ðv1 þ v2 þ v3 Þ vo ¼ 1 þ 2 vA ¼ 3 R1 R1

ð14Þ

74

5.8

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

VOLTAGE FOLLOWER

The op amp in the circuit of Fig. 5-18(a) provides a unity gain ampliﬁer in which v2 ¼ v1 since v1 ¼ vþ , v2 ¼ v and vþ ¼ v . The output v2 follows the input v1 . By supplying il to Rl , the op amp eliminates the loading eﬀect of Rl on the voltage source. It therefore functions as a buﬀer. EXAMPLE 5.13 (a) Find is ; vl ; v2 ; and il in Fig. 5-18(a). (b) Compare these results with those obtained when source and load are connected directly as in Fig. 5-18(b). (a) With the op amp present [Fig. 5-18(a)], we have is ¼ 0

v1 ¼ vs

v2 ¼ v1 ¼ vs

il ¼ vs =Rl

The voltage follower op amp does not draw any current from the signal source vs . Therefore, vs reaches the load with no reduction caused by the load current. The current in Rl is supplied by the op amp. (b) With the op amp removed [Fig. 5-18(b)], we have is ¼ il ¼

vs Rl þ Rs

and

v1 ¼ v2 ¼

Rl v Rl þ Rs s

The current drawn by Rl goes through Rs and produces a drop in the voltage reaching it. depends on Rl .

Fig. 5-18

The load voltage v2

CHAP. 5]

5.9

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

75

DIFFERENTIAL AND DIFFERENCE AMPLIFIERS

A signal source vf with no connection to ground is called a ﬂoating source. ampliﬁed by the circuit of Fig. 5-19.

Such a signal may be

Fig. 5-19

Here the two input terminals A and B of the op amp are at the same voltage. KVL around the input loop we get vf ¼ 2R1 i

or

Therefore, by writing

i ¼ vf =2R1

The op amp inputs do not draw any current and so current i also ﬂows through the R2 resistors. Applying KVL around the op amp, we have vo þ R2 i þ R2 i ¼ 0

vo ¼ 2R2 i ¼ 2R2 vf =2R1 ¼ ðR2 =R1 Þvf

ð15Þ

In the special case when two voltage sources v1 and v2 with a common ground are connected to the inverting and noninverting inputs of the circuit, respectively (see Fig. 5-20), we have vf ¼ v1 v2 and vo ¼ ðR2 =R1 Þðv2 v1 Þ EXAMPLE 5.14 Find vo as a function of v1 and v2 in the circuit of Fig. 5-20. Applying KCL at nodes A and B,

Fig. 5-20

Node A: Node B:

vA v2 vA þ ¼0 R3 R4 vB v1 vB vo þ ¼0 R1 R2

Set vA ¼ vB and eliminate them from the preceding KCL equations to get

ð16Þ

76

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

vo ¼

R4 ðR1 þ R2 Þ R v 2v R1 ðR3 þ R4 Þ 2 R1 1

[CHAP. 5

ð17Þ

When R3 ¼ R1 and R2 ¼ R4 , (17) is reduced to (16).

5.10

CIRCUITS CONTAINING SEVERAL OP AMPS

The analysis and results developed for single op amp circuits can be applied to circuits containing several ideal op amps in cascade or nested loops because there is no loading eﬀect. EXAMPLE 5.15 Find v1 and v2 in Fig. 5-21.

Fig. 5-21 The ﬁrst op amp is an inverting circuit. v1 ¼ ð3=1Þð0:6Þ ¼ 1:8 V The second op amp is a summing circuit. v2 ¼ ð2=1Þð0:5Þ ð2=2Þð1:8Þ ¼ 2:8 V EXAMPLE 5.16 Let Rs ¼ 1 k in the circuit of Fig. 5-22, ﬁnd v1 ; v2 ; vo ; is ; i1 ; and if as functions of vs for (a) Rf ¼ 1 and (b) Rf ¼ 40 k

Fig. 5-22 (a) Rf ¼ 1. The two inverting op amps are cascaded, with vþ ¼ 0. v1 ¼ From the inverting ampliﬁers we get

5 5 v ¼ v 5þ1 s 6 s

By voltage division in the input loop we have ð18Þ

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

v2 ¼ ð9=5Þv1 ¼ ð9=5Þ

77

5 vs ¼ 1:5vs 6

vo ¼ ð6=1:2Þv2 ¼ 5ð1:5vs Þ ¼ 7:5vs v is ¼ i1 ¼ s ðAÞ ¼ 0:166vs ðmAÞ 6000 if ¼ 0 (b) Rf ¼ 40 k. From the inverting op amps we get vo ¼ 5v2 and v2 ¼ ð9=5Þv1 so that vo ¼ 9v1 . Apply KCL to the currents leaving node B. v1 vs v1 v1 vo þ þ ¼0 ð19Þ 1 5 40 Substitute vo ¼ 9v1 in (19) and solve for v1 to get v1 ¼ vs v2 ¼ ð9=5Þv1 ¼ 1:8vs vo ¼ ð6=1:2Þv2 ¼ 5ð1:8vs Þ ¼ 9vs v v1 ¼0 is ¼ s 1000 Apply KCL at node B. if ¼ i1 ¼

v1 v ðAÞ ¼ s ðAÞ ¼ 0:2vs ðmAÞ 5000 5000

The current i1 in the 5-k input resistor of the ﬁrst op amp is provided by the output of the second op amp through the 40-k feedback resistor. The current is drawn from vs is, therefore, zero. The input resistance of the circuit is inﬁnite.

5.11 INTEGRATOR AND DIFFERENTIATOR CIRCUITS Integrator By replacing the feedback resistor in the inverting ampliﬁer of Fig. 5-13 with a capacitor, the basic integrator circuit shown in Fig. 5-23 will result.

Fig. 5-23

To obtain the input-output relationship apply KCL at the inverting node: v1 dv þC 2 ¼0 R dt and

dv2 1 v ¼ RC 1 dt

from which

v2 ¼

1 RC

ðt v1 dt

(20)

1

In other words, the output is equal to the integral of the input multiplied by a gain factor of 1=RC. EXAMPLE 5.17

In Fig. 5-23 let R ¼ 1 k, C ¼ 1 mF, and v1 ¼ sin 2000t. Assuming v2 ð0Þ ¼ 0, ﬁnd v2 for t > 0.

78

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

v2 ¼

1 103 106

[CHAP. 5

ðt sin 2000t dt ¼ 0:5ðcos 2000t 1Þ 0

Leaky Integrator The circuit of Fig. 5-24 is called a leaky integrator, as the capacitor voltage is continuously discharged through the feedback resistor Rf . This will result in a reduction in gain jv2 =v1 j and a phase shift in v2 . For further discussion see Section 5.13.

Fig. 5-24

EXAMPLE 5.18 In Fig. 5-24, R1 ¼ Rf ¼ 1 k, C ¼ 1 mF, and v1 ¼ sin 2000t. Find v2 . The inverting node is at zero voltage, and the sum of currents arriving at it is zero. Thus, v1 dv v þC 2þ 2 ¼0 R1 dt Rf 103

or

v1 þ 103

dv2 þ v2 ¼ 0 dt

dv2 þ v2 ¼ sin 2000t dt

ð21Þ

The solution for v2 in (21) is a sinusoidal with the same frequency as that of v1 but diﬀerent amplitude and phase angle, i.e., v2 ¼ A cosð2000t þ BÞ To ﬁnd A and B, we substitute v2 and dv2 =dt in (22) into (21).

But Therefore, A ¼

First dv=dt ¼ 2000A sinð2000t þ BÞ.

ð22Þ Thus,

103 dv2 =dt þ v2 ¼ 2A sinð2000t þ BÞ þ A cosð2000t þ BÞ ¼ sin 2000t pﬃﬃﬃ 2A sinð2000t þ BÞ A cosð2000t þ BÞ ¼ A 5 sinð2000t þ B 26:578Þ ¼ sin 2000t pﬃﬃﬃ 5=5 ¼ 0:447, B ¼ 26:578 and v2 ¼ 0:447 cosð2000t þ 26:578Þ

ð23Þ

Integrator-Summer Ampliﬁer A single op amp in an inverting conﬁguration with multiple input lines and a feedback capacitor as shown in Fig. 5-25 can produce the sum of integrals of several functions with desired gains. EXAMPLE 5.19 Find the output vo in the integrator-summer ampliﬁer of Fig. 5-25, where the circuit has three inputs. Apply KCL at the inverting input of the op amp to get

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

79

Fig. 5-25 v1 v v dv þ 2 þ 3 þC o ¼0 R1 R2 R3 dt ðt v1 v v vo ¼ þ 2 þ 3 dt R2 C R3 C 1 R1 C

ð24Þ

Initial Condition of Integration The desired initial condition, vo , of the integration can be provided by a reset switch as shown in Fig. 5-26. By momentarily connecting the switch and then disconnecting it at t ¼ to , an initial value of vo is established across the capacitor and appears at the output v2 . For t > to , the weighted integral of input is added to the output. ð 1 t v2 ¼ v dt þ vo ð25Þ RC to 1

Fig. 5-26

Diﬀerentiator By putting an inductor in place of the resistor in the feedback path of an inverting ampliﬁer, the derivative of the input signal is produced at the output. Figure 5-27 shows the resulting diﬀerentiator circuit. To obtain the input-output relationship, apply KCL to currents arriving at the inverting node:

v1 1 þ R L

ðt v2 dt ¼ 0 1

or

v2 ¼

L dv1 R dt

ð26Þ

80

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-27

5.12

ANALOG COMPUTERS

The inverting ampliﬁers, summing circuits, and integrators described in the previous sections are used as building blocks to form analog computers for solving linear diﬀerential equations. Diﬀerentiators are avoided because of considerable eﬀect of noise despite its low level. To design a computing circuit, ﬁrst rearrange the diﬀerential equation such that the highest existing derivative of the desired variable is on one side of the equation. Add integrators and ampliﬁers in cascade and in nested loops as shown in the following examples. In this section we use the notations x 0 ¼ dx=dt, x 00 ¼ d 2 x=dt2 and so on. EXAMPLE 5.20 Design a circuit with xðtÞ as input to generate output yðtÞ which satisﬁes the following equation: y 00 ðtÞ þ 2y 0 ðtÞ þ 3yðtÞ ¼ xðtÞ

ð27Þ

Step 1. Rearrange the diﬀerential equation (27) as follows: y 00 ¼ x 2y 0 3y

ð28Þ

Step 2. Use the summer-integrator op amp #1 in Fig. 5-28 to integrate (28). Apply (24) to ﬁnd R1 ; R2 ; R3 and C1 such that output of op amp #1 is v1 ¼ y 0 . We let C1 ¼ 1 mF and compute the resistors accordingly: R1 C1 ¼ 1 R1 ¼ 1 M R2 C1 ¼ 1=3 R2 ¼ 333 k R3 C1 ¼ 1=2 R3 ¼ 500 k ð ð v1 ¼ ðx 3y 2y 0 Þ dt ¼ y 00 dt ¼ y 0

ð29Þ

Step 3. Integrate v1 ¼ y 0 by op amp #2 to obtain y. We let C2 ¼ 1 mF and R4 ¼ 1 M to obtain v2 ¼ y at the output of op amp #2. ð ð 1 v2 dt ¼ y 0 dt ¼ y ð30Þ v2 ¼ R4 C2 Step 4. Supply inputs to op amp #1 through the following connections. Feed v1 ¼ y 0 directly back to the R3 input of op amp #1. Pass v2 ¼ y through the unity gain inverting op amp #3 to generate y, and then feed it to the R2 input of op amp #1. Connect the voltage source xðtÞ to the R1 input of op amp #1. The complete circuit is shown in Fig. 5-28. EXAMPLE 5.21 Design an op amp circuit as an ideal voltage source vðtÞ satisfying the equation v 0 þ v ¼ 0 for t > 0, with vð0Þ ¼ 1 V. Following the steps used in Example 5.20, the circuit of Fig. 5-29 with RC ¼ 1 s is assembled. The initial condition is entered when the switch is opened at t ¼ 0. The solution vðtÞ ¼ et , t > 0, is observed at the output of the op amp.

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

81

Fig. 5-28

Fig. 5-29

5.13

LOW-PASS FILTER

A frequency-selective ampliﬁer whose gain decreases from a ﬁnite value to zero as the frequency of the sinusoidal input increases from dc to inﬁnity is called a low-pass ﬁlter. The plot of gain versus frequency is called a frequency response. An easy technique for ﬁnding the frequency response of ﬁlters will be developed in Chapter 13. The leaky integrator of Fig. 5-24 is a low-pass ﬁlter, as illustrated in the following example. EXAMPLE 5.22 In Example 5.18 let v1 ¼ sin ! t. Find jv2 j for ! ¼ 0; 10; 100; 103 ; 104 , and 105 rad/s. By repeating the procedure of Example 5.18, the frequency response is found and given in Table 5-1. response amplitude decreases with frequency. The circuit is a low-pass ﬁlter.

Table 5-1. Frequency Response of the Low-pass Filter !, rad/s

0

f , Hz jv2 =v1 j

0 1

10 1.59 1

100 15.9 0.995

103 159 0.707

104

105

1:59 103 0.1

15:9 103 0.01

The

82

5.14

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

COMPARATOR

The circuit of Fig. 5-30 compares the voltage v1 with a reference level vo . Since the open-loop gain is very large, the op amp output v2 is either at þVcc (if v1 > vo ) or at Vcc (if v1 < vo ). This is shown by v2 ¼ Vcc sgn½v1 vo where ‘‘sgn’’ stands for ‘‘sign of.’’ For vo ¼ 0, we have þVcc v1 > 0 v2 ¼ Vcc sgn½v1 ¼ Vcc v1 < 0

Fig. 5-30 EXAMPLE 5.23 In Fig. 5-30, let Vcc ¼ 5 V, vo ¼ 0, and v1 ¼ sin !t. Find v2 . For 0 < t < =!, v1 ¼ sin !t > 0

v2 ¼ 5 V

For =! < t < 2=!, v1 ¼ sin !t < 0

v2 ¼ 5 V

The output v2 is a square pulse which switches between þ5 V and 5 V with period of 2=!. given by 5V 0 < t < =! v2 ¼ 5 V =! < t < 2=!

One cycle of v2 is

EXAMPLE 5.24 The circuit of Fig. 5-31 is a parallel analog-to-digital converter. The þVcc and Vcc connections are omitted for simplicity. Let Vcc ¼ 5 V, vo ¼ 4 V, and vi ¼ t (V) for 0 < t < 4 s. Find outputs v3 ; v2 ; and v1 . Interpret the answer. The op amps have no feedback, and they function as comparators. The outputs with values at þ5 or 5 V are given in Table 5-2.

Table 5-2 time, s 0
input, V 0 < vi 1 < vi 2 < vi 3 < vi

<1 <2 <3 <4

outputs, V v3 v3 v3 v3

¼ 5 ¼ 5 ¼ 5 ¼ þ5

v2 v2 v2 v2

¼ 5 ¼ 5 ¼ þ5 ¼ þ5

v1 v1 v1 v1

¼ 5 ¼ þ5 ¼ þ5 ¼ þ5

The binary sequences fv3 ; v2 ; v1 g in Table 5-2 uniquely specify the input voltage in discrete domain. However, in their present form they are not the binary numbers representing input amplitudes. Yet, by using a coder we could transform the above sequences into the binary numbers corresponding to the values of analog inputs.

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

83

Fig. 5-31

Solved Problems 5.1

In Fig. 5-3, let vs ¼ 20 V, Rs ¼ 10 , Ri ¼ 990 , k ¼ 5, and Ro ¼ 3 . Find (a) the The´venin equivalent of the circuit seen by Rl and (b) v2 and the power dissipated in Rl for Rl ¼ 0:5, 1, 3, 5, 10, 100, and 1000 . (a) The open-circuit voltage and short-circuit current at A–B terminal are vo:c: ¼ 5v1 and is:c: ¼ 5v1 =3, respectively. We ﬁnd v1 by dividing vs between Rs and Ri . Thus, v1 ¼

Ri 990 ð20Þ ¼ 19:8 V v ¼ Rs þ Ri s 10 þ 990

Fig. 5-32

84

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Therefore, vo:c: ¼ 5ð19:8Þ ¼ 99 V is:c: ¼ 99=3 ¼ 33 A

vTh ¼ vo:c: ¼ 99 V RTh ¼ vo:c: =is:c: ¼ 3

The The´venin equivalent is shown in Fig. 5-32. (b) With the load Rl connected, we have v2 ¼

Rl 99Rl v ¼ Rl þ RTh Th Rl þ 3

and

p¼

v22 Rl

Table 5-3 shows the voltage across the load and the power dissipated in it for the given seven values of Rl . The load voltage is at its maximum when Rl ¼ 1. However, power delivered to Rl ¼ 1 is zero. Power delivered to Rl is maximum at Rl ¼ 3 , which is equal to the output resistance of the ampliﬁer. Table 5-3

5.2

Rl ;

v2 ; V

p; W

0.5 1 3 5 10 100 1000

14.14 24.75 49.50 61.88 76.15 96.12 98.70

400.04 612.56 816.75 765.70 579.94 92.38 9.74

In the circuits of Figs. 5-4 and 5-5 let R1 ¼ 1 k and R2 ¼ 5 k. Find the gains Gþ ¼ v2 =vs in Fig. 5-4 and G ¼ v2 =vs in Fig. 5-5 for k ¼ 1, 2, 4, 6, 8, 10, 100, 1000, and 1. Compare the results. From (5) in Example 5.3, at R1 ¼ 1 k and R2 ¼ 5 k we have v2 5k ¼ vs 6 k

ð31Þ

v2 5k ¼ 6þk vs

ð32Þ

Gþ ¼ In Example 5.4 we found G ¼

The gains G and Gþ are calculated for nine values of k in Table 5-4. As k becomes very large, Gþ and G approach the limit gain of 5, which is the negative of the ratio R2 =R1 and is independent of k. The circuit of Fig. 5-5 (with negative feedback) is always stable and its gain monotonically approaches the limit gain. However, the circuit of Fig. 5-4 (with positive feedback) is unstable. The gain Gþ becomes very large as k approaches six. At k ¼ 6, Gþ ¼ 1. Table 5-4 k 1 2 4 6 8 10 100 1000 1

Gþ

G

1:0 2:5 10:0 1 20:0 12:5 5:32 5:03 5:00

0:71 1:25 2:00 2:50 2:86 3:12 4:72 4:97 5:00

CHAP. 5]

5.3

85

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

Let R1 ¼ 1 k, R2 ¼ 5 k, and Ri ¼ 50 k in the circuit of Fig. 5-33. Find v2 =vs for k ¼ 1, 10, 100, 1000, 1 and compare the results with the values of G in Table 5-4.

Fig. 5-33 This problem is solved by application of KCL at node A (another approach which uses the The´venin equivalent is suggested in Problem 5.30). Thus, v1 vs v1 v2 v1 þ þ ¼0 1 5 50

ð33Þ

or

ð34Þ

From the ampliﬁer we obtain v2 ¼ kv1

v1 ¼ v2 =k

Replacing v1 in (34) into (33) and rearranging terms, we obtain v2 50k 5k ¼ ¼ vs 61 þ 10k 6:1 þ k

ð35Þ

Values of v2 =vs in (35) are shown in Table 5-5 as functions of k. The 50-k input resistance of the ampliﬁer reduces the overall gain very slightly, as seen by comparing Tables 5-4 and 5-5. The feedback has made the input resistance of the ampliﬁer less eﬀective in changing the overall gain. Table 5-5 k 1 10 100 1000 1

5.4

v2 =vs 0:704 3:106 4:713 4:97 5:00

Let again R1 ¼ 1 k and R2 ¼ 5 k in the circuit of Fig. 5-33. ðaÞ ðbÞ ðcÞ

Find v2 =vs as a function of k and Ri : Let Ri ¼ 1 k. Find v2 =v1 for k ¼ 1; 10; 100; 1000; 1. Repeat for Ri ¼ 1: Discuss the effects of Ri and k on the overall gain. Show that, for k ¼ 1 and Ri 6¼ 0; the gain of the amplifier is independent of Ri and is equal to R2 =R1 :

(a) Apply KCL to currents leaving node A to obtain v1 vs v1 v2 v1 þ þ ¼0 1 5 Ri From the ampliﬁer we get v2 ¼ kv1 or v1 ¼ v2 =k. rearranging terms we get

Substituting for v1 in the KCL equation and

86

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

v2 ck ¼ 5 1 þ ck vs

where c ¼

Ri 5 þ 6Ri

[CHAP. 5

ð36Þ

(b) For Ri ¼ 1 k, c ¼ 1=11 which, substituted into (36), gives v2 5k ¼ vs 11 þ k

ð37Þ

v2 5k ¼ vs 6 þ k

ð38Þ

For Ri ¼ 1 we get c ¼ 1=6 and so

Table 5-6 gives values of v2 =vs in (37) and (38) versus k. Note that (38) is identical with (32).

Table 5-6 v2 =vs

(c)

5.5

k

Ri ¼ 1 k

Ri ¼ 1

1 10 100 1000 1

0:31 2:38 4:51 4:95 5:00

0:71 3:12 4:72 4:97 5:00

Comparing the two columns in Table 5-6 we see that the smaller Ri reduces the overall gain G . However, as the open-loop gain k increases, the eﬀect of Ri is diminished. As k becomes very large, v2 =v1 approaches 5 unless Ri ¼ 0.

Let again R1 ¼ 1 k and R2 ¼ 5 k in the circuit of Fig. 5-33. Replace the circuit to the left of node A including vs , R1 , and Ri by its The´venin equivalent. Then use (5) to derive (36). The The´venin equivalent is given by R i vs Rv ¼ i s R1 þ Ri 1 þ Ri R1 Ri Ri ¼ ¼ R1 þ Ri 1 þ Ri

vTh ¼ RTh where the resistors are in k: From (5),

v2 ¼ ð1 bÞ where

b¼

RTh Ri ¼ RTh þ R2 6Ri þ 5

k v 1 þ bk Th and

1b¼

5ð1 þ Ri Þ 6Ri þ 5

Therefore, v2 ¼

5ð1 þ Ri Þ k Ri 5Ri k v v ¼ 6Ri þ 5 1 þ Ri k=ð6Ri þ 5Þ 1 þ Ri s 6Ri þ 5 þ Ri k s

which is identical with (36).

5.6

Find the output voltage of an op amp with A ¼ 105 and Vcc ¼ 10 V for v ¼ 0 and vþ ¼ sin t (V). Refer to Figs. 5-7 and 5-8.

CHAP. 5]

87

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

Because of high gain, saturation occurs quickly at jv2 j ¼ 105 jvd j ¼ 10 V

jvd j ¼ 104 V

or

We may ignore the linear interval and write v2 ¼ where vd ¼ vþ v ¼ sin t (V).

þ10 V 10 V

vd > 0 vd < 0

One cycle of the output is given by þ10 V 0
For a more exact v2 , we use the transfer characteristic of the op amp in Fig. 5-7. 8 < 10 vd < 104 V 5 4 v2 ¼ 10 vd 10 < vd < 104 V : þ10 vd > 104 V Saturation begins at jvd j ¼ j sin tj ¼ 104 V. output v2 is then given by v2 v2 v2 v2

Since this is a very small range, we may replace sin t by t.

¼ 105 t ¼ 10 ¼ 105 ðt Þ ¼ 10

104 104 104 þ 104

The

< t < 104 s < t < 104 s < t < þ 104 s < t < 2 104 s

To appreciate the insigniﬁcance of error in ignoring the linear range, note that during one period of 2 s the interval of linear operation is only 4 104 s, which gives a ratio of 64 106 .

5.7

Repeat Problem 5.6 for vþ ¼ sin 2t (V) and v ¼ 0:5 V. The output voltage is 10 V

when vþ > v

v2 ¼ 10 V

when vþ < v

v2 ¼

Switching occurs when sin 2t ¼ 1=2. cycle of v2 is given by

This happens at t ¼ 1=12, 5/12, 13/12, and so on.

v2 ¼ 10 V v2 ¼ 10 V

Therefore, one

1=12 < t < 5=12 s 5=12 < t < 13=12 s

Figure 5-34 shows the graphs of vþ , v , and v2 .

5.8

In the circuit of Fig. 5-35 vs ¼ sin 100t.

Find v1 and v2 .

At nodes B and A, vB ¼ vA ¼ 0. Then, 30 v ¼ 0:6 sin 100t ðVÞ 20 þ 30 s 100 100 v2 ¼ v ¼ ð0:6 sin 100tÞ ¼ 2 sin 100t ðVÞ 30 1 30 100 v ¼ 2 sin 100t ðVÞ v2 ¼ 20 þ 30 s v1 ¼

Alternatively,

5.9

Saturation levels for the op amps in Fig. 5-31 are þVcc ¼ 5 V and Vcc ¼ 5 V. The reference voltage is vo ¼ 1 V. Find the sequence of outputs corresponding to values of vi from 0 to 1 V in steps of 0.25 V.

88

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

Fig. 5-34

Fig. 5-35

See Table 5-7 where L ¼ 5 V and H ¼ þ5 V.

Table 5-7 vi , V 0 to 0.25

0.25þ to 0:5 þ

0.5 to 0.75 þ

0.75 to 1

5.10

Find v in the circuit of Fig. 5-36. Apply KCL at node A,

v3

v2

v1

L

L

L

L

L

H

L

H

H

H

H

H

[CHAP. 5

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

89

Fig. 5-36 ðv v1 Þg1 þ ðv v2 Þg2 þ ðv v3 Þg3 ¼ 0 Then

5.11

v g þ v2 g2 þ v3 g3 v1 R2 R3 þ v2 R1 R3 þ v3 R2 R1 ¼ v¼ 1 1 g1 þ g2 þ g3 R1 R2 þ R2 R3 þ R3 R1

In the circuit of Fig. 5-37 ﬁnd vC (the voltage at node C), i1 , Rin (the input resistance seen by the 9-V source), v2 , and i2 .

Fig. 5-37 At nodes B and A, vB ¼ vA ¼ 0.

Applying KCL at node C, we get

ðvC 9Þ=4 þ vC =6 þ vC =3 ¼ 0 Then

i1 ¼ ð9 vC Þ=4 ¼ 1:5 A

and

from which

vC ¼ 3 V

Rin ¼ v1 =i1 ¼ 9=1:5 ¼ 6

From the inverting ampliﬁer circuit we have v2 ¼ ð5=3ÞvC ¼ 5 V

5.12

and

i2 ¼ 5=10 ¼ 0:5 A

Find v2 in Problem 5.11 by replacing the circuit to the left of nodes A-B in Fig. 5-37 by its The´venin equivalent. RTh ¼ 3 þ

ð6Þð4Þ ¼ 5:4 6þ4

and

vTh ¼

6 ð9Þ ¼ 5:4 V 4þ6

Then v2 ¼ ð5=5:4Þð5:4Þ ¼ 5 V.

5.13

Find vC , i1 , v2 , and Rin , the input resistance seen by the 21-V source in Fig. 5-38. From the inverting ampliﬁer we get v2 ¼ ð5=3ÞvC Note that vB ¼ vA ¼ 0 and so KCL at node C results in

ð39Þ

90

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-38 vC 21 vC vC vC v2 þ þ þ ¼0 3 6 3 8

ð40Þ

Substituting vC ¼ ð3=5Þv2 from (39) into (40) we get v2 ¼ 10 V. Then vC ¼ 6 V i1 ¼ ð21 vC Þ=3000 ¼ 0:005 A ¼ 5 mA Rin ¼ 21=i1 ¼ 21=0:005 ¼ 4200 ¼ 4:2 k

5.14

In the circuit of Fig. 5-38 change the 21-V source by a factor of k. Show that vC , i1 , v2 in Problem 5.13 are changed by the same factor but Rin remains unchanged. Let vs ¼ 21k (V) represent the new voltage source. From the inverting ampliﬁer we have [see (39)] v2 ¼ ð5=3ÞvC Apply KCL at node C to obtain [see (40)] vC vs vC vC vC v2 þ þ þ ¼0 3 6 3 8 Solving for vC and v2 , we have vC ¼ ð6=21Þvs ¼ 6k ðVÞ

and

v2 ¼ ð10=21Þvs ¼ 10k ðVÞ

i1 ¼ ðvs vC Þ=3000 ¼ ð21 6Þk=3000 ¼ 0:005k A Rin ¼ vs =i1 ¼ 21k=0:005k ¼ 4200 These results are expected since the circuit is linear.

5.15

Find v2 and vC in Problem 5.13 by replacing the circuit to the left of node C in Fig. 5-38 (including the 21-V battery and the 3-k and 6-k resistors) by its The´venin equivalent. We ﬁrst compute the The´venin equivalent: RTh ¼

ð6Þð3Þ ¼ 2 k 6þ3

and

vTh ¼

6 ð21Þ ¼ 14 V 3þ6

Replace the circuit to the left of node C by the above vTh and RTh and then apply KCL at C: vC 14 vC vC v2 þ þ ¼0 2 3 8

ð41Þ

For the inverting ampliﬁer we have v2 ¼ ð5=3ÞvC or vC ¼ 0:6 v2 , which results, after substitution in (41), in v2 ¼ 10 V and vC ¼ 6 V.

CHAP. 5]

5.16

91

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

(a) Find the The´venin equivalent of the circuit to the left of nodes A-B in Fig. 5-39(a) and then ﬁnd v2 for Rl ¼ 1 k, 10 k, and 1. (b) Repeat for Fig. 5-39(c) and compare with part (a). (a) The The´venin equivalent of the circuit in Fig. 5-39(a) is shown in Fig. 5-39(b).

Fig. 5-39 vTh ¼

6 ð15Þ ¼ 10 V 6þ3

and

RTh ¼

ð3Þð6Þ ¼ 2 k 3þ6

By dividing vTh between RTh and Rl we get v2 ¼ For Rl For Rl For Rl The output

¼ 1 k, ¼ 10 k, ¼1 v2 depends on

Rl ð10Þ Rl þ 2

v2 ¼ 3:33 V v2 ¼ 8:33 V v2 ¼ 10 V Rl . The operation of the voltage divider is also aﬀected by Rl .

(b) The The´venin equivalent of the circuit in Fig. 5-39(c) is shown in Fig. 5-12(d). vTh ¼ 10 V

and

Here we have

RTh ¼ 0

and v2 ¼ vTh ¼ 10 V for all values of Rl , that is, the output v2 depends on R1 , R2 , and vs only and is independent of Rl .

92

5.17

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Find v2 as a function of i1 in the circuit of Fig. 5-40(a).

Fig. 5-40 Current i1 goes through resistor R producing a voltage Ri1 across it from right to left. Since the inverting terminal B is zero potential, the preceding voltage appears at the output as v2 ¼ Ri1 [see Fig. 540(b)]. Therefore, the op amp converts the current i1 to a voltage v2 with a gain of jv2 =i1 j ¼ R. The current source i1 delivers no power as the voltage vAB across it is zero.

5.18

A transducer generates a weak current i1 which feeds a load Rl and produces a voltage v1 across it. It is desired that v1 follow the signal with a constant gain of 108 regardless of the value of Rl . Design a current-to-voltage converter to accomplish this task. The transducer should feed Rl indirectly through an op amp. The following designs produce v1 ¼ 108 i1 independently of Rl . Design 1: Choose R ¼ 100 M in Fig. 5-40. not readily available.

However, a resistor of such a large magnitude is expensive and

Design 2: The conversion gain of 108 V=A is also obtained in the circuit of Fig. 5-41. The ﬁrst op amp with R ¼ 106 converts i1 to v1 ¼ 106 i1 . The second ampliﬁer with a gain of 100 (e.g., R1 ¼ 1 k and R2 ¼ 100 k) ampliﬁes v1 to v2 ¼ 100v1 ¼ 108 i1 . The circuit requires two op amps and three resistors (1 M, 100 k, and 1 k) which are less expensive and more readily available.

Fig. 5-41 Design 3: See Fig. 5-42 and Problem 5.19.

5.19

Determine the resistor values which would produce a current-to-voltage conversion gain of v2 =i1 ¼ 108 V=A in the circuit of Fig. 5-42.

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

93

Fig. 5-42 Apply KCL at node C.

Note that vB ¼ vA ¼ 0.

Thus,

vC vC vC v2 þ ¼0 þ R R1 R2 Substituting vC ¼ Ri1 and solving for v2 we get v2 ¼ Req i1

where Req

R2 R2 ¼R 1þ þ R1 R

For a conversion gain of v2 =i1 ¼ Req ¼ 108 V=A ¼ 100 M, we need to ﬁnd resistor values to satisfy the following equation: R R R 1 þ 2 þ 2 ¼ 108 R1 R One solution is to choose R ¼ 1 M, R1 ¼ 1 k, and R2 ¼ 99 k. The design of Fig. 5-42 uses a single op amp and three resistors which are not expensive and are readily available.

5.20

Find i2 as a function of v1 in the circuit of Fig. 5-43.

Fig. 5-43 We have vB ¼ vA ¼ 0

i1 ¼ v1 =R1

i2 ¼ i1 ¼ v1 =R1

The op amp converts the voltage source to a ﬂoating current source. ratio is R1 and is independent of R2 .

5.21

The voltage-to-current conversion

A practical current source (is in parallel with internal resistance Rs ) directly feeds a load Rl as in Fig. 5-44(a). (a) Find load current il . (b) Place an op amp between the source and the load as in Fig. 5-44(b). Find il and compare with part (a).

94

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-44 (a) In the direct connection, Fig. 5-44(a), il ¼ is Rs =ðRs þ Rl Þ, which varies with Rl . (b) In Fig. 5-44(b), the op amp forces vB to zero causing the current in Rs to become zero. Therefore, il ¼ is which is now independent of Rl . The op amp circuit converts the practical current source to an ideal current source. See Figure 5-44(c).

5.22

Find vo in the circuit of Fig. 5-45.

Fig. 5-45 The ﬁrst op amp is a unity gain inverter with v3 ¼ v2 . The second op amp is a summing circuit with a gain of R2 =R1 for both inputs v1 and v3 . The output is vo ¼

R2 R ðv þ v3 Þ ¼ 2 ðv2 v1 Þ R1 1 R1

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

95

The circuit is a diﬀerence ampliﬁer.

5.23

Find vo in the circuit of Fig. 5-46.

Fig. 5-46 Apply KCL at node B.

Note that vB ¼ vA ¼ v2 .

Thus,

v2 v1 v2 vo þ ¼0 R1 R2 Solving for vo , we get vo ¼ v2 þ ðR2 =R1 Þðv2 v1 Þ.

5.24

Find vo in the circuit of Fig. 5-47.

Fig. 5-47 The left part of the circuit has a gain of ð1 þ R1 =R2 Þ. Therefore, v3 ¼ ð1 þ R1 =R2 Þv1 . Using results of Problem 5.23 and substituting for v3 results in R R R R R vo ¼ v2 þ 2 ðv2 v3 Þ ¼ 1 þ 2 v2 2 1 þ 1 v1 ¼ 1 þ 2 ðv2 v1 Þ R1 R1 R1 R2 R1

5.25

In Fig. 5-48 choose resistors for a diﬀerential gain of 106 so that vo ¼ 106 ðv2 v1 Þ. The two frontal op amps are voltage followers. vA ¼ v1

and

vB ¼ v2

From (16), Sec. 5.9, we have vo ¼

R2 R ðv vA Þ ¼ 2 ðv2 v1 Þ R1 B R1

To obtain the required diﬀerential gain of R2 =R1 ¼ 106 , choose R1 ¼ 100 and R2 ¼ 100 M.

96

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

Fig. 5-48 The circuit of Fig. 5-48 can have the same gain as that of Fig. 5-45, but its input resistance is inﬁnite. However, it employs two small and large resistors which are rather out of ordinary range.

5.26

Resistors having high magnitude and accuracy are expensive. Show that in the circuit of Fig. 549 we can choose resistors of ordinary range so that vo ¼ 106 ðv2 v1 Þ.

Fig. 5-49 The two frontal op amps convey the input voltages v1 and v2 to the terminals of RG , creating an upward current i ¼ ðv2 v1 Þ=RG in the resistor. The current also goes through the two R3 resistors, creating voltage drops iR3 across them. Therefore, R3 R ðv v1 Þ vB ¼ v2 þ R3 i ¼ v2 þ 3 ðv2 v1 Þ RG 2 RG 2R vB vA ¼ 1 þ 3 ðv2 v1 Þ RG R R 2R vo ¼ 2 ðvB vA Þ ¼ 2 1 þ 3 ðv2 v1 Þ R1 R1 RG

vA ¼ v1 R 3 i ¼ v1

and

For a diﬀerential gain of 106 we must have vo R 2R ¼ 2 1 þ 3 ¼ 106 v2 v1 R1 RG Choose R1 ¼ RG ¼ 1 k, R2 ¼ 100 k, and R3 ¼ 5 M.

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

97

The circuit of Fig. 5-49 has an inﬁnite input resistance, employs resistors within ordinary range, and uses three op amps.

5.27

Show that in the circuit of Fig. 5-50 i1 ¼ i2 , regardless of the circuits of N1 and N2 .

Fig. 5-50 Nodes A and B are at the same voltage vA ¼ vB . Since the op amp draws no current, i1 and i2 ﬂow through the two resistors and KVL around the op amp loop ABC gives Ri1 Ri2 ¼ 0. Therefore, i1 ¼ i2 .

5.28

Let N1 be the voltage source v1 and N2 be the resistor R2 in the circuit of Fig. 5-50. input resistance Rin ¼ v1 =i1 .

Find the

From the op amp we obtain vA ¼ vB and i1 ¼ i2 . From connections to N1 and N2 we obtain v1 ¼ vB ¼ v2 ¼ vA and v2 ¼ i2 R2 , respectively. The input resistance is v1 =i1 ¼ i2 R2 =i2 ¼ R2 which is the negative of the load. The op amp circuit is a negative impedance converter.

5.29

A voltage follower is constructed using an op amp with a ﬁnite open-loop gain A and Rin ¼ 1 (see Fig. 5-51). Find the gain G ¼ v2 =v1 . Deﬁning sensitivity s as the ratio of percentage change produced in G to the percentage change in A, ﬁnd s.

Fig. 5-51 From Fig. 5-51 we have v2 ¼ Avd .

Applying KVL around the ampliﬁer, obtain

v1 ¼ vd þ v2 ¼ vd þ Avd ¼ vd ð1 þ AÞ ¼ v2 ð1 þ AÞ=A G¼

v2 A ¼ v1 1 þ A

98

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

The rate of change of G with respect to A is dG 1 ¼ dA ð1 þ AÞ2

from which

dG ¼

dA ð1 þ AÞ2

The percentage change produced in G is 100ðdG=GÞ. dG dA 1þA 1 dA ¼ ¼ G A 1þA A ð1 þ AÞ2 and the sensitivity is s¼ The percentage change in G depends on A.

dG=G 1 ¼ dA=A 1 þ A

Samples of dG=dA and s are shown in Table 5-8. Table 5-8

A 10 11 100 1000

G ¼ v2 =v1

dG=dA

s

0.909 0.917 0.990 0.999

0.008 0.007 0.0001 0

0.091 0.083 0.01 0

For high values of A, the gain G is not sensitive to changes in A.

Supplementary Problems 5.30

Repeat Problem 5.3 by replacing the circuit to the left of node B (including vs , R1 , and Ri ) by its The´venin equivalent (see Fig. 5-33) Solve the problem by applying the results of Example 5.4.

5.31

Find the The´venin equivalent of the circuit to the left of nodes A-B in Fig. 5-52 with k ¼ 10 for (a) R2 ¼ 1 and (b) R2 ¼ 50 k. Ans: ðaÞ vTh ¼ 100 V; RTh ¼ 100 ; (bÞ vTh ¼ 31:22 V; RTh ¼ 37:48

Fig. 5-52

5.32

Repeat Problem 5.31 for R2 ¼ 50 k and k ¼ 100.

5.33

Determine the relationship between R, R1 , and R2 in Fig. 5-41 such that the circuit has a gain of v2 =i1 ¼ 106 V/A. Ans: RR2 =R1 ¼ 106

Ans:

vTh ¼ 47:16 V; RTh ¼ 5:66

CHAP. 5]

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

99

5.34

In the circuit of Fig. 5-13, Vcc ¼ 10 V, R1 ¼ 2 k and v1 ¼ 1 V. Find the maximum value of R2 before the op amp is saturated. Ans: R2 ¼ 20 k

5.35

Let the summing circuit of Fig. 5-14 have two inputs with v1 ¼ 1 and v2 ¼ sin t (V). Let R1 ¼ 3 k, R2 ¼ 5 k, and Rf ¼ 8 k. Apply superposition to ﬁnd vo . Ans: vo ¼ ð83 þ 85 sin tÞ

5.36

In Fig. 5-17 let R1 ¼ 4 k and R2 ¼ 8 k. Ans: vo ¼ v1 þ v2 þ v3

5.37

Find the input resistance seen by vf in Fig. 5-19.

5.38

Use superposition to ﬁnd vo in Fig. 5-20 for R1 ¼ 2, R2 ¼ 7, R3 ¼ 10, R4 ¼ 5, all values in k. Ans: vo ¼ 1:5v2 3:5v1

5.39

In the circuit of Fig. 5-20 ﬁnd (a) v0 for R1 ¼ 1, R2 ¼ 3, R3 ¼ 2, and R4 ¼ 2, all values in k; (b) the input resistance R2 in seen by v2 ; (c) i1 as a function of v1 and v2 and show that v1 sees a variable load which depends on v2 . Ans: ðaÞ vo ¼ 2v2 3v1 ; ðbÞ R2 in ¼ 4 k; ðcÞ i1 ¼ v1 v2 =2

5.40

Using a single op amp, design an ampliﬁer with a gain of v2 =v1 ¼ 3=4, input resistance of 8 k, and zero output resistance. Ans: See Fig. 5-53.

Apply superposition to ﬁnd vo in terms of the input voltages.

Ans:

Rin ¼ 2R1

Fig. 5-53

5.41

Show that, given R1 ¼ 1 and R2 ¼ 0, the noninverting op amp circuit of Fig. 5-15 and (12) is reduced to a voltage follower.

5.42

In the circuit of Fig. 5-22 let Rs ¼ 10 k. Discuss. Ans: ðaÞ 40 k; ðbÞ yes

5.43

The input to the circuit of Fig. 5-23 with RC ¼ 1 is v1 ¼ sin !t. Ans: v2 ¼ ð1=!Þ cos !t þ C

5.44

Show that the output v2 in Fig. 5.54 is the same as the output of the integrator in Fig. 5-23.

(a) Find Rf such that is ¼ 0.

Fig. 5-54

(b) Is Rf independent of Rs ?

Write KCL at node B and solve for v2 .

100

AMPLIFIERS AND OPERATIONAL AMPLIFIER CIRCUITS

[CHAP. 5

5.45

Find v2 in the leaky integrator of Fig. 5-24 with R1 ¼ Rf ¼ 1 k, C ¼ 1 mF, and v1 ¼ ( Ans:

v2 ðtÞ ¼

1 þ e1000t ðVÞ 0

1V 0

t>0 . t<0

t>0 t<0 1V 0

t<0 . t>0

e1000t ðVÞ 1 V

t>0 t<0

5.46

Repeat Problem 5.45 for v1 ¼

5.47

In the diﬀerential equation 102 dv2 =dt þ v2 ¼ vs , vs is the forcing function and v2 is the response. Design an op amp circuit to obtain v2 from vs . Ans: See Fig. 5-24, with R1 ¼ Rf ; RC ¼ 102 , and v1 ¼ vs .

5.48

Design a circuit containing op amps to solve the following set of equations:

Ans:

v2 ðtÞ ¼

y 0 þ x ¼ vs1 2y þ x 0 þ 3x ¼ vs2 Ans. See Fig. 5-55, with R1 C ¼ R4 C ¼ 1 s, R2 C ¼ 13 s, R3 C ¼ 12 s.

Fig. 5-55

Waveforms and Signals 6.1

INTRODUCTION The voltages and currents in electric circuits are described by three classes of time functions: (i) (ii)

Periodic functions Nonperiodic functions

(iii)

Random functions

In this chapter the time domain of all functions is 1 < t < 1 and the terms function, waveform, and signal are used interchangeably.

6.2

PERIODIC FUNCTIONS A signal vðtÞ is periodic with period T if vðtÞ ¼ vðt þ TÞ

for all t

Four types of periodic functions which are speciﬁed for one period T and corresponding graphs are as follows: (a) Sine wave: v1 ðtÞ ¼ V0 sin 2t=T See Fig. 6-1(a).

Fig. 6-1(a)

101 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

ð1Þ

102

WAVEFORMS AND SIGNALS

[CHAP. 6

(b) Periodic pulse: v2 ðtÞ ¼

for 0 < t < T1 for T1 < t < T

V1 V2

ð2Þ

See Fig. 6-1(b).

Fig. 6-1(b)

(c) Periodic tone burst: v3 ðtÞ ¼ where T ¼ k and k is an integer.

V0 sin 2t= 0

for 0 < t < T1 for T1 < t < T

ð3Þ

See Fig. 6-1(c).

Fig. 6-1(c)

(d) Repetition of a recording every T seconds: v4 ðtÞ

ð4Þ

See Fig. 6-1(d).

Fig. 6-1(d)

Periodic signals may be very complex. However, as will be seen in Chapter 17, they may be represented by a sum of sinusoids. This type of function will be developed in the following sections.

CHAP. 6]

6.3

103

WAVEFORMS AND SIGNALS

SINUSOIDAL FUNCTIONS A sinusoidal voltage vðtÞ is given by vðtÞ ¼ V0 cos ð!t þ Þ

where V0 is the amplitude, ! is the angular velocity, or angular frequency, and is the phase angle. The angular velocity ! may be expressed in terms of the period T or the frequency f, where f 1=T. The frequency is given in hertz, Hz, or cycles/s. Since cos !t ¼ cos tð!t þ 2Þ, ! and T are related by !T ¼ 2. And since it takes T seconds for vðtÞ to return to its original value, it goes through 1=T cycles in one second. In summary, for sinusoidal functions we have ! ¼ 2=T ¼ 2f

f ¼ 1=T ¼ !=2

T ¼ 1=f ¼ 2=!

EXAMPLE 6.1 Graph each of the following functions and specify period and frequency. ðaÞ v1 ðtÞ ¼ cos t

ðbÞ v2 ðtÞ ¼ sin t

ðcÞ v3 ðtÞ ¼ 2 cos 2t

ðdÞ v4 ðtÞ ¼ 2 cos ðt=4 458Þ ¼ 2 cos ðt=4 =4Þ ¼ 2 cos½ðt 1Þ=4 ðeÞ v5 ðtÞ ¼ 5 cos ð10t þ 608Þ ¼ 5 cos ð10t þ =3Þ ¼ 5 cos 10ðt þ =30Þ (a) See Fig. 6-2(a).

T ¼ 2 ¼ 6:2832 s and f ¼ 0:159 Hz.

(b) See Fig. 6-2(b).

T ¼ 2 ¼ 6:2832 s and f ¼ 0:159 Hz.

(c)

T ¼ 1 s and f ¼ 1 Hz.

See Fig. 6-2(c).

(d) See Fig. 6-2(d).

T ¼ 8 s and f ¼ 0:125 Hz.

(e)

T ¼ 0:2 ¼ 0:62832 s and f ¼ 1:59 Hz.

See Fig. 6-2(e).

EXAMPLE 6.2 Plot vðtÞ ¼ 5 cos !t versus !t. See Fig. 6.3.

6.4

TIME SHIFT AND PHASE SHIFT

If the function vðtÞ ¼ cos !t is delayed by seconds, we get vðt Þ ¼ cos !ðt Þ ¼ cos ð!t Þ, where ¼ !. The delay shifts the graph of vðtÞ to the right by an amount of seconds, which corresponds to a phase lag of ¼ ! ¼ 2f . A time shift of seconds to the left on the graph produces vðt þ Þ, resulting in a leading phase angle called an advance. Conversely, a phase shift of corresponds to a time shift of . Therefore, for a given phase shift the higher is the frequency, the smaller is the required time shift. EXAMPLE 6.3 Plot vðtÞ ¼ 5 cos ðt=6 þ 308Þ versus t and t=6. Rewrite the given as vðtÞ ¼ 5 cos ðt=6 þ =6Þ ¼ 5 cos½ðt þ 1Þ=6 This is a cosine function with period of 12 s, which is advanced in time by 1 s. the left by 1 s or 308 as shown in Fig. 6-4.

In other words, the graph is shifted to

EXAMPLE 6.4 Consider a linear circuit with the following input-output pair valid for all ! and A: Input:

vi ðtÞ ¼ A cos !t

Output:

v0 ðtÞ ¼ A cosð!t Þ

Given vi ðtÞ ¼ cos !1 t þ cos !2 t, ﬁnd v0 ðtÞ when (a) ¼ 106 ! [phase shift is proportional to frequency, Fig. 6-5(a)] (b) ¼ 106 [phase shift is constant, Fig. 6-5(b)] The output is v0 ðtÞ ¼ cos ð!1 t 1 Þ þ cos ð!2 t 2 Þ.

104

WAVEFORMS AND SIGNALS

Fig. 6-2

[CHAP. 6

CHAP. 6]

WAVEFORMS AND SIGNALS

105

Fig. 6-3

Fig. 6-4

Fig. 6-5

(a) 1 ¼ 106 !1 , 2 ¼ 106 !2 . Then v0 ðtÞ ¼ cos ð!1 t 106 !1 Þ þ cos ð!2 t 106 !2 Þ ¼ cos !1 ðt 106 Þ þ cos !2 ðt 106 Þ ¼ vi ðt 106 Þ ¼ vi ðt Þ where ¼ 106 s ¼ 1 ms. Thus a phase shift proportional to ! [Fig. 6-5(a)] delays all frequency components of the input signal by 1 ms. The output follows the input with no distortion. (b) 1 ¼ 2 ¼ 106 .

Then v0 ðtÞ ¼ cos ð!1 t 106 Þ þ cos ð!2 t 106 Þ ¼ cos !1 ðt 106 =!1 Þ þ cos !2 ðt 106 =!2 Þ

A constant phase shift [Fig. 6-5(b)] delays diﬀerent frequency components of the input signal by diﬀerent amounts. The output is a distorted form of the input.

106

6.5

WAVEFORMS AND SIGNALS

[CHAP. 6

COMBINATIONS OF PERIODIC FUNCTIONS

The sum of two periodic functions with respective periods T1 and T2 is a periodic function if a common period T ¼ n1 T1 ¼ n2 T2 , where n1 and n2 are integers, can be found. This requires T1 =T2 ¼ n2 =n1 to be a rational number. Otherwise, the sum is not a periodic function. EXAMPLE 6.5 Find the period of vðtÞ ¼ cos 5t þ 3 sinð3t þ 458Þ. The period of cos 5t is T1 ¼ 2=5 and the period of 3 sinð3t þ 458Þ is T2 ¼ 2=3. Take T ¼ 2 ¼ 5T1 ¼ 3T2 which is the smallest common integral multiple of T1 and T2 . Observe that vðt þ TÞ ¼ vðtÞ since vðt þ TÞ ¼ cos 5ðt þ 2Þ þ 3 sin½3ðt þ 2Þ þ 458 ¼ cos 5t þ 3 sinð3t þ 458Þ ¼ vðtÞ Therefore, the period of vðtÞ is 2. EXAMPLE 6.6 Is vðtÞ ¼ cos t þ cos 2t periodic? Discuss. The period of cos t is T1 ¼ 2. The period of cos 2t is T2 ¼ 1. No common period T ¼ n1 T1 ¼ n2 T2 exists because T1 =T2 ¼ 2 is not a rational number. Therefore, vðtÞ is not periodic. EXAMPLE 6.7 Given p ¼ 3:14, ﬁnd the period of vðtÞ ¼ cos t þ cos 2pt. The period of cos t is T1 ¼ 2 and the period of cos 2pt is T2 ¼ =3:14. The ratio T1 =T2 ¼ 6:28 is a rational number. The integer pair n1 ¼ 25 and n2 ¼ 157 satisﬁes the relation n2 =n1 ¼ T1 =T2 ¼ 628=100 ¼ 157=25. Therefore, vðtÞ is periodic with period T ¼ n1 T1 ¼ n2 T2 ¼ 50 s.

Trigonometric Identities The trigonometric identities in Table 6-1 are useful in the study of circuit analysis. Table 6-1 sin a ¼ sinðaÞ

(5a)

cos a ¼ cos ðaÞ

(5b)

sin a ¼ cos ða 908Þ

(5c)

cos a ¼ sinða þ 908Þ

(5d)

sin 2a ¼ 2 sin a cos a

(6a)

cos 2a ¼ cos2 a sin2 a ¼ 2 cos2 a 1 ¼ 1 2 sin2 a 1 cos 2a sin2 a ¼ 2 1 þ cos 2a 2 cos a ¼ 2 sinða þ bÞ ¼ sin a cos b þ cos a sin b

(6b) (7a)

(8a)

cosða þ bÞ ¼ cos a cos b sin a sin b

(8b)

sin a sin b ¼ 12 cos ða bÞ 12 cos ða þ bÞ sin a cos b ¼ 12 sin ða þ bÞ þ 12 sin ða bÞ cos a cos b ¼ 12 cos ða þ bÞ þ 12 cos ða bÞ sin a þ sin b ¼ 2 sin 12 ða þ bÞ cos 12 ða bÞ cos a þ cos b ¼ 2 cos 12 ða þ bÞ cos 12 ða bÞ

(9a)

(7b)

(9b) (9c) (10a) (10b)

EXAMPLE 6.8 Express vðtÞ ¼ cos 5t sinð3t þ 458Þ as the sum of two cosine functions and ﬁnd its period. vðtÞ ¼ cos 5t sinð3t þ 458Þ ¼ ½sinð8t þ 458Þ sinð2t 458Þ=2 [Eq. ð9bÞ ¼ ½cos ð8t 458Þ þ cos ð2t þ 458Þ=2 [Eq. (5cÞ The period of vðtÞ is .

CHAP. 6]

6.6

107

WAVEFORMS AND SIGNALS

THE AVERAGE AND EFFECTIVE (RMS) VALUES A periodic function f ðtÞ, with a period T, has an average value Favg given by ð ð 1 T 1 t0 þT f ðtÞ dt ¼ f ðtÞ dt Favg ¼ h f ðtÞi ¼ T 0 T t0

ð11Þ

The root-mean-square (rms) or eﬀective value of f ðtÞ during the same period is deﬁned by ð t0 þT 1=2 1 Feff ¼ Frms ¼ f 2 ðtÞ dt T t0

ð12Þ

2 It is seen that Feff ¼ h f 2 ðtÞi. Average and eﬀective values of periodic functions are normally computed over one period.

EXAMPLE 6.9 Find the average and eﬀective values of the cosine wave vðtÞ ¼ Vm cos ð!t þ Þ. Using (11), ð 1 T V V cos ð!t þ Þ dt ¼ m ½sinð!t þ ÞT0 ¼ 0 Vavg ¼ T 0 m !T

ð13Þ

and using (12), 2 ¼ Veff

1 T

ðT

Vm2 cos2 ð!t þ Þ dt ¼

0

1 2T

ðT

Vm2 ½1 þ cos 2ð!t þ Þ dt ¼ Vm2 =2

0

pﬃﬃﬃ Veff ¼ Vm = 2 ¼ 0:707Vm

from which

Equations (13) and (14) show that the results are independent of the frequency and phase angle . the average of a cosine wave and its rms value are always 0 and 0.707 Vm , respectively. EXAMPLE 6.10

Find Vavg and Veff of the half-rectiﬁed sine wave Vm sin !t when sin !t > 0 vðtÞ ¼ 0 when sin !t < 0

(14) In other words,

ð15Þ

From (11), Vavg ¼

1 T

ð T=2 Vm sin !t dt ¼ 0

Vm ½ cos !tT=2 ¼ Vm = 0 !T

ð16Þ

and from (12), 2 ¼ Veff

1 T

ð T =2

Vm2 sin2 !t dt ¼

0

from which EXAMPLE 6.11

We have

ð T=2

Vm2 ð1 cos 2!tÞ dt ¼ Vm2 =4

0

Veff ¼ Vm =2 Find Vavg and Veff of the periodic function vðtÞ where, for one period T, V0 for 0 < t < T1 vðtÞ ¼ Period T ¼ 3T1 V0 for T1 < t < 3T1 Vavg ¼ 2 ¼ Veff

and

1 2T

V0 V0 ðT 2T1 Þ ¼ 3T 1 3

(17)

ð18Þ

(19)

V02 ðT þ 2T1 Þ ¼ V02 3T 1

from which The preceding result can be generalized as follows.

Veff ¼ V0 If jvðtÞj ¼ V0 then Veff ¼ V0 .

(20)

108

WAVEFORMS AND SIGNALS

[CHAP. 6

EXAMPLE 6.12 Compute the average power dissipated from 0 to T in a resistor connected to a voltage vðtÞ. Replace vðtÞ by a constant voltage Vdc . Find Vdc such that the average power during the period remains the same. p ¼ vi ¼ v2 =R Pavg ¼

1 RT

ðT

v2 ðtÞ dt ¼

0

1 2 V2 Veff ¼ dc R R

or

Vdc ¼ Veff

EXAMPLE 6.13 The current iðtÞ shown in Fig. 6-6 passes through a 1-mF capacitor. Find (a) vac the voltage across the capacitor at t ¼ 5k ms (k ¼ 0; 1; 2; 3; . . .Þ and (b) the value of a constant current source Idc which can produce the same voltage across the above capacitor at t ¼ 5k ms when applied at t > 0. Compare Idc with hiðtÞi, the average of iðtÞ in Fig. 6-6, for a period of 5 ms after t > 0.

Fig. 6-6 (a) At t ¼ 5 ms 1 vac ¼ C

ð 5103

6

3

"ð 3103

iðtÞ dt ¼ 10 ð10 Þ 0

ð 5103 4 dt

0

# 2 dt ¼ 12 4 ¼ 8 V

3103

This is the net charging eﬀect of iðtÞ during each 5-ms interval. Every 5 ms the above amount is added to the capacitor voltage. Therefore, at t ¼ 5k ms, v ¼ 8k (V). (b) With a constant current Idc , the capacitor voltage vdc at t ¼ 5k ms is 3 ð 1 5k10 vdc ¼ Idc dt ¼ 106 ðIdc Þð5k 103 Þ ¼ 103 ð5kÞðIdc Þ C 0

ðVÞ

Since vdc ¼ vac at 5k ms, we obtain 103 ð5kÞðIdc Þ ¼ 8k

or

Idc ¼ 8k=ð5k 103 Þ ¼ 1:6 103 A ¼ 1:6 mA

Note that Idc ¼ hiðtÞi of Fig. 6-6 for any period of 5 ms at t > 0.

6.7

NONPERIODIC FUNCTIONS

A nonperiodic function cannot be speciﬁed for all times by simply knowing a ﬁnite segment. Examples of nonperiodic functions are 0 for t < 0 (21) (a) v1 ðtÞ ¼ 1 for t > 0 8 for t < 0 <0 (22) (b) v2 ðtÞ ¼ 1=T for 0 < t < T : 0 for t > T 0 for t < 0 (c) v3 ðtÞ ¼ (23) for t > 0 et=

CHAP. 6]

WAVEFORMS AND SIGNALS

0 sin !t

for t < 0 for t > 0

109

(24)

(d)

v4 ðtÞ ¼

(e)

v5 ðtÞ ¼

(f)

v6 ðtÞ ¼ et=

for all t

(26)

(g)

v7 ðtÞ ¼ eajtj

for all t

(27)

(h)

ajtj

v8 ðtÞ ¼ e

0 et= cos !t

cos !t

for t < 0 for t > 0

for all t

(25)

(28)

Several of these functions are used as mathematical models and building blocks for actual signals in analysis and design of circuits. Examples are discussed in the following sections.

6.8

THE UNIT STEP FUNCTION The dimensionless unit step function, is deﬁned by 0 for t < 0 uðtÞ ¼ 1 for t > 0 The function is graphed in Fig. 6-7.

ð29Þ

Note that the function is undeﬁned at t ¼ 0.

Fig. 6-7

To illustrate the use of uðtÞ, assume the switch S in the circuit of Fig. 6-8(a) has been in position 1 for t < 0 and is moved to position 2 at t ¼ 0. The voltage across A-B may be expressed by vAB ¼ V0 uðtÞ. The equivalent circuit for the voltage step is shown in Fig. 6-8(b).

Fig. 6-8

EXAMPLE 6.14 The switch in the circuit of Fig. 6-8(a) is moved to position 2 at t ¼ t0 . Express vAB using the step function. The appearance of V0 across A-B is delayed until t ¼ t0 . Replace the argument t in the step function by t t0 and so we have vAB ¼ V0 uðt t0 Þ:

110

WAVEFORMS AND SIGNALS

[CHAP. 6

EXAMPLE 6.15 If the switch in Fig. 6-8(a) is moved to position 2 at t ¼ 0 and then moved back to position 1 at t ¼ 5 s, express vAB using the step function. vAB ¼ V0 ½uðtÞ uðt 5Þ EXAMPLE 6.16 Express vðtÞ, graphed in Fig. 6-9, using the step function.

Fig. 6-9 vðtÞ ¼ ½uðtÞ uðt 2Þ sin t

6.9

THE UNIT IMPULSE FUNCTION

Consider the function sT ðtÞ of Fig. 6-10(a), which is zero for t < 0 and increases uniformly from 0 to 1 in T seconds. Its derivative dT ðtÞ is a pulse of duration T and height 1=T, as seen in Fig. 6-10(b). 8 for t < 0 <0 ð30Þ for 0 < t < T dT ðtÞ ¼ 1=T : 0 for t > T If the transition time T is reduced, the pulse in Fig. 6-10(b) becomes narrower and taller, but the area under the pulse remains equal to 1. If we let T approach zero, in the limit function sT ðtÞ becomes a unit step uðtÞ and its derivative dT ðtÞ becomes a unit pulse ðtÞ with zero width and inﬁnite height. The unit impulse ðtÞ is shown in Fig. 6-10(c). The unit impulse or unit delta function is deﬁned by ð1 ðtÞ ¼ 0

for t 6¼ 0

and

ðtÞ dt ¼ 1

ð31Þ

1

An impulse which is the limit of a narrow pulse with an area A is expressed by AðtÞ. The magnitude A is sometimes called the strength of the impulse. A unit impulse which occurs at t ¼ t0 is expressed by ðt t0 Þ. EXAMPLE 6.17 The voltage across the terminals of a 100-nF capacitor grows linearly, from 0 to 10 V, taking the shape of the function sT ðtÞ in Fig. 6-10(a). Find (a) the charge across the capacitor at t ¼ T and (b) the current iC ðtÞ in the capacitor for T ¼ 1 s, T ¼ 1 ms, and T ¼ 1 ms. (a) At t ¼ T, vC ¼ 10 V. The charge across the capacitor is Q ¼ CvC ¼ 107 10 ¼ 106 . ðbÞ

ic ðtÞ ¼ C

dvC dt

CHAP. 6]

WAVEFORMS AND SIGNALS

111

Fig. 6-10 From Fig. 6-10, 8 <0 iC ðtÞ ¼ I0 ¼ 106 =T ðAÞ : 0

for t < 0 for 0 < t < T for t > T

ð32Þ

For T ¼ 1 s, I0 ¼ 106 A; for T ¼ 1 ms, I0 ¼ 103 A; and for T ¼ 1 ms, I0 ¼ 1 A. In all the preceding cases, the charge accumulated across the capacitor at the end of the transition period is ðT Q¼ iC ðtÞ dt ¼ I0 T ¼ 106 C 0

The amount of charge at t ¼ T is independent of T.

It generates a voltage vC ¼ 10 V across the capacitor.

EXAMPLE 6.18 Let dT ðt t0 Þ denote a narrow pulse of width T and height 1=T, which starts at t ¼ t0 . Consider a function f ðtÞ which is continuous between t0 and t0 þ T as shown in Fig. 6-11(a). Find the limit of integral I in (33) when T approaches zero. ð1 I¼ dT ðt t0 Þ f ðtÞ dt ð33Þ 1

dT ðt t0 Þ ¼

1=T 0

t0 < t < t0 þ T elsewhere

Substituting dT in (33) we get I¼

1 T

ð t0 þT f ðtÞ dt ¼ t0

S T

ð34aÞ

where S is the hatched area under f ðtÞ between t0 and t0 þ T in Fig. 6.11(b). Assuming T to be small, the function f ðtÞ may be approximated by a line connecting A and B. S is the area of the resulting trapezoid. S ¼ 12 ½ f ðt0 Þ þ f ðt0 þ TÞT I ¼ 12 ½ f ðt0 Þ þ f ðt0 þ TÞ As T ! 0, dT ðt t0 Þ ! ðt t0 Þ and f ðt0 þ TÞ ! f ðt0 Þ and from (34c) we get

ð34bÞ ð34cÞ

112

WAVEFORMS AND SIGNALS

[CHAP. 6

Fig. 6-11 lim I ¼ lim 12 ½ f ðt0 Þ þ f ðt0 þ TÞ

T!0

T!0

We assumed f ðtÞ to be continuous between t0 and t0 þ T.

Therefore,

lim I ¼ f ðt0 Þ

T!0 ð1

But

lim I ¼

T!0

ð34dÞ

ðt t0 Þ f ðtÞ dt

ð34eÞ (34f)

1

ð1 and so

ðt t0 Þ f ðtÞ dt ¼ f ðt0 Þ

(34g)

1

The identity (34g) is called the sifting property of the impulse function.

It is also used as another deﬁnition for

ðtÞ.

6.10

THE EXPONENTIAL FUNCTION

The function f ðtÞ ¼ est with s a complex constant is called exponential. It decays with time if the real part of s is negative and grows if the real part of s is positive. We will discuss exponentials eat in which the constant a is a real number. The inverse of the constant a has the dimension of time and is called the time constant ¼ 1=a. A decaying exponential et= is plotted versus t as shown in Fig. 6-12. The function decays from one at t ¼ 0 to zero at t ¼ 1. After seconds the function et= is reduced to e1 ¼ 0:368. For ¼ 1, the function et is called a normalized exponential which is the same as et= when plotted versus t=. EXAMPLE 6.19 Show that the tangent to the graph of et= at t ¼ 0 intersects the t axis at t ¼ as shown in Fig. 6-12. The tangent line begins at point A ðv ¼ 1; t ¼ 0Þ with a slope of det= =dtjt¼0 ¼ 1=. The equation of the line is vtan ðtÞ ¼ t= þ 1. The line intersects the t axis at point B where t ¼ . This observation provides a convenient approximate approach to plotting the exponential function as described in Example 6.20. EXAMPLE 6.20 Draw an approximate plot of vðtÞ ¼ et= for t > 0. Identify the initial point A (t ¼ 0; v ¼ 1Þ of the curve and the intersection B of its tangent with the t axis at t ¼ . Draw the tangent line AB. Two additional points C and D located at t ¼ and t ¼ 2, with heights of 0.368 and

CHAP. 6]

113

WAVEFORMS AND SIGNALS

Fig. 6-12 0.3682 ¼ 0:135, respectively, also belong to the curve. a rather good approximation (see Fig. 6-12).

Using the preceding indicators, the curve may be drawn with

EXAMPLE 6.21 (a) Show that the rate of change with respect to time of an exponential function v ¼ Aest is at any moment proportional to the value of the function at that moment. (b) Show that any linear combination of an exponential function and its n derivatives is proportional to the function itself. Find the coeﬃcient of proportionality. (a) The rate of change of a function is equal to the derivative of the function, which, for the given exponential function, is dv ¼ sAest ¼ sv dt (b) Using the result of (a) we get d nv ¼ sn Aest ¼ sn v dtn a0 v þ a1

dv d nv þ þ an n ¼ ða0 þ a1 s þ þ an sn Þv ¼ Hv dt dt

where

ð35Þ

H ¼ a0 þ a1 s þ þ an sn

(36)

f ðtÞ ¼ Aeat þ B

ð37Þ

Specifying and Plotting f ðtÞ ¼ Aeat þ B We often encounter the function

This function is completely speciﬁed by the three numbers A, B, and a deﬁned as A ¼ initial value final value

B ¼ final value

a ¼ inverse of the time constant

or, in another form, Initial value f ð0Þ ¼ A þ B

Final value f ð1Þ ¼ B

Time constant ¼ 1=a

EXAMPLE 6.22 Find a function vðtÞ which decays exponentially from 5 V at t ¼ 0 to 1 V at t ¼ 1 with a time constant of 3 s. Plot vðtÞ using the technique of Example 6.20. From (37) we have vðtÞ ¼ Aet= þ B. Now vð0Þ ¼ A þ B ¼ 5, vð1Þ ¼ B ¼ 1, A ¼ 4, and ¼ 3. Thus vðtÞ ¼ 4et=3 þ 1 The preceding result can be generalized in the following form: vðtÞ ¼ ðinitial value final valueÞet= þ ðfinal valueÞ The plot is shown in Fig. 6-13.

114

WAVEFORMS AND SIGNALS

[CHAP. 6

Fig. 6-13 EXAMPLE 6.23 The voltage v ¼ V0 ejtj= , > 0, is connected to a capacitor. Find the current i in the capacitor. Sketch v and i for V0 ¼ 10 V, C ¼ 1 mF, and ¼ 1 ms. Using i ¼ C dv=dt, for t < 0;

v ¼ V0 et=

and

i ¼ I0 et=

for t > 0;

v ¼ V0 et=

and

i ¼ I0 et=

where I0 ¼ CV0 =. For V0 ¼ 10 V, C ¼ 1 mF, and ¼ 103 s, we get I0 ¼ 10 mA. (b), respectively.

Graphs of v and i are shown in Figs. 6-14(a) and

Fig. 6-14

6.11

DAMPED SINUSOIDS A damped sinusoid, with its amplitude decaying exponentially has the form vðtÞ ¼ Aeat cos ð!t þ Þ

ð38Þ

This function will be discussed in more detail in Chapter 8. EXAMPLE 6.24 The current i ¼ I0 eat cos !t passes through a series RL circuit. (a) Find vRL , the voltage across this combination. (b) Compute vRL for I0 ¼ 3 A, a ¼ 2, ! ¼ 40 rad/s, R ¼ 5 and L ¼ 0:1 H. Sketch i as a function of time.

CHAP. 6]

WAVEFORMS AND SIGNALS

115

(a) We have

where

vR ¼ Ri ¼ RI0 eat cos !t di vL ¼ L ¼ LI0 eat ða cos !t þ ! sin !tÞ dt vRL ¼ vR þ vL ¼ I0 eat ½ðR LaÞ cos !t L! sin !t ¼ V0 eat cos ð!t þ Þ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ V0 ¼ I0 ðR LaÞ2 þ L2 !2 and ¼ tan1 ½L!=ðR LaÞ

(39)

(b) Substituting the given data into (39), V0 ¼ 18:75 V and ¼ 39:88. Current i and voltage vRL are then given by i ¼ 3e2t cos 40t

and

vRL ¼ 18:75e2t cos ð40t þ 39:88Þ

The current i is graphed in Fig. 6-15.

Fig. 6-15

6.12

RANDOM SIGNALS

So far we have dealt with signals which are completely speciﬁed. For example, the values of a sinusoidal waveform, such as the line voltage, can be determined for all times if its amplitude, frequency, and phase are known. Such signals are called deterministic. There exists another class of signals which can be speciﬁed only partly through their time averages, such as their mean, rms value, and frequency range. These are called random signals. Random signals can carry information and should not be mistaken with noise, which normally corrupts the information contents of the signal. The voltage recorded at the terminals of a microphone due to speech utterance and the signals picked up by an antenna tuned to a radio or TV station are examples of random signals. The future course and values of such signals can be predicted only in average and not precisely. Other examples of random signals are the binary waveforms in digital computers, image intensities over the area of a picture, and the speech or music which modulates the amplitude of carrier waves in an AM system. It may not seem useful to discuss signals whose values are speciﬁed only in average. However, through harmonic analysis we can still ﬁnd much about the average eﬀect of such signals in electric circuits. EXAMPLE 6.25 Samples from a random signal xðtÞ are recorded every 1 ms and designated by xðnÞ. imate the mean and rms values of xðtÞ from samples given in Table 6-2.

Approx-

116

WAVEFORMS AND SIGNALS

[CHAP. 6

Table 6-2 n

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

xðnÞ

2

4

11

5

7

6

9

10

3

6

8

4

1

3

5

12

The time averages of xðtÞ and x2 ðtÞ may be approximated from xðnÞ. Xavg ¼ ð2 þ 4 þ 11 þ 5 þ 7 þ 6 þ 9 þ 10 þ 3 þ 6 þ 8 þ 4 þ 1 þ 3 þ 5 þ 12Þ=16 ¼ 6 2 ¼ ð22 þ 42 þ 112 þ 52 þ 72 þ 62 þ 92 þ 102 þ 33 þ 62 þ 82 þ 42 þ 12 þ 32 þ 52 þ 122 Þ=16 ¼ 46 Xeff Xeff ¼ 6:78

EXAMPLE 6.26 A binary signal vðtÞ is either at 0.5 or 0:5 V. It can change its sign at 1-ms intervals. The sign change is not known a priori, but it has an equal chance for positive or negative values. Therefore, if measured for a long time, it spends an equal amount of time at the 0.5-V and 0:5-V levels. Determine its average and eﬀective values over a period of 10 s. During the 10-s period, there are 10,000 intervals, each of 1-ms duration, which on average are equally divided between the 0.5-V and 0:5-V levels. Therefore, the average of vðtÞ can be approximated as vavg ¼ ð0:5 5000 0:5 5000Þ=10,000 ¼ 0 The eﬀective value of vðtÞ is 2 ¼ ½ð0:5Þ2 5000 þ ð0:5Þ2 5000=10,000 ¼ ð0:5Þ2 Veff

or

Veff ¼ 0:5 V

The value of Veff is exact and independent of the number of intervals.

Solved Problems 6.1

Find the maximum and minimum values of v ¼ 1 þ 2 sinð!t þ Þ, given ! ¼ 1000 rad/s and ¼ 3 rad. Determine if the function v is periodic, and ﬁnd its frequency f and period T. Specify the phase angle in degrees. Vmax ¼ 1 þ 2 ¼ 3 The function v is periodic. Thus,

Vmin ¼ 1 2 ¼ 1

To ﬁnd the frequency and period, we note that ! ¼ 2f ¼ 1000 rad/s.

f ¼ 1000=2 ¼ 159:15 Hz

and

T ¼ 1=f ¼ 2=1000 ¼ 0:00628 s ¼ 6:28 ms

Phase angle ¼ 3 rad ¼ 1808 3= ¼ 171:98

6.2

In a microwave range measurement system the electromagnetic signal v1 ¼ A sin 2ft, with f ¼ 100 MHz, is transmitted and its echo v2 ðtÞ from the target is recorded. The range is computed from , the time delay between the signal and its echo. (a) Write an expression for v2 ðtÞ and compute its phase angle for time delays 1 ¼ 515 ns and 2 ¼ 555 ns. (b) Can the distance be computed unambiguously from the phase angle in v2 ðtÞ? If not, determine the additional needed information. (a) Let v2 ðtÞ ¼ B sin 2f ðt Þ ¼ B sinð2ft Þ. For f ¼ 100 MHz ¼ 108 Hz, ¼ 2f ¼ 2 108 ¼ 2k þ where 0 < < 2. For 1 ¼ 515 109 , 1 ¼ 2108 515 109 ¼ 103 ¼ 51 2 þ 1 or k1 ¼ 51 and 1 ¼ . For 2 ¼ 555 109 , 2 ¼ 2108 555 109 ¼ 111 ¼ 55 2 þ 2 or k2 ¼ 55 and 2 ¼ .

CHAP. 6]

WAVEFORMS AND SIGNALS

117

(b) Since phase angles 1 and 2 are equal, the time delays 1 and 2 may not be distinguished from each other based on the corresponding phase angles 1 and 2 . For unambiguous determination of the distance, k and are both needed.

6.3

Show that if periods T1 and T2 of two periodic functions v1 ðtÞ and v2 ðtÞ have a common multiple, the sum of the two functions, vðtÞ ¼ v1 ðtÞ þ v2 ðtÞ, is periodic with a period equal to the smallest common multiple of T1 and T2 . In such case show that Vavg ¼ V1;avg þ V2;avg . If two integers n1 and n2 can be found such that T ¼ n1 T1 ¼ n2 T2 , then v1 ðtÞ ¼ v1 ðt þ n1 T1 Þ and v2 ðtÞ ¼ v2 ðt þ n2 T2 Þ. Consequently, vðt þ TÞ ¼ v1 ðt þ TÞ þ v2 ðt þ TÞ ¼ v1 ðtÞ þ v2 ðtÞ ¼ vðtÞ and vðtÞ is periodic with period T. The average is ð ð ð 1 T 1 T 1 T ½v1 ðtÞ þ v2 ðtÞ dt ¼ v1 ðtÞ dt þ v ðtÞ dt ¼ V1;avg þ V2;avg Vavg ¼ T 0 T 0 T 0 2

6.4

Show that the average of cos2 ð!t þ Þ is 1/2. Using the identity cos2 ð!t þ Þ ¼ 12 ½1 þ cos 2ð!t þ Þ, the notation h f i ¼ Favg , and the result of Problem 6.3, we have h1 þ cos 2ð!t þ Þi ¼ h1i þ hcos 2ð!t þ Þi But hcos 2ð!t þ Þi ¼ 0.

6.5

Therefore, hcos2 ð!t þ Þi ¼ 1=2.

2 2 2 Let vðtÞ ¼ Vdc þ Vac cos ð!t þ Þ. Show that Veff ¼ Vdc þ 12 Vac .

ð 1 T ½V þ Vac cos ð!t þ Þ2 dt T 0 dc ð 1 T 2 2 ¼ ½V þ Vac cos2 ð!t þ Þ þ 2Vdc Vac cos ð!t þ Þ dt T 0 dc

2 Veff ¼

2 2 þ 12 Vac ¼ Vdc

Alternatively, we can write 2 ¼ hv2 ðtÞi ¼ h½Vdc þ Vac cos ð!t þ Þ2 i Veff 2 2 þ Vac cos2 ð!t þ Þ þ 2Vdc Vac cos ð!t þ Þi ¼ hVdc 2 2 þ Vac hcos2 ð!t þ Þi þ 2Vdc Vac hcos ð!t þ Þi ¼ Vdc 2 2 þ 12 Vac ¼ Vdc

6.6

Let f1 and f2 be two diﬀerent harmonicsqﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ of f0 . Show that the eﬀective value of ﬃ vðtÞ ¼ V1 cosð2f1 t þ 1 Þ þ V2 cos ð2f2 t þ 2 Þ is 12 ðV12 þ V22 Þ. v2 ðtÞ ¼ V12 cos2 ð2f1 t þ 1 Þ þ V22 cos2 ð2f2 t þ 2 Þ þ 2V1 V2 cos ð2f1 t þ 1 Þ cos ð2f2 t þ 2 Þ 2 ¼ hv2 ðtÞi ¼ V12 hcos2 ð2f1 t þ 1 Þi þ V22 hcos2 ð2f2 t þ 2 Þi Veff

þ 2V1 V2 hcos ð2f1 t þ 1 Þ cos ð2f2 t þ 2 Þi 2

2

But hcos ð2f1 t þ 1 Þi ¼ hcos ð2f2 t þ 2 Þi ¼ 1=2 (see Problem 6.4) and

118

WAVEFORMS AND SIGNALS

hcos ð2f1 t þ 1 Þ cos ð2f2 t þ 2 Þi ¼

2 ¼ 12 ðV12 þ V22 Þ and Veff ¼ Therefore, Veff

6.7

[CHAP. 6

1 hcos ½2ð f1 þ f2 Þt þ ð1 þ 2 Þi 2 1 þ hcos ½2ð f1 f2 Þt þ ð1 2 Þi ¼ 0 2

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 2 2 2 ðV1 þ V2 Þ:

The signal vðtÞ in Fig. 6-16 is sinusoidal. Find its period and frequency. vðtÞ ¼ A þ B cos ð!t þ Þ and ﬁnd its average and rms values.

Express it in the form

Fig. 6-16 The time between two positive peaks, T ¼ 20 s, is one period corresponding to a frequency f ¼ 0:05 Hz. The signal is a cosine function with amplitude B added to a constant value A. B ¼ 12 ðVmax Vmin Þ ¼ 12 ð8 þ 4Þ ¼ 6

A ¼ Vmax B ¼ Vmin þ B ¼ 2

The cosine is shifted by 2 s to the right, which corresponds to a phase lag of ð2=20Þ3608 ¼ 368. Therefore, the signal is expressed by t 368 vðtÞ ¼ 2 þ 6 cos 10 The average and eﬀective values are found from A and B: Vavg ¼ A ¼ 2;

6.8

2 Veff ¼ A2 þ B2 =2 ¼ 22 þ 62 =2 ¼ 22

or

Veff ¼

pﬃﬃﬃﬃﬃ 22 ¼ 4:69

Let v1 ¼ cos 200t and v2 ¼ cos 202t. Show that v ¼ v1 þ v2 is periodic. Find its period, Vmax , and the times when v attains its maximum value. The periods of v1 and v2 are T1 ¼ 1=100 s and T2 ¼ 1=101 s, respectively. The period of v ¼ v1 þ v2 is the smallest common multiple of T1 and T2 , which is T ¼ 100T1 ¼ 101T2 ¼ 1 s. The maximum of v occurs at t ¼ k with k an integer when v1 and v2 are at their maxima and Vmax ¼ 2.

6.9

Convert vðtÞ ¼ 3 cos 100t þ 4 sin 100t to A sinð100t þ Þ.

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Note that 3= 32 þ 42 ¼ 3=5 ¼ sin 36:878 and 4= 32 þ 42 ¼ 4=5 ¼ cos 36:878.

Then,

vðtÞ ¼ 3 cos 100t þ 4 sin 100t ¼ 5ð0:6 cos 100t þ 0:8 sin 100tÞ ¼ 5ðsin 36:878 cos 100t þ cos 36:878 sin 100tÞ ¼ 5 sinð100t þ 36:878Þ

CHAP. 6]

6.10

119

WAVEFORMS AND SIGNALS

Find the average and eﬀective value of v2 ðtÞ in Fig. 6-1(b) for V1 ¼ 2, V2 ¼ 1, T ¼ 4T1 . V1 T1 V2 ðT T1 Þ V1 3V2 ¼ 0:25 ¼ 4 T 2 2 pﬃﬃﬃ V T þ V2 ðT T1 Þ 7 ¼ 1 1 ¼ or V2;eff ¼ 7=2 ¼ 1:32 T 4

V2;avg ¼ 2 V2;eff

6.11

Find V3;avg and V3;eff in Fig. 6-1(c) for T ¼ 100T1 . From Fig. 6-1(c), V3;avg ¼ 0. To ﬁnd V3;eff , observe that the integral of v23 over one period is V02 T1 =2. The average of v23 over T ¼ 100T1 is therefore pﬃﬃﬃ 2 ¼ V02 T1 =200T1 ¼ V02 =200 or V3;eff ¼ V0 2=20 ¼ 0:0707V0 hv23 ðtÞ i ¼ V3;eff pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ The eﬀective value of the tone burst is reduced by the factor T=T1 ¼ 10.

6.12

Referring to Fig. 6-1(d), let T ¼ 6 and let the areas under the positive and negative sections of v4 ðtÞ be þ5 and 3, respectively. Find the average and eﬀective values of v4 ðtÞ. V4;avg ¼ ð5 3Þ=6 ¼ 1=3 The eﬀective value cannot be determined from the given data.

6.13

Find the average and eﬀective value of the half-rectiﬁed cosine wave v1 ðtÞ shown in Fig. 6-17(a). V1;avg ¼

Vm T

2 V1;eff ¼

Vm2 T

¼

Vm2 2T

2t V T 2t T=4 V ¼ m dt ¼ m sin T 2T T T=4 T=4 ð T=4 2 ð T=4 2t V 4t dt ¼ m dt cos2 1 þ cos T T 2T T=4 T=4 T 4t T=4 V2 T T V2 sin þ ¼ m tþ ¼ m 4 T T=4 2T 4 4 4 ð T=4

cos

from which V1;eff ¼ Vm =2.

6.14

Find the average and eﬀective value of the full-rectiﬁed cosine wave v2 ðtÞ ¼ Vm j cos 2t=Tj shown in Fig. 6-17(b).

Fig. 6-17 Use the results of Problems 6.3 and 6.13 to ﬁnd V2;avg . v2 ðtÞ ¼ v1 ðtÞ þ v1 ðt T=2Þ

and

Thus,

V2;avg ¼ V1;avg þ V1;avg ¼ 2V1;avg ¼ 2Vm =

Use the results of Problems 6.5 and 6.13 to ﬁnd V2;eff . 2 2 2 2 ¼ V1;eff þ V1;eff ¼ 2V1;eff ¼ Vm2 =2 V2;eff

And so, or

pﬃﬃﬃ V2;eff ¼ Vm = 2

120

WAVEFORMS AND SIGNALS

[CHAP. 6

The rms value of v2 ðtÞ can also be derived directly. Because of the squaring p operation, a full-rectiﬁed ﬃﬃﬃ cosine function has the same rms value as the cosine function itself, which is Vm = 2.

6.15

A 100-mH inductor in series with 20- resistor [Fig. 6-18(a)] carries a current i as shown in Fig. 6-18(b). Find and plot the voltages across R, L, and RL.

Fig. 6-18 8 > < 10 i ¼ 10ð1 103 tÞ ðAÞ > : 0 8 > < 200 V vR ¼ Ri ¼ 200ð1 103 tÞ ðVÞ > : 0

and

and

8 for t < 0 >0 di < 4 for 0 < t < 103 s ¼ 10 A=s dt > : 0 for t > 103 s 8 for t < 0 >0 di < vL ¼ L ¼ 1000 V for 0 < t < 103 s dt > : 0 for t > 103 s

Since the passive elements are in series, vRL ¼ vR þ vL and so

vRL

8 < 200 V ¼ 2ð105 tÞ 800 : 0

ðVÞ

for t < 0 for 0 < t < 103 s for t > 103 s

The graphs of vL and vRL are given in Fig. 6-18(c) and (d), respectively. The plot of the resistor voltage vR has the same shape as that of the current [see Fig. 6-18(b)], except for scaling by a factor of þ20.

CHAP. 6]

6.16

WAVEFORMS AND SIGNALS

121

A radar signal sðtÞ, with amplitude Vm ¼ 100 V, consists of repeated tone bursts. Each tone burst lasts Tb ¼ 50 ms. The bursts are repeated every Ts ¼ 10 ms. Find Seff and the average power in sðtÞ. pﬃﬃﬃ Let Veff ¼ Vm 2 be the eﬀective value of the sinusoid within a burst. The energy contained in a single 2 2 burst is Wb ¼ Tb Veff . The energy contained in one period of sðtÞ is Ws ¼ Ts Seff . Since Wb ¼ Ws ¼ W, we obtain pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 2 2 2 ¼ Ts Seff Seff ¼ ðTb =Ts ÞVeff Seff ¼ Tb =Ts Veff ð40Þ Tb Veff Substituting the values of Tb , Ts , and Veff into (40), we obtain qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃ Seff ¼ ð50 106 Þ=ð10 103 Þ ð100= 2Þ ¼ 5 V Then W ¼ 102 ð25Þ ¼ 0:25 J.

The average power in sðtÞ is 2 2 =Ts ¼ Seff ¼ 25 W P ¼ W=Ts ¼ Ts Seff

2 2 The average power of sðtÞ ﬃ is represented by Seff and its peak power by Veff . The ratio of peak power to pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ average power is Ts =Tb . In this example the average power and the peak power are 25 W and 5000 W, respectively.

6.17

An appliance uses Veff ¼ 120 V at 60 Hz and draws Ieff ¼ 10 A with a phase lag of 608. Express v, i, and p ¼ vi as functions of time and show that power is periodic with a dc value. Find the frequency, and the average, maximum, and minimum values of p. pﬃﬃﬃ v ¼ 120 2 cos !t

pﬃﬃﬃ i ¼ 10 2 cosð!t 608Þ

p ¼ vi ¼ 2400 cos !t cos ð!t 608Þ ¼ 1200 cos 608 þ 1200 cos ð2!t 608Þ ¼ 600 þ 1200 cos ð2!t 608Þ The power function is periodic. The frequency f ¼ 2 60 ¼ 120 Hz and Pavg ¼ 600 W, pmax ¼ 600 þ 1200 ¼ 1800 W, pmin ¼ 600 1200 ¼ 600 W.

6.18

A narrow pulse is of 1-A amplitude and 1-ms duration enters a 1-mF capacitor at t ¼ 0, as shown in Fig. 6-19. The capacitor is initially uncharged. Find the voltage across the capacitor.

Fig. 6-19 The voltage across the capacitor is 1 VC ¼ C

ðt 1

8 <0 i dt ¼ 106 t : 1V

ðVÞ

for t < 0 for 0 < t < 1 ms (charging period) for t > 1 ms

If the same amount of charge were deposited on the capacitor in zero time, then we would have v ¼ uðtÞ (V) and iðtÞ ¼ 106 ðtÞ (A).

6.19

The narrow pulse is of Problem 6.18 enters a parallel combination of a 1-mF capacitor and a 1-M resistor (Fig. 6-20). Assume the pulse ends at t ¼ 0 and that the capacitor is initially uncharged. Find the voltage across the parallel RC combination.

122

WAVEFORMS AND SIGNALS

[CHAP. 6

Fig. 6-20

Let v designate the voltage across the parallel RC combination. The current in R is iR ¼ v=R ¼ 106 v. During the pulse, iR remains negligible because v cannot exceed 1 V and iR remains under 1 mA. Therefore, it is reasonable to assume that during the pulse, iC ¼ 1 A and consequently vð0þ Þ ¼ 1 V. For t > 0, from application of KVL around the RC loop we get vþ

dv ¼ 0; dt

vð0þ Þ ¼ 1 V

ð41Þ

The only solution to (41) is v ¼ et for t > 0 or vðtÞ ¼ et uðtÞ for all t. For all practical purposes, is can be considered an impulse of size 106 A, and then v ¼ et uðtÞ (V) is called the response of the RC combination to the current impulse.

6.20

Plot the function vðtÞ which varies exponentially from 5 V at t ¼ 0 to 12 V at t ¼ 1 with a time constant of 2 s. Write the equation for vðtÞ. Identify the initial point A (t ¼ 0 and v ¼ 5Þ and the asymptote v ¼ 12 in Fig. 6-21. The tangent at A intersects the asymptote at t ¼ 2, which is point B on the line. Draw the tangent line AB. Identify point C belonging to the curve at t ¼ 2. For a more accurate plot, identify point D at t ¼ 4. Draw the curve as shown. The equation is vðtÞ ¼ Aet=2 þ B. From the initial and ﬁnal conditions, we get vð0Þ ¼ A þ B ¼ 5 and vð1Þ ¼ B ¼ 12 or A ¼ 7, and vðtÞ ¼ 7et=2 þ 12.

Fig. 6-21

6.21

The voltage v ¼ V0 eajtj for a > 0 is connected across a parallel combination of a resistor and a capacitor as shown in Fig. 6-22(a). (a) Find currents iC , iR , and i ¼ iC þ iR . (b) Compute and graph v, iC , iR , and i for V0 ¼ 10 V, C ¼ 1 mF, R ¼ 1 M, and a ¼ 1. (a) See (a) in Table 6-3 for the required currents. (b) See (b) in Table 6-3. Figures 6-22(b)–(e) show the plots of v, iC , iR , and i, respectively, for the given data. During t > 0, i ¼ 0, and the voltage source does not supply any current to the RC combination. The resistor current needed to sustain the exponential voltage across it is supplied by the capacitor.

CHAP. 6]

WAVEFORMS AND SIGNALS

Fig. 6-22

123

124

WAVEFORMS AND SIGNALS

[CHAP. 6

Table 6-3 Time

v

iC ¼ C dv=dt at

at

iR ¼ v=R

i ¼ iC þ iR at

(a)

t<0 t>0

v ¼ V0 e v ¼ V0 eat

iC ¼ CV0 ae iC ¼ CV0 aeat

iR ¼ ðV0 =RÞe iR ¼ ðV0 =RÞeat

i ¼ v0 ðCa þ 1=RÞeat i ¼ V0 ðCa þ 1=RÞeat

(b)

t<0 t>0

v ¼ 10et v ¼ 10et

iC ¼ 105 et iC ¼ 105 et

iR ¼ 105 et iR ¼ 105 et

i ¼ 2ð105 et Þ i¼0

Supplementary Problems 6.22

Let v1 ¼ 8 sin 100t and v2 ¼ 6 sin 99t. Show that v ¼ v1 þ v2 is periodic. Find the period, pﬃﬃﬃ and the maximum, average, and eﬀective values of v. Ans: T ¼ 2; Vmax ¼ 14; Vavg ¼ 0; Veff ¼ 5 2

6.23

Find period, frequency, phase angle in degrees, and maximum, minimum, average, and eﬀective values of vðtÞ ¼ 2 þ 6 cos ð10t þ =6Þ. pﬃﬃﬃﬃﬃ Ans: T ¼ 0:2 s; f ¼ 5 Hz; phase ¼ 308; Vmax ¼ 8; Vmin ¼ 4; Vavg ¼ 2; Veff ¼ 22

6.24

Reduce vðtÞ ¼ 2 cos ð!t þ 308Þ þ 3 cos !t to vðtÞ ¼ A sin ð!t þ Þ.

6.25

Find V2;avg and V2;eff in the graph of Fig. 6-1(b) for V1 ¼ V2 ¼ 3, and T ¼ 4T1 =3. Ans: V2;avg ¼ 1:5; V2;eff ¼ 3

6.26

Repeat Problem 6.25 for V1 ¼ 0, V2 ¼ 4, and T ¼ 2T1 .

6.27

Find V3;avg and V3;eff in the graph of Fig. 6-1(c) for V0 ¼ 2 and T ¼ 200T1 . Ans: V3;avg ¼ 0; V3;eff ¼ 0:1

6.28

The waveform in Fig. 6-23 is sinusoidal. Express it in the form v ¼ A p þ ﬃﬃﬃﬃﬃ B sin ð!t þ Þ and ﬁnd its mean and rms values. Ans: vðtÞ ¼ 1 þ 6 sin ðt=12 þ 1208Þ; Vavg ¼ 1; Veff ¼ 19

Fig. 6-23

Ans:

Ans:

A ¼ 4:84; ¼ 1028

pﬃﬃﬃ V2;avg ¼ 2; V2;eff ¼ 2 2

CHAP. 6]

125

WAVEFORMS AND SIGNALS

6.29

Find the average and eﬀective values of v1 ðtÞ in Fig. 6-24(a) and v2 ðtÞ in Fig. 6-24(b). rﬃﬃﬃﬃﬃ rﬃﬃﬃﬃﬃ 1 17 1 13 Ans: V1;avg ¼ ; V1;eff ¼ ; V2;avg ¼ ; V2;eff ¼ 3 3 2 2

6.30

The current through a series RL circuit with R ¼ 5 and L ¼ 10 H is given in Fig. 6-10(a) where T ¼ 1 s. Find the voltage across RL. 8 for t < 0 > <0 Ans: v ¼ 10 þ 5t for 0 < t < 1 > : 5 for t > 1

6.31

Find the capacitor current in Problem 6.19 (Fig. 6-20) for all t.

6.32

The voltage v across a 1-H inductor consists of one cycle of a sinusoidal waveform as shown in Fig. 6-25(a). (a) Write the equation for vðtÞ. (b) Find and plot the current through the inductor. (c) Find the amount and time of maximum energy in the inductor. Ans:

ðaÞ

v ¼ ½uðtÞ uðt TÞ sin

2t ðVÞ T

2t ðbÞ i ¼ ðT=2Þ½uðtÞ uðt TÞ 1 cos T 1 ðcÞ Wmax ¼ 2 T 2 ðJÞ at t ¼ T=2 2

Ans:

iC ¼ 106 ½ðtÞ et uðtÞ

ðAÞ:

See Fig. 6-25ðbÞ:

Fig. 6-24

6.33

Write the expression for vðtÞ which decays exponentially from 7 at t ¼ 0 to 3 at t ¼ 1 with a time constant of 200 ms. Ans: vðtÞ ¼ 3 þ 4e5t for t > 0

6.34

Write the expression for vðtÞ which grows exponentially with a time constant of 0.8 s from zero at t ¼ 1 to 9 at t ¼ 0. Ans: vðtÞ ¼ 9e5t=4 for t < 0

6.35

Express the current of Fig. 6-6 in terms of step functions. Ans:

iðtÞ ¼ 4uðtÞ þ 6

1 X

½uðt 5kÞ uðt 5k þ 2Þ

k¼1

6.36

In Fig. 6-10(a) let T ¼ 1 s and call the waveform s1 ðtÞ. Express s1 ðtÞ and its ﬁrst two derivatives ds1 =dt and d 2 s1 =dt2 , using step and impulse functions. Ans: s1 ðtÞ ¼ ½uðtÞ uðt 1Þt þ uðt 1Þ; ds1 =dt ¼ uðtÞ uðt 1Þ; d 2 s1 =dt2 ¼ ðtÞ ðt 1Þ

126

WAVEFORMS AND SIGNALS

[CHAP. 6

Fig. 6-25 6.37

Find an impulse voltage which creates a 1-A current jump at t ¼ 0 when applied across a 10-mH inductor. Ans: vðtÞ ¼ 102 ðtÞ (V)

6.38

(a) Given v1 ¼ cos t, v2 ¼ cos ðt þ 308Þ and v ¼ v1 þ v2 , write v in the form of a single cosine function 2 2 2 v ¼ A cosðt þ Þ. (b) Find eﬀective values of v1 , v2 , and v. Discuss why Veff > ðV1;eff þ V2;eff Þ. Ans. (a) v ¼ 1:93 cos ðt þ 158Þ; ðbÞ V1;eff ¼ V2;eff ¼ 0:707; Veff ¼ 1:366 Veff is found from the following derivation 2 ¼ hv2 i ¼ hðv1 þ v2 Þ2 i ¼ hv21 þ v22 þ 2v1 v2 i ¼ hv21 i þ hv22 i þ 2hv1 v2 i Veff

Since v1 and v2 have the same frequency and are 308 out of phase, we get hV1 V2 i ¼ 12 cos 308 ¼ 2 2 2 which is positive. Therefore, Veff > ðV1;eff þ V2;eff Þ:

6.39

6.40

pﬃﬃﬃ 3=4,

pﬃﬃﬃ pﬃﬃﬃ (a) Show that v1 ¼ cos t þ cos 2t is not periodic. (b) Replacepﬃﬃﬃ 2 by 1.4 and then show that v2 ¼ cos t þ cos 1:4t is periodic and ﬁnd pﬃﬃﬃ its period T2 . (c) Replace 2 by 1.41 and ﬁnd the period T3 of v3 ¼ cos t þ cos 1:41t. (d) Replace 2 by 1.4142 and ﬁnd the period T4 of v4 ¼ cos t þ cos 1:4142t. pﬃﬃﬃ Ans. (a) 2 is not a rational number. Therefore, v1 is not periodic. (b) T2 ¼ 10 s. (c) T3 ¼ 200 s. (d) T4 ¼ 10 000 s.

A random signal sðtÞ with an rms value of 5 V has a dc value of p 2 V. Findp the ﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ﬃﬃﬃﬃﬃ rms value of s0 ðtÞ ¼ sðtÞ 2, that is, when the dc component is removed. Ans: S0;eff ¼ 52 4 ¼ 21 ¼ 4:58 V

First-Order Circuits 7.1

INTRODUCTION

Whenever a circuit is switched from one condition to another, either by a change in the applied source or a change in the circuit elements, there is a transitional period during which the branch currents and element voltages change from their former values to new ones. This period is called the transient. After the transient has passed, the circuit is said to be in the steady state. Now, the linear diﬀerential equation that describes the circuit will have two parts to its solution, the complementary function (or the homogeneous solution) and the particular solution. The complementary function corresponds to the transient, and the particular solution to the steady state. In this chapter we will ﬁnd the response of ﬁrst-order circuits, given various initial conditions and sources. We will then develop an intuitive approach which can lead us to the same response without going through the formal solution of diﬀerential equations. We will also present and solve important issues relating to natural, force, step, and impulse responses, along with the dc steady state and the switching behavior of inductors and capacitors.

7.2

CAPACITOR DISCHARGE IN A RESISTOR

Assume a capacitor has a voltage diﬀerence V0 between its plates. When a conducting path R is provided, the stored charge travels through the capacitor from one plate to the other, establishing a current i. Thus, the capacitor voltage v is gradually reduced to zero, at which time the current also becomes zero. In the RC circuit of Fig. 7-1(a), Ri ¼ v and i ¼ C dv=dt. Eliminating i in both equations gives dv 1 þ v¼0 dt RC

ð1Þ

The only function whose linear combination with its derivative can be zero is an exponential function of the form Aest . Replacing v by Aest and dv=dt by sAest in (1), we get 1 1 st st Ae ¼ A s þ sAe þ est ¼ 0 RC RC from which

sþ

1 ¼0 RC

or

s¼

1 RC

Given vð0Þ ¼ A ¼ V0 , vðtÞ and iðtÞ are found to be 127 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

(2)

128

FIRST-ORDER CIRCUITS

vðtÞ ¼ V0 et=RC ; t>0 dv V0 t=RC ¼ e ; iðtÞ ¼ C dt R

[CHAP. 7

ð3Þ t>0

ð4Þ

The voltage and current of the capacitor are exponentials with initial values of V0 and V0 =R, respectively. As time increases, voltage and current decrease to zero with a time constant of ¼ RC. See Figs. 7-1(b) and (c). EXAMPLE 7.1 The voltage across a 1-mF capacitor is 10 V for t < 0. At t ¼ 0, a 1-M resistor is connected across the capacitor terminals. Find the time constant , the voltage vðtÞ, and its value at t ¼ 5 s. ¼ RC ¼ 106 ð106 Þ s ¼ 1 s

vðtÞ ¼ 10et ðVÞ; t > 0

vð5Þ ¼ 10e5 ¼ 0:067 V

Fig. 7-1 EXAMPLE 7.2 A 5-mF capacitor with an initial voltage of 4 V is connected to a parallel combination of a 3-k and a 6-k resistor (Fig. 7-2). Find the current i in the 6-k resistor.

Fig. 7-2

CHAP. 7]

129

FIRST-ORDER CIRCUITS

The equivalent resistance of the two parallel resistors is R ¼ 2 k. The time constant of the circuit is RC ¼ 102 s. The voltage and current in the 6-k resistor are, respectively, v ¼ 4e100t ðVÞ

7.3

and

i ¼ v=6000 ¼ 0:67e100t ðmAÞ

ESTABLISHING A DC VOLTAGE ACROSS A CAPACITOR

Connect an initially uncharged capacitor to a battery with voltage V0 through a resistor at t ¼ 0. The circuit is shown in Fig. 7-3(a).

Fig. 7-3

For t > 0, KVL around the loop gives Ri þ v ¼ V0 which, after substituting i ¼ Cðdv=dtÞ, becomes dv 1 1 þ v¼ V dt RC RC 0

t>0

ð5aÞ

with the initial condition vð0þ Þ ¼ vð0 Þ ¼ 0

ð5bÞ

The solution should satisfy both (5a) and (5b). The particular solution (or forced response) vp ðtÞ ¼ V0 satisﬁes (5a) but not (5b). The homogeneous solution (or natural response) vh ðtÞ ¼ Aet=RC can be added and its magnitude A can be adjusted so that the total solution (6a) satisﬁes both (5a) and (5b). vðtÞ ¼ vp ðtÞ þ vh ðtÞ ¼ V0 þ Aet=RC From the initial condition, vð0þ Þ ¼ V0 þ A ¼ 0 or A ¼ V0 .

Thus the total solution is

ð6aÞ

130

FIRST-ORDER CIRCUITS

vðtÞ ¼ V0 ð1 et=RC ÞuðtÞ V iðtÞ ¼ 0 et=RC uðtÞ R

[CHAP. 7

[see Fig. 7-3ðbÞ

ð6bÞ

[see Fig. 7-3ðcÞ

ð6cÞ

EXAMPLE 7.3 A 4-mF capacitor with an initial voltage of vð0 Þ ¼ 2 V is connected to a 12-V battery through a resistor R ¼ 5 k at t ¼ 0. Find the voltage across and current through the capacitor for t > 0. The time constant of the circuit is ¼ RC ¼ 0:02 s. Following the analysis of Example 7.2, we get vðtÞ ¼ 12 þ Ae50t From the initial conditions, vð0 Þ ¼ vð0þ Þ ¼ 12 þ A ¼ 2 or A ¼ 10.

Thus, for t > 0,

vðtÞ ¼ 12 10e50t ðVÞ iðtÞ ¼ ð12 vÞ=5000 ¼ 2 103 e50t A ¼ 2e50t ðmAÞ The current may also be computed from i ¼ Cðdv=dtÞ. And so the voltage increases exponentially from an initial value of 2 V to a ﬁnal value of 12 V, with a time constant of 20 ms, as shown in Fig. 7-4(a), while the current decreases from 2 mA to zero as shown in Fig. 7-4(b).

Fig. 7-4

7.4

THE SOURCE-FREE RL CIRCUIT

In the RL circuit of Fig. 7-5, assume that at t ¼ 0 the current is I0 . For t > 0, i should satisfy Ri þ Lðdi=dtÞ ¼ 0, the solution of which is i ¼ Aest . By substitution we ﬁnd A and s: AðR þ LsÞest ¼ 0;

R þ Ls ¼ 0;

s ¼ R=L

The initial condition ið0Þ ¼ A ¼ I0 . Then iðtÞ ¼ I0 eRt=L

for t > 0

ð7Þ

EXAMPLE 7.4 The 12-V battery in Fig. 7-6(a) is disconnected at t ¼ 0. for all times.

Find the inductor current and voltage v

The time constant of the circuit is L=R.

CHAP. 7]

FIRST-ORDER CIRCUITS

131

Fig. 7-5

Fig. 7-6 Assume the switch S has been closed for a long time. The inductor current is then constant and its voltage is zero. The circuit at t ¼ 0 is shown in Fig. 7-6(b) with ið0 Þ ¼ 12=4 ¼ 3 A. After the battery is disconnected, at t > 0, the circuit will be as shown in Fig. 7-6(c). For t > 0, the current decreases exponentially from 3 A to zero. The time constant of the circuit is L=R ¼ ð1=100Þ s. Using the results of Example 7.3, for t > 0, the inductor current and voltage are, respectively, iðtÞ ¼ 3e100t vðtÞ ¼ Lðdi=dtÞ ¼ 30e100t iðtÞ and vðtÞ are plotted in Figs. 7-6(d) and (e), respectively.

ðVÞ

132

7.5

FIRST-ORDER CIRCUITS

[CHAP. 7

ESTABLISHING A DC CURRENT IN AN INDUCTOR

If a dc source is suddenly applied to a series RL circuit initially at rest, as in Fig. 7-7(a), the current grows exponentially from zero to a constant value with a time constant of L=R. The preceding result is the solution of the ﬁrst-order diﬀerential equation (8) which is obtained by applying KVL around the loop. The solution follows.

Fig. 7-7

Ri þ L

di ¼ V0 dt

ið0þ Þ ¼ 0

for t > 0;

ð8Þ

Since i ¼ ih ðtÞ þ ip ðtÞ, where ih ðtÞ ¼ AeRt=L and ip ðtÞ ¼ V0 =R, we have i ¼ AeRt=L þ V0 =R The coeﬃcient A is found from ið0þ Þ ¼ A þ V0 =R ¼ 0 or A ¼ V0 =R. The current in the inductor and the voltage across it are given by (9) and (10) and plotted in Fig. 7-7(b) and (c), respectively. iðtÞ ¼ V0 =Rð1 eRt=L Þ di vðtÞ ¼ L ¼ V0 eRt=L dt

7.6

for t > 0

ð9Þ

for t > 0

ð10Þ

THE EXPONENTIAL FUNCTION REVISITED

The exponential decay function may be written in the form et= , where is the time constant (in s). For the RC circuit of Section 7.2, ¼ RC; while for the RL circuit of Section 7.4, ¼ L=R. The general decay function f ðtÞ ¼ Aet=

ðt > 0Þ

is plotted in Fig. 7-8, with time measured in multiples of .

It is seen that

f ðÞ ¼ Ae1 ¼ 0:368A

CHAP. 7]

FIRST-ORDER CIRCUITS

133

Fig. 7-8

that is, at t ¼ the function is 36.8 percent of the initial value. It may also be said that the function has undergone 63.2 percent of the change from f ð0þ Þ to f ð1Þ. At t ¼ 5, the function has the value 0.0067A, which is less than 1 percent of the initial value. From a practical standpoint, the transient is often regarded as over after t ¼ 5. The tangent to the exponential curve at t ¼ 0þ can be used to estimate the time constant. In fact, since slope ¼ f 0 ð0þ Þ ¼

A

the tangent line must cut the horizontal axis at t ¼ (see Fig. 7-9). More generally, the tangent at t ¼ t0 has horizontal intercept t0 þ . Thus, if the two values f ðt0 Þ and f 0 ðt0 Þ are known, the entire curve can be constructed.

Fig. 7-9

At times a transient is only partially displayed (on chart paper or on the face of an oscilloscope), and the simultaneous values of function and slope needed in the preceding method are not available. In that case, any pair of data points, perhaps read from instruments, may be used to ﬁnd the equation of the transient. Thus, referring to Fig. 7-10, f1 ¼ Aet1 =

f2 ¼ Aet2 =

which may be solved simultaneously to give ¼ and then A in terms of and either f1 or f2 .

t2 t1 ln f1 ln f2

134

FIRST-ORDER CIRCUITS

[CHAP. 7

Fig. 7-10

7.7

COMPLEX FIRST-ORDER RL AND RC CIRCUITS

A more complex circuit containing resistors, sources, and a single energy storage element may be converted to a The´venin or Norton equivalent as seen from the two terminals of the inductor or capacitor. This reduces the complex circuit to a simple RC or RL circuit which may be solved according to the methods described in the previous sections. If a source in the circuit is suddently switched to a dc value, the resulting currents and voltages are exponentials, sharing the same time constant with possibly diﬀerent initial and ﬁnal values. The time constant of the circuit is either RC or L=R, where R is the resistance in the The´venin equivalent of the circuit as seen by the capacitor or inductor. EXAMPLE 7.5 Find i, v, and i1 in Fig. 7-11(a).

Fig. 7-11 The The´venin equivalent of the circuit to the left of the inductor is shown in Fig. 7-11(b) with RTh ¼ 4 and vTh ¼ 3uðtÞ (V). The time constant of the circuit is ¼ L=RTh ¼ 5ð103 Þ=4 s ¼ 1:25 ms. The initial value of the inductor current is zero. Its ﬁnal value is ið1Þ ¼

vTh 3V ¼ ¼ 0:75 A RTh 4

Therefore, i ¼ 0:75ð1 e800t ÞuðtÞ

ðAÞ

v¼L

di ¼ 3e800t uðtÞ dt

ðVÞ

i1 ¼

9v 1 ¼ ð3 e800t ÞuðtÞ ðAÞ 12 4

v can also be derived directly from its initial value vð0þ Þ ¼ ð9 6Þ=ð12 þ 6Þ ¼ 3 V, its ﬁnal value vð1Þ ¼ 0 and the circuit’s time constant.

CHAP. 7]

135

FIRST-ORDER CIRCUITS

EXAMPLE 7.6 In Fig. 7-12 the 9-mF capacitor is connected to the circuit at t ¼ 0. is v0 ¼ 17 V. Find vA , vB , vC , iAB , iAC , and iBC for t > 0:

At this time, capacitor voltage

Fig. 7-12 Apply KCL at nodes A, B, and C for t > 0 to ﬁnd voltages in term of i: 1 1 1 1 1 or 6vA 3vB vC ¼ 0 þ þ vA vB vC ¼ 0 Node A: 2 3 6 2 6 1 1 1 1 þ v 103 i vC ¼ 0 or 2vA þ 3vB vC ¼ ð4 103 Þi Node B: vA þ 2 2 4 B 4 1 1 1 1 1 or 2vA 3vB þ 6vC ¼ 0 Node C: vA vB þ þ þ v ¼0 6 4 4 6 12 C

(11) (12) (13)

Solving (11), (12), and (13) simultaneously, vA ¼ 73 ð103 Þi

3 vB ¼ 34 9 ð10 Þi

vC ¼ 83 ð103 Þi

The circuit as seen by the capacitor is equivalent to a resistor R ¼ vB =i ¼ 34=9 k. The capacitor discharges 3 6 its initial voltage V0 in an exponential form with a time constant ¼ RC ¼ 34 9 ð10 Þð9 10 Þ ¼ 0:034 s. For t > 0, the voltages and currents are vB ¼ V0 et= ¼ 17e1000t=34 i ¼ C

ðVÞ

dvB ¼ ð9 17 103 =34Þe1000t=34 ¼ ð4:5 103 Þe1000t=34 dt

vA ¼ 73 ð103 Þi ¼ 10:5e1000t=34

vC ¼ 83 ð103 Þi ¼ 12e1000t=34

ðVÞ

ðAÞ ðVÞ

vAB ¼ vA vB ¼ 6:5e1000t=34

ðVÞ

iAB ¼ vAB =2000 ¼ ð3:25 103 Þe1000t=34

ðAÞ

1000t=34

ðVÞ

iAC ¼ vAC =6000 ¼ ð0:25 103 Þe1000t=34

ðAÞ

vAC ¼ vA vC ¼ 1:5e

1000t=34

vBC ¼ vB vC ¼ 5e

3

1000t=34

iBC ¼ vBC =4000 ¼ ð1:25 10 Þe

ðVÞ

ðAÞ

All voltages and currents are exponential functions and have the same time constant. For simplicity, it is customary to use units of V, mA, k, and ms for voltage, current, resistance, and time, respectively, so that the multipliers 1000 and 103 can be omitted from the equations as summarized below. vA ¼ 10:5et=34 t=34

vB ¼ 17e

t=34

vC ¼ 12e

t=34

i ¼ 4:5e

ðVÞ ðVÞ ðVÞ ðmAÞ

vAB ¼ 6:5et=34 t=34

vAC ¼ 1:5e

t=34

vBC ¼ 5e

ðVÞ

ðVÞ

iAB ¼ 3:25et=34

ðmAÞ

ðVÞ

t=34

ðmAÞ

iAC ¼ 0:25e

t=34

iBC ¼ 1:25e

ðmAÞ

136

7.8

FIRST-ORDER CIRCUITS

[CHAP. 7

DC STEADY STATE IN INDUCTORS AND CAPACITORS

As noted in Section 7.1, the natural exponential component of the response of RL and RC circuits to step inputs diminishes as time passes. At t ¼ 1, the circuit reaches steady state and the response is made of the forced dc component only. Theoretically, it should take an inﬁnite amount of time for RL or RC circuits to reach dc steady state. However, at t ¼ 5, the transient component is reduced to 0.67 percent of its initial value. After passage of 10 time constants the transient component equals to 0.0045 percent of its initial value, which is less than 5 in 100,000, at which time for all practical purposes we may assume the steady state has been reached. At the dc steady state of RLC circuits, assuming no sustained oscillations exist in the circuit, all currents and voltages in the circuit are constants. When the voltage across a capacitor is constant, the current through it is zero. All capacitors, therefore, appear as open circuits in the dc steady state. Similarly, when the current through an inductor is constant, the voltage across it is zero. All inductors therefore appear as short circuits in the dc steady state. The circuit will be reduced to a dc-resistive case from which voltages across capacitors and currents through inductors can be easily found, as all the currents and voltages are constants and the analysis involves no diﬀerential equations. The dc steady-state behavior presented in the preceding paragraph is valid for circuits containing any number of inductors, capacitors, and dc sources. EXAMPLE 7.7 Find the steady-state values of iL , vC1 , and vC2 in the circuit of Fig. 7-13(a). When the steady state is reached, the circuit will be as shown in Fig. 7-13(b). The inductor current and capacitor voltages are obtained by applying KCL at nodes A and B in Fig. 7-13(b). Thus, vA vA vB vA þ 18 vB þ þ ¼3 3 6 6

Node A:

vB vB vA vB 18 vA þ þ ¼0 12 6 6

Node B:

or or

2vA vB ¼ 0 4vA þ 5vB ¼ 36

Solving for vA and vB we ﬁnd vA ¼ 6 V and vB ¼ 12 V. By inspection of Fig. 7-13(b), we have iL ¼ 2 mA, vC1 ¼ 8 V, and vC2 ¼ 6 V. EXAMPLE 7.8 Find i and v in the circuit of Fig. 7-14. At t ¼ 0, the voltage across the capacitor is zero. Its ﬁnal value is obtained from dc analysis to be 2 V. The time constant of the circuit of Fig. 7-14, as derived in Example 7.6, is 0.034 s. Therefore, v ¼ 2ð1 e1000t=34 ÞuðtÞ 6

i¼C

7.9

ðVÞ

3

dv ð9 10 Þð2 10 Þ 1000t=34 ¼ e uðtÞ dt 34

ðAÞ ¼ 0:53e1000t=34 uðtÞ

ðmAÞ

TRANSITIONS AT SWITCHING TIME

A sudden switching of a source or a jump in its magnitude can translate into sudden jumps in voltages or currents in a circuit. A jump in the capacitor voltage requires an impulse current. Similarly, a jump in the inductor current requires an impulse voltage. If no such impulses can be present, the capacitor voltages and the inductor currents remain continuous. Therefore, the post-switching conditions of L and C can be derived from their pre-switching conditions. EXAMPLE 7.9 In Fig. 7-15(a) the switch S is closed at t ¼ 0. Find i and v for all times. At t ¼ 0 , the circuit is at steady state and the inductor functions as a short with vð0 Þ ¼ 0 [see Fig. 7-15(b)]. The inductor current is then easily found to be ið0 Þ ¼ 2 A. After S is closed at t ¼ 0, the circuit will be as shown in Fig. 7-15(c). For t > 0, the current is exponential with a time constant of ¼ L=R ¼ 1=30 s, an initial value of ið0þ Þ ¼ ið0 Þ ¼ 2 A, and a ﬁnal value of 12=3 ¼ 4 A. The inductor’s voltage and current are

CHAP. 7]

FIRST-ORDER CIRCUITS

137

Fig. 7-13

Fig. 7-14 For t < 0;

i ¼ 2 A and v ¼ 0

For t > 0;

i ¼ 4 2e30t

ðAÞ and v ¼ L

di ¼ 6e30t dt

ðVÞ

and plotted in Figs. 7-15(d) and (e).

EXAMPLE 7.10

Find i and v for t ¼ 0 and t ¼ 0þ in the circuit of Fig. 7-16, given R ¼ 5 , L ¼ 10 mH, and 5 V for t < 0 vs ¼ 5 sin !t ðVÞ for t > 0

138

FIRST-ORDER CIRCUITS

[CHAP. 7

Fig. 7-15

Fig. 7-16

At t ¼ 0 , ið0 Þ ¼ 5=5 ¼ 1 A and vð0 Þ ¼ 0. During the transition time t ¼ 0 to t ¼ 0þ , the inductor current is continuous as there exists no voltage impulse to produce a discontinuity in it. Therefore, ið0þ Þ ¼ ið0 Þ ¼ 1 A. To ﬁnd vð0þ Þ, write KVL at t ¼ 0þ : vs ¼ RI þ v and note that vs ð0þ Þ ¼ 0. Therefore, vð0þ Þ ¼ vs ð0þ Þ rið0þ Þ ¼ 5 V.

CHAP. 7]

7.10

FIRST-ORDER CIRCUITS

139

RESPONSE OF FIRST-ORDER CIRCUITS TO A PULSE

In this section we will derive the response of a ﬁrst-order circuit to a rectangular pulse. The derivation applies to RC or RL circuits where the input can be a current or a voltage. As an example, we use the series RC circuit in Fig. 7-17(a) with the voltage source delivering a pulse of duration T and height V0 . For t < 0, v and i are zero. For the duration of the pulse, we use (6b) and (6c) in Section 7.3: v ¼ V0 ð1 et=RC Þ V i ¼ 0 et=RC R

ð0 < t < TÞ

ð14aÞ

ð0 < t < TÞ

ð14bÞ

When the pulse ceases, the circuit is source-free with the capacitor at an initial voltage VT . VT ¼ V0 ð1 eT=RC Þ

ð14cÞ

Using (3) and (4) in Section 7.2, and taking into account the time shift T, we have v ¼ VT eðtTÞ=RC i ¼ ðVT =RÞe

ðtTÞ=RC

ðt > TÞ

ð15aÞ

ðt > TÞ

ð15bÞ

The capacitor voltage and current are plotted in Figs. 7-17(b) and (c).

Fig. 7-17

EXAMPLE 7.11 In the circuit of Fig. 7-17(a), let R ¼ 1 k and C ¼ 1 mF and let the voltage source be a pulse of height V0 and duration T. Find i and v for (a) V0 ¼ 1 V and T ¼ 1 ms, (b) V0 ¼ 10 V and T ¼ 0:1 ms, and (c) V0 ¼ 100 V and T ¼ 0:01 ms. We use (14) and (15) with the time constant of ¼ RC ¼ 1 ms. For convenience, time will be expressed in ms, voltages in V, and currents in mA. We also use the approximation et ¼ 1 t when t 1. (a) V0 ¼ 1 V, T ¼ 1 ms. For 0 < t < 1 ms, v ¼ ð1 et Þ; i ¼ et , and VT ¼ ð1 e1 Þ ¼ 0:632 V

140

FIRST-ORDER CIRCUITS

[CHAP. 7

For t > 1 ms, v ¼ 0:632eðt1Þ ¼ 1:72et , and i ¼ 1:72et (b) V0 ¼ 10 V, T ¼ 0:1 ms. For 0 < t < 0:1 ms, v ¼ 10ð1 et Þ; i ¼ 10et , and VT ¼ 10ð1 e0:1 Þ ¼ 0:95 V For t > 0:1 ms, v ¼ 0:95eðt0:1Þ ¼ 1:05et , and i ¼ 1:05et (c)

V0 ¼ 100 V, T ¼ 0:01 ms. For 0 < t < 0:01 ms, v ¼ 100ð1 et Þ 100t; i ¼ 100et 100ð1 tÞ, and VT ¼ 100ð1 e0:01 Þ ¼ 0:995 V For t > 0:01 ms, v ¼ 0:995eðt0:01Þ ¼ 1:01et and i ¼ 1:01et

As the input voltage pulse approaches an impulse, the capacitor voltage and current approach v ¼ et uðtÞ (V) and i ¼ ðtÞ et uðtÞ.

7.11

IMPULSE RESPONSE OF RC AND RL CIRCUITS

A narrow pulse can be modeled as an impulse with the area under the pulse indicating its strength. Impulse response is a useful tool in analysis and synthesis of circuits. It may be derived in several ways: take the limit of the response to a narrow pulse, to be called limit approach, as illustrated in Examples 7-11 and 7-12; take the derivative of the step response; solve the diﬀerential equation directly. The impulse response is often designated by hðtÞ. EXAMPLE 7.12 Find the limits of i and v of the circuit Fig. 7-17(a) for a voltage pulse of unit area as the pulse duration is decreased to zero. We use the pulse responses in (14) and (15) with V0 ¼ 1=T and ﬁnd their limits as T approaches zero. From (14c) we have lim VT ¼ lim ð1 eT=RC Þ=T ¼ 1=RC

T!0

T!0

From (15) we have: For t < 0;

hv ¼ 0

and hi ¼ 0 1 1 and hi ¼ ðtÞ 0 hv RC R 1 t=RC 1 hv ðtÞ ¼ and hi ðtÞ ¼ 2 et=RC e RC R C

þ

For 0 < t < 0 ; For t > 0; Therefore, hv ðtÞ ¼

1 t=RC uðtÞ e RC

and

hi ðtÞ ¼

1 1 ðtÞ 2 et=RC uðtÞ R R C

EXAMPLE 7.13 Find the impulse responses of the RC circuit in Fig. 7-17(a) by taking the derivatives of its unit step responses. A unit impulse may be considered the derivative of a unit step. Based on the properties of linear diﬀerential equations with constant coeﬃcients, we can take the time derivative of the step response to ﬁnd the impulse response. The unit step responses of an RC circuit were found in (6) to be vðtÞ ¼ ð1 et=RC ÞuðtÞ

and

iðtÞ ¼ ð1=RÞet=RC uðtÞ

We ﬁnd the unit impulse responses by taking the derivatives of the step responses.

Thus

CHAP. 7]

141

FIRST-ORDER CIRCUITS

hv ðtÞ ¼

1 t=RC uðtÞ e RC

and

hi ðtÞ ¼

1 1 ðtÞ 2 et=RC uðtÞ R R C

EXAMPLE 7.14 Find the impulse responses hi ðtÞ; hv ðtÞ; and hi1 ðtÞ of the RL circuit of Fig. 7-11(a) by taking the derivatives of its unit step responses. The responses of the circuit to a step of amplitude 9 were already found in Example 7.5. Taking their derivatives and scaling them down by 1/9, we ﬁnd the unit impulse responses to be 1 9 1 hv ðtÞ ¼ 9 1 hi1 ðtÞ ¼ 9 hi ðtÞ ¼

7.12

d 200 800t uðtÞ ½0:75ð1 e800t ÞuðtÞ ¼ e dt 3 d 800 800t 1 ½3e800t uðtÞ ¼ e uðtÞ þ ðtÞ dt 3 3 d 1 200 800t 1 800t ð3 e e ðtÞ ÞuðtÞ ¼ uðtÞ þ dt 4 9 18

SUMMARY OF STEP AND IMPULSE RESPONSES IN RC AND RL CIRCUITS

Responses of RL and RC circuits to step and impulse inputs are summarized in Table 7-1. Some of the entries in this table have been derived in the previous sections. The remaining entries will be derived in the solved problems.

7.13

RESPONSE OF RC AND RL CIRCUITS TO SUDDEN EXPONENTIAL EXCITATIONS

Consider the ﬁrst-order diﬀerential equation which is derived from an RL combination in series with a sudden exponential voltage source vs ¼ V0 est uðtÞ as in the circuit of Fig. 7-18. The circuit is at rest for t < 0. By applying KVL, we get Ri þ L

di ¼ V0 est uðtÞ dt

ð16Þ

For t > 0, the solution is iðtÞ ¼ ih ðtÞ þ ip ðtÞ

and

ið0þ Þ ¼ 0

Table 7-1(a) Step and Impulse Responses in RC Circuits RC circuit

Unit Step Response

vs ¼ uðtÞ ( v ¼ ð1 et=Rc ÞuðtÞ i ¼ ð1=RÞet=Rc uðtÞ

is ¼ uðtÞ ( v ¼ Rð1 et=RC ÞuðtÞ i ¼ et=RC uðtÞ

Unit Impulse Response

vs ¼ ðtÞ ( hv ¼ ð1=RCÞet=RC uðtÞ hi ¼ ð1=R2 CÞet=RC uðtÞ þ ð1=RÞðtÞ

is ¼ ðtÞ ( hv ¼ ð1=CÞet=RC uðtÞ hi ¼ ð1=RCÞet=RC uðtÞ þ ðtÞ

ð17aÞ

142

FIRST-ORDER CIRCUITS

[CHAP. 7

Table 7-1(b) Step and Impulse Responses in RL Circuits RL circuit

Unit Step Response

Unit Impulse Response

vs ¼ uðtÞ ( v ¼ eRt=L uðtÞ i ¼ ð1=RÞð1 eRt=L ÞuðtÞ

vs ¼ ðtÞ ( hv ¼ ðR=LÞeRt=L uðtÞ þ ðtÞ hi ¼ ð1=LÞeRt=L uðtÞ

is ¼ uðtÞ ( v ¼ ReRt=L uðtÞ

is ¼ ðtÞ ( hv ¼ ðR2 =LÞeRt=L uðtÞ þ RðtÞ

i ¼ ð1 eRt=L ÞuðtÞ

hi ¼ ðR=LÞeRt=L uðtÞ

Fig. 7-18

The natural response ih ðtÞ is the solution of Ri þ Lðdi=dtÞ ¼ 0; i.e., the case with a zero forcing function. Following an argument similar to that of Section 7.4 we obtain ih ðtÞ ¼ AeRt=L

ð17bÞ

The forced response ip ðtÞ is a function which satisﬁes (16) for t > 0.

The only such function is

ip ðtÞ ¼ I0 est After substituting ip in (16), I0 is found to be I0 ¼ V0 =ðR þ LsÞ. boundary condition ið0þ Þ ¼ 0 is also satisﬁed. Therefore, iðtÞ ¼

ð17cÞ By choosing A ¼ V0 = ðR þ LsÞ, the

V0 ðest eRt=L ÞuðtÞ R þ Ls

ð17dÞ

Special Case. If the forcing function has the same exponent as that of the natural response ðs ¼ R=LÞ, the forced response needs to be ip ðtÞ ¼ I0 teRt=L . This can be veriﬁed by substitution in (16), which also yields I0 ¼ V0 =L The natural response is the same as (17b). The total response is then iðtÞ ¼ ip ðtÞ þ ih ðtÞ ¼ ðI0 t þ AÞeRt=L From ið0 Þ ¼ ið0þ Þ ¼ 0 we ﬁnd A ¼ 0, and so iðtÞ ¼ I0 teLt=R uðtÞ, where I0 ¼ V0 =L.

CHAP. 7]

143

FIRST-ORDER CIRCUITS

RESPONSE OF RC AND RL CIRCUITS TO SUDDEN SINUSOIDAL EXCITATIONS

7.14

When a series RL circuit is connected to a sudden ac voltage vs ¼ V0 cos !t (Fig. 7-19), the equation of interest is Ri þ L

di ¼ V0 ðcos !tÞuðtÞ dt

ð18Þ

The solution is iðtÞ ¼ ih þ ip

where

ih ðtÞ ¼ AeRt=L

and

ip ðtÞ ¼ I0 cos ð!t Þ

By inserting ip in (18), we ﬁnd I0 : V0 ﬃ I0 ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ R2 þ L2 !2 Then

and

¼ tan1

iðtÞ ¼ AeRt=L þ I0 cos ð!t Þ

L! R

t>0

From ið0þ Þ ¼ 0, we get A ¼ I0 cos . Therefore, iðtÞ ¼ I0 ½cos ð!t Þ cos ðeRt=L Þ

Fig. 7-19

7.15

SUMMARY OF FORCED RESPONSE IN FIRST-ORDER CIRCUITS Consider the following diﬀerential equation: dv ðtÞ þ avðtÞ ¼ f ðtÞ dt

ð19Þ

The forced response vp ðtÞ depends on the forcing function f ðtÞ. Several examples were given in the previous sections. Table 7-2 summarizes some useful pairs of the forcing function and what should be guessed for vp ðtÞ. The responses are obtained by substitution in the diﬀerential equation. By weighted linear combination of the entries in Table 7-2 and their time delay, the forced response to new functions may be deduced.

7.16

FIRST-ORDER ACTIVE CIRCUITS

Active circuits containing op amps are less susceptible to loading eﬀects when interconnected with other circuits. In addition, they oﬀer a wider range of capabilities with more ease of realization than passive circuits. In our present analysis of linear active circuits we assume ideal op amps; that is; (1) the current drawn by the op amp input terminals is zero and (2) the voltage diﬀerence between the inverting and noninverting terminals of the op amp is negligible (see Chapter 5). The usual methods of analysis are then applied to the circuit as illustrated in the following examples.

144

FIRST-ORDER CIRCUITS

[CHAP. 7

Table 7-2 f ðtÞ

vp ðtÞ

1

1 a

t

t 1 a a2

est ; ðs 6¼ aÞ

est sþa

eat

teat

cos !t

A cos ð!t Þ

ebt cos !t

1 A ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 a þ !2

where

Aebt cos ð!t Þ

where

and

tan ¼

1 A ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ða bÞ2 þ !2

and

! a tan ¼

! ab

EXAMPLE 7.15 Highpass ﬁlter. The op amp in the circuit of Fig. 7-44 is ideal. Find the unit-step response of the circuit; that is, v2 for v1 ¼ uðtÞ: The inverting input terminal of the op amp is at virtual ground and the capacitor has zero voltage at t ¼ 0þ . The 1-V step input therefore generates an exponentially decaying current i through R1 C (from left to right, with a time constant R1 C and initial value of 1=R1 ). i¼

1 t=ðR1 CÞ e uðtÞ R1

All of the preceding current passes through R2 (the op amp draws no current), generating v2 ¼ R2 i at the output terminal. The unit-step response is therefore v2 ¼

R2 t=ðR1 CÞ e uðtÞ R1

EXAMPLE 7.16 In the circuit of Fig. 7-44 derive the diﬀerential equation relating v2 to v1 . Find its unit-step response and compare with the answer in Example 7.15. Since the inverting input terminal of the op amp is at virtual ground and doesn’t draw any current, the current i passing through C, R1 , and R2 from left to right is v2 =R2 . Let vA be the voltage of the node connecting R1 and C. Then, the capacitor voltage is v1 vA (positive on the left side). The capacitor current and voltage are related by

v2 dðv1 vA Þ ¼ R2 dt

To eliminate vA , we note that the segment made of R1 , R2 , and the op amp form an inverting ampliﬁer with v2 ¼ ðR2 =R1 ÞvA , from which vA ¼ ðR1 =R2 Þv2 . Substituting for vA , we get v2 þ R 1 C

dv2 dv ¼ R2 C 1 dt dt

To ﬁnd the unit-step response, we ﬁrst solve the following equation: dv R2 C t>0 v2 þ R 1 C 2 ¼ 0 t<0 dt The solution of the preceding equation is R2 Cð1 et=ðR1 CÞ ÞuðtÞ. derivative of the preceding solution.

The unit-step response of the circuit is the time-

CHAP. 7]

145

FIRST-ORDER CIRCUITS

v2 ðtÞ ¼

R2 t=ðR1 CÞ e uðtÞ R1

Alternate Approach The unit step response may also be found by the Laplace transform method (see Chapter 16). EXAMPLE 7.17 Passive phase shifter. Find the relationship between v2 and v1 in the circuit of Fig. 7-45(a). Let node D be the reference node. Apply KCL at nodes A and B to ﬁnd KCL at node A: KCL at node B:

dvA ðvA v1 Þ ¼0 þ R dt dðvB v1 Þ vB C þ ¼0 dt R

C

Subtracting the second equation from the ﬁrst and noting that v2 ¼ vA vB we get v2 þ RC

dv2 dv ¼ v1 RC 1 dt dt

EXAMPLE 7.18 Active phase shifter. Show that the relationship between v2 and v1 in the circuit of Fig. 7-45(b) is the same as in Fig. 7-45(a). Apply KCL at the inverting (node A) and non-inverting (node B) inputs of the op amp. ðvA v1 Þ ðvA v2 Þ þ ¼0 R1 R1 ðvB v1 Þ dv þC B ¼0 R dt

KCL at node A: KCL at node B:

From the op amp we have vA ¼ vB and from the KCL equation for node A, we have vA ¼ ðv1 þ v2 Þ=2. the preceding values in the KCL at node B, we ﬁnd v2 þ RC

Substituting

dv2 dv ¼ v1 RC 1 dt dt

Solved Problems 7.1

At t ¼ 0 , just before the switch is closed in Fig. 7-20, vC ¼ 100 V. charge transients.

Obtain the current and

Fig. 7-20 With the polarities as indicated on the diagram, vR ¼ vC for t > 0, and 1=RC ¼ 62:5 s1 . vC ð0þ Þ ¼ vC ð0 Þ ¼ 100 V. Thus, vR ¼ vC ¼ 100e62:5t

ðVÞ

i¼

vR ¼ 0:25e62:5t R

ðAÞ

q ¼ CvC ¼ 4000e62:5t

ðmCÞ

Also,

146

7.2

FIRST-ORDER CIRCUITS

[CHAP. 7

In Problem 7.1, obtain the power and energy in the resistor, and compare the latter with the initial energy stored in the capacitor. pR ¼ vR i ¼ 25e125t ðWÞ ðt ðt wR ¼ pR dt ¼ 25e125t dt ¼ 0:20ð1 e125t Þ 0

ðJÞ

0

The initial stored energy is W0 ¼ 12 CV02 ¼ 12 ð40 106 Þð100Þ2 J ¼ 0:20 ¼ wR ð1Þ In other words, all the stored energy in the capacitor is eventually delivered to the resistor, where it is converted into heat.

7.3

An RC transient identical to that in Problems 7.1 and 7.2 has a power transient pR ¼ 360et=0:00001

ðWÞ

Obtain the initial charge Q0 , if R ¼ 10 . 2 ¼ 105 pR ¼ P0 e2t=RC or or C ¼ 2 mF RC ðt wR ¼ pR dt ¼ 3:6ð1 et=0:00001 Þ ðmJÞ 0

Then, wR ð1Þ ¼ 3:6 mJ ¼

7.4

Q20 =2C,

from which Q0 ¼ 120 mC.

The switch in the RL circuit shown in Fig. 7-21 is moved from position 1 to position 2 at t ¼ 0. Obtain vR and vL with polarities as indicated.

Fig. 7-21 The constant-current source drives a current through the inductance in the same direction as that of the transient current i. Then, for t > 0, i ¼ I0 eRt=L ¼ 2e25t 25t

vR ¼ Ri ¼ 200e

ðAÞ

ðVÞ 25t

vL ¼ vR ¼ 200e

7.5

ðVÞ

For the transient of Problem 7.4 obtain pR and pL . pR ¼ vR i ¼ 400e50t 50t

pL ¼ vL i ¼ 400e

ðWÞ ðWÞ

Negative power for the inductance is consistent with the fact that energy is leaving the element. this energy is being transferred to the resistance, pR is positive.

And, since

CHAP. 7]

7.6

147

FIRST-ORDER CIRCUITS

A series RC circuit with R ¼ 5 k and C ¼ 20 mF has a constant-voltage source of 100 V applied at t ¼ 0; there is no initial charge on the capacitor. Obtain i, vR , vC , and q, for t > 0. The capacitor charge, and hence vC , must be continuous at t ¼ 0: vC ð0þ Þ ¼ vC ð0 Þ ¼ 0 As t ! 1, vC ! 100 V, the applied voltage. from Section 6.10,

The time constant of the circuit is ¼ RC ¼ 101 s.

Hence,

vC ¼ ½vC ð0þ Þ vC ð1Þet= þ vC ð1Þ ¼ 100e10t þ 100 ðVÞ The other functions follow from this. enters, vR þ vC ¼ 100 V, and so

If the element voltages are both positive where the current

vR ¼ 100e10t ðVÞ v i ¼ R ¼ 20e10t ðmAÞ R q ¼ CvC ¼ 2000ð1 e10t Þ

7.7

ðmCÞ

The switch in the circuit shown in Fig. 7-22(a) is closed at t ¼ 0, at which moment the capacitor has charge Q0 ¼ 500 mC, with the polarity indicated. Obtain i and q, for t > 0, and sketch the graph of q.

Fig. 7-22 The initial charge has a corresponding voltage V0 ¼ Q0 =C ¼ 25 V, whence vC ð0þ Þ ¼ 25 V. The sign is negative because the capacitor voltage, in agreement with the positive direction of the current, would be þ on the top plate. Also vC ð1Þ ¼ þ50 V and ¼ 0:02 s. Thus, as in Problem 7.6, vC ¼ 75e50t þ 50 ðVÞ from which q ¼ CvC ¼ 1500e50t þ 1000 ðmCÞ

i¼

dq ¼ 75e50t dt

ðmAÞ

The sketch in Fig. 7-22(b) shows that the charge changes from 500 mC of one polarity to 1000 mC of the opposite polarity.

7.8

Obtain the current i, for all values of t, in the circuit of Fig. 7-23. For t < 0, the voltage source is a short circuit and the current source shares 2 A equally between the two 10- resistors:

148

FIRST-ORDER CIRCUITS

[CHAP. 7

Fig. 7-23 iðtÞ ¼ ið0 Þ ¼ ið0þ Þ ¼ 1 A For t > 0, the current source is replaced by an open circuit and the 50-V source acts in the RL series circuit ðR ¼ 20 Þ. Consequently, as t ! 1, i ! 50=20 ¼ 2:5 A. Then, by Sections 6.10 and 7.3, iðtÞ ¼ ½ðið0þ Þ ið1ÞeRt=L þ ið1Þ ¼ 3:5e100t 2:5 ðAÞ By means of unit step functions, the two formulas may be combined into a single formula valid for all t: iðtÞ ¼ uðtÞ þ ð3:5e100t 2:5ÞuðtÞ

7.9

In Fig. 7-24(a), the switch is closed at t ¼ 0. vC , and vs for all times if is ¼ 2 mA.

ðAÞ

The capacitor has no charge for t < 0.

Find iR , iC ,

For t < 0, iR ¼ 2 mA, iC ¼ vC ¼ 0, and vs ¼ ð2 mAÞð5000 Þ ¼ 10 V. For t > 0, the time constant is ¼ RC ¼ 10 ms and iR ð0þ Þ ¼ 0; iR ð1Þ ¼ 2 mA, and iR ¼ 2ð1 e100t Þ ðmAÞ

[See Fig. 7-24ðbÞ:

þ

vC ð0 Þ ¼ 0; vC ð1Þ ¼ ð2 mAÞð5 kÞ ¼ 10 V, and vC ¼ 10ð1 e100t Þ ðVÞ iC ð0þ Þ ¼ 2 mA; iC ð1Þ ¼ 0, and iC ¼ 2e100t

ðmAÞ

vs ð0þ Þ ¼ 0; vs ð1Þ ¼ ð2 mAÞð5 kÞ ¼ 10 V, and vs ¼ 10ð1 e100t Þ

7.10

In Fig. 7-25, the switch is opened at t ¼ 0.

[See Fig. 7-24ðcÞ:

[See Fig. 7-24ðdÞ: ðVÞ

[See Fig. 7-24ðeÞ:

Find iR , iC , vC , and vs .

For t < 0, the circuit is at steady state with iR ¼ 6ð4Þ=ð4 þ 2Þ ¼ 4 mA, iC ¼ 0, and vC ¼ vs ¼ 4ð2Þ ¼ 8 V. During the switching at t ¼ 0, the capacitor voltage remains the same. After the switch is opened, at t ¼ 0þ , the capacitor has the same voltage vC ð0þ Þ ¼ vC ð0 Þ ¼ 8 V. For t > 0, the capacitor discharges in the 5-k resistor, produced from the series combination of the 3-k and 2-k resistors. The time constant of the circuit is ¼ ð2 þ 3Þð103 Þð2 106 Þ ¼ 0:01 s. The currents and voltages are vC ¼ 8e100t

ðVÞ

iR ¼ iC ¼ vC =5000 ¼ ð8=5000Þe100t ¼ 1:6e100t

ðmAÞ

vs ¼ ð6 mAÞð4 kÞ ¼ 24 V since, for t > 0, all of the 6 mA goes through the 4-k resistor.

7.11

The switch in the circuit of Fig. 7-26 is closed on position 1 at t ¼ 0 and then moved to 2 after one time constant, at t ¼ ¼ 250 ms. Obtain the current for t > 0. It is simplest ﬁrst to ﬁnd the charge on the capacitor, since it is known to be continuous (at t ¼ 0 and at t ¼ ), and then to diﬀerentiate it to obtain the current. For 0 t , q must have the form q ¼ Aet= þ B

CHAP. 7]

FIRST-ORDER CIRCUITS

Fig. 7-24

Fig. 7-25

Fig. 7-26

149

150

FIRST-ORDER CIRCUITS

[CHAP. 7

From the assumption qð0Þ ¼ 0 and the condition dq 20 V ¼ 40 mA ið0þ Þ ¼ 0þ ¼ dt 500 we ﬁnd that A ¼ B ¼ 10 mC, or q ¼ 10ð1 e4000t Þ

ð0 t Þ

ðmCÞ

ð20Þ

1

From (20), qðÞ ¼ 10ð1 e Þ mC; and we know that qð1Þ ¼ ð0:5 mFÞð40 VÞ ¼ 20 mC. Hence, q, is determined for t as q ¼ ½qðÞ qð1ÞeðtÞ= þ qð1Þ ¼ 71:55e4000t 20

ðmCÞ

ð21Þ

Diﬀerentiating (20) and (21), dq ¼ i¼ dt

40e4000t 286:2e4000t

ðmAÞ ðmAÞ

ð0 < t < Þ ðt > Þ

See Fig. 7-27.

Fig. 7-27

7.12

A series RL circuit has a constant voltage V applied at t ¼ 0.

At what time does vR ¼ vL ?

The current in an RL circuit is a continuous function, starting at zero in this case, and reaching the ﬁnal value V=R. Thus, for t > 0, i¼

V ð1 et= Þ R

and

where ¼ L=R is the time constant of the circuit.

vR ¼ Ri ¼ Vð1 et= Þ

Since vR þ vL ¼ V, the two voltages will be equal when vR ¼ 12 V

Vð1 et= Þ ¼ 12 V et= ¼ 12 t ¼ ln 2 that is, when t ¼ 0:693.

7.13

Note that this time is independent of V.

A constant voltage is applied to a series RL circuit at t ¼ 0. 20 V at 3.46 ms and 5 V at 25 ms. Obtain R if L ¼ 2 H. Using the two-point method of Section 7-6.

The voltage across the inductance is

CHAP. 7]

¼ and so

7.14

151

FIRST-ORDER CIRCUITS

t2 t1 25 3:46 ¼ ¼ 15:54 ms ln v1 ln v2 ln 20 ln 5 R¼

L 2 ¼ 128:7 ¼ 15:54 103

In Fig. 7-28, switch S1 is closed at t ¼ 0.

Switch S2 is opened at t ¼ 4 ms.

Obtain i for t > 0.

Fig. 7-28 As there is always inductance in the circuit, the current is a continuous function at all times. In the interval 0 t 4 ms, with the 100 shorted out and a time constant ¼ ð0:1 HÞ=ð50 Þ ¼ 2 ms, i starts at zero and builds toward 100 V ¼ 2A 50 even though it never gets close to that value.

Hence, as in Problem 7.12

i ¼ 2ð1 et=2 Þ wherein t is measured in ms.

ðAÞ

ð0 t 4Þ

ð22Þ

In particular, ið4Þ ¼ 2ð1 e2 Þ ¼ 1:729 A

In the interval t 4 ms, i starts at 1.729 A and decays toward 100=150 ¼ 0:667 A, with a time constant 0:1=150 ¼ 23 ms. Therefore, with t again in ms, i ¼ ð1:729 0:667Þeðt4Þ=ð2=3Þ þ 0:667 ¼ 428:4e3t=2 þ 0:667

7.15

ðAÞ

ðt 4Þ

ð23Þ

In the circuit of Fig. 7-29, the switch is closed at t ¼ 0, when the 6-mF capacitor has charge Q0 ¼ 300 mC. Obtain the expression for the transient voltage vR . The two parallel capacitors have an equivalent capacitance of 3 mF. Then this capacitance is in series with the 6 mF, so that the overall equivalent capacitance is 2 mF. Thus, ¼ RCeq ¼ 40 ms. At t ¼ 0þ , KVL gives vR ¼ 300=6 ¼ 50 V; and, as t ! 1, vR ! 0 (since i ! 0). Therefore, vR ¼ 50 et= ¼ 50et=40

ðVÞ

in which t is measured in ms.

Fig. 7-29

Fig. 7-30

152

7.16

FIRST-ORDER CIRCUITS

[CHAP. 7

In the circuit shown in Fig. 7-30, the switch is moved to position 2 at t ¼ 0. at t ¼ 34:7 ms.

Obtain the current i2

After the switching, the three inductances have the equivalent Leq ¼

10 5ð10Þ þ ¼ 5H 6 15

Then ¼ 5=200 ¼ 25 ms, and so, with t in ms, i ¼ 6et=25

5 i ¼ 2et=25 15

ðAÞ

i2 ð34:7Þ ¼ 2e34:7=25 A ¼ 0:50 A

and

7.17

i2 ¼

ðAÞ

In Fig. 7-31, the switch is closed at t ¼ 0. t > 0.

Obtain the current i and capacitor voltage vC , for

Fig. 7-31 As far as the natural response of the circuit is concerned, the two resistors are in parallel; hence, ¼ Req C ¼ ð5 Þð2 mFÞ ¼ 10 ms By continuity, vC ð0þ Þ ¼ vC ð0 Þ ¼ 0. Furthermore, as t ! 1, the capacitor becomes an open circuit, leaving 20 in series with the 50 V. That is, ið1Þ ¼

50 ¼ 2:5 A 20

vC ð1Þ ¼ ð2:5 AÞð10 Þ ¼ 25 V

Knowing the end conditions on vC , we can write vC ¼ ½vC ð0þ Þ vC ð1Þet= þ vC ð1Þ ¼ 25ð1 et=10 Þ

ðVÞ

wherein t is measured in ms. The current in the capacitor is given by iC ¼ C

dvC ¼ 5et=10 dt

ðAÞ

and the current in the parallel 10- resistor is i10 ¼ Hence,

vC ¼ 2:5ð1 et=10 Þ 10

ðAÞ

i ¼ iC þ i10 ¼ 2:5ð1 þ et=10 Þ ðAÞ

The problem might also have been solved by assigning mesh currents and solving simultaneous diﬀerential equations.

7.18

The switch in the two-mesh circuit shown in Fig. 7-32 is closed at t ¼ 0. and i2 , for t > 0.

Obtain the currents i1

CHAP. 7]

153

FIRST-ORDER CIRCUITS

Fig. 7-32 di1 ¼ 100 dt 10ði1 þ i2 Þ þ 5i2 ¼ 100

10ði1 þ i2 Þ þ 5i1 þ 0:01

From (25), i2 ¼ ð100 10i1 Þ=15.

ð24Þ ð25Þ

Substituting in (24), di1 þ 833i1 ¼ 3333 dt

ð26Þ

The steady-state solution (particular solution) of (26) is i1 ð1Þ ¼ 3333=833 ¼ 4:0 A; hence i1 ¼ Ae833t þ 4:0 ðAÞ The initial condition i1 ð0 Þ ¼ i1 ð0þ Þ ¼ 0 now gives A ¼ 4:0 A, so that i1 ¼ 4:0ð1 e833t Þ

ðAÞ

and

i2 ¼ 4:0 þ 2:67e833t

ðAÞ

Alternate Method When the rest of the circuit is viewed from the terminals of the inductance, there is equivalent resistance Req ¼ 5 þ

5ð10Þ ¼ 8:33 15

Then 1= ¼ Req =L ¼ 833 s1 . At t ¼ 1, the circuit resistance is RT ¼ 10 þ

5ð5Þ ¼ 12:5 10

so that the total current is iT ¼ 100=12:5 ¼ 8 A. And, at t ¼ 1, this divides equally between the two 5- resistors, yielding a ﬁnal inductor current of 4 A. Consequently, iL ¼ i1 ¼ 4ð1 e833t Þ ðAÞ

7.19

A series RL circuit, with R ¼ 50 and L ¼ 0:2 H, has a sinusoidal voltage v ¼ 150 sin ð500t þ 0:785Þ ðVÞ applied at t ¼ 0.

Obtain the current for t > 0.

The circuit equation for t > 0 is di þ 250i ¼ 750 sin ð500t þ 0:785Þ dt

ð27Þ

The solution is in two parts, the complementary function (ic ) and the particular solution ðip Þ, so that i ¼ ic þ ip . The complementary function is the general solution of (27) when the right-hand side is replaced by zero: ic ¼ ke250t . The method of undetermined coeﬃcients for obtaining ip consists in assuming that ip ¼ A cos 500t þ B sin 500t since the right-hand side of (27) can also be expressed as a linear combination of these two functions. Then

154

FIRST-ORDER CIRCUITS

[CHAP. 7

dip ¼ 500A sin 500t þ 500B cos 500t dt Substituting these expressions for ip and dip =dt into (27) and expanding the right-hand side, 500A sin 500t þ 500B cos 500t þ 250A cos 500t þ 250B sin 500t ¼ 530:3 cos 500t þ 530:3 sin 500t Now equating the coeﬃcients of like terms, 500A þ 250B ¼ 530:3

and

500B þ 250A ¼ 530:3

Solving these simultaneous equations, A ¼ 0:4243 A, B ¼ 1:273 A. ip ¼ 0:4243 cos 500t þ 1:273 sin 500t ¼ 1:342 sin ð500t 0:322Þ ðAÞ i ¼ ic þ ip ¼ ke250t þ 1:342 sin ð500t 0:322Þ

and At t ¼ 0, i ¼ 0.

Applying this condition, k ¼ 0:425 A, and, ﬁnally, i ¼ 0:425e250t þ 1:342 sin ð500t 0:322Þ

7.20

ðAÞ

ðAÞ

For the circuit of Fig. 7-33, obtain the current iL , for all values of t.

Fig. 7-33 For t < 0, the 50-V source results in inductor current 50=20 ¼ 2:5 A. The 5-A current source is applied for t > 0. As t ! 1, this current divides equally between the two 10- resistors, whence iL ð1Þ ¼ 2:5 A. The time constant of the circuit is ¼

0:2 103 H 1 ¼ ms 20 100

and so, with t in ms and using iL ð0þ Þ ¼ iL ð0 Þ ¼ 2:5 A, iL ¼ ½iL ð0þ Þ iL ð1Þet= þ iL ð1Þ ¼ 5:0e100t 2:5

ðAÞ

Finally, using unit step functions to combine the expressions for t < 0 and t > 0, iL ¼ 2:5uðtÞ þ ð5:0e100t 2:5ÞuðtÞ

7.21

ðAÞ

The switch in Fig. 7-34 has been in position 1 for a long time; it is moved to 2 at t ¼ 0. the expression for i, for t > 0.

Obtain

With the switch on 1, ið0 Þ ¼ 50=40 ¼ 1:25 A. With an inductance in the circuit, ið0 Þ ¼ ið0þ Þ. after the switch has been moved to 2, ið1Þ ¼ 10=40 ¼ 0:25 A. In the above notation, B ¼ ið1Þ ¼ 0:25 A and the time constant is ¼ L=R ¼ ð1=2000Þ s.

A ¼ ið0þ Þ B ¼ 1:00 A Then, for t > 0,

i ¼ 1:00e2000t þ 0:25

ðAÞ

Long

CHAP. 7]

155

FIRST-ORDER CIRCUITS

Fig. 7-34

7.22

Fig. 7-35

The switch in the circuit shown in Fig. 7-35 is moved from 1 to 2 at t ¼ 0. t > 0.

Find vC and vR , for

With the switch on 1, the 100-V source results in vC ð0 Þ ¼ 100 V; and, by continuity of charge, vC ð0 Þ ¼ vC ð0 Þ. In position 2, with the 50-V source of opposite polarity, vC ð1Þ ¼ 50 V. Thus, þ

B ¼ vC ð1Þ ¼ 50 V

A ¼ vC ð0þ Þ B ¼ 150 V

¼ RC ¼

1 s 200

vC ¼ 150e200t 50 ðVÞ

and Finally, KVL gives vR þ vC þ 50 ¼ 0, or

vR ¼ 150e200t

7.23

ðVÞ

Obtain the energy functions for the circuit of Problem 7.22. wC ¼ 12 Cv2C ¼ 1:25ð3e200t 1Þ2 ðmJÞ ðt 2 vR dt ¼ 11:25ð1 e400t Þ ðmJÞ wR ¼ 0 R

7.24

A series RC circuit, with R ¼ 5 k and C ¼ 20 mF, has two voltage sources in series, v1 ¼ 25uðtÞ ðVÞ

v2 ¼ 25uðt t 0 Þ ðVÞ

Obtain the complete expression for the voltage across the capacitor and make a sketch, if t 0 is positive. The capacitor voltage is continuous. For t 0, v1 results in a capacitor voltage of 25 V. For 0 t t 0 , both sources are zero, so that vC decays exponentially from 25 V towards zero: vC ¼ 25et=RC ¼ 25e10t

ð0 t t 0 Þ

ðVÞ

0

In particular, vC ðt 0 Þ ¼ 25e10t (V). For t t 0 , vC builds from vC ðt 0 Þ towards the ﬁnal value 25 V established by v2 : 0

vC ¼ ½vC ðt 0 Þ vC ð1Þeðtt Þ=RC þ vC ð1Þ 0

¼ 25½1 ðe10t 1Þe10t

ðt t 0 Þ

ðVÞ

Thus, for all t, 0

vC ¼ 25uðtÞ þ 25e10t ½uðtÞ uðt t 0 Þ þ 25½1 ðe10t 1Þe10t uðt t 0 Þ ðVÞ See Fig. 7-36.

156

FIRST-ORDER CIRCUITS

[CHAP. 7

Fig. 7-36

Supplementary Problems 7.25

The capacitor in the circuit shown in Fig. 7-37 has initial charge Q0 ¼ 800 mC, with polarity as indicated. the switch is closed at t ¼ 0, obtain the current and charge, for t > 0. Ans: i ¼ 10e25 000t ðAÞ; q ¼ 4 104 ð1 þ e25 000t Þ ðCÞ

If

Fig. 7-38 Fig. 7-37

7.26

A 2-mF capacitor, with initial charge Q0 ¼ 100 mC, is connected across a 100- resistor at t ¼ 0. Calculate the time in which the transient voltage across the resistor drops from 40 to 10 volts. Ans: 0:277 ms

7.27

In the RC circuit shown in Fig. 7-38, the switch is closed on position 1 at t ¼ 0 and then moved to 2 after the passage of one time constant. Obtain the current transient for (a) 0 < t < ; ðbÞ t > . Ans: ðaÞ 0:5e200t ðAÞ; ðbÞ 0:516e200ðtÞ (A)

7.28

A 10-mF capacitor, with initial charge Q0 , is connected across a resistor at t ¼ 0. Given that the power transient for the capacitor is 800e4000t (W), ﬁnd R, Q0 , and the initial stored energy in the capacitor. Ans: 50 ; 2000 mC; 0:20 J

7.29

A series RL circuit, with R ¼ 10 and L ¼ 1 H, has a 100-V source applied at t ¼ 0. t > 0. Ans: 10ð1 e10t Þ (A)

7.30

In Fig. 7-39, the switch is closed on position 1 at t ¼ 0, then moved to 2 at t ¼ 1 ms. Find the time at which the voltage across the resistor is zero, reversing polarity. Ans: 1:261 ms

7.31

A series RL circuit, with R ¼ 100 and L ¼ 0:2 H, has a 100-V source applied at t ¼ 0; then a second source, of 50 V with the same polarity, is switched in at t ¼ t 0 , replacing the ﬁrst source. Find t 0 such that the current is constant at 0.5 A for t > t 0 . Ans: 1:39 ms

Find the current for

CHAP. 7]

157

FIRST-ORDER CIRCUITS

Fig. 7-39 7.32

The circuit of Problem 7.31 has a 50-V source of opposite polarity switched in at t ¼ 0:50 ms, replacing the ﬁrst source. Obtain the current for (a) 0 < t < 0:50 ms; ðbÞ t > 0:50 ms. Ans: ðaÞ 1 e500t ðAÞ; ðbÞ 0:721e500ðt0:0005Þ 0:50 ðAÞ

7.33

A voltage transient, 35e500t (V), has the value 25 V at t1 ¼ 6:73 104 s. Show that at t ¼ t1 þ the function has a value 36.8 percent of that at t1 :

7.34

A transient that increases from zero toward a positive steady-state magnitude is 49.5 at t1 ¼ 5:0 ms, and 120 at t2 ¼ 20:0 ms. Obtain the time constant . Ans: 12:4 ms

7.35

The circuit shown in Fig. 7-40 is switched to position 1 at t ¼ 0, then to position 2 at t ¼ 3. transient current i for (a) 0 < t < 3; ðbÞ t > 3. Ans: ðaÞ 2:5e50 000t ðAÞ; ðbÞ 1:58e66 700ðt0:00006Þ (A)

Fig. 7-40

Find the

Fig. 7-41

7.36

An RL circuit, with R ¼ 300 and L ¼ 1 H, has voltage v ¼ 100 cos ð100t þ 458Þ (V) applied by closing a switch at t ¼ 0. [A convenient notation has been used for the phase of v, which, strictly, should be indicated as 100t þ ð=4Þ (rad).] Obtain the resulting current for t > 0. Ans: 0:282e300t þ 0:316 cos ð100t þ 26:68Þ (A)

7.37

The RC circuit shown in Fig. 7-41 has an initial charge on the capacitor Q0 ¼ 25 mC, with polarity as indicated. The switch is closed at t ¼ 0, applying a voltage v ¼ 100 sin ð1000t þ 308Þ (V). Obtain the current for t > 0. Ans: 153:5e4000t þ 48:4 sin ð1000t þ 1068Þ (mA)

7.38

What initial charge on the capacitor in Problem 7.37 would cause the current to go directly into the steady state without a transient? Ans: 13:37 mC (þ on top plate)

7.39

Write simultaneous diﬀerential equations for the circuit shown in Fig. 7-42 and solve for i1 and i2 . The switch is closed at t ¼ 0 after having been open for an extended period of time. (This problem can also be solved by applying known initial and ﬁnal conditions to general solutions, as in Problem 7-17.) Ans: i1 ¼ 1:67e6:67t þ 5 ðAÞ; i2 ¼ 0:555e6:67t þ 5 ðAÞ

158

FIRST-ORDER CIRCUITS

Fig. 7-42

[CHAP. 7

Fig. 7-43

(b) 0þ ,

7.40

For the RL circuit shown in Fig. 7-43, ﬁnd the current iL at the following times: (a) 1 ms, (c) 0.3 ms, (d) 1. Ans: ðaÞ 2:00 A; ðbÞ 2:00 A; ðcÞ 2:78 A; ðdÞ 3:00 A

7.41

A series RC circuit, with R ¼ 2 k and C ¼ 40 mF, has two voltage sources in series with each other, v1 ¼ 50 V and v2 ¼ 100uðtÞ (V). Find (a) the capacitor voltage at t ¼ , (b) the time at which the capacitor voltage is zero and reversing polarity. Ans: ðaÞ 13:2 V; ðbÞ 55:5 ms

7.42

Find the unit-impulse response of the circuit of Fig. 7-44; i.e., v2 for v1 ¼ ðtÞ (a unit-area narrow voltage pulse). R 1 t=ðR1 CÞ Ans: v2 ¼ 2 ðtÞ uðtÞ e R1 R1 C

Fig. 7-44 7.43

In the circuits of Fig. 7-45, RC ¼ 5 107 and v1 ðtÞ ¼ 10 þ cos ð1000tÞ þ 3 cos ð2000tÞ. Find v2 ðtÞ. Assume tan when < 18. Ans: v2 ðtÞ 10 þ cos ½1000ðt 106 Þ þ 3 cos ½2000ðt 106 Þ ¼ v1 ðt 106 Þ

Fig. 7-45

CHAP. 7]

159

FIRST-ORDER CIRCUITS

7.44

The input voltage in the circuits of 7-45 is a weighted sum of sinusoids with the highest frequency f0 Hz. Assuming that RC < 1=ð360 f0 Þ, ﬁnd v2 ðtÞ. Ans: v2 ðtÞ v1 ðt 2RCÞ

7.45

Find the relationship between v2 and v1 in the circuit of Fig. 7-46. Ans:

v2 þ RC

dv2 ¼ 2v1 dt

Fig. 7-47 Fig. 7-46 7.46

In the circuit of Fig. 7-47, ﬁnd the diﬀerential equation relating v2 to v1 . Fig. 7-45(a) of Example 7.17. dv 1 dv v1 RC 1 Ans: v2 þ RC 2 ¼ 2 dt dt

7.47

In the circuit of Fig. 7-48, ﬁnd the relationship between v2 and v1 . dv2 C1 dv1 v R2 C2 ¼ Ans: v2 þ R1 C1 dt C2 1 dt

Fig. 7-48

Fig. 7-49

Compare with the circuit of

160

FIRST-ORDER CIRCUITS

[CHAP. 7

7.48

In the circuit of Fig. 7-49, let k ¼ 0. Ans: v ¼ et ; i ¼ 1 0:5et

Find v and i after the switch is closed at t ¼ 0.

7.49

Show that the segment of the circuit enclosed by the dashed box in the circuit of Fig. 7-49 is equivalent to an inductor with value L ¼ 1=ð1 kÞ H. Hint: Write KVL between terminals AB of the dashed box.

7.50

The switch in the circuit of Fig. 7-49 is closed at t ¼ 0. Find v at t > 0 for the following values of k: (a) 0.5, (b) 1, (c) 2. Ans: ðaÞ v ¼ et=2 ; ðbÞ v ¼ 1; ðcÞ v ¼ et

7.51

Find i, the current drawn from the battery, in Problem 7.50. Ans: ðaÞ i ¼ 1 0:5et=2 ; ðbÞ i ¼ 0:5; ðcÞ i ¼ 1 0:5et

Higher-Order Circuits and Complex Frequency 8.1

INTRODUCTION

In Chapter 7, RL and RC circuits with initial currents or charge on the capacitor were examined and ﬁrst-order diﬀerential equations were solved to obtain the transient voltages and currents. When two or more storage elements are present, the network equations will result in second-order diﬀerential equations. In this chapter, several examples of second-order circuits will be presented. This will then be followed by more direct methods of analysis, including complex frequency and pole-zero plots.

8.2

SERIES RLC CIRCUIT

The second-order diﬀerential equation, which will be examined shortly, has a solution that can take three diﬀerent forms, each form depending on the circuit elements. In order to visualize the three possibilities, a second-order mechanical system is shown in Fig. 8-1. The mass M is suspended by a spring with a constant k. A damping device D is attached to the mass M. If the mass is displaced from its rest position and then released at t ¼ 0, its resulting motion will be overdamped, critically damped, or underdamped (oscillatory). Figure 8-2 shows the graph of the resulting motions of the mass after its release from the displaced position z1 (at t ¼ 0).

Fig. 8-1

161 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

162

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Fig. 8-2

The series RLC circuit shown in Fig. 8-3 contains no voltage source. the closed loop after the switch is closed is

Kirchhoﬀ’s voltage law for

vR þ vL þ vC ¼ 0 ð di 1 i dt ¼ 0 Ri þ L þ dt C

or

Diﬀerentiating and dividing by L yields d 2 i R di 1 þ i¼0 þ 2 L dt LC dt A solution of this second-order diﬀerential equation is of the form i ¼ A1 es1 t þ A2 es2 t . solution in the diﬀerential equation obtains

Substituting this

Fig. 8-3

R 1 R 1 A1 es1 t s21 þ s1 þ þ A2 es2 t s22 þ s2 þ ¼0 L LC L LC that is, if s1 and s2 are the roots of s2 þ ðR=LÞs þ ð1=LCÞ ¼ 0, R s1 ¼ þ 2L where R=2L,

sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 R 1 þ 2L LC

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃ 2 !20 , and !0 1= LC .

R s2 ¼ 2L

sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 R 1 2L LC

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

163

Overdamped Case ð > !0 Þ In this case, both and are real positive numbers. i ¼ A1 eðþÞt þ A2 eðÞt ¼ et ðA1 et þ A2 et Þ EXAMPLE 8.1 A series RLC circuit, with R ¼ 200 , L ¼ 0:10 H, and C ¼ 13:33 mF, has an initial charge on the capacitor of Q0 ¼ 2:67 103 C. A switch is closed at t ¼ 0, allowing the capacitor to discharge. Obtain the current transient. (See Fig. 8-4.) For this circuit, qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ R 1 ¼ 103 s1 ; ¼ 7:5 105 s2 ; ¼ !20 ¼ and ¼ 2 !20 ¼ 500 s1 2L LC i ¼ e1000t ðA1 e500t þ A2 e500t Þ

Then,

The values of the constants A1 and A2 are obtained from the initial conditions. The inductance requires that ið0þ Þ ¼ ið0 Þ. Also the charge and voltage on the capacitor at t ¼ 0þ must be the same as at t ¼ 0 , and vC ð0 Þ ¼ Q0 =C ¼ 200 V. Applying these two conditions, 0 ¼ A1 þ A2

and

2000 ¼ 500A1 1500A2

from which A1 ¼ 2; A2 ¼ 2, and, taking A1 positive, i ¼ 2e500t 2e1500t

ðAÞ

If the negative value is taken for A1 , the function has simply ﬂipped downward but it has the same shape. The signs of A1 and A2 are ﬁxed by the polarity of the initial voltage on the capacitor and its relationship to the assumed positive direction for the current.

Fig. 8-4

Critically Damped Case ð ¼ !0 Þ With ¼ !0 , the diﬀerential equation takes on a diﬀerent form and the two exponential terms suggested in the preceding will no longer provide a solution. The equation becomes d 2i di þ 2 þ 2 i ¼ 0 dt dt2 and the solution takes the form i ¼ et ðA1 þ A2 tÞ. EXAMPLE 8.2 Repeat Example 8.1 for C ¼ 10 mF, which results in ¼ !0 . As in Example 8.1, the initial conditions are used to determine the constants. 0 ¼ ½A1 þ A2 ð0Þ and A1 ¼ 0. Then,

Since ið0 Þ ¼ ið0þ Þ,

di d ¼ ðA tet Þ ¼ A2 ðteat þ et Þ dt dt 2 3

from which A2 ¼ ðdi=dtÞj0þ ¼ 2000. Hence, i ¼ 2000te10 t (A) (see Fig. 8-5). Once again the polarity is a matter of the choice of direction for the current with respect to the polarity of the initial voltage on the capacitor.

164

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Fig. 8-5

The responses for the overdamped and critically damped cases plotted in Figs. 8-4 and 8-5, respectively, are quite similar. The reader is encouraged to examine the results, selecting several values for t, and comparing the currents. For example, ﬁnd the time at which the current in each of the two cases reaches the values of 1.0 mA and 1.0 mA. Also, in each case, ﬁnd t1 for the maximum current. Underdamped or Oscillatory Case ð < !0 Þ When < !0 , s1 and s2 in the solution to the diﬀerential equation suggested qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃin the preceding are complex conjugates s1 ¼ þ j and s2 ¼ j, where is now given by !20 2 . The solution can be written in the exponential form i ¼ et ðA1 e jt þ A2 ejt Þ or, in a readily derived sinusoidal form, i ¼ et ðA3 cos t þ A4 sin tÞ EXAMPLE 8.3 Repeat Example 8.1 for C ¼ 1 mF. As before, ¼

R ¼ 1000 s1 2L

!20 ¼

1 ¼ 107 s2 LC

¼

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 107 106 ¼ 3000 rad=s

i ¼ e1000t ðA3 cos 3000t þ A4 sin 3000tÞ

Then,

The constants A3 and A4 are obtained from the initial conditions as before, ið0þ Þ ¼ 0 and vc ð0þ Þ ¼ 200 V. From this A3 ¼ 0 and A4 ¼ 0:667. Thus, i ¼ 0:667e1000t ðsin 3000tÞ ðAÞ See Fig. 8-6. The function 0:667e1000t , shown dashed in the graph, provides an envelope within which the sine function is conﬁned. The oscillatory current has a radian frequency of (rad/s), but is damped by the exponential term et .

8.3

PARALLEL RLC CIRCUIT

The response of the parallel RLC circuit shown in Fig. 8-7 will be similar to that of the series RLC circuit, since a second-order diﬀerential equation can be expected. The node voltage method gives ð v 1 t dv þ ¼0 ð1Þ v dt þ C R L 0 dt Diﬀerentiating and dividing by C yields d 2v 1 dv v þ ¼0 þ dt2 RC dt LC A solution is of the form

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

165

Fig. 8-6

v ¼ A 1 es 1 t þ A 2 es 2 t ð2Þ sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 1 2 1 þ ¼ þ 2 !20 where s1 ¼ 2RC 2RC LC sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 1 1 ¼ 2 !20 s2 ¼ 2RC 2RC LC pﬃﬃﬃﬃﬃﬃﬃ where ¼ 1=2RC and !0 ¼ 1= LC . Note that , the damping factor of the transient, diﬀers from in the series RLC circuit.

Fig. 8-7

The transient response is easiest to visualize by assuming an initial charge Q0 on the capacitor and a switch that closes at t ¼ 0. However, a step function voltage applied to the circuit will initiate the same transient response. Overdamped Case ð2 > !20 Þ In this case, the solution (2) applies. EXAMPLE 8.4 A parallel RLC circuit, with R ¼ 1000 , C ¼ 0:167 mF, and L ¼ 1:0 H, has an initial voltage V0 ¼ 50:0 V on the capacitor. Obtain the voltage vðtÞ when the switch is closed at t ¼ 0. We have ¼

1 ¼ 2994 2RC

2 ¼ 8:96 106

!20 ¼

1 ¼ 5:99 106 LC

166

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Since 2 > !20 , the circuit is overdamped and from (2) we have qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ s1 ¼ þ 2 !20 ¼ 1271 and s2 ¼ 2 !20 ¼ 4717 dv At t ¼ 0; and ¼ s A þ s2 A 2 V0 ¼ A1 þ A2 dt t¼0 1 1 From the nodal equation (1), at t ¼ 0 and with no initial current in the inductance L, V0 dv dv V ¼0 or þC ¼ 0 dt dt t¼0 R RC Solving for A1 , A1 ¼

V0 ðs2 þ 1=RCÞ ¼ 155:3 s2 s1

and

A1 ¼ V0 A1 ¼ 50:0 155:3 ¼ 105:3

Substituting into (2) v ¼ 155:3e1271t 105:3e4717t

ðVÞ

See Fig. 8-8.

Fig. 8-8

Underdamped (Oscillatory) Case ð!20 > 2 Þ The oscillatory case for the parallel RLC circuit results in an equation of the same form as that of the underdamped series RLC circuit. Thus, v ¼ et ðA1 cos !d t þ A2 sin !d tÞ

ð3Þ

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ where ¼ 1=2RC and !d ¼ !20 2 . !d is a radian frequency just as was the case with sinusoidal circuit analysis. Here it is the frequency of the damped oscillation. It is referred to as the damped radian frequency. EXAMPLE 8.5 A parallel RLC circuit, with R ¼ 200 , L ¼ 0:28 H, and C ¼ 3:57 mF, has an initial voltage V0 ¼ 50:0 V on the capacitor. Obtain the voltage function when the switch is closed at t ¼ 0. ¼

1 1 ¼ ¼ 700 2RC 2ð200Þð3:57 106 Þ

2 ¼ 4:9 105

Since !20 > 2 , the circuit parameters result in an oscillatory response.

!20 ¼

1 1 ¼ ¼ 106 LC ð0:28Þð3:57 106 Þ

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

!d ¼

167

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !20 2 ¼ 106 ð4:9 105 Þ ¼ 714

At t ¼ 0, V0 ¼ 50:0; hence in (3) A1 ¼ V0 ¼ 50:0. From the nodal equation ð V0 1 t dv ¼0 v dt þ C þ dt R L 0 dv V ¼ 0 dt t ¼ 0 RC

at t ¼ 0, Diﬀerentiating the expression for v and setting t ¼ 0 yields dv ¼ !d A2 A1 or dt t¼0

!d A2 A1 ¼

V0 RC

Since A1 ¼ 50:0, A2 ¼ and so

ðV0 =RCÞ þ V0 ¼ 49:0 !d

v ¼ e700t ð50:0 cos 714t 49:0 sin 714tÞ

ðVÞ

The critically damped case will not be examined for the parallel RLC circuit, since it has little or no real value in circuit design. In fact, it is merely a curiosity, since it is a set of circuit constants whose response, while damped, is on the verge of oscillation.

8.4

TWO-MESH CIRCUIT

The analysis of the response for a two-mesh circuit which contains two storage elements results in simultaneous diﬀerential equation as shown in the following.

Fig. 8-9

For the circuit of Fig. 8-9, choose mesh currents i1 and i2 , as indicated. order diﬀerential equations

KVL yields the two ﬁrst-

di1 þ R 1 i2 ¼ V dt di R1 i1 þ ðR1 þ R2 Þi2 þ L2 2 ¼ V dt R1 i1 þ L1

which must be solved simultaneously. R1

ð4Þ ð5Þ

To accomplish this, take the time derivative of (4), di1 d 2i di þ L1 21 þ R1 2 ¼ 0 dt dt dt

ð6Þ

and then eliminate i2 and di2 =dt between (4), (5), and (6). The following result is a second-order equation for i1 , of the types treated in Sections 8.2 and 8.3, except for the constant term on the right:

168

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

d 2 i1 R1 L1 þ R2 L1 þ R1 L2 di1 R1 R2 R V þ þ i1 ¼ 2 2 L1 L2 L1 L2 dt L1 L2 dt

[CHAP. 8

ð7Þ

The steady-state solution of (7) is evidently i1 ð1Þ ¼ V=R1 ; the transient solution will be determined by the roots s1 and s2 of s2 þ

R1 L1 þ R2 L1 þ R1 L2 R R sþ 1 2 ¼0 L1 L2 L1 L2

together with the initial conditions di1 V ¼ þ 0 L1 dt

i1 ð0þ Þ ¼ 0

(both i1 and i2 must be continuous at t ¼ 0). Once the expression for i1 is known, that for i2 follows from (4). There will be a damping factor that insures the transient will ultimately die out. Also, depending on the values of the four circuit constants, the transient can be overdamped or underdamped, which is oscillatory. In general, the current expression will be i1 ¼ ðtransientÞ þ

V R1

The transient part will have a value of V=R1 at t ¼ 0 and a value of zero as t ! 1.

8.5

COMPLEX FREQUENCY

We have examined circuits where the driving function was a constant (e.g., V ¼ 50:0 V), a sinusoidal function (e.g., v ¼ 100:0 sin ð500t þ 308Þ (V), or an exponential function, e.g., v ¼ 10e5t (V). In this section, we introduce a complex frequency, s, which uniﬁes the three functions and will simplify the analysis, whether the transient or steady-state response is required. We begin by expressing the exponential function in the equivalent cosine and sine form: e jð!tþÞ ¼ cos ð!t þ Þ þ j sin ð!t þ Þ We will focus exclusively on the cosine term cos ð!t þ Þ ¼ Re e jð!tþÞ and for convenience drop the preﬁx Re. Introducing a constant A and the factor et , Aet e jð!tþÞ ) Aet cos ð!t þ Þ

Ae j eðþj!Þt ¼ Ae j est 1

where s ¼ þ j!

The complex frequency s ¼ þ j! has units s , and !, as we know, has units rad/s. Consequently, the units on must also be s1 . This is the neper frequency with units Np/s. If both and ! are

Fig. 8-10

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

169

nonzero, the function is a damped cosine. Only negative values of are considered. If and ! are zero, the result is a constant. And ﬁnally, with ! ¼ 0 and nonzero, the result is an exponential decay function. In Table 8-1, several functions are given with corresponding values of s for the expression Aest . Table 8-1 f ðtÞ 5t

10e 5 cos ð500t þ 308Þ 2e3t cos ð100t 458Þ 100:0

s

A

5 þ j 0 þ j500 3 þ j100 0 þ j0

10 5 2 100.0

When Fig. 8-10 is examined for various values of s, the three cases are evident. If ¼ 0, there is no damping and the result is a cosine function with maximum values of Vm (not shown). If ! ¼ 0, the function is an exponential decay with an initial value Vm . And ﬁnally, with both ! and nonzero, the damped cosine is the result.

8.6

GENERALIZED IMPEDANCE (R; L; C) IN s-DOMAIN

A driving voltage of the form v ¼ Vm est applied to a passive network will result in branch currents and voltages across the elements, each having the same time dependence est ; e.g., Ia e j est , and Vb e j est . Consequently, only the magnitudes of currents and voltages and the phase angles need be determined (this will also be the case in sinusoidal circuit analysis in Chapter 9). We are thus led to consider the network in the s-domain (see Fig. 8-11).

Fig. 8-11

A series RL circuit with an applied voltage v ¼ Vm e j est will result in a current i ¼ Im e j est ¼ Im est , which, substituted in the nodal equation Ri þ L

di ¼ Vm e j est dt

will result in RIm est ¼ sLIm est ¼ Vm e j est

from which

Im ¼

Vm e j R þ sL

Note that in the s-domain the impedance of the series RL circuit is R þ sL. fore has an s-domain impedance sL.

The inductance there-

170

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

EXAMPLE 8.6 A series RL circuit, with R ¼ 10 and L ¼ 2 H, has an applied voltage v ¼ 10 e2t cos ð10t þ 308Þ. Obtain the current i by an s-domain analysis. v ¼ 10

308 est ¼ Ri þ L

di di ¼ 10i þ 2 dt dt

Since i ¼ Iest , 10 308 est ¼ 10Iest þ 2sIest

or

I¼

10 308 10 þ 2s

Substituting s ¼ 2 þ j10, I¼

10 308 10 308 ¼ ¼ 0:48 43:38 10 þ 2ð2 þ j10Þ 6 þ j20

Then, i ¼ Iest ¼ 0:48e2t cos ð10t 43:38Þ (A). EXAMPLE 8.7 A series RC circuit, with R ¼ 10 and C ¼ 0:2 F, has the same applied voltage as in Example 8.6. Obtain the current by an s-domain analysis. As in Example 8.6, ð ð 1 i dt ¼ 10i þ 5 i dt v ¼ 10 308 est ¼ Ri þ C Since i ¼ Iest , 10

308 est ¼ 10Iest þ

5 st Ie s

from which

I¼

10 308 ¼ 1:01 10 þ 5=s

32:88

Then, i ¼ 1:01e2t cos ð10t þ 32:88Þ (A).

Note that the s-domain impedance for the capacitance is 1=ðsCÞ. a series RLC circuit will be ZðsÞ ¼ R þ sL þ 1=ðsCÞ

8.7

Thus the s-domain impedance of

NETWORK FUNCTION AND POLE-ZERO PLOTS

A driving voltage of the form v ¼ Vest applied to a passive network will result in currents and voltages throughout the network, each having the same time function est ; for example, Ie j est . Therefore, only the magnitude I and phase angle need be determined. We are thus led to consider an s-domain where voltages and currents are expressed in polar form, for instance, V , I , and so on. Figure 8-12 suggests the correspondence between the time-domain network, where s ¼ þ j!, and the

Fig. 8-12

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

171

s-domain where only magnitudes and phase angles are shown. In the s-domain, inductances are expressed by sL and capacitances by 1=ðsCÞ. The impedance in the s-domain is ZðsÞ ¼ VðsÞ=IðsÞ. A network function HðsÞ is deﬁned as the ratio of the complex amplitude of an exponential output YðsÞ to the complex amplitude of an exponential input XðsÞ If, for example, XðsÞ is a driving voltage and YðsÞ is the output voltage across a pair of terminals, then the ratio YðsÞ=XðsÞ is nondimensional. The network function HðsÞ can be derived from the input-output diﬀerential equation an

dny d n1 y dy d mx d m1 x dx þ a0 y ¼ bm m þ bm1 m1 þ þ b1 þ b0 x þ an1 n1 þ þ a1 n dt dt dt dt dt dt

When xðtÞ ¼ Xest and yðtÞ ¼ Yest , ðan sn þ an1 sn1 þ þ a1 s þ a0 Þest ¼ ðbm sm þ bm1 sm1 þ þ b1 s þ b0 Þest Then, HðsÞ ¼

YðsÞ a sn þ an1 sn1 þ þ a1 s þ a0 ¼ nm XðsÞ bm s þ bm1 sm1 þ þ b1 s þ b0

In linear circuits made up of lumped elements, the network function HðsÞ is a rational function of s and can be written in the following general form HðsÞ ¼ k

ðs z1 Þðs z2 Þ ðs z Þ ðs p1 Þðs p2 Þ ðs p Þ

where k is some real number. The complex constants zm ðm ¼ 1; 2; . . . ; Þ, the zeros of HðsÞ, and the pn ðn ¼ 1; 2; . . . ; Þ the poles of HðsÞ, assume particular importance when HðsÞ is interpreted as the ratio of the response (in one part of the s-domain network) to the excitation (in another part of the network). Thus, when s ¼ zm , the response will be zero, no matter how great the excitation; whereas, when s ¼ pn , the response will be inﬁnite, no matter how small the excitation. EXAMPLE 8.8 A passive network in the s-domain is shown in Fig. 8-13. current IðsÞ due to an input voltage VðsÞ.

IðsÞ 1 ¼ VðsÞ ZðsÞ 5s 20 s2 þ 8s þ 12 3 s ZðsÞ ¼ 2:5 þ ¼ ð2:5Þ 5s 20 s2 þ 12 þ 3 s HðsÞ ¼

Since

Obtain the network function for the

we have HðsÞ ¼ ð0:4Þ

s2 þ 12 ðs þ 2Þðs þ 6Þ

Fig. 8-13

172

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

pﬃﬃﬃﬃﬃ The numerator of HðsÞ in Example 8.8 is zero when s ¼ j 12. Consequently, a voltage function at this frequency results in a current of zero. In Chapter 12 where series and are pﬃﬃﬃﬃﬃﬃﬃparallel resonance 5 H and discussed, it will be found that the parallel LC circuit is resonant at ! ¼ 1= LC . With L ¼ 3 pﬃﬃﬃﬃﬃ 1 C ¼ 20 F, ! ¼ 12 rad/s. The zeros and poles of a network function HðsÞ can be plotted in a complex s-plane. Figure 8-14 shows the poles and zeros of Example 8.8, with zeros marked 8 and poles marked . The zeros occur pﬃﬃﬃﬃﬃ in complex conjugate pairs, s ¼ j 12, and the poles are s ¼ 2 and s ¼ 6.

Fig. 8-14

8.8

THE FORCED RESPONSE

The network function can be expressed in polar form and the response obtained graphically. Before starting the development, it is helpful to recall that HðsÞ is merely a ratio such as V0 ðsÞ=Vi ðsÞ, I2 ðsÞ=V1 ðsÞ, or I2 ðsÞ=I1 ðsÞ. With the polynomials factored, HðsÞ ¼ k

ðs z1 Þðs z2 Þ ðs z Þ ðs p1 Þðs z2 Þ ðs p Þ

Now setting ðs zm Þ ¼ Nm m ðm ¼ 1; 2; . . . ; Þ and ðs pn Þ ¼ Dn n ðn ¼ 1; 2; . . . ; Þ, we have HðsÞ ¼ k

ðN1 1 ÞðN2 2 Þ ðN Þ ðD1 1 ÞðD2 2 Þ ðD Þ

¼k

N1 N2 N ð1 þ þ Þ ð1 þ þ Þ D1 D2 D

It follows that the response of the network to an excitation for which s ¼ þ j! is determined by measuring the lengths of the vectors from the zeros and poles to s as well as the angles these vectors make with the positive axis in the pole-zero plot. EXAMPLE 8.9 Test the response of the network of Example 8.8 to an exponential voltage excitation v ¼ 1est , where s ¼ 1 Np/s: Locate the test point 1 þ j0 on the pole-zero plot. Draw the vectors from the poles and zeros to the test point and compute the lengths and angles (see Fig. 8-15). Thus, pﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃ N1 ¼ N2 ¼ 13; D1 ¼ 3; D2 ¼ 7; 1 ¼ 2 ¼ 0; and 1 ¼ 2 ¼ tan1 12 ¼ 73:98 Hence,

Hð1Þ ¼ ð0:4Þ

pﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃ ð 13Þð 13Þ 08 08 ¼ 0:248 ð3Þð7Þ

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

173

Fig. 8-15

The result implies that, in the time domain, iðtÞ ¼ 0:248vðtÞ, so that both voltage and current become inﬁnite according to the function e1t . For most practical cases, must be either negative or zero. The above geometrical method does not seem to require knowledge of the analytic expression for HðsÞ as a rational function. It is clear, however, that the expression can be written, to within the constant factor k, from the known poles and zeros of HðsÞ in the pole-zero plot. See Problem 8.37.

8.9

THE NATURAL RESPONSE

This chapter has focused on the forced or steady-state response, and it is in obtaining that response that the complex-frequency method is most helpful. However, the natural frequencies, which characterize the transient response, are easily obtained. They are the poles of the network function. EXAMPLE 8.10 The same network as in Example 8.8 is shown in Fig. 8-16. source VðsÞ is inserted at xx 0 .

Obtain the natural response when a

Fig. 8-16 The network function is the same as in Example 8.8: HðsÞ ¼ ð0:4Þ The natural frequencies are then 2 Np/s and 6 Np/s. is of the form

s2 þ 12 ðs þ 2Þðs þ 6Þ Hence, in the time domain, the natural or transient current

in ¼ A1 e2t þ A2 e6t

174

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

where the constants A1 and A2 are determined by applying the initial conditions to the complete response, i ¼ in þ if , where if indicates the forced response. EXAMPLE 8.11 The network of Fig. 8-16 is driven by current IðsÞ across terminals yy 0 . HðsÞ ¼ VðsÞ=IðsÞ ¼ ZðsÞ. The three branches are in parallel so that HðsÞ ¼ ZðsÞ ¼

The network function is

1 20s ¼ 1 3 s ðs þ 2Þðs þ 6Þ þ þ 2:5 5s 20

Again the poles are at 2 Np/s and 6 Np/s, which is the same result as that obtained in Example 8.10.

8.10

MAGNITUDE AND FREQUENCY SCALING

Magnitude Scaling Let a network have input impedance function Zin ðsÞ, and let Km be a positive real number. Then, if each resistance R in the network is replaced by Km R, each inductance L by Km L, and each capacitance C by C=Km , the new input impedance function will be Km Zin ðsÞ. We say that the network has been magnitude-scaled by a factor Km . Frequency Scaling If, instead of the above changes, we preserve each resistance R, replace each inductance L by L=Kf ðKf > 0Þ, and replace each capacitance C by C=Kf , then the new input impedance function will be Zin ðs=Kf Þ. That is, the new network has the same impedance at complex frequency Kf s as the old had at s. We say that the network has been frequency-scaled by a factor Kf . EXAMPLE 8.12 Express ZðsÞ for the circuit shown in Fig. 8-17 and observe the resulting magnitude scaling. Km Cs ¼ K Ls þ Rð1=CsÞ ZðsÞ ¼ Km Ls þ m K R þ ð1=CsÞ Km R þ m Cs ðKm RÞ

Fig. 8-17

There are practical applications suggested by this brief exposure to magnitude scaling. For example, if the input current to a network were greater than it should be, a factor Km ¼ 10 would reduce the current to 1/10 of the former value.

CHAP. 8]

8.11

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

175

HIGHER-ORDER ACTIVE CIRCUITS

Application of circuit laws to circuits which contain op amps and several storage elements produces, in general, several ﬁrst-order diﬀerential equations which may be solved simultaneously or be reduced to a higher-order input-output equation. A convenient tool for developing the equations is the complex frequency s (and generalized impedance in the s-domain) as used throughout Sections 8.5 to 8.10. Again, we assume ideal op amps (see Section 7.16). The method is illustrated in the following examples. EXAMPLE 8.13 Find HðsÞ ¼ V2 =V1 in the circuit of Fig. 8-41 and show that the circuit becomes a noninverting integrator if and only if R1 C1 ¼ R2 C2 . Apply voltage division, in the phasor domain, to the input and feedback paths to ﬁnd the voltages at the terminals of the op amp. At terminal A: At terminal B: But VA ¼ VB .

1 V 1 þ R1 C1 s 1 R2 C2 s V VB ¼ 1 þ R2 C2 s 2

VA ¼

Therefore, V2 1 þ R2 C2 s ¼ V1 ð1 þ R1 C1 sÞR2 C2 s

Only if R1 C1 ¼ R2 C2 ¼ RC do we get an integrator with a gain of 1=RC ð V2 1 1 t ; v2 ¼ ¼ v dt RC 1 1 V1 RCs EXAMPLE 8.14 The circuit of Fig. 8-42 is called an equal-component Sallen-Key circuit. Find HðsÞ ¼ V2 =V1 and convert it to a diﬀerential equation. Write KCL at nodes A and B. VA V1 VA VB þ þ ðVA V2 ÞCs ¼ 0 R R VB VA þ VB Cs ¼ 0 At node B: R Let 1 þ R2 =R1 ¼ k, then V2 ¼ kVB . Eliminating VA and VB between the above equations we get At node A:

V2 k ¼ V1 R2 C 2 s2 þ ð3 kÞRCs þ 1 R2 C 2

d 2 v2 dv þ ð3 kÞRC 2 þ v2 ¼ kv1 dt dt2

EXAMPLE 8.15 In the circuit of Fig. 8-42 assume R ¼ 2 k, C ¼ 10 nF, and R2 ¼ R1 . By substituting the element values in HðsÞ found in Example 8.14 we obtain

Find v2 if v1 ¼ uðtÞ.

V2 2 ¼ V1 4 1010 s2 þ 2 105 s þ 1 d 2 v2 dv þ 5 104 2 þ 25 108 v2 ¼ 5 109 v1 dt dt2 The response of the preceding equation for t > 0 to v1 ¼ uðtÞ is v2 ¼ 2 þ et ð2 cos !t 2:31 sin !tÞ ¼ 2 þ 3:055et cos ð!t þ 130:98Þ where ¼ 25 000 and ! ¼ 21 651 rad/s. EXAMPLE 8.16 Find conditions in the circuit of Fig. 8-42 for sustained oscillations in v2 ðtÞ (with zero input) and ﬁnd the frequency of oscillations. In Example 8.14 we obtained V2 k ¼ V1 R2 C 2 s2 þ ð3 kÞRCs þ 1

176

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

For sustained oscillations the roots of the characteristic equation in Example 8.14 should be imaginary numbers. This happens when k ¼ 3 or R2 ¼ 2R1 , in which case ! ¼ 1=RC.

Solved Problems 8.1

A series RLC circuit, with R ¼ 3 k, L ¼ 10 H, and C ¼ 200 mF, has a constant-voltage source, V ¼ 50 V, applied at t ¼ 0. (a) Obtain the current transient, if the capacitor has no initial charge. (b) Sketch the current and ﬁnd the time at which it is a maximum. ¼

ðaÞ

R ¼ 150 s1 2L

!20 ¼

1 ¼ 500 s2 LC

¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 !20 ¼ 148:3 s1

The circuit is overdamped ð > !0 Þ. s1 ¼ þ ¼ 1:70 s1

s2 ¼ ¼ 298:3 s1

i ¼ A1 e1:70t þ A2 e298:3t

and

Since the circuit contains an inductance, ið0þ Þ ¼ ið0 Þ ¼ 0; also, Qð0þ Þ ¼ Qð0 Þ ¼ 0. KVL gives di di V or ¼ ¼ 5 A=s 0 þ 0 þ L 0þ ¼ V dt dt 0þ L Applying these initial conditions to the expression for i, 0 ¼ A1 ð1Þ þ A2 ð1Þ 5 ¼ 1:70A1 ð1Þ 298:3A2 ð1Þ from which A1 ¼ A2 ¼ 16:9 mA. i ¼ 16:9ðe1:70t e298:3t Þ

ðmAÞ

(b) For the time of maximum current, di ¼ 0 ¼ 28:73e1:70t þ 5041:3e298:3t dt Solving by logarithms, t ¼ 17:4 ms.

See Fig. 8-18.

Fig. 8-18

Thus, at t ¼ 0þ ,

CHAP. 8]

8.2

177

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

A series RLC circuit, with R ¼ 50 ; L ¼ 0:1 H; and C ¼ 50 mF, has a constant voltage V ¼ 100 V applied at t ¼ 0. Obtain the current transient, assuming zero initial charge on the capacitor. ¼

R ¼ 250 s1 2L

!20 ¼

1 ¼ 2:0 105 s2 LC

¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 !20 ¼ j370:8 rad=s

This is an oscillatory case ð < !0 Þ, and the general current expression is i ¼ e250t ðA1 cos 370:8 t þ A2 sin 370:8tÞ The initial conditions, obtained as in Problem 8.1, are þ

ið0 Þ ¼ 0

di ¼ 1000 A=s dt 0þ

and these determine the values: A1 ¼ 0, A2 ¼ 2:70 A.

Then

i ¼ e250t ð2:70 sin 370:8tÞ

8.3

ðAÞ

Rework Problem 8.2, if the capacitor has an initial charge Q0 ¼ 2500 mC. Everything remains the same as in Problem 8.2 except the second initial condition, which is now di Q0 di 100 ð2500=50Þ ¼ 500 A=s ¼V or 0þL þ ¼ dt þ C dt þ 0:1 0

0

The initial values are half those in Problem 8.2, and so, by linearity, i ¼ e250t ð1:35 sin 370:8tÞ

8.4

ðAÞ

A parallel RLC network, with R ¼ 50:0 , C ¼ 200 mF, and L ¼ 55:6 mH, has an initial charge Q0 ¼ 5:0 mC on the capacitor. Obtain the expression for the voltage across the network. 1 ¼ 8:99 104 s2 LC qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Since !20 > 2 , the voltage function is oscillatory and so !d ¼ !20 2 ¼ 296 rad/s. expression is ¼

1 ¼ 50 s1 2RC

!20 ¼

The general voltage

v ¼ e50t ðA1 cos 296t þ A2 sin 296tÞ With Q0 ¼ 5:0 103 C, V0 ¼ 25:0 V.

At t ¼ 0, v ¼ 25:0 V.

Then, A1 ¼ 25:0.

dv ¼ 50e50t ðA1 cos 296t þ A2 sin 296tÞ þ 296e50t ðA1 sin 296t þ A2 cos 296tÞ dt At t ¼ 0, dv=dt ¼ V0 =RC ¼ !d A2 A1 , from which A2 ¼ 4:22. 50t

v¼e

8.5

Thus,

ð25:0 cos 296t 4:22 sin 296tÞ ðVÞ

In Fig. 8-19, the switch is closed at t ¼ 0. t > 0.

Obtain the current i and capacitor voltage vC , for

As far as the natural response of the circuit is concerned, the two resistors are in parallel; hence, ¼ Req C ¼ ð5 Þð2 mFÞ ¼ 10 ms By continuity, vC ð0þ Þ ¼ vC ð0 Þ ¼ 0. Furthermore, as t ! 1, the capacitor becomes an open circuit, leaving 20 in series with the 50 V. That is, ið1Þ ¼

50 ¼ 2:5 A 20

vC ð1Þ ¼ ð2:5 AÞð10 Þ ¼ 25 V

178

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Fig. 8-19 Knowing the end conditions on vC , we can write vC ¼ ½vC ð0þ Þ vC ð1Þet= þ vC ð1Þ ¼ 25ð1 et=10 Þ

ðVÞ

wherein t is measured in ms. The current in the capacitor is given by iC ¼ C

dvC ¼ 5et=10 dt

ðAÞ

and the current in the parallel 10- resistor is vC ¼ 2:5ð1 et=10 Þ 10

ðAÞ

i ¼ iC þ i10 ¼ 2:5ð1 þ et=10 Þ

ðAÞ

i10 ¼ Hence,

The problem might also have been solved by assigning mesh currents and solving simultaneous diﬀerential equations.

8.6

For the time functions listed in the ﬁrst column of Table 8-2, write the corresponding amplitude and phase angle (cosine-based) and the complex frequency s. See columns 2 and 3 of the table. Table 8-2 Time Function iðtÞ ¼ 86:6 A 3 iðtÞ ¼ 15:0e210 t ðAÞ vðtÞ ¼ 25:0 cos ð250t 458Þ ðVÞ vðtÞ ¼ 0:50 sin ð250t þ 308Þ ðVÞ iðtÞ ¼ 5:0e100t sin ð50t þ 908Þ ðAÞ iðtÞ ¼ 3 cos 50t þ 4 sin 50t ðAÞ

8.7

A 8

s

86:6 08 A 15:0 08 A 25:0 458 V 0:50 608 V 5:0 08 A 5 53:138 A

0 2 103 Np/s j250 rad/s j250 rad/s 100 j50 s1 j50 rad/s

For each amplitude and phase angle in the ﬁrst column and complex frequency s in the second column in Table 8-3, write the corresponding time function. See column 3 of the table. Table 8-3 A 8 10 08 2 458 5 908 15 08 100 308

s

Time Function

þj120 j120 2 j50 5000 j1000 0

10 cos 120 t 2 cos ð120 t þ 458Þ 5e2t cos ð50t 908Þ 15e5000t cos 1000t 86.6

CHAP. 8]

8.8

pﬃﬃﬃ An amplitude and phase angle of 10 2 458 V has an associated complex frequency s ¼ 50 þ j 100 s1 . Find the voltage at t ¼ 10 ms. pﬃﬃﬃ vðtÞ ¼ 10 2e50t cos ð100t þ 458Þ 2

At t ¼ 10

8.9

179

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

ðVÞ

s, 100t ¼ 1 rad ¼ 57:38, and so pﬃﬃﬃ v ¼ 10 2e0:5 cos 102:38 ¼ 1:83 V

A passive network contains resistors, a 70-mH inductor, and a 25-mF capacitor. Obtain the respective s-domain impedances for a driving voltage (a) v ¼ 100 sin ð300t þ 458Þ ðVÞ, (b) v ¼ 100e100t cos 300t ðVÞ. (a) Resistance is independent of frequency.

At s ¼ j300 rad/s, the impedance of the inductor is

sL ¼ ð j300Þð70 103 Þ ¼ j21 and that of the capacitor is 1 ¼ j133:3 sC (b) At s ¼ 100 þ j300 s1 , sL ¼ ð100 þ j300Þð70 103 Þ ¼ 7 þ j21 1 1 ¼ ¼ 40 j120 sC ð100 þ j300Þð25 106 Þ

8.10

For the circuit shown in Fig. 8-20, obtain v at t ¼ 0:1 s for source current ðaÞ i ¼ 10 cos 2t (A), (b) i ¼ 10et cos 2t (A). Zin ðsÞ ¼ 2 þ (a) At s ¼ j2 rad/s, Zin ð j2Þ ¼ 3:22 7:138 .

2ðs þ 2Þ sþ3 ¼ ð4Þ sþ4 sþ4

Then,

V ¼ IZin ¼ ð10 08Þð3:22 7:138Þ ¼ 32:2 7:138 V

or

v ¼ 32:2 cos ð2t þ 7:138Þ

ðVÞ

and vð0:1Þ ¼ 32:2 cos ð18:598Þ ¼ 30:5 V. (b) At s ¼ 1 þ j2 s1 , Zin ð1 þ j2Þ ¼ 3:14 11:318 . V ¼ IZin ¼ 31:4 11:318 V

or

Then v ¼ 31:4et cos ð2t þ 11:318Þ

ðVÞ

and vð0:1Þ ¼ 31:4e0:1 cos 22:778 ¼ 26:2 V.

Fig. 8-20

8.11

Fig. 8-21

Obtain the impedance Zin ðsÞ for the circuit shown in Fig. 8-21 at (a) s ¼ 0, (c) jsj ¼ 1.

(b) s ¼ j4 rad/s,

180

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

4 s2 þ 3s þ 4 s Zin ðsÞ ¼ 2 þ ¼ ð2Þ 2 4 s þsþ2 2ðs þ 1Þ þ s 2ðs þ 1Þ

(a) Zin ð0Þ ¼ 4 , the impedance oﬀered to a constant (dc) source in the steady state. Zin ð j4Þ ¼ 2

ðbÞ

ð j4Þ2 þ 3ð j4Þ þ 4 ¼ 2:33 29:058 ð j4Þ2 þ j4 þ 2

This is the impedance oﬀered to a source sin 4t or cos 4t. (c)

8.12

Zin ð1Þ ¼ 2 .

At very high frequencies the capacitance acts like a short circuit across the RL branch.

Express the impedance ZðsÞ of the parallel combination of L ¼ 4 H and C ¼ 1 F. frequencies s is this impedance zero or inﬁnite? ZðsÞ ¼

At what

ð4sÞð1=sÞ s ¼ 4s þ ð1=sÞ s2 þ 0:25

By inspection, Zð0Þ ¼ 0 and Zð1Þ ¼ 0, which agrees with our earlier understanding of parallel LC circuits at frequencies of zero (dc) and inﬁnity. For jZðsÞj ¼ 1, s2 þ 0:25 ¼ 0

or

s ¼ j0:5 rad=s

A sinusoidal driving source, of frequency 0.5 rad/s, results in parallel resonance and an inﬁnite impedance.

8.13

The circuit shown in Fig. 8-22 has a voltage source connected at terminals ab. The response to the excitation is the input current. Obtain the appropriate network function HðsÞ. HðsÞ ¼ ZðsÞ ¼ 2 þ

response IðsÞ 1 ¼ excitation VðsÞ ZðsÞ

ð2 þ 1=sÞð1Þ 8s þ 3 ¼ 2 þ 1=s þ 1 3s þ 1

from which

HðsÞ ¼

Fig. 8-22

8.14

1 3s þ 1 ¼ ZðsÞ 8s þ 3

Fig. 8-23

Obtain HðsÞ for the network shown in Fig. 8-23, where the excitation is the driving current IðsÞ and the response is the voltage at the input terminals. Applying KCL at junction a,

IðsÞ þ 2IðsÞ ¼

s 0 V ðsÞ 5

or

V 0 ðsÞ ¼

15 IðsÞ s

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

181

At the input terminals, KVL gives 15 VðsÞ ¼ 2sIðsÞ þ V 0 ðsÞ ¼ 2s þ IðsÞ s Then

8.15

HðsÞ ¼

VðsÞ 2s2 þ 15 ¼ IðsÞ s

For the two-port network shown in Fig. 8-24 ﬁnd the values of R1 , R2 , and C, given that the voltage transfer function is Hv ðsÞ

Vo ðsÞ 0:2 ¼ Vi ðsÞ s2 þ 3s þ 2

Fig. 8-24 The impedance looking into xx 0 is Z0 ¼

ð1=sCÞðR1 þ R2 Þ R1 þ R2 ¼ ð1=sCÞ þ R1 þ R2 1 þ ðR1 þ R2 ÞCs

Then, by repeated voltage division, Vo Vo Vxx 0 R2 Z0 R2 =ðR1 þ R2 ÞC ¼ ¼ ¼ 0 1 2 Vi Vxx 0 Vi R1 þ R2 Z þ s1 s þ sþ 1 ðR1 þ R2 ÞC C Equating the coeﬃcients in this expression to those in the given expression for Hv ðsÞ, we ﬁnd: C¼

8.16

1 F 2

R1 ¼

3 5

R2 ¼

1 15

Construct the pole-zero plot for the transfer admittance function HðsÞ ¼

Io ðsÞ s2 þ 2s þ 17 ¼ 2 Vi ðsÞ s þ 3s þ 2

In factored form, HðsÞ ¼

ðs þ 1 þ j4Þðs þ 1 j4Þ ðs þ 1Þðs þ 2Þ

Poles exist at 1 and 2; zeros at 1 j4. See Fig. 8-25.

182

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Fig. 8-25

8.17

Obtain the natural frequencies of the network shown in Fig. 8-26 by driving it with a conveniently located current source.

Fig. 8-26 The response to a current source connected at xx 0 is a voltage across these same terminals; hence the network function HðsÞ ¼ VðsÞ=IðsÞ ¼ ZðsÞ. Then, 2 1 1 1 1 1 s þ 2:5s þ 1:5 ¼ þ þ ¼ ZðsÞ 1 2=s 2 þ 4s 2 s þ 0:5 Thus,

ZðsÞ ¼ ð2Þ

s þ 0:5 s þ 0:5 ¼ ð2Þ ðs þ 1Þðs þ 1:5Þ s2 þ 2:5s þ 1:5

The natural frequencies are the poles of the network function, s ¼ 1:0 Np=s ¼ 2 and s ¼ 1:5 Np/s.

8.18

Repeat Problem 8.17, now driving the network with a conveniently located voltage source. The conductor at yy 0 in Fig. 8-26 can be opened and a voltage source inserted. HðsÞ ¼ IðsÞ=VðsÞ ¼ 1=ZðsÞ: The impedance of the netework at terminals yy 0 is 1ð2=sÞ s2 þ 2:5s þ 1:5 ¼ ð4Þ 1 þ 2=s sþ2 1 1 sþ2 ¼ HðsÞ ¼ ZðsÞ 4 s2 þ 2:5s þ 1:5 ZðsÞ ¼ 2 þ 4s þ

Then;

Then,

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

183

The denominator is the same as that in Problem 8.17, with the same roots and corresponding natural frequencies.

8.19

A 5000-rad/s sinusoidal source, V ¼ 100 08 V in phasor form, is applied to the circuit of Fig. 8-27. Obtain the magnitude-scaling factor Km and the element values which will limit the current to 89 mA (maximum value). At ! ¼ 5000 rad/s, 1 ð j!L2 Þ R þ j!C Zin ¼ j!L1 þ 1 j!L2 þ R þ j!C ð j0:500Þð0:40 j0:80Þ ¼ 1:124 69:158 ¼ j0:250 þ 0:40 j0:30 For jVj ¼ 100 V, jIj ¼ 100=1:124 ¼ 89:0 A. Thus, to limit the current to 89 103 A, the impedance must be increased by the factor Km ¼ 103 . The scaled element values are as follows: R ¼ 103 ð0:4 Þ ¼ 400 , L1 ¼ 103 ð50 mHÞ ¼ 50 mH, L2 ¼ 103 ð100 mHÞ ¼ 100 mH, and C ¼ ð250 mFÞ=103 ¼ 0:250 mF.

Fig. 8-27

8.20

Refer to Fig. 8-28. Obtain HðsÞ ¼ Vo =Vi for s ¼ j4 106 rad/s. Km ¼ 103 and compare HðsÞ for the two networks.

Scale the network with

Fig. 8-28 At ! ¼ 4 106 rad/s, XL ¼ ð4 106 Þð0:5 103 Þ ¼ 2000 . HðsÞ ¼

Then,

Vo j2000 1 ¼ pﬃﬃﬃ ¼ Vi 2000 þ j2000 2

458

After magnitude scaling, the inductive reactance is 103 ð2000 Þ ¼ 2 and the resistance is 103 ð2 kÞ ¼ 2 . Thus HðsÞ ¼

j2 1 ¼ pﬃﬃﬃ 2 þ j2 2

458

184

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

The voltage transfer function remains unchanged by magnitude scaling. In general, any dimensionless transfer function is unaﬀected by magnitude scaling; a transfer function having units is multiplied by Km ; and a function having units S is multiplied by 1=Km .

8.21

A three-element series circuit contains R ¼ 5 , L ¼ 4 H, and C ¼ 3:91 mF. Obtain the series resonant frequency, in rad/s, and then frequency-scale the circuit with Kf ¼ 1000. Plot jZð!Þj for both circuits. Before scaling, 1 !0 ¼ pﬃﬃﬃﬃﬃﬃﬃ ¼ 8 rad=s LC

and

Zð!0 Þ ¼ R ¼ 5

After scaling, 4H ¼ 4 mH 1000 !0 ¼ 1000ð8 rad=sÞ ¼ 8000 rad=s

R ¼ 5

L¼

3:91 mF ¼ 3:91 mF 1000 Zð!0 Þ ¼ R ¼ 5

C¼

Fig. 8-29 Thus, frequency scaling by a factor of 1000 results in the 5- impedance value being attained at 8000 rad/s instead of 8 rad/s. Any other value of the impedance is likewise attained, after scaling, at a frequency 1000 times that at which it was attained before scaling. Consequently, the two graphs of jZð!Þj diﬀer only in the horizontal scale—see Fig. 8-29. (The same would be true of the two graphs of Zð!Þ .)

Supplementary Problems 8.22

In the RLC circuit of Fig. 8-30, the capacitor is initially charged to V0 ¼ 200 V. after the switch is closed at t ¼ 0. Ans: 2e1000t sin 1000t ðAÞ

Find the current transient

8.23

A series RLC circuit, with R ¼ 200 , L ¼ 0:1 H, and C ¼ 100 mF, has a voltage source of 200 V applied at t ¼ 0. Find the current transient, assuming zero initial charge on the capacitor. Ans: 1:055ðe52t e1948t Þ ðAÞ

8.24

What value of capacitance, in place of the 100 mF in Problem 8.23, results in the critically damped case? Ans: 10 mF

CHAP. 8]

185

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

Fig. 8-30

Fig. 8-31

8.25

Find the natural resonant frequency, jj, of a series RLC circuit with R ¼ 200 , L ¼ 0:1 H, C ¼ 5 mF. Ans: 1000 rad/s

8.26

A voltage of 10 V is applied at t ¼ 0 to a series RLC circuit with R ¼ 5 , L ¼ 0:1 H, C ¼ 500 mF. Find the transient voltage across the resistance. Ans: 3:60e25t sin 139t ðVÞ

8.27

In the two-mesh circuit shown in Fig. 8-31, the switch is closed at t ¼ 0. Find i1 and i2 , for t > 0. Ans: i1 ¼ 0:101e100t þ 9:899e9950t ðAÞ; i2 ¼ 5:05e100t þ 5:00 þ 0:05e9950t ðAÞ

8.28

A voltage has the s-domain representation 100 308 V. Express the time function for (a) s ¼ 2 Np/s, (b) s ¼ 1 þ j5 s1 . Ans: ðaÞ 86:6 e2t ðVÞ; ðbÞ 100 et cos ð5t þ 308Þ ðVÞ

8.29

Give the complex frequencies associated with the current iðtÞ ¼ 5:0 þ 10e3t cos ð50t þ 908Þ Ans: 0; 3 j50 s1

8.30

A phasor current 25 408 A has complex frequency s ¼ 2 þ j3 s1 . What is the magnitude of iðtÞ at t ¼ 0:2 s? Ans: 4:51 A

8.31

Calculate the impedance ZðsÞ for the circuit shown in Fig. 8-32, at (a) s ¼ 0; ðbÞ s ¼ j1 rad/s, (c) s ¼ j2 rad/s, (d) jsj ¼ 1. Ans: ðaÞ 1 ; ðbÞ 1:58 18:438 ; ðcÞ 1:84 12:538 ; ðdÞ 2

Fig. 8-32

8.32

Fig. 8-33

The voltage source in the s-domain circuit shown in Fig. 8-33 has the time-domain expression vi ðtÞ ¼ 10et cos 2t Obtain io ðtÞ.

8.33

ðAÞ.

Ans:

t

7:07e cos ð2t þ 98:138Þ

ðVÞ

ðAÞ

In the time domain, a series circuit of R, L, and C has an applied voltage vi and element voltages vR , vL , and vC . Obtain the voltage transfer functions (a) VR ðsÞ=Vi ðsÞ, (b) VC ðsÞ=Vi ðsÞ:

186

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

Ans:

8.34

ðaÞ

Rs=L ; R 1 s2 þ s þ L LC

ðbÞ

1=LC R 1 s2 þ s þ L LC

Obtain the network function HðsÞ for the circuit shown in Fig. 8-34. Ans:

[CHAP. 8

The response is the voltage Vi ðsÞ.

ðs þ 7 j2:65Þðs þ 7 þ j2:65Þ ðs þ 2Þðs þ 4Þ

Fig. 8-34 8.35

Construct the s-plane plot for the transfer function of Problem 8.34. Ans: See Fig. 8-35.

Evaluate Hð j3Þ from the plot.

ð7:02Þð9:0Þ 2:86 þ 38:918 ¼ 3:50 51:418 ð3:61Þð5:0Þ 56:318 þ 36:878

Fig. 8-35 8.36

Obtain HðsÞ ¼ Vi ðsÞ=Ii ðsÞ for the circuit shown in Fig. 8-36 and construct the pole-zero plot.

Ans:

8.37

HðsÞ ¼

sðs2 þ 1:5Þ : s2 þ 1

See Fig. 8-37.

Write the transfer function HðsÞ whose pole-zero plot is given in Fig. 8-38.

Ans:

HðsÞ ¼ k

s2 þ 50s þ 400 s2 þ 40s þ 2000

CHAP. 8]

Fig. 8-36 8.38

187

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

Fig. 8-37

The pole-zero plot in Fig. 8-39 shows a pole at s ¼ 0 and zeros at s ¼ 50 j50. method to evaluate the transfer function at the test point j100. Ans: Hð j100Þ ¼ 223:6 26:578

Fig. 8-38

Use the geometrical

Fig. 8-39

8.39

A two-branch parallel circuit has a resistance of 20 in one branch and the series combination of R ¼ 10 and L ¼ 0:1 H in the other. First, apply an excitation, Ii ðsÞ, and obtain the natural frequency from the denominator of the network function. Try diﬀerent locations for applying the current source. Second, insert a voltage source, Vi ðsÞ, and obtain the natural frequency. Ans: 300 Np/s in all cases

8.40

In the network shown in Fig. 8-40, the switch is closed at t ¼ 0.

At t ¼ 0þ , i ¼ 0 and

di ¼ 25 A=s dt Obtain the natural frequencies and the complete current, i ¼ in þ if . Ans: 8:5 Np/s, 23:5 Np/s; i ¼ 2:25e8:5t 0:25e23:5t þ 2:5 ðAÞ

188

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Fig. 8-40

8.41

A series RLC circuit contains R ¼ 1 , L ¼ 2 H, and C ¼ 0:25 F. Simultaneously apply magnitude and frequency scaling, with Km ¼ 2000 and Kf ¼ 104 . What are the scaled element values? Ans: 2000 ; 0:4 H; 12:5 mF

8.42

At a certain frequency !1 , a voltage V1 ¼ 25 08 V applied to a passive network results in a current I1 ¼ 3:85 308 (A). The network elements are magnitude-scaled with Km ¼ 10. Obtain the current which results from a second voltage source, V2 ¼ 10 458 V, replacing the ﬁrst, if the second source frequency is !2 ¼ 103 !1 . Ans: 0:154 158 A

8.43

In the circuit of Fig. 8-41 let R1 C1 ¼ R2 C2 ¼ 103 . Find v2 for t > 0 if: (a) v1 ¼ cos ð1000tÞuðtÞ, (b) v1 ¼ sin ð1000tÞuðtÞ. Ans: ðaÞ v2 ¼ sin ð1000tÞ; ðbÞ v2 ¼ 1 cos ð1000tÞ

8.44

In the circuit of Fig. 8-42 assume R ¼ 2 k, C ¼ 10 nF, and R2 ¼ R1 and v1 ¼ cos !t. following frequencies: (a) !0 ¼ 5 104 rad/s, (b) !1 ¼ 105 rad/s. Ans: ðaÞ v2 ¼ 2 sin !0 t; ðbÞ v2 ¼ 0:555 cos ð!1 t 146:38Þ

Fig. 8-41

Find v2 for the

Fig. 8-42

8.45

Noninverting integrators. In the circuits of Fig. 8-43(a) and 8-43(b) ﬁnd the relationship between v2 and v1 . Ans: ðaÞ v1 ¼ ðRC=2Þdv2 =dt; ðbÞ v1 ¼ 2RCdv2 =dt

8.46

In the circuit of Fig. 8-44 ﬁnd the relationship between v2 and v1 . v2 ¼ R2 v1 =ðR1 þ R2 Þ. Ans:

R1 R2 ðC1 þ C2 Þ

dv2 dv þ ðR1 þ R2 Þv2 ¼ R1 R2 C1 1 þ R2 v1 dt dt

Show that for R1 C1 ¼ R2 C2 we obtain

CHAP. 8]

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

189

Fig. 8-43 8.47

In the circuit of Fig. 8-44 let R1 ¼ 9 k ¼ 9R2 , C2 ¼ 100 pF ¼ 9C1 , and v1 ¼ 104 t V. the switch is closed. Ans: i ¼ 1:0001 mA

Find i at 1 ms after

Fig. 8-44

8.48

Lead network. The circuit of Fig. 8-45(a) is called a lead network. (a) Find the diﬀerential equation relating v2 to v1 . (b) Find the unit-step response of the network with R1 ¼ 10 k, R2 ¼ 1 k, and C ¼ 1 mF. (c) Let v1 ¼ cos !t be the input and v2 ¼ A cos ð!t þ Þ be the output of the network of Part (b). Find A and for ! at 1, 100, 331.6, 1100, and 105 , all in rad/s. At what ! is the phase at a maximum? dv2 R1 þ R2 dv 1 1 þ v ; ðbÞ v2 ¼ ð1 þ 10e1100t ÞuðtÞ Ans: ðaÞ v2 ¼ 1 þ dt R1 R2 C dt R1 C 1 11 (c) !

1

A

0.091

0.58

100 0.128 39:88

331.6 0.3015 56.48

1100 0.71 39.88

105 1 0.58

pﬃﬃﬃﬃﬃ Phase is maximum at ! ¼ 100 11 ¼ 331:6 rad/s 8.49

Lag network. The circuit of Fig. 8-45(b) is called a lag network. (a) Find the diﬀerential equation relating v2 to v1 . (b) Find the unit-step response of the network with R1 ¼ 10 k, R2 ¼ 1 k, and C ¼ 1 mF. (c) Let v1 ¼ cos !t be the input and v2 ¼ A cosð!t Þ be the output of the network of Part (b). Find A and for ! at 1, 90.9, 301.5, 1000, and 105 , all in rad/s. At what ! is the phase at a minimum? dv dv 10 90:91t e Ans: ðaÞ v2 þ ðR1 þ R2 ÞC 2 ¼ v1 þ R2 C 1 ; ðbÞ v2 ¼ 1 uðtÞ 11 dt dt

190

HIGHER-ORDER CIRCUITS AND COMPLEX FREQUENCY

[CHAP. 8

Fig. 8-45

(c)

!

1

90.9

301.5

1000

105

A

1

0.71

0.3015

0.128

0.091

0.58

39.88

56.48

39.88

0.58

pﬃﬃﬃﬃﬃ Phase is minimum at ! ¼ 1000= 11 ¼ 301:5 rad/s 8.50

In the circuit of Fig. 8-46 ﬁnd the relationship between v2 and v1 for (a) k ¼ 103 , case ﬁnd its unit-step response; that is, v2 for v1 ¼ uðtÞ. 6 dv2 þ 4 106 v2 ¼ 4 107 v1 ; v2 ¼ 10 1 e410 t uðtÞ Ans: ðaÞ dt 9 dv2 þ 4 108 v2 ¼ 4 109 v1 ; v2 ¼ 10 1 e410 t uðtÞ ðbÞ dt

Fig. 8-46

(b) k ¼ 105 .

In each

Sinusoidal SteadyState Circuit Analysis 9.1

INTRODUCTION

This chapter will concentrate on the steady-state response of circuits driven by sinusoidal sources. The response will also be sinusoidal. For a linear circuit, the assumption of a sinusoidal source represents no real restriction, since a source that can be described by a periodic function can be replaced by an equivalent combination (Fourier series) of sinusoids. This matter will be treated in Chapter 17.

9.2

ELEMENT RESPONSES

The voltage-current relationships for the single elements R, L, and C were examined in Chapter 2 and summarized in Table 2-1. In this chapter, the functions of v and i will be sines or cosines with the argument !t. ! is the angular frequency and has the unit rad/s. Also, ! ¼ 2f , where f is the frequency with unit cycle/s, or more commonly hertz (Hz). Consider an inductance L with i ¼ I cos ð!t þ 458Þ A [see Fig. 9-1(a)]. The voltage is vL ¼ L

di ¼ !LI½ sin ð!t þ 458Þ ¼ !LI cos ð!t þ 1358Þ dt

ðVÞ

Fig. 9-1

191 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

192

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

A comparison of vL and i shows that the current lags the voltage by 908 or =2 rad. The functions are sketched in Fig. 9-1(b). Note that the current function i is to the right of v, and since the horizontal scale is !t, events displaced to the right occur later in time. This illustrates that i lags v. The horizontal scale is in radians, but note that it is also marked in degrees (1358; 1808, etc.). This is a case of mixed units just as with !t þ 458. It is not mathematically correct but is the accepted practice in circuit analysis. The vertical scale indicates two diﬀerent quantities, that is, v and i, so there should be two scales rather than one. While examining this sketch, it is a good time to point out that a sinusoid is completely deﬁned when its magnitude ðV or IÞ, frequency (! or f ), and phase (458 or 1358) are speciﬁed. In Table 9-1 the responses of the three basic circuit elements are shown for applied current i ¼ I cos !t and voltage v ¼ V cos !t. If sketches are made of these responses, they will show that for a resistance R, v and i are in phase. For an inductance L, i lags v by 908 or =2 rad. And for a capacitance C, i leads v by 908 or =2 rad. Table 9-1 i ¼ I cos !t

v ¼ V cos !t

vr ¼ RI cos !t

iR ¼

V cos !t R

vL ¼ !LI cos ð!t þ 908Þ

iL ¼

V cosð!t 908Þ !L

vC ¼

I cos ð!t 908Þ !C

iC ¼ !CV cos ð!t þ 908Þ

EXAMPLE 9.1 The RL series circuit shown in Fig. 9-2 has a current i ¼ I sin !t. Obtain the voltage v across the two circuit elements and sketch v and i. di ¼ !LI sin ð!t þ 908Þ dt v ¼ vR þ vL ¼ RI sin !t þ !LI sin ð!t þ 908Þ

vR ¼ RI sin !t

vL ¼ L

Fig. 9-2 Since the current is a sine function and v ¼ V sin ð!t þ Þ ¼ V sin !t cos þ V cos !t sin

ð1Þ

v ¼ RI sin !t þ !LI sin !t cos 908 þ !LI cos !t sin 908

ð2Þ

we have from the above

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

193

Equating coeﬃcients of like terms in (1) and (2),

Then and

V sin ¼ !LI and V cos ¼ RI qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ v ¼ I R2 þ ð!LÞ2 sin ½!t þ arctan ð!L=RÞ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !L V ¼ I R2 þ ð!LÞ2 and ¼ tan1 R

The functions i and v are sketched in Fig. 9-3. The phase angle , the angle by which i lags v, lies within the range 08 908, with the limiting values attained for !L R and !L R, respectively. If the circuit had an applied voltage v ¼ V sin !t, the resulting current would be V i ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ sin ð!t Þ R2 þ ð!LÞ2 where, as before, ¼ tan1 ð!L=RÞ.

Fig. 9-3

EXAMPLE 9.2 If the current driving a series RC circuit is given by i ¼ I sin !t, obtain the total voltage across the two elements. vR ¼ RI sin !t

where

vC ¼ ð1=!CÞ sin ð!t 908Þ

v ¼ vR þ vC ¼ V sin ð!t Þ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ and ¼ tan1 ð1=!CRÞ V ¼ I R2 þ ð1=!CÞ2

The negative phase angle shifts v to the right of the current i. Consequently i leads v for a series RC circuit. The phase angle is constrained to the range 08 908. For ð1=!CÞ R, the angle ¼ 08, and for ð1=!CÞ R, the angle ¼ 908. See Fig. 9-4.

Fig. 9-4

194

9.3

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

PHASORS

A brief look at the voltage and current sinusoids in the preceding examples shows that the amplitudes and phase diﬀerences are the two principal concerns. A directed line segment, or phasor, such as that shown rotating in a counterclockwise direction at a constant angular velocity ! (rad/s) in Fig. 9-5, has a projection on the horizontal which is a cosine function. The length of the phasor or its magnitude is the amplitude or maximum value of the cosine function. The angle between two positions of the phasor is the phase diﬀerence between the corresponding points on the cosine function.

Fig. 9-5

Throughout this book phasors will be deﬁned from the cosine function. If a voltage or current is expressed as a sine, it will be changed to a cosine by subtracting 908 from the phase. Consider the examples shown in Table 9-2. Observe that the phasors, which are directed line segments and vectorial in nature, are indicated by boldface capitals, for example, V, I. The phase angle of the cosine function is the angle on the phasor. The phasor diagrams here and all that follow may be considered as a snapshot of the counterclockwise-rotating directed line segment taken at t ¼ 0. The frequency f (Hz) and ! (rad/s) generally do not appear but they should be kept in mind, since they are implicit in any sinusoidal steady-state problem. EXAMPLE 9.3 A series combination of R ¼ 10 and L ¼ 20 mH has a current i ¼ 5:0 cos ð500t þ 108) (A). Obtain the voltages v and V, the phasor current I and sketch the phasor diagram. Using the methods of Example 9.1, di ¼ 50:0 cos ð500t þ 1008Þ dt v ¼ vR þ vL ¼ 70:7 cos ð500t þ 558Þ ðVÞ

vR ¼ 50:0 cos ð500t þ 108Þ

vL ¼ L

The corresponding phasors are I ¼ 5:0

108 A

and

V ¼ 70:7

558 V

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

195

Table 9-2 Function

Phasor Representation

v ¼ 150 cos ð500t þ 458Þ

ðVÞ

i ¼ 3:0 sin ð2000t þ 308Þ ðmAÞ ¼ 3:0 cos ð2000t 608Þ

ðmAÞ

The phase angle of 458 can be seen in the time-domain graphs of i and v shown in Fig. 9-6(a), and the phasor diagram with I and V shown in Fig. 9-6(b).

Fig. 9-6

Phasors can be treated as complex numbers. When the horizontal axis is identiﬁed as the real axis of a complex plane, the phasors become complex numbers and the usual rules apply. In view of Euler’s identity, there are three equivalent notations for a phasor. polar form rectangular form

V¼V V ¼ Vðcos þ j sin Þ

exponential form

V ¼ Ve j

The cosine expression may also be written as v ¼ V cos ð!t þ Þ ¼ Re ½Ve jð!tþÞ ¼ Re ½Ve j!t The exponential form suggests how to treat the product and quotient of phasors. ðV1 e j1 ÞðV2 e j2 Þ þ V1 V2 e jð1 þ2 Þ , ðV1

1 ÞðV2

2 Þ ¼ V1 V2

1 þ 2

Since

196

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

and, since ðV1 e j1 Þ=ðV2 e j2 Þ ¼ ðV1 =V2 Þe jð1 2 Þ ; V1

1

V2

¼ V1 =V2

1 2

The rectangular form is used in summing or subtracting phasors. EXAMPLE 9.4 Given V1 ¼ 25:0

143:138 and V2 ¼ 11:2

26:578, ﬁnd the ratio V1 =V2 and the sum V1 þ V2 .

25:0 143:138 ¼ 2:23 116:568 ¼ 1:00 þ j1:99 11:2 26:578 V1 þ V2 ¼ ð20:0 þ j15:0Þ þ ð10:0 þ j5:0Þ ¼ 10:0 þ j20:0 ¼ 23:36 V1 =V2 ¼

9.4

116:578

IMPEDANCE AND ADMITTANCE

A sinusoidal voltage or current applied to a passive RLC circuit produces a sinusoidal response. With time functions, such as vðtÞ and iðtÞ, the circuit is said to be in the time domain, Fig. 9-7(a); and when the circuit is analyzed using phasors, it is said to be in the frequency domain, Fig. 9-7(b). The voltage and current may be written, respectively, vðtÞ ¼ V cos ð!t þ Þ ¼ Re ½Ve j!t iðtÞ ¼ I cos ð!t þ Þ ¼ Re ½Ie

j!t

and and

V¼V I¼I

The ratio of phasor voltage V to phasor current I is deﬁned as impedance Z, that is, Z ¼ V=I. The reciprocal of impedance is called admittance Y, so that Y ¼ 1=Z (S), where 1 S ¼ 1 1 ¼ 1 mho. Y and Z are complex numbers.

Fig. 9-7

When impedance is written in Cartesian form the real part is the resistance R and the imaginary part is the reactance X. The sign on the imaginary part may be positive or negative: When positive, X is called the inductive reactance, and when negative, X is called the capacitive reactance. When the admittance is written in Cartesian form, the real part is admittance G and the imaginary part is susceptance B. A positive sign on the susceptance indicates a capacitive susceptance, and a negative sign indicates an inductive susceptance. Thus, Z ¼ R þ jXL Y ¼ G jBL

and and

Z ¼ R jXC Y ¼ G þ jBC

The relationships between these terms follow from Z ¼ 1=Y. Then, G þ B2 R G¼ 2 R þ X2

R¼

G2

and and

B þ B2 X B¼ 2 R þ X2

X¼

G2

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

197

These expressions are not of much use in a problem where calculations can be carried out with the numerical values as in the following example. EXAMPLE 9.5 The phasor voltage across the terminals of a network such as that shown in Fig. 9-7(b) is 100:0 458 V and the resulting current is 5:0 158 A. Find the equivalent impedance and admittance. Z¼

V 100:0 458 ¼ 20:0 I 5:0 158

Y¼

I 1 ¼ ¼ 0:05 V Z

308 ¼ 17:32 þ j10:0

30 ¼ ð4:33 j2:50Þ 102 S

Thus, R ¼ 17:32 , XL ¼ 10:0 , G ¼ 4:33 102 S, and BL ¼ 2:50 102 S.

Combinations of Impedances The relation V ¼ IZ (in the frequency domain) is formally identical to Ohm’s law, v ¼ iR, for a resistive network (in the time domain). Therefore, impedances combine exactly like resistances: impedances in series

Zeq ¼ Z1 þ Z2 þ

impedances in parallel

1 1 1 ¼ þ þ Zeq Z1 Z2

In particular, for two parallel impedances, Zeq ¼ Z1 Z2 =ðZ1 þ Z2 Þ. Impedance Diagram In an impedance diagram, an impedance Z is represented by a point in the right half of the complex plane. Figure 9-8 shows two impedances; Z1 , in the ﬁrst quadrant, exhibits inductive reactance, while Z2 , in the fourth quadrant, exhibits capacitive reactance. Their series equivalent, Z1 þ Z2 , is obtained by vector addition, as shown. Note that the ‘‘vectors’’ are shown without arrowheads, in order to distinguish these complex numbers from phasors.

Fig. 9-8

Combinations of Admittances Replacing Z by 1/Y in the formulas above gives admittances in series

1 1 1 ¼ þ þ Yeq Y1 Y2

admittances in parallel

Yeq ¼ Y1 þ Y2 þ

Thus, series circuits are easiest treated in terms of impedance; parallel circuits, in terms of admittance.

198

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

Admittance Diagram Figure 9-9, an admittance diagram, is analogous to Fig. 9-8 for impedance. Shown are an admittance Y1 having capacitive susceptance and an admittance Y2 having inductive susceptance, together with their vector sum, Y1 þ Y2 , which is the admittance of a parallel combination of Y1 and Y2 .

Fig. 9-9

9.5

VOLTAGE AND CURRENT DIVISION IN THE FREQUENCY DOMAIN

In view of the analogy between impedance in the frequency domain and resistance in the time domain, Sections 3.6 and 3.7 imply the following results. (1) Impedances in series divide the total voltage in the ratio of the impedances: Vr Zr ¼ Vs Zs

or

Vr ¼

Zr V Zeq T

See Fig. 9-10.

Fig. 9-10

Fig. 9-11

(2) Impedances in parallel (admittances in series) divide the total current in the inverse ratio of the impedances (direct ratio of the admittances): Ir Zs Yr ¼ ¼ Is Zr Ys

or

Ir ¼

Zeq Y IT ¼ r IT Zr Yeq

See Fig. 9-11.

9.6

THE MESH CURRENT METHOD

Consider the frequency-domain network of Fig. 9-12. Applying KVL, as in Section 4.3, or simply by inspection, we ﬁnd the matrix equation

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

2

Z11 4 Z21 Z31

Z12 Z22 Z32

199

32 3 2 3 Z13 I1 V1 Z23 54 I2 5 ¼ 4 V2 5 Z33 I3 V3

for the unknown mesh currents I1 ; I2 ; I3 . Here, Z11 ZA þ ZB , the self-impedance of mesh 1, is the sum of all impedances through which I1 passes. Similarly, Z22 ZB þ ZC þ ZD and Z33 ZD þ ZE are the self-impedances of meshes 2 and 3.

Fig. 9-12

The 1,2-element of the Z-matrix is deﬁned as: X Z12 (impedance common to I1 and I2 Þ where a summand takes the plus sign if the two currents pass through the impedance in the same direction, and takes the minus sign in the opposite case. It follows that, invariably, Z12 ¼ Z21 . In Fig. 9-12, I1 and I2 thread ZB in opposite directions, whence Z12 ¼ Z21 ¼ ZB Similarly, Z13 ¼ Z31 Z23 ¼ Z23

X X

(impedance common to I1 and I3 Þ ¼ 0 (impedance common to I2 and I3 ¼ ZD

The Z-matrix is symmetric. In the V-column on the right-hand side of the equation, the entries Vk (k ¼ 1; 2; 3) are deﬁned exactly as in Section 4.3: X (driving voltage in mesh kÞ Vk where a summand takes the plus sign if the voltage drives in the direction of Ik , and takes the minus sign in the opposite case. For the network of Fig. 9-12, V1 ¼ þVa

V2 ¼ 0

V3 ¼ Vb

Instead of using the meshes, or ‘‘windows’’ of the (planar) network, it is sometimes expedient to choose an appropriate set of loops, each containing one or more meshes in its interior. It is easy to see that two loop currents might have the same direction in one impedance and opposite directions in another. Nevertheless, the preceding rules for writing the Z-matrix and the V-column have been formulated in such a way as to apply either to meshes or to loops. These rules are, of course, identical to those used in Section 4.3 to write the R-matrix and V-column. EXAMPLE 9.6 Suppose that the phasor voltage across ZB , with polarity as indicated in Fig. 9-13 is sought. Choosing meshes as in Fig. 9-12 would entail solving for both I1 and I2 , then obtaining the voltage as VB ¼ ðI2 I1 ÞZB . In Fig. 9-13 three loops (two of which are meshes) are chosen so as to make I1 the only current in ZB . Furthermore, the direction of I1 is chosen such that VB ¼ I1 ZB . Setting up the matrix equation:

200

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS 2

ZA þ ZB 4 ZA 0

[CHAP. 9

32 3 2 3 0 I1 Va ZD 54 I2 5 ¼ 4 Va 5 ZD þ ZE I3 Vb

ZA ZA þ ZC þ ZD ZD

from which Va ZB VB ¼ ZB I1 ¼ V z a Vb

ZA ZA þ ZB þ ZC ZD

0 ZD ZD þ ZE

where z is the determinant of the Z-matrix.

Fig. 9-13

Input and Transfer Impedances The notions of input resistance (Section 4.5) and transfer resistance (Section 4.6) have their exact counterparts in the frequency domain. Thus, for the single-source network of Fig. 9-14, the input impedance is Zinput;r

Vr z ¼ Ir rr

where rr is the cofactor of Zrr in z ; and the transfer impedance between mesh (or loop) r and mesh (loop) s is Ztransfer;rs

V r z ¼ Is rs

where rs is the cofactor of Zrs in z .

Fig. 9-14

As before, the superposition principle for an arbitrary n-mesh or n-loop network may be expressed as

Ik ¼

V1 Ztransfer;1k

þ þ

Vk1 Ztransfer;ðk1Þk

þ

Vk Zinput;k

þ

Vkþ1 Ztransfer;ðkþ1Þk

þ þ

Vn Ztransfer;nk

CHAP. 9]

9.7

201

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

THE NODE VOLTAGE METHOD

The procedure is exactly as in Section 4.4, with admittances replacing reciprocal resistances. A frequency-domain network with n principal nodes, one of them designated as the reference node, requires n 1 node voltage equations. Thus, for n ¼ 4, the matrix equation would be 2 32 3 2 3 V1 I1 Y11 Y12 Y13 4 Y21 Y22 Y23 54 V2 5 ¼ 4 I2 5 Y31 Y32 Y33 V3 I3 in which the unknowns, V1 , V2 , and V3 , are the voltages of principal nodes 1, 2, and 3 with respect to principal node 4, the reference node. Y11 is the self-admittance of node 1, given by the sum of all admittances connected to node 1. Similarly, Y22 and Y33 are the self-admittances of nodes 2 and 3. Y12 , the coupling admittance between nodes 1 and 2, is given by minus the sum of all admittances connecting nodes 1 and 2. It follows that Y12 ¼ Y21 . Similarly, for the other coupling admittances: Y13 ¼ Y31 , Y23 ¼ Y32 . The Y-matrix is therefore symmetric. On the right-hand side of the equation, the I-column is formed just as in Section 4.4; i.e., X (current driving into node kÞ ðk ¼ 1; 2; 3Þ Ik ¼ in which a current driving out of node k is counted as negative. Input and Transfer Admittances The matrix equation of the node voltage method, ½Y½V ¼ ½I is identical in form to the matrix equation of the mesh current method, ½Z½I ¼ ½V Therefore, in theory at least, input and transfer admittances can be deﬁned by analogy with input and transfer impedances: Yinput;r

Ir ¼ Y Vr rr

Ytransfer;rs

Ir ¼ Y Vs rs

where now rr and rs are the cofactors of Yrr and Yrs in Y . In practice, these deﬁnitions are often of limited use. However, they are valuable in providing an expression of the superposition principle (for voltages); Vk ¼

I1 Ytransfer;1k

þ þ

Ik1 Ytransfer;ðk1Þk

þ

Ik Yinput;k

þ

Ikþ1 Ytransfer;ðkþ1Þk

þ þ

In1 Ytransfer;ðnIfÞk

for k ¼ 1; 2; . . . ; n 1. In words: the voltage at any principal node (relative to the reference node) is obtained by adding the voltages produced at that node by the various driving currents, these currents acting one at a time.

9.8

THE´VENIN’S AND NORTON’S THEOREMS

These theorems are exactly as given in Section 4.9, with the open-circuit voltage V 0 , short-circuit current I 0 , and representative resistance R 0 replaced by the open-circuit phasor voltage V 0 , short-circuit phasor current I 0 , and representative impedance Z 0 . See Fig. 9-15.

202

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

Fig. 9-15

9.9

SUPERPOSITION OF AC SOURCES

How do we apply superposition to circuits with more than one sinusoidal source? If all sources have the same frequency, superposition is applied in the phasor domain. Otherwise, the circuit is solved for each source, and time-domain responses are added. EXAMPLE 9.7 A practical coil is connected in series between two voltage sources v1 ¼ 5 cos !1 t and v2 ¼ 10 cos ð!2 t þ 608Þ such that the sources share the same reference node. See Fig. 9-54. The voltage diﬀerence across the terminals of the coil is therefore v1 v2 . The coil is modeled by a 5-mH inductor in series with a 10- resistor. Find the current iðtÞ in the coil for (a) !1 ¼ !2 ¼ 2000 rad/s and (b) !1 ¼ 2000 rad/s, !2 ¼ 2!1 . pﬃﬃﬃ (a) The impedance of the coil is R þ jL! pﬃﬃﬃ¼ 10 þ j10 ¼ 10 2 458 . The phasor voltage between its terminals is V ¼ V1 V2 ¼ 5 10 608 ¼ j5 3 V. The current is pﬃﬃﬃ V j5 3 j8:66

¼ 0:61 1358 A I ¼ ¼ pﬃﬃﬃ Z 10 2 458 14:14 458 i ¼ 0:61 cos ð2000t 1358Þ

(b) Because the coil has diﬀerent impedances at !1 ¼ 2000 and !2 ¼ 4000 rad/s, the current may be represented in the time domain only. By applying superposition, we get i ¼ i1 i2 , where i1 and i2 are currents due to v1 and v2 , respectively. V1 5 ¼ 0:35 458 A; ¼ i1 ðtÞ ¼ 0:35 cos ð2000t 458Þ Z1 10 þ j10 V 10 608 ¼ 0:45 3:48 A; i2 ðtÞ ¼ 0:45 cos ð4000t 3:48Þ I2 ¼ 2 ¼ Z2 10 þ j20 i ¼ i1 i2 ¼ 0:35 cos ð2000t 458Þ 0:45 cos ð4000t 3:48Þ I1 ¼

Solved Problems 9.1

A 10-mH inductor has current i ¼ 5:0 cos 2000t (A). Obtain the voltage vL . From Table 9-1, vL ¼ !LI cos ð!t þ 908Þ ¼ 100 cos ð2000t þ 908Þ (V). vL ¼ 100 sin ð2000t þ 1808Þ ¼ 100 sin 2000t

9.2

As a sine function, ðVÞ

A series circuit, with R ¼ 10 and L ¼ 20 mH, has current i ¼ 2:0 sin 500t (A). Obtain total voltage v and the angle by which i lags v.

CHAP. 9]

203

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

By the methods of Example 9.1, 500ð20 103 Þ ¼ 458 ¼ arctan 10 qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ v ¼ I R2 þ ð!LÞ2 sin ð!t þ Þ ¼ 28:3 sin ð500t þ 458Þ

ðVÞ

It is seen that i lags v by 458.

9.3

Find the two elements in a series circuit, given that the current and total voltage are i ¼ 10 cos ð5000t 23:138Þ ðAÞ

v ¼ 50 cos ð5000t þ 308Þ

ðVÞ

Since i lags v (by 53.138), the elements are R and L. The ratio of Vmax to Imax is 50/10. qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 50 5000L and tan 53:138 ¼ 1:33 ¼ ¼ R2 þ ð5000LÞ2 10 R

Hence,

Solving, R ¼ 3:0 , L ¼ 0:8 mH.

9.4

A series circuit, with R ¼ 2:0 and C ¼ 200 pF, has a sinusoidal applied voltage with a frequency of 99.47MHz. If the maximum voltage across the capacitance is 24 V, what is the maximum voltage across the series combination? ! ¼ 2f ¼ 6:25 108 rad=s From Table 9-1, Imax ¼ !CVC;max ¼ 3:0 A. Then, by the methods of Example 9.2, qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Vmax ¼ Imax R2 þ ð1=!CÞ2 ¼ ð6Þ2 þ ð24Þ2 ¼ 24:74 V

9.5

The current in a series circuit of R ¼ 5 and L ¼ 30 mH lags the applied voltage by 808. Determine the source frequency and the impedance Z. From the impedance diagram, Fig. 9-16, 5 þ jXL ¼ Z

808

XL ¼ 5 tan 808 ¼ 28:4

3

Then 28:4 ¼ !ð30 10 Þ, whence ! ¼ 945:2 rad/s and f ¼ 150:4 Hz. Z ¼ 5 þ j28:4

Fig. 9-16

Fig. 9-17

204

9.6

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

At what frequency will the current lead the voltage by 308 in a series circuit with R ¼ 8 and C ¼ 30 mF? From the impedance diagram, Fig. 9-17, 8 jXC ¼ Z

1 4:62 ¼ 2f ð30 106 Þ

Then

9.7

XC ¼ 8 tan ð308Þ ¼ 4:62

308

or

f ¼ 1149 Hz

A series RC circuit, with R ¼ 10 , has an impedance with an angle of 458 at f1 ¼ 500 Hz. Find the frequency for which the magnitude of the impedance is (a) twice that at f1 , (b) one-half that at f1 . From 10 jXC ¼ Z1

458, XC ¼ 10 and Z1 ¼ 14:14 .

(a) For twice the magnitude, 10 jXC ¼ 28:28

or

8

XC ¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ð28:28Þ2 ð10Þ2 ¼ 26:45

or

f2 ¼ 189 Hz

Then, since XC is inversely proportional to f , 10 f ¼ 2 26:45 500

(b) A magnitude Z3 ¼ 7:07 is impossible; the smallest magnitude possible is Z ¼ R ¼ 10 .

9.8

A two-element series circuit has voltage V ¼ 240 08 V and current I ¼ 50 608 A. Determine the current which results when the resistance is reduced to (a) 30 percent, (b) 60 percent, of its former value. Z¼

V 240 08 ¼ ¼ 4:8 I 50 608

I1 ¼

240 08 ¼ 56:8 4:22 80:28

60% 2:40 ¼ 1:44

ðbÞ

I2 ¼

9.9

Z1 ¼ 0:72 þ j4:16 ¼ 4:22

30% 2:40 ¼ 0:72

ðaÞ

608 ¼ 2:40 þ j4:16

80:28

70:98

80:28 A

Z2 ¼ 1:44 þ j4:16 ¼ 4:40

240 08 ¼ 54:5 4:40 70:98

70:98 A

For the circuit shown in Fig. 9-18, obtain Zeq and compute I. For series impedances, Zeq ¼ 10 Then

9.10

08 þ 4:47

I¼

63:48 ¼ 12:0 þ j4:0 ¼ 12:65

V 100 08 ¼ ¼ 7:91 Zeq 12:65 18:438

18:438 A

Evaluate the impedance Z1 in the circuit of Fig. 9-19. Z¼

V ¼ 20 I

18:438

608 ¼ 10:0 þ j17:3

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

Fig. 9-18

205

Fig. 9-19

Then, since impedances in series add, 5:0 þ j8:0 þ Z1 ¼ 10:0 þ j17:3

9.11

or

Z1 ¼ 5:0 þ j9:3

Compute the equivalent impedance Zeq and admittance Yeq for the four-branch circuit shown in Fig. 9-20. Using admittances, 1 ¼ j0:20 S j5 1 Y2 ¼ ¼ 0:05 j0:087 S 5 þ j8:66 Y1 ¼

Then and

1 ¼ 0:067 S 15 1 Y4 ¼ ¼ j0:10 S j10

Y3 ¼

Yeq ¼ Y1 þ Y2 þ Y3 þ Y4 ¼ 0:117 j0:187 ¼ 0:221 Zeq ¼

1 ¼ 4:53 Yeq

58:08 S

58:08

Fig. 9-20

9.12

The total current I entering the circuit shown in Fig. 9-20 is 33:0 current I3 and the voltage V.

13:08 A. Obtain the branch

13:08Þð4:53 58:08Þ ¼ 149:5 45:08 V 1 I3 ¼ VY3 ¼ ð149:5 45:08Þ 08 ¼ 9:97 45:08 A 15 V ¼ IZeq ¼ ð33:0

9.13

Find Z1 in the three-branch network of Fig. 9-21, if I ¼ 31:5 V ¼ 50:0 60:08 V.

24:08 A for an applied voltage

206

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

Y¼ Then

I ¼ 0:630 V

36:08 ¼ 0:510 j0:370 S

0:510 j0:370 ¼ Y1 þ

whence Y1 ¼ 0:354

[CHAP. 9

1 1 þ 10 4:0 þ j3:0

458 S and Z1 ¼ 2:0 þ j2:0 .

Fig. 9-21

9.14

The constants R and L of a coil can be obtained by connecting the coil in series with a known resistance and measuring the coil voltage Vx , the resistor voltage V1 , and the total voltage VT (Fig. 9-22). The frequency must also be known, but the phase angles of the voltages are not

Fig. 9-22

known.

Fig. 9-23

Given that f ¼ 60 Hz, V1 ¼ 20 V, Vx ¼ 22:4 V, and VT ¼ 36:0 V, ﬁnd R and L.

The measured voltages are eﬀective values; but, as far as impedance calculations are concerned, it makes no diﬀerence whether eﬀective or peak values are used. The (eﬀective) current is I ¼ V1 =10 ¼ 2:0 A. Then Zx ¼

22:4 ¼ 11:2 2:0

Zeq ¼

36:0 ¼ 18:0 2:0

From the impedance diagram, Fig. 9-23, ð18:0Þ2 ¼ ð10 þ RÞ2 þ ð!LÞ2 ð11:2Þ2 ¼ R2 þ ð!LÞ2 where ! ¼ 260 ¼ 377 rad/s.

Solving simultaneously, R ¼ 4:92

9.15

L ¼ 26:7 mH

In the parallel circuit shown in Fig. 9-24, the eﬀective values of the currents are: Ix ¼ 18:0 A, I1 ¼ 15:0 A, IT ¼ 30:0 A. Determine R and XL .

CHAP. 9]

207

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

The problem can be solved in a manner similar to that used in Problem 9.14 but with the admittance diagram. The (eﬀective) voltage is V ¼ I1 ð4:0Þ ¼ 60:0 V. Then Yx ¼

Ix ¼ 0:300 S V

Yeq ¼

IT ¼ 0:500 S V

Y1 ¼

Fig. 9-24

1 ¼ 0:250 S 4:0

Fig. 9-25

From the admittance diagram, Fig. 9-25, ð0:500Þ2 ¼ ð0:250 þ GÞ2 þ B2L ð0:300Þ2 ¼ G2 þ B2L which yield G ¼ 0:195 S, BL ¼ 0:228 S. Then R¼

1 ¼ 5:13 G

and

jXL ¼

1 ¼ j4:39 jBL

i.e., XL ¼ 4:39 .

9.16

Obtain the phasor voltage VAB in the two-branch parallel circuit of Fig. 9-26. By current-division methods, I1 ¼ 4:64 120:18 A and I2 ¼ 17:4 AYB may be considered. Choosing the former, VAB ¼ VAX þ VXB ¼ I1 ð20Þ I2 ð j6Þ ¼ 92:8

120:18 þ 104:4

Fig. 9-26

9.17

30:18 A. Either path AXB or path 59:98 ¼ 11:6

59:98 V

Fig. 9-27

In the parallel circuit shown in Fig. 9-27, VAB ¼ 48:3

308 V.

Find the applied voltage V.

By voltage division in the two branches: j4 1 j8:66 V¼ V VBX ¼ V 4 j4 1þj 5 þ j8:66 1 j8:66 1 V¼ V VBX ¼ 1 þ j 5 þ j8:66 0:268 þ j1

VAX ¼ and so or

VAB ¼ VAX

V ¼ ð0:268 þ j1ÞVAB ¼ ð1:035

1058Þð48:3

308Þ ¼ 50:0

1358

V

208

9.18

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

Obtain the voltage Vx in the network of Fig. 9-28, using the mesh current method.

Fig. 9-28 One choice of mesh currents is shown on the circuit diagram, with I3 passing through the 10- resistor in a direction such that Vx ¼ I3 ð10Þ (V). The matrix equation can be written by inspection: 3 2 32 3 2 7 þ j3 j5 5 I1 10 08 6 7 4 j5 12 þ j3 ð2 j2Þ 54 I2 5 ¼ 4 5 308 5 I3 5 ð2 j2Þ 17 j2 0 Solving by determinants, 7 þ j3 j5 10 08 j5 12 þ j3 5 308 5 2 þ j2 0 667:96 169:098 ¼ 0:435 I3 ¼ ¼ 7 þ j3 j5 5 1534:5 25:068 j5 12 þ j3 2 þ j2 5 2 þ j2 17 j2 and Vx ¼ I3 ð10Þ ¼ 4:35

9.19

194:158 A

194:158 V.

In the netwrok of Fig. 9-29, determine the voltage V which results in a zero current through the 2 þ j3 impedance.

Fig. 9-29

CHAP. 9]

209

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

Choosing mesh currents as shown on the circuit diagram, 5 þ j5 30 08 0 1 I2 ¼ j5 0 6 ¼0 z 0 V 10 Expanding the numerator determinant by cofactors of the second column, j5 6 V 5 þ j5 0 ¼ 0 whence V ¼ 35:4 ð30 08Þ j5 6 0 10

9.20

45:08 V

Solve Problem 9.19 by the node voltage method. The network is redrawn in Fig. 9-30 with one end of the 2 þ j3 impedance as the reference node. By the rule of Section 9.7 the matrix equation is 2 32 3 2 3 1 1 1 1 1 V1 30 08 þ þ þ 6 5 j5 2 þ j3 7 7 6 5 j5 7 5 6 76 7 7¼6 6 76 4 4 5 4 1 1 1 1 1 15 30 08 V 5 þ þ þ þ V2 5 j5 5 j5 4 6 5 4 For node voltage V1 to be zero, it is necessary that the numerator determinant in the solution for V1 vanish. 30 08 0:200 þ j0:200 5 ¼0 from which V ¼ 35:4 458 V N1 ¼ 30 08 V 0:617 j0:200 5 4

Fig. 9-30

9.21

Fig. 9-31

Use the node voltage method to obtain the current I in the network of Fig. 9-31. There are three principal nodes in the network. The reference and node 1 are selected so that the node 1 voltage is the voltage across the j2- reactance. 21

32 3 2 3 1 1 1 V1 50 08 þ 6 5 j2 4 76 7 6 7 4 5 6 76 7 ¼ 6 7 4 1 1 1 1 54 5 4 50 908 5 þ þ V2 4 4 j2 2 2 from which

þ

210

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

10 j25

0:250 13:52 56:318 0:750 þ j0:500 ¼ ¼ 24:76 V1 ¼ 0:450 j0:500 0:546 15:948 0:250 0:250 0:750 þ j0:500 and

9.22

I¼

24:76 72:258 ¼ 12:38 2 908

72:258 V

17:758 A

Find the input impedance at terminals ab for the network of Fig. 9-32.

Fig. 9-32 With mesh current I1 selected as shown on the diagram. 8 j2 3 0 3 8 þ j5 5 0 5 7 j2 315:5 16:198 ¼ 6:98 Zinput;1 ¼ z ¼ ¼ 8 þ j5 5 11 45:2 24:868 5 7 j2

9.23

For the network in Fig. 9-32, obtain the current in the inductor, Ix , by ﬁrst obtaining the transfer impedance. Let V ¼ 10 308 V. Ztransfer;12 ¼

Then

9.24

8:678

Ix ¼ I2 ¼

z 315:5 16:198 ¼ 14:45 ¼ 3 5 12 0 7 j2

V 10 ¼ Ztransfer;12 14:45

32:148

308 ¼ 0:692 32:148

2:148 A

For the network in Fig. 9-32, ﬁnd the value of the source voltage V which results in V0 ¼ 5:0 08 V. The transfer impedance can be used to compute the current in the 2 j2 impedance, from which V0 is readily obtained. Ztransfer;13 ¼

z 315:5 16:198 ¼ ¼ 21:0 13 15 08

V0 ¼ I3 ð2 j2Þ ¼

16:198

V ð2 j2Þ ¼ Vð0:135 Ztransfer;13

61:198Þ

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

Thus, if V0 ¼ 5:0

211

08 V, V¼

5:0 08 ¼ 37:0 0:135 61:198

61:198 V

Alternate Method The node voltage method may be used. V0 is the node voltage V2 for the selection of nodes indicated in Fig. 9-32. 1 1 1 V þ þ 5 j2 3 j5 5 j2 1 0 j5 ¼ Vð0:134 61:158Þ V0 ¼ V2 ¼ 1 1 þ1þ 1 5 j2 3 j5 j5 1 1 1 1 þ þ j5 j5 5 2 j2 For V0 ¼ 5:0

9.25

08 V, V ¼ 37:3

61:158 V, which agrees with the previous answer to within roundoﬀ errors.

For the network shown in Fig. 9-33, obtain the input admittance and use it to compute node voltage V1 .

Yinput;1

1 1 þ 1 þ1 10 j5 2 2 1 1 1 1 þ þ Y 2 2 3 þ j4 j10 ¼ 0:311 ¼ ¼ 1 1 1 11 þ þ 2 3 þ j4 j10 V1 ¼

I1 5:0 08 ¼ 16:1 ¼ Yinput;1 0:311 49:978

49:978 S

49:978 V

Fig. 9-33

9.26

For the network of Problem 9.25, compute the transfer admittance Ytransfer;12 and use it to obtain node voltage V2 .

Y 0:194 55:498 ¼ ¼ 0:388 12 ð0:50Þ I1 ¼ 12:9 55:498 V V2 ¼ Ytransfer;12

Ytransfer;12 ¼

55:498 S

212

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

9.27

Replace the active network in Fig. 9-34(a) at terminals ab with a The´venin equivalent. Z 0 ¼ j5 þ

5ð3 þ j4Þ ¼ 2:50 þ j6:25 5 þ 3 þ j4

[CHAP. 9

The open-circuit voltage V 0 at terminals ab is the voltage across the 3 þ j4 impedance: V0 ¼

10 08 ð3 þ j4Þ ¼ 5:59 8 þ j4

26:568 V

Fig. 9-34

9.28

For the network of Problem 9.27, obtain a Norton equivalent circuit (Fig. 9-35). At terminals ab, Isc is the Norton current I 0 . By current division, 10 08 3 þ j4 ¼ 0:830 41:638 A I0 ¼ j5ð3 þ j4Þ 3 þ j9 5þ 3 þ j9

Fig. 9-35

Fig. 9-36

The shunt impedance Z 0 is as found in Problem 9.27, Z 0 ¼ 2:50 þ j6:25 .

9.29

Obtain the The´venin equivalent for the bridge circuit of Fig. 9-36. Make V 0 the voltage of a with respect to b. By voltage division in either branch,

Vax ¼

12 þ j24 ð20 33 þ j24

08Þ

Vbx ¼

30 þ j60 ð20 80 þ j60

08Þ

CHAP. 9]

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

Hence,

Vab ¼ Vax Vbx ¼ ð20

12 þ j24 30 þ j60 08Þ ¼ 0:326 33 þ j24 80 þ j60

213

169:48 V ¼ V 0

Viewed from ab with the voltage source shorted out, the circuit is two parallel combinations in series, and so Z0 ¼

9.30

21ð12 þ j24Þ 50ð30 þ j60Þ þ ¼ 47:35 33 þ j24 80 þj60Þ

26:818

Replace the network of Fig. 9-37 at terminals ab with a Norton equivalent and with a The´venin equivalent.

Fig. 9-37 By current division, 2

3 6 7 3 þ j4 10 08 7 Isc ¼ I 0 ¼ 6 ¼ 0:439 4 5 ðj10Þð3 þ j4Þ 3 j6 10 þ 3 j6

105:268 A

and by voltage division in the open circuit, Vab ¼ V 0 ¼

Then

Z0 ¼

3 þ j4 ð10 13 þ j4

V0 3:68 ¼ I0 0:439

08Þ ¼ 3:68

36:038 ¼ 8:37 105:268

See Fig. 9-38.

Fig. 9-38

36:038 V

69:238

214

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

Supplementary Problems 9.31

Two circuit elements in a series connection have current and total voltage i ¼ 13:42 sin ð500t 53:48Þ Identify the two elements.

9.32

Ans:

v ¼ 150 sin ð500t þ 108Þ

ðAÞ

ðVÞ

R ¼ 5 ; L ¼ 20 mH

Two circuit elements in a series connection have current and total voltage i ¼ 4:0 cos ð2000t þ 13:28Þ Identify the two elements.

Ans:

v ¼ 200 sin ð2000t þ 50:08Þ

ðAÞ

ðVÞ

R ¼ 30 ; C ¼ 12:5 mF

9.33

A series RC circuit, with R ¼ 27:5 and C ¼ 66:7 mF, has sinusoidal voltages and current, with angular frequency 1500 rad/s. Find the phase angle by which the current leads the voltage. Ans: 208

9.34

A series RLC circuit, with R ¼ 15 , L ¼ 80 mH, and C ¼ 30 mF, has a sinusoidal current at angular frequency 500 rad/s. Determine the phase angle and whether the current leads or lags the total voltage. Ans: 60:68, leads

9.35

A capacitance C ¼ 35 mF is in parallel with a certain element. Identify the element, given that the voltage and total current are v ¼ 150 sin 3000t ðVÞ Ans:

iT ¼ 16:5 sin ð3000t þ 72:48Þ

ðAÞ

R ¼ 30:1

9.36

A two-element series circuit, with R ¼ 20 and L ¼ 20 mH, has an impedance 40:0 angle and the frequency. Ans: 608; 276 Hz

9.37

Determine the impedance of the series RL circuit, with R ¼ 25 and L ¼ 10 mH, at (a) 100 Hz, (b) 500 Hz, (c) 1000 Hz. Ans: ðaÞ 25:8 14:18 ; ðbÞ 40:1 51:58 ; ðcÞ 67:6 68:38

9.38

Determine the circuit constants of a two-element series circuit if the applied voltage v ¼ 150 sin ð5000t þ 458Þ results in a current i ¼ 3:0 sin ð5000t 158Þ (A).

9.39

9.40

9.41

Ans:

. Determine the

ðVÞ

25 ; 8:66 mH

A series circuit of R ¼ 10 and p Cﬃﬃﬃ¼ 40 mF has an applied voltage v ¼ 500 cos ð2500t 208Þ (V). Find the resulting current i. Ans: 25 2 cos ð2500t þ 258Þ (A) pﬃﬃﬃ Three impedances are in series: Z1 ¼ 3:0 458 , Z2 ¼ 10 2 458 , Z3 ¼ 5:0 908 . Find the applied voltage V, if the voltage across Z1 is 27:0 108 V. Ans: 126:5 24:68 V For the three-element series circuit in Fig. 9-39, (a) ﬁnd the current I; (b) ﬁnd the voltage across each impedance and construct the voltage phasor diagram which shows that V1 þ V2 þ V3 ¼ 100 08 V. Ans: ðaÞ 6:28 9:178 A; (bÞ see Fig. 9-40.

Fig. 9-39

CHAP. 9]

215

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

Fig. 9-40 9.42

Find Z in the parallel circuit of Fig. 9-41, if V ¼ 50:0 Ans: 5:0 308

30:08 V and I ¼ 27:9

57:88 A.

Fig. 9-41 2058 V and a resulting

9.43

Obtain the conductance and susceptance corresponding to a voltage V ¼ 85:0 current I ¼ 41:2 141:08 A. Ans: 0:471 S; 0:117 S (capacitive)

9.44

A practical coil contains resistance as well as inductance and can be represented by either a series or parallel circuit, as suggested in Fig. 9-42. Obtain Rp and Lp in terms of Rs and Ls . Ans:

Rp ¼ Rs þ

ð!Ls Þ2 R2 ; Lp ¼ Ls þ 2 s Rs ! Ls

Fig. 9-42 9.45

In the network shown in Fig. 9-43 the 60-Hz current magnitudes are known to be: IT ¼ 29:9 A, I1 ¼ 22:3 A, and I2 ¼ 8:0 A. Obtain the circuit constants R and L. Ans: 5:8 ; 38:5 mH

Fig. 9-43

Fig. 9-44

216

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

[CHAP. 9

9.46

Obtain the magnitude of the voltage VAB in the two-branch parallel network of Fig. 9-44, if XL is (a) 5 , (b) 15 , ðcÞ 0 . Ans: 50 V, whatever XL

9.47

In the network shown in Fig. 9-45, VAB ¼ 36:1 Ans: 75 908 V

3:188 V. Find the source voltage V.

Fig. 9-45

Fig. 9-46

9.48

For the network of Fig. 9-46 assign two diﬀerent sets of mesh currents and show that for each, z ¼ 55:9 26:578 2 . For each choice, calculate the phasor voltage V. Obtain the phasor voltage across the 3 þ j4 impedance and compare with V. Ans: V ¼ V3þj4 ¼ 22:36 10:308 V

9.49

For the network of Fig. 9-47, use the mesh current method to ﬁnd the current in the 2 þ j3 impedance due Ans: 2:41 6:458 A; 1:36 141:458 A to each of the sources V1 and V2 .

Fig. 9-47

9.50

In the network shown in Fig. 9-48, the two equal capacitances C and the shunting resistance R are adjusted until the detector current ID is zero. Assuming a source angular frequency !, determine the values of Rx and Lx . Ans: Rx ¼ 1=ð!2 C 2 RÞ; Lx ¼ 1=ð2!CÞ

Fig. 9-48

CHAP. 9]

9.51

217

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

For the network of Fig. 9-49, obtain the current ratio I1 =I3 .

Ans:

3:3

908

Fig. 9-49

9.52

For the network of Fig. 9-49, obtain Zinput;1 and Ztransfer;13 . Ans: 1:31 21:88 ; 4:31 68:28

9.53

In the network of Fig. 9-50, obtain the voltage ratio V1 =V2 by application of the node voltage method. Ans:

9.54

11 ¼ 1:61 12

Show that Ztransfer;31 ¼ Ztransfer;13 .

29:88

For the network of Fig. 9-50, obtain the driving-point impedance Zinput;1 .

Fig. 9-50

Ans:

5:59

17:358

Fig. 9-51

9.55

Obtain the The´venin and Norton equivalent circuits at terminals ab for the network of Fig. 9-51. Choose the polarity such that V 0 ¼ Vab . Ans: V 0 ¼ 20:0 08 V; I 0 ¼ 5:56 23:068 A; Z 0 ¼ 3:60 23:068

9.56

Obtain the The´venin and Norton equivalent circuits at terminals ab for the network of Fig. 9-52. Ans: V 0 ¼ 11:5 95:88 V; I 0 ¼ 1:39 80:68 A; Z 0 ¼ 8:26 15:28

Fig. 9-52

Fig. 9-53

218

SINUSOIDAL STEADY-STATE CIRCUIT ANALYSIS

9.57

Obtain the The´veinin and Norton equivalent circuits at terminals ab for the network of Fig. 9-53. Ans: V 0 ¼ 11:18 93:438 V; I 0 ¼ 2:24 56:568 A; Z 0 ¼ 5:0 36:878

9.58

In the circuit of Fig. 9-54, v1 ¼ 10 V and v2 ¼ 5 sin 2000t. Ans: i ¼ 1 0:35 sin ð2000t 458Þ

[CHAP. 9

Find i.

Fig. 9-54

Fig. 9-55

9.59

In the circuit of Fig. 9-55, v1 ¼ 6 cos !t and v2 ¼ cos ð!t þ 608). Find vA if ! ¼ 2 rad/sec. KCL at node A in the phasor domain. Ans: vA ¼ 1:11 sin 2t

Hint: Apply

9.60

In the circuit of Problem 9.59 ﬁnd phasor currents I1 and I2 drawn from the two sources. phasor KVL to the loops on the left and right sides of the circuit. Ans: I1 ¼ 508 100:48; I2 ¼ 1057 1458, both in mA

Hint: Apply

9.61

Find vA in the circuit of Problem 9.59 if ! ¼ 0:5 rad/s.

9.62

In the circuit of Fig. 9-55, v1 ¼ V1 cos ð0:5t þ 1 Þ and v2 ¼ V2 cosð0:5t þ 2 Þ. Find the current through the 4 H inductor. Ans: i ¼ ðV2 =4Þ sin ð0:5t þ 2 Þ ðV1 =3Þ sin ð0:5t þ 1 Þ

9.63

In the circuit of Fig. 9-55, v1 ¼ V1 cos ðt þ 1 Þ and v2 ¼ V2 cos ðt þ 2 Þ. Ans: vA ¼ 1, unless V1 ¼ V2 ¼ 0, in which case vA ¼ 0

9.64

In the circuit of Fig. 9-55, v1 ¼ V1 cos ð2tÞ and v2 ¼ V2 cos ð0:25tÞ. Ans: vA ¼ 0:816V1 cos ð2tÞ 0:6V2 cos ð0:25tÞ

Ans:

Va ¼ 0

Find vA .

Find vA .

AC Power 10.1

POWER IN THE TIME DOMAIN The instantaneous power entering a two-terminal circuit N (Fig. 10-1) is deﬁned by pðtÞ ¼ vðtÞiðtÞ

ð1Þ

where vðtÞ and iðtÞ are terminal voltage and current, respectively. If p is positive, energy is delivered to the circuit. If p is negative, energy is returned from the circuit to the source.

Fig. 10-1

In this chapter, we consider periodic currents and voltages, with emphasis on the sinusoidal steady state in linear RLC circuits. Since the storage capacity of an inductor or a capacitor is ﬁnite, these passive elements cannot continue receiving energy without returning it. Therefore, in the steady state and during each cycle, all of the energy received by an inductor or capacitor is returned. The energy received by a resistor is, however, dissipated in the form of thermal, mechanical, chemical, and/or electromagnetic energies. The net energy ﬂow to a passive circuit during one cycle is, therefore, positive or zero. EXAMPLE 10.1 Figure 10-2(a) shows the graph of a current in a resistor of 1 k. Find and plot the instantaneous power pðtÞ. From v ¼ Ri, we have pðtÞ ¼ vi ¼ Ri2 ¼ 1000 106 ¼ 103 W ¼ 1 mW. See Fig. 10-2(b). EXAMPLE 10.2 The current in Example 10.1 passes through a 0.5-mF capacitor. Find the power pðtÞ entering the capacitor and the energy wðtÞ stored in it. Assume vC ð0Þ ¼ 0. Plot pðtÞ and wðtÞ. Figure 10-2(a) indicates that the current in the capacitor is a periodic function with a period T ¼ 2 ms. During one period the current is given by 1 mA ð0 < t < 1 msÞ i¼ 1 mA ð1 < t < 2 msÞ

219 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

220

AC POWER

[CHAP. 10

Fig. 10-2 The voltage across the capacitor is also a periodic function with the same period T [Fig. 10-3(a)]. period the voltage is ð 1 t 2000t ðVÞ ð0 < t < 1 msÞ vðtÞ ¼ i dt ¼ 4 2000t ðVÞ ð1 < t < 2 msÞ C 0

During one

Finally, the power entering the capacitor and the energy stored in it (both also periodic with period T) are 2000t ðmWÞ ð0 < t < 1 msÞ pðtÞ ¼ vi ¼ ½Fig. 10-3ðbÞ 2000t 4 ðmWÞ ð1 < t < 2 msÞ ( 1 t2 ðJÞ ð0 < t < 1 msÞ [Fig. 10-3ðcÞ wðtÞ ¼ Cv2 ¼ 2 2 t þ 4 106 4 103 t ðJÞ ð1 < t < 2 msÞ Alternatively, wðtÞ may be obtained by integrating pðtÞ. Power entering the capacitor during one period is equally positive and negative [see Fig. 10-3(b)]. The energy stored in the capacitor is always positive as shown in Fig. 103(c). The maximum stored energy is Wmax ¼ 106 J ¼ 1 mJ at t ¼ 1; 3; 4; . . . ms.

10.2

POWER IN SINUSOIDAL STEADY STATE

A sinusoidal voltage v ¼ Vm cos !t, applied across an impedance Z ¼ jZj , establishes a current i ¼ Im cos ð!t Þ. The power delivered to the impedance at time t is pðtÞ ¼ vi ¼ Vm Im cos !t cos ð!t Þ ¼ 12 Vm Im ½cos þ cos ð2!t Þ ¼ Veff Ieff ½cos þ cos ð2!t Þ ¼ Veff Ieff cos þ Veff Ieff cos ð2!t Þ ð2Þ pﬃﬃﬃ pﬃﬃﬃ where Veff ¼ Vm = 2, Ieff ¼ Im = 2, and Ieff ¼ Veff =jZj. The instantaneous power in (2) consists of a sinusoidal component Veff Ieff cos ð2!t Þ plus a constant value Veff Ieff cos which becomes the average power Pavg . This is illustrated in Fig. 10-4. During a portion of one cycle, the instantaneous power is positive which indicates that the power ﬂows into the load. During the rest of the cycle, the instan-

CHAP. 10]

221

AC POWER

Fig. 10-3

taneous power may be negative, which indicates that the power ﬂows out of the load. of power during one cycle is, however, nonnegative and is called the average power. EXAMPLE 10.3 A voltage v ¼ 140 cos !t is connected across an impedance Z ¼ 5 608. The voltage v results in a current i ¼ 28 cos ð!t þ 608Þ. Then,

The net ﬂow

Find pðtÞ.

pðtÞ ¼ vi ¼ 140ð28Þ cos !t cos ð!t þ 608Þ ¼ 980 þ 1960 cos ð2!t þ 608Þ The instantaneous power has a constant component of 980 W and a sinusoidal component with twice the frequency of the source. The plot of p vs. t is similar to that in Fig. 10-4 with ¼ =3.

10.3

AVERAGE OR REAL POWER

The net or average power Pavg ¼ hpðtÞi entering a load during one period is called the real power. Since the average of cos ð2!t Þ over one period is zero, from (2) we get Pavg ¼ Veff Ieff cos

ð3Þ

222

AC POWER

[CHAP. 10

Fig. 10-4

If Z ¼ R þ jX ¼ jZj , then cos ¼ R=jZj and Pavg may be expressed by Pavg ¼ Veff Ieff or

Pavg ¼

R jZj

ð4Þ

2 Veff R jZj2

(5)

2 Pavg ¼ RIeff

or

(6)

The average power is nonnegative. It depends on V, I, and the phase angle between them. When Veff and Ieff are given, P is maximum for ¼ 0. This occurs when the load is purely resistive. For a purely reactive load, jj ¼ 908 and Pavg ¼ 0. The ratio of Pavg to Veff Ieff is called the power factor pf. From (3), the ratio is equal to cos and so pf ¼

Pavg Veff Ieff

0 pf 1

ð7Þ

The subscript avg in the average power Pavg is often omitted and so in the remainder of this chapter P will denote average power. EXAMPLE 10.4 Find P delivered from a sinusoidal voltage source with Veff ¼ 110 V to an impedance of Z ¼ 10 þ j8. Find the power factor. Z ¼ 10 þ j8 ¼ 12:81 38:78 Ieff

V 110 ¼ eff ¼ ¼ 8:59 38:78 A Z 12:81 38:78

P ¼ Veff Ieff cos ¼ 110ð8:59 cos 38:78Þ ¼ 737:43 pf ¼ cos 38:78 ¼ 0:78

W

CHAP. 10]

223

AC POWER

Alternative Solution We have jZj2 ¼ 100 þ 64 ¼ 164.

Then,

2 P ¼ Veff R=jZj2 ¼ 1102 ð10Þ=164 ¼ 737:8 W

The alternative solution gives a more accurate answer.

10.4

REACTIVE POWER

If a passive network contains inductors, capacitors, or both, a portion of energy entering it during one cycle is stored and then returned to the source. During the period of energy return, the power is negative. The power involved in this exchange is called reactive or quadrature power. Although the net eﬀect of reactive power is zero, it degrades the operation of power systems. Reactive power, indicated by Q, is deﬁned as Q ¼ Veff Ieff sin

ð8Þ

If Z ¼ R þ jX ¼ jZj , then sin ¼ X=jZj and Q may be expressed by Q ¼ Veff Ieff or

Q¼

X jZj

2 Veff X jZj2

(10)

2 Q ¼ XIeff

or

ð9Þ

(11)

The unit of reactive power is the volt-amperes reactive (var). The reactive power Q depends on V, I, and the phase angle between them. It is the product of the voltage and that component of the current which is 908 out of phase with the voltage. Q is zero for ¼ 08. This occurs for a purely resistive load, when V and I are in phase. When the load is purely reactive, jj ¼ 908 and Q attains its maximum magnitude for given V and I. Note that, while P is always nonnegative, Q can assume positive values (for an inductive load where the current lags the voltage) or negative values (for a capacitive load where the current leads the voltage). It is also customary to specify Q by it magnitude and load type. For example, 100-kvar inductive means Q ¼ 100 kvar and 100-kvar capacitive indicates Q ¼ 100 kvar. EXAMPLE 10.5 and Q.

The voltage and current across a load are given by Veff ¼ 110 V and Ieff ¼ 20 508 A. P ¼ 110ð20 cos 508Þ ¼ 1414 W

10.5

Find P

Q ¼ 110ð20 sin 508Þ ¼ 1685 var

SUMMARY OF AC POWER IN R, L, AND C

AC power in resistors, inductors, and capacitors, is summarized in Table 10-1. We use the notation Veff and Ieff to include the phase angles. The last column of Table 10-1 is S ¼ VI where S is called apparent power. S is discussed in Section 10.7 in more detail. EXAMPLE 10.6 Find the power delivered from a sinusoidal source to a resistor R. Let the eﬀective values of voltage and current be V and I, respectively. pﬃﬃﬃ pﬃﬃﬃ pR ðtÞ ¼ viR ¼ ðV 2Þ cos !tðI 2Þ cos !t ¼ 2VI cos2 !t ¼ VIð1 þ cos 2!tÞ ¼ RI 2 ð1 þ cos 2!tÞ ¼ Thus,

PR ¼

V2 ð1 þ cos 2!tÞ R

V2 ¼ RI 2 R

Q¼0

224

AC POWER

[CHAP. 10

Table 10-1 pﬃﬃﬃ v ¼ ðVpﬃﬃﬃ2Þ cos !t Veff ¼ V 08 i ¼ ðI 2Þ cos ð!t Þ Ieff ¼ I 8 P ¼ VI cos ; Q ¼ VI sin and S ¼ VI (apparent power)

R

R

L

jL!

i pﬃﬃﬃ V 2 cos !t R pﬃﬃﬃ V 2 cos ð!t 908Þ L!

C

j C!

pﬃﬃﬃ V 2C! cos ð!t þ 908Þ

Z

pðtÞ

Ieff 2

P

Q

2

S 2

V 08 R

V ð1 þ cos 2!tÞ R

V R

0

V R

V 908 L!

V2 sin 2!t L!

0

V2 L!

V2 L!

VC! 908

V 2 C! sin 2!t

0

V 2 C!

V 2 C!

The instantaneous power entering a resistor varies sinusoidally between zero and 2RI 2 , with twice the frequency of excitation, and with an average value of P ¼ RI 2 . vðtÞ and pR ðtÞ are plotted in Fig. 10-5(a). EXAMPLE 10.7 Find the ac power entering an inductor L. pﬃﬃﬃ pﬃﬃﬃ pL ðtÞ ¼ viL ¼ ðV 2Þ cos !tðI 2Þ cos ð!t 908Þ ¼ 2VI cos !t sin !t ¼ VI sin 2!t ¼ L!I 2 sin 2!t ¼

V2 sin 2!t L! P¼0

Thus,

Q ¼ VI ¼

V2 ¼ L!I 2 L!

The instantaneous power entering an inductor varies sinusoidally between Q and Q, with twice the frequency of the source, and an average value of zero. See Fig. 10-5(b). EXAMPLE 10.8 Find the ac power delivered in a capacitor C. pﬃﬃﬃ pﬃﬃﬃ pC ðtÞ ¼ viC ¼ ðV 2Þ cos !t ðI 2Þ cos ð!t þ 908Þ ¼ 2VI cos !t sin !t ¼ VI sin 2!t ¼ C!V 2 sin 2!t ¼ Thus,

I2 sin 2!t C! P¼0

Q ¼ VI ¼

I2 ¼ C!V 2 C!

Like an inductor, the instantaneous power entering a capacitor varies sinusoidally between Q and Q, with twice the frequency of the source, and an average value of zero. See Fig. 10-5(c).

10.6

EXCHANGE OF ENERGY BETWEEN AN INDUCTOR AND A CAPACITOR

If an inductor and a capacitor are fed in parallel by the same ac voltage source or in series by the same current source, the power entering the capacitor is 1808 out of phase with the power entering the inductor. This is explicitly reﬂected in the opposite signs of reactive power Q for the inductor and the capacitor. In such cases, the inductor and the capacitor will exchange some energy with each other, bypassing the ac source. This reduces the reactive power delivered by the source to the LC combination and consequently improves the power factor. See Sections 10.8 and 10.9. EXAMPLE 10.9 pﬃﬃﬃ Find the total instantaneous power pðtÞ, the average power P, and the reactive power Q, delivered from v ¼ ðV 2Þ cos !t to a parallel RLC combination. The total instantaneous power is pT ¼ vi ¼ vðiR þ iL þ iC Þ ¼ pR þ pL þ pC

CHAP. 10]

AC POWER

Fig. 10-5

225

226

AC POWER

[CHAP. 10

Fig. 10-5 (cont.) Substituting the values of pR , pL , and pC found in Examples 10.6, 10.7, and 10.8, respectively, we get V2 1 ð1 þ cos 2!tÞ þ V 2 pT ¼ C! sin 2!t R L! The average power is PT ¼ PR ¼ V 2 =R The reactive power is QT ¼ QL þ QC ¼ V 2 For ð1=L!Þ C! ¼ 0, the total reactive power is zero. factor.

10.7

1 C! L!

ð12Þ

Figure 10-5(d) shows pT ðtÞ for a load with a leading power

COMPLEX POWER, APPARENT POWER, AND POWER TRIANGLE

The two components P and Q of power play diﬀerent roles and may not be added together. However, they may conveniently be brought together in the form of a vector quantity called complex power S pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ and deﬁned by S ¼ P þ jQ. The magnitude jSj ¼ P2 þ Q2 ¼ Veff Ieff is called the apparent power S and is expressed in units of volt-amperes (VA). The three scalar quantities S, P, and Q may be represented geometrically as the hypotenuse, horizontal and vertical legs, respectively, of a right triangle

CHAP. 10]

AC POWER

227

(called a power triangle) as shown in Fig. 10-6(a). The power triangle is simply the triangle of the 2 as shown in Fig. 10-6(b). Power triangles for an inductive load impedance Z scaled by the factor Ieff and a capacitive load are shown in Figs. 10-6(c) and (d), respectively.

Fig. 10-6

Ieff

It can be easily proved that S ¼ Veff Ieff , where Veff is the complex amplitude of eﬀective voltage and is the complex conjugate of the amplitude of eﬀective current. An equivalent formula is S ¼ I2eff Z. In summary, Complex Power:

2 S ¼ Veff Ieff ¼ P þ jQ ¼ Ieff Z

(13)

Real Power:

P ¼ Re½S ¼ Veff Ieff cos

(14)

Reactive Power:

Q ¼ Im½S ¼ Veff Ieff sin

(15)

Apparent Power:

S ¼ Veff Ieff

(16)

EXAMPLE 10.10 (a) A sinusoidal voltage with Veff ¼ 10 V is connected across Z1 ¼ 1 þ j as shown in Fig. 10-7(a). Find i1 , I1;eff , p1 ðtÞ, P1 , Q1 , power factor pf1 , and S1 . (b) Repeat part (a) replacing the load Z1 in (a) by Z2 ¼ 1 j, as shown in Fig. 10-7(b). (c) Repeat part (a) after connecting in parallel Z1 in (a) and Z2 in (b) as shown in Fig.p10-7(c). ﬃﬃﬃ Let v ¼ 10 2 cos !t.

228

AC POWER

(a) See Fig. 10-7(a). pﬃﬃﬃ Z1 ¼ 2 458

(c)

(b)

See Fig. 10-7(b) pﬃﬃﬃ Z2 ¼ 2 458

i1 ¼ 10 cos ð!t 458Þ pﬃﬃﬃ I1;eff ¼ 5 2 458 pﬃﬃﬃ p1 ðtÞ ¼ ð100 2Þ cos !t cos ð!t 458Þ pﬃﬃﬃ ¼ 50 þ ð50 2Þ cos ð2!t 458Þ W

i2 ¼ 10 cos ð!t þ 458Þ pﬃﬃﬃ I2;eff ¼ 5 2 458 pﬃﬃﬃ p2 ðtÞ ¼ ð100 2Þ cos !t cos ð!t þ 458Þ pﬃﬃﬃ ¼ 50 þ ð50 2Þ cos ð2!t þ 458Þ W

P1 ¼ Veff I1;eff cos 458 ¼ 50 W

P2 ¼ Veff I2;eff cos 458 ¼ 50 W

Q1 ¼ Veff I1;eff sin 458 ¼ 50 var

Q2 ¼ Veff I2;eff sin 458 ¼ 50 var

S1 ¼ P1 þ jQ1 ¼ 50 þ j50 pﬃﬃﬃ S1 ¼ jS1 j ¼ 50 2 ¼ 70:7 VA

S2 ¼ P2 þ jQ2 ¼ 50 j50 pﬃﬃﬃ S2 ¼ jS2 j ¼ 50 2 ¼ 70:7 VA

pf1 ¼ 0:707 lagging

pf2 ¼ 0:707 leading

See Fig. 10-7(c).

ð1 þ jÞð1 jÞ ¼1 Z ¼ Z1 kZ2 ¼ ð1 þ jÞ þ ð1 jÞ pﬃﬃﬃ i ¼ 10 2 cos !t Ieff ¼ 10 pðtÞ ¼ 200 cos2 !t ¼ 100 þ 100 cos 2!t W P ¼ Veff Ieff ¼ 100 W Q¼0 S ¼ P ¼ 100 S ¼ jSj ¼ 100 VA pf ¼ 1

Fig. 10-7

[CHAP. 10

CHAP. 10]

AC POWER

Fig. 10-7 (Cont.)

229

230

AC POWER

[CHAP. 10

The results of part (c) may also be derived from the observation that for the Z1 kZ2 combination, i ¼ i1 þ i2 and, consequently, pðtÞ ¼ p1 ðtÞ þ p2 ðtÞ pﬃﬃﬃ pﬃﬃﬃ ¼ ½50 þ ð50 2Þ cos ð2!t 458Þ þ ½50 þ ð50 2Þ cos ð2!t þ 458Þ ¼ 100 þ 100 cos 2!t W P ¼ P1 þ P2 ¼ 50 þ 50 ¼ 100 W Q ¼ Q1 þ Q2 ¼ 50 50 ¼ 0 S ¼ 100 < S1 þ S2 The power triangles are shown in Figs. 10-7(a), (b), and (c). three loads.

Figure 10-7(d) shows the plots of v, i, and p for the

EXAMPLE 10.11 A certain passive network has equivalent impedance Z ¼ 3 þ j4 and an applied voltage v ¼ 42:5 cosð1000t þ 308Þ

ðVÞ

Give complete power information.

Ieff

42:5 Veff ¼ pﬃﬃﬃ 308 V 2 pﬃﬃﬃ V ð42:5= 2Þ 308 8:5 ¼ pﬃﬃﬃ 23:138 A ¼ eff ¼ Z 5 53:138 2

S ¼ Veff Ieff ¼ 180:6 53:138 ¼ 108:4 þ j144:5 Hence, P ¼ 108:4 W, Q ¼ 144:5 var (inductive), S ¼ 180:6 VA, and pf ¼ cos 53:138 ¼ 0:6 lagging.

10.8

PARALLEL-CONNECTED NETWORKS

The complex power S is also useful in analyzing practical networks, for example, the collection of households drawing on the same power lines. Referring to Fig. 10-8, ST ¼ Veff Ieff ¼ Veff ðI1;eff þ I2;eff þ þ In;eff Þ ¼ S1 þ S2 þ þ Sn from which PT ¼ P1 þ P2 þ þ Pn QT ¼ Q1 þ Q2 þ þ Qn qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ST ¼ P2T þ Q2T pf T ¼

PT ST

These results (which also hold for series-connected networks) imply that the power triangle for the network may be obtained by joining the power triangles for the branches vertex to vertex. In the example shown in Fig. 10-9, n ¼ 3, with branches 1 and 3 assumed inductive and branch 2 capacitive. In such diagrams, some of the triangles may degenerate into straight-line segments if the corresponding R or X is zero. If the power data for the individual branches are not important, the network may be replaced by its equivalent admittance, and this used directly to compute ST . EXAMPLE 10.12 Three loads are connected in parallel to a 6-kVeff ac line, as shown in Fig. 10-8. P1 ¼ 10 kW; pf 1 ¼ 1;

P2 ¼ 20 kW; pf2 ¼ 0:5 lagging;

Find PT , QT , ST , pfT , and the current Ieff .

Given

P3 ¼ 15 kW; pf3 ¼ 0:6 lagging

CHAP. 10]

231

AC POWER

Fig. 10-8 We ﬁrst ﬁnd the reactive power for each load: pf1 ¼ cos 1 ¼ 1

tan 1 ¼ 0

Q1 ¼ P1 tan 1 ¼ 0 kvar

pf2 ¼ cos 2 ¼ 0:5

tan 2 ¼ 1:73

Q2 ¼ P2 tan 2 ¼ 34:6 kvar

pf3 ¼ cos 3 ¼ 0:6

tan 3 ¼ 1:33

Q3 ¼ P3 tan 3 ¼ 20 kvar

Then PT , QT , ST , and pfT , are PT ¼ P1 þ P2 þ P3 ¼ 10 þ 20 þ 15 ¼ 45 kW QT ¼ Q1 þ Q2 þ Q3 ¼ 0 þ 34:6 þ 20 ¼ 54:6 kvar qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ST ¼ P2 þ Q2 ¼ 452 þ 54:62 ¼ 70:75 kVA pf T ¼ PT =ST ¼ 0:64 ¼ cos ; ¼ 50:58 lagging Ieff ¼ S=Veff ¼ ð70:75 kVAÞ=ð6 kVÞ ¼ 11:8 A Ieff ¼ 11:8 50:58 A The current could also be found from I ¼ I1 þ I2 þ I3 .

However, this approach is more time-consuming.

Fig. 10-9

10.9

POWER FACTOR IMPROVEMENT

Electrical service to industrial customers is three-phase, as opposed to the single-phase power supplied to residential and small commercial customers. While metering and billing practices vary among the utilities, the large consumers will always ﬁnd it advantageous to reduce the quadrature component of their power triangle; this is called ‘‘improving the power factor.’’ Industrial systems generally have an overall inductive component because of the large number of motors. Each individual load tends to be either pure resistance, with unity power factor, or resistance and inductive reactance, with a lagging power factor. All of the loads are parallel-connected, and the equivalent impedance results in a lagging current and a corresponding inductive quadrature power Q. To improve the power factor, capacitors, in three-phase banks, are connected to the system either on the primary or secondary side of the main transformer, such that the combination of the plant load and the capacitor banks presents a load to the serving utility which is nearer to unit power factor.

232

AC POWER

[CHAP. 10

EXAMPLE 10.13 How much capacitive Q must be provided by the capacitor bank in Fig. 10-10 to improve the power factor to 0.95 lagging?

Fig. 10-10 Before addition of the capacitor bank, pf ¼ cos 258C ¼ 0:906 lagging, and 240 08 ¼ 68:6 258 A 3:5 258 240 68:6 pﬃﬃﬃ þ258 ¼ 8232 258 ¼ 7461 þ j3479 S ¼ Veff Ieff ¼ pﬃﬃﬃ 08 2 2

I1 ¼

After the improvement, the triangle has the same P, but its angle is cos1 0:95 ¼ 18:198. 3479 Qc ¼ tan 18:198 7461

or

Then (see Fig. 10-11),

Qc ¼ 1027 var (capacitive)

The new value of apparent power is S 0 ¼ 7854 VA, as compared to the original S ¼ 8232 VA. The decrease, 378 VA, amounts to 4.6 percent.

Fig. 10-11

The transformers, the distribution systems, and the utility company alternators are all rated in kVA or MVA. Consequently, an improvement in the power factor, with its corresponding reduction in kVA, releases some of this generation and transmission capability so that it can be used to serve other customers. This is the reason behind the rate structures which, in one way or another, make it more costly for an industrial customer to operate with a lower power factor. An economic study comparing the cost of the capacitor bank to the savings realized is frequently made. The results of such a study will show whether the improvement should be made and also what ﬁnal power factor should be attained. EXAMPLE 10.14 A load of P ¼ 1000 kW with pf ¼ 0:5 lagging is fed by a 5-kV source. A capacitor is added in parallel such that the power factor is improved to 0.8. Find the reduction in current drawn from the generator. Before improvement: P ¼ 1000 kW; cos ¼ 0:5; S ¼ P= cos ¼ 2000 kVA; I ¼ 400 A After improvement: P ¼ 1000 kW; cos ¼ 0:8; S ¼ P= cos ¼ 1250 kVA; I ¼ 250 A

CHAP. 10]

233

AC POWER

Hence, for the same amount of real power, the current is reduced by ð400 250Þ=400 ¼ 0:375 or 37.5 percent. EXAMPLE 10.15 A fourth load Q4 is added in parallel to the three parallel loads of Example 10.12 such that the total power factor becomes 0.8 lagging while the total power remains the same. Find Q4 and the resulting S. discuss the eﬀect on the current. In Example 10.12 we found total real and reactive powers to be P ¼ P1 þ P2 þ P3 ¼ 45 kW and Q ¼ Q1 þ Q2 þ Q3 ¼ 54:6 kvar, respectively. For compensation, we now add load Q4 (with P4 ¼ 0Þ such that the new power factor is pf ¼ cos ¼ 0:8 lagging, ¼ 36:878. Then,

tan 36:878 ¼ ðQ þ Q4 Þ=P ¼ ð54:6 þ Q4 Þ=45 ¼ 0:75

Q4 ¼ 20:85 kvar

The results are summarized in Table 10-2. Addition of the compensating load Q4 reduces the reactive power from 54.6 kvar to 33.75 kvar and improves the power factor. This reduces the apparent power S from 70.75 kVA to 56.25 kVA. The current is proportionally reduced. Table 10-2 Load

10.10

P, kW

pf

Q, kvar

S, kVA

#1

10

1

0

10

#2

20

0.5 lagging

34:6

40

#3

15

0.6 lagging

20

25

#ð1 þ 2 þ 3Þ

45

0.64 lagging

54:6

70.75

#4

0

0 leading

20:85

20.85

Total

45

0.8 lagging

33:75

56.25

MAXIMUM POWER TRANSFER

The average power delivered to a load Z1 from a sinusoidal signal generator with open circuit voltage Vg and internal impedance Zg ¼ R þ jX is maximum when Z1 is equal to the complex conjugate of Zg so that Z1 ¼ R jX. The maximum average power delivered to Z1 is Pmax ¼ Vg2 =4R. EXAMPLE 10.16 A generator, with Vg ¼ 100 V(rms) and Zg ¼ 1 þ j, feeds a load Z1 ¼ 2 (Fig. 10-12). (a) Find the average power PZ1 (absorbed by Z1 ), the power Pg (dissipated in Zg ) and PT (provided by the generator). (b) Compute the value of a second load Z2 such that, when in parallel with Z1 , the equivalent impedance is Z ¼ Z1 kZ2 ¼ Zg . (c) Connect in parallel Z2 found in (b) with Z1 and then ﬁnd the powers PZ ; PZ1 ; PZ2 (absorbed by Z, Z1 , and Z2 , respectively), Pg (dissipated in Zg ) and PT (provided by the generator). pﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃ (a) jZ1 þ Zg j ¼ j2 þ 1 þ jj ¼ 10. Thus I ¼ Vg =ðZ1 þ Zg Þ ¼ 100=ð2 þ 1 þ jÞ and jIj ¼ 10 10 A. The required powers are pﬃﬃﬃﬃﬃ PZ1 ¼ Re½Z1 jIj2 ¼ 2ð10 10Þ2 ¼ 2000 W pﬃﬃﬃﬃﬃ Pg ¼ Re½Zg jIj2 ¼ 1ð10 10Þ2 ¼ 1000 W PT ¼ PZ1 þ Pg ¼ 2000 þ 1000 ¼ 3000 W

Fig. 10-12

234

AC POWER

(b) Let Z2 ¼ a þ jb.

To ﬁnd a and b, we set Z1 kZ2 ¼ Zg ¼ 1 j.

[CHAP. 10

Then,

Z1 Z2 2ða þ jbÞ ¼1j ¼ Z1 þ Z2 2 þ a þ jb from which a b 2 ¼ 0 and a þ b þ 2 ¼ 0. Solving these simultaneous equations, a ¼ 0 and b ¼ 2; substituting into the equation above, Z2 ¼ j2: (b) Z ¼ Z1 kZ2 ¼ 1 j and Z þ Zg ¼ 1 j þ 1 þ j ¼ 2. Then, I ¼ Vg =ðZ þ Zg Þ ¼ 100=ð1 j þ 1 þ jÞ ¼ 100=2 ¼ 50 A, and so PZ ¼ Re½Z I2 ¼ 1 502 ¼ 2500 W

Pg ¼ Re½Zg I2 ¼ 1 502 ¼ 2500 W

To p ﬁnd ﬃﬃﬃ PZ1 and PZ2 , we ﬁrst ﬁnd VZ across Z: VZ ¼ IZ ¼ 50ð1 jÞ. Then IZ1 ¼ VZ =Z1 ¼ 50ð1 jÞ=2 ¼ ð25 2Þ 458, and pﬃﬃﬃ PZ2 ¼ 0 W PT ¼ Pg þ PZ1 ¼ 5000 W PZ1 ¼ Re½Z1 jIZ1 j2 ¼ 2ð25 2Þ2 ¼ 2500 W Alternatively, we can state that PZ2 ¼ 0

10.11

and

PZ1 ¼ PZ ¼ 2500 W

SUPERPOSITION OF AVERAGE POWERS

Consider a network containing two AC sources with two diﬀerent frequencies, !1 and !2 . If a common period T may be found for the sources (i.e., !1 ¼ m!, !2 ¼ n!, where ! ¼ 2=T and m 6¼ n), then superposition of individual powers applies (i.e., P ¼ P1 þ P2 ), where P1 and P2 are average powers due to application of each source. The preceding result may be generalized to the case of any n number of sinusoidal sources operating simultaneously on a network. If the n sinusoids form harmonics of a fundamental frequency, then superposition of powers applies. P¼

n X

Pk

k¼1

EXAMPLE 10.17 A practical coil is placed between two voltage sources v1 ¼ 5 cos !1 t and v2 ¼ 10 cos ð!2 t ¼ 608Þ, which share the same common reference terminal (see Fig. 9-54). The coil is modeled by a 5-mH inductor in series with a 10- resistor. Find pﬃﬃﬃthe average power in the coil for (a) !2 ¼ 2!1 ¼ 4000; ðbÞ !1 ¼ !2 ¼ 2000; ðcÞ !1 ¼ 2000 and !2 ¼ 1000 2, all in rad/s. Let v1 by itself produce i1 . Likewise, let v2 produce i2 . Then i ¼ i1 i2 . The instantaneous power p and the average power P are p ¼ Ri2 ¼ Rði1 i2 Þ2 ¼ Ri12 þ Ri22 2Ri1 i2 P ¼ hpi ¼ Rhi12 i þ Rhi22 i 2Rhi1 i2 i ¼ P1 þ P2 2Rhi1 i2 i where hpi indicates the average of p. Note that in addition to P1 and P2 , we need to take into account a third term hi1 i2 i which, depending on !1 and !2 , may or may not be zero. (a) By applying superposition in the phasor domain we ﬁnd the current in the coil (see Example 9.7). I1 ¼

V1 5 ¼ ¼ 0:35 Z1 10 þ j10

458 A; i1 ¼ 0:35 cos ð2000t 458Þ

RI12 10 0:352 ¼ ¼ 0:625 W 2 2 V 10 608 I2 ¼ 2 ¼ ¼ 0:45 3:48 A; i2 ¼ 0:45 cos ð4000t 3:48Þ Z2 10 þ j20

P1 ¼

RI22 10 0:452 ¼ ¼1W 2 2 i ¼ i1 i2 ¼ 0:35 cos ð2000t 458Þ 0:45 cos ð4000t 3:48Þ

P2 ¼

CHAP. 10]

In this case hi1 i2 i ¼ 0 because hcos ð2000t 458Þ cos ð4000t 3:48Þi ¼ 0. applies and P ¼ P1 þ P2 ¼ 0:625 þ 1 ¼ 1:625 W. (b) The current in the coil is i ¼ 0:61 cos ð2000t 1358Þ (see Example 9.7). coil is P ¼ RI 2 =2 ¼ 5 ð0:61Þ2 ¼ 1:875 W. Note that P > P1 þ P2 . (c)

235

AC POWER

Therefore, superposition of power The average power dissipated in the

By applying superposition in the time domain we ﬁnd i1 ¼ 0:35 cos ð2000t 458Þ; P1 ¼ 0:625 W pﬃﬃﬃ i2 ¼ 0:41 cos ð1000 2t 35:38Þ; P2 ¼ 0:833 W

pﬃﬃﬃ i ¼ i1 i2 ; P ¼ hRi2 =2i ¼ P1 þ P2 1:44hcos ð2000t 458Þ cos ð1000 2t 35:38Þi pﬃﬃﬃ The term hcos ð2000t 458Þ cos ð1000 2t 35:38Þi is not determined because a common period can’t be found. The average power depends on the duration of averaging.

Solved Problems 10.1

The current plotted in Fig. 10-2(a) enters a 0.5-mF capacitor in series with a 1-k resistor. Find and plot (a) v across the series RC combination and (b) the instantaneous power p entering RC. (c) Compare the results with Examples 10.1 and 10.2. (a) Referring to Fig. 10-2(a), in one cycle of the current the voltages are 1V ð0 < t < 1 msÞ vR ¼ 1 V ð1 < t < 2 msÞ ðt 2000t ðVÞ ð0 < t < 1 msÞ 1 i dt ¼ vC ¼ C 0 4 2000t ðVÞ ð1 < t < 2 msÞ 1 þ 2000t ðVÞ ð0 < t < 1 msÞ v ¼ vR þ vC ¼ [See Fig. 10-13ðaÞ 3 2000t ðVÞ ð1 < t < 2 msÞ (b) During one cycle, pR ¼ Ri2 ¼ 1 mW 2000t ðmWÞ ð0 < t < 1 msÞ pC ¼ vC i ¼ 2000t 4 ðmWÞ ð1 < t < 2 msÞ 1 þ 2000t ðmWÞ ð0 < t < 1 msÞ p ¼ vi ¼ pR þ pC ¼ 2000t 3 ðmWÞ ð1 < t < 2 msÞ (c)

10.2

The average power entering the circuit during one cycle is equal to the average power absorbed by the resistor. It is the same result obtained in Example 10.1. The power exchanged between the source and the circuit during one cycle also agrees with the result obtained in Example 10.2.

A 1-V ac voltage feeds (a) a 1- resistor, (b) a load Z ¼ 1 þ j, and (c) a load Z ¼ 1 j. Find P in each of the three cases. (a) P ¼ V 2 =R ¼ 1=1 ¼ 1 W pﬃﬃﬃ (b) and (c) jZj ¼ j1 jj ¼ 2.

10.3

[(See Fig. 10-13ðbÞ

pﬃﬃﬃ I ¼ V=jZj ¼ 1= 2.

P ¼ RI 2 ¼ 0:5 W

Obtain the complete power information for a passive circuit with an applied voltage v ¼ 150 cos ð!t þ 108Þ V and a resulting current i ¼ 5:0 cos ð!t 508Þ A. Using the complex power

236

AC POWER

[CHAP. 10

Fig. 10-13

S ¼ Veff Ieff ¼

150 5:0 pﬃﬃﬃ 108 pﬃﬃﬃ 508 ¼ 375 608 ¼ 187:5 þ j342:8 2 2

Thus, P ¼ 187:5 W, Q ¼ 324:8 var (inductive), S ¼ 375 VA, and pf ¼ cos 608 ¼ 0:50 lagging.

10.4

A two-element series circuit has average power 940 W and power factor 0.707 leading. mine the circuit elements if the applied voltage is v ¼ 99:0 cos ð6000t þ 308Þ V. pﬃﬃﬃ The eﬀective applied voltage is 99:0= 2 ¼ 70:0 V.

Substituting in P ¼ Veff Ieff cos ,

940 ¼ ð70:0ÞIeff ð0:707Þ Then, ð19:0Þ2 R ¼ 940, from which R ¼ 2:60 . Z ¼ R jXC

Deter-

or

Ieff ¼ 19:0 A

For a leading pf, ¼ cos1 0:707 ¼ 458, and so

where

XC ¼ R tan 458 ¼ 2:60

Finally, from 2:60 ¼ 1=!C, C ¼ 64:1 mF.

10.5

Find the two elements of a series circuit having current i ¼ 4:24 cos ð5000t þ 458Þ A, power 180 W, and power factor 0.80 lagging. pﬃﬃﬃ The eﬀective value of the current is Ieff ¼ 4:24= 2 ¼ 3:0 A: 180 ¼ ð3:0Þ2 R 1

tor.

The impedance angle is ¼ cos From the power triangle,

or

Then,

R ¼ 20:0

0:80 ¼ þ36:878, wherefore the second element must be an induc-

2 Q Ieff XL ¼ tan 36:878 ¼ 180 P

or

XL ¼ 15:0

CHAP. 10]

237

AC POWER

Finally, from 15.0=5000L, L ¼ 3:0 mH.

10.6

Obtain the power information for each element in Fig. 10-14 and construct the power triangle.

Fig. 10-14 pﬃﬃﬃ The eﬀective current is 14.14/ 2 ¼ 10 A. P ¼ ð10Þ2 3 ¼ 300 W

Qj6 ¼ ð10Þ2 6 ¼ 600 var ðinductiveÞ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ S ¼ ð300Þ2 þ ð600 200Þ2 ¼ 500 VA

Qj2 ¼ ð10Þ2 2 ¼ 200 var ðcapacitiveÞ pf ¼ P=S ¼ 0:6 lagging

The power triangle is shown in Fig. 10-15.

Fig. 10-15

10.7

A series circuit of R ¼ 10 and XC ¼ 5 has an eﬀective applied voltage of 120 V. the complete power information. Z¼

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 102 þ 52 ¼ 11:18

Ieff ¼

Determine

120 ¼ 10:73 A 11:18

Then: 2 R ¼ 1152 W P ¼ Ieff

2 Q ¼ Ieff XC ¼ 576 var (capacitive)

S¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ð1152Þ2 þ ð576Þ2 ¼ 1288 VA

and pf ¼ 1152=1288 ¼ 0:894 leading

10.8

Impedances Zi ¼ 5:83 59:08 and Z2 ¼ 8:94 63:438 are in series and carry an eﬀective current of 5.0 A. Determine the complete power information. ZT ¼ Z1 þ Z2 ¼ 7:0 þ j3:0 Hence,

PT ¼ ð5:0Þ2 ð7:0Þ ¼ 175 W ST ¼

QT ¼ ð5:0Þ2 ð3:0Þ ¼ 75 var (inductive)

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ð175Þ2 þ ð75Þ2 ¼ 190:4 VA

pf ¼

175 ¼ 0:919 lagging 190:4

238

10.9

AC POWER

[CHAP. 10

Obtain the total power information for the parallel circuit shown in Fig. 10-16.

Fig. 10-16 By current division,

Then,

I5 ¼ 17:88 18:438 A I4 ¼ 26:05 12:538 A 2 17:88 26:05 2 PT ¼ pﬃﬃﬃ ð5Þ þ pﬃﬃﬃ ð4Þ ¼ 2156 W 2 2 17:88 2 QT ¼ pﬃﬃﬃ ð3Þ ¼ 480 var (capacitive) 2 qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ST ¼ ð2156Þ2 þ ð480Þ2 ¼ 2209 VA pf ¼

2156 ¼ 0:976 leading 2209

Alternate Method 4ð5 j3Þ ¼ 2:40 j0:53 9 j3 pﬃﬃﬃ pﬃﬃﬃ Then, P ¼ ð42:4= 2Þ2 ð2:40Þ ¼ 2157 W and Q ¼ ð42:4= 2Þ2 ð0:53Þ ¼ 476 var (capacitive). Zeq ¼

10.10 Find the power factor for the circuit shown in Fig. 10-17. With no voltage or current speciﬁed, P, Q, and S cannot be calculated. the cosine of the angle on the equivalent impedance.

However, the power factor is

ð3 þ j4Þð10Þ ¼ 3:68 36:038 13 þ j4 pf ¼ cos 36:038 ¼ 0:809 lagging

Zeq ¼

Fig. 10-17

10.11 If the total power in the circuit Fig. 10-17 is 1100 W, what are the powers in the two resistors? By current division, I1;eff Z2 10 ¼ ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ 2 2 I2;eff Z1 3 þ 42

CHAP. 10]

239

AC POWER

I 2 ð3Þ P3 6 ¼ 21;eff ¼ P10 I2;eff ð10Þ 5

and so

Solving simultaneously with P3 þ P10 ¼ 1100 W gives P3 ¼ 600 W, P10 ¼ 500 W.

10.12 Obtain the power factor of a two-branch parallel circuit where the ﬁrst branch has Z1 ¼ 2 þ j4 , and the second Z2 ¼ 6 þ j0 . To what value must the 6- resistor be changed to result in the overall power factor 0.90 lagging? Since the angle on the equivalent admittance is the negative of the angle on the equivalent impedance, its cosine also gives the power factor. 1 1 þ ¼ 0:334 36:848 S 2 þ j4 6 pf ¼ cosð36:848Þ ¼ 0:80 lagging

Yeq ¼

The pf is lagging because the impedance angle is positive. Now, for a change in power factor to 0.90, the admittance angle must become cos1 0:90 ¼ 25:848. Then, 1 1 1 1 1 0 þ ¼ þ j Yeq ¼ 2 þ j4 R 10 R 5 1=5 ¼ tan 25:848 1 1 þ 10 R

requires

or

R ¼ 3:20

10.13 A voltage, 28.28 608 V, is applied to a two-branch parallel circuit in which Z1 ¼ 4 308 and Z1 ¼ 5 608 . Obtain the power triangles for the branches and combine them into the total power triangle. V V ¼ 7:07 308 A I2 ¼ ¼ 5:66 08 A Z1 Z2 28:28 7:07 pﬃﬃﬃ 308 ¼ 100 308 ¼ 86:6 þ j50:0 S1 ¼ pﬃﬃﬃ 608 2 2 28:28 5:66 pﬃﬃﬃ 08 ¼ 80:0 608 ¼ 40:0 þ j69:3 S2 ¼ pﬃﬃﬃ 608 2 2 ST ¼ S1 þ S2 ¼ 126:6 þ j119:3 ¼ 174:0 43:38 VA I1 ¼

The power triangles and their summation are shown in Fig. 10-18.

Fig. 10-18

240

AC POWER

[CHAP. 10

10.14 Determine the total power information for three parallel-connected loads: load #1, 250 VA, pf ¼ 0:50 lagging; load #2, 180 W, pf ¼ 0:80 leading; load #3, 300 VA, 100 var (inductive). Calculate the average power P and the reactive power Q for each load. Load #1 Given s ¼ 250 VA, cos ¼ 0:50 lagging. Then, qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ P ¼ 250ð0:50Þ ¼ 125 W Q ¼ ð250Þ2 ð125Þ2 ¼ 216:5 var (inductive) Load #2

Given P ¼ 180 W, cos ¼ 0:80 leading. Then, ¼ cos1 0:80 ¼ 36:878 and Q ¼ 180 tanð36:878Þ ¼ 135 var (capacitive)

Load #3

Given S ¼ 300 VA, Q ¼ 100 var (inductive). Then, qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ P ¼ ð300Þ2 ð100Þ2 ¼ 282:8 W

Combining componentwise: PT ¼ 125 þ 180 þ 282:8 ¼ 587:8 W QT ¼ 216:5 135 þ 100 ¼ 181:5 var (inductive) ST ¼ 587:8 þ j181:5 ¼ 615:2 17:168 Therefore, ST ¼ 615:2 VA and pf ¼ cos 17:168 ¼ 0:955 lagging.

10.15 Obtain the complete power triangle and the total current for the parallel circuit shown in Fig. 1019, if for branch 2, S2 ¼ 1490 VA.

Fig. 10-19 2 From S2 ¼ I2;eff Z2 ,

1490 2 I2;eff ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ 222 A2 32 þ 62 and, by current division, I1 3 þ j6 ¼ I2 2 þ j3

whence

2 I1;eff ¼

32 þ 62 2 45 ð222Þ ¼ 768 A2 I2;eff ¼ 13 22 þ 32

2 S1 ¼ I1;eff Z1 ¼ 768ð2 þ j3Þ ¼ 1536 þ j2304

Then,

2 Z2 ¼ 222ð3 þ j6Þ ¼ 666 þ j1332 S2 ¼ I2;eff ST ¼ S1 þ S2 ¼ 2202 þ j3636

that is, PT ¼ 2202 W, QT ¼ 3636 var (inductive), ST ¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ð2202Þ2 þ ð3636Þ2 ¼ 4251 VA

and

pf ¼

2202 ¼ 0:518 lagging 4251

CHAP. 10]

241

AC POWER

Since the phase angle of the voltage is unknown, only the magnitude of IT can be given. By current division, I2 ¼

2 þ j3 I 5 þ j9 T

or

2 I2;eff ¼

22 þ 32 2 13 2 IT;eff ¼ I 106 T;eff 52 þ 92

and so 2 ¼ IT;eff

106 ð222Þ ¼ 1811 A2 13

or

IT;eff ¼ 42:6 A

10.16 Obtain the complete power triangle for the circuit shown in Fig. 10-20, if the total reactive power is 2500 var (inductive). Find the branch powers P1 and P2 .

Fig. 10-20 The equivalent admittance allows the calculation of the total power triangle. Yeq ¼ Y1 þ Y2 ¼ 0:2488 39:578 S Then,

PT ¼ 2500 cot 39:578 ¼ 3025 W ST ¼ 3025 þ j2500 ¼ 3924 39:578 VA

and pf ¼ PT =ST ¼ 0:771 lagging. The current ratio is I1 =I2 ¼ Y1 =Y2 ¼ 0:177=0:0745. P1 I 2 ð4Þ ¼ 21 ¼ 1:88 P2 I2 ð12Þ

and

P1 þ P2 ¼ 3025 W

from which P1 ¼ 1975 W and P2 ¼ 1050 W.

10.17 A load of 300 kW, with power factor 0.65 lagging, has the power factor improved to 0.90 lagging by parallel capacitors. How many kvar must these capacitors furnish, and what is the resulting percent reduction in apparent power? The angles corresponding to the power factors are ﬁrst obtained: cos1 0:65 ¼ 49:468

cos1 0:90 ¼ 25:848

Then (see Fig. 10-21), Q ¼ 300 tan 49:468 ¼ 350:7 kvar (inductive) Q Qc ¼ 300 tan 25:848 ¼ 145:3 kvar (inductive) whence Qc ¼ 205:4 kvar (capacitive). Since S¼

300 ¼ 461:5 kVA 0:65

S0 ¼

300 ¼ 333:3 kVA 0:90

242

AC POWER

[CHAP. 10

Fig. 10-21

the reduction is 461:5 333:3 ð100%Þ ¼ 27:8% 461:5

10.18 Find the capacitance C necessary to improve the power factor to 0.95 lagging in the circuit shown in Fig. 10-22, if the eﬀective voltage of 120 V has a frequency of 60 Hz.

Fig. 10-22 Admittance provides a good approach.

Yeq ¼ j!C þ

1 ¼ 0:0433 jð0:0250 !CÞ 20 308

The admittance diagram, Fig. 10-23, illustrates the next step. ¼ cos1 0:95 ¼ 18:198 0:0250 !C ¼ ð0:0433Þðtan 18:198Þ !C ¼ 0:0108 C ¼ 28:6 mF

Fig. 10-23

ðSÞ

CHAP. 10]

243

AC POWER

10.19 A circuit with impedance Z ¼ 10:0 608 has the power factor improved by a parallel capacitive reactance of 20 . What percent reduction in current results? Since I ¼ VY, the current reduction can be obtained from the ratio of the admittances after and before addition of the capacitors. Ybefore ¼ 0:100 608 S

and

Yafter ¼ 0:050 908 þ 0:100 608 ¼ 0:062 36:208 S Iafter 0:062 ¼ ¼ 0:620 Ibefore 0:100

so the reduction is 38 percent.

10.20 A transformer rated at a maximum of 25 kVA supplies a 12-kW load at power factor 0.60 lagging. What percent of the transformer rating does this load represent? How many kW in additional load may be added at unity power factor before the transformer exceeds its rated kVA? For the 12-kW load, S ¼ 12=060 ¼ 20 kVA. The transformer is at ð20=25Þð100%Þ ¼ 80% of full rating. The additional load at unity power factor does not change the reactive power, qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Q ¼ ð20Þ2 ð12Þ2 ¼ 16 kvar (inductive) Then, at full capacity, 0 ¼ sin1 ð16=25Þ ¼ 39:798 P 0 ¼ 25 cos 39:798 ¼ 19:2 kW Padd ¼ 19:2 12:0 ¼ 7:2 kW Note that the full-rated kVA is shown by an arc in Fig. 10-24, of radius 25.

Fig. 10-24

10.21 Referring to Problem 10.20, if the additional load has power factor 0.866 leading, how many kVA may be added without exceeding the transformer rating? The original load is S ¼ 12 þ j16 kVA and the added load is S2 ¼ S2 308 ¼ S2 ð0:866Þ jS2 ð0:500Þ The total is St ¼ ð12 þ 0:866S2 Þ þ jð16 0:500S2 Þ (kVA).

ðkVAÞ

Then,

ST2 ¼ ð12 þ 0:866S2 Þ2 þ ð16 0:500S2 Þ2 ¼ ð25Þ2 gives S2 ¼ 12:8 kVA.

244

AC POWER

[CHAP. 10

10.22 An induction motor with a shaft power output of 1.56 kW has an eﬃciency of 85 percent. this load, the power factor is 0.80 lagging. Give complete input power information. Pout ¼ 0:85 Pin

or

Pin ¼

At

1:5 ¼ 1:765 kW 0:85

Then, from the power triangle, Sin ¼

1:765 ¼ 2:206 kVA 0:80

Qin ¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ð2:206Þ2 ð1:765Þ2 ¼ 1:324 kvar (inductive)

The equivalent circuit of an induction motor contains a variable resistance which is a function of the shaft load. The power factor is therefore variable, ranging from values near 0.30 at starting to 0.85 at full load.

Supplementary Problems 10.23

Given a circuit with an applied voltage v ¼ 14:14 cos !t (V) and a resulting current i ¼ 17:1 cos ð!t 14:058Þ (mA), determine the complete power triangle. Ans: P ¼ 117 mW; Q ¼ 29:3 mvar (inductive); pf ¼ 0:970 lagging

10.24

Given a circuit with an applied voltage v ¼ 340 sin ð!t 608Þ (V) and a resulting current i ¼ 13:3 sin ð!t 48:78Þ (A), determine the complete power triangle. Ans: P ¼ 2217 W; Q ¼ 443 var (capacitive); pf ¼ 0:981 leading

10.25

A two-element series circuit with R ¼ 5:0 and XL ¼ 15:0 , has an eﬀective voltage 31.6 V across the resistance. Find the complex power and the power factor. Ans: 200 þ j600 Va, 0.316 lagging

10.26

A circuit with impedance Z ¼ 8:0 j6:0 has an applied phasor voltage 70:7 90:08 V. complete power triangle. Ans: P ¼ 200 W; Q ¼ 150 var (capacitive), pf ¼ 0:80 leading

10.27

Determine the circuit impedance which has a complex power S ¼ 5031 26:578 VA for an applied phasor voltage 212:1 08 V. Ans: 4:0 j2:0

10.28

Determine the impedance corresponding to apparent power 3500 VA, power factor 0.76 lagging, and eﬀective current 18.0 A. Ans: 10:8 40:548

10.29

A two-branch parallel circuit, with Z1 ¼ 10 08 and Z2 ¼ 8:0 30:08 , has a total current i ¼ 7:07 cos ð!t 908Þ (A). Obtain the complete power triangle. Ans: P ¼ 110 W; Q ¼ 32:9 var (capacitive), pf ¼ 0:958 leading

10.30

A two-branch parallel circuit has branch impedances Z1 ¼ 2:0 j5:0 and Z2 ¼ 1:0 þ j1:0 . complete power triangle for the circuit if the 2.0- resistor consumes 20 W. Ans: P ¼ 165 W; Q ¼ 95 var (inductive), pf ¼ 0:867 lagging

10.31

A two-branch parallel circuit, with impedances Z1 ¼ 4:0 308 and Z2 ¼ 5:0 608 , has an applied eﬀective voltage of 20 V. Obtain the power triangles for the branches and combine them to obtain the total power triangle. Ans: ST ¼ 128:1 VA, pf ¼ 0:989 lagging

10.32

Obtain the complex power for the complete circuit of Fig. 10-25 if branch 1 takes 8.0 kvar. Ans: S ¼ 8 þ j12 kVA, pf ¼ 0:555 lagging

10.33

In the circuit of Fig. 10-26, ﬁnd Z if ST ¼ 3373 Va, pf ¼ 0:938 leading, and the 3- resistor has an average power of 666 W. Ans: 2 j2

Obtain the

Obtain the

CHAP. 10]

AC POWER

245

Fig. 10-25

Fig. 10-26 10.34

The parallel circuit in Fig. 10-27 has a total average power of 1500 W. information. Ans: S ¼ 1500 þ j2471 VA, pf ¼ 0:519 lagging

Obtain the total power-triangle

Fig. 10-27

10.35

Determine the average power in the 15- and 8- resistances in Fig. 10-28 if the total average power in the circuit is 2000 W. Ans: 723 W, 1277 W

Fig. 10-28

10.36

A three-branch parallel circuit, with Z1 ¼ 25 158 , Z2 ¼ 15 608 , and Z3 ¼ 15 908 , has an applied voltage V ¼ 339:4 308 V. Obtain the total apparent power and the overall power factor. Ans: 4291 VA, 0.966 lagging

10.37

Obtain the complete power triangle for the following parallel-connected loads: load #1, 5 kW, pf ¼ 0:80 lagging; load #2, 4 kVA, 2 kvar (capacitive); load #3, 6 kVA, pf ¼ 0:90 lagging. Ans: 14.535 kVA, pf ¼ 0:954 lagging

246

AC POWER

[CHAP. 10

10.38

Obtain the complete power triangle for the following parallel-connected loads: load #1, 200 VA, pf ¼ 0:70 lagging; load #2, 350 VA, pf ¼ 0:50 lagging; load #3, 275 VA, pf ¼ 1:00. Ans: S ¼ 590 þ j444 VA, pf ¼ 0:799 lagging

10.39

A 4500-VA load at power factor 0.75 lagging is supplied by a 60-Hz source at eﬀective voltage 240 V. Determine the parallel capacitance in microfarads necessary to improve the power factor to (a) 0.90 lagging, (b) 0.90 leading. Ans: ðaÞ 61:8 mF; ðbÞ 212 mF

10.40

In Problem 10.39, what percent reduction in line current and total voltamperes was achieved in part (a)? What further reduction was achieved in part (b)? Ans: 16.1 percent, none

10.41

The addition of a 20-kvar capacitor bank improved the power factor of a certain load to 0.90 lagging. Determine the complex power before the addition of the capacitors, if the ﬁnal apparent power is 185 kVA. Ans: S ¼ 166:5 þ j100:6 kVA

10.42

A 25-kVA load with power factor 0.80 lagging has a group of resistive heating units added at unity power factor. How many kW do these units take, if the new overall power factor is 0.85 lagging? Ans: 4:2 kW

10.43

A 500-kVA transformer is at full load and 0.60 lagging power faactor. A capacitor bank is added, improving the power factor to 0.90 lagging. After improvement, what percent of rated kVA is the transformer carrying? Ans: 66:7 percent

10.44

A 100-kVA transformer is at 80 percent of rated load at power factor 0.85 lagging. How many kVA in additional load at 0.60 lagging power factor will bring the transformer to full rated load? Ans: 21:2 kVA

10.45

A 250-kVA transformer is at full load with power factor 0.80 lagging. ðaÞ How many kvar of capacitors must be added to improve this power factor to 0.90 lagging? (b) After improvement of the power factor, a new load is to be added at 0.50 lagging power factor. How many kVA of this new load will bring the transformer back to rated kVA, and what is the ﬁnal power factor? Ans: ðaÞ 53.1 kvar (capacitive); (b) 33.35 kVA, 0.867 lagging

10.46

A 65-kVA load with a lagging power factor is combined with a 25-kVA synchronous motor load which operates at pf ¼ 0:60 leading. Find the power factor of the 65-kVA load, if the overall power factor is 0.85 lagging. Ans: 0:585 lagging

10.47

An induction motor load of 2000 kVA has power factor 0.80 lagging. Synchronous motors totaling 500 kVA are added and operated at a leading power factor. If the overall power factor is then 0.90 lagging, what is the power factor of the synchronous motors? Ans: 0:92 leading

10.48

Find maximum energy (E) stored in the inductor of Example 10.17(a) and show that it is greater than the sum of maximum stored energies when each source is applied alone ðE1 and E2 Þ. Ans: E ¼ 1:6 mJ, E1 ¼ 306 mJ, E2 ¼ 506 mJ

10.49

The terminal voltage and current of a two-terminal circuit are V rms ¼ 120 V and I rms ¼ 30 608 A at f ¼ 60 Hz. Compute the complex power. Find the impedance of the circuit and its equivalent circuit made of two series elements. Ans: S ¼ 1800 þ j3117:7 VA, Z ¼ 2 þ j3:464 ¼ R þ jL!, R ¼ 2 , L ¼ 9:2 mH

10.50

In the circuit of Fig. 10-29 the voltage source has eﬀective value 10 V at ! ¼ 1 rad/s and the current source is zero. (a) Find the average and reactive powers delivered by the voltage source. (b) Find the eﬀective value of the current in the resistor and the average power absorbed by it and the reactive powers in L and C. Show the balance sheet for the average andpreactive powers between the source and R, L, and C. ﬃﬃﬃ Ans: ðaÞ P ¼ 80 W, Q ¼ 60 var, (b) IR ¼ 5 2 A, PR ¼ 80 W, QC ¼ 160 var, QL ¼ 100 var, PR ¼ P and QL þ QC ¼ Q

CHAP. 10]

10.51

AC POWER

247

pﬃﬃﬃ pﬃﬃﬃ In the circuit of Fig. 10-29, va ¼ 10 2 cos t and ib ¼ 10 2 cos 2t. (a) Find the average power delivered by each source. (b) Find the current in the resistor and the average pﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃ power absorbed by it. Ans: ðaÞ Pa ¼ Pb ¼ 80 W; ðbÞ iR ¼ 2 10 cos ðt 26:58Þ þ 2 10 cos ð2t 63:48Þ, PR ¼ 160 W

Fig. 10-29

10.52

A single-phase AC source having eﬀective value 6 kV delivers 100 kW at a power factor 0.8 lagging to two parallel loads. The individual power factors of the loads are pf1 ¼ 0:7 lagging and pf2 ¼ 0:1 leading. (a) Find powers P1 and P2 delivered to each load. (b) Find the impedance of each load and their combination. Ans: ðaÞ P1 ¼ 97:54 kW, P2 ¼ 2:46 kW, (b) Z1 ¼ 0:244 84:26 , Z2 ¼ 0:043 45:57 , Z ¼ 0:048 36:87

10.53

A practical voltage source is modeled by an ideal voltage source Vg with an open-circuited eﬀective value of 320 V in series with an output impedance Zg ¼ 50 þ j100 . The source feeds a load Z‘ ¼ 200 þ j100 . See Fig. 10-30. ða) Find the average power and reactive power delivered by Vg . (b) Find the average power and reactive power absorbed by the load. (c) A reactive element jX is added in parallel to Z‘ . Find the X such that power delivered to Z‘ is maximized. Ans: ðaÞ Pg ¼ 250 W and Qg ¼ 200 var, (b) P‘ ¼ 200 W and Q‘ ¼ 100 var, (c) X ¼ 100

Fig. 10-30

Polyphase Circuits 11.1

INTRODUCTION The instantaneous power delivered from a sinusoidal source to an impedance is pðtÞ ¼ vðtÞiðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t Þ

ð1Þ

where Vp and Ip are the rms values of v and i, respectively, and is the angle between them. The power oscillates between Vp Ip ð1 þ cos Þ and Vp Ip ð1 þ cos Þ. In power systems, especially at higher levels, it is desirable to have a steady ﬂow of power from source to load. For this reason, polyphase systems are used. Another advantage is having more than one voltage value on the lines. In polyphase systems, Vp and Ip indicate voltage and current, respectively, in a phase which may be diﬀerent from voltages and currents in other phases. This chapter deals mainly with three-phase circuits which are the industry standard. However, examples of two-phase circuits will also be presented.

11.2

TWO-PHASE SYSTEMS

A balanced two-phase generator has two voltage sources producing the same amplitude and frequency but 908 or 1808 out of phase. There are advantages in such a system since it gives the user the option of two voltages and two magnetic ﬁelds. Power ﬂow may be constant or pulsating. EXAMPLE 11.1 An ac generator contains two voltage sources with voltages of the same amplitude and frequency, but 908 out of phase. The references of the sources are connected together to form the generator’s reference terminal n. The system feeds two identical loads [Fig. 11-1(a)]. Find currents, voltages, the instantaneous and average powers delivered. Terminal voltages and currents at generator’s terminal are pﬃﬃﬃ pﬃﬃﬃ vb ðtÞ ¼ Vp 2 cos ð!t 908Þ ð2Þ va ðtÞ ¼ Vp 2 cos !t pﬃﬃﬃ pﬃﬃﬃ ia ðtÞ ¼ Ip 2 cos ð!t Þ ib ðtÞ ¼ Ip 2 cos ð!t 908 Þ In the phasor domain, let Z ¼ jZj and Ip ¼ Vp =jZj.

Then,

VAN ¼ Vp 0

VBN ¼ Vp 908

IA ¼ Ip

IB ¼ Ip 908

pﬃﬃﬃ VAB ¼ VAN VBN ¼ 2Vp 458 pﬃﬃﬃ IN ¼ IA þ IB ¼ Ip 2 458

The voltage and current phasors are shown in Fig. 11-1(b). Instantaneous powers pA ðtÞ and pB ðtÞ delivered by the two sources are

248 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

ð3Þ

CHAP. 11]

POLYPHASE CIRCUITS

249

Fig. 11-1 pa ðtÞ ¼ va ðtÞia ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t Þ pb ðtÞ ¼ vb ðtÞib ðtÞ ¼ Vp Ip cos Vp Ip cos ð2!t Þ The total instantaneous power pT ðtÞ delivered by the generator is pT ðtÞ ¼ pa ðtÞ þ pb ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t Þ þ Vp Ip cos Vp Ip cos ð2!t Þ ¼ 2Vp Ip cos (4) pT ðtÞ ¼ Pavg ¼ 2Vp Ip cos pﬃﬃﬃ In the system of Fig. 11-1(a), two voltage values Vp and 2Vp are available to the load and the power ﬂow is constant. In addition, the 908-phase shift between the two voltages may be used to produce a special rotating magnetic ﬁeld needed in some applications.

Thus,

11.3

THREE-PHASE SYSTEMS

Three-phase generators contain three sinusoidal voltage sources with voltages of the same frequency but a 1208-phase shift with respect to each other. This is realized by positioning three coils at 1208 electrical angle separations on the same rotor. Normally, the amplitudes of the three phases are also equal. The generator is then balanced. In Fig. 11-2, three coils are equally distributed about the circumference of the rotor; that is, the coils are displaced from one another by 120 mechanical degrees.

250

POLYPHASE CIRCUITS

[CHAP. 11

Fig. 11-2

Coil ends and slip rings are not shown; however, it is evident that counterclockwise rotation results in the coil sides A, B, and C passing under the pole pieces in the order . . . A-B-C-A-B-C . . . Voltage polarities reverse for each change of pole. Assuming that the pole shape and corresponding magnetic ﬂux density are such that the induced voltages are sinusoidal, the result for the three coils is as shown in Fig. 11-3. Voltage B is 120 electrical degrees later than A, and C is 2408 later. This is referred to as the ABC sequence. Changing the direction of rotation would result in . . . A-C-B-A-C-B . . . ; which is called the CBA sequence.

Fig. 11-3

The voltages of a balanced ABC sequence in the time and phasor domains are given in (5) and (6), respectively. The phasor diagram for the voltage is shown in Fig. 11-4.

Fig. 11-4

CHAP. 11]

pﬃﬃﬃ van ðtÞ ¼ ðVp 2Þ cos !t

pﬃﬃﬃ vbn ðtÞ ¼ ðVp 2Þ cos ð!t 1208Þ

Van ¼ Vp 0

11.4

251

POLYPHASE CIRCUITS

Vbn ¼ Vp 1208

pﬃﬃﬃ vcn ðtÞ ¼ ðVp 2Þ cos ð!t 2408Þ

Vcn ¼ Vp 2408

ð5Þ ð6Þ

WYE AND DELTA SYSTEMS

The ends of the coils can be connected in wye (also designated Y; see Section 11.8), with ends A 0 , B 0 , and C 0 joined at a common point designated the neutral, N; and with ends A, B, and C brought out to become the lines A, B, and C of the three-phase system. If the neutral point is carried along with the lines, it is a three-phase, four-wire system. In Fig. 11-5, the lines are designated by lowercase a, b, and c at the supply, which could either be a transformer bank or a three-phase alternator, and by uppercase A, B, and C at the load. If line impedances must be considered, then the current direction through, for example, line aA would be IaA , and the phasor line voltage drop VaA .

Fig. 11-5

The generator coil ends can be connected as shown in Fig. 11-6, making a delta-connected (or connected), three-phase system with lines a, b, and c. A delta-connected set of coils has no neutral point to produce a four-wire system, except through the use of -Y transformers.

Fig. 11-6

11.5

PHASOR VOLTAGES

The selection of a phase angle for one voltage in a three-phase system ﬁxes the angles of all other voltages. This is tantamount to ﬁxing the t ¼ 0 point on the horizontal axis of Fig. 11-3, which can be done quite arbitrarily. In this chapter, an angle of zero will always be associated with the phasor voltage of line B with respect to line C: VBC VL 08. pﬃﬃﬃ It is shown in Problem 11.4 that the line-to-line voltage VL is 3 times the line-to-neutral voltage. All ABC-sequence voltages are shown in Fig. 11-7(a) and CBA voltages in Fig. 11-7(b). These phasor

252

POLYPHASE CIRCUITS

[CHAP. 11

Fig. 11-7

voltages, in keeping with the previous chapters, reﬂect maximum values. In the three-phase, four-wire, 480-volt system, widely used for industrial loads, and the 208-volt system, common in commercial buildings, eﬀective values are speciﬁed. In this chapter, pﬃﬃﬃ a line-to-line voltage in the former system would be VBC ¼ 678:8 08 V, making VBC eff ¼ 678:8= 2 ¼ 480 V. People who regularly work in this ﬁeld use eﬀective-valued phasors, and would write VBC ¼ 480 08 V.

11.6

BALANCED DELTA-CONNECTED LOAD

Three identical impedances connected as shown in Fig. 11-8 make up a balanced -connected load. The currents in the impedances are referred to either as phase currents or load currents, and the three will be equal in magnitude and mutually displaced in phase by 1208. The line currents will also be equal in magnitude and displaced from one another by 1208; by convention, they are given a direction from the source to the load. EXAMPLE 11.2 A three-phase, three-wire, ABC system, with an eﬀective line voltage of 120 V, has three impedances of 5:0 458 in a -connection.pﬃﬃﬃDetermine the line currents and draw the voltage-current phasor diagram. The maximum line voltage is 120 2 ¼ 169:7 V. Referring to Fig. 11-7(a), the voltages are: VAB ¼ 169:7 1208 V

VBC ¼ 169:7 08 V

VCA ¼ 169:7 2408 V

Double subscripts give the phase-current directions; for example, IAB passes through the impedance from line A to line B. All current directions are shown in Fig. 11-8. Then the phase currents are IAB ¼

VAB 169:7 1208 ¼ ¼ 33:9 758 Z 5 458

VBC 169:7 08 ¼ 33:9 458 A ¼ Z 5 458 V 169:7 2408 ¼ CA ¼ ¼ 33:9 1958 A Z 5 458

IBC ¼ ICA

A

Fig. 11-8

CHAP. 11]

253

POLYPHASE CIRCUITS

By KCL, line current IA is given by IA ¼ IAB þ IAC ¼ 33:9 758 33:9 1958 ¼ 58:7 458 A Similarly, IB ¼ 58:7 758 A and IC ¼ 58:7 1658 A. The line-to-line voltages and all currents are shown on the phasor diagram, Fig. 11-9. Note particularly the balanced currents. After one phase current has been computed, all other currents pﬃﬃﬃ pﬃﬃﬃmay be obtained through the symmetry of the phasor diagram. Note also that 33:9 3 ¼ 58:7; that is, IL ¼ 3IPh for a balanced delta load.

Fig. 11-9

11.7

BALANCED FOUR-WIRE, WYE-CONNECTED LOAD

Three identical impedances connected as shown in Fig. 11-10 make up a balanced Y-connected load. the currents in the impedances are also the line currents; so the directions are chosen from the source to the load, as before. EXAMPLE 11.3 A three-phase, four-wire, CBA system, with an eﬀective line voltage of 120 V, has three impedances of 20 308 in a Y-connection (Fig. 11-10). Determine the line currents and draw the voltage-current phasor diagram.

Fig. 11-10 pﬃﬃﬃ The maximum line voltage is 169.7 V, and the line-to-neutral magnitude, 169:7= 3 ¼ 98:0 V. 11-7(b), VAN ¼ 98:0 908 V Then

IA ¼

VBN ¼ 98:0 308 V

VCN ¼ 98:0 1508 V

VAN 98:01 908 ¼ ¼ 4:90 608 A Z 20 308

and, similarly, IB ¼ 4:90 608 A, IC ¼ 4:90 1808 A.

From Fig.

254

POLYPHASE CIRCUITS

[CHAP. 11

The voltage-current phasor diagram is shown in Fig. 11-11. Note that with one line current calculated, the other two can be obtained through the symmetry of the phasor diagram. All three line currents return through the neutral. Therefore, the neutral current is the negative sum of the line currents:

Fig. 11-11

Since the neutral current of a balanced, Y-connected, three-phase load is always zero, the neutral conductor may, for computation purposes, be removed, with no change in the results. In actual power circuits, it must not be physically removed, since it carries the (small) unbalance of the currents, carries short-circuit or fault currents for operation of protective devices, and prevents overvoltages on the phases of the load. Since the computation in Example 11.3 proceeded without diﬃculty, the neutral will be included when calculating line currents in balanced loads, even when the system is actually threewire.

11.8

EQUIVALENT Y- AND -CONNECTIONS

Figure 11-12 shows three impedances connected in a (delta) conﬁguration, and three impedances connected in a Y (wye) conﬁguration. Let the terminals of the two connections be identiﬁed in pairs as indicated by the labels , , . Then Z1 is the impedance ‘‘adjoining’’ terminal in the Y-connection, and ZC is the impedance ‘‘opposite’’ terminal in the -connection, and so on. Looking into any two terminals, the two connections will be equivalent if corresponding input, output, and transfer impedances are equal. The criteria for equivalence are as follows:

Fig. 11-12

CHAP. 11]

255

POLYPHASE CIRCUITS

Y-to- Transformation

-to-Y Transformation

Z1 Z2 þ Z1 Z3 þ Z2 Z3 Z3 Z1 Z2 þ Z1 Z3 þ Z2 Z3 ZB ¼ Z2 Z1 Z2 þ Z1 Z3 þ Z2 Z3 ZC ¼ Z1 ZA ¼

ZA ZB ZA þ ZB þ ZC ZA ZC Z2 ¼ ZA þ ZB þ ZC ZB ZC Z3 ¼ ZA þ ZB þ ZC Z1 ¼

It should be noted that if the three impedances of one connection are equal, so are those of the equivalent connection, with Z =ZY ¼ 3.

11.9

SINGLE-LINE EQUIVALENT CIRCUIT FOR BALANCED THREE-PHASE LOADS

Figure 11-13(a) shows a balanced Y-connected load. In many cases, for instance, in power calculations, only the common magnitude, IL , of the three line currents is needed. This may be obtained from the single-line equivalent, Fig. 11-13(b), which represents one phase of the original system, with the line-to-neutral voltage arbitrarily given a zero phase angle. This makes IL ¼ IL , where is the impedance angle. If the actual line currents IA , IB , and IC are desired, their phase angles may be found by adding to the phase angles of VAN , VBN , and VCN as given in Fig. 11-7. Observe that the angle on IL gives the power factor for each phase, pf ¼ cos . The method may be applied to a balanced -connected load if the load is replaced by its Yequivalent, where ZY ¼ 13 Z (Section 11.8).

Fig. 11-13 EXAMPLE 11.4 Rework Example 11.3 by the single-line equivalent method. Referring to Fig. 11-14 (in which the symbol Y indicates the type of connection of the original load), IL ¼

VLN 98:0 08 ¼ ¼ 4:90 308 A Z 20 308

From Fig. 11-7(b), the phase angles of VAN , VBN , and VCN are 908, 308, and 1508. IA ¼ 4:90 608 A

11.10

IB ¼ 4:90 608 A

Hence,

IC ¼ 4:90 1808 A

UNBALANCED DELTA-CONNECTED LOAD

The solution of the unbalanced delta-connected load consists in computing the phase currents and then applying KCL to obtain the line currents. The currents will be unequal and will not have the symmetry of the balanced case. EXAMPLE 11.5

A three-phase, 339.4-V, ABC system [Fig. 11-15(a)] has a -connected load, with ZAB ¼ 10 08

ZBC ¼ 10 308

ZCA ¼ 15 308

256

POLYPHASE CIRCUITS

[CHAP. 11

Fig. 11-14 Obtain phase and line currents and draw the phasor diagram. IAB ¼

VAB 339:4 1208 ¼ ¼ 33:94 1208 A ZAB 10 08

Similarly, IBC ¼ 33:94 308 A and ICA ¼ 22:63 2708 A. Then, IA ¼ IAB þ IAC ¼ 33:94 1208 22:63 2708 ¼ 54:72 108:18 A Also, IB ¼ 65:56 458 A and IC ¼ 29:93 169:18 A. The voltage-current phasor diagram is shown in Fig. 11-15(b), with magnitudes and angles to scale.

Fig. 11-15

11.11 UNBALANCED WYE-CONNECTED LOAD Four-Wire The neutral conductor carries the unbalanced current of a wye-connected load and maintains the line-to-neutral voltage magnitude across each phase of the load. The line currents are unequal and the currents on the phasor diagram have no symmetry. EXAMPLE 11.6 A three-phase, four-wire, 150-V, CBA system has a Y-connected load, with ZA ¼ 6 08

ZB ¼ 6 308

Obtain all line currents and draw the phasor diagram.

ZC ¼ 5 458

See Figure 11-16(a).

VAN 86:6 908 ¼ 14:43 908 A ¼ ZA 6 08 V 86:6 308 ¼ 14:43 08 A IB ¼ BN ¼ ZB 6 308 V 86:6 1508 ¼ 17:32 1058 A IC ¼ CN ¼ ZC 5 458 IA ¼

IN ¼ ð14:43 908 þ 14:43 08 þ 17:32 1058Þ ¼ 10:21 167:08 A Figure 11-16(b) gives the phasor diagram.

CHAP. 11]

POLYPHASE CIRCUITS

257

Fig. 11-16

Three-Wire Without the neutral conductor, the Y-connected impedances will have voltages which vary considerably from the line-to-neutral magnitude. EXAMPLE 11.7 Figure 11-17(a) shows the same system as treated in Example 11.6 except that the neutral wire is no longer present. Obtain the line currents and ﬁnd the displacement neutral voltage, VON .

Fig. 11-17 The circuit is redrawn in Fig. 11-17(b) so as to suggest a single node-voltage equation with VOB as the unknown. VOB VAB VOB VOB þ VBC þ þ ¼0 ZA ZB ZC 1 1 1 150 2408 150 08 VOB þ þ ¼ 6 08 6 308 5 458 6 08 5 458 from which VOB ¼ 66:76 152:858 V.

Then, IB ¼

VOB ¼ 11:13 2:858 A ZB

From VOA þ VAB ¼ VOB , VOA ¼ 100:7 81:088 V, and IA ¼

VOA ¼ 16:78 98:928 A ZA

Similarly, VOC ¼ VOB VCB ¼ 95:58 18:588 V, and IC ¼ 19:12 116:48 A

258

POLYPHASE CIRCUITS

[CHAP. 11

Point O is displaced from the neutral N by a phasor voltage VON , given by 150 VON ¼ VOA þ VAN ¼ 100:7 81:088 þ pﬃﬃﬃ 908 ¼ 20:24 39:538 V 3 The phasor diagram, Fig. 11-18, shows the shift of point O from the centroid of the equilateral triangle. See Problem 11-13 for an alternate method.

Fig. 11-18

11.12

THREE-PHASE POWER

The powers delivered by the three phases of a balanced generator to three identical impedances with phase angle are pa ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t Þ pb ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t 2408 Þ pc ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t 4808 Þ pT ðtÞ ¼ pa ðtÞ þ pb ðtÞ þ pc ðtÞ ¼ 3Vp Ip cos þ Vp Ip ½cos ð2!t Þ þ cos ð2!t 2408 Þ þ cos ð2!t 4808 Þ But cos ð2!t Þ þ cos ð2!t 2408 Þ þ cos ð2!t 4808 Þ ¼ 0 for all t.

Therefore,

pT ðtÞ ¼ 3Vp Ip cos ¼ P The total instantaneous power is the same as the total average power. It may be written in terms of line voltage VL and line current IL . Thus, pﬃﬃﬃ pﬃﬃﬃ In the delta system, VL ¼ Vp and IL ¼ 3Ip . Therefore, P ¼ 3VL IL cos : pﬃﬃﬃ pﬃﬃﬃ In the wye system, VL ¼ 3Vp and IL ¼ Ip . Therefore, P ¼ 3VL IL cos : pﬃﬃﬃ The expression 3VL IL cos gives the power in a three-phase balanced system, regardless of the connection conﬁguration. The power factor of the three-phase system is cos . The line voltage VL in industrial systems is always known. If the load is balanced, the total power can then be computed from the line current and power factor.

CHAP. 11]

POLYPHASE CIRCUITS

259

In summary, power, reactive power, apparent power, and power factor in a three-phase system are pﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃ pﬃﬃﬃ P P ¼ 3V L IL cos Q ¼ 3VL IL sin S ¼ 3VL IL pf ¼ S Of course, all voltage and currents are eﬀective values.

11.13

POWER MEASUREMENT AND THE TWO-WATTMETER METHOD

An ac wattmeter has a potential coil and a current coil and responds to the product of the eﬀective voltage, the eﬀective current, and the cosine of the phase angle between them. Thus, in Fig. 11-19, the wattmeter will indicate the average power supplied to the passive network, P ¼ Veff Ieff cos ¼ Re ðVeff Ieff Þ (see Section 10.7).

Fig. 11-19

Two wattmeters connected in any two lines of a three-phase, three-wire system will correctly indicate the total three-phase power by the sum of the two meter readings. A meter will attempt to go downscale if the phase angle between the voltage and current exceeds 908. In this event, the current-coil connections can be reversed and the upscale meter reading treated as negative in the sum. In Fig. 11-20 the meters are inserted in lines A and C, with the potential-coil reference connections in line B. Their readings will be WA ¼ Re ðVAB eff IA eff Þ ¼ Re ðVAB eff IAB eff Þ þ Re ðVAB eff IAC eff Þ WC ¼ Re ðVCB eff IC eff Þ ¼ Re ðVCB eff ICA eff Þ þ Re ðVCB eff ICB eff Þ in which the KCL expressions IA ¼ IAB þ IAC and IC ¼ ICA þ ICB have been used to replace line currents by phase currents. The ﬁrst term in WA is recognized as PAB , the average power in phase AB of the delta

Fig. 11-20

260

POLYPHASE CIRCUITS

[CHAP. 11

load; likewise, the second term in WC is PCB . Adding the two equations and recombining the middle terms then yields WA þ WC ¼ PAB þ Re ½ðVAB eff VCB eff ÞIAC eff þ PCB ¼ PAB þ PAC þ PCB since, by KVL, VAB VCB ¼ VAC . The same reasoning establishes the analogous result for a Y-connected load. Balanced Loads When three equal impedances Z are connected in delta, the phase currents make 308 angles with their resultant line currents. Figure 11-21 corresponds to Fig. 11-20 under the assumption of ABC sequencing. It is seen that VAB leads IA by þ 308, while VCB leads IC by 308. Consequently, the two wattmeters will read WA ¼ VAB eff IA eff cos ð þ 308Þ

WC ¼ VCB eff IC eff cos ð 308Þ

or, since in general we do not know the relative order in the voltage sequence of the two lines chosen for the wattmeters, W1 ¼ VL eff IL eff cos ð þ 308Þ W2 ¼ VL eff IL eff cos ð 308Þ These expressions also hold for a balanced Y-connection.

Fig. 11-21

Elimination of VL eff IL eff between the two readings leads to pﬃﬃﬃ W2 W1 tan ¼ 3 W2 þ W1 Thus, from the two wattmeter readings, the magnitude of the impedance angle can be inferred. The sign of tan suggested by the preceding formula is meaningless, since the arbitrary subscripts 1 and 2 might just as well be interchanged. However, in the practical case, the balanced load is usually known to be inductive ð > 0Þ.

Solved Problems 11.1

The two-phase balanced ac generator of Fig. 11-22 feeds two identical loads. The two voltage sources are 1808 out of phase. Find (a) the line currents, voltages, and their phase angles, and (b) the instantaneous and average powers delivered by the generator.

CHAP. 11]

261

POLYPHASE CIRCUITS

Fig. 11-22 Let Z ¼ jZj and Ip ¼ Vp =jZj. (a) The voltages and currents in phasor domain are VAN ¼ Vp 0

VBN ¼ Vp 1808 ¼ Vp 0

VAB ¼ VAN VBN ¼ 2Vp 0

Now, from Ip and Z given above, we have IA ¼ Ip

IB ¼ Ip 1808 ¼ Ip

IN ¼ IA þ IB ¼ 0

(b) The instantaneous powers delivered are pa ðtÞ ¼ va ðtÞia ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t Þ pb ðtÞ ¼ vb ðtÞib ðtÞ ¼ Vp Ip cos þ Vp Ip cos ð2!t Þ The total instantaneous power pT ðtÞ is pT ðtÞ ¼ pa ðtÞ þ pb ðtÞ ¼ 2Vp Ip cos þ 2Vp Ip cos ð2!t Þ The average power is Pavg ¼ 2VP Ip cos .

11.2

Solve Problem 11.1 given Vp ¼ 110 Vrms and Z ¼ 4 þ j3 . (a) In phasor form, Z ¼ 4 þ j3 ¼ 5 36:98 . VAN ¼ 110 0 V

Then, VBN ¼ 110 1808 V

VAB ¼ VAN VBN ¼ 110 0 110 1808 ¼ 220 0 and

IA ¼ VAN =Z ¼ 22 36:98 A

V

IB ¼ VBN =Z ¼ 22 216:98 ¼ 22 36:98 A IN ¼ IA þ IB ¼ 0

ðbÞ

pa ðtÞ ¼ 110ð22Þ½cos 36:98 þ cos ð2!t 36:98Þ ¼ 1936 þ 2420 cos ð2!t 36:98Þ

ðWÞ

pb ðtÞ ¼ 110ð22Þ½cos 36:98 þ cos ð2!t 36:98 3608Þ ¼ 1936 þ 2420 cos ð2!t 36:98Þ pðtÞ ¼ pa ðtÞ þ pb ðtÞ ¼ 3872 þ 4840 cos ð2!t 36:98Þ ðWÞ Pavg ¼ 3872 W

ðWÞ

262

POLYPHASE CIRCUITS

11.3

Repeat Problem 11.2 but with the two voltage sources of Problem 11.1 908 out of phase. (a) Again, Z ¼ 5 36:98.

[CHAP. 11

Then, VAN ¼ 110 0 V

VBN ¼ 110 908 V

pﬃﬃﬃ VAB ¼ VAN VBN ¼ 110 0 110 908 ¼ 110ð 2 458 ¼ 155:6 458 V and

IA ¼ VAN =Z ¼ 22 36:98 A

IB ¼ VBN =Z ¼ 22 126:98

A

pﬃﬃﬃ IN ¼ IA þ IB ¼ 22 36:98 þ 22 126:98 ¼ 22ð 2 81:98Þ ¼ 31:1 81:98 A ðbÞ

11.4

pa ðtÞ ¼ 110ð22Þ½cos 36:98 þ cos ð2!t 36:98Þ ¼ 1936 þ 2420 cos ð2!t 36:98Þ ðWÞ pb ðtÞ ¼ 110ð22Þ½cos 36:98 þ cos ð2!t 36:98 1808Þ ¼ 1936 2420 cos ð2!t 36:98Þ pðtÞ ¼ Pa þ Pb ¼ 2ð1936Þ ¼ 3872 W Pavg ¼ 3872 W

Show that the line-to-line voltage VL in a three-phase system is voltage VPh .

ðWÞ

pﬃﬃﬃ 3 times the line-to-neutral

See the voltage phasor diagram (for the ABC sequence), Fig. 11-23.

Fig. 11-23

11.5

A three-phase, ABC system, with an eﬀective voltage 70.7 V, has a balanced -connected load with impedances 20 458 . Obtain the line currents and draw the voltage-current phasor diagram. The circuit is shown in Fig. 11-24. The phasor voltages have magnitudes Vmax ¼ Phase angles are obtained from Fig. 11-7(a). Then, IAB ¼

VAB 100 1208 ¼ ¼ 5:0 758 A Z 20 458

Similarly, IBC ¼ 5:0 458 A and ICA ¼ 5:0 1958 A. The line currents are: IA ¼ IAB þ IAC ¼ 5 758 5 1958 ¼ 8:65 458 A Similarly, IB ¼ 8:65 758 A, IC ¼ 8:65 1658 A. The voltage-current phasor diagram is shown in Fig. 11-25.

pﬃﬃﬃ 2Veff ¼ 100 V.

CHAP. 11]

POLYPHASE CIRCUITS

263

Fig. 11-24

Fig. 11-25

11.6

A three-phase, three-wire CBA system, with an eﬀective line voltage 106.1 V, has a balanced Yconnected load with impedances 5 308 (Fig. 11-26). Obtain the currents and draw the voltage-current phasor diagram. With balanced Y-loads, the neutral conductor carries no current. Even though this system is threewire, the neutralpmay of the line ﬃﬃﬃ be added to simplify computation of the line currents. The magnitude pﬃﬃﬃ voltage is VL ¼ 2ð106:1Þ ¼ 150 V. Then the line-to-neutral magnitude is VLN ¼ 150= 3 ¼ 86:6 V. IA ¼

VAN 86:6 908 ¼ ¼ 17:32 608 A Z 5 308

Fig. 11-26

264

POLYPHASE CIRCUITS

[CHAP. 11

Similarly, IB ¼ 17:32 608 A, IC ¼ 17:32 1808 A. See the phasor diagram, Fig. 11-27, in which the balanced set of line currents leads the set of line-to-neutral voltages by 308, the negative of the angle of the impedances.

Fig. 11-27

11.7

A three-phase, three-wire CBA system, with an eﬀective line voltage 106.1 V, has a balanced connected load with impedances Z ¼ 15 308 . Obtain the line and phase currents by the single-line equivalent method. pﬃﬃﬃ pﬃﬃﬃ Referring to Fig. 11-28, VLN ¼ ð141:4 2Þ= 3 ¼ 115:5 V, and so

IL ¼

115:5 08 ¼ 23:1 308 A ð15=3Þ 308

Fig. 11-28 The line currents lag the ABC-sequence, line-to-neutral voltages by 308: IA ¼ 23:1 608 A

IB ¼ 23:1 608 A

IC ¼ 23:1 1808 A

pﬃﬃﬃ The phase currents, of magnitude IPh ¼ IL = 3 ¼ 13:3 A, lag the corresponding line-to-line voltages by 308: IAB ¼ 13:3 908 A

IBC ¼ 13:3 308 A

ICA ¼ 13:3 2108 A

A sketch of the phasor diagram will make all of the foregoing angles evident.

11.8

A three-phase, three-wire system, with an eﬀective line voltage 176.8 V, supplies two balanced loads, one in delta with Z ¼ 15 08 and the other in wye with ZY ¼ 10 308 . Obtain the total power. First convert the -load to Y, and then use the single-line equivalent circuit, Fig. 11-29, to obtain the line current.

CHAP. 11]

265

POLYPHASE CIRCUITS

Fig. 11-29 144:3 08 144:3 08 þ ¼ 42:0 9:98 A 5 08 10 308 pﬃﬃﬃ pﬃﬃﬃ P ¼ 3VL eff IL eff cos ¼ 3ð176:8Þð29:7Þ cos 9:98 ¼ 8959 IL ¼

Then

11.9

W

Obtain the readings when the two-wattmeter method is applied to the circuit of Problem 11.8. The angle on IL , 9:98, is the negative of the angle on the equivalent impedance of the parallel combination of 5 08 and 10 308 . Therefore, ¼ 9:98 in the formulas of Section 11.13. W1 ¼ VL eff IL eff cos ð þ 308Þ ¼ ð176:8Þð29:7Þ cos 39:98 ¼ 4028 W W2 ¼ VL eff IL eff cos ð 308Þ ¼ ð176:8Þð29:7Þ cos ð20:18Þ ¼ 4931 W As a check, W1 þ W2 ¼ 8959 W, in agreement with Problem 11.8.

11.10 A three-phase supply, with an eﬀective line voltage 240 V, has an unbalanced -connected load shown in Fig. 11-30. Obtain the line currents and the total power.

Fig. 11-30 The power calculations can be performed without knowledge of the sequence of the system. eﬀective values of the phase currents are IAB eff ¼

240 ¼ 9:6 A 25

IBC eff ¼

240 ¼ 16 A 15

ICA eff ¼

240 ¼ 12 A 20

Hence, the complex powers in the three phases are SAB ¼ ð9:6Þ2 ð25 908Þ ¼ 2304 908 ¼ 0 þ j2304 SBC ¼ ð16Þ2 ð15 308Þ ¼ 3840 308 ¼ 3325 þ j1920 SCA ¼ ð12Þ2 ð20 08Þ ¼ 2880 08 ¼ 2880 þ j0

The

266

POLYPHASE CIRCUITS

[CHAP. 11

and the total complex power is their sum, ST ¼ 6205 þ j4224 that is, PT ¼ 6205 W and QT ¼ 4224 var (inductive). To obtain the currents a sequence must be assumed; let it be ABC.

Then, using Fig. 11-7(a),

339:4 1208 ¼ 13:6 308 A 25 908 339:4 08 ¼ 22:6 308 A ¼ 15 308 339:4 2408 ¼ 17:0 2408 A ¼ 20 08

IAB ¼ IBC ICA

The line currents are obtained by applying KCL at the junctions. IA ¼ IAB þ IAC ¼ 13:6 308 17:0 2408 ¼ 29:6 46:78

A

IB ¼ IBC þ IBA ¼ 22:6 308 13:6 308 ¼ 19:7 66:78 A IC ¼ ICA þ ICB ¼ 17:0 2408 22:6 308 ¼ 28:3 173:18 A

11.11 Obtain the readings of wattmeters placed in lines A and B of the circuit of Problem 11.10 (Line C is the potential reference for both meters.) 29:6 WA ¼ Re ðVAC eff IA eff Þ ¼ Re ð240 608Þ pﬃﬃﬃ 46:78 2 ¼ Re ð5023 13:38Þ ¼ 4888 W 19:7 WB ¼ Re ðVBC eff IB eff Þ ¼ Re ð240 08Þ pﬃﬃﬃ 66:78 2 ¼ Re ð3343 66:78Þ ¼ 1322 W Note that WA þ WB ¼ 6210 W, which agrees with PT as found in Problem 11.10.

11.12 A three-phase, four-wire, ABC system, with line voltage VBC ¼ 294:2 08 V, has a Y-connected load of ZA ¼ 10 08 , ZB ¼ 15 308 , and ZC ¼ 10 308 (Fig. 11-31). Obtain the line and neutral currents.

Fig. 11-31

CHAP. 11]

267

POLYPHASE CIRCUITS

169:9 908 ¼ 16:99 908 A 10 08 169:9 308 ¼ 11:33 608 A IB ¼ 15 308 169:9 1508 ¼ 16:99 1208 A IC ¼ 10 308 IN ¼ ðIA þ IB þ IC Þ ¼ 8:04 69:58 A IA ¼

11.13 The Y-connected load impedances ZA ¼ 10 08 , Z ¼ 15 308 , and ZC ¼ 10 308 , in Fig. 11-32, are supplied by a three-phase, three-wire, ABC system in which VBC ¼ 208 08 V. Obtain the voltages across the impedances and the displacement neutral voltage VON .

Fig. 11-32

The method of Example 11.7 could be applied here and one node-voltage equation solved. However, the mesh currents I1 and I2 suggested in Fig. 11-32 provide another approach. I1 10 08 þ 15 308 208 1208 15 308 ¼ 15 308 þ 10 308 I2 15 308 208 08 Solving, I1 ¼ 14:16 86:098 A and I2 ¼ 10:21 52:418 A. IA ¼ I1 ¼ 14:16 86:098 A

The line currents are then

IB ¼ I2 I1 ¼ 8:01 48:938 A

IC ¼ I2 ¼ 10:21 127:598 A

Now the phasor voltages at the load may be computed. VAO ¼ IA ZA ¼ 141:6 86:098 V VBO ¼ IB ZB ¼ 120:2 18:938 V VCO ¼ IC ZC ¼ 102:1 157:598 V VON ¼ VOA þ VAN ¼ 141:6 93:918 þ 120:1 908 ¼ 23:3 114:538 V The phasor diagram is given in Fig. 11-33.

11.14 Obtain the total average power for the unbalanced, Y-connected load in Problem 11.13, and compare with the readings of wattmeters in lines B and C. The phase powers are

268

POLYPHASE CIRCUITS

[CHAP. 11

Fig. 11-33 14:16 pﬃﬃﬃ ð10Þ ¼ 1002:5 W 2 8:01 2 PB ¼ IB eff RB ¼ pﬃﬃﬃ ð15 cos 308Þ ¼ 417:0 W 2 2 10:21 PC ¼ IC2 eff RC ¼ pﬃﬃﬃ ð10 cos 308Þ ¼ 451:4 W 2 PA ¼ IA2 eff RA ¼

and so the total average power is 1870.9 W. From the results of Problem 11.13, the wattmeter readings are: 208 8:01 pﬃﬃﬃ 48:938 ¼ 817:1 W WB ¼ Re ðVBA eff IB eff Þ ¼ Re pﬃﬃﬃ 608 2 2 208 10:21 pﬃﬃﬃ 127:598 ¼ 1052:8 W WC ¼ Re ðVCA eff IC eff ¼ Re pﬃﬃﬃ 24008 2 2 The total power read by the two wattmeters is 1869.9 W.

11.15 A three-phase, three-wire, balanced, -connected load yields wattmeter readings of 1154 W and 557 W. Obtain the load impedance, if the line voltage is 141.4 V. tan ¼ and, using PT ¼

pﬃﬃﬃ W2 W1 pﬃﬃﬃ 577 3 ¼ 0:577 ¼ 3 1731 W2 þ W1

¼ 30:08

pﬃﬃﬃ 3VL eff IL eff cos , pﬃﬃﬃ 3VL eff 3VL2 eff cos 3ð100Þ2 cos 30:08 VLeff ¼ ¼ ¼ ¼ 15:0 Z ¼ IPh eff IL eff PT 1154 þ 577

Thus, Z ¼ 15:0 30:08 .

11.16 A balanced -connected load, with Z ¼ 30 308 , is connected to a three-phase, three-wire, 250-V system by conductors having impedances Zc ¼ 0:4 þ j0:3 . Obtain the line-to-line voltage at the load. The single-line equivalent circuit is shown in Fig. 11-34. By voltage division, the voltage across the substitute Y-load is 10 308 250 pﬃﬃﬃ 08 ¼ 137:4 0:338 V VAN ¼ 0:4 þ j0:3 þ 10 308 3 pﬃﬃﬃ whence VL ¼ ð137:4Þð 3Þ ¼ 238:0 V.

CHAP. 11]

269

POLYPHASE CIRCUITS

Fig. 11-34 Considering the magnitudes only, the line voltage at the load, 238.0 V, represents a drop of 12.0 V. The wire size and total length control the resistance in Zc , while the enclosing conduit material (e.g., steel, aluminum, or ﬁber), as well as the length, aﬀects the inductive reactance.

Supplementary Problems In the following, the voltage-current phasor diagram will not be included in the answer, even though the problem may ask speciﬁcally for one. As a general rule, a phasor diagram should be constructed for every polyphase problem. 11.17

Three impedances of 10:0 53:138 are connected in delta to a three-phase, CBA system with an aﬀective line voltage 240 V. Obtain the line currents. Ans: IA ¼ 58:8 143:138 A; IB ¼ 58:8 23:138 A; IC ¼ 58:8 96:878 A

11.18

Three impedances of 4:20 358 are connected in delta to a three-phase, ABC system having VBC ¼ 495:0 08 V. Obtain the line currents. Ans: IA ¼ 20:41 1258 A; IB ¼ 20:41 58 A; IC ¼ 20:41 1158 A

11.19

A three-phase, three-wire system, with an eﬀective line voltage 100 V, has currents IA ¼ 15:41 1608 A

IB ¼ 15:41 408 A

IC ¼ 15:41 808 A

What is the sequence of the system and what are the impedances, if the connection is delta? Ans: CBA; 15:9 708 11.20

A balanced Y-connected load, with impedances 6:0 458 , is connected to a three-phase, four-wire CBA system having eﬀective line voltage 208 V. Obtain the four line currents. Ans: IA ¼ 28:31 1358 A; IB ¼ 28:31 158 A; IC ¼ 28:31 1058 A; IN ¼ 0

11.21

A balanced Y-connected load, with impedances 65:0 208 , is connected to a three-phase, three-wire, CBA system, where VAB ¼ 678:8 1208 V. Obtain the three line currents. Ans: IA ¼ 6:03 708 A; IB ¼ 6:03 508 A; IC ¼ 6:03 1708 A

11.22

A balanced -connected load, with Z ¼ 9:0 308 , and a balanced Y-connected load, with ZY ¼ 5:0 458 , are supplied by the same three-phase, ABC system, with eﬀective line voltage 480 V. Obtain the line currents, using the single-line equivalent method. Ans: IA ¼ 168:9 93:368 A; IB ¼ 168:9 26:648 A; IC ¼ 168:9 146:648 A

11.23

A balanced -connected load having impedances 27:0 258 and a balanced Y-connected load having impedances 10:0 308 are supplied by the same three-phase, ABC system, with VCN ¼ 169:8 1508 V. Obtain the line currents. Ans: IA ¼ 35:8 117:368 A; IB ¼ 35:8 2:648 A; IC ¼ 35:8 122:648 A

270

POLYPHASE CIRCUITS

[CHAP. 11

11.24

A balanced -connected load, with impedances 10:0 36:98 , and a balanced Y-connected load are supplied by the same three-phase, ABC system having VCA ¼ 141:4 2408 V. If IB ¼ 40:44 13:418 A, what are the impedances of the Y-connected load? Ans: 5:0 53:38

11.25

A three-phase, ABC system, with eﬀective line voltage 500 V, has a -connected load for which ZAB ¼ 10:0 308

ZBC ¼ 25:0 08

ZCA ¼ 20:0 308

Obtain the line currents. Ans: IA ¼ 106:1 90:08 A; IB ¼ 76:15 68:208 A; IC ¼ 45:28 128:658 A 11.26

A three-phase, ABC system, with VBC ¼ 294:2 08 V, has the -connected load ZAB ¼ 5:0 08

ZBC ¼ 4:0 308

ZCA ¼ 6:0 158

Obtain the line currents. Ans: IA ¼ 99:7 99:78 A; IB ¼ 127:9 43:3 A; IC ¼ 77:1 172:18 A 11.27

A three-phase, four-wire, CBA system, with eﬀective line voltage 100 V, has Y-connected impedances ZA ¼ 3:0 08

ZB ¼ 3:61 56:318

ZC ¼ 2:24 26:578

Obtain the currents IA ; IB ; IC ; and IN . Ans: 27:2 908 A; 22:6 26:38 A; 36:4 176:68 A; 38:6 65:38 A 11.28

A three-phase, four-wire, ABC system, with VBC ¼ 294:2 08 V, has Y-connected impedances ZA ¼ 12:0 458

ZB ¼ 10:0 308

ZC ¼ 8:0 08

Obtain the currents IA ; IB ; IC ; and IN . Ans: 14:16 458 A; 16:99 608 A; 21:24 1508 A; 15:32 90:48 A 11.29

A Y-connected load, with ZA ¼ 10 08 , ZB ¼ 10 608 , and ZC ¼ 10 608 , is connected to a threephase, three-wire, ABC system having eﬀective line voltage 141.4 V. Find the load voltages VAO , VBO , VCO and the displacement neutral voltage VON . Construct a phasor diagram similar to Fig. 11-18. Ans: 173:2 908 V; 100 08 V; 100 1808 V; 57:73 908 V

11.30

A Y-connected load, with ZA ¼ 10 608 , ZB ¼ 10 08 , and ZC ¼ 10 608 , is connected to a threephase, three-wire, CBA system having eﬀective line voltage 147.1 V. Obtain the line currents IA , IB , and IC . Ans: 20:8 608 A; 0; 20:8 1208 A

11.31

A three-phase, three-wire, ABC system with a balanced load has eﬀective line voltage 200 V and (maximum) Ans: 2887 W line current IA ¼ 13:61 608 A. Obtain the total power.

11.32

Two balanced -connected loads, with impedances 20 608 and 18 458 , respectively, are connected to a three-phase system for which a line voltage is VBC ¼ 212:1 08 V. Obtain the phase power of each load. After using the single-line equivalent method to obtain the total line current, compute the total power, and compare with the sum of the phase powers. Ans: 562:3 W; 883:6 W; 4337:5 W ¼ 3ð562:3 WÞ þ 3ð883:6 WÞ

11.33

In Problem 11.5, a balanced -connected load with Z ¼ 20 458 resulted in line currents 8.65 A for line voltages 100 V, both maximum values. Find the readings of two wattmeters used to measure the total average power. Ans: 111:9 W; 417:7 W

11.34

Obtain the readings of two wattmeters in a three-phase, three-wire system having eﬀective line voltage 240 V and balanced, -connected load impedances 20 808 . Ans: 1706 W; 3206 W

11.35

A three-phase, three-wire, ABC system, with line voltage VBC ¼ 311:1 08 V, has line currents IA ¼ 61:5 116:68 A

IB ¼ 61:2 48:08 A

IC ¼ 16:1 2188 A

CHAP. 11]

271

POLYPHASE CIRCUITS

Find the readings of wattmeters in lines (a) A and B, (b) B and C, and (c) A and C. Ans: ðaÞ 5266 W, 6370 W; (b) 9312 W, 2322 W; (c) 9549 W, 1973 W 11.36

A three-phase, three-wire, ABC system has an eﬀective line voltage 440 V. IA ¼ 27:9 908 A

IB ¼ 81:0 9:98 A

The line currents are

IC ¼ 81:0 189:98 A

Obtain the readings of wattmeters in lines (a) A and B, (b) B and C. Ans: ðaÞ 7.52 kW, 24.8 kW; (b) 16.16 kW, 16.16 kW 11.37

Two wattmeters in a three-phase, three-wire system with eﬀective line voltage 120 V read 1500 W and 500 W. What is the impedance of the balanced -connected load? Ans: 16:3 40:98

11.38

A three-phase, three-wire, ABC system has eﬀective line voltage 173.2 V. Wattmeters in lines A and B read 301 W and 1327 W, respectively. Find the impedance of the balanced Y-connected load. (Since the sequence is speciﬁed, the sign of the impedance angle can be determined.) Ans: 10 708

11.39

A three-phase, three-wire system, with a line voltage VBC ¼ 339:4 08 V, has a balanced Y-connected load of ZY ¼ 15 608 . The lines between the system and the load have impedances 2:24 26:578 . Find the linevoltage magnitude at the load. Ans: 301.1 V

11.40

Repeat Problem 11.39 with the load impedance ZY ¼ 15 608 . By drawing the voltage phasor diagrams for the two cases, illustrate the eﬀect of load impedance angle on the voltage drop for a given line impedance. Ans: 332.9 V

11.41

A three-phase generator with an eﬀective line voltage of 6000 V supplies the following four balanced loads in parallel: 16 kW at pf ¼ 0:8 lagging, 24 kW at pf ¼ 0:6 lagging, 4 kW at pf ¼ 1, and 1 kW at pf ¼ 0:1 leading. (a) Find the total average power (P) supplied by the generator, reactive power (Q), apparent power (S), power factor, and eﬀective value of line current. (b) Find the amount of reactive load Qc to be added in parallel to produce an overall power factor of 0.9 lagging, then ﬁnd apparent power and eﬀective value of line current. Ans: ðaÞ P ¼ 45 kW, Q ¼ 34:05 kvar, S ¼ 56:43 kVA, pf ¼ 0:8 lagging, IL ¼ 5:43 A, (b) QC ¼ 12:25 kvar, S ¼ 50 kVA, IL ¼ 5:35 A

11.42

A balanced -connected load with impedances Z ¼ 6 þ j9 is connected to a three-phase generator with an eﬀective line voltage of 400 V. The lines between the load and the generator have resistances of 1 each. Find the eﬀective line current, power delivered by the generator, and power absorbed by the load. Ans: IL ¼ 54:43 A, Pg ¼ 26666 W, P‘ ¼ 17777 W

11.43

In Problem 11.42, ﬁnd the eﬀective line voltage at the load. Ans: VL ¼ 340 V

11.44

A three-phase generator feeds two balanced loads (9 kW at pf ¼ 0:8 and 12 kW at pf ¼ 0:6, both lagging) through three cables (0.1 each). The generator is regulated such that the eﬀective line voltage at the load is 220 V. Find the eﬀective line voltage at the generator. Ans: 230 V

11.45

A balanced -connected load has impedances 45 þ j60 . eﬀective line voltage of: (a) 400 V, (b) 390 V. Ans: ðaÞ 3:84 kW, (b) 3.65 kW

11.46

Obtain the change in average power delivered to a three-phase balanced load if the line voltage is multiplied by a factor . Ans: Power is multiplied by the factor 2

11.47

A three-phase, three-wire source supplies a balanced load rated for 15 kW with pf ¼ 0:8 at an eﬀective line voltage of 220 V. Find the power absorbed by the load if the three wires connecting the source to the load have resistances of 0.05 each and the eﬀective line voltage at the source is 220 V. Use both a simpliﬁed

Find the average power delivered to it at an

272

POLYPHASE CIRCUITS

[CHAP. 11

approximation and also an exact method. Ans: 14:67 kW (by an approximate method), 14.54 kW (by an exact method) 11.48

In Problem 11.47 determine the eﬀective value of line voltage such that the load operates at its rated values. Ans: 222.46 V (by an approximate method), 221.98 V (by an exact method)

11.49

What happens to the quantity of power supplied by a three-phase, three-wire system to a balanced load if one phase is disconnected? Ans: Power is halved.

11.50

A three-phase, three-wire generator with eﬀective line voltage 6000 V is connected to a balanced load by three lines with resistances of 1 each, delivering a total of 200 kW. Find the eﬃciency (the ratio of power absorbed by the load to power delivered by the system) if the power factor of the generator is (a) 0.6, (b) 0.9 Ans. (a) 98.5 percent (b) 99.3 percent.

11.51

A 60-Hz three-phase, three-wire system with terminals labeled 1; 2; 3 has an eﬀective line voltage of 220 V. To determine if the system is ABC or CBA, the circuit of Fig. 11-35 is tested. Find the eﬀective voltage between node 4 and line 2 if the system is (a) ABC, (b) CBA. Ans: ðaÞ 80.5 V; (b) 300.5 V

Fig. 11-35

Frequency Response, Filters, and Resonance 12.1

FREQUENCY RESPONSE

The response of linear circuits to a sinusoidal input is also a sinusoid, with the same frequency but possibly a diﬀerent amplitude and phase angle. This response is a function of the frequency. We have already seen that a sinusoid can be represented by a phasor which shows its magnitude and phase. The frequency response is deﬁned as the ratio of the output phasor to the input phasor. It is a real function of j! and is given by Hð j!Þ ¼ Re ½H þ j Im ½H ¼ jHje j

ð1aÞ

where Re [H] and Im [H] are the real and imaginary parts of Hð j!Þ and jHj and are its magnitude and phase angle. Re ½H, Im ½H, |H|, and are, in general, functions of !. They are related by jHj2 ¼ jHð j!Þj2 ¼ Re2 ½H þ Im2 ½H ¼ Hð j!Þ ¼ tan1

Im ½H Re ½H

ð1bÞ ð1cÞ

The frequency response, therefore, depends on the choice of input and output variables. For example, if a current source is connected across the network of Fig. 12-1(a), the terminal current is the input and the terminal voltage may be taken as the output. In this case, the input impedance Z ¼ V1 =I1 constitutes the frequency response. Conversely, if a voltage source is applied to the input and

Fig. 12-1

273 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

274

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

the terminal current is measured, the input admittance Y ¼ I1 =V1 ¼ 1=Z represents the frequency response. For the two-port network of Fig. 12-1(b), the following frequency responses are deﬁned: Input impedance Zin ð j!Þ ¼ V1 =I1 Input admittance Yin ð j!Þ ¼ 1=Zin ð j!Þ ¼ I1 =V1 Voltage transfer ratio Hv ð j!Þ ¼ V2 =V1 Current transfer ratio Hi ð j!Þ ¼ I2 =I1 Transfer impedances V2 =I1 and V1 =I2 EXAMPLE 12.1 Find the frequency response V2 =V1 for the two-port circuit shown in Fig. 12-2. Let YRC be the admittance of the parallel RC combination. Then, YRC ¼ 106 j! þ 1=1250. V2 =V1 is obtained by dividing V1 between ZRC and the 5-k resistor. Hð j!Þ ¼

V2 ZRC 1 1 ¼ ¼ ¼ V1 ZRC þ 5000 1 þ 5000YRC 5ð1 þ 103 j!Þ

ð2aÞ

1 jHj ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ tan1 ð103 !Þ 5 1 þ 106 !2

ð2bÞ

Fig. 12-2

Alternative solution: First we ﬁnd the The´venin equivalent of the resistive part of the circuit, VTh ¼ V1 =5 and RTh ¼ 1 k , and then divide VTh between RTh and the 1-mF capacitor to obtain (2a).

12.2

HIGH-PASS AND LOW-PASS NETWORKS

A resistive voltage divider under a no-load condition is shown in Fig. 12-3, with the standard twoport voltages and currents. The voltage transfer function and input impedance are Hv1 ð!Þ ¼

R2 R1 þ R2

Hz1 ð!Þ ¼ R1 þ R2

The 1 in subscripts indicates no-load conditions. Both Hv1 and Hz1 are real constants, independent of frequency, since no reactive elements are present. If the network contains either an inductance or a capacitance, then Hv1 and Hz1 will be complex and will vary with frequency. If jHv1 j decreases as

Fig. 12-3

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

275

frequency increases, the performance is called high-frequency roll-oﬀ and the circuit is a low-pass network. On the contrary, a high-pass network will have low-frequency roll-oﬀ, with jHv1 j decreasing as the frequency decreases. Four two-element circuits are shown in Fig. 12-4, two high-pass and two lowpass.

Fig. 12-4

The RL high-pass circuit shown in Fig. 12-5 is open-circuited or under no-load. The input impedance frequency response is determined by plotting the magnitude and phase angle of Hz1 ð!Þ ¼ R1 þ j!L2 jHz j H

Fig. 12-5

or, normalizing and writing !x R1 =L2 , Hz1 ð!Þ ¼ 1 þ jð!=!x Þ ¼ R1

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 þ ð!=!x Þ2 tan1 ð!=!x Þ

Five values of ! provide suﬃcient data to plot jHz j=R1 and H , as shown in Fig. 12-6. The magnitude approaches inﬁnity with increasing frequency, and so, at very high frequencies, the network current I1 will be zero. In a similar manner, the frequency response of the output-to-input voltage ratio can be obtained. Voltage division under no-load gives Hv1 ð!Þ ¼ so that

j!L2 1 ¼ R1 þ j!L2 1 jð!x =!Þ

1 jHv j ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 þ ð!x =!Þ2

and

H ¼ tan1 ð!x =!Þ

276

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

!

jHz j=R1

0 0:5!x !x 2!x 1

1 pﬃﬃﬃ 0.5ﬃﬃﬃ 5 p p2 ﬃﬃﬃ 5 1

[CHAP. 12

H 08 26.68 458 63.48 908

Fig. 12-6

The magnitude and angle are plotted in Fig. 12-7. This transfer function approaches unity at high frequency, where the output voltage is the same as the input. Hence the description ‘‘low-frequency rolloﬀ’’ and the name ‘‘high-pass.’’

Fig. 12-7

A transfer impedance of the RL high-pass circuit under no-load is H1 ð!Þ ¼

V2 ¼ j!L2 I1

or

H1 ð!Þ ! ¼j R1 !x

The angle is constant at 908; the graph of magnitude versus ! is a straight line, similar to a reactance plot of !L versus !. See Fig. 12-8.

Fig. 12-8

Interchanging the positions of R and L results in a low-pass network with high-frequency roll-oﬀ (Fig. 12-9). For the open-circuit condition

CHAP. 12]

277

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

Fig. 12-9

Hv1 ð!Þ ¼

R2 1 ¼ R2 þ j!L1 1 þ jð!=!x Þ

with !x R2 =L1 ; that is, 1 jHv j ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 þ ð!=!x Þ2

and

H ¼ tan1 ð!=!x Þ

The magnitude and angle plots are shown in Fig. 12-10. The voltage transfer function Hv1 approaches zero at high frequencies and unity at ! ¼ 0. Hence the name ‘‘low-pass.’’

Fig. 12-10

The other network functions of this low-pass network are obtained in the Solved Problems. EXAMPLE 12.2 Obtain the voltage pﬃﬃﬃ transfer function Hv1 for the open circuit shown in Fig. 12-11. frequency, in hertz, does jHv j ¼ 1= 2 if (a) C2 ¼ 10 nF, (b) C2 ¼ 1 nF?

Fig. 12-11

At what

278

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

Hv1 ð!Þ ¼

1=j!C2 1 ¼ R1 þ ð1=j!C2 Þ 1 þ jð!=!x Þ

where

!x

1 2 104 ¼ R1 C2 C2

[CHAP. 12

ðrad=sÞ

1 jHv j ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 þ ð!=!x Þ2

ðaÞ pﬃﬃﬃ and so jHv j ¼ 1= 2 when

! ¼ !x ¼

2 104 ¼ 2 104 rad=s 10 109

or when f ¼ ð2 104 Þ=2 ¼ 3:18 kHz. f ¼

ðbÞ

10 ð3:18Þ ¼ 31:8 kHz 1

Comparing ðaÞ and ðbÞ, it is seen that the greater the value of C2 , the lower is the frequency at which jHv j drops to 0.707 of its peak value, 1; in other words, the more is the graph of jHv j, shown in Fig. 1210, shifted to the left. Consequently, any stray shunting capacitance, in parallel with C2 , serves to reduce the response of the circuit.

12.3

HALF-POWER FREQUENCIES The frequency !x calculated in Example 12.2, the frequency at which jHv j ¼ 0:707jHv jmax

is called the half-power frequency. In this case, the name is justiﬁed by Problem 12.5, which shows that the power input into the circuit of Fig. 12-11 will be half-maximum when 1 j!C ¼ R1 2 that is, when ! ¼ !x . Quite generally, any nonconstant network function Hð!Þ will attain its greatest absolute value at some unique frequency !x . We shall call a frequency at which jHð!Þj ¼ 0:707jHð!x Þj a half-power frequency (or half-power point), whether or not this frequency actually corresponds to 50 percent power. In most cases, 0 < !x < 1, so that there are two half-power frequencies, one above and one below the peak frequency. These are called the upper and lower half-power frequencies (points), and their separation, the bandwidth, serves as a measure of the sharpness of the peak.

12.4

GENERALIZED TWO-PORT, TWO-ELEMENT NETWORKS

The basic RL or RC network of the type examined in Section 12.2 can be generalized with Z1 and Z2 , as shown in Fig. 12-12; the load impedance ZL is connected at the output port. By voltage division, V2 ¼

Z0 V Z1 þ Z 0 1

or

Hv ¼

V2 Z0 ¼ V1 Z1 þ Z 0

where Z 0 ¼ Z2 ZL =ðZ2 þ ZL Þ, the equivalent impedance of Z2 and ZL in parallel. functions are calculated similarly, and are displayed in Table 12-1.

The other transfer

CHAP. 12]

279

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

Fig. 12-12

Table 12-1 Network Function

Output Condition

V1 I1

ð Þ

Hv ¼

V2 V1

Short-circuit, ZL ¼ 0

Z1

0

Open-circuit ZL ¼ 1

Z1 þ Z2

Z2 Z1 þ Z2

Load, ZL

12.5

Hz ¼

0

Z1 þ Z

0

Z Z1 þ Z 0

Hi ¼

I2 I1

Hv Hz ¼

V2 I1 0

0

Z2 Z

Hi I ¼ 2 H z V1

1

Z2 Z2 þ ZL

ð Þ

0

ðSÞ

1 Z1 0

Z 0 ZL ðZ1 þ Z 0 Þ

THE FREQUENCY RESPONSE AND NETWORK FUNCTIONS

The frequency response of a network may be found by substituting j! for s in its network function. This useful method is illustrated in the following example. EXAMPLE 12.3 Find (a) the network function HðsÞ ¼ V2 =V1 in the circuit shown in Fig. 12-13, (b) Hð j!Þ for LC ¼ 2=!20 and L=C ¼ R2 , and (c) the magnitude and phase angle of Hð j!Þ in (b) for !0 ¼ 1 rad/s. (a) Assume V2 is known. Use generalized impedances Ls and 1=Cs and solve for V1 . From IR ¼ V2 =R, VA ¼ ðR þ LsÞIR ¼ IC ¼ CsVA ¼ Then, and

CsðR þ LsÞ V2 R

and

R þ Ls V2 R

I1 ¼ IR þ IC ¼

ð3Þ

V2 CsðR þ LsÞ 1 þ CsðR þ LsÞ V2 ¼ V2 þ R R R

R þ Ls V2 þ ½1 þ CsðR þ LsÞV2 R V 1 HðsÞ ¼ 2 ¼ V1 2 þ ðL=R þ CRÞs þ LCs2

V1 ¼ VA þ RI1 ¼

Fig. 12-13

(4a)

280

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

pﬃﬃﬃ pﬃﬃﬃ (b) From LC ¼ 2=!20 and L=C ¼ R2 we get L ¼ 2R=!0 and C ¼ 2=R!0 . Substituting L and C into (4a) gives 1 1 1 1 pﬃﬃﬃ p ﬃﬃ ﬃ HðsÞ ¼ or Hð j!Þ ¼ ð4bÞ 2 1 þ 2ðs=!0 Þ þ ðs=!0 Þ2 2 1 þ j 2ð!=!0 Þ ð!=!0 Þ2 jHj2 ¼

1 1 4 1 þ ð!=!0 Þ4

and

¼ tan1

! pﬃﬃﬃ 2!0 ! !20 !2

Note that Hð j!Þ is independent of R. The network passes low-frequency sinusoids and rejects, or attenuates, the high-frequency sinusoids. It is a low-pass ﬁlter with a half-power pﬃﬃﬃ pﬃﬃﬃ frequency of ! ¼ !0 and, in this case, the magnitude of the frequency response is jHð j!0 Þj ¼ jHð0Þj= 2 ¼ 2=4 and its phase angle is Hð j!0 Þ ¼ =2. (c)

For !0 ¼ 1, HðsÞ ¼

1 1 pﬃﬃﬃ 2 1 þ 2s þ s2 1 1 jHj ¼ 4 1 þ !4 2

or

and

Hð j!Þ ¼

1 1 pﬃﬃﬃ 2 1 þ j 2! !2 1

¼ tan

ð4cÞ

pﬃﬃﬃ ! 2! 1 !2

The RC network of Fig 12-4ðbÞ was deﬁned as a ﬁrst-order low-pass ﬁlter with half-power frequency at !0 ¼ 1=R1 C2 . The circuit of Fig. 12-13 is called a second-order Butterworth ﬁlter. It has a sharper cutoﬀ.

12.6

FREQUENCY RESPONSE FROM POLE-ZERO LOCATION

The frequency response of a network is the value of the network function HðsÞ at s ¼ j!. This observation can be used to evaluate Hð j!Þ graphically. The graphical method can produce a quick sketch of Hð j!Þ and bring to our attention its behavior near a pole or a zero without the need for a complete solution. EXAMPLE 12.4 Find poles and zeros of HðsÞ ¼ 10s=ðs2 þ 2s þ 26Þ. Place them in the s-domain and use the polezero plot to sketch Hð j!Þ. HðsÞ has a zero at z1 ¼ 0. Its poles p1 and p2 are found from s2 þ 2s þ 26 ¼ 0 so that p1 ¼ 1 þ j5 and p2 ¼ 1 j5. The pole-zero plot is shown in Fig. 12-14(a). The network function can then be written as HðsÞ ¼ ð10Þ

s z1 ðs p1 Þðs p2 Þ

For each value of s, the term ðs z1 Þ is a vector originating from the zero z1 and ending at point s in the s-domain. Similarly, s p1 and s p2 are vectors drawn from poles p1 and p2 , respectively, to the point s. Therefore, for any value of s, the network function may be expressed in terms of three vectors A, B, and C as follows: HðsÞ ¼ ð10Þ

A BC

where A ¼ ðs z1 Þ; B ¼ ðs p1 Þ, and C ¼ ðs p2 Þ

The magnitude and phase angle of HðsÞ at any point on the s-plane may be found from: jAj jBj jCj HðsÞ ¼ A B C

jHðsÞj ¼ ð10Þ

ð5aÞ ð5bÞ

By placing s on the j! axis [Fig. 12-14(a)], varying ! from 0 to 1, and measuring the magnitudes and phase angles of vectors A, B, and C, we can use (5a) and (5b) to ﬁnd the magnitude and phase angle plots. Figure 12-14(b) shows the magnitude plot.

12.7

IDEAL AND PRACTICAL FILTERS

In general, networks are frequency selective. Filters are a class of networks designed to possess speciﬁc frequency selectivity characteristics. They pass certain frequencies unaﬀected (the pass-band)

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

281

Fig. 12-14

and stop others (the stop-band). Ideally, in the pass-band, Hð j!Þ ¼ 1 and in the stop-band, Hð j!Þ ¼ 0. We therefore recognize the following classes of ﬁlters: low-pass [Fig. 12-15(a)], high-pass [Fig. 12-15(b)], bandpass [Fig. 12-15(c)], and bandstop [Fig. 12-15(d)]. Ideal ﬁlters are not physically realizable, but we can design and build practical ﬁlters as close to the ideal one as desired. The closer to the ideal characteristic, the more complex the circuit of a practical ﬁlter will be. The RC or RL circuits of Section 12.2 are ﬁrst-order ﬁlters. They are far from ideal ﬁlters. As illustrated in the following example, the frequency response can approach that of the ideal ﬁlters if we increase the order of the ﬁlter.

Fig. 12-15

282

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

EXAMPLE 12.5 Three network functions H1 , H2 , and H3 are given by ðaÞ

H1 ¼

1 sþ1

ðbÞ

H2 ¼

s2 þ

1 pﬃﬃﬃ 2s þ 1

Find the magnitudes of their frequency responses. frequency at !0 ¼ 1.

ðcÞ

H3 ¼

1 1 ¼ s3 þ 2s2 þ 2s þ 1 ðs þ 1Þðs2 þ s þ 1Þ

Show that all three functions are low-pass with half-power

1 1 ¼ ð1 þ j!Þð1 j!Þ 1 þ !2 1 1 pﬃﬃﬃ pﬃﬃﬃ ¼ jH2 j2 ¼ ð1 !2 þ j 2!Þð1 !2 j 2!Þ 1 þ !4 1 1 jH3 j2 ¼ ¼ ð1 þ !2 Þð1 !2 þ j!Þð1 !2 j!Þ 1 þ !6

jH1 j2 ¼

ðaÞ ðbÞ ðcÞ

For all three functions, at ! ¼ 0, 1, and 1, we have jHj2 ¼ 1, 1/2, and 0, respectively. Therefore, the three network functions are low-pass with the same half-power frequency of !0 ¼ 1. They are ﬁrst-, second-, and third-order Butterworth ﬁlters, respectively. The higher the order of the ﬁlter, the sharper is the cutoﬀ region in the frequency response.

12.8

PASSIVE AND ACTIVE FILTERS

Filters which contain only resistors, inductors, and capacitors are called passive. Those containing additional dependent sources are called active. Passive ﬁlters do not require external energy sources and they can last longer. Active ﬁlters are generally made of RC circuits and ampliﬁers. The circuit in Fig. 12-16(a) shows a second-order low-pass passive ﬁlter. The circuit in Fig. 12-16(b) shows an active ﬁlter with a frequency response V2 =V1 equivalent to that of the circuit in Fig. 12-16(a). EXAMPLE 12.6 Find the network function V2 =V1 in the circuits shown in (a) Fig. 12-16(a) and (b) Fig. 12-16(b). (a) In Fig. 12-16(a), we ﬁnd V2 from V1 by voltage division. 1 V1 V1 1 V1 ¼ ¼ Cs R þ Ls þ 1=Cs LCs2 þ RCs þ 1 LC s2 þ ðR=LÞs þ ð1=LCÞ pﬃﬃﬃ pﬃﬃﬃ Substituting for R ¼ 1, L ¼ 1= 2, and C ¼ 2, and dividing by V1 , we get V2 ¼

V2 1 ¼ 2 pﬃﬃﬃ V1 s þ 2s þ 1 (b) In Fig. 12-16(b), we apply KCL at nodes A and B with VB ¼ V2 .

Fig. 12-16

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE pﬃﬃﬃ pﬃﬃﬃ ðVA V1 Þ 2 þ ðVA V2 Þ 2 þ ðVA V2 Þ2s ¼ 0

Node A:

ð6aÞ

pﬃﬃﬃ V2 s þ ðV2 VA Þ 2 ¼ 0

Node B:

283

ð6bÞ

By eliminating VA in (6a) and (6b), the network function HðsÞ ¼ V2 =V1 is obtained.

Thus,

V2 1 pﬃﬃﬃ ¼ V1 s2 þ 2s þ 1 Note that the circuits of Figs. 12-16(a) and (b) have identical network functions. worth low-pass ﬁlters with half-power frequencies at ! ¼ 1 rad/s.

12.9

They are second-order Butter-

BANDPASS FILTERS AND RESONANCE The following network function is called a bandpass function. HðsÞ ¼

ks s þ as þ b

where a > 0; b > 0; k > 0

2

ð7Þ

The name is especially appropriate when the poles are complex, close to the j! axis, and away from the origin in the s-domain. The frequency response of the bandpass function is k2 !2 k2 ¼ ð8Þ 2 ðb !2 Þ þ a2 !2 a2 þ ðb !2 Þ2 =!2 pﬃﬃﬃ The maximum of jHj occurs when b !2 ¼ 0 or ! ¼ b, which is called the center frequency !0 . At the center frequency, we have jHjmax ¼ jHð!0 Þj ¼ k=a. The half-power frequencies are at !l and !h , where Hð j!Þ ¼

kj! b !2 þ aj!

jHj2 ¼

jHð!l Þj2 ¼ jHð!h Þj2 ¼ 12 jHð!0 Þj2

ð9aÞ

By applying (8) to (9a), !l and !h are found to be roots of the following equation: ðb !2 Þ2 ¼ a2 !2 pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !l ¼ a2 =4 þ b a=2 qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !h ¼ a2 =4 þ b þ a=2

Solving,

ð9bÞ (9c) ð9dÞ

From (9c) and (9d) we have !h !l ¼ a

and

!h !l ¼ b ¼ !20

ð10aÞ

The bandwidth is deﬁned by ¼ !h !l ¼ a

ð10bÞ

The quality factor Q is deﬁned by Q ¼ !0 = ¼

pﬃﬃﬃ b=a

ð10cÞ

The quality factor measures the sharpness of the frequency response around the center frequency. This behavior is also called resonance (see Sections 12.11 to 12.15). When the quality factor is high, !l and !h may be approximated by !0 =2 and !0 þ =2, respectively. EXAMPLE 12.7 Consider the network function HðsÞ ¼ 10s=ðs2 þ 300s þ 106 Þ. and upper half-power frequencies, the bandwidth, and the quality factor. Since !20 ¼ 106 , the center frequency !0 ¼ 1000 rad/s. The lower and upper half-power frequencies are, respectively,

Find the center frequency, lower

284

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ a2 =4 þ b a=2 ¼ 3002 =4 þ 106 300=2 ¼ 861:2 rad=s qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !h ¼ a2 =4 þ b þ a=2 ¼ 3002 =4 þ 106 þ 300=2 ¼ 1161:2 rad=s !l ¼

The bandwidth ¼ !h !l ¼ 1161:2 861:2 ¼ 300 rad/s. The quality factor Q ¼ 1000=300 ¼ 3:3. EXAMPLE 12.8 Then,

Repeat Example 12.7 for HðsÞ ¼ 10s=ðs2 þ 30s þ 106 Þ. Again, from !20 ¼ 106 , !0 ¼ 1000 rad/s. qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 302 =4 þ 106 30=2 ¼ 985:1 rad=s qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !h ¼ 302 =4 þ 106 þ 30=2 ¼ 1015:1 rad=s !l ¼

¼ a ¼ 30 rad=s

and

Q ¼ 1000=30 ¼ 33:3

Note that !l and !h can also be approximated with good accuracy by !l ¼ !0 =2 ¼ 1000 30=2 ¼ 985 rad=s

12.10

and

!h ¼ !0 þ =2 ¼ 1000 þ 30=2 ¼ 1015 rad=s

NATURAL FREQUENCY AND DAMPING RATIO

The denominator of the bandpass function given in (7) may be written as s2 þ a s þ b ¼ s2 þ 2!0 s þ !20 pﬃﬃﬃ pﬃﬃﬃ where !0 ¼ b is called the natural frequency and ¼ a=ð2 bÞ is called the damping ratio. For > 1, the circuit has two distinct poles on the negative real axis and is called overdamped. For ¼ 1, the circuit has a real pole of orderptwo atﬃ !0 and is critically damped. For < 1, the circuit has a pair of ﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ﬃ conjugate poles at !0 þ j!0 1 2 and !0 j!0 1 2 . The poles are positioned on a semicircle in the left half plane with radius !0 . The placement angle of the poles is ¼ sin1 (see Fig. 12-17). The circuit is underdamped and can contain damped oscillations. Note that the damping ratio is equal to half of the inverse of the quality factor.

Fig. 12-17

12.11

RLC SERIES CIRCUIT; SERIES RESONANCE

The RLC circuit shown in Fig. 12-18 has, under open-circuit condition, an input or driving-point impedance 1 Zin ð!Þ ¼ R þ j !L !C

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

285

Fig. 12-18

The circuit is said to be in series resonance (or low-impedance resonance) when Zin ð!Þ is real (and so jZin ð!Þj is a minimum); that is, when !L

1 ¼0 !C

or

1 ! ¼ !0 pﬃﬃﬃﬃﬃﬃﬃ LC

Figure 12-19 shows the frequency response. The capacitive reactance, inversely proportional to !, is higher at low frequencies, while the inductive reactance, directly proportional to !, is greater at the higher frequencies. Consequently, the net reactance at frequencies below !0 is capacitive, and the angle on Zin is negative. At frequencies above !0 , the circuit appears inductive, and the angle on Zin is positive.

Fig. 12-19

By voltage division, the voltage transfer function for Fig. 12-18 is Hv1 ð!Þ ¼

R ¼ RYin ð!Þ Zin ð!Þ

The frequency response (magnitude only) is plotted in Fig. 12-20; the curve is just the reciprocal of that in Fig. 12-19(a). Note that roll-oﬀ occurs both below and above the series resonant frequency !0 . The points where the response is 0.707, the half-power points (Section 12.3), are at frequencies !l and !h . The bandwidth is the width between these two frequencies: ¼ !h !l . A quality factor, Q0 ¼ !0 L=R, may be deﬁned for the series RLC circuit at resonance. (See Section 12.12 for the general development of Q.) The half-power frequencies can be expressed in terms of the circuit elements, or in terms of !0 and Q0 , as follows: sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ! 2 R R 1 1 1 þ ¼ !0 !h ¼ 1þ þ þ 2L 2L LC 4Q20 2Q0 sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ! 2 R R 1 1 1 þ ¼ !0 1þ !l ¼ þ 2L 2L LC 4Q20 2Q0

286

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

Fig. 12-20

See Problem 12.5.

Subtraction of the expressions gives ¼

R !0 ¼ L Q0

which suggests that the higher the ‘‘quality,’’ the narrower the bandwidth.

12.12

QUALITY FACTOR

A quality factor or ﬁgure of merit can be assigned to a component or to a complete circuit. deﬁned as maximum energy stored Q 2 energy dissipated per cycle

It is

a dimensionless number. This deﬁnition is in agreement with deﬁnitions given in Sections 12.9 and 12.11. A practical inductor, in which both resistance and inductance are present, is modeled in Fig. 12-21. 2 , while the energy dissipated per cycle is The maximum stored energy is 12 LImax 2 I 2 R 2 RÞ ðIeff ¼ max ! !

Fig. 12-21

Hence,

Qind ¼

!L R

A practical capacitor can be modeled by a parallel combination of R and C, as shown in Fig. 12.22. 2 2 The maximum stored energy is 12 CVmax and the energy dissipated per cycle is Vmax =R!. Thus, Qcap ¼ !CR. The Q of the series RLC circuit is derived in Problem 12.6(a). It is usually applied at resonance, in which case it has the equivalent forms ! L 1 1 Q0 ¼ 0 ¼ ¼ R !0 CR R

rﬃﬃﬃﬃ L C

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

287

Fig. 12-22

12.13

RLC PARALLEL CIRCUIT; PARALLEL RESONANCE

A parallel RLC network is shown in Fig. 12-23. condition, the input admittance is Yin ð!Þ ¼

Observe that V2 ¼ V1 .

Under the open-circuit

1 1 1 þ þ j!C ¼ R j!L Zin ð!Þ

Fig. 12-23

The network will be in parallel resonance (or high-impedance resonance) when Yin ð!Þ, and thus Zin ð!Þ, is real (and so jYin ð!Þj is a minimum and jZin ð!Þj is a maximum); that is, when 1 ! ¼ !a pﬃﬃﬃﬃﬃﬃﬃ LC pﬃﬃﬃﬃﬃﬃﬃ The symbol !a is now used to denote the quantity 1= LC in order to distinguish the resonance from a low-impedance resonance. Complex series-parallel networks may have several high-impedance resonant frequencies !a and several low-impedance resonant frequencies !0 . The normalized input impedance

1 þ !C ¼ 0 !L

Zin ð!Þ ¼ R

or

1 1 1 þ jR !C !L

is plotted (magnitude only) in Fig. 12-24. Half-power frequencies !l and !h are indicated on the plot. Analogous to series resonance, the bandwidth is given by ¼

!a Qa

where Qa , the quality factor of the parallel circuit at ! ¼ !a , has the equivalent expressions rﬃﬃﬃﬃ R C ¼ !a RC ¼ R Qa ¼ !a L L See Problem 12.6(b).

288

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

Fig. 12-24

12.14

PRACTICAL LC PARALLEL CIRCUIT

A parallel LC ‘‘tank’’ circuit has frequency applications in electronics as a tuning or frequency selection device. While the capacitor may often be treated as ‘‘pure C,’’ the losses in the inductor should be included. A reasonable model for the practical tank is shown in Fig. 12-25. The input admittance is 1 R !L ¼ 2 þ j !C Yin ð!Þ ¼ j!C þ R þ j!L R þ ð!LÞ2 R2 þ ð!LÞ2

Fig. 12-25

For resonance, ! L !a C ¼ 2 a R þ ð!a LÞ2

or

1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃ LC

rﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ R2 C 1 L

At the resonant frequency, Yin ð!a Þ ¼ RC=L and, from Section 12.11, the Q of the inductance at !a is Qind

! L ¼ a ¼ R

rﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ L 1 CR2

pﬃﬃﬃﬃﬃﬃﬃ If Qind 10, then !a 1= LC and Zin ð!a Þ 2 R Qind The frequency response is similar to that of the parallel RLC circuit, except that the high-impedance resonance occurs at a lower frequency for low Qind . This becomes evident when the expression for !a above is rewritten as 1 1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ LC 1 þ ð1=Q2ind Þ

CHAP. 12]

12.15

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

289

SERIES-PARALLEL CONVERSIONS

It is often convenient in the analysis of circuits to convert the series RL to the parallel form (see Fig. 12-26). Given Rs , Ls , and the operating frequency !, the elements Rp , Lp of the equivalent parallel circuit are determined by equating the admittances Ys ¼

Rs j!Ls R2s þ ð!Ls Þ2

and

Yp ¼

1 1 þ Rp j!Lp

Fig. 12-26

The results are "

# !Ls 2 Rp ¼ Rs 1 þ ¼ Rs ð1 þ Q2s Þ Rs " # Rs 2 1 Lp ¼ Ls 1 þ ¼ Ls 1 þ 2 !Ls Qs

If Qs 10, Rp Rs Q2s and Lp Ls . There are times when the RC circuit in either form should be converted to the other form (see Fig. 12-27). Equating either the impedances or the admittances, one ﬁnds

Fig. 12-27

Rs ¼

Rp 2

¼

Rp 1 þ Q2p #

1 þ ð!Cp Rp Þ " ! 1 1 Cs ¼ Cp 1 þ ¼ Cp 1 þ 2 Qp ð!Cp Rp Þ2

as the parallel-to-series transformation, and Rp ¼ Rs 1 þ

1 ¼ Rs ð1 þ Q2s Þ ð!Cs Rs Þ2 Cs Cs Cp ¼ ¼ 1 þ ð!Cs Rs Þ2 1 þ ð1=Qs Þ2

as the series-to-parallel transformation.

Again, the equivalence depends on the operating frequency.

290

12.16

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

LOCUS DIAGRAMS

Heretofore, the frequency response of a network has been exhibited by plotting separately the magnitude and the angle of a suitable network function against frequency !. This same information can be presented in a single plot: one ﬁnds the curve (locus diagram) in the complex plane traced by the point representing the network function as ! varies from 0 to 1. In this section we shall discuss locus diagrams for the input impedance or the input admittance; in some cases the variable will not be !, but another parameter (such as resistance R). For the series RL circuit, Fig. 12-28(a) shows the Z-locus when !L is ﬁxed and R is variable; Fig. 1228(b) shows the Z-locus when R is ﬁxed and L or ! is variable; and Fig. 12-28(c) shows the Y-locus when R is ﬁxed and L or ! is variable. This last locus is obtained from Y¼

1 1 ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ tan1 ð!L=RÞ R þ j!L R2 þ ð!LÞ2

Fig. 12-28

Note that for !L ¼ 0, Y ¼ ð1=RÞ 08; and for !L ! 1, Y ! 0 908. When !L ¼ R, 1 Y ¼ pﬃﬃﬃ 458 R 2 A few other points will conﬁrm the semicircular locus, with the center at 1/2R and the radius 1/2R. Either Fig. 12-28(b) or 12-28(c) gives the frequency response of the circuit. A parallel RC circuit has the Y- and Z-loci shown in Fig. 12-29; these are derived from Y¼

1 þ j!C R

and

R Z ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ tan1 ð!CRÞ 1 þ ð!CRÞ2

Fig. 12-29

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

291

For the RLC series circuit, the Y-locus, with ! as the variable, may be determined by writing Y ¼ G þ jB ¼ whence

G¼

R R2 þ X 2

1 R jX ¼ R þ jX R2 þ X 2 X B¼ 2 R þ X2

Both G and B depend on ! via X. Eliminating X between the two expressions yields the equation of the locus in the form 2 G 1 2 2 1 G2 þ B2 ¼ or G þB ¼ R 2R 2R which is the circle shown in Fig. 12-30. and ! ¼ !h .

Note the points on the locus corresponding to ! ¼ !l , ! ¼ !0 ,

Fig. 12-30

For the practical ‘‘tank’’ circuit examined in Section 12.14, the Y-locus may be constructed by combining the C-branch locus and the RL-branch locus. To illustrate the addition, the points corresponding to frequencies !1 < !2 < !3 are marked on the individual loci and on the sum, shown in Fig. 12-31(c). It is seen that jYjmin occurs at a frequency greater than !a ; that is, the resonance is highimpedance but not maximum-impedance. This comes about because G varies with ! (see Section 12.14), and varies in such a way that forcing B ¼ 0 does not automatically minimize G2 þ B2 . The separation of

Fig. 12-31

292

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

the resonance and minimum-admittance frequencies is governed by the Q of the coil. Higher Qind corresponds to lower values of R. It is seen from Fig. 12-31(b) that low R results in a larger semicircle, which when combined with the YC -locus, gives a higher !a and a lower minimum-admittance frequency. When Qind 10, the two frequencies may be taken as coincident. The case of the two-branch RC and RL circuit shown in Fig. 12-32(a) can be examined by adding the admittance loci of the two branches. For ﬁxed V ¼ V 08, this amounts to adding the loci of the two branch currents. Consider C variable without limit, and R1 , R2 , L, and ! constant. Then current IL is ﬁxed as shown in Fig. 12-32(b). The semicircular locus of IC is added to IL to result in the locus of IT . Resonance of the circuit corresponds to T ¼ 0. This may occur for two values of the real, positive parameter C [the case illustrated in Fig. 12.32(b)], for one value, or for no value—depending on the number of real positive roots of the equation Im YT ðCÞ ¼ 0.

Fig. 12-32

12.17

SCALING THE FREQUENCY RESPONSE OF FILTERS

The frequency scale of a ﬁlter may be changed by adjusting the values of its inductors and capacitors. Here we summarize the method (see also Section 8.10). Inductors and capacitors aﬀect the frequency behavior of circuits through L! and C!; that is, always as a product of element values and the frequency. Dividing inductor and capacitor values in a circuit by a factor k will scale-up the !-axis of the frequency response by a factor k. For example, a 1-mH inductor operating at 1 kHz has the same impedance as a 1-mH inductor operating at 1 MHz. Similarly, a 1-mF capacitor at 1 MHz behaves similar to a 1-nF capacitor at 1 GHz. This is called frequency scaling and is a useful property of linear circuits. The following two examples illustrate its application in ﬁlter design. EXAMPLE 12.17 The network function of the circuit of Fig. 8-42 with R ¼ 2 k , C ¼ 10 nF, and R2 ¼ R1 is HðsÞ ¼

V2 2 ¼ 2 V1 s s þ þ1 !0 !0

where !0 ¼ 50, 000 rad/s (see Examples 8.14 and 8.15). This is a low-pass ﬁlter with the cutoﬀ frequency at !0 . By using a 1-nF capacitor, !0 ¼ 500,000 and the frequency response is scaled up by a factor of 10. EXAMPLE 12.18 A voltage source is connected to the terminals of a series RLC circuit. The phasor current is I ¼ Y V, where YðsÞ ¼

Cs LCs2 þ RCs þ 1

pﬃﬃﬃﬃﬃﬃﬃ This is a bandpass function with a peak of the resonance pﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃ frequency of !0 ¼ 1= LC . Changing L and C to L=k and C=k (a reduction factor of k) changes 1= LC to k= LC and the new resonance frequency is increased to k!0 . You may verify the shift in frequency at which the current reaches its maximum by direct evaluation of Yð j!Þ for the following two cases: (a) L ¼ 1 mH, C ¼ 10 nF, !0 ¼ 106 rad/s; (b) L ¼ 10 mH, C ¼ 100 nF, !0 ¼ 105 rad/s.

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

293

Solved Problems 12.1

In the two-port network shown in Fig. 12-33, R1 ¼ 7 k and R2 ¼ 3 k . ratio V2 =V1 (a) at no-load, (b) for RL ¼ 20 k .

Obtain the voltage

Fig. 12-33

(a) At no-load, voltage division gives V2 R2 3 ¼ 0:30 ¼ ¼ V1 R1 þ R2 7 þ 3 (b) With RL ¼ 20 k , Rp ¼

and

R2 RL 60 ¼ R2 þ RL 23

k

Rp V2 60 ¼ 0:27 ¼ ¼ V1 R1 þ Rp 221

The voltage ratio is independent of frequency. The load resistance, 20 k , reduced the ratio from 0.30 to 0.27.

12.2

(a) Find L2 in the high-pass circuit shown in Fig. 12-34, if jHv ð!Þj ¼ 0:50 at a frequency of 50 MHz. (b) At what frequency is jHv j ¼ 0:90? (a) From Section 12.2, with !x R1 =L2 , 1 jHv ð!Þj ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 þ ð!x =!Þ2 Then,

1 0:50 ¼ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 þ ð fx =50Þ2

Fig. 12-34

or

pﬃﬃﬃ fx ¼ 50 3 MHz

294

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

and

L2 ¼

12.3

R1 50 103 pﬃﬃﬃ ¼ ¼ 91:9 mH 2fx 2ð50 3 106 Þ

1 pﬃﬃﬃ 1 þ ð50 3=f Þ2

0:90 ¼

ðbÞ

[CHAP. 12

or

f ¼ 179 MHz

A voltage divider, useful for high-frequency applications, can be made with two capacitors C1 and C2 in the generalized two-port network Fig. 12-2. Under open-circuit, ﬁnd C2 if C1 ¼ 0:01 mF and jHv j ¼ 0:20. From Table 12-1, Hv ¼

Hence,

Z2 ¼ Z1 þ Z2

0:20 ¼

1=j!C2 C1 ¼ 1 1 C1 þ C2 þ j!C1 j!C2

0:01 0:01 þ C2

or

C2 ¼ 0:04 mF

The voltage ratio is seen to be frequency-independent under open-circuit.

12.4

Find the frequency at which jHv j ¼ 0:50 for the low-pass RC network shown in Fig. 12-35. Hv ð!Þ ¼

1 1 þ jð!=!x Þ

where

!x

1 R1 C2

Fig. 12-35

Then, and

12.5

1 from which 1 þ ð!=!x Þ2 pﬃﬃﬃ 1 !¼ 3 ¼ 8660 rad=s or R1 C2

pﬃﬃﬃ ! ¼ 3 !x

ð0:50Þ2 ¼

f ¼ 1378 Hz

For the series RLC circuit shown in Fig. 12-36, ﬁnd the resonant frequency !0 ¼ 2f0 . obtain the half-power frequencies and the bandwidth . 1 Zin ð!Þ ¼ R þ j !L !C pﬃﬃﬃﬃﬃﬃﬃ At resonance, Zin ð!Þ ¼ R and !0 ¼ 1= LC . 1 !0 ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ 2236:1 rad=s 0:5ð0:4 106 Þ The power formula

f0 ¼

!0 ¼ 355:9 Hz 2

Also

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

295

Fig. 12-36 2 P ¼ Ieff R¼

2 Veff R jZin j2

2 shows that Pmax ¼ Veff =R, achieved at ! ¼ !0 , and that P ¼ 12 Pmax when jZin j2 ¼ 2R2 ; that is, when

!L

1 ¼ R !C

or

!2

R 1 ! ¼0 L LC

Corresponding to the upper sign, there is a single real positive root: sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ﬃ 2 R R 1 þ ¼ 2338:3 rad=s or þ !h ¼ 2L 2L LC

fh ¼ 372:1 Hz

and corresponding to the lower sign, the single real positive root sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 R R 1 þ ¼ 2138:3 rad=s or þ !l ¼ 2L 2L LC

12.6

fl ¼ 340:3 Hz

Derive the Q of (a) the series RLC circuit, (b) the parallel RLC circuit. (a) In the time domain, the instantaneous stored energy in the circuit is given by 1 q2 Ws ¼ Li2 þ 2 2C For a maximum, dWs di q dq di q ¼i L þ ¼ iðvL þ vC Þ ¼ 0 ¼ Li þ dt C dt dt C dt Thus, the maximum stored energy is Ws at i ¼ 0 or Ws at vL þ vC ¼ 0, whichever is the larger. Now the capacitor voltage, and therefore the charge, lags the current by 908; hence, i ¼ 0 implies q ¼ Qmax and 2 Q2 1 1 I I2 Ws ji¼0 ¼ max ¼ CVC2 max ¼ C max ¼ max2 2 2 2C !C 2C! On the other hand, vL þ vC ¼ 0 implies vL ¼ vC ¼ 0 and i ¼ Imax (see the phasor diagram, Fig. 1237), so that 2 Ws jvL þvC ¼0 ¼ 12 LImax

It follows that Ws max ¼

8 2 < Imax =2C!2

ð! !0 Þ

:

ð! !0 Þ

2 LImax =2

2 R=!. The energy dissipated per cycle (in the resistor) is Wd ¼ Imax W 1=!CR ð! !0 Þ Q ¼ 2 s max ¼ !L=R ð! !0 Þ Wd

Consequently,

296

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

Fig. 12-37 (b) For the parallel combination with applied voltage vðtÞ, 1 1 2 q Ws ¼ LIL2 þ 2 2C C dWs di q ¼ LiL L þ C iC ¼ vðiL þ iC Þ ¼ 0 dt dt C

and If v ¼ 0, then qC ¼ 0 and

iL ¼ IL max ¼

giving

Wsjv¼0 ¼

Vmax !L

2 Vmax 2L!2

If iL þ iC ¼ 0, then (see Fig. 12-38) iL ¼ iC ¼ 0 and qC ¼ CVmax , giving 2 Ws jiL þiC ¼0 ¼ 12 CVmax

Fig. 12-38 ( Therefore

Ws max ¼

2 =2L!2 Vmax

ð! !a Þ

2 =2 CVmax

ð! !a Þ

2 Vmax =R!.

The energy dissipated per cycle in R is Wd ¼ Ws max R=L! ¼ Q ¼ 2 !CR Wd

12.7

Consequently, ð! !a Þ ð! !a Þ

A three-element series circuit contains R ¼ 10 , L ¼ 5 mH, and C ¼ 12:5 mF. Plot the magnitude and angle of Z as functions of ! for values of ! from 0.8 !0 through 1:2 !0 . pﬃﬃﬃﬃﬃﬃﬃ !0 ¼ 1= LC ¼ 4000 rad/s.

At !0 ,

XL ¼ ð4000Þð5 103 Þ ¼ 20

XC ¼

1 ¼ 20

ð4000Þð12:5 106 Þ

Z ¼ 10 þ jðXL XC Þ ¼ 10 þ j0

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

297

The values of the reactances at other frequencies are readily obtained. A tabulation of reactances and impedances appear in Fig. 12-39(a), and Fig. 12-39(b) shows the required plots. !

XL

XC

3200

16

25

10 j9

13:4 428

3600

18

22.2

10 j4:2

10:8 22:88

4000

20

20

10

10 08

4400

22

18.2

10 þ j3:8

10:7 20:88

4800

24

16.7

10 þ j7:3

12:4 36:28

Z

(a)

Fig. 12-39

12.8

Show that !0 ¼

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ !l !h for the series RLC circuit.

By the results of Problem 12.5, 0sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 10sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 2 2 R 1 R R 1 R 1 A@ þ A¼ ¼ !20 !l !h ¼ @ þ þ 2L LC 2L 2L LC 2L LC

12.9

Compute the quality factor of an RLC series circuit, with R ¼ 20 , L ¼ 50 mH, and C ¼ 1 mF, using (a) Q ¼ !0 L=R, (b) Q ¼ 1=!0 CR, and (c) Q ¼ !0 =. 1 !0 ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ 4472 rad=s 0:05 106 sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 2 R R 1 R R 1 þ ¼ 4276:6 rad=s !h ¼ þ ¼ 4676:6 rad=s !l ¼ þ þ 2L 2L LC 2L 2L LC and ¼ !h !l ¼ 400 rad/s. ðaÞ ðbÞ ðcÞ

!0 L 4472ð0:050Þ ¼ ¼ 11:2 R 20 1 1 Q¼ ¼ ¼ 11:2 !0 CR 4472ð106 Þ20 Q¼

Q¼

!0 4472 ¼ 11:2 ¼ 400

298

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

12.10 A coil is represented by a series combination of L ¼ 50 mH and R ¼ 15 . Calculate the quality factor at (a) 10 kHz, (b) 50 kHz. Qcoil ¼

ðaÞ ðcÞ

!L 2ð10 103 Þð50 103 Þ ¼ ¼ 209 R 15 50 ¼ 1047 Qcoil ¼ 209 10

12.11 Convert the circuit constants of Problem 12.10 to the parallel form (a) at 10 kHz, (b) at 250 Hz. " Rp ¼ Rs 1 þ

ðaÞ

# !Ls 2 ¼ Rs ½1 þ Q2s ¼ 15½1 þ ð209Þ2 ¼ 655 k

Rs

or, since Qs 10, Rp Rs Q2s ¼ 15ð209Þ2 ¼ 655 k . 1 Lp ¼ Ls 1 þ 2 Ls ¼ 50 mH Qs (b) At 250 Hz, 2ð250Þð50 103 Þ ¼ 5:24 15 2 Rp ¼ Rs ½1 þ Qs ¼ 15½1 þ ð5:24Þ2 ¼ 426:9

1 1 Lp ¼ Ls 1 þ 2 ¼ ð50 103 Þ 1 þ ¼ 51:8 mH Qs ð5:24Þ2 Qs ¼

Conversion of circuit elements from series to parallel can be carried out at a speciﬁc frequency, the equivalence holding only at that frequency. Note that in (b), where Qs < 10, Lp diﬀers signiﬁcantly from Ls .

12.12 For the circuit shown in Fig. 12-40, (a) obtain the voltage transfer function Hv ð!Þ, and (b) ﬁnd the frequency at which the function is real.

Fig. 12-40 (a) Let Z2 and Y2 represent the impedance and admittance of the R2 LC parallel tank. Hv ð!Þ ¼

¼

Z2 1 ¼ ¼ R1 þ Z2 1 þ R1 Y2

1 1 1 þ j!C þ R2 j!L

1 þ R1

1 R1 1 þ jR1 !C 1þ R2 !L

(b) The transfer function is real when Y2 is real; that is, when 1 ! ¼ !a pﬃﬃﬃﬃﬃﬃﬃ LC At ! ¼ !a , not only are jZ2 j and jHv j maximized, but jZin j ¼ jR1 þ Z2 | also is maximized (because R1 is real and positive—see the locus diagram, Fig. 12-41).

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

299

Fig. 12-41

12.13 Obtain the bandwidth for the circuit of Fig. 12-40 and plot against the parameter Rx

R1 R2 R1 þ R2

Here, the half-power frequencies are determined by the condition jHv ð!Þj ¼ 0:707jHv jmax , or, from Problem 12.12(a), 1 R 1 R1 !C or Rx !C ¼ 1þ 1 ¼ 1 R2 !L !L But (see Section 12.13) this is just the equation for the half-power frequencies of an Rx LC parallel circuit. Hence, ¼

!a 1 ¼ Qa CRx

The hyperbolic graph is shown in Fig. 12-42.

Fig. 12-42

12.14 In the circuit of Fig. 12-40, let R1 ¼ R2 ¼ 2 k , L ¼ 10 mH, and C ¼ 40 nF. Find the resonant frequency and bandwidth, and compare with the results for R1 ¼ 0 (i.e., a pure parallel circuit). 1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ 5 104 rad=s ð10 103 Þð40 109 Þ or fa ¼ 7958 Hz. With Rx ¼ 22 =4 ¼ 1 k , Problem 12.13 gives ¼

1 ¼ 2:5 104 rad=s ð40 109 Þð1 103 Þ

300

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

The results of Problem 12.12 and 12.13 cannot be applied as R1 ! 0, for, in the limit, the voltage ratio is identically unity and so cannot provide any information about the residual R2 LC parallel circuit. (Note that ! 1 as Rx ! 0.) Instead, we must go over to the input impedance function, as in Section 12.13, whereby 1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃ ¼ 5 104 rad=s LC as previously, and ¼

1 ¼ 1:25 104 rad=s CR2

12.15 For the circuit of Fig. 12-40, R1 ¼ 5 k and C ¼ 10 nF. If V2 =V1 ¼ 0:8 08 at 15 kHz, calculate R2 , L, and the bandwidth. An angle of zero on the voltage ratio Hv indicates that the circuit as a whole, and the parallel rank by itself, is at resonance (see Problem 12.14). Then, 1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃ LC

L¼

1 1 ¼ 11:26 mH ¼ !2a C ½2ð15 103 Þ2 ð10 109 Þ

From Problem 12.12, Hv ð!a Þ ¼ 0:8 08 ¼

1 1 þ ðR1 =R2 Þ

whence

R2 ¼

R1 ¼ 20 k

0:25

Then, Rx ¼ ð5Þð20Þ=25 ¼ 4 k , and Problem 12.3 gives ¼

1 ¼ 2:5 104 rad=s ð10 109 Þð4 103 Þ

12.16 Compare the resonant frequency of the circuit shown in Fig. 12-43 for R ¼ 0 to that for R ¼ 50 . For R ¼ 0, the circuit is that of an LC parallel tank, with 1 1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃ ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ 408:2 rad=s LC ð0:2Þð30 106 Þ

or

fa ¼ 65 Hz

For R ¼ 50 , Yin ¼ j!C þ

1 R !L ¼ 2 þ j !C R þ j!L R þ ð!LÞ2 R2 þ ð!LÞ2

For resonance, Im Yin is zero, so that rﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 R2 C !a ¼ pﬃﬃﬃﬃﬃﬃﬃ 1 L LC

Fig. 12-43

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

301

Clearly, as R ! 0, this expression reduces to that given for the pure LC tank. Substituting the numerical values produces a value of 0.791 for the radical; hence, !a ¼ 408:2ð0:791Þ ¼ 322:9 rad=s

or

fa ¼ 51:4 Hz

12.17 Measurements on a practical inductor at 10 MHz give L ¼ 8:0 mH and Qind ¼ 40. (a) Find the ideal capacitance C for parallel resonance at 10 MHz and calculate the corresponding bandwidth . (b) Repeat if a practical capacitor, with a dissipation factor D ¼ Q1 cap ¼ 0:005 at 10 MHz, is used instead of an ideal capacitance. (a) From Section 12.14, 1 1 !a ¼ pﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ LC 1 þ Q2 ind or

C¼

!2a Lð1

1 ¼ þ Q2 ind Þ

1

¼ 31:6 pF 1 ½2ð10 106 Þ2 ð8:0 106 Þ 1 þ 1600

Using Section 12.15 to convert the series RL branch of Fig. 12-25 to parallel at the resonant frequency, ! L Rp ¼ Rð1 þ Q2ind Þ ¼ a ð1 þ Q2ind Þ Qind Then, from Section 12.13, ! !2 L ! Q 2ð10 106 Þð40Þ rad=s ¼ a ¼ a ¼ a ind ¼ 2 Rp 1 þ 1600 Qa 1 þ Qind or 0.25 MHz. (b) The circuit is shown in Fig. 12-44; part (a) gives the resistance of the practical inductor as R¼

!a L ¼ 4

Qind

Also, from the given dissipation factor, it is known that 1 ¼ 0:005 !a CRC The input admittance is 1 1 1 R !L ¼ þ j!C þ þ Yin ¼ þ j !C 2 RC R þ j!L RC R2 þ ð!LÞ2 R þ ð!LÞ2 which diﬀers from the input admittance for part (a) only in the real part. Since the imaginary part involves the same L and the same R, and must vanish at the same frequency, C must be the same as in part (a); namely, C ¼ 31:6 pF. For ﬁxed C, bandwidth is inversely proportional to resistance. With the practical capacitor, the net parallel resistance is R0 ¼

Rp RC Rp þ RC

Fig. 12-44

302

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

where Rp is as calculated in part (a).

[CHAP. 12

Therefore,

Rp Rp ð! L=Qind Þð1 þ Q2ind Þ ¼ 0 ¼1þ ¼1þ a 0:25 MHz R 1=!a Cð0:005Þ RC ð1 þ Q2ind Þð0:005Þ Qind ð1 þ Q2 ind Þ ð1 þ 1600Þð0:005Þ ¼ 1:2 ¼1þ 1 40 1 þ 1600

¼1þ

and so ¼ 0:30 MHz. A lossy capacitor has the same eﬀect as any loading resistor placed across the tank; the Qa is reduced and the bandwidth increased, while fa is unchanged.

12.18 A lossy capacitor, in the series-circuit model, consists of R ¼ 25 and C ¼ 20 pF. Obtain the equivalent parallel model at 50 kHz. From Section 12.15, or by letting L ! 0 in Problem 12.6(a), Qs ¼

1 1 ¼ ¼ 6370 !Cs Rs 2ð50 103 Þð20 1012 Þð25Þ

For this large Qs -value, Rp Rs Q2s ¼ 1010 M

Cp Cs ¼ 20 pF

12.19 A variable-frequency source of V ¼ 100 08 V is applied to a series RL circuit having R ¼ 20

and L ¼ 10 mH. Compute I for ! ¼ 0, 500, 1000, 2000, 5000 rad/s. Plot all currents on the same phasor diagram and note the locus of the currents. Z ¼ R þ jXL ¼ R þ j!L Table 12-2 exhibits the required computations. With the phasor voltage at the angle zero, the locus of I as ! varies is the semicircle shown in Fig. 12-45. Since I ¼ VY, with constant V, Fig. 12-45 is essentially the same as Fig. 12-28(c), the admittance locus diagram for the series RL circuit. Table 12-2 !, rad/s

XL ;

R;

0

0

20

20 08

5 08

500

5

20

20:6 14:048

4:85 14:048

1000

10

20

22:4 26:578

4:46 26:578

2000

20

20

28:3 458

3:54 458

5000

50

20

53:9 68:208

1:86 68:208

Z;

I; A

12.20 The circuit shown in Fig. 12-46 is in resonance for two values of C when the frequency of the driving voltage is 5000 rad/s. Find these two values of C and construct the admittance locus diagram which illustrates this fact. At the given frequency, XL ¼ 3 .

Then the admittance of this ﬁxed branch is

Y1 ¼

1 ¼ 0:147 j0:088 S 5 þ j3

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

Fig. 12-45

303

Fig. 12-46

The semicircular admittance locus of branch 2 has the radius r ¼ 1=2R ¼ 0:125 S. The total admittance is the sum of the ﬁxed admittance Y1 and the variable admittance Y2 . In Fig. 12-47, the semicircular locus is added to the ﬁxed complex number Y1 . The circuit resonance occurs at points a and b, where YT is real. YT ¼ 0:417 j0:088 þ

1 4 jXC

Fig. 12-47 which is real if XC2 11:36XC þ 16 ¼ 0 or XC1 ¼ 9:71 , XC2 ¼ 1:65 .

With ! ¼ 5000 rad/s, C1 ¼ 20:6 mF

C2 ¼ 121 mF

12.21 Show by locus diagrams that the magnitude of the voltage between points A and B in Fig. 12-48 is always one-half the magnitude of the applied voltage V as L is varied.

Fig. 12-48

304

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

Branch-1 current I1 passes through two equal resistors R. Thus A is the midpoint on the phasor V, as shown in Fig. 12-49.

Fig. 12-49 Branch 2 has a semicircular Y-locus [see Fig. 12-28(c)]. Then the current locus is also semicircular, as shown in Fig. 12.50(a). The voltage phasor diagram, Fig. 12-50(b), consists of the voltage across the inductance, VBN , and the voltage across R1 , VMB . The two voltages add vectorially, V ¼ VMN ¼ VBN þ VMB

Fig. 12-50 Because I2 lags VBN by 908, VBN and VMB are perpendicular for all values of L in Fig. 12-50(b). As L varies from 0 to 1, point B moves from N toward M along the semicircle. Figures 12-49 and 12-50(b) are superimposed in Fig. 12-50(c). It is clear that VAB is a radius of the semicircle and therefore, jVAB j ¼ 12 jVj Further, the angle by which VAB lags V is equal to 2, where ¼ tan1 !L=R1 .

Supplementary Problems 12.22

A high-pass RL circuit has R1 ¼ 50 k and L2 ¼ 0:2 mH. (a) Find ! if the magnitude of the voltage transfer function is jHv1 j ¼ 0:90. (b) With a load R ¼ 1 M across L2 , ﬁnd jHv j at ! ¼ 7:5 108 rad/s. Ans: ðaÞ 5:16 108 rad/s; (b) 0.908

12.23

Obtain Hv1 for a high-pass RL circuit at ! ¼ 2:5!x , R ¼ 2 k , L ¼ 0:05 H.

12.24

A low-pass RC circuit under no-load has R1 ¼ 5 k . (a) Find C2 if jHv j ¼ 0:5 at 10 kHz. (b) Obtain Hv at 5 kHz. (c) What value of C2 results in jHv j ¼ 0:90 at 8 kHz? (d) With C2 as in (a), ﬁnd a new value for R1 to result in jHv j ¼ 0:90 at 8 kHz. Ans: ðaÞ 5:51 mF; (b) 0:756 40:898; (c) 1:93 mF; ðdÞ 1749

12.25

A simple voltage divider would consist of R1 and R2 . If stray capacitance Cs is present, then the divider would generally be frequency-dependent. Show, however, that V2 =V1 is independent of frequency for the circuit of Fig. 12-51 if the compensating capacitance C1 has a certain value. Ans: C1 ¼ ðR2 =R1 ÞCs

Ans:

0:928 21:808

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

Fig. 12-51

305

Fig. 12-52

12.26

Assume that a sinusoidal voltage source with a variable frequency and Vmax ¼ 50 V is applied to the circuit shown in Fig. 12-52. (a) At what frequency f is jIj a minimum? (b) Calculate this minimum current. (c) What is jIC j at this frequency? Ans: ðaÞ 2:05 kHz; (b) 2.78 mA; (c) 10.8 mA

12.27

A 20-mF capacitor is in parallel with a practical inductor represented by L ¼ 1 mHz in series with R ¼ 7 . Find the resonant frequency, in rad/s and in Hz, of the parallel circuit. Ans: 1000 rad/s, 159.2 Hz

12.28

What must be the relationship between the values of RL and RC if the network shown in Fig. 12-53 is to be resonant at all frequencies? Ans: RL ¼ RC ¼ 5

Fig. 12-53

Fig. 12-54

12.29

For the parallel network shown in Fig. 12-54, (a) ﬁnd the value of R for resonance; (b) convert the RC branch to a parallel equivalent. Ans: ðaÞ 6:0 ; ðbÞ Rp ¼ 6:67 ; XCp ¼ 20

12.30

For the network of Fig. 12-55(a), ﬁnd R for resonance. Obtain the values of R 0 , XL , and XC in the parallel equivalent of Fig. 12-55(b). Ans: R ¼ 12:25 ; R 0 ¼ 7:75 ; XL ¼ 25 ; XC ¼ 25

Fig. 12-55 12.31

Branch 1 of a two-branch parallel circuit has an impedance Z1 ¼ 8 þ j6 at ! ¼ 5000 rad/s. Branch 2 contains R ¼ 8:34 in series with a variable capacitance C. (a) Find C for resonance. (b) Sketch the admittance locus diagram. Ans: ðaÞ 24 mF ðbÞ See Fig. 12-56

306

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

Fig. 12-56

12.32

[CHAP. 12

Fig. 12-57

Find R for resonance of the network shown in Fig. 12-57. Sketch the admittance locus diagram. Ans: Resonance cannot be achieved by varying R. See Fig. 12-58.

Fig. 12-58

12.33

In Problem 12.32, for what values of the inductive reactance will it be possible to obtain resonance at some value of the variable resistance R? Ans: XL 8:2

12.34

(a) Construct the admittance locus diagram for the circuit shown in Fig. 12-59. resistance in the RL branch is resonance possible for only one value of XL ? Ans: ðaÞ See Fig. 12-60. ðbÞ 6:25 :

Fig. 12-59

(b) For what value of

Fig. 12-60

12.35

Determine the value(s) of L for which the circuit shown in Fig. 12-61 is resonant at 5000 rad/s. Ans: 2:43 mH, 66.0 mH

12.36

A three-branch parallel circuit has ﬁxed elements in two branches; in the third branch, one element is variable. The voltage-current phasor diagram is shown in Fig. 12-62. Identify all the elements if ! ¼ 5000 rad/s.

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

307

Fig. 12-61

Fig. 12-62 Ans:

12.37

Branch 1: R ¼ 8:05 ; L ¼ 0:431 mH Branch 2: R ¼ 4:16 ; C ¼ 27:7 mF Branch 3: L ¼ 2:74 mH, variable R

Describe the circuit which corresponds to each locus in Fig. 12-63 if there is only one variable element in each circuit. Ans: (a) A two-branch parallel circuit. Branch 1: ﬁxed R and XC ; branch 2: ﬁxed R and variable XC . (b) A three-branch parallel circuit. Branch 1: ﬁxed R and XC ; branch 2: ﬁxed XC ; branch 3: ﬁxed R and variable XL . (c) A two-branch parallel circuit. Branch 1: ﬁxed R and XC ; branch 2: ﬁxed XL and variable R.

Fig. 12-63 12.38

In the circuit of Fig. 12-64, L ¼ 1 mH. Determine R1 , R2 , and C such that the impedance between the two terminals of the circuit is 100 at all frequencies. Ans: C ¼ 100 nF, R1 ¼ R2 ¼ 100

12.39

Given V2 =V1 ¼ 10s=ðs2 þ 2s þ 81Þ and v1 ðtÞ ¼ cos ð!tÞ, determine ! such that the amplitude of v2 ðtÞ attains a maximum. Find that maximum. Ans: ! ¼ 9 rad/s, V2 ¼ 5 V

12.40

Given HðsÞ ¼ s=ðs2 þ as þ bÞ determine a and b such that the magnitude of the frequency response jHð!Þj has a maximum at 100 Hz with a half-power bandwidth of 5 Hz. Then ﬁnd the quality factor Q. Ans: a ¼ 31:416; b ¼ 394784; Q ¼ 20

308

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

[CHAP. 12

Fig. 12-64

12.41

Given HðsÞ ¼ ðs þ 1Þ=ðs2 þ 2s þp82Þ, ﬃﬃﬃﬃﬃ determine where jHð!Þj is at a maximum, its half-power bandwidth and quality factor. Ans: !0 ¼ 82 9 rad/s, ! ¼ 2 rad/s, Q ¼ 4:53

12.42

In a parallel RLC circuit R ¼ 10 k and L ¼ 20 mH. (a) Find C so that the circuit resonates at 1 MHz. Find the quality factor Q and the bandwidth in kHz. (b) Find the terminal voltage of the circuit if an AC current source of I ¼ 1 mA is applied to it at: (i) 1 MHz, (ii) 1.01 MHz, (iii) 1.006 MHz Ans: ðaÞ C ¼ 1:267 nF; Q ¼ 79:6; f ¼ 12:56 kHz; (b) V2 ¼ 10 V at 1 MHz, 5.34 V at 1.01 MHz, and 7.24 V at 1.006 MHz

12.43

A coil is modeled as a 50-mH inductor in series with a 5- resistor. Specify the value of a capacitor to be placed in series with the coil so that the circuit would resonate at 600 kHz. Find the quality factor Q and bandwidth f in kHz. Ans: C ¼ 1:4 nF; Q ¼ 37:7; f ¼ 15:9 kHz

12.44

The coil of Problem 12.43 placed in parallel with a capacitor C resonates at 600 kHz. Find C, quality factor Q, and bandwidth f in kHz. Hint: Find the equivalent parallel RLC circuit. Ans: C ¼ 1:4 nF; Q ¼ 37:7; f ¼ 15:9 kHz

12.45

The circuit in Fig. 12-65(a) is a third-order Butterworth low-pass ﬁlter. Find the network function, the magnitude of the frequency response, and its half-power cutoﬀ frequency !0 . Ans: HðsÞ ¼ 1=ðs3 þ 2s2 þ 2s þ 1Þ; jHð!Þj2 ¼ 1=ð1 þ !6 Þ; !0 ¼ 1 rad/s

Fig. 12-65

CHAP. 12]

FREQUENCY RESPONSE, FILTERS, AND RESONANCE

309

12.46

In the circuit of Fig. 12-65(b), let R ¼ 1 ; C1 ¼ 1:394 F; C2 ¼ 0:202 F, and C3 ¼ 3:551 F. Find HðsÞ ¼ V2 =V1 and show that it approximates the passive third-order Butterworth low-pass ﬁlter of Fig. 12-65(a). Ans: HðsÞ ¼ 1=ð0:99992s3 þ 1:99778s2 þ 2s þ 1Þ

12.47

Show that the half-power cutoﬀ frequency in the circuit of Fig. 8-42 is !0 ¼ 1=ðRCÞ and, therefore, frequency scaling may be done by changing the value of C or R. Ans:

12.48

V2 2 2 1 ; !0 ¼ ¼ ¼ 2 V1 R2 C2 s2 þ RCs þ 1 RC s s þ þ1 !0 !0

Find RLC values in the low-pass ﬁlter of Fig. 12-65(a) to move its half-power cutoﬀ frequency to 5 kHz. Ans: R ¼ 1 ; C ¼ 31:83 mF; L ¼ 63:66 mH

Two-Port Networks 13.1

TERMINALS AND PORTS

In a two-terminal network, the terminal voltage is related to the terminal current by the impedance Z ¼ V=I. In a four-terminal network, if each terminal pair (or port) is connected separately to another circuit as in Fig. 13-1, the four variables i1 , i2 , v1 , and v2 are related by two equations called the terminal characteristics. These two equations, plus the terminal characteristics of the connected circuits, provide the necessary and suﬃcient number of equations to solve for the four variables.

Fig. 13-1

13.2

Z-PARAMETERS

The terminal characteristics of a two-port network, having linear elements and dependent sources, may be written in the s-domain as V1 ¼ Z11 I1 þ Z12 I2 V2 ¼ Z21 I1 þ Z22 I2

ð1Þ

The coeﬃcients Zij have the dimension of impedance and are called the Z-parameters of the network. The Z-parameters are also called open-circuit impedance parameters since they may be measured at one terminal while the other terminal is open. They are V1 Z11 ¼ I1 I2 ¼0 V Z12 ¼ 1 I2 I1 ¼0 ð2Þ V Z21 ¼ 2 I1 I2 ¼0 V2 Z22 ¼ I 2

I1 ¼0

310 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

CHAP. 13]

TWO-PORT NETWORKS

311

EXAMPLE 13.1 Find the Z-parameters of the two-port circuit in Fig. 13-2. Apply KVL around the two loops in Fig. 13-2 with loop currents I1 and I2 to obtain V1 ¼ 2I1 þ sðI1 þ I2 Þ ¼ ð2 þ sÞI1 þ sI2 V2 ¼ 3I2 þ sðI1 þ I2 Þ ¼ sI1 þ ð3 þ sÞI2

ð3Þ

Fig. 13-2 By comparing (1) and (3), the Z-parameters of the circuit are found to be Z11 ¼ s þ 2 Z12 ¼ Z21 ¼ s Z22 ¼ s þ 3

ð4Þ

Note that in this example Z12 ¼ Z21 .

Reciprocal and Nonreciprocal Networks A two-port network is called reciprocal if the open-circuit transfer impedances are equal; Z12 ¼ Z21 . Consequently, in a reciprocal two-port network with current I feeding one port, the open-circuit voltage measured at the other port is the same, irrespective of the ports. The voltage is equal to V ¼ Z12 I ¼ Z21 I. Networks containing resistors, inductors, and capacitors are generally reciprocal. Networks that additionally have dependent sources are generally nonreciprocal (see Example 13.2).

EXAMPLE 13.2 The two-port circuit shown in Fig. 13-3 contains a current-dependent voltage source. Find its Z-parameters. As in Example 13.1, we apply KVL around the two loops: V1 ¼ 2I1 I2 þ sðI1 þ I2 Þ ¼ ð2 þ sÞI1 þ ðs 1ÞI2 V2 ¼ 3I2 þ sðI1 þ I2 Þ ¼ sI1 þ ð3 þ sÞI2

Fig. 13-3

312

TWO-PORT NETWORKS

[CHAP. 13

The Z-parameters are Z11 ¼ s þ 2 Z12 ¼ s 1 Z21 ¼ s

ð5Þ

Z22 ¼ s þ 3 With the dependent source in the circuit, Z12 6¼ Z21 and so the two-port circuit is nonreciprocal.

13.3

T-EQUIVALENT OF RECIPROCAL NETWORKS

A reciprocal network may be modeled by its T-equivalent as shown in the circuit of Fig. 13-4. Za , Zb , and Zc are obtained from the Z-parameters as follows. Za ¼ Z11 Z12 Zb ¼ Z22 Z21

ð6Þ

Zc ¼ Z12 ¼ Z21 The T-equivalent network is not necessarily realizable.

Fig. 13-4

EXAMPLE 13.3 Find the Z-parameters of Fig. 13-4. Again we apply KVL to obtain V1 ¼ Za I1 þ Zc ðI1 þ I2 Þ ¼ ðZa þ Zc ÞI1 þ Zc I2 V2 ¼ Zb I2 þ Zc ðI1 þ I2 Þ ¼ Zc I1 þ ðZb þ Zc ÞI2

ð7Þ

By comparing (1) and (7), the Z-parameters are found to be Z11 ¼ Za þ Zc Z12 ¼ Z21 ¼ Zc Z22 ¼ Zb þ Zc

13.4

ð8Þ

Y-PARAMETERS

The terminal characteristics may also be written as in (9), where I1 and I2 are expressed in terms of V1 and V2 . I1 ¼ Y11 V1 þ Y12 V2 I2 ¼ Y21 V1 þ Y22 V2

ð9Þ

The coeﬃcients Yij have the dimension of admittance and are called the Y-parameters or short-circuit admittance parameters because they may be measured at one port while the other port is short-circuited. The Y-parameters are

CHAP. 13]

TWO-PORT NETWORKS

Y11 Y12 Y21 Y22

I1 ¼ V1 V2 ¼0 I1 ¼ V2 V1 ¼0 I ¼ 2 V1 V2 ¼0 I2 ¼ V

313

ð10Þ

2 V1 ¼0

EXAMPLE 13.4

Find the Y-parameters of the circuit in Fig. 13-5.

Fig. 13-5

Fig. 13-6 We apply KCL to the input and output nodes (for convenience, we designate the admittances of the three branches of the circuit by Ya , Yb , and Yc as shown in Fig. 13-6). Thus, 1 3 ¼ 2 þ 5s=3 5s þ 6 1 2 Yb ¼ ¼ 3 þ 5s=2 5s þ 6 1 s ¼ Yc ¼ 5 þ 6=s 5s þ 6

Ya ¼

ð11Þ

The node equations are I1 ¼ V1 Ya þ ðV1 V2 ÞYc ¼ ðYa þ Yc ÞV1 Yc V2 I2 ¼ V2 Yb þ ðV2 V1 ÞYc ¼ Yc V1 þ ðYb þ Yc ÞV2 By comparing (9) with (12), we get

ð12Þ

314

TWO-PORT NETWORKS

[CHAP. 13

Y11 ¼ Ya þ Yc Y12 ¼ Y21 ¼ Yc Y22 ¼ Yb þ Yc

ð13Þ

Substituting Ya , Yb , and Yc in (11) into (13), we ﬁnd Y11 ¼

sþ3 5s þ 6

Y12 ¼ Y21 ¼ Y22 ¼

s 5s þ 6

ð14Þ

sþ2 5s þ 6

Since Y12 ¼ Y21 , the two-port circuit is reciprocal.

13.5

PI-EQUIVALENT OF RECIPROCAL NETWORKS

A reciprocal network may be modeled by its Pi-equivalent as shown in Fig. 13-6. The three elements of the Pi-equivalent network can be found by reverse solution. We ﬁrst ﬁnd the Y-parameters of Fig. 13-6. From (10) we have Y11 ¼ Ya þ Yc Y12 ¼ Yc

[Fig. 13.7ðaÞ [Fig. 13-7ðbÞ

Y21 ¼ Yc Y22 ¼ Yb þ Yc

[Fig. 13-7ðaÞ [Fig. 13-7ðbÞ

ð15Þ

from which Ya ¼ Y11 þ Y12

Yb ¼ Y22 þ Y12

Yc ¼ Y12 ¼ Y21

ð16Þ

The Pi-equivalent network is not necessarily realizable.

Fig. 13-7

13.6

APPLICATION OF TERMINAL CHARACTERISTICS

The four terminal variables I1 , I2 , V1 , and V2 in a two-port network are related by the two equations (1) or (9). By connecting the two-port circuit to the outside as shown in Fig. 13-1, two additional equations are obtained. The four equations then can determine I1 , I2 , V1 , and V2 without any knowledge of the inside structure of the circuit.

CHAP. 13]

EXAMPLE 13.5

315

TWO-PORT NETWORKS

The Z-parameters of a two-port network are given by Z11 ¼ 2s þ 1=s

Z12 ¼ Z21 ¼ 2s

Z22 ¼ 2s þ 4

The network is connected to a source and a load as shown in Fig. 13-8.

Find I1 , I2 , V1 , and V2 .

Fig. 13-8 The terminal characteristics are given by V1 ¼ ð2s þ 1=sÞI1 þ 2sI2 V2 ¼ 2sI1 þ ð2s þ 4ÞI2

ð17Þ

The phasor representation of voltage vs ðtÞ is Vs ¼ 12 V with s ¼ j. From KVL around the input and output loops we obtain the two additional equations (18) Vs ¼ 3I1 þ V1 0 ¼ ð1 þ sÞI2 þ V2

ð18Þ

Substituting s ¼ j and Vs ¼ 12 in (17) and in (18) we get V1 ¼ jI1 þ 2jI2 V2 ¼ 2jI1 þ ð4 þ 2jÞI2 12 ¼ 3I1 þ V1 0 ¼ ð1 þ jÞI2 þ V2 from which I1 ¼ 3:29 10:28 V1 ¼ 2:88 37:58

13.7

I2 ¼ 1:13 131:28 V2 ¼ 1:6 93:88

CONVERSION BETWEEN Z- AND Y-PARAMETERS

The Y-parameters may be obtained from the Z-parameters by solving (1) for I1 and I2 . Applying Cramer’s rule to (1), we get Z22 Z V1 12 V2 DZZ DZZ Z21 Z I2 ¼ V þ 11 V DZZ 1 DZZ 2 I1 ¼

ð19Þ

where DZZ ¼ Z11 Z22 Z12 Z21 is the determinant of the coeﬃcients in (1). By comparing (19) with (9) we have

316

TWO-PORT NETWORKS

[CHAP. 13

Z22 DZZ Z12 ¼ DZZ Z21 ¼ DZZ Z11 ¼ DZZ

Y11 ¼ Y12 Y21 Y22

ð20Þ

Given the Z-parameters, for the Y-parameters to exist, the determinant DZZ must be nonzero. versely, given the Y-parameters, the Z-parameters are Y22 DYY Y12 ¼ DYY Y21 ¼ DYY Y11 ¼ DYY

Con-

Z11 ¼ Z12 Z21 Z22

ð21Þ

where DYY ¼ Y11 Y22 Y12 Y21 is the determinant of the coeﬃcients in (9). For the Z-parameters of a two-port circuit to be derived from its Y-parameters, DYY should be nonzero. EXAMPLE 13.6 Referring to Example 13.4, ﬁnd the Z-parameters of the circuit of Fig. 13-5 from its Y-parameters. The Y-parameters of the circuit were found to be [see (14)] Y11 ¼

sþ3 5s þ 6

Y12 ¼ Y21 ¼

s 5s þ 6

Y22 ¼

sþ2 5s þ 6

Substituting into (21), where DYY ¼ 1=ð5s þ 6Þ, we obtain Z11 ¼ s þ 2 Z12 ¼ Z21 ¼ s

ð22Þ

Z22 ¼ s þ 3 The Z-parameters in (22) are identical to the Z-parameters of the circuit of Fig. 13-2. The two circuits are equivalent as far as the terminals are concerned. This was by design. Figure 13-2 is the T-equivalent of Fig. 13-5. The equivalence between Fig. 13-2 and Fig. 13-5 may be veriﬁed directly by applying (6) to the Z-parameters given in (22) to obtain its T-equivalent network.

13.8

h-PARAMETERS

Some two-port circuits or electronic devices are best characterized by the following terminal equations: V1 ¼ h11 I1 þ h12 V2 I2 ¼ h21 I1 þ h22 V2

ð23Þ

where the hij coeﬃcients are called the hybrid parameters, or h-parameters. EXAMPLE 13.7 Find the h-parameters of Fig. 13-9. This is the simple model of a bipolar junction transistor in its linear region of operation. By inspection, the terminal characteristics of Fig. 13-9 are V1 ¼ 50I1

and

I2 ¼ 300I1

ð24Þ

CHAP. 13]

317

TWO-PORT NETWORKS

Fig. 13-9 By comparing (24) and (23) we get h11 ¼ 50

13.9

h12 ¼ 0

h21 ¼ 300

h22 ¼ 0

ð25Þ

g-PARAMETERS

The terminal characteristics of a two-port circuit may also be described by still another set of hybrid parameters given in (26). I1 ¼ g11 V1 þ g12 I2

ð26Þ

V2 ¼ g21 V1 þ g22 I2 where the coeﬃcients gij are called inverse hybrid or g-parameters. EXAMPLE 13.8

Find the g-parameters in the circuit shown in Fig. 13-10.

Fig. 13-10 This is the simple model of a ﬁeld eﬀect transistor in its linear region of operation. To ﬁnd the g-parameters, we ﬁrst derive the terminal equations by applying Kirchhoﬀ’s laws at the terminals: At the input terminal:

V1 ¼ 109 I1

At the output terminal:

V2 ¼ 10ðI2 103 V1 Þ

or

I1 ¼ 109 V1

and

V2 ¼ 10I2 102 V1

(28)

g21 ¼ 102

ð28Þ

By comparing (27) and (26) we get g11 ¼ 109

13.10

g12 ¼ 0

g22 ¼ 10

TRANSMISSION PARAMETERS

The transmission parameters A, B, C, and D express the required source variables V1 and I1 in terms of the existing destination variables V2 and I2 . They are called ABCD or T-parameters and are deﬁned by

318

TWO-PORT NETWORKS

[CHAP. 13

V1 ¼ AV2 BI2 I1 ¼ CV2 DI2

ð29Þ

EXAMPLE 13.9 Find the T-parameters of Fig. 13-11 where Za and Zb are nonzero.

Fig. 13-11 This is the simple lumped model of an incremental segment of a transmission line. V1 Z þ Zb ¼ a ¼ 1 þ Za Yb V2 I2 ¼0 Zb V B ¼ 1 ¼ Za I2 V2 ¼0 I C ¼ 1 ¼ Yb V2 I2 ¼0 I D ¼ 1 ¼1 I

From (29) we have

A¼

ð30Þ

2 V2 ¼0

13.11

INTERCONNECTING TWO-PORT NETWORKS

Two-port networks may be interconnected in various conﬁgurations, such as series, parallel, or cascade connection, resulting in new two-port networks. For each conﬁguration, certain set of parameters may be more useful than others to describe the network.

Series Connection Figure 13-12 shows a series connection of two two-port networks a and b with open-circuit impedance parameters Za and Zb , respectively. In this conﬁguration, we use the Z-parameters since they are combined as a series connection of two impedances. The Z-parameters of the series connection are (see Problem 13.10):

Fig. 13-12

CHAP. 13]

TWO-PORT NETWORKS

Z11 ¼ Z11;a þ Z11;b Z12 ¼ Z12;a þ Z12;b Z21 ¼ Z21;a þ Z21;b

319

ð31aÞ

Z22 ¼ Z22;a þ Z22;b or, in the matrix form, ½Z ¼ ½Za þ ½Zb

ð31bÞ

Parallel Connection Figure 13-13 shows a parallel connection of two-port networks a and b with short-circuit admittance parameters Ya and Yb . In this case, the Y-parameters are convenient to work with. The Y-parameters of the parallel connection are (see Problem 13.11): Y11 ¼ Y11;a þ Y11;b Y12 ¼ Y12;a þ Y12;b Y21 ¼ Y21;a þ Y21;b Y22 ¼ Y22;a þ Y22;b

ð32aÞ

or, in the matrix form ½Y ¼ ½Ya þ ½Yb

ð32bÞ

Fig. 13-13

Cascade Connection The cascade connection of two-port networks a and b is shown in Fig. 13-14. In this case the T-parameters are particularly convenient. The T-parameters of the cascade combination are

A ¼ Aa Ab þ Ba Cb B ¼ Aa Bb þ Ba Db C ¼ Ca Ab þ Da Cb

ð33aÞ

D ¼ Ca Bb þ Da Db

or, in the matrix form,

½T ¼ ½Ta ½Tb

ð33bÞ

320

TWO-PORT NETWORKS

[CHAP. 13

Fig. 13-14

13.12

CHOICE OF PARAMETER TYPE

What types of parameters are appropriate to and can best describe a given two-port network or device? Several factors inﬂuence the choice of parameters. (1) It is possible that some types of parameters do not exist as they may not be deﬁned at all (see Example 13.10). (2) Some parameters are more convenient to work with when the network is connected to other networks, as shown in Section 13.11. In this regard, by converting the two-port network to its T- and Pi-equivalent and then applying the familiar analysis techniques, such as element reduction and current division, we can greatly reduce and simplify the overall circuit. (3) For some networks or devices, a certain type of parameter produces better computational accuracy and better sensitivity when used within the interconnected circuit. EXAMPLE 13.10 Find the Z- and Y-parameters of Fig. 13-15.

Fig. 13-15 We apply KVL to the input and output loops. Thus, Input loop: Output loop:

V1 ¼ 3I1 þ 3ðI1 þ I2 Þ V2 ¼ 7I1 þ 2I2 þ 3ðI1 þ I2 Þ

or

V1 ¼ 6I1 þ 3I2

and

V2 ¼ 10I1 þ 5I2

(34)

By comparing (34) and (2) we get Z11 ¼ 6

Z12 ¼ 3

Z21 ¼ 10

Z22 ¼ 5

The Y-parameters are, however, not deﬁned, since the application of the direct method of (10) or the conversion from Z-parameters (19) produces DZZ ¼ 6ð5Þ 3ð10Þ ¼ 0.

13.13

SUMMARY OF TERMINAL PARAMETERS AND CONVERSION

Terminal parameters are deﬁned by the following equations Z-parameters V1 ¼ Z11 I1 þ Z12 I2 V2 ¼ Z21 I1 þ Z22 I2 ½V ¼ ½Z½I

h-parameters V1 ¼ h11 I1 þ h12 V2 I2 ¼ h21 I1 þ h22 V2

Y-parameters I1 ¼ Y11 V1 þ Y12 V2 I2 ¼ Y21 V1 þ Y22 V2 ½I ¼ ½Y½V

g-parameters I1 ¼ g11 V1 þ g12 I2 V2 ¼ g21 V1 þ g22 I2

T-parameters V1 ¼ AV2 BI2 I1 ¼ CV2 DI2

CHAP. 13]

321

TWO-PORT NETWORKS

Table 13-1 summarizes the conversion between the Z-, Y-, h-, g-, and T-parameters. conversion to be possible, the determinant of the source parameters must be nonzero.

For the

Table 13-1 Z

Z

Y

h

g

T

Y

h

T

g

Z11

Z12

Y22 DYY

Y12 DYY

Dhh h22

h12 h22

1 g11

g12 g11

A C

DTT C

Z21

Z22

Y21 DYY

Y11 DYY

h21 h22

1 h22

g21 g11

1 C

D C

Z22 Dzz

Z12 Dzz

Y11

Y12

1 h11

h12 h11

Dgg g22

Dgg g11 g12 g22

D B

DTT B

Z21 Dzz

Z11 Dzz

Y21

Y22

h21 h11

Dnn h11

g21 g22

1 B

A B

Dzz Z22

Z12 Z22

1 Y11

Y12 Y11

h11

h12

g22 Dgg

1 g22 g12 Dgg

B D

DTT D

Z21 Z22

1 Z22

Y21 Y11

Dyy Y11

h21

h22

g21 Dgg

g11 Dgg

1 D

C D

1 Z11

Z12 Z11

DYY Y22

Y12 Y22

h22 Dhh

h12 Dhh

g11

g12

C A

DTT A

Z21 Z11

DZZ Z11

Y21 Y22

1 Y22

h21 Dhh

h11 Dhh

g21

g22

1 A

B A

Z11 Z21

DZZ Z21

Y22 Y21

1 Y21

Dhh h21

h11 h21

g22 g21

A

B

1 Z21

Z22 Z21

DYY Y21

Y11 Y21

h22 h21

1 h21

1 g21 g11 g21

Dgg g21

C

D

DPP ¼ P11 P22 P12 P21 is the determinant of Z; Y; h; g; or T-parameters.

Solved Problems 13.1

Find the Z-parameters of the circuit in Fig. 13-16(a). Z11 and Z21 are obtained by connecting a source to port #1 and leaving port #2 open [Fig. 13-16(b)]. The parallel and series combination of resistors produces Z11 ¼

V1 ¼8 I1 I2 ¼0

and

Z21 ¼

V2 1 ¼ I1 I2 ¼0 3

Similarly, Z22 and Z12 are obtained by connecting a source to port #2 and leaving port #1 open [Fig. 13-16(c)]. Z22 ¼

V2 8 ¼ I2 I1 ¼0 9

The circuit is reciprocal, since Z12 ¼ Z21 .

Z12 ¼

V1 1 ¼ I2 I1 ¼0 3

322

TWO-PORT NETWORKS

[CHAP. 13

Fig. 13-16

13.2

The Z-parameters of a two-port network N are given by Z11 ¼ 2s þ 1=s

Z12 ¼ Z21 ¼ 2s

Z22 ¼ 2s þ 4

(a) Find the T-equivalent of N. (b) The network N is connected to a source and a load as shown in the circuit of Fig. 13-8. Replace N by its T-equivalent and then solve for i1 , i2 , v1 , and v2 . (a) The three branches of the T-equivalent network (Fig. 13-4) are 1 1 Za ¼ Z11 Z12 ¼ 2s þ 2s ¼ s s Zb ¼ Z22 Z12 ¼ 2s þ 4 2s ¼ 4 Zc ¼ Z12 ¼ Z21 ¼ 2s (b) The T-equivalent of N, along with its input and output connections, is shown in phasor domain in Fig. 13-17.

Fig. 13-17

CHAP. 13]

TWO-PORT NETWORKS

323

By applying the familiar analysis techniques, including element reduction and current division, to Fig. 13-17, we ﬁnd i1 , i2 , v1 , and v2 . In phasor domain I1 I2 V1 V2

13.3

In the time domain:

¼ 3:29 10:28 ¼ 1:13 131:28 ¼ 2:88 37:58 ¼ 1:6 93:88

i1 ¼ 3:29 cos ðt 10:28Þ i2 ¼ 1:13 cos ðt 131:28Þ v1 ¼ 2:88 cos ðt þ 37:58Þ v2 ¼ 1:6 cos ðt þ 93:88Þ

Find the Z-parameters of the two-port network in Fig. 13-18.

Fig. 13-18 KVL applied to the input and output ports obtains the following: Input port: Output port:

V1 ¼ 4I1 3I2 þ ðI1 þ I2 Þ ¼ 5I1 2I2 V2 ¼ I2 þ ðI1 þ I2 Þ ¼ I1 þ 2I2

By applying (2) to the above, Z11 ¼ 5, Z12 ¼ 2, Z21 ¼ 1, and Z22 ¼ 2:

13.4

Find the Z-parameters of the two-port network in Fig. 13-19 and compare the results with those of Problem 13.3.

Fig. 13-19 KVL gives V1 ¼ 5I1 2I2

and

V2 ¼ I1 þ 2I2

The above equations are identical with the terminal characteristics obtained for the network of Fig. 13-18. Thus, the two networks are equivalent.

13.5

Find the Y-parameters of Fig. 13-19 using its Z-parameters. From Problem 13.4, Z11 ¼ 5; Z12 ¼ 2; Z21 ¼ 1; Z22 ¼ 2

324

TWO-PORT NETWORKS

[CHAP. 13

Since DZZ ¼ Z11 Z22 Z12 Z21 ¼ ð5Þð2Þ ð2Þð1Þ ¼ 12, Y11 ¼

13.6

Z22 2 1 ¼ ¼ DZZ 12 6

Y12 ¼

Z12 2 1 ¼ ¼ 12 6 DZZ

Y21 ¼

Z21 1 ¼ 12 DZZ

Y22 ¼

Z11 5 ¼ DZZ 12

Find the Y-parameters of the two-port network in Fig. 13-20 and thus show that the networks of Figs. 13-19 and 13-20 are equivalent.

Fig. 13-20 Apply KCL at the ports to obtain the terminal characteristics and Y-parameters. Input port:

I1 ¼

Output port: and

V1 V2 þ 6 6 V2 V1 I2 ¼ 2:4 12 1 1 Y21 ¼ ¼ 6 12

Thus,

Y11 ¼

1 6

Y12

Y22 ¼

1 5 ¼ 2:4 12

which are identical with the Y-parameters obtained in Problem 3.5 for Fig. 13-19. Thus, the two networks are equivalent.

13.7

Apply the short-circuit equations (10) to ﬁnd the Y-parameters of the two-port network in Fig. 13-21.

Fig. 13-21

1 1 1 þ V or Y11 ¼ 12 12 1 6 V2 V2 1 1 1 V ¼ or Y12 ¼ ¼ 4 12 2 6 4 12 V1 1 ¼ or Y21 ¼ 12 12 V2 V2 1 1 5 þ þ ¼ ¼ or Y22 ¼ V 3 12 2 12 3 12

I1 ¼ Y11 V1 jV2 ¼0 ¼ I1 ¼ Y12 V2 jV1 ¼0 I2 ¼ Y21 V1 jV2 ¼0 I2 ¼ Y22 V2 jV1 ¼0

CHAP. 13]

13.8

325

TWO-PORT NETWORKS

Apply KCL at the nodes of the network in Fig. 13-21 to obtain its terminal characteristics and Yparameters. Show that two-port networks of Figs. 13-18 to 13-21 are all equivalent. Input node: Output node:

V1 V1 V2 V2 þ þ 12 12 4 V2 V2 V1 I2 ¼ þ 3 12 1 1 1 5 I2 ¼ V1 þ V2 I1 ¼ V 1 þ V 2 6 6 12 12 I1 ¼

The Y-parameters observed from the above characteristic equations are identical with the Y-parameters of the circuits in Figs. 13-18, 13-19, and 13-20. Therefore, the four circuits are equivalent.

13.9

Z-parameters of the two-port network N in Fig. 13-22(a) are Z11 ¼ 4s, Z12 ¼ Z21 ¼ 3s, and Z22 ¼ 9s. (a) Replace N by its T-equivalent. (b) Use part (a) to ﬁnd input current i1 for vs ¼ cos 1000t (V). (a) The network is reciprocal. Therefore, its T-equivalent exists. shown in the circuit of Fig. 13-22(b).

Fig. 13-22

Its elements are found from (6) and

326

TWO-PORT NETWORKS

[CHAP. 13

Za ¼ Z11 Z12 ¼ 4s 3s ¼ s Zb ¼ Z22 Z21 ¼ 9s 3s ¼ 6s Zc ¼ Z12 ¼ Z21 ¼ 3s (b) We repeatedly combine the series and parallel elements of Fig. 13-22(b), with resistors being in k and s in krad/s, to ﬁnd Zin in k as shown in the following. Zin ðsÞ ¼ Vs =I1 ¼ s þ

ð3s þ 6Þð6s þ 12Þ ¼ 3s þ 4 9s þ 18

and i1 ¼ 0:2 cos ð1000t 36:98Þ

or

Zin ð jÞ ¼ 3j þ 4 ¼ 5 36:98 k

(mA).

13.10 Two two-port networks a and b, with open-circuit impedances Za and Zb , are connected in series (see Fig. 13-12). Derive the Z-parameters equations (31a). From network a we have V1a ¼ Z11;a I1a þ Z12;a I2a V2a ¼ Z21;a I1a þ Z22;a I2a From network b we have V1b ¼ Z11;b I1b þ Z12;b I2b V2b ¼ Z21;b I1b þ Z22;b I2b From connection between a and b we have I1 ¼ I1a ¼ I1b

V1 ¼ V1a þ V1b

I2 ¼ I2a ¼ I2b

V2 ¼ V2a þ V2b

Therefore, V1 ¼ ðZ11;a þ Z11;b ÞI1 þ ðZ12;a þ Z12;b ÞI2 V2 ¼ ðZ21;a þ Z21;b ÞI1 þ ðZ22;a þ Z22;b ÞI2 from which the Z-parameters (31a) are derived.

13.11 Two two-port networks a and b, with short-circuit admittances Ya and Yb , are connected in parallel (see Fig. 13-13). Derive the Y-parameters equations (32a). From network a we have I1a ¼ Y11;a V1a þ Y12;a V2a I2a ¼ Y21;a V1a þ Y22;a V2a and from network b we have I1b ¼ Y11;b V1b þ Y12;b V2b I2b ¼ Y21;b V1b þ Y22;b V2b From connection between a and b we have V1 ¼ V1a ¼ V1b V2 ¼ V2a ¼ V2b

I1 ¼ I1a þ I1b I2 ¼ I2a þ I2b

Therefore, I1 ¼ ðY11;a þ Y11;b ÞV1 þ ðY12;a þ Y12;b ÞV2 I2 ¼ ðY21;a þ Y21;b ÞV1 þ ðY22;a þ Y22;b ÞV2 from which the Y-parameters of (32a) result.

CHAP. 13]

327

TWO-PORT NETWORKS

13.12 Find (a) the Z-parameters of the circuit of Fig. 13-23(a) and (b) an equivalent model which uses three positive-valued resistors and one dependent voltage source.

Fig. 13-23 (a) From application of KVL around the input and output loops we ﬁnd, respectively, V1 ¼ 2I1 2I2 þ 2ðI1 þ I2 Þ ¼ 4I1 V2 ¼ 3I2 þ 2ðI1 þ I2 Þ ¼ 2I1 þ 5I2 The Z-parameters are Z11 ¼ 4, Z12 ¼ 0, Z21 ¼ 2, and Z22 ¼ 5. (b) The circuit of Fig. 13-23(b), with two resistors and a voltage source, has the same Z-parameters as the circuit of Fig. 13-23(a). This can be veriﬁed by applying KVL to its input and output loops.

13.13 (a) Obtain the Y-parameters of the circuit in Fig. 13-23(a) from its Z-parameters. (b) Find an equivalent model which uses two positive-valued resistors and one dependent current source. (a) From Problem 13.12, Z11 ¼ 4, Z12 ¼ 0, Z21 ¼ 2; Z22 ¼ 5, and so DZZ ¼ Z11 Z22 Z12 Z21 ¼ 20. Hence, Y11 ¼

Z22 5 1 ¼ ¼ DZZ 20 4

Y12 ¼

Z12 ¼0 DZZ

Y21 ¼

Z21 2 1 ¼ ¼ 20 10 DZZ

Y22 ¼

Z11 4 1 ¼ ¼ DZZ 20 5

(b) Figure 13-24, with two resistors and a current source, has the same Y-parameters as the circuit in Fig. 13-23(a). This can be veriﬁed by applying KCL to the input and output nodes.

13.14 Referring to the network of Fig. 13-23(b), convert the voltage source and its series resistor to its Norton equivalent and show that the resulting network is identical with that in Fig. 13-24. The Norton equivalent current source is IN ¼ 2I1 =5 ¼ 0:4I1 . But I1 ¼ V1 =4. Therefore, IN ¼ 0:4I1 ¼ 0:1V1 . The 5- resistor is then placed in parallel with IN . The circuit is shown in Fig. 13-25 which is the same as the circuit in Fig. 13-24.

Fig. 13-24

Fig. 13-25

328

TWO-PORT NETWORKS

[CHAP. 13

13.15 The h-parameters of a two-port network are given. Show that the network may be modeled by the network in Fig. 13-26 where h11 is an impedance, h12 is a voltage gain, h21 is a current gain, and h22 is an admittance.

Fig. 13-26 Apply KVL around the input loop to get V1 ¼ h11 I1 þ h12 V2 Apply KCL at the output node to get I2 ¼ h21 I1 þ h22 V2 These results agree with the deﬁnition of h-parameters given in (23).

13.16 Find the h-parameters of the circuit in Fig. 13-25. By comparing the circuit in Fig. 13-25 with that in Fig. 13-26, we ﬁnd h11 ¼ 4 ;

h12 ¼ 0;

h21 ¼ 0:4;

h22 ¼ 1=5 ¼ 0:2 1

13.17 Find the h-parameters of the circuit in Fig. 13-25 from its Z-parameters and compare with results of Problem 13.16. Refer to Problem 13.13 for the values of the Z-parameters and DZZ . Use Table 13-1 for the conversion of the Z-parameters to the h-parameters of the circuit. Thus, h11 ¼

DZZ 20 ¼4 ¼ 5 Z22

h12 ¼

Z12 ¼0 Z22

h21 ¼

Z21 2 ¼ 0:4 ¼ 5 Z22

h22 ¼

1 1 ¼ ¼ 0:2 Z22 5

The above results agree with the results of Problem 13.16.

13.18 The simpliﬁed model of a bipolar junction transistor for small signals is shown in the circuit of Fig. 13-27. Find its h-parameters.

Fig. 13-27 The terminal equations are V1 ¼ 0 and I2 ¼ I1 . By comparing these equations with (23), we conclude that h11 ¼ h12 ¼ h22 ¼ 0 and h21 ¼ .

CHAP. 13]

329

TWO-PORT NETWORKS

13.19 h-parameters of a two-port device H are given by h11 ¼ 500

h12 ¼ 104

h21 ¼ 100

h22 ¼ 2ð106 Þ 1

Draw a circuit model of the device made of two resistors and two dependent sources including the values of each element. From comparison with Fig. 13-26, we draw the model of Fig. 13-28.

Fig. 13-28

13.20 The device H of Problem 13-19 is placed in the circuit of Fig. 13-29(a). Replace H by its model of Fig. 13-28 and ﬁnd V2 =Vs .

Fig. 13-29

330

TWO-PORT NETWORKS

The circuit of Fig. 13-29(b) contains the model. 13-29(c) from which I1 ¼ Vs =2000

[CHAP. 13

With good approximation, we can reduce it to Fig.

V2 ¼ 1000ð100I1 Þ ¼ 1000ð100Vs =2000Þ ¼ 50Vs

Thus, V2 =Vs ¼ 50.

13.21 A load ZL is connected to the output of a two-port device N (Fig. 13-30) whose terminal characteristics are given by V1 ¼ ð1=NÞV2 and I1 ¼ NI2 . Find (a) the T-parameters of N and (b) the input impedance Zin ¼ V1 =I1 .

Fig. 13-30 (a) The T-parameters are deﬁned by [see (29)] V1 ¼ AV2 BI2 I1 ¼ CV2 DI2 The terminal characteristics of the device are V1 ¼ ð1=NÞV2 I1 ¼ NI2 By comparing the two pairs of equations we get A ¼ 1=N, B ¼ 0, C ¼ 0, and D ¼ N. (b) Three equations relating V1 , I1 , V2 , and I2 are available: two equations are given by the terminal characteristics of the device and the third equation comes from the connection to the load, V2 ¼ ZL I2 By eliminating V2 and I2 in these three equations, we get V1 ¼ ZL I1 =N 2

from which

Zin ¼ V1 =I1 ¼ ZL =N 2

Supplementary Problems 13.22

The Z-parameters of the two-port network N in Fig. 13-22(a) are Z11 ¼ 4s, Z12 ¼ Z21 ¼ 3s, and Z22 ¼ 9s. Find the input current i1 for vs ¼ cos 1000t (V) by using the open circuit impedance terminal characteristic equations of N, together with KCL equations at nodes A, B, and C. Ans: i1 ¼ 0:2 cos ð1000t 36:98Þ (A)

13.23

Express the reciprocity criteria in terms of h-, g-, and T-parameters. Ans: h12 þ h21 ¼ 0, g12 þ g21 ¼ 0, and AD BC ¼ 1

13.24

Find the T-parameters of a two-port device whose Z-parameters are Z11 ¼ s, Z12 ¼ Z21 ¼ 10s, and Z22 ¼ 100s. Ans: A ¼ 0:1; B ¼ 0; C ¼ 101 =s, and D ¼ 10

13.25

Find the T-parameters of a two-port device whose Z-parameters are Z11 ¼ 106 s, Z12 ¼ Z21 ¼ 107 s, and Z22 ¼ 108 s. Compare with the results of Problem 13.21.

CHAP. 13]

Ans:

13.26

TWO-PORT NETWORKS

331

A ¼ 0:1; B ¼ 0; C ¼ 107 =s and D ¼ 10. For high frequencies, the device is similar to the device of Problem 13.21, with N ¼ 10.

The Z-parameters of a two-port device N are Z11 ¼ ks, Z12 ¼ Z21 ¼ 10ks, and Z22 ¼ 100ks. A 1- resistor is connected across the output port (Fig. 13-30). (a) Find the input impedance Zin ¼ V1 =I1 and construct its equivalent circuit. (b) Give the values of the elements for k ¼ 1 and 106 . Ans:

ðaÞ Zin ¼

ks 1 ¼ 1 þ 100ks 100 þ 1=ks

The equivalent circuit is a parallel RL circuit with R ¼ 102 and L ¼ 1 kH: 1 1

and L ¼ 1 H. For k ¼ 106 ; R ¼

and L ¼ 106 H ðbÞ For k ¼ 1; R ¼ 100 100 13.27

The device pN in ﬃ Fig. 13-30 is speciﬁed by its following Z-parameters: Z22 ¼ N 2 Z11 and ﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Z12 ¼ Z21 ¼ Z11 Z22 ¼ NZ11 . Find Zin ¼ V1 =I1 when a load ZL is connected to the output terminal. Show that if Z11 ZL =N 2 we have impedance scaling such that Zin ¼ ZL =N 2 . Ans:

13.28

Zin ¼

ZL . N 2 þ ZL =Z11

For ZL N 2 Z11 ; Zin ¼ ZL =N 2

Find the Z-parameters in the circuit of Fig. 13-31. Ans: Z11 ¼ Z22 ¼ s þ 3 þ 1=s; Z12 ¼ Z21 ¼ s þ 1

Hint: Use the series connection rule.

Fig. 13-31 13.29

Find the Y-parameters in the circuit of Fig. 13-32. Hint: Use the parallel connection rule. Ans: Y11 ¼ Y22 ¼ 9ðs þ 2Þ=16; Y12 ¼ Y21 ¼ 3ðs þ 2Þ=16

Fig. 13-32

332

TWO-PORT NETWORKS

[CHAP. 13

13.30

Two two-port networks a and b with transmission parameters Ta and Tb are connected in cascade (Fig. 1314). Given I2a ¼ I1b and V2a ¼ V1b , ﬁnd the T-parameters of the resulting two-port network. Ans: A ¼ Aa Ab þ Ba Cb , B ¼ Aa Bb þ Ba Db , C ¼ Ca Ab þ Da Cb , D ¼ Ca Bb þ Da Db

13.31

Find the T- and Z-parameters of the network in Fig. 13-33. The impedances of capacitors are given. Hint: Use the cascade connection rule. Ans: A ¼ 5j 4, B ¼ 4j þ 2, C ¼ 2j 4, and D ¼ j3, Z11 ¼ 1:3 0:6j, Z22 ¼ 0:3 0:6j, Z12 ¼ Z21 ¼ 0:2 0:1j

Fig. 13-33 13.32

Find the Z-parameters of the two-port circuit of Fig. 13-34. Ans: Z11 ¼ Z22 ¼ 12 ðZb þ Za Þ; Z12 ¼ Z21 ¼ 12 ðZb Za Þ

Fig. 13-34

13.33

Find the Z-parameters of the two-port circuit of Fig. 13-35. Ans:

Z11 ¼ Z22 ¼

1 Zb ð2Za þ Zb Þ 1 Z2b ; Z12 ¼ Z21 ¼ 2 Za þ Zb 2 Za þ Zb

Fig. 13-35 13.34

Referring to the two-port circuit of Fig. 13-36, ﬁnd the T-parameters as a function of ! and specify their values at ! ¼ 1, 103 , and 106 rad/s.

CHAP. 13]

Ans:

TWO-PORT NETWORKS

333

A ¼ 1 109 !2 þ j109 !, B ¼ 103 ð1 þ j!Þ, C ¼ 106 j!, and D ¼ 1. At ! ¼ 1 rad/s, A ¼ 1, B ¼ 103 ð1 þ jÞ, C ¼ 106 j, and D ¼ 1. At ! ¼ 103 rad/s, A 1, B j, C ¼ 103 j, and D ¼ 1. At ! ¼ 106 rad/s, A 103 , B 103 j, C ¼ j, and D ¼ 1

Fig. 13-36 13.35

A two-port network contains resistors, capacitors, and inductors only. With port #2 open [Fig. 13-37(a)], a unit step voltage v1 ¼ uðtÞ produces i1 ¼ et uðtÞ ðmAÞ and v2 ¼ ð1 et ÞuðtÞ (V). With port #2 shortcircuited [Fig. 13-37(b)], a unit step voltage v1 ¼ uðtÞ delivers a current i1 ¼ 0:5ð1 þ e2t ÞuðtÞ ðmAÞ. Find i2 and the T-equivalent network. Ans: i2 ¼ 0:5ð1 þ e2t ÞuðtÞ [see Fig. 13-37(c)]

Fig. 13-37 13.36

The two-port network N in Fig. 13-38 is speciﬁed by Z11 ¼ 2, Z12 ¼ Z21 ¼ 1, and Z22 ¼ 4. Find I1 , I2 , and I3 . Ans: I1 ¼ 24 A; I2 ¼ 1:5 A; and I3 ¼ 6:5 A

Fig. 13-38

Mutual Inductance and Transformers 14.1

MUTUAL INDUCTANCE

The total magnetic ﬂux linkage in a linear inductor made of a coil is proportional to the current passing through it; that is, ¼ Li (see Fig. 14-1). By Faraday’s law, the voltage across the inductor is equal to the time derivative of the total inﬂux linkage; that is, v¼

d di ¼L dt dt

Fig. 14-1

The coeﬃcient L, in H, is called the self-inductance of the coil. Two conductors from diﬀerent circuits in close proximity to each other are magnetically coupled to a degree that depends upon the physical arrangement and the rates of change of the currents. This coupling is increased when one coil is wound over another. If, in addition, a soft-iron core provides a path for the magnetic ﬂux, the coupling is maximized. (However, the presence of iron can introduce nonlinearity.) To ﬁnd the voltage-current relation at the terminals of the two coupled coils shown in Fig. 14-2, we observe that the total magnetic ﬂux linkage in each coil is produced by currents i1 and i2 and the mutual linkage eﬀect between the two coils is symmetrical. 1 ¼ L1 i1 þ Mi2 2 ¼ Mi1 þ L2 i2 334 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

ð1Þ

CHAP. 14]

335

MUTUAL INDUCTANCE AND TRANSFORMERS

Fig. 14-2

where M is the mutual inductance (in H). The terminal voltages are time derivatives of the ﬂux linkages. d1 di ¼ L1 1 þ M dt dt d2 di1 ¼M þ L2 v2 ðtÞ ¼ dt dt

v1 ðtÞ ¼

di2 dt di2 dt

ð2Þ

The coupled coils constitute a special case of a two-port network discussed in Chapter 13. The terminal characteristics (2) may also be expressed in the frequency domain or in the s-domain as follows. Frequency Domain V1 ¼ j!L1 I1 þ j!MI2 V2 ¼ j!MI1 þ j!L2 I2

s-Domain V1 ¼ L1 sI1 þ MsI2

ð3Þ

V2 ¼ MsI1 þ L2 sI2

ð4Þ

The coupling coeﬃcient M is discussed in Section 14.2. The frequency domain equations (3) deal with the sinusoidal steady state. The s-domain equations (4) assume exponential sources with complex frequency s. EXAMPLE 14.1 Given L1 ¼ 0:1 H, L2 ¼ 0:5 H, and i1 ðtÞ ¼ i2 ðtÞ ¼ sin !t in the coupled coils of Fig. 14-2. v1 ðtÞ and v2 ðtÞ for (a) M ¼ 0:01 H, ðbÞ M ¼ 0:2 H, and (c) M ¼ 0:2 H. ðaÞ

v1 ðtÞ ¼ 0:1 ! cos !t þ 0:01 ! cos !t ¼ 0:11 ! cos !t v2 ðtÞ ¼ 0:01 ! cos !t þ 0:5 ! cos !t ¼ 0:51 ! cos !t

ðbÞ

v1 ðtÞ ¼ 0:1 ! cos !t þ 0:2 ! cos !t ¼ 0:3 ! cos !t ðVÞ

Find

ðVÞ ðVÞ

v2 ðtÞ ¼ 0:2 ! cos !t þ 0:5 ! cos !t ¼ 0:7 ! cos !t ðVÞ ðcÞ

14.2

v1 ðtÞ ¼ 0:1 ! cos !t 0:2 ! cos !t ¼ 0:1 ! cos !t v2 ðtÞ ¼ 0:2 ! cos !t þ 0:5 ! cos !t ¼ 0:3 ! cos !t

ðVÞ ðVÞ

COUPLING COEFFICIENT

A coil containing N turns with magnetic ﬂux linking each turn has total magnetic ﬂux linkage ¼ N. By Faraday’s law, the induced emf (voltage) in the coil is e ¼ d=dt ¼ Nðd=dtÞ. A negative sign is frequently included in this equation to signal that the voltage polarity is established according to Lenz’s law. By deﬁnition of self-inductance this voltage is also given by Lðdi=dtÞ; hence, L

di d ¼N dt dt

or

L¼N

d di

ð5aÞ

336

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

The unit of being the weber, where 1 Wb ¼ 1 V s, it follows from the above relation that 1 H ¼ 1 Wb=A. Throughout this book it has been assumed that and i are proportional to each other, making L¼N

¼ constant i

ð5bÞ

In Fig. 14-3, the total ﬂux 1 resulting from current i1 through the turns N1 consists of leakage ﬂux, 11 , and coupling or linking ﬂux, 12 . The induced emf in the coupled coil is given by N2 ðd12 =dt). This same voltage can be written using the mutual inductance M: e¼M

di1 d12 ¼ N2 dt dt

or

M ¼ N2

d12 di1

ð6Þ

Fig. 14-3

Also, as the coupling is bilateral, M ¼ N1

d21 di2

ð7Þ

The coupling coeﬃcient, k, is deﬁned as the ratio of linking ﬂux to total ﬂux: k

12 21 ¼ 1 2

where 0 k 1. Taking the product of (6) and (7) and assuming that k depends only on the geometry of the system, d12 d21 dðk1 Þ dðk2 Þ d1 d2 M 2 ¼ N2 N1 ¼ N2 N1 ¼ k2 N1 N2 ¼ k2 L1 L2 di1 di2 di1 di2 di1 di2 pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ or XM ¼ k X1 X2 (8) from which M ¼ k L1 L2 pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Note that (8) implies that M L1 L2 , a bound that may be independently derived by an energy argument. If all of the ﬂux links the coils without any leakage ﬂux, then k ¼ 1. On the other extreme, the coil axes may be oriented such that no ﬂux from one can induce a voltage in the other, which results in k ¼ 0. The term close coupling is used to describe the case where most of the ﬂux links the coils, either by way of a magnetic core to contain the ﬂux or by interleaving the turns of the coils directly over one another. Coils placed side-by-side without a core are loosely coupled and have correspondingly low values of k.

14.3 ANALYSIS OF COUPLED COILS Polarities in Close Coupling In Fig. 14-4, two coils are shown on a common core which channels the magnetic ﬂux . This arrangement results in close coupling, which was mentioned in Section 14.2. To determine the proper signs on the voltages of mutual inductance, apply the right-hand rule to each coil: If the ﬁngers wrap

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

337

Fig. 14-4

around in the direction of the assumed current, the thumb points in the direction of the ﬂux. Resulting positive directions for 1 and 2 are shown on the ﬁgure. If ﬂuxes 1 and 2 aid one another, then the signs on the voltages of mutual inductance are the same as the signs on the voltages of self-inductance. Thus, the plus sign would be written in all four equations (2) and (3). In Fig. 14-4, 1 and 2 oppose each other; consequently, the equations (2) and (3) would be written with the minus sign.

Natural Current Further understanding of coupled coils is achieved from consideration of a passive second loop as shown in Fig. 14-5. Source v1 drives a current i1 , with a corresponding ﬂux 1 as shown. Now Lenz’s law implies that the polarity of the induced voltage in the second circuit is such that if the circuit is completed, a current will pass through the second coil in such a direction as to create a ﬂux opposing the main ﬂux established by i1 . That is, when the switch is closed in Fig. 14-5, ﬂux 2 will have the direction shown. The right-hand rule, with the thumb pointing in the direction of 2 , provides the direction of the natural current i2 . The induced voltage is the driving voltage for the second circuit, as suggested in Fig. 14-6; this voltage is present whether or not the circuit is closed. When the switch is closed, current i2 is established, with a positive direction as shown.

Fig. 14-5

EXAMPLE 14.2 Suppose the switch in the passive loop to be closed at an instant ðt ¼ 0Þ when i1 ¼ 0. the sequence of the passive loop is (see Fig. 14-6).

R2 i2 þ L2

di2 di M 1 ¼0 dt dt

Fig. 14-6

For t > 0,

338

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

while that of the active loop is R1 i1 þ L1

di1 di M 2 ¼ v1 dt dt

Writing the above equations in the s-domain with the initial conditions i1 ð0þ Þ ¼ i2 ð0þ Þ ¼ 0 and eliminating I1 ðsÞ, we ﬁnd HðsÞ

response I ðsÞ Ms ¼ ¼ 2 excitation V1 ðsÞ ðL1 L2 M 2 Þs2 þ ðR1 L2 þ R2 L1 Þs þ R1 R2

and from the poles of HðsÞ we have the natural frequencies of i2 .

14.4

DOT RULE

The sign on a voltage of mutual inductance can be determined if the winding sense is shown on the circuit diagram, as in Figs. 14-4 and 14-5. To simplify the problem of obtaining the correct sign, the coils are marked with dots at the terminals which are instantaneously of the same polarity. To assign the dots to a pair of coupled coils, select a current direction in one coil and place a dot at the terminal where this current enters the winding. Determine the corresponding ﬂux by application of the right-hand rule [see Fig. 14-7(a)]. The ﬂux of the other winding, according to Lenz’s law, opposes the ﬁrst ﬂux. Use the right-hand rule to ﬁnd the natural current direction corresponding to this second ﬂux [see Fig. 14-7(b)]. Now place a dot at the terminal of the second winding where the natural current leaves the winding. This terminal is positive simultaneously with the terminal of the ﬁrst coil where the initial current entered. With the instantaneous polarity of the coupled coils given by the dots, the pictorial representation of the core with its winding sense is no longer needed, and the coupled coils may be illustrated as in Fig. 14-7(c). The following dot rule may now be used: (1)

when the assumed currents both enter or both leave a pair of coupled coils by the dotted terminals, the signs on the M-terms will be the same as the signs on the L-terms; but

(2)

if one current enters by a dotted terminal while the other leaves by a dotted terminal, the signs on the M-terms will be opposite to the signs on the L-terms.

Fig. 14-7 EXAMPLE 14.3 The current directions chosen in Fig. 14-8(a) are such that the signs on the M-terms are opposite to the signs on the L-terms and the dots indicate the terminals with the same instantaneous polarity. Compare this to the conductively coupled circuit of Fig. 14-8(b), in which the two mesh currents pass through the common element in opposite directions, and in which the polarity markings are the same as the dots in the magnetically coupled circuit. The similarity becomes more apparent when we allow the shading to suggest two black boxes.

14.5

ENERGY IN A PAIR OF COUPLED COILS

The energy stored in a single inductor L carrying current i is 0.5Li2 J. of coupled coils is given by

The energy stored in a pair

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

339

Fig. 14-8

1 1 W ¼ L1 i12 þ L2 i22 þ Mi1 i2 2 2

ðJÞ

ð9Þ

where L1 and L2 are the inductances of the two coils and M is their mutual inductance. The term Mi1 i2 in (9) represents the energy due to the eﬀect of the mutual inductance. The sign of this term is (a) positive if both currents i1 and i2 enter either at the dotted or undotted terminals, or (b) negative if one of the currents enters at the dotted terminal and the other enters the undotted end. EXAMPLE 14.4 In a pair of coils, with L1 ¼ 0:1 H and L2 ¼ 0:2 H, at a certain moment, i1 ¼ 4 A and pﬃﬃﬃ i2 ¼ 10 A.pﬃﬃFind the total energy in the coils if the coupling coeﬃcient M is (a) 0.1 H, (b) 2=10 H, (c) 0:1 H, ﬃ and (d) 2=10 H. From (9), ðaÞ

W ¼ ð0:5Þð0:1Þ42 þ ð0:5Þð0:2Þ102 þ ð0:1Þð10Þð4Þ ¼ 14:8 J

ðbÞ ðcÞ ðdÞ

W ¼ 16:46 J W ¼ 6:8 J W ¼ 5:14 J

The maximum and minimum pﬃﬃﬃ energies occur in conjunction with perfect positive coupling ðM ¼ negative coupling ðM ¼ 2=10Þ.

14.6

pﬃﬃﬃ 2=10Þ and perfect

CONDUCTIVELY COUPLED EQUIVALENT CIRCUITS

From the mesh current equations written for magnetically coupled coils, a conductively coupled equivalent circuit can be constructed. Consider the sinusoidal steady-state circuit of Fig. 14-9(a), with the mesh currents as shown. The corresponding equations in matrix form are R1 þ j!L1 j!M I1 V1 ¼ j!M R2 þ j!L2 I2 0 In Fig. 14-9(b), an inductive reactance, XM ¼ !M, carries the two mesh currents in opposite directions, whence

Fig. 14-9

340

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Z12 ¼ Z21 ¼ j!M in the Z-matrix. If now an inductance L1 M is placed in the ﬁrst loop, the mesh current equation for this loop will be ðR1 þ j!L1 ÞI1 j!MI2 ¼ V1 Similarly, L2 M in the second loop results in the same mesh current equation as for the coupled-coil circuit. Thus, the two circuits are equivalent. The dot rule is not needed in the conductively coupled circuit, and familiar circuit techniques can be applied.

14.7

LINEAR TRANSFORMER

A transformer is a device for introducing mutual coupling between two or more electric circuits. The term iron-core transformer identiﬁes the coupled coils which are wound on a magnetic core of laminated specialty steel to conﬁne the ﬂux and maximize the coupling. Air-core transformers are found in electronic and communications applications. A third group consists of coils wound over one another on a nonmetallic form, with a movable slug of magnetic material within the center for varying the coupling. Attention here is directed to iron-core transformers where the permeability of the iron is assumed to be constant over the operating range of voltage and current. The development is restricted to twowinding transformers, although three and more windings on the same core are not uncommon. In Fig. 14-10, the primary winding, of N1 turns, is connected to the source voltage V1 , and the secondary winding, of N2 turns, is connected to the load impedance ZL . The coil resistances are shown by lumped parameters R1 and R2 . Natural current I2 produces ﬂux 2 ¼ 21 þ 22 , while I1 produces 1 ¼ 12 þ 11 . In terms of the coupling coeﬃcient k, 11 ¼ ð1 kÞ1

22 ¼ ð1 kÞ2

Fig. 14-10

From these ﬂux relationships, leakage inductances can be related to the self-inductances: L11 ð1 kÞL1

L22 ð1 kÞL2

The corresponding leakage reactances are: X11 ð1 kÞX1

X22 ð1 kÞX2

It can be shown that the inductance L of an N-turn coil is proportional to N 2 . wound on the same core,

Hence, for two coils

2 L1 N1 ¼ L2 N2 The ﬂux common to both windings in Fig. 14-10 is the mutual ﬂux, m ¼ 12 21 . induces the coil emfs by Faraday’s law,

ð10Þ This ﬂux

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

e1 ¼ N 1

dm dt

e2 ¼ N 2

341

dm dt

Deﬁning the turns ratio, a N1 =N2 , we obtain from these the basic equation of the linear transformer: e1 ¼a ð11Þ e2 In the frequency domain, E1 =E2 ¼ a. The relationship between the mutual ﬂux and the mutual inductance can be developed by analysis of the secondary induced emf, as follows: e2 ¼ N2

dm d12 d21 d12 dðk2 Þ ¼ N2 N2 ¼ N2 N2 dt dt dt dt dt

By use of (6) and (5a), this may be rewritten as e2 ¼ M

di1 di di M di2 kL2 2 ¼ M 1 a dt dt dt dt

where the last step involved (8) and (10): qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ M ¼ k ða2 L2 ÞðL2 Þ ¼ kaL2 Now, deﬁning the magnetizing current i by the equation i1 ¼

i2 þ i a

or

I1 ¼

I2 þ I a

ð12Þ

di dt

or

E2 ¼ jXM I

ð13Þ

we have e2 ¼ M

According to (13), the magnetizing current may be considered to set up the mutual ﬂux m in the core. In terms of coil emfs and leakage reactances, an equivalent circuit for the linear transformer may be drawn, in which the primary and secondary are eﬀectively decoupled. This is shown in Fig. 14-11(a); for comparison, the dotted equivalent circuit is shown in Fig. 14-11(b).

Fig. 14-11 EXAMPLE 14.5 Draw the voltage-current phasor diagram corresponding to Fig. 14-11(a), and from it derive the input impedance of the transformer. The diagram is given in Fig. 14-12, in which L denotes the phase angle of ZL . Note that, in accordance with (13), the induced emfs E1 and E2 lead the magnetizing current I by 908. The diagram yields the three phasor equations V1 ¼ ajXM I þ ðR1 þ jX11 ÞI1 jXM I ¼ ðZL þ R2 þ jX22 ÞI2 1 I1 ¼ I2 þ I a

342

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-12 Elimination of I2 and I among these equations results in V1 ð jXM =aÞðR2 þ jX22 þ ZL Þ Zin ¼ ðR1 þ jX11 Þ þ a2 I1 ð jXM =aÞ þ ðR2 þ jX22 þ ZL Þ

ð14aÞ

If, instead, the mesh current equations for Fig. 14-11(b) are used to derive Zin , the result is Zin ¼ R1 þ jX1 þ

2 XM R2 þ jX2 þ ZL

ð14bÞ

The reader may verify the equivalence of (14a) and (14b)—see Problem 14.36.

14.8

IDEAL TRANSFORMER

An ideal transformer is a hypothetical transformer in which there are no losses and the core has inﬁnite permeability, resulting in perfect coupling with no leakage ﬂux. In large power transformers the losses are so small relative to the power transferred that the relationships obtained from the ideal transformer can be very useful in engineering applications. Referring to Fig. 14-13, the lossless condition is expressed by 1 2 V 1 I1

(see Section 10.7).

¼ 12 V2 I2

But V1 ¼ E1 ¼ aE2 ¼ aV2

and so, a being real, V1 I2 ¼ ¼a V2 I1

ð15Þ

The input impedance is readily obtained from relations (15): Zin ¼

V1 aV2 V ¼ a2 2 ¼ a2 Z L ¼ I1 I2 =a I2

Fig. 14-13

ð16Þ

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

343

EXAMPLE 14.6 The ideal transformer may be considered as the limiting case of the linear transformer of Section 14.7. Thus, in (14a) set R1 ¼ R2 ¼ X11 ¼ X22 ¼ 0 (no losses) and then let XM ! 1 (inﬁnite core permeability), to obtain ð jXM =aÞðZL Þ Zin ¼ lim a2 ¼ a2 ZL XM !1 ð jXM =aÞ þ ZL in agreement with (16)

Ampere-Turn Dot Rule Since a ¼ N1 =N2 in (15), N1 I1 ¼ N2 I2 that is, the ampere turns of the primary equal the ampere turns of the secondary. A rule can be formulated which extends this result to transformers having more than two windings. A positive sign is applied to an ampere-turn product if the current enters the winding by the dotted terminal; a negative sign is applied if the current leaves by the dotted terminal. The ampere-turn dot rule then states that the algebraic sum of the ampere-turns for a transformer is zero. EXAMPLE 14.7 The three-winding transformer shown in Fig. 14-14 has turns N1 ¼ 20, N2 ¼ N3 ¼ 10. given that I2 ¼ 10:0 53:138 A, I3 ¼ 10:0 458 A. With the dots and current directions as shown on the diagram,

Find I1

Fig. 14-14 N1 I1 N2 I2 N3 I3 ¼ 0 from which 20I1 ¼ 10ð10:0 53:138Þ þ 10ð10:0 458Þ I1 ¼ 6:54 j7:54 ¼ 9:98 49:068 A

14.9

AUTOTRANSFORMER

An autotransformer is an electrically continuous winding, with one or more taps, on a magnetic core. One circuit is connected to the end terminals, while the other is connected to one end terminal and to a tap, part way along the winding. Referring to Fig. 14-15(a), the transformation ratio is V1 N1 þ N2 ¼ aþ1 V2 N2 which exceeds by unity the transformation ratio of an ideal two-winding transformer having the same turns ratio. Current I1 through the upper or series part of the winding, of N1 turns, produces the ﬂux 1 . By Lenz’s law the natural current in the lower part of the winding produces an opposing ﬂux

344

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-15

2 . Therefore, current In leaves the lower winding by the tap. The dots on the winding are as shown in Fig. 14-15(b). In an ideal autotransformer, as in an ideal transformer, the input and output complex powers must be equal. 1 2 V1 I1

¼ 12 V1 Iab ¼ 12 V2 IL IL ¼aþ1 Iab

whence

That is, the currents also are in the transformation ratio. Since IL ¼ Iab þ Icb , the output complex power consists of two parts: 1 2 V2 IL

¼ 12 V2 Iab þ 12 V2 Icb ¼ 12 V2 Iab þ að12 V2 Iab Þ

The ﬁrst term on the right is attributed to conduction; the second to induction. Thus, there exist both conductive and magnetic coupling between source and load in an autotransformer.

14.10

REFLECTED IMPEDANCE

A load Z2 connected to the secondary port of a transformer, as shown in Fig. 14-16, contributes to its input impedance. This contribution is called reﬂected impedance. Using the terminal characteristics of the coupled coils and applying KVL around the secondary loop, we ﬁnd V1 ¼ L1 sI1 þ MsI2 0 ¼ MsI1 þ L2 sI2 þ Z2 I2 By eliminating I2 , we get

Fig. 14-16

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

Z1 ¼

V1 M 2 s2 ¼ L1 s I1 Z2 þ L2 s

345

ð17Þ

For the ac steady state where s ¼ j!, we have Z1 ¼ j!L1 þ

M 2 !2 Z2 þ j!L2

ð18Þ

The reﬂected impedance is Zreflected ¼

M 2 !2 Z2 þ j!L2

ð19Þ

The load Z2 is seen by the source as M 2 !2 =ðZ2 þ j!L2 Þ. The technique is often used to change an impedance to a certain value; for example, to match a load to a source. EXAMPLE 14.8 Given L1 ¼ 0:2 H, L2 ¼ 0:1 H, M ¼ 0:1 H, and R ¼ 10 in the circuit of Fig. 14-17. for v1 ¼ 142:3 sin 100t.

Find i1

Fig. 14-17 The input impedance Z1 at ! ¼ 100 is [see (18)] Z1 ¼

pﬃﬃﬃﬃﬃ V1 M 2 !2 0:01ð10 000Þ ¼ j!L1 þ ¼ j20 þ ¼ 5 þ j15 ¼ 5 10 71:68 I1 Z2 þ j!L2 10 þ j10

Then,

I1 ¼ V1 =Z1 ¼ 9 71:68 A

or

i1 ¼ 9 sin ð100t 71:68Þ

EXAMPLE 14.9 Referring to Example 14.8, let v1 ¼ uðtÞ. The input impedance is [see (17)] Z1 ðsÞ ¼ L1 s

ðAÞ

Find i1;f , the forced response. M 2 s2 R þ L2 s

Substituting the given values for the elements, we get Z1 ðsÞ ¼

sðs þ 200Þ 10ðs þ 100Þ

or

Y1 ðsÞ ¼

10ðs þ 100Þ sðs þ 200Þ

For t > 0, the input v1 ¼ 1 V is an exponential est whose exponent s ¼ 0 is a pole of Y1 ðsÞ. Therefore, i1;f ¼ kt with k ¼ 1=L1 ¼ 5. This result may also be obtained directly by dc analysis of the circuit in Fig. 14-17.

Solved Problems 14.1

When one coil of a magnetically coupled pair has a current 5.0 A the resulting ﬂuxes 11 and 12 are 0.2 mWb and 0.4 mWb, respectively. If the turns are N1 ¼ 500 and N2 ¼ 1500, ﬁnd L1 , L2 , M, and the coeﬃcient of coupling k.

346

MUTUAL INDUCTANCE AND TRANSFORMERS

1 ¼ 11 þ 12 ¼ 0:6 mWb M¼

L1 ¼

N1 1 500ð0:6Þ ¼ 60 mH ¼ 5:0 I1

N2 12 1500ð0:4Þ ¼ 120 mH ¼ 5:0 I1

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Then, from M ¼ k L1 L2 , L2 ¼ 540 mH.

14.2

[CHAP. 14

k¼

12 ¼ 0:667 1

Two coupled coils have self-inductances L1 ¼ 50 mH and L2 ¼ 200 mH, and a coeﬃcient of coupling k ¼ 0:50. If coil 2 has 1000 turns, and i1 ¼ 5:0 sin 400t (A), ﬁnd the voltage at coil 2 and the ﬂux 1 . pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ M ¼ k L1 L2 ¼ 0:50 ð50Þð200Þ ¼ 50 mH di d ð5:0 sin 400tÞ ¼ 100 cos 400t v2 ¼ M 1 ¼ 0:05 dt dt

ðVÞ

Assuming, as always, a linear magnetic circuit, M¼

14.3

N2 12 N2 ðk1 Þ ¼ i1 i1

or

1 ¼

M i ¼ 5:0 104 sin 400t N2 k 1

ðWbÞ

Apply KVL to the series circuit of Fig. 14-18.

Fig. 14-18 Examination of the winding sense shows that the signs of the M-terms are opposite to the signs on the L-terms. ð di di 1 di di i dt þ L2 M ¼ v Ri þ L1 M þ dt dt C dt dt ð di 1 or i dt ¼ v Ri þ L 0 þ dt C where L 0 L1 þ L2 2M.

Because M

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ L1 þ L2 L1 L2 2

L 0 is nonnegative.

14.4

In a series aiding connection, two coupled coils have an equivalent inductance LA ; in a series opposing connection, LB . Obtain an expression for M in terms of LA and LB . As in Problem 14.3, L1 þ L2 þ 2M ¼ LA which give

L1 þ L2 2M ¼ LB

CHAP. 14]

347

MUTUAL INDUCTANCE AND TRANSFORMERS

1 M ¼ ðLA LB Þ 4 This problem suggests a method by which M can be determined experimentally.

14.5

(a) Write the mesh current equations for the coupled coils with currents i1 and i2 shown in Fig. 14-19. (b) Repeat for i2 as indicated by the dashed arrow.

Fig. 14-19 (a) The winding sense and selected directions result in signs on the M-terms as follows: di1 þM dt di R2 i2 þ L2 2 þ M dt

di2 ¼v dt di1 ¼v dt d ði i2 Þ þ M R1 ði1 i2 Þ þ L1 dt 1 di d d ði i1 Þ þ L1 ði i1 Þ M R1 ði2 i1 Þ þ R2 i2 þ L2 2 M dt 2 dt 2 dt R1 i1 þ L1

ðbÞ

14.6

di2 ¼v dt di2 ¼0 dt

Obtain the dotted equivalent circuit for the coupled circuit shown in Fig. 14-20, and use it to ﬁnd the voltage V across the 10- capacitive reactance.

Fig. 14-20 To place the dots on the circuit, consider only the coils and their winding sense. Drive a current into the top of the left coil and place a dot at this terminal. The corresponding ﬂux is upward. By Lenz’s law, the ﬂux at the right coil must be upward-directed to oppose the ﬁrst ﬂux. Then the natural current leaves this winding by the upper terminal, which is marked with a dot. See Fig. 14-21 for the complete dotted equivalent circuit, with currents I1 and I2 chosen for calculation of V.

348

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-21

5 j5

5 þ j3

5 þ j3

10 þ j6

I1 I2

"

¼

I1 ¼

10 08 10 j10

#

10 10 j10 Z

5 þ j3 10 þ j6

¼ 1:015 113:968 A

and V ¼ I1 ðj10Þ ¼ 10:15 23:968 V.

14.7

Obtain the dotted equivalent for the circuit shown in Fig. 14-22 and use the equivalent to ﬁnd the equivalent inductive reactance.

Fig. 14-22 Drive a current into the ﬁrst coil and place a dot where this current enters. The natural current in both of the other windings establishes an opposing ﬂux to that set up by the driven current. Place dots where the natural current leaves the windings. (Some confusion is eliminated if the series connections are ignored while determining the locations of the dots.) The result is Fig. 14-23. Z ¼ j3 þ j5 þ j6 2ð j2Þ þ 2ð j4Þ 2ð j3Þ ¼ j12 that is, an inductive reactance of 12 .

Fig. 14-23

14.8

(a) Compute the voltage V for the coupled circuit shown in Fig. 14-24. polarity of one coil reversed.

(b) Repeat with the

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

349

Fig. 14-24 pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ (a) XM ¼ ð0:8Þ 5ð10Þ ¼ 5:66 , and so the Z-matrix is 3 þ j1 3 j1:66 ½Z ¼ 3 j1:66 8 þ j6 3 þ j1 50 3 j1:66 0 ¼ 8:62 24:798 A I2 ¼ Z

Then,

and V ¼ I2 ð5Þ ¼ 43:1 24:798 V. ½Z ¼ ðbÞ

3 þ j1 3 þ j9:66 3 þ j9:66 8 þ j6

3 þ j1 50 3 þ j9:66 0 ¼ 3:82 112:128 A I2 ¼ Z and V ¼ 12 ð5Þ ¼ 19:1 112:128 V.

14.9

Obtain the equivalent inductance of the parallel-connected, coupled coils shown in Fig. 14-25. Currents I1 and I2 are selected as shown on the diagram; then Zin ¼ V1 =I1 : j!0:3 j!0:043 ½Z ¼ j!0:043 j!0:414 and

Zin ¼

Z ð j!0:3Þð j!0:414Þ ð j!0:043Þ2 ¼ ¼ j!0:296 11 j!0:414

or Leq is 0.296 H.

Fig. 14-25

14.10 For the coupled circuit shown in Fig. 14-26, show that dots are not needed so long as the second loop is passive.

350

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-26 Currents I1 and I2 are selected as shown. 50 j4 0 5 þ j10 250 þ j500 ¼ ¼ 10:96 54:648 A I1 ¼ 2 þ j5 24 þ j45 j4 j4 5 þ j10 2 þ j5 50 j4 0 ¼ 3:92 118:07 908 A I2 ¼ Z The value of Z is unaﬀected by the sign on M. Since the numerator determinant for I1 does not involve the coupling impedance, I1 is also unaﬀected. The expression for I2 shows that a change in the coupling polarity results in a 1808 phase shift. With no other phasor voltage present in the second loop, this change in phase is of no consequence.

14.11 For the coupled circuit shown in Fig. 14-27, ﬁnd the ratio V2 =V1 which results in zero current I1 .

I1 ¼ 0 ¼

V1 V2

j2 2 þ j2 Z

Then, V1 ð2 þ j2Þ V2 ð j2Þ ¼ 0, from which V2 =V1 ¼ 1 j1.

Fig. 14-27

14.12 In the circuit of Fig. 14-28, ﬁnd the voltage across the 5 reactance with the polarity shown. For the choice of mesh currents shown on the diagram, 50 458 j8 0 j3 150 458 ¼ ¼ 1:37 40:288 A I1 ¼ 109 j9 3 þ j15 j8 j8 j3 Similarly, I2 ¼ 3:66 40:288 A.

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

351

Fig. 14-28 The voltage across the j5 is partly conductive, from the currents I1 and I2 , and partly mutual, from current I1 in the 4 reactance. V ¼ ðI1 þ I2 Þð j5Þ þ I1 ð j3Þ ¼ 29:27 49:728 V Of course, the same voltage must exist across the capacitor: V ¼ I2 ðj8Þ ¼ 29:27 49:728 V

14.13 Obtain The´venin and Norton equivalent circuits at terminals ab for the coupled circuit shown in Fig. 14-29. In open circuit, a single clockwise loop current I is driven by the voltage source. I¼

10 08 ¼ 1:17 20:568 A 8 þ j3

Fig. 14-29 Then V 0 ¼ Ið j5 þ 4Þ Ið j6Þ ¼ 4:82 34:608 V. To ﬁnd the short-circuit current I 0 , two clockwise mesh currents are assumed, with I2 ¼ I 0 . 8 þ j3 10 4 þ j1 0 ¼ 0:559 83:398 A I0 ¼ 8 þ j3 4 þ j1 4 þ j1 7 þ j5

and

Z0 ¼

V0 4:82 34:608 ¼ 8:62 48:798 ¼ I0 0:559 83:398

The equivalent circuits are pictured in Fig. 14-30.

14.14 Obtain a conductively coupled equivalent circuit for the magnetically coupled circuit shown in Fig. 14-31. Select mesh currents I1 and I2 as shown on the diagram and write the KVL equations in matrix form.

352

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-30

Fig. 14-31

3 þ j1 3 j2 3 j2 8 þ j6

I1 I2

¼

50 08 0

The impedances in Fig. 14-32 are selected to give the identical Z-matrix. Thus, since I1 and I2 pass through the common impedance, Zb , in opposite directions, Z12 in the matrix is Zb . Then, Zb ¼ 3 þ j2 . Since Z11 is to include all impedances through which I1 passes, 3 þ j1 ¼ Za þ ð3 þ j2Þ from which Za ¼ j1 .

Similarly, Z22 ¼ 8 þ j6 ¼ Zb þ Zc

and Zc ¼ 5 þ j4

.

Fig. 14-32

14.15 For the transformer circuit of Fig. 14-11(b), k ¼ 0:96, R1 ¼ 1:2 , R2 ¼ 0:3 , X1 ¼ 20 , X2 ¼ 5 , ZL ¼ 5:0 36:878 , and V2 ¼ 100 08 V. Obtain the coil emfs E1 and E2 , and the magnetizing current I . X11 ¼ ð1 kÞX1 ¼ ð1 0:96Þð20Þ ¼ 0:8 X22 ¼ ð1 kÞX2 ¼ 0:2 sﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ X1 ¼2 XM ¼ k X1 X2 ¼ 9:6 a¼ X2

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

353

Now a circuit of the form Fig. 14-11(a) can be constructed, starting from the phasor voltage-current relationship at the load, and working back through E2 to E1 . V2 100 08 ¼ 20 36:878 A ¼ ZL 5:0 36:878 E2 ¼ I2 ðR2 þ jX22 Þ þ V2 ¼ ð20 36:878Þð0:3 þ j0:2Þ þ 100 08 ¼ 107:2 j0:4 V I2 ¼

E1 ¼ aE2 ¼ 214:4 j0:8 V E I ¼ 2 ¼ 0:042 j11:17 A jXM

14.16 For the linear transformer of Problem 14.15, calculate the input impedance at the terminals where V1 is applied. Method 1 Completing the construction begun in Problem 14.15, 1 I ¼ ð0:042 j11:17Þ þ 10 36:878 ¼ 18:93 65:138 A a 2 V1 ¼ I1 ðR1 þ jX11 Þ þ E1 ¼ ð18:93 65:138Þð1:2 þ j0:8Þ þ ð214:4 j0:8Þ I1 ¼ I þ

¼ 238:2 3:628 V Therefore, Zin ¼

V1 238:2 3:628 ¼ 12:58 61:518 ¼ I1 18:93 65:138

Method 2 By (14a) of Example 14.5, Zin ¼ ð1:2 þ j0:8Þ þ 22 ¼

ð j4:8Þð0:3 þ j0:2 þ 5:0 36:878Þ 0:3 þ j5:0 þ 5:0 36:878

114:3 123:258 ¼ 12:58 61:508 9:082 61:758

Method 3 By (14b) of Example 14.5, ð9:6Þ2 0:3 þ j5 þ 5:0 36:878 ¼ ð1:2 þ j20Þ þ ð4:80 j8:94Þ ¼ 12:58 61:538

Zin ¼ ð1:2 þ j20Þ þ

14.17 In Fig. 14-33, three identical transformers are primary wye-connected and secondary delta-connected. A single load impedance carries current IL ¼ 30 08 A. Given Ib2 ¼ 20 08 A

Ia2 ¼ Ic2 ¼ 10 08 A

and N1 ¼ 10N2 ¼ 100, ﬁnd the primary currents Ia1 , Ib1 , Ic1 . The ampere-turn dot rule is applied to each transformer. N1 Ia1 þ N2 Ia2 ¼ 0

or

N1 Ib1 N2 Ib2 ¼ 0

or

N1 Ic1 þ N2 Ic2 ¼ 0

or

10 ð10 08Þ ¼ 1 08 A 100 10 Ib1 ¼ ð20 08Þ ¼ 2 08 A 100 10 Ic1 ¼ ð10 08Þ ¼ 1 08 A 100 Ia1 ¼

354

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-33 The sum of the primary currents provides a check: Ia1 þ Ib1 þ Ic1 ¼ 0

14.18 For the ideal autotransformer shown in Fig. 14-34, ﬁnd V2 , Icb , and the input current I1 . a

N1 1 ¼ N2 2

V1 ¼ 100 08 V aþ1

IL ¼

Icb ¼ IL Iab ¼ 3:33 608 A

Iab

V2 ¼

V2 ¼ 10 608 A ZL I ¼ L ¼ 6:67 608 A aþ1

Fig. 14-34

14.19 In Problem 14.18, ﬁnd the apparent power delivered to the load by transformer action and that supplied by conduction. Scond ¼ 12 V2 Iab ¼ 12 ð100 08Þð6:67 608Þ ¼ 333 608 VA Strans ¼ aScond ¼ 167 608 VA

CHAP. 14]

355

MUTUAL INDUCTANCE AND TRANSFORMERS

14.20 In the coupled circuit p ofﬃﬃﬃ Fig. 14-35, ﬁnd the input admittance Y1 ¼ I1 =V1 and determine the current i1 ðtÞ for v1 ¼ 2 2 cos t.

Fig. 14-35 Apply KVL around loops 1 and 2 in the s-domain. V1 ¼ sI1 þ sI2 þ

I1 I2 s

0 ¼ sI1 þ ð2s þ 1ÞI2 þ

I2 I1 s

Eliminating I2 in these equations results in I1 2s2 þ s þ 1 ¼ 3 V1 s þ s2 þ 5s þ 1 pﬃﬃﬃ For s ¼ j, the input admittance is Y1 ¼ ð1 þ jÞ=4 ¼ 2=4 458. Therefore, i1 ðtÞ ¼ cos ðt þ 458Þ. Y1 ¼

14.21 Find the input impedance Z1 ¼ V1 =I1 in the coupled circuit of Fig. 14-36.

Fig. 14-36 Apply KVL around loops 1 and 2 in the s-domain. ( V1 ¼ sI1 þ 13 sI2 þ 2ðI1 þ I2 Þ 1 0 ¼ 13 sI1 þ 14 sI2 þ 2ðI1 þ I2 Þ þ 12 sI2 ( or

V1 ¼ ð2 þ sÞI1 þ ð2 þ 13 sÞI2 0 ¼ ð2 þ 13 sÞI1 þ ð2 þ 13 sÞI2

The result is I2 ¼ I1

and

Z1 ¼

V1 2 ¼ s I1 3

The current through the resistor is I1 þ I2 ¼ 0 and the resistor has no eﬀect on Z1 . purely inductive.

The input impedance is

356

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Supplementary Problems 14.22

Two coupled coils, L1 ¼ 0:8 H and L2 ¼ 0:2 H, have a coeﬃcient of coupling k ¼ 0:90. inductance M and the turns ratio N1 =N2 . Ans: 0:36 H, 2

14.23

Two coupled coils, N1 ¼ 100 and N2 ¼ 800, have a coupling coeﬃcient k ¼ 0:85. current of 5.0 A in coil 2, the ﬂux is 2 ¼ 0:35 mWb. Find L1 , L2 , and M. Ans: 0:875 mH, 56 mH, 5.95 mH

14.24

Two identical coupled coils have an equivalent inductance of 80 mH when connected series aiding, and 35 mH in series opposing. Find L1 , L2 , M, and k. Ans: 28:8 mH, 28.8 mH, 11.25 mH, 0.392

14.25

Two coupled coils, with L1 ¼ 20 mH, L2 ¼ 10 mH, and k ¼ 0:50, are connected four diﬀerent ways: series aiding, series opposing, and parallel with both arrangements of winding sense. Obtain the equivalent inductances of the four connections. Ans: 44:1 mH, 15.9 mH, 9.47 mH, 3.39 mH

14.26

Write the mesh current equations for the coupled circuit shown in Fig. 14-37. circuit and write the same equations. Ans:

di1 þ R 3 i2 þ M dt di ðR2 þ R3 Þi2 þ L2 2 þ R3 i1 þ M dt

ðR1 þ R3 Þi1 þ L1

Find the mutual

With coil 1 open and a

Obtain the dotted equivalent

di2 ¼v dt di1 ¼v dt

Fig. 14-37 14.27

Write the phasor equation for the single-loop, coupled circuit shown in Fig. 14-38. Ans: ð j5 þ j3 j5:03 j8 þ 10ÞI ¼ 50 08

14.28

Obtain the dotted equivalent circuit for the coupled circuit of Fig. 14-38.

14.29

The three coupled coils shown in Fig. 14-40 have coupling coeﬃcients of 0.50. inductance between the terminals AB. Ans: 239 mH

14.30

Obtain two forms of the dotted equivalent circuit for the coupled coils shown in Fig. 14-40. Ans: See Fig. 14-41.

14.31

(a) Obtain the equivalent impedance at terminals AB of the coupled circuit shown in Fig. 14-42. Reverse the winding sense of one coil and repeat. Ans: ðaÞ 3:40 41:668 ; ðbÞ 2:54 5:378

Ans:

See Fig. 14-39. Obtain the equivalent

(b)

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

357

Fig. 14-38

Fig. 14-39

Fig. 14-40

Fig. 14-41 14.32

In the coupled circuit shown in Fig. 14-43, ﬁnd V2 for which I1 ¼ 0. What voltage appears at the 8 inductive reactance under this condition? Ans: 141:4 458 V; 100 08 V (+ at dot)

14.33

Find the mutual reactance XM for the coupled circuit of Fig. 14-44, if the average power in the 5- resistor is 45.24 W. Ans: 4

358

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Fig. 14-42

Fig. 14-43

Fig. 14-44 14.34

For the coupled circuit shown in Fig. 14-45, ﬁnd the components of the current I2 resulting from each source V1 and V2 . Ans: 0:77 112:68 A; 1:72 86:058 A

Fig. 14-45 14.35

Determine the coupling coeﬃcient k in the circuit shown in Fig. 14-46, if the power in the 10- resistor is 32 W. Ans: 0:791

14.36

In (14a), replace a, X11 , X22 , and XM by their expressions in terms of X1 , X2 , and k, thereby obtaining (14b).

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

Fig. 14-46 14.37

For the coupled circuit shown in Fig. 14-47, ﬁnd the input impedance at terminals ab. Ans: 3 þ j36:3

Fig. 14-47 14.38

Find the input impedance at terminals ab of the coupled circuit shown in Fig. 14-48. Ans: 1 þ j1:5

Fig. 14-48 14.39

Find the input impedance at terminals ab of the coupled circuit shown in Fig. 14-49. Ans: 6:22 þ j4:65

Fig. 14-49

359

360

14.40

MUTUAL INDUCTANCE AND TRANSFORMERS

[CHAP. 14

Obtain The´venin and Norton equivalent circuits at terminals ab of the coupled circuit shown in Fig. 14-50. Ans: V 0 ¼ 7:07 458 V; I 0 ¼ 1:04 27:98 A; Z 0 ¼ 6:80 72:98

Fig. 14-50

14.41

For the ideal transformer shown in Fig. 14-51, ﬁnd I1 , given IL1 ¼ 10:0 08 A Ans:

IL2 ¼ 10:0 36:878 A

IL3 ¼ 4:47 26:578 A

16:5 14:048 A

Fig. 14-51

14.42

When the secondary of the linear transformer shown in Fig. 14-52 is open-circulated, the primary current is I1 ¼ 4:0 89:698 A. Find the coeﬃcient of coupling k. Ans: 0:983

Fig. 14-52 14.43

For the ideal transformer shown in Fig. 14-53, ﬁnd I1 , given I2 ¼ 50 36:878 A and I3 ¼ 16 08 A. Ans: 26:6 34:298 A

14.44

Considering the autotransformer shown in Fig. 14-54 ideal, obtain the currents I1 , Icb , and Idc . Ans: 3:70 22:58 A; 2:12 86:718 A; 10:34 11:838 A

CHAP. 14]

MUTUAL INDUCTANCE AND TRANSFORMERS

Fig. 14-53

Fig. 14-54

361

Circuit Analysis Using Spice and PSpice 15.1

SPICE AND PSPICE

Spice (Simulation Program with Integrated Circuit Emphasis) is a computer program developed in the 1970s at the University of California at Berkeley for simulating electronic circuits. It is used as a tool for analysis, design, and testing of integrated circuits as well as a wide range of other electronic and electrical circuits. Spice is a public domain program. Commercial versions, such as PSpice by MicroSim Corporation, use the same algorithm and syntax as Spice but provide the technical support and addons that industrial customers need. This chapter introduces the basic elements of Spice/PSpice and their application to some simple circuits. Examples are run on the evaluation version of PSpice which is available free of charge.

15.2

CIRCUIT DESCRIPTION

The circuit description is entered in the computer in the form of a series of statements in a text ﬁle prepared by any ASCII text editor and called the source ﬁle. It may also be entered graphically by constructing the circuit on the computer monitor with the Schematic Capture program from MicroSim. In this chapter, we use the source ﬁle with the generic name SOURCE.CIR. To solve the circuit, we run the circuit solver on the source ﬁle. The computer puts the solution in a ﬁle named SOURCE.OUT. EXAMPLE 15.1 Use PSpice to ﬁnd the dc steady-state voltage across the 5-mF capacitor in Fig. 15-1(a).

Fig. 15-1

362 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

363

We ﬁrst label the nodes by the numbers 0, 1, 2 and the elements by the symbols R1, R2, C, and Vs [Fig. 15-1(b)]. We then create in ASCII the source ﬁle shown below and give it a name, for instance, EXMP1.CIR. DC analysis, Fig. Vs R1 R2 C .END

15-1 1 0 1 2 0 2 0 2

DC 3k 6k 5 uF

9V

Executing the command PSPICE EXMP1, the computer solves the circuit and writes the following results in the ﬁle EXMP1.OUT. NODE VOLTAGE NODE (1) 9.0000 (2) VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 1:000E 03 TOTAL POWER DISSIPATION

VOLTAGE 6.0000

9:00E 0:3 WATTS

The printed output speciﬁes that the voltage at node 2 with reference to node 0 is 6 V, the current entering the voltage source Vs is 103 A, and the total power dissipated in the circuit is 9 103 W.

15.3

DISSECTING A SPICE SOURCE FILE

The source ﬁle of Example 15.1 is very simple and contains the statements necessary for solving the circuit of Fig. 15-1 by Spice. Each line in the source ﬁle is a statement. In general, if a line is too long (over 80 characters), it can be continued onto subsequent lines. The continuation lines must begin with a plus (þ) sign in the ﬁrst column. PSpice does not diﬀerentiate uppercase and lowercase letters and standard units are implied when not speciﬁed. We will use both notations. Title Statement The ﬁrst line in the source ﬁle of Example 15-1 is called the title statement. This line is used by Spice as a label within the output ﬁle, and it is not considered in the analysis. Therefore, it is mandatory to allocate the ﬁrst line to the title line, even if it is left blank. .END Statement The .END statement is required at the end of the source ﬁle. Any statement following the .END will be considered a separate source ﬁle. Data Statements The remaining four data statements in the source ﬁle of Example 15.1 completely specify the circuit. The second line states that a voltage source named Vs is connected between node 1 (positive end of the source) and the reference node 0. The source is a dc source with a value of 9 V. The third line states that a resistor named R1 , with the value of 3 k , is connected between nodes 1 and 2. Similarly, the fourth and ﬁfth lines specify the connection of R2 (6 k ) and C (5 mF), respectively, between nodes 0 and 2. In any circuit, one node should be numbered 0 to serve as the reference node. The set of data statements describing the topology of the circuit and element values is called the netlist. Data statement syntax is described in Section 15.4. Control and Output Statements In the absence of any additional commands, and only based on the netlist, Spice automatically computes the dc steady state of the following variables: (i) Node voltages with respect to node 0.

364

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

(ii) Currents entering each voltage source. (iii) Power dissipated in the circuit. However, additional control and output statements may be included in the source ﬁle to specify other variables (see Section 15.5).

15.4

DATA STATEMENTS AND DC ANALYSIS

Passive Elements Data statements for R, L, and C elements contain a minimum of three segments. The ﬁrst segment gives the name of the element as a string of characters beginning with R, L, or C for resistors, inductors, or capacitors, respectively. The second segment gives the node numbers, separated by a space, between which the element is connected. The third segment gives the element value in ohms, henrys, and farads, optionally using the scale factors given in Table 15-1. Table 15-1 Scale Factors and Symbols Name

Symbol

femto pico nano micro milli kilo mega giga tera

Value 15

f p n u m k meg g t

10 1012 109 106 103 103 106 109 1012

¼ 1E 15 ¼ 1E 12 ¼ 1E 9 ¼ 1E 6 ¼ 1E 3 ¼ 1E3 ¼ 1E6 ¼ 1E9 ¼ 1E12

Possible initial conditions can be given in the fourth segment using the form IC ¼ xx. The syntax of the data statement is hnamei

hnodesi

hvaluei

½hinitial conditionsi

The brackets indicate optional segments in the statement. EXAMPLE 15.2 Write the data statements for R, L, and C given in Fig. 15-2.

Fig. 15-2 Element Resistor Inductor Capacitor

hnamei Rin L1 Ceq

hnodesi 1 2 5 4 6

hvaluei 3k 30 uH 5 pF

[hinitial conditioni IC ¼ 2 mA IC ¼ 2 V

The third statement for the capacitor connection speciﬁes one node only. The missing node is always taken to be the reference node.

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

365

Independent Sources Independent sources are speciﬁed by hnamei

hnodesi

htypei

hvaluei

The htypei for dc and ac sources is DC and AC, respectively. Other time-dependent sources will be described in Section 15.12. Names of voltage and current sources begin with V and I, respectively. For voltage sources, the ﬁrst node indicates the positive terminal. The current in the current source ﬂows from the ﬁrst node to the second. EXAMPLE 15.3

Write data statements for the sources of Fig. 15-3.

Fig. 15-3

Source Independent Voltage Source Independent Current Source EXAMPLE 15.4

hnamei Vs Ibias

hnodesi 2 1 3 4

htypei hvaluei DC 30 V DC 2A

Write the netlist for the circuit of Fig. 15-4(a) and run PSpice on it for dc analysis.

Fig. 15-4

We ﬁrst number the nodes and name the elements as in Fig. 15-4(b). The netlist is DC Analysis, R1 0 R2 1 R3 2 R4 0 Vs 3 Is 0 .END

Fig. 1 2 3 3 1 2

15-4 500 3k 1k 1.5 k DC DC

4V 3 mA

366

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

The results are writte in the output ﬁle as follows: NODE (1)

VOLTAGE .1250

NODE (2)

VOLTAGE 5.3750

NODE (3)

VOLTAGE 4.1250

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 1:500E 03 TOTAL POWER DISSIPATION

6:00E 03 WATTS

Dependent Sources Linearly dependent sources are speciﬁed by hnamei

hnodesi

hcontroli

hgaini

Each source name should begin with a certain letter according to the following rule: Voltage-controlled voltage source Current-controlled current source Voltage-controlled current source Current-controlled voltage source

Exx Fxx Gxx Hxx

The order of nodes is similar to that of independent sources. For the voltage-controlled sources, hcontroli is the pair of nodes whose voltage diﬀerence controls the source, with the ﬁrst node indicating the þ terminal. The hgaini is the proportionality factor. EXAMPLE 15.5 Write the data statements for the voltage-controlled sources of Fig. 15-5.

Fig. 15-5

Source VCVS VCCS

hnamei E1 G1

hnodesi 4 3 5 6

hcontroli 2 1 2 1

hgaini k1 k2

In the case of current-controlled sources we ﬁrst introduce a zero-valued voltage source (or dummy voltage Vdmy ) on the path of the controlling current and use its name as the control variable. EXAMPLE 15.6 Write data statements for the current-controlled sources in Fig. 15-6. Introduce Vdmy (Vdmy) with current i entering it at node 1. Vdmy

1

7

DC

0

The data statements for the controlled sources are Source CCVS CCCS

hnamei H1 F1

hnodesi 4 3 5 6

hcontroli Vdmy Vdmy

hgaini k3 k4

CHAP. 15]

367

CIRCUIT ANALYSIS USING SPICE AND PSPICE

Fig. 15-6

EXAMPLE 15.7

Write the netlist for the circuit of Fig. 15-7(a) and run PSpice on it for dc analysis.

Fig. 15-7 Number the nodes and name the elements as in Fig. 15-7(b).

Then, the netlist is

DC analysis with dependent source, Fig. 15-7 Vs 1 0 DC 12 R1 1 2 1k R2 0 3 2k R3 0 4 500 Vdmy 2 3 0 F1 4 3 Vdmy 100 .END The results in the output ﬁle are NODE (1)

VOLTAGE 12.0000

NODE (2)

VOLTAGE 11.9410

NODE (3)

7:09E 04

WATTS

VOLTAGE 11.9410

NODE (4)

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 5:911E 05 Vdmy 5:911E 05 TOTAL POWER DISSIPATION

15.5

CONTROL AND OUTPUT STATEMENTS IN DC ANALYSIS Certain statements control actions or the output format.

Examples are:

:OP prints the dc operating point of all independent sources. :DC sweeps the value of an independent dc source. :DC

hnamei

hinitial valuei

hfinal valuesi

The syntax is hstep sizei

VOLTAGE 2:9557

368

CIRCUIT ANALYSIS USING SPICE AND PSPICE

.PRINT prints the value of variables.

[CHAP. 15

The syntax is

:PRINT

houtput variablesi

htypei

htypei is DC, AC, or TRAN (transient). .PLOT line-prints variables.

The syntax is :PLOT

htypei

houtput variablesi

.PROBE generates a data ﬁle *.DAT which can be plotted in post-analysis by evoking the Probe program. The syntax is :PROBE

½houtput variablesi

EXAMPLE 15.8 Find the value of Vs in the circuit in Fig. 15-8 such that the power dissipated in the 1-k resistor is zero. Use the .DC command to sweep Vs from 1 to 6 V in steps of 1 V and use .PRINT to show IðVsÞ, V(1,2), and V(2).

Fig. 15-8

The source ﬁle is DC sweep, Fig. 15-8 Vs 1 0 DC 1V Is 0 2 DC 1 mA R1 1 2 1k R2 0 2 2k .DC Vs 1 6 1 .PRINT DC I(Vs) V(1,2) V(2) .END The results in the output ﬁle are DC TRANSFER CURVES Vs I(Vs) 1:000E þ 00 3:333E 04 2:000E þ 00 1:333E 12 3:000E þ 00 3:333E 04 4:000E þ 00 6:667E 04 5:000E þ 00 1:000E 03 6:000E þ 00 1:333E 03

V(1,2) 3:333E 01 1:333E 09 3:333E 01 6:667E 01 1:000E þ 00 1:333E þ 00

V(2) 1:333E þ 00 2:000E þ 00 2:667E þ 00 3:333E þ 00 4:000E þ 00 4:667E þ 00

The answer is Vs ¼ 2 V. EXAMPLE 15.9 Write the source ﬁle for the circuit in Fig. 15-9(a) using commands .DC, .PLOT, and .PROBE to ﬁnd the I-V characteristic equation for I varying from 0 to 2 A at the terminal AB. First, we connect a dc current source Iadd at terminal AB, ‘‘sweep’’ its value from 0 to 2 A using the .DC command, and plot V versus I. Since the circuit is linear, two points are necessary and suﬃcient. However, for clarity of the plot, ten steps are included in the source ﬁle as follows:

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

Fig. 15-9

Terminal Characteristic, Fig. 15-9 Iadd 0 5 DC Is 0 4 DC Vs 3 2 DC R1 0 1 1 R2 1 2 2 R3 3 4 3 R4 4 5 2 .DC Iadd 0 2 .PLOT DC V(5) .PROBE .END The output is shown in Fig. 15-9(b).

0 0.6 A 5V

0.2

The I-V equation is V ¼ 8I þ 8:6.

369

370

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

15.6 THE´VENIN EQUIVALENT .TF Statement The .TF command provides the transfer function from an input variable to an output variable and produces the resistances seen by the two sources. It can thus generate the The´venin equivalent of a resistive circuit. The syntax is :TF

EXAMPLE 15.10 15-10.

houtput variablei

hinput variablei

Use the command .TF to ﬁnd the The´venin equivalent of the circuit seen at terminal AB in Fig.

Fig. 15-10 The node numbers and element names are shown on Fig. 15-10.

The source ﬁle is

Transfer Function in Fig. 15-10 Vs 1 0 DC 12 E1 4 0 2 0 10 R1 1 2 1k R2 2 0 2k R3 2 3 1k R4 3 4 200 .TF V(3) Vs .END The output ﬁle contains the following results: NODE (1)

VOLTAGE 12.0000

NODE (2)

VOLTAGE 2:0000

NODE (3)

VOLTAGE 17:0000

NODE (4)

VOLTAGE 20:000

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 1:400E 02 TOTAL POWER DISSIPATION

1:68E 01 WATTS

SMALL-SIGNAL CHARACTERISTICS V(3)/Vs ¼ 1:417E þ 00 INPUT RESISTANCE AT Vs ¼ 8:571E þ 02 OUTPUT RESISTANCE AT V(3) ¼ 6:944E þ 01 Therefore, VTh ¼ 1:417ð12Þ ¼ 17 V and RTh ¼ 69:44 .

15.7

OP AMP CIRCUITS

Operational ampliﬁers may be modeled by high input impedance and high gain voltage-controlled voltage sources. The model may then be used within a net list repeatedly. EXAMPLE 15.11 Find the transfer function V3 =Vs in the ideal op amp circuit of Fig. 15-11(a). The op amp is replaced by a voltage-dependent voltage source with a gain of 106 [see Fig. 15-11(b)]. The source ﬁle is

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

371

Fig. 15-11 Inverting Vs E1 R1 R2 .TF .END

op amp circuit, Fig. 15-11 1 0 DC 12 3 0 0 2 1E6 1 2 1k 2 3 2k V(3) Vs

The transfer function is written in the output ﬁle: NODE (1)

VOLTAGE 12.0000

NODE (2)

VOLTAGE 24.00E 06

NODE (3)

VOLTAGE 24.0000

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 1.200E 02 TOTAL POWER DISSIPATION

1.44E 01 WATTS

SMALL-SIGNAL CHARACTERISTICS V(3)/Vs ¼ 2:000E + 00 INPUT RESISTANCE AT Vs ¼ 1.000E + 03 OUTPUT RESISTANCE AT V(3) ¼ 0.000E + 00

.SUBCKT Statement A subcircuit is deﬁned by a set of statements beginning with .SUBCKT

hnamei

hexternal terminalsi

and terminating with an .ENDS statement. Within a netlist we refer to a subcircuit by Xaa

hnamei

hnodesi

Hence, the .SUBCKT statement can assign a name to the model of an op amp for repeated use. EXAMPLE 15.12 Given the circuit of Fig. 15-12(a), ﬁnd Is , If , V2 , and V6 for Vs varying from 0.5 to 2 V in 0.5-V steps. Assume a practical op amp [Fig. 15-12(b)], with Rin ¼ 100 k , Cin ¼ 10 pF, Rout ¼ 10 k , and an open loop gain of 105 . The source ﬁle employs the subcircuit named OPAMP of Fig. 15-12(b) whose description begins with .SUBCKT and ends with .ENDS. The X1 and X2 statements describe the two op amps by referring to the OPAMP subcircuit. Note the correspondence of node connections in the X1 and X2 statements with that of the external terminals speciﬁed in the .SUBCKT statement. The source ﬁle is Op amp circuit of Fig. 15-12 .SUBCKT OPAMP Rin 1 2 Cin 1 2 Rout 3 5

using .SUBCKT 1 2 3 4 10 E5 10 pF 10 k

372

CIRCUIT ANALYSIS USING SPICE AND PSPICE

Eout .ENDS

5 4

1 2

Vs Rs R1 R2 R3 R4 Rf X1 X2 .DC .PRINT .TF .END

1 0 1 2 2 3 3 4 4 5 5 6 6 2 0 3 0 5 Vs DC V(6)

DC .5 1k 5k 9k 1.2 k 6k 40 k OPAMP OPAMP 2 0.5 V(6) I(Vs)

4 0 6 0 0.5 V(2) Vs

[CHAP. 15

10 E5

I(R1)

I(Rf)

Fig. 15-12

The output ﬁle is DC TRANSFER CURVES Vs V(2) 5:000E 01 5:000E 01 1:000E þ 00 1:000E þ 00 1:500E þ 00 1:500E þ 00 2:000E þ 00 2:000E þ 00

V(6) 4:500E þ 00 9:000E þ 00 1:350E þ 01 1:800E þ 01

I(Vs) 3:372E 09 6:745E 09 1:012E 08 1:349E 08

I(R1) 1:000E 04 2:000E 04 3:000E 04 4:000E 04

I(Rf) 9:999E 0 2:000E 0 3:000E 0 4:000E 0

CHAP. 15]

373

CIRCUIT ANALYSIS USING SPICE AND PSPICE

NODE (1) (5)

VOLTAGE NODE .5000 (2) 13:00E 06 (6)

VOLTAGE .5000 4.4998

NODE (3) (X1.5)

VOLTAGE NODE VOLTAGE 9:400E 06 (4) :9000 9:3996 (X2.5) 12:9990

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 3:372E 09 TOTAL POWER DISSIPATION

1:69E 09

WATTS

SMALL-SIGNAL CHARACTERISTICS Vð6Þ=Vs ¼ 9:000E þ 00 INPUT RESISTANCE AT Vs ¼ 1:483E þ 08 OUTPUT RESISTANCE AT Vð6Þ ¼ 7:357E 02 There is no voltage drop across Rs . Therefore, Vð2Þ ¼ Vs and the overall gain is Vð6Þ=Vs ¼ Vð2Þ=Vs ¼ 9. current drawn by R1 is provided through the feedback resistor Rf .

15.8

The

AC STEADY STATE AND FREQUENCY RESPONSE

Independent AC Sources Independent ac sources are described by a statement with the following syntax: hnamei

AC

hnodesi

hmagnitudei

hphase in degreesi

Voltage sources begin with V and current sources with I. The convention for direction is the same as that for dc sources. EXAMPLE 15.13

Write data statements for the sources shown in Fig. 15-13.

Fig. 15-13 AC Source Voltage Current

hnamei Vs Is

hnodesi 2 1 3 4

htypei AC AC

hmagnitudei 14 2.3

hphasei 45 105

.AC Statement The .AC command sweeps the frequency of all ac sources in the circuit through a desired range or sets it at a desired value. The syntax is :AC

hsweep typei

hnumber of pointsi

hstarting fi

hending fi

For the ac steady state, hsweep typei is LIN. In order to have a single frequency, the starting and ending frequencies are set to the desired value and the number of points is set to one. .PRINT AC and .PLOT AC Statements The .PRINT AC statement prints the magnitude and phase of the steady-state output. The syntax is :PRINT

AC

hmagnitudesi

hphasesi

374

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

The magnitudes and phases of voltages are Vm(variable) and Vp(variable), respectively, and the magnitudes and phases of currents are Im(variable) and Ip(variable), respectively. The syntax for .PLOT AC is similar to that for .PRINT AC. EXAMPLE 15.14 In the series RLC circuit of Fig. 15-14(a) vary the frequency of the source from 40 to 60 kHz in 200 steps. Find the magnitude and phase of current I using .PLOT and .PROBE. The source ﬁle is AC analysis of series RLC, Fig. 15-14 Vs 1 0 AC 1 0 R 1 2 32 L 2 3 2m C 3 0 5n .AC LIN 200 40 k 60 k .PLOT AC Im(Vs) Ip(Vs) .PROBE Vm(1, 2) Vm(2,3) Vm(3) Im(Vs) .END

Ip(Vs)

The graph of the frequency response, plotted by Probe, is shown in Fig. 15-14(b).

Fig. 15-14

CHAP. 15]

15.9

CIRCUIT ANALYSIS USING SPICE AND PSPICE

375

MUTUAL INDUCTANCE AND TRANSFORMERS

The mutual inductance between inductors is modeled by a device whose name begins with K. The data statement syntax is hnamei

hinductor 1i

hinductor 2i

hcoupling coefficienti

The dot rule, which determines the sign of the mutual inductance term, is observed by making the dotted end of each inductor the ﬁrst node entered in its data statement. EXAMPLE 15.15

Write the three data statements which describe the coupled coils of Fig. 15-15.

Fig. 15-15 pﬃﬃﬃﬃﬃﬃﬃﬃ The coupling coeﬃcient is k12 ¼ 1:5= 2ð3Þ ¼ 0:61. The netlist contains the following: L1 L2 K12

1 3 L1

2 4 L2

2 3 0.61

EXAMPLE 15.16 Plot the input impedance Zin ¼ V1 =I1 in the circuit of Fig. 15-16(a) for f varying from 0.01 to 1 Hz. To ﬁnd Zin , we connect a 1-A ac current source running from node 0 to node 1 and plot the magnitude and phase of the voltage V(1) across it. The source ﬁle is AC analysis of coupled coils, Fig. 15-16 IADD 0 1 AC 1 C 0 1 1 000 000 uF R 0 2 3 L1 1 2 2H L2 3 2 5H K12 L1 L2 0.6325 H L3 0 3 1H .AC LIN 20 .01 1 .PRINT AC Vm(1) Vp(1) .PROBE .END

0

Vm(1) and Vp(1), which are the magnitude and phase of Zin , are plotted by using Probe and the graph is shown in Fig. 15-16(b). Note that the maximum occurs at about 100 mHz.

15.10

MODELING DEVICES WITH VARYING PARAMETERS

.MODEL Statement The parameters of a passive element can be varied by using .MODEL statement. The syntax is :MODEL

hnamei

htypei

where hnamei is the name assigned to the element.

½ðhparameteri ¼ hvalueiÞ For passive linear elements, htypei is

RES for resistor IND for inductor CAP for capacitor

376

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

We can sweep the parameter of the model though a desired range at desired steps by using the .STEP statement: :STEP LIN

hnamei

hinitial valuei

hfinal valuei

hstep sizei

As an example, the following two statements use .MODEL and .STEP commands to deﬁne a resistor called heater with the resistance parameter varying from 20 to 40 in 5 steps generating 20, 25, 30, 35, and 40 : .MODEL .STEP

heater RES

RES(R ¼ 20Þ heater(R) 20

40

5

Fig. 15-16

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

377

EXAMPLE 15.17 Use Probe to plot V in the circuit in Fig. 15-17(a) for f varying from 1 to 3 kHz in 100 steps. also, R from 500 to 1 k in steps of 100 . Using .MODEL command we create the resistor RLeak and sweep its value by .STEP in the following source ﬁle. The graph of the frequency response V versus f is plotted by using Probe and it is shown in Fig. 15-17(b). Parallel resonance with variable R, Fig. I 0 1 AC R 1 0 RLeak L 1 0 10 m C 1 0 1u .MODEL RLeak RES(R ¼ 1Þ .STEP LIN RES .AC LIN 100 1k .PROBE .END

15-17 1m 0 1

RLeak(R) 3k

Fig. 15-17

500

1k

100

378

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

15.11 TIME RESPONSE AND TRANSIENT ANALYSIS .TRAN statement Time responses, such as natural responses to initial conditions in a source-free circuit and responses to step, pulse, exponential, or other time-dependent inputs, are produced by the .TRAN statement. The response begins at t ¼ 0. The increment size and ﬁnal time value are given in the following statement: :TRAN

hincrement sizei

hfinal time valuei

EXAMPLE 15.18 Use .TRAN and .PROBE to plot the voltage across the parallel RLC combination in Fig. 15-18(a) for R ¼ 50 and 150 for 0 < t < 1:4 ms. The initial conditions are Ið0Þ ¼ 0:5 A and Vð0Þ ¼ 0.

Fig. 15-18 The source ﬁle is Source-free parallel RLC with variable R R 1 0 LOSS L 0 1 10 m C 1 0 1u .MODEL LOSS RES(R ¼ 6Þ

1 IC ¼ :5 IC ¼ 0

CHAP. 15]

.STEP .TRAN .PROBE .END

CIRCUIT ANALYSIS USING SPICE AND PSPICE

RES 2.0E 6

LOSS(R) 1:4E 3

50 UIC

150

Figure 15-18(b) shows the graph of the voltage plotted by Probe.

15.12

379

100

For R ¼ 50 there are no oscillations.

SPECIFYING OTHER TYPES OF SOURCES

Time-dependent sources which include dc, ac, and transient components are expressed by hnamei

hnodesi

hdc comp:i

hac comp:i

htransient comp.i

The default for the unspeciﬁed dc or ac component is zero. The transient component appears for t > 0. Several transient components are described below. Exponential Source The source starts at a constant initial value V0 . At t0 , it changes exponentially from V0 to a ﬁnal value V1 with a time constant tau1. At t ¼ T, it returns exponentially to V0 with a time constant tau2. Its syntax is EXPðV0

V1

t0

tau1

T

tau2Þ

EXAMPLE 15.19 A 1-V dc voltage source starts increasing exponentially at t ¼ 5 ms, with a time constant of 5 ms and an asymptote of 2 V. After 15 ms, it starts decaying back to 1 V with a time constant of 2 ms. Write the data statement for the source and use Probe to plot the waveform. The data statement is Vs 1

0 EXPð1

2 5m

The waveform is plotted as shown in Fig. 15-19.

Fig. 15-19

5 m 20 m 2 mÞ

380

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

Pulse Source A periodic pulse waveform which goes from V0 to V1 and back can be represented by PULSEðV0

V1

delay

risetime

falltime

duration

periodÞ

EXAMPLE 15.20 (a) Write the data statement for a pulse waveform which switches 10 times in one second between 1 V and 2 V, with a rise and fall time of 2 ms. The pulse stays at 2 V for 11 ms. The ﬁrst pulse starts at t ¼ 5 ms. (b) Using Probe, plot the waveform in (a). (a) The data statement is Vs

1

0

PULSEð1 2 5 m

2 m 2 m 11 m 100 mÞ

(b) The waveform is plotted as shown in Fig. 15-20.

Fig. 15-20

Sinusoidal Source The source starts at a constant initial value V0 . At t0 , the exponentially decaying sinusoidal component with frequency f , phase angle, starting amplitude V1 , and decay factor alpha is added to it. The syntax for the waveform is SINð V0

V1

f

t0

alpha

phase Þ

EXAMPLE 15.21 (a) Write the mathematical expression and data statement for a dc voltage source of 1 V to which a 100-Hz sine wave with zero phase is added at t ¼ 5 ms. The amplitude of the sine wave is 2 V and it decays to zero with a time constant of 10 ms. (b) Using Probe, plot Vs ðtÞ.

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

(a) The decay factor is the inverse of the time constant and is equal to alpha ¼ 1=0:01 ¼ 100. voltage is expressed by

381

For t > 0, the

Vs ðtÞ ¼ 1 þ 2e100ðt0:005Þ sin 628:32ðt 0:005Þuðt 0:005Þ The data statement is Vs

1 0

SINð1 2 100 5 m 100Þ

(b) The waveform is plotted as shown in Fig. 15-21.

Fig. 15-21

EXAMPLE 15.22 Find the voltage across a 1-mF capacitor, with zero initial charge, which is connected to a voltage source through a 1-k resistor as shown in the circuit in Fig. 15-22(a). The voltage source is described by 15:819 V for 0 < t < 1 ms Vs ¼ 10 V for t > 1 ms We use the exponential waveform to represent Vs .

The ﬁle is

Dead-beat Pulse-Step response of RC Vs 1 0 EXP( 10 15:819 0 1:0E 6 1:0E 3 R 1 2 1k C 2 0 1 uF .TRAN 1:0E 6 5:0E 3 UIC .PROBE .END

1:0E 6Þ

The graph of the capacitor voltage is shown in Fig. 15-22(b). During 0 < t < 1 ms, the transient response grows exponentially toward a dc steady-state value of 15.819 V. At t ¼ 1 ms, the response reaches the value of 10 V. Also at t ¼ 1 ms, the voltage source drops to 10 V. Since the source and capacitor voltages are equal, the current in the resistor becomes zero and the steady state is reached. The transient response lasts only 1 ms.

382

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

Fig. 15-22

15.13

SUMMARY

In addition to the linear elements and sources used in the preceding sections, nonlinear devices, such as diodes (Dxx), junction ﬁeld-eﬀect transistors (Jxx), mosfets (Mxx), transmission lines (Txx), voltage controlled switches (Sxx), and current controlled switches (Wxx), may be included in the netlist. Sensitivity analysis is done using the .SENS statement. Fourier analysis is done using the .FOUR statement. These can be found in books or manuals for PSpice or Spice. The following summarizes the statements used in this chapter. Data Statements: R, L, C Mutual Inductance Subcircuit Call DC Voltage source DC Current source

hnamei kxx Xxx Vxx Ixx

hnodesi hind:ai hnamei hnodesi hnodesi

hvaluei ½hinitial conditionsi hind:bi hcoupling coefficienti hconnection nodesi DC hvaluei DC hvaluei

CHAP. 15]

383

CIRCUIT ANALYSIS USING SPICE AND PSPICE

AC Voltage source AC Current source VCVS CCCS VCCS CCVS

Vxx Ixx Exx Fxx Gxx Hxx

hnodesi hnodesi hnodesi hnodesi hnodesi hnodesi

AC hmagnitudei AC hmagnitudei hcontroli hgaini hcontroli hgaini hcontroli hgaini hcontroli hgaini

hphasei hphasei

Control Statements: .AC hsweep typei hnumber of pointsi hstarting fi hending fi .DC hnamei hinitial valuei hfinal valuei hstep sizei .END .ENDS .IC hVðnodeÞ ¼ valuei .MODEL hnamei htypei ½ðhparameteri ¼ hvalueiÞ htypei is RES for resistor htypei is IND for inductor htypei is CAP for capacitor .LIB [hfile namei] .OP .PRINT DC houtput variablesi .PLOT DC houtput variablesi .PRINT AC hmagnitudesi hphasesi .PLOT AC hmagnitudesi hphasesi .PRINT TRAN houtput variablesi .PROBE [houtput variablesi .STEP LIN htypei hname(param.)i hinitial valuei hfinal valuei .SUBCKT hnamei hexternal terminalsi .TF houtput variablei hinput sourcei .TRAN hincrement sizei hfinal valuei

Solved Problems 15.1

Use PSpice to ﬁnd Vð3; 4Þ in the circuit of Fig. 15-23.

Fig. 15-23 The source ﬁle is DC analysis, Fig. 15-23 Vs 2 0 R1 0 1 R2 0 1

DC 36 12

105 V

hstep sizei

384

CIRCUIT ANALYSIS USING SPICE AND PSPICE

R3 R4 R5 R6 .DC .PRINT .END

1 2 3 4 Vs DC

2 3 4 0 105 V(1)

74 16.4 103.2 28.7 105 V(3, 4)

[CHAP. 15

1

The output ﬁle contains the following: DC TRANSFER CURVES Vs V(1) 1:050E þ 02 1:139E þ 01

V(3, 4) 7:307E þ 01

Therefore, Vð3; 4Þ ¼ 73:07 V.

15.2

Write the source ﬁle for the circuit of Fig. 15-24 and ﬁnd I in R4 .

Fig. 15-24

The source ﬁle is DC analysis, VS Is R1 R2 R3 R4 .DC .PRINT .END

Fig. 15-24 2 0 0 3 0 1 1 2 1 3 3 0 Vs 200 DC I(R4)

DC DC 27 47 4 23 200

200 V 20 A

1

The output ﬁle contains the following results: DC TRANSFER CURVE Vs I(R4) 2:000E þ 02 1:123E þ 01 Current IðR4Þ ¼ 11:23 A ﬂows from node 3 to node 0 according to the order of nodes in the data statement for R4.

15.3

Find the three loop currents in the circuit of Fig. 15-25 using PSpice and compare your solution with the analytical approach.

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

385

Fig. 15-25

The source ﬁle is DC analysis, V1 V2 R1 R2 R3 R4 R5 .DC .PRINT .END

Fig. 15-25 2 0 0 4 0 1 1 2 1 3 3 0 3 4 V1 25 DC I(R1)

DC DC 2 5 10 4 2 25 I(R3)

25 50

1 I(R5)

The output ﬁle includes the following results: DC TRANSFER CURVES V1 I(R1) 2:500E þ 01 1:306E þ 00

I(R3) 3:172E þ 00

I(R5) 1:045E þ 01

The analytical solution requires solving three simultaneous equations.

15.4

Using PSpice, ﬁnd the value of Vs in Fig. 15-4 such that the voltage source does not supply any power. We sweep Vs from 1 to 10 V. The source and output ﬁles are DC sweep in the circuit of Fig. 15-4 R1 0 1 500 R2 1 2 3k R3 2 3 1k R4 0 3 1.5 k Vs 3 1 DC 4V Is 0 2 DC 3 mA .DC Vs 1 10 1 .PRINT DC I(Vs) .PROBE .PLOT DC I(Vs) .END The output ﬁle contains the following results: DC TRANSFER CURVES Vs I(Vs) 1:000E þ 00 7:500E 04 2:000E þ 00 2:188E 12 3:000E þ 00 7:500E 04

386

CIRCUIT ANALYSIS USING SPICE AND PSPICE

4:000E þ 00 5:000E þ 00 6:000E þ 00 7:000E þ 00 8:000E þ 00 9:000E þ 00 1:000E þ 01

[CHAP. 15

1:500E 03 2:250E 03 3:000E 03 3:750E 03 4:500E 03 5:250E 03 6:000E 03

The current in Vs is zero for Vs ¼ 2 V.

15.5

Perform a dc analysis on the circuit of Fig. 15-26 and ﬁnd its The´venin equivalent as seen from terminal AB.

Fig. 15-26 We include a .TF statement in the following netlist: The´venin Vs R1 Is .TF .END

equivalent of Fig. 15-26 1 0 DC 3 1 2 10 0 2 DC 1 V(2) Is

The output ﬁle includes the following results: NODE (1)

VOLTAGE 3.0000

NODE (2)

VOLTAGE 13.000

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 1:000E þ 00 TOTAL POWER DISSIPATION

3:00E þ 00

WATTS

SMALL-SIGNAL CHARACTERISTICS Vð2Þ=Is ¼ 1:000E þ 01 INPUT RESISTANCE AT Is ¼ 1:000E þ 01 OUTPUT RESISTANCE AT Vð2Þ ¼ 1:000E þ 01 The The´venin equivalent is VTh ¼ V2 ¼ 13 V, RTh ¼ 10 .

15.6

Perform an ac analysis on the circuit of Fig. 15-27(a). Find the complex magnitude of V2 for f varying from 100 Hz to 10 kHz in 10 steps. We add to the netlist an .AC statement to sweep the frequency and obtain V(2) by any of the commands .PRINT, .PLOT, or .PROBE. The source ﬁle is AC analysis of Fig. Vs 1 R1 1 R2 2

15-27(a). 0 AC 2 1k 0 2k

10

0

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

C .AC .PRINT .PLOT .PROBE .END

2 0 LIN AC AC

1 uF 10 Vm(2) Vm(2) Vm(2)

100

10000 Vp(2) Vp(2) Vp(2)

Fig. 15-27 The output ﬁle contains the following results: AC ANALYSIS FREQ 1:000E þ 02 1:200E þ 03 2:300E þ 03 3:400E þ 03 4:500E þ 03

VM(2) 6:149E þ 00 1:301E þ 00 6:883E 01 4:670E 01 3:532E 01

VP(2) 2:273E þ 01 7:875E þ 01 8:407E þ 01 8:598E þ 01 8:696E þ 01

387

388

CIRCUIT ANALYSIS USING SPICE AND PSPICE

5:600E þ 03 6:700E þ 03 7:800E þ 03 8:900E þ 03 1:000E þ 04

2:839E 01 2:374E 01 2:039E 01 1:788E 01 1:591E 01

[CHAP. 15

8:756E þ 01 8:796E þ 01 8:825E þ 01 8:846E þ 01 8:863E þ 01

The magnitude and phase of V2 are plotted with greater detail in Fig. 15-27(bÞ.

15.7

Perform dc and ac analysis on the circuit in Fig. 15-28. Find the complex magnitude of V2 for f varying from 100 Hz to 10 kHz in 100 steps.

Fig. 15-28 The source ﬁle is DC and AC Vs Is R1 R2 C .AC .PROBE .END

analysis of Fig. 15-28 1 0 AC 0 2 DC 1 2 1k 2 0 2k 2 0 1 uF LIN 100 Vm(2) Vp(2)

10 1 mA

0

100

10000

The output ﬁle contains the following results: SMALL SIGNAL BIAS SOLUTION NODE VOLTAGE NODE VOLTAGE (1) 0.0000 (2) .6667 VOLTAGE SOURCE CURRENTS NAME CURRENT Vs 6:667E 04 TOTAL POWER DISSIPATION

0:00E þ 00

WATTS

The graph of the ac component of V2 is identical with that of V2 of Problem 15.6 shown in Fig. 1527(b).

15.8

Plot resonance curves for the circuit of Fig. 15-29(a) for R ¼ 2, 4, 6, 8, and 10 . We model the resistor as a single-parameter resistor element with a single-parameter R and change the value of its parameter R from 2 to 10 in steps of 2 . We use the .AC command to sweep the frequency from 500 Hz to 3 kHz in 100 steps. The source ﬁle is Parallel resonance of practical coil, Fig. 15-29 I 0 2 AC 1m R 0 2 RLOSS 1 L 1 2 10 m C 0 2 1u .MODEL RLOSS RESðR ¼ 1Þ

0

CHAP. 15]

389

CIRCUIT ANALYSIS USING SPICE AND PSPICE

.STEP .AC .PROBE .END

RES LIN

RLOSS(R) 100 500

2 10 3000

2

The resonance curves are shown with greater detail in Fig. 15-29(b).

Fig. 15-29

15.9

Use .TRAN and .PROBE to plot VC across the 1-mF capacitor in the source-free circuit of Fig. 15-30(a) for R ¼ 100, 600, 1100, 1600, and 2100 . The initial voltage is VC ð0Þ ¼ 10 V. The values of the resistor R are changed by using .MODEL and .STEP.

The source ﬁle is

390

CIRCUIT ANALYSIS USING SPICE AND PSPICE

Natural response of RC, Fig. 15-30(a) R 0 1 Rshunt C 1 0 1 uF .MODEL Rshunt RESðR ¼ 1Þ .STEP LIN RES .TRAN 1E 4 50E 4 .PLOT TRAN V(1) .PROBE .END

[CHAP. 15

1 IC ¼ 10 Rshunt(R) UIC

100

2.1 k

500

The graph of the voltage VC is shown in Fig. 15-30(b).

Fig. 15-30

15.10 Plot the voltages between the two nodes of Fig. 15-31(a) in response to a 1-mA step current source for R ¼ 100, 600, 1100, 1600, and 2100 .

CHAP. 15]

391

CIRCUIT ANALYSIS USING SPICE AND PSPICE

The source ﬁle is Step response of RC, Fig. 15-31(a) I 0 1 1m R 0 1 Rshunt C 1 0 1 uF .MODEL Rshunt RESðR ¼ 1Þ .STEP LIN RES .TRAN 1E 4 50E 4 .PLOT TRAN V(1) .PROBE .END

1

Rshunt(R) UIC

The graphs of the step responses are given in Fig. 15-31(b).

Fig. 15-31

100

2.1 k

500

392

CIRCUIT ANALYSIS USING SPICE AND PSPICE

[CHAP. 15

15.11 Find the The´venin equivalent of Fig. 15-32 seen at the terminal AB:

Fig. 15-32 From dc analysis we ﬁnd the open-circuit voltage at AB. We also use .TF to ﬁnd the output resistance at AB. The source ﬁle and the output ﬁles are Solution to Fig. R1 0 R2 0 R3 1 R4 2 R5 4 Vs1 2 Vs2 3 Is 0 .TF V(5) .END

15-32 and The´venin equivalent at terminal AB 1 2 3 6 3 1 3 5 5 7 1 DC 3 4 DC 4 5 DC 1 Vs1

The output ﬁle contains the following results: NODE VOLTAGE (1) 1.2453 (5) 5.2642

NODE VOLTAGE (2) 4.2453

NODE VOLTAGE (3) 2.2642

NODE VOLTAGE (4) 1:7358

VOLTAGE SOURCE CURRENTS NAME CURRENT Vs1 3:962E 01 Vs2 1:000E þ 00 TOTAL POWER DISSIPATION

5:19E þ 00

WATTS

Vð5Þ=Vs1 ¼ 1:132E 01 INPUT RESISTANCE AT Vs1 ¼ 5:889E þ 00 OUTPUT RESISTANCE AT Vð5Þ ¼ 8:925E þ 00 The The´venin equivalent is VTh ¼ V5 ¼ 5:2642 V, RTh ¼ 8:925 .

15.12 Plot the frequency response VAB =Vac of the open-loop ampliﬁer circuit of Fig. 15-33(a). The following source ﬁle chooses 500 points within the frequency varying from 100 Hz to 10 Mhz. Open loop frequency response of ampliﬁer, Fig. 15-33 Rs 1 2 10 k Rin 0 2 10 E5 Cin 0 2 short 1 Rout 3 4 10 k R1 4 0 10 E9 Eout 3 0 0 2 1 E5 Vac 1 0 AC 10 u 0 .MODEL short CAP(C ¼ 1Þ

CHAP. 15]

393

CIRCUIT ANALYSIS USING SPICE AND PSPICE

.STEP .AC .PROBE .END

LIN LIN

CAP 500

short(C) 1 pF 10 10000 k

101 pF

25 pF

The frequency response is plotted by Probe for the frequency varying from 10 kHz to 10 MHz as shown in Fig. 15-33(b).

Fig. 15-33

15.13 Model the op amp of Fig. 15-34(a) as a subcircuit and use it to ﬁnd the frequency response of V3 =Vac in Fig. 15-34ðbÞ for f varying from 1 MHz to 1 GHz. The source ﬁle is Closed loop frequency response of ampliﬁer, Fig. 15-34 .SUBCKT OPAMP 1 2 3 4

394

CIRCUIT ANALYSIS USING SPICE AND PSPICE

Fig. 15-34

[CHAP. 15

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

* node * node * node * node * node Rin Cin Rout Eout .ENDS Vac R1 Rf X1 .MODEL .STEP .AC .PROBE .END

1 2 3 4 5

is is is is is

395

the non-inverting input the inverting input the output the output reference (negative end of dependent source) the positive end of dependent source 1 2 10 E5 1 2 100 pF 3 5 10 k 5 4 1 2 1 E5 1 0 1 2 2 3 0 2 3 0 GAIN LIN LIN

AC 10 m 0 10 k Rgain 1 OPAMP RES(R ¼ 1Þ RES Rgain(R) 1 k 801 k 500 1000 k 1 000 000 k

200 k

The frequency response is graphed in Fig. 15-34(c). Compared with the open-loop circuit of Fig. 1533(a), the dc gain is reduced and the bandwidth is increased.

15.14 Referring to the RC circuit of Fig. 15-22, choose the height of the initial pulse such that the voltage across the capacitor reaches 10 V in 0.5 ms. Verify your answer by plotting Vc for 0 < t < 2 ms. The pulse amplitude A is computed from Að1 e1=2 Þ ¼ 10

from which

We describe the voltage source using PULSE syntax. Pulse-Step Vs R C .TRAN .PROBE .END

A ¼ 25:415 V

The source ﬁle is

response of RC, dead beat in RC/2 seconds 1 0 PULSE( 10 25:415 1:0E 6 1:0E 6 0:5 m 3 m Þ 1 2 1k 2 0 1u 1:0E 6 2:0E 3 UIC

The response shape is similar to the graph in Fig. 15-22(b). During the transition period of 0 < t < 0:5 ms, the voltage increases exponentially toward a dc steady state value of 25.415 V. However, at t ¼ 0:5 ms, when the capacitor voltage reaches 10 V, the source also has 10 V across it. The current in the resistor becomes zero and steady state is reached.

15.15 Plot the voltage across the capacitor in the circuit in Fig. 15-35(a) for R ¼ 0:01 and 4:01 . The current source is a 1 mA square pulse which lasts 1256.64 ms as shown in the i t graph. Model the resistor as a single-parameter resistor element with a single parameter R and change the value of R from 0.01 to 4.01 in step of 4. We use the .AC command to sweep the frequency from 500 Hz to 3 kHz in 100 steps. The source ﬁle is Pulse response of RLC with variable R Is 0 1 Pulse( 0 1 m 100 u 0:01 u 0:01 u R 1 2 LOSS 1 C 1 0 2000 n IC ¼ 0 L 2 0 5m IC ¼ 0

1256:64 u 5000 u Þ

396

CIRCUIT ANALYSIS USING SPICE AND PSPICE

.MODEL .STEP .TRAN .PROBE .END

LOSS RES 10 u

[CHAP. 15

RESðR ¼ 1Þ LOSS(R) .01 4.01 4 3500 u 0 1u UIC

The result is shown in Fig. 15-35(b). The transient response is almost zero for R ¼ 0:01 . This is because pulse width is a multiple of the period of natural oscillations of the circuit.

Fig. 15-35

CHAP. 15]

CIRCUIT ANALYSIS USING SPICE AND PSPICE

Supplementary Problems In the following problems, use PSpice to repeat the indicated problems and examples. 15.16

Solve Example 5.9 (Fig. 5-12).

15.17

Solve Example 5.11 (Fig. 5-16).

15.18

Solve Example 5.14 (Fig. 5-20).

15.19

Solve Example 5.15 (Fig. 5-21).

15.20

Solve Example 5.20 (Fig. 5-28) for xðtÞ ¼ 1 V.

15.21

Solve Problem 5.12 (Fig. 5-37).

15.22

Solve Problem 5.16 (Fig. 5-39).

15.23

Solve Problem 5.25 (Fig. 5-48).

15.24

Solve Problem 5.26 (Fig. 5-49).

15.25

Solve Problem 5.48 (Fig. 5-55) for vs1 ¼ vs2 ¼ 1 V.

15.26

Solve Example 7.3.

15.27

Solve Example 7.6 (Fig. 7-12).

15.28

Solve Example 7.7 [Fig. 7-13(a)].

15.29

Solve Example 7.11 [Fig. 7-17(a)].

15.30

Solve Problem 8.27 (Fig. 8-31).

15.31

Solve Problem 9.11 (Fig. 9-20).

15.32

Solve Problem 9.18 (Fig. 9-28).

15.33

Solve Problem 9.19 (Fig. 9-29).

15.34

Solve Example 11.5 [Fig. 11-15(a)].

15.35

Solve Example 11.6 [Fig. 11-16(a)].

15.36

Solve Example 11.7 (Fig. 11-17).

15.37

Solve Problem 12.7.

15.38

Solve Problem 12.14 (Fig. 12-40).

15.39

Solve Problem 12.16 (Fig. 12-43).

15.40

Solve Problem 13.28 (Fig. 13-31) for s ¼ j.

15.41

Solve Problem 13.31 (Fig. 13-33)

15.42

Solve Problem 14.8 (Fig. 14-24).

15.43

Solve Problem 14.12 (Fig. 14-28).

15.44

Solve Problem 14.13 (Fig. 14-29)

15.45

Solve Problem 14.20 (Fig. 14-35)

15.46

Solve Problem 14.21 (Fig. 14-36) for s ¼ j.

397

The Laplace Transform Method 16.1

INTRODUCTION

The relation between the response yðtÞ and excitation xðtÞ in RLC circuits is a linear diﬀerential equation of the form an yðnÞ þ þ aj yð jÞ þ þ a1 yð1Þ þ a0 y ¼ bm xðmÞ þ þ bi xðiÞ þ þ b1 xð1Þ þ b0 x ð jÞ

ð1Þ

ðiÞ

where y and x are the jth and ith time derivatives of yðtÞ and xðtÞ, respectively. If the values of the circuit elements are constant, the corresponding coeﬃcients aj and bi of the diﬀerential equation will also be constants. In Chapters 7 and 8 we solved the diﬀerential equation by ﬁnding the natural and forced responses. We employed the complex exponential function xðtÞ ¼ Xest to extend the solution to the complex frequency s-domain. The Laplace transform method described in this chapter may be viewed as generalizing the concept of the s-domain to a mathematical formulation which would include not only exponential excitations but also excitations of many other forms. Through the Laplace transform we represent a large class of excitations as an inﬁnite collection of complex exponentials and use superposition to derive the total response.

16.2

THE LAPLACE TRANSFORM

Let f ðtÞ be a time function which is zero for t 0 and which is (subject to some mild conditions) arbitrarily deﬁned for t > 0. Then the direct Laplace transform of f ðtÞ, denoted l½ f ðtÞ, is deﬁned by ð1 l½ f ðtÞ ¼ FðsÞ ¼ f ðtÞest dt ð2Þ 0þ

Thus, the operation l½ transforms f ðtÞ, which is in the time domain, into FðsÞ, which is in the complex frequency domain, or simply the s-domain, where s is the complex variable þ j!. While it appears that the integration could prove diﬃcult, it will soon be apparent that application of the Laplace transform method utilizes tables which cover all functions likely to be encountered in elementary circuit theory. There is a uniqueness in the transform pairs; that is, if f1 ðtÞ and f2 ðtÞ have the same s-domain image FðsÞ, then f1 ðtÞ ¼ f2 ðtÞ. This permits going back in the other direction, from the s-domain to the time 398 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

399

domain, a process called the inverse Laplace transform, l1 ½FðsÞ ¼ f ðtÞ. The inverse Laplace transform can also be expressed as an integral, the complex inversion integral: ð 1 0 þj1 l1 ½FðsÞ ¼ f ðtÞ ¼ FðsÞest ds ð3Þ 2j 0 j1 In (3) the path of integration is a straight line parallel to the j!-axis, such that all the poles of FðsÞ lie to the left of the line. Here again, the integration need not actually be performed unless it is a question of adding to existing tables of transform pairs. It should be remarked that taking the direct Laplace transform of a physical quantity introduces an extra time unit in the result. For instance, if iðtÞ is a current in A, then IðsÞ has the units A s (or C). Because the extra unit s will be removed in taking the inverse Laplace transform, we shall generally omit to cite units in the s-domain, shall still call IðsÞ a ‘‘current,’’ indicate it by an arrow, and so on.

16.3

SELECTED LAPLACE TRANSFORMS The Laplace transform of the unit step function is easily obtained: ð1 1 1 l½uðtÞ ¼ ð1Þest dt ¼ ½est 1 0 ¼ s s 0

From the linearity of the Laplace transform, it follows that vðtÞ ¼ VuðtÞ in the time domain has the sdomain image VðsÞ ¼ V=s. The exponential decay function, which appeared often in the transients of Chapter 7, is another time function which is readily transformed. ð1 A ðaþsÞt 1 A ½e l½Aeat ¼ Aeat est dt ¼ 0 ¼ Aþs sþa 0 or, inversely, l

1

A ¼ Aeat sþa

The transform of a sine function is also easily obtained. 1 ð1 sðsin !tÞest est ! cos !t ! ðsin !tÞest dt ¼ ¼ 2 l½sin !t ¼ 2 2 þ ! þ !2 s s 0 0 It will be useful now to obtain the transform of a derivative, df ðtÞ=dt. ð1 df ðtÞ df ðtÞ st e dt l ¼ dt dt 0 Integrating by parts, ð1 ð1 df ðtÞ st 1 st þ f ðtÞðse Þ dt ¼ f ð0 Þ þ s f ðtÞest dt ¼ f ð0þ Þ þ sFðsÞ l ¼ ½e f ðtÞ0þ dt 0 0 A small collection of transform pairs, including those obtained above, is given in Table 16-1. The last ﬁve lines of the table present some general properties of the Laplace transform. EXAMPLE 16.1 Consider a series RL circuit, with R ¼ 5 and L ¼ 2:5 mH. At t ¼ 0, when the current in the circuit is 2 A, a source of 50 V is applied. The time-domain circuit is shown in Fig. 16-1.

400

THE LAPLACE TRANSFORM METHOD

Time Domain (i) Ri + L di = L dt

[CHAP. 16

s-Domain (ii) RI(s) + L[_ i(0+) + sI(s)] = V(s) _

(iii) 5I(s) + (2.5× 10 3)[_2 +sI(s)]=

50 s

(classical methods) _8 10 + s s+2000 _ 1 =10 10L 1 s _ _ 1 (_8)L 1 = _ 8e 2000t s+2000

(iv) I(s)= (v) (vii) i(t) = 10 _ 8e

_2000t

(A)

(vi)

Table 16-1 Laplace Transform Pairs f ðtÞ

FðsÞ

1.

1

2.

t

3.

eat

4.

teat

5.

sin !t

6.

cos !t

1 s 1 s2 1 sþa 1 ðs þ aÞ2 ! s2 þ ! 2 s s2 þ ! 2

7.

sin ð!t þ Þ

s sin þ ! cos s2 þ ! 2

8.

cos ð!t þ Þ

9.

eat sin !t

10.

eat cos !t

11.

sinh !t

12.

cosh !t

sþa ðs þ aÞ2 þ !2 ! s2 ! 2 s s2 ! 2

13.

df dt

sFðsÞ f ð0þ Þ

ðt

f ðÞ d

s cos ! sin s2 þ ! 2 ! ðs þ aÞ2 þ !2

FðsÞ s

14.

0

15.

f ðt t1 Þ

et1 s FðsÞ

16.

c1 f1 ðtÞ þ c2 f2 ðtÞ ðt f1 ðÞ f2 ðt Þ d

c1 F1 ðsÞ þ c2 F2 ðsÞ

17.

0

F1 ðsÞF2 ðsÞ

CHAP. 16]

401

THE LAPLACE TRANSFORM METHOD

Fig. 16-1

Fig. 16-2

Kirchhoﬀ’s voltage law, applied to the circuit for t > 0, yields the familiar diﬀerential equation (i). This equation is transformed, term by term, into the s-domain equation (ii). The unknown current iðtÞ becomes IðsÞ, while the known voltage v ¼ 50uðtÞ is transformed to 50/s. Also, di=dt is transformed into ið0þ Þ þ sIðsÞ, in which ið0þ Þ is 2 A. Equation (iii) is solved for IðsÞ, and the solution is put in the form (iv) by the techniques of Section 16.6. Then lines 1, 3, and 16 of Table 16-1 are applied to obtain the inverse Laplace transform of IðsÞ, which is iðtÞ. A circuit can be drawn in the s-domain, as shown in Fig. 16-2. The initial current appears in the circuit as a voltage source, Lið0þ Þ. The s-domain current establishes the voltage terms RIðsÞ and sLIðsÞ in (ii) just as a phasor current I and an impedance Z create a phasor voltage IZ.

16.4

CONVERGENCE OF THE INTEGRAL

For the Laplace transform to exist, the integral (2) should converge. This limits the variable s ¼ þ j! to a part of the complex plane called the convergence region. As an example, the transform of xðtÞ ¼ eat uðtÞ is 1=ðs þ aÞ, provided Re ½s > a, which deﬁnes its region of convergence. EXAMPLE 16.2

Find the Laplace transform of xðtÞ ¼ 3e2t uðtÞ and show the region of convergence. ð1 ð1 3 3 ½eðs2Þt 1 ; Re ½s > 2 XðsÞ ¼ 3e2t est dt ¼ 3eðs2Þt dt ¼ 0 ¼ s 2 s 2 0 0

The region of convergence of XðsÞ is the right half plane > 2, shown hatched in Fig. 16-3.

Fig. 16-3

16.5

INITIAL-VALUE AND FINAL-VALUE THEOREMS

Taking the limit as s ! 1 (through real values) of the direct Laplace transform of the derivative, df ðtÞ=dt, lim l

s!1

ð1 df ðtÞ df ðtÞ st e dt ¼ lim fsFðsÞ f ð0þ Þg ¼ lim s!1 0 s!1 dt dt

402

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

But est in the integrand approaches zero as s ! 1. Thus, lim fsFðsÞ f ð0þ Þg ¼ 0

s!1

Since f ð0þ Þ is a constant, we may write f ð0þ Þ ¼ lim fsFðsÞg s!1

which is the statement of the initial-value theorem. EXAMPLE 16.3 In Example 16.1, lim fsIðsÞg ¼ lim 10

s!1

s!1

8s ¼ 10 8 ¼ 2 s þ 2000

þ

which is indeed the initial current, ið0 Þ ¼ 2 A. The ﬁnal-value theorem is also developed from the direct Laplace transform of the derivative, but now the limit is taken as s ! 0 (through real values). ð1 df ðtÞ df ðtÞ st lim l e dt ¼ limfsFðsÞ f ð0þ Þg ¼ lim s!0 s!0 0 s!0 dt dt ð1 ð1 df ðtÞ st lim But df ðtÞ ¼ f ð1Þ f ð0þ Þ e dt ¼ s!0 0 dt 0 and f ð0þ Þ is a constant. Therefore, f ð1Þ f ð0þ Þ ¼ f ð0þ Þ þ limfsFðsÞg s!0

f ð1Þ ¼ limfsFðsÞg

or

s!0

This is the statement of the ﬁnal-value theorem. The theorem may be applied only when all poles of sFðsÞ have negative real parts. This excludes the transforms of such functions as et and cos t, which become inﬁnite or indeterminate as t ! 1.

16.6

PARTIAL-FRACTIONS EXPANSIONS

The unknown quantity in a problem in circuit analysis can be either a current iðtÞ or a voltage vðtÞ. In the s-domain, it is IðsÞ or VðsÞ; for the circuits considered in this book, this will be a rational function of the form RðsÞ ¼

PðsÞ QðsÞ

where the polynomial QðsÞ is of higher degree than PðsÞ. Furthermore, RðsÞ is real for real values of s, so that any nonreal poles of RðsÞ, that is, nonreal roots of QðsÞ ¼ 0, must occur in complex conjugate pairs. In a partial-fractions expansion, the function RðsÞ is broken down into a sum of simpler rational functions, its so-called principal parts, with each pole of RðsÞ contributing a principal part. Case 1: s ¼ a is a simple pole. principal part of RðsÞ is

When s ¼ a is a nonrepeated root of QðsÞ ¼ 0, the corresponding

A sa

where

A ¼ limfðs aÞRðsÞg s!a

If a is real, so will be A; if a is complex, then a is also a simple pole and the numerator of its principal part is A . Notice that if a ¼ 0, A is the ﬁnal value of rðtÞ Case 2: s ¼ b is a double pole. When s ¼ b is a double root of QðsÞ ¼ 0, the corresponding principal part of RðsÞ is

CHAP. 16]

403

THE LAPLACE TRANSFORM METHOD

B1 B2 þ s b ðs bÞ2 where the constants B2 and B1 may be found as 2

B2 ¼ limfðs bÞ RðsÞg s!b

B1 ¼ lim ðs bÞ RðsÞ

and

s!b

B2 ðs bÞ2

B1 may be zero. Similar to Case 1, B1 and B2 are real if b is real, and these constants for the double pole b are the conjugates of those for b. The principal part at a higher-order pole can be obtained by analogy to Case 2; we shall assume, however, that RðsÞ has no such poles. Once the partial-functions expansion of RðsÞ is known, Table 16-1 can be used to invert each term and thus to obtain the time function rðtÞ. EXAMPLE 16.4

Find the time-domain current iðtÞ if its Laplace transform is s 10 s4 þ s2 s 10 IðsÞ ¼ 2 s ðs jÞðs þ jÞ IðsÞ ¼

Factoring the denominator,

we see that the poles of IðsÞ are s ¼ 0 (double pole) and s ¼ j (simple poles). The principal part at s ¼ 0 is

since

B1 B2 1 10 þ 2 ¼ 2 s s s s s 10 ¼ 10 B2 ¼ lim s!0 ðs jÞðs þ jÞ s 10 10 10s þ 1 B1 ¼ lim s 2 2 þ ¼1 ¼ lim 2 s!0 s!0 s þ 1 s ðs þ 1Þ s2 The principal part at s ¼ þj is A 0:5 þ j5 ¼ sj sj s 10 A ¼ lim 2 ¼ ð0:5 þ j5Þ s!j s ðs þ jÞ

since

It follows at once that the principal part at s ¼ j is

0:5 j5 sþj

The partial-fractions expansion of IðsÞ is therefore IðsÞ ¼

1 1 1 1 10 2 ð0:5 þ j5Þ ð0:5 j5Þ s sj sþj s

and term-by-term inversion using Table 16-1 gives iðtÞ ¼ 1 10t ð0:5 þ j5Þe jt ð0:5 j5Þejt ¼ 1 10t ðcos t 10 sin tÞ

Heaviside Expansion Formula If all poles of RðsÞ are simple, the partial-fractions expansion and termwise inversion can be accomplished in a single step: X n PðsÞ Pðak Þ ak t l1 e ð4Þ ¼ 0 QðsÞ Q ðak Þ k¼1 where a1 ; a2 ; . . . ; an are the poles and Q 0 ðak Þ is dQðsÞ=ds evaluated at s ¼ ak .

404

16.7

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

CIRCUITS IN THE s-DOMAIN

In Chapter 8 we introduced and utilized the concept of generalized impedance, admittance, and transfer functions as functions of the complex frequency s. In this section, we extend the use of the complex frequency to transform an RLC circuit, containing sources and initial conditions, from the time domain to the s-domain. Table 16-2 Time Domain

s-Domain Voltage Term

s-Domain

RIðsÞ

sLIðsÞ þ Lið0þ Þ

sLIðsÞ þ Lið0þ Þ

IðsÞ V0 þ sC s

IðsÞ V0 sc s

Table 16-2 exhibits the elements needed to construct the s-domain image of a given time-domain circuit. The ﬁrst three lines of the table were in eﬀect developed in Example 16.1. As for the capacitor, we have, for t > 0, vC ðtÞ ¼ V0 þ

1 C

ðt iðÞ d 0

so that, from Table 16-1, VC ðsÞ ¼

V0 IðsÞ þ Cs s

EXAMPLE 16.5 In the circuit shown in Fig. 16-4(a) an initial current i1 is established while the switch is in position 1. At t ¼ 0, it is moved to position 2, introducing both a capacitor with initial charge Q0 and a constant-voltage source V2 . The s-domain circuit is shown in Fig. 16-4(b). The s-domain equation is

RIðsÞ þ sLIðsÞ Lið0þ Þ þ in which V0 ¼ Q0 =C and ið0þ Þ ¼ i1 ¼ V1 =R.

IðsÞ V0 V2 þ ¼ sC sC s

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

405

Fig. 16-4

16.8

THE NETWORK FUNCTION AND LAPLACE TRANSFORMS

In Chapter 8 we obtained responses of circuit elements to exponentials est , based on which we introduced the concept of complex frequency and generalized impedance. We then developed the network function HðsÞ as the ratio of input-output amplitudes, or equivalently, the input-output diﬀerential equation, natural and forced responses, and the frequency response. In the present chapter we used the Laplace transform as an alternative method for solving diﬀerential equations. More importantly, we introduce Laplace transform models of R, L, and C elements which, contrary to generalized impedances, incorporate initial conditions. The input-output relationship is therefore derived directly in the transform domain. What is the relationship between the complex frequency and the Laplace transform models? A short answer is that the generalized impedance is the special case of the Laplace transform model (i.e., restricted to zero state), and the network function is the Laplace transform of the unit-impulse response. EXAMPLE 16.17 Find the current developed in a series RLC circuit in response to the following two voltage sources applied to it at t ¼ 0: (a) a unit-step, (b) a unit-impulse. The inductor and capacitor contain zero energy at t ¼ 0 . Therefore, the Laplace transform of the current is IðsÞ ¼ VðsÞYðsÞ. (a) VðsÞ ¼ 1=s and the unit-step response is 1 Cs 1 1 ¼ s LCs2 þ RCs þ 1 L ðs þ Þ2 þ !2d 1 t iðtÞ ¼ e sin ð!d tÞuðtÞ L!d

IðsÞ ¼

where R ; ¼ 2L

and

s ﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ﬃ R 2 1 !d ¼ 2L LC

(b) VðsÞ ¼ 1 and the unit-impulse response is 1 s L ðs þ Þ2 þ !2d 1 t iðtÞ ¼ e ½!d cos ð!d tÞ sin ð!d tÞuðtÞ L!d

IðsÞ ¼

The unit-impulse response may also be found by taking the time-derivative of the unit-step response. EXAMPLE 16.18 Find the voltage across terminals of a parallel RLC circuit in response to the following two current sources applied at t ¼ 0: (a) a unit-step, (b) a unit-impulse. Again, the inductor and capacitor contain zero energy at t ¼ 0 . Therefore, the Laplace transform of the current is VðsÞ ¼ IðsÞZðsÞ.

406

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

(a) IðsÞ ¼ 1=s and the unit-step response is 1 RLs 1 1 ¼ 2 s RLCs þ Ls þ 1 C ðs þ Þ2 þ !2d 1 t vðtÞ ¼ e sin ð!d tÞuðtÞ C!d

VðsÞ ¼

where 1 ; ¼ RC

and

sﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 2 1 !d ¼ 2RC LC

(b) IðsÞ ¼ 1 and the unit-impulse response is 1 1 C ðs þ Þ2 þ !2d 1 t vðtÞ ¼ e ½!d cos ð!d tÞ sin ð!d tÞuðtÞ C!d

VðsÞ ¼

Solved Problems 16.1

Find the Laplace transform of eat cos !t, where a is a constant. Ð1 Applying the deﬁning equation l½ f ðtÞ ¼ 0 f ðtÞest dt to the given function, we obtain ð1 l½eat cos !t ¼ cos !teðsþaÞt dt 0 " #1 ðs þ aÞ cos !teðsþaÞt þ eðsþaÞt ! sin !t ¼ ðs þ aÞ2 þ !2 0 sþa ¼ ðs þ aÞ2 þ !2

16.2

If l½ f ðtÞ ¼ FðsÞ, show that l½eat f ðtÞ ¼ Fðs þ aÞ.

Apply this result to Problem 16.1.

Ð1

f ðtÞest dt ¼ FðsÞ. Then, ð1 ð1 l½eat f ðtÞ ¼ ½eat f ðtÞest dt ¼ f ðtÞeðsþaÞt dt ¼ Fðs þ aÞ

By deﬁnition, l½ f ðtÞ ¼

0

0

0

Applying (5) to line 6 of Table 16-1 gives l½eat cos !t ¼

sþa ðs þ aÞ2 þ !2

as determined in Problem 16.1.

16.3

Find the Laplace transform of f ðtÞ ¼ 1 eat , where a is a constant. ð1 est dt eðsþaÞt dt 0 0 0 1 1 1 1 1 a eðsþaÞt ¼ ¼ ¼ est þ s sþa s s þ a sðs þ aÞ 0

l½1 eat ¼

ð1

ð1 eat Þest dt ¼

ð1

ð5Þ

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

Another Method ðt 1=ðs þ aÞ a a ¼ l a e d ¼ a s sðs þ aÞ 0

16.4

Find l1

1 2 sðs a2 Þ

Using the method of partial fractions, 1 A B C þ ¼ þ sðs2 a2 Þ s s þ a s a and the coeﬃcients are A¼ Hence,

1 1 1 1 1 1 ¼ B ¼ ¼ C ¼ ¼ sðs aÞ s¼a 2a2 sðs þ aÞ s¼a 2a2 s2 a2 s¼0 a2 " # " # " # 2 2 2 1 1 1=a 1 1=2a 1 1=2a ¼ l l1 þ l þ l s sþa sa sðs2 a2 Þ

The corresponding time functions are found in Table 16-1: 1 1 1 1 1 ¼ 2 þ 2 eat þ 2 eat l sðs2 a2 Þ a 2s 2a 1 1 eat þ eat 1 ¼ 2 ðcosh at 1Þ ¼ 2þ 2 2 a a a Another Method By lines 11 and 14 of Table 16-1, " # ð 2 2 t sinh a cosh a t 1 1 1=ðs a Þ l ¼ 2 ðcosh at 1Þ ¼ d ¼ s a a2 a 0 0

16.5

Find l

1

sþ1 sðs2 þ 4s þ 4Þ

Using the method of partial fractions, we have

Then and Hence,

sþ1 A B B2 ¼ þ 1 þ s s þ 2 ðs þ 2Þ2 sðs þ 2Þ2 s þ 1 1 s þ 1 1 A¼ ¼ ¼ ¼ B 2 s s¼2 2 ðs þ 2Þ2 s¼0 4 s þ 2 1 B1 ¼ ðs þ 2Þ ¼ 4 2sðs þ 2Þ2 s¼2 1 1 1 sþ1 1 1 4 1 4 1 2 þl þl ¼l l s sþ2 sðs2 þ 4s þ 4Þ ðs þ 2Þ2

The corresponding time functions are found in Table 16-1: sþ1 1 1 1 l1 ¼ e2t þ te2t 4 4 2 sðs2 þ 4s þ 4Þ

407

408

16.6

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

In the series RC circuit of Fig. 16-5, the capacitor has an initial charge 2.5 mC. At t ¼ 0, the switch is closed and a constant-voltage source V ¼ 100 V is applied. Use the Laplace transform method to ﬁnd the current. The time-domain equation for the given circuit after the switch is closed is ðt 1 RiðtÞ þ Q0 þ iðÞ d ¼ V C 0 or

10iðtÞ þ

ðt 1 3 ð2:5 10 Þ þ iðÞ d ¼V 50 106 0

(6)

Q0 is opposite in polarity to the charge which the source will deposit on the capacitor. Taking the Laplace transform of the terms in (6), we obtain the s-domain equation 10IðsÞ

or

2:5 103 IðsÞ 100 þ ¼ 6 6 s 50 10 s 50 10 s IðsÞ ¼

15 s þ ð2 103 Þ

(7)

The time function is now obtained by taking the inverse Laplace transform of (7): 3 15 ¼ 15e210 t ðAÞ iðtÞ ¼ l1 s þ ð2 103 Þ

Fig. 16-5

16.7

ð8Þ

Fig. 16-6

In the RL circuit shown in Fig. 16-6, the switch is in position 1 long enough to establish steadystate conditions, and at t ¼ 0 it is switched to position 2. Find the resulting current. Assume the direction of the current as shown in the diagram. i0 ¼ 50=25 ¼ 2 A. The time-domain equation is 25i þ 0:01

The initial current is then

di ¼ 100 dt

ð9Þ

Taking the Laplace transform of (9), 25IðsÞ þ 0:01sIðsÞ 0:01ið0þ Þ ¼ 100=s

ð10Þ

25IðsÞ þ 0:01sIðsÞ þ 0:01ð2Þ ¼ 100=s

ð11Þ

Substituting for ið0þ Þ,

and

IðsÞ ¼

100 0:02 104 2 ¼ sð0:01s þ 25Þ 0:01s þ 25 sðs þ 2500Þ s þ 2500

(12)

CHAP. 16]

409

THE LAPLACE TRANSFORM METHOD

Applying the method of partial fractions, 104 A B ¼ þ sðs þ 2500Þ s s þ 2500 104 104 A¼ ¼ 4 and B ¼ ¼ 4 s þ 2500 s¼0 s s¼2500

with

Then,

IðsÞ ¼

ð13Þ

4 4 2 4 6 ¼ s s þ 2500 s þ 2500 s s þ 2500

(14)

Taking the inverse Laplace transform of (14), we obtain i ¼ 4 6e2500t (A).

16.8

In the series RL circuit of Fig. 16-7, an exponential voltage v ¼ 50e100t (V) is applied by closing the switch at t ¼ 0. Find the resulting current. The time-domain equation for the given circuit is Ri þ L

di ¼v dt

ð15Þ

In the s-domain, (15) has the form RIðsÞ þ sLIðsÞ Lið0þ Þ ¼ VðsÞ

ð16Þ

Substituting the circuit constants and the transform of the source, VðsÞ ¼ 50=ðs þ 100Þ, in (16), 10IðsÞ þ sð0:2ÞIðsÞ ¼

5 s þ 100

or

IðsÞ ¼

250 ðs þ 100Þðs þ 50Þ

ð17Þ

By the Heaviside expansion formula, l1 ½IðsÞ ¼ l1

X Pðan Þ a t PðsÞ ¼ en QðsÞ Q 0 ðan Þ n¼1:2

Here, PðsÞ ¼ 250, QðsÞ ¼ s2 þ 150s þ 5000, Q 0 ðsÞ ¼ 2s þ 150, a1 ¼ 100, and a2 ¼ 50. i ¼ l1 ½IðsÞ ¼

16.9

250 100t 250 50t e e þ ¼ 5e100t þ 5e50t 50 50

Then,

ðAÞ

The series RC circuit of Fig. 16-8 has a sinusoidal voltage source v ¼ 180 sin ð2000t þ Þ (V) and an initial charge on the capacitor Q0 ¼ 1:25 mC with polarity as shown. Determine the current if the switch is closed at a time corresponding to ¼ 908.

Fig. 16-7

Fig. 16-8

Fig. 16-9

The time-domain equation of the circuit is 40iðtÞ þ

ðt 1 3 ð1:25 10 Þ þ iðÞ d ¼ 180 cos 2000t 25 106 0

ð18Þ

410

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

The Laplace transform of (18) gives the s-domain equation 40IðsÞ þ

or

1:25 103 4 104 180s IðsÞ ¼ 2 þ s 25 106 s s þ 4 106

ð19Þ

4:5s2 1:25 þ 4 106 Þðs þ 103 Þ s þ 103

(20)

IðsÞ ¼

ðs2

Applying the Heaviside expansion formula to the ﬁrst term on the right in (20), we have PðsÞ ¼ 4:5s2 , QðsÞ ¼ s3 þ 103 s2 þ 4 106 s þ 4 109 , Q 0 ðsÞ ¼ 3s2 þ 2 103 s þ 4 106 , a1 ¼ j2 103 , a2 ¼ j2 103 , and a3 ¼ 103 . Then, i¼

3 Pðj2 103 Þ j2103 t Pð j2 103 Þ j2103 t Pð103 Þ 103 t þ 0 þ 0 1:25e10 t e e e 0 3 3 Q ðj 10 Þ Q ð j2 10 Þ Q ð103 Þ 3

3

¼ ð1:8 j0:9Þej210 t þ ð1:8 þ j0:9Þe j210 t 0:35e10

3

t

ð21Þ

103 t

¼ 1:8 sin 2000t þ 3:6 cos 2000t 0:35e ¼ 4:02 sin ð2000t þ 116:68Þ 0:35e10

3

t

ðAÞ

At t ¼ 0, the current is given by the instantaneous voltage, consisting of the source voltage and the charged capacitor voltage, divided by the resistance. Thus, !, 1:25 103 i0 ¼ 180 sin 908 40 ¼ 3:25 A 25 106 The same result is obtained if we set t ¼ 0 in (21).

16.10 In the series RL circuit of Fig. 16-9, the source is v ¼ 100 sin ð500t þ Þ (V). resulting current if the switch is closed at a time corresponding to ¼ 0.

Determine the

The s-domain equation of a series RL circuit is RIðsÞ þ sLIðsÞ Lið0þ Þ ¼ VðsÞ

ð22Þ

The transform of the source with ¼ 0 is VðsÞ ¼

ð100Þð500Þ s2 þ ð500Þ2

Since there is no initial current in the inductance, Lið0þ Þ ¼ 0. Substituting the circuit constants into (22), 5IðsÞ þ 0:01sIðsÞ ¼

5 104 s2 þ 25 104

or

IðsÞ ¼

5 106 ðs2 þ 25 104 Þðs þ 500Þ

ð23Þ

Expanding (23) by partial fractions, 1 þ j 1 j 10 IðsÞ ¼ 5 þ5 þ s þ j500 s j500 s þ 500

ð24Þ

The inverse Laplace transform of (24) is i ¼ 10 sin 500t 10 cos 500t þ 10e500t ¼ 10e500t þ 14:14 sin ð500t 458Þ

ðAÞ

16.11 Rework Problem 16.10 by writing the voltage function as v ¼ 100e j500t

ðVÞ

ð25Þ

Now VðsÞ ¼ 100=ðs j500Þ, and the s-domain equation is 5IðsÞ þ 0:01sIðsÞ ¼

100 s j500

or

IðsÞ ¼

104 ðs j500Þðs þ 500Þ

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

411

Using partial fractions, IðsÞ ¼

10 j10 10 þ j10 þ s j500 s þ 500

and inverting, i ¼ ð10 j10Þe j500t þ ð10 þ j10Þe500t ¼ 14:14e jð500t=4Þ þ ð10 þ j10Þe500t

ðAÞ

ð26Þ

The actual voltage is the imaginary part of (25); hence the actual current is the imaginary part of (26). i ¼ 14:14 sin ð500t =4Þ þ 10e500t

ðAÞ

16.12 In the series RLC circuit shown in Fig. 16-10, there is no initial charge on the capacitor. If the switch is closed at t ¼ 0, determine the resulting current. The time-domain equation of the given circuit is di 1 Ri þ L þ dt C

ðt iðÞ d ¼ V

ð27Þ

1 V ¼ IðsÞ sC s

ð28Þ

0

Because ið0þ Þ ¼ 0, the Laplace transform of (27) is RIðsÞ þ sLIðsÞ þ

or

2IðsÞ þ 1sIðsÞ þ

Hence,

IðsÞ ¼

1 50 IðsÞ ¼ 0:5s s

(29)

50 50 ¼ s2 þ 2s þ 2 ðs þ 1 þ jÞðs þ 1 jÞ

(30)

Expanding (30) by partial fractions, IðsÞ ¼

j25 j25 ðs þ 1 þ jÞ ðs þ 1 jÞ

ð31Þ

and the inverse Laplace transform of (31) gives i ¼ j25feð1jÞt eð1þjÞt g ¼ 50et sin t

Fig. 16-10

ðAÞ

Fig. 16-11

16.13 In the two-mesh network of Fig. 16-11, the two loop currents are selected as shown. Write the sdomain equations in matrix form and construct the corresponding circuit. Writing the set of equations in the time domain, ðt 1 di 5i1 þ Q0 þ i1 ðÞd þ 5i2 ¼ and 10i2 þ 2 2 þ 5i1 ¼ 2 dt 0 Taking the Laplace transform of (32) to obtain the corresponding s-domain equations,

ð32Þ

412

THE LAPLACE TRANSFORM METHOD

5I1 ðsÞ þ

Q0 1 þ I ðsÞ þ 5I2 ðsÞ ¼ VðsÞ 2s 2s 1

[CHAP. 16

10I2 ðsÞ þ 2sI2 ðsÞ 2i2 ð0þ Þ þ 5I1 ðsÞ ¼ VðsÞ

ð33Þ

When this set of s-domain equations is written in matrix form, 5 þ ð1=2sÞ 5 VðsÞ ðQ0 =2sÞ I1 ðsÞ ¼ þ VðsÞ þ 2i2 ð0 Þ 5 10 þ 2s I2 ðsÞ the required s-domain circuit can be determined by examination of the ZðsÞ, IðsÞ, and VðsÞ matrices (see Fig. 16-12).

Fig. 16-12

Fig. 16-13

16.14 In the two-mesh network of Fig. 16-13, ﬁnd the currents which result when the switch is closed. The time-domain equations for the network are di1 di 0:02 2 ¼ 100 dt dt di2 di1 0:02 þ 5i2 0:02 ¼0 dt dt

10i1 þ 0:02

ð34Þ

Taking the Laplace transform of set (34), ð10 þ 0:02sÞI1 ðsÞ 0:02sI2 ðsÞ ¼ 100=s

ð5 þ 0:02sÞI2 ðsÞ 0:02sI1 ðsÞ ¼ 0

ð35Þ

From the second equation in set (35) we ﬁnd I2 ðsÞ ¼ I1 ðsÞ

s s þ 250

ð36Þ

which when substituted into the ﬁrst equation gives s þ 250 10 3:33 I1 ðsÞ ¼ 6:67 ¼ sðs þ 166:7Þ s s þ 166:7

ð37Þ

Inverting (37), i1 ¼ 10 3:33e166:7t Finally, substitute (37) into (36) and obtain 1 I2 ðsÞ ¼ 6:67 s þ 166:7

whence

ðAÞ

i2 ¼ 6:67e166:7t

ðAÞ

16.15 Apply the initial- and ﬁnal-value theorems in Problem 16.14. The initial value of i1 is given by s þ 250 i1 ð0þ Þ ¼ lim ½sI1 ðsÞ ¼ lim 6:667 ¼ 6:67 A s!1 s!1 s þ 166:7

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

413

and the ﬁnal value is s þ 250 i1 ð1Þ ¼ lim½sI1 ðsÞ ¼ lim 6:67 ¼ 10 A s!0 s!0 s þ 166:7 The initial value of i2 is given by i2 ð0þ Þ ¼ lim ½sI2 ðsÞ ¼ lim 6:667 s!1

s!1

s ¼ 6:67 A s þ 166:7

and the ﬁnal value is s i2 ð1Þ ¼ lim½sI2 ðsÞ ¼ lim 6:67 ¼0 s!0 s!0 s þ 166:7 Examination of Fig. 16-13 veriﬁes each of the preceding initial and ﬁnal values. At the instant of closing, the inductance presents an inﬁnite impedance and the currents are i1 ¼ i2 ¼ 100=ð10 þ 5Þ ¼ 6:67 A. Then, in the steady state, the inductance appears as a short circuit; hence, i1 ¼ 10 A, i2 ¼ 0.

16.16 Solve for i1 in Problem 16.14 by determining an equivalent circuit in the s-domain. In the s-domain the 0.02-H inductor has impedance ZðsÞ ¼ 0:02s. Therefore, the equivalent impedance of the network as seen from the source is ð0:02sÞð5Þ s þ 166:7 ZðsÞ ¼ 10 þ ¼ 15 0:02s þ 5 s þ 250 and the s-domain equivalent circuit is as shown in Fig. 16-14. The current is then VðsÞ 100 s þ 250 s þ 250 I1 ðsÞ ¼ ¼ ¼ 6:67 ZðsÞ s 15ðs þ 166:7Þ sðs þ 166:7Þ This expression is identical with (37) of Problem 16.14, and so the same time function i1 is obtained.

Fig. 16-14

Fig. 16-15

16.17 In the two-mesh network shown in Fig. 16-15 there is no initial charge on the capacitor. Find the loop currents i1 and i2 which result when the switch is closed at t ¼ 0. The time-domain equations for the circuit are 10i1 þ

1 0:2

ðt i1 d þ 10i2 ¼ 50

50i2 þ 10i1 ¼ 50

0

The corresponding s-domain equations are 1 50 50 I ðsÞ þ 10I2 ðsÞ ¼ 50I2 ðsÞ þ 10I1 ðsÞ ¼ 0:2s 1 s s 5 1 1 I2 ðsÞ ¼ I1 ðsÞ ¼ s þ 0:625 s s þ 0:625

10I1 ðsÞ þ Solving,

414

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

which invert to i1 ¼ 5e0:625t

ðAÞ

i2 ¼ 1 e0:625t

ðAÞ

16.18 Referring to Problem 16.17, obtain the equivalent impedance of the s-domain network and determine the total current and the branch currents using the current-division rule. The s-domain impedance as seen by the voltage source is ZðsÞ ¼ 10 þ

40ð1=0:2sÞ 80s þ 50 s þ 5=8 ¼ ¼ 10 40 þ 1=0:2s 8s þ 1 s þ 1=8

ð38Þ

The equivalent circuit is shown in Fig. 16-16; the resulting current is IðsÞ ¼

VðsÞ s þ 1=8 ¼5 ZðsÞ sðs þ 5=8Þ

ð39Þ

Expanding IðsÞ in partial fractions, IðsÞ ¼

1 4 þ s s þ 5=8

from which

i ¼ 1 þ 4e5t=8

ðAÞ

Now the branch currents I1 ðsÞ and I2 ðsÞ can be obtained by the current-division rule. Referring to Fig. 16-17, we have 40 5 and i1 ¼ 5e0:625t ðAÞ ¼ I1 ðsÞ ¼ IðsÞ 40 þ 1=0:2s s þ 5=8 1=0:2s 1 1 and i2 ¼ 1 e0:625t ðAÞ I2 ðsÞ ¼ IðsÞ ¼ 40 þ 1=0:2s s s þ 5=8

Fig. 16-16

Fig. 16-17

16.19 In the network of Fig. 16-18 the switch is closed at t ¼ 0 and there is no initial charge on either of the capacitors. Find the resulting current i.

Fig. 16-18

CHAP. 16]

415

THE LAPLACE TRANSFORM METHOD

The network has an equivalent impedance in the s-domain ZðsÞ ¼ 10 þ

ð5 þ 1=sÞð5 þ 1=0:5sÞ 125s2 þ 45s þ 2 ¼ 10 þ 1=s þ 1=0:5s sð10s þ 3Þ

Hence, the current is IðsÞ ¼

VðsÞ 50 sð10s þ 3Þ 4ðs þ 0:3Þ ¼ ¼ ZðsÞ s ð125s2 þ 45s þ 2Þ ðs þ 0:308Þðs þ 0:052Þ

Expanding IðsÞ in partial fractions, IðsÞ ¼

1=8 31=8 þ s þ 0:308 s þ 0:052

and

i¼

1 0:308t 31 0:052t e e þ 8 8

ðaÞ

16.20 Apply the initial- and ﬁnal-value theorems to the s-domain current of Problem 16.19. 1 s 31 s þ ¼4A ið0þ Þ ¼ lim ½sIðsÞ ¼ lim s!1 s!1 8 s þ 0:308 8 s þ 0:052 1 s 31 s ið1Þ ¼ lim½sIðsÞ ¼ lim þ ¼0 s!0 s!0 8 s þ 0:308 8 s þ 0:052 Examination of Fig. 16-18 shows that initially the total circuit resistance is R ¼ 10 þ 5ð5Þ=10 ¼ 12:5 , and thus, ið0þ Þ ¼ 50=12:5 ¼ 4 A. Then, in the steady state, both capacitors are charged to 50 V and the current is zero.

Supplementary Problems 16.21

Find the Laplace transform of each of the following functions. ðaÞ ðbÞ Ans:

ðeÞ f ðtÞ ¼ cosh !t ð f Þ f ðtÞ ¼ eat sinh !t

See Table 16-1 ! ðs þ aÞ2 !2

ðaÞðeÞ ðfÞ

16.22

ðcÞ f ðtÞ ¼ eat sin !t ðdÞ f ðtÞ ¼ sinh !t

f ðtÞ ¼ At f ðtÞ ¼ teat

Find the inverse Laplace transform of each of the following functions. ðaÞ ðbÞ ðcÞ Ans:

s ðs þ 2Þðs þ 1Þ 1 FðsÞ ¼ 2 s þ 7s þ 12 5s FðsÞ ¼ 2 s þ 3s þ 2 FðsÞ ¼

ðaÞ ðbÞ ðcÞ

2e2t et 3t

e

e

2t

10e

3 þ 6s þ 9Þ sþ5 ðeÞ FðsÞ ¼ 2 s þ 2s þ 5 2s þ 4 ð f Þ FðsÞ ¼ 2 s þ 4s þ 13 ðdÞ

ðdÞ

4t

FðsÞ ¼

sðs2

1 1 3t 3 3e t

te3t

ðgÞ

ðgÞ

FðsÞ ¼

ðs2

10 29 cos 2t

2s þ 4Þðs þ 5Þ

5t 4 þ 29 sin 2t 10 29 e

ðeÞ e ðcos 2t þ 2 sin 2tÞ t

5e

ðfÞ

2e2t cos 3t

16.23

A series RL circuit, with R ¼ 10 and L ¼ 0:2 H, has a constant voltage V ¼ 50 V applied at t ¼ 0. Find the resulting current using the Laplace transform method. Ans: i ¼ 5 5e50t ðAÞ

16.24

In the series RL circuit of Fig. 16-19, the switch is in position 1 long enough to establish the steady state and is switched to position 2 at t ¼ 0. Find the current. Ans: i ¼ 5e50t ðAÞ

416

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

Fig. 16-19 16.25

In the circuit shown in Fig. 16-20, switch 1 is closed at t ¼ 0 and then, at t ¼ t 0 ¼ 4 ms, switch 2 is opened. Find the current in the intervals 0 < t < t 00 and t > t 0 . Ans: i ¼ 2ð1 e500t Þ A; i ¼ 1:06e1500ðtt Þ þ 0:667 ðA)

Fig. 16-20

Fig. 16-21

16.26

In the series RL circuit shown in Fig. 16-21, the switch is closed on position 1 at t ¼ 0 and then, at t ¼ t 0 ¼ 50 ms, it is moved to position 2. Find0 the current in the intervals 0 < t < t 0 and t > t 0 . Ans: i ¼ 0:1ð1 e2000t Þ ðAÞ; i ¼ 0:06e2000ðtt Þ 0:05 ðAÞ

16.27

A series RC circuit, with R ¼ 10 and C ¼ 4 mF, has an initial charge Q0 ¼ 800 mC on the capacitor at the time the switch is closed, applying a constant-voltage source V ¼ 100 V. Find the resulting current transient if the charge is (a) of the 3same polarity as that deposited by the source, and (b) of the opposite polarity. 3 Ans: ðaÞ i ¼ 10e2510 t ðAÞ; ðbÞ i ¼ 30e2510 t ðAÞ

16.28

A series RC circuit, with R ¼ 1 k and C ¼ 20 mF, has an initial charge Q0 on the capacitor at the time the switch is closed, applying a constant-voltage source V ¼ 50 V. If the resulting current is i ¼ 0:075e50t (A), ﬁnd the charge Q0 and its polarity. Ans: 500 mC, opposite polarity to that deposited by source

16.29

In the RC circuit shown in Fig. 16-22, the switch is closed on position 1 at t ¼ 0 and then, at t ¼ t 0 ¼ (the time constant) is moved to position 2. Find the transient current in the intervals 0 < t < t 0 and t > t 0 . 0 Ans: i ¼ 0:5e200t ðAÞ; i ¼ :0516e200ðtt Þ ðAÞ

Fig. 16-22

Fig. 16-23

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

417

16.30

In the circuit of Fig. 16-23, Q0 ¼4 300 mC at the time the switch is closed. transient. Ans: i ¼ 2:5e2:510 t (A)

16.31

In the circuit shown in Fig. 16-24, the capacitor has an initial charge Q0 ¼ 25 mC and the sinusoidal voltage source is v ¼ 100 sin ð1000t þ Þ (V). Find the resulting current if the switch is closed at a time corresponding to ¼ 308. Ans: i ¼ 0:1535e4000t þ 0:0484 sin ð1000t þ 1068Þ (A)

16.32

A series RLC circuit, with R ¼ 5 , L ¼ 0:1 H, and C ¼ 500 mF, has a constant voltage V ¼ 10 V applied at t ¼ 0. Find the resulting current. Ans: i ¼ 0:72e25t sin 139t (A)

Fig. 16-24

Find the resulting current

Fig. 16-25

16.33

In the series RLC circuit of Fig. 16-25, the capacitor has an initial charge Q0 ¼ 1 mC and the switch is in position 1 long enough to establish the steady state. Find the transient current which results when the switch is moved from position 1 to 2 at t ¼ 0. Ans: i ¼ e25t ð2 cos 222t 0:45 sin 222tÞ (A)

16.34

A series RLC circuit, with R ¼ 5 , L ¼ 0:2 H, and C ¼ 1 F has a voltage source v ¼ 10e100t (V) applied at t ¼ 0. Find the resulting current. Ans: i ¼ 0:666e100t þ 0:670e24:8t 0:004e0:2t (A)

16.35

A series RLC circuit, with R ¼ 200 , L ¼ 0:5 H, and C ¼ 100 mF has a sinusoidal voltage source v ¼ 300 sin ð500t þ Þ (V). Find the resulting current if the switch is closed at a time corresponding to ¼ 308. Ans: i ¼ 0:517e341:4t 0:197e58:6t þ 0:983 sin ð500t 198Þ (A)

16.36

A series RLC circuit, with R ¼ 5 , L ¼ 0:1 H, and C ¼ 500 mF has a sinusoidal voltage source v ¼ 100 sin 250t (V). Find the resulting current if the switch is closed at t ¼ 0. Ans: i ¼ e25t ð5:42 cos 139t þ 1:89 sin 139tÞ þ 5:65 sinð250t 73:68Þ (A)

16.37

In the two-mesh network of Fig. 16-26, the currents are selected as shown in the diagram. Write the timedomain equations, transform them5 into the corresponding s-domain equations, and obtain the currents i1 5 and i2 . Ans: i1 ¼ 2:5ð1 þ e10 t Þ ðAÞ, i2 ¼ 5e10 t (A)

Fig. 16-26

418

16.38

THE LAPLACE TRANSFORM METHOD

[CHAP. 16

For the two-mesh network shown in Fig. 16-27, ﬁnd the currents i1 and i2 which result when the switch is closed at t ¼ 0. Ans: i1 ¼ 0:101e100t þ 9:899e9950t (A), i2 ¼ 5:05e100t þ 5 þ 0:05e9950t (A)

Fig. 16-27

16.39

In the network shown in Fig. 16-28, the 100-V source passes a continuous current in the ﬁrst loop while the switch is open. Find the currents after the switch is closed at t ¼ 0. Ans: i1 ¼ 1:67e6:67t þ 5 (A), i2 ¼ 0:555e6:67t þ 5 (A)

16.40

The two-mesh network shown in Fig. 16-29 contains a sinusoidal voltage source v ¼ 100 sin ð200t þ Þ (V). The switch is closed at an instant when the voltage is increasing at its maximum rate. Find the resulting mesh currents, with directions as shown in the diagram. Ans: i1 ¼ 3:01e100t þ 8:96 sin ð200t 63:48Þ (A), i2 ¼ 1:505e100t þ 4:48 sin ð200t 63:48Þ (A)

Fig. 16-28

16.41

Fig. 16-29

In the circuit of Fig. 16-30, vð0Þ ¼ 1:2 V and ið0Þ ¼ 0:4 A. Ans:

Find v and i for t > 0.

v ¼ 1:3334et 0:1334e2:5t ; t > 0 i ¼ 0:66667et 0:2667e2:5t ; t > 0

Fig. 16-30

16.42

In the circuit of Fig. 16-31, ig ðtÞ ¼ cos tuðtÞ. Ans:

v ¼ 0:8305 cos ðt 48:48Þ; t > 0 i ¼ 0:2626 cos ðt 66:88Þ; t > 0

Fig. 16-31

Find v and i.

CHAP. 16]

THE LAPLACE TRANSFORM METHOD

16.43

In the circuit of Fig. 16-31, ig ¼

1A cos t

t<0 . Find v and i for t > 0 and compare with results of Problems t>0

16.41 and 16.42. Ans:

v ¼ 0:6667et 0:0185e2:5t þ 0:8305 cos ðt 48:48Þ; t > 0 i ¼ 0:3332et 0:0368e2:5t þ 0:2626 cos ðt 66:88Þ; t > 0

16.44

Find capacitor voltage vðtÞ in the circuit shown in Fig. 16-32. Ans: v ¼ 20 10:21e4t cos ð4:9t þ 11:538Þ; t > 0

Fig. 16-32

16.45

419

Find inductor current iðtÞ in the circuit shown in Fig. 16-32. Ans: i ¼ 10 6:45e4t cos ð4:9t 39:28Þ; t > 0

Fourier Method of Waveform Analysis 17.1

INTRODUCTION

In the circuits examined previously, the response was obtained for excitations having constant, sinusoidal, or exponential form. In such cases a single expression described the forcing function for all time; for instance, v ¼ constant or v ¼ V sin !t, as shown in Fig. 17-1(a) and (b).

Fig. 17-1

Certain periodic waveforms, of which the sawtooth in Fig. 17-1(c) is an example, can be only locally deﬁned by single functions. Thus, the sawtooth is expressed by f ðtÞ ¼ ðV=TÞt in the interval 0 < t < T and by f ðtÞ ¼ ðV=TÞðt TÞ in the interval T < t < 2T. While such piecemeal expressions describe the waveform satisfactorily, they do not permit the determination of the circuit response. Now, if a periodic function can be expressed as the sum of a ﬁnite or inﬁnite number of sinusoidal functions, the responses of linear networks to nonsinusoidal excitations can be determined by applying the superposition theorem. The Fourier method provides the means for solving this type of problem. In this chapter we develop tools and conditions for such expansions. Periodic waveforms may be expressed in the form of Fourier series. Nonperiodic waveforms may be expressed by their Fourier transforms. However, a piece of a nonperiodic waveform speciﬁed over a ﬁnite time period may also be expressed by a Fourier series valid within that time period. Because of this, the Fourier series analysis is the main concern of this chapter. 420 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

CHAP. 17]

17.2

FOURIER METHOD OF WAVEFORM ANALYSIS

421

TRIGONOMETRIC FOURIER SERIES

Any periodic waveform—that is, one for which f ðtÞ ¼ f ðt þ TÞ—can be expressed by a Fourier series provided that (1)

If it is discontinuous, there are only a ﬁnite number of discontinuities in the period T;

(2) (3)

It has a ﬁnite average value over the period T; It has a ﬁnite number of positive and negative maxima in the period T.

When these Dirichlet conditions are satisﬁed, the Fourier series exists and can be written in trigonometric form: f ðtÞ ¼ 12 a0 þ a1 cos !t þ a2 cos 2t þ a3 cos 3!t þ þ b1 sin !t þ b2 sin 2!t þ b3 sin 3!t þ

ð1Þ

The Fourier coeﬃcients, a’s and b’s, are determined for a given waveform by the evaluation integrals. We obtain the cosine coeﬃcient evaluation integral by multiplying both sides of (1) by cos n!t and integrating over a full period. The period of the fundamental, 2=!, is the period of the series since each term in the series has a frequency which is an integral multiple of the fundamental frequency. ð 2=!

ð 2=! f ðtÞ cos n!t dt ¼ 0

0

1 a cos n!t dt þ 2 0

ð 2=!

þ

ð 2=! a1 cos !t cos n!t dt þ 0

an cos2 n!t dt þ þ

ð 2=!

0 ð 2=!

b1 sin !t cos n!t dt 0

b2 sin 2!t cos n! dt þ

þ

ð2Þ

0

The deﬁnite integrals on the right side of (2) are all zero except that involving cos2 n!t, which has the value ð=!Þan . Then an ¼

!

ð 2=! f ðtÞ cos n!t dt ¼ 0

2 T

ðT f ðtÞ cos 0

2nt dt T

ð3Þ

Multiplying (1) by sin n!t and integrating as above results in the sine coeﬃcient evaluation integral. ! bn ¼

ð 2=! 0

2 f ðtÞ sin n!t dt ¼ T

ðT f ðtÞ sin 0

An alternate form of the evaluation integrals with the variable 2 radians is an ¼ bn ¼

1 1

2nt dt T

ð4Þ

¼ !t and the corresponding period

ð 2 Fð Þ cos n d

ð5Þ

Fð Þ sin n d

ð6Þ

0 ð 2 0

where Fð Þ ¼ f ð =!Þ. The integrations can be carried out from T=2 to T=2, to þ, or over any other full period that might simplify the calculation. The constant a0 is obtained from (3) or (5) with n ¼ 0; however, since 12 a0 is the average value of the function, it can frequently be determined by inspection of the waveform. The series with coeﬃcients obtained from the above evaluation integrals converges uniformly to the function at all points of continuity and converges to the mean value at points of discontinuity.

422

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

EXAMPLE 17.1 Find the Fourier series for the waveform shown in Fig. 17-2.

Fig. 17-2 The waveform is periodic, of period 2=! in t or 2 in !t. It is continuous for 0 < !t < 2 and given therein by f ðtÞ ¼ ð10=2Þ!t, with discontinuities at !t ¼ n2 where n ¼ 0; 1; 2; . . . . The Dirichlet conditions are satisﬁed. The average value of the function is 5, by inspection, and thus, 12 a0 ¼ 5. For n > 0, (5) gives an ¼

1

ð 2 0

2 10 10 !t 1 !t cos n!t dð!tÞ ¼ 2 sin n!t þ 2 cos n!t 2 2 n n 0

10 ¼ 2 2 ðcos n2 cos 0Þ ¼ 0 2 n Thus, the series contains no cosine terms. 1 bn ¼

Using (6), we obtain

ð 2 0

2 10 10 !t 1 10 !t sin n!t dð!tÞ ¼ 2 cos n!t þ 2 sin n!t ¼ 2 n n 2 n 0

Using these sine-term coeﬃcients and the average term, the series is

f ðtÞ ¼ 5

1 10 10 10 10 X sin n!t sin !t sin 2!t sin 3!t ¼ 5 2 3 n¼1 n

The sine and cosine terms of like frequency can be combined as a single sine or cosine term with a phase angle. Two alternate forms of the trigonometric series result. f ðtÞ ¼ 12 a0 þ

and

f ðtÞ ¼ 12 a0 þ

P

cn cos ðn!t n Þ

X

cn sin ðn!t þ n Þ

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ where cn ¼ a2n þ b2n , n ¼ tan1 ðbn =an Þ, and n ¼ tan1 ðan =bn Þ. amplitude, and the harmonic phase angles are n or n .

17.3

ð7Þ

(8)

In (7) and (8), cn is the harmonic

EXPONENTIAL FOURIER SERIES

A periodic waveform f ðtÞ satisfying the Dirichlet conditions can also be written as an exponential Fourier series, which is a variation of the trigonometric series. The exponential series is f ðtÞ ¼

1 X

An e jn!t

ð9Þ

n¼1

To obtain the evaluation integral for the An coeﬃcients, we multiply (9) on both sides by ejn!t and integrate over the full period:

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

ð 2 f ðtÞe

jn!t

ð 2 dð!tÞ ¼ þ

0

A2 e 0 ð 2

þ 0 ð 2

þ

j2!t jn!t

e

ð 2 dð!tÞ þ

A0 ejn!t dð!tÞ þ

ð 2

423

A1 ej!t ejn!t dð!tÞ

0

A1 e j!t ejn!t dð!tÞ þ

0

An e jn!t ejn!t dð!tÞ þ

ð10Þ

0

Ð 2 The deﬁnite integrals on the right side of (10) are all zero except 0 An dð!tÞ, which has the value 2An . Then ð ð 1 2 1 T jn!t An ¼ f ðtÞe dð!tÞ or An ¼ f ðtÞej2nt=T dt ð11Þ 2 0 T 0 Just as with the an and bn evaluation integrals, the limits of integration in (11) may be the endpoints of any convenient full period and not necessarily 0 to 2 or 0 to T. Note that, f ðtÞ being real, An ¼ An , so that only positive n needed to be considered in (11). Furthermore, we have an ¼ 2 Re An

bn ¼ 2 Im An

ð12Þ

EXAMPLE 17.2 Derive the exponential series (9) from the trigonometric series (1). Replace the sine and cosine terms in (1) by their complex exponential equivalents. sin n!t ¼

e jn!t ejn!t 2j

cos n!t ¼

e jn!t þ ejn!t 2

Arranging the exponential terms in order of increasing n from 1 to þ1, we obtain the inﬁnite sum (9) where A0 ¼ a0 =2 and An ¼ 12 ðan jbn Þ

An ¼ 12 ðan þ jbn Þ

for n ¼ 1; 2; 3; . . .

EXAMPLE 17.3 Find the exponential Fourier series for the waveform shown in Fig. 17-2. Using the coeﬃcients of this exponential series, obtain an and bn of the trigonometric series and compare with Example 17.1. In the interval 0 < !t < 2 the function is given by f ðtÞ ¼ ð10=2Þ!t. By inspection, the average value of the function is A0 ¼ 5. Substituting f ðtÞ in (11), we obtain the coeﬃcients An . 2 ð 1 2 10 10 ejn!t 10 An ¼ ðjn!t 1Þ ¼j !tejn!t dð!tÞ ¼ 2 0 2 2n ð2Þ2 ðjnÞ2 0 Inserting the coeﬃcients An in (12), the exponential form of the Fourier series for the given waveform is f ðtÞ ¼ j

10 j2!t 10 j!t 10 j!t 10 j2!t j þ5þj þ e e e þj e 4 2 2 4

ð13Þ

The trigonometric series coeﬃcients are, by (12), 10 n 10 10 10 sin !t sin 2!t sin 3!t f ðtÞ ¼ 5 2 3 an ¼ 0

and so

bn ¼

which is the same as in Example 17.1.

17.4

WAVEFORM SYMMETRY

The series obtained in Example 17.1 contained only sine terms in addition to a constant term. Other waveforms will have only cosine terms; and sometimes only odd harmonics are present in the series, whether the series contains sine, cosine, or both types of terms. This is the result of certain types of

424

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

symmetry exhibited by the waveform. Knowledge of such symmetry results in reduced calculations in determining the Fourier series. For this reason the following deﬁnitions are important. 1.

A function f ðxÞ is said to be even if f ðxÞ ¼ f ðxÞ. The function f ðxÞ ¼ 2 þ x2 þ x4 is an example of even functions since the functional values for x and x are equal. The cosine is an even function, since it can be expressed as the power series cos x ¼ 1

x2 x4 x6 x8 þ þ 2! 4! 6! 8!

The sum or product of two or more even functions is an even function, and with the addition of a constant the even nature of the function is still preserved. In Fig. 17-3, the waveforms shown represent even functions of x. They are symmetrical with respect to the vertical axis, as indicated by the construction in Fig. 17-3(a).

Fig. 17-3

2. A function f ðxÞ is said to be odd if f ðxÞ ¼ f ðxÞ. The function f ðxÞ ¼ x þ x3 þ x5 is an example of odd functions since the values of the function for x and x are of opposite sign. The sine is an odd function, since it can be expressed as the power series sin x ¼ x

x3 x5 x7 x9 þ þ 3! 5! 7! 9!

The sum of two or more odd functions is an odd function, but the addition of a constant removes the odd nature of the function. The product of two odd functions is an even function. The waveforms shown in Fig. 17-4 represent odd functions of x. They are symmetrical with respect to the origin, as indicated by the construction in Fig. 17-4(a).

Fig. 17-4

Fig. 17-5

CHAP. 17]

3.

FOURIER METHOD OF WAVEFORM ANALYSIS

425

A periodic function f ðxÞ is said to have half-wave symmetry if f ðxÞ ¼ f ðx þ T=2Þ where T is the period. Two waveforms with half-wave symmetry are shown in Fig. 17-5.

When the type of symmetry of a waveform is established, the following conclusions are reached. If the waveform is even, all terms of its Fourier series are cosine terms, including a constant if the waveform has a nonzero average value. Hence, there is no need of evaluating the integral for the coeﬃcients bn , since no sine terms can be present. If the waveform is odd, the series contains only sine terms. The wave may be odd only after its average value is subtracted, in which case its Fourier representation will simply contain that constant and a series of sine terms. If the waveform has half-wave symmetry, only odd harmonics are present in the series. This series will contain both sine and cosine terms unless the function is also odd or even. In any case, an and bn are equal to zero for n ¼ 2; 4; 6; . . . for any waveform with half-wave symmetry. Half-wave symmetry, too, may be present only after subtraction of the average value.

Fig. 17-6

Fig. 17-7

Certain waveforms can be odd or even, depending upon the location of the vertical axis. The square wave of Fig. 17-6(a) meets the condition of an even function: f ðxÞ ¼ f ðxÞ. A shift of the vertical axis to the position shown in Fig. 17-6(b) produces an odd function f ðxÞ ¼ f ðxÞ. With the vertical axis placed at any points other than those shown in Fig. 17-6, the square wave is neither even nor odd, and its series contains both sine and cosine terms. Thus, in the analysis of periodic functions, the vertical axis should be conveniently chosen to result in either an even or odd function, if the type of waveform makes this possible. The shifting of the horizontal axis may simplify the series representation of the function. As an example, the waveform of Fig. 17-7(a) does not meet the requirements of an odd function until the average value is removed as shown in Fig. 17-7(b). Thus, its series will contain a constant term and only sine terms. The preceding symmetry considerations can be used to check the coeﬃcients of the exponential Fourier series. An even waveform contains only cosine terms in its trigonometric series, and therefore the exponential Fourier coeﬃcients must be pure real numbers. Similarly, an odd function whose trigonometric series consists of sine terms has pure imaginary coeﬃcients in its exponential series.

17.5

LINE SPECTRUM

A plot showing each of the harmonic amplitudes in the wave is called the line spectrum. The lines decrease rapidly for waves with rapidly convergent series. Waves with discontinuities, such as the sawtooth and square wave, have spectra with slowly decreasing amplitudes, since their series have strong

426

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

high harmonics. Their 10th harmonics will often have amplitudes of signiﬁcant value as compared to the fundamental. In contrast, the series for waveforms without discontinuities and with a generally smooth appearance will converge rapidly, and only a few terms are required to generate the wave. Such rapid convergence will be evident from the line spectrum where the harmonic amplitudes decrease rapidly, so that any above the 5th or 6th are insigniﬁcant. The harmonic content and the line spectrum of a wave are part of the very nature of that wave and never change, regardless of the method of analysis. Shifting the origin gives the trigonometric series a completely diﬀerent appearance, and the exponential series coeﬃcients also change greatly. However, the same harmonics always appear in the series, and their amplitudes, c0 ¼ j 12 a0 j or

c0 ¼ jA0 j

and

and

cn ¼

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ a2n þ b2n ðn 1Þ

cn ¼ jAn j þ jAn j ¼ 2jAn j

ðn 1Þ

ð14Þ (15)

remain the same. Note that when the exponential form is used, the amplitude of the nth harmonic combines the contributions of frequencies þn! and n!. EXAMPLE 17.4 In Fig. 17-8, the sawtooth wave of Example 17.1 and its line spectrum are shown. Since there were only sine terms in the trigonometric series, the harmonic amplitudes are given directly by 12 a0 and jbn j. The same line spectrum is obtained from the exponential Fourier series, (13).

Fig. 17-8

17.6

WAVEFORM SYNTHESIS

Synthesis is a combination of parts so as to form a whole. Fourier synthesis is the recombination of the terms of the trigonometric series, usually the ﬁrst four or ﬁve, to produce the original wave. Often it is only after synthesizing a wave that the student is convinced that the Fourier series does in fact represent the periodic wave for which it was obtained. The trigonometric series for the sawtooth wave of Fig. 17-8 is f ðtÞ ¼ 5

10 10 10 sin !t sin 2!t sin 3!t 2 3

These four terms are plotted and added in Fig. 17-9. Although the result is not a perfect sawtooth wave, it appears that with more terms included the sketch will more nearly resemble a sawtooth. Since this wave has discontinuities, its series is not rapidly convergent, and consequently, the synthesis using only four terms does not produce a very good result. The next term, at the frequency 4!, has amplitude 10/ 4, which is certainly signiﬁcant compared to the fundamental amplitude, 10/. As each term is added in the synthesis, the irregularities of the resultant are reduced and the approximation to the original wave is improved. This is what was meant when we said earlier that the series converges to the function at all points of continuity and to the mean value at points of discontinuity. In Fig. 17-9, at 0 and 2 it is clear that a value of 5 will remain, since all sine terms are zero at these points. These are the points of discontinuity; and the value of the function when they are approached from the left is 10, and from the right 0, with the mean value 5.

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

427

Fig. 17-9

17.7

EFFECTIVE VALUES AND POWER The eﬀective or rms value of the function

is

Frms

f ðtÞ ¼ 12 a0 þ a1 cos !t þ a2 cos 2!t þ þ b1 sin !t þ b2 sin 2!t þ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ¼ ð12 a0 Þ2 þ 12 a21 þ 12 a22 þ þ 12 b21 þ 12 b22 þ ¼ c20 þ 12 c21 þ 12 c22 þ 12 c33 þ

(16)

where (14) has been used. Considering a linear network with an applied voltage which is periodic, we would expect that the resulting current would contain the same harmonic terms as the voltage, but with harmonic amplitudes of diﬀerent relative magnitude, since the impedance varies with n!. It is possible that some harmonics would not appear in the current; for example, in a pure LC parallel circuit, one of the harmonic frequencies might coincide with the resonant frequency, making the impedance at that frequency inﬁnite. In general, we may write X X v ¼ V0 þ Vn sin ðn!t þ n Þ and i ¼ I0 þ In sin ðn!t þ n Þ ð17Þ with corresponding eﬀective values of qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Vrms ¼ V02 þ 12 V12 þ 12 V22 þ

and

Irms ¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ I02 þ 12 I12 þ 12 I22 þ

ð18Þ

The average power P follows from integration of the instantaneous power, which is given by the product of v and i: h ih i X X p ¼ vi ¼ V0 þ Vn sin ðn!t þ n Þ I0 þ In sin ðn!t þ n Þ ð19Þ Since v and i both have period T, their product must have an integral number of its periods in T. (Recall that for a single sine wave of applied voltage, the product vi has a period half that of the voltage wave.) The average may therefore be calculated over one period of the voltage wave: ð ih i X X 1 Th P¼ V0 þ Vn sin ðn!t þ n Þ I0 þ In sin ðn!t þ n Þ dt ð20Þ T 0 Examination of the possible terms in the product of the two inﬁnite series shows them to be of the following types: the product of two constants, the product of a constant and a sine function, the product of two sine functions of diﬀerent frequencies, and sine functions squared. After integration, the product of the two constants is still V0 I0 and the sine functions squared with the limits applied appear as ðVn In =2Þ cos ðn n Þ; all other products upon integration over the period T are zero. Then the average power is P ¼ V0 I0 þ 12 V1 I1 cos 1 þ 12 V2 I2 cos 2 þ 12 V3 I3 cos 3 þ

ð21Þ

428

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

where n ¼ n n is the angle on the equivalent impedance of the network at the angular frequency n!, and Vn and In are the maximum values of the respective sine functions. In the special case of a single-frequency sinusoidal voltage, V0 ¼ V2 ¼ V3 ¼ ¼ 0, and (21) reduces to the familiar P ¼ 12 V1 I1 cos 1 ¼ Veff Ieff cos Compare Section 10.2.

Also, for a dc voltage, V1 ¼ V2 ¼ V3 ¼ ¼ 0, and (21) becomes P ¼ V0 I0 ¼ VI

Thus, (21) is quite general. Note that on the right-hand side there is no term that involves voltage and current of diﬀerent frequencies. In regard to power, then, each harmonic acts independently, and P ¼ P0 þ P1 þ P2 þ 17.8

APPLICATIONS IN CIRCUIT ANALYSIS

It has already been suggested above that we could apply the terms of a voltage series to a linear network and obtain the corresponding harmonic terms of the current series. This result is obtained by superposition. Thus we consider each term of the Fourier series representing the voltage as a single source, as shown in Fig. 17.10. Now the equivalent impedance of the network at each harmonic frequency n! is used to compute the current at that harmonic. The sum of these individual responses is the total response i, in series form, to the applied voltage. EXAMPLE 17.5 A series RL circuit in which R ¼ 5 and L ¼ 20 mH (Fig. 17-11) has an applied voltage v ¼ 100 þ 50 sin !t þ 25 sin 3!t (V), with ! ¼ 500 rad/s. Find the current and the average power. Compute the equivalent impedance of the circuit at each frequency found in the voltage function. Then obtain the respective currents. At ! ¼ 0, Z0 ¼ R ¼ 5 and I0 ¼

V0 100 ¼ 20 A ¼ 5 R

At ! ¼ 500 rad/s, Z1 ¼ 5 þ jð500Þð20 103 Þ ¼ 5 þ j10 ¼ 11:15 63:48 and i1 ¼

V1;max 50 sinð!t 63:48Þ ¼ 4:48 sinð!t 63:48Þ sinð!t 1 Þ ¼ 11:15 Z1

ðAÞ

At 3! ¼ 1500 rad/s, Z3 ¼ 5 þ j30 ¼ 30:4 80:548 and i3 ¼

V3;max 25 sin ð3!t 80:548Þ ¼ 0:823 sin ð3!t 80:548Þ sin ð3!t 3 Þ ¼ 30:4 Z3

ðAÞ

The sum of the harmonic currents is the required total response; it is a Fourier series of the type (8). i ¼ 20 þ 4:48 sin ð!t 63:48Þ þ 0:823 sin ð3!t 80:548Þ

ðAÞ

This current has the eﬀective value qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Ieff ¼ 202 þ ð4:482 =2Þ þ ð0:8232 =2Þ ¼ 410:6 ¼ 20:25 A which results in a power in the 5- resistor of 2 R ¼ ð410:6Þ5 ¼ 2053 W P ¼ Ieff

As a check, we compute the total average power by calculating ﬁrst the power contributed by each harmonic and then adding the results. At ! ¼ 0: At ! ¼ 500 rad/s:

P0 ¼ V0 I0 ¼ 100ð20Þ ¼ 2000 W P1 ¼ 12 V1 I1 cos 1 ¼ 12 ð50Þð4:48Þ cos 63:48 ¼ 50:1 W

At 3! ¼ 1500 rad/s: Then,

P3 ¼ 12 V3 I3 cos 3 ¼ 12 ð25Þð0:823Þ cos 80:548 ¼ 1:69 W P ¼ 2000 þ 50:1 þ 1:69 ¼ 2052 W

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-10

429

Fig. 17-11

Another Method The Fourier series expression for the voltage across the resistor is vR ¼ Ri ¼ 100 þ 22:4 sin ð!t 63:48Þ þ 4:11 sin ð3!t 80:548Þ ðVÞ rﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 1 1 VReff ¼ 1002 þ ð22:4Þ2 þ ð4:11Þ2 ¼ 10 259 ¼ 101:3 V 2 2

and

2 =R ¼ ð10 259Þ=5 ¼ 2052 W. Then the power delivered by the source is P ¼ VReff

In Example 17.5 the driving voltage was given as a trigonometric Fourier series in t, and the computations were in the time domain. (The complex impedance was used only as a shortcut; Zn and n could have been obtained directly from R, L, and n!). If, instead, the voltage is represented by an exponential Fourier series, vðtÞ ¼

þ1 X

Vn e jn!t

1

then we have to do with a superposition of phasors Vn (rotating counterclockwise if n > 0, clockwise if n < 0), and so frequency-domain methods are called for. This is illustrated in Example 17.6. EXAMPLE 17.6 A voltage represented by the triangular wave shown in Fig. 17-12 is applied to a pure capacitor C. Determine the resulting current.

Fig. 17-12 In the interval < !t < 0 the voltage function is v ¼ Vmax þ ð27Vmax =Þ!t; and for 0 < !t < , v ¼ Vmax ð2Vmax =Þ!t. Then the coeﬃcients of the exponential series are determined by the evaluation integral Vn ¼

1 2

ð0

½Vmax þ ð2Vmax =Þ!tejn!t dð!tÞ þ

1 2

from which Vn ¼ 4Vmax =2 n2 for odd n, and Vn ¼ 0 for even n. The phasor current produced by Vn (n odd) is

ð 0

½Vmax ð2Vmax =Þ!tejn!t dð!tÞ

430

FOURIER METHOD OF WAVEFORM ANALYSIS

In ¼ with an implicit time factor e jn!t .

[CHAP. 17

Vn 4Vmax =2 n2 4Vmax !C ¼j ¼ Zn 1=jn!C 2 n

The resultant current is therefore iðtÞ ¼

þ1 X

In e jn!t ¼ j

1

þ1 jn!t 4Vmax !C X e 2 n 1

where the summation is over odd n only. The series could be converted to the trigonometric form and then synthesized to show the current waveform. However, this series is of the same form as the result in Problem 17.8, where the coeﬃcients are An ¼ jð2V=nÞ for odd n only. The sign here is negative, indicating that our current wave is the negative of the square wave of Problem 17.8 and has a peak value 2Vmax !C=.

17.9

FOURIER TRANSFORM OF NONPERIODIC WAVEFORMS A nonperiod waveform xðtÞ is said to satisfy the Dirichlet conditions if Ð þ1 (a) xðtÞ is absolutely integrable, 1 jxðtÞj dt < 1, and (b) the number of maxima and minima and the number of discontinuities of xðtÞ in every ﬁnite interval is ﬁnite.

For such a waveform, we can deﬁne the Fourier transform Xð f Þ by ð1 Xð f Þ ¼ xðtÞej2ft dt

ð22aÞ

1

where f is the frequency. The above integral is called the Fourier integral. called the inverse Fourier transform of Xð f Þ and is obtained from it by ð1 xðtÞ ¼ Xð f Þe j2ft df

The time function xðtÞ is

ð22bÞ

1

xðtÞ and Xð f Þ form a Fourier transform pair. Instead of f , the angular velocity ! ¼ 2f may also be used, in which case, (22a) and (22b) become, respectively, ð1 Xð!Þ ¼ xðtÞej!t dt ð23aÞ 1

and

xðtÞ ¼

1 2

ð1

Xð!Þe j!t d!

(23b)

1

EXAMPLE 17.7 Find the Fourier transform of xðtÞ ¼ eat uðtÞ, a > 0. Plot Xð f Þ for 1 < f < þ1. From (22a), the Fourier transform of xðtÞ is ð1 1 Xð f Þ ¼ eat ej2ft dt ¼ a þ j2f 0

ð24Þ

Xð f Þ is a complex function of a real variable. Its magnitude and phase angle, jXð f Þj and Xð f Þ, respectively, shown in Figs. 17-13(a) and (b), are given by 1 jXð f Þj ¼ pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 a þ 42 f 2 and

Xð f Þ ¼ tan1 ð2f =aÞ

ð25aÞ

(25b)

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

431

Fig. 17-13

Alternatively, Xð f Þ may be shown by its real and imaginary parts, Re ½Xð f Þ and Im ½Xð f Þ, as in Figs. 17-14(a) and (b). a a2 þ 42 f 2 2f Im ½Xð f Þ ¼ 2 a þ 42 f 2

Re ½Xð f Þ ¼

ð26aÞ ð26bÞ

Fig. 17-14

EXAMPLE 17.8

Find the Fourier transform of the square pulse 1 for T < t < T xðtÞ ¼ 0 otherwise

From (22a), ðT Xð f Þ ¼

ej2ft dt ¼

T

Because xðtÞ is even, Xð f Þ is real.

EXAMPLE 17.9

1 h j2f iT sin 2fT e ¼ T j2f f

ð27Þ

The transform pairs are plotted in Figs. 17-15(a) and (b) for T ¼ 12 s.

Find the Fourier transform of xðtÞ ¼ eat uðtÞ; a > 0. ð0 Xð f Þ ¼ 1

eat ej2ft dt ¼

1 a j2f

ð28Þ

432

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

Fig. 17-15

EXAMPLE 17.10 Find the inverse Fourier transform of Xð f Þ ¼ 2a=ða2 þ 42 f 2 Þ, a > 0. By partial fraction expansion we have Xð f Þ ¼

1 1 þ a þ j2f a j2f

ð29Þ

The inverse of each term in (29) may be derived from (24) and (28) so that xðtÞ ¼ eat uðtÞ þ eat uðtÞ ¼ eajtj

for all t

See Fig. 17-16.

Fig. 17-16

17.10

PROPERTIES OF THE FOURIER TRANSFORM

Some properties of the Fourier transform are listed in Table 17-1. Several commonly used transform pairs are given in Table 17-2.

17.11

CONTINUOUS SPECTRUM

jXð f Þj2 , as deﬁned in Section 17.9, is called the energy density or the spectrum of the waveform xðtÞ. Unlike the periodic functions, the energy content of a nonperiodic waveform xðtÞ at each frequency is zero. However, the energy content within a frequency band from f1 to f2 is

CHAP. 17]

433

FOURIER METHOD OF WAVEFORM ANALYSIS

Table 17-1 Fourier Transform Properties ð1 ð1 Time Domain xðtÞ ¼ Xð f Þe j2ft dt Frequency Domain Xð f Þ ¼ xðtÞej2ft dt 1

1

1.

xðtÞ real

Xð f Þ ¼ X ðf Þ

2.

xðtÞ even, xðtÞ ¼ xðtÞ

Xð f Þ ¼ Xðf Þ

3.

xðtÞ, odd, xðtÞ ¼ xðtÞ

Xð f Þ ¼ Xðf Þ

4.

XðtÞ

xðf Þ ð1

ð1 5.

Xð f Þ df

xð0Þ ¼

Xð0Þ ¼

xðtÞ dt

1

1

Yð f Þ ¼

1 Xð f =aÞ jaj

6.

yðtÞ ¼ xðatÞ

7.

yðtÞ ¼ txðtÞ

8.

yðtÞ ¼ xðtÞ

Yð f Þ ¼ Xðf Þ

9.

yðtÞ ¼ xðt t0 Þ

Yð f Þ ¼ ej2ft0 Xð f Þ

Yð f Þ ¼

Table 17-2

1 dXð f Þ j2 df

Fourier Transform Pairs

xðtÞ

Xð f Þ

1.

eat uðtÞ; a > 0

1 a þ j2f

2.

eajtj ; a > 0

2a a2 þ 42 f 2

3.

teat uðtÞ; a > 0

1 ða þ j2f Þ2

4.

expðt2 = 2 Þ

expðf 2 2 Þ

7.

1

ð f Þ

8.

ðtÞ

1

9.

sin 2f0 t

ð f f0 Þ ð f þ f0 Þ 2j

10.

cos 2f0 t

ð f f0 Þ þ ð f þ f0 Þ 2

5.

6.

434

FOURIER METHOD OF WAVEFORM ANALYSIS

ð f2 W ¼2

[CHAP. 17

jxð f Þj2 df

ð30Þ

f1

EXAMPLE 17.11 Find the spectrum of xðtÞ ¼ eat uðtÞ eat uðtÞ, a > 0, shown in Fig. 17-17.

Fig. 17-17 We have xðtÞ ¼ x1 ðtÞ x2 ðtÞ.

Since x1 ðtÞ ¼ eat uðtÞ and x2 ðtÞ ¼ eat uðtÞ, X1 ð f Þ ¼

Then

1 a þ j2f

X2 ð f Þ ¼

Xð f Þ ¼ X1 ð f Þ X2 ð f Þ ¼ jXð f Þj2 ¼

from which

1 a j2f

j4f a2 þ 42 f 2

162 f 2 ða2 þ 42 f 2 Þ2

EXAMPLE 17.12 Find and compare the energy contents W1 y2 ðtÞ ¼ eat uðtÞ eat uðtÞ, a > 0, within the band 0 to 1 Hz. Let a ¼ 200. From Examples 17.10 and 17.11, jY1 ð f Þj2 ¼

4a2 ða2 þ 42 f 2 Þ2

and

jY2 ð f Þj2 ¼

and

W2

of

y1 ðtÞ ¼ ejatj

and

162 f 2 ða2 þ 42 f 2 Þ2

Within 0 < f < 1 Hz, the spectra and energies may be approximated by jY1 ð f Þj2 4=a2 ¼ 104 J=Hz

and

W1 ¼ 2ð104 Þ J ¼ 200 mJ

jY2 ð f Þ2 j 107 f 2

and

W2 0

The preceding results agree with the observation that most of the energy in y1 ðtÞ is near the low-frequency region in contrast to y2 ðtÞ.

Solved Problems 17.1

Find the trigonometric Fourier series for the square wave shown in Fig. 17-18 and plot the line spectrum. In the interval 0 < !t < , f ðtÞ ¼ V; and for < !t < 2, f ðtÞ ¼ V. The average value of the wave is zero; hence, a0 =2 ¼ 0. The cosine coeﬃcients are obtained by writing the evaluation integral with the functions inserted as follows:

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-18

an ¼

1

¼0

435

Fig. 17-19

ð

ð 2 V cos n!t dð!tÞ þ

0

( 2 ) V 1 1 sin n!t sin n!t ðVÞ cos n!t dð!tÞ ¼ n n 0

for all n

Thus, the series contains no cosine terms. Proceeding with the evaluation integral for the sine terms, ð ð 2 1 V sin n!t dð!tÞ þ ðVÞ sin n!t dð!tÞ bn ¼ 0 ( 2 ) V 1 1 ¼ cos n!t þ cos n!t n n 0 ¼

V 2V ð cos n þ cos 0 þ cos n2 cos nÞ ¼ ð1 cos nÞ n n

Then bn ¼ 4V=n for n ¼ 1; 3; 5; . . . ; and bn ¼ 0 for n ¼ 2; 4; 6; . . . . f ðtÞ ¼

The series for the square wave is

4V 4V 4V sin !t þ sin 3!t þ sin 5!t þ 3 5

The line spectrum for this series is shown in Fig. 17-19. This series contains only odd-harmonic sine terms, as could have been anticipated by examination of the waveform for symmetry. Since the wave in Fig. 17-18 is odd, its series contains only sine terms; and since it also has half-wave symmetry, only odd harmonics are present.

17.2

Find the trigonometric Fourier series for the triangular wave shown in Fig. 17-20 and plot the line spectrum. The wave is an even function, since f ðtÞ ¼ f ðtÞ, and if its average value, V=2, is subtracted, it also has half-wave symmetry, that is, f ðtÞ ¼ f ðt þ Þ. For < !t < 0, f ðtÞ ¼ V þ ðV=Þ!t; and for 0 < !t < , f ðtÞ ¼ V ðV=Þ!t. Since even waveforms have only cosine terms, all bn ¼ 0. For n 1, ð ð 1 0 1 ½V þ ðV=Þ!t cos n!t dð!tÞ þ ½V ðV=Þ!t cos n!t dð!tÞ an ¼ 0 ð ð0 ð V !t !t cos n!t dð!tÞ þ ¼ cos n!t dð!tÞ cos n!t dð!tÞ 0 ( 0 ) V 1 !t 1 !t sin n!t sin n!t ¼ 2 cos n!t þ 2 cos n!t þ n n2 n 0 ¼

V 2V ½cos 0 cosðnÞ cos n þ cos 0 ¼ 2 2 ð1 cos nÞ 2 n2 n

As predicted from half-wave symmetry, the series contains only odd terms, since an ¼ 0 for n ¼ 2; 4; 6; . . . . For n ¼ 1; 3; 5; . . . ; an ¼ 4V=2 n2 . Then the required Fourier series is f ðtÞ ¼

V 4V 4V 4V þ cos !t þ cos 3!t þ cos 5!t þ 2 2 ð3Þ2 ð5Þ2

436

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

The coeﬃcients decrease as 1=n2 , and thus the series converges more rapidly than that of Problem 17.1. This fact is evident from the line spectrum shown in Fig. 17-21.

Fig. 17-20

17.3

Fig. 17-21

Find the trigonometric Fourier series for the sawtooth wave shown in Fig. 17-22 and plot the line spectrum. By inspection, the waveform is odd (and therefore has average value zero). Consequently the series will contain only sine terms. A single expression, f ðtÞ ¼ ðV=Þ!t, describes the wave over the period from to þ, and we will use these limits on our evaluation integral for bn . ð 1 V 1 !t 2V cos n!t ðcos nÞ ðV=Þ!t sin n!t dð!tÞ ¼ 2 2 sin n!t ¼ bn ¼ n n n As cos n is þ1 for even n and 1 for odd n, the signs of the coeﬃcients alternate. The required series is f ðtÞ ¼

2V fsin !t 12 sin 2!t þ 13 sin 3!t 14 sin 4!t þ g

The coeﬃcients decrease as 1=n, and thus the series converges slowly, as shown by the spectrum in Fig. 17-23. Except for the shift in the origin and the average term, this waveform is the same as in Fig. 17-8; compare the two spectra.

Fig. 17-22

17.4

Fig. 17-23

Find the trigonometric Fourier series for the waveform shown in Fig. 17-24 and sketch the line spectrum. In the interval 0 < !t < , f ðtÞ ¼ ðV=Þ!t; and for < !t < 2, f ðtÞ ¼ 0. By inspection, the average value of the wave is V=4. Since the wave is neither even nor odd, the series will contain both sine and cosine terms. For n > 0, we have

an ¼

1

ð ðV=Þ!t cos n!t dð!tÞ ¼ 0

V 1 !t V sin n!t cos n!t þ ¼ 2 2 ðcos n 1Þ n 2 n2 n 0

CHAP. 17]

437

FOURIER METHOD OF WAVEFORM ANALYSIS

When n is even, cos n 1 ¼ 0 and an ¼ 0. When n is odd, an ¼ 2V=ð2 n2 Þ. bn ¼

1

ð ðV=Þ!t sin n!t dð!tÞ ¼ 0

The bn coeﬃcients are

V 1 !t V V cos n!t ðcos nÞ ¼ ð1Þnþ1 sin n!t ¼ n n n 2 n2 0

Then the required Fourier series is f ðtÞ ¼

V 2V 2V 2V cos 3!t cos 5!t 2 cos !t 4 ð3Þ2 ð5Þ2 V V V sin 2!t þ sin 3!t þ sin !t 2 3

Fig. 17-24

Fig. 17-25

The even-harmonic amplitudes are given directly by jbn j, since therepare no even-harmonic cosine terms. ﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ However, the odd-harmonic amplitudes must be computed using cn ¼ a2n þ b2n . Thus, c1 ¼

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ ð2V=2 Þ2 þ ðV=Þ2 ¼ Vð0:377Þ

c3 ¼ Vð0:109Þ

c5 ¼ Vð0:064Þ

The line spectrum is shown in Fig. 17-25.

17.5

Find the trigonometric Fourier series for the half-wave-rectiﬁed sine wave shown in Fig. 17-26 and sketch the line spectrum. The wave shows no symmetry, and we therefore expect the series to contain both sine and cosine terms. Since the average value is not obtainable by inspection, we evaluate a0 for use in the term a0 =2. ð 1 V 2V V sin !t dð!tÞ ¼ ½ cos !t0 ¼ a0 ¼ 0 Next we determine an : ð 1 V sin !t cos n!t dð!tÞ 0 V n sin !t sin n!t cos n!t cos !t V ¼ ðcos n þ 1Þ ¼ n2 þ 1 ð1 n2 Þ 0

an ¼

With n even, an ¼ 2V=ð1 n2 Þ; and with n odd, an ¼ 0. However, this expression is indeterminate for n ¼ 1, and therefore we must integrate separately for a1 . ð ð 1 V 1 V sin !t cos !t dð!tÞ ¼ sin 2!t dð!tÞ ¼ 0 a1 ¼ 0 02 Now we evaluate bn : bn ¼

1

ð V sin !t sin n!t dð!tÞ ¼ 0

V n sin !t cos n!t sin n!t cos !t ¼0 n2 þ 1 0

438

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

Here again the expression is indeterminate for n ¼ 1, and b1 is evaluated separately. ð 1 V !t sin 2!t V V sin2 !t dð!tÞ ¼ ¼ b1 ¼ 0 2 4 2 0 Then the required Fourier series is V 2 2 2 1 þ sin !t cos 2!t cos 4!t cos 6!t f ðtÞ ¼ 2 3 15 35 The spectrum, Fig. 17-27, shows the strong fundamental term in the series and the rapidly decreasing amplitudes of the higher harmonics.

Fig. 17-26

17.6

Fig. 17-27

Find the trigonometric Fourier series for the half-wave-rectiﬁed sine wave shown in Fig. 17-28, where the vertical axis is shifted from its position in Fig. 17-26. The function is described in the interval < !t < 0 by f ðtÞ ¼ V sin !t. The average value is the same as that in Problem 17.5, that is, 12 a0 ¼ V=. For the coeﬃcients an , we have an ¼

1

ð0 ðV sin !tÞ cos n!t dð!tÞ ¼

V ð1 þ cos nÞ ð1 n2 Þ

Fig. 17-28 For n even, an ¼ 2V=ð1 n2 Þ; and for n odd, an ¼ 0, except that n ¼ 1 must be examined separately. ð 1 0 a1 ¼ ðV sin !tÞ cos !t dð!tÞ ¼ 0 For the coeﬃcients bn , we obtain bn ¼

1

ð0 ðV sin !tÞ sin n!t dð!tÞ ¼ 0

except for n ¼ 1. b1 ¼ Thus, the series is f ðtÞ ¼

1

ð0

ðVÞ sin2 !t dð!tÞ ¼

V 2

V 2 2 2 1 sin !t cos 2!t cos 4!t cos 6!t 2 3 15 35

CHAP. 17]

439

FOURIER METHOD OF WAVEFORM ANALYSIS

This series is identical to that of Problem 17.5, except for the fundamental term, which has a negative coeﬃcient in this series. The spectrum would obviously be identical to that of Fig. 17-27. Another Method When the sine wave V sin !t is subtracted from the graph of Fig. 17.26, the graph of Fig. 17-28 results.

17.7

Obtain the trigonometric Fourier series for the repeating rectangular pulse shown in Fig. 17-29 and plot the line spectrum.

Fig. 17-29

Fig. 17-30

With the vertical axis positioned as shown, the wave is even and the series will contain only cosine terms and a constant term. In the period from to þ used for the evaluation integrals, the function is zero except from =6 to þ=6. ð ð 1 =6 V 1 =6 2V n an ¼ sin a0 ¼ V dð!tÞ ¼ V cos n!t dð!tÞ ¼ =6 3 =6 n 6 pﬃﬃﬃ pﬃﬃﬃ Since sin n=6 ¼ 1=2, 3=2; 1; 3=2; 1=2; 0; 1=2; . . . for n ¼ 1; 2; 3; 4; 5; 6; 7; . . . , respectively, the series is " pﬃﬃﬃ pﬃﬃﬃ V 2V 1 1 3 1 3 1 f ðtÞ ¼ þ cos !t þ cos 2!t þ 1 cos 3!t þ cos 4!t 6 2 3 2 2 2 4 # 1 1 1 1 cos 5!t cos 7!t þ 2 5 2 7 or

f ðtÞ ¼

1 V 2V X 1 þ sin ðn=6Þ cos n!t 6 n¼1 n

The line spectrum, shown in Fig. 17-30, decreases very slowly for this wave, since the series converges very slowly to the function. Of particular interest is the fact that the 8th, 9th, and 10th harmonic amplitudes exceed the 7th. With the simple waves considered previously, the higher-harmonic amplitudes were progressively lower.

17.8

Find the exponential Fourier series for the square wave shown in Figs. 17-18 and 17-31, and sketch the line spectrum. Obtain the trigonometric series coeﬃcients from those of the exponential series and compare with Problem 17.1. In the interval < !t < 0, f ðtÞ ¼ V; and for 0 < !t < , f ðtÞ ¼ V. A0 ¼ 0 and the An will be pure imaginaries. ð 0 ð 1 ðVÞejn!t dð!tÞ þ Vejn!t dð!tÞ An ¼ 2 0 ( 0 ) V 1 1 jn!t jn!t ¼ þ e e 2 ðjnÞ ðjnÞ 0 ¼

The wave is odd; therefore,

V V jn ðe0 þ e jn þ ejn e0 Þ ¼ j ðe 1Þ j2n n

440

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

For n even, e jn ¼ þ1 and An ¼ 0; for n odd, e jn ¼ 1 and An ¼ jð2V=nÞ (half-wave symmetry). The required Fourier series is f ðtÞ ¼ þ j

2V j3!t 2V j!t 2V j!t 2V j3!t e e e j e þj j 3 3

The graph in Fig. 17-32 shows amplitudes for both positive and negative frequencies. Combining the values at þn and n yields the same line spectrum as plotted in Fig. 17-19.

Fig. 17-31

Fig. 71-32

The trigonometric-series cosine coeﬃcients are an ¼ 2 Re An ¼ 0 4V bn ¼ 2 Im An ¼ n

and

for odd n only

These agree with the coeﬃcients obtained in Problem 17.1.

17.9

Find the exponential Fourier series for the triangular wave shown in Figs. 17-20 and 17-33 and sketch the line spectrum. In the interval < !t < 0, f ðtÞ ¼ V þ ðV=Þ!t; and for 0 < !t < , f ðtÞ ¼ V ðV=Þ!t. The wave is even and therefore the An coeﬃcients will be pure real. By inspection the average value is V=2. 1 An ¼ 2

ð 0

jn!t

½V þ ðV=Þ!te

dð!tÞ þ

jn!t

½V ðV=Þ!te 0

dð!tÞ

ejn!t dð!tÞ 0 ( 0 jn!t ) jn!t V e e V ¼ 2 ðjn!t 1Þ ðjn!t 1Þ ¼ 2 2 ð1 e jn Þ 2 n 2 ðjnÞ2 ðjnÞ 0

¼

V 22

ð 0

ð

!tejn!t dð!tÞ þ

ð

ð!tÞejn!t dð!tÞ þ

For even n, e jn ¼ þ1 and An ¼ 0; for odd n, An ¼ 2V=2 n2 . f ðtÞ ¼ þ

ð

Thus the series is

2V 2V j!t V 2V j!t 2V j3!t ej3!t þ e þ þ 2e þ e þ 2 ðÞ ð3Þ2 ðÞ2 ð3Þ2

The harmonic amplitudes c0 ¼

V 2

are exactly as plotted in Fig. 17-21.

cn ¼ 2jAn j ¼

0 4V=2 n2

ðn ¼ 2; 4; 6; . . .Þ ðn ¼ 1; 3; 5; . . .Þ

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-33

441

Fig. 17-34

17.10 Find the exponential Fourier series for the half-wave rectiﬁed sine wave shown in Figs. 17-26 and 17-34, and sketch the line spectrum. In the interval 0 < !t < , f ðtÞ ¼ V sin !t; and from to 2, f ðtÞ ¼ 0. Then ð 1 An ¼ V sin !t ejn!t dð!tÞ 2 0 V ejn!t Vðejn þ 1Þ ¼ ¼ ðjn sin !t cos !tÞ 2 2 ð1 n Þ 2ð1 n2 Þ 0 For even n, An ¼ V=ð1 n2 Þ; for odd n, An ¼ 0. However, for n ¼ 1, the expression for An becomes indeterminate. L’Hoˆpital’s rule may be applied; in other words, the numerator and denominator are separately diﬀerentiated with respect to n, after which n is allowed to approach 1, with the result that A1 ¼ jðV=4Þ. The average value is ð i V 1 V h cos !t ¼ A0 ¼ V sin !t dð!tÞ ¼ 0 2 0 2 Then the exponential Fourier series is f ðtÞ ¼

V j4!t V j2!t V j!t V V j!t V j2!t V j4!t þj þ j e e e e e e 15 3 4 4 3 15

The harmonic amplitudes, V c0 ¼ A0 ¼

8 < 2V=ðn2 1Þ cn ¼ 2jAn j ¼ V=2 : 0

ðn ¼ 2; 4; 6; . . .Þ ðn ¼ 1Þ ðn ¼ 3; 5; 7; . . .Þ

are exactly as plotted in Fig. 17-27.

17.11 Find the average power in a resistance R ¼ 10 , if the current in Fourier series form is i ¼ 10 sin !t þ 5 sin 3!t þ 2 sin 5!t (A). The current has an eﬀective value Ieff ¼ 2 power is P ¼ Ieff R ¼ ð64:5Þ10 ¼ 645 W.

qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ pﬃﬃﬃﬃﬃﬃﬃﬃﬃ 2 2 2 1 1 1 64:5 ¼ 8:03 A. Then the average 2 ð10Þ þ 2 ð5Þ þ 2 ð2Þ ¼

Another Method The total power is the sum of the harmonic powers, which are given by 12 Vmax Imax cos . voltage across the resistor and the current are in phase for all harmonics, and n ¼ 0. Then,

But the

vR ¼ Ri ¼ 100 sin !t þ 50 sin 3!t þ 20 sin 5!t and P ¼ 12 ð100Þð10Þ þ 12 ð50Þð5Þ þ 12 ð20Þð2Þ ¼ 645 W.

17.12 Find the average power supplied to a network if the applied voltage and resulting current are v ¼ 50 þ 50 sin 5 103 t þ 30 sin 104 t þ 20 sin 2 104 t 3

4

ðVÞ

i ¼ 11:2 sin ð5 10 t þ 63:48Þ þ 10:6 sin ð10 t þ 458Þ þ 8:97 sin ð2 104 t þ 26:68Þ ðAÞ

442

FOURIER METHOD OF WAVEFORM ANALYSIS

[CHAP. 17

The total average power is the sum of the harmonic powers: P ¼ ð50Þð0Þ þ 12 ð50Þð11:2Þ cos 63:48 þ 12 ð30Þð10:6Þ cos 458 þ 12 ð20Þð8:97Þ cos 26:68 ¼ 317:7 W

17.13 Obtain the constants of the two-element series circuit with the applied voltage and resultant current given in Problem 17.12. The voltage series contains a constant term 50, but there is no corresponding term in the current series, thus indicating that one of the elements is a capacitor. Since power is delivered to the circuit, the other element must be a resistor. qﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ Ieff ¼ 12 ð11:2Þ2 þ 12 ð10:6Þ2 þ 12 ð8:97Þ2 ¼ 12:6 A 2 2 R, from which R ¼ P=Ieff ¼ 317:7=159:2 ¼ 2 . The average power is P ¼ Ieff 4 At ! ¼ 10 rad/s, the current leads the voltage by 458. Hence,

1 ¼ tan 458 ¼

1 !CR

or

C¼

1 ¼ 50 mF ð104 Þð2Þ

Therefore, the two-element series circuit consists of a resistor of 2 and a capacitor of 50 mF.

17.14 The voltage wave shown in Fig. 17-35 is applied to a series circuit of R ¼ 2 k and L ¼ 10 H. Use the trigonometric Fourier series to obtain the voltage across the resistor. Plot the line spectra of the applied voltage and vR to show the eﬀect of the inductance on the harmonics. ! ¼ 377 rad/s.

Fig. 17-35

The applied voltage has average value Vmax =, as in Problem 17.5. The wave function is even and hence the series contains only cosine terms, with coeﬃcients obtained by the following evaluation integral: an ¼

1

ð =2 300 cos !t cos n!t dð!tÞ ¼ =2

600 cos n=2 ð1 n2 Þ

V

Here, cos n=2 has the value 1 for n ¼ 2; 6; 10; . . . ; and þ1 for n ¼ 4; 8; 12; . . . . For n odd, cos n=2 ¼ 0. However, for n ¼ 1, the expression is indeterminate and must be evaluated separately. 300 !t sin 2!t =2 300 ¼ þ V 2 4 2 =2 =2 300 2 2 2 1 þ cos !t þ cos 2!t cos 4!t þ cos 6!t ðVÞ v¼ 2 3 15 35 a1 ¼

Thus,

1

ð =2

300 cos2 !t dð!tÞ ¼

In Table 17-3, the total impedance of the series circuit is computed for each harmonic in the voltage expression. The Fourier coeﬃcients of the current series are the voltage series coeﬃcients divided by the Zn ; the current terms lag the voltage terms by the phase angles n .

CHAP. 17]

443

FOURIER METHOD OF WAVEFORM ANALYSIS

Table 17-3 n

n!, rad/s

R, k

n!L; k

Zn ; k

0 1 2 4 6

0 377 754 1508 2262

2 2 2 2 2

0 3.77 7.54 15.08 22.62

2 4.26 7.78 15.2 22.6

I0 ¼

300= mA 2

i1 ¼

300=2 cos ð!t 628Þ 4:26

n 08 628 75.18 82.458 84.928

ðmAÞ

600=3 cos ð2!t 75:18Þ ðmAÞ 7:78 ....................................

i2 ¼ Then the current series is i¼

300 300 600 þ cos ð!t 628Þ þ cos ð2!t 75:18Þ 2 ð2Þð4:26Þ 3ð7:78Þ 600 600 cos ð4!t 82:458Þ þ cos ð6!t 84:928Þ 15ð15:2Þ 35ð22:6Þ

ðmAÞ

and the voltage across the resistor is vR ¼ Ri ¼ 95:5 þ 70:4 cos ð!t 628Þ þ 16:4 cos ð2!t 75:18Þ 1:67 cos ð4!t 82:458Þ þ 0:483 cos ð6!t 84:928Þ

ðVÞ

Figure 17-36 shows clearly how the harmonic amplitudes of the applied voltage have been reduced by the 10-H series inductance.

Fig. 17-36

17.15 The current in a 10-mH inductance has the waveform shown in Fig. 17-37. Obtain the trigonometric series for the voltage across the inductance, given that ! ¼ 500 rad/s.

Fig. 17-37

444

FOURIER METHOD OF WAVEFORM ANALYSIS

The derivative of the waveform of Fig. 17-37 is graphed in Fig. 17-38. V ¼ 20=. Hence, from Problem 17.1,

di 80 ¼ 2 ðsin !t þ 13 sin 3!t þ 15 sin 5!t þ Þ dð!tÞ and so

[CHAP. 17

This is just Fig. 17-18 with

ðAÞ

di 400 ¼ 2 ðsin !t þ 13 sin 3!t þ 15 sin 5!t þ Þ dð!tÞ

vL ¼ L!

ðVÞ

Fig. 17-38

Supplementary Problems 17.16

Synthesize the waveform for which the trigonometric Fourier series is f ðtÞ ¼

17.17

8V 1 1 fsin !t 19 sin 3!t þ 25 sin 5!t 49 sin 7!t þ g 2

Synthesize the waveform if its Fourier series is 40 1 ðcos !t þ 19 cos 3!t þ 25 cos 5!t þ Þ 2 20 ðsin !t 12 sin 2!t þ 13 sin 3!t 14 sin 4!t þ Þ þ

f ðtÞ ¼ 5

17.18

Synthesize the waveform for the given Fourier series.

1 1 1 1 1 1 cos !t cos 2!t þ cos 3!t cos 4!t cos 6!t þ 2 3 2 15 6 1 2 4 þ sin !t sin 2!t þ sin 4!t 4 3 15

f ðtÞ ¼ V

17.19

Find the trigonometric Fourier series for the sawtooth wave shown in Fig. 17-39 and plot the line spectrum. Compare with Example 17.1. Ans:

f ðtÞ ¼

V V þ ðsin !t þ 12 sin 2!t þ 13 sin 3!t þ Þ 2

CHAP. 17]

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-39 17.20

Fig. 17-40

Find the trigonometric Fourier series for the sawtooth wave shown in Fig. 17-40 and plot the spectrum. Compare with the result of Problem 17.3. Ans:

17.21

f ðtÞ ¼

2V fsin !t þ 12 sin 2!t þ 13 sin 3!t þ 14 sin 4!t þ g

Find the trigonometric Fourier series for the waveform shown in Fig. 17-41 and plot the line spectrum. Ans:

f ðtÞ ¼

4V 2V 1 fsin !t þ 13 sin 3!t þ 15 sin 5!t þ g fcos !t þ 19 cos 3!t þ 25 cos 5!t þ g 2

Fig. 17-41 17.22

Fig. 17-42

Find the trigonometric Fourier series of the square wave shown in Fig. 17-42 and plot the line spectrum. Compare with the result of Problem 17.1. Ans:

17.23

445

f ðtÞ ¼

4V fcos !t 13 cos 3!t þ 15 cos 5!t 17 cos 7!t þ g

Find the trigonometric Fourier series for the waveforms shown in Fig. 17-43. Plot the line spectrum of each and compare. 1 5 X 10 n 10 n Ans: ðaÞ f ðtÞ ¼ cos n!t þ sin n!t þ sin 1 cos 12 n¼1 n 12 n 12 1 50 X 10 n5 10 n5 ðbÞ f ðtÞ ¼ þ sin cos n!t þ 1 cos sin n!t 6 n 3 n 3 n¼1

Fig. 17-43 17.24

Find the trigonometric Fourier series for the half-wave-rectiﬁed sine wave shown in Fig. 17-44 and plot the line spectrum. Compare the answer with the results of Problems 17.5 and 17.6. V 2 2 2 1 þ cos !t þ cos 2!t cos 4!t þ cos 6!t Ans: f ðtÞ ¼ 2 3 15 35

446

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-44 17.25

f ðtÞ ¼

2V 2 2 ð1 þ 23 cos 2!t 15 cos 4!t þ 35 cos 6!t Þ

The waveform in Fig. 17-46 is that of Fig. 17-45 with the origin shifted. Find the Fourier series and show that the two spectra are identical. Ans:

f ðtÞ ¼

2V 2 2 ð1 23 cos 2!t 15 cos 4!t 35 cos 6!t Þ

Fig. 17-46 17.27

Fig. 17-47

Find the trigonometric Fourier series for the waveform shown in Fig. 17-47.

Ans:

17.28

Fig. 17-45

Find the trigonometric Fourier series for the full-wave-rectiﬁed sine wave shown in Fig. 17-45 and plot the spectrum. Ans:

17.26

[CHAP. 17

f ðtÞ ¼

1 X V V V cos !t þ ðcos n þ n sin n=2Þ cos n!t 2 2 ð1 n2 Þ n¼2 1 X V nV cos n=2 sin n!t þ sin !t þ 4 ð1 n2 Þ n¼2

Find the trigonometric Fourier series for the waveform shown in Fig. 17-48. Add this series termwise to that of Problem 17.27, and compare the sum with the series obtained in Problem 17.5.

Ans:

f ðtÞ ¼

1 1 X X V V Vðn sin n=2 1Þ V nV cos n=2 þ cos !t þ cos n!t þ sin !t þ sin n!t 2 2 2 4 1Þ ðn ð1 n2 Þ n¼2 n¼2

Fig. 17-48

Fig. 17-49

CHAP. 17]

17.29

1 1 j3!t 1 j2!t 1 1 j!t 1 f ðtÞ ¼ V þ e e e j j j þ 6 4 2 4 92 2 1 1 1 1 1 2þj þj e j!t þ j e j2!t e j3!t 2 4 6 92

Find the exponential Fourier series for the waveform shown in Fig. 17-50 and plot the line spectrum. Ans:

1 1 j3!t 1 j2!t 1 1 j!t 1 e e e þj þj þ 2þj þ f ðtÞ ¼ V þ 6 4 2 4 92 1 1 1 j2!t 1 1 e e j!t j e j3!t þ þ j þ 2j 2 4 6 92

Fig. 17-50

17.31

1 j3!t 1 1 1 1 j3!t e e f ðtÞ ¼ V þ j þ j ej!t þ j e j!t j 3 2 3

Find the exponential Fourier series for the sawtooth waveform shown in Fig. 17-52 and plot the spectrum. Convert the coeﬃcients obtained here into the trigonometric series coeﬃcients, write the trigonometric series, and compare the results with the series obtained in Problem 17.19. Ans:

1 j2!t 1 j!t 1 1 j!t 1 j2!t e e e j e þj þ j f ðtÞ ¼ V þ j 4 2 2 2 4

Fig. 17-52

17.33

Fig. 17-51

Find the exponential Fourier series for the square wave shown in Fig. 17-51 and plot the line spectrum. Add the exponential series of Problems 17.29 and 17.30 and compare the sum to the series obtained here. Ans:

17.32

447

Find the exponential Fourier series for the waveform shown in Fig. 17-49 and plot the line spectrum. Convert the coeﬃcients obtained here into the trigonometric series coeﬃcients, write the trigonometric series, and compare it with the result of Problem 17.4. Ans:

17.30

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-53

Find the exponential Fourier series for the waveform shown in Fig. 17-53 and plot the spectrum. Convert the trigonometric series coeﬃcients found in Problem 17.20 into exponential series coeﬃcients and compare them with the coeﬃcients of the series obtained here. Ans:

1 j2!t 1 1 1 j2!t e e f ðtÞ ¼ V j j ej!t þ j e j!t þ j þ 2 2

448

17.34

FOURIER METHOD OF WAVEFORM ANALYSIS

Find the exponential Fourier series for the waveform shown in Fig. 17-54 and plot the spectrum. Convert the coeﬃcients to trigonometric series coeﬃcients, write the trigonometric series, and compare it with that obtained in Problem 17.21.

Ans:

2 f ðtÞ ¼ V þ j 92 2 þ þj 92

Fig. 17-54

17.35

f ðtÞ ¼

Find the exponential Fourier series for the waveform shown in Fig. 17-56 and plot the line spectrum. V 2 j2!t V V V sin ej!t þ þ sin e j!t þ sin e Ans: f ðtÞ ¼ þ 2 6 6 6 6 V 2 j2!t sin þ þ e 2 6

Fig. 17-57

Find the exponential Fourier series for the half-wave-rectiﬁed sine wave shown in Fig. 17-57. Convert these coeﬃcients into the trigonometric series coeﬃcients, write the trigonometric series, and compare it with the result of Problem 17.24. Ans:

17.38

Fig. 17-55

2V ð þ 15 ej5!t 13 ej3!t þ ej!t þ e j!t 13 ej3!t þ 15 e j5!t Þ

Fig. 17-56

17.37

1 j3!t 2 1 j!t 2 1 j!t þ 2j þ 2þj e e e 3 1 e j3!t þ 3

Find the exponential Fourier series for the square wave shown in Fig. 17-55 and plot the line spectrum. Convert the trigonometric series coeﬃcients of Problem 17.22 into exponential series coeﬃcients and compare with the coeﬃcients in the result obtained here. Ans:

17.36

[CHAP. 17

f ðtÞ ¼

V j4!t V j2!t V j!t V V j!t V j2!t V j4!t þ e þ e þ þ e þ e þ e e 15 3 4 4 3 15

Find the exponential Fourier series for the full-wave rectiﬁed sine wave shown in Fig. 17-58 and plot the line spectrum. Ans:

f ðtÞ ¼

2V j4!t 2V j2!t 2V 2V j2!t 2V j4!t þ þ þ e e þ e e 15 3 3 15

CHAP. 17]

449

FOURIER METHOD OF WAVEFORM ANALYSIS

Fig. 17-58

17.39

Find the eﬀective voltage, eﬀective current, and average power supplied to a passive network if the applied voltage is v ¼ 200 þ 100 cos ð500t þ 308Þ þ 75 cos ð1500t þ 608Þ (V) and the resulting current is i ¼ 3:53 cos ð500t þ 758Þ þ 3:55 cos ð1500t þ 78:458Þ (A). Ans: 218.5 V, 3.54 A, 250.8 W

17.40

A voltage v ¼ 50 þ 25 sin 500t þ 10 sin 1500t þ 5 sin 2500t (V) is applied to the terminals of a passive network and the resulting current is i ¼ 5 þ 2:23 sin ð500t 26:68Þ þ 0:556 sin ð1500t 56:38Þ þ 0:186 sin ð2500t 68:28Þ Find the eﬀective voltage, eﬀective current, and the average power.

Ans:

ðAÞ

53.6 V, 5.25 A, 276.5 W

17.41

A three-element series circuit, with R ¼ 5 , L ¼ 5 mH, and C ¼ 50 mF, has an applied voltage v ¼ 150 sin 1000t þ 100 sin 2000t þ 75 sin 3000t (V). Find the eﬀective current and the average power for the circuit. Sketch the line spectrum of the voltage and the current, and note the eﬀect of series resonance. Ans: 16.58 A, 1374 W

17.42

A two-element series circuit, with R ¼ 10 and L ¼ 20 mH, has current i ¼ 5 sin 100t þ 3 sin 300t þ 2 sin 500t Find the eﬀective applied voltage and the average power.

17.43

vL ¼

200 ð j 13 ej3!t jej!t þ je j!t þ j 13 e j!t þ Þ 2

Fig. 17-59

ðVÞ

Fig. 17-60

A pure inductance, L ¼ 10 mH, has an applied voltage with the waveform shown in Fig. 17-60, where ! ¼ 200 rad/s. Obtain the current series in trigonometric form and identify the current waveform. Ans:

17.45

48 V, 190 W

A pure inductance, L ¼ 10 mH, has the triangular current wave shown in Fig. 17-59, where ! ¼ 500 rad/s. Obtain the exponential Fourier series for the voltage across the inductance. Compare the answer with the result of Problem 17.8. Ans:

17.44

Ans:

ðAÞ

i¼

20 1 1 ðsin !t 19 sin 3!t þ 25 sin 5!t 49 sin 7!t þ Þ ðAÞ; triangular

Figure 17-61 shows a full-wave-rectiﬁed sine wave representing the voltage applied to the terminals of an LC series circuit. Use the trigonometric Fourier series to ﬁnd the voltages across the inductor and the capacitor.

450

FOURIER METHOD OF WAVEFORM ANALYSIS 2 Ans:

vL ¼

vC ¼

3

7 4Vm 6 4!L 6 2!L cos 2!t cos 4!t þ 7 5 1 1 4 3 2!L 15 4!L 2!C 4!C 2 4Vm 6 61 42

[CHAP. 17

3

7 1 1 cos 2!t þ cos 4!t 7 5 1 1 3ð2!CÞ 2!L 15ð4!CÞ 4!L 2!C 4!C

Fig. 17-61

17.46

A three-element circuit consists of R ¼ 5 in series with a parallel combination of L and C. At Find the total current if the applied voltage is given by ! ¼ 500 rad/s, XL ¼ 2 , XC ¼ 8 . v ¼ 50 þ 20 sin 500t þ 10 sin 1000t (V). Ans: i ¼ 10 þ 3:53 sin ð500t 28:18Þ (A)

APPENDIX A

Complex Number System A1

COMPLEX NUMBERS

A2

COMPLEX PLANE

pﬃﬃﬃﬃﬃﬃﬃ A complex number z is a number of the form x þ jy, where x and y are real numbers and j ¼ 1. We write x ¼ Re z, the real part of z; y ¼ Im z, the imaginary part of z. Two complex numbers are equal if and only if their real parts are equal and their imaginary parts are equal.

A pair of orthogonal axes, with the horizontal axis displaying Re z and the vertical axis j Im z, determine a complex plane in which each complex number is a unique point. Refer to Fig. A-1, on which six complex numbers are shown. Equivalently, each complex number is represented by a unique vector from the origin of the complex plane, as illustrated for the complex number z6 in Fig. A-1.

Fig. A-1

Fig. A-2

451 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

452

A3

COMPLEX NUMBER SYSTEM

[APP. A

VECTOR OPERATOR j

In addition to the deﬁnition of j given in Section A1, it may be viewed as an operator which rotates any complex number (vector) A 908 in the counterclockwise direction. The case where A is a pure real number, x, is illustrated in Fig. A-2. The rotation sends A into jx, on the positive imaginary axis. Continuing, j 2 advances A 1808; j 3 , 2708; and j 4 , 3608. Also shown in Fig. A-2 is a complex number B in the ﬁrst quadrant, at angle . Note that jB is in the second quadrant, at angle þ 908.

A4

OTHER REPRESENTATIONS OF COMPLEX NUMBERS

In Section A1 complex numbers were deﬁned in rectangular form. In Fig. A-3, x ¼ r cos , y ¼ r sin , and the complex number z can be written in trigonometric form as z ¼ x þ jy ¼ rðcos þ j sin Þ where r is the modulus or absolute value (the notation r ¼ jzj is common), given by r ¼ angle ¼ tan1 ð y=xÞ is the argument of z.

pﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃﬃ x2 þ y2 , and the

Fig. A-3

Euler’s formula, e j ¼ cos þ j sin , permits another representation of a complex number, called the exponential form: z ¼ r cos þ jr sin ¼ rej A third form, widely used in circuit analysis, is the polar or Steinmetz form, z ¼ r , where is usually in degrees.

A5

SUM AND DIFFERENCE OF COMPLEX NUMBERS

To add two complex numbers, add the real parts and the imaginary parts separately. To subtract two complex numbers, subtract the real parts and the imaginary parts separately. From the practical standpoint, addition and subtraction of complex numbers can be performed conveniently only when both numbers are in the rectangular form. EXAMPLE A1 Given z1 ¼ 5 j2 and z2 ¼ 3 j8, z1 þ z2 ¼ ð5 3Þ þ jð2 8Þ ¼ 2 j10 z2 z1 ¼ ð3 5Þ þ jð8 þ 2Þ ¼ 8 j6

A6

MULTIPLICATION OF COMPLEX NUMBERS

The product of two complex numbers when both are in exponential form follows directly from the laws of exponents. _

z1 z2 ¼ ðr1 e j1 Þðr2 ej2 Þ ¼ r1 r2 e jð1 þ2 Þ

APP. A]

453

COMPLEX NUMBER SYSTEM

The polar or Steinmetz product is evident from reference to the exponential form. z1 z2 ¼ ðr1 1 Þðr2 2 Þ ¼ r1 r2 1 þ 2 The rectangular product can be found by treating the two complex numbers as binomials. z1 z2 ¼ ðx1 þ jy1 Þðx2 þ jy2 Þ ¼ x1 x2 þ jx1 y2 þ jy1 x2 þ j 2 y1 y2 ¼ ðx1 x2 y1 y2 Þ þ jðx1 y2 þ y1 x2 Þ EXAMPLE A2 If z1 ¼ 5e j=3 and z2 ¼ 2ej=6 , then z1 z2 ¼ ð5e j=3 Þð2ej=6 Þ ¼ 10e j=6 . EXAMPLE A3 If z1 ¼ 2 308 and z2 ¼ 5 458, then z1 z2 ¼ ð2 308Þð5 458Þ ¼ 10 158. EXAMPLE A4 If z1 ¼ 2 þ j3 and z2 ¼ 1 j3, then z1 z2 ¼ ð2 þ j3Þð1 j3Þ ¼ 7 j9.

A7

DIVISION OF COMPLEX NUMBERS

For two complex numbers in exponential form, the quotient follows directly from the laws of exponents. z1 r1 e j1 r1 jð1 2 Þ ¼ ¼ e z r2 e j2 r2 Again, the polar or Steinmetz form of division is evident from reference to the exponential form. z1 r1 1 r1 ¼ ¼ z2 r2 2 r2

1 2

Division of two complex numbers in the rectangular form is performed by multiplying the numerator and denominator by the conjugate of the denominator (see Section A8). z1 x1 þ jy1 x2 jy2 ðx x þ y1 y2 Þ þ jð y1 x2 y2 x1 Þ x1 x2 þ y1 y2 y x y2 x1 ¼ ¼ þ j 1 22 ¼ 1 2 2 2 2 2 z2 x2 þ jy2 x2 jy2 x2 þ y2 x2 þ y22 x2 þ y2 EXAMPLE A5 Given z1 ¼ 4e j=3 and z2 ¼ 2e j=6 , z1 4e j=3 ¼ ¼ 2e j=6 z2 2e j=6 EXAMPLE A6 Given z1 ¼ 8 308 and z2 ¼ 2 608, z1 8 308 ¼ 4 308 ¼ z2 2 608 EXAMPLE A7 Given z1 ¼ 4 j5 and z2 ¼ 1 þ j2, z1 4 j5 1 j2 6 13 ¼ j ¼ 5 5 z2 1 þ j2 1 j2

A8

CONJUGATE OF A COMPLEX NUMBER The conjugate of the complex number z ¼ x þ jy is the complex number z ¼ x jy. Thus, Re z ¼

z þ z 2

Im z ¼

z z 2j

jzj ¼

pﬃﬃﬃﬃﬃﬃﬃ zz

454

COMPLEX NUMBER SYSTEM

In the complex plane, the points z and z are mirror images in the axis of reals. In exponential form: z ¼ re j , z ¼ rej . In polar form: z ¼ r , z ¼ r . In trigonometric form: z ¼ rðcos þ j sin Þ, z ¼ rðcos j sin Þ. Conjugation has the following useful properties: ðiÞ ðz Þ ¼ z ðiiÞ ðz1 z2 Þ ¼ z1 z2

ðiiiÞ ðz1 z2 Þ ¼ z1 z2 z1 z ðivÞ ¼ 1 z2 z2

[APP. A

APPENDIX B

Matrices and Determinants B1

SIMULTANEOUS EQUATIONS AND THE CHARACTERISTIC MATRIX

Many engineering systems are described by a set of linearly independent simultaneous equations of the form y1 ¼ a11 x1 þ a12 x2 þ a13 x3 þ þ a1n xn y2 ¼ a21 x1 þ a22 x2 þ a23 x3 þ þ a2n xn ::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::: ym ¼ am1 x1 þ am2 x2 þ am3 x3 þ þ amn xn where the xj are the independent variables, the yi the dependent variables, and the aij are the coeﬃcients of the independent variables. The aij may be constants or functions of some parameter. A more convenient form may be obtained for the above equations by expressing them in matrix form. 2 3 2 32 3 y1 x1 a11 a12 a13 . . . a1n 6 y2 7 6 a21 a22 a23 . . . a2n 76 x2 7 6 7¼6 76 7 4 . . . 5 4 . . . . . . . . . . . . . . . 54 . . . 5 ym am1 am2 am3 . . . amn xn or Y ¼ AX, by a suitable deﬁnition of the product AX (see Section B3). Matrix A ½aij is called the characteristic matrix of the system; its order or dimension is denoted as dðAÞ m n where m is the number of rows and n is the number of columns.

B2

TYPES OF MATRICES

Row matrix. A matrix which may contain any number of columns but only one row; dðAÞ ¼ 1 n. Also called a row vector. Column matrix. A matrix which may contain any number of rows but only one column; dðAÞ ¼ m 1. Also called a column vector. Diagonal matrix. A matrix whose nonzero elements are all on the principal diagonal. 455 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

456

MATRICES AND DETERMINANTS

[APP. B

Unit matrix. A diagonal matrix having every diagonal element unity. Null matrix. A matrix in which every element is zero. Square matrix. A matrix in which the number of rows is equal to the number of columns; dðAÞ ¼ n n. Symmetric matrix. Given 2 3 a11 a12 a13 . . . a1n 6 a21 a22 a23 . . . a2n 7 7 dðAÞ ¼ m n A6 4 ... ... ... ... ... 5 am1 am2 am3 . . . amn the transpose of A is 2

a11 6 a12 6 AT 6 6 a13 4 ... a1n

a21 a22 a23 ... a2n

a31 a32 a33 ... a3n

... ... ... ... ...

Thus, the rows of A are the columns of AT , and symmetric matrix must then be square. Hermitian matrix. Given 2 a11 a12 6 a21 a22 A6 4 ... ... am1 am2

3 am1 am2 7 7 am3 7 7 ... 5 amn vice versa.

dðAT Þ ¼ n m

Matrix A is symmetric if A ¼ AT ; a

3 a1n a2n 7 7 ... 5 amn

a13 a23 ... am3

... ... ... ...

a13 a23 ... am3

3 . . . a1n . . . a2n 7 7 ... ... 5 . . . amn

the conjugate of A is 2

a11 6 a21 A 6 4 ... am1

a12 a22 ... am2

Matrix A is hermitian if A ¼ ðA ÞT ; that is, a hermitian matrix is a square matrix with real elements on the main diagonal and complex conjugate elements occupying positions that are mirror images in the main diagonal. Note that ðA ÞT ¼ ðAT Þ . Nonsingular matrix. An n n square matrix A is nonsingular (or invertible) if there exists an n n square matrix B such that AB ¼ BA ¼ I where I is the n n unit matrix. The matrix B is called the inverse of the nonsingular matrix A, and we write B ¼ A1 . If A is nonsingular, the matrix equation Y ¼ AX of Section B1 has, for any Y, the unique solution X ¼ A1 Y

B3

MATRIX ARITHMETIC

Addition and Subtraction of Matrices Two matrices of the same order are conformable for addition or subtraction; two matrices of diﬀerent orders cannot be added or subtracted. The sum (diﬀerence) of two m n matrices, A ¼ ½aij and B ¼ ½bij , is the m n matrix C of which each element is the sum (diﬀerence) of the corresponding elements of A and B. Thus, A B ¼ ½aij bij .

APP. B]

457

MATRICES AND DETERMINANTS

EXAMPLE B1 If

1 4 0 5 2 6 A¼ B¼ 2 7 3 0 1 1 1þ5 4þ2 0þ6 6 6 6 AþB¼ ¼ 2þ0 7þ1 3þ1 2 8 4 4 2 6 AB¼ 2 6 2

then

The transpose of the sum (diﬀerence) of two matrices is the sum (diﬀerence) of the two transposes: ðA BÞT ¼ AT BT Multiplication of Matrices The product AB, in that order, of a 1 m matrix A and an m 1 matrix B is a 1 1 matrix C ½c11 , where 2 3 b11 6 7 6 b21 7 6 7 7 C ¼ ½ a11 a12 a13 . . . a1m 6 6 b31 7 6 7 4 ... 5 bm1 " # m X ¼ ½a11 b11 þ a12 b21 þ . . . þ a1m bm1 ¼ a1k bk1 k¼1

Note that each element of the row matrix is multiplied into the corresponding element of the column matrix and then the products are summed. Usually, we identify C with the scalar c11 , treating it as an ordinary number drawn from the number ﬁeld to which the elements of A and B belong. The product AB, in that order, of the m s matrix A ¼ ½aij and the s n matrix B ¼ ½bij is the m n matrix C ¼ ½cij , where cij ¼

s X

aik bkj

ði ¼ 1; 2; . . . ; m;

j ¼ 1; 2; . . . ; nÞ

k¼1

EXAMPLE B2 2

3 2 3 a11 b11 þ a12 b21 a11 b12 þ a12 b22 a12 b b 12 a22 5 11 ¼ 4 a21 b11 þ a22 b21 a21 b12 þ a22 b22 5 b21 b22 a32 a31 b11 þ a32 b21 a31 b12 þ a32 b22 3 2 32 3 2 3 5 8 I1 3I1 þ 5I2 8I3 42 1 6 54 I2 5 ¼ 4 2I1 þ 1I2 þ 6I3 5 4 6 7 I3 4I1 6I2 þ 7I3 2 6 5ð8Þ þ ð3Þð7Þ 5ð2Þ þ ð3Þð0Þ 5ð6Þ þ ð3Þð9Þ 19 ¼ ¼ 0 9 4ð8Þ þ 2ð7Þ 4ð2Þ þ 2ð0Þ 4ð6Þ þ 2ð9Þ 46 a11 4 a21 a31

5 3 4 2

8 7

10 8

3 42

Matrix A is conformable to matrix B for multiplication. In other words, the product AB is deﬁned, only when the number of columns of A is equal to the number of rows of B. Thus, if A is a 3 2 matrix and B is a 2 5 matrix, then the product AB is deﬁned, but the product BA is not deﬁned. If D and E are 3 3 matrices, both products DE and ED are deﬁned. However, it is not necessarily true that DE ¼ ED. The transpose of the product of two matrices is the product of the two transposes taken in reverse order:

458

MATRICES AND DETERMINANTS

[APP. B

ðABÞT ¼ BT AT If A and B are nonsingular matrices of the same dimension, then AB is also nonsingular, with ðABÞ1 ¼ B1 A1 Multiplication of a Matrix by a Scalar The product of a matrix A ½aij by a scalar k is deﬁned by kA ¼ Ak ½kaij that is, each element of A is multiplied by k. kðA þ BÞ ¼ kA þ kB

B4 A.

Note the properties

kðABÞ ¼ ðkAÞB ¼ AðkBÞ

ðkAÞT ¼ kAT

DETERMINANT OF A SQUARE MATRIX Attached to any n n matrix A ½aij is a certain scalar function of the aij , called the determinant of This number is denoted as a11 a12 . . . a1n a21 a22 . . . a2n det A or jAj or A or ... ... ... ... a a ... a n1

n2

nn

where the last form puts into evidence the elements of A, upon which the number depends. determinants of order n ¼ 1 and n ¼ 2, we have explicitly a11 a12 ja11 j ¼ a11 a21 a22 ¼ a11 a22 a12 a21

For

For larger n, the analogous expressions become very cumbersome, and they are usually avoided by use of Laplace’s expansion theorem (see below). What is important is that the determinant is deﬁned in such a way that det AB ¼ ðdet AÞðdet BÞ for any two n n matrices A and B.

Two other basic properties are: T

det A ¼ det A

det kA ¼ kn det A

Finally, det A 6¼ 0 if and only if A is nonsingular. EXAMPLE B3 Verify the deteminant multiplication rule for 1 4 2 9 A¼ B¼ 3 2 1 We have

and But

1 4 2 9 2 9 þ 4 AB ¼ ¼ 3 2 1 4 27 þ 2 2 9 þ 4 4 27 þ 2 ¼ 2ð27 þ 2Þ ð9 þ 4Þð4Þ ¼ 90 þ 20 1 4 3 2 ¼ 1ð2Þ 4ð3Þ ¼ 10 2 9 1 ¼ 2ðÞ 9ð1Þ ¼ 9 2

APP. B]

459

MATRICES AND DETERMINANTS

and indeed 90 þ 20 ¼ ð10Þð9 2Þ.

Laplace’s Expansion Theorem The minor, Mij , of the element aij of a determinant of order n is the determinant of order n 1 obtained by deleting the row and column containing aij . The cofactor, ij , of the element aij is deﬁned as ij ¼ ð1Þiþj Mij Laplace’s theorem states: In the determinant of a square matrix A, multiply each element in the pth row (column) by the cofactor of the corresponding element in the qth row (column), and sum the products. Then the result is 0, for p 6¼ q; and det A, for p ¼ q. It follows at once from Laplace’s theorem that if A has two rows or two columns the same, then det A ¼ 0 (and A must be a singular matrix).

Matrix Inversion by Determinants; Cramer’s rule Laplace’s expansion theorem can be exhibited as a matrix multiplication, as follows: 2

3

a12

a13

...

a1n

11

21

31

...

n1

6a 6 21 6 4 ... an1 2

a22

a23

...

6 a2n 7 76 12 76 . . . 54 . . .

22

32

...

n2 7 7 7 ... 5

... an2

11 6 6 12 ¼6 4 ... 2

... ... ... ... ... 1n 2n 3n . . . nn an3 . . . ann 32 3 21 31 . . . n1 a11 a12 a13 . . . a1n 6 7 22 32 . . . n2 7 76 a21 a22 a23 . . . a2n 7 76 7 . . . . . . . . . . . . 54 . . . . . . . . . . . . . . . 5

1n 2n 3n . . . nn det A 0 0 ... 0

6 0 6 ¼6 4 ... 0 or

32

a11

det A ... 0

0 ... ... ... 0

...

0 ...

an1 3

an2

an3

. . . ann

7 7 7 5

det A

Aðadj AÞ ¼ ðadj AÞA ¼ ðdet AÞI

where adj A ½ji is the transposed matrix of the cofactors of the aij in the determinant of A, and I is the n n unit matrix. If A is nonsingular, one may divide through by det A 6¼ 0, and infer that A1 ¼

1 adj A det A

This means that the unique solution of the linear system Y ¼ AX is 1 adj A Y X¼ det A which is Cramer’s rule in matrix form. The ordinary, determinant form is obtained by considering the rth row ðr ¼ 1; 2; . . . ; nÞ of the matrix solution. Since the rth row of adj A is 1r 2r 3r . . . nr we have:

460

MATRICES AND DETERMINANTS

2 xr ¼

1 ½ 1r det A

2r

3r

y1

[APP. B

3

6 7 6 y2 7 6 7 7 . . . nr 6 6 y3 7 6 7 45 yn

1 ð y1 1r þ y2 2r þ y3 3r þ þ yn nr Þ det A a11 a1ðr1Þ y1 a1ðrþ1Þ a1n 1 a21 a2ðr1Þ y2 a2ðrþ1Þ a2n ¼ det A a a y a a ¼

n1

nr1Þ

n

nðrþ1Þ

nn

The last equality may be veriﬁed by applying Laplace’s theorem to the rth column of the given determinant.

B5

EIGENVALUES OF A SQUARE MATRIX

For a linear system Y ¼ AX, with n n characteristic matrix A, it is of particular importance to investigate the ‘‘excitations’’ X that produce a proportionate ‘‘response’’ Y. Thus, letting Y ¼ X, where is a scalar, X ¼ AX

or

ðI AÞX ¼ O

where O is the n 1 null matrix. Now, if the matrix I A were nonsingular, only the trival solution X ¼ Y ¼ O would exist. Hence, for a nontrivial solution, the value of must be such as to make I A a singular matrix; that is, we must have a11 a21 det ðI AÞ ¼ ... a n1

a12 a22 ... an2

a13 a23 ... an3

. . . a1n a2n ¼0 ... . . . ann

The n roots of this polynomial equation in are the eigenvalues of matrix A; the corresponding nontrivial solutions X are known as the eigenvectors of A. Setting ¼ 0 in the left side of the above characteristic equation, we see that the constant term in the equation must be det ðAÞ ¼ det ½ð1ÞA ¼ ð1Þn ðdet AÞ Since the coeﬃcient of n in the equation is obviously unity, the constant term is also equal to ð1Þn times the product of all the roots. The determinant of a square matrix is the product of all its eigenvalues—an alternate, and very useful, deﬁnition of the determinant.

INDEX

Ampliﬁers (Cont.): model of, 64–65 operational (see Op amps) Analog computes, 80–81 Analysis methods, 37–63 (See also Laws; Theorems) branch current, 37, 47, 56 determinant, 38–40 Laplace transform, 398–419 matrix/matrices, 38–40, 50–52 mesh (loop) current, 37–38, 42, 48, 56, 58, 62, 63, 198–200, 208 node voltage, 40–42, 57, 59, 61, 62, 201, 209 Apparent power, 226–230 in three-phase system, 259 Attenuator, 31 Autotransformers, 343–344, 354 Average power, 221–224, 236, 245–247, 427

ABC sequence, 250, 262–263, 266, 270 AC generator, 248, 260 AC power, 219–247 apparent, 226–230 average, 221–223, 224, 236, 245–247 complex, 226–230, 245, 247 energy exchanged between inductor/capacitor, 224–226 instantaneous, 219, 220, 224, 236 maximum power transfer, 233–234, 247 parallel-connected networks, 230–231 power factor improvement, 231–233 quadrature, 223 reactive, 223, 226–231, 243 real, 221–224 in RLC, 223–224 sinusoidal steady state, 220–221 AC wattmeter, 259, 265 Active circuits, 143–145, 175 ﬁrst-order, 143–145 higher-order, 175 Active elements, 7–8 Active ﬁlters, 282–283 Active phase shifter, 145 Admittance, 196, 205, 242, 305 combination of, 197 coupling, 201 diagram, 197 input, 201, 211 in parallel, 197 self-, 201 in series, 197 transfer, 201, 211 Admittance parameters, short-circuit (see Y-parameters) Air-core transformers, 340 Ampere, 1, 2 Ampere-hours, 5 Ampere-turn dot rule, 343 Ampere-turns, 343 Ampliﬁers, 64–100 diﬀerential/diﬀerence, 75 feedback in, 65–66 integrator/summer, 78–79 leaky integrator, 78

Bandpass ﬁlters, 283–284 Bandwidth, 299–300 Batteries, 5 Branch current method, 37, 47, 56 Capacitance/capacitors, 6, 7, 9, 12, 33, 156, 176 –177, 214 DC steady state in, 136 discharge in a resistor, 127–128 energy exchange between inductors, 224–226 establishing DC voltage across, 129–130 lossy, 301–302 in parallel, 26, 31 in series, 27, 31 Capacitive reactance, 196 Capacitive susceptance, 196 CBA sequence, 250, 263–264, 270 Center frequency, 283 Centi, 2 Circuit analysis, 362–397 applications, 428–430 circuit description, 362, 363 DC analysis, 364–367 using Spice and PSpice, 362–397 Circuits: analysis methods, 37–63 concepts, 7–23

461 Copyright 2003, 1997, 1986, 1965 by The McGraw-Hill Companies, Inc. Click Here for Terms of Use.

462

Circuits (Cont.): diagrams of, 12–13 diﬀerentiator, 79 elements in parallel, 26–27 elements in series, 25–26 ﬁrst-order, 127–160 active, 143–145 higher-order, 161–190 active, 175 integrator, 77–78 inverting, 71 laws regarding, 24–36 locus diagram, 290–292 noninverting, 72–73 noninverting integrators, 188 polyphase, 248–272 RC (see RC circuits) RL (see RL circuits) RLC (see RLC circuits) series-parallel conversions, 289 sign convention, 8 sinusoidal (see Sinusoidal circuits; Sinusoidal steady-state circuits) summing, 71–72 tank, 291 two-mesh, 167–168, 185 voltage-current relations, 9 Close coupling, 336 Coils, 250, 259, 298, 345 coupled, 336–338, 345–346 energy in a pair of, 338–340 in series, 206 Column matrix, 455 Comparators, 82–83 Complex frequency, 168–169, 178–179, 185 forced response and, 172–173 frequency scaling, 174 impedance of s-domain circuits, 169–170 magnitude scaling, 174 natural response and, 173–174 network function and, 170 –172 pole zero plots, 169–172 Complex frequency domain, 398 Complex inversion integral, 398 Complex number system, 451– 454 complex plane, 451 conjugate of, 453–454 diﬀerence of, 452 division of, 452–453 modulus or absolute value, 451 multiplication of, 452– 453 rectangular form, 451 representatives of, 451– 452 sum of, 452 trigonometric form, 451 vector operator, 451 Complex plane, 451

INDEX

Complex power, 226–230, 245–247 Computers: analog, 80–81 circuit analysis using, 362–397 PSpice program (see Spice and PSpice) Schematic Capture program, 362 Spice program (see Spice and PSpice) Conductance, 1, 215 Conduction, 2 Constant quantities, 4–6 Convergence region, 401 Cosine wave, 119, 421 Coulomb, 1, 2, 3 Coupled coils, 336–338 energy in a pair of, 338–340 Coupling admittance, 201 Coupling coeﬃcient, 335–336 Coupling ﬂux, 335 Cramer’s rule, 39, 459–460 Critically damped, 161, 163, 167, 284 Current, 1, 19, 20, 29 branch, 37, 47, 56, 205, 303 constant, 4 DC, 132 Kirchhoﬀ’s law, 24, 25, 37, 40 load, 252 loop, 37, 49, 57 magnetizing, 340–342 mesh, 37, 48, 56, 208, 216 natural, 336–338 Norton equivalent, 45–47 phase, 251–253 phasor, 429 relation to voltage, 9 variable, 4 Current dividers, 28–29, 198, 213 Damped sinusoids, 114 Damping, 161–163 critically damped, 161, 284 circuits in parallel, 167 RLC circuits in series, 162 overdamped, 161, 284 RLC circuits: in parallel, 165 in series, 162 underdamped, 161, 284 RLC circuits: in parallel, 166 in series, 162–163 Damping ratio, 284 DC analysis, 364–367 output statements, 367–370 DC current, establishing in an inductor, 132 DC steady state in inductors/capacitors, 136 Delta system, 251 balanced loads, 252–253

INDEX

Delta system (Cont.): equivalent wye connections and, 254–255 unbalanced loads, 255 Determinant method, 38–40 Diagonal matrix, 455 Diﬀerentiator circuit, 79 Diode, 13, 22, 23 forward-biased, 13 reverse-biased, 13 ideal, 22, 23 operating point, 23 terminal characteristic, 23 Direct Laplace transform, 398 Dirichlet condition, 420, 422, 430 Displacement neutral voltage, 257 Dissipation factor, 301 Dot rule, 338, 347–348, 375 ampere-turn, 343 Dynamic resistance, 13 Eigenvalues, 460 Electric charge, 1–3 Electric current, 2–3 Electric potential, 1, 3–4 Electric power, 4 Electrical units, 1–2, 223 Electrons, 2–3, 5 Elements: active, 7–8 nonlinear, 36 passive, 7–8 Energy (See also Power) exchange between inductors and capacitors, 224–226 kinetic, 3 potential, 3 work, 1, 3 Energy density, 432 Euler’s formula, 452 Euler’s identity, 196 Exponential function, 112–114, 132–134 Farad, 1 Faraday’s law, 335, 340 Farads, 9, 364 Feedback in ampliﬁer circuits, 65–66 Femto, 364 Filters, 280–282 active, 282–283 bandpass, 283–284 highpass, 144 low-pass, 81, 280 passive, 282–283 scaling frequency response of, 292 First-order circuits, 127–160 active, 143–145 Floating source, 75

463

Flux: coupling, 335 leakage, 336 linkage, 336 mutual, 340 Force, 1, 2 Forced response, 129 network function and, 172–173 Fourier integral, 430 Fourier method, 420–450 analysis using computers, 382 circuit analysis and, 428–430 eﬀective values and power, 427–428 exponential series, 422–423, 439–441, 447–448 trigonometric series, 422–423, 434–439, 444–445 waveform symmetry, 423–425 Fourier transform: inverse, 430, 432 properties of, 432–433 Frequency, 1, 103 center, 283 complex, 168–169 half-power, 278 natural, 187, 284 operating, 289 scaling, 292 Frequency domain, 196, 198 Frequency response, 81, 273–274 computer circuit analysis of, 373–374 half-power, 278 high-pass networks, 274–278 low-pass networks, 274–278 network functions and, 279–280 parallel LC circuits, 287–288 from pole-zero location, 280–281 scaling of, 292 series resonance and, 284–286 two-port/two-element networks, 278–279 Frequency scaling, 174 Gain, open loop, 65 Generators: Ac, 248, 260 three-phase, 249, 250 two-phase, 248 Giga, 2, 364 g-parameters, 317, 320 Half-power frequency, 278 Half-wave symmetry, 425, 435 Harmonics, 117, 425–426, 428–430, 441 Heaviside expansion formula, 403, 409 Henry, 1, 9, 364 Hermitian matrix, 456 Hertz, 1 Higher-order circuits, 161–190 active, 175

464

INDEX

High-pass ﬁlter, 144 Homogeneous solution, 127, 129 Horsepower, 6 h-parameters, 316, 320, 328 Hybrid parameters, 316, 320

Kilo, 2, 364 Kilowatt-hour, 5 Kinetic energy, 3 Kirchhoﬀ’s current law (KCL), 24, 25, 37, 40 Kirchhoﬀ’s voltage law (KVL), 24, 38, 401

Ideal transformers, 342–343 Impedance, 179, 204–205, 214, 269–270 combinations of, 197 diagram, 197 input, 200 in parallel, 197, 198 reﬂected, 344–345 in s-domain, 169–170 in series, 197, 198 sinusoidal steady-state circuits, 196–198 transfer, 200, 201 Impedance parameters, open-circuit (see Z-parameters) Impulse function: sifting property, 112 strength, 111 unit, 110–112 Impulse response: RC circuits and, 140–142 RL circuits and, 140–142 Inductance/inductors, 1, 7–9, 11, 15, 20 DC steady state in, 136 energy exchange between capacitors, 224–226 establishing DC current in, 132–133 leakage, 340 mutual, 334–335 in parallel, 30, 33 self-, 334–335 in series, 33 Induction motors, 244, 246 Inductive reactance, 329–330 Inductive susceptance, 196–197 Input admittance, 201, 211 Input impedance, 200 Input resistance, 41–42, 57 Instantaneous power, 219–220, 223, 224, 234–235, 248–250 Integrator circuit, 78–79 initial conditions of, 79 leaky, 78–79 noninverting, 188 International System of Units (SI), 1–2 Inverse Fourier transform, 430, 432 Inverse hybrid parameters, 317, 320 Inverse Laplace transform, 398 Inverting circuit, 71 Ions, 2 Iron-core transformer, 340

Lag network, 189 Laplace transform method, 398–419 circuits in s-domain, 404–405 convergence of the integral, 401 direct, 398 ﬁnal-value theorem, 401–402 Heaviside expansion formula, 403, 409 initial-value theorem, 401–402 inverse, 398 network function and, 405 partial-fraction expansion, 402–403 selected transforms, 400 Laplace’s expansion theorem, 459 Laws, 24–36 (See also Theorems) Kirchhoﬀ’s current, 24, 25, 37, 40 Kirchhoﬀ’s voltage, 24, 38, 401 Lenz’s, 338 Ohm’s, 9, 46 LC circuits, parallel, 288 Lead network, 189 Leakage ﬂux, 336 Leakage inductance, 340 Length, 1 Lenz’s law, 338 Lightning, 22 Line spectrum, 425–426 Linear transformers, 340–342, 353 Lining ﬂux, 336 Load current, 252 Locus diagram, 290–292 Loop current method (see Mesh current/mesh current method) Loop currents, 37, 49, 57 Lossy capacitors, 301–302 Low-pass ﬁlters, 80, 280

Joule, 1–4 Kelvin temperature, 1

Magnetic ﬂux, 1 Magnetic ﬂux density, 1 Magnetic ﬂux linkage, 336 Magnetizing current, 340–342 Magnitude scaling, 174, 183 Mass, 1 Matrix (matrices), 455–460 adding, 456–457 characteristics, 455 column, 455 diagonal, 455 eigenvalues of square, 460 Hermitian, 456 inversion by determinants, 459 multiplying, 457–458

INDEX

Matrix (Cont.): nonsingular, 456 null, 455 row, 455 scalar, 458 simultaneous equations, 455 square, 455, 458– 460 subtracting, 456 – 457 symmetric, 455 types of, 455–456 unit, 455 Z-matrix, 199–200 Matrix method, 38–40, 49–50 Maximum power transfer theorem, 47 Mega, 2, 364 Mesh current/mesh current method, 37, 38, 42–43, 48, 56, 58, 62, 63, 208, 216 sinusoidal circuits and, 198–200 Meter, 1 Methods, analysis (see Analysis methods) Micro, 2, 364 Milli, 2, 364 Minimum power, 35 Motors: induction, 244, 246 Mutual ﬂux, 340 Mutual inductance, 334–335 computer circuit analysis of, 375 conductively coupled equivalent circuit and, 329–330 coupled coils and, 336–338 coupling coeﬃcients and, 335–336 dot-rule and, 338 Nano, 2, 364 Natural current, 336–338 Natural frequency, 187, 284 Natural response, 129 network function and, 173–174 Network function, 170–172, 186, 405 forced response, 172–173 frequency response and, 279–280 Laplace transform and, 405 natural response, 173–174 pole zero plots, 171–172 Network reduction, 42, 44 Networks: conversion between Z- and Y-parameters, 315–316 g-parameters, 317, 320 high-pass, 274–278 h-parameters, 316, 320, 328 lag, 189 lead, 189 low-pass, 274–278 nonreciprocal, 311 parallel-connected, 230–231 parameter choices, 320 passive, 171

465

Networks (Cont.): pi-equivalent, 314 reciprocal, 311, 314 T-equivalent, 312 terminals characteristics, 310, 314–315 terminal parameters, 320–321 T-parameters, 317–318, 319, 320 two-mesh, 418 two-port, 310–333 two-port/two-element, 278–279 Y-parameters, 312–314, 319, 320, 324 Z-parameters, 310–312, 318, 320–323, 325 Newton, 1, 2 Newton-meter, 2 Node, 24 principal, 24 simple, 24 Node voltage method, 40–42, 51, 57, 59, 61, 62, 209, 210 sinusoidal circuits and, 201 Noninverting circuits, 72–73 Noninverting integrators, 188 Nonlinear element, 36 Nonlinear resistors, 13–14 dynamic resistance, 13 static resistance, 13 Nonperiodic functions, 108–109 Nonreciprocal networks, 311 Nonsingular matrix, 456 Norton equivalent current, 45–47, 218 Norton’s theorem, 45–47, 59–60, 212–213, 217, 218 sinusoidal circuits and, 201–202 Null matrix, 455 Number systems, complex (see Complex number system) Ohm, 1, 9, 364 Ohm’s law, 9, 46 Op amps, 66–69 circuit analysis of, 70–71 circuits containing several, 76–77 computer circuit analysis of, 370–372 voltage follower, 74, 97 Open-loop gain, 65 Operating point, diode, 23 Operational ampliﬁers (see Op amps) Overdamping, 161, 162, 165, 284 Partial-fraction expansion, 402–403 Particular solution, 127, 129 Passive elements, 7–8 Passive ﬁlters, 282–283 Passive phase shifter, 145 Periodic function, 101–102, 219 average/eﬀective RMS values, 107–108 combination of, 106 Periodic pulse, 102 Periodic tone burst, 102

466

Phase angle, 1, 178–179, 192–193, 195 Phase current, 251–253 Phase shift, 103–105 Phase shifter, 145 active, 145 passive, 145 Phasor voltage, 251 Phasors, 194–195 deﬁning, 194 diagrams, 195 equivalent notations of, 195 phase diﬀerence of, 193 voltage, 207 Pico, 2, 364 Pi-equivalent network, 314 Plane angle, 1 Polarity, 8, 29, 250 instantaneous, 338 Pole zero plots (see Zero pole plots) Polyphase circuits, 248, 272 ABC sequence, 250, 262–263, 266, 270 CBA sequence, 250, 263–264, 270 CBA or ABC, 272 delta system, 251 balanced loads, 252–253 equivalent wye connections and, 254–255 unbalanced loads, 255 instantaneous power, 248 phasor voltages, 251 power measurement with wattmeters, 259–260 three-phase loads, single-line equivalent for, 255 three-phase power, 258–259 three-phase systems, 249–251 two-phase systems, 248–249 wye system, 251 balanced loads, 253–254 equivalent delta connections and, 254–255 unbalanced four-wire loads, 256 unbalanced three-wire loads, 257–258 Potential energy, 3 Potentiometer, 31 Power, 1, 2, 18–19, 21, 84 (See also Energy) absorbed, 84 ac, 219–247 apparent, 226–230, 259 average, 221–224, 236, 245–247 complex, 226–230, 245, 247 eﬀective values and, 427–428 electrical, 4 instantaneous, 219, 220, 224, 236 minimum, 35 quadrature, 223 reactive, 223, 226–231, 243, 259–260 real, 221–224 in sinusoidal steady state, 220–221 superposition of, 234 in three-phase systems, 259–260

INDEX

Power factor, 231–232, 238–240 improving, 231–233 in three-phase systems, 259–260 Power transfer, maximum, 233–234 Power triangle, 226–230, 240–241 Primary winding, 340 Principal node, 24 PSpice (see Spice and PSpice) Pulse, response of ﬁrst-order circuits to, 139–140 Quadrature power, 223 Quality factor, 286–287, 297 Radian, 1 Random signals, 115–116 RC circuits: complex ﬁrst-order, 134–135 impulse response of, 140–142 in parallel, 122, 290 response: to exponential excitations, 141–142 to pulse, 139–140 to sinusoidal excitations, 143–145 in series, 155–157, 204, 214 step response of, 141–142 two-branch, 304 Reactance, 196 inductive, 329–330 Reactive power, 223, 226, 243 in three-phase systems, 259–260 Real power, 221–224 Reciprocal networks, 311 pi-equivalent of, 314 Reﬂected impedance, 344–345 Resistance/resistors, 1, 9, 10 capacitor discharge in, 127–128 distributed, 7–8 dynamic, 13 input, 41–42, 57 nonlinear, 13–14 in parallel, 26, 28, 30, 32 in series, 25, 28 static, 13 transfer, 42, 58 Resonance, 283–284, 293–295, 299, 305–306 parallel, 287 series, 284–286 RL circuits: complex ﬁrst-order, 134–135 impulse response of, 140–142 response: to exponential excitations, 141–142 to pulse, 139–140 to sinusoidal excitations, 143–145 in series, 152–153, 156, 291 source-free, 130–131

INDEX

RL circuits (Cont.): step response of, 141–142 two-branch, 304 RLC circuits: ac power in, 223–224 in parallel, 164–167, 177 critically damped, 167 overdamped, 165 underdamped, 166 natural resonant frequency, 185 quality factor, 297 resonance: parallel, 287 series, 284–286 scaled element values, 188 s-domain impedance, 170 in series, 161–164, 176–177, 290–292 critically damped, 163 overdamped, 162 underdamped, 164 transient current, 185 transient voltage, 185 Root-mean-square (RMS), 4 average/eﬀective values, 107–108 Row matrix, 455 Saturation, 82, 83 Sawtooth wave, 420, 426, 444 Scalar, 440 Scaling: frequency, 174, 292 magnitude, 174, 183 s-domain circuits, 185, 404 impedance, 169–170 impedance of RLC circuits, 170 passive networks in, 171 Second, 1 Secondary winding, 340 Self-admittance, 201 Self-inductance, 334–335 Sensitivity, 97 analysis using computers, 382 Siemens, 1 Signals: nonperiodic, 108–109 periodic, 101–102, 106, 219 random, 115–116 Simple node, 24 Sine wave, 101, 421 Sinusoidal circuits: Norton’s theorem and, 201–202 steady-state node voltage method and, 201 The´venin’s theorem and, 201–202 Sinusoidal functions, 103 Sinusoidal steady-state circuits, 191–218 admittance, 196–198 element responses, 191–193

467

Sinusoidal steady-state circuits (Cont.): impedance, 196–198 mesh current method and, 198–200 phase angle, 192–193 phasors, 193–196 voltage/current division in frequency domain, 198 SI units, 1–2 Software (see Computers; Spice and PSpice) Spice and PSpice, 362–397 ac steady state, 373–374 AC statement, 373 independent sources, 373 .PLOT AC statement, 373 .PRINT AC statement, 373 data statements: controlled sources, 366–367 current-controlled sources, 366–367 dependent sources, 366 independent sources, 365 linearly dependent sources, 366 passive elements, 364 scale factors and symbols, 364 voltage-controlled sources, 366–367 DC analysis: output statements, 367–370 using, 364–367 exponential source, 379 Fourier analysis, 382 frequency response, 373–374 modeling devices, 375–377 mutual inductance, 375 op amp circuit analysis, 370–372 pulse source, 380 sensitivity analysis, 382 sinusoidal source, 380 source ﬁle: control statements, 363 data statements, 363 dissecting, 363 .END statement, 363 output statements, 363 title statement, 363 specifying other sources, 379–382 .SUBCKT statement, 371 The´venin equivalent, 370 time response, 378–379 transformers, 375 transient analysis, 378–379 s-plane plot, 186 Square matrix, 455, 458–460 Static resistance, 13 Steady state, 127 DC in inductors/capacitors, 136 Steradian, 1 Summing circuit, 71–72 Superposition, 44–45, 60–63, 99 of average powers, 234

468

Susceptance, 196 Switching, 87, 148 transition at, 136 –138 Symmetric matrix, 455 Symmetry: half-wave, 425, 435 waveforms, 423–425 Synthesis, waveform, 426 Tank circuit, 291 Temperature, kelvin, 1 T-equivalent network, 312 Tera, 2, 364 Terminal characteristics, 310, 314–315 Terminal parameters, 320–321 Tesla, 1 Theorems: ﬁnal-value, 401–402 initial-value, 401–402 Laplace’s expansion, 459 maximum power transfer, 47 Norton’s, 45–47, 60–61, 201–202, 212–213, 217 The´venin’s, 45–47, 53, 60–61, 201–202, 211–213, 217, 370 (See also Laws) The´venin equivalent voltage, 45, 218 The´venin’s theorem, 45–47, 53, 60–61, 211–213, 217, 218, 370 sinusoidal circuits and, 201–202 Three-phase systems (see Polyphase circuits) Time, 1 Time constant, 112, 132–133 Time domain, 196, 398 Time function, 178–179, 406–407 nonperiodic, 101, 108–109 periodic, 101–102, 106 random, 101 Time response: computer circuit analysis of, 378–379 Time shift, 103–105 Tone burst, 121 T-parameters, 317–320 Transducers, 246 Transfer admittance, 201, 211 Transfer function, 186, 298, 370 Transfer impedance, 200, 210 Transfer resistance, 42, 58 Transformer rating, 243 Transformers, 246 air-core, 340 auto-, 343–344, 354 computer circuit analysis of, 375 ideal, 342–343 iron-core, 340 linear, 340–342, 353 reﬂected impedance of, 344–345

INDEX

Transients, 127 computer circuit analysis of, 378–379 Two-mesh circuits, 167–168, 185 Two-mesh networks, 418 Two-port networks, 278–279, 310–333 cascade connection, 319 converting between Z- and Y-parameters, 315–316 g-parameters, 317, 320 h-parameters, 316, 320, 328 interconnecting, 318–319 parallel connection, 319 series connection, 318 T-equivalent of, 312 terminals and, 310 T-parameters, 317–320 Y-parameters, 312–314, 319, 320, 324 Z-parameters, 310–312, 318, 320–323, 325 Underdamping, 161, 164, 166, 284 Unit delta function, 110–112 Unit impulse function, 110–112 Unit impulse response, 140–142 Unit matrix, 455 Unit step function, 109–110 Unit step response, 140–142 Vector operator, 452 Volt, 1, 3 Voltage, 18 displacement neutral, 257 Kirchhoﬀ’s law, 24, 38, 401 node, 40–42, 51, 57, 59, 201–202, 209, 210 phasor, 251 polarity, 250 relation to current, 9 The´venin equivalent, 45 Volt-ampere reactive, 223 Voltage dividers, 28, 33, 181, 198, 207, 213, 294 Voltage drop, 24 Voltage followers, 74, 97 Voltage ratio, 293 Voltage sources: dependent, 7 independent, 7 Voltage transfer function, 181–182, 304 Watt, 1, 2, 4 Wattmeters, 265 power measurement with, 259–260 Waveforms: analysis using Fourier method, 420–450 continuous spectrum of, 432–434 cosine, 421 eﬀective values and power, 427–428 energy density of, 432 line spectrum, 425–426

INDEX

Waveforms (Cont.): nonperiodic transforming, 430–431 periodic, 420 sawtooth, 420, 426, 444 sine, 101, 421 symmetry of, 423–425, 435 synthesis of, 426, 444 Weber, 1 Winding, 346–348 primary, 340 secondary, 340 Work energy, 1, 2 Wye system, 251 balanced four-wire loads, 253–254

Wye system (Cont.): equivalent delta connections and, 254–255 unbalanced four-wire loads, 256 unbalanced three-wire loads, 257–258 Y-parameters, 312–314, 319, 320, 324 converting between Z-parameters and, 315–316 Zero pole plots, 170–173, 181–182, 186–187 frequency response from, 280–281 Z-matrix, 192–193 Z-parameters, 310–312, 318, 320–323, 325 converting between Y-parameters and, 315–316

469