MASS TRANSFER IN MULTIPHASE SYSTEMS AND ITS APPLICATIONS Edited by Mohamed El-Amin
Mass Transfer in Multiphase Systems and its Applications Edited by Mohamed El-Amin
Published by InTech Janeza Trdine 9, 51000 Rijeka, Croatia Copyright © 2011 InTech All chapters are Open Access articles distributed under the Creative Commons Non Commercial Share Alike Attribution 3.0 license, which permits to copy, distribute, transmit, and adapt the work in any medium, so long as the original work is properly cited. After this work has been published by InTech, authors have the right to republish it, in whole or part, in any publication of which they are the author, and to make other personal use of the work. Any republication, referencing or personal use of the work must explicitly identify the original source. Statements and opinions expressed in the chapters are these of the individual contributors and not necessarily those of the editors or publisher. No responsibility is accepted for the accuracy of information contained in the published articles. The publisher assumes no responsibility for any damage or injury to persons or property arising out of the use of any materials, instructions, methods or ideas contained in the book. Publishing Process Manager Iva Lipovic Technical Editor Teodora Smiljanic Cover Designer Martina Sirotic Image Copyright timy, 2010. Used under license from Shutterstock.com First published February, 2011 Printed in India A free online edition of this book is available at www.intechopen.com Additional hard copies can be obtained from
[email protected]
Mass Transfer in Multiphase Systems and its Applications, Edited by Mohamed El-Amin p. cm. ISBN 978-953-307-215-9
free online editions of InTech Books and Journals can be found at www.intechopen.com
Contents Preface
IX
Chapter 1
Mass and Heat Transfer During Two-Phase Flow in Porous Media - Theory and Modeling 1 Jennifer Niessner and S. Majid Hassanizadeh
Chapter 2
Solute Transport With Chemical Reaction in Singleand Multi-Phase Flow in Porous Media M.F. El-Amin, Amgad Salama and Shuyu Sun
23
Chapter 3
Multiphase Modelling of Thermomechanical Behaviour of Early-Age Silicate Composites 49 Jiří Vala
Chapter 4
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection 67 Konstantin Kostarev, Andrew Shmyrov, Andrew Zuev and Antonio Viviani
Chapter 5
Mass Transfer in Multiphase Mechanically Agitated Systems 93 Anna Kiełbus-Rąpała and Joanna Karcz
Chapter 6
Gas-Liquid Mass Transfer in an Unbaffled Vessel Agitated by Unsteadily Forward-Reverse Rotating Multiple Impellers 117 Masanori Yoshida, Kazuaki Yamagiwa, Akira Ohkawa and Shuichi Tezura
Chapter 7
Toward a Multiphase Local Approach in the Modeling of Flotation and Mass Transfer in Gas-Liquid Contacting Systems 137 Jamel Chahed and Kamel M’Rabet
Chapter 8
Mass Transfer in Two-Phase Gas-Liquid Flow in a Tube and in Channels of Complex Configuration Nikolay Pecherkin and Vladimir Chekhovich
155
VI
Contents
Chapter 9
Laminar Mixed Convection Heat and Mass Transfer with Phase Change and Flow Reversal in Channels 179 Brahim Benhamou, Othmane Oulaid, Mohamed Aboudou Kassim and Nicolas Galanis
Chapter 10
Liquid-Liquid Extraction With and Without a Chemical Reaction 207 Claudia Irina Koncsag and Alina Barbulescu
Chapter 11
Modeling Enhanced Diffusion Mass Transfer in Metals during Mechanical Alloying 233 Boris B. Khina and Grigoriy F. Lovshenko
Chapter 12
Mass Transfer in Steelmaking Operations Roberto Parreiras Tavares
Chapter 13
Effects of Surface Tension on Mass Transfer Devices Honda (Hung-Ta) Wu and Tsair-Wang Chung
Chapter 14
Overall Mass-Transfer Coefficient for Wood Drying Curves Predictions 301 Rubén A. Ananias, Laurent Chrusciel, André Zoulalian, Carlos Salinas-Lira and Eric Mougel
Chapter 15
Transport Phenomena in Paper and Wood-based Panels Production Helena Aguilar Ribeiro, Luisa Carvalho, Jorge Martins and Carlos Costa
255
313
Chapter 16
Control of Polymorphism and Mass-transfer in Al2O3 Scale Formed by Oxidation of Alumina-Forming Alloys 343 Satoshi Kitaoka, Tsuneaki Matsudaira and Masashi Wada
Chapter 17
Mass Transfer Investigation of Organic Acid Extraction with Trioctylamine and Aliquat 336 Dissolved in Various Solvents 367 Monwar Hossain
Chapter 18
New Approaches for Theoretical Estimation of Mass Transfer Parameters in Both Gas-Liquid and Slurry Bubble Columns 389 Stoyan Nedeltchev and Adrian Schumpe
Chapter 19
Influence of Mass Transfer and Kinetics on Biodiesel Production Process 433 Ida Poljanšek and Blaž Likozar
273
Contents
Chapter 20
Condensation Capture of Fine Dust in Jet Scrubbers M.I. Shilyaev and E.M. Khromova
Chapter 21
Mass Transfer in Filtration Combustion Processes David Lempert, Sergei Glazov and Georgy Manelis
Chapter 22
Mass Transfer in Hollow Fiber Supported Liquid Membrane for As and Hg Removal from Produced Water in Upstream Petroleum Operation in the Gulf of Thailand 499 U. Pancharoen, A.W. Lothongkum and S. Chaturabul
Chapter 23
Mass Transfer in Fluidized Bed Drying of Moist Particulate 525 Yassir T. Makkawi and Raffaella Ocone
Chapter 24
Simulation Studies on the Coupling Process of Heat/Mass Transfer in a Metal Hydride Reactor Fusheng Yang and Zaoxiao Zhang
459
483
549
Chapter 25
Mass Transfer around Active Particles in Fluidized Beds 571 Fabrizio Scala
Chapter 26
Mass Transfer Phenomena and Biological Membranes 593 Parvin Zakeri-Milani and Hadi Valizadeh
Chapter 27
Heat and Mass Transfer in Packed Bed Drying of Shrinking Particles 621 Manoel Marcelo do Prado and Dermeval José Mazzini Sartori
Chapter 28
Impact of Mass Transfer on Modelling and Simulation of Reactive Distillation Columns 649 Zuzana Švandová, Jozef Markoš and Ľudovít Jelemenský
Chapter 29
Mass Transfer through Catalytic Membrane Layer 677 Nagy Endre
Chapter 30
Mass Transfer in Bioreactors 717 Ma. del Carmen Chávez, Linda V. González, Mayra Ruiz, Ma. de la Luz X. Negrete, Oscar Martín Hernández and Eleazar M. Escamilla
Chapter 31
Analytical Solutions of Mass Transfer around a Prolate or an Oblate Spheroid Immersed in a Packed Bed 765 J.M.P.Q. Delgado and M. Vázquez da Silva
VII
Preface This book covers a number of developing topics in mass transfer processes in multiphase systems for a variety of applications. The book effectively blends theoretical, numerical, modeling, and experimental aspects of mass transfer in multiphase systems that are usually encountered in many research areas such as chemical, reactor, environmental and petroleum engineering. From biological and chemical reactors to paper and wood industry and all the way to thin film, the 31 chapters of this book serve as an important reference for any researcher or engineer working in the field of mass transfer and related topics. The first chapter focuses on the description and modeling of mass transfer processes occurring between two fluid phases in a porous medium, while the second chapter is concerned with the basic principles underlying transport phenomena and chemical reaction in single- and multi-phase systems in porous media. Chapter 3 introduces the multiphase modeling of thermomechanical behavior of early-age silicate composites. The surfactant transfer in multiphase liquid systems under conditions of weak gravitational convection is presented in Chapter 4. In the fifth chapter the volumetric mass transfer coefficient for multiphase mechanically agitated gas–liquid and gas–solid–liquid systems is obtained experimentally. Further, gas-liquid mass transfer analysis in an unbaffled vessel agitated by unsteadily forward-reverse rotating multiple impellers is provided in Chapter 6. Chapter 7 discuses the kinetic model of flotation based on the theory of mass transfer in gas-liquid bubbly flows. The eighth chapter deals with experimental investigation of mass transfer and wall shear stress, and their interaction at the concurrent gas-liquid flow in a vertical tube, in a channel with flow turn, and in a channel with abrupt expansion. The laminar mixed convection with mass transfer and phase change of flow reversal in channels is studied in the ninth chapter, and the tenth chapter exemplifies the theoretical aspects of the liquid-liquid extraction with and without a chemical reaction and the dimensioning of the extractors with original experimental work and interpretations. The eleventh chapter introduces analysis of the existing theories and concepts of solidstate diffusion mass transfer in metals during mechanical alloying. In Chapter 12 the mass transfer coefficient is given for different situations (liquid-liquid, liquid-gas and liquid-solid) of two-phase mass transfer of steelmaking processes. Chapter 13 discusses the effect of Marangoni Instability on thin liquid film, thinker liquid layer and mass transfer devices.
X
Preface
Chapter 14 provides a review of model permitting the determination of wood drying rate represented by an overall mass transfer coefficient and a driving force. Moreoever, transport phenomena in paper and wood-based panels’ production are discussed in Chapter 15. In the sixteenth chapter the effect of lutetium doping on oxygen permeability in polycrystalline alumina wafers exposed to steep oxygen potential gradients was evaluated at high temperatures to investigate the mass-transfer phenomena. Mass transfer investigation of organic acid extraction with trioctylamine and aliquat336 dissolved in various solvents is introduced in Chapter 17. Chapter 18 is focused on the development of semi-theoretical methods for calculation of gas holdup, interfacial area and liquid-phase mass transfer coefficients in gas-liquid and slurry bubble column reactors. Chapter 19 investigates the influence of mass transfer and kinetics on biodiesel (fatt y acid alkyl) production process. The physical-mathematical model of heat and mass transfer and condensation capture of fine dust on fluid droplets dispersed in jet scrubbers is suggested and analyzed in Chapter 20, while Chapter 21 is devoted to investigate mass transfer in filtration combustion processes. The twenty-second chapter describes the merits of using hollow fiber supported liquid membranes (HFSLM), one of liquid membranes in supported (not clear) structures, and how mass transfer involves step-by-step in removing arsenic (As) and mercury (Hg). The twenty-third chapter presents an overview of the various mechanisms contributing to particulate drying in a bubbling fluidized bed and the mass transfer coefficient corresponding to each mechanism. A mathematical model and numerical simulation for hydriding/dehydriding process in a tubular type MH reactor packed with LaNi5 were provided in the twenty-fourth chapter. Chapter 25 is dedicated to the mass transfer coefficient around freely moving active particles in the dense phase of a fluidized bed. Chapter 26 is aimed at reviewing transport across biological membranes, with an emphasis on intestinal absorption, its model analysis and permeability prediction. The objective of the twenty-seventh chapter is to provide comprehensive information on theoretical-experimental analysis of coupled heat and mass transfer in packed bed drying of shrinking particles. The twenty-eighth chapter focuses on vapour-liquid mass transfer influence on the prediction of RD column behaviour neglecting the liquid-solid and intraparticle mass transfer. Mass transfer through catalytic membrane layer is studied in Chapter 29. In chapter 30 three types of bioreactors and stirred tank applied to biological systems are introduced and a mathematical model is developed. Finally in Chapter 31 analytical solutions of mass transfer around a prolate or an oblate spheroid immersed in a packed bed are obtained.
Mohamed Fathy El-Amin Physical Sciences and Engineering Division King Abdullah University of Science and Technology (KAUST)
0 1 Mass and Heat Transfer During Two-Phase Flow in Porous Media - Theory and Modeling Jennifer Niessner1 and S. Majid Hassanizadeh2 1 Institute
2 Department
of Hydraulic Engineering, University of Stuttgart, Stuttgart of Earth Sciences, Faculty of Geosciences, Utrecht University, Utrecht 1 Germany 2 The Netherlands
1. Introduction 1.1 Motivation
This chapter focusses on the description and modeling of mass transfer processes occurring between two fluid phases in a porous medium. The principle underlying physical process comprises a transport of particles from one phase to the other phase. This process takes place across fluid–fluid interfaces (see Fig. 1) and may constitute evaporation, dissolution, or condensation, for example. Such mass transfer processes are crucial in many applications involving flow and transport in porous media. Major examples are found in soil science (where the evaporation from soils is of interest), soil and groundwater remediation (like thermally-enhanced soil vapor extraction where dissolution, evaporation, and condensation play a role), storage of carbon dioxide in the subsurface (where the dissolution of carbon dioxide in the surrounding groundwater is a crucial storage mechanism), CO2 -enhanced oil recovery (where after primary and secondary recovery, carbon dioxide is injected into the reservoir in order to mobilize an additional 8-20 per cent of oil), and various industrial porous systems (such as certain types of fuel cells). Let us have a closer look at a few of these applications and identify where interphase mass transfer is relevant. Four specific examples are shown in Fig. 2 and briefly described.
solid phase fluid phase 1
fluid phase 2
Fig. 1. Mass transfer processes (evaporation, dissolution, condensation) imply a transfer of particles across fluid–fluid interfaces.
2 2
Transfer Mass Transfer in Multiphase Systems andMass its Applications
(a) Carbon dioxide storage in the subsurface (figure from IPCC (2005))
(b) Soil contamination and remediation
precipitation
radiation
infiltration evaporation
groundwater
(c) Enhanced www.oxy.com)
oil
recovery
(figure
from
(d) Evaporation from soil
Fig. 2. Four applications of flow and transport in porous media where interphase mass transfer is important
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
33
(a) Carbon capture and storage (Fig. 2 (a)) is a recent strategy to mitigate the greenhouse effect by capturing the greenhouse gas carbon dioxide that is emitted e.g. by coal power plants and inject it directly into the subsurface below an impermeable caprock. Here, three different storage mechanisms are relevant on different time scales: 1) The capillary barrier mechanism of the caprock. This geologic layer is meant to keep the carbon dioxide in the storage reservoir as a separate phase. 2) Dissolution of the carbon dioxide in the surrounding brine (salty groundwater). This is a longterm storage mechanism and involves a mass transfer process as carbon dioxide molecules are “transferred” from the gaseous phase to the brine phase. 3) Geochemical reactions which immobilize the carbon dioxide through incorporation into the rock matrix. (b) Shown in Fig. 2 (b) is a cartoon of a light non-aqueous phase liquid (LNAPL) soil contamination and its clean up by injection of steam at wells located around the contaminated soil. The idea behind this strategy is to mobilize the initially immobile (residual) LNAPL by evaporation of LNAPL component at large rates into the gaseous phase. The soil gas is then extracted by a centrally located extraction well. It means that the remediation mechanism relies on the evaporation of LNAPL component which represents a mass transfer from the liquid LNAPL phase into the gaseous phase. (c) In order to produce an additional 8-20% of oil after primary and secondary recovery, carbon dioxide may be injected into an oil reservoir, e.g. alternatingly with water, see Fig. 2 (c). This is called enhanced oil recovery. The advantage of injecting carbon dioxide lies in the fact that it dissolves in the oil which in turn reduces the oil viscosity, and thus, increases its mobility. The improved mobility of the oil allows for an extraction of the otherwise trapped oil. Here, an interphase mass transfer process (dissolution) is responsible for an improved recovery. (d) The last example (Fig. 2 (d)) shows the upper part of the soil. The water balance of this part of the subsurface is extremely important for agriculture or plant growth in general. Plants do not grow well under too wet or too dry conditions. One of the very important factors influencing this water balance (besides surface runoff and infiltration) is the evaporation of water from the soil, which is again an interphase mass transfer process. 1.2 Purpose of this work
Mass transfer processes are essential in a large variety of applications—the presented examples only show a small selection of systems. A common feature of all these applications is the fact that the relevant processes occur in relatively large domains such that it is not possible to resolve the pore structure and the fluid distribution in detail (left hand side of Fig. 3). Instead, a macro-scale approach is needed where properties and processes are averaged over a so-called representative elementary volume (right hand side of Fig. 3). This means that the common challenge in all of the above-mentioned applications is how to describe mass transfer processes on a macro scale. This transition from the pore scale to the macro scale is illustrated in Fig. 3 where on the left side, the pore-scale situation is shown (which is impossible to be resolved in detail) while on the right hand side, the macro-scale situation is shown.
2. Overview of classical mass transfer descriptions 2.1 Pore-scale considerations
In order to better understand the physics of interphase mass transfer, which is essential to provide a physically-based description of this process, we start our considerations on the pore
4 4
Transfer Mass Transfer in Multiphase Systems andMass its Applications
n
w
non−wetting fluid phase
wetting fluid phase
s
solid phase
macro scale
pore scale
Fig. 3. Pore-scale versus macro-scale description of flow and transport in a porous medium. scale. From there, we try to get a better understanding of the macro-scale physics of mass transfer, which is our scale of interest. In Fig. 1 we have seen that interphase mass transfer is inherently a pore-scale process as it—naturally—takes place across fluid–fluid interfaces. Let us imagine a situation where two fluid phases, a wetting phase and a non-wetting phase, are brought in contact as shown in Fig. 4. Commonly, when the two phases are brought in contact (time t = t0 ), equilibrium is quickly established directly at the interface. With respect to mass transfer, this means that the concentration of non-wetting phase particles in the wetting phase at the interface as well as the concentration of wetting-phase particles in the non-wettting phase at the interface are 2 1 . At t = t , away from the interface, there both at their equilibrium values, C1,eq and C2,eq 0 is still no presence of α-phase particles in the β-phase. At a later time t = t1 , concentration profiles develop within the phases. However, within the bulk phases, the concentrations are still different from the respective equilibrium concentration at the interface. Considering a still later point of time, t = t2 , the equilibrium concentration is finally reached everywhere in the bulk phases. These considerations show that mass transfer on the pore scale is inherently a kinetic process that is very much related to phase-interfaces. But how is this process represented on the macro scale, i.e. on a volume-averaged scale? This is what we will focus on in the next section. t = t0
t = t1
t = t2
solid phase
solid phase
solid phase
fluid phase 1
fluid phase 1
fluid phase 2
C
C
fluid phase 2
C 2
2
C1,eq
C1,eq
2
C1,eq
fluid phase 1
fluid phase 2
1
C2,eq
1
C2,eq
1
C2,eq
x
Fig. 4. Pore-scale picture of interphase mass transfer.
x
x
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
55
2.2 Current macro-scale descriptions
In Fig. 3, we illustrated the fact that when going from the pore scale to the macro scale, information about phase-interfaces is lost. The only information present on the macro scale is related to volume ratios, such as porosity and fluid saturations. But, as mentioned earlier, mass transfer is strongly linked to the presence of interfaces and interfacial areas and all the information about phase-interfaces disappears on the macro scale. This means that the description of mass transfer on the macro scale is not straight forward. Classical approaches for describing mass transfer generally rely on one of the following two principles: 1. assumption of local chemical equilibrium within an averaging volume or 2. kinetic description based on a fitted (linear) relationship. These two classical approaches will be discussed in more detail in the following. An alternative approach which accounts for the phase-interfacial area will be presented later in Sec. 3. 2.2.1 Local equilibrium assumption
The assumption of local chemical equilibrium within an averaging volume means that the equilibrium concentrations are reached instantaneously everywhere within an averaging volume (in both phases). That means it is assumed that everywhere within the averaging volume, the situation at t = t2 in Fig. 4 is reached from the beginning (t = t0 ). Thus, at each point in the wetting phase and at each point in the non-wetting phase within the averaging volume, the equilibrium concentration of the components of the other phase is reached. This is an assumption which may be good in case of fast mass transfer, but bad in case of slow mass transfer processes. To be more precise, the assumption that the composition of a phase is at or close to equilibrium may be good if the characteristic time of mass transfer is small compared to that of flow. However, if large flow velocities occur as e.g. during air sparging, the local equilibrium assumption gives completely wrong results, see Falta (2000; 2003) and van Antwerp et al. (2008). We will investigate and quantify this issue later in Sec. 3.3 . Local equilibrium models for multi-phase systems have been introduced and developed e.g. by Miller et al. (1990); Powers et al. (1992; 1994); Imhoff et al. (1994); Zhang & Schwartz (2000) and have been used and advanced ever since. Let us consider a system with a liquid phase (denoted by subscript l) and a gaseous phase (denoted by subscript g) composed of air and water components. Then, Henry’s Law is employed to determine the mole fraction of air in the liquid phase, while the mole fraction of water in the gas phase is determined by assuming that the vapor pressure in the gas phase is equal to the saturation vapor pressure. Denoting the water component by superscript w and the air component by superscript a, this yields xla xw g
= =
p ag · Hla− g
(1)
pw sat
(2)
pg
,
where xla [−] is the mole fraction of air in the liquid phase, x w g [−] is the mole fraction of water 1 a in the gaseous phase, Hl − g Pa is the Henry constant for the dissolution of air in the liquid a phase, pw sat [ Pa ] is the saturation vapor pressure of water, p g [ Pa ] is the partial pressure of air
6 6
Transfer Mass Transfer in Multiphase Systems andMass its Applications
in the gas phase while p g [ Pa] is the gas pressure. The remaining mole fractions result simply from the condition that mole fractions in each phase have to sum up to one, xlw x ga
= =
1 − xla
(3)
1−
(4)
xw g.
Note that while for a number of applications the equilibrium mole fractions are constants or merely a function of temperature, in our case, they will be functions of space and time as pressure and the composition of the phases changes. 2.2.2 Classical kinetic approach
Kinetic mass transfer approaches are traditionally applied to the dissolution of contaminants in the subsurface which form a separate phase from water, the so-called non-aqueous phase liquids (NAPLs). If such a non-aqueous phase liquid is heavier than water, it is called “dense non-aqueous phase liquid” or DNAPL. When an immobile lense of DNAPL is present at residual saturation (i.e. at a saturation which is so low that the phase is immobile) and dissolves into the surrounding groundwater, the kinetics of this mass transfer process usually plays an important role: the dissolution of DNAPL is a rate-limited process. This is also the case when a pool of DNAPL is formed on an impermeable layer. In these relatively simple cases, only the mass transfer of a DNAPL component from the DNAPL phase into the water phase has to be considered. For these cases, classical models acknowledge the fact that the rate of mass transfer is highly dependent (proportional to) interfacial area and assume a first-order rate of kinetic mass transfer between fluid phases in a porous medium on a macroscopic (i.e. volume-averaged) scale which can be expressed as (see e.g. Mayer & Hassanizadeh (2005)): κ Qκα→ β = kκα→ β aαβ (Cβ,s − Cβκ ), (5) kg where Qκα→ β m3 s is the interphase mass transfer rate of component κ from phase α to phase β, kκα→ β ms is the mass transfer rate coefficient, aαβ m1 is the specific interfacial kg κ area separating phases α and β, Cβ,s is the solubility limit of component κ in phase m3 kg β, and finally, Cβκ m3 is the actual concentration of component κ in phase β. The actual κ . The case C κ = C κ corresponds concentration is not larger than the solubility limit, Cβκ ≤ Cβ,s β β,s to the local equilibrium case. In the absence of a physically-based estimate of interfacial area in classical kinetic models, the mass transfer coefficient kκα→ β and the specific interfacial area aαβ are often lumped into one single parameter (Miller et al. (1990); Powers et al. (1992; 1994); Imhoff et al. (1994); Zhang & Schwartz (2000)). This yields, in a simplified notation, Q = k (Cs − C ).
(6)
Here, Cs is the solubility limit of the DNAPL component in water and C is its actual 1 concentration. The lumped mass transfer coefficient k s is commonly related to a modified Sherwood number Sh by Dm (7) k = Sh 2 , d50
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
77
2 where Dm ms is the aqueous phase molecular diffusion coefficient, and d50 [m] is the mean size of the grains. The Sherwood number is then related to Reynold’s number Re and DNAPL saturation Sn [−] by Sh = pReq Snr , (8) where p, q, and r are dimensionless fitting parameters. This is a purely empirical relationship. Although interphase mass transfer is proportional to specific interfacial area in the original Eq. (5), this dependence cannot explicitly be accounted for as the magnitude of specific interfacial area is not known. An alternative classical approach for DNAPL pool dissolution has been proposed by Falta (2003) who modeled the dissolution of DNAPL component by a dual domain approach for a case with simple geometry. For this purpose, they divided the contaminated porous medium into two parts: one that contains DNAPL pools and one without DNAPL. For their simple case, the dual domain approach combined with an analytical solution for steady-state advection and dispersion provided a means for modeling rate-limited interphase mass transfer. While this approach provided good results for the case of simplified geometry, it might be oversimplified for the modeling of realistic situations.
3. Interfacial-area-based approach for mass transfer description 3.1 Theoretical background
Due to a number of deficiencies of the classical model for two-phase flow in porous media (one of which is the problem in describing kinetic interphase mass transfer on the macro scale), several approaches have been developed to describe two-phase flow in an alternative and thermodynamically-based way. Among these are a rational thermodynamics approach by Hassanizadeh & Gray (1980; 1990; 1993b;a), a thermodynamically constrained averaging theory approach by Gray and Miller (e.g. Gray & Miller (2005); Jackson et al. (2009)), mixture theory (Bowen (1982)) and an approach based on averaging and non-equilibrium thermodynamics by Marle (1981) and Kalaydjian (1987). While Marle (1981) and Kalaydjian (1987) developed their set of constitutive relationships phenomenologically, Hassanizadeh & Gray (1990; 1993b); Jackson et al. (2009), and Bowen (1982) exploited the entropy inequality to obtain constitutive relationships. To the best of our knowledge, the two-phase flow models of Marle (1981); Kalaydjian (1987); Hassanizadeh & Gray (1990; 1993b); Jackson et al. (2009) are the only ones to include interfaces explicitly in their formulation allowing to describe hysteresis as well as kinetic interphase mass and energy transfer in a physically-based way. In the following, we follow the approach of Hassanizadeh & Gray (1990; 1993b) as it includes the spatial and temporal evolution of phase-interfacial areas as parameters which allows us to model kinetic interphase mass transfer in a much more physically-based way than is classically done. It has been conjectured by Hassanizadeh & Gray (1990; 1993b) that problems of the classical two-phase flow model, like the hysteretic behavior of the constitutive relationship between capillary pressure and saturation, are due to the absence of interfacial areas in the theory. Hassanizadeh and Gray showed (Hassanizadeh & Gray (1990; 1993b)) that by formulating the conservation equations not only for the bulk phases, but additionally for interfaces, and by exploiting the residual entropy inequality, a relationship between capillary pressure, saturation, and specific interfacial areas (interfacial area per volume of REV) can be derived. This relationship has been determined in various experimental works (Brusseau et al. (1997); Chen & Kibbey (2006); Culligan et al. (2004); Schaefer et al. (2000); Wildenschild et al. (2002);
8 8
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Chen et al. (2007)) and computational studies (pore-network models and CFD simulations on the pore scale, see Reeves & Celia (1996); Held & Celia (2001); Joekar-Niasar et al. (2008; 2009); Porter et al. (2009)). The numerical work of Porter et al. (2009) using Lattice Boltzman simulations in a glass bead porous medium and experiments of Chen et al. (2007) show that the relationship between capillary pressure, the specific fluid-fluid interfacial area, and saturation is the same for drainage and imbibition to within the measurement error. This allows for the conclusion that the inclusion of fluid–fluid interfacial area into the capillary pressure–saturation relationship makes hysteresis disappear or, at least, reduces it down to a very small value. Niessner & Hassanizadeh (2008; 2009a;b) have modeled two-phase flow—using the thermodynamically-based set of equations developed by Hassanizadeh & Gray (1990)—and showed that this interfacial-area-based model is indeed able to model hysteresis as well as kinetic interphase mass and also energy transfer in a physically-based way. 3.2 Simplified model
After having presented the general background of our interfacial-area-based model, we will now proceed by discussing the mathematical model. The complete set of balance equations based on the approach of Hassanizadeh & Gray (1990) is too large to be handled numerically. In order to do numerical modeling, simplifying assumptions need to be made. In the following, we present such a simplified equation system as was derived in Niessner & Hassanizadeh (2009a). This set of balance equations can be described by six mass and three momentum balance equations. These numbers result from the fact that mass balances for each component of each phase and the fluid–fluid interface (that is 2 × 3) while momentum balances are given for the bulk phases and the interface. Governing equations were derived by Hassanizadeh & Gray (1979) and Gray & Hassanizadeh (1989; 1998) for the case of flow of two pure fluid phases with no mass transfer. Extending these equations to the case of two fluid phases, each made of two components, we obtain the following equations. mass balance for phase components (κ = w, a): ∂ φSl ρ¯ l X¯ lκ κ + ∇ · (φSl ρ¯ l X¯ lκ v¯l ) − ∇ · φSl j¯l ∂t
1 κ = ρ¯ l Ql + (9) ρl Xlκ vlg − vl + jκ · nlg dA l V Alg ∂ φSg ρ¯ g X¯ gκ κ + ∇ · φSg ρ¯ g X¯ gκ v¯ g − ∇ · φSg j¯g ∂t
1 κ = ρ¯ g Q g + (10) ρ g Xgκ v g − vlg − jκ · nlg dA g V Alg mass balance for lg-interface components (κ = w, a): κ a ∂ Γ¯ lg X¯ lg lg κ κ + ∇ · Γ¯ lg X¯ lg alg v¯ lg − ∇ · j¯ alg − lg ∂t
1 ρl Xlκ vl − vlg − jκ − ρ g Xgκ v g − vlg + jκ · nlg dA = l g V Alg
(11)
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
99
momentum balance for phases:
=
=
∂ (φSl ρ¯ l v¯ l ) + ∇ · (φSl ρ¯ l v¯l v¯l ) − ∇ · (φSl T l ) ∂t
1 ρl vl vlg − vl + tl · nlg dA V Alg ∂ φSg ρ¯ g v¯ g + ∇ · φSg ρ¯ g v¯ g v¯ g − ∇ · φSg T g ∂t
1 ρ g v g v g − vlg − t g · nlg dA V Alg
momentum balance for lg-interface: ∂ Γ¯ lg v¯ lg alg + ∇ · Γ¯ lg v¯lg alg v¯lg − ∇ · T lg alg ∂t
1 = ρl vl vl − vlg − tl − ρ g v g v g − vlg + t g · nlg dA, V Alg
(12)
(13)
(14)
κ where the overbars denote volume-averaged (macro-scale) 3 quantities. Here, Xα [−] is the mass fraction of component κ in phase α, t is time, Qκα ms is an external source of component kg·m4 κ in phase α, jκ is the diffusive flux of component κ in phase α, V is the magnitude of s α the averaging volume, Alg denotes the interfaces separating the l-phase and the g-phase in an averaging volume, vlg ms is the velocity of the lg-interface, and nlg is the unit vector normal κ [−] is the mass fraction of component κ to Alg and pointing into the g-phase. Furthermore, Xlg 4 kg · m kg is the diffusive flux of component κ in the lg-interface, tα m·s2 in the lg-interface, jκ s lg kg is the α-phase micro-scale stress tensor, T α s2 is the α-phase macro-scale stress tensor, and kg T lg s2 is the macro-scale lg-interfacial stress tensor. In the following, we provide a simplified version of Eq. (9) through (14). First, we assume that the composition of the interface does not change. This is a reasonable assumption as long as no surfactants are involved. This reduces the number of balance equations to eight, as we can sum up the mass balance equations for interface components. Furthermore, we assume that momentum balances can be simplified so far that we end up with Darcy-like equations for both bulk phases and interface. We further proceed by applying Fick’s law to relate the micro-scale diffusive fluxes jκ to the local concentration gradient resulting in the following α approximation: κ ρα Dκ jκ · nlg = ± κ alg Xα,s − Xακ , (15) α d 2 where Dκ ms is the micro-scale Fickian diffusion coefficient for component κ, dκ [m] is the κ [−] is the solubility limit of component κ in phase α diffusion length of component κ, Xα,s (i.e. the mass fraction corresponding to local equilibrium), and Xακ [−] is the micro-scale mass fraction of component κ in phase α at a distance dκ away from the interface. Niessner &
10 10
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Hassanizadeh (2009a) obtained the following determinate set of macro-scale equations: ∂ φSl ρ¯ l X¯ lw w + ∇ · (ρ¯ l X¯ lw v¯l ) − ∇ · j¯l ∂t D w ρ¯ g w w = ρl Qw l − dw alg X g,s − X g ∂ φSl ρ¯ l X¯ la a + ∇ · (ρ¯ l X¯ la v¯l ) − ∇ · j¯l ∂t D a ρ¯ a = ρl Qla + a l alg Xl,s − Xla d ∂ φSg ρ¯ g X¯ gw w + ∇ · ρ¯ g X¯ gw v¯ g − ∇ · j¯g ∂t D w ρ¯ g w = ρ g Qw alg Xg,s − Xgw g + w d a ¯ ∂ φSg ρ¯ g Xg a + ∇ · ρ¯ g X¯ ga v¯ g − ∇ · j¯g ∂t D a ρ¯ a = ρ g Q ag − a l alg Xl,s − Xla d ∂alg + ∇ · alg vlg = Elg ∂t S2 v¯ l = −K l ∇ pl − ρ¯ l g μl S2g v¯ g = −K ∇ p g − ρ¯ g g μg
(17)
(18)
(19) (20) (21) (22)
−Klg ∇ alg p g − pl 1 1 1
(23)
+ Xla + Xga
= = = = =
alg
=
alg (Sl , pc ),
(28)
v¯ lg pc Sl + S g Xlw Xgw
(16)
(24) (25) (26) (27)
κ α
The macro-scale mass fluxes j¯ are given by a Fickian dispersion equation, κ ¯ ακ ∇ ( X¯ ακ ) , j¯ = −ρα D α
(29)
¯ ακ is the macro-scale dispersion coefficient. Note that in Eq. (16) through (19), we where D have acknowledged the fact that an internal source of a component in one of the phases must correspond to a sink of that component of equal magnitude in the other phase. The w and X a are obtained from a local equilibrium assumption at the solubility limits Xg,s l,s fluid–fluid interface. If, for example, we consider a two-phase–two-component air–water system solubility limits with respect to mole fractions are given by Eqs. (1) and (2).
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
11 11
3.3 Is a kinetic approach necessary?
Depending on the parameters, initial conditions, and boundary conditions of the system, kinetics might be important for mass transfer. If so, then it may not be sufficient to use a classical local equilibrium model instead of the more complex interfacial-area-based model. To allow for a decision, Niessner & Hassanizadeh (2009a) make the system of equations (16) ¨ through (28) dimensionless and study the dependence of kinetics on Damkohler number and Peclet number. To do so, they define dimensionless variables: t∗
=
a∗lg
=
∗ Elg
=
p∗α
=
tv R , φL alg a R,lg
∇ ∗ = L ∇,
vR pα , pR
¯κ ¯ ακ ∗ = Dα , D DR,α
,
a R,lg φL
v¯ ∗α =
g∗ =
Elg ,
α
p∗c =
pc , pR
v¯ α , vR
v∗lg =
ρ¯ α gL pR
Qκα L κ v , Xα,s R
(30)
φ v , v R lg
∗ Klg =
,
ρ∗g =
Qκα∗ =
ρ¯ g ρ¯ l
(31) φKlg
La R,lg v R
μ∗l =
,
(32)
μl . μg
(33)
Here, ρ∗g is density ratio, μ∗l is viscosity ratio, v R is a reference velocity, L is a characteristic length, a R,lg is a reference specific interfacial area, DR,α is a reference dispersion coefficient, and p R is a reference pressure. We assume that p R and v R can be chosen such that ¨ Also, Peclet number Peα and Damkohler number Daκ are defined by Peα =
vR L , DR,α
Daκ =
Dκ La R,lg dv R
.
Kp R μl v R L
= 1.
(34)
These definitions lead to the following dimensionless form of Eq. (16) through (28): w∗ Dl ∂ w ∗ w ∗ ∗ ∗ ¯w ∗ w ¯ ¯ + ∇ − ∇ S · v · ∇ = Qw − Daw a∗lg ρ∗g Xg,s − X¯ gw (35) X X X ( ) ) ( l l l l l l ∗ ∂t Pel a∗ Dl ∂ ∗ ¯a a∗ a ∗ a ¯ a ) + ∇∗ · ( X¯ a v∗ ) − ∇∗ · ¯a S ∇ = Q + Da a − X X X X (36) ( l l lg l l l l,s l l ∂t∗ Pel
w∗ Dg ∂ ¯ w ∗ ∗ ¯w w∗ w ∗ w ¯ gw (37) ¯ gw v∗g − ∇∗ · + ∇ · ∇ = Q + Da a − X X X S X X g g g g g,s lg ∂t∗ Peg
a∗ Dg ∂ ¯ a 1 a ∇∗ X¯ ga = Q ag∗ − Daa a∗lg ∗ Xl,s − X¯ la (38) Sg Xg + ∇∗ · X¯ ga v∗g − ∇∗ · ∗ ∂t Peg ρg ∂a∗lg ∂t∗
+ ∇∗ · a∗lg v∗lg
=
∗ Elg
v∗l
=
v∗g
=
−Sl2 ∇∗ p∗l − g∗l −S2g μ∗l ∇∗ p∗g − g∗g
(39) (40) (41)
12 12
Transfer Mass Transfer in Multiphase Systems andMass its Applications
v∗lg
=
∗ ∗ ∗ −Klg ∇ alg
(42)
p∗c
= = = =
p∗g − p∗l
(43)
1
(44)
1
(45)
1
(46)
a∗lg (Sl , p∗c ) .
(47)
Sl + S g X¯ lw + X¯ la X¯ gw + X¯ ga a∗lg
=
In order to investigate the importance of kinetics, we define Pe := Pel = Peg and Da := Daw = Daa and vary Pe and Da independently over five orders of magnitude. Therefore, we consider a numerical example where dry air is injected into a horizontal (two-dimensional) porous medium of size 0.7 m × 0.5 m that is almost saturated with water (initial and boundary water saturation of 0.9). a Fig. 5 shows a comparison of actual mass fractions X¯ la and X¯ gw to solubility mass fractions Xl,s w ¨ and Xg,s for five different Damkohler numbers. Therefore, a cut through the domain is shown and two different time steps are compared. Da=0.1 Da0
Da=0.01 Da0 4.0E-5 4E−5
Da=Da0
4.0E-5 4E−5
Da=10 Da0
4.0E-5 4E−5
Da=100 Da0
4.0E-5 4E−5
4.0E-5 4E−5
a
Xl [−]
t = 0.0035s
0m
x 0.7m 0.7
00 0.014 0.014
0m
x 0.7m 0.7
00m 0
x 0.7m 0.7
00m 0
x 0.7m 0.7
00 0.014 0.014
0m
x 0.7m 0.7
0m
x 0.7m 0.7
00m 0
x 0.7m 0.7
00m 0
x 0.7m 0.7
00 0.014 0.014
00 0.014 0.014
00m 0 0.014 0.014
x 0.7m 0.7
w
Xg [−]
4.0E-5 4E−5
4.0E-5 4E−5
4.0E-5 4E−5
4.0E-5 4E−5
00m 0
x 0.7m 0.7
4.0E-5 4E−5
a
Xl [−] 00m 0
t = 0.01s
x 0.7m 0.7
0.014 0.014
00m 0
x 0.7m 0.7
0.014 0.014
00m 0
x 0.7m 0.7
0.014 0.014
00m 0
x 0.7m 0.7
0.014 0.014
00m 0
x 0.7m 0.7
0.014 0.014
w
Xg [−] 00m 0
x
0.7m
0.7
00m 0
x
0.7m
0.7
00m 0
x
0.7m
0.7
00m 0
x
0.7m
0.7
00m 0
x
0.7m
0.7
solubility limit actual mass fraction
a and X w and actual mass fractions X ¯ a and X¯ gw for two different Fig. 5. Solubility limits Xl,s g,s l ¨ time steps (0.0035 s and 0.01 s) and 5 different Damkohler numbers.
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
13 13
It can be seen that the system is practically instantaneously in equilibrium with respect to the mass fraction X¯ gw (water mass fraction in the gas phase) for the whole range of considered ¨ Damkohler numbers (see the second and forth row of graphs). With respect to the mass ¨ numbers and early times, fraction X¯ la (air mass fraction in the water phase), for low Damkohler the system is far from equilibrium (see the first and third row of graphs). With increasing ¨ time and with increasing Damkohler number, the system approaches equilibrium. As for ¨ high Damkohler numbers mass transfer is very fast, an ”overshoot“ occurs and the system becomes oversaturated before it reaches equilibrium. One might argue that the considered time steps are extremely small and not relevant for the time scale relevant for the whole domain. However, what happens at this very early time has a large influence on the state of the system at all subsequent times. It turned out that for different Peclet numbers, there is no difference in results. That means that kinetic interphase mass transfer is independent of Peclet number, at least within the four orders of magnitude considered here.
4. Extension to heat transfer The concept of describing mass transfer based on modeling the evolution of interfacial areas using the thermodynamically-based approach of Hassanizadeh & Gray (1990; 1993b) can be extended to describing interphase heat transfer as well. The main difference between interphase mass and heat transfer is that, in addition to fluid–fluid interfaces, heat can also be transferred across fluid–solid interfaces, see Fig. 6. Similarly to mass transfer, classical two-phase flow models describe heat transfer on the macro scale by either assuming local thermal equilibrium within an averaging volume or by formulating empirical models to describe the transfer rates. The latter is necessary as classically, both fluid–fluid and fluid–solid interfacial areas are unknown on the macro scale. And similiarly to mass transfer, we can use the thermodynamically-based approach of Hassanizadeh & Gray (1990; 1993b) which includes both fluid–fluid and fluid–solid interfacial areas in order to describe mass transfer in a physically-based way. We can
(1)
(2)
wetting non−wetting
mass transfer
wetting non−wetting
heat transfer
Fig. 6. Mass transfer takes place across fluid–fluid interfaces (left hand side) and heat transfer across fluid–fluid as well as fluid–solid interfaces (right hand side)
14 14
Transfer Mass Transfer in Multiphase Systems andMass its Applications
also perform a dimensional analysis and derive dimensionless numbers that help to decide whether kinetics of heat transfer needs to be accounted for or whether a local equilibrium model is sufficiently accurate on the macro scale. For more details on these issues, we refer to Niessner & Hassanizadeh (2009b).
5. Macro-scale example simulations For the numerical solution of the system of Eq.s (16) through (28), we use a fully-coupled vertex-centered finite element method (an in-house code) which not only conserves mass locally, but is also applicable to unstructured grids. For time discretization, a fully implicit Eulerian approach is used, see e.g. Bastian et al. (1997); Bastian & Helmig (1999). The nonlinear system is linearized using a damped inexact Newton-Raphson solver, and the linear system is subsequently solved using a Bi-Conjugate Gradient Stabilized method (known as BiCGStab method). Full upwinding is applied to the flux terms of the bulk phase equations, but in the interfacial area flux term, central weighting is used. 5.1 Evaporator
As a simulation example, we consider a setup which is relevant in many industrial processes where a product needs to be concentrated (e.g. foods, chemicals, and salvage solvents) or dried through evaporation of water. The aqueous solution containing the desired product is fed into the evaporator mostly consisting of micro-channels and then passes a heat source. Heat converts the water in the solution into vapor and the vapor is subsequently removed from the solution. We model the heating and evaporation process through a setup as shown in Fig. 7. This means we consider a horizontal domain that is closed along the sides (top and bottom in the figure) and that is subjected to a gradient in wetting phase pressure from left to right in the undisturbed situation. This system is assumed to be at the following initial conditions: a temperature of 293 K, gas phase at atmospheric pressure, water saturation of 0.9, a corresponding capillary pressure based on the primary drainage curve, and mass fractions that correspond to the local chemical equilibrium conditions as prescribed by Henry’s Law ¨ ¨ and Raoult’s Law (Ludecke & Ludecke (2000)). The porous medium is heated with a rate of Qs in a square-shaped part of the domain, causing the evaporation of water (see Fig. 7). Note that the heat source heats up only the walls of the microchannels (the solid phase) and the heat is then transferred from the solid phase to the water phase.
Sil = 0.9 pgi = 106875 Pa pci = pcdr (0.9) ai a Xl = Xl,s (pgi , Til ) w (p i , Ti ) Xwg i = Xg,s g g Tli = 293.15 K i Tg = 293.15 K Tsi = 293.15 K
Sil = 0.9 pgi = 101325 Pa pci = pcdr (0.9) ai a Xl = Xl,s (pgi , Tli ) w Xwg i = Xg,s (pgi , Tni ) Tli = 293.15 K Tgi = 293.15 K Tsi = 293.15 K
Qs
Sil = 0.9 pgi = 101325 Pa pci = pcdr (0.9) a i i Xai l = Xl,s (pg , Tl ) w Xwg i = Xg,s (pgi , Tgi ) Tli = 293.15 K Tgi = 293.15 K Tsi = 293.15 K
0.5 m
0.7 m
Fig. 7. Setup of the numerical example: water passes a heat source and is evaporated.
15 15
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
For comparison, the same setup is used for simulations using a classical two-phase flow model, where—in the absence of interfacial areas as parameters—local chemical and thermal equilibrium is assumed. This means that the heat source cannot be defined for the solid phase only; instead, the applied heat will instantaneously lead to a heating of all three phases. The distribution of water saturation and water–gas specific interfacial area are shown in Fig. 8 at the time of 17 seconds after the heat source is switched on. The saturation distribution given by the interfacial area-based model is compared to that of the classical model. Obviously, water saturation decreases in the heated region due to the evaporation of water. Downstream of the heated zone, water saturation increases indicating that in the colder regions, water condenses again. Due to the decrease in water saturation, gas–water interfacial areas are created. The classical model predicts a much lower decrease in water saturation in the heated region. Fig. 9 shows the mass fraction of air dissolved in the liquid phase after 17 seconds. There, also the equilibrium value (solubility limit) predicted by the interfacial area-based model is shown. Clearly, chemical non-equilibrium effects occur, but the classical model predicts approximately the same result as the equilibrium values in the interfacial area-based model. This is due to the fact that the classical two-phase flow approach always assumes local equilibrium and can only represent mass fractions corresponding to the equilibrium values. The analogous comparison is shown in Fig. 10 with respect to the mass fractions of vapor in the gas phase. Here, the mass fractions in the interfacial area-based model are very close to the equilibrium values, but larger differences to the classical model can be detected.
Sl from interfacial area model
Sw:
0.8 0.81 0.82 0.83 0.84 0.85 0.86 0.87 0.88 0.89 0.9 0.91
Sl from classical model
S l Sw:
alg from interfacial area model
awn: a lg [1/m]
0.8 0.81 0.82 0.83 0.84 0.85 0.86 0.87 0.88 0.89 0.9 0.91
380 400 420 440 460 480 500 520 540 560 580
Fig. 8. Water saturation and water–gas specific interfacial area after 17s. a
Xl from interfacial area model
a
a
Xl,s from interfacial area model
Xl from classical model
a
Xsw2 2.36E-05 2.34E-05 2.32E-05 2.3E-05 2.28E-05 2.26E-05 2.24E-05 2.22E-05 2.2E-05 2.18E-05 2.16E-05 2.14E-05
Xl
2.36E.6
2.24E−6
Fig. 9. Mass fraction of air in the liquid phase after 17s. Left: results using the interfacial area-based model, middle: equilibrium values given by the interfacial area-based model, right: results given by the classical model.
16 16
Transfer Mass Transfer in Multiphase Systems andMass its Applications
w
Xw g from interfacial area model
w
Xg,s from interfacial area model
Xg from classical model
w
X g [−]
Xsn1
XWG
0.75 0.7 0.65 0.6 0.55 0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05
0.75 0.7 0.65 0.6 0.55 0.5 0.45 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05
Fig. 10. Mass fractions of vapor in the gas phase after 17s. Left: results using the interfacial area-based model, middle: equilibrium values given by the interfacial area-based model, right: results given by the classical model. Fig. 11 shows the temperatures of the three phases (liquid l, gas g, solid s) after 17s using the interfacial area-based model and the classical model. It can be seen that a lower temperature rise is predicted by the classical model than by the interfacial area-based model. T l from interfacial area model
T g from interfacial area model
T s from interfacial area model
T from classical model T[K]Te
Tn
375 370 365 360 355 350 345 340 335 330 325 320 315 310 305 300 295
375 370 365 360 355 350 345 340 335 330 325 320 315 310 305 300 295
Fig. 11. Temperatures of the phases after 17s using the interfacial area-based model (three pictures on left) and the classical model (right picture). Fig. 12 shows the temperature differences between the phases using the interfacial area-based model. We find that there are differences of up to 8 K between the phases. The classical two-phase model assumes local thermal equilibrium, i.e. Tw = Tn = Ts . In reality, however, the heat exchange between the phases is restricted by the respective interfacial areas and the heat equalization does not take place instantaneously. Tl
− Tg
T[K] dTwTn -0.5 -1 -1.5 -2 -2.5 -3 -3.5 -4 -4.5 -5 -5.5 -6 -6.5 -7 -7.5 -8
Tg − Ts
T[K] dTnTs 0 -0.2 -0.4 -0.6 -0.8 -1 -1.2 -1.4 -1.6 -1.8 -2 -2.2 -2.4 -2.6 -2.8 -3 -3.2 -3.4
Fig. 12. Temperatures differences between wetting and non-wetting phase (left hand side) and between non-wetting and solid phase (right hand side) after 17s.
17 17
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling 5.2 Drying of a porous medium
As a second example, we consider the drying of an initially almost water-saturated porous medium through injection of hot dry air (50 ◦ C). This process is relevant in the textile, construction, and paper industries as well as in medical applications. The setup is shown in Fig. 13. For comparison, this setup is also simulated using the classical model. Note that in the classical model, due to the assumption of local chemical and thermal equilibrium, it is impossible to apply a source of hot dry air. Instead, the air supplied to the system instantaneously redistributes among the phases in order to yield equilibrium composition. The temperature of the air source will instantaneously heat up all three phases.
Sil = 0.9 pgi = 101475 Pa pci = pcdr (0.9) ai a Xl = Xg,s (pgi , Til ) w (p i , Ti ) Xwg i = Xg,s g g Tli = 293 K Tgi = 293 K Tsi = 293 K
Sil = 0.9 pgi = 101325 Pa pci = pcdr (0.9) a i i Xai l = Xl,s (pg , Tl ) w (pi , Ti ) Xwg i = Xg,s g g Tli = 293 K Tgi = 293 K Tsi = 293 K
a Sil = 0.9 Qn pgi = 101325 Pa T = 333 K pci = pcdr (0.9) ai a i i Xl = Xl,s (pg, Tl ) w i , Ti ) Xwi g = Xg,s (pg g Tli = 293 K i Tg = 293 K Tsi = 293 K
0.5 m
0.7 m
Fig. 13. Setup of the numerical example: drying of a porous medium through injection of warm dry air. Fig. 14 shows the water saturation and the specific gas–water interfacial area after 12 seconds. The water saturation decreases due to the gas injection and interfaces are produced. The saturation distribution is different if the classical model is used. This may be due to the fact that the source term needs to be specified differently for the two models (see the above comments on the problem description). Sl from interfacial area model
Sl from classical model Sw
0.89 0.88 0.87 0.86 0.85 0.84 0.83 0.82 0.81 0.8 0.79 0.78 0.77 0.76 0.75 0.74 0.73 0.72
SSw l 0.89 0.88 0.87 0.86 0.85 0.84 0.83 0.82 0.81 0.8 0.79 0.78 0.77 0.76 0.75 0.74 0.73 0.72
alg from interfacial area model
a lg awn[1/m] 600 580 560 540 520 500 480 460 440 420
Fig. 14. Water saturation (using both interfacial area-based and classical model) and specific fluid–fluid interfacial area using the interfacial area-based model after 12s. In Fig. 15, the mass fraction of air disolved in the water phase is shown after 12s. The actual mass fraction distribution using the interfacial-area-based approach is shown in the left picture. The mass fraction corresponding to local chemical equilibrium is shown in the middle figure. For comparison, the mass fraction distribution resulting from the classical model is shown in the right figure. Obviously, significant deviations from equilibrium can be detected. This implies that chemical non-equilibrium is very important in this example. The
18 18
Transfer Mass Transfer in Multiphase Systems andMass its Applications
a
a
a
Xl from interfacial area model
Xl,s from interfacial area model
Xl from classical model
a
XXAW l
XAW 2.348E-05 2.347E-05 2.346E-05 2.345E-05 2.344E-05 2.343E-05 2.342E-05 2.341E-05
2.348E-05 2.347E-05 2.346E-05 2.345E-05 2.344E-05 2.343E-05 2.342E-05 2.341E-05
Fig. 15. Mass fractions of air in water. Left: interfacial-area-based model, actual mass fractions; middle: equilibrium mass fractions. Right: classical model. equilibrium mass fractions of the interfacial area-based model are also very different from that predicted by the classical model, probably due to the differently specified source. Fig. 16 shows the same for water vapor in the gas phase. Here, the deviation from chemical equilibrium is also significant, but the equilibrium mass fractions using the interfacial area-based model and the classical model are very similar.
Xw g from interfacial area model
Xwg,s from interfacial area model
w
Xg from classical model
w
XWG
XXWG g [−]
0.0175 0.017 0.0165 0.016 0.0155 0.015
0.0175 0.017 0.0165 0.016 0.0155 0.015
Fig. 16. Mass fractions of vapor in the gas phase. Left: interfacial-area-based model, actual mass fractions; middle: equilibrium mass fractions. Right: classical model. In Fig. 17, the temperatures of the three phases (liquid l, gas g, and solid phase s) resulting from the interfacial area-based model are shown and compared to the temperature given by the classical model. Unlike the mass fractions, the temperatures are not very far from equilibrium (maximum difference in phase temperatures is approximately 0.17 K, see also Fig. 18). An interesting aspect is that the temperature difference is lower in the middle of the injection zone than in the surrounding area. This is due to the fact that specific interfacial area is at a maximum in this middle part leading to higher heat transfer rates in this region and phase temperature closer to each other and thus, closer to thermal equilibrium.
6. Summary and conclusions In this chapter, the issue of interphase mass transfer during two-phase flow in a porous medium has been discussed. Starting from pore-scale considerations, the classical approaches for describing mass transfer have been presented which—due to the absence of interfacial area as a parameter—either assume local equilibrium within an averaging volume or use empirical approaches to describe the kinetics.
19 19
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
T l from interfacial area model
T g from interfacial area model
T s from interfacial area model
T from classical model T[K] Te
Ts
296.4 296.2 296 295.8 295.6 295.4 295.2 295 294.8 294.6 294.4 294.2 294 293.8 293.6 293.4 293.2
296.6 296.4 296.2 296 295.8 295.6 295.4 295.2 295 294.8 294.6 294.4 294.2 294 293.8 293.6 293.4
Fig. 17. Temperatures of the phases using the interfacial area-based model (three pictures on left hand side) and the classical model (right hand side picture). Tl − Tg
Tg − Ts dTnTs T[K]
T[K]
dTwTn
0 -0.01 -0.02 -0.03 -0.04 -0.05 -0.06 -0.07 -0.08 -0.09 -0.1 -0.11 -0.12 -0.13 -0.14 -0.15 -0.16 -0.17
0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0
Fig. 18. Temperature differences between the phases. As an alternative, a thermodynamically-based model was presented which explicitly accounts for the presence of interfaces and describes their evolution in space and time. Due to the knowledge of interfacial area, kinetic interface mass transfer can be modeled in a physically-based way. In order to decide whether kinetics of mass transfer needs to be accounted for or whether an equilibrium model would give sufficiently good results, a dimensional analysis was carried through. Also, the concept was extended to kinetic interphase heat transfer where in addition to fluid–fluid interfaces, fluid–solid interfaces are important. Two examples have illustrated the issues presented: in our results, we could observe that in the drying example, chemical non-equilibrium is significant. In the evaporator example, contrarily, thermal non-equilibrium is very pronounced. In order to advance the description of real life systems, such as those described in Sec. 1.1, an important future step would be to apply the presented model concept to practical applications and to verify the results by comparison to experimental data.
7. Acknowledgements We thank Benjamin Ahrenholz for providing the interfacial - area - capillary pressure saturation relationships from Lattice - Boltzman simulations that entered the numerical simulations shown in this chapter.
8. References Bastian, P., Birken, K., Johannsen, K., Lang, S., Eckstein, K., Neuss, N., Rentz-Reichert, H. & Wieners, C. (1997). UG - A Flexible Software Toolbox for Solving Partial Differential Equations, Computing and Visualization in Science, 1(1):27–40. Bastian, P. & Helmig, R. (1999). Efficient Fully-Coupled Solution Techniques for Two Phase Flow in Porous Media. Parallel Multigrid Solution and Large Scale Computations.,
20 20
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Advances in Water Resources 23: 199–216. Bowen, R. (1982). Compressible Porous Media Models by Use of the Theory of Mixtures, International Journal of Engineering Science 20(6): 697–735. Brusseau, M., Popovicova, J. & Silva, J. (1997). Characterizing gas–water interfacial and bulk-water partitioning for gas phase transport of organic contaminants in unsaturated porous media, Environmental Sciences Technology 31: 1645–1649. Chen, D., Pyrak-Nolte, L., Griffin, J. & Giordano, N. (2007). Measurement of interfacial area per volume for drainage and imbibition, Water Resources Research 43(12). Chen, L. & Kibbey, T. (2006). Measurement of air–water interfacial area for multiple hysteretic drainage curves in an unsaturated fine sand, Langmuir 22: 6674–6880. Culligan, K., Wildenschild, D., Christensen, B., Gray, W., Rivers, M. & Tompson, A. (2004). Interfacial area measurements for unsaturated flow through a porous medium, Water Resources Research 40: 1–12. Falta, R. W. (2000). Numerical modeling of kinetic interphase mass transfer during air sparging using a dual-media approach, Water Resources Research 36(12): 3391–3400. Falta, R. W. (2003). Modeling sub-grid-block-scale dense nonaqueous phase liquid (DNAPL) pool dissolution using a dual-domain approach, Water Resources Research 39(12). Gray, W. & Hassanizadeh, S. (1989). Averaging theorems and averaged equations for transport of interface properties in multiphase systems, International Journal of Multi-Phase Flow 15: 81–95. Gray, W. & Hassanizadeh, S. (1998). Macroscale continuum mechanics for multiphase porous-media flow including phases, interfaces, common lines, and common points, Advances in Water Resources 21: 261–281. Gray, W. & Miller, C. (2005). Thermodynamically Constrained Averaging Theory Approach for Modeling of Flow in Porous Media: 1. Motivation and Overview, Advances in Water Resources 28(2): 161–180. Hassanizadeh, S. M. & Gray, W. G. (1979). General Conservation Equations for Multi-Phase Systems: 2. Mass, Momenta, Energy, and Entropy Equations, Advances in Water Resources 2: 191–203. Hassanizadeh, S. M. & Gray, W. G. (1980). General Conservation Equations for Multi-Phase Systems: 3. Constitutive Theory for Porous Media Flow, Advances in Water Resources 3: 25–40. Hassanizadeh, S. M. & Gray, W. G. (1990). Mechanics and Thermodynamics of Multiphase Flow in Porous Media Including Interphase Boundaries, Advances in Water Resources 13(4): 169–186. Hassanizadeh, S. M. & Gray, W. G. (1993a). Thermodynamic Basis of Capillary Pressure in Porous Media, Water Resources Research 29(10): 3389 – 3405. Hassanizadeh, S. M. & Gray, W. G. (1993b). Toward an improved description of the physics of two-phase flow, Advances in Water Resources 16(1): 53–67. Held, R. & Celia, M. (2001). Modeling support of functional relationships between capillary pressure, saturation, interfacial area and common lines, Advances in Water Resources 24: 325–343. Imhoff, P., Jaffe, P. & Pinder, G. (1994). An experimental study of complete dissolution of a nonaqueous phase liquid in saturated porous media, Water Resources Research 30(2): 307–320. IPCC (2005). Carbon Dioxide Capture and Storage. Special Report of the Intergovernmental Panel on Climate Change, Cambridge University Press.
Massand andHeat HeatTransfer TransferDuring During Two-Phase Flow in Porous Media - Theory and Modeling Mass Two-Phase Flow in Porous Media - Theory and Modeling
21 21
Jackson, A., Miller, C. & Gray, W. (2009). Thermodynamically constrained averaging theory approach for modeling flow and transport phenomena in porous medium systems: 6. two-fluid-phase flow, Advances in Water Resources 32(6): 779–795. Joekar-Niasar, V., Hassanizadeh, S. M. & Leijnse, A. (2008). Insights into the relationship among capillary pressure, saturation, interfacial area and relative permeability using pore-scale network modeling, Transport in Porous Media 74: 201–219. Joekar-Niasar, V., Hassanizadeh, S. M., Pyrak-Nolte, L. J. & Berentsen, C. (2009). Simulating drainage and imbibition experiments in a high-porosity micro-model using an unstructured pore-network model, Water Resources Research 45(W02430, doi:10.1029/2007WR006641). Kalaydjian, F. (1987). A Macroscopic Description of Multiphase Flow in Porous Media Involving Spacetime Evolution of Fluid/Fluid Interface, Transport in Porous Media 2: 537 – 552. ¨ ¨ Ludecke, C. & Ludecke, D. (2000). Thermodynamik, Springer, Berlin. Marle, C.-M. (1981). From the pore scale to the macroscopic scale: Equations governing multiphase fluid flow through porous media, Proceedings of Euromech 143, pp. 57–61. Delft, Verruijt, A. and Barends, F. B. J. (eds.). Mayer, A. & Hassanizadeh, S. (2005). Soil and Groundwater Contamination: Nonaqueous Phase Liquids, American Geophysical Union. Miller, C., Poirier-McNeill, M. & Mayer, A. (1990). Dissolution of trapped nonaqueous phase liquids: Mass transfer characteristics, Water Resources Research 21(2): 77–120. Niessner, J. & Hassanizadeh, S. (2008). A Model for Two-Phase Flow in Porous Media Including Fluid–Fluid Interfacial Area, Water Resources Research . 44, W08439, doi:10.1029/2007WR006721. Niessner, J. & Hassanizadeh, S. (2009a). Modeling kinetic interphase mass transfer for two-phase flow in porous media including fluid–fluid interfacial area, Transport in Porous Media . doi:10.1007/s11242-009-9358-5. Niessner, J. & Hassanizadeh, S. (2009b). Non-equilibrium interphase heat and mass transfer during two-phase flow in porous media—theoretical considerations and modeling, Advances in Water Resources 32: 1756–1766. Porter, M., Schaap, M. & Wildenschild, D. (2009). Lattice-boltzmann simulations of the capillary pressure-saturation-interfacial area relationship for porous media, Advances in Water Resources 32(11): 1632–1640. Powers, S., Abriola, L. & Weber, W. (1992). An experimental investigation of nonaqueous phase liquid dissolution in saturated subsurface systems: steady state mass transfer rates, Water Resources Research 28: 2691–2706. Powers, S., Abriola, L. & Weber, W. (1994). An experimental investigation of nonaqueous phase liquid dissolution in saturated subsurface systems: transient mass transfer rates, Water Resources Research 30(2): 321–332. Reeves, P. & Celia, M. (1996). A functional relationship between capillary pressure, saturation, and interfacial area as revealed by a pore-scale network model, Water Resources Research 32(8): 2345–2358. Schaefer, C., DiCarlo, D. & Blunt, M. (2000). Experimental measurements of air–water interfacial area during gravity drainage and secondary imbibition in porous media, Water Resources Research 36: 885–890. van Antwerp, D., Falta, R. & Gierke, J. (2008). Numerical Simulation of Field-Scale Contaminant Mass Transfer during Air Sparging, Vadose Zone Journal 7: 294–304.
22 22
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Wildenschild, D., Hopmans, J., Vaz, C., Rivers, M. & Rikard, D. (2002). Using X-ray computed tomography in hydrology. Systems, resolutions, and limitations, Journal of Hydrology 267: 285–297. Zhang, H. & Schwartz, F. (2000). Simulating the in situ oxidative treatment of chlorinated compounds by potassium permanganate, Water Resources Research 36(10): 3031–3042.
0 2 Solute Transport With Chemical Reaction in Singleand Multi-Phase Flow in Porous Media Amgad 1 King
Salama2
M.F. El-Amin1 , and Shuyu Sun1
Abdullah University of Science and Technology (KAUST) 2 Konkuk University 1 Kingdom of Saudi Arabia 2 South Korea
1. Introduction Transport phenomena in porous media describe the motion of fluids in media of porous structure which may be accompanied by heat/mass transfer and/or chemical reactions. While transport phenomena in fluid continua have been, to a large extent, very much comprehended, the subject matters in porous media are still under careful investigation and extensive research. Several reasons may be invoked to explain the difficulties associated with the study of transport phenomena in porous media. Probably the most obvious one is the fact that fluids move in porous media in complex, tortuous, and random passages that are even unknown a priori. Consequently, the governing laws may not be solved in any sense for the apparent difficulties in defining flow boundaries. Further complexities may be added should there exists heat transfer mechanisms associated with the flow and the interactions of heat transfer between the moving fluid and the solid matrix. Moreover, chemical reactions describe essential feature of transport in porous media. It is hardly to find transport processes in porous media without chemical reaction of some sort or another. Chemical reactions in porous media can occur naturally as a result of the interactions between the moving fluid and the surface of the solid matrix. These kinds of chemical reactions, which are usually slow, are pertinent to groundwater geochemistry, or it can be made to occur by utilizing the porous media surfaces to catalyze chemical reactions between reacting fluids. The study of these complex processes in porous media necessitate complete information about the internal structure of the porous media, which is far beyond the reach of our nowadays capacities. A fundamental question, thus, arises, in what framework do we need to cast the study of transport in porous media? In other words, do we really need to get such complete, comprehensive information about a given porous medium in order to gain useful information that could help us in our engineering applications? Do we really need to know the field variables distribution at each single point in the porous medium in order to be able to predict the evolution of this system with time, for example? Is it possible to make precise measurements within the porous media for field variables? And, even if we might be able to gain such detailed information, are we going to use them in their primitive forms for further analysis and development? The answer to these kind of questions may be that, for the sake of engineering applications, we do not need such a complete, comprehensive details, neither will we be able to obtain them nor will they
2 24
Transfer Mass Transfer in Multiphase Systems andMass its Applications
be useful in their primitive form. In other words, field variables distribution will be randomly distributed and we would, in general, need to average them in order to gain statistically useful integral information. These ideas, in fact, enriched researchers’ minds on their search for an appropriate framework to study phenomena in porous media. That is, if we need to average the pointwise field variables to get useful information, should not we might, as well, look for doing such kind of averaging on our way to investigating porous media. That is, is it possible to upscale our view to porous media such that we get smooth variables that represent integral information about the behavior of field variables not at a single point but within a volume of the porous medium surrounding this point? It turns out that researchers have appealed to this strategy several times on their way to explore the behavior of systems composed of innumerable building blocks. Thermodynamics, solid mechanics, fluid mechanics etc. are examples of sciences that adopted this approach by assuming the medium as continuum. Now, is it feasible to, also, treat phenomena occurring in porous media as continua? The answer to this question turns out to be yes as will be explained in the next section.
2. Framework Salama & van Geel (2008a) provided an interesting analogy that sheds light on the possibility to adopt the continuum approach to phenomena occurring in porous media. They stated that an observer closer to a given porous medium will be able to see details of the porous medium (at least at the surface) that an observer from far distant would, generally, ignore. To the distant observer, the medium looks smooth and homogeneous like a continuum, Fig.1. It is exactly this point of view that we seek and it remains interesting to estimate that minimum distance that our observer would have to stay to get the continuum feeling of the medium. Of course moving beyond this distance would result in no significant improvement in the continuum picture. However, moving too far without having established the continuum feeling such that the extents of the domain enter the scene implies that it would not be possible to establish the continuum picture. This analogy, in fact, gives us an idea on how to properly define upscaling to porous media and hence establish continua. That is we need an upscaling scale (volume) that is much larger than small scale heterogeneity (e.g., pore diameter) and small enough such that it does not encompass the domain boundaries. The mathematical machinery that provide such an upscaled description to phenomena occurring in porous media includes theory of mixtures, the method of volume averaging, method of homogenization, etc. In the framework of theory of mixtures, global balance equations are written based on the assumption of the existence of macroscale field variables, which are employed in the global balance equations. A localized version of these equations may then be obtained through mathematical manipulations to get what is called the macroscopic point equations. In the frame work of the method of volume averaging, on the other hand, the microscale conservation laws adapted to fluid continua filling the interstitial space are subjected to some integral operators over representative volume which size is understood within certain set of length scale constraints. These length scale constraints were introduced for proper upscaling based on the pioneering work of several researchers including (Whitaker, Gray, Hassanizadeh, Bear, Bachmat, Quintard, Slattery, Cushman, Marle and many others). Recently, (Salama & van Geel, 2008a) have postulated the conditions required for proper upscaling such that one may get the correct set of equations subject to the constraints pertinent to adhering to these conditions, as will be explained later. This set of macroscopic point equations, in which macroscopic field variables are defined at yet a larger scale than their microscopic counterpart, represents the governing conservation laws at the
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
3 25
new macroscale. In this chapter we will be concerned mainly with the method of volume averaging.
3. Requirements for proper averaging The upscaling process implies a one to one mapping between two domains one of which represents the actual porous medium and the second represents a fictitious continuous domain. Any point in the actual porous medium domain may lay on either the solid phase or the fluid phase and thus one can define a phase function which equals one if the point is in the fluid phase and is zero if it lays elsewhere. Over the actual porous medium domain, field variables are defined only over fluid phases (i.e., they only have values in the corresponding fluid-phase and zero elsewhere). These variables and/or their derivatives may not be continuous, particularly at the interfaces. The corresponding point over the fictitious medium, on the other hand, lays over a continuum where it is immaterial to talk about particular phase. Moreover, the macroscopic field variables defined over the fictitious medium are continuous over the whole domain, except possibly at the external boundaries. These macroscopic field variables represent the behavior of the fluid continuum contained within a certain volume (called representative elementary volume, REV) and are assigned to a single point in the fictitious domain. In order to succeed in establishing correctly this mapping process, extensive amount of research work have been conducted since the second half of the last century by several research groups including the pioneers mentioned earlier. On reviewing this work, (?) and recently Salama & van Geel (2008a) proposed a set of requirements such that proper upscaling may be achieved. They require that, 1. The smoothed macroscopic variables are free from pore-related heterogeneity. 2. The smoothed macroscopic variables do not depend on the size of the averaging volume.
ĨƌŽŵĐůŽƐĞƌƉƌŽdžŝŵŝƚLJ
ĨƌŽŵĨĂƌĚŝƐƚĂŶƚ
Fig. 1. View of two different observers at different proximity from a given porous medium domain.
4 26
Transfer Mass Transfer in Multiphase Systems andMass its Applications
3. The extent of the domain under study is large enough compared with the size of the averaging volume. 4. The amount of any conservative quantity (mass, momentum, energy, etc.) within any given volume (of the size of the REV or larger) is the same if evaluated over the actual porous medium domain or the corresponding fictitious domain. And, similarly, the flux of any conservative quantity across any surface (of the size of REA or larger) is also the same in both the actual and the fictitious domains. These requirements necessitate the followings: – An averaging volume exists for every macroscopic field variable. – A common range of averaging volume may be found for all the field variables. Adhering to the first three requirements, (Whitaker, 1967) indicated that if β represents a length scale pertinent to the internal microscopic structure of the porous medium (typical pore or grain diameter) and if L represents a length scale associated with the extent of the domain of interest, then the length scale of the averaging volume should be such that it satisfies the following constraints I. >> β II. << L Adhering to the fourth requirement, on the other hand, Salama & van Geel (2008a) were able to establish the proper averaging operator. They indicated that if we consider any conservative, intensive quantity, ψβ , which may be scalar (e.g., mass of certain species per unit volume, energy per unit mass, etc.), or vector (e.g., linear momentum per unit mass). The total amount of ψβ should equal to that evaluated over the same volume in the fictitious porous medium, Fig.2, which may be evaluated as: ψtotal =
REV
ρ β (r, t)ψβ (r, t)γβ (r)dv
(1)
where ρ β is the density of the β-phase, ψβ is an intensive quantity, γβ is the phase function, and r represents the position vector spanning the REV. The time, t, in the argument of the indicator function, γβ represents the scenario of moving interfaces (e.g. immiscible multiphase system). In our case, however, the time may be omitted due to the fact that for our solid-fluid systems, the interface boundaries are assumed fixed in space. Refer to Fig.2 for a geometrical illustration. The total amount of ψβ should equal to that evaluated over the same volume in the fictitious porous medium, Fig.3, which may be evaluated as: ψtotal =
β
β
REV
ρβ
β
β (r, t) ψβ (r, t) β (r)dv
(2)
where ρ β and ψβ represent the intrinsic phase average of the β-phase density and intensive quantity as described earlier in Eq. (2), and β is the porosity function over the REV. That is, REV
ρ β (r, t)ψβ (r, t)γβ (r, t)dv =
REV
ρβ
β
β (r, t) ψβ (r, t) β (r)dv
(3)
From the condition that the averaged quantities are assigned to the centroid of the averaging volume, (Salama & van Geel, 2008a) postulated that,
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
5 27
r x O Fig. 2. An REV.
= β (x, t)v = REV β (r, t)dv β β β ii. REV ρ β (r, t)γβ (r)dv = ρ β (x, t) ψβ (x, t)v = REV ρ β (r, t) β (r, t)dv β β iii. REV ρ β (r, t)ψβ (r, t)γβ (r)dv = ρ β (x, t) ψβ (x, t) β (x, t)v = β β (r, t) ψβ (r, t) β (r, t)dv REV ρ β i.
REV γ β (r, t ) dv
β β where ρ β (x, t) ψβ (x, t) and β (x) are the intrinsic-phase average of ρ β , ψβ and the porosity at the centroid of the REV, respectively (Fig. 2). This indicates that sampling the same volume (REV) in both the actual porous medium and the fictitious one should yield the same conservative quantity. In fact this equation may be taken as the definition for the averaging processes. That is,
ψβ
β
(x, t) =
$Q5(9RYHUWKHDFWXDOSRURXVPHGLXP
ρβ
1 β
β v
v
ρ β (r, t)ψβ (r, t)γβ (r)dv
7KHVDPHYROXPHRYHUWKHILFWLWLRXVRQH
Fig. 3. An REV over the actual porous region and an equivalent volume over the fictitious one.
(4)
6 28
Transfer Mass Transfer in Multiphase Systems andMass its Applications
which was introduced by (Hassanizadeh & Gray, 1979b;a; 1980) and was called the mass β = ρ β and average of ψβ . In situations where β-phase is incompressible, we have ρ β the above equation reduces to Eq. (2) and also, if ψβ represents a per unit volume quantity, for example the concentration of the β-phase, the density may be omitted. In other words the above mentioned three postulates may be used to define the averaging operators. β Moreover, these postulates also suggest that: ψβ = ψβ which will show to simplify mathematical manipulation. Now for incompressible fluids Eq. (7) implies that the product β ψβ (r, t) β (r) changes linearly over the REV. (Salama & van Geel, 2008a) further indicated β that, there are at least three possibilities for the product ψβ (r, t) β (r) to change linearly within the REV: 1. both ψ β and β remain constant within the REV. 2. ψ β changes linearly and β remains constant. 3. ψ β remains constant and β changes linearly. These requirements are rather restrictive, that is, if we allow ψ β and β to vary within the averaging volume such that their product, which is apparently nonlinear, they required that the nonlinearity within the averaging volume is relatively small. They defined the criteria for this case as: if represents the length scale over which significant variation in porosity occur within the REV and ψ represents that length scale over which significant deviation from the β straight line variation of the intrinsic phase average of the conservative quantity ψβ may occur, then they introduced their celebrated inequality III. << min( , ψ ) Now adhering to these length scale constraints, it may be possible, in principle, to establish the continuum view to transport phenomena in porous media.
4. Consequences As with our experience upon adopting the continuum hypothesis to the science of fluid mechanics, rather than the primitive Newtonian mechanics at the molecular scale an apparently different formulation needed to be adopted and several things arise. Probably the most obvious one is the fact that the state variables are modified. That is velocity vectors, for example, are, now, no longer associated with particles, rather they represent an integral behavior of a collection of several many particles contained within an averaging volume. The fluctuations of the actual particles velocity around continuum velocity suggest that two different mechanisms for heat and momentum transfer be hypothesized. One is associated with the transport of momentum and energy along with the continuum velocity and the other associated with the fluctuating components that appear as a surface flux in the continuum conservation laws, (Leal, 2007). We expect that these mechanisms become even more pronounced when adopting the continuum hypothesis to porous media. As an example, the dispersion of passive solute in pure liquids is very much influenced by the diffusion coefficient which is a macroscopic property of the medium. In porous media, on the other hand, dispersion becomes more pronounced and is no longer a property of the
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
7 29
different fluids; it also depends on the internal geometrical structure of the porous medium. A second consequence of the continuum hypothesis is an uncertainty in the boundary conditions to be used in conjunction with the resulting macroscopic equations for motion and heat and mass transfer (Salama & van Geel, 2008b). A third consequence is the fact that the derived macroscopic point equations contain terms at the lower scale. These terms makes the macroscopic equations unclosed. Therefore, they need to be represented in terms of macroscopic field variables though parameters that me be identified and measured.
5. Single-phase flow modeling 5.1 Conservation laws
Following the constraints introduced earlier to properly upscale equations of motion of fluid continuum to be adapted to the upscaled continuum of porous medium, researchers and scientists were able to suggest the governing laws at the new continuum. They may be written for incompressible fluids as: Continuity
Momentum
∇ · vβ = 0 β β β + ρ β vβ · ∇ vβ = −∇ p β + ρ β g+ β μ ρ β Fβ μ β ∇2 vβ − Kβ vβ − √ vβ vβ ρβ
∂ v β ∂t
(5)
(6)
K
Energy σ
β ∂ Tβ
β β + vβ · ∇ Tβ = k∇2 Tβ ± Q
(7)
β β + vβ · ∇ c β = ∇ · D · ∇ c β ±S
(8)
∂t
Solute transport
β ∂ cβ ∂t
β β where vβ and p β epresent the intrinsic average velocity and pressure, respectively and √ vβ is the superficial average velocity, v = u2 + v2 , σ = (ρC p ) M /(ρC p ) f , k = (k M /(ρC p ) f , is the thermal diffusivity. From now on we will drop the averaging operator, , to simplify notations. The energy equation is written assuming thermal equilibrium between the solid matrix and the moving fluid. The generic terms, Q and S, in the energy and solute equations represent energy added or taken from the system per unit volume of the fluid per unit time and the mass of solute added or depleted per unit volume of the fluid per unit time due to some source (e.g., chemical reaction which depends on the chemistry, the surface properties of the fluid/solid interfaces, etc.). Dissolution of the solid phase, for example, adds solute to the fluid and hence S > 0, while precipitation depletes it, i.e., S < 0. Organic decomposition or oxidation or reduction reactions may provide both sources and sinks. Chemical reactions in porous media are usually complex that even in apparently simple processes (e.g., dissolution), sequence of steps are usually involved. This implies that the time scale of the slowest step essentially determines the time required to progress through the sequence of steps. Among
8 30
Transfer Mass Transfer in Multiphase Systems andMass its Applications
the different internal steps, it seems that the rate-limiting step is determined by reaction kinetics. Therefore, the chemical reaction source term in the solute transport equation may be represented in terms of rate constant, k, which lumps several factors multiplied by the concentration, i.e., S = k f (s)
(9)
time−1
and the form of the function f may be determined where k has dimension experimentally, (e.g., in the form of a power law). Apparently, the above set of equations is nonlinear and hence requires, generally, numerical techniques to provide solution (finite difference, finite element, boundary element, etc.). However, in some simplified situations, one may find similarity transformations to transform the governing set of partial differential equations to a set of ordinary differential equations which greatly simplify solutions. As an example, in the following subsection we show the results of using such similarity transformations in investigating the problem of natural convection and double dispersion past a vertical flat plate immersed in a homogeneous porous medium in connection with boundary layer approximation. 5.2 Examble: Chemical reaction in natural convection
The present investigation describes the combined effect of chemical reaction, solutal, and thermal dispersions on non-Darcian natural convection heat and mass transfer over a vertical flat plate in a fluid saturated porous medium (El-Amin et al., 2008). It can be described as follows: A fluid saturating a porous medium is induced to flow steadily by the action of buoyancy forces originated by the combined effect of both heat and solute concentration on the density of the saturating fluid. A heated, impermeable, semi-infinite vertical wall with both temperature and concentration kept constant is immersed in the porous medium. As heat and species disperse across the fluid, its density changes in space and time and the fluid is induced to flow in the upward direction adjacent to the vertical plate. Steady state is reached when both temperature and concentration profiles no longer change with time. In this study, the inclusion of an n-order chemical reaction is considered in the solute transport equation. On the other hand, the non-Darcy (Forchheimer) term is assumed in the flow equations. This term accounts for the non-linear effect of pore resistance and was first introduced by Forchheimer. It incorporates an additional empirical (dimensionless) constant, which is a property of the solid matrix, (Herwig & Koch, 1991). Thermal and mass diffusivities are defined in terms of the molecular thermal and solutal diffusivities, respectively. The Darcy and non-Darcy flow, temperature and concentration fields in porous media are observed to be governed by complex interactions among the diffusion and convection mechanisms as will be discussed later. It is assumed that the medium is isotropic with neither radiative heat transfer nor viscous dissipation effects. Moreover, thermal local equilibrium is also assumed. Physical model and coordinate system is shown in Fig.4. The x-axis is taken along the plate and the y-axis is normal to it. The wall is maintained at constant temperature and concentration, Tw and Cw , respectively. The governing equations for the steady state scenario [as given by (Mulolani & Rahman, 2000; El-Amin, 2004) may be presented as: Continuity:
∂u ∂v + =0 ∂x ∂y
(10)
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
9 31
Fig. 4. Physical model and coordinate system. Momentum: u
Energy: u
√ K ∂p c K + ρg u |v| = − ν μ ∂x √ c K K ∂p v v |v| = − ν μ ∂y
∂T ∂T ∂ +v = ∂x ∂y ∂x
αx
∂T ∂x
+
∂ ∂y
+
∂ ∂y
Dy
∂C ∂y
αy
(11) (12) ∂T ∂y
(13)
Solute transport: u Density
∂C ∂C ∂ +v = ∂x ∂y ∂x
Dx
∂C ∂x
− K0 (C − C∞ )n
ρ = ρ∞ [1 − β∗ ( T − T∞ ) − β∗∗ (C − C∞ )]
(14)
(15)
Along with the boundary conditions: y = 0 : v = 0, Tw = const., Cw = const.; y → ∞ : u = 0, T → T∞ , C → C∞
(16)
where β∗ is the thermal expansion coefficient β∗∗ is the solutal expansion coefficient. It should be noted that u and v refers to components of the volume averaged (superficial) velocity of the fluid. The chemical reaction effect is acted by the last term in the right hand side of Eq. (14), where, the power n is the order of reaction and K0 is the chemical reaction constant. It is assumed that the normal component of the velocity near the boundary is small compared
10 32
Transfer Mass Transfer in Multiphase Systems andMass its Applications
with the other component of the velocity and the derivatives of any quantity in the normal direction are large compared with derivatives of the quantity in direction of the wall. Under these assumptions, Eq. (10) remains the same, while Eqs. (11)- (15) become: √ c K 2 K ∂p u+ u =− + ρg (17) ν μ ∂x ∂p =0 ∂y
∂T ∂T ∂ ∂T +v = αy ∂x ∂y ∂y ∂y ∂C ∂C ∂ ∂C u +v = − K0 (C − C∞ )n Dy ∂x ∂y ∂y ∂y u
(18) (19) (20)
Following (Telles & V.Trevisan, 1993), the quantities of αy and Dy are variables defined as αy = α + γd |v| and Dy = D + ζd |v| where, α and D are the molecular thermal and solutal diffusivities, respectively, whereas γd |v| and ζd |v| represent dispersion thermal and solutal diffusivities, respectively. This model for thermal dispersion has been used extensively (e.g., (Cheng, 1981; Plumb, 1983; Hong & Tien, 1987; Lai & Kulacki, 1989; Murthy & Singh, 1997) in studies of non-Darcy convective heat transfer in porous media. Invoking the Boussinesq approximations, and defining the velocity components u and v in terms of stream function ψ as: u = ∂ψ/∂y and v = −∂ψ/∂x, the pressure term may be eliminated between Eqs. (17) and (18) and one obtains: √ ∂2 ψ Kgβ∗ ∂T c K ∂ ∂ψ 2 Kgβ∗∗ ∂C + = + (21) ρ∞ ν ∂y ∂y μ ∂y μ ∂y ∂y2
∂ψ ∂T ∂ψ ∂T ∂ ∂ψ ∂T − = α + γd (22) ∂y ∂x ∂x ∂y ∂y ∂y ∂y
∂ψ ∂C ∂ψ ∂C ∂ ∂ψ ∂C − = − K0 (C − C∞ )n (23) D + ζd ∂y ∂x ∂x ∂y ∂y ∂y ∂y Introducing the similarity variable and similarity profiles (El-Amin, 2004): y ψ T − T∞ C − C∞ , θ (η ) = , φ(η ) = η = Ra1/2 , f (η ) = x x T − T C w ∞ w − C∞ αRa1/2 x The problem statement is reduced to: f + 2F0 Rad f f = θ + Nφ θ +
1 f θ + γRad f θ + f θ = 0 2
(24)
(25) (26)
Gc 1 (27) Le f φ + ζ LeRad f φ + f φ − Scλ 2 φn=0 2 Re x √ As mentioned in (El-Amin, 2004), the parameter F0 = c Kα/νd collects a set of parameters that depend on the structure of the porous medium and the thermo physical properties of the fluid saturating it, Rad = Kgβ∗ ( Tw − T∞ )d/αν is the modified, pore-diameter-dependent φ +
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
11 33
Rayleigh number, and N = β∗∗ (Cw − C∞ )/β∗ ν is the buoyancy ratio parameter. With analogy to (Mulolani & Rahman, 2000; Aissa & Mohammadein, 2006), we define Gc to be the modified Grashof number, Re x is local Reynolds number, Sc and λ are Schmidt number and non-dimensional chemical reaction parameter defined as Gc = β∗∗ g(Cw − C∞ )2 x3 /ν2 , Re x = ur x/ν, Sc = ν/D and λ = K0 αd(Cw − C∞ )n−3 /Kgβ∗∗ , where the diffusivity
ratio Le (Lewis number) is the ratio of Schmidt number and Prandtl number, and ur = gβ∗ d( Tw − T∞ ) is the reference velocity as defined by (Elbashbeshy, 1997). Eq. (27) can be rewritten in the following form: 1 (28) Le f φ + ζ LeRad f φ + f φ − χφn = 0 2 With analogy to (Prasad et al., 2003; Aissa & Mohammadein, 2006), the non-dimensional chemical reaction parameter χ is defined as χ = ScλGc/Re2x . The boundary conditions then become: φ +
f (0) = 0, θ (0) = φ(0) = 1, f (∞) = θ (∞) = φ(∞) = 0
(29)
It is noteworthy to state that F0 = 0 corresponds to the Darcian free convection regime, γ = 0 represents the case where the thermal dispersion effect is neglected and ζ = 0 represents the case where the solutal dispersion effect is neglected. In Eq. (16), N > 0 indicates the aiding buoyancy and N < 0 indicates the opposing buoyancy. On the other hand, from the definition of the stream function, the velocity components become u = (αRa x /x ) f and v = −(αRa1/2 x /2x )[ f − η f ]. The local heat transfer rate which is one of the primary interest of the study is given by qw = −k e (∂T/∂y)|y=0 , where, k e = k + k d is the effective thermal conductivity of the porous medium which is the sum of the molecular thermal conductivity k and the dispersion thermal conductivity k d . The local Nusselt number Nu x is defined as Nu x = qw x/( Tw − T∞ )k e . Now the set of primary variables which describes the problem may be replaced with another set of dimensionless variables. This include: a dimension less variable that is related to the process of heat transfer in the given system which may √ be expressed as Nu x / Ra x = −[1 + γRad F (0)]θ (0). Also, the local mass flux at the vertical wall that is given by jw = − Dy (∂C/∂y)|y=0 defines another dimensionless variable that is the local Sherwood number is given by, Sh x = jw√ x/(Cw − C∞ ) D. This, analogously, may also define another dimensionless variable as Sh x / Ra x = −[1 + ζRad F (0)]φ (0). The details of the effects of all these parameters are presented in (El-Amin et al., 2008). We, however, highlight the role of the chemical reaction on this system. The effect of chemical reaction parameter χ on the concentration as a function of the boundary layer thickness η and with respect to the following parameters: Le = 0.5, F0 = 0.3, Rad = 0.7, γ = ζ = 0.0, N = −0.1 are plotted in Fig.5. This figure indicates that increasing the chemical reaction parameter decreases the concentration distributions, for this particular system. That is, chemical reaction in this system results in the consumption of the chemical of interest and hence results in concentration profile to decrease. Moreover, this particular system also shows the increase in chemical reaction parameter χ to enhance mass transfer rates (defined in terms of Sherwood number) as shown in Fig.6. It is worth mentioning that the effects of chemical reaction on velocity and temperature profiles as well as heat transfer rate may be negligible. Figs. 7 and 8 illustrate, respectively, the effect of Lewis number Le on Nusselt number and Sherwood number for various with the following parameters set as χ = 0.02, Rad = 0.7, F0 = 0.3, N = −0.1, γ = 0.0. The parameter ζ seems to reduce the heat transfer rates especially with higher Le number as shown in Fig. 7. In the case of mass transfer rates
12 34
Transfer Mass Transfer in Multiphase Systems andMass its Applications
1.0 F
0.8
F F
I
0.6 0.4 0.2 0.0 0.0
0.5
1.0
1.5
2.0 K
2.5
3.0
3.5
4.0
Fig. 5. Variation of dimensionless concentration with similarity space variable η for different χ (Le = 0.5, F0 = 0.3, Rad = 0.7, γ = ζ = 0.0, N = −0.1). (defined in terms of Sherwood number), Fig. 8 illustrates that the parameter ζ enhances the 1.55 and the opposite is true for high values of mass transfer rate with small values of Le< 1.55. This may be explained as follows: for small values of Le number, which indicates Le>
1.0
Shx/(Rax^0.5)
0.8 0.6 F F F F F
0.4
0.2 0.0
0.5
1.0
1.5
2.0 Le
2.5
3.0
3.5
4.0
Fig. 6. Effect of Lewis number on Sherwood number for various χ (F0 = 0.3, Rad = 0.7, γ = ζ = 0.0, N = −0.1).
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
13 35
Nux/(Rax^0.5)
0.436 ] ] ] ]
0.434
0.431 0.429 0.426 0.0
0.5
1.0
1.5
2.0 Le
2.5
3.0
3.5
4.0
Fig. 7. Variation of Nusselt number with Lewis number for various ζ (χ = 0.02, F0 = 0.3, Rad = 0.7, γ = 0.0, N = −0.1). that mass dispersion outweighs heat dispersion, the increase in the parameter ζ causes mass dispersion mechanism to be higher and since the concentration at the wall is kept constant this increases concentration gradient near the wall and hence increases Sherwood number. As
1.0 ] ] ] ]
Shx/(Rax^0.5)
0.8
0.6 0.4 0.2 0.0
0.5
1.0
1.5
2.0 Le
2.5
3.0
3.5
4.0
Fig. 8. Effect of Lewis number on Sherwood number for various ζ (χ = 0.02, F0 = 0.3, Rad = 0.7, γ = 0.0, N = −0.1).
14 36
Transfer Mass Transfer in Multiphase Systems andMass its Applications
0.58
Nux/(Rax^0.5)
0.54
J J J J
0.50
0.46 0.42 0.0
0.5
1.0
1.5
2.0 Le
2.5
3.0
3.5
4.0
Fig. 9. Variation of Nusselt number with Lewis number for various γ (χ = 0.02, F0 = 0.3, Rad = 0.7, ζ = 0.0, N = −0.1). Le increases (Le > 1), heat dispersion outweighs mass dispersion and with the increase in ζ concentration gradient near the wall becomes smaller and this results in decreasing Sherwood number. Fig. 9 indicates that the increase in thermal dispersion parameter enhances the heat transfer rates.
6. Multi-phase flow modeling Multi-phase systems in porous media are ubiquitous either naturally in connection with, for example, vadose zone hydrology, which involves the complex interaction between three phases (air, groundwater and soil) and also in many industrial applications such as enhanced oil recovery (e.g., chemical flooding and CO2 injection), Nuclear waste disposal, transport of groundwater contaminated with hydrocarbon (NAPL, DNAPL), etc. Modeling of Multi-phase flows in porous media is, obviously, more difficult than in single-phase systems. Here we have to account for the complex interfacial interactions between phases as well as the time dependent deformation they undergo. Modeling of compositional flows in porous media is, therefore, necessary to understand a number of problems related to the environment (e.g., CO2 sequestration) and industry (e.g., enhanced oil recovery). For example, CO2 injection in hydrocarbon reservoirs has a double benefit, on the one side it is a profitable method due to issues related to global warming, and on the other hand it represents an effective mechanism in hydrocarbon recovery. Modeling of these processes is difficult because the several mechanisms involved. For example, this injection methodology associates, in addition to species transfer between phases, some substantial changes in density and viscosity of the phases. The number of phases and compositions of each phase depend on the thermodynamic conditions and the concentration of each species. Also, multi-phase compositional flows have varies applications in different areas such as nuclear reactor safety analysis (Dhir, 1994),
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
15 37
high-level radioactive waste repositories (Doughty & Pruess, 1988), drying of porous solids and soils (Whitaker, 1977), porous heat pipes (Udell, 1985), geothermal energy production (Cheng, 1978), etc. The mathematical formulation of the transport phenomena are governed by conservation principles for each phase separately and by appropriate interfacial conditions between various phases. Firstly we give the general governing equations of multi-phase, multicomponent transport in porous media. Then, we provide them in details with analysis for two- and three-phase flows. The incompressible multi-phase compositional flow of immiscible fluids are described by the mass conservation in a phase (continuity equation), momentum conservation in a phase (generalized Darcy’s equation) and mass conservation of component in phase (spices transport equation). The transport of N-components of multi-phase flow in porous media are described by the molar balance equations. Mass conservation in phase α : ∂(φρα Sα ) = −∇ · (ρα uα ) + qα ∂t Momentum conservation in phase α: uα = −
(30)
Kkrα (∇ pα + ρα g∇z) μα
(31)
Energy conservation in phase α: ∂ (ρα Sα hα ) + ∇ · (ρα uα hα ) = ∇ · (Sα k α ∇ T ) + q¯α ∂t Mass conservation of component i in phase α: ∂(φczi ) + ∇ · ∑ cα xαi uα = ∇ · φDαi ∇(czi ) + Fi , ∂t α
i = 1, · · · , N
(32)
(33)
where the index α denotes to the phase. S, p, q, u, kr , ρ and μ are the phase saturation, pressure, mass flow rate, Darcy velocity, relative permeability, density and viscosity, respectively. c is the overall molar density; zi is the total mole fraction of ith component; cα is the phase molar densities; xαi is the phase molar fractions; and Fi is the source/sink term of the ith component which can be considered as the phase change at the interface between the phase α and other phases; and/or the rate of interface transfer of the component i caused by chemical reaction (chemical non-equilibrium). Dαi is a macroscopic second-order tensor incorporating diffusive and dispersive effects. The local thermal equilibrium among phases has been assumed, (Tα = T, ∀α), and k α and q¯α represent the effective thermal conductivity of the phase α and the interphase heat transfer rate associated with phase α, respectively. Hence, ∑α q¯α = q, q is an external volumetric heat source/sink (Starikovicius, 2003). The phase enthalpy k α is related T to the temperature T by, hα = 0 c pα dT + h0α . The saturation Sα of the phases are constrained by, c pα and h0α are the specific heat and the reference enthalpy oh phase α, respectively.
∑ Sα = 1 α
(34)
One may defined the phase saturation as the fraction of the void volume of a porous medium filled by this fluid phase. The mass flow rate qα , describe sources or sinks and can be defined by the following relation (Chen, 2007),
16 38
Transfer Mass Transfer in Multiphase Systems andMass its Applications
q = ∑ ρ j q j δ( x − x j )
(35)
q = − ∑ ρ j q j δ( x − x j )
(36)
j
j
The index j represents the points of sources or sinks. Eq. (35) represents sources and q j represents volume of the fluid (with density ρ j ) injected per unit time at the points locations x j , while, Eq. (36) represents sinks and q j represents volume of the fluid produced per unit time at x j . On the other hand, the molar density of wetting and nonwetting phases is given by, N
∑ cαi
cα =
(37)
i =1
where cαi is the molar densities of the component i in the phase α. Therefore, the mole fraction of the component i in the respective phase is given as, xαi =
cαi , cα
i = 1, · · · , N
(38)
The mole fraction balance implies that, N
∑ xαi = 1
(39)
i =1
Also, for the total mole fraction of ith component, N
∑ zi = 1
(40)
i =1
Alternatively, Eq. (32) can be rewritten in the following form, ∂ φ ∑ cα xαi Sα + ∇ · ∑ cα xαi uα = ∇ · φcα Sα Dαi ∇ xαi + Fi , ∂t α α
i = 1, · · · , N
(41)
Fi may be written as, Fi = ∑ xαi qα , α
i = 1, · · · , N
(42)
where qα is the phase flow rate given by Eqs. (35), (36). From Eqs. (32) and (41), one may deduce, czi = ∑ cα xαi Sα = ∑ cαi Sα , α
α
i = 1, · · · , N
(43)
If one uses the total mass variable X of the system (Nolen 1973; Young and Stephenson 1983), X = ∑ c α Sα α
Therefore,
(44)
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
1=∑ α
c α Sα = ∑ Cα X α
17 39
(45)
where Cα is the mass fraction phase α, respectively. The quantity, k α = Kkrα
(46)
is known as effective permeability of the phase α. The relative permeability of a phase is a dimensionless measure of the effective permeability of that phase. It is the ratio of the effective permeability of that phase to the absolute permeability. Also, it is interesting to define the quantities mα which is known as mobility ratios of phases α, respectively are given by, mα =
kα μα
(47)
The capillary pressure is the the difference between the pressures for two adjacent phases α1 and α2 , given as, pcα1 α2 = pα1 − pα2
(48)
The capillary pressure function is dependent on the pore geometry, fluid physical properties and phase saturations. The two phase capillary pressure can be expressed by Leverett dimensionless function J (S), which is a function of the normalized saturation S, pc = γ
φ K
1 2
J (S)
(49)
The J (S) function typically lies between two limiting (drainage and imbibition) curves which can be obtained experimentally. 6.1 Two-phase compositional flow
The governing equations of two-phase compositional flow of immiscible fluids are given by, Mass conservation in phase α: ∂(φρα Sα ) = −∇ · (ρα uα ) + qα ∂t Momentum conservation in phase α: uα = −
Kkrα (∇ pα + ρα g∇z) μα
α = w, n
(50)
α = w, n
(51)
Mass conservation of component i in phase α: ∂(φczi ) + ∇ · (cw xwi uw + cn xni un ) = Fi , i = 1, · · · , N (52) ∂t where the index α denotes to the wetting (w) and non-wetting (n), respectively. S, p, q, u, kr , ρ and μ are the phase saturation, pressure, mass flow rate, Darcy velocity, relative permeability, density and viscosity, respectively. c is the overall molar density; zi is the total mole fraction of ith component; cw , cn are the wetting- and nonwetting-phase molar densities; xwi , xni are the wetting- and nonwetting-phase molar fractions; and Fi is the source/sink term of the ith component. The saturation Sα of the phases are constrained by,
18 40
Transfer Mass Transfer in Multiphase Systems andMass its Applications
(a) Corey approximation
(b) LET approximation
Fig. 10. Relative permeabilities. Sw + Sn = 1
(53)
The normalized wetting phase saturation S is given by, Sw − S0w 0≤S≤1 (54) 1 − Snr − S0w where S0w is the irreducible (minimal) wetting phase saturation and Snr is the residual (minimal) non-wetting phase saturation. The expression of relation between the relative permeabilities and the normalized wetting phase saturation S, given as, S=
krw = k0rw S a
(55)
krn = k0rn (1 − S)b
(56)
The empirical parameters a and b can be obtained from measured data either by optimizing to analytical interpretation of measured data, or by optimizing using a core flow numerical simulator to match the experiment. k0rw = krw (S = 1) is the endpoint relative permeability to water, and k0rn = krn (S = 0) is the endpoint relative permeability to the non-wetting phase. For example, for the Corey power-law correlation, a = b = 2, k0rn = 1, k0rw = 0.6, for water-oil system see Fig.10a. Another example of relative permeabilities correlations is LET model which is more accurate than Corey model. The LET-type approximation is described by three empirical parameters L,E and T. The relative permeability correlation for water-oil system has the form, krw =
S Lw
k0rw S Lw + Ew (1 − S) Tw
(57)
and
(1 − S ) L n (58) (1 − S) Ln + En S Tn The parameter E describes the position of the slope (or the elevation) of the curve. Fig. 10b shows LET relative permeabilities with L = E = T = 2 and k0rw = 0.6 for water-oil system. krn =
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
19 41
Fig. 11. Capillary pressure as a function of normalized wetting phase saturation. Also, there are Corey- and LET-correlations for gas-water and gas-oil systems similar to the oil-water system. Correlation of the imbibition capillary pressure data depends on the type of application. For example, for water-oil system, see for example, (Pooladi-Darvish & Firoozabadi, 2000), the capillary pressure and the normalized wetting phase saturation are correlated as, pc = − B ln S
(59) 1 φ
2
where B is the capillary pressure parameter, which is equivalent to γ K , in the general 1 φ 2 form of the capillary pressure, Eq. (49), thus, B ≡ −γ K and J (S) ≡ ln S. Note that J (S) is a scalar non-negative function. Capillary pressure as a function of normalized wetting phase (e.g. water) saturation is shown in Fig. 11. Also, the well known (van Genuchten, 1980; Brooks & Corey, 1964) capillary pressure formulae which can be written as, pc = p0 (S−1/m − 1)1−m , pc = pd S−1/λ ,
0<m<1
0.2 < λ < 3
(60) (61)
where p0 is characteristic capillary pressure and pd is called entry pressure. The capillary pressure pc is defined as a difference between the non-wetting and wetting phase pressures, pc = pn − pw the total velocity defined as,
(62)
20 42
Transfer Mass Transfer in Multiphase Systems andMass its Applications
u = uw + un
(63)
m(S) = mw (S) + mn (S)
(64)
the total mobility is given by,
the fractional flow functions are, f w (S) =
mw (S) , m(S)
f n (S) =
mn (S) m(S)
(65)
and the density difference is, Δρ = ρn − ρw
(66)
On the other hand, the molar density of wetting and nonwetting phases is given by, cw =
N
∑ cwi ,
i =1
cn =
N
∑ cni
(67)
i =1
where cwi and cni are the molar densities of component i in the wetting phase and nonwetting phase phases, respectively. Therefore, the mole fraction of component i in the respective phase is given as, cwi , cw The mole fraction balance implies that, xwi =
xni =
cni , cn
N
N
i =1
i =1
i = 1, · · · , N
(68)
∑ xwi = 1, ∑ xni = 1
(69)
Also, for the total mole fraction of ith component, N
∑ zi = 1
(70)
i =1
Alternatively, Eq. (52) can be rewritten in the following form, ∂ [φ (cw xwi Sw + cn xni Sn )] + ∇ · (cw xwi uw + cn xni un ) = Fi , ∂t Fi may be written as, Fi = xwi qw + xni qn ,
i = 1, · · · , N
i = 1, · · · , N
(71)
(72)
where qw and qn are wetting phase and nonwetting phase phase flow rate, respectively. From Eqs. (32) and (72), one may deduce, czi = cw xwi Sw + cn xni Sn = cwi Sw + cni Sn ,
i = 1, · · · , N
(73)
If one uses the total mass variable X of the system (Nolen, 1973; Young & Stephenson, 1983), X = c w Sw + c n Sn
(74)
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
21 43
Therefore, c w Sw c w Sn + = Cw + Cn (75) X X where Cw and Cn are mass fractions of wetting- and nonwetting-phase of the system, respectively. It is noted that, 1=
Cw = 1 − Cn
(76)
ith
component, zi , in terms of one phase (wetting phase) mass The total mole fraction of fraction and the wetting- and nonwetting-phase molar fractions, is given by, zi = Cw xwi + (1 − Cw ) xni ,
i = 1, · · · , N
(77)
The pressure equation can be obtained, using the concept of volume-balance, as follows, φC f
N N ∂p + ∑ V¯i ∇ · (cw xwi uw + cn xni un ) = ∑ V¯i Fi , ∂t i=1 i =1
i = 1, · · · , N
(78)
where C f is the total fluid compressibility and Vi is the total partial molar volume of the ith component. The distribution of the each component inside the two phases is restricted to the stable thermodynamic equilibrium in terms of phases’ fugacities, f wi and f ni of the ith component. The stable thermodynamic equilibrium is given by minimizing the Gibbs free energy of the system Bear (1972); Chen (2007), f wi ( pw , xw1 , xw2 , · · · , xwN ) = f ni ( pn , xn1 , xn2 , · · · , xnN ), The fugacity of the
ith
i = 1, · · · , N
(79)
component is defined by, f αi = pα xoi φαi ,
α = w, n,
i = 1, · · · , N
(80)
φαi , α = w, n is the fugacity coefficient of the ith component which will be defined below. The phase and volumetric behaviors, including the calculations of the fugacities, are modeled using the Peng-Robinson equation of state (Peng & Robinson, 1976). Introducing the pressure of the phase, p/ al pha, which is given by Peng-Robinson two-parameter equation of state as, pα = aα =
N
RT aα ( T ) − , Vα − bα Vα (Vα + bα ) + bα (Vα − bα ) N
∑ ∑ xiα x jα (1 − κij )
i =1 j =1
ai a j ,
bα =
N
∑ xiα bi ,
j =1
α = w, n α = w, n
(81) (82)
where R is the universal gas of constant, T is the temperature, Vα is the molar volume of the phase α, κij is a binary interaction parameter between the components i and j, ai and ai are empirical factor for the pure component i given by, ai = Πia αi
R2 Tic2 , pic
bi = Πib
RTic , pic
Tic and pic are the critical temperature and pressure,
i = 1, · · · , N
(83)
22 44
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Πia = 0.45724,
Πib = 0.077796,
2 αi = 1 − λi 1 − TTic ,
λi = 0.37464 + 1.5432ωi − 0.26992ωi2 ,
i = 1, · · · , N
(84)
Eq. (72) can be rewritten in the following cubic form, Zα3 − (1 − Bα ) Zα2 + ( Aα − 2Bα − 3Bα2 ) Zα − ( Aα Bα − Bα2 − Bα2 ) = 0,
α = w, n
(85)
where Zα is the compressibility factor given by, bα Vα (86) , α = w, n RT (Chen, 2007) explained how to solve the cubic algebraic equation, Eq. (64). The fugacity coefficient φαi of the ith component is defined in terms of the compressibility factor Zα as, √ N 2 ln φαi = bbαi ( Zα − 1) − ln( Zα − Bα ) − √Aα x jα (1 − κij ) ai a j − bbαi ∑ = 1 j a α 2 2Bα √ (87) · ln Zα +(1+√2) Bα Zα =
Zα −(1− 2) Bα
Deriving of this equation can be found in details in (Chen, 2007). Using Eqs. (51)- (53) and (62)- (65) with some mathematical manipulation one can find, ∂(φρw Sw ) dpc = −∇ · ρw f w (S) Kmn (S) ∇Sw − Δρg∇z + u + qw (88) ∂t dSw Alternatively, in terms of pressure the flow equations may be rewritten in the form, Kkrw ∂(φρw Sw ) ∂pn ∂pw − = ∇ · ρw (∇ pw − ρw g∇z) + qw dpc ∂t ∂t μw Kkrn ∂pw ∂(φρn (1 − Sw )) ∂pn − = ∇ · ρn (∇ pn − ρn g∇z) + qn dpc ∂t ∂t μn
(89) (90)
Both models, Eq. (88) and Eqs. (89)- (90) are used intensively especially in the field of oil reservoir simulations. 6.2 Three-phase compositional flow
In three-phase compositional flow the governing equations will not has a big difference from the two-phase case. In this section we introduce the main points which distinguish the three-phase flow. On the other hand, we consider the black oil model as an example of the three-phase compositional flow instead of considering the general case to investigate such kind of complex flow. The black oil model is water-oil-gas system such that water represents the aqueous phase and oil represents oleic phase. The hydrocarbon in a reservoir is almost consists of oil and gas. Water is being naturally in the reservoir or injected in the secondary stage of oil recovery. Also, gas may be found naturally or/and injected as CO2 injection for the enhanced oil recovery stage. The governing equations may be extended to the three-phase flow. The generalized Darcy’s law with mass transfer equations will remain the same as in Eqs. (30) and (31) with considering α = w, o, g, thus each phase is represented by two equations, continuity and momentum. The index α denotes to the water (w), oil (o) and gas (g), respectively. The solute transport equations is modified to suite the three-phase compositional flow as follow,
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
∂(φczi ) + ∇ · cw xwi uw + co xoi uo + c g x gi u g = Fi , ∂t
or ∂ ∂t
i = 1, · · · , N
φ cw xwi Sw + co xoi So + c g x gi Sg + ∇ · cw xwi uw + co xoi uo + c g x gi u g = xwi qw + xoi qo + x gi q g ,
i = 1, · · · , N
23 45
(91)
(92)
Following (Stone, 1970; 1973) we assume that the water-oil and oil-gas relative permeabilities are given as the two-phase case, nw Sw − Swc (93) krw (Sw ) = k0rw 1 − Swc − Sorw ng Sg − Sgr krg (Sg ) = k0rg (94) 1 − Swc − Sorg − Sgr where Swc is the connate water saturation, Sorg is the residual oil saturation to gas, Sorw is the residual oil saturation to water, Sgr is the residual gas saturation to water. Sw = 1 − Sorw . The intermediate-wetting phase (oil phase) relative permeabilities are given by, 1 − Sw − Sorw now 0 krow (Sw ) = krow (95) 1 − Swc − Sorw 1 − Swc − Sorg − Sg nog krog (Sg ) = k0rog (96) 1 − Swc − Sorg − Sgr The intermediate-wetting phase relative permeability is given by, krow krog (97) k norm k norm may be setting as one or given by another formula as in the literature which will not mention here for breif. kro (Sw , Sg ) =
6.3 Numerical methods for multi-phase flow
Much progress in the last three decades in numerical simulation of multi-phase flow with compositional and chemical effect. Both first-order finite difference and finite volume methods are used. First-order finite difference schemes has numerical dispersion issue, while the first-order finite volume has powerful features when used for two-phase flow simulation (Leveque, 2002). However, the later one has some limitations when applied to fractured media (Monteagudo & Firoozabadi, 2007). Also, higher-order methods have less numerical dispersion and more accurate flow field calculations than the first-order methods. The combined mixed-hybrid finite element (MHFE) and discontinuous Galerkin (DG) methods have been used to simulate two-phase flow by (Hoteit & Firoozabadi, 2005; 2006; Mikyska & Firoozabadi, 2010). In the combined MHFE-DG methods, MHFE is used to solve the pressure equation with total velocity, and DG method is used to solve explicitly the species transport equations. Therefore, the parts are coupled using scheme such as the iterative IMplicit Pressure and Explicit Concentration (IMPEC) scheme. Also, (Sun et al., 2002) have used combined MHFE-DG methods to miscible displacement problems in porous media.
24 46
Transfer Mass Transfer in Multiphase Systems andMass its Applications
The DG method (Wheeler, 1987; Sun & Wheeler, 2005a;b; 2006) is derived from variational principles by integration over local cells, thus it is locally mass conservative by construction. In addition, the DG method has low numerical diffusion because higher-order approximations are used within cells and the cells interfaces are weakly enforced through the bilinear form. DG method is efficiently implementable on unstructured and nonconforming meshes. The MHFE methods are based on a variational principle expressing an equilibrium or saddle point condition that can be satisfied locally on each element (Brezzi & Fortin, 1991). It has an indefinite linear system of equations for pressure (scalar) and the total velocity (vector) but they definitized by appending as extra degrees of freedom the average pressures at the element edges.
7. References Aissa, W. A. & Mohammadein, A. A. (2006). Chemical reaction effects on combined forced and free convection flow of water at 4 c past a semi-infinite vertical plate, J. Eng. Sci. Assiut Univ. 34: 1225–1237. Bear, J. (1972). Dynamics of Fluids in Porous Media, Elsevier, New York. Brezzi, F. & Fortin, M. (1991). Mixed and hybrid finite element methods, Springer–Verlag, New York. Brooks, R. H. & Corey, A. T. (1964). Hydraulic properties of porous media, Hydrology Papers 3. Chen, Z. (2007). Reservoir simulation: mathematical techniques in oil recovery, SIAM, USA. Cheng, P. (1978). Heat transfer in geothermal systems, Advances in Heat Transfer 14: 1–105. Cheng, P. (1981). Thermal dispersion effects on non-darcy convection flows in a saturated porous medium, Lett. Heat Mass Transfer 8: 267–270. Dhir, V. K. (1994). Boiling and two-phase flow in porous media, Annu. Rev. Heat Transfer 5: 303–350. Doughty, C. & Pruess, K. (1988). A semianalytical solution for heat-pipe effects near high-level nuclear waste packages buried in partially saturated geological media, Int. J. Heat Mass Transfer 31: 79–90. El-Amin, M. F. (2004). Double dispersion effects on natural convection heat and mass transfer in non-darcy porous medium, Appl. Math. Comp. 156: 1–17. El-Amin, M. F., Aissa, W. A. & Salama, A. (2008). Effects of chemical reaction and double dispersion on non-darcy free convection heat and mass transfer, Transport in Porous Media 75: 93–109. Elbashbeshy, E. M. A. (1997). Heat and mass transfer along a vertical plate with variable surface tension and concentration in the presence of magnetic field, Int. J. Eng. Sci. Math. Sci. 4: 515–522. Hassanizadeh, S. M. & Gray, W. (1979a). General conservation equations for multi-phase systems 2. mass, momenta, energy and entropy equations, Advances in Water Resources 2: 191–208. Hassanizadeh, S. M. & Gray, W. (1980). General conservation equations for multi-phase systems 3. constitutive theory for porous media, Advances in Water Resources 3: 25–40. Hassanizadeh, S. M. & Gray, W. G. (1979b). General conservation equations for multi-phase systems 1. averaging procedure, Advances in Water Resources 2: 131–144. Herwig, H. & Koch, M. (1991). Natural convection momentum and heat transfer in saturated highly porous mediaan asymptotic approach, Heat Mass Transfer 26: 169–174. Hong, J. T. & Tien, C. L. (1987). Analysis of thermal dispersion effect on vertical plate natural convection in porous media, Int. J. Heat Mass Transfer 30: 143–150.
Solute Transport Transport With in in Singleand Multi-Phase Flow in Porous Media Solute WithChemical ChemicalReaction Reaction Singleand Multi-Phase Flow in Porous Media
25 47
Hoteit, H. & Firoozabadi, A. (2005). Multicomponent fluid flow by discontinuous galerkin mand mixed methods in unfractured and fractured media, Water Resour. Res. 41: W11412. Hoteit, H. & Firoozabadi, A. (2006). Compositional modeling by the combined discontinuous galerkin mand mixed methods, SPE Journal . Lai, F. C. & Kulacki, F. A. (1989). Thermal dispersion effect on non-darcy convection from horizontal surface in saturated porous media, Int. J. Heat Mass Transfer 32: 971–976. Leal, L. G. (2007). Advanced transport phenomena, Cambridge University Press. Leveque, R. J. (2002). Finite volume methods for hyperbolic problems, Cambridge Texts in Applied Mathematics, Cambridge University Press. Mikyska, J. & Firoozabadi, A. (2010). Implementation of higher-order methods for robust and efficient compositional simulation, J. Comput. Physics 229: 2898–2913. Monteagudo, J. E. P. & Firoozabadi, A. (2007). Control-volume model for simulation of water injection in fractured media: incorporating matrix heterogeneity and reservoir wettability effects, SPE Journal . Mulolani, I. & Rahman, M. (2000). Similarity analysis for natural convection from a vertical plate with distributed wall concentration, Int. J. Math. Math. Sci. 23: 319–334. Murthy, P. V. S. N. & Singh, P. (1997). Thermal dispersion effects on non-darcy natural convection with lateral mass flux, Heat Mass Transfer 33: 1–5. Nolen, J. S. (1973). Numerical simulation of compositional phenomena in petroleum reservoirs, Reprint Series, SPE, Dallas, 11, 268284. Peng, D.-Y. & Robinson, D. B. (1976). A new two-constant equation of state, Industrial and Engineering Chemistry Fundamentals 15: 59–64. Plumb, O. A. (1983). The effect of thermal dispersion on heat transfer in packed bed boundary layers, In: Proc. 1st ASME/JSME Thermal Engng. Joint Conf., Vol. 2, pp. 17–21. Pooladi-Darvish, M. & Firoozabadi, A. (2000). Co-current and counter-current imbibition in a water-wet matrix block, SPE Journal 5: 3–11. Prasad, K. V., Abel, S. & Datti, P. S. (2003). Diffusion of chemically reactive species of a non-newtonian fluid immersed in a porous medium over a stretching sheet, Int. J. Non-Linear Mech. 38: 651–657. Salama, A. & van Geel, P. J. (2008a). Flow and solute transport in saturated porous media: 1 the continuum hypothesis, J Porous Media 11: 403–413. Salama, A. & van Geel, P. J. (2008b). Flow and solute transport in saturated porous media: 2 violating the continuum hypothesis, J Porous Media 11: 421–441. Starikovicius, V. (2003). The multiphase fl ow and heat transfer in porous media, Berichte des Fraunhofer ITWM 55: 1–30. Stone, H. (1970). Probability model for estimating three-phase relative permeability, JPT 214. Stone, H. (1973). Estimation of three-phase relative permeability and residual oil data, J. Cdn. Pet. Tech. 13: 53. Sun, S., Riviere, B. & Wheeler, M. F. (2002). A combined mixed finite element and discontinuous galerkin method for miscible displacement problems in porous media, Proceedings of International Symposium on Computational and Applied PDEs, Zhangjiajie National Park of China, 321-341. Sun, S. & Wheeler, M. F. (2005a). Discontinuous galerkin methods for coupled flow and reactive transport problems, Appl. Num. Math. 52: 273–298. Sun, S. & Wheeler, M. F. (2005b). Symmetric and nonsymetric discontinuous galerkin methods for reactive transport in porous media, SIAM J. Numer. Anal. 43: 195–219.
26 48
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Sun, S. & Wheeler, M. F. (2006). Analysis of discontinuous galerkin methods for multi-components reactive transport problem, Comput. Math. Appl. 52: 637–650. Telles, R. S. & V.Trevisan, O. (1993). Dispersion in heat and mass transfer natural convection along vertical boundaries in porous media, Int. J. Heat Mass Transfer 36: 1357–1365. Udell, K. S. (1985). Heat transfer in porous media considering phase change and capillarity – the heat pipe effect, Int. J. Heat Mass Transfer 28: 485–495. van Genuchten, M. (1980). A closed-form equation for predicting the hydraulic conductivity of unsaturated soils, Soil Sci. Soc. Am. J. 44: 892–898. Wheeler, M. F. (1987). An elliptic collocation finite element method with interior penalties, SIAM J. Numer. Anal. 15: 152–161. Whitaker, S. (1967). Diffusion and dispersion in porous media, AIChE 13: 420–427. Whitaker, S. (1977). Simultaneous heta, mass, and momentum transfer in porous media: A theory of drying, Advances in Heat Transfer 13: 119–203. Young, L. C. & Stephenson, R. E. (1983). A generalized compositional approach for reservoir simulation, SPE Journal 23: 727–742.
0 3 Multiphase Modelling of Thermomechanical Behaviour of Early-Age Silicate Composites Jiˇr´ı Vala Brno University of Technology, Faculty of Civil Engineering Czech Republic
1. Introduction The reliable prediction of thermomechanical behaviour of early-age silicate composites is a complicated multiphysical and multiscale problem, containing a lot of open questions. However, silicate mixtures, namely fresh concrete, are the most commonly used materials in building constructions throughout the world, thus such prediction is of great practical significance. The most important modelling outputs are the macroscopic effective strain, stress, temperature, moisture etc. time evolutions, driven by chemical reactions of particular clinker minerals with water. Every realistic model is then expected to include thermo-, chemoand hygromechanical processes and phase changes, involving all available microstructural information related to the real porous medium. The deformation of a material sample or a building construction made from silicate composites has to be analyzed at least as the superposition of – reversible elastic deformation, – viscous material flow, – volume changes, unlike remaing contributions independent of external loads. The crucial external and internal influences are: – internal hydration heat, generated by the hydration hydraulic processes, – ambient temperature variation, connected with ambient humidity variation (natural or artificial ones), – external mechanical loads. The significant physical (and chemical) processes are: a) thermal deformation, b) autogenous shrinkage, c) carbonation, d) elastic and creep deformation, e) additional thermal deformation, f) drying shrinkage and swelling.
2 50
Transfer Mass Transfer in Multiphase Systems andMass its Applications
In the first period of intense hydration a), accompanied by b), is dominant. In the later period the role of a) decreases, but the effect of c) has to be taken into account. The external mechanical loads cause d) (creep especially in the earliest age), the external temperature changes simultaneously force e), modified by f). The traditional approach to the modelling of such complex physical and technical problems is the phenomenological one, as discussed in (Baˇzant, 2001): the effect of changes of density, porosity, permeability, compressive strength, etc. on material behaviour is lumped together to some model parameters, which must be identified by long-lasting tests in the whole range of model applicability. On the contrary, the so-called CCBM (“Computational Cement-Based Material”) approach, suggested in (Maruyama et al., 2001), develops the original idea of (Tomosawa, 1997): the slight generalization of its (seemingly simple) form ˙ = Φ(, ∗ ) ,
˙ ∗ = Ψ(, ∗ )
where is the radius of an unhydrated cement particle, ∗ its total radius including hydrate, dot symbols refer (everywhere in this chapter) to derivatives with respect to the time t ≥ 0 and Φ, Ψ are (in general rather complicated) material characteristics with hidden , ∗ (but not with their time derivatives) again. The analysis of (Maruyama et al., 2001) assumes ideal spherical particles, hydration products adherent to such particles (whose size distribution is approximated by a special Rosin-Ramler function), water diffusing through the hydrate layer and chemically reacting with cement, up to interparticle contact effects; the amount of water is controlled by the pore structure, modified by hydration reactions of cement constituents and corresponding heat generation. Particular cement constituents, namely alite (C3 S, typically 65 % of the total mass in the Portland cement), belite (C2 S, 15 %), aluminate phase (C3 A, 7 %), ferrite phase (C4 AF, 8 %), etc., have their own densities and hydration reactions, generating hydration heat. For various types of cement we have different hydration degree Γ, introduced as Γ :=
μh h μ∞
where μh denotes the (usually increasing) mass of skeleton (and corresponding sink of liquid h the final mass of hydrated (chemically combined) water in a volume unit; water mass) ans μ∞ alternatively (cf. (Gawin et al., 2006a), p. 309) Γ :=
Qh h Q∞
h . However, it in terms of the heat Qh released during hydration and of its final value Q∞ is difficult to guarantee above sketched model assumption in building practice, applying also (not single-sized) additional aggregate; thus Γ is usually quantified from macroscopic experiments (as adiabatic calorimetric or isothermal strength evolution tests) not from such microstructural considerations. Consequently Γ can be evaluated by (Gawin et al., 2006a), p. 309, from an auxiliary evolution problem of type
Γ˙ = A(Γ, φ, T ) with an a priori known real function A.
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
3 51
During the same hydration process the non-negligible vapour mass source μe , caused by the liquid water evaporation or desorption, occurs, too. Unfortunately, unlike μh , no reasonable constitutive relation is available for the direct evaluation of μe . Clearly, the reliable prediction of material behaviour applicable to real building objects during hydration needs some multiscale analysis. The mechanistic approach (Pichler et al., 2007) makes it possible to consider above sketched effects explicitly because they appear directly in the model equations, distinguishing between 4 length scales, characterized as I) anhydrous-cement scale (typical length of a representative volume element from 10-8 to 10-6 m), in more details decomposed into 3 subscales, where the qualitative estimate of activity of four main clinker phases, water and air requires the detailed micromechanical evaluation of corresponding chemical reactions, II) cement-paste scale (from 10−6 to 10−4 m), III) mortar scale (about 10−2 m), IV) macroscale (about 10−1 m). The analysis of capillary depression at scale I) (considering membrane forces on solid/liquid, solid/gas and liquid/gas interfaces), of ettringite formation at scale II), of autogenous deformation at scales II) and III), referring to the Hill homogenization lemma (see (Dormieux et al., 2006), p. 105), must be completed by the interpretation of such multiscale results at scale IV). However, different physical and chemical processes studied at particular scales do not admit proper and physically transparent mathematical analysis of two- and more-scale convergence, as discussed in (Cioranescu & Donato, 1999), (Vala, 2006) or (Efendiev et al., 2009), including its non-periodic (formally complicated) generalization, introduced in (Nguentseng, 2003-4). The approach (Gawin et al., 2006a) applies certain mechanistic-type method to obtain the governing equations only, using the averaging hybrid mixture theory: the developments starts at the micro-scale and balance equations for particular phases and interfaces are introduced at this level and then averaged for obtaining macroscopic balance equations. Four phases are distinguished: solid skeleton, liquid water, vapour and dry air, whose densities are considered (under the passive air assumption) as constants; the whole hygro-thermo-chemo-mechanical process is then studied as the time evolution of capillary pressure, gas pressure, temperature and displacement of points related to the reference (initial) configuration, driven by balance equations of classical thermodynamics and conditioned by corresponding constitutive laws. The detailed geometrical analysis (Sanavia et al., 2002) (without phase changes) offers the possibility to extend such considerations beyond the assumption of small deformations and involve some elements of fracture mechanics. The development, laboratory testing and computational simulations of new materials, namely those for the application of advanced engineering structures, belong to the research priorities of the Faculty of Civil Engineering of Brno University of Technology. Moreover, these activities should be intensified thanks to the proposed complex research institution AdMaS (“Advanced Materials and Structures”) in the near future. The long-time behaviour of massive structures, especially its bearing value, durability and user properties, is typically conditioned by the early-age heat, moisture, etc. treatment, modified by foundations, subgrades, reinforcement and connecting members; thus the aim is to design the whole building process to minimize the development of significant tensile stresses to avoid the the danger of cracking, or even to force volume changes and corresponding final stresses appropriate for the future use of a structure. The deeper understanding of decissive
4 52
Transfer Mass Transfer in Multiphase Systems andMass its Applications
processes in early-age materials that effects volume changes is therefore needed, although no closed physical and mathematical models are available and all simplified calculations contain empirical parameters and functions, whose identification, supported by laboratory measurements or in situ observations, generates separate non-trivial problems, not discussed in details here. However, we shall demonstrate how the thermomechanical analysis of balance of mass, (linear and angular) momentum and energy for computational HAM (“heat, air and moisture”) models in civil engineering is able to be extended to a complex computational model, including the mass source or solid skeleton related to the hydration process (and corresponding sink of liquid water mass), as well as the vapour mass source caused by the liquid water evaporation or desorption, using some micromechanical arguments from the theory of porous media.
2. Mixture components To analyze the phase changes in an early-age silicate composite, we shall consider four material phases: – solid material, identified by an index s, – liquid water, identified by an index w, – water vapour, identified by an index v, – dry air, identified by an index a. In addition to partial derivatives of scalar quantities ψ with respect to time, i. e. ψ˙ := ∂ψ/∂t , we shall introduce also the partial derivatives of such quantities with respect to xi , i ∈ {1, 2, 3}, x = ( x1 , x2 , x3 ) being a Cartesian coordinate system in the three-dimensional Euclidean space R3 , ψ,i := ∂ψ/∂x j . In the case of real vector variables with values in R3 we shall write ψ briefly instead of (ψ1 , ψ2 , ψ3 ). Even in the case of matrix variables in the with values in R3×3 , the space of real matrices of the third order, we shall write ψ only instead of ψij , i, j ∈ {1, 2, 3}. Consequently, due to the preceding notation, unlike the matrix elements ψij from ψ ∈ R3×3 with i, j ∈ {1, 2, 3}, we have e. g. for ψ ∈ R3 ψi,j := ∂ψi /∂x j . We shall assume that the scale bridging between particular scales (if relevant scale material data are available) can be done by means of the averaging of model variables. The basic (averaged) variables in our model, related to a representative volume element, are: – 4 intrinsic phase densities R = (ρs , ρw , ρv , ρ a ), – 12 components of phase velocities V = (vis , viw , viv , via ) with i ∈ {1, 2, 3}, – 3 fluid pressures P = ( pw , pv , p a ), – 1 (absolute) temperature ϑ.
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
5 53
Intrinsic phase densities evidently do not reflect the amount of particular phases in a volume unit; thus it is useful to define (real) phase densities ρε := η ε ρε formally for any phase index ε ∈ {s, w, v, a} where η s = (1 − n ) , η w = ns , η v = n (1 − s ) , η a = n(1 − s)(1 − φ) . Unfortunately it is not easy to evaluate the porosity n, the saturation degree s and the relative humidity (the volume fraction occupied by water vapour in the total gaseous phase) φ. ´ Nevertheless, similarly to ρε , ε ∈ {s, v, w, a}, being motivated by the Dalton law by (Bermudez de Castro, 2005), p. 111, we can also introduce pressures pε := η ε pε . We can evaluate also the “macroscopic” mixture density ρ := ρs + ρw + ρv + ρ a . Let us also remark that, from he point of view of solid phase, fluid pressures P are accompanied by a (partial) Cauchy stress tensor compound from components τij with i, j ∈ {1, 2, 3}, whose (indirect) relation to V will be discussed later. The porosity can be evaluated from the finite strain analysis by (Sanavia et al., 2002), p. 139. The multiphase medium at the macroscopic level can be described as the superposition of all phases ε, whose material point with coordinates xiε0 in the reference configuration Ω in R3 occupies a point with coordinates xiε (t); zero indices are related to the reference configuration, here in the initial time t = 0. In the Lagrangian description of the motion the position of each material point can be expressed as xiε (t) = xiε0 + uiε ( xiε0 , t) where uiε ( xiε0 , t) denotes the displacement at chosen time and zero indices are related to a reference configuration, here in time t = 0. Thus Fijε ( x ε0 , t) :=
∂xiε ( x ε0 ) ∂x ε0 j
= δij +
∂uiε ( x ε0 , t) ∂x ε0 j
can be taken as a deformation characteristic, δ being a Kronecker symbol, consequently n = 1 − (1 − n0 ) (det F s )−1 where n0 ( x s0 ) denotes the porosity in the reference configuration. In the linearized geometry this access in not available: e. g. (Gawin et al., 2006a), p. 310 presents an empirical (nearly linear) function n(Γ), justified by the correlation analysis, exploiting the experimental database of (De Schutter, 2002) where hardening cement pastes with 5 different values of water/cement ratio are studied.
6 54
Transfer Mass Transfer in Multiphase Systems andMass its Applications
The saturation degree s comes from the microporomechanical considerations (cf. (Dormieux et al., 2006), p. 247); their usual result (verified by laboratory measurements) is the so-called sorption isotherm, a real function s( pc ) where pc is the capillary pressure, determined (in general) as pc = Ξ( pw , pv , p a ) for certain real function Ξ. For temperatures normally encountered in building structures and for capillary saturation range (Gawin et al., 2006a), pp. 305 and 311, recommends the simplified relation pc = pv + p a − pw , justified by an exploitation of the entropy inequality by means of the Coleman-Noll method; for more details and substantial generalizations see (Gray, 2000), p. 482. To formulate the basic balance laws of classical thermodynamics, consequently the announced system of partial differential or integral equations of evolution, let us introduce the simple notation of (Vala, 2006), p. 33, applied to particular phases identified by indices ε ∈ {s, w, v, a}. If ω ε is a source corresponding to a scalar quantity ψε then the conservation of a scalar quantity ψε reads ψ˙ ε + (ψε viε ),i = ω ε ; (1) this will be exploited in the following three sections.
3. Mass balance For an arbitrary ε ∈ {s, w, v, a} let us insert a scalar quantity ψε = ρε and a corresponding source term ω ε into (1) where ω s = −μ˙ h , ω w = μ˙ h − μ˙ e , ω v = μ˙ e , ωa = 0 . To simplify our notations, we shall apply the Einstein summation convention for indices from the set {1, 2, 3} without additional explanations, e. g. in the following equation the sum over j ∈ {1, 2, 3} is omitted formally. The resulting system of partial differential equations of evolution is ρ˙ s + (ρs vsj ),j = −μ˙ h , h e ρ˙ w + (ρw vw j ),j = μ˙ − μ˙ ,
ρ˙ v + (ρv vvj ),j ρ˙ a + (ρ a v aj ),j
(2)
= μ˙ , e
= 0.
Let us notice (here and similarly for other balance laws, too, without explicit comments) that the system (2) contains the standard left-hand-side additive terms, well-known e. g. from ´ (Bermudez de Castro, 2005), p. 4 (for one phase), and from (Dormieux et al., 2006), p. 9 (for
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
7 55
more phases), supplied by the additional right-hand-side additive terms, containing variables μh , determined from the hydration degree Γ, and μe , a priori unknown. For the effective numerical calculations, finite element techniques (cf. (Efendiev et al., 2009), p. 47) or finite volume ones (cf. (Efendiev et al., 2009), p. 52) should be applied. Therefore we need to rewrite (2) (and analogous equations in the following sections) into the integral form, able to include boundary conditions in a simple way. Let ∂Ω be the boundary of a domain Ω in R3 . Let us introduce the additional notation
(ς, ψ) := ς, ψ :=
Ω
ς( x )ψ( x ) dx ,
∂Ω
ς( x )ψ( x ) ds( x )
for any functions ς and ψ (integrable in the needed sense) where dx refers to the standard Lebesgue measure and ds( x ) to the surface Hausdorff measure. The integration by parts (based on the Green-Ostrogradskii theorem) then gives
(ς, ρ˙ s ) + ς, ρs vsj νj − (ς ,j , ρs vsj ) = −(ς, μ˙ h ) , w h e (ς, ρ˙ w ) + ς, ρw vw j νj − ( ς ,j , ρw v j ) = ( ς, μ˙ − μ˙ ) ,
(ς, ρ˙ v ) + ς, ρv vvj νj − (ς ,j , ρv vvj ) (ς, ρ˙ a ) + ς, ρ a v aj νj − (ς ,j , ρ a v aj )
(3)
= (ς, μ˙ ) , e
= 0
for any test function ς (more precisely: sufficiently smooth, otherwise only in sense of distributions, from an appropriate function space which may be problem-specific); ν( x ) = (ν1 ( x ), ν2 ( x ), ν3 ( x )) means the local unit outward normal vector on (sufficiently smooth) ∂Ω.
4. Momentum balance The momentum balance includes the linear balance and the angular balance. Since we consider a non-polar continuum, the second one forces only the symmetry of any Cauchy stress tensor τ. It remains to apply the first one. For an arbitrary ε ∈ {s, w, v, a} and (step-by-step) for particular i ∈ {1, 2, 3} let us insert a scalar quantity ψε = ρε viε and a corresponding source term ε ω ε = σij,j + ρε ( gi − aiε + θiε )
into (1) where for the solid phase and
σijs = τij σijε = −δij pε
for all other phases with ε ∈ {w, v, a}, the acceleration g = ( g1 , g2 , g3 ) generates ρε g, the volume density of a gravitational force, the acceleration aε = ( a1ε , a2ε , a3ε ), corresponding to the velocity
8 56
Transfer Mass Transfer in Multiphase Systems andMass its Applications
vε = (v1ε , v2ε , v3ε ), generates the volume density of an inertia force, and the acceleration θiε = (θ1ε , θ2ε , θ3ε ) generates the volume density due to mechanical interaction with other phases. The total Cauchy stress, introduced (unlike the partial Cauchy stress τ) as σ := σs + σw + σv + σ a , then has the components
σij = τij − δij ( pw + pv + p a ) .
The Clapeyron law (see (Gawin et al., 2006a), p. 305) enables us to evaluate both gas pressures pv and p a (consequently pv and p a , too) as certain functions pv (ρv , ϑv ) and p a (ρ a , ϑ a ). Unfortunately, for the remaining pressure pw (or pw ) we do not know such constitutive relation. In the linear momentum balance equations we need to calculate all velocities vε and accelerations aε from corresponding displacements uε , ε ∈ {s, w, v, a}. By the chain rule we have ε viε ( x ε0 , t) = u˙ iε ( x ε0 , t) + ui,j ( x ε0 , t) vεj ( x ε0 , t) , ε ( x ε0 , t) vεj ( x ε0 , t) . aiε ( x ε0 , t) = v˙ iε ( x ε0 , t) + vi,j ε vε and vε vε , can be understood in the sense of scalar products grad uε · vε , The terms ui,j j i,j j ε ε grad v · v by (Sanavia, 2001), p. 139 (though the construction of such general grad-operator is not quite trivial). More precisely, the geometry of structured continua is described using fiber bundles and Riemanian manifold in (Yavari & Marsden, 2009), p. 8. Another ´ approach, explained in (Bermudez de Castro, 2005), p. 195, results in the ALE (“Arbitrary ´ Lagrangian-Eulerian”) formulations by (Bermudez de Castro, 2005), p. 195. Nevertheless, both such generalizations lead to complicated, reader-unfriendly expressions. The classical constitutive relation for the solid phase between τ, us , vs , etc., considers a linearized sufficiently small strain tensor and its additive decomposition into several parts, typically to the linear elastic and the power-law viscoelastic (creep) ones, containing facultative corrections due to microcracking, as in (Gawin et al., 2006a), p. 343, and (in more details) in (Gawin et al., 2006b), p. 519, with help of special mechanical and chemical damage parameters. The finite deformation theory needs some multiplicative decomposition of F s in the form F s = F s1 F s2 . . . F sM
into a finite number M > 1 of matrix components; the constitutive relation is then characterized by a function τ ( F s1 , . . . , F sM , F˙ s1 , . . . , F˙ sM , . . .) . Especially in the case M = 2 (Sanavia et al., 2002), p. 143 combines the first standard reversible elastic component with the second irreversible one from the Drucker-Prager plasticity model with linear isotropic hardening, Neff (2008) combines elasticity with nonlocal linear kinematic hardening due to dislocation interaction, etc. Recently Majorana (2010) suggests even M = 9, taking into account i) elastic deformation, ii) plastic deformation, iii) damage, iv) cracking, v) creep, vi) shrinkage, vii) lits, viii) thermal strain, ix) autogenous strain, covering most items a)-e) from Introduction. However, for all simulation of real processes the theoretical extent of such decomposition must be supported by the competence in the laboratory identification
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
9 57
of needed material characteristics and in the estimate of their uncertainty, imported into constitutive relations. The evaluation of θis , θiw , θiv and θia for all i ∈ {1, 2, 3} comes from the Darcy law, whose general (nonlinear) form, following (Dormieux et al., 2006), p. 50, based on the knowledge of certain material functions F1 , F2 and F3 , valid for each ε ∈ {w, v, a}, is viε − vis = Fiε (θ1ε , θ2ε , θ3ε , pε , η ε ) . The special (linear) form of these relations, suggested in (Sanavia, 2001), p. 9 (this part of (Sanavia, 2001) contains much more technical details than its later revision (Sanavia et al., 2002)), is Kijε (ρε θ jε − p,jε ) + κ ε η ε (viε − vis ) = 0 where, for a fixed ε ∈ {w, v, a}, Kijε are components of a symmetric permeability matrix and κ ε is a (positive) dynamic viscosity. Such constitutive relations have to be supplied by the constraint by (Sanavia, 2001), p. 8, θis + θiw + θiv + θia = 0 . The resulting system of partial differential equations of evolution, unified (for brevity) for all ε ∈ {w, v, a} and i ∈ {1, 2, 3} is
(ρε viε )˙ + (ρε viε vεj ),j = − p,iε + ρε ( gi − aiε + θiε ) .
(4)
For the solid phase we receive similarly for all i ∈ {1, 2, 3}
(ρs vis )˙ + (ρs vis vsj ),j = τij,j + ρs ( gi − ais + θiw + θiv + θia ) .
(5)
We can see that for negligible values of all components of vs and θ s (5) this result degenerates to classical Cauchy equilibrium conditions, well-know in building statics (with zero as ) and dynamics (with nonzero as ), ρs ais + τij,j = −ρs gi . Let us repeat the approach with a test function ς from the previous section and apply it to (4) and (5). For any i ∈ {1, 2, 3} the integration by parts with ε ∈ {w, v, a} gives
(ς, (ρε viε )˙) + ς, ρε viε vεj νj − (ς ,j , ρε viε vεj ) ε
ε
= −ς, p νi + (ς ,i , p ) + (ς, ρε ( gi −
aiε
(6)
+ θiε )) ,
whereas for the solid phase the analogous result is
(ς, (ρs vis )˙) + ς, ρs vis vsj νj − (ς ,j , ρs vis vsj ) = ς, τij νj − (ς ,j , τij ) + (ς, ρs ( gi − for any test function ς.
ais
− θiw
(7)
− θiv
− θia ))
10 58
Transfer Mass Transfer in Multiphase Systems andMass its Applications
5. Energy balance Let us introduce four (in general temperature-variable) heat capacities cε (ϑ ) as prescribed material characteristics and four heat fluxes qε = (q1ε , q2ε , q3ε ) as additional variables. Similarly to the mass balance, for an arbitrary ε ∈ {s, w, v, a}, let us insert a scalar quantity ψε =
1 ρε (viε )2 + ρε cε ϑ 2
and a corresponding source term ε ω ε = (σij,j + qiε ),i + (ρε ( gi − aiε + θiε )),i + ε
into (1) where the exchange of energy between phases is accounted using the additive terms s = −μ˙ h ξ h , w = μ˙ h ξ h − μ˙ e ξ e , v = μ˙ e ξ e , a = 0 ´ de Castro, 2005), p. 110): ξ h that with specific enthalpies ξ h and ξ e (introduced in (Bermudez of hydration (related to the mass unit of chemically bound water) and ξ e that of evaporation, following (Gawin et al., 2006a), p. 303. The resulting system of partial differential equations of evolution is
(ρs vis vis + 2ρs cs ϑ)˙ + ((ρs vis vis + 2ρs cs ϑ)vsj ),j s = 2τij,ij − 2qi,i + 2(ρs ( gi − ais − θiw − θiv − θia )),i − 2μ˙ h ξ h , (ρw viw viw + 2ρw cw ϑ)˙ + ((ρw viw viw + 2ρw cw ϑ)vw j ),j w w = −2pi,i − 2qi,i + 2(ρw ( gi − aiw + θiw )),i + 2μ˙ h ξ h − 2μ˙ e ξ e , (ρv viv viv + 2ρv cv ϑ)˙ + ((ρv viv viv + 2ρs cw ϑ)vvj ),j
(8)
v v = −2pi,i − 2qi,i + 2(ρv ( gi − aiv + θiv )),i + 2μ˙ e ξ e , a a s (ρ a vi vi + 2ρs c ϑ)˙ + ((ρ a via via + 2ρs cs ϑ)v aj ),j a a = −2pi,i − 2qi,i + 2(ρv ( gi − aia + θia )),i .
´ All heat fluxes can be computed using the Fourier law by (Bermudez de Castro, 2005), p. 42: in general we have qiε + λijε ϑ,j = 0 for every ε ∈ {s, w, v, a} and i ∈ {1, 2, 3} and prescribed material characteristics λijε (ϑ, ϑ,1 , ϑ,2 , ϑ,3 ) . Supposing that all these characteristics are independent of derivatives of ϑ, in the linearized case the elements λij generate certain symmetrical matrix of real factors, allowed to be functions of ϑ. Under the assumption of isotropy material we obtain moreover λij = λ∗ δij for some real factor λε∗ (ϑ ); this is just the crucial simplification of (Gawin et al., 2006a), p. 313, qiε = −λε∗ ϑ,i .
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
11 59
Repeating the approach with some test function ς again and applying it to (8), from the integration by parts we obtain
(ς, (ρs vis vis + 2ρs cs ϑ)˙) + ς, (ρs vis vis + 2ρs cs ϑ)vsj νj − (ς ,j , (ρs vis vis + 2ρs cs ϑ)vsj ) = 2ς, (τij,j − 2qis )νi − 2(ς ,i , τij,j − 2qis ) + 2ς, ρs ( gi − ais − θiw − θiv − θia )νi − 2(ς ,i , ρs ( gi − ais − θiw − θiv − θia )) − 2(ς, μ˙ h ξ h ) , (ς, (ρw viw viw + 2ρw cw ϑ)˙) w w w w + ς, (ρw viw vi ws + 2ρw cw ϑ)vw j nu j − ( ς ,j , ( ρw vi vi + 2ρw c ϑ ) v j ) = −2ς, ( piw + qiw )νi + 2(ς, i, piw + qiw ) + 2ς, (ρw ( gi − aiw + θiw ))νi − 2(ς ,i , ρw ( gi − aiw + θiw )) + 2(ς, μ˙ h ξ h − μ˙ e ξ e ) , (ς, (ρv viv viv + 2ρv cv ϑ)˙) + ς, (ρv viv viv + 2ρv cv ϑ)vvj νj − (ς ,j , ρv viv viv + 2ρv cv ϑ)vvj )
(9)
= −2ς, ( piv + qiv )νi + 2(ς ,i , piv + qiv ) + 2ς, ρv ( gi − aiv + θiv )νi − 2(ς ,i , ρv ( gi − aiv + θiv )) + 2(ς, μ˙ e ξ e ) , (ς, (ρ a via via + 2ρ a c a ϑ)˙) + ς, (ρ a via via + 2ρ a c a ϑ)v aj )νj − (ς ,j , ρ a via via + 2ρ a c a ϑ)v aj ) = −2ς, ( pia + qia )νi + 2(ς ,i , pia + qia ) + 2ς, ρ a ( gi − aia + θia )νi − 2(ς ,i , ρ a ( gi − aia + θia )) . for any test function ς.
6. Initial and boundary conditions Since the class of admissible problems (moreover, not defined properly yet) is rather large, we shall not try to create a list of all physically reasonable types boundary conditions. However, the following considerations demonstrate the methods of implementation of boundary conditions into above derived systems of evolution. Let us remind the boundary integrals occurring in the integral forms of evolution equations. Those from (3) contain functions ρs vsj νj ,
ρw vw j νj ,
ρv vvj νj ,
ρ a v aj νj ,
those from (6) and (7), in addition to functions ρs vis vsj νj , also functions
ρw viw vw j νj ,
τij νj ,
pw νi ,
ρv viv vvj νj , pv νi ,
ρ a via v aj νj
p a νi ,
finally those from (9) functions in addition to functions ρs vis vis vsj νj ,
ρs viw viw vw j νj ,
ρs viv viv vvj νj ,
ρs via via v aj νj
12 60
Transfer Mass Transfer in Multiphase Systems andMass its Applications
still other functions ρs cs ϑvsj νj ,
ρw cw ϑvw j νj , τij,j νi ,
piw νi ,
qis νi ,
qiw νi ,
ρs gi νi , ρs ais νi , (ρw − ρs )θiw νi ,
ρw gi νi ,
ρv cv ϑvvj νj , piv νi , qiv νi ,
ρ a c a ϑv aj νj ,
pia νi , qia νi ,
ρv gi νi ,
ρ a gi νi ,
ρv aiv νi , (ρv − ρs )θiv νi ,
ρ a aia νi ,
ρw aiw νi ,
(ρ a − ρs )θia νi .
Solutions of the resulting system of equations (3), (6), (7) and (9), supplied by needed constitutive equations, should be included in certain spaces of abstract functions, mapping each time t ≥ 0 to some Sobolev, Lebesgue, etc. function space S . Initial values of all independent variables (whose appropriate choice will be discussed later) are supposed to be prescribed in time t = 0. Boundary conditions on ∂Ω or its part for the resulting system of equations (3), (6), (7) and (9), supplied by needed constitutive equations, can be then divided into three groups: a) conditions built in the definition of spaces V, usually prescribed values of abstract functions from V on ∂Ω (in sense of traces) at any admissible time, b) conditions exploiting the knowledge of above listed functions or their linear combinations, c) other conditions. All subsequent examples work with any x from ∂Ω or its certain part and with arbitrary time t ≥ 0. The typical example of a) is ϑ = ϑ∗ for the a priori known temperature ϑ∗ ( x, t). Another (technically more complicated, but homogeneous) example of a) can be ρvi νi = 0 with the carefully defined “effective” velocity vi := (ρs vis + ρw viw νi + ρ a via νi )/ρ . The classical example of b), known even from elementary statics, is σij νj = f i with i ∈ {1, 2, 3} for the prescribed surface load f ( x, t) = ( f 1 ( x, t), f 2 ( x, t), f 3 ( x, t)) . Indirectly this is a boundary condition for u (or v, etc.), due to stress-strain constitutive relations. Its analogy for heat transfer qi νi = q∗ works with the total heat flux vector q := ρs qs + ρw qw + ρv qv + ρ a q a for the prescribed heat flux q∗ ( x, t).
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
13 61
One could expect a similar result for the total diffusive flux vector r := ρw (viw − vis ) + ρv (viv − vis ) + ρ a (via − vis ) , as applied in (Gawin et al., 2006a), p. 316, but this is limited by the facultative nonlinearity of the Darcy law. If the form of Fiε with i ∈ {1, 2, 3} and ε ∈ {w, v, a}. does not admit the explicit evaluation of all corresponding vectors θ ε as linear combinations of vε − vs , we must refer to c). In general, to satisfy such boundary conditions properly, additional techniques, as the application of Lagrange multipliers, Kuhn-Tucker conditions, etc., are necessary.
7. Exact solutions and iterative algorithms The mathematical solvability of engineering problems, whose formulation comes from physically reasonable and transparent considerations, depends critically on the choice: a) of the set of primary variables, b) of the choice spaces S of functions, abstract functions, etc., c) of the proper formulation of boundary and initial conditions. Nevertheless, our problem of early-age time-dependent behaviour of silicate composites is rather complicated, thus most authors bring new versions of a), applying different mathematical, physical and technical simplifications. From the most simple algebraic relations, avoiding differential and integral calculus completely, referring to empirical relations and selected statistical techniques, as presented in (Moon et al., 2005) or in (Bentz, 2008), through one evolution equation, usually of heat conduction, supplied by a lot of empirical dependencies, justified by extensive experimental works, it is possible to trace the development to such advanced physical and mathematical models, as to the system of 10 differential equations of evolution with 10 primary variables and numerous constitutive relations in (Gawin et al., 2006b), p. 519. To reduce the number of empirical relations, typically motivated by some micromechanical considerations, but not fully compatible with quantitative lower-scale computations, we are ready to work with 20 primary variables. In Mixture components we have introduced 20 variables R, V , P and ϑ. Only 2 of these variables, pv and p a , can be evaluated outside the system of (differential or integral) equations of evolution. On the other hand, regardless of the fact that the proper evaluation of Γ forces solution of an additional ordinary differential equation, no constitutive relations are available just to μe and ϕ. This motivates us to reorder our set of variables slightly, introducing
T = (θ, pw , μe , ϕ) . Therefore we can take R, V and T as primary variables; finally we have 20 primary variables and 20 equations in evolution: (2), (4) with (5) and (8), or (3), (6) with (7) and (9), alternatively. We have noticed that the second version is much more frequently used for numerical computations. Because of the complexity of the problem, the mathematical verification of existence, uniquiness, regularity etc. of solutions of initial and boundary problems, corresponding in the case of weak solutions to (3), (6) with (7) and (9), or in the case of strong (classical) solutions to (2), (4) with (5) and (8), due to admissible classes of initial and boundary conditions, contains a lot of open questions. The crucial problem seems to be just in b), i. e. in the definition of some spaces of (generalized) functions with the good properties, expected for the solutions.
14 62
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Even a very special case with a liquid phase only, whose some important additive terms are neglected, derived directly from (2), (4) and (8), namely ρ˙ w + (ρw vw j ),j = 0 , w w (ρw v1w )˙ + (ρw v1w vw j ),j = − p,1 + ρw ( g1 − a1 ) , w w (ρw v2w )˙ + (ρw v2w vw j ),j = − p,2 + ρw ( g2 − a2 ) , w w (ρw v3w )˙ + (ρw v3w vw j ),j = − p,3 + ρw ( g3 − a3 ) , w w (ρw viw viw )˙ + ((ρw viw viw )vw j ),j = −2pi,i + 2( ρw ( gi − ai )),i ,
generates (with standard constitutive relations) the so-called Navier-Stokes existence and smoothness problem, one of the Millenium Prize Problems, formulated by the Clay Mathematics Institute; for its complete definition see www.claymath.org/millennium/Navier-Stokes Equations/ Official Problem Description.pdf. Although the formal solvability of Navier-Stokes equations is not clear, various methods have been developed successfully to analyze their approximate solutions. This can motivated us to the design of an iterative algorithm for numerical simulation of our much more complex physical (and chemical) process, clearly with expected difficulties in any convergence analysis. The precise form of such iterative algorithm, constructing, step-by-step in time, a finite-dimensional approximation of solution of (3), (6) with (7) and (9), depends substantially on c), discussed briefly in the previous section. However, the main idea, coming from some finite element or finite volume technique and from the Rothe method of discretization in time, at least at a finite time interval, can be: 1. set R, V and T by the initial conditions at t = 0, 2. add a time step length to t, preserving R, V and T , 3. solve R from some linearized version of (3), evaluate the correction ε R of R, 4. solve V from the linearized version of (6 and 7), evaluate the correction ε V of V , 5. solve T from the linearized version of (9), evaluate the correction ε T of T , 6. if ε R , ε V and ε T are sufficiently small, return to 3, 7. if the final time is reached, stop the computation, otherwise return to 2. Evidently, preconditioning, mesh adaptivity, stabilization techniques and other technical manipulations are useful to be implemented into such algorithm to force its robustness and effectivity.
8. Computational simulations Most non-trivial physical and technical studies of the problems of early-age behaviour of silicate composites, or (in particular) of concrete, of mortar pastes, etc., include or refer to some numerical experiment, modelling or simulation, applying finite element or finite (control) volume (rarely finite difference or meshless) techniques together with methods for time discretization, as that of lines, of characteristics or of discretization in time, including some microstructural data. However, no specialized commercial or research software code concentrated to such problems is available; one could expect that the complete development of such a code (in such languages for scientific computing as Fortran or C++) would be expensive and time-consuming and would require a team of specialists in many fields of
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
15 63
knowledge, including those outside information technologies. This results in the following rough classification of typically applied software packages: – commercial software for HAM analysis as WUFI (Fraunhofer Institut Holzkirchen) or DELPHIN (Technische Universit¨at Dresden), – large commercial software systems as ANSYS, ABAQUS, etc. (not very flexible, offering only weak support for specific properties of silicate composites) ˇ – specialized software for computations in civil engineering, namely ATHENA (Cervenka Consulting Prague) for calculations of strain and stress distributions in concrete structures at various stages of their existence, including the concrete/reinforcement cooperation, the prediction of fracture and the behaviour under extreme loads, or CESAR-LCPC (Ram Caddsys Chennai, India) for mechanical, structural and geotechnical calculations involving even certain analysis of phenomena associated with young hardening concrete, – user-friendly environment MATLAB/COMSOL for the support of development of original software.
(a)
(b)
Fig. 1. Distribution of: (a) ϑ ( x1 , x2 ) for fixed x3 at t = 24 s, (b) ϑ ( x1 , x2 ) for fixed x3 at t = 96 s. The attempts to predict long-time properties of concrete and other silicate mixtures from the proper analysis of physical and chemical processes during their hardening at the Faculty of Civil Engineering of Brno University of Technology have its own history, involving all above sketched approaches. The original software is in progress, being still far from covering all above discussed micro- and macrostructural aspects. For illustration see (Vala et al., 2009) with numerical simulation of the time-variable thermomechanical behaviour of a massive concrete bridge structure in the Czech Republic (2.5 m thick slab has been formed in 5 layers in 5 time periods) during first 45 hours of its existence; the thermochemical evaluation of hydration heats corresponds to 9 dominant minerals included in the Portland cement. Another practical example (not published yet) refers to a massive concrete foundation, prepared for the vibrational compactor. Fig. 1-3 document the temperature development in time, using the isotherms for t ∈ {24, 96, 144, 312, 408} s (where their redistribution seems to be most interesting) in one half of a typical cut through such structure, built in successive time steps.
16 64
Transfer Mass Transfer in Multiphase Systems andMass its Applications
(a)
(b)
Fig. 2. Distribution of: (a) ϑ ( x1 , x2 ) for fixed x3 at t = 144 s, (b) ϑ ( x1 , x2 ) for fixed x3 at t = 312 s.
9. Conclusion We have derived a rather general (but physically transparent) model of thermomechanical behaviour of early-age silicate composites, including four phases, their interactions and phase changes. The related software experiments, motivated from building practice, exploit, up to now, only a minor part of this model. We have mentioned some mathematical and numerical difficulties, reflected in the intricacy of software codes. From the practical point of view, even more unpleasant complication are connected with the (often unstable and ill-conditioned) inverse problems of identification of material characteristics, typically as nonlinear functions of several variables, in their reliability and correlation with (often only qualitative) microstructural information – cf. (Aly & Sanjayan, 2009) and Chap. 15 of (Kosmatka et al., 2002), called Volume Changes of Concrete. Simultaneously still other generalization, not built in our theory explicitly, are needed in practically motivated technical calculation, as thermal radiation of buildings, discussed in (Sˇ ˇtastn´ık, 2007), or nonlocal modelling of micro- and macrocracking and damage by (Koz´ak & Vlˇcek, 2005). Continued research seems to require more expensive both laboratory equipments and computer hardware and software, thus its extent depends on the grant support of some complex research project, as that mentioned in Introduction, in the near future.
10. Acknowledgement This research has been partially supported by the Ministry of Education, Youth and Sports of Czech Republic No. MSM 0021630511, and by the project of specific research of Brno University of Technology No. FAST-S-10-17.
MultiphaseModelling Modellingofof Thermomechanical Behaviour of Early-Age Silicate Composites Multiphase Thermomechanical Behaviour of Early-Age Silicate Composites
17 65
Fig. 3. Distribution of ϑ ( x1 , x2 ) for fixed x3 at t = 408 s
11. References Aly, T. & Sanjayan, J. G. Mechanism of early age shrinkage of concretes. Materials and Structures, Vol. 42, 431-468. Baˇzant, Z. P. (2001). Prediction of concrete creep and shrinkage: past, present and future. Nuclear Engineering and Design, Vol. 203, 27-38. Bentz, D. P. (2008). A review of early-age properties of cement-based materials. Cement and Concrete Research, Vol. 38, 196-204. ´ Bermudez de Castro, A. (2005). Continuum Thermomechanics. Birkh¨auser, Boston. Cioranecu, D. & Donato, P. An Introduction to Homogenization. Oxford University Press. De Schutter, G. Influence of hydration reaction on engineering properties of hardening concrete, Materials and Structures, Vol. 35, 453-461. Dormieux, L., Kondo, D. & Ulm, F.-J. (2006). Microporomechanics. John Wiley & Sons, Hoboken (New Jersey). Efendiev, Y. & Hou, T. Y. (2009). Multiscale Finite Element Method – Theory and Applications. Springer, Berlin. Gawin, D., Pesavento, F. & Schrefler, B. A. (2006). Hygro-thermo-chemo/mechanical modelling of concrete at early ages and beyond. International Journal for Numerical Methods in Engineering, Vol. 67, 297-331 (Part I) and 332-363 (Part II). Gawin, D., Pesavento, F. & Schrefler, B. A. (2006). Modelling damage processes of concrete at high temperature with thermodynamics of multi-phase porous media. Journal of Theoretical and Applied Mechanics, Vol. 44, 505-532. Gray, W. G.(2000) Macroscale equilibrium conditions for two-phase flow in porous media. International Journal of Multiphase Flow, Vol. 26, 467-501. Kosmatka, S. H., Kerkhoff, B. & Paranese, W. C. (2002). Design and Control of Concrete Mixtures. Portland Cement Association, Skokie (Illinois). Koz´ak, V. & Vlˇcek, L. (2005). The Weibull stress parameters calibration upon the toughness scaling model between cracks having different constraint. Nuclear Engineering and Design, Vol. 235, 1889–1896.
18 66
Transfer Mass Transfer in Multiphase Systems andMass its Applications
Majorana, C. E. (2010). An approach for modelling concrete spalling in finite strain. Mathematics and Computers in Simulation, Vol. 80, 1694-1712. Moon, J.-H., Rajabipour, F., Pease, B. & Weiss, J. (2005). Autogenous shrinkage, residual stress and cracking in cementitious composites: the influence of internal and external restraint. Proceedings of 4th International Research Seminar Self-Desiccation and Its Importance in Concrete Technology in Gaithersburg (Maryland), 1–20. Maruyama, I., Matsushita, T. & Noguchi, T. (2007). Numerical modeling of Portland cement hydration based on particle kinetic model and multi-component concept. Proceedings of 12th International Congress on the Chemistry of Cement in Montreal, TH1-08.3, 12 pp. Neff, P. (2008). Remarks on invariant modelling in finite strain gradient plasticity. Technische Mechanik, Band 28, Heft 1, 13-21. Nguetseng, G. (2003-4). Homogenization structures ans applications. Zeitschrift fur ¨ Analysis und ihre Anwendungen, Vol. 22, 73-107 (Part I), and Vol. 23, 482-508 (Part II). Pichler, Ch., Lackner, R. & Mang, H. A. (2007). A multiscale micromechanics model for the autogenous-shrinkage deformation of early-age cement-based materials. Engineering Fracture Mechanics, Vol. 74, 34-58. Sanavia, L. (2001). A formulation for an unsaturated porous medium undergoing large inelastic strains. In: Erwin Stein Award ’2001, International Center for Computational Engineering Sciences (Universit¨at Hannover), 42 pp. Sanavia, L., Schrefler, B. A. & Steinmann, P. (2002). A formulation for an unsaturated porous medium undergoing large inelastic strains, Computational Mechanics, Vol. 28, 137-151. Steinhauser, M. O. (2008). Computational Multiscale Modelling of Fluids and Solids – Theory and Applications. Springer, Berlin. Sˇ ˇtastn´ık, S. (2007). On the surface degradation of building claddings caused by thermal radiation. WTA Journal, Vol. 2007, 223-238. Tomosawa, F. Development of a kinetic model for hydration of cement. Proceedings of 10th International Congress on the Chemistry of Cement in Gothenburg, 2-51. Vala, J. (2006). Two-scale finite element techniques in engineering mechanics. Journal of Mechanical Engineering, Vol. 57, 127-140. Vala, J. & Sˇ ˇtastn´ık, S. (2004). On the thermal stability in dwelling structures. Building Research Journal, Vol. 52, 31-56. Vala, J., Sˇ ˇtastn´ık, S. & Koz´ak, V. (2009). Computational thermomechanical modelling of early-age silicate composites. Proceedings of the International Conference on Numerical Analysis and Applied Mathematics in Rethymno, Part I, 232-235. Yavari, A. & Marsden, J. E. (2009). Covariant balance laws in continua with microstructure. Mathematical Physics, Vol. 63, 1-42.
4 Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection Konstantin Kostarev1, Andrew Shmyrov1, Andrew Zuev1 and Antonio Viviani2 1Institute
of Continuous Media Mechanics, 2Seconda Università di Napoli 1Russia, 2Italy
1. Introduction To day, investigation of mass transfer between a drop and a surrounding medium is one of the most promising and at the same time the most complicated fields of research. The relevance of these investigations should be attributed to the fact that drops participate in many technological processes including extraction, mixing, dissolution, etc. The complexity of studies is caused by small dimensions and spherical shape of the drops which severely restricts the possibilities of experimental investigation (Henschke & Pfennig , 1999; Agble & Mendes-Tatsis, 2000; Kosvintsev & Reshetnikov, 2001; Amar et al., 2005; Waheed et al, 2002). As a result the majority of studies into the process of mass transfer between a drop and an ambient fluid cover theoretical aspects of the problem and are based on different simplifications and assumptions on the character and the level of interaction between mass transfer mechanisms (Myshkis. et al, 1987; Subramanian et al., 2001; Bratukhin et al., 2001). Therefore the results of these studies require experimental verification especially in the case of surfactant diffusion, which can locally change the surface tension at the interface and initiate the solutocapillary motion even in initially homogeneous solutions (Wegener et al., 2007, 2009a, 2009b; Burghoff & Kenig, 2006). The character of interaction between buoyancy and capillary convections generally strongly depends on the gravity level. At most times it is suggested that the buoyancy plays the main role under normal gravity and that the capillary forces dominate in microgravity conditions. However at normal gravity conditions the free convection motion provides conditions for recovering the percentage composition of the liquid mixtures near the interface. With reduction in the gravity level the outflow of both the diffusing component and depleted mixture decreases. Lowering of the concentration gradient normal to the interface reduces the probability of formation of the concentration inhomogeneities along this boundary. Therefore the possibility for the occurrence of solutocapillary motion during mass transfer processes under microgravity conditions is still an open question. In the autumn of 2007 the space experiment "Diffusion of a surfactant from a drop" was carried out during the orbital flight of the spacecraft Foton-M3 (Kostarev et al., 2010). The performed experiment was aimed at studying the development of the capillary convection
68
Mass Transfer in Multiphase Systems and its Applications
during surfactant diffusion. In the framework of terrestrial simulation of the next space experiment we carried out a series of laboratory tests to provide insight into the nature of surfactant transfer from the liquid to the drop in a thin horizontal layer. The main results of our space and terrestrial investigations of mass transfer between a drop and a surrounding medium are presented below.
2. Experimental apparatus and technique In terrestrial simulation of microgravity conditions the use of the horizontal liquid layer of small thickness gave us twofold benefits. First, it allowed a maximum reduction of intensity of the gravitational flow and second it allowed us to use a specific experimental technique – generation of a drop in the form of a short and wide vertical cylinder. The drop is bounded at the top and the bottom by the solid surfaces and has a free lateral surface which offers new possibilities for visualization of the surfactant distribution inside and outside the drop by means of optical methods. During laboratory experiments we investigated diffusion of isopropyl alcohol (used as a surfactant) from the drop of its mixture with chlorobenzene to the surrounding water (section 3, dissolving drop) or contrariwise from its ambient aqueous solution to the drop of chlorobenzene (section 5, absorbing drop). The isopropyl alcohol is lighter than water, which, in turn, has a lower density than chlorobenzene. All fluids and their solutions used in tests were transparent. The isopropyl alcohol is well soluble both in water and chlorobenzene, although the magnitudes of its solubility in these fluids differ essentially. In particular, an equilibrium distribution of alcohol between the solution and the drop is reached when its concentration in water С0 and chlorobenzene Cd is 10% and 1.2%, respectively (Fig. 1). The limiting solubility of pure chlorobenzene in water is as low as 0.05% at 30ºC and that of water in chlorobenzene is even lower. However, the reciprocal solubility of these two fluids increases with a growth of alcohol concentration in both fluids. Therefore, at low surfactant concentrations the absorbing drop during mass transfer adds only one component of the mixture – alcohol, whereas at high concentrations we might expect generation of appreciable counter-flows of the base fluids. Visualization of the surfactant distribution was made with the help of the Fizeau interferometer (Gustafson et al., 1968; Kostarev & Pshenichnikov, 2004). In accordance with the goals of experiment the interferometer was subjected to modernization, which consisted in creation of an additional unit including mirror 9 tilted at an angle of 45о to the laser beam axis, cuvette with a horizontal fluid layer 6 and video camera 8 to record the transmittedlight image of the drop (Fig. 2). The axis of rotation of the unit coincided with the optical axis of the parallel beam formed by collimator 5 of the interferometer. The center of the mirror and the beam axis also coincided in such a way that the laser beam was perpendicular to the plane layer containing the drop at any orientation of the cuvette with respect to the vector of the gravitational force. The selected scheme of the experimental setup enabled us to control the intensity of the gravitational action by way of changing the angle of inclination of the plane layer. However it also required an additional adjustment for horizontal positioning of the layer achieved with the error of less than 30′′. The interferometer cell in the form of rectangular parallelepiped 1.2 mm thick, 90 mm length and 50 mm width was used to create an element of an infinite thin horizontal layer. The surfactant distribution in the liquid layer inside the cell was visualized on its wide side. In the isothermal case the results of visualization of the concentration inhomogeneities in the fluid solutions were obtained as a system of interference bands, representing isolines of equal optical path length. In case of the mixture composition varies only across the
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
69
transmitted light beam the interference bands could be identified with certain values of the surfactant concentration. Thus, for the layer 1.2 mm thick a transition from one band to another corresponded to a variation in the alcohol content in water from 0.27% at С0 = 5% to 0.81% at С0 = 45% (Zuev & Kostarev, 2006). For the chlorobenzene mixture a similar transition occurred due to a change in the alcohol concentration by 0.10%. The initial diameter D0 of the cylindrical drops injected into the liquid layer with a medical syringe varied from 3 to 9 mm. The ambient temperature of experiments was (23±1)°С.
Cd, %
16
8
0 0
15
30
45
C0, % Fig. 1. Equilibrium concentration of isopropyl alcohol in the drop versus its concentration in the surrounding solution
I
II
Fig. 2. Schematics of the experimental setup: 1 — laser; 2 — rotating mirror; 3 — micro-lens; 4 — semi-transparent mirror; 5 — lens-collimator; 6 — plane layer with a drop; 7 and 8 — video cameras, 9 — tilting mirror
3. Surfactant diffusion from drop (terrestrial simulation) For investigation of surfactant dissolution process we used the chlorobenzene drops with he initial mass concentration of the isopropyl alcohol Cd ranged from 1% to 20%. A typical
70
Mass Transfer in Multiphase Systems and its Applications
series of interferograms of the concentration field generated around a dissolving drop of the mixture containing surfactant is shown in Fig. 3. It is seen that the process of surfactant diffusion begins concurrently with the formation of the drop (Fig. 3,a) and even earlier and has three-dimensional character despite a small thickness of the layer and its horizontal position. The alcohol, escaping from the drop, did not have time to mix with water due to a low diffusion and therefore it floated up forming a thin layer along the upper boundary of the cell. A similar situation could be observed inside the drop — chlorobenzene, which had already got rid of the alcohol, sank along the lateral walls of the drop and moved along the bottom towards its center. As a result, vertical gradients of the surfactant concentration were formed both in the drop and in the layer. Capillary convection occurred practically immediately after formation of the drop. It developed in the form of three-dimensional nonstationary cells symmetrically formed at both sides of the interface. In a short time the size of the cells became comparable with the drop radius, which provided conditions for a rapid decrease of the surfactant concentration due to a continuing transfer of the mixture from the central region of the drop to the interface. Note that the capillary flow had a rather weak effect on the gravitational flow responsible for the propagation of the concentration front in a direction away from the drop boundary (such level of the interaction manifests itself in a dramatic distinction between two types of the convective motion shown in Fig. 3,b). At the same time, the boundary of the concentration front had still the traces of the originating cell flow (Figs. 3,b–3,d). A decrease of the surfactant content in the drop smoothed down the concentration differences at the interface and the capillary flow decayed. After this the evolution of the concentration field was governed solely by the buoyancy force, which essentially simplified its structure (Fig. 3,c). As long as the amount of surfactant in the drop remained rather high, regeneration of the vertical solutal stratification at the interface led again to the development of the intensive capillary convection (Fig. 3,d). However, the arising cell motion continued for no more than a few seconds and was followed by the gravitational flow with essentially lower characteristic velocities. Depending on the initial surfactant concentration the number of such "outbursts" of the capillary convection could vary in the range from one or two at Сd = 5% to eight at Сd = 20% (it is to be noted that the number of outbursts markedly varied from test to test at the same value of Сd). The period of the alternation of different convective flow patterns was rather short (it lasted approximately two minutes at Сd = 20% for a drop with D0 = 5.6 mm). Completion of the surfactant dissolution from the drop proceeded under conditions of quasi-diffusion. Depending on the values of Сd and D0 the time of full dissolution varied from 7 to 10 minutes, which was tens times shorter than the characteristic times of diffusion. At described series of interferograms the transmitted beam passed through the optical medium, whose properties were changing along direction of the light propagation. This rendered the interpretation of the current interference pattern impossible (because in the considered situation it was the main source of information concerning the two unknown quantities — the amount and extent of the concentration inhomogeneity). On the other hand, the visualized distribution of the isolines of equal optical path length was formed by the field of surfactant concentration which enabled us to watch its propagation throughout the cell volume, to estimate the intensity of its variation using the rate of change of the interference bands at the selected points (e.g. in drop center) and also to define the characteristic times of the main stages of the dissolution process (Kostarev et al., 2007).
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
71
a)
d)
b)
e)
c)
f)
Fig. 3. Distribution of concentration during dissolution of the alcohol from the drop. D0 = 4.7 mm with Сd = 15% in a horizontal layer 1.2 mm thick. t, sec: 1 (а), 7 (b), 13 (c), 15 (d), 49 (e), 580 (f) In view of the fact that on the interferogram a transition from one interference band to another cannot be correlated with a certain variation of the concentration value, the relationships describing evolution of the concentration field will be presented without revaluation, i.e. as time variation of the number of interference bands N at the selected points. However we propose to retain the term "distribution of concentration" for discussion of the visualization results bearing yet in mind that the field structure is three-dimensional.
72
Mass Transfer in Multiphase Systems and its Applications
40 1 2 3
20 N
4
0 0
200
400
600
t, sec Fig. 4. Time variation of surfactant concentration in center of a drops with diameter of D0 = 5.0 mm at different initial surfactant concentrations: Сd, %: 10 (1); 15 (2); 20 (3)
60
1 2
30 N
3
0 0
200
400
600
t, sec Fig. 5. Time variation of concentration of surfactant for drops at Сd = 15% with different initial diameters D0, mm: 4.2 (1); 6.2 (2); 8.8 (3) As it is evident from the presented interferograms, the process of surfactant dissolution from the drop proceeds in a quite symmetrical manner, suggesting that at the center of the drop concentration of the surfactant is kept maximal. Fig. 4 shows its variation with time for drops having close diameters but different initial surfactant concentration. It is readily seen that over the selected range of Сd the obtained curves coincide. Since observation of the drop has been made up to the moment of complete surfactant dissolution, such behavior of the curves means that by the time of first measurements, coinciding with the time of cessation of the intensive Marangoni convection (see Fig. 3,c), the content of the surfactant at the center
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
73
of the drops with different Сd reaches the same value. From this observation follows the conclusion that a reduction of the difference in the initial surfactant content between different drops (even by two times) occurs at the stage of their formation and development of intensive capillary motion, i.e. during the first 10–12 seconds elapsed after the start of surfactant dissolution. As we know now, in a horizontal layer, over a rather wide range of Сd variation of surfactant concentration in the drops is described by the same relationship, no matter how many "outbursts" of capillary convection interrupting the gravitational mode of dissolution have occurred. Therefore it is of interest to us to investigate variation of surfactant concentration at the center for drops with different initial diameters (Fig. 5). As might be expected the time of complete withdrawal of the surfactant increases with the size of the drop.
r, mm
20
10
1
2
3
4
5
6
7
0 0
200
400
600
t, sec Fig. 6. Time variation of concentration front position for drops with different initial surfactant concentrations: C0, %: 1 (1), 3 (2), 5 (3), 10 (4), 15 (5), 20 (6), 30 (7) The experiments made have revealed also some specific features of the dissolution process for drops with a low content of the surfactant. Among these is the non-linear dependence of the diffusion front velocity on the surfactant concentration (curves 2 and 3 in Fig. 6). It has been found that intensification of the dissolution is caused by the oscillations of the free surface of a quiescent drop, which occurs due to a periodic onset of the local capillary convection at low alcohol concentrations (Сd ~ 3-5%). Further increase in the initial surfactant concentration results in cessation of the surface oscillations (by this time the Marangoni convection spreads over the whole surface of the drop), which reduces the rate of dissolution (at Сd from 7 to 11%, curve 4). It should be noted that similar periodic ejections of the surfactant from the interface at small values of Сd can be observed in the case of free (spherical) drops of a binary mixture which dissolves in hydroweightlessness conditions (Plateau technique). They occur as weak vertical oscillations of the drop or as periodic up-and-down motions of the emulsion over the drop surface (at Сd ~1%) (Kostarev, 2005).
74
Mass Transfer in Multiphase Systems and its Applications
a)
d)
b)
e)
c)
f)
Fig. 7. Distribution of concentration during dissolution of the alcohol from the drop D0 = 5.1 mm with Сd = 10% in the inclined layer, 1.2mm thick. Angle of inclination α = 9°. t, sec: 1 (а), 4 (b), 15 (c), 35 (d), 62 (e), 111 (f) Since our interest in dissolution of a drop in a thin horizontal layer is primarily dictated by the prospects for simulation of the diffusion processes in liquid systems with non-uniform distribution of surfactants in microgravity, it seems reasonable to give special attention to a change in the structure of the concentration field in a slightly inclined layer. Shown in Fig. 7 are the series of interferograms of the concentration field generated during surfactant dissolution from the drop in the layer inclined at an angle α = 9°. As in the case of a horizontal layer, the diffusion of the surfactant began already in the course of drop formation (Figs. 7,a–7,b) and the alcohol escaping from the drop spread chiefly in the direction of layer rising (Fig. 7,c). The concentration field inside the drop also
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
75
underwent rearrangement — the zone of maximum surfactant concentration shifted and ceased to coincide with the geometrical center of the drop (Fig. 7,d). Although the capillary convection is formally independent of the direction and the magnitude of gravitational force, nonetheless the latter has indirect effect on the process. An "outburst" of the Marangoni convection began at the upper part of the drop, accumulating alcohol, which had already permeated through the drop surface but had not left it yet (Fig. 7,e). Thereafter the wave of the capillary motion began to spread downward along the interface. As in the previous case, the process of dissolution ceased in a quasi-diffusion mode, during which the center of the concentration field remained shifted relative the drop center (Fig 7,f). The tests demonstrated that despite the rearrangement of the concentration field the intensity of mass transfer from the drop does not change with increasing α (at least up to α ~ 12°). Evidently this is because the change in the concentration field is nothing but its displacement as a whole with respect to the drop center at a distance proportional to the angle of inclination (Fig. 8). In this case, a decrease in the total flux of the surfactant from the lower part of the drop into the surrounding medium is compensated by an increase of the flux from the upper part.
Z, mm
1.4
0.7
0 0
5
10
15
α, sec Fig. 8. Displacement of the concentration field center in the drop relative its center during surfactant dissolution in the inclined layer. D0 ~ 5.0 mm; Сd = 10%
4. Surfactant diffusion from drop (space experiment) 4.1 Experimental setup To obtain the drop in microgravity conditions we used a mixture containing 85% (by mass) of chlorobenzene and 15% of isopropyl alcohol. The distilled water was used as a fluid surrounding the drop. To prevent air bubble formation during long-time storage in microgravity conditions the water and the binary mixture before pouring into the cuvette were degassed by heating them for a long time up to the boiling point. For our experiment we designed and manufactured a small-scale Fizeau interferometer (Fig. 9) (Kostarev et al., 2007).
76
Mass Transfer in Multiphase Systems and its Applications
3
7
4
5
6
2 1 8
27 cm Fig. 9. Scheme of the setup for studying heat/mass transfer processes in microgravity conditions: 1 — laser; 2 —micro-lens; 3 — semi-transparent mirror; 4 — lens-collimator; 5—Hele-Show cell with a drop; 6 and 7 — video cameras, 8 – device for drop formation The collimator block of the interferometer consisting of microlens 2, semitransparent mirror 3, and lens-collimator 4 generated a plane-parallel coherent light beam of diameter 38 mm, emerging from a semiconductor laser 1. The interferometer was equipped with two analog video cameras 6 and 7, operating respectively with the reflected beam and the beam transmitted through the cuvette 5. Camera 6 registered the interferograms of the temperature and concentration fields in the whole volume of the cuvette and camera 7 was intended to make more detailed records of the process evolution in the central part of the cuvette. The frequency of both cameras was 25 frames a second and the resolving power was 540×720 lines. For experimental cuvette we chose the Hele-Shaw cell, which was a thin gap 1.2 mm thick between two plane-parallel glass plates l with semitransparent mirror coating (Fig. 10). The cell was encased in a metal frame 2 and formed a working cell of the interferometer adjusted to a band of the infinite width. The insert 3 placed in the gap had a hollow, which was used as a cuvette working cavity 35 mm in diameter. The cavity was filled with a base fluid through the opening 4 which was then used to locate a thermal expansion compensator 5. A drop of a binary mixture was formed with the help of a needle of medical syringe which was placed along the cavity diameter. The needle was connected to the binary mixture supply system, which included a bellows for a liquid mixture, multi-step engine with a cam gear, and a device for needle decompression. The backbone of this device is a movable bar connected by means of inextensible thread to a cam mechanism. Prior to experiment the bar was inserted in the needle and the gap between them was sealed. After voltage was applied to the engine the cam began to rotate and first removed the bar from the needle and then bore against the wall of the bellows. As a result, the channel of the needle turned to be open to a flow of the binary mixture from the bellows to the cuvette cavity, where it wetted the
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
77
side glass walls and formed a cylindrical drop of prescribed volume at the center of the cuvette. After this the engine was automatically stopped.
Fig. 10. Scheme of Hele-Show cell for studying mass transfer processes: 1 — interferometric glasses, 2 — metal frame, 3 — plastic insert, 4 — opening, 5 — thermal expansion compensator, 6 — tube for drop formation To determine the flow structure formed during experiment we used the ability of the composed liquid system to form a non-transparent emulsion of water in chlorobenzene and emulsion of chlorobenzene in water while the alcohol diffused through the interface. Focusing the camera 7 (see Fig. 9) on the mid-plane of the cuvette turned the drops of emulsion into analogues of small light – scattering particles which provided flow visualization inside and outside the drop on the background of interferogram of the concentration field. The total time of the test was 52 minutes. The experiment was carried out at ambient temperature (20±1)°С. 4.2 Results The analysis of video records showed perfect consistency between the performed experiment and its cyclogram. As the experimental program envisaged during first five minutes records of the interefernce patterns were made by video camera shooting the central part of the cuvette. The absence of the alcohol distribution near the end of the syringe needle suggested that its hermetic sealing was kept up to the beginning of the experiment. There were no air bubbles on the video records made by the camera, and neither there were the intereference bands on the periphery of the images which could be indicative of non-uniform heating of the cuvette. After switching on the multi-step engine the needle is unsealed so that the binary mixture can be readily supplied to water filling the cuvette. It is to be noted that at first a rather large volume of aqueous solution of the alcohol (up to 6.5 μl ) is ejected from the needle (Fig. 11,a) and only after this the needle forms a drop of a binary mixture with a clear-cut interphase
78
Mass Transfer in Multiphase Systems and its Applications
boundary (Fig. 11,b). The maximal concentration of the alcohol in this drop is about 5.5%. The reason for appearance of the aqueous solution of the alcohol in the needle is penetration of water from the cavity into the channel of the needle after removal of the sealing bar.
a)
d)
b)
e)
c)
f)
Fig. 11. Evolution of the concentration field and flow structure during the drop formation. External diameter of needle is 1.0 mm. Time from the test outset t, sec: 4.5 (a), 4.9 (b), 5.1 (c), 8.2 (d), 8.6 (e), 10.2 (f) Since ejection of the drop is precede by appearance of the alcohol solution the drop during first seconds of its existence is in a quiescent state being surrounded by a similar media. Then as the drop grows it comes into contact with pure water which leads to initiation of intensive solutocapillary motion of the drop surface due to generation of the surface tension difference. As a result, the drop executes several oscillatory motions with large amplitude (Fig. 11,c) like a drop in the known Lewis and Pratt experiment (Lewis & Pratt, 1953). The oscillations of the drop extend the boundaries of the region containing liquid enriched with
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
79
the alcohol. This leads to a decrease of the concentration gradient at the interface and the growing drop again quiets down. Approximately at the same time the drop reaches the lateral boundaries of the cavity gradually changing its shape from a spherical to a cylindrical. As the drop turns into a cylindrical drop its internal structure becomes more and more observable. Further increase of the drop size is accompanied by formation of several internal solutal zones in the vicinity of its boundary. In these zones transfer of the surfactant occurs with quasi- diffusional velocities (the flow of the mixture caused by injection of the solution into the drop is concentrated in its central part, Fig. 11,d). A jump-wise increase of the feeding velocity by 2 times (at t = 8.3 sec) causes an abrupt intensification of the motion inside the drop, which breaks down the established concentration field. Again the vortex flow spreads over the whole drop while pure water reaches the surface of the drop in the zone of its contact with needle. This leads to a repeated outburst of capillary convection (Fig. 11,e) Development of the Marangoni convection is accompanied by deformation of the drop itself and the surrounding front of surfactant concentration, which gains a quasi-periodic structure. Then, as in the first case, a flow of the diffused surfactant into the zone, where pure water comes into contact with the solution of the drop, causes retardation of the capillary motion, which coincides in time with cessation of mixture supply to the drop (Fig. 11,f). At this moment the maximal diameter d0 of drop reaches 6.2 mm. When the forced motion in the drop ceases, the water emulsion, captured during surfactant diffusion at the time of intensive convection and kept near the drop surface, begins to penetrate deep into the drop. The penetrating emulsion forms a clearly delineated layer (Fig. 12,a). In the gap between this layer and the drop surface one can watch the formation of a light layer of the mixture, which has lost most of the surfactant due to diffusion (a decrease in the surfactant concentration leads to an abrupt change in the index of light refraction, Fig. 12,b). Propagation of emulsion with velocities of about 0.2 mm/sec is supported by a slow large-scale motion of the mixture in the drop caused by capillary eddies formed near the needle (Fig. 12,c). The source of eddy formation is the alcohol, which diffuses from the needle after cessation of mixture supply. It creates a surfactant concentration difference at the free surfaces of the air bubbles, generated near the needle due to a decrease of air solubility in the fluid of the drop, in which alcohol concentration decreases. Most of the bubbles are formed at the drop boundary and then migrate deeper and deeper into the drop under the action of capillary forces. The average diameter of the bubble is of order 0.1 mm, and the maximum diameter is ~ 0.3 mm. Apart from the eddy flow there is a slow capillary motion of the mixture over the drop surface toward its far pole (opposite to the tip of the needle). This flow also contributes to the emulsion motion. The motion of emulsion is accompanied by coalescence of part of its droplets, which settle down on the walls of the cavity. (The arising droplets can be seen due to a trace of emulsion kept in the stagnation zone behind them, Fig. 12,d). As the emulsion layer moves away from the boundary, one can observe development of a small-cell motion near the bubbles, which are in the diffusion gradient of the surfactant at the drop boundary. What is interesting, detachment of these bubbles from the drop interface as well as the local displacement of the drop boundary due to reduction of its area during diffusion of the surfactant causes a specific stochastic fluttering of the drop surface.
80
Mass Transfer in Multiphase Systems and its Applications
a)
d)
b)
e)
c)
f)
Fig. 12. Evolution of the concentration field and flow structure during surfactant dissolution process. Time from the test outset t, sec: 15.5 (a), 38.7 (b,) 88.4 (c), 163 (d), 251 (e), 273 (f) The cell motion reaches maximum intensity at the drop pole opposite to the tip of the needle (evidently due to the absence of flows generated earlier in this region). The air bubbles formed in the immediate neighborhood, accelerates the motion of mixture from the center of the drop and also favors the development of the cell motion. The arising flow is of threedimensional pattern and as the times goes it occupies an increasingly growing space and even deforms the solutal front, which moves away from the drop (Fig. 12,e). Simultaneously there occurs another interesting phenomenon – settling of gas bubbles at the cavity walls. During sedimentation the bubbles take the form of irregular semi-spheres. This effect can be observed at the time when the bubbles are in the emulsion cloud. After five minutes from the beginning of drop formation the velocity of the fluid flow in the drop decreases practically to zero (Fig. 12,f) and the volume of the drop reduces to 0.9 of its maximum (Fig. 13).
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
81
V/Vmax
1.0
0.5
0.0 1
10
100
1000
10000
t, sec Fig. 13. Variation of the relative volume of dissolving drop with time Fig. 14 shows a series of interferograms of the concentration field in the vicinity and inside the drop at different moments of time. As it is seen from the figure, in the following, after first five minutes, the only observable events are gradual dissolution of the emulsion and variation of the surfactant concentration gradient in the radial direction. Apart from this a decrease of the alcohol concentration in the region near the drop boundary leads to a growth of the surface tension and, as a result, to local jump-wise displacement of the drop boundary while the area of the latter decreases. Hence, based on the analysis of the obtained video records we can draw a conclusion that during diffusion of the surfactant from the drop at least three times there were favorable conditions for the development of the intensive Marangoni convection. However, all the observed capillary flows rapidly decayed. In the first two cases – during drop formation and a change in the mixture feeding regime – the Marangoni convection decay was provoked by a flow of a surrounding fluid with higher surfactant concentration into the zone of the capillary motion, which eliminates the concentration difference along the interface. On the other hand, generation of such surfactant distribution in the vicinity of the drop was made possible only in the absence of the Archimedean force with the result that molecular diffusion became a governing factor in the process of mass transfer outside the drop. In the third case, when the Marangoni convection was initiated near the gas bubbles inside the drop, the reason of its decay was a decrease of surfactant percentage in the mixture filling the needle channel and rapid recovery of the surfactant distribution homogeneity in the region near the bubbles due to convective mixing. Video recording of the central part of the cuvette has made it possible to trace the evolution of initiated flows, whereas records of the general view of the drop (Fig. 15,a) allow us to investigate propagation of the concentration front from the dissolving drop of the binary mixture and to establish the relationship between the position of its boundary and time (Fig. 15,b). It is readily seen that propagation of the concentration front is described fairly
82
Mass Transfer in Multiphase Systems and its Applications
well by the power law with the exponent 1/3. Over the whole period of the experiment position of the concentration front changed by 5 mm suggesting that propagation of the surfactant occurred with diffusion velocities. According to measurements made in the second half of the experiment, the concentration filed has no preferential direction of propagation, which allows us to suppose that the value of the residual accelerations on the satellite "Foton-M 3" during the experiment was no higher than 10-4 go.
a)
b)
c)
Fig. 14. Evolution of the concentration field and flow structure during surfactant dissolution process. Time from the test outset t, min: 15.2 (a), 19.3 (b), 28.8 (c)
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
83
b)
a)
6
R, mm
3
0 0
1000
2000
3000
t, sec Fig. 15. View of distribution of surfactant concentration around drop (a) and variation of the boundary position (b) of concentration field with time A detailed structure of the concentration field generated by surfactant diffusion (Fig. 16) was defined by making use of the computer–aided overlapping of images obtained from both video cameras (such an approach was used to solve the problem with relatively low value of their resolving power). Since only one video recorder was used for recording, we chose for overlapping the images shot by different camera with the shortest time span between them. It should be emphasized that distribution of the surfactant concentration outside the drop was obtained by way of direct measurements, which were made based on the interferograms starting from the field (front) boundary. It was impossible to apply this approach inside the drop because of the unknown value of the surfactant concentration at the drop boundary. This value remained unknown due its jump-wise change provoked by a difference in the chemical potentials. We determined it from the curves, which were plotted based on the coefficient of the equilibrium distribution of the isopropyl alcohol in the chlorobenze-water system under the assumption that the dissolution process was quasiequilibrium due to predominance of diffusion. For the selected system of fluids the value of this coefficient was 0.12 in 15% water solution of the alcohol and as the alcohol concentration decreased, this coefficient also decreased to 0.10. As it follows from Fig. 17, alcohol concentration at the drop surface at the time when the motion of the mixture in the drop ceases, is ~ 14%, which actually coincides with the initial concentration of the alcohol in the binary mixture of the drop. Note that at the end of the test the surfactant concentration at the drop boundary decreased approximately by two times. This reduction can be approximated with the least error by the exponential relationship. For the sake of comparison, on the Earth under conditions of maximum suppression of the gravitational convection the drop of the same volume completely lost the alcohol in a matter of ten minutes.
84
Mass Transfer in Multiphase Systems and its Applications
15 1 2
10 C, %
3 4
5
5
0 0
d0 3
6
9
r, mm Fig. 16. Radial distributions of surfactant concentration in the vicinity and inside the drop at various time moments. t, min: 4.9 (1), 21.3 (2), 31.0 (3), 42.5 (4), 50.7 (5)
15
C, %
10
5
0 0
1200
2400
3600
t, sec Fig. 17. Variation of surfactant concentration in water near the drop surface with time
5. Drop saturation by surfactant from homogeneous solution In this series of test the initial mass concentration С0 of the alcohol in the solution ranged from 1% to 50%. Fig. 18 shows two series of the interferograms reflecting the evolution of the alcohol distribution in the drop at different initial concentrations of alcohol in the solution. It is seen that at С0 ≤ 10% absorption of alcohol occurs without the development of the capillary convection in spite of the interference of the gravity force, which generates the vertical concentration gradient and, accordingly, the gradient of the surface tension. The
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
85
latter seemed to be not large enough to produce shear stresses capable of deforming the adsorbed layer, which was formed at the interface from the impurities found in water (Birikh et al., 2009). In the absence of the Marangoni convection, alcohol was slowly accumulated at the upper part of the drop. As soon as an increasingly growing thickness of the alcohol layer caused an additional optical beam path difference of half of the light wave length, the color of the drop on the interferogram changed (Figs. 18,b-18,c).
a)
d)
b)
e)
c)
f)
Fig. 18. Saturation of the chlorobenzene drop with isopropyl alcohol from its solution filling a horizontal Hele-Shaw cell. С0 = 10%, D0 = 5.2 mm; t, min: 0.5 (a), 7.0 (b), 10.0 (с); С0 = 20%, D0 = 5.4 mm; t, min: 0.1 (d), 1.0 (e), 6.0 (f) At С0 ~ 20% the gradients of surfactant concentration become higher than the threshold values which results in the development of a fine-cell capillary motion at the drop surface. With the growth of surfactant concentration the velocity of the surfactant flow into the drop increases and the gravitational force has not managed to smooth the layer of alcohol along the drop diameter. Due to the fact that the layer is formed from alcohol, rising along the lateral surface of the drop, its thickness is found to be larger at the layer edges. On the
86
Mass Transfer in Multiphase Systems and its Applications
interferograms the radial variation in the layer thickness is represented by a system of concentric isolines, which merge with the passage of time at the center of the drop (Figs. 18,d -18,e). On the drop periphery one can readily see a thin layer of rising alcohol, which has diffused through the interface (Fig. 18,f).
1.0
N/N0
1
0.5
2 3
0.0 0
20
40
60
t, min Fig. 19. The relative number of isolines inside the drop as a function of time for different concentrations of solution С0, %: 10 (1), 20 (2), 30 (3). The initial drop area S0 ∼ 35 mm2 In Fig. 19, a relative number of the interference bands vanishing at the center of the drop is plotted versus the time elapsed from the moment of drop formation for solutions of different concentrations (for normalization we used the maximum number of the bands obtained in each cases). The analysis of the curve behavior shows that duration of the phase, in which a convective mass transfer dominates over a pure diffusion transfer, rapidly increases with the growth of surfactant concentration in the solution. Absorption of alcohol from its solution should cause a growth of the drop volume, which in the case of the cylindrical drop with the fixed thickness is manifested as an increase of its area. Indeed, saturation of the drop with alcohol was accompanied by a change of its area. However, this variation was of a complicated nature, which was specified by the initial concentration of the surfactant in the solution (Fig. 20). Such a behavior of the absorbing drop can be explained by an increase in the reciprocal solubility of water and chlorobenzene with a growth of concentration of their common solvent, viz., the content of alcohol in their solutions. The maximum increase (~20%) in the drop area was observed at the initial stage of its saturation at С0 = 40% (curve 3 in Fig. 20). Then the drop began to dissolve due to increasing diffusion of chlorobenzene in the surrounding solution. A delay in dissolution was caused by the insufficient content of the surfactant inside the drop. The desired concentration was achieved only some time after injection of the drop into the solution. In the solution containing 45% of alcohol (curve 4 in Fig. 20) concentration of the absorbed surfactant at the drop boundary immediately reached the value, at which chlorobenzene began to dissolve in the surrounding solution. The process of the surfactant extraction turned into the reverse – dissolution of the extragent.
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
87
S/S0
1.6
0.8
ΔС, % 1
3
2
4
0.0 0
20
40
60
t, min Fig. 20. The relative area of the chlorobenzene drop as a function of time for isopropyl solutions of various concentrations. The initial drop area S0 ∼ 35 mm2. С0, %: 10 (1), 30 (2), 40 (3), 45 (4) Dissolution of chlorobenzene gave rise to an intensive gravitational flow in the surrounding solution. This process every so often was accompanied by generation of both the vertical and longitudinal (lying in the layer plane) difference of the surfactant concentration at the drop surface provoking the development of a large-scale capillary flow. In our case, such a flow occurred in the form of two quasi-stationary vortices lying in the horizontal plane (Fig. 21). Note that the flow was sustained by a small difference (~3%) in the surfactant concentration between the "western" and "eastern" poles of the drop. The initial solution entrained by the flow reached the drop surface in the form of the concentration "tongue", which then split into the streams flowing round the drop. As they spread along the drop surface they lost part of alcohol due to its diffusion. After that they again merged into a single flux, which drifted away from the drop carrying part of alcohol– chlorobenzene mixture. In turn, alcohol penetrated into the drop and formed two fluxes, which first moved along the interface and then after collision at the western pole of the drop spread deep into the drop generating a two-vortex flow. The flows initiated inside and near the drop closely resemble in structure the convective flow near the drop absorbing the surfactant from its stratified solution in the vertical Hele-Shaw cell (Kostarev et al., 2007). However, under conditions of maximum suppression of gravitational convection the considered flow remains quasi-stationary – in contrast to the flow in a vertical cell, which at the similar surfactant concentration differences is of the pronounced oscillatory nature. At С0 = 50% the phase boundary between the drop and the solution disappears leading to the formation of a three-component liquid mixture. Phase separation of the fluid system vanishes within the first two minutes after placing the drop into the surfactant solution.
88
Mass Transfer in Multiphase Systems and its Applications
a)
b)
c)
Fig. 21. Distribution of concentration of isopropyl alcohol during its absorption by the drop of chlorobenzene from the solution with initial concentration С0 = 45%. D0 = 6.5 mm. t, min: 0 (а); 40 (b); 190 (c, general view of the cell flow with the drop in center)
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
89
a)
b)
c)
Fig. 22. Dissolution of a drop of chlorobenzene in 50% solution of alcohol. t, min: 1.25 (а); 9.0 (b); 11.2 (c) Fig. 22 illustrates the main stages of drop dissolution in the surrounding solution at С0 = 50%. Absorption of alcohol at the moment of drop formation diminishes the interface surface tension to an extent that it turns to be impossible to form a cylindrical drop even in one-millimeter clearance. Nevertheless, the original drop has an interface with sufficient curvature, owing to which the probing light beam scatters. As a result the drop interface is seen on the interferogram as a grey spot (Fig. 22,a). Then the drop surface increases because the drop spreads out over the cavity bottom as the surface tension continuously decreases. Further dissolution is accompanied by deformation of both the drop interface and the boundary between the drop and a solid substrate. Disappearance of the interface in the fluid
90
Mass Transfer in Multiphase Systems and its Applications
system makes the mixture optically transparent because the jumps of the refraction coefficient have vanished. Fig. 22,b presents the interferogram of the optical inhomogeneity caused by inhomogeneous concentration of chlorobenzene at the place of the former drop. It is seen that a transition zone between the solution and the mixture with higher content of chlorobenzene has a well-defined relief, which is similar to the relief of the free surface of the drop. In Fig. 22,с we can see part of the concentration inhomogeneity picture with typical distribution of chlorobenzene in alcohol in the form of "fingers", whose origination can be attributed to a flow of chlorobenzene down the spatial inhomogeneities of the transition zone. The period of spatial perturbations of the drop-solution interface, repeated further by the relief of the transition zone of the concentration inhomogeneity, is defined by the physicochemical properties of the interacting fluids. As for the solution, these properties are strongly dependent on surfactant concentration. Indeed, according to the results of measurement the angular distance between the "fingers" increases with a growth of the surfactant solution concentration (Fig. 23).
a, rad
0.12
0.09
0.06 39
43
47
51
C, % Fig. 23. Variation of the angle between "fingers" with the growth of initial concentration of the surfactant solution
6. Conclusion As seen from a comparison of space and terrestrial experiments, the data obtained in microgravity differ markedly from the results of the laboratory study of surfactant diffusion in a thin horizontal layer. In the later case a small coefficient of surfactant diffusion facilitated generation of the density difference in the originally homogeneous surrounding fluid. This difference was large enough for development of the gravitational motion inside and outside the drop. Nevertheless a relative contribution of the Marangoni convection to the process considerably increased — the action of the capillary forces mainly determined the rate of mass transfer at the beginning of surfactant diffusion. Only a decrease in the surfactant concentration below some critical value led to regeneration of the gravitationaldiffusion mechanism of mass transfer, yet its action was repeatedly interrupted by the
Surfactant Transfer in Multiphase Liquid Systems under Conditions of Weak Gravitational Convection
91
"outbursts" of intensive capillary convection. Because of a three-dimensional structure of the flows in the laboratory conditions, the application of the interference method posed many difficulties; only the qualitative characteristics were used for description of the evolution of concentration fields. However, the laboratory experiments allowed us to make an optimal choice of the parameters for the space experiment and to prepare its preliminary cyclogram. The space experiment "Diffusion of the surfactant from a drop" was successful. The sensitivity of the new setup proved to be an order of magnitude higher than that of the shadow device "Pion-M" used on the "Mir" space station. The weight of the setup was reduced by more than an order of magnitude, and its external dimensions were also down sized. The interferometer can operate in the automatic regime allowing performance of experiments onboard the unmanned space vehicles. The obtained data supported the view that in microgravity conditions the mass transfer processes involving surfactant diffusion through the interface can proceed without excitation of intensive capillary convection. Because of diffusion in the absence of capillary convection, the surfactant concentration reaches rather high values at both sides of the drop surface. This leads to much greater extent of mutual dissolution of the base fluids compared to the terrestrial conditions. Therefore, the interface failure in such a system can occur at much lower concentration of the surfactant which plays the role of a common solvent for both the base fluids. On the one hand, this allowed a more exact computation of the value of this concentration, which is an essential prerequisite for development of the theoretical grounds of phase transitions in three-component liquid systems. On the other hand, reduction of the limiting concentration opens the way to intensive experimental studies of the hydrodynamic effects involving the interface failure. At the same time, based on terrestrial simulation data, we can expect the development of a large-scale Marangoni flow around the drop absorbing the surfactant from the homogeneous surfactant solution in microgravity conditions. Such a different evolution of mass transfer processes in the surfactant solution emphasizes again the importance of experimental investigations in real microgravity conditions.
7. Acknowledgements The work was supported by Russian Foundation of Fundamental Research under project No 09-01-00484, joint project of SB, UB and F-EB of RAS (116/09-С-1-1005) and the program of the Department of Power Engineering, Mechanical Engineering, Mechanics and Control Processes of RAS No 09-Т-1-1005.
8. References Agble, D. & Mendes-Tatsis, M.A. (2000). The effect of surfactant on interfacial mass transfer in binary liquid-liquid systems. J. Heat and Mass Transfer, Vol. 43, p. 1025. Amar, A.; Groß-Hardt, E.; Khrapitchev, A.A.; Stapf, S.; Pfennig, A. & Blümich, B. (2005). Visualizing flow vortices inside a single levitated drop. J. of Magnetic Resonance, Vol. 177, No. 1, pp. 74–85. Bratukhin, Yu.K.; Kosvintsev, S.R. & Makarov, S.O. (2001). Droplet motion induced by diffusion of soluble surfactant to the external medium: theory. Colloid J., Vol. 63, No. 3, pp. 326–332.
92
Mass Transfer in Multiphase Systems and its Applications
Burghoff, S. & Kenig, E.Y. (2006). A CFD model for mass transfer and interfacial phenomena on single droplets. AIChE J., Vol. 52, No. 12, pp. 4071–4078. Gustafson, S.E.; Kjellander, R.A.E. & Rolf, A.E. (1968). An interferometer for direct recording of refractive index distributions. Z. Naturforch., Vol. 23a, No. 2, pp. 242–246. Henschke, M. & Pfennig, A. (1999). Mass transfer enhancement in single drop extraction experiments. AIChE J., Vol. 45, No. 10, pp. 2079–2084. Kostarev, K.G. & Pshenichnikov, A.F. (2004). Gravitational convection of a liquid mixture in a horizontal cylindrical gap at moderate Grasshoff numbers. Cosmic research, Vol. 42, No. 2, pp. 115–122. Kostarev, K.G. (2005). The study of the extraction of surface-active component of a binary liquid from model ("cylindrical") droplets. Colloid J., Vol. 67, No. 3, pp. 357–362. Kostarev, K.G.; Levtov, V.L.; Romanov, V.V.; Shmyrov, A.V.; Zuev, A.L. & Viviani, A. (2007). Experimental investigation of mass transfer in fluid systems in microgravity conditions. Proceedings of 58th Int. Astronautical Congress, Hyderabad, India, 2007. Paper № IAC-2007-A2.4.06. 10 p. Kostarev, K.G.; Levtov, V.L.; Romanov, V.V.; Shmyrov, A.V. & Viviani, A. (2010). Experimental study of surfactant transfer in fluid systems in microgravity conditions. Acta Astronautica, Vol. 66, No. 3–4, pp. 427–433. Kosvintsev, S.R. & Reshetnikov, D.G. (2001). Droplet motion induced by diffusion of soluble surfactant to the external medium: experiment. Colloid J., Vol. 63, No. 3, pp. 318– 325. Lewis, J.B. & Pratt, H.R.C. (1953). Instabilities induced by mass transfer and deformable fluid interfaces. Nature, Vol. 171, pp. 1155—1161. Myshkis, A.D.; Babskii, V.G.; Kopachevskii, N.D.; Slobozhanin, L.A. & Tyuptsov, A.D. (1987). Low-Gravity Fluid Mechanics, Springer, the Netherlands. Subramanian, R.S. & Balasubramaniam, R. (2001). The motion of bubbles and drops in reduced gravity, Cambridge University Press, Cambridge, UK. Waheed, M.; Henschke, M. & Pfennig, A. (2002). Mass transfer by free and forced convection from single spherical liquid drops. J. of Heat and Mass Transfer, Vol. 45, No. 22, pp. 4507–4514. Wegener, M.; Grunig, J.; Stuber, J. & Paschedag, A.R. (2007). Transient rise velocity and mass transfer of a single drop with interfacial instabilities – experimental investigations. Chemical Engineering Science, Vol. 62, No. 11, pp. 2967-2978. Wegener, M.; Fevre, M.; Paschedag, A.R. & Kraume, M. (2009a). Impact of Marangoni instabilities on the fluid dynamic behaviour of organic droplets. J. of Heat and Mass Transfer, Vol. 52, No. 11–12, pp. 2543–2551. Wegener, M.; Paschedag, A.R. & Kraume, M. (2009b). Mass transfer enhancement through Marangoni instabilities during single drop formation. J. of Heat and Mass Transfer, Vol. 52, No. 11–12, pp. 2673–2677. Zuev, A.L. & Kostarev, K.G. (2006). Oscillation of a convective flow round the air bubble in a vertically stratified solution of a surfactant. J. Experimental and Theoretical Physics, Vol. 130, No. 2, pp. 363–370.
5 Mass Transfer in Multiphase Mechanically Agitated Systems Anna Kiełbus-Rąpała and Joanna Karcz
West Pomeranian University of Technology, Szczecin Poland
1. Introduction In this chapter, the results of the experimental studies concerning the volumetric mass transfer coefficient kLa obtained for mechanically agitated gas – liquid and gas – solid – liquid systems are discussed. Mechanically agitated gas – liquid and gas –solid – liquid systems are widely used in many processes, for example oxidation, fermentation or wastewater treatment. In such cases, oxygen mass transfer between gas and liquid phases in the presence of solid particles can be described and analyzed by means of the volumetric mass transfer coefficient kLa. In the gas – liquid and gas – solid – liquid systems, the kLa coefficient value is affected by many factors such as geometrical parameters of the vessel, type of the impeller, operating parameters of the process (impeller speed, aeration rate), properties of the continuous phase (density, viscosity, surface tension, etc.) and also by the type, size and loading of solid particles. To improve the efficiency of the processes conducted in gas – liquid and gas – solid – liquid three – phase systems two or more impellers on the common shaft are often used (Kiełbus—Rąpała & Karcz, 2009). Multiple – impeller stirred vessels due to the advantages such as increased gas hold – up, higher residence time of gas bubbles, superior liquid flow characteristics and lower power consumption per impeller are becoming more important comparing with single – impeller systems (Gogate et al., 2000). As the number of energy dissipation points increased with an increase in the impellers number on the same shaft, there is likely to be an enhancement in the gas hold – up due to gas redistribution, which results into higher values of volumetric gas – liquid mass transfer coefficient (Gogate et al., 2000). Correct design of the vessel equipped with several agitators, therefore, the choice of the adequate configuration of the impellers for a given process depends on many parameters. That, which of the parameters will be the most important depends on the kind of process, which will be realized in the system. For the less oxygen demanding processes the designer attention is focused on the mixing intensity much more than on the volumetric mass transfer coefficient. When the most important thing is to achieve high mass transfer efficiency of the process, the agitated vessel should be such designed that the configuration of the agitators used ensure to get high both mixing intensity and the mass transfer coefficient values (Kiełbus-Rąpała & Karcz, 2010).
94
Mass Transfer in Multiphase Systems and its Applications
1.1 Survey of the results for gas-liquid system Good mass transfer performance requires large interface area between gas and liquid and a high mass transfer coefficient The obtaining the good dispersion of the gas bubbles in the liquid agitated depends on the respectively high agitator speed, therefore the characteristics of the gas-liquid flow are intensively studied (Paul et al., 2004); Harnby et al., 1997). In literature, there are a large number of correlations for the prediction of volumetric mass transfer coefficients kLa in mechanically stirred gas-liquid systems (Linek et al., 1982, 1987; Nocentini et al., 1993; Gogate & Pandit, 1999; Vasconcelos et al., 2000; Markopoulos et al., 2007). Markopoulos et al. (2007) compared the results which were obtained by other authors for agitated Newtonian and non-Newtonian aerated liquids. The comparative analysis carried out by Markopoulos et al. (2007) shows that significant disagreement is observed taking into account the form of the correlations for kLa. Therefore, no single equation exists representing all of the mass transfer data given in literature. The differences can mainly be ascribed to the differences in the geometry of the system, the range of operational conditions, capability to gas bubbles coalescence and the measurement method used. For a given geometry of the agitated vessel and liquid properties, volumetric mass transfer coefficient kLa for gas-liquid system is often described in literature by means of the following dependences kLa = f(P/VL, wog)
(1)
kLa = f(n, wog)
(2)
or
where: P/VL - specific power consumption, wog – superficial gas velocity, n – agitator speed. Most often, empirical correlations have the form of the following equations kLa = C1(PG-L/VL)a1(wog)a2
(1a)
kLa = C2(n)a3(wog)a4
(2a)
or
Detailed values of the exponents a1 and a2 in Eq. (1a) obtained by different authors are given in paper by Markopoulos et al. (2007). Recently, Pinelli (2007) has studied the role of small bubbles in gas-liquid mass transfer in agitated vessels and analyzed two-fraction model for non-coalescent or moderately viscous liquids. Martin et al. (2008) analyzed the effect of the micromixing and macromixing on the kLa values. This study shows that each mixing scale has a particular effect on the mass transfer rate. It is worth to notice that values of the kLa coefficient can be depended on the measurement method used (Kiełbus-Rąpała & Karcz, 2009). Although a number of techniques were developed to measure the kLa values, the unsteady-state gassing-out dynamic methods (Van’t Riet, 1979; Linek et al., 1982; Linek et al., 1987; Linek et al., 1996; Ozkan et al., 2000; Lu et al, 2002, Garcia-Ochoa & Gomez, 2009) are preferably used as they are fast, experimentally simple and applicable in various systems. These methods are used in many variants. For example, Machon et al. (1988) used a variation of the dynamic method in which the gas from liquid was firstly removed by vacuum and the system was then aerated
Mass Transfer in Multiphase Mechanically Agitated Systems
95
for some time. When aeration was stopped and the bubbles escaped from the liquid, the steady state concentration of dissolved oxygen was measured. Apart from experimental studies, new methods are recently used to prediction the values of the volumetric mass transfer coefficient. Lemoine & Morsi (2005) applied artificial neural network to analyze mass transfer process in a gas-liquid system. Using CFD technique, Moilanen et al. (2008) modeled mass transfer in an aerated vessel of working volume 0.2 m3 which was equipped with Rushton, Phasejet or Combijet impeller. 1.2 Survey of the results for gas-solid-liquid system The critical impeller speed for the solid suspension in liquid can be defined as the impeller speed at which no particles resting on the bottom of the vessel longer then 1- 3s (Zwietering, 1958). In multiple –impeller system introduction of gas into solid – liquid system implicate an increase in the impeller speed required for particles suspension just like in a single – impeller system. For solid suspension multiple impeller systems would prove to be disadvantageous if the distance between impellers is greater than the diameter of the impeller as there is an increase in the critical impeller speed for solid suspension (Gogate et al., 2000). The data on the multiple – impeller systems working in the three – phase gas – solid – liquid systems are limited (Kiełbus-Rąpała & Karcz, 2009). Various aspects of the three – phase system stirring in the vessel equipped with more than one impeller on the common shaft were the aim of the studies in papers (Dutta & Pangarkar, 1995; Dohi et al., 1999, 2004; Roman & Tudose, 1997; Majirowa et al, 2002; Jahoda et al., 2000; Jin & Lant, 2004). The impellers used were usually Rushton turbines or pitched blade turbine. Dutta & Pangarkar (1995) and Dohi et al. (1999) analyzed experimentally the critical impeller speed needed to gas dispersion simultaneously with solid suspension in the systems, with four and three impellers, respectively. Critical impeller speed in multiple – impeller system can be modified easily by choosing optimal impeller combination. Power consumption in multiple – impeller systems was studied by Dohi et al., 1999, 2004; Majirowa et al., 2002; Roman & Tudose, 1997. Investigations in such systems concerned also gas hold – up (Dutta & Pangarkar, 1995; Dohi et al., 1999, 2004; Majirowa et al., 2002; Jahoda et al., 2000) and mixing time (Dutta & Pangarkar, 1995; Dohi et al., 1999; Jahoda et al., 2000). Hydrodynamics problems in the system stirred by means of triple impellers were analysed by Jin & Lant (2004). Authors compared hydrodynamic conditions in the stirred vessel with the air – lift and bubble column. Although kLa coefficients were widely studied in the two – phase gas – liquid multiple – impeller systems (Arjunwadkar et. al, 1998; Fujasowa et al., 2007; Puthli et al., 2005; Moucha et al., 2003; Linek et al., 1996; Wu, 1995; Yoshida et al., 1996; Yawalkar et al., 2002) and many papers (Alper et al., 1980; Brehm et al., 1985; Lu et al., 1993; Kralj & Sinic, 1984; Chapman et al., 1983; Ruthiya et al., 2003) regard kLa measurements in the three – phase system stirred in the vessel equipped with single – impeller, the information in literature on this parameter in multi impeller gas – solid – liquid system is substantial. On the basis of the literature data, the effect of solid particles on gas – liquid oxygen mass transfer rate in single – impeller systems at low solid concentrations analyzed Kiełbus— Rąpała & Karcz (2009) and Karcz & Kiełbus—Rąpała (2006). This effect was investigated by many authors (Alper et al., 1980; Brehm et al., 1985; Oguz et al., 1987; Lu et al., 1993; Kralj &
96
Mass Transfer in Multiphase Systems and its Applications
No
Ref.
Type of solids
1.
Chandrasekaran activated carbon & Sharma, 1977 0–2 mass %
2.
Joosten et al., 1977
3.
Alper et al., 1980
4.
Lee et al., 1982
glass beads 0–50 mass %
5.
Chapmann et al., 1983
glass ballotini 3 and 20 mass %
6.
Kralj 1984
7.
Brehm 1985
&
Polypropylene, sugar, glass beads, 0–40% vol. activated carbon, quartz sand 0–2 mass %
Size of particles <100 μm
< 5 μm < 5 μm 56 μm
al., Al2O3 0–10% vol. ion exchange resin 0–40 mass % glass ballotini 0–50 mass %
50 μm, 300 μm 780 ± 70 μm
9.
Bartos & glass beads Satterfield, 1986 0–30% vol.
60 μm
10.
Mills et al., 1987
66 μm
12.
13.
Lu & Liang, kaolin 1990; cit. in Lu et 0–4 mass % al., 1993 kaolin powder Lu et al., 0–4.5% vol. 1993 yeast 0–8% vol. SchotchbriteTM pads Özbek & Gayik, pieces (biomass): 2001 5–25% vol.
increases 1.5 times Constant Constant rapidly decreases
0–0.2 mass %
increases 1.5 times
0.2–2 mass %
constant
0–30 mass %
decreases rapidly
30–50 mass %
decreases slowly slightly decreases significantly decreases
the whole range Constant
Greaves & Loh, 1985
11.
0–0.2 mass %
0–3 mass % 3–20 mass %
8.
glass beads 0–40% vol.
kLa coefficient Value
0.2–2 mass %
53-105, 250 μm 0–20% vol. 74-105 μm 53 μm, 88 μm 20–40% vol.
Sincic, activated carbon 0.25 and 0.5 mass % et
Solids concentration
0–5% vol.
increases 1.5 times
5–10% vol.
Decreases
0–15 mass %
665 μm, 1.300 15–50 mass % μm
5.7 μm 5.5 μm 3.7 μm 0.1625 cm3, 0.65 cm3, 1.4625 cm3
14.
Kiełbus & Karcz, Sea sand 2006 0.5–5 mass %
335 μm
15.
nylon 6.6, glass beads; Littlejohns & Silicone rubber, Daugulis, 2007 styrene-butadiene copolymer
2.59 mm 6 mm 2.5 mm 3.59 mm
constant decreases rapidly
decreases with the whole range concentration increasing decreases with the whole range concentration increasing decreases with the whole range concentration increasing
solid
solid
solid
increases to maximum the whole range (c.a. 2%) and then decreases decreases with the whole range concentration increasing Increases 0.5 mass % 2.5–5mass %
solid
Decreases Increases up to 268%
167g/l Reducing by up to 63%
Table 1. The effect of presence and concentration of solid particles on kLa values determined by different authors
Mass Transfer in Multiphase Mechanically Agitated Systems
97
Sinic, 1984; Chapman et al., 1983, Ozkan et al., 2000; Kordac & Linek, 2010). The results of their studies were not always similar. The effect of presence and concentration of solid particles on volumetric mass transfer coefficient kLa determined by different authors is compared in Table 1. Volumetric mass transfer coefficient value increased (Alper et al., 1980; Brehm et al., 1985; Lu et al., 1993), was constant (Kralj & Sinic, 1984) or slightly decreased (Chapman et al., 1983) with adding the particles in the system. Such differences can suggest that very important are properties of the particles, containing particle size (Ozbek & Gayik, 2001), density, hydrophobicity, oxygen diffusivity (Zhang et al., 2006; Littlejohns et al., 2007) and concentration. Various mechanisms were proposed for describing an enhancement of kLa caused by the particles. Shuttling effect, where absorptive particles enter the liquid boundary layer, absorbing dissolved gas and then desorbing this gas when back in the bulk phase. This effect is used especially for small particles with a size equal or smaller than the gas – liquid boundary layer (Ruthiya et al., 2003). For inert particles, without absorptive properties, the possible mechanisms which explain an enhancement of kla include boundary layer mixing and gas – liquid interface changing. Boundary layer mixing, involving an increase in kL due to turbulence at gas – liquid interface (Ruthiya et al., 2003; Kluytmants et al., 2003; Zhang et al., 2006), which causes a larger refreshment rate of liquid boundary layer by mixing with the bulk fluid. Changes in the gas – liquid interfacial area can be result of the particles presence at the gas – liquid interface, which can collide and interact with the gas – liquid interface or may induce turbulence near or at it, leading to a smaller effective diffusion layer or causing coalescence inhibition and an increase in a interfacial area (Ruthiya et al., 2003). However, a simple mechanism describing all cases does not exist. Comparing the data shown in Table 1 for a high concentration of the particles in the agitated three phase system it is worth to notice that values of the kLa coefficient rather decrease when the solid concentration increases (for example data given by Joosten et al., 1977; Lee et al., 1982; Brehm et al., 1985). The results of the volumetric mass transfer coefficient kLa for the agitated three phase gassolid-liquid system are usually correlated by different authors in the form of the following dependence kLa = f(P/VL, wog, …)
(3)
Some correlations presented in literature are shown in Table 2. Galaction et al. (2004) conducted the kLa coefficient measurements in the three – phase system containing various type of microorganisms. Authors studied the effect of concentration and morphology of biomass, specific power input and superficial air velocity on volumetric gas – liquid mass transfer coefficient value in the stirred vessel equipped with two turbine stirrers. They proposed the following mathematical correlation kLa = aXα(PG-L-S/VL)βwogγ
(4)
describing the influence of considered factors on kLa. The values of the parameters a, α, β and γ in Eq. (4) are given in Table 3. On the basis of the measurements authors have found that, in the bioreactor, the value of kLa depends not only on operating and geometrical parameters but also on the type and morphology of the microorganisms in the system.
98
Author
Kralj & Sincic 1984
Brehm et al. 1985
Brehm & Oguz 1988
Mass Transfer in Multiphase Systems and its Applications
Equation
⎛P ⎞ kL a = 0.109 ⎜ G − L −S ⎟ ⎝ VL ⎠
System
0.34 wog
Aqueous Rushton solution of turbine; NaOH – air – active d/D = 0.33 carbon
⎛ ηm ⎞ ⎜ ⎟ ⎝η ⎠
water or aqueous solution of polyetylen glycol – air – different solid particles
0.213
⎛P ⎞ kL a = 0.5612 ⎜ G −L −S ⎟ ⎝ VL ⎠
0.65
Impeller
0.47 0.4 wog
0.75
⎛ PG − L −S ⎞ 0.5α 0.5 ⎜ ⎟ wog DL VL ⎠ kL a = 3.07 ⋅ 10 −3 ⎝ 0.34 3
ηm σ L
water (or various organic liquids) – air – various solid particles
Turbine with 4 flat blades;
D [m]
Operating parameters n = 12.5-50 1/s;
wog = 10-3-10-2 m/s; 0.1 X = 0.25, 0.5 mass%
n = 8.33-13.33 1/s; 0.145
d/D = 0.5
Vg = 0.1392.78 x10-4 m3/s ; X ≤ 10 % obj. ηm =1.3-40.7 x103 Pas;
Turbine with 4 flat blades;
PG-L-S/VL = 0.756.3 kW/m3;
0.145
d/D = 0.5
Comments required the presence of the antifoams (0.03-0.1% mass.) solids: Al2O3, Fe2O3 kiselguhr, glass beads (dp = 50-300 μm); sand (dp = 300 μm and powder); 185 exp. points; Δ±11.5% Particles: CaCO3, Fe2O3, BaSO4,
wog = 0.84-4.2 m/s;
n [1/s] = const = 10.83;
σL = 24.3-71.8 x10-3 N/m;
α = (σwater/σL)1/2
DL = 0.68-2.41 m2/s;
Δ±11%
Table 2. The correlations of the volumetric mass transfer coefficient kLa for the agitated gassolid-liquid systems and the applicability of the equations
A
α
β
γ
±Δ, %
Propionibacterium shermanii
6.586
-0.282
-0.0286
0.429
7.8
Saccharomyces cerevisiae
52.44
-0.702
-0.0762
0.514
6.8
Penicillium chrysogenum (aggregates)
0.193
-0.269
0.0288
0.257
8.4
Penicillium chrysogenum (free structure)
33.59
-1.012
-0.0463
0.94
7.6
Type of biomass
Table 3. The values of the coefficient and exponents in Eq. (4)
99
Mass Transfer in Multiphase Mechanically Agitated Systems
2. Experimental In this part of the chapter, our experimental results of the mass transfer coefficient kLa obtained for the gas – liquid or gas – solid – liquid systems agitated in a baffled vessel equipped with single high-speed impeller or the system of the two impellers are presented. Experimental studies were conducted in cylindrical transparent vessel of the inner diameter D = 0.288 m. Geometrical parameters of the vessel used are shown in Fig. 1. The vessel, equipped with a flat bottom and four baffles of the width B = 0.1D, was filled with liquid up to the height H = D (Fig. 1a) and H = 2D (Fig. 1b). The working liquid volumes were VL = 0.02 m3 and VL = 0.04 m3, respectively. In the vessel with single impeller the impeller was placed at a hight h = 0.33D. In the tall vessel two high-speed impellers were located on the common shaft. The distance of the impeller from the bottom of the vessel was h1 = 0.167H for the lower and h2 = 0.67H for the upper impeller, respectively. All impellers have diameter d = 0.33D. Gas was introduced into liquid through a ring shaped sparger, of the diameter dd = 0.7d. The sparger with 44 symmetrically drilled holes of 2 mm in diameter was located at the distance e = 0.5h1 from the bottom of the vessel. To avoid surface aeration of the liquid which could disturb the measurements, the vessel was covered at the top with a transparent lid. Vg
n
B
Vg
n d
B
Z
H
J
J d
H
e
h2
Z
h e
dd
dd
D
D
(a)
(b)
h1
Fig. 1. Geometrical parameters of the stirred vessel; D = 0.288m; d = 0.33D; a) H = D; b) H = 2D Four types of high-speed agitators (Fig. 2) differing in generated fluid pumping mode were tested: Rushton and Smith turbines (radial flow impellers), A 315 (mixed flow) and HE 3 (axial flow impeller). As a single agitator were used: RT, CD 6 and A 315. The measurements were carried out for gas-liquid and gas-solid liquid systems. Distilled water were used as a continuous phase, whilst air as gas phase. The second dispersed phase in a three-phase system was fraction of sea sand particles with mean diameter dp = 335 μm
100
Mass Transfer in Multiphase Systems and its Applications
and density ρp = 2600 kg/m3. The measurements were conducted under various aeration rates, impeller speeds, and solid particles concentration. The measurements were performed for three different solid concentrations, X = 0.5, 2.5 and 5 mass %. The experiments were conducted at five different values of gas flow rate from the following range: Vg (m3/s) ∈ 〈0; 5.56 × 10-3〉 (superficial gas velocity wog (m/s) ∈ 〈0; 8.53 × 10-3〉). Power consumption was measured using the strain gauge method. a
a b
d= 0 0.75d d
d0 = 0.75 d d
b = 2R
R
Z
Z
(a)
(b)
b
β
β b
Z
Z
d
(c)
(d)
Fig. 2. Agitators used in the study; a) Rushton disc turbine (RT), b) Smith disc turbine (CD 6), c) A 315, d) HE 3 All measurements were carried out within the turbulent regime of the fluid flow in the agitated vessel. During the measurements conducted in the gas-solid-liquid system, impeller speeds higher than the critical impeller speeds nJSG for the three-phase system were maintained. Critical agitator speeds in the gas–solid–liquid system were evaluated on basis of the Zwietering criterion (Zwietering, 1958). To determine the volumetric gas–liquid mass transfer coefficients kLa the unsteady-state gassing-out dynamic method (Van’t Riet, 1979; Ozkan et al., 2000; Lu et al., 2002) was used. The dynamic methods are used in many variants. In this study, the variant in which, at constant values of the impeller speed and gas flow rates, the kind of gas introduced into the vessel is changed was used. The gases were air and nitrogen. At the beginning of the
101
Mass Transfer in Multiphase Mechanically Agitated Systems
experiment, in order to remove oxygen, nitrogen was passed through the system. When the value of dissolved oxygen was lowered, air replaced nitrogen. After interchanging N2 → air, absorption of oxygen followed. The change of the oxygen concentration dissolved in liquid was measured by means of fast oxygen probe (galvanic type) coupled with an oxygen meter (CO-551, ELMETRON). The time delay of the measuring probe was ca. 3 s. This sensor was immersed in the liquid and placed at half distance between the baffles. In calculation of kLa, the response time of the probe should be taken into account (KiełbusRąpała & Karcz, 2009). Response time is defined as the time required by the probe used in the study to measure 63 % of the overall value of the oxygen concentration change (Van’t Riet, 1979) and it is related to the oxygen diffusion through the membrane of the probe. According to this fact, the measured values are sufficiently reliable (error below 6 %) only for the response time of the probe shorter or equal to (1/kLa). Therefore, in the experiments, evaluation of the oxygen probe response time was made by measuring the oxygen concentration changes after moving the probe from a liquid saturated by nitrogen to a saturated oxygen solution. The results indicate that using this probe, the kLa values of less than 0.1 s-1 are reliable. All values obtained in the measurements were lower than 0.1 s-1, so the error resulting from the response time τ could be neglected. The kLa coefficient values were determined from the slope of the plot ln[(C*-C0)/(C*-C)] = f(t). In this dependence, t denotes time whilst C*, C0, and C describe saturation concentration of gas in liquid, and concentrations of the gas at time t = 0 and t, respectively. The calculation was performed using the least-squares method.
3. The results 3.1 The results for gas-liquid system Experimental investigations of the mass transfer process in the two-phase gas–liquid systems enable to determine the changes of the volumetric mass transfer coefficient values with operating parameters (impeller speed n and superficial gas velocity wog). The results for the vessel with single impeller are represented by the data obtained for CD 6 impeller (Fig. 3). In this fig. the dependencies of kLa = f(n) for various values of wog are compared. It follows from the results that for all agitator tested the kLa coefficient value significantly increased with the increase both impeller speed and superficial gas velocity.
6
2
k La x 10 , 1/s
8
4 2 0 8
10
12
n , 1/s
14
16
18
Fig. 3. The dependence of kLa = f(n) for single Smith turbine (CD 6) working in a gas–liquid system; varied values of wog ×103 m/s: ( ◊ ) 1.71; ( ■ ) 3.41; (x) 5.12; ( • ) 6.82; ( ∆ ) 8.53
102
Mass Transfer in Multiphase Systems and its Applications
The data, concerning double impeller systems, obtained for various values of superficial gas velocity wog, are presented in Fig. 4a for the vessel with A 315 – Rushton turbine system and in Fig. 4b for the vessel with Smith turbine–Rushton turbine system. It can be observed that similarly to the vessel with single impeller, volumetric mass transfer coefficient is strongly affected by both impeller speed and superficial gas velocity. The differences in the kLa values between particular values of superficial gas velocity wog are greater in the case of Smith turbine – Rushton turbine configuration. 8 6
7
8
9
10
11
12
13
14
15
6
4
2
2
10
12
14
16
8
8
6
6
4
4
2
2
2
4
16
k La x 10 , 1/s
2
k La x 10 , 1/s
6
0
0
6
8
10
12
14
16
0
0
8
10
12
14
16
n , 1/s
n , 1/s
(a)
(b)
Fig. 4. The dependence of kLa = f(n) for two configurations of the agitators: a) A 315 (lower)– RT (upper), b) CD 6 (lower) –RT (upper); gas–liquid system; varied values of wog ×103 m/s: (◊) 1.71; ( ■ ) 2.56; ( ∆ ) 3.41; ( • ) 5.12; ( □ ) 6.82
8
8
6
6
4
4
2
2
0
0
2
kL a x 10 , 1/s
According to the literature data our results confirmed that in a gas–liquid system the volumetric mass transfer coefficient is strongly affected by the type of the agitator used for mixing of the system. The comparison of the kLa coefficient values obtained for three single agitators: RT, CD 6 and A 315 are presented in Fig. 5. In the vessel with radial flow both Rushton and Smith turbines the values of kLa coefficient were significantly higher compared to the values characterized the vessel equipped with mixed flow A 315 impeller. This tendency was observed in the whole range of the measurements.
0
2
4 6 3 wog x 10 , m/s
8
10
Fig. 5. The effect of a single impeller type on the kLa coefficient value in a gas-liquid system; n = const = 11.67 1/s; ( ∆ ) A 315; ( ○ ) CD 6; ( □ ) RT The effect of the impeller configuration on the volumetric mass transfer coefficient kLa value is presented in Figs. 6 and 7. The results concerning mass transfer processes conducting in the vessel equipped with two agitators on a common shaft showed that the type of both
103
Mass Transfer in Multiphase Mechanically Agitated Systems
lower and upper impeller strongly affects kLa coefficient values. In Fig. 6 the dependencies kLa = f(n) for different impeller configurations working in a gas-liquid system were compared. Fig. 6a presents the effect of the type of an upper agitator, whilst Fig. 6b the effect of the type of a lower agitator. 8
k La x 10 , 1/s
2
8
6
7
8
9
10
11
12
13
14
15
8
6
6
4
4
2
2
0
0
16
2
k La x 10 , 1/s
10 6 4 2 0 8
10
12
14
16
18
20
6
8
10
12
14
16
n , 1/s
n , 1/s
(a)
(b)
Fig. 6. The effect of the configuration of agitators on the kLa coefficient value; a) the effect of an upper agitator; empty points: RT–A 315 (upper), filled points: RT–HE 3 (upper); b) the effect of lower agitator; empty points: A 315 (lower)–RT; filled points: CD 6 (lower)–RT (upper); gas–liquid system; varied values of wog ×103 m/s: ( ◊♦ ) 1.71; ( ∆▲) 3.41; ( □■ ) 6.82
9
7
7
5
5
3
3
8 6
2
k La x 10 , 1/s
9
2
k La x 10 , 1/s
In the two-phase distilled water–air system significantly higher values of the volumetric mass transfer coefficient were obtained using the set of the impellers with A 315 as an upper one. Comparison of the kLa coefficient values for three chosen values of superficial gas velocity wog and both configurations differ in an upper impeller is presented in Fig. 6a, 7a. The A 315 impeller (data represent by empty points in Fig. 6a), which generates radial-axial fluid flow in the vessel, let to ensure more advantageous conditions for conducting of mass transfer process, comparing with generating typical axial liquid circulation HE 3 impeller (data represent by filled points in Fig. 6a). At the constant values of agitator speeds, the differences in kLa coefficient values increase with the increase of quantity of gas phase introduced into the liquid volume. At the gas velocity wog = 6,28×10-3 m/s, kLa values in the system agitated by RT–A 315 configuration were over 20 % higher, than those obtained analogously using RT–HE 3 set of agitators.
1
1
0
2
4
6 3
w og x 10 , m/s
(a)
8
4 2 0 0
2
4 6 3 w og x 10 , m/s
8
(b)
Fig. 7. Dependence kLa = f(wog) for different impeller configuration; a) various upper impeller: filled points: RT-HE 3, empty points: RT-A 315, n = 12.5 1/s (triangles), n = 15.83 1/s (circles); b) various lower impellers: ( ∆ ) A 315-RT, ( □ ) CD 6-RT; n = 13.33 1/s;
104
Mass Transfer in Multiphase Systems and its Applications
Comparison of the results obtained for double-impeller system differ in a lower impeller (Fig. 6b) shows, that at constant value of the impeller speed, the highest values of the kLa coefficient were obtained using Smith turbine–Rushton turbine configuration (data represent by filled points in Fig. 6b). At higher values of superficial gas velocity the differences between volumetric mass transfer coefficient values adequate to each configuration increased. The A 315 impeller, which differs in the generated profile of the fluid circulation from the turbine, is less effective as a lower impeller for the mass transfer processes in the agitated vessel comparing with CD 6 impeller (Fig. 7b). The results of the studies of the volumetric mass transfer coefficient in the gas-liquid system were described mathematically, by means of the dependency, which connect kLa coefficient with unit power consumption (PG-L/VL, W/m3) and superficial gas velocity (wog, m/s): B
⎛P ⎞ kL a = A ⎜ G − L ⎟ wogC V ⎝ L ⎠
(5)
The values of the coefficient A and exponents B, C in this Eq. are collected in Table 4 for single impeller system and in Table 5 for all tested configurations of double impeller. In these tables mean relative errors ±Δ for each set of agitators is also presented. For the vessel equipped with single impeller Eq. (5) is applicable within following range of the measurements: PG-L/VL ∈ <160; 5560 W/m3>; wog ∈ <1.71×10-3; 8.53×10-3 m/s>. The range of an application of this equation for the double impeller systems is as follows: Re ∈ <7.9×104; 16.3×104>; PG-L/VL ∈ <540; 4500 W/m3>; wog ∈ <1.71×10-3; 6.82×10-3 m/s>. No.
Impeller
A
B
C
±Δ, %
1. 2. 3.
Rushton Turbine CD 6 A 315
0.029 0.028 0.122
0.44 0.374 0.432
0.534 0.622 0.79
3.7 3.3 5.2
Table 4. The values of the coefficient A and exponents B, C in Eq. (5) for single impeller systems (Kiełbus-Rąpała et al., 2010) No. 1. 2. 3. 4.
Configuration of impellers lower upper Rushton Turbine A 315 Rushton Turbine HE 3 A 315 Rushton Turbine CD 6 Rushton Turbine
A
B
C
±Δ, %
0.098 0.081 0.027 0.092
0.404 0.374 0.466 0.334
0.689 0.636 0.575 0.6
7 6.5 3 2.6
Table 5. The values of the coefficient A and exponents B, C in Eq. (5) for double impeller systems (Kiełbus-Rapała & Karcz, 2010) 3.2 The results for gas-solid-liquid system On the basis of the experimental studies performed within turbulent regime of the liquid flow the volumetric mass transfer coefficient values for gas-solid-liquid systems agitated by single or double impellers were determined. The results obtained confirm that in the system with solid particles the kLa coefficient value is strongly affected by operating parameters, and also the presence and concentration of solid phase in the agitated systems.
105
Mass Transfer in Multiphase Mechanically Agitated Systems
The results of the measurements of volumetric mass transfer coefficients kLa in two phase gas–liquid and three phase gas–solid–liquid system agitated by single CD 6 impeller are compared in Fig. 8 (Karcz & Kiełbus–Rąpała, 2006). In this Fig. empty points are ascribed to the two–phase system whilst filled points correspond to the three–phase system with the concentration of the solid particles 0.5 (Fig. 8a) and 2.5 mass% (Fig. 8b), respectively. 10
14
8
k La x 10 , 1/s
6
2
2
k La x 10 , 1/s
10
4 2 0
8 6 4 2 0
8
10
12
14
n , 1/s
(a)
16
18
8
10
12
14
16
18
n , 1/s
(b)
Fig. 8. Dependence kLa = f(n) for a single impeller CD 6; filled points: X = 0 mass %; empty points: a) X = 0.5 mass %, b) X = 2.5 mass %; various wog ×103 m/s: ( ◊♦ ) 1.71; ( □■ ) 3.41; (+ ×) 5.12; ( ○• ) 6.82; ( ∆▲ ) 8.53 (Karcz & Kiełbus–Rąpała, 2006) Analyzing the data in this Fig it could be concluded that in gas-solid-liquid system both superficial gas velocity and impeller speed influenced kLa coefficient value. Similarly to the two-phase system kLa coefficient value depends on the impeller speeds linearly and kLa increases with the increase of n. Also the increase in aeration rate of three-phase system (described by superficial gas velocity wog) causes the increase of the volumetric mass transfer coefficient. It follows from the results that introducing solids to the system affects volumetric mass transfer coefficient kLa. In the system with 0.5% of solid particles inside, the values of the kLa are significantly higher than in the two–phase system (Fig. 8a). In coalescing system, it can be explained that solids in a small quantity during their movement in the system hit the gas bubbles, which are breaking into the smaller ones and in consequence, the interfacial area increases. However, adding more particles – 2.5 mass %, causes the decrease of kLa values. For lower values of superficial velocity wog, the volumetric mass transfer coefficient values are even lower than those obtained in the gas – liquid system (Fig. 8b). Results of the kLa coefficient measurements for two double-impeller configurations working in gas-liquid, and gas-solid-liquid systems are compared in next Figs (Kiełbus-Rapała & Karcz, 2009). The data for A 315 (lower)–RT (upper) impeller configuration are presented in Fig. 9, whilst those agitated by CD 6 (lower)–RT (upper) can be found in Fig. 10. In these figures, similarly to the data in Fig. 8 filled points are related to the two-phase system whilst empty points correspond to the three-phase system with the concentration of solid particles 0.5 mass % (Figs 9a, 10a) and 2.5 mass % (Figs 9b, 10b), respectively. The results for the system agitated by two impellers on a common shaft show the same dependency of the volumetric mass transfer coefficient as was observed in the vessel equipped with single impeller. In the system with 0.5 mass % of solid particles, the values of kLa are significantly higher compared to the data for two-phase system for both
106
Mass Transfer in Multiphase Systems and its Applications
configurations of the impellers (Figs. 9a, 10a). It is worth to notice that the differences between the kLa values for the system with or without particles are greater for the A 315–RT configuration (Fig. 9). In the three-phase system stirred by CD 6–RT impellers, volumetric mass transfer coefficients for the lowest values of superficial gas velocity were even lower than those for gas-liquid system. These observations are also confirmed by the literature results concerning single-impeller (Alper et al., 1980; Özbek & Gayik, 2001) or doubleimpeller (Galaction et al., 2004) systems. For low concentration of solids, the increase of kLa values can be explained by the interaction of particles with gas bubbles. The particles present in the liquid cause an increase in the turbulence on the film surrounding the gas bubbles, promoting thus the bubbles surface renewal and breaking, or leading to a smaller effective diffusion layer (Galaction et al., 2004; Alper et al., 1980; Kluytmans et al., 2003). Solids in low concentration and of small particle size can, during their movement in the system, collide and interact with the gas–liquid interface and, in consequence, the gas bubbles break into smaller ones causing an increase in interfacial area (Kiełbus-Rapała & Karcz, 2009). 8
k La x 10 , 1/s
6
2
6
2
k La x 10 , 1/s
8
4 2
4 2 0
0 6
8
10
12
14
6
16
8
10
12
14
16
n , 1/s (b)
n , 1/s
(a)
10
10
8
8
6
6
4
4
2
2
0
0
10
12
14
n , 1/s (a)
16
2
10
k La x 10 , 1/s
2
k La x 10 , 1/s
Fig. 9. Dependence kLa = f(n) for configuration A 315 (lower)–Rushton turbine (upper); filled points: X = 0 mass %; empty points: a) X = 0.5 mass %, b) X = 2.5 mass %; various wog ×103 m/s: ( ◊♦ ) 1.71; ( ∆▲ ) 3.41; ( □■ ) 6.82 (Kiełbus–Rąpała & Karcz, 2009)
8 6 4 2 0 8
10
12
14
16
18
n , 1/s (b)
Fig. 10. Dependence kLa = f(n) for the stirrers design CD 6 (lower)–Rushton turbine (upper); filled points: X = 0 mass %; empty points: a) X = 0.5 mass %, b) X = 2.5 mass %; various wog ×103 m/s: ( ◊♦ ) 1.71; ( ∆▲ ) 3.41; ( ○• ) 5.12; ( □■ ) 6.82 (Kiełbus–Rąpała & Karcz, 2009)
107
Mass Transfer in Multiphase Mechanically Agitated Systems
6
5
5
4
4
3
3
2
2
1
1
0
1
2
3 3
3
P G-L-S /V L x 10 , W/m
2
6
k La x 10 , 1/s
2
k La x 10 , 1/s
The investigations of mass transfer process in the system agitated by double-impellers confirm that the volumetric mass transfer coefficient increases, compared to the system without solids, only below a certain level of particles concentration. Introducing more particles, X = 2.5 mass % into the system causes a decrease of kLa in A 315–RT (Fig. 9b) as well as in CD 6–RT (Fig. 10b) configuration. This tendency (reduction of kLa with increasing solid concentrations) was observed also in literature (Özbek & Gayik, 2001). It was proposed that increasing solid concentration causes an increase of slurry viscosity, resulting in an increase of coalescence processes and, in consequence, decrease of kLa coefficients. The effect of solids on kLa could be probably associated with the differences in flow patterns generated in the agitated vessel as seen by the significant differences in the kLa values obtained using different impeller designs. Özbek and Gayik (2001) stated that the concentration at which kLa began to decline depended on solids type and size of the particles. The results obtained for the solid concentration X = 2.5 mass % (Kiełbus-Rapała & Karcz, 2009) differ from those of a single-impeller system (Fig. 8) so the effect of particles with this concentration for the double – impeller system was not the same. Although in both cases, the values of kLa were lower compared to the system with X = 0.5 mass %, kLa coefficients were significantly lower compared to a gas–liquid system at all wog values (Figs 9, 10), whilst in a single-impeller system (Fig. 8b), the volumetric mass transfer coefficient values were lower only for lower values of superficial gas velocity wog (Karcz & Kiełbus-Rapała, 2006). The effect of the solid phase concentration on the volumetric mass transfer coefficient value for both impeller configurations differ in lower impeller is presented in Fig. 11 (Kiełbus– Rąpała & Karcz, 2009). The values of kLa coefficient, obtained at a constant value of superficial gas velocity for the system with different solid concentration agitated by A 315RT configuration (Fig. 11a) and CD 6-RT (Fig. 11b) are compared. In this Fig. triangles described data for gas-liquid system, squares – X = 0.5 mass%, circles – X = 2.5 mass%. 6
6
5
5
4
4
3
4
3
1
2
3
4 3
5
6
3
P G-L-S /V L x 10 , W/m
(a) (b) Fig. 11. Effect of the solid concentration on kLa value for double impeller configuration; a) A 315 (lower)–Rushton turbine (upper), b) CD 6 (lower)–Rushton turbine (upper); wog = const = 3.41 × 10-3 m/s, X = 0 mass % (triangles); X = 0.5 mass % (squares); X = 2.5 mass % (circles) (Kiełbus–Rąpała & Karcz, 2009) In the three-phase system agitated by both impeller configurations differ in an upper impeller type significantly lower kLa coefficient value were obtained in the system with solid
108
Mass Transfer in Multiphase Systems and its Applications
concentration X = 2.5 mass %. The data for RT-A 315 and RT-HE 3 agitator design are compared in Fig. 12 in which squares concerned system with X = 0.5 mass% whilst triangles : X = 2.5 mass %.
8
2
k La x 10 , 1/s
10
6 4 2 10
12
14
16
18
20
n, 1/s Fig. 12. The dependence of kLa = f(n) for two configurations of the agitator working in gas– solid–liquid system; empty points: RT (lower)–A 315 (upper), filled points: RT (lower)– HE 3 (upper); various values of X: ( □■ ) 0.5 mass %; ( ∆▲ ) 2.5 mass % The effect of the single agitator type on the volumetric mass transfer coefficient kLa is presented in Fig. 13. Comparing the results obtained for each impeller it can be stated that, in general, the highest values of the kLa coefficient are characterized for Rushton turbine. However, at higher values of the superficial gas velocity wog the better results of the volumetric mass transfer coefficient correspond to CD 6 impeller. The A 315 impeller, which differs in the generated profile of the liquid circulation from the turbines, is less effective for the mass transfer processes in the agitated vessel (Karcz & Kiełbus-Rąpała, 2006).
2
kLa x 10 , 1/s
10
10
8
8
6
6
4
4
2
2
0
0
0
2
4
3
6
8
10
wog x 10 , m/s Fig. 13. Comparison of the kLa = f(wog) for different single impellers working in the threephase system with solid concentration X = 2.5 mass %; ( □ ) RT, n = 13.33 1/s; ( ○ ) CD 6, n = 13.33 1/s; ( ∆ ) A 315, n = 12.50 1/s
109
Mass Transfer in Multiphase Mechanically Agitated Systems
The effect of upper agitator type on the volumetric mass transfer coefficient value in the gas–solid–liquid system is presented in Fig. 14.
2
k La x 10 , 1/s
10 6.82
8
6.82 3.41
6 4
RT- A 315 RT- HE 3
3.41 1.71
1.71
2 0
2 % X =10.5 mass
3
5 X4= 2.5 mass%
6
Fig. 14. Comparison of values of kLa coefficient for two impeller configurations, working in gas–solid–liquid systems; X ≠ const; n = 15 1/s; various values of superficial gas velocity wog ×10-3 m/s In the three–phase system that, which agitator ensure better conditions to conduct the process of gas ingredient transfer between gas and liquid phase, depends significantly on the quantity of gas introduced into the vessel. Comparison of values of kLa coefficient for two impeller configurations, working in gas–solid–liquid systems with two different solid concentrations is presented in Fig. 14. At lower value of superficial gas velocity (wog = 1.71 ×10-3 m/s) both in the system with lower solid particles concentration X = 0.5 mass % and with greater one: X = 2.5 mass %, higher of about 20 % values of volumetric mass transfer coefficient were obtained in the system agitated by means of the configuration with HE 3 impeller. With the increase of gas velocity wog the differences in the values of kLa coefficient achieved for two tested impellers configuration significantly decreased. Moreover, in the system with lower solid concentration at the velocity wog = 3.41×10-3 m/s, in the whole range of impeller speeds, kLa values for both sets of impellers were equal. Completely different results were obtained when much higher quantity of gas phase were introduced in the vessel. For high value of wog for both system including 0.5 and 2.5 mass % of solid particles, more favourable was configuration Rushton turbine – A 315. Using this set of agitators about 20 % higher values of the volumetric mass transfer coefficient were obtained, comparing with the data characterized the vessel with HE 3 impeller as an upper one (Fig. 12). The data obtained for three–phase systems were also described mathematically. On the strength of 150 experimental points Equation (2) was formulated: b
⎛ ⎞ ⎛P ⎞ 1 kL a = A ⎜ G-L-S ⎟ wog c ⎜⎜ ⎟⎟ 2 V ⎝ L ⎠ ⎝ 1 + m1X + m2 X ⎠
(6)
110
Mass Transfer in Multiphase Systems and its Applications
The values of the coefficient A, m1, m2, and exponents B, C in this Eq. are collected in Table 6 for single impeller system and in Table 7 for the configurations of double impeller differ in a lower one. In these tables mean relative error ±Δ is also presented. For the vessel equipped with single impeller Eq. (6) is applicable within following range of the measurements: PG-L3 -3 -3 S/VL ∈ <118; 5700 W/m >; wog ∈ <1.71×10 ; 8.53×10 m/s>; X ∈ <0.5; 5 mass %>. The range of an application of this equation for the double impeller systems is as follows: PG-L-S/VL ∈ <540; 5960 W/m3 >; wog ∈ <1.71×10-3; 6.82×10-3 m/s>; X ∈ <0.5; 5 mass %>. No.
Impeller
A
b
c
m1
m2
±Δ, %
Exp. point
1.
Rushton turbine (RT)
0.031
0.43
0.515
-186,67
11.921
6.8
100
2.
Smith turbine (CD 6)
0.038
0.563
0.67
-388.62
23.469
6.6
98
3.
A 315
0.062
0.522
0.774
209.86
-11.038
10.3
108
Table 6. The values of the coefficient A, m1, m2 and exponents b, c in Eq. (6) for single impeller systems (Kiełbus-Rąpała et al., 2010)
No.
Configuration of impellers
A
b
c
m1
m2
±Δ, %
lower
upper
1.
CD 6
RT
0.164
0.318
0.665
0.361
8.81
3
2.
A 315
RT
0.031
0.423
0.510
-0.526
-8.31
4
Table 7. The values of the coefficient A, m1, m2 and exponents b, c in Eq. (6) for double impeller systems (Kiełbus-Rąpała & Karcz, 2009) The results of the kLa coefficient measurements for the vessel equipped with double impeller configurations differ in an upper impeller were described by Eq. 7. B
⎛P ⎞ 1 kL a = A ⎜ G − L − S ⎟ wogC V mX 1 + L ⎝ ⎠
(7)
The values of the coefficient A, m, and exponents B, C in this Eq. for both impeller designs are collected in Table 8. The range of application of Eq. 2 is as follows: Re ∈ <9.7; 16.8×104>; PG-L-S/VL ∈ <1100; 4950 W/m3>; wog ∈ <1.71×10-3; 6.82×10-3 m/s>; X ∈ <0; 0.025>.
No.
Configuration of impellers
A
B
C
m
±Δ, %
lower
upper
1.
Rushton Turbine
A 315
0.103
0.409
0.695
4.10
4.8
2.
Rushton Turbine
HE 3
0.031
0.423
0.510
6.17
6.4
Table 8. The values of the coefficient A and exponents B, C in Eq. (7) (Kiełbus-Rąpała & Karcz 2010)
111
Mass Transfer in Multiphase Mechanically Agitated Systems
4. Conclusions In the multi – phase systems the kLa coefficient value is affected by many factors, such as geometrical parameters of the vessel, type of the impeller, operating parameters in which process is conducted (impeller speed, aeration rate), properties of liquid phase (density, viscosity, surface tension etc.) and additionally by the type, size and loading (%) of the solid particles. The results of the experimental analyze of the multiphase systems agitated by single impeller and different configuration of two impellers on the common shaft show that within the range of the performed measurements: 1. Single radial flow turbines enable to obtain better results compared to mixed flow A 315 impeller. 2. Geometry of lower as well as upper impeller has strong influence on the volumetric mass transfer coefficient values. From the configurations used in the study for gasliquid system higher values of kLa characterized Smith turbine (lower)–Rushton turbine and Rushton turbine–A 315 (upper) configurations. 3. In the vessel equipped with both single and double impellers the presence of the solids in the gas–liquid system significantly affects the volumetric mass transfer coefficient kLa. Within the range of the low values of the superficial gas velocity wog, high agitator speeds n and low mean concentration X of the solids in the liquid, the value of the coefficient kLa increases even about 20 % (for single impeller) comparing to the data obtained for gas–liquid system. However, this trend decreases with the increase of both wog and X values. For example, the increase of the kLa coefficient is equal to only 10 % for the superficial gas velocity wog = 5.12 x10-3 m/s. Moreover, within the highest range of the agitator speeds n value of the kLa is even lower than that obtained for gas–liquid system agitated by means of a single impeller. In the case of using to agitation two impellers on the common shaft kLa coefficient values were lower compared to a gas–liquid system at all superficial gas velocity values. 4. The volumetric mass transfer coefficient increases, compared to the system without solids, only below a certain level of particles concentration. Introducing more particles, X = 2.5 mass % into the system causes a decrease of kLa in the system agitated by both single and double impeller systems. 5. In the gas–solid–liquid system the choice of the configuration (upper impeller) strongly depends on the gas phase participation in the liquid volume: -The highest values of volumetric mass transfer coefficient in the system with small value of gas phase init were obtained in the vessel with HE 3 upper stirrer; -In the three-phase system, at large values of superficial gas velocity better conditions to mass transfer process performance enable RT–A 315 configuration. Symbols a B b C D d
length of the blade width of the baffle width of the blade concentration inner diameter of the agitated vessel impeller diameter
m m m g/dm3 m m
112
Mass Transfer in Multiphase Systems and its Applications
dd dp e H h1 h2 i J kLa n nJSG P R t VL Vg
diameter of the gas sparger particles diameter distance between gas sparger and bottom of the vessel liquid height in the agitated vessel off – bottom clearance of lower agitator off – bottom clearance of upper agitator number of the agitators number of baffles volumetric mass transfer coefficient agitator speed critical impeller speed for gas – solid – liquid system power consumption curvature radius of the blade time liquid volume gas flow rate
m m m m m m
wog X Z
superficial gas velocity (= 4 Vg /πD2)· mass fraction of the particles number of blades
m s-1 % w/w
s-1 s-1 s-1 W m s m3 m3s-1
Greek Letters
β ρp
pitch of the impeller blade density of solid particles
deg kgm-3
Subscripts G-L G-S-L
refers to gas – liquid system refers to gas – solid – liquid system
5. References Alper, E.; Wichtendahlet, B. & Deckwer, W.D. (1980). Gas absorption mechanism in catalytic slurry reactions. Chemical Engineering Science, 35, 217-222 Arjunwadkar, S.J.; Sarvanan, K.; Pandit, A.B. & Kulkarni, P.R. (1998). Gas - liquid mass transfer in dual impeller bio-reactor. Biochemical Engineering Journal, 1, 93-96 Bartos, T.M. & Satterfield, C.N. (1986). Effect of finely divided solids on mass transfer between a gas and organic liquid. AICHE Journal, 32, 773-780 Brehm, A.; Oguz, H. & Kisakurek, B. (1985). Gas - liquid mass transfer data in an three phase stirred vessel. Proceedings of the 5th European Conference on Mixing, pp. 419-425, Wurzburg, Germany, June 10-12, 1985 Brehm, A. & Oguz, H. (1988). Measurement of gas/liquid mass transfer: peculiar effects In aqueous and organic slurries. Proceedings of the 6th European Conference on Mixing, pp. 413-420, Pavia, Italy, 24-26.05.1988 Chandrasekaran, K. & Sharma, M.M. (1977). Absorption of oxygen in aqueous solutions of sodium sulfide in the presence of activated carbon as catalyst. Chemical Engineering Science, 32, 669-675 Chapman, C.M.; Nienow, A.W.; Cooke, M. & Middleton, J.C. (1983). Particle - gas - liquid mixing in stirred vessels. Part IV: Mass transfer and final conclusions. Chemical Engineering Research & Design, 61, 3, 182-185
Mass Transfer in Multiphase Mechanically Agitated Systems
113
Dohi, N.; Matsuda, Y.; Itano, N.; Shimizu, K.; Minekawa, K. & Kawase, Y. (1999). Mixing characteristics in slurry stirred tank reactors with multiple impellers. Chemical Engineering Communications, 171, 211-229 Dohi, N.; Takahashi, T.; Minekawa, K. & Kawase, Y. (2004). Power consumption and solid suspension performance of large - scale impellers in gas - liquid - solid three phase stirred tank reactors. Chemical Engineering Journal, 97, 103-114, doi:10.1016/S1385-8947(03)00148-7 Dutta, N.N. & Pangarkar, V.G. (1995). Critical impeller speed for solid suspension in multi impeller three phase agitated contactors. Canadian Journal of Chemical Engineering, 73, 273-283 Fujasova, M.; Linek, V. & Moucha, T. (2007). Mass transfer correlations for multiple impeller gas - liquid contactors. Analysis of the effect of axial dispersion in gas liquid phases on “local” kLa values measured by the dynamic pressure method in individual stages of the vessel. Chemical Engineering Science, 62, 1650-1669, doi:10.1016/j.ces.2006.12.03 Galaction, A.I.; Cascaval, D.; Oniscu, C. & Turnea, M. (2004). Modeling of oxygen transfer in stirred bioreactors for bacteria, yeasts and fungus broths. Proceedings of the 16th International Congress of Chemical & Processing Engineering, CHISA, Paper F1.5 Praha, Czech Republic, August 22-26, 2004 Garcia-Ochoa, F. & Gomez, E. (2009). Bioreaktor scale-up oxygen transfer rate in microbial processes. An overview. Biotechnology Advances, 27, 153-176. Gogate, P.R.; Beenackers, A.A.C.M. & Pandit A.B. (2000). Multiple - impeller systems with special emphasis on bioreactors: a critical review. Biochemical Engineering Journal, 6, 109-144 Gogate, P.R. & Pandit, A.B. (1999). Survey of measurement for gas-liquid mass transfer coefficient in bioreactors. Biochemical Engineering Journal, 4, 7-15 Greaves, M. & Loh, V.Y. (1985). Effect of hight solids concentrations on mass transfer and gas hold-up in three – phase mixing. Proceedings of 5th European Conference on Mixing, pp. 451-467, Germany, Wurzburg, 10-12.06.1985 Harnby, N.; Edwards, M.F. & Nienow A.W. (1997). Mixing in the process industries, second edition, Butterworth, Heinemann, ISBN 0 7506 37609, Oxford Jahoda, M.; Machoň, V.; Veverka, P. & Majiřová, H. (2000). Homogenisation of the liquid in three - phase multiimpeller stirred reactor. Proceedings of the 14th International Congress of Chemical & Processing Engineering, CHISA, Paper E4.5, Praha, Czech Republic August 27-31, 2000 Jin, B. & Lant, P. (2004). Flow regime, hydrodynamics, floc size distribution and sludge properties in activated sludge bubble column, air - lift and aerated stirred reactors. Chemical Engineering Science, 59, 2379-2388, doi:10.1016/j.ces.2004.01.061 Joosten, G.E.H; Schilderet, J.G.M. & Jansen, J.J. (1977). The influence of suspended solid material on the gas-liquid mass transfer in stirred gas-liquid contactors. Chemical Engineering Science, 32, 563-570 Karcz, J. & Kiełbus—Rąpała, A. (2006). An effect of solids on the volumetric gas - liquid mass - transfer coefficient in mechanically agitated gas - solid - liquid system. Proceedings of the 17th International Congress of Chemical & Processing Engineering, CHISA, Praha, Czech Republic, August 27-31, 2006
114
Mass Transfer in Multiphase Systems and its Applications
Kiełbus—Rąpała, A. & Karcz, J. (2009). Influence of suspended solid particles on gas-liquid mass transfer coefficient in a system stirred by double impellers. Chemical Papers, 63, 2, 188-196, doi:10.2478/s11696-009-013-y Kiełbus—Rąpała, A. & Karcz, J. (2010). The influence of stirrers’ configuration on the volumetric gas-liquid mass transfer coefficient in multiphase systems. Paper P5.80. Proceedings of the 19th International Congress of Chemical & Processing Engineering, CHISA, Praha, Czech Republic, August 28- September 1, 2010 Kiełbus—Rąpała, A., Karcz, J. & Cudak, M. (2010). The effect of physical properties of the liquid phase on the gas-liquid mass transfer coefficient in the two- and three-phase agitated systems. Proceedings of the 37th International Conference of Slovak Society of Chemical Engineering, pp. 1310-1318, ISBN 978-80-227-3290-1, Tatranske Matliare, Slovakia, May 24-28, 2010 Kordac, M. & Linek, V. (2010). Efect of solid particle size on mass transfer between gas and liquid. Paper I3.1. Proceedings of the 19th International Congress of Chemical & Processing Engineering, CHISA, Praha, Czech Republic, August 28- September1, 2010 Kluytmans, J.H.J.; Wachem, B.G.M;, Kuster, B.F.M. & Schouten, J.C. (2003). Mass transfer in sparged and stirred reactors: influence of carbon particles and electrolyte. Chemical Engineering Science, 58, 4719-4728, doi:10.1016/j.ces.2003.05.004 Kralj, F. & Sincic, D. (1984). Hold – up and mass transfer in two- and three - phase stirred tank reactor, Chemical Engineering Science, 39, 604-607 Lee, J.C.; Ali, S.S. & Tasakorn, P. (1982). Influence of suspended solids on gas-liquid mass transfer in an agitated tank. Proceedings of 4th European Conference on Mixing, pp. 399-408, Noordwijkerhout, The Netherlands, April, 1982 Lemoine, R. & Morsi, B.I. (2005). An algorithm for predicting the hydrodynamic and mass transfer parameters in agitated reactors. Chemical Engineering Journal, 114, 9-31 Linek, V.; Moucha, T. & Sinkule, J. (1996). Gas - liquid mass transfer in vessel stirred with multiple impellers - I. Gas - liquid mass transfer characteristics in individual stages. Chemical Engineering Science, 51, 3203-3212 Linek, V.; Vacek, V. & Benes, P. (1987). A critical review and experimental verification of correct use of dynamic method for the determination of oxygen transfer in aerated agitated vessels to water, electrolytic solutions and viscous liquids. Chemical Engineering Journal, 34, 11-34 Linek, V.; Benes, P. & Vacek, V. (1982). A critical review and experimental verification of correct use of dynamic method for the determination of oxygen transfer in aerated agitated vessels to water, electrolytic solutions and viscous liquids. Chemical Engineering Journal, 25, 77-88 Littlejohns, J.V. & Daugulis, A.J. (2007). Oxygen transfer in a gas - liquid system containing solids of varying oxygen affinity. Chemical Engineering Journal, 129, 67-74, doi:10.1016/j.cej.2006.11.002 Lu, W.M.; Hsu, R.C. & Chou, H.S. (1993). Effect of solid concentration on gas liquid mass transfer in a machanically agitated three phase. Journal Chin. I. Chemical Engineering, 24, 31-39 Lu, W.M.; Wu, H.Z. & Chou, C.Y. (2002). Gas recirculation rate and its influences on mass transfer in multiple impeller systems with various impeller combinations. The Canadian Journal of Chemical Engineering, 80, 51-62
Mass Transfer in Multiphase Mechanically Agitated Systems
115
Machon, V.; Vlcek, J. & Hudcova, V. (1988). Multi-impeller gas-liquid contactors. Proceedings of the 6th European Conference on Mixing, pp. 351-360, Pavia, Italy, 1988, May 24-26 Majiřova, H.; Prokopa, T.; Jagoda, M. & Machoň, V. (2002). Gas hold – up and power input in two - and three - phase dual - impeller stirred reactor. Proceedings of the 15th International Congress of Chemical & Processing Engineering, CHISA, Praha, Czech Republic, 2002, August 25-29 Markopoulos, J.; Christofi,C. & Katsinaris, J. (2007). Mass transfer coefficients in mechanically agitated gas-liquid contactors. Chemical Engineering & Technology 30, 7, 829-834, doi: 10.1002/ceat.200600394 Martin, M.; Montes, F.J. & Galan, M.E. (2008). On the contribution of the scales of mixing to the oxygen transfer in stirred tanks. Chemical Engineering Journal, 145, 232-241 Mills, D.B.; Bar, R. & Kirwan, D.J. (1987). Effect of solid on oxygen transfer in agitated three phase systems. AICHE Journal, 33, 1542 Moilanen, P.; Laakkonen, M.; Visuri, O.; Alopaeus, V. & Aittamaa, J. (2008). Modelling mass transfer in an aerated 0.2 m3 vessel agitated by Rushton, Phasejet and Combijet impellers. Chemical Engineering Journal, 142, 92-108 Moucha, T.; Linek, V. & Prokopová, E. (2003). Gas hold - up, mixing time and gas - liquid volumetric mass transfer coefficient of various multiple - impeller configurations: Rushton turbine, pitched blade and Techmix impeller and their combinations. Chemical Engineering Science, 58, 1839-184, doi:10.1016/S0009-2509(02)00682-6 Nocentini, M.,Fajner, D., Pasquali, G.& Majeli, F. (1993). Gas - liquid mass transfer and holdup in vessels stirred with multiple Rushton turbines: water and glicerol solution. Industrial Engineering & Chemical Research, 32, 19-24 Oguz, H.; Brehm, A. & Deckwer, W.D. (1987). Gas-liquid mass transfer in sparged agitated slurries. Chemical Engineering Science, 42, 1815-1822 Özbek, B. & Gayik, S. (2001). The studies on the oxygen mass transfer coefficient in bioreactor. Proc. Biochem., 36, 729-741 Ozkan, O.; Calimli, A.; Berber, R. & Oguz, H. (2000). Effect on inert solid particles at low concentrations on gas - liquid mass transfer in mechanically agitated reactors. Chemical Engineering Science, 55, 2737-2740 Paul, E.L; Atiemo-Obeng, V.A & Kresta, S.M. (2004). Handbook of Industrial Mixing, WileyInterscience, ISBN 0-471-26919-0, Hoboken, New Yersey Pinelli, D. (2007). The role of small bubbles in gas-liquid mass transfer in stirred vessels and assessment of a two-fraction model for noncoalescent or moderately viscous liquids. Chemical Engineering Science, 62, 3767-3776 Puthli, M.S.; Rathod, V.K. & Pandit, A.B., (2005). Gas - liquid mass transfer studies with triple impeller system on a laboratory scale bioreactor. Biochemical Engineering Journal, 23, 25-30, doi:10.1016/j.bej.2004.10.006 Roman, R.V. & Tudose, R.Z., ( 1997). Studies on transfer processes in mixing vessels: power consumption of the modified Rushton turbine agitators in three - phase systems. Bioprocess Engineering, 17, 307-316 Ruthiya, K.C.; Schaaf, J. & Kuster, B.F.M, (2003). Mechanism of physical and reaction enhancement of mass transfer in a gas inducing stirred slurry reactor. Chemical Engineering Journal, 96, 55-69, doi:10.1016/j.cej.2003.08.05 Van’t Riet, K., (1979). Review of measuring methods and results in nonviscous gas-liquid mass transfer in stirred vessels. Industrial Engineering Chemical Process Design and Development, 18, 357-364
116
Mass Transfer in Multiphase Systems and its Applications
Vasconcelos, J.M.T.; Orvalho, S.C.P.; Rodrigues, A.M.A.F. & Alves, S.S. (2000). Effect of Blade shape on the performance of six bladed disc turbine impellers. Industrial Engineering & Chemical Research, 39, 203-208 Wu, H. (1995). An issue on applications of a disk turbine for gas-liquid mass transfer. Chemical Engineering Science, 50, 17, 2801-2811 Yawalkar, A.A.; Heesink, A.B.M.; Versyeeg, G.F. & Pangarkar, V.G. (2002). Gas-liquid mass transfer coefficient in stirred tank reactors. Canadian Journal of Chemical Engineering, 80, 5, 840-848 Yoshida, M.; Kitamura, A.; Yamagiwa, K. & Ohkawa, A. (1996). Gas hold-up and volumetric oxygen transfer coefficient in an aerated agitated vessel without baffles having forward-reverse rotating impellers. Canadian Journal of Chemical Engineering, 74, 840848 Zhang, G.D.; Cai, W.F., Xu, C.J., Zhou & M. (2006). A general enhancement factor model of the physical absorption of gases in multiphase system. Chemical Engineering Science, 61, 558-568, doi:10.1016/j.ces.2005.07.035 Zwietering, T.N. (1958). Suspending of solids particles in liquid by agitation. Chemical Engineering Science, 8, 244-253.
6 Gas-Liquid Mass Transfer in an Unbaffled Vessel Agitated by Unsteadily Forward-Reverse Rotating Multiple Impellers 1Department
Masanori Yoshida1, Kazuaki Yamagiwa1, Akira Ohkawa1 and Shuichi Tezura2
of Chemistry and Chemical Engineering, Niigata University 2Shimazaki Mixing Equipment Co., Ltd. Japan
1. Introduction Gas-sparged vessels agitated by mechanically rotating impellers are apparatuses widely used mainly to enhance the gas-liquid mass transfer in industrial chemical process productions. For gas-liquid contacting operations handling liquids of low viscosity, baffled vessels with unidirectionally rotating, relatively small sized turbine type impellers are generally adopted and the impeller is rotated at higher rates. In such a conventional agitation vessel, there are problems which must be considered (Bruijn et al., 1974; Tanaka and Ueda, 1975; Warmoeskerken and Smith, 1985; Nienow, 1990; Takahashi, 1994): 1) occurrence of a zone of insufficient mixing behind the baffles and possible adhesion of a scale to the baffles and the need to clean them periodically; 2) formation of large gas-filled cavities behind the impeller blades, producing a considerable