Great American Scrollsaw Patterns Volume 1

SCROLLSAW PATTERNS: Following are the full-size scrollsaw patterns for creating beautiful projects from our CD Scrollsaw Pattern Book. Each pattern is shaded to make it easier to see where to cut and where not to cut. To navigate from page to page, simply use the vertical scrollbar on the right hand side of the screen, or the “Go To” buttons located at the top and bottom of the screen. To print, simply click on the “Printer Icon” at the top of the screen, or choose “Print” from the “File” pull-down menu. Be sure to specify which page numbers you want to print, and the number of copies. You can determine the page number from the “Page #” box 4 of 107 at the bottom of the screen. When finished, click the “First Page” button to go back to the beginning to choose another section to view. GREAT AMERICAN PATTERNS TM

Simply click on the button of your choice. INTRO

PHOTOS

HOW-TO

MORE CD’S AVAILABLE

PATTERNS

BACK TO START

Country Plate

Interior Plate Design Stock: 1/4” - 3/8”

Attach to back of Rim with glue or silicone.

Attach to back of Rim with glue or silicone.

Country Plate

Rim Design

Stock: 1/8” - 1/4” Right pattern piece

Pattern overlap line

Rim Design

Dashed line indicates position of Interior Plate Design on back of Rim.

Pattern overlap line

Stock: 1/8” - 1/4” Left pattern piece

Triple Mirror / Picture Frame

Left / Right Overlay Stock: 1/16” - 1/4”, cut 2

Dashed line indicates position of opening on Frame.

Center Overlay Stock: 1/16” - 1/4”

Dashed line indicates position of opening on Frame.

Triple Mirror / Picture Frame

Left & Right Frame Stock: 1/4”, cut 2

Attach hinges of your choice. Small dashed lines indicate placement of Overlay.

Drill starter hole and cut on the solid line for Back Insert. After inserting the photo/mirror, secure the Back in place with a small amount of glue or silicone.

Triple Mirror / Picture Frame

Center Frame Stock: 1/4”

Small dashed lines indicate placement of Overlay. Secure with glue or silicone.

Drill in the corner and cut on the solid line for Back Insert. After inserting the photo/mirror, secure the Back in place with a small amount of glue or silicone.

Cupid Music Box

Side view of Music Box

Top

1 2

3/4 Back

1”

3

Top

Foot Instructions 1. Attach pattern with repositionable spray. 2. Cut out rear shape 3. Cut out the top shape 4. Attach Foot with glue and finishing nails or silicone

Back

Metal Turntable

Music Box Key For music box tune selection and pricing, call THE BERRY BASKET at 1-800-206-9009.

Assembly Instructions Assemble by first attaching the Top to the Frame with glue and finishing nails or silicone. Next attach the music box movement to the topside of the Bottom with screws or silicone. Before the silicone sets, be sure to position the Frame over the Bottom to make sure the music box movement is aligned correctly. Then secure the Bottom to the Frame. Next, attach the Arch and Feet where indicated, securing with wood glue or silicone. Now attach the metal turntable to the bottom of the wood Turntable with silicone and then attach the Figure to the Top. Finally, attach the turntable and key to the music box, and finish as desired. NOTE: It is important that the music box movement bottom is in contact with the wood (topside of the Bottom) in order to have the best tone. If using silicone, be careful to not use too much as it may squeeze out from between the 2 pieces and get into the movement itself.

Frame Stock: 1 1/2”

Cut out for music box

Circle indicates position of key and turntable shafts.

Stock: 1/4”

Arch

Stock: 3/8”

Figure

Top view.

Stock: 3/4”, cut 3

Foot

Fold on dashed line. Rear view

Front

Stock: 1/4”, cut 2

Arch Support

Cupid Music Box

Roundover top edge by sanding.

Cut slots in Top only. Adjust slot, if necessary, for thickness of material used.

Stock: 1/4”, cut 1 each.

Top / Bottom

Small dashed lines indicate placement of Foot on Bottom.

Drill 3/8” in Top for turntable shaft and in Bottom for key.

Dashed line indicates placement of Frame

Cupid Music Box

Turntable

Stock: 1/4”, countersink the bottomside with a 1” forstner bit 1/16” deep. Secure the metal turntable with super glue or silicone.

Dashed line indicates position of metal turntable on bottomside.

Roundover top edge by sanding.

Small Fretted Shelves

Shelf Back Stock: 3/8"

Shelf Back Stock: 3/8"

Shelf Top Stock: 3/8"

Attach to Back with glue and #18 x 3/4” finishing nails or countersink for #4 x 5/8” F.H. screws.

Victorian Rocker

Assembly Instructions To assemble, first insert Seat tab and Back tab into one side. Then attach remaining Side. Tip: to customize this rocker for your favorite seamstress, add a pin cushion to the top of the Seat and secure with glue or silicone.

Seat Stock: 1/4”

Victorian Rocker

Side

Pattern overlap line

Pattern overlap line

Stock: 1/4”, cut 2 Left pattern piece.

Side Stock: 1/4”, cut 2 Right pattern piece.

Apply a small amount of glue to each side tab before assembly.

Victorian Rocker

Back

Stock: 1/4”

5°

Bird House

Drill for #6 x 5/8" F.H. wood screw to hold cover on back

E

Cover (E) Stock: 1/4", cut 2

F

A

F F

F

B F

A

F

H E C

G

D

Bird House Description Item Qty Front Back Bottom Side Cover Roof Overlay Top Floor

A B C D E F G H

1 1 1 2 2 6 2 1

Side (D) Stock: 3/8”

Assembly Instructions Assemble by first attaching the Sides, Top Floor and Bottom to the Front. Next attach the Back to this assembly. Now attach the Roof sections beginning with the bottom section on each side. Then attach the Covers, Overlays, Roof dowel and perch pegs.

Bird House 3/8" dowel

Front (A) Stock: 3/8"

Bore hole for entrance

Drill for peg Top Floor

Side

Small dashed line indicates placement of Overlays.

Bore hole for entrance

Side

Drill for peg

Bottom

Bird House

3/8" dowel

O

Sto ver ck lay :1 /1 6 ( G "- ) 1 /8 ”

,c

ut

2

Cut out for cleanout hole.

Top Floor

Back (B) Stock: 3/8"

Dashed line indicates placement of Cover.

Cut out for cleanout hole.

Side

Side

Assemble using glue and #18 x 3/4” finishing nails. Bottom

Bird House

Bottom (C) Stock: 3/8”

Roof (F) Stock: 1/4”, cut 6

For bottom 2 Roof sections, place the nails closer together to accommodate overhang. Attach Roof with #18 x 5/8” finishing nails. Top

Bird House

Top Floor (H) Stock: 1/4”

Stock: 1/8”, cut 2

Bracket

Floral Letter Holder

Floral Letter Holder

Bottom Stock: 1/8”

Cut 2 outer Dividers on this line.

Cut 1 center Divider on this line.

Stock: 1/8”, cut 3

Divider

Floral Letter Holder

Side

Small Fretted Shelves

Stock: 1/4”, cut 2 Adjust slots, if necessary, for the thickness of material used.

Pattern overlap line

Side Stock: 1/4”

Crest

Stock: 1/4”, cut 2 Use glue and #18 x 5/8” finishing nails to attach Shelves and Crest to Sides.

Pattern overlap line

S

Sto helf c k: 1 /4

”, c

ut

3

Stock: 1/4”

Crest

Attach to front edge of Roof with glue and #18 x 5/8” finishing nails.

Vineyard Weather Station

Stock: 3/4” Top pattern piece

Frame

Pattern overlap line

Bore 2 3/8” holes for 2 3/4” O.D. weather instrument inserts.

Note: cut ends at 70°

Stock: 1/4” Cut 2

Roof

Vineyard Weather Station

Rabbet backside for fretted insert

Stock: 3/4” Bottom pattern piece

Frame

Pattern overlap line

1/4" Rabbet, 1/4" deep

1/4" R Typ.

Vineyard Weather Station

3/4"

20

1 2 3 4

17 1

16 15

1 2 3 4

0

17 1

16 15 16 15

17 1

1 2 3 4

7 8 9 5 6 1

81 9

12 13 14 11 20

0

7 8 9 5 6 1

81 9

12 13 14 11 20

0

7 8 9 5 6 1

81 9

Vineyard Weather Station

Attach to backside of 3/4” Frame stock with glue and #18 x 5/8” finishing nails.

Side Insert Stock: 1/4”, cut 2

Attach to Base with glue and #18 x 5/8” finishing nails.

12 13 14 11

Vineyard Weather Station

Rabbet top edge for fretted Side inserts.

Pattern overlap line

Drill and countersink bottomside to attach Frame with #8 x 1 1/2” FH screws.

Base Stock: 3/4” Right pattern piece

Stock: 3/4” Left pattern piece

Roundover top edge 1/4” R before rabbeting.

Pattern overlap line

Base

Note: Assemble all parts with #18 x 5/8” finishing nails and glue.

Stock: 3/8"

Crest (A)

Victorian Clock

Pattern overlap line

Victorian Clock

Victorian Clock

Base (B) Base (B)

Pattern overlap line

Stock: 3/8" Right pattern piece

Stock: 3/8" Left pattern piece

Description Item Qty Crest Base Front / Back Side Front Rail End Rail Roof Blank

A G

D

11

Assembly Instructions Assemble by first attaching the Sides to the Back, securing with glue and #18 x 5/8” finishing nails. Next, attach the Front. Now, attach the Roofs and the Crest to the front of the Roofs. Then, center the Blank from side to side on the Base and 3/8” in from the back of the Base, and secure in place with glue and finishing nails. Continue, by placing the clock assembly over the Blank and securing in place with glue and nails. Now, attach the Front Rail and End Rails to the edges of the Base, and finish as desired.

C 12

1 2

10 3 9 4 8 7

H F

B

6

5

E

A B C D E F G H

1 1 1 ea 2 1 2 2 1

Stock: 3/8" Cut 1 each Top pattern piece

Front / Back (C)

Pattern overlap line

Bore a 3” hole in front for a 3 1/2” O.D. clock insert.

Victorian Clock

Note: assemble all parts with #18 x 5/8” finishing nails and glue.

Stock: 3/8” Cut 1 each Bottom pattern piece

Front / Back (C)

Pattern overlap line

Victorian Clock

Pattern overlap line

Stock: 3/8” Cut 2 Top pattern piece

Side

Attach to edge of Blank with glue and #18 x 5/8” finishing nails.

Stock: 3/8” Cut 2 Bottom pattern piece

Side

Pattern overlap line

Victorian Clock

Cut top at 28°

Victorian Clock

Pattern overlap line

Stock: 3/8” Left pattern piece

Front Rail (E) Stock: 3/8” Right pattern piece

Blank (H) Stock: 3/8”

Pattern overlap line

Front Rail (E)

Victorian Clock

End Rail (F) Stock: 3/8” Cut 2

Cut Roof at 28°

Cut Roof at 28° Side view of Roof

Back

Roof (G) Stock: 3/8" Cut 2

Front

Pattern overlap line

Home Sweet Home

Frame Stock: 1/4” - 3/8” Left pattern piece

Pattern overlap line

Home Sweet Home

Frame Stock: 1/4" - 3/8" Right pattern piece

Victorian Hand Mirror

Roundover 1/4" R

Frame / Back Stock: 1/4" - 3/8" Top pattern piece

Note: Factory made beveled mirrors are not 100% consistent in size and shape. Therefore, we recommend that you position the mirror in place on the pattern and trace around it with a red pen. Then cut on this solid line for the mirror to fit properly.

Pattern overlap line

Pattern overlap line

Frame / Back Stock: 1/4” - 3/8” Bottom pattern piece

1 Cut mirror opening and

interior design only. Do not cut the outer shape.

Work piece

2 Glue and clamp Back

work piece to Frame work piece. Cut outer shape of mirror.

Beveled mirror

Side view of beveled mirror details Side view of hand cut mirror detail

Front

1/4" R typ.

Beveled edge mirror

Frame/Back Assembly

1/4"

3 Silicone mirror into place.

3/8" 3/8"

1/8" 1/4"

Glue Overlay into place if required.

BAC 1/4" R typ.

Silicone adhesive

Pattern overlap line

Necklace / Key Rack

Frame Stock: 1/4" - 3/8" Left pattern piece

Necklace / Key Rack

Frame

Pattern overlap line

Stock: 1/4" - 3/8" Right pattern piece

Drill for wooden pegs or dowels

Victorian Mirror / Picture Frame

Frame Stock: 1/4" - 3/8" Left pattern piece

Side view beveled mirror details

Front

Beveled edge mirror

1/4" 3/8" BAC 1/4" R typ.

Roundover edge 1/4” R

Silicone adhesive

Pattern overlap line

Cut on this line for beveled edge mirror

Victorian Mirror / Picture Frame

Frame Stock: 1/4” - 3/8” Right pattern piece

SAW TO FIT BEVELED EDGE MIRROR

Pattern overlap line

BEVELED EDGE MIRROR

Cut on this line for hand cut mirror and rabbet backside as shown in the section drawing.

Side view of hand cut mirror detail 1/4" R Typ.

3/8" SILICON ADHESIV E

1/8" 1/4"

Large Shelf

Back Stock: 3/4” Left pattern piece

Pattern overlap line

Rabbet backside for fretted insert

. Drill with a 1/16” drill bit to start bevel cut. Cut clockwise with table tilting down to the right at 3 1/2° or cut counterclockwise with table tilting down to the left at 3 1/2°.

Large Shelf

Back

Pattern overlap line

Stock: 3/4” Right pattern piece

.

Large Shelf

Insert Stock: 1/4”

Insert Stock: 1/4”

Large Shelf

Insert Stock: 1/4"

Note: Optional - cut another blank backing of contrasting material for visual effect as desired.

Large Shelf

Bracket Stock: 3/4” Cut 2

Drill and countersink outside edge for #8 x 1 1/2” FH.

Large Shelf

Drill and countersink to attach Shelf to Bracket and Back with #8 x 1 1/2” FH. screws.

Top

Stock: 3/4” Left pattern piece.

Pattern overlap line

Large Shelf

Pattern overlap line

Top Stock: 3/4” Right pattern piece.

Victorian Basket

Frame Stock: 3/4” Left pattern piece

Drill 1/8” pivot hole before sawing basket free. After routing 1/4” R countersink for #6 x 1 1/4” FH screws.

. Pattern overlap line

Drill a 1/16” hole to start bevel spiral cut. Saw at 3 1/2° with table tilting down to the left and using a #9 blade.

1/8” drill & countersink. Attach pivot foot with #6 x 3/4” FH screw.

Victorian Basket

Frame Stock: 3/4” Right pattern piece

Roundover edges as desired 1/4” R.

.

Pattern overlap line

Roundover 1/4’R.

Planter Basket

End Stock: 3/4’ Cut 2

Pattern overlap line

Planter Basket

Top / Base Stock: 3/4”, cut 1 each Left pattern piece.

Drill and countersink bottomside of Base to attach Sides with #& x 1 1/2” FH. screws.

End

. Drill a 1/16” hole to start bevel cut. Cut clockwise with table tilting down to the right at 3° or cut counterclockwise with table tilting down to the left at 3°.

Pattern overlap line

Planter Basket

Top / Base Stock: 3/4”, cut 1 each Right pattern piece.

Roundover outside edges 1/4” R.

Stock: 1/4” Cut 2

Insert

Planter Basket

Stock: 1/4" Cut 2

Insert

Planter Basket

Stock: 1/4" Cut 2

Insert

Planter Basket

Optional corner joint detail Side stock: 3/4” Cut 2

Side Stock: 3/4”, cut 2 Right pattern piece

End

Pattern overlap line

Planter Basket

Rabbet Backside for fretted insert.

Side Drill and countersink to attach Ends with #7 x 1 1/2” FH. screws.

Stock: 3/4”, cut 2 Left pattern piece

1/4" R 1/4" x 1/4" Rabbet

Pattern overlap line

Planter Basket

8

10

9

7

11

6

12

5

1

4

2

3

Bore a 3” hole for a 3 1/2” O.D. clock insert.

.

Drill with a 1/16” bit and cut with table at 90° (flat). Roundover both edges 1/4” R.

Stock: 3/4” Top pattern piece

Frame

Pattern overlap line

Victorian Clock with Basket

Drill 1/8” pivot hole before sawing basket free. After routing 1/4” R countersink for #6 x 1 1/4” FH. screws.

Stock: 3/4” Bottom pattern piece

Frame

.

Drill a 1/16” hole to start bevel cut. Saw clockwide with table tilting down to the right at 5 1/2° or cut counterclockwise with table tilting down to the left at 5 1/2°.

Pattern overlap line

Victorian Clock with Basket

Victorian Clock with Basket

Base Stock: 3/4” Left pattern piece Drill and countersink bottomside for #9 x 1 1/2” FH screws.

Base Pattern overlap line

Stock: 3/4” Right pattern piece

Pattern overlap line

Roundover top edge 1/4” R.

Stock: 1/4”

Lid

Stock: 1/4”

Lid Support

Side

Cut on this line to separate Lid and Lid Support.

Side

Attach hinges of your choice.

Adjust slots, if necessary, for the thickness of material used.

Stock: 1/4”

Crest

Trinket Box

End

Side

Stock: 1/4”, cut 2

End

Trinket Box

Assembly Instructions Assemble by first attaching the Sides and Bottom to the Front. Then attach the Back. Attach Lid Support to top of Back with glue and #18 x 5/8” finshing nails. Next, secure the Lid to the Lid Support, and attach the Crest.

Stock: 1/4”, cut 1 each

Front & Back

Attach Bottom with nails and glue or silicone.

Stock: 1/4”

End

Bottom

End

Standing Mantle Clocks

Frame Stock: 3/4”

Bore 3" for 3 1/2” O.D. Clock insert.

3/4 "

1/4" R Typ.

1/4" x 1/4" rabbet

Rabbet backside for fretted insert.

Standing Mantle Clocks

11

12

1 2

10 3 9 4 8 7

6

5

Insert Stock: 1/4”

Insert Stock: 1/4”

Insert

Stock: 1/4” Stock: 3/4

Base

Drill and countersink bottomside for #7 x 1 1/2” FH screws.

Standing Mantle Clocks

Harley Silhouette

Attach Eagle and Trees to Frame with glue.

Right Tree Stock: 1/16” - 1/8” Spacers: 1/8”, cut 3

Left Tree Stock: 1/16” - 1/8” Spacers: 1/8”, cut 3

Eagle Stock: 1/16” - 1/8” Spacers: 1/8”, cut 3

Spacers

Harley Silhouette

Drill to hang.

Frame

Pattern overlap line

Stock: 1/4” Left pattern piece

Harley Silhouette

Frame

Pattern overlap line

Stock: 1/4” Right pattern piece

Fretted Box / Music Box

Foot

Front

Stock: 3/4”, cut 4 Top view.

Bottom Side / Lid Side

Bottom Front & Back / Lid Front & Back

Fold on dashed line Rear view

Back

1”

3

Side Trim

2

3/4

Foot Instructions 1. Attach pattern with repositionable spray adhesive. 2. Cut out rear shape 3. Cut out the top shape 4. Attach Foot with glue and finishing nails or silicone

Stock: 1/8”, cut 4

Top

1

Back

Roundover top edges by sanding.

Bottom Handle Stock: 1/4”

Stock: 1/8”, cut 4

Stock: 1/4”

Sand or cut ends 45°.

Top Handle Sand or cut ends 45°.

Stock: 1/4”. Attach to Lid with glue or silicone.

Front & Back Trim

Handle Support

Stock: 1/4”

Lid

Side

Side

Fretted Box

End

End

Stock: 1/4”

Bottom

End Side

Adjust slot, if necessary for the thickness of material

Assemble by first attaching the Sides to the Ends. Then secure this assembly to the Bottom. Attach the Lid support to the bottomside of the Lid, and then attach the Handle Support and Handle. Now attach the Feet with glue and finishing nails. Then attach the Front, Back and Side Trim. Finally, secure the music movement in place.

Assembly Instructions

Small dashed line indicates position of music movement

Drill 3/8” hole for key.

Side

Dashed line indicates placement of Foot.

Fretted Box

End

Fretted Box / Music Box

Side Stock: 1/4”, cut 2

Attach to End with glue and finishing nails.

End

Stock: 1/8” Attach to bottomside of Lid with glue or silicone.

Lid Support

Stock: 1/4”, cut 2

Stock: 1/8” - 1/4” Top pattern piece

Frame

Pattern overlap line

Moose Silhouette

Overlay

Stock: 1/16” - 1/8”, cut 4

Stock: 1/8” - 1/4” Bottom pattern piece

Frame

Pattern overlap line

Dashed lines indicate placement of Overlays.

Moose Silhouette

Pattern overlap line

Stock: 3/4" Top pattern piece

Frame

Stock: 3/4" Bottom pattern piece

Frame

Rabbet backside for fretted insert

1/4" x 1/4" Rabbet

1/4" R Typ.

Bore 2 3/8” for 2 3/4” O.D. clock insert.

8

10 9 7

11

Dashed line indicates placement of Insert on backside. Glue in place.

Pattern overlap line

6

12

5

1

4

2 3

Small Mantle Clocks

3/4"

Stock: 1/4”

Insert

Small Mantle Clocks

Stock: 1/4”

Insert

Small Mantle Clocks

Stock: 1/4”

Insert

Small Mantle Clocks

Stock: 3/4” Left pattern piece

Drill and countersink bottomside for #7 x 1 1/4” FH screws.

Roundover top edges 1/4” R

Base

Pattern overlap line Stock: 3/4” Right pattern piece

Base

Small Mantle Clocks Pattern overlap line

Mini Clock

Bore 1 3/8” hole for mini clock insert.

11

12

1 2

10 3 9 4 8 7

Frame Stock: 1/4" - 3/8"

Base Stock: 1/4" - 3/4" Use glue to attach Frame to Base.

6

5

Mini clock

11

12

1 2

10 3 9 4 8 7

6

5

Bore 1 3/8” hole for mini clock insert.

Frame Stock: 1/4” - 3/8”

Base Stock: 1/4” - 3/4” Use glue to attach Frame to Base

Mini clock

11

12

1 2

10 3 9 4 8 7

6

5

Bore 1 3/8” hole for mini clock insert.

Frame Stock: 1/4” - 3/8”

Base Stock: 1/4” - 3/4” Use glue to attach Frame to Base

Victorian Corner Shelf/Planter

Shelf Stock: 1/4”

Optional: Drill hole for a 3” pot.

Victorian Corner Shelf/Planter

Si

Sto de cut ck: 1/ 4”, 2

Ad thic just sl kne ot, i ss o f ne f m cess ater ary ial , for use d.

cut on 1 Sid this e line cut on 1 Sid this e line