Report 190
Electrospinning
Jon Stanger, Nick Tucker and Mark Staiger
Volume 16, Number 10, 2005
Expert overviews covering the science and technology of rubber and plastics
ISSN: 0889-3144
RAPRA REVIEW REPORTS A Rapra Review Report comprises three sections, as follows: 1. A commissioned expert review, discussing a key topic of current interest, and referring to the References and Abstracts section. Reference numbers in brackets refer to item numbers from the References and Abstracts section. Where it has been necessary for completeness to cite sources outside the scope of the Rapra Abstracts database, these are listed at the end of the review, and cited in the text as a.1, a.2, etc. 2. A comprehensive References and Abstracts section, resulting from a search of the Rapra Polymer Library database. The format of the abstracts is outlined in the sample record below. 3. An index to the References and Abstracts section, derived from the indexing terms which are added to the abstracts records on the database to aid retrieval.
Source of original article Title
Item 1 Macromolecules
33, No.6, 21st March 2000, p.2171-83 EFFECT OF THERMAL HISTORY ON THE RHEOLOGICAL BEHAVIOR OF THERMOPLASTIC POLYURETHANES Pil Joong Yoon; Chang Dae Han Akron,University The effect of thermal history on the rheological behaviour of ester- and etherbased commercial thermoplastic PUs (Estane 5701, 5707 and 5714 from B.F.Goodrich) was investigated. It was found that the injection moulding temp. used for specimen preparation had a marked effect on the variations of dynamic storage and loss moduli of specimens with time observed during isothermal annealing. Analysis of FTIR spectra indicated that variations in hydrogen bonding with time during isothermal annealing very much resembled variations of dynamic storage modulus with time during isothermal annealing. Isochronal dynamic temp. sweep experiments indicated that the thermoplastic PUs exhibited a hysteresis effect in the heating and cooling processes. It was concluded that the microphase separation transition or order-disorder transition in thermoplastic PUs could not be determined from the isochronal dynamic temp. sweep experiment. The plots of log dynamic storage modulus versus log loss modulus varied with temp. over the entire range of temps. (110-190C) investigated. 57 refs.
Location
GOODRICH B.F. USA
Authors and affiliation
Abstract
Companies or organisations mentioned
Accession no.771897
DOCUMENT DELIVERY SERVICE Almost all of the documents which are listed in the References and Abstracts section are available in full text form, as photocopies or pdf files from Smithers Rapra Technology’s Document Delivery Service. Documents can be delivered by a variety of methods, including email, post or fax. Customers may pay for individual copies at the time of ordering by credit card or alternatively open up a deposit account. See the back of this report for further information. Please contact the Document Delivery Department for availability, current prices and delivery methods. Document Delivery Department Smithers Rapra Technology, Shawbury, Shrewsbury, Shropshire SY4 4NR, United Kingdom Telephone: +44 (0)1939 250383 Fax: +44 (0)1939 251118 Email:
[email protected]
RAPRA REVIEW REPORTS VOLUME 16 Series Editor Mrs. F. Gardiner, Smithers Rapra Technology Rapra Review Reports comprise a unique source of polymer-related information with useful overviews accompanied by abstracts from hundreds of relevant documents. A Rapra Review Report is an excellent starting point to improve subject knowledge in key areas. Subscribers to this series build up a bank of information over each year, forming a small library at a very reasonable price. This series would be an asset to corporate libraries, academic institutions and research associations with an interest in polymer science. Twelve reports are published in each volume and these can be purchased individually or on a subscription basis. Format: Soft-backed, 297 x 210 mm, ISSN: 0889-3144 Order individual published Rapra Review Reports (see the following pages for a list of available titles), or purchase a subscription to Volume 16 (12 issues).
ORDER FORM Title of Publication
Price £/$/`
I would like to order the following Rapra Review Report(s) at £85 / US$136 / `136 each Report Number(s) ....................................................................................................(please state quantity if more than one) Please add postage at the following rates: UK £5 total, Overseas £7 / US$11 / `10 per item Subtotal: I would like to order ................. subscription(s) to Volume 16 of the Rapra Review Report Series at £650 / US$975 / `1105 each Please add postage at the following rates: UK £35 total, Overseas £65 / US$110 / `110 per subscription All prices are subject to change and orders will be charged at the price indicated on www.polymer-books.com on the date of processing
enclosed (Please make cheques payable to Rapra Technology in Q Remittance £ Sterling drawn on a UK bank or in US$ / Euros - Unesco coupons are also accepted.)
Q Please invoice my company Q Please charge my credit card American Express/Visa/Mastercard (delete as appropriate) For credit card orders we require all of the following details to be completed prior to processing your order.
Total Order Value:
IMPORTANT - Value Added Tax (VAT) The above prices do not include VAT. Customers in EU member countries may be liable to pay VAT if their Registration Number is not supplied. Please enter your EU Registration Number (VAT - BTW - IVA - TVA - MWST - MOMS - FPA) below: VAT Number:
Card Number:
Full Name: ________________________________________________ Please enter the cards security code below, or provide us with your telephone number or email address. (Visa/Mastercard - the last 3 digits from the number on the signature strip on the back of the card, Amex - 4 digit code from the front of the card.) 3 or 4 Digit Security Code: ____________
Signature: ______________________ Exp. date:__________________ Issuing Bank: ______________________________________________ Cardholder's Name (as on card): ________________________________
Company: _________________________________________________ Job Function:_______________________________________________ Delivery Address (if different from Cardholder's Address): ___________ __________________________________________________________ __________________________________________________________
Cardholder's Address: ________________________________________ __________________________________________________________ __________________________________________________________ Postcode: _______________________ Country:___________________ Telephone: ______________________ Fax: ______________________ Company PO#: _____________________________________________
Please Return to:
Publications Sales, Smithers Rapra Technology Shawbury, Shrewsbury, Shropshire SY4 4NR, United Kingdom
Postcode: _______________________ Country:___________________ Telephone: ______________________ Fax: ______________________ If you would like to receive regular electronic updates informing you of new titles and offers please enter your E-mail address below. E-mail:____________________________________________________ Tel. +44 (0)1939 250383 Fax: +44 (0)1939 251118 E-mail:
[email protected]
www.rapra.net
Previous Titles Still Available Volume 1
Report 34
Extrusion of Rubber, J.G.A. Lovegrove, Nova Petrochemicals Inc.
Report 1
Conductive Polymers, W.J. Feast
Report 35
Report 2
Medical, Surgical and Pharmaceutical Applications of Polymers, D.F. Williams
Polymers in Household Electrical Goods, D.Alvey, Hotpoint Ltd.
Report 36
Report 3
Advanced Composites, D.K. Thomas, RAE, Farnborough.
Developments in Additives to Meet Health and Environmental Concerns, M.J. Forrest, Rapra Technology Ltd.
Report 4
Liquid Crystal Polymers, M.K. Cox, ICI, Wilton.
Report 5
CAD/CAM in the Polymer Industry, N.W. Sandland and M.J. Sebborn, Cambridge Applied Technology.
Report 8
Engineering Thermoplastics, I.T. Barrie, Consultant.
Report 10
Reinforced Reaction Injection Moulding, P.D. Armitage, P.D. Coates and A.F. Johnson
Report 11
Communications Applications of Polymers, R. Spratling, British Telecom.
Report 12
Process Control in the Plastics Industry, R.F. Evans, Engelmann & Buckham Ancillaries.
Volume 2
Volume 4 Report 37
Polymers in Aerospace Applications, W.W. Wright, University of Surrey.
Report 38
Epoxy Resins, K.A. Hodd
Report 39
Polymers in Chemically Resistant Applications, D. Cattell, Cattell Consultancy Services.
Report 40
Internal Mixing of Rubber, J.C. Lupton
Report 41
Failure of Plastics, S. Turner, Queen Mary College.
Report 42
Polycarbonates, R. Pakull, U. Grigo, D. Freitag, Bayer AG.
Report 43
Polymeric Materials from Renewable Resources, J.M. Methven, UMIST.
Report 13
Injection Moulding of Engineering Thermoplastics, A.F. Whelan, London School of Polymer Technology.
Report 44
Report 14
Polymers and Their Uses in the Sports and Leisure Industries, A.L. Cox and R.P. Brown, Rapra Technology Ltd.
Flammability and Flame Retardants in Plastics, J. Green, FMC Corp.
Report 45
Composites - Tooling and Component Processing, N.G. Brain, Tooltex.
Report 15
Polyurethane, Materials, Processing and Applications, G. Woods, Consultant.
Report 46
Quality Today in Polymer Processing, S.H. Coulson, J.A. Cousans, Exxon Chemical International Marketing.
Report 16
Polyetheretherketone, D.J. Kemmish, ICI, Wilton.
Report 47
Report 17
Extrusion, G.M. Gale, Rapra Technology Ltd.
Chemical Analysis of Polymers, G. Lawson, Leicester Polytechnic.
Report 18
Agricultural and Horticultural Applications of Polymers, J.C. Garnaud, International Committee for Plastics in Agriculture.
Report 48
Plastics in Building, C.M.A. Johansson
Report 19
Recycling and Disposal of Plastics Packaging, R.C. Fox, Plas/Tech Ltd.
Report 20
Pultrusion, L. Hollaway, University of Surrey.
Report 21
Materials Handling in the Polymer Industry, H. Hardy, Chronos Richardson Ltd.
Report 22
Electronics Applications of Polymers, M.T.Goosey, Plessey Research (Caswell) Ltd.
Report 23
Offshore Applications of Polymers, J.W.Brockbank, Avon Industrial Polymers Ltd.
Report 24
Recent Developments in Materials for Food Packaging, R.A. Roberts, Pira Packaging Division.
Volume 3
Volume 5 Report 49
Blends and Alloys of Engineering Thermoplastics, H.T. van de Grampel, General Electric Plastics BV.
Report 50
Automotive Applications of Polymers II, A.N.A. Elliott, Consultant.
Report 51
Biomedical Applications of Polymers, C.G. Gebelein, Youngstown State University / Florida Atlantic University.
Report 52
Polymer Supported Chemical Reactions, P. Hodge, University of Manchester.
Report 53
Weathering of Polymers, S.M. Halliwell, Building Research Establishment.
Report 54
Health and Safety in the Rubber Industry, A.R. Nutt, Arnold Nutt & Co. and J. Wade.
Report 55
Computer Modelling of Polymer Processing, E. Andreassen, Å. Larsen and E.L. Hinrichsen, Senter for Industriforskning, Norway.
Report 25
Foams and Blowing Agents, J.M. Methven, Cellcom Technology Associates.
Report 26
Polymers and Structural Composites in Civil Engineering, L. Hollaway, University of Surrey.
Report 56
Plastics in High Temperature Applications, J. Maxwell, Consultant.
Report 27
Injection Moulding of Rubber, M.A. Wheelans, Consultant.
Report 57
Joining of Plastics, K.W. Allen, City University.
Report 58
Physical Testing of Rubber, R.P. Brown, Rapra Technology Ltd.
Report 59
Polyimides - Materials, Processing and Applications, A.J. Kirby, Du Pont (U.K.) Ltd.
Report 60
Physical Testing of Thermoplastics, S.W. Hawley, Rapra Technology Ltd.
Report 28
Adhesives for Structural and Engineering Applications, C. O’Reilly, Loctite (Ireland) Ltd.
Report 29
Polymers in Marine Applications, C.F.Britton, Corrosion Monitoring Consultancy.
Report 30
Non-destructive Testing of Polymers, W.N. Reynolds, National NDT Centre, Harwell.
Report 31
Silicone Rubbers, B.R. Trego and H.W.Winnan, Dow Corning Ltd.
Volume 6
Report 32
Fluoroelastomers - Properties and Applications, D. Cook and M. Lynn, 3M United Kingdom Plc and 3M Belgium SA.
Report 61
Food Contact Polymeric Materials, J.A. Sidwell, Rapra Technology Ltd.
Report 62
Coextrusion, D. Djordjevic, Klöckner ER-WE-PA GmbH.
Polyamides, R.S. Williams and T. Daniels, T & N Technology Ltd. and BIP Chemicals Ltd.
Report 63
Conductive Polymers II, R.H. Friend, University of Cambridge, Cavendish Laboratory.
Report 33
Report 64
Designing with Plastics, P.R. Lewis, The Open University.
Report 90
Rubber Mixing, P.R. Wood.
Report 65
Decorating and Coating of Plastics, P.J. Robinson, International Automotive Design.
Report 91
Recent Developments in Epoxy Resins, I. Hamerton, University of Surrey.
Report 66
Reinforced Thermoplastics - Composition, Processing and Applications, P.G. Kelleher, New Jersey Polymer Extension Center at Stevens Institute of Technology.
Report 92
Continuous Vulcanisation of Elastomer Profiles, A. Hill, Meteor Gummiwerke.
Report 67
Plastics in Thermal and Acoustic Building Insulation, V.L. Kefford, MRM Engineering Consultancy.
Report 93
Advances in Thermoforming, J.L. Throne, Sherwood Technologies Inc.
Report 68
Cure Assessment by Physical and Chemical Techniques, B.G. Willoughby, Rapra Technology Ltd.
Report 94
Compressive Behaviour of Composites, C. Soutis, Imperial College of Science, Technology and Medicine.
Report 69
Toxicity of Plastics and Rubber in Fire, P.J. Fardell, Building Research Establishment, Fire Research Station.
Report 95
Thermal Analysis of Polymers, M. P. Sepe, Dickten & Masch Manufacturing Co.
Report 70
Acrylonitrile-Butadiene-Styrene Polymers, M.E. Adams, D.J. Buckley, R.E. Colborn, W.P. England and D.N. Schissel, General Electric Corporate Research and Development Center.
Report 96
Polymeric Seals and Sealing Technology, J.A. Hickman, St Clair (Polymers) Ltd.
Report 71
Rotational Moulding, R.J. Crawford, The Queen’s University of Belfast.
Report 72
Advances in Injection Moulding, C.A. Maier, Econology Ltd.
Volume 7 Report 73
Reactive Processing of Polymers, M.W.R. Brown, P.D. Coates and A.F. Johnson, IRC in Polymer Science and Technology, University of Bradford.
Volume 9 Report 97
Rubber Compounding Ingredients - Need, Theory and Innovation, Part II: Processing, Bonding, Fire Retardants, C. Hepburn, University of Ulster.
Report 98
Advances in Biodegradable Polymers, G.F. Moore & S.M. Saunders, Rapra Technology Ltd.
Report 99
Recycling of Rubber, H.J. Manuel and W. Dierkes, Vredestein Rubber Recycling B.V.
Report 100
Photoinitiated Polymerisation - Theory and Applications, J.P. Fouassier, Ecole Nationale Supérieure de Chimie, Mulhouse.
Report 74
Speciality Rubbers, J.A. Brydson.
Report 75
Plastics and the Environment, I. Boustead, Boustead Consulting Ltd.
Report 101
Solvent-Free Adhesives, T.E. Rolando, H.B. Fuller Company.
Report 76
Polymeric Precursors for Ceramic Materials, R.C.P. Cubbon.
Report 102
Plastics in Pressure Pipes, T. Stafford, Rapra Technology Ltd.
Report 77
Advances in Tyre Mechanics, R.A. Ridha, M. Theves, Goodyear Technical Center.
Report 103
Gas Assisted Moulding, T.C. Pearson, Gas Injection Ltd.
Report 104
Plastics Profile Extrusion, R.J. Kent, Tangram Technology Ltd.
Report 105
Rubber Extrusion Theory and Development, B.G. Crowther.
Report 106
Properties and Applications of Elastomeric Polysulfides, T.C.P. Lee, Oxford Brookes University.
Report 107
High Performance Polymer Fibres, P.R. Lewis, The Open University.
Report 108
Chemical Characterisation of Polyurethanes, M.J. Forrest, Rapra Technology Ltd.
Report 78
PVC - Compounds, Processing and Applications, J.Leadbitter, J.A. Day, J.L. Ryan, Hydro Polymers Ltd.
Report 79
Rubber Compounding Ingredients - Need, Theory and Innovation, Part I: Vulcanising Systems, Antidegradants and Particulate Fillers for General Purpose Rubbers, C. Hepburn, University of Ulster.
Report 80
Anti-Corrosion Polymers: PEEK, PEKK and Other Polyaryls, G. Pritchard, Kingston University.
Report 81
Thermoplastic Elastomers - Properties and Applications, J.A. Brydson.
Report 82
Advances in Blow Moulding Process Optimization, Andres Garcia-Rejon,Industrial Materials Institute, National Research Council Canada.
Volume 10 Report 109
Rubber Injection Moulding - A Practical Guide, J.A. Lindsay.
Report 110
Long-Term and Accelerated Ageing Tests on Rubbers, R.P. Brown, M.J. Forrest and G. Soulagnet, Rapra Technology Ltd.
Report 111
Polymer Product Failure, P.R. Lewis, The Open University.
Report 112
Ring Opening Polymerisation, N. Spassky, Université Pierre et Marie Curie.
Polystyrene - Synthesis, Production and Applications, J.R. Wünsch, BASF AG.
Report 113
High Performance Engineering Plastics, D.J. Kemmish, Victrex Ltd.
Rubber-Modified Thermoplastics, H. Keskkula, University of Texas at Austin.
Report 114
Report 87
Rubber to Metal Bonding, B.G. Crowther, Rapra Technology Ltd.
Developments in Polyacetylene - Nanopolyacetylene, V.M. Kobryanskii, Russian Academy of Sciences.
Report 115
Report 88
Plasticisers - Selection, Applications and Implications, A.S. Wilson.
Metallocene-Catalysed Polymerisation, W. Kaminsky, University of Hamburg.
Report 116
Report 89
Polymer Membranes - Materials, Structures and Separation Performance, T. deV. Naylor, The Smart Chemical Company.
Compounding in Co-rotating Twin-Screw Extruders, Y. Wang, Tunghai University.
Report 117
Rapid Prototyping, Tooling and Manufacturing, R.J.M. Hague and P.E. Reeves, Edward Mackenzie Consulting.
Report 83
Report 84
Molecular Weight Characterisation of Synthetic Polymers, S.R. Holding and E. Meehan, Rapra Technology Ltd. and Polymer Laboratories Ltd. Rheology and its Role in Plastics Processing, P. Prentice, The Nottingham Trent University.
Volume 8 Report 85 Report 86
Report 118
Liquid Crystal Polymers - Synthesis, Properties and Applications, D. Coates, CRL Ltd.
Report 119
Rubbers in Contact with Food, M.J. Forrest and J.A. Sidwell, Rapra Technology Ltd.
Report 120
Electronics Applications of Polymers II, M.T. Goosey, Shipley Ronal.
Volume 11 Report 121
Polyamides as Engineering Thermoplastic Materials, I.B. Page, BIP Ltd.
Report 122
Flexible Packaging - Adhesives, Coatings and Processes, T.E. Rolando, H.B. Fuller Company.
Report 123
Polymer Blends, L.A. Utracki, National Research Council Canada.
Report 124
Sorting of Waste Plastics for Recycling, R.D. Pascoe, University of Exeter.
Report 125
Structural Studies of Polymers by Solution NMR, H.N. Cheng, Hercules Incorporated.
Volume 13 Report 145
Multi-Material Injection Moulding, V. Goodship and J.C. Love, The University of Warwick.
Report 146
In-Mould Decoration of Plastics, J.C. Love and V. Goodship, The University of Warwick.
Report 147
Rubber Product Failure, Roger P. Brown.
Report 148
Plastics Waste – Feedstock Recycling, Chemical Recycling and Incineration, A. Tukker, TNO.
Report 149
Analysis of Plastics, Martin J. Forrest, Rapra Technology Ltd.
Report 150
Mould Sticking, Fouling and Cleaning, D.E. Packham, Materials Research Centre, University of Bath.
Report 151
Rigid Plastics Packaging - Materials, Processes and Applications, F. Hannay, Nampak Group Research & Development.
Report 152
Natural and Wood Fibre Reinforcement in Polymers, A.K. Bledzki, V.E. Sperber and O. Faruk, University of Kassel.
Report 153
Polymers in Telecommunication Devices, G.H. Cross, University of Durham.
Report 154
Polymers in Building and Construction, S.M. Halliwell, BRE.
Report 126
Composites for Automotive Applications, C.D. Rudd, University of Nottingham.
Report 127
Polymers in Medical Applications, B.J. Lambert and F.-W. Tang, Guidant Corp., and W.J. Rogers, Consultant.
Report 155
Styrenic Copolymers, Andreas Chrisochoou and Daniel Dufour, Bayer AG.
Report 128
Solid State NMR of Polymers, P.A. Mirau, Lucent Technologies.
Report 156
Life Cycle Assessment and Environmental Impact of Polymeric Products, T.J. O’Neill, Polymeron Consultancy Network.
Report 129
Failure of Polymer Products Due to Photo-oxidation, D.C. Wright.
Report 130
Failure of Polymer Products Due to Chemical Attack, D.C. Wright.
Report 131 Report 132
Failure of Polymer Products Due to Thermo-oxidation, D.C. Wright. Stabilisers for Polyolefins, C. Kröhnke and F. Werner, Clariant Huningue SA.
Volume 12
Volume 14 Report 157
Developments in Colorants for Plastics, Ian N. Christensen.
Report 158
Geosynthetics, David I. Cook.
Report 159
Biopolymers, R.M. Johnson, L.Y. Mwaikambo and N. Tucker, Warwick Manufacturing Group.
Report 160
Emulsion Polymerisation and Applications of Latex, Christopher D. Anderson and Eric S. Daniels, Emulsion Polymers Institute.
Report 161
Emissions from Plastics, C. Henneuse-Boxus and T. Pacary, Certech.
Report 133
Advances in Automation for Plastics Injection Moulding, J. Mallon, Yushin Inc.
Report 162
Analysis of Thermoset Materials, Precursors and Products, Martin J. Forrest, Rapra Technology Ltd.
Report 134
Infrared and Raman Spectroscopy of Polymers, J.L. Koenig, Case Western Reserve University.
Report 163
Polymer/Layered Silicate Nanocomposites, Masami Okamoto, Toyota Technological Institute.
Report 135
Polymers in Sport and Leisure, R.P. Brown.
Report 164
Report 136
Radiation Curing, R.S. Davidson, DavRad Services.
Cure Monitoring for Composites and Adhesives, David R. Mulligan, NPL.
Report 165
Report 137
Silicone Elastomers, P. Jerschow, Wacker-Chemie GmbH.
Polymer Enhancement of Technical Textiles, Roy W. Buckley.
Report 138
Health and Safety in the Rubber Industry, N. Chaiear, Khon Kaen University.
Report 166
Developments in Thermoplastic Elastomers, K.E. Kear
Report 167 Report 139
Rubber Analysis - Polymers, Compounds and Products, M.J. Forrest, Rapra Technology Ltd.
Polyolefin Foams, N.J. Mills, Metallurgy and Materials, University of Birmingham.
Report 168
Report 140
Tyre Compounding for Improved Performance, M.S. Evans, Kumho European Technical Centre.
Plastic Flame Retardants: Technology and Current Developments, J. Innes and A. Innes, Flame Retardants Associates Inc.
Report 141
Particulate Fillers for Polymers, Professor R.N. Rothon, Rothon Consultants and Manchester Metropolitan University.
Report 142
Blowing Agents for Polyurethane Foams, S.N. Singh, Huntsman Polyurethanes.
Report 143
Adhesion and Bonding to Polyolefins, D.M. Brewis and I. Mathieson, Institute of Surface Science & Technology, Loughborough University.
Report 144
Rubber Curing Systems, R.N. Datta, Flexsys BV.
Volume 15 Report 169
Engineering and Structural Adhesives, David J. Dunn, FLD Enterprises Inc.
Report 170
Polymers in Agriculture and Horticulture, Roger P. Brown.
Report 171
PVC Compounds and Processing, Stuart Patrick.
Report 172
Troubleshooting Injection Moulding, Vanessa Goodship, Warwick Manufacturing Group.
Report 173
Regulation of Food Packaging in Europe and the USA, Derek J. Knight and Lesley A. Creighton, Safepharm Laboratories Ltd.
Report 174
Pharmaceutical Applications of Polymers for Drug Delivery, David Jones, Queen's University, Belfast.
Report 175
Tyre Recycling, Valerie L. Shulman, European Tyre Recycling Association (ETRA).
Report 176
Polymer Processing with Supercritical Fluids, V. Goodship and E.O. Ogur.
Report 177
Bonding Elastomers: A Review of Adhesives & Processes, G. Polaski, J. Means, B. Stull, P. Warren, K. Allen, D. Mowrey and B. Carney.
Report 178
Mixing of Vulcanisable Rubbers and Thermoplastic Elastomers, P.R. Wood.
Report 179
Polymers in Asphalt, H.L. Robinson, Tarmac Ltd, UK.
Report 180
Biocides in Plastics, D. Nichols, Thor Overseas Limited.
Volume 16 Report 181
New EU Regulation of Chemicals: REACH, D.J. Knight, SafePharm Laboratories Ltd.
Report 182
Food Contact Rubbers 2 - Products, Migration and Regulation, M.J. Forrest.
Report 183
Adhesion to Fluoropolymers, D.M. Brewis and R.H. Dahm, IPTME, Loughborough University.
Report 184
Fluoroplastics, J.G. Drobny.
Report 185
Epoxy Composites: Impact Resistance and Flame Retardancy, Debdatta Ratna.
Report 186
Coatings and Inks for Food Contact Materials, Martin Forrest, Smithers Rapra.
Report 187
Nucleating Agents, Stuart Fairgrieve, SPF Polymer Consultants.
Report 188
Silicone Products for Food Contact Applications, Martin Forrest, Smithers Rapra.
Report 189
Degradation and Stabilisation of Polymers, Stuart Fairgrieve, SPF Polymer Consultants
Electrospinning
Jon Stanger, Nick Tucker and Mark Staiger
ISBN: 978-1-84735-091-6
Electrospinning
Contents 1.
2.
Electrospinning Development ....................................................................................................................3 1.1
Early Electrospinning (1600-1995)..................................................................................................3
1.2
Recent History (1995-present) .........................................................................................................5
Background Theory ....................................................................................................................................6 2.1
2.2
3.
Polymer Solutions ............................................................................................................................6 2.1.1
Intermolecular and Solute/Solvent Interactions in Polymers..............................................6
2.1.2
Viscoelasticity .....................................................................................................................6
2.1.3
Surface Tension...................................................................................................................7
2.1.4
Conductivity ........................................................................................................................8
External Forces ................................................................................................................................8 2.2.1
Electrodynamic Force .........................................................................................................8
2.2.2
Surface Charge ....................................................................................................................9
2.2.3
Fluid Pressure......................................................................................................................9
Electrospinning Processes and Apparatus ...............................................................................................10 3.1
3.2
3.3
Simple Process Description ...........................................................................................................10 3.1.1
Axis Conventions ..............................................................................................................10
3.1.2
Basic Physics of Electrospinning ......................................................................................10
Process Models ..............................................................................................................................11 3.2.1
Jet Initiation.......................................................................................................................11
3.2.2
Jet Thinning.......................................................................................................................12
3.2.3
Fluid Instabilities ..............................................................................................................13
3.2.4
Bending Instability ............................................................................................................14
3.2.5
Polymer Chain Alignment ................................................................................................15
Process Parameters.........................................................................................................................15 3.3.1
Solution Parameters ..........................................................................................................16
3.3.2
Processing Variables .........................................................................................................16
3.3.3
Environmental Conditions ................................................................................................17
3.4
Core Apparatus ..............................................................................................................................17
3.5
Modifications and Additions to Core Apparatus ...........................................................................19 3.5.1
Polymer Supply Modifications .........................................................................................19
3.5.2
Electrostatic Field Modifications ......................................................................................19
3.5.3
Collector Modifications.....................................................................................................19
1
Electrospinning
4.
5.
Applications .............................................................................................................................................20 4.1
Nanoscale Materials .......................................................................................................................20
4.2
High Tensile Strength Fibres .........................................................................................................21
4.3
Surface Area to Volume Ratio .......................................................................................................21
4.4
Medical Applications .....................................................................................................................22
4.5
Materials Applications ...................................................................................................................22
4.6
Industrial Applications ...................................................................................................................23
4.7
Electronics and Energy Applications .............................................................................................24
Materials ...................................................................................................................................................25
References ........................................................................................................................................................28 Abstracts from the Polymer Library Database.................................................................................................35 Subject Index .................................................................................................................................................187 Company Index ..............................................................................................................................................201
Author contact details: Jon Stanger The New Zealand Institute for Plant and Food Research
[email protected] Nick Tucker The New Zealand Institute for Plant and Food Research
[email protected] Mark Staiger Department of Mechanical Engineering, University of Canterbury, New Zealand
[email protected]
The views and opinions expressed by authors in Rapra Review Reports do not necessarily reflect those of Smithers Rapra Technology or the editor. The series is published on the basis that no responsibility or liability of any nature shall attach to Smithers Rapra Technology arising out of or in connection with any utilisation in any form of any material contained therein.
2
Electrospinning
1 ELECTROSPINNING DEVELOPMENT 1.1 Early Electrospinning (1600-1995) In the late 1500s William Gilbert set out to describe the behaviour of magnetic and electrostatic phenomena. His work [a.1] is an early example of what would become the modern scientific method. He received funding from Queen Elizabeth I, whereupon he moved to London, caught bubonic plague, and passed away. He had, however, already distinguished between the magnetic forces arising from a lodestone (natural magnet) and the electrostatic forces arising from rubbed amber. One of his more obscure observations was that when a suitably charged piece of amber was brought near a droplet of water it would form a cone shape and small droplets would be ejected from the tip of the cone - the first recorded observation of electrospraying. The first description of a process recognisable as electrospinning was in 1902 when J. F. Cooley filed a United States patent entitled ‘Apparatus for electrically dispersing fibres’ [a.2]. In his patent (US 692631) he describes a method of using high voltage power supplies to generate yarn. Even at this early stage it was recognised that to form fibres rather than droplets the (i) fluid must be sufficiently viscous, (ii) solvent volatile enough to evaporate to allow regeneration of the solid polymer, and (iii) electric field strength within a certain range.
The next significant academic development was achieved by John Zeleny, who published work on the behaviour of fluid droplets at the end of metal capillaries in 1914 [a.3]. His work began the efforts to mathematically model the behaviour of fluids under electrostatic forces. Between 1964 and 1969, Sir Geoffrey Ingram Taylor produced the theoretical underpinning of electrospinning [a.4-a.6]. Taylor’s work on electrostatics was performed during his retirement after a broad career including modelling of turbulent mixing of air at the Arctic, significant contributions to the fields of fluid mechanics and solid mechanics via work on the Manhattan Project and development of supersonic aircraft. Taylor’s work contributed to electrospinning by mathematically modelling the shape of the cone formed by the fluid droplet under the effect of an electric field; this characteristic droplet shape is now known as the Taylor cone. He further worked with J.R. Melcher to develop the ‘leaky dielectric model’ for conducting fluids [a.7]. In parallel to the academic work of Zeleny and Taylor came a sequence of patents (Table 1), starting with the design by Cooley who separated the charging device from the spinning head [a.2]. In the same year, Morton patented a simpler low-throughput machine [a.8]. Melt spinning and air-blast assist were proposed by Norton [a.9] then a sequence of constant pressure feed high-throughput machines by Anton Formhals was filed between 1934 and 1944 [a.10-a.16] to produce continuous fine fibres for use on standard textile machinery. Gladding also proposed the use of the process to produce staple (discontinuous fibres) [a.17].
Table 1 Patents issued for electrospinning between 1902 and 1992. Patent Number
Date
Holder
Title
US 692631
February, 1902
J.F. Cooley
Apparatus for electrically dispersing fluids [a.2]
US 705691
July, 1902
W.J. Morton
Method of dispersing fluids [a.8]
US 745276
November, 1903
J.F. Cooley
Electrical method of dispersing fluids
US 1975504
October, 1934
A. Formhals
Process and apparatus for preparing artificial threads [a.10]
US 2048651
July, 1936
C.L. Norton
Method of and apparatus for producing fibrous or filamentary material [a.9]
US 2109333
February, 1938
A. Formhals
Artificial fibre construction [a.11]
US 2158415
May, 1939
A. Formhals
Method of producing artificial fibres [a.13]
US 2160962
June, 1939
A. Formhals
Method and apparatus for spinning [a.12]
US 2168027
August, 1939
E.K. Gladding
Apparatus for the production of filaments, threads, and the like [a.17]
US 2187306
January, 1940
A. Formhals
Artificial thread and method of producing same [a.14]
US 2185417
January, 1940
C.L. Norton
Method and apparatus for forming fibrous material
3
Electrospinning
US 2323025
June, 1943
A. Formhals
Production of artificial fibres from fiber forming liquids [a.15]
US 2338570
January, 1944
H.R. Childs
Process of electrostatic spinning
US 2349950
May, 1944
A. Formhals
Method and apparatus for spinning [a.16]
US 2636216
April, 1953
W.C. Huebner
Method and means of producing threads or filaments electrically
US 2908545
October 1959
J.D. Teja
Spinning nonfused glass fibres from an aqueous dispersion
US 3280229
October, 1966
H.L. Simons
Process and apparatus for producing patterned non-woven fabrics
US 3475198
October, 1969
E.W. Drum
Method and apparatus for applying a binder material to a prearranged web of unbound, non-woven fibres by electrostatic attraction
US 3490115
January, 1970
J.E. Owens and S.P. Scheinberg
Apparatus for collecting charged fibrous material in sheet form
US 3670486
June, 1972
G.L. Murray, Jr.
Electrostatic spinning head funnel
US 3689608
September, 1972
H.J. Hollberg and J.E. Owens
Process for forming a non-woven web
US 3901012
August, 1975
V. Safar
Method of and device for processing fibrous material
US 3994258
November, 1976
W. Simm
Apparatus for the production of filters by electrostatic fiber spinning
US 4044404
August, 1977
G.E. Martin, I.D. Cockshott and F.J.T. Fildes
Fibrillar lining for prosthetic device
US 4127706
November, 1978
G.E. Martin, I.D. Cockshott and K.T. McAloon
Porous fluoropolymeric fibrous sheet and method of manufacture
US 4230650
October, 1980
C. Guignard
Process for the manufacture of a plurality of filaments
US 4323525
April, 1982
A. Bornat
Electrostatic spinning of tubular products
US 4345414
August, 1982
A. Bornat and R.M. Clarke
Shaping process
US 4468922
September, 1984
P.E. McCrady and R.B. Reif
Apparatus for spinning textile fibres
US 4486365
December, 1984
B. Kliemann and M. Stoll
Process and apparatus for the preparation of electret filaments, textile fibres and similar articles
US 4552707
November, 1985
T.V. How
Synthetic vascular grafts, and methods of manufacturing such grafts
US 4618524
October, 1986
D. Groitzsch and E. Fahrbach
Microporous multilayer non-woven material for medical applications
US 4689186
August, 1987
A. Bornat
Production of electrostatically spun products
US 4878908
November, 1989
G.E. Martin and I.D. Cockshott and F.J.T. Fildes
Fibrillar product
US 4965110
October, 1990
J.P. Berry
Electrostatically produced structures and methods of manufacturing
US 5024789
June, 1991
J.P. Berry
Method and apparatus for manufacturing electrostatically spun structure
US 5088807
February, 1992
C.M. Waters, T.J. Noales, Liquid crystal devices I. Pavey and C. Hitomi
4
Electrospinning
1.2 Recent History (1995-present) Electrospinning was re-discovered in 1995 in the form of a potential source of nano-structured material by Doshi and Reneker who, whilst investigating electrospraying, observed that fibres could easily be formed with diameters on the nanometre scale [a.18]. Huang and co-workers noted that between 1995 and 2000 fewer than 10 journal papers were published annually, but from 2000 onwards the number of papers per year grew, reaching over 50 by 2002 and reflecting the growing interest in electrospinning by, at least, the academic community [a.19]. Since 1995 there have been further theoretical developments of the driving mechanisms of the electrospinning process. Reznik and co-workers describe extensive work on the shape of the Taylor cone and the subsequent ejection of a fluid jet [a.20]. The work by Hohman and co-workers investigates the relative growth rates of the numerous proposed instabilities in an electrically forced jet once in flight [a.21]. Also important has been the work by Yarin and co-workers that endeavours to describe the most
important instability to the electrospinning process, the bending (whipping) instability [a.22]. Using the keyword ‘electrospinning’ for a search in a scientific database (Compendex and Inspec) returns about 3,200 papers (Search performed 25/11/08, range 1884-2008). The term ‘electrospinning’ was first coined in 1995 by Doshi and Reneker. Figure 1 demonstrates the recent strong growth in this area by plotting the number of scientific papers on the subject published per year. The figure also shows which countries are most active in electrospinning research. Use of the same keyword for a search of a patent database returns about 1,460 documents at the time of writing (2006 being the last year for which complete figures are available). Performing the same search limited to the years 20042008 returns about 1,000 documents. These numbers show how the commercial environment surrounding the electrospinning process is currently something of a patent ‘storm’. Given that there are only a small handful of companies that produce electrospinning apparatus or electrospun products, there is a need for focused electrospinning research on specific applications.
Number of papers published with the keyword 'Electrospinning' in a given year
5
Electrospinning
Country of origin for papers containing the keyword 'Electrospinning'
Figure 1 Breakdown of journal papers with the keyword ‘Electrospinning’ broken down by publication year and country of origin (Numbers obtained 25/11/2008)
2 BACKGROUND THEORY 2.1 Polymer Solutions 2.1.1 Intermolecular and Solute/Solvent Interactions in Polymers A polymer molecule can be thought of as having a structure analogous to a coiled ball of string. This conformation (the 3D structure of a molecule) is due to the tetrahedral nature of the carbon atoms that form the backbone of most polymers. A collection of these balls where the coils are entangled represents the amorphous (random molecular orientation) state of a polymer as opposed to the crystalline state in which the molecules are more ordered. In a solvent a polymer will open up its coil or separate from the crystal surface, allowing solvent molecules to surround the chain. The extent to which this occurs depends on the solvent-polymer interaction. If there is poor interaction the polymer will not dissolve and is simply dispersed. If the interaction is strong then the coil will be very open due to a significant number of solvent molecules surrounding the chain. If the solvent-polymer interaction is equal to that of the intramolecular interaction (interaction between different parts of the same molecule) then the resulting solution is known as an ideal solution. A polymer melt can also be thought of as an ideal solution since the ‘solvent’
6
is simply other polymer molecules of the same type. For a polymer solution to electrospin there must be a sufficient degree of intramolecular interaction to cope with the tensile forces associated with the process of fibre drawing.
2.1.2 Viscoelasticity In order to talk about a bulk material property such as viscoelasticity, one first needs to define the quantities of normal stress, shear stress and strain. Stress in one dimension is the force exerted (F) divided by the area (A) (see Equation 1). Normal stress (often shortened to simply ‘stress’) is force applied perpendicular to the face of the material, whereas a shear stress involves a force parallel to the face of the material. Strain is the change in length per unit length (see Equation 2 where Dl is the change in length and l is the total length). Viscoelasticity describes the behaviour of a material that is both viscous and elastic under stress, so it has properties of both the solid and the liquid phase. A viscous material will undergo viscous flow to relieve the application of shear stress as described by Newton’s law (see Equation 3). This behaviour can be modelled with a dashpot which is a loosely fitting piston in a cylinder containing a fluid of viscosity H (see Figure 2). A perfectly elastic material obeys Hooke’s law (see Equation 4 where E is the elastic modulus) and hence behaves like a perfect spring. As such this behaviour could be modelled by a
Electrospinning
perfect spring which acts as an energy storage element, gaining energy with extension and releasing it when the material returns to its original shape.
Equation 3
Equation 4
Equation 5
2.1.3 Surface Tension Figure 2 Diagram of a dashpot with a fluid of viscosity H.
The combination of a viscous and an elastic behaviour, as shown by polymers and polymer solutions, becomes more complicated. The stress strain behaviour shows elements that obey Hooke’s law, but unlike an elastic response the viscous response acts to dissipate energy as heat, resulting in hysteresis and creep. Hysteresis is due to the viscous response causing the loss of energy, meaning that the material cannot return to its original shape. Creep is the tendency of a material to slowly deform under continuous stress below the yield strength in order to relieve the applied stress. One of the first models of viscoelastic behaviour was the Maxwell model. The Maxwell model assumes that the contribution to the stain from the elastic and viscous behaviour is additive (i.e., E = Eelast + Evisco). As such, mathematically it represents a spring element in series with a dashpot element. Another early model was the Voigt-Kelvin model. This model proposes that the applied stress is now shared between the elastic and viscous response, mathematically represented by a spring element in parallel with a dashpot element (see Equation 5, where T = HES / SS). Typically in modern modelling situations the Standard Linear Model is used, which consists of a spring element in series with the Voigt-Kelvin model and a further dashpot in series. This better represents the important features in the typical behaviour of a polymer. For a fuller treatment of viscoelasticity see Cowie [a.23].
Equation 1
Equation 2
A molecule in a solution is surrounded on all sides by other molecules that will normally interact with it. When the solution exists in an equilibrium state the pull from each of the surrounding molecules is matched by the pull from another molecule on the opposite side. However, consider that the molecule is on the surface of a boundary between two fluids. On this surface there will be an imbalance in the forces because the force between the molecules of the two fluids will be different from the force when the molecule is surrounded by its native fluid. This results in a force that pulls the liquid in such a way as to minimise the surface area to volume ratio. In the case of the air-liquid interface, air has little interaction with the liquid so the force is near its maximum. The physical meaning of surface tension is summarised in the approximate definition shown in Equation 8 (Approximate definition is taken from Wolfram Research’s website 'World of Physics' accessed on 16 March 2008 at http://scienceworld.wolfram.com/ physics/SurfaceTension.html) A fluid under the forces of surface tension will adopt a spherical shape, as this is the minimum surface area for a given volume. Figure 3 shows the forces experienced by fluid molecules. As there is a force acting on the outer surface it is possible to calculate the amount of work required to change the shape of the fluid. Equation 6 gives the energy (work) that must be either expended or will be generated when the surface changes its area (where G is the surface tension, E is the work energy and DA is the change in area). It is also possible to calculate the pressure due to the force from surface tension from Equation 7 (where P is the internal droplet pressure and r is the radius of the droplet). In a free droplet this pressure is the same from all sides but for the hemispherical droplet used in electrospinning this pressure would need to be matched by the fluid pressure that supplies the droplet. It can be said that for any fluid that has reached its equilibrium state there will need to be some other force acting in order for the fluid to adopt any shape other than that of the least surface area.
7
Electrospinning
Figure 3 Diagram of the forces experienced by molecules in a liquid.
Equation 6
Equation 7
whereas a weak electrolyte will commonly vary over all concentrations. The conductivity of a given cell is related to the molar conductivity by Equation 10, where K is conductivity with units of mS/cm, c is ion concentration with units of mol/l and hence the molar conductivity, , has units of Scm2/mol.
Equation 9 Equation 8 Equation 10
2.1.4 Conductivity The conductivity of a solution is determined by the potential for bulk motion of ions in the solution. When a potential difference is applied across a volume of solution, a current will flow that is proportional to the type of ions in solution and their respective concentrations. Conductivity due to a particular ion type in aqueous solutions can be seen in tables of molar conductivity (,). For very dilute solutions the contribution to the conductivity of a solution can be calculated from the Debye-Huckel-Onsager equation (Equation 9), where , is the molar conductivity, ,0 is the molar conductivity at infinite dilution, c is the ion concentration and A and B are typically taken to be 60.20 and 0.229, respectively, (see [a.24] for a full exposition). At higher concentrations a strong electrolyte typically has a constant molar conductivity
8
2.2 External Forces
2.2.1 Electrodynamic Force A single electron (having a negative charge) travelling in a vacuum in the presence of an electric field will experience a force given by Equation 11 (where F is the force exerted, q is the charge and E is the electric field). As it is a force, this is a vector equation and hence the electron will travel in the direction of the electric field. A proton (having a positive charge) would experience a similar force but in the opposite direction of the electron; all charge produces its own electric field. Like lines of magnetic flux (lines perpendicular to the equipotential
Electrospinning
surfaces), lines of electric flux cannot cross. A negative charge acts as a sink for field lines and a positive charge acts as a source. All field lines must either travel from a source to a sink or to the edge of infinity, which can be either a source or sink. For further discussion of electric forces refer to a physics textbook [a.25]. Equation 11
voltage and r is the droplet radius) to Equation 7 from Section 2.1.3 [a.26]. Both equations can be combined to give Equation 14, a relationship for the total pressure inside the droplet. It should be noted that this does not include the attraction due to the electric field present, but only the force due to surface charge repulsion, and becomes invalid once the droplet changes shape, because it is based on a spherical capacitor approximation.
Equation 12
2.2.2 Surface Charge If two charges of the same sign are next to each other there will be a force repelling them from one another. As like charges will both act as either a source or a sink for lines of electric flux (see Figure 4), this force is the result of the field warping to a higher energy state because the lines of electric flux cannot cross. The force of this repulsion is given by Coulomb’s law (Equation 12 where F is the force, q1 and q2 are charge, d is the distance between the charges and E0 is the permittivity of free space). Therefore, if a number of equally spaced charges of the same sign were deposited on the surface of a balloon then the surface would be stretched until the elastic force of the rubber was balanced with the repulsion force from the charge. The case of the droplet present at the moment the electric field is applied to initiate electrospinning is similar to the balloon example given previously. In this situation, surface tension is acting like the elastic force of the rubber, trying to contract the total volume to the minimum possible. As shown in Section 2.1.3 of this Chapter, the force from surface tension can be seen as a pressure pointing inwards whereas the force from the self-repulsion of the charge built up on the surface will be a pressure pointing outwards. This pressure is given by a similar relationship (Equation 13 where V is the applied
Equation 13
Equation 14
2.2.3 Fluid Pressure Pressure can be generated in a fluid in a number of ways. Hydrostatic pressure resulting from the weight of fluid above a chosen point is given by Equation 15. This is also known as the head pressure. Pressure can also be supplied by pressurising the supply tank for the fluid typically with an inert gas. In this case as a liquid is typically incompressible, the pressure from the gas will be directly translated to the other boundaries of the fluid. Another common procedure in electrospinning is the use of a syringe pump to provide a controlled volume flow rate. Here, as long as the fluid pressure does not exceed the power of the syringe pump, the pressure will be related to the other forces and geometry in the system. Equation 15
Figure 4 Electric flux lines from a source and a sink.
9
Electrospinning
3 ELECTROSPINNING PROCESSES AND APPARATUS 3.1 Simple Process Description 3.1.1 Axis Conventions In order to discuss the electrospinning process in a concise and transparent way it is important to note the common axis conventions used in models. Typically a cylindrical co-ordinate system is used [a.27]. This system describes a point in 3-D space given a distance along a Z axis followed by an angle to rotate around the Z axis then a distance to travel perpendicular to the direction of the Z axis (Figure 5). The direction of the Z axis is chosen to be such that the maximum level of symmetry is obtained around that axis. If the axis is chosen such that it passes through the centre of the first electrode, then through the centre of the polymer droplet and lastly through the centre of the second electrode, it often obtains the maximum symmetry possible. This axis can then be referred to as the primary axis.
Figure 5 Cylindrical axis convention.
3.1.2 Basic Physics of Electrospinning Electrospinning can be viewed as a special case of electrospraying. The latter is a method of atomising fluids that finds applications in mass spectrometry, industrial applications (e.g., coating of automotive parts with complex shapes) and consumer products (e.g., deposition of ink by inkjet printers).
As with electrospraying, the feedstock for electrospinning is connected to a high voltage power supply to raise the electrostatic potential of the fluid. Polymer solutions or melts with a minimum degree of molecular interaction can be used as the feedstock. Increasing the electrostatic potential increases the surface charge of the liquid. Normally the shape of a volume of fluid is dictated by its surface tension. However, when the fluid is charged the surface charge acts in the opposite manner to surface tension, resulting in the fluid changing shape, forming the structure known as the Taylor cone [a.4]. If the surface of a conductor forms a sharp point, the electric stresses will concentrate on that point. In a Taylor cone, there is a sharp point at the tip of the cone, so this concentration of electric stresses leads to the ejection of a fluid jet due to the increased electrical attraction at the tip. This fluid jet carries a charge, so it will be drawn in the direction of the local electrostatic field. After a certain amount of flight time this jet will become vulnerable to a number of instabilities. Careful control of these instabilities ensures successful fibre formation. For example, the axisymmetric PlateauRayleigh* instability, which causes atomisation in the electrospraying process, must be avoided to ensure fibre formation. Included in the electrospinning process is the off-axis bending instability that is largely responsible for the narrow fibre diameter obtained during electrospinning [a.28]. The off-axis bending instability occurs due to small perturbations in the straight line trajectory of the fibre, which generate a force perpendicular to the primary axis due to the self-repulsion of the charged jet when perfect symmetry is lost (see Figure 6). This force is very small and is initially countered by the viscoelastic nature of the polymer solution. The viscous component will resist the motion generated by this force and the elastic component will work to restore the perturbed fibre to its original position. However, at some point the perturbation forces become larger than the resistance, at which point the bending instability begins to grow, causing additional stretching of the jet. This will continue throughout the rest of the jet’s flight assuming the localised electrostatic repulsion stays larger than the mechanical resistance of the jet/fibre to stretching [a.22]. The high surface area of these narrow fluid jets allows rapid solvent loss, leading to the conversion of the fluid jet into a solid fibre within the short flight time. It has
* Plateau-Rayleigh instability is the result of surface tension reinforcing small perturbations in a fluid column’s surface eventually leading to the breaking up of the fluid column and the formation of droplets. For a full mathematical treatment see Lecture 7.5 of the MIT course 1.63J/2.21J Advanced Fluid Dynamics of the Environment accessed on the 12 March 2008 from http://web.mit.edu/1.63/www/lecnote.html
10
Electrospinning
Figure 6 Physical diagram of perturbations causing the bending instability (modified from [a.29]). Here A, B and C represent three discrete equally charged sections of the jet where B has been perturbed from the symmetrical axis.
been observed that polymer molecules within these fibres can have a high degree of orientation (409). This has been explained both by the alignment of polymer molecules due to the electrostatic field and by the high draw ratio of the fibre while in flight.
3.2 Process Models In the past decade, significant process model developments have been made since the work of Zeleny [a.3] and Taylor [a.4]. Many of the proposed models have had some validation against experimental data and have been used to help explain experimental observations. This suggests that a good understanding in the models, though unable to fully predict results, can significantly reduce research and development time for new fibre applications. Thompson and co-workers claim in reference to Yarin and co-workers that the proposed model is ‘the only existing model of electrospinning, accounting for the large nonlinear perturbations, viscoelasticity, evaporation and solidification’ [a.22, a.30]. This would make it the most complete model proposed at this time. The following sections expand the discussion outlined in Section 3.1.2.
the voltage at which discharge of mass begins (either of a smooth fluid jet or an aerosol stream). Taylor [a.4-a.6] undertook a theoretical examination of jets being initiated from a polymeric fluid on the end of metal capillaries. Taylor described cone formation with a semivertical angle of 49.3° (see Figure 7), apparently true for any conducting fluid. The validity of this cone geometry has been questioned by Yarin and co-workers [a.32] and Reznik and co-workers [a.20], who find it to be a 33°. Taylor found a relationship between his initial conditions and the formation of his cone (Equation 16). Here H is the distance between electrodes, L is the length of the capillary tube (syringe needle), R is the radius of the tube and G is the fluid’s surface tension (all expressed in CGS*
3.2.1 Jet Initiation Jet initiation is one of the direct consequences of exposing a fluid drop in contact with a conductor to a strong electric field. As a result, much of the work on jet initiation has been done in tandem with theoretical treatments of electrospraying. Many authors [a.3, a.4, a.31] have focused on the concept of a critical voltage:
Figure 7 Taylor cone formed by a 98% glycerine and 2% of 10% NaCl solution with an exposure time of 1 ms [a.6].
* Centimetre-Gram-Second as opposed to MKS or Meter-Kilogram-Second
11
Electrospinning
Figure 8 Critical electric Bond number versus static contact angle [a.20].
units as per the original paper). Although Taylor’s model of electrospinning might only hold true for specific cases [a.20], his simple equation negates the need for extensive modelling and it can still be used to predict the critical voltage required to begin jet initiation.
Equation 16
Equation 17 Later work by Reznik and co-workers on the evolution of droplets on an infinite plane over time showed that the static contact angle formed by the fluid droplets was critical in predicting jet initiation. Reznik and co-workers introduce the concept of the electric Bond number (see Equation 17 where Ec is the applied field, G is the surface tension and a0 is the equivalent-volume drop radius or characteristic length) allowing the description of the relative importance of electric and capillary stresses [a.20]. For a range of contact angles, the critical values for the electric Bond number were calculated (Figure 8) and hence, the critical voltage needed to form the Taylor cone can be calculated for a given polymer solution. Evolution of the droplet shape can be either subcritical or supercritical. If the electric Bond number is low then a subcritical evolution occurs. Here the droplet adopts a partial cone shape, but the hydrodynamic forces still dominate and the droplet will not evolve into a jet. If the electric Bond number is above the critical level then a supercritical evolution towards the typical Taylor cone will occur because the mechanical stresses from the electric field dominate the droplet evolution. Concentration of electric stress at the tip of the cone [a.32] will cause the continued formation of a typical electrospinning jet.
12
3.2.2 Jet Thinning Once the jet has left the Taylor cone it will begin to thin due to the forces acting on it and the requirements of conservation of mass, until it hits the collector electrode. The thinning of the jet has two different stages. The initial stage is a period of thinning as a straight jet and the later stage is a period of thinning due to the bending instability (see Section 3.2.4). The initial thinning behaviour of the jet can be described simply with the Bernoulli principle [a.33]. In electrospinning, losses due to viscous flow must be incorporated into the Bernoulli formula and electrodynamic forces will replace gravity as the driving force. This treatment, such as that by Spivak and coworkers, results in one-dimensional axisymmetric ~ differential equation (Equation 18, where R and ~ z are dimensionless lengths, NW is the Weber number, NE is the Euler number and NR is the Reynolds number) that usually can be solved directly [a.34]. As the jet continues to thin, its surface area increases and hence the potential for solvent loss increases. At some point all the solvent is lost and the jet is no longer fluid, becoming a material with a modulus of elasticity rather than a viscosity, and at this point the mode of thinning
Electrospinning
Equation 18
Figure 9 Plateau-Rayleigh instability where A is the stable region, B is where perturbations begin to become visible and C is when the perturbations have become larger than the radius causing droplets to form.
changes. Solidification results in a much higher portion of the stretching force being taken up by an elastic mode of stretching, hence a significant reduction in the rate of thinning [a.19].
3.2.3 Fluid Instabilities Fluid instabilities can be detrimental to the electrospinning process because they are the cause of jet break up (i.e., electrospraying) preventing fibre formation. However, the bending instability, according to Reneker and co-workers [a.28] is vital to the electrospinning process, so the control of fluid jet instability is what differentiates electrospinning from electrospraying. This control can be accomplished via solution properties, e.g., increasing the polymer component, leading to an increase in inter-molecular interaction. Work by Hohman and co-workers [a.21] has shown that there are typically three types of instability that may occur in the charged electrospun jet. The first is the classical axisymmetric Plateau-Rayleigh instability
[a.35], the second is a similar axisymmetric instability caused by having a conductive jet, and the third is the bending or ‘whipping’ instability (section 3.2.4). The Plateau-Rayleigh instability is an axisymmetric phenomenon dependent on surface tension, and is commonly observed when water from a tap breaks up from a stream into droplets (see Figure 9). It occurs because surface tension draws the fluid jet into a shape with a minimum surface area for a given volume. The surface area of a column (as of a falling stream of water) is significantly reduced if the column is broken up into a series of spheres. When an oscillating perturbation term is introduced into the governing equations, the solution matches the observation that some of the wavelengths will grow rapidly and eventually result in the jet breaking up into droplets. Work by Shin and coworkers and Hohman and co-workers showed that this instability only occurs at low external electrostatic fields where the electric field stresses are small compared to the capillary stresses [a.21] (677).
13
Electrospinning
Figure 10 Axisymmetric instability for a perfectly conducting fluid column where e is the electrostatic contribution to the perturbation of the flow and u is the velocity contribution to the perturbation of the flow due to an introduced radial perturbation [a.21].
Figure 11 Formation of a droplet being ejected from the tip of a Taylor cone if the contact angle is above ~0.8 P radians.
The second axisymmetric instability replaces the Plateau-Rayleigh instability at higher electric field strengths. This instability only occurs because the jet has a finite conductivity and carries an initial surface charge. In this case electrical stresses as a result of perturbation waves on the surface of the jet cause shifting of the surface charge in order to maintain a constant electric field flux in the jet column. The result of this is that the perturbation is reinforced and the jet will eventually break up into droplets. Hohman and co-workers found through mathematical modelling that this instability would preferentially develop rather than the desired bending instability, unless ‘reasonable estimates for the surface charge density’ were included in the model (for example: S = 9.8 x 10-8 C/m2) [a.21].
14
There are other instabilities, such as the dripping mode proposed by Reznik and co-workers. This only occurs if the surface-liquid interfacial energy for the solution and the tip is high enough to generate a contact angle of above ~0.8 P radians; then excessive mass is ejected from the tip of the Taylor cone to sustain a jet (Figure 11). Reznik and co-workers propose this as an explanation for the large droplets sometimes ejected from the Taylor cone [a.20].
3.2.4 Bending Instability Initially it was proposed by Doshi and Reneker that the primary mechanism for production of nanofibres was
Electrospinning
Figure 12 Typical representation of the bending instability.
the surface charge reaching a critical value, causing the single jet to split into multiple jets, known as ‘splaying’ [a.18]. However, subsequent work with high speed photography using an exposure time of 18 ns [a.36] has shown that this ‘splaying’ observation is simply an optical illusion caused by the high speed of the fibre. The true instability is a fast-moving ‘whipping’ jet that forms multiple expanding loops which eventually deposit on the collector electrode. The bending instability is idealised as a series of neatly expanding loops (see Figure 12). This bending instability allows the jet to undergo far more stretching during its flight time than would be allowed by a simple linear jet. By taking a localised approximation of the electrostatic force between two points on a curved three-dimensional fibre, Yarin and co-workers showed that it is possible to derive an equation for the force driving the bending instability (see Equation 19 where SS is the surface charge, L is the characteristic length, as is the jet radius, k is the jet curvature and X is the co-ordinate system along the central axis of the bent jet) [a.22]. The equation is sufficiently similar to the form of the equation for the force that drives the aerodynamic bending instability also described by Yarin [a.37], that substitution into this previous work could be done. Yarin and co-workers also showed that the path of individual jet elements is such that the loops formed by the bending instability grow in radius by thinning and stretching [a.22]. Experimental observations are matched by incorporation of jet solidification, which limits the rapid expansion of the loops. As such, the bending instability is currently a primary concern for research into the production of desired electrospun fibre properties.
Equation 19
3.2.5 Polymer Chain Alignment By calculating draw ratios, Wang and co-workers demonstrated that the fibre undergoes large amounts of stress parallel to the fibre axis during electrospinning (409). Additionally, a higher degree of crystallinity was observed as a result of the high draw ratios encountered. It was proposed that the high draw ratios in electrospinning act like the drawing of a fibre in traditional fibre processing, where the fibre is stretched to align the polymer chains, increasing the crystallinity, and hence, tensile strength of the processed fibres. Zhao and co-workers [a.38] demonstrated that if given sufficient flight time, electrospun fibre produced under a higher potential difference, and hence a stronger electric field, would result in improved crystallinity. It is possible that the improved crystallinity is due to additional stretching of the jet under the action of the stronger electric field. However, it could be possible that the electric field encourages the alignment of the polymer molecules (c.f. electrophoresis) and hence a stronger field would result in more molecules being aligned.
3.3 Process Parameters In electrospinning, numerous parameters have been identified as affecting the final properties of the electrospun fibre (548); these factors will be explored further here. Mit-Uppatham and co-workers break
15
Electrospinning
Table 2 Electrospinning process parameters [based on (548)]. Solution Parameters
Process Parameters
Environmental Conditions
Concentration
Electrostatic Potential
Temperature
Viscosity
Electric Field Strength
Humidity
Surface Tension
Electrostatic Field Shape
Local Atmosphere Flow
Conductivity
Working Distance
Atmospheric Composition
Dielectric Constant
Feed Rate
Pressure
Solvent Volatility
Orifice Diameter
these parameters down into three broad categories: (i) properties of the solution used as the feedstock (solution parameters), (ii) parameters associated with the design, geometry and operation of the electrospinning apparatus (processing parameters), and (iii) atmospheric and other local processing conditions (environmental parameters) (Table 2) (548).
3.3.1 Solution Parameters The solution properties such as volatility, dielectric constant, solution conductivity and surface tension may be affected by additives (e.g., a surfactant will reduce surface tension). Jarusuwannapoom and coworkers provide an excellent study of the effects of using different solvents with a wide range of properties (543). When a solvent with a very low volatility is used, wet fibres are collected (i.e., appearance of a film with pores rather than a fibre mat). However, if the solvent is too volatile the Taylor cone will solidify, halting the production of fibre. The same study also found that the dipole moment of the solvent and the solution conductivity must both be of a sufficient level to enable electrospinning to occur. A recent theoretical study [a.30] has shown that surface tension has almost no effect on the final properties of the electrospun fibre. This finding is consistent with the work of Hohman and co-workers and Yarin and coworkers who both find that once the bending instability sets in, the electric stresses are far larger than the capillary stresses [a.21, a.22]. However, Fong and coworkers show that modification of surface tension (by surfactant or solvent mixes) can assist in the formation of smooth fibres (682). Introduction of additives to the solution, often ionic salts, enable the modification of either the solution conductivity (542) or surface tension (615). For solutions with very low conductivity, adding ionic salts to increase the solution conductivity has been shown to enable jet formation to occur, but further addition beyond this is currently being debated.
16
In addition to the work done by Jarusuwannapoom and co-workers, work by Eda and co-workers (283) and Koski and co-workers [a.39] shows the importance of polymer concentration in the solution. This is due to the requirement for a sufficient level of intermolecular interaction that will help to damp the fluid instabilities and prevent jet break-up. When the concentration is too low, a deposition pattern occurs similar to that expected for electrospraying. As the concentration is raised, a bead-on-a-string morphology (680) is observed, with the beads slowly becoming more spindle-like and merging into the fibre as concentration increases. At a suitable concentration a smooth fibre is obtained. Directly linked to the polymer concentration is the solution viscosity noted by Megelski and co-workers and Deitzel and co-workers as important in both the jet initiation and the final fibre properties (679) (656). As the solution viscosity increases it has been observed that the fibre diameter increases (659).
3.3.2 Processing Variables The operation of a typical electrospinning apparatus will involve the modification of the applied electrostatic potential, the working distance and the feed rate. Variation of the applied electrostatic potential and the working distance will also cause variation of the electric field strength. Typically, researchers will look at either the electrostatic potential (571) or the electric field strength (681). It has been found that increasing the electrostatic potential will result in thinner fibres (656). The working distance, together with the electrostatic potential will determine the strength of the electric field. However, to complicate things, the working distance also changes the total flight time available to the fibre. As such, in some cases increasing the working distance results in thinner fibres [a.28] due to more time for the bending instability to develop and hence more time for the jet to be stretched.
Electrospinning
In other cases, increasing the working distance results in thicker fibres due to a reduction of the electric field (664). However, at too long or short a distance, jet initiation becomes difficult due to the electric field being too strong or weak. Typically the electric field strength required to initiate electrospinning is a value between 0.5 and 1.5 kV/cm. If the localised electric field value exceeds the dialectic strength for the atmosphere then a corona will be generated, the effects of which are currently unknown. There are comparatively few experiments done examining the feed rate (664) [a.40], probably due to feed rate being used as a control parameter for stabilisation of the Taylor cone. However, in the study by Yuan and co-workers a low feed rate was shown to form very thin and dry fibres (559). Work by Rutledge and co-workers demonstrated that with increased feed rates the fibres became much thicker and fibres with the characteristic beads-on-a-string morphology were formed [a.40]. The electrode geometry and addition of secondary electrodes can be used to control deposition patterns or the extent of the bending instability. Work such as Teo and Ramakrishna shows that the modification of the electric field allows control over the fibre flight and hence the modification of the final fibre alignment [a.41]. In addition, the design consideration of the orifice diameter for the spinning head has been examined by some authors [a.30] (605). It was found that larger orifices resulted in thicker fibres (605). When the orifice size was very large it was difficult to obtain a stable Taylor cone, whereas very small orifices become impractical as the Taylor cone will dry out or the polymer will be too viscous to flow through [a.38].
3.3.3 Environmental Conditions Environmental parameters can be divided into those that are due to the local spinning conditions or the properties of the atmosphere in which the spinning takes place. The study by Kim and co-workers found that increasing the local temperature resulted in the solvent evaporating faster and provided a simple solution to solvents with a low rate of evaporation (509). For excessively volatile solvents the Taylor cone will dry out. It is possible to introduce a local flow of gas saturated with the solvent around the cone to prevent evaporation at the cone [a.42]. Introduction of a dry gas has also been used to control the evaporation rate of the solvent in the jet (681). Controlling the atmosphere into which the fibre is spun is the subject of a patent by Andrady and co-workers [a.43].
Electrospinning with an atmosphere composed of a high breakdown strength gas would enable much higher field strengths to be reached. Baumgarten found that using sulfur(VI)fluoride (SF6), a gas with a high dielectric strength and density, resulted in an increase in the fibre diameter [a.44]. It was asserted by Ramakrishna and co-workers that ‘generally, reduction in the pressure surrounding the electrospinning jet does not improve the electrospinning process’ [a.29]. However, due to the lower vapour pressure in a vacuum, solvent loss would be faster and could solve the problem of low evaporation rate solvents. Humidity has been shown by Casper and co-workers and Megelski and co-workers to allow control over the formation of micropores on the surface of the individual fibre (656) (597).
3.4 Core Apparatus In its simplest form, an electrospinning apparatus need not be anything more than a high voltage power supply, a drop of polymer solution and an earthed electrode (Figure 13). The often quoted 1934 patent by Formhals shows an apparatus not far removed from the basic elements required (Figure 14). A typical electrospinning apparatus used in research, such as those produced by Electrospinz, Blenheim, New Zealand (Figure 15), consists of a constant pressure polymer solution supply, a high voltage electrode, a spinning head (Spinning head describes either a metal capillary or some other nozzle or orifice through which the polymer solution or melt is delivered) and a collector electrode. The polymer is supplied to the capillary tip, forming a hemispherical droplet that is the precursor of the Taylor cone. The method of supply can be either constant volume flow rate or constant pressure. Constant pressure is typically provided by either a gravity fed constant head system or an air pressure system. The more common constant volume flow rate is typically supplied by a syringe pump (622). The high voltage electrode is used to conduct the charge to the polymer solution. It is constructed typically from a hypodermic syringe needle (681) and is also the spinning head. Another common method of charging the solution is by use of a bare wire inserted into the polymer solution [a.18]. Collector electrodes come in many shapes and sizes but are commonly some form of flat metallic sheet (557) and Norton [a.9]. This electrode is typically connected to ground, hence carrying the opposite charge to the high voltage electrode. They are often mounted in such a way to allow their position relative to the spinning head to be changed.
17
Electrospinning
Figure 13 Simple elements required for electrospinning.
Figure 14 Diagram of the apparatus proposed by Formhals [a.11]
Figure 15 Electrospinz ES1 apparatus.
18
Electrospinning
3.5 Modifications and Additions to Core Apparatus
perform modifications to the collector, which will be discussed further in Section 3.5.3. Beyond modifications to the existing electric field, the introduction of other external electric fields has also been proposed.
3.5.1 Polymer Supply Modifications
One approach to electric field modification at the capillary is to surround the capillary with a polyvinylchloride (PVC) tube. Yang and co-workers propose that this will create a more uniform and concentrated electric field leading to better control of the fibre deposition [a.49]. Work by Kim demonstrated the use of an auxiliary electrode placed around the capillary that was charged from the same power supply as the polymer solution in the capillary (422). It was found that this auxiliary electrode stabilised the initial straight portion of the jet.
Typical motivation for the modification of the polymer supply is to increase the quantity of electrospun fibre produced. One of the earliest modifications to the polymer supply mechanism is to have a supply to multiple spinning heads [a.45]. Following a similar line of thinking an unusual method was developed by Yarin and Zussman involving floating a layer of polymer solution on top of a layer of mineral oil containing magnetic particles whereby the application of a magnetic field resulted in the formation of multiple spikes in the fluid that jets can be evolved from (593). A recently commercialised method is to use a roller partially immersed in a bath of polymer solution. This process extends the concept of a rotating cog spinning device first proposed by Formhals [a.10] and the use of an air-blast proposed by Norton [a.9]. The roller acts as the polymer-charging electrode and the polymer supply is maintained on its upper surface as a thin curved film. Volume flow rate is increased by blowing an air stream across the roller in a fashion reminiscent of glass fibre spinning [a.46]. This patented process can produce numerous jets from the top of the roller, allowing continuous sheets of an electrospun mat to be produced [a.47]. The addition of a (inert) gas flow around the capillary delivering the polymer is also used to influence the motion of the jet (183). A gas atmosphere saturated with solvent will prevent a volatile polymer-solvent mixture from drying out at the end of the capillary before electrospinning can occur: the recovery of solvent by enclosing the spinning environment was proposed by Gladding, but the benefit of this is more in isolating the worker from the solvent system because the quantities recovered are likely to be small [a.17]. Hollow or composite nanofibres can be produced by using a nested capillary such as demonstrated by Li and Xia [a.48]. Here the centre capillary is supplied with mineral oil and the outer capillary is supplied with poly(vinyl pyrrolidone). After spinning the mineral oil is removed via pyrolysis, leaving a hollow fibre.
Use of an auxiliary electrode is normally the only way to introduce a new external electric field. The work by Dabirian and co-workers used a negatively charged bar to direct the electrospun jet towards a rotating collector [a.50]. In the work by Gu and co-workers, an auxiliary electrode was used to create twisted nano-fibre yarns [a.51]. The introduction of two parallel bars in the path of the electrospun fibre allowed Chuangchote and Supaphol to collect a mat of both aligned fibres from the parallel bars and a random orientated mat deposited on the collector behind the bars [a.52]. Liu and Dzenis model this parallel bar set up, and demonstrate that the level of alignment is higher that that achieved with a rotating drum collector, but the build-up of charge on the deposited material leads to a decrease in deposition rate and in the quality of alignment with time [a.53].
3.5.3 Collector Modifications A typical motivation for the modification of the collector from a flat metal sheet is to provoke some degree of alignment in the deposited fibres. This is demonstrated by the widely reported use of a rotating mandrel and parallel bars to form aligned mats. Another collector modification is the use of a cylinderlike collector, proposed by Jirsak and co-workers as a consequence of the polymer supply geometry [a.47]. One interesting modification of the collector by Simonet and co-workers involved the refrigeration of the collector, allowing the formation of ice crystals as the electrospun fibre is deposited (165). These ice crystals form a removable void template to create a high loft porous 3D polymer mesh.
3.5.2 Electrostatic Field Modifications Three approaches are taken to modification of the electrostatic field. One is to modify the field at the capillary origin of the polymer fibre. Another is to
A good example of the use of a rotating mandrel is shown in the work by Sundaray and co-workers who used a high speed rotating mandrel to produce aligned fibres [a.54]. Sundaray and co-workers also took this a
19
Electrospinning
step further by use of an insulating mandrel with a sharp moving pin as the counter electrode to reduce the size of the deposition area concentrating the aligned fibres [a.54]. Teo and Ramakrishna used a similar concept by taking a rotating knife edged disk as their collector [a.41]. They were able to collect a mat of aligned hollow fibres. Formhals (see Figure 14) described a toothed belt where each tooth acted as a collector electrode [a.10]. It was proposed that this arrangement would result in the production of a continuous tow of aligned fibre that could later be processed by standard textile means. A good example of the use of parallel bars to allow the alignment of electrospun fibre is shown in the work by Li and co-workers (598). Here the parallel bars that are used are gold electrodes mounted on a quartz substrate. Under fast switching of each electrode to ground, the fibres will jump between the two bars, creating an aligned mat. This was then extended to multiple axes on the two-dimensional substrate to create layers of aligned fibres in different directions. Other examples of such a technique are shown in works by Li and co-workers (598) and Ajayan and co-workers [a.55].
4 APPLICATIONS Interest in electrospinning for real world applications is due to three aspects of the process. First, the size of the fibre is in the nanoscale or has a nanoscale surface texture, leading to different modes of interaction with other materials compared with macroscale materials [a.56]. Second, due to the high draw ratio it is expected that the fibres produced will have a highly orientated molecular structure with a low number of defects, and will hence approach theoretical maximum strength. Third, the fibres produced have an inherently high surface area to volume ratio. Combinations of these three aspects give rise to applications in filtration, cellular matrices, catalyst substrates, ultra-strong composites, bioreactors, functional textiles, drug encapsulation, wound dressings and stent manufacture.
4.1 Nanoscale Materials It has been demonstrated widely in the field of nanotechnology that when a material is formed with a nanoscale structure such as nanoparticles or nanofibres, then the interaction behaviour of such materials can drastically change [a.56]. In biological systems the micro- and nano- structure of materials becomes a very
20
significant factor as cell behaviour is dependent on the local material structure. This has recently become more important as the field of tissue engineering has developed creating demand for nanostructured materials for tissue scaffolding. Similarly, due to interactions on the molecular scale becoming dominant, nanostructured composite materials are pushing the boundaries of materials science. It has also been demonstrated that the use of nanofibres for filtration is vastly superior to traditional filtration materials in performance and operation. It has been shown in some cell culture studies that a nanostructured material can affect cell seeding, attachment, and propagation. Moroni and co-workers used unaligned fibres of polyethylene oxide terephthalate - polybutylene terephthalate co-polymer and a cell culture of human mesenchymal stem cells [a.56]. They demonstrate that a 10 μm fibre diameter produces the best results for cell seeding and attachments. It was also demonstrated that cell propagation was highest when the fibre surface has a nanoporous structure. With a nanoporous structure the cells were observed to penetrate more deeply into the tissue scaffold within 14 days than smooth fibres; the use of smooth fibres tended to result in cell aggregation. Bhattarai and coworkers used unaligned fibres of a chitosan/polyethylene oxide blend and a cell culture of human osteoblasts and chondrocytes to show that cell attachment and propagation was significantly better with electrospun fibre than with a cast film of the same material [a.57]. It was also found that cells on the electrospun fibre retained their expected morphology and would propagate along the fibre direction. Li and co-workers used unaligned fibres of a polyaniline/gelatine blend and a cell culture of cardiac rat myoblast cells [a.58]. They found that although after two days cell propagation was lower than the control, it was significantly higher after six days. This was attributed to fibrous substrates being rougher and hence giving more room for cell propagation. It was also found that when large fibres were used in the scaffold, cells would propagate along the fibres whereas when smaller fibres were used the cells produced morphology similar to smooth muscle. This was confirmed by scanning electron microscopy, showing that cells preferentially grew on smaller fibre substrates. The application of nanofibres in composites can be summed up in the statement by Moroni and co-workers [a.56]; “… that using building blocks with dimensions in the nano-size range makes it possible to design and create new materials with unprecedented flexibility and improvements in their physical properties.” The reason for this can again be summed up: “Special properties of nanocomposite materials often arise from interaction of its phases at the interfaces.” This becomes so important
Electrospinning
in nanomaterials because the high surface area available for the interfaces means a higher fraction of the material has the properties of the interfacial region rather than the properties of the bulk material. As the properties of the interfacial region are usually significantly different from those of the bulk material, the inclusion of nanomaterials in a composite allows greater control of the final material properties. In a review of electrospun fibre composites, Chronakis and co-workers cite two examples of electrospun fibre being used to improve mechanical performance. The inclusion of electrospun aromatic heterocyclic polybenzimidazole fibres into a rubber matrix resulted in a 10-fold increase in the Young’s modulus and a doubling of the tear strength. The inclusion of electrospun Nylon-6 fibres into a dental restorative compound with a fibre loading of 5 wt% resulted in an increase in the flexural strength, the elastic modulus and the work of fracture, the most significant change being the work of fracture, increasing by 42%. In further discussion of the potential for electrospun fibre, Chronakis and co-workers point out that due to electrospun fibres being continuous (hence having a high aspect ratio l/d) these fibres have the potential for homogonous dispersion in a matrix [a.59]. Due to this homogonous dispersion, other property enhancements that are not mechanical can be considered, such as electrical and thermal properties. This would allow the combination of the flexibility and non-corrosiveness of polymers to be applied to previously impractical areas, making electrospun fibres a valuable new tool in designing new materials.
4.2 High Tensile Strength Fibres It was shown by Feng and co-workers that during electrospinning the fibre typically undergoes a large amount of stretching [a.60]. It is expected that due to the action of the force stretching the fibres and because the fibre diameter is close to the molecular scale, the polymer molecules will be highly aligned with little room for defects in the structure – as a general proposition, the thinner the fibre, the nearer it will approach its theoretical maximum strength (628). Wang and co-workers found that electrospun silk fibroin fibres undergo a draw ratio (L = v1/v2) of above 1 x 105 (409). This draw ratio is an order of magnitude above that typically achieved by a silkworm and was the proposed explanation for a high degree of crystallinity observed by wide angle x-ray diffraction. Although some of the fibres' crystalline structure resembled the natural structure of spider or silkworm silk, the high draw ratio alone was not sufficient to reproduce the natural structure of these silks.
In the review paper by Chronakis and co-workers there is an example cited of mechanical testing of a single strand of polycaprolactone using a nanotensile tester [a.59]. This showed that for thicker fibres the mechanical properties were the expected low strength, low modulus and high ductility of bulk polycaprolactone. However, thinner fibres showed a higher strength but lower ductility, consistent with a high draw ratio causing a higher degree of crystallinity in the fibre. Work by Ko and co-workers (628) used an atomic force microscope tip to measure the elastic modulus of electrospun fibre [a.62]. They found that their polyacrylonitrile fibres behaved as if giving an elastic modulus of 66 GPa. However, with the incorporation of single walled carbon nanotubes into the fibre there was a non-linear response to the applied force and the increase in elastic modulus (110 GPa for 3 wt% nanotubes) was significantly higher than that predicted by the theory of mixing. It was proposed that this was due either to the interaction between the carbon nanotubes and the polymer increasing stiffness, or to underestimation of the nanotube modulus or volume fraction. Transmission electron microscope images demonstrated that the carbon nanotubes were well aligned along the fibre axis.
4.3 Surface Area to Volume Ratio The formula for the volume of a given cylinder is V = Pr2l whereas the surface area of a given cylinder assuming the end caps are excluded is A = 2Prl. For electrospun fibres we can assume that an average fibre diameter can be measured for a given sample and that this fibre can be effectively represented by a cylinder. Using these assumptions then the surface area to volume ratio can be simplified to 2/r. As this simple relationship is proportional to the inverse of the average fibre radius then to maximse the ratio the smallest fibre diameter needs to be used. The smallest electrospun fibres (3 nm claimed by Viswanathamurthi and co-workers [a.63]) are approaching the scale of the molecules that make up the fibres. This effectively means that electrospinning is a method suitable for producing fibres close to the limit of surface area to volume ratio. Any process that is dependent on surface area, such as active filtration, catalysts, fibre-matrix interactions, bioreactor cores and chemical sensors will benefit from the incorporation of nanofibres into the process. It has been shown by Viswanathamurthi and co-workers [a.63] and Li and Xia [a.87] that electrospinning can be used to produce fibres where the polymer acts as a carrier and a metallic precursor material [a.48, a.64].
21
Electrospinning
4.4 Medical Applications Products aimed at the medical market are often high added-value products with small production volumes and hence the medical industry has been a big focus for the development of electrospinning applications. This circumvents, for now, the difficulties with current technology in producing large volumes of fibre. These applications fall into two main groups, patient consumables such as wound dressings and drug delivery, and procedure consumables such as tissue scaffolds. A simple example of electrospun fibre being used for wound dressings is shown in the patent by Siniaguine, which describes a multi-layered wound dressing [a.64]. This wound dressing incorporates an outer microfibre layer that is hydrophobic, to repel external moisture, a middle layer that is partially water-soluble to retain fluids and keep the wound moist, and an inner insoluble hydrophobic fibre layer that has large pores to encourage fluid to be removed from the wound. A patent by Larsen and co-workers demonstrates a modification to standard wound dressings where the increased surface area to volume ratio is used to expose blood to a coagulating enzyme, creating a haemostatic dressing [a.65]. Thanks to the ability of electrospun fibre to act as a carrier for non-polymeric molecules, another important application has been to use the fibre as a drug carrier. Both biodegradable and permanent fibres have been proposed. The patent by Kaplan and Lorenz describes fibres formed by silk-fibroin that have been postprocessed to control the crystallinity and hence control the rate of drug release [a.66]. This patent proposes an article with either a single layer or a multi-layer to allow different therapeutic agents or concentrations to be released over time. A similar approach was proposed by Verreck and co-workers in his paper, where model drugs such as the antifungal itraconazole were incorporated into insoluble fibres and a controlled release was observed for the water-insoluble drugs observed [a.67]. As an alternative to the diffusion-controlled drugrelease mechanism, Zeng and co-workers propose a biodegradable polymer to encapsulate the drug [a.68]. In that paper, fibres are formed from polylactic acid (PLA) with a model drug encapsulated in the fibre. Once exposed to biological conditions the fibres break down and release a continuous amount of the encapsulated drug with out any burst release. A large amount of electrospinning research has been focused on the production of tissue scaffolds. Electrospinning is beneficial here because the fibres produced are of a similar scale to the extracellular matrix of natural tissue. Because of the potential for
22
biopolymers to be electrospun, it may be possible to produce complete tissue. The patent by Gingras describes a general method for making tissue scaffolds using layers of fibre electrospun from ‘biocompatible’ polymers [a.69]. In its simplest embodiment it describes two films where the first film has numerous opening for cell seeding and the second film, below the first, has a number of larger cell openings connected to the openings in the first films for cell propagation. The patent by Guilak and Moutos extends the basic concept, describing a tissue scaffold that has multiple layers woven into a 3D structure to aid in the restoration of tissue that is implanted in the body [a.70]. More complex electrospun tissue engineering scaffolds have also been proposed such as vascular implants or scaffolds, including those described in the patents by Shastri and Sy [a.72] and Neuenschwander [a.71]. Neuenschwander’s patent also describes methods for constructing an artificial heart valve using electrospun fibre. The applications already covered by existing patents are wide-ranging, with patents such as that by Lu and co-workers that describes a tissue scaffold for the fixation of musculoskeletal soft tissue to bone [a.73], and the patent by Bertram and co-workers which describes methods of using electrospun fibre to repair, reconstruct, replace or augment organs in a patient, primarily focused on the bladder [a.74]. Rather than the production of natural organs, the patent by Shalev describes an interesting technique of creating so called ‘artificial organs’ [a.75]. This is embodied as a bioreactor that is separated from the natural circulatory system by a membrane allowing the continuous production of compounds that are subsequently passed into the circulatory system.
4.5 Materials Applications The original intended use of the electrospinning process was for the production of textile fibres. This is embodied in the patents by Formhals where a high voltage electric field is used to draw fibres from a cellulose acetate solution [a.10]. There is also work being done to use electrospun fibre as a carrier for chemically active species to create functional textiles (328). On a similar note, the paper by Ko and co-workers (628) describes a method of producing twisted yarns of nanofibres using a flow of compressed air that can then be used in more traditional textile processing apparatus [a.62]. One major potential application for electrospun fibre is in the manufacture of nanocomposites. As discussed in Section 4.1 the incorporation of nanoscale material into a composite matrix produces different results from the incorporation of macro scale material.
Electrospinning
The significant advantage of using electrospun fibre is that the nanoscale material is continuous in nature, meaning it has a very high aspect ratio. Continuous fibres also offer the potential for increased safety due to lower potential toxicity of the nanoscale element, thanks to the continuous fibre being large enough as a whole to interact on a macro level. At this time no study on the relative toxic effects has been done. The review of nanocomposites from electrospun fibre by Chronakis outlines the potential benefits of the ability to produce fibrous material with a wide range of diameters and surface textures, allowing development of ideal fibre matrix interactions leading to the maximising of the potential properties of the composite [a.59]. It is also pointed out that the irregular void structure in fabrics and the ‘hairiness’ of yarns are expected to take advantage of the mechanical interlocking mechanism of load transfer between matrix and fibre, which would significantly enhance the performance of a composite article.
Briefly, the intrinsic high strength of the SWNT is not used to high best advantage in a composite if the mode of failure of the composite is through fibre pullout rather than fibre breakage – a short fibre is more likely to fail in the former mode. Dynamic mechanical thermal analysis of the fibres showed an increased the crystallinity of the PVOH phase associated with the presence of the carbon nanotubes, increasing the tensile strength of mats made from the material [a.77].
Chronakis cites two specific examples of electrospun fibre composites, one using aromatic heterocyclic polybenzimidazole (PBI) nanofibres and the other using Nylon-4,6 but both reinforcing an epoxy matrix. In the more detailed case of the PBI nanofibres, a 15 wt% fibre loading resulted in a reinforcing effect higher than that of PBI fibroids (whisker length particles). The PBI nanofibres were also used to reinforce a rubber matrix resulting in a 10-fold increase in the Young’s modulus and a doubling of the tear strength. However, Chronakis also notes that the control and reproducibility of orientation and the design and manufacture of processing apparatus still stands as a significant challenge in this field [a.59].
The first successful commercial use of electrospun fibre was claimed by Donaldson Inc., for filtration elements (http://www.donaldson.com/en/filtermedia/ nanofibres/ accessed on 19th July 2008). Donaldson Co. Inc., have been developing electrospun nanofibre filtration elements Ultra-Web® filters for dust collection, Spider-Web® filters for gas turbine air filtration, and Donaldson Endurance™ air filters for heavy-duty engines since the 1970s and are probably the highest volume producers of nanofibre-based filtration media. In performance fabrics, Korean nanofibre manufacturer, Finetex Technology Global Limited made a distribution agreement with US-based Polartec, LLC in March 2008 to supply 17 million m2 of nanofibres over the next 7 years to Polartec Ltd (http://www.finetextech.com accessed on 19th July 2008).
The electrospun fibre itself can be treated as a composite material. The paper by Li and Xia demonstrates the method of using a co-axial electrospinning head that allows the production of a core-sheath co-axial fibre [a.48]. In this example both the core and sheath is made from solid fibre. In the paper by Xu and co-workers electrospinning is done from an emulsion that results in a similar core-sheath co-axial structure where the core is a fluid and the sheath is solidified polymer [a.68]. Further to this there is also work done by Ko and co-workers (629) that uses the incorporation of carbon nanotubes dispersed in the polymer solution to reinforce the electrospun fibres to enhance their performance [a.62]. Naebe and co-workers seek to overcome the inherent disadvantage of carbon nanotubes of short length by incorporating single walled carbon nanotubes (SWNT) into electrospun polyvinyl alcohol (PVOH) nanofibres.
Belcher and Lee have produced long rod-shaped M13 viruses in electrospun PVP (polyvinylpyrrolidone) fibres: the ultimate aim of this work is to produce materials with controlled electrical, mechanical or magnetic properties. The viruses are still biologically viable after the spinning process [a.78].
4.6 Industrial Applications
Studies have shown that a low fibre diameter allows a filter element with similar operational characteristics but with much higher filtration performance. Beyond this there is also the potential for the incorporation of biologically or chemically active elements either on the surface of the fibre, or intrinsic to the structure of the fibre allowing for active filtration to occur. Active filtration implies that the entrapment method is based on chemical attraction rather than simple physical entanglement. The advantages of this method are a lower resistance to flow across the filter element, and the possibility of selectivity so that particular elements can be removed during filtration. Using a high specific surface area as a site for chemical reactions shows clear potential as a delivery technology
23
Electrospinning
for catalysts. Due to the high surface area to volume ratio there would be minimal waste of catalysts that operate by surface reaction kinetics rather than playing an active role in the chemical reaction. It has been shown by Viswanathamurthi and co-workers, and Ding and co-workers that it is possible to include metal salts in the electrospinning solution and perform a thermal post-treatment that removes the polymer carrier and leaves a metal oxide [a.80] (640). For more complex metal catalysts the work by He and Gong (640) shows that multiple metal salts can be incorporated, with the final fibre having a mixed composition [a.81].
from lower operating voltages. However, they can store relatively large quantities of energy for short periods of time. As they can be produced with a very high energy density (energy per unit mass of storage medium) they have been proposed as an energy source for electric vehicles. They could also be used as cheap power sources for mobile appliances that are frequently used such as cellphones or portable media players. This would increase the number of times they need to be charged but with low power operation this could only demand daily charging similar to modern devices.
Another important industrial application being explored is the use of electrospun fibre as a substrate for the biological element in a bioreactor. Again due to the large surface area to volume ratio and the general strength of these small fibres it is possible to create a substrate that allows a high density of biologically active material such as cells to be packed into a small space while still permitting the flow of nutrient. The higher the density of the biologically active material, the better the efficiency per volume that the bioreactor should be able to achieve. A further advantage for the electrospinning process is the ability to form a surface texture from small pores (597) that could act as anchoring points for cells in the bioreactor [a.82].
The work by Kim and Yang has explored the possible application of electrospun polyacrylonitrile fibres for super capacitor manufacture (65). It was found that using a steam activation method on the fibre membrane one could produce a suitable electrode for a capacitor with a high surface area due to the formation of pores on the fibre structure. It was observed that the electrode manufactured by this method had a specific capacitance of 120 F/g while sustaining a discharge current of 1000 mA/g. In this case the specific capacitance did vary by 18% over the range from 1 to 1000 mA/g.
4.7 Electronics and Energy Applications The use of electrospun fibre in the electronics and energy industry is a growing area, and a number of interesting applications have been pursued. Work by Kim and co-workers has been exploring the use of electrospun fibre as one of the elements in lithium polymer batteries [a.82]. It was found that electrospun polyvinyl di-fluoride fibres were suitable as a highly porous membrane that showed good high temperature (60 oC) performance when used in a lithium polymer battery. The high temperature performance would enable lithium polymer batteries to operate at a higher discharge rate and have a better performance cycle. A patent by Best and co-workers describes a method for using electrospun fibre to manufacture a flexible battery that may become integral to the flexible electronics industry [a.83]. The high surface specific area of electrospun fibres may find application in the production of super capacitors [a.84]. Super capacitors have a much larger capacitance than those traditionally used in modern electronics although at the time of writing they suffer
24
Using the method of co-axial electrospinning it would be possible to produce a core-sheath structure that would consist of a conducting core polymer and an insulating sheath. These fibres could then act as insulated nanowires. The same sintering process used in the production of metal oxide fibres can also be used to manufacture conductive gold nanowires when a suitable metal salt is introduced to the polymer solution as described by Pol and co-workers (65) [a.86]. As yet the steps beyond the synthesis of the raw nanowire, allowing the manufacture of more complex nanoscale electronics, are unknown to the authors. However, these nanowires may find application in the manufacture of cheap chemical sensors where the nanowires are used to connect the sensor element to the processing circuit. It could also be possible to use the electrospun fibre as the sensor element as well as the transmission medium. The patent by Han and co-workers describes a method of using electrospun fibre to manufacture numerous chemical sensors for different chemical species to be used in a device described as an ‘electronic nose’ [a.86].
Electrospinning
5 MATERIALS Solvents
Typical Processing Parameters
Processing Parameter Range
References
Synthetic Polymers Poly(ethylene oxide) (PEO) Water, Acetone (658) Chloroform, Ethanol, N,N – Dimethylformamide (DMF) (594) 0.5 M Acetic Acid [a.88] Water/Methanol (90:10) [a.89] Water/Ethanol (60:40) [a.90]
Concentration: ~10% (656) Molecular Weight: ~400,000 (679) Voltage: 10 kV – 20 kV (594) Distance: ~15 cm (679) Electric Field: 0.5 kV/cm – 1 kV/cm [a.91]
Concentration: 1% [a.92] – 10% (678) Mw: 300,000 [a.93] – 2,000,000 (677) Voltage: 1 kV [a.93] – 30 kV [a.94] Distance: 5 cm [a.94] – 40 cm (535) Electric Field: 0.2 [a.92] – 3.2 kV/cm (593)
[a.88-a.98], (682), (679), (678), (677), (656), (592), (594), (593), (580), (535)
Concentration: ~ 8% [a.100] Molecular Weight: ~ 80,000 [a.101] Voltage: ~ 20 kV {860262} Distance: ~ 10 cm [a.102] Electric Field: ~ 1.5 kV/cm (369)
Concentration: 4.1% [a.103] – 18% Concentration: 2.8e-7 mol/l (663) – 2.9e-6 mol/l (571) Mw: 10,000 (595) 185,000 [a.99] Voltage: 5 kV (571) – 100 kV (595) Distance: 3.5 cm [a.104] – 25 cm (580) Electric Field: 0.3 kV/cm – 4 kV/cm (571)
[a.99-a.106], (663), (642), (596), (595), (580), (571), (564), (435), (369)
Concentration: ~20% [a.107] Molecular Weight: 200,000 – 300,000 (543) Voltage: ~30 kV (275) Distance: ~15 cm (333) Electric Field: ~1 kV/cm [a.108]
Concentration: 2.5% (283) – 35% (597) Concentration: 1.4e-8 mol/l (283) – 1.7e-5 mol/l (597) Mw: 4,000 – 1,880,000 (333) Voltage: 3 kV [a.108] – 30 kV (558) Distance: 3 cm [a.108] – 35 cm (597) Electric Field: 0.14 kV/cm (656) – 3 kV/cm (275)
[a.107, a.108], (680), (656), (597), (543), (558), (526), (333), (283), (275)
Poly(vinyl alcohol) (PVOH) Water [a.99] Ethanol/Water (1:1) (595) Aqueous Acetic Acid (369)
Polystyrene (PS) DMF, Toluene (656) Carbon Disulfide (CS2) (275) Chloroform, Tetrahydrofuran (THF), Methylethylketone (543) Acetic Acid (558)
25
Electrospinning
Polyacrylonitrile (PAN) DMF (531)
Concentration: 10% [a.109] Molecular Weight: ~75,000 [a.110] Voltage: 10-25 kV [a.109] Distance: ~16 cm (372) Electric Field: ~1.7 kV/cm (628)
Concentration: 4% (292) – 14% [a.111] Concentration: 3.8e-4 mol/l – 3.2e-3 mol/l (400) Mw: 55,000 (400) – 210,000 (531) Voltage: 5 kV [a.110] – 40 kV (292) Distance: 10 cm – 30 cm (400) Electric Field: 0.3 kV/cm (372) – 3 kV/cm (400)
[a.109-a.111], (628), (531), (400), (372), (292)
Concentration: ~10% (595) Molecular Weight: ~80,000 [a.112] Voltage: ~15 kV (539) Distance: ~12 cm [a.59] Electric Field: ~1 kV/cm [a.60]
Concentration: 5% [a.114] – 12% [a.115] Concentration: 2.5e-4 [a.114] – 1.3e-3 [a.112] Mw: 80,000 (595) – 200,000 [a.114] Voltage: 12 kV (595) – 20 kV [a.114] Distance: 10 cm [a.114] – 15 cm (539) Electric Field: 1 kV/cm (539) – 2 kV/cm [a.115]
[a.112-a.115], (595), (539)
Concentration: 3% (526) – 40% (664) Concentration: 4.5e-5 (526) – 4.0e-3 (664) Mw: 48,000 (615) – 670,000 (526) Voltage: 20 kV (664) – 41 kV [a.116] Distance: 15 cm (628) – 20 cm (615) Electric Field: 0.75 kV/cm (615) kV/cm [a.116]
[a.116], (664), (628), (615), (526)
Biopolymers Polycaprolactone (PCL) Chloroform/Methanol (3:1) (539) Toluene/Methanol (1:1), Dichloromethane/Methanol (3:1), Acetone (595)
Polylactic acid (PLA, PLLA, PDLA) DMF, DMF/Methylene chloride (664) Dichloromethane (526) Dichloroethane, Chloroform (615)
26
Concentration: ~10% (615) Molecular Weight: ~109,000 (664) Voltage: ~25 kV (628) Distance: ~15 cm (664) Electric Field: ~2 kV/cm (664)
Electrospinning
Cellulose Acetate (CAc) Acetone/ Dimethylacetimide (DMAc) (2:1) (596) Acetone/water (5-20% wt water) (608) Acetic Acid [a.117] DMF [a.118]
Concentration: ~16% [a.118] Molecular Weight: 30,000 [a.117] Voltage: ~16 kV (106) Distance: ~15 cm (596) Electric Field: ~1.3 kV/cm (596)
Concentration: 3% (106) – 21% (608) Concentration: 6.0e-4 (106) – 7.0e-3 (608) Mw: 30,000 (608) – 50,000 (106) Voltage: 8 kV (608) – 25 kV [a.117] Distance: 6 cm (608) – 45 cm (106) Electric Field: 0.4 kV/cm (106) – 2.5 kV/cm [a.117]
[a.117, a.18], (596), (608), (106),
Concentration: ~10% [a.112] Voltage: ~15 kV [a.112] Distance: ~12 cm [a.120] Electric Field: ~1 kV/cm [a.119]
Concentration: 5% [a.120] – 29% [a.121] Voltage: 10 kV [a.119] – 28 kV [a.122] Distance: 10 cm [a.119] – 15 cm [a.121] Electric Field: 0.8 kV/cm [a.120] – 1.3 kV/cm [a.120]
[a.112], [a.119-a.122],
Concentration: ~25% (481) Voltage: ~20 kV [a.123] Distance: ~10 cm (63) Electric Field: ~2 kV/cm (319)
Concentration: 17% (63) – 50% (319) Voltage: 8 kV (481) – 40 kV (256) Distance: 5 cm (256) – 25 cm [a.123] Electric Field: 0.5 kV/cm [a.123] – 4 kV/cm (256)
[a.123], (481), (319), (256), (63)
Polymer Temp: ~285 OC (339) Molecular Weight: ~200,000 [a.124] Voltage: ~20 kV [a.124] Distance: ~4 cm [a.124] Electric Field: ~ 5 kV/cm [a.124]
Polymer Temp: 200 OC (569) – 320 OC [a.124] Mw: 14,000 – 580,000 (569)Voltage: 10 kV (339) – 30 kV (569) Distance: 2 cm (569) – 7 cm (339) Electric Field: 1.4 kV/cm (339) – 15 kV/cm (569)
[a.124], (339), (569)
Gelatin 1,1,1,3,3,3 - Hexafluoro-2propanol [a.119] 2,2,2 – Trifluroethanol [a.120] Acetic Acid, Formic Acid [a.121]
Zein Ethanol/Water (4:1) (481) Acetic Acid, Isopropyl Alcohol/Water (4:1), Ethanol/Water (3:2) (256) DMF [a.123]
Melt Spinning Polypropylene (PP)
27
Electrospinning
References a.1.
a.12.
A. Formhals, Richard Schreiber-Gastell, assignee; Method and Apparatus for Spinning, USA, 1939.
W. Gilbert, De Magnete, Magneticisque Corporibus, et de Magno Magnete Tellur (On the Magnet and Magnetic Bodies, and on That Great Magnet the Earth), Peter Short, London, UK, 1628.
a.13. A. Formhals, Inventor; Richard SchreiberGastell, assignee; Method of producing artificial fibres, USA, 1939.
a.2.
J.F. Cooley, inventor; no assignee; Apparatus for electrically dispersing fluids, US 692631, 1902.
a.14. A. Formhals, Richard Schreiber-Gastell, assignee; Artificial Thread and Method of Producing Same, USA, 1940.
a.3.
J. Zeleny, The Electrical Discharge from Liquid Points, and A Hydrostatic Method of Measuring the Electric Intensity at their Surfaces, Physical Review, 1914, 3, 2, 69.
a.15. A. Formhals, inventor; Production of Artificial Fibres from Fiber forming Liquids, USA, 1943.
a.4.
G. Taylor, Disintegration of Water Drops in an Electric Field, Proceedings of the Royal Society of London, Series A: Mathematical and Physical and Sciences, 1964, 280, 1382, 383.
a.5.
a.6.
a.7.
a.17.
G. Taylor, The force exerted by an electric field on a long cylindrical conductor, Proceedings of the Royal Society of London, Series A: Mathematical and Physical Sciences, 1965, 291, 1425, 145.
E.K. Gladding, inventor; Apparatus for the production of filaments, threads, and the like, EI DuPont de Nemours & Company, assignee; US 2168027, 1939.
a.18.
G . Ta y l o r, E l e c t r i c a l l y D r i v e n Je t s , Proceedings of the Royal Society of London Series A: Mathematical and Physical Sciences, 1969, 313, 1515, 453.
J. Doshi and D.H. Reneker, Electrospinning Process and Applications of Electrospun Fibres, Journal of Electrostatics, 1995, 35, 2-3, 151.
a.19.
Z-M. Huang, Y-Z. Zhang, M. Kotaki and S. Ramakrishna, A review on polymer nanofibres by electrospinning and their applications in nanocomposites, Composites Science and Technology, 2003, 63, 15, 2223.
a.20.
S.N. Reznik, A.L. Yarin, A. Theron and E. Zussman, Transient and steady shapes of droplets attached to a surface in a strong electric field, Journal of Fluid Mechanics, 2004, 516, 1, 349.
a.21.
M.M. Hohman, M. Shin and G. Rutledge, Electrospinning and electrically forced jets, I, Stability theory, Physics of Fluids, 2001, 13, 8, 2201.
a.22.
A.L. Yarin, S. Koombhongse and D.H. Reneker, Bending instability in electrospinning of nanofibres, Journal of Applied Physics, 2001, 89, 5, 3018.
J . R . M e l c h e r a n d G . I . Ta y l o r , Electrohydrodynamics: A Review of the Role of Interfacial Shear Stresses, Annual Review of Fluid Mechanics, 1969, 1, 1, 111.
a.8.
W.J. Morton, inventor; no assignee; Method of dispersing fluids, US 705691, 1902.
a.9.
C.L. Norton, inventor; no assignee; Method of and apparatus for producing fibrous or filamentary material, Massachusetts Institute of Technology, US 20486513, 1936.
a.10.
a.11.
28
a.16. A. Formhals, inventor; no assignee; Method and Apparatus for Spinning, US 2349950, 1944.
A. Formhals, inventor; no assignee; Process and Apparatus for Preparing Artificial Threads, US 1975504, 1934. A. Formhals, inventor; no assignee; Artificial Fibre Construction, US 2109333, 1938.
Electrospinning
a.34.
CRC Handbook of Chemistry and Physics, 84th Edition Ed., D.R. Lide, CRC Press, Boca Raton, FL, USA, 2003.
A . F. S p iva k , Y. A . D z e n i s a n d D . H . Reneker, A Model of Steady State Jet in the Electrospinning Process, Mechanics Research Communications, 2000, 27, 1, 37.
a.35.
D. Halliday, R. Resnick and J. Walker, Fundamentals of Physics, 6th Edition, John Wiley & Sons, New York, NY, USA, 2001.
P. Tabeling, Introduction to Microfluidics, Oxford University Press, Oxford, UK, 2005.
a.36.
L.C. Headley, C.I. Pierce and W.K. Sawyer, Fluid flow in channels, capillaries and porous media under the influence of an electric field, Washington, United States Department of the Interior, Bureau of Mines, USA, 1970.
Y.M. Shin, M.M. Hohman and M.P. Brenner, Electrospinning: A whipping fluid jet generates submicron polymer fibres, Applied Physics Letters, 2001, 78, 8, 1149.
a.37.
A.L. Yarin, Free Liquid Jets and Films: Hydrodynamics and Rheology, Longman Scientific and Technical, New York, NY, USA, 1993.
a.38.
S. Zhao, X. Wu, L. Wang and Y. Huang, Electrospinning of Ethyl–Cyanoethyl Cellulose/Tetrahydrofuran Solutions, Journal of Applied Polymer Science, 2004, 91, 1, 242.
a.39.
A. Koski, K. Yim and S. Shivkumar, Effect of molecular weight on fibrous PVA produced by electrospinning, Materials Letters, 2004, 58, 3-4, 493.
a.40.
G.C. Rutledge, M.Y. Shin, S.B. Warner, A. Buer, M. Grimler and S.C. Ugbolue, A Fundamental Investigation of the Formation and Properties of Electrospun Fibres, National Textile Center Annual Report, National Textile Center, PA, USA, 2001.
a.23.
J.M.G. Cowie, Polymers: Chemistry and Physics of Modern Materials, 2nd Edition, Blackie, New York, NY, USA, 1991.
a.24.
a.25.
a.26.
a.27.
a.28.
a.29.
H. Anton, Calculus: A New Horizon, 6th Edition Wiley, New York, NY, USA, 1999. D.H. Reneker, A.L. Yarin, H. Fong and S. Koombhongse, Bending instability of electrically charged liquid jets of polymer solutions in electrospinning, Journal of Applied Physics, 2000, 87, 9, 4531. S. Ramakrishna, K. Fujihara, W-E. Teo, T-C. Lim and Z. Ma, An Introduction to Electrospinning and Nanofibres, World Scientific, Singapore, Malaysia, 2006.
a.30.
C.J. Thompson, G.G. Chase, A.L. Yarin and D.H. Reneker, Effects of parameters on nanofiber diameter determined from electrospinning model, Polymer, 2007, 48, 23, 6913.
a.31.
R.S. Carson, C.D. Hendricks, Jr., J.J. Hogan and J.M. Schneider, Photo-micrography of electrically sprayed heavy particles, AIAA Journal, 1964, 2, 4, 733.
a.41.
W.E. Teo and S. Ramakrishna, Electrospun fibre bundle made of aligned nanofibres over two fixed points, Nanotechnology, 2005, 16, 9, 1878.
a.32.
A.L.Yarin, S. Koombhongse and D.H. Reneker, Taylor cone and jetting from liquid droplets in electrospinning of nanofibres, Journal of Applied Physics, 2001, 90, 9, 4836.
a.42.
G. Larsen, R. Spretz and R. Velarde-Ortiz, Use of coaxial gas jackets to stabilise Taylor cones of volitile solutions and to induce particle-to-fibre transitions, Advanced Materials, 2004, 16, 2, 166.
a.33.
G. K. Batchelor, An Introduction to Fluid Dynamics, Cambridge University Press, Cambridge, UK, 2000.
a.43.
A.L. Andrady and D.S. Ensor, Electrospinning in a controlled gaseous environment, Research Triangle Park, NC, USA, 2007.
29
Electrospinning
a.44.
P.K. Baumgarten, Electrostatic Spinning of Acrylic Microfibres, Journal of Colloid and Interface Science, 1971, 36, 1, 71.
a.45.
a.46.
a.54.
D. Fang, B.S. Hsiao and B. Chu, Multiplejet Electrospinning of Non-woven Nanofiber Articles, Polymer Preprints, 2003, 44, 59.
B . S u n d a r a y, V. S u b r a m a n i a n , T. S . Natarajan, R-Z. Xiang, C-C. Chang and W-S. Fann, Electrospinning of continuous aligned polymer fibres, Applied Physics Letters, 2004, 84, 7, 1222.
a.55.
S. Games, Method and apparatus for making glass wool, Owens Illinois Glass Co., USA, 1938.
P.M. Ajayan, L.S. Schadler and P.V. Braun, Nanocomposite Science and Technology, Wiley-VCH, Weinheim, Germany, 2003.
a.56.
L. Moroni, R. Licht, J. De Boer, J.R. De Wijn and C.A. Van Blitterswijk, Fiber diameter and texture of electrospun PEOT/ PBT scaffolds influence human mesenchymal stem cell proliferation and morphology, and the release of incorporated compounds, Biomaterials, 2006, 27, 28, 4911.
a.57.
N. Bhattarai, D. Edmondson, O. Veiseh, F.A. Matsen and M. Zhang, Electrospun ch i t o s a n - b a s e d n a n o fi b re s a n d t h e i r cellular compatibility, Biomaterials, 2005, 26, 31, 6176.
a.58.
M. Li, Y. Guo, Y. Wei, A.G. Macdiarmid and P.I. Lelkes, Electrospinning polyanilinecontained gelatin nanofibres for tissue engineering applications, Biomaterials, 2006, 27, 13, 2705.
a.59.
I.S. Chronakis, Novel nanocomposites and nanoceramics based on polymer nanofibres using electrospinning process - A review, Journal of Materials Processing Technology, 2005, 167, 2-3, 283.
a.60.
J.J. Feng, The stretching of an electrified nonNewtonian jet: A model for electrospinning, Physics of Fluids, 2002, 14, 11, 3912.
a.61.
F.O. Anderegg, Strength of Glass Fibre, Industrial Engineering Chemistry, 1939, 31, 3, 290.
a.62.
J.H. Wendorff, Electrospinning of Nanofibres: Towards New Techniques, Functions and Applications, in Proceedings of the 29th Australasian Polymer Symposium, Hobart, Tasmania, 2007.a.63. P.Viswanathamurthi, N. Bhattarai, C.K.Kim, H.Y. Kim and D.R. Lee, Ruthenium doped TiO 2 fibres by electrospinning, Inorganic Chemistry Communications, 2004, 7, 5, 679.
a.47.
O. Jirsak, L. Martinova, F. Sanetrnik, J. Chaloupek, D. Lukas and V. Kotek; A method of nanofibres production from a polymer solution using electrostatic spinning and a device for carrying out the method, WO2005/024101A1, 2005.
a.48.
D. Li and Y. Xia, Direct Fabrication of Composite and Ceramic Hollow Nanofibres by Electrospinning, Nano Letters, 2004, 4, 5, 933.
a.49.
Y. Yang, Z.D. Jia, L. Hou, Q.A. Li, L.M. Wang and Z.C. Guan, Controlled deposition of electrospinning jet by electric field distribution from an insulating material surrounding the barrel of the polymer solution, IEEE Transactions on Dielectrics and Electrical Insulation, 2008, 15, 1, 269.
a.50.
a.51.
F. Dabir ian , Y. H o s s ein i an d S . A. H . Ravandi, Manipulation of the electric field of electrospinning system to produce polyacrylonitrile nanofiber yarn, Journal of the Textile Institute, 2007, 98, 3, 237. B.K. Gu, M.K. Shin, K.W. Sohn, S.I. Kim, S.J. Kim, S-K. Kim, H. Lee and J.S. Park, Direct fabrication of twisted nanofibres by electrospinning, Applied Physics Letters, 2007, 90, 26, 263902.
a.52.
S. Chuangchote and P. Supaphol, Fabrication of aligned poly(vinyl alcohol) nanofibres by electrospinning, Journal of Nanoscience and Nanotechnology, 2006, 6, 1, 125.
a.53.
L. Liu and Y.A. Dzenis, Analysis of the effects of the residual charge and gap size on electrospun nanofibre alignment in a gap method, Nanotechnology, 2008, 19, 35, 355307.
30
Electrospinning
a.64.
O. Siniaguine, Wound Dressing and Apparatus for forming the same, PolyRemedy Inc, USA, 2006.
a.65.
G. Larsen, R. Spretz and R. Velarde-Ortiz, Method of Manufacturing Fibrous Hemostatic Bandages, USA, 2007.
a.66.
D.L. Kaplan and M. Lorenz, Silk-Based Drug Delivery System, Trustees of Tufts College, USA, 2008.
a.67.
G. Verreck, I. Chun, J. Rosenblatt, J. Peeters, A. Van Dijck, J. Mensch, M. Noppe and M.E. Brewster, Incorporation of drugs in an amorphous state into electrospun nanofibres composed of a water-insoluble, nonbiodegradable polymer, Journal of Controlled Release, 2003, 92, 3, 349.
a.75.
A. Shalev, Implantable Bioreactors and Uses Thereof, Nicast Ltd, USA, 2008.
a.76.
H. Schreuder-Gibson, W. Yeomans and J. Walker, Analysis Methodologies for Studies of Reactions Between Simulants and Self-Detoxifying Fabric Materials Poster Presented at the Denver DECON Science and Technology Conference, Westminster, CO, USA, 2006.
a.77.
M. Naebe, T. Lin, M.P. Staiger, L. Dai and X. Wang, Electrospun single-walled carbon nanotube/polyvinyl alcohol composite nanofibres: structure property relationships, Nanotechnology, 2008, 19, 30, 305702.
a.78.
A.M. Belcher and S-W. Lee, Viral Fibres, USA, 2008.
a.68.
J. Zeng, X. Xu, X. Chen, Q. Liang, X. Bian, L. Yang and X. Jing, Biodegradable electrospun fibres for drug delivery, Journal of Controlled Release, 2003, 92, 3, 227.
a.79.
B. Ding, C.K. Kim, H.Y. Kim, M.K. Se and S.J. Park, Titanium dioxide nanoribers prepared by using electrospinning method, Fibres and Polymers, 2004, 5, 2, 105.
a.69.
P. Gingras, Tissue Scaffold, International, Proxy Biomedical Ltd, 2006.
a.80.
a.70.
F. Guilak and F. Moutos, Three-Dimensional Fiber Scaffolds for Tissue Engineering, International, Duke University, 2006.
P. Viswanathamurthi, N. Bhattarai, H.Y. Kim and D.R. Lee, Vanadium pentoxide nanofibres by electrospinning, Scripta Materialia, 2003, 49, 6, 577.
a.81.
M.S. Shindler and H.Y. Chung, Nanofibrillar Structure and Applications Including Cell and Tissue Culture, USA, 2005.
a.82.
J.R. Kim, S.W. Choi, S.M. Jo, W.S. Lee and B.C. Kim, Electrospun PVdF-based fibrous polymer electrolytes for lithium ion polymer batteries, Electrochimica Acta, 2004, 50, 1, 69.
a.83.
A.S. Best, G.A. Snook, A.G. Pandolfo, A.F. Hollenkamp, I.L. Kyratzis and R.J.N. Helmer, Flexible Energy Storage Devices, International, Commonwealth Scientific and Industrial Research Organisation, 2007.
a.84.
T. Maruyama and A. Kamakura, Electrode for Capacitor and Electric Double Layer Capacitor using the same, The Yokohama Rubber Co. Ltd, USA, 2008.
a.85.
C. Kim and K.S. Yang, Electrochemical properties of carbon nanofiber web as an electrode for supercapacitor prepared by
a.71.
P. Neuenschwander, Scaffolds for Artificial Heart Valves and Vascular Structures, International, Eidgenossische Technische Hochschule Zurich, 2007.
a.72.
V.P. Shastri and J. Sy, Nano- and Microscale Engineering of Polymeric Scaffolds for Vascular Tissue Engineering, USA, 2006.
a.73.
H.H. Lu, J. Spalazzi and K. Dionisio, Multiphased, Biodegradable and Osteointegrative Composite Scaffold for Biological Fixation of Musculoskeletal Soft Tissue to Bone, International, The Trustees of Columbia University in the city of New York, NY, USA, 2005.
a.74.
T.A. Bertram, A. Bruce, D. Jain, M. Jayo, J. Ludlow, D, McCoy, R. Payne and N. Sangha, Scaffolds for Organ Reconstruction and Augmentation, International, Tengion Inc, 2007.
31
Electrospinning
electrically forced jets, II, Applications, Physics of Fluids, 2001, 13, 2221-2236.
electrospinning, Applied Physics Letters, 2003, 83, 6, 1216. a.86.
L. Han, A.L. Andrady and D.S. Ensor, Polymer Nanofiber-based Electric Nose, Research Triangle Institute, USA, 2008.
a.87.
D. Li, G. Ouyang, J.T. McCann and Y. Xia, Collecting Electrospun Nanofibres with Patterned Electrodes, Nano Letters, 2005, 5, 5, 913.
a.88.
a.89.
a.90.
a.91.
a.92.
a.93.
a.94.
a.95.
32
N. Bhattarai, D. Edmondson, O. Veiseh, F.A. Matsen and M. Zhang, Electrospun chitosan-based nanofibers and their cellular compatibility, Biomaterials, 2005, 26, 6176-6184. R. Kessick and G Tepper, Microscale polymeric helical structures produced by electrospinning, Applied Physics Letters, 2004, 84, 4807-4809. D.H. Reneker, A.L.Yarin, H. Fong and S. Koombhongse, Bending instability of electrically charged liquid jets of polymer solutions in electrospinning, Journal of Applied Physics, 2000, 87, 4531-4547. Y.M. Shin, M.M. Hohman, M.P. Brenner and G.C. Rutledge, Electrospinning: A whipping fluid jet generates submicron polymer fibers. Applied Physics Letters, 2001, 78, 1149-1151. J. Doshi and D.H. Reneker, Electrospinning Process and Applications of Electrospun Fibers, Journal of Electrostatics, 1995, 35, 151-160. D. Sun, C. Chang, S. Li and L. Lin, NearField Electrospinning, Nano Letters, 2006, 6, 839-842. S. Kidoaki, I.K. Kwon and T. Matsuda, Mesoscopic spatial designs of nano- and microfiber meshes for tissue-engineering matrix and scaffold based on newly devised multilayering and mixing electrospinning techniques, Biomaterials, 2005, 26, 37-46. M.M. Hohman, M. Shin, G. Rutledge and M.P. Brenner, Electrospinning and
a.96.
Z-M. Huang, Y.Z. Zhang, M. Kotaki and S. Ramakrishna, A review on polymer nanofibers by electrospinning and their applications in nanocomposites, Composites Science and Technology, 2003, 63, 2223-2253.
a.97.
A . F. S p iva k , Y. A . D z e n i s a n d D . H . Reneker, A Model of Steady State Jet in the Electrospinning Process, Mechanics Research Communications, 2000, 27, 37-42.
a.98.
A.L. Yarin, S. Koombhongse and D.H. Reneker, Taylor cone and jetting from liquid droplets in electrospinning of nanofibers, Journal of Applied Physics, 2001, 90, 4836-4845.
a.99.
A. Koski, K. Yim and S. Shivkumar, Effect of molecular weight on fibrous PVA produced by electrospinning, Materials Letters, 2004, 58, 493-497.
a.100. H. Wang, X. Lu, Y. Zhao and C. Wang, Preparation and characterization of ZnS:Cu/ PVA composite nanofibers via electrospinning, Materials Letters, 2006b, 60, 2480-2484. a.101. H. Guan, C. Shao, B.C.J. Gong and X. Yang, Preparation and characterization of NiO nanofibres via an electrospinning technique Inorganic Chemistry Communications, 2003, 6, 1302-1303. a.102. W.K. Son, J. Ho Youk, T. Seung Lee and W.H. Park, Effect of pH on electrospinning of poly(vinyl alcohol), Materials Letters, 2005, 59, 1571-1575. a.103. C. Shao, H.Y. Kim, J. Gong, B. Ding, D.R. Lee and S-J. Park, Fiber mats of poly(vinyl alcohol)/silica composite via electrospinning. Materials Letters, 2003, 57, 1579-1584. a.104. V.N. Morozov, T.Y. Morozov and N.R. Kallenbach, Atomic force microscopy of structures produced by electrospraying polymer solutions, International Journal of Mass Spectrometry, 1998, 178, 143-159.
Electrospinning
a.105. H. Guan, C. Shao, B.C.J. Gong and X. Yang, A novel method for making CuO superfine fibres via an electrospinning technique, Inorganic Chemistry Communications, 2003, 6, 1409-1411. a.106. H. Guan, C. Shao, S. Wen, B.C.J. Gong and X. Yang, A novel method for preparing Co3O4 nanofibers by using electrospun PVA/ cobalt acetate composite fibers as precursor. Materials Chemistry and Physics, 2003, 82, 1002-1006. a.107. C. Shin, G.G. Chase and D.H. Reneker, Recycled expanded polystyrene nanofibers applied in filter media, Colloids and Surfaces A: Physicochemical and Engineering Aspects, 2005, 262, 211-215. a.108. B. Sundaray, V. Subramanian, T.S. Natarajan, R-Z. Xiang, C-C. Chang and W-S. Fann, Electrospinning of continuous aligned polymer fibers, Applied Physics Letters, 2004, 84, 1222-1224. a.109. C. Kim and K.S. Yang, Electrochemical properties of carbon nanofiber web as an electrode for supercapacitor prepared by electrospinning, Applied Physics Letters, 2003, 83, 1216-1218. a.110. C. Kim and K.S. Yang, Electrochemical properties of carbon nanofiber web as an electrode for supercapacitor prepared by electrospinning, Applied Physics Letters, 2003, 83, 1216-1218. a.111. X-H. Qin, S-Y. Wang, T. Sandra and D. Lukas, Effect of LiCl on the stability length of electrospinning jet by PAN polymer solution, Materials Letters, 2005, 59, 3102-3105. a.112. Y. Zhang, Z-M. Huang, X. Xu, C.T. Lim and S. Ramakrishna, Preparation of Core-Shell Structured PCL-r-Gelatin Bi-Component Nanofibers by Coaxial Electrospinning, Chemistry of Materials, 2004, 16, 3406-3409. a.113. R.R. Duling, R.B. Dupaix, N. Katsube and J. Lannutti, Mechanical characterization of electrospun polycaprolactone (PCL): A potential scaffold for tissue engineering,
Journal of Biomechanical EngineeringTransactions of the Asme, 2008, 130. a.114. S.J. Lee, J. Liu, S.H. Oh, S. Soker, A. Atala and J.J. Yoo, Development of a composite vascular scaffolding system that withstands physiological vascular conditions, Biomaterials, 2008, 29, 2891-2898. a.115. S.V. Fridrikh, J.H. Yu, M.P. Brenner and G.C. Rutledge, Controlling the fiber diameter during electrospinning, Physical Review Letters, 2003, 90, 144502-1. a.116. J. Zeng, X. Xu, X. Chen, Q. Liang, X. Bian, L. Yang and X. Jing, Biodegradable electrospun fibers for drug delivery, Journal of Controlled Release, 2003, 92, 227-231. a.117. S.O. Han, J.H. Youk, K.D. Min, Y.O. Kang and W.H. Park, Electrospinning of cellulose acetate nanofibers using a mixed solvent of acetic acid/water: Effects of solvent composition on the fiber diameter, Materials Letters, 2008, 62, 759-762. a.118. S. Tungprapa, I. Jangchud and P. Supaphol, Release characteristics of four model drugs from drug-loaded electrospun cellulose acetate fiber mats, Polymer, 2007, 48, 50305041. a.119. M. Li, Y. Guo, Y. Wei, A.G. Macdiarmid and P.I. Lelkes, Electrospinning polyaniline-contained gelatin nanofibers for tissue engineering applications, Biomaterials, 2006, 27, 2705-2715. a.120. Z-M. Huang, Y.Z. Zhang, S. Ramakrishna and C.T. Lim, Electrospinning and mechanical characterisation of gelatin nanofibers, Polymer, 2004, 45, 5361-5368. a.121. P. Songchotikunpan, J. Tattiyakul and P. Supaphol, Extraction and electrospinning of gelatin from fish skin, International Journal of Biological Macromolecules, 2008, 42, 247-255. a.122. H.M. Powell and S.T. Boyce, Fiber density of electrospun gelatin scaffolds regulates morphogenesis of dermal-epidermal skin
33
Electrospinning
substitutes, Journal of Biomedical Materials Research Part A, 2008, 84A, 1078-1086. a.123. H.L. Jiang, P.C. Zhao and K.J. Zhu, Fa b r i c a t i o n a n d ch a ra c t e r i z a t i o n o f zein-based nanofibrous scaffolds by an electrospinning method, Macromolecular Bioscience, 2007, 7, 517-525. a.124. P.D. Dalton, D. Grafahrend, K. Klinkhammer, D. Klee and M. Moller, Electrospinning of polymer melts: Phenomenological o b s e r v a t i o n s , P o l y m e r, 2 0 0 7 , 4 8 , 6823-6833.
34
References and Abstracts
Abstracts from the Polymer Library Database Item 1 Polimery 53, No.7-8, 2008, p.581. PREPARATION OF FIBERS FROM TERPOLY (ESTER-ETHER-ESTER)S BY MELT SPINNING OR ELECTROSPINNING FROM THE SOLUTION Zdebiak P; El Fray M
Item 4 Macromolecular Rapid Communications 29, No.17, 1st Sept.2008, p.1455. FIELD-DRIVEN SURFACE SEGREGATION OF BIOFUNCTIONAL SPECIES ON ELECTROSPUN PMMA/PEO MICROFIBERS Xiao-Yu Sun; Nobles L R; Borner H G; Spontak R J
Terpolymers consisting of PBTP hard segments and soft segments of dilinoleic acid residues and polyethylene glycol with different molec.wts. were prepared and melt spun or electrospun from solution into fibres. The effects of polyethylene glycol molec.wt., alpha-tocopherol (heat stabiliser) and inorganic modifier (hydroxyapatite) on melt flow rate, mechanical properties and fibre-forming properties investigated. 20 refs. Szczecinska,Politechnika
Electrospinning of polymer/peptide conjugates was used to prepare microfibres with biofunctionalised surfaces. The peptide segment was selectively driven to the surface due to contrasts in polarisability, giving the fibres the biofunctionalisation. In the example shown, a polyethylene oxide bioconjugate was blended and electrospun with polymethyl methacrylate and the resulting fibres were characterised using X-ray photoelectron spectroscopy, scanning electron microscopy and confocal microscopy of fluorescent labelled fibres. 37 refs.
EASTERN EUROPE; POLAND
Accession no.1027749 Item 2 Synthetic Metals 158, No.14, Aug.2008, p.577. FABRICATION OF POLYHEXYLTHIOPHENE/ POLYETHYLENE OXIDE NANOFIBERS USING ELECTROSPINNING Laforgue A; Robitaille L Polyhexylthiophene-polyethylene oxide blend nanofibre were produced by electrospinning from chloroform solutions. A morphological study was carried out as a function of the processing parameters as well as the ratio between the two polymers. The influence of nanofibre alignment on electrical conductivity was examined. 55 refs. Canada,National Research Council CANADA
Accession no.1027642 Item 3 Polymers for Advanced Technologies 19, No.9, Sept.2008, p.1150. PREPARATION OF THREE-DIMENSIONAL STRUCTURE CONTROLLABLE NANOFIBERS BY ELECTROSPINNING Zhang J-F; Yang D-Z; Nie J Details are given of a method of manufacturing threedimensional PVAL nanofibre with a modified collector. The size of the three-dimensional structure was controlled by process parameters. Potential applications in bio-mimic processes and micro-motor devices are mentioned. 8 refs. Beijing,University of Chemical Technology CHINA
Accession no.1027601
© Copyright 2008 Smithers Rapra Technology
North Carolina,State University; Sabic; Max-PlanckInstitut Fuer Kolloid- & Grenzflaech. EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; USA; WESTERN EUROPE
Accession no.1027594 Item 5 Journal of Polymer Science: Polymer Physics Edition 46, No.18, 15th Sept.2008 p.1903. CHARACTERIZATION OF THE STABLE AND METASTABLE POLY(ETHYLENE OXIDE)UREA COMPLEXES IN ELECTROSPUN FIBERS Yang Liu; Antaya H; Pellerin C Stable (alpha) and metastable (beta) complex nanofibres of polyethylene oxide (PEO) and urea were prepared by solution electrospinning and were characterised using wide angle X-ray scattering, differential scanning calorimetry and Fourier transform infrared spectroscopy. Fibres of both types were highly crystalline and the beta complex materials showed a stoichiometric ratio of PEO to urea of 3:2 and chains oriented along the fibre axis. A ribbon-like structure was suggested for the metastable nanofibres, with urea intercalated between PEO layers. 39 refs. Montreal,University CANADA
Accession no.1027580 Item 6 Polymer 49, No.19, 2008, p.4226-4229 ELECTROSPUN NANOFIBERS FROM A POROUS HOLLOW TUBE Varabhas J S; Chase G G; Reneker D H
35
References and Abstracts
Single electrospinning jets are known to have low production rates. A 0.1m2 nonwoven mat containing 1g of 100nm fibres may take several days to create from a single jet. Inexpensive methods of higher production rates are needed for laboratory research applications. In this paper we present experimental results of many simultaneous electrospinning jets from the surface of tube having a porous wall. The pores in the wall are small and resist the flow of the polymer. Holes drilled half way into the wall of the tube provide points of reduced flow resistance. A polymer solution of 15wt% polyvinylpyrrolidone (PVP) in ethanol is pushed by low air pressure of 1-2kPa through the tube wall at the drilled holes. On the outer surface of the tube polymer drops form at the locations of the drilled holes. The solution is charged from 40 to 60kV to electrospin the polymer. Multiple polymer jets launch from the tube surface and form fibres. A 13cm long tube with 20 holes can produce 0.3-0.5g/h of nanofibre. Production rates can easily be scaled by increasing the tube length and the number of holes. 6 refs. Akron,University USA
Accession no.1027551 Item 7 Polymer 49, No.19, 2008, p.4196. STRESS-INDUCED STRUCTURAL CHANGES IN ELECTROSPUN POLYVINYLIDENE DIFLUORIDE NANOFIBERS COLLECTED USING A MODIFIED ROTATING DISK Wu Aik Yee; Anh Chien Nguyen; Pooi See Lee; Kotaki M; Ye Liu; Boon Teoh Tan; Mhaisalkar S; Xuehong Lu By attaching separate, parallel electrodes onto a rotating disk collector, well aligned electrospun polyvinylidene difluoride (PVDF), PVDF/carbon nanotube nanocomposite and vinylidene fluoride-trifluoroethylene copolymer nanofibres are directly deposited onto flat substrates forming relatively large, uniform and compact fibrous thin films. The attachments alter the electric-field distribution on the rotating disk, which fosters the fanning of the nanofibres, while the electric field between the separate electrodes and the mechanical force exerted by the rotational disk facilitate the alignment. X-ray diffraction and infrared spectroscopic studies show that the specific environment and force fields created on the modified rotating disk cause the electrospun fibres being effectively stretched to form highly oriented beta-form crystallites with slightly reduced inter-chain distance. They also lead to slight increases in crystallinity and crystal size. A mechanism is proposed to account for the structural alteration induced by the modified rotating disk collector. Ferroelectricity of the aligned electrospun PVDF fibrous thin films is also demonstrated. 26 refs. Nanyang,Technological University; Kyoto,Institute of Technology; Singapore,Institute of Materials Research & Engineering
36
JAPAN; SINGAPORE
Accession no.1027547 Item 8 Polymer 49, No.19, 2008, p.4046. EFFECT OF SPINNING TEMPERATURE AND BLEND RATIOS ON ELECTROSPUN CHITOSAN/ POLY(ACRYLAMIDE) BLENDS FIBERS Desai K; Kit K We report the formation of non-woven fibres without bead defects by electrospinning blend solutions of chitosan and polyacrylamide (PAAm) with blend ratios varying from 75wt% to 90wt% chitosan using a modified electrospinning unit wherein polymer solutions can be spun at temperatures greater than ambient up to 100 deg.C. Electrospinning at elevated temperature leads to further expansion of the processing window, by producing fibres with fewer defects at higher chitosan weight percentage in the blends. Effects of varying blend ratios, spinning temperatures, and molecular weights on fibre formation were studied and optimum conditions for formation of uniform non-woven fibre mats with potential applications for air and water filtration were obtained. Uniform beadless fibre mats with fibre diameter as low as 307+/-67nm were formed by spinning 90% chitosan in blend solutions at 70 deg.C. 25 refs. Tennessee,University USA
Accession no.1027530 Item 9 Macromolecular Symposia No.269, 2008, p.111. NOVEL BIOLOGICALLY INSPIRED COLLAGEN NANOFIBERS RECONSTITUTED BY ELECTROSPINNING METHOD Foltran I; Foresti E; Parma B; Sabatino P; Roveri N The fabrication of self-assembled collagen nanofibres by electrospinning from an aqueous suspension of telopeptide-free collagen molecules in the absence of organic solvents and blends with natural or synthetic polymers, and their characterisation by FTIR, SEM and DSC, is described. The results are discussed in terms of potential applications as biomimetic reinforcements for new biomedical and surgical biomaterials. 33 refs. Bologna,Universita; Opocrin SpA EUROPEAN COMMUNITY; EUROPEAN UNION; ITALY; WESTERN EUROPE
Accession no.1027356 Item 10 Polymer Engineering and Science 48, No.9, 2008, p.1848. THE MORPHOLOGY, MECHANICAL PROPERTIES, AND FLAMMABILITY OF
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
ALIGNED ELECTROSPUN POLYCARBONATE (PC) NANOFIBERS Moon S; Farris R J
EUROPE; WESTERN EUROPE-GENERAL
The electrospinning of the polycarbonate (PC) solutions was performed for the variable electrospinning parameters such as polymer concentration, solvent composition, applied voltage, flow rate, and take-up velocity in order to evaluate changes of morphology, mechanical properties, and flammability of the aligned PC nanofibres as a function of the electrospinning parameters. It was found that the ratio of THF/DMF solvent in the electrospinning parameters had a major effect on the spinnability and fibre morphology. Furthermore, it was confirmed that the mechanical properties were dependent upon the fibre morphology. The spinnability of the PC solutions with a lower THF ratio in THF/DMF solvent was poor. The aligned electrospun PC fibre with the best morphology was made in the range of polymer concentration of 22%, solvent ratio of 50:50 THF : DMF, applied voltage of 14 kV, flow rate of 0.050 ml/m, and a take-up velocity of 7.3 m/s. The ultimate strength and initial modulus of the 80% drawn 22% PC fibre were 64 + - 2 MPa (commercial 5575 MPa) and 1.9 + - 0.1 GPa. The heat release capacity (HRC) of the 22 and 25% PC fibre were 275 + - 27 J/g K and 198 + - 1 J/g K. It was found that the flame resistance of the electrospun PC nanofibre was superior to that of the PC raw material (HRC ~360 J/g K). 16 refs.
Item 12 Polymer International 57, No.10, Oct.2008, p.1194. EFFECT OF ELECTRIC POTENTIAL AND COULOMBIC INTERACTIONS ON ELECTROSPINNING NANOFIBER DISTRIBUTION Jian-Feng Zhang; Dong-Zi Yang; Jun Nie
Massachusetts,University USA
Accession no.1027324 Item 11 Polymer Engineering and Science 48, No.9, 2008, p.1661. ELECTROSPINNING AND ALIGNMENT OF POLYANILINE-BASED NANOWIRES AND NANOTUBES Attout A; Yunus S; Bertrand P Polyaniline (PANi) nanowires and nanotubes are processed by electrospinning. Nanowires are electrospinned using PANi/PEO and PANi/PMMA polymer blends. The morphology and composition of these nanofibres are determined by scanning electron microscopy (SEM) and Nano-Secondary Ion Mass Spectrometry (Nano-SIMS). The conductive polymer seems more homogeneously distributed for the PANi/PEO than for the PANi/PMMA blend nanowires, which exhibit a phase separation. On the other hand, pure PANi nanotubes are prepared using PMMA nanowires as a template. The synthesis is followed by X-ray photoelectron spectroscopy (XPS), SEM and Nano-SIMS. Moreover, a simple method based on electrostatic steering allows us to align these fibres on a substrate. 23 refs. Louvain,Universite Catholique BELGIUM; EU; EUROPEAN COMMUNITY; EUROPEAN ECONOMIC COMMUNITY; EUROPEAN UNION; WESTERN
© Copyright 2008 Smithers Rapra Technology
Accession no.1027304
A method based on the electric potential and coulombic interactions was developed for simulation of the distribution of electrospun fibres. Two different types of electric field were investigated for electrospinning of poly(ethylene oxide), and the process was interpreted by means of schematics and physical equations. A simulation analysis based on idealised models is a convenient method for understanding the effect of distortions of the electric field induced by various types of collector. 10 refs. Beijing,University of Chemical Technology CHINA
Accession no.1027251 Item 13 Polymer International 57, No.10, Oct.2008, p.1188. FABRICATION OF PROTEIN-DOPED PLA COMPOSITE NANOFIBROUS SCAFFOLDS FOR TISSUE ENGINEERING Yuan J; Shen J; Kang I K Co-electrospinning of keratin or gelatin with polylactide (PLA) gave nanofibres that were characterised by means of field-emission scanning electron microscopy, attenuated total-reflection Fourier-transform IR spectroscopy, and an electron spectroscopy for chemical analysis. The biodegradation of mats of the electrospun fibres in the presence of trypsin solution was examined. NIH 3T3 cells adhered better and spread more on the PLA/keratin and PLA/gelatin nanofibrous mats than on blank PLA mats. The PLA/keratin and PLA/gelatin nanofibrous mats also improved the viability and proliferation of fibroblasts compared with PLA nanofibrous mats. 27 refs. Kyungpook,National University; Nanjing,Normal University CHINA; SOUTH KOREA
Accession no.1027250 Item 14 Polymer International 57, No.10, Oct.2008, p.1110. NOVEL ZEIN-BASED ELECTROSPUN FIBERS WITH THE WATER STABILITY AND STRENGTH NECESSARY FOR VARIOUS APPLICATIONS Xu W; Karst D; Yang W; Yang Y
37
References and Abstracts
Attempts were made to improve the tenacity of zein fibres by electrospinning fibres containing various concentrations of zein, citric acid and sodium hypophosphite monohydrate (SHP); the SHP catalyses the crosslinking of the zein by citric acid. The resulting fibres showed as much as a tenfold increase in wet tenacity and a 15-fold increase in dry tenacity compared with normal electrospun zein fibres. The average diameter of the fibres was 451 nm, the smallest reported for a zein-based electrospun fibre. A mat of this fibre retained its fibrous structure when immersed in water, and the fibre retained about 70% of its tenacity after 16 days at 50 deg.C and 90% relative humidity. 20 refs. Nebraska-Lincoln,University USA
Accession no.1027240
magneto-electrospinning and bubble-electrospinning. The use of a representative non-ionic surfactant, TritonR X-100, to enhance electrospinnability was studied. The surfactant was added to an electrospun polyvinyl pyrrolidone solution, and a dramatic reduction in surface tension was observed. As a result, a moderate voltage was needed to produce fine nanofibres, which are commonly observed during the conventional electrospinning procedure only at elevated voltage. The novel strategy thus produced smaller nanofibres than those obtained without surfactants, and the minimum threshold voltage was much decreased. A simple theoretical prediction method for the average diameter of the nanofibres under different surfactant concentrations was developed. 30 refs. Shanghai,Donghua University CHINA
Item 15 International Polymer Processing 23, No.4, Sept.2008, p.377. EFFECT OF ELECTRIC CURRENT ON BEADS FORMATION IN ELECTROSPINNING OF POLY(VINYL ALCOHOL) Kadomae Y; Amagasa M; Sugimoto M; Taniguchi T; Koyama K The effects of electric current on formation of beads in electrospinning were investigated by changing the electrical conductivity of a PVAl aqueous solution and spinning conditions, such as applied voltage, distance between a tip of needle and a collector, and relative humidity. From the results of experiments conducted by changing the conductivity of PVAl aqueous solution and spinning conditions, it was found that bead formation was suppressed at a lower electric current. Furthermore, when the electrospinning was performed at a certain constant electric current under various spinning conditions where the applied voltage and tip-collector distance were changed in order to give the same constant electric current, the resultant PVAl fibres had no beads and almost the same distribution of fibre diameters. 30 refs. Yamagata,University; Japan Vilene Co.Ltd.; Japan Science & Technology Agency JAPAN
Accession no.1027078 Item 16 Polymer International 57, No.9, Sept.2008, p.1079. NON-IONIC SURFACTANTS FOR ENHANCING ELECTROSPINABILITY AND FOR THE PREPARATION OF ELECTROSPUN NANOFIBERS Shu-Qiang Wang; Ji-Huan He; Lan Xu Electrospinning is widely used to produce nanofibres, but not every polymer can be electrospun into nanofibres. To enhance electrospinnability, attention has been paid to designing new apparatus, e.g. for vibration-electrospinning,
38
Accession no.1027048 Item 17 Fibers and Polymers 9, No.2, April 2008, p.140. EFFECT OF CONCENTRATION ON ELECTROSPUN POLYACRYLONITILE(PAN) NANOFIBERS Ji-Huan He; Yu-Qin Wan; Jian-Yong Yu An allometrical scaling relationship between the diameter of electrospun nanofibre and solution concentration was established. The scaling exponent differed greatly between different polymers and the same polymer with different molecules or the same molecules with different properties. The diameter of electrospun polyacrylonitrile nanofibres increased approximately linearly with solution concentration. The experimental data were in agreement with the theoretical predictions. 17 refs. Shanghai,Donghua University CHINA
Accession no.1026996 Item 18 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.904-905, ISBN 978-08412-6276-7, ISSN 1550-6703, CD-ROM, 012 ELECTROSPUN COPOLYIMIDE NANOFIBERS WITH EXCELLENT MECHANICAL PROPERTIES PING HU; SHIULIANG CHEN; CHUYEN CHEN; GREINER A; YONGHONG LI; HAOQING HOU JIANGXI,NORMAL UNIVERSITY; MARBURG,PHILIPPS UNIVERSITY (ACS,Div.of Polymeric Materials Science & Engng.) Electrospun copolyimide fibres were prepared from 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA), p-phenylenediamine (BPA) and 4,4'-oxydianiline (ODA)
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
at a BPA/ODA ratio of 4/6. The glass transition and decomposition temperatures of the copolyimide were 293 and 501 deg.C respectively. The tensile strength of a copolyimide nanofibre belt with aligned nanofibres was 1.1 plus or minus 0.1 GPa (about twice that of the home polyimide BPDA/PPA) but the elongation at break of the copolymer nanofibre belt was 20.8% (compared with a previously reported value of only 4.9% for high strength polyimide mats). 12 refs. CHINA; EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE Accession no.1026851 Item 19 Journal of Macromolecular Science B B47, No.4, July-Aug.2008, p.735. ELECTROSPINNING OF CONTINUOUS, LARGE AREA, LATTICEWORK FIBER ONTO TWO-DIMENSIONAL PIN-ARRAY COLLECTORS Chao Pan; Yong-Hao Han; Li Dong; Jing Wang; Zhong-Ze Gu A simple approach for arraying fibres into a large area two-dimensional lattice on an ordered metal rod collector is described and applied to the fabrication of large area latticework fibre patterns composed of polyvinyl pyrrolidone-based sub-micron fibres having diameters ranging from 910 to 1300 nm. These fibre patterns have potential applications in tissue cell culture. 18 refs. Dalian,Fisheries University; Jilin,University; Nanjing,Southeast University; Dalian,Nationalities University CHINA
Accession no.1026783 Item 20 E-Polymers No.111, 2008, p.1. ELECTROSPINNING OF POLY-L-LACTIDE NANOFIBERS ON LIQUID RESERVOIR COLLECTORS Rocker T; Greiner A The fabrication of poly(L-lactide) nanofibres via electrospinning of solutions of the polymer in dichloromethane, with or without the addition of various proportions of benzyltriethylammonium chloride as conductivity modifier, was investigated using liquid reservoir collectors with distilled water and sodium chloride solutions of different concentrations as collector liquids. The nanofibres were characterised by optical microscopy and SEM, and the effects of the electrical conductivity of the polymer solution and collector liquid and of the filling level of the liquid collector reservoir on fibre diameter, porosity and morphology of the nanofibres are discussed. 11 refs.
© Copyright 2008 Smithers Rapra Technology
Marburg,Philipps Universitat EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1026437 Item 21 E-Polymers No.98, 2008, p.1. THE STRUCTURE AND PROPERTY OF THE ELECTROSPINNING SILK FIBROIN/GELATIN BLEND NANOFIBERS Bao W; Zhang Y; Yin G; Wu J The fabrication of nanofibres of blends of silk fibroin with various proportions of gelatin via electrospinning of their solutions of various concentrations in formic acid, and their characterisation by SEM, DTA, FTIR, and tensile testing, is described. The effects of solution concentration and composition on viscosity and spinnability, and of processing conditions on morphology, fibre diameter, porosity and mechanical properties of the nanofibres were investigated and the results are discussed in terms of potential biomedical applications as scaffolds for tissue engineering. 22 refs. Suzhou,University; China,Textile Information Centre CHINA
Accession no.1026424 Item 22 Polymers for Advanced Technologies 19, No.7, July 2008, p.728. EMULSION ELECTROSPINNING: COMPOSITE FIBERS FROM DROP BREAKUP DURING ELECTROSPINNING Angeles M; Hsin-Ling Cheng; Velankar S S The feasibility of electrospinning of oil-in-water type emulsions was examined. The emulsions had an aqueous solution of PEO as the continuous phase, and either mineral oil or a PS in toluene solution as the drop phase. The Taylor cones and electrified liquid jets were stable even when the emulsion drops were as large as a few tens of microns in diameter. The resulting electrospun PEO fibres incorporated the dispersed phase of the emulsion in the form of drops (in the case of mineral oil) or in the form of solid particles (in the case of PS). Mineral oil drops appeared to be completely encapsulated in the PEO fibres, whereas the PS particles were either incompletely encapsulated or covered by only a very thin layer of PEO. Calculations showed that, in both cases, the initially large emulsion drops were broken during the electrospinning process. 15 refs. Pittsburgh,University USA
Accession no.1026077 Item 23 ANTEC 2008. Proceedings of the 66th SPE Annual Technical Conference held Milwaukee, Wi., 4th-8th May 2008.
39
References and Abstracts
Brookfield, Ct., SPE, 2008, p.513-517, PDF 0009, CDROM, 012 NOVEL DUAL ELECTRODE MODE ELECTROSPINNING OF BIODEGRADABLE POLYMERS Li M; He Y; Xin C; Li Z; Li Q; Lu C; Juang Y J A higher productivity is essential for the commercialization of the electrospinning process. A new electrospinning process, dual electrode mode electrospinning, was introduced in this study. In this work, both positively and negatively charged nozzles existed in the electric field instead of the single electrode in the conventional electrospinning process. By electrospinning polyhydroxybutyrate solution via this technique, the structure of the electrospun fibres and the line speed were investigated and discussed. 8 refs.
Item 25 Macromolecules 41, No.14, July 22, 2008, p.5345. ALIGNED MATS FROM ELECTROSPUN SINGLE FIBERS Carnell L S; Siochi E J; Holloway N M; Stephens R M; Rhim C; Niklason L E; Clark R L
CHINA; USA
By incorporating an auxiliary counter electrode to create an electric field of controlled geometry and magnitude, highly aligned electrospun micro- and nanoscale fibres and pseudo-woven mats were produced through electrospinning of polyimide (CP2) or biodegradable poly(glycolic acid) (PGA). The highly aligned electrospun fibres of CP2 were of the order of 10 microns in diameter, and the interfibre spacing in the spun mats ranged from 25 to 30 microns. The electrospun aligned fibres of PGA were of the order of 500 nm in diameter with an interfibre spacing in the spun mats of 7-10 microns. High-speed videography showed that the auxiliary electrode eliminated the jet whipping and bending instability commonly associated with the electrospinning process. 30 refs.
Accession no.1025701
Durham,Duke University; Yale,University
China,Civil Aviation University; Beijing,University of Chemical Technology; New Jersey,Institute of Technology; Taiwan,National Cheng Kung University(SPE)
USA
Item 24 ANTEC 2008. Proceedings of the 66th SPE Annual Technical Conference held Milwaukee, Wi., 4th-8th May 2008. Brookfield, Ct., SPE, 2008, p.926-930, PDF 0981, CDROM, 012 FABRICATION OF NANOSTRUCTURE ELASTIC MEMBRANES BY ELECTROSPINNING GLASSY POLYMERS Martz T Penn State Erie,Behrend College (SPE) The goal of this project is to explore elastic properties in electrospun polymeric mats prepared by electrospinning glassy polymers. For this research sulphonated poly(ether ether ketone) (sPEEK) mats were created under optimal conditions using an electrospinning device. Optimal conditions pertaining to electrospinning include having the smallest fibre diameter as well as minimal beading in the sample. The mats were then subjected to a series of heat and/or vapour treatments. To classify the results, a dynamic mechanical analyzer (DMA) was used to test the electro-spun sPEEK mat samples, heat and/or vapour treated sPEEK mat samples, and sPEEK film samples. This allowed the stress-strain curves of each sample to be compared at all stages of the research. Scanning electron microscope (SEM) images were then completed to examine the quality of electro-spun mats and fibre characteristics including average fibre diameter. 2 refs. Penn State Erie, Behrend College (SPE) USA
Accession no.1025632
40
Accession no.1025327 Item 26 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.602-803, ISBN 978-0-8412-6276-7, ISSN 1550-6703, CD-ROM, 012 CONTROLLED RELEASE OF NITRIC OXIDE FROM ELECTROSPUN BIODEGRADABLE BIOCOMPATIBLE FIBERS Liu H A; Osuna H; Miller C Y; Chen J; Balkus K J Polylactic acid, a water-degradable hydrophobic material, was used to encapsulate a nitric oxide donor. The polylactic acid was fabricated via electrospinning and had a fibrous morphology with pores throughout the structure. A nitric oxide releasing material (a diazeniumdiolate or a zeolite) was encapsulated within the pores of the fibres. The fibres were fabricated into a free-standing paper which was easily manipulated and handled in an attempt to enable site specific targeting for nitric oxide release. It was shown that hydrolysis of the polymeric fibrous, porous material in an aqueous medium exposed the encapsulated nitric oxide releasing material, leading to a more controlled and sustained release. Hydrolysis of polylactic acid generated acidic monomers which regulated the pH, resulting in a more controlled nitric oxide release than in an environment in which the pH was not regulated. Further work will be done to control the thickness of the polymer fibres in order to provide more control for nitric oxide release. 14 refs.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Texas,University at Dallas (ACS,Div.of Polymeric Materials Science & Engng.) USA
Accession no.1025020
The polymer-salt-solvent interactions were characterised by FTIR, and the solution viscosity, conductivity and surface tension were measured in solutions with different salt concentrations. 29 refs. North Carolina,State University
Item 27 Journal of Applied Polymer Science 109, No.5, 5th Sept.2008, p.3390. PREPARATION AND CHARACTERIZATION OF ELECTROSPUN, BIODEGRADABLE MEMBRANES Ren J; Liu W; Zhu J; Gu S Microporous biodegradable membranes of polylactide and lactide-glycolide copolymers and blends were fabricated through electrospinning. Structures and morphologies were investigated with SEM, DSC, and X-ray diffraction. Different polymer membranes, incorporated with carmofur, were fabricated, and their drug release profiles were investigated. Potential applications in tissue engineering and drug delivery are mentioned. 18 refs. Tongji,University CHINA
Accession no.1024755 Item 28 Journal of Applied Polymer Science 109, No.5, 5th Sept.2008, p.3337. PHOTOCROSSLINKED ELECTROSPUN CHITOSAN-BASED BIOCOMPATIBLE NANOFIBERS Jin Y; Yang D; Zhou Y; Ma G; Nie J Electrospun fibres of chitosan/PVAL were crosslinked by the incorporation of photocrosslinking agent polyethylene glycol dimethacrylate and hydroxyethoxyphenylmethylpropanone photoinitiator. The photocrosslinking process of nanofibre was studied by FTIR and water resistance was investigated by SEM and water swelling measurements. Cytotoxicity and cell adhesion on electrospin membranes were determined. 18 refs. Beijing,University of Chemical Technology CHINA
Accession no.1024748 Item 29 Journal of Applied Polymer Science 109, No.5, 5th Sept.2008, p.2935. ROLE OF POLYMER-SALT-SOLVENT INTERACTIONS IN THE ELECTROSPINNING OF POLYACRYLONITRILE/IRON ACETYLACETONATE Du J; Zhang X Iron acetylacetonate was added to a polyacrylonitrile solution and the role of polymer-salt-solvent interactions in the electrospinning of ultra-fine fibres was investigated.
© Copyright 2008 Smithers Rapra Technology
USA
Accession no.1024696 Item 30 Modern Polymeric Materials for Environmental Applications, Vol. 3. Proceedings of the 3rd International Seminar held Krakow, 14-16 May 2008. Krakow, Cracow University of Technology, 2008, p.139144, ISBN 978 83 923451 6 9, 24cm, 012 ENVIRONMENTAL APPLICATIONS OF ELECTROSPUN BIOPOLYMERS AND MULTISTRUCTURED MEMBRANES Modesti M; Roso M Padova,Universita Edited by: Pielichowski K (Cracow,University of Technology) Synthesis of silver containing multi-structured nanocomposite membranes incorporating electrospun starch based biopolymers and polylactic acid to form a non-woven membrane, followed by electrospraying with a polysulphone is described. Membranes were examined using scanning electron microscopy, and their antibacterial properties were studied in-vitro against staphylococcus aureus and e-coli. Potential uses include bioactive and biodegradable applications and filters. 5 refs. EUROPEAN COMMUNITY; EUROPEAN UNION; ITALY; WESTERN EUROPE
Accession no.1024650 Item 31 Express Polymer Letters 2, No.8, 2008, p.540. PREPARATION AND CHARACTERIZATION OF ELECTROSPUN FIBERS OF NYLON 11 Dhanalakshmi M; Jog J P The fabrication of biocompatible nylon-11 nanofibre mats by electrospinning from formic acid solution, and their characterisation by SEM (fibre diameter), XRD (crystalline structure) and DSC (thermal properties and crystallinity), is described. The results are compared with those of melt-pressed and solution-cast films, and the effects of solution concentration on fibre diameter and morphology are discussed. 34 refs. Pune,National Chemical Laboratory INDIA
Accession no.1024487 Item 32 Macromolecular Rapid Communications 29, No.14, 16th July 2008, p.1231.
41
References and Abstracts
BIODEGRADABLE POLYMER NANOCYLINDERS FABRICATED BY TRANSVERSE FRAGMENTATION OF ELECTROSPUN NANOFIBERS THROUGH AMINOLYSIS Kim T G; Park T G Polylactic acid was electrospun to produce non-crystalline nanofibre that were treated with amino group-containing strong bases to fabricate semicrystalline polylactic acid nanocylinders with tunable aspect ratio. The formation of nanocylinders was attributed to the development of stacked lamellae and of the transversely oriented degradation and fragmentation of the amorphous gaps between lamellae. The aspect ratio was tunable by varying the aminolysis time and controlling nanofibre diameter. 24 refs. Korea,Advanced Institute of Science & Technology KOREA
Accession no.1023905 Item 33 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.539-541, ISBN 978-08412-6276-7, ISSN 1550-6703, CD-ROM, 012 ESTABLISHMENT OF NANOFIBER PREPARATION TECHNIQUE BY ELECTROSPINNING Miyake H; Higashiyama Y; Yamashita Y Some nanofibre electrospinning practical difficulties and their solutions are briefly discussed. Issues discussed include: the anti-bacterial effect of titania in poly(ethylene terephthalate); nozzle blockage when electrospinning concentrated chloroform solutions of poly(lactic acid); increasing output by using multiple nozzles, but which increases the difficulty of solvent removal and nozzle cleaning; and the deposition of nonwoven fibre in thicknesses > 10 mm. 5 refs. Shiga Prefecture,University (ACS,Div.of Polymeric Materials Science & Engng.) JAPAN
Accession no.1023887 Item 34 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.511-512, ISBN 978-08412-6276-7, ISSN 1550-6703, CD-ROM, 012 COAXIAL ELECTROSPINNING OF PA6/EPOXY SUPERFINE FIBERS Yan Li; Wei Wang; Qianwei Xu; Jiangwei Li
42
Superfine fibres, with a polyamide-6 (PA6) core and an epoxy resin sheath, were prepared by coaxial electrospinning. PA6 solutions containing 2-10 wt% polymer were prepared using trifluoroethanol solvent, whilst the epoxy resin solution (32 wt% concentration) was prepared using a mixture of butanone and propanediol methyl ether. A core-shell structure was obtained when using PA6 solutions of 8% concentration and above. The formation of PA6 uncoated fibres at lower concentrations was attributed to the low viscosity of the PA6 solutions and the instability of electrospinning. 9 refs. Shanghai,Tongji,University (ACS,Div.of Polymeric Materials Science & Engng.) CHINA
Accession no.1023875 Item 35 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.482-483, ISBN 978-08412-6276-7, ISSN 1550-6703, CD-ROM, 012 CARBON NANOSTRUCTURES GROWN ON CARBONIZED ELECTROSPUN NANOFIBERS BY PALLADIUM CATALYSIS Xiaoqing Xiong; Chuiling Lai; Greiner A; Reneker D H; Haoqing Hou Nanofibres were produced by electrospinning a solution containing polyacrylonitrile and palladium acetate. Carbonisation at 400-1100 deg.C gave carbon nanofibres containing palladium nanoparticles. The palladium particle size increased with increasing temperature. Carbon nanotubes were grown on the nanofibres at 800 deg.C in an atmosphere of a mixture of toluene, ethanol and chlorobenzene, or in pyridine. The nanotube lengths increased with increasing reaction time. Coiled, tubular nanofibres were formed when pyridine was used as the carbon source. 18 refs. East China,Institute of Technology; Jiangxi,Normal University; Marburg,Philipps CHINA; EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; USA; WESTERN EUROPE
Accession no.1023860 Item 36 Journal of Polymer Science: Polymer Physics Edition 46, No.15, 1st Aug.2008, p.1611. DIAMETER CONTROL OF ELECTROSPUN POLYACRYLONITRILE/IRON ACETYLACETONATE ULTRAFINE NANOFIBERS Du J; Shintay S; Zhang X The fabrication of ultrafine nanofibres of polyacrylonitrile with various proportions of iron acetylacetonate by
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
electrospinning under various processing conditions from solutions in dimethyl formamide, characterised by viscosity and surface tension, was investigated and the nanofibres were analysed by FTIR and FE-SEM. The effects of solution properties including viscosity, conductivity and surface tension, and operating conditions, such as voltage, feed rate, and spinneret-collector distance, on the structure and diameter of the nanofibres were studied and the results are discussed. 30 refs. North Carolina,State University USA
Accession no.1023786 Item 37 Polymer Engineering and Science 48, No.7, 2008, p.1296. COCONTINUOUS CELLULOSE ACETATE/ POLYURETHANE COMPOSITE NANOFIBER FABRICATED THROUGH ELECTROSPINNING Tang C; Chen P; Liu H Cocontinuous cellulose acetate (CA)/polyurethane (PU) composite nanofibres were obtained through electrospinning of partially miscible CA and PU in 2:1 N,N-dimethylacetamide (DMAc)/acetone mixture solvent. Their structures, mechanical, and thermal properties were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC). The structures and morphologies of the nanofibres were affected by component ratio in the binary mixtures. PU component not only facilitated the electrospinning of CA at CA concentration down to 12 wt%, but reinforced the tensile strength of CA/PU nanofibrous mats, while semirigid component CA in the composite nanofibres could greatly improve the rigidity and dimensional stability of CA/ PU nanofibrous mats. In a series of nanofibrous mats with varied CA/PU composition ratios, CA/PU 20/80 showed excellent tensile strength and Young's modulus. The residual product after selective removal of any one of the components in CA/PU composite nanofibres by washing with proper solvent maintained the fibre structure but greatly reduced the fibre size, suggesting CA/PU composite fibres showed a cocontinuous nanofibre structure due to phase separation in the spinning solution and in the course of electrospinning. 26 refs. Fujian,Normal University; Guangzhou,Institute of Chemistry CHINA
Accession no.1023728
Nakaya D; Chirachanchai S Polyoxymethylene (POM) nanofibres were produced by electrospinning from a hexafluoroisopropanol (HFIP)-based solvent. The nanofibres had significantly nanoporous surfaces. The presence of oxyethylene units in the polyoxymethylene copolymer decreased the surface roughness and porosity of the nanofibres, leading to a significant change in the specific surface area. A slight change in the molecular weight of the POM after electrospinning confirmed that the nanofibre with nanoporous POM shows hardly any degradation or decomposition during spinning. 30 refs. Chulalongkorn,University; Kyoto,University of Technology; Mitsubishi Gas Chemical Co.; Thai Polyacetal JAPAN; THAILAND
Accession no.1023676 Item 39 European Polymer Journal 44, No.7, 2008, p.1962. STUDY OF CHARGE STORAGE IN THE NANOFIBROUS POLY(ETHYLENE TEREPHTHALATE) ELECTRETS PREPARED BY ELECTROSPINNING OR BY CORONA DISCHARGE METHOD Ignatova M; Yovcheva T; Viraneva A; Mekishev G; Manolova N; Rashkov I In this paper, the charge storage performance of electrospun poly(ethylene terephthalate) (PET) mats with high specific surface area was evaluated in comparison to that of PET film electrets. Corona discharge method was used to charge the electrospun PET mats and PET films. The surface potential decay measurements revealed that the corona charged mats had higher initial values for the normalized surface potential compared to the electret films. A tendency for stabilisation of the electret charge to one and the same value for all charged samples (mats and films) after the 50th day was observed. The peaks at 90 deg.C in the thermally stimulated current (TSC) spectra of uncharged and charged in corona discharge electrospun PET mats were observed and attributed to a relaxation of the separated space charges, the dipole disorientation or injected charges within the bulk. It was found that the value of the storage charge in a corona charged electrospun PET mats was higher than that in PET mats prepared by electrospinning. 22 refs. Bulgaria,Academy of Sciences; Plovdiv,University BULGARIA; EASTERN EUROPE
Accession no.1023521 Item 38 Macromolecules 41, No.13, 8th July 2008, p.4746. ELECTROSPUN POLYOXYMETHYLENE: SPINNING CONDITIONS AND ITS CONSEQUENT NANOPOROUS NANOFIBER Kongkhlang T; Kotaki M; Kousaka Y; Umemura T;
© Copyright 2008 Smithers Rapra Technology
Item 40 Macromolecules 41, No.12, 24th June 2008, p.4275. ASSOCIATIVE POLYMER FACILITATED ELECTROSPINNING OF NANOFIBERS Talwar S; Hinestroza J; Pourdeyhimi B; Khan S A
43
References and Abstracts
Details are given of the preparation of hydrophobically modified associative polymers for use as an electrospinning aid for spinning polymer solutions that lack spinability at low concentrations. The model polymer used in this study was obtained from a methacrylic acid-ethyl acrylateethylene oxide copolymer. Various factors that can possibly influence the bead formation were investigated. 56 refs. North Carolina,State University; Cornell University USA
Accession no.1023190 Item 41 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.609, ISBN 978-0-8412-6276-7, ISSN 1550-6703, CD-ROM, 012. PDS/NANOHA BIOCOMPOSITE NANOFIBERS BY ELECTROSPINNING: STRUCTUREPROPERTY RELATIONSHIP Thomas V; Goli R; Zhang X; Vohra Y K Fibres were prepared by electrospinning of blends of poly(dioxanone) with gelatine and nano-hydroxyapatite (nano-HA) in 1,1,1,3,3,3-hexafluoro-2-propanol. The electrospun scaffolds had a very high porosity, surface area and well-interconnected pore structure, with a randomly oriented bead-free structure. The nano-HA-containing composites showed better tensile strengths and modulus than those omitting nano-HA, and the presence of gelatine and nano-HA improved cell affinity. 4 refs. Alabama,University at Birmingham (ACS,Div.of Polymeric Materials Science & Engng.)
Item 43 Polymer Reviews 48, No.2, April-June 2008, p.378. ELECTROSPINNING CELLULOSE AND CELLULOSE DERIVATIVES Frey M W A review is presented on the electrospinning of cellulose and cellulose derivatives, such as cellulose acetate, hydroxypropyl cellulose and ethyl cellulose, from various solvents, including N-methyl-morpholine N-oxide, water, lithium chloride, DMAc and ionic liquids. Various electrospun fibres are illustrated. 42 refs. Cornell University USA
Accession no.1022608 Item 44 Polymer Reviews 48, No.2, April-June 2008, p.353. CO-AXIAL ELECTROSPINNING FOR NANOFIBER STRUCTURES: PREPARATION AND APPLICATIONS Moghe A K; Gupta B S
USA
A brief introduction to conventional electrospinning is presented followed by a description of the basic set-up and process of coaxial electrospinning. The effects of and requirements for different materials and process parameters to achieve uniform core-sheath structures are discussed and the different types of co-axial structures produced (core-sheath bicomponent nanofibres, fibres from non-electrospinnable materials, hollow fibres, fibres containing encapsulated microparticles and periodic structures, are briefly reviewed. 48 refs.
Accession no.1022809
North Carolina,State University USA
Item 42 Textile Research Journal 78, No.6, June 2008, p.532. EFFECTS OF POLARITY ON ELECTROSPINNING PROCESS Kilic A; Demir A The effect of polarity on nanofibre production efficiency was investigated using PVAl/water solutions electrospun in two inversely polarised electrospinning configurations. One was a conventional electrospinning setup where the syringe is charged positively by the power supply and the collector is grounded and the other contains a collector polarised positively by the power supply and the collector syringe is grounded. The inverse setups were compared in terms of electrospinning efficiency and fibre morphologies, as determined by scanning electron microscopy. 13 refs. Istanbul,Technical University
Accession no.1022607 Item 45 Polymer Reviews 48, No.2, April-June 2008, p.317. A REVIEW: ELECTROSPINNING OF BIOPOLYMER NANOFIBERS AND THEIR APPLICATIONS Schiffman J D; Schauer C L A comprehensive review is presented on the electrospinning and end-use applications of biopolymers, which include polysaccharides, such as cellulose, chitin, chitosan and dextrose, proteins, such as collagen, gelatin and silk, and deoxyribonucleic acid as well as some biopolymer derivatives and composites. 282 refs. Drexel,University
TURKEY
USA
Accession no.1022700
Accession no.1022606
44
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 46 Journal of Polymer Science: Polymer Physics Edition46, No.12, 15th June 2008, p.1193. STUDY ON THE SHEAR VISCOSITY BEHAVIOR OF KERATIN/PEO BLENDS FOR NANOFIBRE ELECTROSPINNING Varesano A; Aluigi A; Vineis C; Tonin C Polyethylene oxide was added to an aqueous sulphonated keratin solution with the aim of enhancing electrospinnability and the rheological properties of the blend solutions investigated. Graessley's theory was employed to provide insight into the rheological properties of the blends in electrospinning and the shear rate dependent viscosity of the blends compared with that of pure polymer solutions. The characteristic time was calculated at the beginning of the non-Newtonian viscosity behaviour and the interaction between the sulphonated keratin and PEO in aqueous solutions investigated by applying additive rules to zeroshear viscosity. 32 refs. Biella,Istituto per lo Studio delle Macromolecole EUROPEAN COMMUNITY; EUROPEAN UNION; ITALY; WESTERN EUROPE
Accession no.1022568 Item 47 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2008. PMSE Preprints Volume 98. Preprints from a conference held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2008, p.147-148, ISBN 978-08412-6276-7, ISSN 1550-6703, CD-ROM, 012 ELECTROSPINNING SELF-STRATIFYING ADDITIVES WITH POLY(METHYL METHACRYLATE) The surface migration of hyperbranched terminally perfluorinated poly(ethylene imine) in electrospun blends with poly(methyl methacrylate) (PMMA) was examined by means of field-emission electron microscopy and x-ray photoelectron spectroscopy. The additive showed no significant effect on electrospinning of PMMA with regard to fibre morphology. However, the additives selectively migrated to the surfaces of the fibres during electrospinning to give enhanced fluorine-to-carbon ratios. Electrospun fibres could be selectively surface functionalised during electrospinning by incorporating functional groups in the additives. 13 refs. (ACS,Div.of Polymeric Materials Science & Engng.) Accession no.1022257 Item 48 Polymer 49, No.13-14, 2008, p.3125. MOLECULAR ORIENTATION IN INDIVIDUAL ELECTROSPUN NANOFIBERS MEASURED VIA POLARIZED RAMAN SPECTROSCOPY
© Copyright 2008 Smithers Rapra Technology
Bellan L M; Craighead H G Using polarised Raman spectroscopy, we have recorded Raman spectra from individual electrospun Nylon-6 nanofibres. Analysis of these single-fibre spectra, compared to those of unoriented and oriented Nylon-6 films, indicates significant molecular orientation. Because electrospinning produces fibres in a jet with a large strain rate, this molecular orientation is expected. We present quantitative measurements of molecular orientation in a single nanofibre and compare these to those of film samples. Such measurements could yield information about the uniformity of the electrospinning process and resulting fibres, and may also allow comparison between spectrally measured orientation functions and single-fibre mechanical properties. 33 refs. Cornell University USA
Accession no.1022145 Item 49 Materials Letters 62, No.20, 2008, p.3555. ELECTROSPUN CROSSLINKED POLYVINYL ALCOHOL MEMBRANE Enlong Yang; Xiaohong Qin; Shanyuan Wang The electrospinning of polyvinyl alcohol (PVA) was performed with maleic anhydride (MA) as a cross linker to fabricate slightly soluble nanofibre membrane. The solubility, morphology and thermal behaviour of electrospun PVA and PVA/MA membranes were characterized by water durability test, scanning electron microscope (SEM) and differential scanning calorimeter (DSC), respectively. Water durability test demonstrated that 8% PVA/MA (20/1, mole/mole) membrane had the least average mass loss and standard deviation. SEM images showed that fibres in PVA/MA membrane had a larger average diameter compared to those in PVA membrane. DSC investigated that crystal structure was formed in PVA/MA membrane. The results show that rapid evaporation of water and high electric field during electrospinning process may promote crosslinking of PVA and MA. 15 refs. Shanghai,Donghua University CHINA
Accession no.1022066 Item 50 Materials Letters 62, No.20, 2008, p.3493. QUANTITATIVE STUDY OF THE DISPERSION DEGREE IN CARBON NANOFIBER/POLYMER AND CARBON NANOTUBE/POLYMER NANOCOMPOSITES Luo Z P; Koo J H Quantitative measurements of the filler dispersion degree of carbon nanofibre (CNF) and nanotube (CNT) reinforced
45
References and Abstracts
polymer nanocomposites have been made by transmission electron microscopy. Samples were prepared by either high-shear mixing or twin-screw extrusion processing. It was found that the filler dispersion degree was largely influenced by the filler size. As the filler dimension became smaller, the dispersion parameter D0.1 largely decreased as quantified, which demonstrated the challenges associated with improving the dispersion of smaller fillers. This work provided a method to quantitatively compare the dispersion degrees of CNF/CNT polymer nanocomposites. 20 refs. Texas,A & M University; Texas,University at Austin USA
Accession no.1022065 Item 51 Polymer 49, No.12, 2008, p.2924. THEORY AND KINEMATIC MEASUREMENTS OF THE MECHANICS OF STABLE ELECTROSPUN POLYMER JETS Helgeson M E; Grammatikos K N; Deitzel J M; Wagner N J We present a simplified approach to understanding the mechanics of stable electrospinning jets based on electrohydrodynamic theory that explicitly incorporates the extensional rheology of polymeric fluids. Flow regimes of electrospun jets are identified by analogy to uniaxial extension of a fluid jet. These flow regimes predict the limiting kinematics of electrospinning jets and identify dimensionless parameters important to the control and operation of electrospinning processes. In situ kinematic measurements validate model assumptions and scaling predictions, and allow the reduction of entire jet radius and velocity profiles to several key parameters. The model predictions are shown to hold both above and below the entanglement concentration, as well as for solutions with added electrolyte and increased conductivity. The analysis also enables direct measurement of the apparent extensional viscosity of solutions at the high extension rates experienced during electrospinning. Finally, dimensional analysis of the model yields a correlation for electrospun fibre diameter in terms of measurable fluid properties, controlled process parameters, and measured jet variables, demonstrating the influence of mechanics in the straight portion of the jet on ultimate fibre morphology. 51 refs. Delaware,University USA
Accession no.1022017 Item 52 Polymer Preprints. Volume 49, Number 1, April 2008. Polymer Chemistry Division Preprints from the 235th National ACS Meeting, held New Orleans, La., 6th-10th April 2008. Washington, D.C., ACS,Div.of Polymer Chemistry, 2008, p.558, CD-ROM, 012 POLYANILINE NANOFIBER-BASED GAS
46
SENSORS Zhefei Li; Blum F D; Bertino M F; Chang-soo Kim Polyaniline was synthesised by in-situ chemical oxidation polymerisation of aniline using ammonium persulphate as the oxidant. Polyaniline nanofibres were prepared by exposing the precursor solution of distilled water, hydrochloric acid and ammonium persulphate to UV light for 30 min. SEM studies showed that fibres were laid down on the substrate as a sort of porous mesh. The high porosity and large surface area of the polyaniline produced indicated that this was potentially useful for gas detector applications. Changes In conductivity were monitored after the materials had been exposed to different gases. Polyaniline nanofibre thin films showed fast response times when exposed to chloroform vapour and the response was reversible. 4 refs. Missouri,University of Science and Technology; Virginia,Commonwealth University (ACS,Div.of Polymer Chemistry) USA
Accession no.1021784 Item 53 Macromolecules 41, No.11, 10th June 2008, p.3762. HIGH-ELONGATION FIBER MATS BY ELECTROSPINNING OF POLYOXYMETHYLENE Lu J-W; Zhang Z-P; Ren X-Z; Chen Y-Z; Yu J; Guo Z-X Details are given of the electrospinning of polyoxymethylene solutions in hexafluoropropanol. Tensile tests were stopped at various elongations to observe the change in fibre morphology during stretching. A very high elongation at break was observed with the polymer fibre mats. Morphologies were examined using SEM. 33 refs. Tsinghua,University CHINA
Accession no.1021706 Item 54 Polymer Preprints. Volume 49, Number 1, April 2008. Polymer Chemistry Division Preprints from the 235th National ACS Meeting, held New Orleans, La., 6th10th April 2008. Washington, D.C., ACS,Div.of Polymer Chemistry, 2008, p.894-895, CD-ROM, 012 TAILORD HYDROGEN-BONDING AND ELECTROSTATICS IN MELT ELECTROSPINNING FOR BIOMEDICAL DEVICES Hunley M T; McKee M G; Karikari A S; Mather B D; Long T E Melt electrospinning of star shaped poly(D,L-lactides) (PDLLA), synthesised as described elsewhere, and of a well-defined phospholipids (a low molar mass
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
amphiphile) were described. Fibres from each material were examined using scanning electron microscopy, and PDLLA and its fibres were further characterised using size exclusion chromatography, parallel plate rheometry and thermogravimetric analysis. Membranes were biodegradable and could be hydrogen bonded, using terminal hydrogen bonding units, to adenine or thymine. This hydrogen bonding in the molten state could be used to control fibre size during melt spinning. 15 refs.
Item 57 Chemistry of Materials 20, No.10, 27th May 2008, p.3420. ROOM TEMPERATURE IONIC LIQUID BASED POLYSTYRENE NANOFIBERS WITH SUPERHYDROPHOBICITY AND CONDUCTIVITY PRODUCED BY ELECTROSPINNING Lu X; Zhou J; Zhao Y; Qiu Y; Li J
Virginia,Polytechnic Institute & State University (ACS,Div.of Polymer Chemistry)
The fabrication of polystyrene (PS)-ionic liquid composite nanofibres as films by electrospinning from a solution of PS and various proportions of the ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate in dimethylformamide, and their characterisation by FESEM, FTIR, cyclic voltammetry, electrical conductivity and contact angle measurements, is described. The effects of processing conditions on the size, morphology, conductivity and hydrophobicity of the electrospun composites were investigated and the results are discussed in comparison with those for PS nanofibre films. 19 refs. Tsinghua,University; Dalian,Institute of Chemical Physics
USA
Accession no.1021643 Item 55 Journal of Applied Polymer Science 109, No.2, 15th July 2008 p.951. ELECTROSPUN NANOFIBERS FROM CROSSLINKED POLY(VINYL ALCOHOL) AND ITS FILTRATION EFFICIENCY Xiao-Hong Qin; Shan-Yuan Wang
CHINA
The electrospinning of crosslinked polyvinyl alcohol (PVAl) onto a polypropylene mesh sublayer, its characterisation by scanning electron microscopy, Fourier transform infrared spectroscopy and differential scanning calorimetry, and its use in filtration applications was described and discussed. Different area weights were laid down on the sublayer, and it was shown that filtration efficiency of the sublayer was significantly improved on the addition of the PVAl. 15 refs. Donghua,University
Accession no.1021402 Item 58 Iranian Polymer Journal 17, No.5, May 2008, p.373. EFFECT OF DIFFERENT COAGULATION BATHS AS COLLECTOR ON MORPHOLOGY OF GAS-JET/ELECTROSPUN POLY(ETHYLENE TEREPHTHALATE) NANOFIBRES Lin Y; Chi L; Yao Y; Wu D-C
CHINA
Accession no.1021450 Item 56 Journal of Applied Polymer Science 109, No.2, 15th July 2008 p.691. PREPARATION OF ALIGNED POLYETHERIMIDE FIBER BY ELECTROSPINNING SungCheal Moon; JaeKon Choi; Farris R J Solutions of 15 to 20 percent polyetherimide were prepared in methyl pyrrolidone, and were examined for their viscosity, electrical conductivity and surface tension. Electrospinning of the solutions was carried out and optimum spinning conditions determined and described. Structurally oriented and unidirectionally aligned nanofibres were obtained and these were characterised using field emission scanning electron microscopy. 14 refs. Massachusetts,University; Chosun,University SOUTH KOREA; USA
Accession no.1021417
© Copyright 2008 Smithers Rapra Technology
The fabrication of poly(ethylene terephthalate) nanofibres by gas-jet/electrospinning of solutions of the polymer in a mixture of phenol and 1,1,2,2-tetrachloroethane with collection of the fibres on a clean stainless steel plate or in three different coagulation baths using water, ethanol or a mixture of water and ethanol as coagulants is described. The morphology of the nanofibres was investigated using SEM and the effects of different coagulation baths are discussed in terms of average fibre diameter and the formation of beading on the fibre surface. 20 refs. Sichuan,University; Tianjin,Research Institute of Physical and Chemical Engineering of Nuclear Industry CHINA
Accession no.1021361 Item 59 Iranian Polymer Journal 17, No.5, May 2008, p.333. CYTO-COMPATIBILITY OF POLYETHERSULPHONE NANOFIBRES PREPARED BY GAS-JET/ELECTROSPINNING Wei N; Wang M; Lin Y; Gong P; Yao Y-Y; Li X-Y; Lin Y-H; Wu D-C; Man Y
47
References and Abstracts
The fabrication of nanofibre scaffolds of poly(ether sulphone) using a gas-jet/electrospinning technique from solutions of the polymer in dimethylformamide and the characterisation of their structural morphology by SEM, is described. The cytocompatibility of the nanofibre scaffolds was investigated by studies of the adhesion and proliferation of human umbilical vein endothelial cells and rat osteoblasts and cell-matrix interactions, and the results are discussed in terms of potential biomedical applications. 34 refs. Sichuan,University CHINA
Accession no.1021357 Item 60 Polymer Engineering and Science 48, No.6, 2008, p.1168. ELECTROSPINNING OF POLYAMIDES WITH DIFFERENT CHAIN COMPOSITIONS FOR FILTRATION APPLICATION Heikkilae P; Taipale A; Lehtimaeki M; Harlin A Electrospinning of several polyamides, PA6, PA66, PA612, PA614, PA1012, and PA1014, having different chain compositions and lengths of diacid and diamine segments, was demonstrated. Electrospinnability and fibre production rate of these polyamides were evaluated. Electrospun fibres were characterized with regard to their use in air filtration by measuring fibre diameter and filtration efficiency of fibre coating. Longer nonpolar chain segments of higher polyamides could in theory indicate higher dielectricity compared to PA6 and PA66, which would be an advantage in filtration applications. The solubility in polar formic acid and electrospinnability of higher polyamides, on the other hand, were clearly impaired with increased length of chain segments. Hence, PA66 is our best choice, and PA612 and PA6 our second options for commercial filtration applications if fibre electrospinnability, production rate, fibre diameter, and its distribution are concerned. Filtration efficiency of more than 95% of the particles having a diameter of 0.16 micro m and above was achieved with 0.5 g/m2 coating of PA66 nanofibres. Further increase in coating weight mainly increased the pressure drop to an unusable range without a significant further improvement of filtration efficiency. 49 refs. Tampere,University of Technology; VTT Technical Research Centre of Finland EUROPEAN UNION; FINLAND; SCANDINAVIA; WESTERN EUROPE
Accession no.1021334 Item 61 Macromolecular Rapid Communications 29, No.10, 19th May 2008, p.826. ENHANCED MECHANICAL PERFORMANCE OF SELF-BUNDLED ELECTROSPUN FIBER YARNS VIA POST-TREATMENTS Xuefen Wang; Kai Zhang; Meifang Zhu; Hsiao B S; Chu B
48
A new route to high-performance electrospun polymer fibres was developed using a self-bundling electrospinning technique combined with post-treatments such as stretching and annealing under conditions similar to those used for conventional fibres. Self-bundled electrospun PAN fibre yarns were characterised by SEM, mechanical tests, polarised FTIR spectroscopy and wide-angle X-ray diffraction. The obtained results revealed that the PAN nanofibre yarns possessed enhanced alignment, a higher degree of crystallinity and higher molecular orientation after treatments, resulting in a significant improvement in mechanical performance, approaching the strength value of the corresponding conventional fibres. 17 refs. Donghua,University; Stony Brook,University CHINA; USA
Accession no.1021099 Item 62 Macromolecular Rapid Communications 29, No.10, 19th May 2008, p.815. FABRICATION OF LIGHT-GUIDING CORE/SHEATH FIBERS BY COAXIAL ELECTROSPINNING Giseop Kwak; Ga Hyoung Lee; Shang-hun Shim; KeunByoung Yoon Light-guiding core/sheath fibres were fabricated from polymers of different refractive indices by coaxial electrospinning. Polymers studied were polycarbonate, PMMA and polyamide-66. The morphology and fibre diameter were analysed using SEM and fluorescence microscopy. It was found that the diameter of the core and the thickness of the sheath could be varied from 100 to 400 nm by changing the concentration of the outer solution. The incorporation of a chromophore into the inner material confirmed the uniformity of the core/sheath structure in long segments of the fibres. The boundary was clearly seen. The core diameter and the thickness of the sheath were constant along the fibre axis in fluorescence images. The ejected beam was circular and light-guided along the fibre axis as in an optical fibre. 25 refs. Kyungpook,National University KOREA
Accession no.1021097 Item 63 Macromolecular Chemistry and Physics 209, No.10, 22nd May 2008, p.1003. ELECTROSPUN ZEIN FIBRES USING GLUTARALDEHYDE AS THE CROSSLINKING REAGENT: EFFECT OF TIME AND TEMPERATURE Selling G W; Woods K K; Sessa D; Biswas A Zein was crosslinked with glutaraldehyde in acetic acid and fibres produced therefrom by electrospinning. The zein/ glutaraldehyde fibres were heated at temperatures from 80 to 180 degrees c for various times to provide fibres with
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
various degrees of insolubility. A model was developed relating the extent of dissolution with the amount of glutaraldehyde used and the temperature/time at which the fibres were exposed. The effect of glutaraldehyde derivatisation on the physical properties of the fibres was examined and the glutaraldehyde-modified fibres analysed by far-UV circular dichroism spectroscopy, SDS-PAGE, IR spectroscopy, NMR spectroscopy and polarised light microscopy. 28 refs. USDA; US,Agricultural Research Service USA
Accession no.1020849 Item 64 Chemistry of Materials 20, No.9, 13th May 2008, p.3085. NANOSTRUCTURED PURE ANATASE TITANIA TUBES REPLICATED FROM ELECTROSPUN POLYMER FIBER TEMPLATES BY ATOMIC LAYER DEPOSITION Kim G-M; Lee S-M; Michler G H; Roggendorf H; Goesele U; Knez M The fabrication of pure anatase titanium dioxide submicrotubes by a template-directed method using electrospun polyvinyl pyrrolidone fibres as the template for coating with titanium dioxide by an atomic layer deposition technique is reported. Deposition is carried out at 70 degrees C using titanium tetraisopropyl oxide and pure water as precursors of titanium dioxide and the crystal structure, microstructure and optical properties of the titanium dioxide deposited layers characterised before and after calcination. 30 refs. Martin-Luther-Universitat Halle EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1020819 Item 65 Chemistry of Materials 20, No.9, 13th May 2008, p.3055. FABRICATION OF CONTINUOUS CONDUCTING GOLD WIRES BY ELECTROSPINNING Pol V G; Koren E; Zaban A An innovative approach for electrospinning of gold polymer wires, which entails dissolving HAuCl4 salt in ethanol followed by the addition of polyacrylic acid, is described. The as-prepared gold polymer wires are assembled on a rotating drum in between the spinneret (+ electrode) and conducting substrate (- electrode) and are transformed to gold wires via sintering. The gold polymer wires and gold wires are characterised by elemental analysis, X-ray diffraction, DSC, scanning electron microscopy, energy dispersive X-ray analysis, TEM and digital camera photography and the conducting nature of single gold nanowires is confirmed by electrical conductivity and cyclic voltammetry measurements. 26 refs.
© Copyright 2008 Smithers Rapra Technology
Bar-Ilan,University ISRAEL
Accession no.1020817 Item 66 Journal of Applied Polymer Science 109, No.1, 15th July 2008, p.406. PREPARATION OF POLYURETHANE NANOFIBERS BY ELECTROSPINNING Zhou H; Hu J; Chen S; Yeung L PU fibres were prepared by electrospinning. Process parameters including applied voltage, feeding rate, and solution concentration were investigated. The influence of processing parameters on the diameter and morphology of the nanofibres was examined. Characterisation was carried out using SEM and DSC. 31 refs. Hong Kong,Polytechnic University CHINA
Accession no.1020774 Item 67 Journal of Biomaterials Science: Polymer Edition 19, No.5, 2008, p.677. ELECTROSPUN CHITOSAN-P(LLACL) NANOFIBERS FOR BIOMIMETIC EXTRACELLULAR MATRIX Chen F; Li X; Mo X; He C; Wang H; Ikada Y The fabrication of blend nanofibres of chitosan and various proportions of poly(L-lactic acid-co-epsilon caprolactone) as a biomimetic extracellular matrix by electrospinning from solutions in a mixture of hexafluoroisopropanol and trifluoroacetic acid, and their characterisation by SEM, tensile testing, density, XRD and FTIR, is described. The effects of blend composition on porosity, mechanical properties and fibroblast cell growth on the nanofibres were investigated and the results are discussed in terms of potential tissue engineering and drug delivery system applications. 31 refs. Shanghai,Donghua University; Nara,Medical University CHINA; JAPAN
Accession no.1020695 Item 68 Journal of Biomaterials Science: Polymer Edition 19, No.5, 2008, p.635. HYBRID NANOFIBROUS SCAFFOLDS FROM ELECTROSPINNING OF A SYNTHETIC BIODEGRADABLE ELASTOMER AND URINARY BLADDER MATRIX Stankus J J; Freytes D O; Badylak S F; Wagner W R The fabrication of a hybrid electrospun scaffold composed of a biodegradable poly(ester-urethane)urea (PEUU), derived from poly(caprolactone diol) and 1,4-diisocyanatobutane with chain extension by 1,4diaminobutane, and various proportions of a porcine
49
References and Abstracts
extracellular matrix scaffold (urinary bladder matrix), and its characterisation by SEM, DSC, uniaxial tensile testing, in-vitro weight loss in phosphate buffer saline, cytocompatibility and subcutaneous implantation, is described. The effects of PEUU content on mechanical properties, cell adhesion, cell proliferation and weight loss are discussed in terms of soft tissue engineering applications. 33 refs. Pittsburgh,University USA
Accession no.1020694 Item 69 Journal of Biomaterials Science: Polymer Edition 19, No.5, 2008, p.623. CHARACTERIZATION OF NEURAL STEM CELLS ON ELECTROSPUN POLY(EPSILONCAPROLACTONE) SUBMICRON SCAFFOLDS: EVALUATING THEIR POTENTIAL IN NEURAL TISSUE ENGINEERING Nisbet D R; Yu L M Y; Zahir T; Forsythe J S; Shoichet MS The fabrication of three-dimensional non-woven poly(epsilon-caprolactone) scaffolds by electrospinning and their subsequent chemical modification by treatment with ethylenediamine (ED), was investigated by SEM, contact angle measurements, XPS and fluorescence. The characterisation of rat brain-derived neural stem cells (NSCs) on the polymeric scaffolds was studied and the effects of treatment with ED on proliferation and differentiation of the NSCs are discussed in terms of the physical and chemical properties of the scaffolds. 28 refs. Monash,University; Toronto,University
AIST JAPAN
Accession no.1020482 Item 71 Polymer 49, No.11, 2008, p.2755. CONTINUOUS POLYMER NANOFIBER YARNS PREPARED BY SELF-BUNDLING ELECTROSPINNING METHOD Wang X; Zhang K; Zhu M; Yu H; Zhou Z; Chen Y; Hsiao B S Continuous polymer nanofibre yarns were manufactured by self-bundling electrospinning method. Compared with typical electrospinning setup, the special difference in this method was that a grounded needle tip was used to induce the self-bundling of polymer nanofibres at the beginning of electrospinning process. Four kinds of polymer self-bundling yarns, poly(3hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), polyacrylonitrile (PAN), poly(l-lactic acid) (PLLA) and poly(m-phenylene isophthalamide) (PMIA), were prepared successfully by using this self-bundling electrospinning method. Good alignment of polymer nanofibres in self-bundled yarns was confirmed by SEM observation. It was found out that the conductivity of the polymer solution was crucial to achieve stably continuous self-bundled fibre yarns. A possible mechanism for the self-bundling formation of align nanofibre yarn was proposed. 35 refs. Shanghai,Donghua University; Stony Brook,University CHINA; USA
Accession no.1020454
AUSTRALIA; CANADA
Accession no.1020693 Item 70 Materials Letters 62, No.19, 2008, p.3370. A NEW ELECTROSPINNING METHOD TO CONTROL THE NUMBER AND A DIAMETER OF UNIAXIALLY ALIGNED POLYMER FIBERS Ishii Y; Sakai H; Murata H A novel electrospinning process of uniaxially aligned submicron fibres was developed. The number of the fibres was precisely controlled by changing biased collector, and the diameter of the fibre was varied by post-deposition stretching process. This method realized the formation of number-controlled aligned poly[2methoxy-5-(2'-ethyl-hexyloxy)-1,4-phenylenevinylene] (MEH-PPV)/poly(ethylene oxide) (PEO) fibres with the systematic control of the diameter ranging from micrometer to submicrometer. Significant improvement of the uniformity of the fibre diameter was also observed by the stretching process. 15 refs.
50
Item 72 Textile Research Journal 78, No.3, March 2008, p.254. PREPARATION OF POLYETHYLENE OXIDE/CHITOSAN FIBER MEMBRANES BY ELECTROSPINNING AND THE EVALUATION OF BIOCOMPATIBILITY Ching-Wen Lou; Jia-Horng Lin; Ko-Chung Yen; Chao-Tsang Lu; Chia-Yi Lee Polyethylene oxide/chitosan nanofibres were prepared by electrospinning of solutions of PEO and chitosan in an electric field using various solvents, volume ratios of PEO and chitosan and differing electric fields. The attachment and migration of osteosarcoma cells on the electrospun fibres were investigated and the morphology of the cells cultured on the surface of the nanofibrous membranes studied by scanning electron microscopy. Taiwan,Central University of Science and Technology; Feng Chia,University TAIWAN
Accession no.1020267
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 73 Journal of Functional Polymers 21, No.1, March 2008, p.20. CHINESE NANOFIBROUS MATS OF RIGID POLYSACCHARIDES PREPARED BY COAXIAL ELECTROSPINNING Yi-Jie Liu; Yan Li; Hong-Liang Jiang; Ying-Qian Hu; Kang-Jie Zhu Nanofibrous membranes of rigid polysaccharides including chitosan, alginate or hyaluronic acid were prepared by coaxial electrospinning of their corresponding aqueous solutions and PEO solution in a DMF/water admixture followed by removal of the outer PEO shell by extraction of the core-shell fibres with chloroform. The fibre structure was characterised by TEM and scanning electron microscopy. The fibres displayed integrated structures after PEO treatment. 17 refs. China,Ministry of Education; Zhejiang,University CHINA
Accession no.1020198 Item 74 Macromolecular Research 16, No.3, April 2008, p.212. A STUDY OF ELECTROSPUN PVDF ON PET SHEET Chanunpanich N; Byungsoo Lee; Hongsik Byun Polyvinylidene fluoride (Kynar 761) nanofibres were prepared by electrospinning under various conditions and the effects of processing parameters, such as voltage, travelling distance, flow rate and polymer concentration, on the morphology and diameter distribution of the nanofibres investigated by scanning electron microscopy and optical microscopy. Optimum conditions for electrospinning in a DMAc/ acetone solution were established and the nanofibres electrospun onto a PETP sheet using a rotating drum as an electrically grounded collector. Both straight and aligned nanofibres were obtained through manipulation of the collector. 33 refs. King Mongkut's Institute of Technology North Bangkok; Keimyung,University KOREA
Accession no.1020018 Item 75 Macromolecular Research 16, No.3, April 2008, p.204. PLATINUM-CATALYZED AND ION-SELECTIVE POLYSTYRENE FIBROUS MEMBRANE BY ELECTROSPINNING AND IN-SITU METALLIZATION TECHNIQUES Seung-Hee Hong; Sun-Ae Lee; Jae-Do Nam; YoungKwan Lee; Tae-Sung Kim; Sungho Won
© Copyright 2008 Smithers Rapra Technology
A platinum-catalysed polyelectrolyte porous membrane was prepared by electrospinning of PS and solid-state compression moulding of the electrospun PS fibres. The PS fibres were sulphonated with chlorosulphonic acid and the surface of the sulphonated PS fibres metallised with platinum in-situ. The compressed PS fibre membrane possessed cation-selective polyelectrolyte characteristics with ionic conductivities of up to 0.32 S/cm, indicating the potential use of the polyelectrolyte system in methanol fuel cell applications. 47 refs. Sung Kyun Kwan University KOREA
Accession no.1020017 Item 76 Macromolecules 41, No.9, 13th May, 2008, p.3144. CRYSTALLIZATION BEHAVIOR OF ELECTROSPUN PB/PMP BLEND FIBROUS MEMBRANES Lee K H; Givens S R; Snively C M; Chase B; Rabolt J F Fibrous polyolefin membranes were prepared by electrospinning from multicomponent solvent systems. Fibres spun from a polybutylene/poly(4-methylpent1-ene) (PB/PMP) blend had a twisted-ribbon structure with irregular twisting points along the length of the fibres. The crystallisation of PB was markedly affected by the addition of PMP to the blend. A mixture of forms I and II was present in pure PB fibrous membranes, and the thermodynamically metastable form II gradually transformed into form I with ageing at room temperature. However, this transformation did not occur in the PB/ PMP blends because of stabilisation of PB form II in the blend. Pure PMP fibres and fibres made from the PB/PMP blend both contained PMP in crystal form I, showing that the crystallisation behaviour of PMP was unaffected by blending with PB. 30 refs. Delaware,University; Dupont USA
Accession no.1019860 Item 77 Macromolecular Symposia No.264, 2008, p.80. ULTRAFINE ELECTROSPUN CONDUCTING POLYMER BLEND FIBERS AND THEIR PHOTOLUMINESCENCE PROPERTIES Chuangchote S; Sagawa T; Yoshikawa S Ultrafine poly(2-methoxy-5-(2'-ethylhexyloxy)-1,4phenylene-vinylene)(MEH-PPV)/polyvinyl pyrrolidone blend fibres with average diameters ranging from 625 nm to 1.46 micrometers were prepared by electrospinning of blend solutions using a mixed solvent of chlorobenzene and methanol. The effects of applied electrical potential, collection distance and MEH-PPV composition on fibre diameter were examined. The UV vis absorption and
51
References and Abstracts
fluorescence characteristics of the electrospun fibres with various blend compositions and electrospun fibres with polyvinyl pyrrolidone removed therefrom by Soxhlet extraction were also investigated and compared. 23 refs. (2nd International Conference on Advances in Petrochemicals and Polymers, (ICAPP 2007), Bangkok, Thailand, 25th-28th June) Kyoto,University JAPAN
Accession no.1019623 Item 78 Journal of Polymer Engineering 28, No.1-2, 2008, p.119. APPLICATION OF SIROFIL TECHNOLOGY TO ELECTROSPINNING Ji-Huan He The use of nano-sirospinning using bubble-electrospinning to produce microcomposite yarns from thousands of nanofibres is proposed. The cyclone mechanism is utilised to create a novel cyclone spinning process. 16 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Donghua,University; China,Ministry of Education CHINA
Accession no.1019561 Item 79 Journal of Polymer Engineering 28, No.1-2, 2008, p.115. PAN/PVP MICRO COMPOSITE FIBERS USING ELECTROSPINNING Da-Hua Shou; Ji-Huan He A simple and facile one-step method for the preparation of microcomposite fibres from mixtures of PAN and polyvinyl pyrrolidone by electrospinning is described. The microcomposite fibres are characterised by optical microscopy and considered potential candidates for tissue engineering, wound dressings, drug release and sound absorption. 7 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Donghua,University; China,Ministry of Education CHINA
Accession no.1019560 Item 80 Journal of Polymer Engineering 28, No.1-2, 2008, p.67. THE EFFECTS OF FLOW RATE AND THE DISTANCE BETWEEN THE NOZZLE AND THE TARGET ON THE OPERATING CONDITIONS OF ELECTROSPINNING Ying Yang; Zhidong Jia; Jianan Liu; Liming Wang; Zhicheng Guan
52
A systematic investigation was carried out into the effects of flow rate and the distance between the nozzle and target on the operating conditions during the electrospinning of an aqueous solution of polyethylene oxide. The electric field strength at the nozzle was calculated to establish steady operating conditions and high speed images were used to capture the jet path during electrospinning. The results obtained revealed that limited fibre diameter did not occur at the lowest flow rate but was affected by the electric force per unit mass and evaporation. The electric field required to maintain steady spinning at a short distance was markedly influenced by evaporation and was significantly affected by the flow rate at a large distance between the nozzle and target. 30 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Tsinghua,University; shenzhen,Graduate School CHINA
Accession no.1019557 Item 81 Journal of Polymer Engineering 28, No.1-2, 2008, p.55. THE PRINCIPLE OF BUBBLE ELECTROSPINNING AND ITS EXPERIMENTAL VERIFICATION Yong Liu; Ji-Huan He; Lan Xu; Jian-Yong Yu Nanofibres were produced from an aerated PAN solution by bubble electrospinning and their morphological properties investigated by scanning electron microscopy. The principles of bubble electrospinning were analysed with the aid of a high-speed camera and the transient motion of jets ejected from the bubbles captured. Small bubbles were formed on the surface with small surface tension. 35 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Donghua,University; China,Ministry of Education CHINA
Accession no.1019556 Item 82 Journal of Polymer Engineering 28, No.1-2, 2008, p.43. ELECTROSPUN OIL SORPTIVE FIBER BASED ON EPDM Yan-Ping Liu; Mei-Hua Zhou Ultrafine EPDM fibres were prepared by electrospinning of EPDM in a solution of THF and cyclohexane and crosslinked by microwave radiation. The structure of the fibres before and after crosslinking was characterised by FTIR spectroscopy and the morphology of the fibres investigated by scanning electron microscopy. The swelling behaviour of the fibres in kerosene, toluene and chloroform was evaluated and kinetics of swelling determined. The fibres produced possessed diameters ranging from 400 nm to 1.8 micrometers, formed non-woven mats with abundant capillary channels and exhibited rapid swelling
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
behaviour and improved oil absorption ability. 10 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Donghua,University CHINA
Accession no.1019555 Item 83 Journal of Polymer Engineering 28, No.1-2, 2008, p.33. CHARACTERIZATION OF ODPA-ODA POLYIMIDE NON-WOVEN MEMBRANES PREPARED BY ELECTROSPINNING Hong-Wei Duan; Yan Wang; Yu-Jun Zhang; Lin Geng Non-woven polyimide membranes were prepared by electrospinning a solution of a polyamic acid obtained from 4,4'-oxydiphthalic anhydride and 4,4'-oxydianiline at room temperature for about 4 h followed by thermal imidisation. The surface morphology and crystallinity of the polyimide precursor and polyimide membranes were characterised by scanning electron microscopy and X-ray diffraction, respectively, and the mechanical properties of the membranes determined by tensile testing. The diameter of fibres produced by imidisation at 300 degrees C decreased by 500 nm and possessed a shrunken, twisted and ribbon-shaped structure. The membranes were considered suitable for insulation. 10 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Harbin,Northeast Forestry University; Harbin,University of Science & Technology; Harbin,Institute of Technology CHINA
Accession no.1019554 Item 84 Journal of Polymer Engineering 28, No.1-2, 2008, p.27. DRUG-LOADED PBS MICRO SPHERES WITH CHINESE DRUG BY ELECTROSPINNING LAN Xu; Zhongfu Ren Drug-loaded polybutylene succinate microspheres for wound treatment were prepared by electrospinning using, as the drug, Yunnan Baiyo, and characterised by scanning electron microscopy. The diameter and number of the microspheres were controlled by tuning of the voltage during electrospinning. 18 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October)
ALLOMETRIC SCALING LAW BETWEEN AVERAGE POLYMER MOLECULAR WEIGHT AND ELECTROSPUN NANOFIBER DIAMETERZhongfu Ren; Baozhi Liu; Zhuyan Shao; Ji-Huan He The development of a mathematical model for describing polymer solution viscosity is reported. An allometric scaling law between average molec.wt. and solution viscosity is obtained and the scaling relationship between electrospun fibre diameter and average molec. wt. derived using He Chengtian's interpolation. 26 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Jining,Medical College; Donghua,University CHINA
Accession no.1019552 Item 86 Journal of Polymer Engineering 28, No.1-2, 2008, p.5. FABRICATION, MORPHOLOGY, AND STRUCTURE OF ELECTROSPUN PAN-BASED CARBON NANOFIBERS Saiyasombat C; Maensiri S Carbon nanofibres were prepared by electrospinning a PAN precursor/DMF solution and carbonisation of the resulting nanofibres in either argon or nitrogen at 1000 degrees centigrade. The effects of PAN concentration and applied voltage on the morphology of the nanofibres and nanofibre diameter were investigated and optimal parameters for producing nanofibres with narrow particle size distributions and without bead formation along the fibres established. The effect of carbonisation on the structure and purity of the carbon nanofibres was investigated and temperatures of possible decomposition and crystallisation of the nanofibres determined by TGA-DTA. Nanofibre morphology was characterised by scanning electron microscopy. 29 refs. (2007 International Symposium on Nonlinear Dynamics, Shanghai, China, October) Khon Kaen,University THAILAND
Accession no.1019551
Donghua,University; Jining,Medical CollegeCHINA Accession no.1019553
Item 87 Journal of Polymer Engineering 28, No.1-2, 2008, p.1. ELECTROSPINNING: A PROMISING TECHNOLOGY FOR DISCONTINUOUS AND CONTINUOUS NANOFIBERS Ji-Huan He
Item 85 Journal of Polymer Engineering 28, No.1-2, 2008, p.19.
A brief discussion is presented on the electrospinning of nanofibres, focusing upon mimicking of the spiderspinning process in electrospinning and theoretical aspects of electrospinning. (2007 International
© Copyright 2008 Smithers Rapra Technology
53
References and Abstracts
Symposium on Nonlinear Dynamics, Shanghai, China, October) 16 refs. Donghua,University CHINA
Accession no.1019550 Item 88 Journal of Materials Science. Materials in Medicine 19, No.2, Feb.2008, p.827. ENCAPSULATION AND CONTROLLED RELEASE OF LYSOZYME FROM ELECTROSPUN POLY(EPSILONCAPROLACTONE)/POLY(ETHYLENE GLYCOL) NON-WOVEN MEMBRANES BY FORMATION OF LYSOZYME-OLEATE COMPLEXES Yan Li; Hongliang Jiang; Kangjie Zhu Lysozyme was incorporated into electrospun polyepsilon-caprolactone/polyethylene glycol non-woven membranes using the concept of hydrophobic ion pairing. The solubility of lysozyme in an organic solvent was enhanced through the formation of lysozyme-sodium oleate complexes which were directly loaded into the membranes through the electrospinning process. The electrospun non-woven membranes were investigated by scanning electron microscopy, contact angle measurements and DSC and the release behaviour of lysozyme from the membranes examined. The biological activity of lysozyme released from the membranes was also investigated and compared with that of the native one. 23 refs. Zhejiang,University CHINA
Accession no.1019464 Item 89 Polymer Preprints. Volume 49, Number 1, April 2008. Polymer Chemistry Division Preprints from the 235th National ACS Meeting, held New Orleans, La., 6th10th April 2008. Washington, D.C., ACS,Div.of Polymer Chemistry, 2008, p.365-366, CD-ROM, 012 PREPARATION OF CONDUCTIVE POLYMER NANOFIBERS VIA ELECTROSPINNING OF POLYARYLSILYLENE PRECURSORS Choi J; Ner Y; Sotzing G A Details are given of the formation of polybithiophene nanofibres via spinning of solution-processable polybithienylsilylene precursors. Electrochemical and chemical solid-state oxidative conversion were performed. Characterisation was carried out using SEM and cyclic voltammetry. 7 refs. Connecticut,University (ACS,Div.of Polymer Chemistry) USA
Accession no.1019432
54
Item 90 Polymer Preprints. Volume 49, Number 1, April 2008. Polymer Chemistry Division Preprints from the 235th National ACS Meeting, held New Orleans, La., 6th10th April 2008. Washington, D.C., ACS,Div.of Polymer Chemistry, 2008, p.454-455, CD-ROM, 012 CROSSLINKABLE POLYELECTROLYTES FOR POROUS, ELECTROSPUN ANTIMICROBIAL SCAFFOLDS Hunley M T; Layman J M; Long T E Photocrosslinkable polydimethylaminoethyl methacrylate with cinnamate groups was synthesised through the alkylation of the tertiary amine. Polydimethylaminoethyl methacrylate with cinnamate was electrospun and crosslinked to generate insoluble fibres. Characterisation was undertaken using SEM and proton NMR. 13 refs. Virginia,Polytechnic Institute (ACS,Div.of Polymer Chemistry) USA
Accession no.1019375 Item 91 Polymer Preprints. Volume 49, Number 1, April 2008. Polymer Chemistry Division Preprints from the 235th National ACS Meeting, held New Orleans, La., 6th10th April 2008. Washington, D.C., ACS,Div.of Polymer Chemistry, 2008, p.410-411, CD-ROM, 012 ANTIMICROBIAL NANOSCALE FIBERS FROM ELECTROSPINNING ZWITTERIONIC COPOLYMERS Huyck R H; Hunley M T; Allen M H; Long T E Details are given of the synthesis of a series of lowTg copolymers with zwitterions content through incorporation of either a sulphobetaine methacrylate of sulphobetaine methacrylamide monomer. The effects of zwitterions content and structure on electrospun fibre diameter and morphology were explored. Characterisation was carried out using proton NMR, SEM and steady shear experiments. 9 refs. Virginia Tech (ACS,Div.of Polymer Chemistry) USA
Accession no.1019355 Item 92 Polymer Engineering and Science 48, No.5, 2008, p.934. EFFECT OF HOT-PRESS ON ELECTROSPUN POLY(VINYLIDENE FLUORIDE) MEMBRANESNa H; Zhao Y; Zhao C; Zhao C; Yuan X Poly(vinylidene fluoride) (PVDF) was electrospun into ultrafine fibrous membranes from its solutions in a mixture of N,N-dimethylformamide and acetone (9:1, v/v). The
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
electrospun membranes were subsequently treated by continuous hot-press at elevated temperatures up to 155 degree C. Changes of morphology, crystallinity, porosity, liquid absorption, and mechanical properties of the membranes after hot-press were investigated. Results of scanning electron microscopy showed that there were no significant changes in fibrous membrane morphology when the hot-press temperature varied from room temperature to 130 degree C, but larger pores were formed because of fibres melting and bonding under higher temperatures. Analyses of X-ray diffraction and differential scanning calorimeter exhibited that the crystalline form of PVDF could transfer from beta-type to alpha-type during hot-press at temperatures higher than 65 degree C. Tensile tests suggested that the mechanical properties of the electrospun PVDF membranes were remarkably enhanced from 25 to 130 degree C, whereas the porosity and the liquid absorption decreased. The hotpress at 130 degree C was optimal for the electrospun PVDF membranes. The continuous hot-press post-treatment could be a feasible method to produce electrospun membranes, not limited to PVDF, with suitable mechanical properties as well as good porosity and liquid absorption for their applications in high-quality filtrations or battery separators. 21 refs. Tianjin,University; Beijing,University of Technology & Business CHINA
Accession no.1019171 Item 93 Polymer Composites 29, No.5, 2008, p.579. COAXIAL ELECTROSPINNING OF PC(SHELL)/ PU(CORE) COMPOSITE NANOFIBERS FOR TEXTILE APPLICATION Han X; Huang Z; He C; Liu L; Wu Q To develop a novel functional composite material for textile application, a coaxial electrospinning technique was investigated to electrospin two different polymer solutions into core-shell structured nanofibres in which polyurethane and polycarbonate were used as core and shell materials, respectively. The resultant nanofibres were subsequently characterized by means of scanning electron microscope, transmission electron microscopy, fourier transform infrared spectroscopy, and tensile mechanical test. Furthermore, water vapour transmission rate and pliability of the resulting nonwoven mats were also measured. The preliminary results indicated that it is feasible to attach composite nanofibres, with possible fictionalization on the shell material, onto a substrate fabric. 20 refs.
CORE-SHEATH FUNCTIONAL POLYMER NANOFIBERS PREPARED BY COELECTROSPINNING Yi Xin; Zonghao Huang; Wenwen Li; Zijiang Jiang; Yanbin Tong; Cheng Wang Core-sheath polymer nanofibres with optoelectronic materials as the sheath and easily spinnable polymer as the core were prepared by co-electrospinning. Three prototypical systems of polystyrene/poly(p-phenylene vinylene) (PS/PPV), poly(vinyl alcohol)/poly(p-phenylene vinylene) (PVA/PPV) and polystyrene/tris(8-quinolinolato) aluminium ( PS/Alq3) were investigated. The fluorescence microscopy images showed that the resulting nanofibres with uniform morphologies exhibited outstanding emission properties. The core-sheath structures of these nanofibres were observed by TEM investigation. The photoluminescence spectra indicated that the fluorescent properties of these functional core-sheath nanofibres could be influenced by the interaction between core and sheath materials. 30 refs. China,Northeast Normal University CHINA
Accession no.1018814 Item 95 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago,Il., 25th29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.276-277, ISBN 978-0-8412-7436-5, CD-ROM, 012 ELECTROSPINNING OF CERAMIC NANOFIBERS Elick B M; Youngblood J P A novel approach for preparing ceramic fibres at a much smaller scale than is currently available by commercial processes was described. Preceramics were co-spun with PS because of its ability to be crosslinked by UV light. In this novel approach, the UV cure step kept the fibres from flowing during the pyrolysis step. The fibres appeared to be continuous and without pores. Field emission SEM and TEM techniques of the fully ceramic fibres showed that the average fibre diameter was about 50 nm. The fibres were crystalline. 5 refs. Purdue,University (ACS,Div.of Polymeric Materials Science & Engng.) USA
Accession no.1018576
Tongji,University CHINA
Accession no.1019134 Item 94 European Polymer Journal 44, No.4, 2008, p.1040.
© Copyright 2008 Smithers Rapra Technology
Item 96 Journal of Materials Science 43, No.5, March 2008, p.1664. YBCO NANOFIBERS SYNTHESIZED BY ELECTROSPINNING A SOLUTION OF POLY(ACRYLIC ACID) AND METAL NITRATES
55
References and Abstracts
Greenberg Y; Lumelsky Y; Silverstein M S; Zussman E A versatile approach to the synthesis of YBCO (high temperature superconductor ceramics) nanofibres via electrospinning of a polymer precursor solution was developed. The aqueous polymer precursor solution consisted of polyacrylic acid and a mixture of yttrium nitrate, barium nitrate and copper nitrate. The conductivity of the polymer precursor solution at 27.1 deg C was 14.70 mS/cm, its zero shear viscosity was 52.00 cP, and its pH was 1.88. Typical YBCO nanofibres were 50-100 nm in diameter and around 10 micrometres in length. The nanofibres also contained relatively small amounts of yttrium oxide and copper yttrium oxide. 29 refs. Technion-Israel Institute of Technology ISRAEL
Accession no.1017876
spectroscopy and thermogravimetry. The results obtained indicated that a condensation reaction occurred between the hydroxyl groups of the PDMS and TEOS. The hybrid fibres possessed excellent high temperature stability and fibre diameters which increased with increasing PDMS content. 7 refs. Hefei,University of Technology CHINA
Accession no.1017580 Item 99 Macromolecular Chemistry and Physics 209, No.5, 5th March 2008, p.508. GLYCIDYL-METHACRYLATE-BASED ELECTROSPUN MATS AND CATALYTIC SILVER NANOPARTICLES Semir M M; Ugur G; Gulgun M A; Menceloglu Y Z
Item 97 Journal of Biomaterials Science: Polymer Edition 19, No.3, 2008, p.373. ANTIBACTERIAL AND ANTIMYCOTIC ACTIVITY OF A CROSS-LIKED ELECTROSPUN POLY(VINYL PYRROLIDONE)-IODINE COMPLEX AND A POLY(ETHYLENE OXIDE)/ POLY(VINYL PYRROLIDONE)-IODINE COMPLEX Ignatova M; Markova N; Manolova N; Rashkov I
The fabrication of poly(acrylonitrile-co-glycidyl methacrylate) and poly(glycidyl methacrylate) fibre mats coated with monodisperse silver nanoparticles by a combination of electrospinning and electroless plating via surface hydrazination and redox reaction of the hydrazine groups with silver nitrate is described. The products were characterised by FTIR, TGA, TEM and SEM, and the catalytic activity of the silver nanoparticles was investigated using a model redox reaction between methylene blue and sodium borohydride. 37 refs.
The preparation of photocrosslinked polyvinyl pyrrolidone and PEO/polyvinyl pyrrolidone electrospun nanofibrous mats containing complex-bound iodine is described and the characterisation of the mats and complexes by means of scanning electron microscopy, X-ray mapping and FTIR spectroscopy is reported. Also reported are the antibacterial and antimycotic activities of the iodine complex-containing mats and scanning electron microscopy observations of the mats inhibiting adhesion of bacteria Staphylococcus aureus. The mats are considered promising for various biomedical applications, including wound dressings. 37 refs. Bulgarian Academy of Sciences; Sofia,Institute of Polymers; Sofia,Institute of Microbiology
Izmir,Institute of Technology; Sabanci,University
BULGARIA; EASTERN EUROPE
Accession no.1017668 Item 98 Polymer Materials Science and Engineering 24, No.1, Jan.2008, p.47. PREPARATION AND CHARACTERIZATION OF PDMS/SIO2 HYBRID ELECTROSPINNING FIBERS Hua-Zhong Yang; Tie-Jun Shi; Lin-Feng Zhai Polydimethyl siloxane/silica hybrid fibres were prepared by sol-gel technology and electrospinning and their morphologies and thermal properties investigated by field emission scanning electron microscopy, FTIR
56
TURKEY
Accession no.1017145 Item 100 Materials World 16, No.4, April 2008, p.26. BOTTOM-UP MATERIALS FROM DOWN UNDER Tucker N Electrospinz of Blenheim, New Zealand, has started to make laboratory scale electrospinning machines for research organisations to make ultrafine and nanoscale fibres. The data used in the machine design comes from a Crown Research Institute, the New Zealand Institute for Crop and Food Research. Crop and Food Research scientists are testing the potential of electrospun proteins and polysaccharides as industrial raw materials. They are interested in how the materials perform as filters or structural elements. There are a number of national initiatives under way to exploit crop origin industrial materials. Aside from limited production of polylactic acid and the import of significant quantities of CargillDow NatureWorks, the main producer of biopolymer materials in New Zealand is Blenheim-based Potatopak. The company has developed a viable production route for food packaging trays made from potato starch. The starch is sourced from potato processing waste.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
New Zealand,Crop and Food Research Centre NEW ZEALAND
Accession no.1017023 Item 101 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago,Il., 25th-29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.102, ISBN 978-0-8412-7436-5, CD-ROM, 012 CHARACTERIZING ELECTROSPUN FIBERS OF POLY(ETHER) IMIDE SOLUTIONS BY RELATION TO THEIR DIELECTRIC PROPERTIES Mills K C; Franzek E; Hinestroza J P Solutions of different amounts of poly(ether) imide in mixed solvents (DMAC with THF and DMF with THF) of different compositions were prepared. Dielectric spectroscopy measurements of tan delta and conductivity were used to map the optimum region of solution parameters for electrospinning uniform nanofibres. Through digital mapping of the predictor variables (conductivity measurements, tan delta and fibre diameter), it was possible to ascertain the spinnable region of solution components. 2 refs. Cornell University (ACS,Div.of Polymeric Materials Science & Engng.) USA
Accession no.1016775
Item 103 European Polymer Journal 44, No.3, 2008, p.615. SYNTHESIS OF POLYMER-STABILIZED MAGNETIC NANOPARTICLES AND FABRICATION OF NANOCOMPOSITE FIBERS THEREOF USING ELECTROSPINNING Mincheva R; Stoilova O; Penchev H; Ruskov T; Spirov I; Manolova N; Rashkov I Polymer-stabilized magnetic nanoparticles were obtained using two biocompatible polyelectrolytes: N-carboxyethylchitosan (CECh) and poly(2-acrylamido2-methylpropanesulfonic acid) (PAMPS). The size of the particles (mean diameter 10 or 30nm, respectively) and the stability of the dispersions could be effectively controlled depending on the polyelectrolyte nature. The presence of polyelectrolyte shell was proved by transmission electron microscopy (TEM) studies and confirmed by thermogravimetric analyses. Depending on the polyelectrolyte nature the magnetic nanoparticles existed in different magnetic states - superparamagnetic or intermediate state between superparamagnetic and ferrimagnetic one, as evidenced by the measurements of the magnetisation and Mossbauer analyses. Fabrication of nanocomposite magnetic fibres with mean diameter in the range 100-500nm was achieved using electrospinning of the system CECh/ferrofluid/non-ionogenic polymer. 42 refs. Sofia,Institute of Polymers; Bulgaria,Institute for Nuclear Research & Nuclear Energy BULGARIA; EASTERN EUROPE
Accession no.1016084 Item 102 COMPOSITES: ENABLING A NEW ERA IN CIVIL AVIATION. Proceedings of the American Society for Composites:Twenty-second Technical Conference, held University of Washington, Seattle, Wa., 17th19th Sept.2007. Lancaster, Pa., DEStech Publications, 2007, Paper 162, CD-ROM, ISBN 978-1-932078-70-1 ELECTROSPUN NANO FIBERS WITH WOOL KERATION AND PEO Yi Li; Junyan Hu; El-Kamy D; Lin Li; Ko F Nano wool keratin crystals were mixed with PEO and nanocomposite fibres fabricated therefrom by electrospinning. The effects of keratin and PEO concentrations on fibre diameter were investigated and the chemical structures and morphology of the nanocomposite fibres characterised by FTIR spectroscopy and scanning electron microscopy. The regenerated wool fibres were considered potential candidates for biomedical and non-biomedical applications. 27 refs. Hong Kong,Polytechnic University; Drexel,University; British Columbia,University (American Society for Composites) CANADA; CHINA; HONG KONG; USA
Accession no.1016732
© Copyright 2008 Smithers Rapra Technology
Item 104 European Polymer Journal 44, No.3, 2008, p.602. ELECTROSPUN NANOFIBERS OF POLYFERROCENYLSILANES WITH DIFFERENT SUBSTITUENTS AT SILICON Wang J J; Dai L X; Gao Q; Wu P F; Wang X B The strained silicon-bridged [1]ferrocenophane Fe(eta-C 5 H 4 ) 2 ) SiBuMe was prepared via a facile chloride substitution reaction at the bridging atom of a readily available SiMeCl-bridged [1]ferrocenophane precursor. Thermal ring-opening polymerisation of Fe(eta-C 5 H 4 ) 2 SiBuMe and Fe(eta-C 5 H 4 ) 2 SiMe 2 afforded polyferrocenyldimethylsilane (PFDMS) and polyferrocenylbutylmethylsilane (PFBMS), respectively. Polyferrocenylsilane nanofibres were fabricated by electrospinning polymer solutions in 90wt% tetrahydrofuran and 10wt% N,N-dimethylformamide at room temperature. The effect of processing parameters such as concentration of polyferrocenylsilanes solution, applied voltage, and working distance on the diameter and morphology of resulting nanofibres were investigated. Electron diffraction patterns from polymer nanofibres revealed that PFS fibres exhibit different
57
References and Abstracts
orientation owing to variance of the side groups at silicon. 30 refs. Soochow,University CHINA
Accession no.1016082 Item 105 European Polymer Journal 44, No.3, 2008, p.566. NOVEL ELECTROSPUN POLY(EPSILONCAPROLACTONE)-BASED BICOMPONENT NANOFIBERS POSSESSING SURFACE ENRICHED IN TERTIARY AMINO GROUPS Paneva D; Bougard F; Manolova N; Dubois P; Rashkov I For the first time preparation of electrospun poly(epsiloncaprolactone) (PCL) based nanofibres possessing surface enriched in tertiary amino groups is shown. For that purpose the pair PCL and poly(epsilon-caprolactone)b-poly[(2-dimethylamino)ethyl methacrylate] (PCLb-PDMAEMA) diblock copolymers was used. PCLb-PDMAEMA copolymers were synthesised using a combination of ring-opening polymerisation and atom transfer radical polymerisation (ATRP). Nanofibres with mean diameters ranging from 400 to 800nm were obtained. Their morphology was evaluated by scanning electron (SEM) and atomic force microscopy (AFM). It was found that the morphology of the fibres depended on the weight ratio between the partners and the length of the PDMAEMA-block in the copolymers. The enrichment of the fibre surface in tertiary amino groups was studied by X-ray photoelectron spectroscopy (XPS). Increasing the copolymer content and the length of the PDMAEMA-block led to increase of the amount of tertiary amino groups on the fibre surface. The AFM analyses of the mechanical properties of the fibre surface showed that increasing the copolymer content led to decrease of the surface stiffness. The increase of the copolymer content led also to decrease of the melting temperature and the crystallinity degree in respect to PCL from the (co)polymer as determined by differential scanning calorimetry. 30 refs. Sofia,Institute of Polymers; Mons Hainaut,University BELGIUM; BULGARIA; EASTERN EUROPE; EU; EUROPEAN COMMUNITY; EUROPEAN ECONOMIC COMMUNITY; EUROPEAN UNION; WESTERN EUROPE; WESTERN EUROPE-GENERAL
Accession no.1016079 Item 106 Polymer 49, No.5, 2008, p.1266. ELECTROSPUN CELLULOSE ACETATE FIBERS CONTAINING CHLORHEXIDINE AS A BACTERICIDE Liang Chen; Bromberg L; Hatton T A; Rutledge G C
58
Submicron fibres with bactericidal properties were prepared from electrospinning of blends containing cellulose acetate (CA) as a polymer base, chlorhexidine (CHX) as a bactericidal agent, and organic titanate Ty z o r ® T E ( T T E ) a s a c r o s s - l i n ke r. A s m a l l amount of high molecular weight poly(ethylene oxide) (PEO) was incorporated into the blends to facilitate the electrospinning, and its effect on the extensional properties and spinnability of the N,Ndimethylformamide (DMF) solutions were evaluated. The CHX-containing fibre meshes were cured by TTE in the presence of water vapour, which created covalent links between the CA and CHX. The immobilisation of CHX on or within the fibres was confirmed by FTIR, Raman and XPS measurements. The resulting fibre meshes exhibited bactericidal properties on contact, due to the CHX immobilised on the fibres, and within a zone of inhibition (ZoI), due to the release of unbound CHX. The relationship of ZoI for the gram-negative Escherichia coli and the gram-positive Staphylococcus epidermidis to the amount of unbound CHX in the fibres is described by a simple diffusion model. The contact bactericidal capacity against both E. coli and S. epidermidis was assayed after complete removal of unbound CHX from the fibres. A post-spin treatment to attach CHX onto CA-PEO fibres via TTE linkers was also shown to be effective. 48 refs. Massachusetts,Institute of Technology USA
Accession no.1016031 Item 107 Composites Science and Technology 68, No.3-4, 2008, p.987. INHOMOGENEOUS TOUGHENING OF CARBON FIBER/EPOXY COMPOSITE USING ELECTROSPUN POLYSULFONE NANOFIBROUS MEMBRANES BY IN SITU PHASE SEPARATION Gang Li; Peng Li; Chen Zhang ; Yunhua Yu; Haiyang Liu; Shen Zhang; Xiaolong Jia; Xiaoping Yang; Zhongmin Xue; Ryu S A novel approach for toughening carbon fibre/epoxy composite using electrospun polysulphone (PSF) nanofibrous membranes was performed. As-received membranes were composed of nanofibres with random orientation, and were directly electrospun onto layers of carbon fibre/epoxy prepregs to toughen the composites. According to the random dispersed nanofibres in the membranes, the inhomogeneous phase separation of polysulphone, which was generated in situ along the nanofibres direction during the curing of epoxy matrix, was proposed. Owing to the aligned PSF spheres, excellent mechanical properties of composites were obtained. Mode I interlaminar fracture toughness (GIC) increased 158%, 261% and 281% by loading 1 wt%, 3 wt% and 5 wt% nanofibrous membranes, which was
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
far higher than those of the same content PSF films toughened composites. DMTA tests revealed good compatibility between nanofibrous membranes and epoxy matrix. And the flexural properties increased slightly compared to untoughened composite. 32 refs. Beijing,University of Chemical Technology; Beijing,Research & Design Institute; Chungnam,National University CHINA; KOREA
Accession no.1016000 Item 108 Journal of Applied Polymer Science 108, No.2, 15th April 2008, p.1191. MULTISCALE MECHANICAL PHENOMENA IN ELECTROSPUN CARBON NANOTUBE COMPOSITES Agic A Mechanical properties of electrospun BR elastomer reinforced with carbon nanotubes were analysed by a multiscale method. Nanofibres diameter dependence on electric field and solution concentration was estimated from experimental data. Fibre microscale effective properties were determined by homogenisation procedure using modified shear-lag model. Random fibrous network was generated according experimentally determined stochastic quantifiers. The influence of carbon nanotubes reinforcement on elastic modulus of electrospun sheet on macroscopic level was determined by finite element method. 26 refs. Zagreb,University CROATIA
Accession no.1015663 Item 109 Journal of Applied Polymer Science 108, No.2, 15th April 2008, p.969. ELECTROSPINNING OF POLYVINYL ALCOHOL NANOFIBER MATES. A REVISIT Supaphol P; Chuangchote S Electrospinning was used to fabricate mats of PVAL nanofibres from PAL solutions in reverse osmosis water. The effects of solution concentration, applied electric potential, sonication, and collection distance on morphological appearance and diameters of the fibre mats were investigated by SEM. The effect of the distance from the centre of the as-spun fibre mat on morphological appearance and diameters of the fibre was also investigated. The mechanical integrity of the PVAL fibre mats was also investigated. The use of sonication to prepare a PVAL solution caused the viscosity of the solution to decrease. 22 refs.
Item 110 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.466, ISBN 978-0-8412-7436-5, CD-ROM, 012 PREPARATION AND CHARACTERISTICS OF ULTRAFINE FIBER FROM ELECTROSPINNING OF BPDA-ODA POLY(AMIC ACID) SOLUTION Jieyu Liu; Nantao Hu; Chunhai Chen; Ce Wang Electrospinning of solutions of a polyamic acid consisting of oxydianiline (ODA) and biphenyltetracarboxylic dianhydride (BPDA), followed by imidisation resulted in an ultrafine polyimide fibre. Polymaic acid solutions of various concentrations were evaluated, and it was observed that fibre diameter depended on solution concentration. Addition of dichloromethane to the polyamic acid solution resulted in thick fibres when low polyamic acid concentrations were used. Fibres were characterised using scanning electron microscopy. 6 refs. Jilin,University (ACS,Div.of Polymeric Materials Science & Engng.) CHINA
Accession no.1015574 Item 111 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.315-316, ISBN 978-0-8412-7436-5, CD-ROM, 012 MICROPHASE SEPARATION OF BLOCK COPOLYMERS UNDER CYLINDRICAL CONFINEMENT: ELECTROSPUN FIBRES WITH INTERNAL STRUCTURE Minglin Ma; Krikorian V; Jian H Yu; Thomas E L; Rutledge G C Electrospinning of core-shell fibres where the core is a block copolymer such as poly(styrene-b-isoprene-bstyrene) and the shell is a random polymer of methyl methacrylate and methacrylic acid is described and discussed. Fibres were annealed to induce long range order, and in this process only the core was affected due to the high glass transition temperature of the shell. Two-fluid coaxial spinning was used to form the fibres. Fibres were characterised using transmission electron microscopy, and glass transition temperatures were determined by differential scanning calorimetry. 12 refs.
Chulalongkorn,University
Massachusetts,Institute of Technology (ACS,Div.of Polymeric Materials Science & Engng.)
THAILAND
USA
Accession no.1015635
Accession no.1015526
© Copyright 2008 Smithers Rapra Technology
59
References and Abstracts
Item 112 Macromolecular Bioscience 8, No.2, 11th Feb.2008, p.153. ELECTROSPUN CHITOSAN-COATED FIBERS OF POLY(L-LACTIDE) AND POLY(L-LACTIDE)/ POLY(ETHYLENE GLYCOL): PREPARATION AND CHARACTERIZATION Spasova M; Paneva D; Manolova N; Radenkov P; Rashkov I
from tetrahydrofuran. The surface structures and wettabilities of the composite films could be tuned simply by controlling the concentrations of the polymers. By choosing the correct proportion of each polymer, the wettability of the surface could be switched between superhydrophilicity and superhydrophobicity by changing the temperature from 20 degC to 50 degC. 25 refs.
The fabrication of novel micro fibrous and nanofibrous non-woven textiles by electrospinning poly(L-lactide) (PLLA) or PLLA/poly(ethylene glycol) solutions followed by coating the resulting mats with chitosan and subsequent crosslinking of chitosan with glutaraldehyde, is described. The products were characterised by SEM and fluorescence microscopy, and the haemostatic and antibacterial activity of the materials are discussed in terms of potential woundhealing applications. 34 refs.
Accession no.1015356
Sofia,Institute of Polymers; Sofia,Technological University BULGARIA; EASTERN EUROPE
Accession no.1015469 Item 113 Material Matters 3, No.1, 2008, p.19. ELECTROSPINNING: AN ENABLING TECHNIQUE FOR NANOSTRUCTURED MATERIALS Xie J; Xia Y The technique of electrospinning is reviewed in terms of the fabrication of nanofibres of natural and synthetic polymers, nanocomposites and inorganic fibres via sol-gel processes, and core-sheath, porous fibres and nanotubes, and their characterisation by SEM. Biomedical applications of electrospun nanofibres and non-woven nanofibre mats of biodegradable and biocompatible polymers such as poly(L-lactic acid) or poly(L-lactide-coepsilon-caprolactone), such as tissue engineering, vascular grafts and bone regeneration, are discussed. 28 refs. St.Louis,Washington University USA
Beijing,Chinese Academy of Sciences CHINA
Item 115 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th-29th March 2007. Washington, D. C., ACS, Division of Polymeric Materials: Science and Engineering, 2007, p. 555-556, ISBN 978-0-8412-7436-5, CD-ROM, 012 PREPARATION OF POLY(STYRENE-COMALEIC ANHYDRIDE) (SMA) HYDROGEL NANOFIBER BY ELECTROSPINNING Haiqing Liu; Chunyi Tang; Shuhai Ye Electrospinning of nanofibres of styrene-maleic anhydride copolymer (PSMA) by electrospinning from acetone, dimethylformamide (DMF) or their mixtures was examined. Because of the rapid solidification of PSMA when spun from acetone, the resulting fibres had large diameters, whereas ultrafine fibres, with diameters as small as 180 nm, were obtained by electrospinning from DMF/ acetone mixtures, because the fibres could be stretched to a greater degree before solidification occurred. The diameter of the fibres decreased with increasing proportions of DMF in the solvent mixture. Hydrolysed PSMA containing 18% maleic acid was insoluble in water, whereas those with a maleic acid content of 32 or 48% was soluble in water. Crosslinking of PSMA fibres with diethylene glycol followed by hydrolysis with sodium hydroxide in ethanol gave water-swellable hydrogel nanofibres. 4 refs. Fujian,Normal University CHINA
Accession no.1015332
Accession no.1015427 Item 114 Macromolecular Rapid Communications 29, No.6, 19th March 2008, pp.485. LOW-COST, THERMORESPONSIVE WETTABILITY OF SURFACES: POLY(NISOPROPYLACRYLAMIDE)/POLYSTYRENE COMPOSITE FILMS PREPARED BY ELECTROSPINNING Nu Wang; Yong Zhao; Lei Jiang Low-cost thermoresponsive poly(N-isopropylacrylamide)/ polystyrene blend films were prepared by electrospinning
60
Item 116 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th-29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.700-702, ISBN 978-0-8412-7436-5, CD-ROM, 012 PREPARATION OF ALIGNED POLYETHERIMIDE FIBER BY ELECTROSPINNING SungCheal Moon; HeeSun Kim; JaeKon Choi; Farris R C
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
The preparation of polyether imide fibres by electrospinning using both a stationary grounded target and a rotating grounded target is described. The effect of solution concentration and applied voltage on fibre diameter is examined. The influence of applied voltage and take-up speed on the alignment and molecular orientation of the generated fibre is also studied. 14 refs. Massachusetts,University; Chosun,University (ACS,Div.of Polymeric Materials Science & Engng.) KOREA; USA
Accession no.1015245 Item 117 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th-29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.672, ISBN 978-0-8412-7436-5, CD-ROM, 012 LIPASE-IMMOBILIZED ELECTROSPUN POLYACRYLONITRILE NANOFIBROUS MEMBRANE Jyh-Ping Chen; Sheng-Feng Li; Wen-Teng Wu Polyacrylonitrile is electrospun into nanofibrous membranes. The electrospun membrane is used for the immobilisation of lipase. The properties of polyacrylonitrile nanofibrous membranes and the activity of immobilised lipase are investigated. 3 refs. Chang Gung,University; Cheng Kung,University (ACS,Div.of Polymeric Materials Science & Engng.) TAIWAN
Accession no.1015230 Item 118 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th-29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.647, ISBN 978-0-8412-7436-5, CD-ROM, 012 ELECTROSPUN PCL/CNF SCAFFOLDS WITH CONTROLLED SURFACE CHEMISTRY Deshpande H; Jose M V; Thomas V; Clem W C; Chowdhary S; Dean D R; Nyairo E A study of the cytocompatibility of polycaprolactone carbon nanofibre composite scaffold is presented. Mesenchymal stem cells are successfully grown on the scaffold suggesting the attachment of these cells to the scaffold. Carbon nanofibres in the scaffold increase the electrophoretic deposition of nano-hydroxyapatite. 8 refs. Alabama,University at Birmingham; Alabama, State University
© Copyright 2008 Smithers Rapra Technology
(ACS,Div.of Polymeric Materials Science & Engng.) USA
Accession no.1015217 Item 119 ACS Polymeric Materials: Science and Engineering. Spring Meeting 2007. PMSE Preprints Volume 96. Proceedings of a conference held Chicago, Il., 25th-29th March 2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.622-623, ISBN 978-0-8412-7436-5, CD-ROM, 012 CONTROLLED RELEASE OF LOW MOLECULAR WEIGHT CATIONIC MOLECULES FROM ELECTROSPUN WEAK POLYELECTROLYTE FIBERS Chunder A; Sarkar S; Yingbo Yu; Lei Zhai Ultrathin fibres comprising two oppositely charged weak polyelectrolytes polyacrylic acid and polyallylamine hydrochloride are fabricated using electrospinning. The fibres are capable of controlling methylene blue release through pH change. The fibre release properties are tuned by depositing different coatings onto the fibre surface. Such fibres may be used for drug delivery devices and other controlled release applications. 8 refs. Central Florida,University (ACS,DIV.OF POLYMERIC MATERIALS SCIENCE & ENGNG.) USA
Accession no.1015207 Item 120 Polymer International 57, No.4, April 2008, p.632. CONTROLLING NUMBERS AND SIZES OF BEADS IN ELECTROSPUN NANOFIBERS Yong Liu; Ji-Huan He; Jian-Yong Yu; Hong-Mei Zeng The effects of solvent, weight concentration and salt additive on the number and morphology of beads in the electrospinning process are systematically studied. Either a suitable weight concentration or a suitable salt additive can completely prevent the occurrence of beads in the electrospinning process; solvents can affect the number of beads and the morphology of electrospun fibres. Beads are mainly caused by lower surface tension. With a higher surface tension, the size and number of beads in electrospun products are smaller and fewer respectively. 33 refs. Shanghai,Donghua University CHINA
Accession no.1015193 Item 121 Polymer 49, No.6, 2008, p.1651. VISCOELASTIC ELECTROSPUN JETS: INITIAL STRESSES AND ELONGATIONAL RHEOMETRY
61
References and Abstracts
Han T; Yarin A L; Reneker D H A novel method of characterisation of viscoelastic longitudinal stresses in electrospun jets of semi-dilute and concentrated polymer solutions and melts is introduced. The measured longitudinal stresses at the beginning of the thin jet region in the jets of a 6wt% aqueous solution of polyethylene oxide (Mw=400kDa) were of the order of 100 kPa, which is two orders of magnitude larger than in any other free viscoelastic jets issued from nozzles and orifices. This is attributed to elongation-driven stretching of polymeric liquids in the transition zone, between the preceding modified Taylor cone zone and the beginning of the thin jet region, where the stretching rates are of the order of 100-1000s-1. The Rouse relaxation times found were in the range of 3-8ms, and the moduli of elasticity were of the order of 100Pa. A novel explanation of the reasons for the formation of the straight sections in the electrospun jets is proposed. The straight sections are stabilised by the high initial longitudinal stresses in the jet generated due to strong electrically driven stretching in the transition zone. The further electrically driven stretching in the jet (after the transition zone) is relatively weak, and viscoelastic Rouse relaxation prevails. The relaxation distance of the longitudinal stresses along the jet increases with the applied voltage (which generates higher initial stresses in the transition zone) and thus the length of straight section of the jet should increase as the applied voltage increases. The results also point at an opportunity to develop an elongational rheometer for concentrated polymeric systems with stretching rates of the order of 100-1000s-1. The proposed rheometer employs excitation of electrically driven jets by single lateral pulses, and observation of the pulse propagation and widening along the jet. This reveals the level of the longitudinal stresses along the jet and allows evaluation of the viscoelastic Rouse relaxation time, modulus of elasticity and the elongational viscosity in the jet. 21 refs. Akron,University; Chicago,University of Illinois USA
Accession no.1015137 Item 122 Polymer Degradation and Stability 93, No.3, 2008, p.731. DEGRADATION PATTERNS AND SURFACE WETTABILITY OF ELECTROSPUN FIBROUS MATS Cui W; Li X; Zhou S; Weng J Degradation profiles and surface wettability are critical for optimal application of electrospun fibrous mats as drug carriers, tissue growth scaffolds and wound dressing materials. The effect of surface morphologies and chemical groups on surface wettability, and the resulting matrix degradation profiles were firstly assessed for electrospun poly(d,l-lactide) (PDLLA) and poly(d,llactide)-poly(ethylene glycol) (PELA) fibres. The air entrapment between the fibre interfaces clarified the
62
effects of various surface morphologies on the surface wettability. Chemical groups with lower binding energy were enriched on the fibre surface due to the high voltage of the electrospinning process, and a surface erosion pattern was detected in the degradation of electrospun PDLLA fibres, which was quite different from the bulk degradation pattern for other forms of PDLLA. Contributed by the hydrophilic poly(ethylene glycol) segments, the degradation of electrospun PELA fibres with hydrophobic surface followed a pattern different from surface erosion and typical bulk degradation. 29 refs. Chengdu,Southwestern Jiaotong University CHINA
Accession no.1015117 Item 123 Polymer Degradation and Stability 93, No.3, 2008, p.618. SELF-ACCELERATED BIODEGRADATION OF ELECTROSPUN POLY(ETHYLENE GLYCOL)POLY(L-LACTIDE) MEMBRANES BY LOADING PROTEINASE K Li X; Zhang H; Li H; Tang G; Zhao Y; Yuan X Proteinase K was successfully loaded inside ultrafine fibres of poly(ethylene glycol)-poly(l-lactide) (PELA) by emulsion electrospinning. A core/shell fibre structure was formed and verified by a transmission electron microscope. In vitro biodegradation of electrospun PELA membranes containing proteinase K (PELA-P) was examined in TrisHCl buffer solution at pH 8.6 and 37 deg.C in comparison with electrospun PELA membranes without proteinase K. During biodegradation, mass loss, water absorption, pH value of the incubated buffer, fibrous morphology and thermal properties were monitored. Results suggested that PELA-P membranes degraded significantly faster than PELA membranes. A significant drop in pH value of the buffer after incubation of PELA-P membranes for 1d was observed, and after 7d, PELA-P membranes lost their fibrous appearance and masses almost completely. In contrast, electrospun PELA membranes did not show any obvious changes. The obtained electrospun PELA-P membranes exhibited self-accelerated biodegradability and could benefit drug controlled release and tissue regeneration. 36 refs. Tianjin,University CHINA
Accession no.1015106 Item 124 Journal of Materials Chemistry 18, No.8, 28th Feb.2008, p.859. SOLVENT-RESISTANT ANTIBACTERIAL MICROFIBERS OF SELF-QUATERNIZED BLOCK COPOLYMERS FROM ATOM TRANSFER RADICAL POLYMERIZATION AND ELECTROSPINNING
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Fu Guo-Dong; Yao Fang; Li Zhigang; Li Xinsong Diblock copolymers of poly(((2-dimethylamino) ethyl methacrylate)-co-(glycidyl methacrylate)) (P(DMAEMA-c-GMA)) and P(DMAEMA-c-GMA)-bpoly(pentachlorophenyl acrylate) (PPCPA) were synthesised by consecutive atom transfer radical polymerisation. Microfibres were prepared by electrospinning of P(DMAEMA-c-GMA)-b-poly(pentachlorophenyl acrylate) from a solution in THF and DMF and solventresistant fibres obtained by subsequent treatment with 1,6-hexanediamine. Microfibres with high antibacterial activity were produced by combining the hydrophobic interaction of PPCPA and electrostatic interaction of quaternary ammonium salts from the self-quaternisation of P(DMAEMA-c-GMA)-b-poly(pentachlorophenyl acrylate) and the antibacterial effect of the crosslinked microfibres assayed with E coli and Staphylococcus aureus cultures. 33 refs. Nanjing,Southeast University CHINA
Accession no.1014721 Item 125 Polymer Materials Science and Engineering 23, No.6, Nov.2007, p.244. PREPARATION OF ULTRA-FINE FILAMENT NON-WOVEN COMPOSITE FABRICS WITH MULTI-SPINNERET ELECTROSPINNING Yong Xu; Xin-Sheng Zhu; Qiang Gao; Si Cheng The effects of solidification distance and voltage on the electrospinning of solutions of blends of PVAl with soluble starch and chitosan were investigated and the fabrication of ultra-fine fibre non-woven composite fabrics by multijet electrospinning attempted. The morphology, structure and mechanical properties of the composite fabrics were investigated by scanning electron microscopy, IR spectroscopy, DSC and tensile testing. The effect of solvent volatilisation on composite mat morphology and properties was examined and the mechanical properties and degree of crystallinity of nanofibre mats immersed in ethanol investigated. 9 refs. Suzhou,University CHINA
Accession no.1014682 Item 126 Journal of Applied Polymer Science 107, No.6, 15th March 2008, p.3756. CONJUGATE ELECTROSPINNING OF CONTINUOUS NANOFIBER YARN OF POLY(L-LACTIDE)/NANOTRICALCIUM PHOSPHATE NANOCOMPOSITE Xinsong Li; Chen Yao; Fuqian Sun; Tangying Song; Yunhui Li; Yuepu Pu
© Copyright 2008 Smithers Rapra Technology
Conjugate electrospinning with coupled spinnerets was used to prepare continuous nanofibre yards from a composite solution of polylactide and beta-tricalcium phosphate. In essence, two composite solutions were kept at opposite charges and the spinnerets to each were spinning in opposite directions. The two filaments, each with an opposite rotation, were then wound up together. The system was easily expanded and yarns were prepared with three pairs of oppositely charged spinnerets producing a six filament yarn. Nanofibre yarns were characterised using scanning and transmission electron microscopies and tensile testing. Biocompatibility of yarns was also evaluated in vitro, and a potential application could be for use as scaffold materials. 16 refs. Nanjing,Southeast University CHINA
Accession no.1014526 Item 127 Journal of Applied Polymer Science 107, No.6, 15th March 2008 p.3681. STRUCTURE FOR ELECTRO-SPUN SILK FIBROIN NANOFIBERS Kawahara Y; Nakayama A; Matsumura N; Yoshioka T; Tsuji M Structure of silk fibroin nanofibres, prepared by electrospinning in hexafluoropropanol solvent, was characterised by polarised optical microscopy, scanning electron microscopy and selected area electron diffraction analysis obtained using transmission electron microscopy. Collection of nanofibres was by either parallel electrodes or by a dish type collector filled with ethanol. Differences in fibre structure and crystallinity using the different collectors, and under the influence of water or ethanol were discussed. 13 refs. Gunma,University; Kyoto,Institute of Technology; Kyoto,University JAPAN
Accession no.1014516 Item 128 Journal of Applied Polymer Science 107, No.6, 15th March 2008 p.3535. STRUCTURAL CHARACTERIZATION AND DYNAMIC WATER ADSORPTION OF ELECTROSPUN POLYAMIDE6/ MONTMORILLONITE NANOFIBERS Qi Li; Qufu Wei; Ning Wu; Yibing Cai; Weidong Gao Solution mixing and electrospinning were used to prepare nanocomposite fibres of polyamide-6 (PA6) and montmorillonite clay. Viscosity and surface tension of the spinning solution were measured and it was observed that the addition of nanoclay reduced both. Fibres were characterised using scanning and transmission electron microscopies, atomic force microscopy and water absorption measurements. Fibres of smaller
63
References and Abstracts
diameter but with a rougher surface were produced by the nanocomposite. Water adsorption was increased by nanoclay addition. 10 refs. Jiangnan,University CHINA
Accession no.1014499 Item 129 Polymers for Advanced Technologies 19, No.2, Feb.2008, p.124. THERMAL AND MECHANICAL PROPERTIES OF ELECTROSPUN PMMA, PVC, NYLON 6, AND NYLON 6,6 Carrizales C; Pelfrey S; Rincon R; Eubanks T M; Kuang A; McClure M J; Bowlin G L; Macossay J The fabrication of nanofibres of poly(methyl methacrylate), poly(vinyl chloride), nylon-6 and nylon6,6 by electrospinning, and the characterisation of their morphology by SEM, thermal properties by TGA and DSC, and mechanical properties by tensile testing, is described. The effects of electrospinning on thermal stability, glass transition temperature, crystallinity, water absorption and mechanical properties of the polymers are discussed. 32 refs. Texas,Pan American University; Virginia,Commonwealth University USA
Accession no.1014374 Item 130 Journal of Biomaterials Science: Polymer Edition 19, No.2, 2008, p.245. CHARACTERIZATION OF ELECTROSPUN CORE/SHELL POLY(VINYL PYRROLIDONE)/ POLY(L-LACTIDE-CO-EPSILONCAPROLACTONE) FIBROUS MEMBRANES AND THEIR CYTOCOMPATIBILITY IN VITRO Li S; Sun B; Li X; Yuan X The fabrication of ultrafine fibrous membranes of core-shell poly(vinyl pyrrolidone)/poly(L-lactide-coepsilon-caprolactone) by coaxial electrospinning and their characterisation by SEM and TEM (structural morphology), water absorption, tensile strength, elongation at break and Young's modulus, is described. Cell adhesion, cell viability and morphology of the fibrous membranes were investigated by in-vitro studies and the results are discussed in comparison with those for poly(L-lactide-co-epsilon-caprolactone) and chitosan membranes prepared by traditional electrospinning processes in terms of potential biomedical applications. 27 refs. Tianjin,University CHINA
Accession no.1014351
64
Item 131 Journal of Physics D 41, No.2, 21st Jan.2008, Paper 025308, pp.8 MECHANICAL CHARACTERIZATION OF SINGLE HIGH-STRENGTH ELECTROSPUN POLYIMIDE NANOFIBRES Chen F; Peng X; Li T; Chen S; Wu X-F; Reneker D H; Hou H The ultimate tensile strength and axial tensile modulus of single high-strength polyimide nanofibres, fabricated by annealing electrospun nanofibres of the precursor poly(amic acid) derived from 3,3',4,4'-biphenyltetracarboxylic dianhydride and p-phenylenediamine, were determined using a novel micro-tensile testing method. The tensile failure mechanisms of the polyimide nanofibres such as chain scission, pull-out and chain bundle breakage were investigated by fractographic analysis using TEM, and chain alignment along the nanofibre axis was studied by XRD. 64 refs. Jiangxi,Normal University; NebraskaLincoln,University; Akron,University CHINA; USA
Accession no.1014306 Item 132 Journal of Applied Polymer Science 108, No.1, 2008, pp.491. ELECTROSPINNING OF DEGRADABLE ELASTOMERIC NANOFIBERS WITH VARIOUS MORPHOLOGY AND THEIR INTERACTION WITH HUMAN FIBROBLASTS Borg E; Frenot A; Walkenstrom P; Gisselfalt K; Gretzer C; Gatenholm P Artelon, a degradable poly(urethane urea) elastomer, was electrospun into scaffolds for tissue engineering. Scanning electron microscopy studies showed that the diameter of the electrospun fibres ranged from 100 nm to a few microns, with an average diameter of 750 nm. The molar mass of the polymer had a marked effect on the morphology of the scaffold. Ageing of the polymer solution caused changes in viscosity (as measured by stress sweeps, between 13.5-942 Pa) that also affected the morphology. The electrospun Artelon mats showed elongations to break that exceeding 200%. An in vitro study showed that human fibroblasts not only adhere to the surface, but also migrate, proliferate, and produce components of an extracellular matrix. 32 refs. Sweden,Institute for Fiber and Polymer Research; Chalmers,University of Technology; Artimplant AB EUROPEAN UNION; SCANDINAVIA; SWEDEN; WESTERN EUROPE
Accession no.1014247 Item 133 Journal of Applied Polymer Science 108, No.1, 2008, pp.308.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
MORPHOLOGY OF ELECTROSPUN NYLON-6 NANOFIBERS AS A FUNCTION OF MOLECULAR WEIGHT AND PROCESSING PARAMETERS Ojha S S; Afshari M; Kotek R; Gorga R E The effects of the molecular weight (30,000, 50,000, or 63,000 g/mol) and the electrospinning process conditions (solution concentration, voltage, tip-to-collector distance, and flow rate) on the morphological and mechanical properties of nylon-6 nanofibres were examined. Scanning electron microscopy studies of nylon-6 nanofibres showed that the diameter of the electrospun fibre increased with increasing molecular weight and increasing solution concentration. Increasing the molecular weight increased the density of chain entanglements in solution for a constant polymer concentration. The morphology of electrospun fibres also depended on the tip-to-collector distance and the applied voltage concentration of the polymer solution. The tensile strength and modulus increased with increasing molecular weight. 40 refs. North Carolina,State University USA
Accession no.1014224 Item 134 Fibres and Textiles in Eastern Europe 15, No.4, Oct.-Dec.2007, p.30. PREPARATION AND MORPHOLOGY OF POLY(BUTYLENE SUCCINATE) NANOFIBERS VIA ELECTROSPINNING Yong Liu; Ji-Huan He; Jian-Yong Yu Polybutylene succinate nanofibres were prepared by electrospinning using different weight concentrations of the polymer in chloroform solutions and various needle orifice diameters. The morphology of the electrospun fibres was studied by scanning electron microscopy and thermal properties and crystallisation behaviour of the fibres investigated by DSC and wide angle X-ray diffraction. The hydrolytic degradation of the fibres immersed in sodium hydroxide solution was also studied using scanning electron microscopy. 30 refs. Donghua,University CHINA
Accession no.1013938 Item 135 Macromolecular Rapid Communications 29, No.3, 1st Feb.2008, p.234. DEVELOPMENT OF PROTON CONDUCTING POLYMER MEMBRANES FOR FUEL CELLS USING SULFONATED CARBON NANOFIBRES Barroso-Bujans F; Verdejo R; Arroyo M; LopezGonzalez M D M; Riande E; Lopez-Manchado M A Details are given of a new strategy for improving the performance of EPDM polymer electrolyte membrane fuel
© Copyright 2008 Smithers Rapra Technology
cells by the addition of sulphonated carbon nanofibres. Increases in proton conductivity were compared with Nafion. Filled membranes showed improved thermal stability and mechanical properties. 22 refs. CSIC EUROPEAN COMMUNITY; EUROPEAN UNION; SPAIN; WESTERN EUROPE
Accession no.1013768 Item 136 Journal of Applied Polymer Science 107, No.5, 5th March 2008, p.3023. ALIGNMENT AND OPTIMIZATION OF NYLON 6 NANOFIBERS BY ELECTROSPINNING Bazbouz M B; Stylios G K Details are given of the production of nonwoven electrospun nylon 6 nanofibres with formic acid under different concentrations. The effects of the solution properties, electric field, spinneret-to-collect distance on the fibre uniformity, morphology and average diameter were established. Alignment and stretching of the fibres were derived by the electrostatic interactions between the positive electrode on the spinneret and the grounded disks. The gap between the disks and collection time were varied to study the degree of alignment and the density of the collected nylon 6 fibres. 49 refs. Heriot-Watt University EUROPEAN COMMUNITY; EUROPEAN UNION; UK; WESTERN EUROPE
Accession no.1013710 Item 137 Materials Letters 62, No.3, 2008, p.511. NOVEL CARBON FIBER/EPOXY COMPOSITE TOUGHENED BY ELECTROSPUN POLYSULFONE NANOFIBERS Gang Li; Peng Li; Yunhua Yu; Xiaolong Jia; Shen Zhang; Xiaoping Yang; Seungkon Ryu Novel carbon fibre/epoxy composite toughened by electrospun polysulphone (PSF) nanofibres was prepared to enhance fracture toughness of the composite, and compared the morphology and toughness to those of composite toughened by PSF films prepared by solvent method. Polysulphone nanofibres with the average diameter of 230 nm were directly electrospun onto carbon fibre/epoxy prepregs to toughen the composite. SEM observations of the polysulphone nanofibres toughened composite revealed that polysulphone spheres with uneven sizes presented uniform dispersion through interleaves of the composite, which was different from those of composite toughened by PSF films. Mode I fracture toughness (G"I"C) of the nanofibres toughened composite was 0.869 kJ/m^2 for 5.0 wt.% polysulphone nanofibres content, which was 140% and 280% higher than those of PSF films toughened and untoughened composite
65
References and Abstracts
due to the uniform distribution of polysulphone spheres. 18 refs. Beijing,University of Chemical Technology; Chungnam,National University CHINA; KOREA
Accession no.1013571 Item 138 Polymer International 57, No.2, Feb.2008 p.203. TECHNOLOGY OF ELECTROSTATIC SPINNING FOR THE PRODUCTION OF POLYURETHANE TISSUE ENGINEERING SCAFFOLDS Andrews K D; Hunt J A; Black R A Investigation of electrostatic spinning, as opposed to electrospinning, for the preparation of microfibres of polyurethane for use in scaffolds was reported. Effects of different spinning parameters such as flow rate, spray distance, grid and mandrel voltages and traverse speed on spun fibre scaffold properties were investigated using scanning electron microscopy and statistical analysis. It was shown that scaffold structure could be controlled by appropriate selection of conditions. 44 refs. Liverpool,University EUROPEAN COMMUNITY; EUROPEAN UNION; UK; WESTERN EUROPE
Accession no.1013543 Item 139 Journal of Materials Science 43, No.1, Jan.2008, p.212. FABRICATION AND CHARACTERIZATION OF A BOEHMITE NANOPARTICLE IMPREGNATED ELECTROSPUN FIBER MEMBRANE FOR REMOVAL OF METAL IONS Hota G; Kumar B R; Ng W J; Ramakrishna S The fabrication of nanocomposite fibre membranes by electrospinning from solutions of hydrophilic nylon-6 in hexafluoropropanol, or hydrophobic poly(caprolactone) in chloroform/methanol, containing boehmite nanoparticles, and their characterisation by SEM, TEM and XRD, is described. The sorption of heavy metal ions such as cadmium(II) by the nanocomposite membranes from aqueous solution was investigated by AAS and the results are discussed. 19 refs. Rourkela,National Institute of Technology; Singapore,National University INDIA; SINGAPORE
Accession no.1013507 Item 140 Polymer International 57, No.3, 2008, pp.385. ELECTROSPINNING FUNCTIONAL NANOSCALE FIBERS: A PERSPECTIVE FOR THE FUTURE
66
Hunley M T; Long T E Recent advances in electrospun fibres for functional applications are reviewed with particular attention to the advantages these non-woven fibre scaffolds and proposed technologies for their manufacture. Electrospinning, in which a strong electric potential is applied to a polymer solution or melt to produce nano-scale fibres, has grown from a niche process to a technique that is widely used for fibre production. These nanofibres form non-woven textile mats, oriented fibrous bundles, or even three-dimensional structured scaffolds; all these constructions have large surface areas and high porosities. Among the applications of electrospun membranes are tissue engineering, controlled drug delivery, sensing, separations, filtration, catalysis and nanowires. 32 refs. Virginia,Polytechnic Institute & State University USA
Accession no.1013374 Item 141 Journal of Polymer Science: Polymer Physics Edition 46, No.5, 1st March 2008, p.460. SOLVENT AND CONCENTRATION EFFECTS ON THE PROPERTIES OF ELECTROSPUN POLY(ETHYLENE TEREPHTHALATE) NANOFIBER MATS Veleirinho B; Rei M F; Lopez Da Silva J A The preparation and characterisation of nanofibrous mats obtained by electrospinning poly(ethylene terephthalate) (PET) solutions in trifluoroacetic acid/dichloromethane is described. Special attention is paid to the effect of polymer concentration and solvent properties on the morphology, structure and mechanical and thermal properties of the electrospun nonwovens. Results show that the spinnable concentration of PET solution is above 10 wt%. Mats have nanofibrous morphology with fibres having an average diameter in the range of 200-700 nm and an interconnected pore structure. Higher solution concentrations favour the formation of uniform fibres without beads and with higher diameter. Morphology and fibre assembly change with solvent properties. Mechanical properties and thermal properties are studied for the PET electrospun nanomats and compared with those of the original polymer. Solvent effects on fibre crystallinity are not significant but a complex effect is observed on the mechanical properties of the electrospun mats as a consequence of the different structural organisation of the fibres within the mat network. 32 refs. Aveiro,Universidade EUROPEAN COMMUNITY; EUROPEAN UNION; PORTUGAL; WESTERN EUROPE
Accession no.1013203 Item 142 European Polymer Journal 44, No.1, 2008, p.1.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
NOVEL MECHANISM FOR SPINNING CONTINUOUS TWISTED COMPOSITE NANOFIBER YARNS Bazbouz M B; Stylios G K Highly aligned and twisted composite Nylon 6 nanofibres incorporating multiwall carbon nanotubes (MWCNTs) were successfully electrospun, using a novel mechanism. It has been found that; ultrasound combined with high speed shearing is the simplest and most convenient method to improve the dispersion of MWCNTs into a polymer matrix with a certain loading. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were conducted to characterize the morphology of nanofibres, the dispersion of MWCNTs and their alignment inside the fibre body. By manipulating the electrical forces during electrospinning and applying mechanical stretching to the electrospun nanofibres, high polymer chain orientation and better alignment of the MWCNTs particles along the fibre axis was achieved. Twist was applied to the nanofibres for providing the required inter fibre lateral cohesion interaction and friction thus, spinning a continuous twisted composite yarn. SEM images show twisted yarns with diameters ranging between 5 and 10 micrometer. The twist effect of the parallel bundle was investigated by controlling the twist per unit length using a motor speed controller at values of 100, 250, 500, 750 and 1000 rpm. The paper also provides a comprehensive review of various yarn spinning mechanisms of electrospun nanofibres. 72 refs. Heriot-Watt University EUROPEAN COMMUNITY; EUROPEAN UNION; UK; WESTERN EUROPE
Accession no.1013107 Item 143 Materials Letters 62, No.6-7, 2008, p.828. THERMAL RADIATIVE PROPERTIES OF ELECTROSPUN SUPERFINE FIBROUS PVA FILMS Huijun Wu; Jintu Fan; Xiaohong Qin; Guoge Zhang This paper reports on an experimental investigation of the thermal radiative properties of electrospun superfine fibrous PVA films containing or without containing TiO"2 nanoparticles. Fourier transform infrared spectroscopy was used to measure the spectral transmission of the superfine fibrous PVA films, from which the Rosseland extinction coefficients and thermal radiative conductivities of the samples were then calculated. The results showed that electrospun fibrous PVA and PVA/TiO"2 films had significantly greater Rosseland extinction coefficients and lower thermal radiative conductivities than the conventional polymer foams (e.g. PE and PU). The field emission scanning electron microscopy (FE-SEM) images showed that the electrospun PVA fibres had the diameters in range of 150-300 nm. The super fineness of the fibres in the PVA films is believed to be the main reason for the reduction of thermal radiative conductivity. The study
© Copyright 2008 Smithers Rapra Technology
also showed that the addition of TiO"2 nanoparticles can increase the thermal insulating performance of the electrospun fibrous materials. 17 refs. Hong Kong,Polytechnic University; Shanghai, Donghua University CHINA; HONG KONG
Accession no.1013062 Item 144 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston, Ma., 19th-23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.53-54, CD-ROM, 012 INITIAL AND SEQUENTIAL SURFACE MODIFICATION OF ELECTROSPUN NANO/ MICROFIBERS Xiao-Yu Sun; Qing Peng; Boerner H G; Parsons G N; Spontak R J The surface modification of electrospun nano/microfibres was described. Using the initial surface modification approach, a novel hybrid diblock copolymer containing PEO as the anchor block and an oligopeptide as the functional block was mixed with the bulk PEO polymer in aqueous solution. During electrospinning, the peptide functional groups of the copolymer migrated on to the fibre surface, leading to surface enrichment of the biofunctional peptide blocks. Sequential surface modification of electrospun PVAL or peptide filaments at the sub-micron and nanoscale level was carried out by atomic layer deposition of aluminium oxide. The substrate was removed by calcination in air at 400 deg.C. This procedure successfully controlled the thickness of the tube wall. 5 refs. North Carolina,State University; Max-Planck-Institut fuer Kolloid- & Grenzflaech. (ACS,Div.of Polymeric Materials Science & Engng.) EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; USA; WESTERN EUROPE
Accession no.1012849 Item 145 Macromolecules 41, No.1, 8th Jan.2008, p.128. ELECTROSPINNING AND SOLUTION PROPERTIES OF NAFION AND POLYACRYLIC ACID Chen H; Snyder J D; Elabd Y A The electrospinning performance and solution properties of Nafion PTFE and its blend with polyacrylic acid were investigated. Attempts to electrospin pure Nafion at various polymer concentrations, solvents, neutralisation, and electrospinning conditions resulted in electrospraying rather than electrospinning. Dynamic light scattering on
67
References and Abstracts
pure Nafion solutions in various solvents revealed large aggregates of various sizes due to polymer backbone and ionic interactions. The addition of polyacrylic acid to Nafion modified the ionic strength of the solvent resulting in suppressed aggregate formation, increased viscosity, and subsequently enhanced polymer chain entanglement. Thermal treatment enhanced water stability of the electrospun blend fibres. 31 refs. Drexel,University USA
Accession no.1012549 Item 146 Materials Letters 62, No.4-5, 2008, p.699. AFM-BASED VOLTAGE ASSISTED NANOELECTROSPINNING Yiquan Wu; Johannes M S; Clark R L This paper describes an atomic force microscope (AFM) based voltage-assisted electrospinning technique. Single nanofibres on substrates are prepared via simultaneous preparation and deposition. In this work, an AFMbased electrospinning process is developed to generate polyethylene oxide (PEO) polymeric single fibres with nanometre scale diameters. The results demonstrate the feasibility of this developed approach for assembling nanofibres at predetermined positions. This work represents a promising advancement in nanomanufacturing of one-dimensional nanostructured materials for microand nanoscale devices. 23 refs. Duke,University USA
Accession no.1012448 Item 147 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston, Ma., 19th-23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.966-967, CD-ROM, 012 ELECTROSPINNING AND SURFACE PROPERTIES OF CHITOSAN/PEO NANOFIBERS Desai K; Kit K; Jiajie Li; Zivanovic S; Davidson P M The formation of uniform sized electrospun fibres in different size ranges of chitosan blends with polyethylene oxide is described. Fibre formation and size is influenced by blend ratio, polymer concentration and solvent. Heating the polymer solution during spinning helps improve spinnability. TGA analysis confirms the presence of both polymer sin the fibres and their blend ratio remains unaltered. High molecular weight chitosan blend fibres show the highest surface activity with higher metal binding capacity. 3 refs. Tennessee,University at Knoxville
68
(ACS,Div.of Polymeric Materials Science & Engng.) USA
Accession no.1012153 Item 148 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston, Ma., 19th-23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.904, CDROM, 012 COUPLED ELECTROSPINNING OF CONTINUOUS POLY(VINYLIDENEFLUORIDECO-HEXAFLUOROPROPYLENE) NANOFIBER YARNS Tangying Song; Xinsong Li Coupled electrospinning is used to fabricate poly(vinylidene fluoride-co-hexafluoropropylene) continuous nanofibre yarns which may have potential applications for knitting to prepare protective clothing. Solution concentration and distance between the two spinnerets are found to be the main factors influencing the morphology of the yarns. The morphological and mechanical properties are presented. 5 refs. Nanjing,Southeast University (ACS,Div.of Polymeric Materials Science & Engng.) CHINA
Accession no.1012122 Item 149 Journal of Polymer Science: Polymer Physics Edition 46, No.3, 1st Feb.2008, p.305. UNIAXIALLY ALIGNED CARBON NANOFIBERS DERIVED FROM ELECTROSPUN PRECURSOR YARNS Okuzaki H; Takahashi T; Hara Y; Hu Yan Poly(p-xylenetetrahydrothiophenium chloride) was electrospun into centimetre-long yarns vertically on the surface of an electrode and parallel to the electric field and the yarns carbonised at 600 to 1000 degree C to give uniaxially aligned carbon nanofibres with average diameters of 1257 to 184 nm. The effects of concentration, spinning rate and viscosity of the polymer solution and applied voltage on yarn diameter were investigated and changes in the morphology and microstructures of the carbonised yarns examined by Raman spectroscopy. 22 refs. Yamanashi,University JAPAN
Accession no.1011856 Item 150 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Proceedings of a conference held Boston, Ma., 19th23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.452-453, CD-ROM, 012 ELECTROSPUN ENZYME-CARRYING POLYURETHANE NANOFIBERS FOR USE IN BIOSENSORS Narayanan R; Songtao Wu; Reneker D H; Ping Wang A method of electrospinning polyurethane-enzyme solutions to give high loadings of an enzyme (glucose oxidase) on the spun nanofibres was demonstrated. Fibres were characterised using scanning electron microscopy, and it was shown that fibre morphology was very dependent on concentration of spinning solution. Enzyme loading on fibres with respect to spinning time was also investigated, but enzyme activity was found not to be very dependent on enzyme loading. 5 refs. Minnesota,University; Akron,University (ACS,Div.of Polymeric Materials Science & Engng.)
by electrospinning of PAN solution using DMF as solvent. Morphology of the nanofibres for varying concentration and applied voltage was investigated by field emission SEM. The thermal properties and structural changes during the oxidative stabilisation process were primarily investigated by DSC, TGA, and FTIR and Raman spectroscopy. The nanofibre diameters increased as the applied voltage was increased and they also increased with an increase in the concentration of the polymer solution. It was also concluded that the electrospun fibres displayed a very sharp exothermic peak at 297.34 deg C. A transition temperature observed by FTIR and Raman was approximately 300 deg C, which was closely consistent with the results of DSC and TGA studies. It was also found that oxidative stabilisation in air was accompanied by a change in colour of nanofibre webs. 39 refs. Zhongyuan,University of Technology; North China,Institute of Science and Technology CHINA
Accession no.1011122
USA
Accession no.1011630 Item 151 Advanced Materials 19, No.23, 3rd Dec.2007, p.4244. MAGNETICALLY ANISOTROPIC COBALT AND IRON NANOFIBERS VIA ELECTROSPINNING Graeser M; Bognitzki M; Massa W; Pietzonka C; Greiner A; Wendorff J H
Item 153 Advanced Materials 19, No.21, 5th Nov.2007, p.3707. FIBER-ORIENTED LIQUID CRYSTAL POLARIZERS BASED ON ANISOTROPIC ELECTROSPINNING Yingfang Yao; Zhong-Ze Gu; Jizhong Zhang; Chao Pan; Yiyun Zhang; Hongmei Wei
The fabrication of cobalt and iron nanofibres with ferromagnetic properties via electrospinning from solutions of poly(vinyl butyral)(PVB) as matrix polymer in the presence of cobalt nitrate or iron(III) nitrate, and post-treatment by thermal annealing of the nanocomposite fibres in a hydrogen atmosphere leading to quantitative degradation of PVB, is described. The metal nanofibres were characterised by EDX, TEM, WAXS and SQUID magnetometry, and the results are discussed in terms of anisotropy of magnetisation. 37 refs. Marburg,Philipps Universitat; Marburg,Zentrum fuer Materialwissenschaften
A novel fibre-oriented scattering polariser was prepared by infiltrating liquid crystal into an aligned-fibre film, which was fabricated by using an optimised strategy of anisotropic electrospinning. PMMA was chosen for the fibre fabrication and the liquid crystal was SLC-100. The liquid crystal molecules were efficiently oriented, resulting in a polarising efficiency as high as 0.92. The new-style polariser had a high polarising efficiency, was simple to fabricate and had uniform and controllable optical characteristics. It could be used in flat-panel displays, antiglare sunglasses, photography filters or optical instruments. 27 refs. Nanjing,Southeast University
EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1011096
CHINA
Accession no.1011564 Item 152 Journal of Polymer Research 14, No.6, Dec.2007, p.467. CHARACTERIZATION ON OXIDATIVE STABILIZATION OF POLYACRYLONITRILE NANOFIBRES PREPARED BY ELECTROSPINNING Wang-xi Zhang; Yan-zhi Wang; Chun-feng Sun Ultrafine PAN fibres, as a precursor of carbon nanofibres, with diameters in the range of 220-760 nm were obtained
© Copyright 2008 Smithers Rapra Technology
Item 154 Advanced Materials 19, No.21, 5th Nov.2007, p.3702. FABRICATION OF ALIGNED FIBROUS ARRAYS BY MAGNETIC ELECTROSPINNING Dayong Yang; Bo Lu; Yong Zhao; Xingyu Jiang A facile and effective method was developed for the generation of well-aligned polymeric micro- and nanofibres over large areas. Electrospinning of magnetic nanoparticledoped polymers under the influence of a magnetic field was shown to produce aligned arrays of fibres over large
69
References and Abstracts
areas. The polymer used was PVAl and the magnetic nanoparticles were of Fe"3O"4. These nanofibres could be transferred onto the surfaces of other substrates. They could also be stacked into multilayer grids. The embedded magnetic nanoparticles did not affect the morphology of the fibres. 44 refs. China,National Centre for Nanoscience and Technology; Peking,University; Beijing,Institute of Chemistry; Beijing,Graduate School CHINA
Accession no.1011095 Item 155 Advanced Materials 19, No.21, 5th Nov.2007, p.3664. PATTERNING OF ELECTROSPUN FIBERS USING ELECTROCONDUCTIVE TEMPLATES Daming Zhang; Jiang Chang Electrospun mats with complex ordered architectures were fabricated by using patterned conductive collectors. The effects of the diameter of the web wires and the protrusions on the formation of the patterns of the fibrous materials were determined and woven structures that were generated by a time-dependent control of the arrangement of the protrusions in the collector were observed. The material used was D,L-poly(lactic acid) dissolved in a mixture of DMF and THF. The technique is expected to be of use in the fabrication of patterned and woven structured fibrous mats for industrial and biomedical applications. 16 refs. Shanghai,Institute of Ceramics CHINA
Accession no.1011092 Item 156 Advanced Materials 19, No.21, 5th Nov.2007, p.3544. ELECTROSPINNING PH-RESPONSIVE BLOCK COPOLYMER NANOFIBERS Linge Wang; Topham P D; Mykhaylyk O O; Howse J R; Bras W; Jones R A L; Ryan A J Ultrafine fibres of a pH-responsive triblock copolymer with different diameters, alignment, and microdomain order were prepared via electrospinning in THF/DMF and solvent-vapour annealing in THF. The monodisperse block copolymer was poly(methyl methacrylate)-bpoly(2-diethylamino)ethyl methacrylate-b-poly(methyl methacrylate). Fibrous samples displayed much quicker response times than the corresponding films owing to the increase in external surface area. The fibrils of annealed, aligned, electrospun fibres showed a dramatic apparent 'one-dimensional' pH-induced size-change during the experiment. The results were of importance in the development of responsive macromolecular actuators. 29 refs.
70
Sheffield,University EUROPEAN COMMUNITY; EUROPEAN UNION; UK; WESTERN EUROPE
Accession no.1011085 Item 157 Chinese Journal of Polymer Science 26, No.1, Jan.2008, p.63. CONTROL OF DIMENSIONAL STABILITY AND DEGRADATION RATE IN ELECTROSPUN COMPOSITE SCAFFOLDS COMPOSED OF POLY(D,L-LACTIDE-CO-GLYCOLIDE) AND POLY(EPSILON-CAPROLACTONE) Yi-Jie Liu; Hong-Liang Jiang; Yan Li; Kang-Jie Zhu Fibres were prepared by electrospinning blends of poly(D,L-lactide-co-glycolide) and poly-epsiloncaprolactone and the effect of blend composition on the morphology, shrinkage and degradation behaviour in a phosphate buffer solution of the fibres investigated using various methods, including scanning electron microscopy, DSC, wide-angle X-ray diffraction and NMR spectroscopy. It was found that degradation rate could be modulated by blend composition and that meshes containing 20% poly-epsilon-caprolactone exhibited stable dimensional morphology with degradation. 25 refs. Zhejiang,University CHINA
Accession no.1010874 Item 158 Iranian Journal of Polymer Science and Technology 20, No.5, Dec.2007-Jan.2008, p.437. THE STUDY ON ELECTROSPINNING OF NANOFIBERS FROM SODIUM ALGINATE AND THE EFFECTS OF DIFFERENT CO-SOLVENTS ON ELECTROSPINNING OF POLYMER SOLUTION Safi S; Ghiaci M; Morshed M; Hosseni A K The electrospinnability of sodium alginate was investigated using different organic solvents and surfactants. In order to improve polymer solubility in organic solvents, ammonium alginate and alginic acid were used instead of sodium alginate. Electrospinning was achieved by blending sodium alginate with PEO. Interactions between sodium alginate and PEO were examined by FTIR spectroscopy and the morphology and diameter of the fibres investigated by optical microscopy and scanning electron microscopy. Measurement of solution properties showed a marked dependence of spinnability and fibre morphology on solution viscosity and alginate to PEO blend ratio. 26 refs. Isfahan,University of Technology IRAN
Accession no.1010791
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 159 Journal of Applied Polymer Science 107, No.3, 5th Feb.2008, p.1954. ELECTROSPINNING OF ULTRAFINE CELLULOSE FIBERS AND FABRICATION OF POLYBUTYLENE SUCCINATE BIOCOMPOSITES REINFORCED BY THEM Han S O; Son W K; Youk J H; Park W H Electrospinning conditions for ultrafine cellulose fibres was studied and polybutylene succinate biocomposites reinforced by the ultrafine cellulose fibres were fabricated. The cellulose fibres were electrospun from cellulose solutions in methyl morpholine oxide. Melt processability, thermal resistance and chemical resistance were examined. 23 refs. Korea,Institute of Energy Research; Chungnam,National University; Inha,University KOREA
Accession no.1010691 Item 160 Journal of Applied Polymer Science 107, No.4, 15th Feb.2008 p.2211. ENHANCED MECHANICAL PROPERTIES OF MULTILAYER NANO-COATED ELECTROSPUN NYLON 6 FIBERS VIA A LAYER-BY-LAYER SELF-ASSEMBLY Jong Hoon Park; Byoung Suhk Kim; Yeon Chun Yoo; Myung Seob Khil; Hak Yong Kim Electrospun polyamide-6 mats were coated by polystyrenesulphonate and polyallylamine hydrochloride polyelectrolytes using a layer by layer self assembly technique involving multiple dipping. Nanofibre mats were characterised using scanning electron microscopy and tensile testing. Coated polyamide fibres exhibited a more uniform and smooth appearance, and mechanical properties were improved significantly compared to the uncoated electrospun mats. Reasons for the improvements were discussed. 30 refs.
diisocyanate and hydroxyethyl methacrylate, with the addition of a copolymer of hydroxylvalerate and hydroxylbutyrate added as a process aid, is described. Fibres had good thermal and solvent stability, and were characterised using Fourier transform infrared spectroscopy, scanning electron microscopy, solvent absorption and thermogravimetric analysis. 35 refs. Donghua,University; Dresden,University of Technology CHINA; EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1010567 Item 162 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston, Ma., 19th23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.609-610, CD-ROM, 012 PREPARATION OF ELECTROSPUN CELLULOSE MEMBRANE FOR EAPAP ACTUATOR Eun-Hee Lee; Hye-Mi Kim; Kwang-Sok Kim; In-Joo Chin Preparation of a nanofibre cellulose membrane for application in electroactive paper actuator applications was described and discussed. Effects of fibre alignment and crystallinity were investigated. Scanning electron microscopy, elemental analysis, X-ray diffraction and displacement measurements by laser sensors when electroactivated were used to examine the fibres. It was observed that fibre alignment was in the stretching direction, with bending displacement characteristics improved compared to randomly oriented membranes. 14 refs. Inha,University (ACS,Div.of Polymeric Materials Science & Engng.) KOREA
Accession no.1010538
Chonbuk,National University; Sogang,University KOREA
Accession no.1010576 Item 161 Journal of Applied Polymer Science 107, No.4, 15th Feb.2008 p.2142. FABRICATING NOVEL THERMAL CROSSLINKED ULTRAFINE FIBERS VIA ELECTROSPINNING Tian-He Dai; Hao Yu; Kai Zhang; Mei-Fang Zhu; YanMo Chen; Adler H-J Electrospinning of polyester macromers from dichloromethane solution, followed by thermal crosslinking was used to prepare ultrafine fibres. Synthesis of the polyester macromer from a diol polymer, isophorone
© Copyright 2008 Smithers Rapra Technology
Item 163 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston, Ma., 19th23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.522-523, CD-ROM, 012 ELECTROSPINNING OF THIOLATED POLY(VINYL ALCOHOL)/WHEAT GLUTEN FIBRES Jing Dong; Parnas R; Asandei A D Electrospinning of composites of thiolated polyvinyl alcohol, wheat gluten and with or without dithiothreitol was achieved and the resulting fibres were characterised
71
References and Abstracts
by scanning electron microscopy. Spinning solutions consisted of mixed solutions of the three ingredients, and the effects of different concentrations of wheat gluten and dithiothreitol on spinning and the morphology of the resulting fibres were investigated. Solubility of the wheat gluten was improved by polymer addition but no by dithiothreitol addition. 10 refs. Connecticut,University (ACS,Div.of Polymeric Materials Science & Engng.) USA
Accession no.1010513
condensation therefore contributes to the control of the mean interfibre distance and the resulting porosity. This simple and well accessible use of ice crystals as void templates gives access to the preparation of biodegradable tissue engineering scaffolds with an up to four times higher porosity if compared to conventional fibre electrospinning. The successful application of low-temperature electrospinning using polyesters or polyurethanes suggests a broad, material independent applicability of the process for the preparation of highly porous polymer structures. 46 refs. ETH Zurich
Item 164 Polymer Engineering and Science 47, No.12, 2007, p.2065. EXPLOITATION OF ELECTRIC FIELD IN CONTROLLING OF NANOFIBER SPINNING PROCESS Heikkilae P; Soederlund L; Uusimaeki J; Kettunen L; Harlin A Nanofibres can be prepared from a polymer solution utilizing electrospinning, a method exploiting an electrostatic field. In this work the electric field of the electrospinning process was modelled for better understanding and controllability of the fibre deposition in the electrospinning process. The model of the electric field was compared with experimental observations. The model of the electric field explained many phenomena in electrospinning, but did not provide an exclusive control tool for the process. 39 refs. Tampere,University of Technology EUROPEAN UNION; FINLAND; SCANDINAVIA; WESTERN EUROPE
Accession no.1010416 Item 165 Polymer Engineering and Science 47, No.12, 2007, p.2020. ULTRAPOROUS 3D POLYMER MESHES BY LOW-TEMPERATURE ELECTROSPINNING: USE OF ICE CRYSTALS AS A REMOVABLE VOID TEMPLATE Simonet M; Schneider O D; Neuenschwander P; Stark W J While electrospinning provides an excellent preparation method for the manufacturing of polymer fibres with defined diameter, controlling the overall porosity of the resulting fibre assemblies has remained elusive, particularly at higher porosities. In this study, the use of a low-temperature fibre collection device in air with controlled humidity allowed the simultaneous deposition of polymer fibres and ice particles from condensing humidity. The ice particles were intimately embedded within the polymer fibres and served as a pore template thus defining the mesh porosity after drying of the collected fibre assemblies. The amount of water
72
SWITZERLAND; WESTERN EUROPE
Accession no.1010410 Item 166 Polymer Materials Science and Engineering 23, No.5, Sept.2007, p.167/173 THE INFLUENCE OF PASS SOLUTION CHARACTERISTIC ON THE SOLUTION ELECTROSPINNABILITY AND MORPHOLOGY OF THE NANOFIBERS Gang Zhang; Heng-Mei Huang; Xiao-Jun Wang; XiaoChuan Zhao; Jie Yang; Guang-Xian Li Polyarylene sulphide sulphone (PASS) solutions were prepared using a mixed solvent system (phenol/1,1,2,2tetrachlorothane and the effects of dynamic viscosity, conductivity and surface tension of the solutions on electrospinning, bead formation and average nanofibre diameter investigated. 6 refs. Sichuan,University CHINA
Accession no.1009944 Item 167 Polymer Materials Science and Engineering 23, No.5, Sept.2007, p.132. EFFECT OF HIGH VALENCE METAL IONS ON THE ELECTROSPINNABILITY OF POLY(VINYL ALCOHOL) AQUEOUS SOLUTION De-Tao Xu; Xin-Sheng Zhu; Yong Xu; Wei-Jian Gao The electrospinning of various PVAl aqueous solutions was investigated and the electrical conductivity, surface tension and viscosity of the solutions examined as a function of PVAl concentration. The effects of ethylene diamine tetraacetic acid and calcium chloride on electrospinning were evaluated and the metal content of the samples studied by elemental analysis. 9 refs. Suzhou,University CHINA
Accession no.1009935 Item 168 Advanced Functional Materials 17, No.17, 23rd Nov.2007, p.3650.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
ELECTROSPINNING: A FACILE METHOD TO DISPERSE FLUORESCENT QUANTUM DOTS IN NANOFIBERS WITHOUT FORSTER RESONANCE ENERGY TRANSFER Minjie Li; Junhu Zhang; Hao Zhang; Yifei Liu; Chunlei Wang; Xiang Xu; Yue Tang; Bai Yang
be applied to other combinations of polymers and salts. Fibres were illustrated using scanning electron microscopy. 5 refs. North Carolina,State University (ACS,Div.of Polymeric Materials Science & Engng.)
Fluorescent CdTe quantum dots were dispersed into PVAl solid nanofibres by electrospinning of a quantum dot/PVAl blend solution and the resulting materials characterised by fluorescence spectroscopy, TEM, scanning electron microscopy and differential scanning calorimetry. The quantum dots were well separated in the nanofibres and no Forster resonance energy transfer occurred even when multi-colour quantum dots were incorporated. 22 refs.
Accession no.1009674
Jilin,University CHINA
Accession no.1009873 Item 169 Journal of Applied Polymer Science 107, No.3, 5th Feb.2008, p.1547. MATERIALS SELECTION AND RESIDUAL SOLVENT RETENTION IN BIODEGRADABLE ELECTROSPUN FIBERS Nam J; Huang Y; Agarwal S; Lannutti J Details are given of the development of a method to quantify hexafluoropropanol sterilizing agent retention following electrospinning of gelatin, polycaprolactone, and polycaprolactone-gelatin blends using electro-spray mass spectroscopy. The acetone content of acetone-spun polycaprolactone was also examined. Potential uses in tissue engineering are mentioned. 48 refs.
USA
Item 171 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston,Ma., 19th-23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.705-706, CD-ROM, 012 ELECTROSPINNING OF POLYISOBUTYLENE THERMOPLASTIC ELASTOMERS Taghizadeh S N; Faust R; Mead J The effects of process parameters on the properties of nonwoven mats of styrene-isobutylene-styrene triblockcopolymer based electrospun from tetrahydrofuran solution were examined. Fibres made from a 12 wt% solution had reasonable fibre diameters, but because of the presence of significant beading of the fibres, this concentration was not suitable for the preparation of mats of uniform nanofibres. Fibres made from 20 wt% solution electrospun at 8-12 kV and tip-to-target distances of 10-15 cm showed a relatively uniform fibre morphology but rather large fibre diameters. Typically, high solution concentrations produced large pore diameters in the nanofibre mats. 6 refs. Lowell,Massachusetts University (ACS,Div.of Polymeric Materials Science & Engng.)
Ohio,State University
USA
USA
Accession no.1009496
Accession no.1009822 Item 170 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston,Ma., 19th23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.762-763, CD-ROM, 012 SALT-INDUCED ELECTROSPINNING METHOD FOR PRODUCING POROUS NYLON 6 NANOFIBERS Afshari M; Gupta A; Zhang X; Tonelli A; Khan S; Kotek R Production of nanoscale porous fibres of polyamide-6 (PA6) from a Lewis acid based complex of PA6 and gallium trichloride, by electrospinning, is described. Removal of the gallium trichloride after spinning resulted in uniform porosity. The method proved an economical route for preparation of porous nanofibres and could
© Copyright 2008 Smithers Rapra Technology
Item 172 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston,Ma., 19th23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.657-658, CD-ROM, 012 PREPARATION OF ELECTROSPUN MEMBRANE FOR LOW-FOULING ULTRAFILTRATION Park C-H; Kirn K-S; Chin I-J A low-fouling ultrafiltration membrane was produced by combining a UV-curable polyurethane and an electrospun poly(acrylonitrile)/poly(ether sulphone) membrane and the polyurethane-coated membrane was characterised by means of scanning electron microscopy and contactangle measurements. In filtration tests under crossflow conditions, the double-layered membrane showed an oil retention of over 99% and an oil concentration of less
73
References and Abstracts
than 10 mg/L in the filtrate. The polyurethane-coated electrospun PAN/PES membrane is suitable for the treatment of oil-contaminated wastewater. 6 refs. Inha,University; Small Business Training Institute (ACS,Div.of Polymeric Materials Science & Engng.) SOUTH KOREA
Accession no.1009472 Item 173 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston,Ma., 19th-23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.655-656, CD-ROM, 012 ALIGNMENT OF MWNTS USING ELECTROSPUN MWNT-G-PLLA NANO-FIBERS Jang Y-W; Park C-H; Chin I-J Oxidised multi-wall carbon nanotubes (MWNTs) were treated with poly(ethylene glycol) (PEG) and then covalently functionalised with L-lactide by ring-opening polymerisation. The PEG and poly(L-lactic acid) (PLLA) were shown to be covalently bonded to the MWNTs. PLLA/MWNT composite nanofibres were prepared by electrospinning. Scanning and transmission electron microscopy showed that welloriented electrospun fibres and MWNT arrays were obtained. Electrospinning of mixtures of PLLA and MWNT-g-PLLA was shown to be a flexible approach for aligning MWNTs within the PLLA nanofibres. 10 refs. Inha,University (ACS,Div.of Polymeric Materials Science & Engng.) SOUTH KOREA
Accession no.1009471 Item 174 ACS Polymeric Materials: Science and Engineering. Fall Meeting 2007. PMSE Preprints Volume 97. Proceedings of a conference held Boston,Ma., 19th-23rd Aug.2007. Washington, D.C., ACS, Division of Polymeric Materials: Science & Engineering, 2007, p.630-631, CD-ROM, 012 ELECTROSPINNING OF SELF-ASSEMBLED INCLUSION COMPLEXES OF POLY(ETHYLENE OXIDE) WITH UREA Liu Y; Pellerin C Micro-sized fibres of inclusion complexes of poly(ethylene oxide) in urea were prepared by electrospinning and characterised by means of IR spectroscopy and wideangle X-ray diffractometry (WAXD). WAXD showed the presence of a high degree of molecular orientation; this explains the high relative thermal stability of the inclusion complexes. 9 refs. Montreal,University (ACS,Div.of Polymeric Materials Science & Engng.)
74
CANADA
Accession no.1009457 Item 175 Polymer International 57, No.1, Jan.2008, p.77. PRODUCTION OF SUPERHYDROPHOBIC POLYMER FIBERS WITH EMBEDDED PARTICLES USING THE ELECTROSPINNING TECHNIQUE Menini R; Farzaneh M Polymer mats made of polystyrene and poly(tetrafluoroethylene-co-(vinylidene fluoride)-copropylene) (PTVFP) are prepared by electrospinning. They are found to show highly hydrophobic properties with a water contact angle between 130 and 150 deg. A dual fibrebead microstructure is observed. Superhydrophobicity is reached when PTVFP mats are electrospun from a polymer solution containing dispersed polytetrafluoroethylene (PTFE) nanoparticles. Using AFM imaging protruding nanosized asperities are observed on fibre and bead surfaces and this structure leads to superhydrophobic properties. Materials prepared from a high-viscosity PTVFP/ethyl acetate solution with PTFE particles, show an improvement in hydrophobicity compared to the materials obtained from a particle-free polymer solution. 34 refs. Quebec,University; Hydro-Quebec CANADA
Accession no.1009334 Item 176 Journal of Functional Polymers 19-20, No.3, Sept.2007, p.277. PREPARATION AND CHARACTERIZATION OF PLLA/BETA-TCP HYBRID MEMBRANE VIA ELECTROSPINNING Yun Zhou; Xiao-Ping Yang; Yun-Hua Yu; Peng Li; XuLiang Deng; Guo-Qiang Chen beta-Tricalcium phosphate/poly(L-lactic acid) hybrid membranes for bone tissue regeneration were prepared by electrospinning and the structural and morphological properties of the beta-tricalcium phosphate particles investigated by FTIR spectroscopy, X-ray diffraction, TEM and X-ray photoelectron spectroscopy. The effects of process parameters on fibre morphology was studied by scanning electron microscopy and the mechanical properties of the membranes investigated. 26 refs. Beijing,University of Chemical Technology; Peking,University; Tsinghua,University CHINA
Accession no.1008976 Item 177 Journal of Adhesion 83, No.7-9, July-Sept.2007, p.785.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
ROLE OF CHAIN ENTANGLEMENTS IN THE ELECTROSPINNING OF WHEAT PROTEINPOLY(VINYL ALCOHOL) BLENDS Woerdeman D L; Shenoy S; Breger D An investigation was carried out to ascertain whether the rapid solvent removal evaporation occurring during electrospinning enabled gluten protein and PVAl chains to remain at least partially entangled in the solid state. Differential scanning calorimetry was employed to compare the thermal characteristics of electrospun nonwoven fibrous sheets comprising 100% commercial wheat gluten, 100% PVAl and a 75/25 wheat gluten/PVAl blend. The elemental compositions of the individual fibres with those of the spherical domains found in the non-woven fibrous sheets were compared using energy dispersive spectroscopy. Both scanning electron microscopy and energy dispersive spectroscopy revealed that the inorganic constituents existed as spherical, micrometer-sized domains in the final products. 33 refs. Drexel,University; Philip Morris USA USA
Accession no.1008844 Item 178 Journal of Bioactive and Compatible Polymers 22, No.5, Sept.2007, p.508. ELECTROSPUN NANOFIBERS SURFACE MODIFIED WITH FLUORESCENT PROTEINS Choi J S; Yoo H S The fabrication of nanofibres of blends of poly(epsiloncaprolactone) and various proportions of amine-terminated poly(ethylene glycol-b-epsilon-caprolactone) block copolymer by electrospinning, and their characterisation by FESEM and surface amine groups, is described. The effects of blend composition on the immobilisation and release properties of fluorescent-labelled proteins from the swollen nanofibres were investigated by FESEM and confocal laser scanning microscopy and the results are discussed in terms of biocompatibility and potential tissue engineering applications. 38 refs.
in dimethylacetamide and subsequent selective removal of PVP, and their characterisation by SEM (surface morphology), DSC (crystallinity), FTIR and WAXD (crystalline structure), nitrogen adsorption isotherms and mercury porosimetry (porosity), is described. The effects of PVDF/PVP blend ratio on pore and crystal structure of the nanofibres were investigated and the results are discussed. 21 refs. Tokyo,Institute of Technology; Kochi,Women's University; Kanazawa,Institute of Technology JAPAN
Accession no.1008557 Item 180 Journal of Applied Polymer Science 106, No.4, 15th Nov.2007, p.2363. SELECTIVE CHEMICAL ABSORBANCE IN ELECTROSPUN NONWOVENS Chunhui Xiang; Frey M W; Taylor A G; Rebovich M E The absorbance of liquids and dyes with various degrees of hydrophilicity into electrospun fabrics (cellulose and poly(lactic acid) (PLA) with comparable fibre diameters and pore spacings between the fibres) and conventional woven cotton and PETP fabrics was studied. The cotton and PETP fabrics had pore spacings between the fibres which were 10-20 times larger than those of the electrospun fabrics. The absorbance of liquids and dyes with various degrees of water/octanol solubility on to hydrophobic (PETP and PLA) and hydrophobic (cellulose and cotton) fabrics was compared. The dyes used were a direct dye (Rit Scarlet 5), a disperse red dye (005 Spectrasperse Rubine 3BA) and a fluorescent dye (D-820 Savannah Yellow). The decreased fibre size and pore size found in electrospun PLA and cellulose nonwoven fabrics led to increased absorbency. Also, the small fibre size and pitted surface morphology of the PLA electrospun fabrics resulted in greater hydrophobicity than that reported for bulk PLA materials. The affinity for both the dye and the bath liquid affected the absorbance of the dyes from aqueous baths. 17 refs. Cornell University
Kangwon,National University
USA
KOREA
Accession no.1008184
Accession no.1008640 Item 179 Polymer Journal (Japan) 39, No.10, 2007, p.1060. PREPARATION OF POROUS PVDF NANOFIBER FROM PVDF/PVP BLEND BY ELECTROSPRAY DEPOSITION Nasir M; Matsumoto H; Minagawa M; Tanioka A; Danno T; Horibe H The fabrication of poly(vinylidene fluoride)(PVDF) nanofibres with porous structures by electrospray deposition from blends of PVDF and poly(vinyl pyrrolidone)(PVP)
© Copyright 2008 Smithers Rapra Technology
Item 181 Journal of Applied Polymer Science 106, No.4, 15th Nov.2007, p.2177. ELECTROSPUN HYDROXYPROPYL METHYL CELLULOSE PHTHALATE (HPMCP)/ ERYTHROMYCIN FIBERS FOR TARGETED RELEASE IN INTESTINE Meng Wang; Linge Wang; Yong Huang Hydroxypropyl methyl cellulose phthalate (HPMCP)/ erythromycin fibre mats with various diameters were prepared by electrospinning. When the drug was added, the morphology of the fibres changed from a columnar
75
References and Abstracts
to a tape-like shape. No drug was found aggregated on the surface of the erythromycin-containing mats, which indicated that the drug was embodied or encapsulated inside the fibres. Because HPMCP is pH-sensitive, erythromycin was released from the fibre mats by a slow diffusion process in artificial gastric juice, whereas in artificial intestinal juice with a pH higher than that of the artificial gastric juice, it was released in nearly first-order kinetics because of the first-order kinetics dissolution of the HPMCP fibres in the artificial intestinal juice. The rate of erythromycin release in the artificial intestinal juice was more than 2.5 times faster than that in artificial gastric juice. The rate and the total amount of drug released both in stomach and intestine decreased with increasing average fibre diameter. 30 refs. Chinese Academy of Sciences CHINA
Accession no.1008163 Item 182 Polimeros: Ciencia e Tecnologia 17, No.3, July-Sept. 2007, p.206. CHARACTERIZATION OF AN ELECTROSPINNING PROCESS USING DIFFERENT PAN/DMF CONCENTRATIONS Gomes D S; Da Silva A N R; Morimoto N I; Mendes L T F; Furlan R; Ramos I An electrospinning process for the production of fibres for use in nanosensor applications was extensively investigated using precursor solutions with different concentrations of PAN diluted in a fixed amount of dimethyl formamide. The effects of solution viscosity, applied voltage and distance between the needle tip and collector plate on fibre properties, including fibre diameter, fibre shape, fibre length and morphology, were examined and the behaviour of the electrical current, monitored during the deposition process, correlated with fibre characteristics. 17 refs. EPUSP; FATEC; Puerto Rico,University BRAZIL
Accession no.1008119 Item 183 Journal of Applied Polymer Science 107, No.2, 15th Jan.2008 p.909. PREPARATION OF POLY(ETHER SULFONE) NANOFIBERS BY GAS-JET/ ELECTROSPINNING Yi Lin; Yongyi Yao; Xiaozhan Yang; Na Wei; Xuqing Li; Ping Gong; Ruixi Li; Dacheng Wu Synthesis of polyethersulphone nanofibres from dimethylformamide solution by gas jet electrospinning is described and discussed. Parameters such as solution concentration, applied voltage, tip to collector distance, gas flow rate and needle inner diameter were varied and
76
the effects of these on fibre diameter and properties was determined. Reducing solution concentration resulted in reduced fibre diameter, but mixed bead fibres were easily formed. Optimum spinning conditions were determined and described, and fibres were characterised using scanning electron microscopy. 45 refs. Sichuan,University CHINA
Accession no.1007877 Item 184 Macromolecular Rapid Communications 28, No.22, 16th Nov.2007, pp. 2159. POLYMORPHISM CONTROL OF POLY(VINYLIDENE FLUORIDE) THROUGH ELECTROSPINNING Zheng J; He A; Li J; Han C C The polymorphism of poly(vinylidene difluoride) (PVDF) was controlled by electrospinning. Fibrous membranes of PVDF with a fibre diameter in the range from 100 nm to several micrometers were prepared by electrospinning, which permitted a simultaneous adjustment of the crystal phase of the electrospun PVDF fibres. PVDF fibrous membranes containing mainly alpha-, beta- or gamma-phase PVDF could be produced successfully by selecting the electrospinning parameters, such as the solvent, temperature, feeding rate, and tip-to-collector distance. 17 refs. Beijing,Chinese Academy of Sciences CHINA
Accession no.1007728 Item 185 Polymer 48, No.22, 2007, p.6617. NEW SOLVENT FOR POLYAMIDES AND ITS APPLICATION TO THE ELECTROSPINNING OF POLYAMIDES 11 AND 12 Behler K; Havel M; Gogotsi Y Polyamides with long hydrocarbon chains, e.g. PA11 and PA12, are generally dissolved in phenolic or fluoric solvents that prevent these polymers from being electrospun and used in many applications because of their high boiling point and/or prohibitive cost. We demonstrate that a mixture of formic acid and dichloromethane can lead to the dissolution of various polyamides enabling their subsequent electrospinning. Nanofibres and nanoribbons of 130 nm and greater in average diameter were obtained and characterised using scanning electron microscopy and Raman spectroscopy. 23 refs. Drexel,University USA
Accession no.1007446
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 186 Polymers in Defence and Aerospace Applications. Proceedings of an international conference held Toulouse, France, 18th-19th September 2007. Shawbury, Smithers Rapra Technology Ltd., 2007, Paper 7, pp.10, ISBN 9781847350190, 29 cm, 012 CONDUCTING POLYMER NANOFIBERS OBTAINED BY ELECTROSPINNING Robitaille L; Laforgue A Non-woven mats of poly(3-hexylthiophene) fibres with diameters down to 500 nm were produced by electrospinning of poly(3-hexylthiophene) solutions containing a small amount of a high molec.wt. PEO. The morphology of the nanofibres was investigated by scanning electron microscopy and the electrical conductivity of the nanofibres was determined after iodine vapour doping for at least 48 hours. The structure/ properties relationships were assessed as a function of processing parameters and ratio of conducting and spinnable polymers. 36 refs. Canada,National Research Council (Smithers Rapra Technology Ltd.) CANADA
Accession no.1007156 Item 187 Macromolecular Rapid Communications 28, No.21, 1st Nov.2007, p.2062. PHOTOCROSSLINKABLE LIQUID CRYSTAL MAIN-CHAIN POLYMERS. THIN FILMS AND ELECTROSPINNING Krause S; Dersch R; Wendorff J H; Finkelmann H Details are given of a method of preparing thin films and aligned fibres of main-chain liquid crystalline oxybenzoic acid chloride polymers for use in mechanical actuators. Polymer mechanical properties were investigated and data for temperature-dependent changes in length and nonlinear stress-strain relationships are presented. Electrospinning was used to obtain fibres from solution with in situ UV curing. 21 refs. Freiburg,Albert-Ludwigs University; Marburg,Philipps University EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1007073 Item 188 Journal of Applied Polymer Science 106, No.5, 5th Dec.2007, p.3282. EFFECTS OF THE TACTICITIES OF POLYVINYL ALCOHOL ON THE STRUCTURE AND MORPHOLOGY OF POLYVINYL ALCOHOL NANOWEBS PREPARED BY ELECTROSPINNING Lim H J; Lee S J; Bae H J; Noh S K; Lee Y R; Han S S; Jeon H Y; Park W H; Lyoo W S
© Copyright 2008 Smithers Rapra Technology
The effects of tacticities on the characteristics of PVAL nanowebs prepared by an electrospinning technique were investigated. The influence of changing initial polymer concentration, applied voltage and tip-to-collector distance on the formation of PVAL webs with uniform nanofibres is discussed. Characterisation was undertaken using SEM, proton NMR, DSC and X-ray diffraction. 38 refs. Yeungnam,University; Daegu,Gyeongbuk Institute of Science and Technology; KOREA
Accession no.1007035 Item 189 Journal of Applied Polymer Science 106, No.5, 5th Dec.2007, p.3171. MULTIJET ELECTROSPINNING OF CONDUCTING NANOFIBERS FROM MICROFLUIDIC MANIFOLDS Srivastava Y; Marquez M; Thorsen T Details are given of a method for the electrospinning of conducting polymeric composite nanofibres using a PDMS-based microfluidic device. Nanofibres of polyvinyl pyrrolidone and its composite with polypyrrole were prepared using one-step and two-step microfluidic electrospinning. The effect of processing variables on the morphology of the nanofibres using this device were also studied. Morphologies were examined using SEM. 42 refs. MIT; INEST Group; Arizona,State University; NIST USA
Accession no.1007022 Item 190 Molecular Crystals and Liquid Crystals 472, 2007 p.571. ELECTROSPINNING OF POLYCARBONATE/ TETRAPYRAZINOINDOLOPORPHYRAZINE COMPOSITE FIBERS Il Woong Baek; Jae Yun Jaung; Seong Hun Kim; Heejoon Ahn Electrospinning was used to prepare composite fibres of a polycarbonate and tetrapyrazinoindoloporphyrazine to determine whether the optical and electronic properties of the filler were retained after processing with a polymer. X-ray photoelectron spectroscopy, ultraviolet visible spectroscopy and scanning electron microscopy were used in the analysis, and it was confirmed that properties of the filler were very largely retained. Two different solvents were used in electrospinning, chloroform and cyclohexanone, with differences observed in fibre morphology observed in each case. 21 refs. Hanyang,University KOREA
Accession no.1006970
77
References and Abstracts
Item 191 E-Polymers No.133, 2007 p.1. PREPARATION AND CHARACTERIZATION OF PVA/BORON POLYMER PRODUCED BY AN ELECTROSPINNING TECHNIQUE Uslu I; Dastan H; Altas A; Yayli A; Atakol O; Aksu M L
Electrospinning of a silk fibroin to prepare a three dimensional scaffold was described, and the structures were characterised using scanning electron microscopy. Scaffolds were evaluated for cell adhesion using mouse fibroblast cells. The scaffold was shown to be similar to a natural extracellular matrix, and would be expected to perform similarly with the porous structure allowing cell growth within the scaffold structure. 24 refs.
Crosslinking of polyvinyl alcohol (PVAl) by boron, using different blend concentrations of PVAl and boric acid, and electrospinning resulted in PVAl/boron blend fibres of different diameters from 0.3 to 4 micron. Fibres were characterised using Fourier transform infrared spectroscopy, scanning electron microscopy, electrical conductivity and differential scanning calorimetry. Fibre thermal stability increased with boron addition, as did fibre diameter compared to spinning of PVAl under similar conditions. Boron oxide and the formation of boron-oxygen-carbon bonds were identified in the structure of the electrospun fibres. 9 refs. Selcuk,University; Turkish Atomic Energy Authority; Ankara,University; Gazi,University
Seoul,National University; Yonsei,University
TURKEY
Accession no.1006932 Item 192 Macromolecules 40, No.21, 16th Oct.2007 p.7689. EXPERIMENTAL AND THEORETICAL INVESTIGATIONS OF POROUS STRUCTURE FORMATION IN ELECTROSPUN FIBERS Dayal P; Jing Liu; Kumar S; Thein Kyu Electrospinning of amorphous polymers, such as polymethyl methacrylate from methylene chloride solution, or polystyrene from tetrahydrofuran, can result in fibres with a porous structure. Development of this porous structure was studied using scanning electron microscopy, and by theoretical modelling treating polymers as beads connected by Maxwell elements in a cylindrical coordinate system. The simulation method revealed real time formation of pores along the spinning direction forming as changes take place in solution concentration during electrospinning. Experimental and theoretical results were compared. 37 refs. Akron,University; Georgia,Institute of Technology USA
Accession no.1006915 Item 193 Journal of Applied Polymer Science 106, No.6, 15th Dec.2007, p.3922. ELECTROSPUN THREE-DIMENSIONAL SILK FIBROIN NANOFIBROUS SCAFFOLD Chang Seok Ki; Jong Wook Kim; Jin Ho Hyun; Ki Hoon Lee; Hattori M; Dong Kyun Rah; Young Hwan Park
78
KOREA
Accession no.1006834 Item 194 Journal of Applied Polymer Science 106, No.6, 15th Dec.2007 p.3648. ALIGNMENT OF ELECTROSPUN POLYSTYRENE WITH AN ELECTRIC FIELD Chanunpanich N; Hongsik Byun Alignment of polystyrene fibres in an electrospun polystyrene mat, and the conditions for achieving this, was investigated and described. A solution concentration of 20 percent polystyrene in a 75/25 solvent mixture of tetrahydrofuran and dimethylformamide was used for electrospinning, and use of a voltage stabiliser assisted in fibre alignment. Fibres and fibre alignment was examined using scanning electron microscopy. 31 refs. King Mongkut's Institute Of Technology North Bangkok; Keimyung,University KOREA; THAILAND
Accession no.1006801 Item 195 Journal of Bioactive and Compatible Polymers 22, No.4, July 2007, p.379. COMPOSITION-GRADED FILMS OF FLUOROAPATITE/PHB FABRICATED VIA ELECTROSPINNING FOR TISSUE ENGINEERING Zhao D M; Wang Y X; Xu R W; Wu G; Zhang L Q; Yu D S; Cui F Z; Chen D F; Tian W The fabrication of gradient composition films of fluoroapatite and poly(3-hydroxybutyrate-co-4hydroxybutyrate) via electrospinning from solutions of the components, and their characterisation by SEM (surface morphology), XRD, DSC (thermal properties), tensile testing (mechanical properties) and cell culture (biocompatibility), is described. The results are discussed in terms of potential applications as scaffold materials for tissue engineering. 30 refs. Beijing,University of Chemical Technology; Tsing Hua,University; Beijing,Research Institute of Traumatology and Orthopaedics CHINA
Accession no.1006769
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 196 Journal of the Textile Institute 98, No.3, 2007, p.237. MANIPULATION OF THE ELECTRIC FIELD OF ELECTROSPINNING SYSTEM TO PRODUCE POLYACRYLONITRILE NANOFIBER YARN Dabirian F; Hosseini Y; Hosseini Ravandi S A The fabrication of twisted uniaxially aligned polyacrylonitrile nanofibre yarn by electrospinning from a solution of the polymer in dimethylformamide, using a negatively charged bar in the electric field to form an electrostatic multipolar field, is described. The yarns were characterised by SEM (diameter and morphology), XRD (crystallinity) and mechanical properties, and the results are discussed in comparison with those for yarns produced by conventional electrospinning. 14 refs. Isfahan,University of Technology; Tehran,Sharif University of Technology IRAN
Accession no.1006749 Item 197 Macromolecules 40, No.22, 30th Oct.2007, p.7973. ELECTROSPINNING OF POLYACRYLONITRILE SOLUTIONS AT ELEVATED TEMPERATURES Chi Wang; Huan-Sheng Chien; Chia-Hung Hsu; Yin-Chi Wang; Cheng-Ting Wang; Hsin-An Lu The effects of needle diameter, solution properties and processing variables on electrospun polyacrylonitrile (PAN) fibres are systematically investigated. Decreasing PAN concentration and/or increasing solution temperature result in a progressive reduction in fibre diameter. The dominant processing variable in determining the fibre diameter is the applied electric field. Results suggest that high temperature electrospinning is an effective approach to significantly reducing fibre diameter through solution property manipulation. High temperature electrospinning is shown to be an effective approach in producing ultrathin PAN fibres with a diameter lower than 100 nm. 50 refs.
scanning electron microscopy, TEM and X-ray diffraction. The nanotubes were aggregated heavily in the fibres obtained by traditional electrospinning while nanotubes were well distributed and aligned in the PAN fibres produced by vibration-electrospinning. 19 refs. Donghua,University CHINA
Accession no.1005983 Item 199 Polymer International 56, No.11, Nov.2007, p.1361. APPARATUS FOR PREPARING ELECTROSPUN NANOFIBERS: DESIGNING AN ELECTROSPINNING PROCESS FOR NANOFIBER FABRICATION SuA Park; Koeun Park; Hyeon Yoon; JoonGon Son; Teijin Min; GeunHyung Kim A review is presented on how interactions between processing conditions and electrical and rheological properties of electrospun nanofibres can be controlled using a range of nozzle types, target electrodes and guiding electrodes. 48 refs. Korea,Institute of Machinery & Materials KOREA
Accession no.1005982 Item 200 Polymer International 56, No.11, Nov.2007, p.1349. EXTRACELLULAR MATRIX REGENERATED:TISSUE ENGINEERING VIA ELECTROSPUN BIOMIMETIC NANOFIBERS Sell S; Barnes C; Smith M; McClure M; Madurantakam P; Grant J; McManus M; Bowlin G A review is presented on the role of electrospinning in the engineering of various tissues and applications (skin/ wound healing, cartilage, bone, vascular tissue, urological tissue, nerve and ligament). Its potential role in the future is also considered. 125 refs. Virginia,Commonwealth University
National Cheng Kung University
USA
TAIWAN
Accession no.1005981
Accession no.1006519 Item 198 Polymer International 56, No.11, Nov.2007, p.1367. CARBON NANOTUBE-REINFORCED POLYACRYLONITRILE NANOFIBERS BY VIBRATION-ELECTROSPINNING Yu-Qin Wan; Ji-Huan He; Jian-Yong Yu Polyacrylonitrile/multiwalled carbon nanotube fibres were electrospun by traditional electrospinning and vibrationelectrospinning and characterised by FTIR spectroscopy,
© Copyright 2008 Smithers Rapra Technology
Item 201 Polymer International 56, No.11, Nov.2007, p.1340. ENGINEERING ELECTROSPUN NANOFIBRILLAR SURFACES FOR SPINAL CORD REPAIR: A DISCUSSION Meiners S; Ahmed I; Ponery A S; Amor N; Harris S L; Ayres V; Yuan Fan; Qian Chen; Delgado-Rivera R; Babu AN An investigation was carried out to ascertain whether unmodified or peptide-modified polyamide nanofibres
79
References and Abstracts
incorporated into an over-hemisection spinal cord model would allow axonal regrowth in-vivo following central nervous system injury. The nanofibres were visualised using atomic force microscopy and their biocompatibility assessed. The unmodified nanofibres supported modest axonal regeneration in the injured spinal cord whereas the modified nanofibres enhanced the ability of the nanofibres to facilitate axonal regrowth. However, random orientation of the fabric folds impeded the forward movement of axons. 41 refs. New Jersey,University of Medicine and Dentistry; Michigan,State University; Rutgers,University USA
Accession no.1005980 Item 202 Polymer International 56, No.11, Nov.2007, p.1330. SOME FASCINATING PHENOMENA IN ELECTROSPINNING PROCESSES AND APPLICATIONS OF ELECTROSPUN NANOFIBERS Songting Tan; Xianwei Huang; Bolin Wu Some fascinating phenomena associated with the remarkable features of nanofibres in electrospinning processes are briefly reviewed under the headings of jet instability in the electrospinning process, control of chemical composition, modification of electrospun nanofibres, control of secondary structures, alignment of electrospun nanofibres, multi-jet electrospinning, branching and electrode polarity. Progress being made in applications, including filtration applications, electrical applications, optical applications, sensors and biomedical applications, of electrospun nanofibres is also covered. 117 refs. Xiangtan University CHINA
Accession no.1005979 Item 203 Polymer International 56, No.11, Nov.2007, p.1323. MATHEMATICAL MODELS FOR CONTINUOUS ELECTROSPUN NANOFIBERS AND ELECTROSPUN NANOPOROUS MICROSPHERES Ji-Huan He; Lan Xu; Yue Wu; Yong Liu A brief review of mathematical models for electrospinning and their applications is presented. Sections are included on the one-dimensional model, Spivak-Dzenis Model, Wan-Guo-Pan model, allometric model, electrospinnability and vibration electrospinning, electrospinning dilation and electrospun nanoporous microspheres, the nano-effect in electrospinning, spider-spun fibre and Siro-spinning and the E-infinity theory, a potential theory for dealing with quantumlike properties and nano-effect on the nanoscale. 72 refs.
80
Donghua,University CHINA
Accession no.1005978 Item 204 AATCC Review 7, No.3, March 2007, p.40. PRODUCTION AND SELECTED PROPERTIES OF ELECTROSPUN POLY(ETHYLENE TEREPHTHALATE) NANOFIBRES Phaneuf M D; Bide M J; Bachuwar A; Mignanelli M; Brown P J Polyethylene terephthalate nanofibres were prepared by electrospinning from solution using unmodified PETP and PETP modified with ethylenediamine. Several polymeric additives, including cellulose acetate, PEO and polyethylene glycol, were also added to the spinning solution. The nanofibres obtained were structurally characterised by scanning electron microscopy and their tensile strengths, elongation at break and dye uptake behaviour investigated. The results obtained indicated that the nanofibres were potentially suitable for the manufacture of topical and/or implantable medical devices. 15 refs. BioSurfaces; Rhode Island,University; Clemson,University USA
Accession no.1005927 Item 205 Polymer Preprints. Volume 46. Number 2. August 2005. Papers are presented at the ACS meeting held Washington, D.C., August 2005. Washington, D.C., ACS, Div. of Polymer Chemistry, 2005, p.599-600, CD-ROM, 012 ELECTROSPINNING NANOFIBER MEMBRANES OF POLY(BIS(TRIFLUOROETHOXY) PHOSPHAZENE) Singh A; Steely L; Allcock H R The fabrication of highly hydrophobic nanostructured fibrous mats of poly(bis(trifluoro ethoxy)phosphazene) via electrospinning is reported. The dimensions of the polymer fibres are varied from 80 nm to 1.4 micrometres by altering the electrospinning conditions. The surface properties of these mats are characterised by water contact angle and XPS measurements. 10 refs. Pennsylvania,State University (ACS,Div.of Polymer Chemistry) USA
Accession no.1005564 Item 206 Polymer 48, No.21, 2007, p.6384.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
REDUCING ELECTROSPUN NANOFIBER DIAMETER AND VARIABILITY USING CATIONIC AMPHIPHILES Lin K; Kian-Ngiap Chua; Christopherson G T; Lim S; Hai-Quan Mao
study shows that electrospinning is a promising technology for the production of high performance nanoparticle filters. 32 refs. Hiroshima,University; St.Louis,Washington University; Japan Vilene Co.Ltd.
One major limitation of the electrospinning technique for generating polymer fibres is the large average diameter and the broad diameter variability of electrospun fibres. Improved methods of controlling fibre diameter and variability will have implications for many applications ranging from filtration to cell and tissue engineering. Here we report an effective method of reducing the diameter and variability of fibres prepared from three different polymers, poly(ethersulphone), poly(caprolactone), and poly(caprolactone-co-ethyl ethylene phosphoester), by doping polymer solutions with a positively charged amphiphile, octadecyl rhodamine (R18) or octadecyltrimethylammonium bromide (OTAB) at 5000:1 to 20:1 of polymer to amphiphile weight ratio. This is due to the combined effect of field-driven surface partitioning of positively charged amphiphiles and surface tension reduction. This method of diameter reduction can be applied easily without modifying the electrospinning setup or changing the polymer-solvent system. 34 refs. Johns Hopkins University; Singapore,National University
JAPAN; USA
SINGAPORE; USA
Accession no.1005466 Item 207 Chemical Engineering Science 62, No.17, 2007, p.4751. NANOPARTICLE FILTRATION BY ELECTROSPUN POLYMER FIBERS Yun K M; Hogan C J; Matsubayashi Y; Kawabe M; Iskandar F; Okuyama K Polyacrylonitrile (PAN) fibres with mean diameters in 270400 nm range were prepared by electrospinning for use as a filter media. Compared to commercial filters made of polyolefin and glass, the fibres of electrospun filters were more uniform in diameter. The performance of electrospun filters was evaluated by measuring the penetration of monodisperse NaCl nanoparticles (below 80 nm in size) through the filters. It was found that electrospun filters could be made which had nanoparticle penetration values comparable to commercial filters but with substantially less filter mass. The penetration of nanoparticles through the electrospun filter media could be reduced by increasing the filter thickness, which is controlled by the collection time during the electrospinning process. Nanoparticle collection by electrostatic forces was found to be negligible for electrospun filters. Filter quality factors and single fibre collection efficiencies were found to be independent of filter thickness for electrospun filters, and the penetration of nanoparticles through electrospun filters was in better agreement with theoretical predictions than was the measured penetration through a commercial filter. This
© Copyright 2008 Smithers Rapra Technology
Accession no.1005422 Item 208 Polymer Preprints. Volume 46. Number 2. August 2005. Papers presented at the ACS meeting held Washington, D.C., August 2005. Washington, D.C., ACS,Div.of Polymer Chemistry, 2005, p.880-881, CD-ROM, 012 ELECTROSPUN POLY(L-LACTIC ACIDCO-SUCCINIC ACID-CO-1,4-BUTANE DIOL) FIBROUS MEMBRANES Hun Sik Kim; Hyoung-Joon Jin; Jin San Yoon Synthesis of fibrous membranes consisting of a copolymer of lactic acid, succinic acid and butane diol (PLASB) by electrospinning is described. Membranes were characterised by nuclear magnetic resonance spectroscopy, gel permeation chromatography, differential scanning calorimetry, tensile measurements and field emission scanning electron microscopy. PLASB was prepared by direct condensation polymerisation. Membrane properties indicated potential use as a tissue substitute. 8 refs. Inha,University (ACS,Div.of Polymer Chemistry) KOREA
Accession no.1005059 Item 209 Polymer Preprints. Volume 46. Number 2. August 2005. Papers presented at the ACS meeting held Washington, D.C., August 2005. Washington, D.C., ACS,Div.of Polymer Chemistry, 2005, p.736-737, CD-ROM, 012 ELECTROSPUN NANOFIBER OF MULTIWALLED CARBON NANOTUBE AND POLY(METHYL METHACRYLATE) COMPOSITES Hyun Suk Kim; Jun Hee Sung; Hyoung Jin Choi; In-Joo Chin; Hyoung-Joon Jin Multi-walled carbon nanotubes were incorporated into polymethyl methacrylate using an in-situ bulk polymerisation method and the resulting nanocomposite was electrospun to produce nanofibres with embedded and aligned nanotubes. Composites were characterised using field emission scanning electron microscopy, transmission electron microscopy and electrical conductivity measurements. 14 refs. Inha,University (ACS,Div.of Polymer Chemistry) KOREA
Accession no.1005006
81
References and Abstracts
Item 210 Polymer Engineering and Science 47, No.10, 2007, p.1530. HOW IS IT POSSIBLE TO PRODUCE HIGHLY ORIENTED YARNS OF ELECTROSPUN FIBERS? Moon S; Farris R J Electrospinning of polymeric nanofibres onto a stationary grounded target produces a nonwoven mat-like material. Using a rapidly rotating grounded target in the form of a wheel or belt, it is possible to produce significant lengths of highly oriented yarns of electrospun filaments. This observation is difficult to explain when one compares the calculated velocity of an electrospun monofilament with the surface velocity of the grounded target. This study was undertaken to attempt to answer this question. Are the calculated fibre velocities correct. Is the collected electrospun filament really a monofilament. Does the electrospun filament split into multiple filaments or do fibres loop in an oriented manner on the collection wheel. 3 refs. Massachusetts,University USA
Accession no.1004775 Item 211 Advanced Materials 19, No.18, 17th Sept.2007, pp. 2480. NOVEL BIOHYBRID MATERIALS BY ELECTROSPINNING: NANOFIBERS OF POLY(ETHYLENE OXIDE) AND LIVING BACTERIA Gensheimer M; Becker M; Brandis-Heep A; Wendorff J H; Thauer R K; Greiner A Fibres of poly(ethylene oxide) (PEO) containing living bacteria were prepared by electrospinning from aqueous dispersions of Escherichia coli or Micrococcus luteus bacteria with PEO. Whereas E. coli and M. luteus bacteria survived the electrospin-ning process, E. coli did not survive dry storage in nonwoven PEO fabric at 20 deg.C for more than 1 h. In contrast, M. luteus survived at least 250 h of dry storage at 20 deg.C in electrospun PEO nonwoven fabrics. 20 refs. Marburg,Philipps University; Marburg,Max Planck Institute for Terrestrial Microbiology EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1004692 Item 212 Polymer 48, No.19, 2007, p.5742. EFFECT OF EVAPORATION AND SOLIDIFICATION OF THE CHARGED JET IN ELECTROSPINNING OF POLY(ETHYLENE OXIDE) AQUEOUS SOLUTION Tripatanasuwan S; Zhenxin Zhong; Reneker D H
82
The electrospinning process uses electrical force to produce nanofibres. A charged droplet acquires a conical shape known as the Taylor cone and then becomes unstable. A charged jet emerges from the vertex and develops a spiral path due to the electrically driven bending instability, which makes it possible, in a small space, for the jet to elongate by a large amount and produce nanofibres. Evaporation and the associated solidification are identified as important factors that affect the diameter of electrospun nanofibres. In this study, the evaporation rate and solidification of the charged jet are controlled by varying the relative humidity during electrospinning of poly(ethylene oxide) from aqueous solution. As the relative humidity increases, the solidification process becomes slower, allowing elongation of the charged jet to continue longer and thereby to form thinner fibres. As the relative humidity increases from 5.1% to 48.7%, the diameter of the solidified fibre decreases from 253nm to 144nm. As the relative humidity increases above 50%, beads formed on the thinner fibres, indicating that the capillary instability occurs before the jet solidified. The vapour concentration of solvent is an effective electrospinning process control parameter of fibre diameter that also produces a systematic change in the development of beads on the fibres.18 refs. Akron,University USA
Accession no.1004497 Item 213 Journal of Power Sources 172, No.2, 2007, p.863. ELECTROSPUN POLYMER MEMBRANE ACTIVATED WITH ROOM TEMPERATURE IONIC LIQUID: NOVEL POLYMER ELECTROLYTES FOR LITHIUM BATTERIES Cheruvally G; Kim J K; Choi J W; Ahn J H; Shin Y J; Manuel J; Raghavan P; Kim K W; Ahn H J; Choi D S; Song C E A new class of polymer electrolytes (PEs) based on an electrospun polymer membrane incorporating a roomtemperature ionic liquid (RTIL) has been prepared and evaluated for suitability in lithium cells. The electrospun poly(vinylidene fluoride-co-hexafluoropropylene) P(VdF-HFP) membrane is activated with a 0.5M solution of LiTFSI in 1-butyl-3-methylimidazolium bis(trifluoromethanesulphonyl)imide (BMITFSI) or a 0.5M solution of LiBF4 in 1-butyl-3-methylimidazolium tetrafluoroborate (BMIBF4). The resulting PEs have an ionic conductivity of 2.3x10-3 Scm-1 at 25 deg.C and anodic stability at greater than 4.5V versus Li+/Li, making them suitable for practical applications in lithium cells. A Li/ LiFePO4 cell with a PE based on BMITFSI delivers high discharge capacities when evaluated at 25 deg.C at the 0.1C rate (149mAhg-1) and the 0.5C rate (132mAhg-1). A very stable cycle performance is also exhibited at these low current densities. The properties decrease at the
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
higher, 1C rate, when operated at 25 deg.C. Nevertheless, improved properties are obtained at a moderately elevated temperature of operation, i.e. 40 deg.C. This is attributed to enhanced conductivity of the electrolyte and faster reaction kinetics at higher temperatures. At 40 deg.C, a reversible capacity of 140mAhg-1 is obtained at the 1C rate. 32 refs.
as jet radius and fluid velocity in the region of the Taylor cone and stable portion of the electrospinning jet and the assumptions underlying electrohydrodynamic models of steady electrospinning jets validated. 22 refs. Delaware,University (SAMPE)
Gyeongsang,National University; Sung Kyun Kwan University
Accession no.1003997
KOREA
Item 216 SAMPE '07: M&P - Coast to Coast and Around the World. Volume 52. Proceedings of a conference held Baltimore, Md., 3rd-7th June, 2007. Covina, Ca., SAMPE International Business Office, 2007, Paper 69, pp.11, CD-ROM. 012 ELECTROSPINNING OF NANOFABRICS Lingaiah S; Shivakumar K N; Sadler R; Sharpe M
Accession no.1004398 Item 214 Polymer Journal (Japan) 39, No.8, 2007, p.878. CORRELATION OF MORPHOLOGY OF ELECTROSPUN FIBERS WITH RHEOLOGY OF LINEAR POLYACRYLAMIDE SOLUTION Vetcher A A; Gearheart R; Morozov V N The morphology of nanofibres produced by electrospinning aqueous solutions of linear polyacrylamides having different molec.wts. was investigated over a broad range of concentrations and the relationship between specific viscosity and morphology of the nanofibres examined. Atomic force microscopy and optical microscopy revealed that electrospinning generated uniform fibres when the polyacrylamide concentration exceeded the entanglement concentration and that the average diameter of the fibres was independent of molec.wt. but proportional to (C/ entanglement concentration). 33 refs. Manassas,George Mason University; Russian Academy of Sciences; Pushchino,Institute of Theoretical & Experimental Biophysics RUSSIA; USA
Accession no.1004130 Item 215 SAMPE '07: M&P - Coast to Coast and Around the World. Volume 52. Proceedings of a conference held Baltimore, Md., 3rd-7th June, 2007. Covina, Ca., SAMPE International Business Office, 2007, Paper 71, pp.14, CD-ROM. 012 KINEMATIC STUDIES OF POLYMER ELECTROSPINNING USING IN SITU MEASUREMENTS Helgeson M E; Grammatikos K N; Deitzel J M; Wagner N J Aqueous solutions of PEO seeded with colloidal PU particles were electrospun under various operating conditions and recorded using a CCD camera at frame rates of 2000 fps. The kinematics of the electrospinning jets were investigated using particle tracking velocimetry and high-speed videography and the electrospun fibres and tracer particles imaged by means of field emission scanning electron microscopy. The in-situ measurements were utilised to directly determine internal variables, such
© Copyright 2008 Smithers Rapra Technology
USA
Polyacrylonitrile, polybenzimidazole and polyamide-6,6 based nanofabrics were produced by electrospinning in various solvents on stationary and rotating target collectors and characterised by scanning electron microscopy. The mechanical properties of the electrospun polyamide-6,6 fabrics were tested in tension at room temperature and the char yield of the PAN fibres determined. 24 refs. North Carolina,A & Tech.State Univ. (SAMPE) USA
Accession no.1003995 Item 217 SAMPE '07: M&P - Coast to Coast and Around the World. Volume 52. Proceedings of a conference held Baltimore, Md., 3rd-7th June, 2007. Covina, Ca., SAMPE International Business Office, 2007, Paper 68, pp.13, CD-ROM. 012 PROCESSING OF BIOCIDAL ELECTROSPUN NANOFIBERS Deitzel J; Sun Z; Herson D; Veleva A; Lamba N Nanofibre textiles were produced by electrospinning of different types of PU functionalised to varying degrees with quaternary ammonium compound-based biocidal moieties grafted to the PU backbone. The morphology of the electrospun materials was characterised by scanning electron microscopy and energy dispersive X-ray analysis and the influence of the functionalised moieties on the processing variables, such as solution conductivity, viscosity and polymer/solvent interactions, and the resultant effects on fibre morphology investigated. The antimicrobial properties of the electrospun nanofibres were also investigated and compared with those of solution cast films. 11 refs. Delaware,University; North Carolina,State University; CCL Biomedical Inc. (SAMPE) USA
Accession no.1003994
83
References and Abstracts
Item 218 SAMPE '07: M&P - Coast to Coast and Around the World. Volume 52. Proceedings of a conference held Baltimore, Md., 3rd-7th June, 2007. Covina, Ca., SAMPE International Business Office, 2007, Paper 67, pp.12, CD-ROM. 012 ELECTROSPUN NANOFIBER REINFORCEMENT OF TRANSPARENT POLYMER MATERIALS Zaicheng Sun; Deitzel J M; Krauthauser C; O'Brien D J The scale up of electrospun PU (Estane 4714) nanofibre production using multiple jets and production of transparent PMMA composites from the elastomeric nanofibres are described. The morphology of the composites is characterised by scanning electron microscopy and TEM and the mechanical and optical properties of the composites are determined. The composites exhibit a high degree of transparency below fibre volume fractions of 11% and enhanced toughness through the mechanism of crack arrest. 12 refs. Delaware,University; US,Army Research Laboratory (SAMPE) USA
Accession no.1003993 Item 219 Journal of Applied Polymer Science 106, No.2, 15th Oct2007, p.1337. PREPARATION OF ATACTIC POLY(VINYL ALCOHOL)/SODIUM ALGINATE BLEND NANOWEBS BY ELECTROSPINNING Lee Y J; Shin D S; Kwon O W; Park W H; Choi H G; Lee Y R; Han S S; Noh S K; Lyoo W S Nanofibres were produced by electrospinning using aqueous solutions containing rigid sodium alginate (SA) blended with flexible atactic poly(vinyl alcohol) (PVAl) in various proportions. Uniform fibres of fine structure were obtained using pure PVAl. The blends gave a mixture of fibres and large beads, the bead content increasing with increasing SA content. The SA content of the fibres was confirmed by the strong absorption band at 1610 cm^-^1 and by the endothermic peak obtained by differential scanning calorimetry. The tensile strength of the spun fibre decreased with increasing SA content. 33 refs. Yeungnam,University; Chungnam,National University KOREA
Accession no.1003721 Item 220 Journal of Applied Polymer Science 106, No.2, 15th Oct2007, p.1208. PREPARATION OF ANTIMICROBIAL POLY(EPSILON-CAPROLACTONE) ELECTROSPUN NANOFIBERS CONTAINING SILVER-LOADED ZIRCONIUM PHOSPHATE NANOPARTICLES
84
Yuan-yuan Duan; Jun Jia; Shao-hai Wang; Wei Yan; Lei Jin; Zhong-yi Wang Zirconium phosphate particles (63.7 nm diameter), containing 3.6% silver, were dispersed in 2,2,2trifluoroethanol, followed by the addition of poly(epsiloncaprolactone), such that the particle content was 1 wt% of the polymer content. Nanofibres, containing uniformly dispersed nanoparticles, were prepared by electrospinning. The fibres exhibited good antimicrobial properties and no fibre staining. Cell proliferation studies confirmed the biocompatibility of the fibres, and they were considered suitable for wound dressing applications. 41 refs. Xian,Fourth Military Medical University; Xian Jiaotong,University CHINA
Accession no.1003705 Item 221 E-Polymers No.105, 2007, p.1. ELECTROSPINNING OF POLYAMIDE 6/ MODIFIED-KERATIN BLENDS Zoccola M; Montarsolo A; Aluigi A; Varesano A; Vineis C; Tonin C The fabrication, by electrospinning from formic acid solutions, of blend nanofibres of polyamide-6 with various proportions of modified keratin derived by chemical-free steam explosion of wool, and their characterisation by SEM, FTIR, DSC, polarised optical microscopy and moisture absorption, is described. The results are discussed in comparison with those for cast films of the blends, and the effects of protein content on filament diameter were also studied. 36 refs. CNR; Torino,Politecnico EUROPEAN COMMUNITY; EUROPEAN UNION; ITALY; WESTERN EUROPE
Accession no.1003672 Item 222 Macromolecular Materials and Engineering 292, No.8, 9th Aug.2007, p.949. MASS RATIO OF CDS/POLY(ETHYLENE OXIDE) CONTROLLED PHOTOLUMINESCENCE OF ONEDIMENSIONAL HYBRID FIBERS BY ELECTROSPINNING Cheng Wang; Eryun Yan; Zhiyao Sun; Zijiang Jiang; Yanbin Tong; Yi Xin; Zonghao Huang One-dimensional high-quality CdS/PEO hybrid nanoparticle-polymer fibres were fabricated by an electrospinning method, followed by self-assembly technologies with co-fed H"2S atmosphere at 60 deg C. Structural and spectral data on the resulting hybrid nanofibres was obtained by field emission SEM, TEM, X-ray photoelectron spectroscopy and X-ray
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
diffractometry. The diameters of CdS/PEO hybrid nanofibres ranged from 90 to 200 nm and the average dimension of CdS nanoparticle within fibres from 4 to 12 nm. An interesting aspect of the CdS/PEO nanofibres shown in photoluminescence spectra and fluorescence images was that the fluorescence peaks of CdS/PEO were shifted with change in the mass ratio of CdS/PEO, and consequently the size and phase of nanocrystal CdS. 40 refs. China,Northeast Normal University; Heilongjiang,University; Daqing,Normal College CHINA
Accession no.1003310 Item 223 Polymer Preprints. Volume 48. Number 1. March 2007. Papers are presented at the ACS meeting held Chicago, Il., 25th-30th March 2007. Washington, D.C., ACS, Division of Polymer Chemistry, 2007, p.215-216, CD-ROM, 012 FORMATION AND MECHANICS OF ELECTROSPUN POLYMER JETS Helgeson M E; Grammatikos K N; Deitzel J M; Wagner N J High speed videography and particle tracking velocimetry measurements of stable electrospinning polymer jets demonstrated the validity of a slender body electrohydrodynamic model in the jet stretching regime. Analysis of the model showed that the transient extensional viscosity of the polymer solution governed the morphology of the electrospun fibres. Results were presented for the electrospinning of aqueous PEO solutions across a wide range of experimental conditions which validated the correlation. 12 refs. Delaware,University (ACS,Div.of Polymer Chemistry) USA
Accession no.1003114 Item 224 Journal of Applied Polymer Science 106, No.1, 5th Oct.2007, p.475. BEAD-TO-FIBER TRANSITION IN ELECTROSPUN POLYSTYRENE Eda G; Shivkumar S The bead-to-fibre morphological transition of electrospun PS was investigated. THF and DMF were used as solvents to examine the effect of solvent properties on the morphological variations. The effect of polymer molecular weight and solvent properties on the morphology of beads and fibres was determined. 34 refs. Worcester,Polytechnic Institute USA
Accession no.1002933
© Copyright 2008 Smithers Rapra Technology
Item 225 Journal of Applied Polymer Science 106, No.1, 5th Oct.2007, p.255. FABRICATION AND ELECTRICAL CHARACTERIZATION OF ELECTROSPUN POLYACRYLONITRILE-DERIVED CARBON NANOFIBERS Agend F; Naderi N; Fareghi-Alamdari R Carbon nanofibres were produced from a polyacrylonitrile/ DMF precursor solution by an electrospinning process and pyrolysis. The morphological structure of the nanofibres was studied using SEM. Thermal properties were studied with TGA. An indirect four-point-probe method was used for the measurement of conductivity of nanofibres mats. 13 refs. Tehran,Malek Ashtar University of Technology; Tehran,University IRAN
Accession no.1002903 Item 226 Macromolecules 40, No.14, 10th July 2007, p.4823. AMPHIPHILIC POLY(VINYL ALCOHOL) HYBRIDS AND ELECTROSPUN NANOFIBERS INCORPORATING POLYHEDRAL OLIGOSILSESQUIOXANE Chul-Ki Kim; Byoung-Suhk Kim; Sheikh F A; Un-Soo Lee; Myung-Seob Khil; Hak-Yong Kim Hybrids of polyvinyl alcohol (PVAl) linked with a urethane group between the hydroxyl groups on the PVAl and isocyanate group of a polyhedral oligomeric silsesquioxanes (POSS) were synthesised. Changes to the POSS content affected the degree of hydrophobicity of the hybrid, increasing it with POSS content. Hybrids were characterised using Fourier transform infrared and nuclear magnetic resonance spectroscopies, differential scanning calorimetry, thermogravimetric analysis and wide angle X-ray scattering. Addition of POSS modified the properties of PVAl in both the solid and in solution, and the solid morphology appeared to consist of two crystalline phases. Nanofibres, electrospun from the hybrid and examined using scanning electron microscopy and water absorption, showed enhanced water resistance, with fibres simply swelling rather than dissolving as was found with pure PVAl nanofibres. 33 refs. Chonbuk,National University KOREA
Accession no.1002738 Item 227 Macromolecules 40, No.17, 21st Aug.2007 p.6283. CRYSTALLINE MORPHOLOGY AND POLYMORPHIC PHASE TRANSITIONS IN ELECTROSPUN NYLON-6 NANOFIBERS
85
References and Abstracts
Yi Liu; Li Cui; Fangxiao Guan; Yi Gao; Hedin N E; Lei Zhu; Hao Fong Crystalline morphology and polymorphic phase transitions in electrospun unconfined nylon-6 nanofibres, and nanofibres confined in a polyimide, were studied using Fourier transform infrared spectroscopy, differential scanning calorimetry, and wide angle X-ray scattering. Fibres showed a predominantly metastable gammacrystal form with the crystal axis parallel to the fibre axis. Annealing the fibres converted the crystals from gamma to a stable alpha form with a release of surface tension. In confined fibres the melt recrystallisation and surface tension release was considerable reduced, and Brill transitions were at some 20 degrees centigrade higher than in the unconfined fibre. Complete melting of the nanofibres at temperatures higher than the polymer melting point, and recrystallisation at lower temperatures resulted only in alpha-form crystals. 47 refs. South Dakota,School Of Mines & Technology; Connecticut,University
Yuanxiang Gu; Dairong Chen; Xiuling Jiao Hollow LiNiO"2 fibres were prepared using a capillary spinneret electrospinning technique combined with the solgel method, and the possible mechanism for the fabrication of the hollow fibres was examined. The xerogel fibres and those calcined at different temperatures were characterised by techniques such as TGA, X-ray diffraction, FTIR spectroscopy, TEM and SEM. The addition of polyvinyl pyrrolidone(PVP) to the precursor sol was shown to affect the morphology and microstructure of the hollow LiNiO"2 fibres. The PVP molecules led to the decrease of the liquid surface energy of the LiNiO"2 sol and rapid formation of the rigid skin, which avoided the collapse of the fibres during the surface shrinkage of the fibres and resulted in the formation of the tubular structure of the fibres during the calcination process. 23 refs. Shandong,University CHINA
Accession no.1002274
USA
Accession no.1002703 Item 228 Polymer 48, No.18, 2007, p.5202. ELECTROSPINNING OF THERMOREGULATING ULTRAFINE FIBERS BASED ON POLYETHYLENE GLYCOL/CELLULOSE ACETATE COMPOSITE Chen C; Wang L; Huang Y Ultrafine fibres of polyethylene glycol/cellulose acetate (PEG/ CA) composite in which PEG acts as a model phase change material (PCM) and CA acts as a matrix, were successfully prepared as thermo-regulating fibres via electrospinning. The morphology observation from the electrospun PEG/CA composite fibres revealed that the fibres were cylindrical and had a smooth external surface. PEG was found to be both distributed on the surface and within the core of the fibres. Differential scanning calorimeter (DSC) was used to characterise the thermal properties of the composite fibres. The results indicated that the fibres imparted balanced thermal storage and release properties for their thermo-regulating function and the thermal properties were reproducible after 100 heating-cooling cycles. 32 refs. Guangzhou,Institute of Chemistry; Beijing,Graduate School; Beijing,Institute of Chemistry CHINA
Accession no.1002374 Item 229 Journal of Sol-Gel Science and Technology 43, No.2, Aug.2007, p.245. SYNTHESIS AND CHARACTERIZATION OF HOLLOW LINIO"2 FIBERS VIA SOLELECTROSPINNING METHOD
86
Item 230 Polymer Journal (Japan) 39, No.6, 2007, p.622. ELECTROSPUN GELATIN FIBERS: EFFECT OF SOLVENT SYSTEM ON MORPHOLOGY AND FIBER DIAMETERS Choktaweesap N; Arayanarakul K; Aht-Ong D; Meechaisue C; Supaphol P The electrospinning of gelatin, a naturally-occurring biopolymer, was studied. Gelatin solutions were prepared in either single solvent system, i.e. glacial acetic acid(AA), or mixed solvent system, i.e. AA/2,2,2trifluoroethanol(TFE), AA/DMSO, AA/ethylene glycol(EG), and AA/formamide(F). The electrospinning was carried out under a fixed electrostatic field strength of 7.5 kV/7.5 cm and the polarity of the emitting electrode was positive. The effects of these solvent systems on morphology and/or size of the electrospun materials were observed by SEM. Electrospinning of 15-29% w/v gelatin solutions in AA produced beads, beaded fibres, and smooth fibres, depending on the concentration range. Only smooth fibres were observed in the concentration range of 21-29% w/v, with their average diameter ranging from 214 to 839 nm. The addition of TFE as a co-solvent or another modifying liquid of DMSO, EG or F helped improve the electrospinnability of the resulting gelatin solution. Among the three modifying liquids, DMSO and EG contributed to the formation of smooth gelatin fibres with reduced diameters when compared with those obtained from the solution in pure AA. 31 refs. Chulalongkorn,University; Ramkhamhaeng,University THAILAND
Accession no.1002190
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 231 Journal of Polymer Research 14, No.4, Aug.2007, p.277. IMPROVEMENT OF THE ELECTROSPINNABILITY OF POLYVINYL ALCOHOL VIA DIALYSIS AND COMPLEXATION PRETREATMENT Xinsheng Zhu; Qiang Gao; Detao Xu; Yong Xu An investigation was carried out into the effects of diand tri- valent metal ions and degree of saponification on the electrospinning of aqueous PVAl solutions. The solution properties and microstructure of the PVAl were determined and electrospinnability after dialysis and complexation with ethylene diamine tetraacetic acid examined. Both di- and trivalent metal ions were found to interact with the hydroxyl groups of PVAl, especially at high degrees of saponification, resulting in the formation of intramolecular and intermolecular crosslinks and deterioration in electrospinnability. Complexation altered surface tension, giving rise to enhanced electrospinnability. 8 refs. Soochow,University CHINA
Accession no.1001783 Item 232 Journal of Applied Polymer Science 105, No.6, 15th Sept.2007, p.3618. FABRICATION OF GOLD/PVP NANOFIBER COMPOSITES BY ELECTROSPINNING Wang Y; Li Y; Sun G; Zhang G; Liu H; Du J; Yang S; Bai J; Yang Q Details are given of the dispersion of gold nanoparticles in polyvinyl pyrrolidone nanofibres. Optical properties of gold nanoparticles before and after electrospinning were measured by UV vis spectroscopy. The morphology and distribution of gold nanoparticles in polyvinyl pyrrolidone nanofibres were observed by TEM. The influence of the amount of gold added to and the concentration of polyvinyl pyrrolidone in electrospinning solution over the morphology of the nanofibres were studied. 22 refs. Jilin,University CHINA
Accession no.1001711 Item 233 Journal of Applied Polymer Science 105, No.5, 5th Sept.2007, p.2816. PREPARATION AND ANTIBACTERIAL ACTIVITY OF PET/CHITOSAN NANOFIBROUS MATS USING AN ELECTROSPINNING TECHNIQUE K-H Jung; M-W Huh; W Meng; J Yuan; S H Hyun; J-S Bae; Hudson S M; I-K Kang
© Copyright 2008 Smithers Rapra Technology
Electrospinning of blend solutions of polyethylene terephthalate and chitosan or chitin was used to prepare nanofibre mats with antibacterial activity. Surfaces of the mats were characterised using field emission scanning electron microscopy, electron spectroscopy for chemical analysis, atomic force microscopy and wettability measurements. Fibre diameter was determined, and antibacterial activity against staphylococcus aureus and klebsiella pneumoniae was examined in vitro. Compared to a PET nanofibre control, the blend fibre mats showed improved antibacterial activity with better cell adhesion to the mat. 23 refs. Kyungpook,National University; Kyungil,University; Daegu,University; Raleigh,NC State University KOREA; USA
Accession no.1000736 Item 234 Polymer 48, No.16, 2007, p.4814. TEMPERATURE DEPENDENCE OF POLYMORPHISM IN ELECTROSPUN NANOFIBRES OF PA6 AND PA6/CLAY NANOCOMPOSITE Kim G M; Michler G H; Ania F; Calleja F J B Polymorphism found in nanofibres of polyamide 6 (PA6) and PA6/clay nanocomposite (PA6-NC), prepared by an electrospinning process, was studied by transmission electron microscopy (TEM) and variable-temperature wide angle X-ray scattering (WAXS), and compared with the polymorphic changes occurring in the pre-electrospun bulk materials. TEM results, concerning morphology and dispersion of the nanoclays, reveal that the produced electrospun nanofibres have an average diameter of 50nm, and nanoclays are much more uniformly dispersed in the electrospun PA6-NC fibres than in the pristine PA6NC. According to WAXS measurements, both types of electrospun nanofibres predominantly consist of gammaform crystals of PA6. Upon heating, from room temperature to the melting point, a number of successive transitions are observed for both systems, namely, crystalline gamma to alpha', alpha' to alpha and alpha to the ''amorphous'' deltaform due to breakage of hydrogen bonds. On subsequent cooling, it has been observed, for the first time, that the development of crystalline forms for both systems is quite different from each other. The molten electrospun pure PA6 fibres first crystallize in the high temperature alpha'-form, and then they show the room temperature alpha-form. For these nanofibres, during a temperature cycle of heating and cooling, the initial gamma-form crystals completely turn into the alpha-form crystals as in bulk PA6. In contrast, for the electrospun nanofibres of the PA6-NC, the gamma-form crystals are preserved after completing a thermal cycle down to room temperature. The present findings on the evolution of polymorphism in the electrospun nanofibres of both systems provide useful information regarding their use as reinforcing elements in polymer composites. 54 refs.
87
References and Abstracts
Halle,Martin-Luther-Universitat EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.1000429
the nanotubes the fibre diameter was dramatically reduced compared to spinning the polymer alone. Reasons for this observation were discussed. Nanotubes were seen to be aligned in the fibre direction. 36 refs. North Carolina,State University
Item 235 Polymer 48, No.16, 2007, p.4675. CATALYTIC HYDROLYSIS OF P-NITROPHENYL ACETATE BY ELECTROSPUN POLYACRYLAMIDOXIME NANOFIBERS Chen L; Bromberg L; Hatton T A; Rutledge G C Modification of polyacrylonitrile (PAN) by hydroxylamine resulted in polyacrylamidoxime (PANOx), the oxime groups of which are nucleophilic and capable of hydrolyzing esters. PANOx fibre mats with submicrometer fibre diameters ranging from tens to 300nm were produced by electrospinning a suspension of PANOx blended with PAN (1:1 by weight) in a mixture of N,N-dimethyl formamide (DMF) and dimethyl sulphoxide (DMSO) (85:15 by weight). Catalytic properties of the PANOx nanofibres were tested by the hydrolysis of p-nitrophenyl acetate (PNPA), which mimics toxic organophosphate nerve agents and insecticides. The presence of PANOx fibres significantly accelerated the hydrolysis of PNPA compared to its spontaneous hydrolysis. The rate constants for the hydrolysis (k"1) and the deacetylation (k"2) reactions for the fibres were obtained using a proposed kinetic model. The effect of the fibre size on reaction rate indicated that intra-fibre diffusional resistances might limit the accessibility of the oxime catalytic sites in the fibres and affect their catalytic activity. 42 refs. Massachusetts Institute of Technology USA
Accession no.1000416 Item 236 Journal of Applied Polymer Science 105, No.3, 5th Aug.2007 p.1668. DEVELOPMENT, OPTIMIZATION, AND CHARACTERIZATION OF ELECTROSPUN POLY(LACTIC ACID) NANOFIBERS CONTAINING MULTI-WALLED CARBON NANOTUBES McCullen S D; Stano K L; Stevens D R; Roberts W A; Monteiro-Riviere N A; Clarke L I; Gorga R E Electrospinning of polylactic acid fibre nanocomposites containing multiwalled carbon nanotubes was evaluated to determine optimum spinning parameters, solution strength and nanotube content for development of scaffolds for use in tissue engineering. Scanning and transmission electron microscopies, Fourier transform infrared spectroscopy, current voltage characteristics and tensile measurements were used in the analysis, with statistical analysis package used to evaluate results. Preferred solvent systems and spinning parameters were reported, and in the presence of
88
USA
Accession no.999900 Item 237 Journal of Applied Polymer Science 105, No.3, 5th Aug.2007, p.1351. IN SITU SYNTHESIS OF IRON OXIDE NANOPARTICLES ON POLY(ETHYLENE OXIDE) NANOFIBERS THROUGH AN ELECTROSPINNING PROCESS Sharifi-Sanjani R F M; Sharifi-Sanjani N Electrospinning of an aqueous solution of polyethylene oxide containing ferric chloride and ferrous sulphate in a gaseous ammonia atmosphere resulted in nanofibres coated with iron oxide nanoparticles. Nanofibres were characterised using transmission electron microscopy, differential scanning calorimetry, thermogravimetric analysis and X-ray diffraction. Results were compared to spinning of similar solutions in an air atmosphere and X-ray diffraction peaks indicated that results were different. 25 refs. Tehran,University IRAN
Accession no.999862 Item 238 Journal of Applied Polymer Science 105, No.3, 5th Aug.2007 p.1127. MELT-ELECTROSPINNING OF POLY(ETHYLENE TEREPHTHALATE) AND POLYALIRATE Ogata N; Shimada N; Yamaguchi S; Nakane K; Ogihara T Samples of polyethylene terephthalate of three different intrinsic viscosities and one sample of polyalirate suitable for electrospinning were prepared, and the effects of different electrospinning conditions on the morphology, crystallinity and crystalline orientation of the fibres produced using this process were evaluated. Scanning electron microscopy, differential scanning calorimetry and X-ray diffraction were used in the examination and it was observed that increased laser output power gave a reduction in fibre diameter in all cases. Intrinsic viscosity of the polymer had an effect on fibre diameter, but the minimum average fibre diameter was not affected. Minimum diameter achieved was in the order of 1 micron. 10 refs. Fukui,University JAPAN
Accession no.999836
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Item 239 Rubber Chemistry and Technology 80, No.2, May-June 2007, p.231. FIBER STRUCTURE AND MECHANICAL PROPERTIES OF ELECTROSPUN BUTYL RUBBER WITH DIFFERENT TYPES OF CARBON BLACK Threepopnatkul P; Murphy D; Mead J; Zukas W The fabrication of carbon black-filled butyl rubber non-woven mats as fibrous membranes with controlled porosity and surface area by electrospinning, and their characterisation by SEM, density, solution electrical conductivity and tensile properties is described. The effects of carbon black structure and particle size on morphology and mechanical properties of the products were investigated and the results are discussed in terms of fibre diameter. 25 refs. Massachusetts,University; US,Army,Natick Soldier Systems Center USA
Accession no.999812 Item 240 ANTEC 2007. Proceedings of the 65th SPE Annual conference held Cincinnati, Oh., 6th-11th May 2007. Brookfield, Ct., SPE, 2007, p.1067-1071, PDF 0215, CD-ROM, 012 ASPECTS OF ELECTROSPINNING PROCESS CONTROL FROM FUNDAMENTAL MECHANISMS Stanger J J; Tucker N; Larsen N; Staiger M; Reeves R For large-scale application of electrospinning technology, it is important to know how to maximise and control the deposition rate of spun fibre. Driving polarity, substrate material and current flow were examined to quantify their effect on fibre deposition rate. Conductivity of the substrate and polarity of driving electric charge were found to affect the mass deposition rate. Higher deposition rates were the result of the production of thicker fibres and an increase in deposition speed. 17 refs. Christchurch,Crop & Food Research; Canterbury,University (SPE) NEW ZEALAND
Accession no.999407 Item 241 ANTEC 2007. Proceedings of the 65th SPE Annual conference held Cincinnati, Oh., 6th-11th May 2007. Brookfield, Ct., SPE, 2007, p.795-800, PDF 0451, CDROM, 012 EFFECTS OF MOLECULAR WEIGHT DISTRIBUTION ON THE FORMATION OF FIBERS OF ELECTROSPUN POLYSTYRENE Xiaoshu Dai
© Copyright 2008 Smithers Rapra Technology
It is widely recognised that molecular weight distribution (MWD) is an important factor affecting the rheological behaviour of polymer solutions. In this contribution, the effects of MWD on the formation of electrospun polystyrene fibres in THF have been studied. The results are compared with the monodisperse system. The importance of chain entanglements attributed to high molecular weight component within the polydisperse system has been acknowledged. Concentrations for the incipient as well as stable fibre formation in a polydisperse system may be predicted. 7 refs. Worcester,Polytechnic Institute (SPE) USA
Accession no.999360 Item 242 ANTEC 2007. Proceedings of the 65th SPE Annual conference held Cincinnati, Oh., 6th-11th May 2007. Brookfield, Ct., SPE, 2007, p.785-794, PDF 0285, CDROM, 012 EFFECT OF POLARITY ON ELECTROSPINNING POLYCAPROLACTONE TISSUE ENGINEERING SCAFFOLDS Lippincott H; Crugnola A M Electrospun polycaprolactone (PCL) fabric was affected by the electrospinning voltage polarity. The tensile test breaking strain and breaking stress of negative polarity spun samples was half that of positive polarity samples. The differences were investigated using XRD, DSC, scanning electron microscopy (SEM), and mercury porosimetry. XRD found a peak of a different magnitude, but DSC found no significant differences in crystallinity. The SEM show few differences, but the porosimetry shows a different distribution. Recent articles by P. Supaphol (2), (3) challenged the assumption that there is no effect of high voltage polarity on the electrospinning (Espin) process and product. This study examined the effect of polarity on the mechanical and physical properties and processing of Espun polycaprolactone (PCL) in acetone. The ultimate tensile test results were startling: the negative polarity samples broke at one half the elongation, 28% vs. 60%, and only achieved a UTS of 0.23 MPa, one half the positive polarity's 0.51 MPa. While the total porosity of the samples was insignificantly different (74.5%+/-1.3% positive and 77.4% +/-1.8% negative), the distribution of pore sizes determined by mercury porosimetry was less uniform for Positive samples ,with a strong peak at 5 micrometre. The Espin process differed also: more (39%) of the PCL was attracted to the target and its edges when the polarity was positive vs. only 31% when the polarity was negative. However, the negative polarity put more PCL onto the front of the target, 45% vs. 39% for positive, leaving the front samples of similar thicknesses and average porosities. These properties of the fabric were significantly different in ways that may affect its use as a tissue engineering scaffold. 4 refs.
89
References and Abstracts
Massachusetts,University (SPE) USA
Accession no.999359 Item 243 Macromolecules 40, No.5, 6th March 2007, p.1693. EVIDENCE FOR MOLECULAR ORIENTATION AND RESIDUAL CHARGE IN THE ELECTROSPINNING OF POLY(BUTYLENE TEREPHTHALATE) NANOFIBERS Catalani L H; Collins G; Jaffe M PBTP electrospun fibres were analysed by a thermally stimulated current method. The fibres showed unexpected molecular and crystalline orientation. This orientation may have resulted from electrostatic forces which operated during the formation of the non-woven fibre structure. Relative to the ground plate take-up, the electrospun mat was polarised which showed that electrostatic forces during electrospinning could affect the development of the solid polymer microstructure. In the absence of an electric field, a spontaneous current was released near the glass transition, indicating a dipole relaxation process. A monotonic increase in current generated by dissipation of residual charge was observed with increasing temperature below the melting point. A peak in the charge dissipation current near the melting point indicated that a considerable amount of residual charge was trapped within or at the interface of the crystalline phase. The molecular orientation was studied by birefringence analysis. Electrospun fibres showed a high level of birefringence which was extinguished on melting. 16 refs. New Jersey,Institute of Technology USA
Accession no.999347 Item 244 Smart Materials and Structures 16, No.3, June 2007, p.575. ELECTROSTATICALLY TUNABLE BENDING STIFFNESS IN A GFRP-CFRP COMPOSITE BEAM Bergamini A; Christen R; Motavalli M
Item 245 Polymer 48, No.14, 2007, p.3974. PREPARATION OF WATER-STABLE SUBMICRON FIBERS FROM AQUEOUS LATEX DISPERSION OF WATER-INSOLUBLE POLYMERS BY ELECTROSPINNING Stoiljkovic A; Ishaque M; Justus U; Hamel L; Klimov E; Heckmann W; Eckhardt B; Wendorff J H; Greiner A Submicron polystyrene (PS) fibres were prepared by electrospinning of an aqueous dispersion of PS latex and a small amount of poly(vinyl alcohol) (PVA) and subsequent extraction by water. Depending on particle size, surfactant, ratio of PS:PVA, and applied voltage fibres of different morphology and water stability were obtained. Analysis of latex fibres by TEM revealed hexagonal packaging of particles within the fibres. 30 refs. Marburg,Philipps Universitat; BASF EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; WESTERN EUROPE
Accession no.999097 Item 246 Colloid and Polymer Science 285, No.8, May 2007, p.855. PREPARATION OF ELECTROSPUN CHITOSAN/ POLY(VINYL ALCOHOL) MEMBRANES Yuanyuan Zhang; Xiaobo Huang; Bin Duan; Lili Wu; Shuo Li; Xiaoyan Yuan Chitosan fibres were produced by electrospinning of Chitosan solutions in 2% aqueous acetic acid using PVAl as a "guest" polymer and structurally characterised by scanning electron microscopy, TEM, FTIR spectroscopy and X-ray diffraction. The effects of polymer concentration, chitosan/PVAl mass ratio and processing parameters, such as voltage, capillary-to-collector distance and flow rate, on the electrospinnability of the fibres were investigated The water uptake of the fibres was also investigated and the potential use of the fibres as wound dressings briefly considered. 29 refs. Tianjin,University CHINA
Accession no.998236
The stiffness of a GRP sandwich beam was modified to suppress vibrations due to resonance by applying an electric field between the main element of the structure and additional stiffening elements (CFRP) applied to its surface, thereby coupling the latter to the former by transfer of shear stresses and the bending stiffness of the beam investigated. The effect of electrostatic tuning of the bending stiffness is demonstrated and the discrete character of stiffness increase postulated. 7 refs. EMPA
Item 247 ANTEC 2007. Proceedings of the 65th SPE Annual conference held Cincinnati, Oh., 6th-11th May 2007. Brookfield, Ct., SPE, 2007, p.27-31, PDF 0721, CDROM, 012 INTERFACIAL ADHESION BETWEEN HYDROXYAPATITE AND POLY(ECAPROLACTONE) AND THEIR ELECTROSPUN COMPOSITE TOUGHNESS Wong S C; Baji A
SWITZERLAND; WESTERN EUROPE
The interfacial adhesive strength between hydroxyapatite (HAP) and poly(epsilon-caprolactone) (PCL) were
Accession no.999158
90
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
determined using T-peel tests. Their composite fracture toughness was determined using essential work of fracture concept. Electrospinning techniques were employed to obtain nanometer scale PCL fibres with and without HAP reinforcements which also create micrometer-scale porosity in the structure. The effects of HAP morphology and HAP content on mechanical properties were evaluated. 14 refs.
Item 250 Synthetic Metals 157, No.6-7, 2007, pp.276. ELECTROSPUN POLYALKYLTHIOPHENE/ POLYETHYLENEOXIDE FIBERS: OPTICAL CHARACTERIZATION Bianco A; Bertarelli C; Frisk S; Rabolt J F; Gallazzi M C; Zerbi G
Akron,University (SPE)
Fibres were produced by electrospinning of blends of poly(ethylene oxide) (PEO) and poly(3dodecylthiophene) (P3DDT) from chloroform solution. The diameter of the fibres was approximately 1 micron, and both polymer components were present as separated phases in the fibres. The PEO matrix was completely removed by washing the fibres with acetonitrile to give long homogeneous P3DDT fibres. The morphology and structure of these fibres was examined by scanning electron microscopy (SEM) and confocal fluorescence microscopy, which confirmed that the fibres were homogeneous. IR spectroscopy was used to check for removal of the PEO matrix and to elucidate the conformation of the polythiophene chains and their orientation in the fibres. Polarized infrared spectroscopy showed that the polythiophene chains were generally aligned along the fibre axis. 44 refs. Delaware,University; Milan,Polytechnic
USA
Accession no.997384 Item 248 Polymer Materials Science and Engineering 23, No.2, March 2007, p.149. STUDY ON DISPERSION MORPHOLOGY AND CRYSTALLIZATION BEHAVIOR OF ELECTROSPUN NYLON 66 NANOFIBER MEMBRANES Tie-Jun Shi; Lin-Feng Zhai; Yu-Bo Zhou The effects of solution concentration, voltage and distance between electrodes on the dispersion morphology and diameter of polyamide-66 nanofibre membranes were investigated by field emission scanning electron microscopy. The effects of solution concentration and voltage on the crystallisation behaviour of the fibres were also investigated by means of X-ray diffraction. 9 refs. Hefei,University of Technology CHINA
Accession no.997006 Item 249 Proceedings of the American Society for Composites. Twenty-first Technical Conference. Proceedings of a conference held Dearborn, Mi., 17th-20th Sept.2006. Lancaster, Pa., DEStech Publications, 2006, Paper 28, CD-ROM, ISBN 1932078606, 012 ELECTROSPINNING OF QUANTUM DOT NANOCOMPOSITE FIBERS Yand H; Li H; Shih W-H; Ko F Fluorescent nanocomposite nanofibres consisting of cadmium selenide (quantum dots) and PEO were fabricated by electrospinning and characterised by field emission scanning electron microscopy, Raman spectroscopy and optical microscopy. The nanofibres exhibited strong fluorescent properties over several months without photobleaching at room temperature. They are considered suitable for a wide range of applications, including sensors, drug delivery, scaffolds for tissue engineering, camouflage and damage detection of composite structures. 38 refs. (American Society for Composites; MichiganDearborn,University) Accession no.996969
© Copyright 2008 Smithers Rapra Technology
EUROPEAN COMMUNITY; EUROPEAN UNION; ITALY; USA; WESTERN EUROPE
Accession no.996628 Item 251 Future Materials June 2007, p.12 ROBOTS CLIMBING THE WALLS Researchers at Carnegie Mellon University have engineered a robot that can scale glass walls and cross ceilings. The robot has two triangular wheel-like legs, each with three sticky footpads, and a tail. The springloaded tail provides a preload force, pressing the footpads against the surface. The robot currently uses a dry elastomer adhesive to cling to walls, but the scientists are fabricating a nanofibre system that will give it a geckolike grip. Geckos are able to cling to surfaces thanks to very fine hair-like structures, called setae, on their feet. The attractive forces that hold geckos to walls are weak molecular van der Waals interactions between the finely divided setae and the surfaces themselves. CMU's team is working on synthetic fibres that are twice as æsticky' as those on a gecko's feet. Carnegie-Mellon University USA
Accession no.996465 Item 252 Advanced Materials 19, No.4, 19th Feb.2007, p.521.
91
References and Abstracts
POLYDIACETYLENE SUPRAMOLECULES IN ELECTROSPUN MICROFIBERS: FABRICATION, MICROPATTERNING, AND SENSOR APPLICATIONS Sang Kyun Chae; Hyunwook Park; Jaewon Yoon; Cheol Hee Lee; Dong June Ahn; Jong-Man Kim Polymer microfibres encapsulating polydiacetylene(PDA) supramolecules were prepared by using the electrospinning technique. PEO and PMMA were selected as representative matrix polymers. Randomly distributed diacetylene monomers were found to self-assemble during fibre formation and enable the generation of blue-coloured PDA-containing polymer fibres upon UV irradiation. Micropatterned colour and fluorescence images from a single electrospun fibre were obtained by fluorescence generation upon specific ligand-receptor interactions, and the feasibility of a fibre-based sensor was demonstrated. 33 refs. Hanyang,University; Korea,University KOREA
Accession no.996233 Item 253 Advanced Materials 19, No.9, 7th May 2007, p.1228. TENSILE MECHANICS OF ELECTROSPUN MULTIWALLED NANOTUBE/POLY(METHYL METHACRYLATE) NANOFIBERS Liu L-Q; Tasis D; Prato M; Wagner H D The fabrication of multi-walled carbon nanotube (MWNT)-reinforced poly(methyl methacrylate)(PMMA) nanofibres by electrospinning and the characterisation of their morphology, MWNT distribution, orientation and stress-strain properties by TEM, ESEM and tensile testing is described. The effects of reinforcement by MWNT on the properties of the nanofibres are discussed in comparison with those for electrospun PMMA nanofibres. 27 refs. Weizmann Institute of Science; INSTM; Patras,University EUROPEAN COMMUNITY; EUROPEAN UNION; GREECE; ISRAEL; ITALY; WESTERN EUROPE
Accession no.995732 Item 254 Macromolecules 40, No.7, 3rd April 2007, p.2590. TIME-DEPENDENT TRANSFORMATION OF AN ELECTROSPUN ISOTACTIC POLY(1-BUTENE) FIBROUS MEMBRANE Keun-Hyung Lee; Snively C M; Givens S; Chase D B; Rabolt J F Isotactic poly(1-butene) fibrous membranes were prepared from polymer solutions via electrospinning using mixed solvents. The crystalline transformation of these fibres was studied by FTIR and Raman spectroscopies and by
92
wide angle X-ray diffraction and DSC. Although the electrospun fibres and the solvent cast film were both crystallised from the same polymer solution, different crystalline modifications were observed. This was thought to result from different solvent evaporation rates and stresses induced on the charged polymer solution during electrospinning. For the electrospun fibrous membrane, mixed crystalline structures of forms I and II existed at an early stage. The metastable form II was gradually transformed into the thermodynamically stable form I. The transformation was accelerated by heat treatment. A solvent cast film, however, showed a mixture of forms I' and III in which form III was the dominant crystalline structure. 31 refs. Delaware,University; Dupont Central Research & Development USA
Accession no.995307 Item 255 Macromolecular Symposia No.249/250 2007, p.289. ELECTROSPINNING OF POLY(ETHYLENE OXIDE) WITH BACTERIAL CELLULOSE WHISKERS Won-Il Park; Minsung Kang; Hun-Sik Kim; HyoungJoon Jin Bacterial cellulose whiskers were synthesised by acid hydrolysis of bacterial cellulose microfibrils and were blended in water with polyethylene oxide. The resulting mixed solution was electrospun into nanofibres, and these fibres were characterised using atomic force microscopy, scanning and transmission electron microscopy, and tensile studies on the electrospun mats. Incorporation of the whiskers into nanofibres of PEO was confirmed microscopically, and tensile properties of the composite were improved compared to plain PEO nanofibre mats. 12 refs. Inha,University KOREA
Accession no.994974 Item 256 Macromolecular Chemistry and Physics 208, No.9, 4th May 2007, p.1002. IMPACT OF SOLVENT ON ELECTROSPINNING OF ZEIN AND ANALYSIS OF RESULTING FIBERS Selling G W; Biswas A; Patel A; Walls D J; Dunlap C; Wei Y The fabrication of zein fibres by electrospinning from solutions in a range of solvents including acetic acid, aqueous methanol, ethanol, isopropanol and acetone was investigated and the fibres were characterised by FTIR, Raman spectroscopy, optical microscopy, and SEM. The results are discussed in terms of the effects of solvent on
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
fibre morphology, size distribution, birefringence and orientation. 34 refs.
Virginia,Commonwealth University; Philip Morris USA
US,Dept.of Agriculture,Agricultural Res.Service; Drexel,University; Du Pont de Nemours E.I.,& Co.Inc.
Accession no.994520
USA
Item 259 Journal of Colloid and Interface Science 311, No.1, 2007, p.529. CONTROLLABLE POROUS POLYMER PARTICLES GENERATED BY ELECTROSPRAYING Yiquan Wu; Clark R L
Accession no.994917 Item 257 Polymer Engineering and Science 47, No.5, May 2007, p.707. AN APPLICABLE ELECTROSPINNING PROCESS FOR FABRICATING A MECHANICALLY IMPROVED NANOFIBER MAT Kim G H; Han H; Park J H; Kim W D Engineered polymer scaffolds play an important role in tissue engineering. An ideal scaffold should have good mechanical properties and provide a biologically functional implant site. Considering their large surface area and high porosity, nanofibres have good potential as biomimetic scaffolds. However, the main shortcomings of scaffolds consisting of nanofibres are their mechanical inability to sustain a stress environment for neotissues and shape-ability to form a variety of shapes and sizes. In this study, we produced design-based poly (epsilon-caprolactone) (PCL) nanofibre mats using an electrospinning method with various auxiliary electrodes and an x-y moving system. To achieve stable initial solution at a nozzle tip of the electrospinning, various types of auxiliary electrodes were introduced. To characterize the effect of the electrodes in the electricfield distribution near the nozzle tip, we calculated the electric field concentration factor and compared it with the experimental results. The nanofibre mat produced using the moving x-y target system demonstrated orthotropic mechanical properties due to the fibre orientation, and human dermal fibroblasts seeded on the structure tended to grow according to nanofibre orientation. 14 refs. Korea,Institute of Machinery & Materials KOREA
Accession no.994755 Item 258 Macromolecular Rapid Communications 28, No.9, 2nd May 2007, p.1034. BIASED AS ELECTROSPINNING OF ALIGNED POLYMER NANOFIBERS Sarkar S; Deevi S; Tepper G A new method for minimising the inherent fibre instability in the electrospinning process is reported. Biased AC electrospinning employs a combination of DC and AC potentials and results in a highly aligned mat of polymer or composite polymer fibres. The relationship between specific processing variables and magnitude of the DC offset is investigated and related to fibre uniformity and stability. 26 refs.
© Copyright 2008 Smithers Rapra Technology
USA
In this paper, an electrospraying technique was applied to prepare polycaprolactone (PCL) polymer particles with a different microstructure. The PCL particles can be controlled to have a porous microstructure by tailoring the evaporation of solvents during the electrospraying process. The effect of various concentrations on the morphology and microstructure of PCL particles was investigated. The experiment has demonstrated the versatile capability of the electrohydrodynamic atomization process for preparing polymer PCL porous particles and fibres. The thermally induced and evaporation-induced phase separations are proposed as the main mechanisms for the porous microstructure formation. The results demonstrate that the electrospraying method is a simple, innovative and cost-effective method for preparing polymer particles with controllable microstructures. 32 refs. Durham,Duke University USA
Accession no.994409 Item 260 Polymer Materials Science and Engineering 23, No.1, Jan.2007, p.250. TENTATIVE STUDY ON ELECTROSPINNING OF POLY(ARYLENE SULFIDE SULFONE) NANOFIBERS Heng-Mei Huang; Xiao-Jun Wang; Bin Yu; Jie Yang; Guang-Xian Li Polyarylene sulphide sulphone dissolved in a mixed solvent of phenol and 1,1,2,2-tetrachloroethane, was electrospun into fibres and the effects of the solution components, environmental temperature, applied voltage and tip-screen distance on the morphology of the nanofibres investigated. 4 refs. Sichuan,University CHINA
Accession no.993834 Item 261 Polymer Materials Science and Engineering 23, No.1, Jan.2007, p.112. MORPHOLOGY AND IN VITRO DEGRADATION STUDIES OF ELECTROSPUN PLLA/MWNTS/HA HYBRID NANOFIBER SCAFFOLDS
93
References and Abstracts
Min-Li Zhao; Gang Sui; Xiao-Ping Yang; Xu-Liang Deng; Xiao-Yang Hu Poly(L-lactic acid)/multiwalled carbon nanotubes/ hydroxyapatite nanofibrous scaffolds having high porosity and well-controlled pore structure were produced by electrospinning and the surface degradation behaviour, viscosity-average molec.wt., weight loss, water uptake and pH of the fibre mats as a function of degradation time investigated. The alkaline nanotube/hydroxyapatite nanoparticles were found to slow down degradation rate. 9 refs. Beijing,University of Chemistry and Technology; Beijing,University CHINA
Accession no.993807 Item 262 European Polymer Journal 43, No.5, 2007, p.1609. ELECTROSPINNING OF POLY(VINYL PYRROLIDONE)-IODINE COMPLEX AND POLY(ETHYLENE OXIDE)/POLY(VINYL PYRROLIDONE)-IODINE COMPLEX - A PROSPECTIVE ROUTE TO ANTIMICROBIAL WOUND DRESSING MATERIALS Ignatova M; Manolova N; Rashkov I New nanofibres containing poly(vinyl pyrrolidone)-iodine complex (PVP-iodine) were obtained by electrospinning in order to prepare materials suitable for wound dressings. Different approaches were used: a one-step method based on electrospinning of PVP-iodine or poly(ethylene oxide)/ PVP-iodine solutions and a three-step method based on electrospinning of PVP or poly(ethylene oxide)/PVP mixed solutions followed by photo-mediated crosslinking of the obtained nanofibres and subsequent complexation with iodine. The average diameters of the fibres were in the range 150-470nm depending on the composition and on the applied field strength (AFS) and increased with increasing the amount of PEO in the spinning solutions. Higher AFS resulted in greater fibre diameter and in size distribution broadening. Photo-mediated crosslinking in the presence of 4,4'-diazidostilbene-2,2'-disulfonic acid disodium salt successfully stabilised the electrospun PVP and PEO/PVP nanofibres against water and water vapour. 27 refs. Bulgarian Academy of Sciences
a calcium phosphate based sol. The sol was prepared by reacting triethyl phosphite and calcium nitrate and was directly added to an aqueous solution of PVA. This mixture was electrospun at a voltage of 20 kV. The results indicate that the sol was distributed uniformly in the PVA fibres, whose diameter was on the order of 2 micrometer. This electrospun structure was calcined at 600 deg.C for 6 h to obtain a residual inorganic, fibrous network, with fibre diameters between 200 and 800 nm. The fibrous structure consists predominantly of hydroxyapatite with an average crystal size of almost 10 to 30 nm. A variety of structures including non-woven mats of solid or micro-porous hydroxyapatite fibres and highly porous scaffolds could be obtained by varying the polymer molecular weight and the sol volume fraction. These structures can have many potential uses in the repair and treatment of bone defects, drug delivery and tissue engineering. 19 refs. Worcester,Polytechnic Institute USA
Accession no.993546 Item 264 Journal of Applied Polymer Science 104, No.5, 5th June 2007, p.3245. STUDY OF ELECTROSPINNING OF SODIUM ALGINATE, BLENDED SOLUTIONS OF SODIUM ALGINATE/POLY(VINYL ALCOHOL) AND SODIUM ALGINATE/POLY(ETHYLENE OXIDE) Safi S; Morshed M; Ravandi S A H; Ghiaci M It was shown that the addition of various polymers, including polyvinyl alcohol (PVAl) or polyethylene oxide (PEO) to sodium alginate solution allowed the electrospinning of the blend into ultrafine nanofibres, something not possible with sodium alginate solution alone. A blend solution incorporating both PVAl and PEO was used for optimum results and nanofibres were characterised using scanning electron microscopy and Fourier transform infrared spectroscopy. Viscosities of spinning solutions were measured to determine the effects of polymer addition, and it was noted that solution viscosity had an effect on fibre morphology. 29 refs. Isfahan,University of Technology IRAN
Accession no.993515
Item 263 Materials Letters 61, No.13, 2007, p.2735. ELECTROSPINNING OF HYDROXYAPATITE FIBROUS MATS Xiaoshu Dai; Shivkumar S
Item 265 Polymer 48, No.9, 2007, p.2720. BIS-GMA/TEGDMA DENTAL COMPOSITES REINFORCED WITH ELECTROSPUN NYLON 6 NANOCOMPOSITE NANOFIBERS CONTAINING HIGHLY ALIGNED FIBRILLAR SILICATE SINGLE CRYSTALS Ming Tian; Yi Gao; Yi Liu; Yiliang Liao; Riwei Xu; Hedin N E; Hao Fong
Polyvinyl alcohol (PVA) with an average molecular weight between 40,500 and 155,000 g/mol was electrospun with
The objective of this research was to study the reinforcement of electrospun nylon 6/fibrillar silicate nanocomposite
BULGARIA; EASTERN EUROPE
Accession no.993590
94
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
nanofibres on Bis-GMA/TEGDMA dental composites. The hypothesis was that the uniform distribution of nanoscaled and highly aligned fibrillar silicate single crystals into electrospun nylon 6 nanofibres would improve the mechanical properties of the resulting nanocomposite nanofibres, and would lead to the effective reinforcement of dental composites. The nylon 6/fibrillar silicate nanocomposite nanofibres were crystalline, structurally oriented and had an average diameter of approximately 250 nm. To relatively well distribute nanofibres in dental composites, the nanofibre containing composite powders with a particle structure similar to that in interpenetration networks were prepared first, and then used to make the dental composites. The results indicated that small mass fractions (1% and 2%) of nanofibre impregnation improved the mechanical properties substantially, while larger mass factions (4% and 8%) of nanofibre impregnation resulted in less desired mechanical properties. 23 refs. South Dakota,School of Mines & Technology; Beijing,University of Chemical Technology CHINA; USA
Accession no.993205 Item 266 Materials Letters 61, No.11-12, 2007, p.2556. FABRICATION OF SEMICONDUCTOR NANOSTRUCTURES ON THE OUTER SURFACES OF POLYACRYLONITRILE NANOFIBERS BY IN-SITU ELECTROSPINNING Fengxia Dong; Zhenyu Li; Huiming Huang; Fan Yang; Wei Zheng; Ce Wang In this paper, in-situ electrospinning method was presented to directly fabricate semiconductor (Ag"2S or Cu"2S) nanostructures on the outer surfaces of polyacrylonitrile (PAN) nanofibres. PAN/metallic salt composite fibres were electrospun firstly as precursors, after UV irradiation photoreduction and the treatment of H"2S gas, Ag"2S or Cu"2S nanostructures can be obtained on the outer surface of PAN nanofibres. The interactions between the polymer and metallic ions are believed to be the main factor in determining the position of metallic ions based on the electrospun nanofibres. Transmission electron microscopy (TEM) and Fourier transform infrared (FTIR) are used to characterize the products. 33 refs. Jilin,University CHINA
Accession no.993163 Item 267 Materials Letters 61, No.11-12, 2007, p.2159. PREPARATION OF PVP/MEH-PPV COMPOSITE POLYMER FIBERS BY ELECTROSPINNING AND STUDY OF THEIR PHOTOELECTRONIC CHARACTERQIANG ZHAO; ZONGHAO
© Copyright 2008 Smithers Rapra Technology
HUANG; CHENG WANG; QIDONG ZHAO; HAIZHU SUN; DEJUN WANG Ultrafine polyvinylpyrrolidone (PVP)/poly[2-methoxy5-(2'-ethyl-hexyloxy)-1,4-phenylene vinylene] (MEHPPV) composite fibres were successfully prepared by electrospinning of PVP/MEH-PPV blend solutions in solvent mixtures of 1,2-dichloroethane/chlorobenzene. Composite polymer fibres with smooth surface were obtained using solutions in which MEH-PPV's concentration was 1.0 wt%. Compared with the MEH-PPV solution and bulk, PVP/MEH-PPV fibres show a significant blue shift, a stronger intensity of fluorescence and a higher surface photovoltage (SPV). The morphology of fibres has been characterized by scanning electron microscopy (SEM) and fluorescence microscopy. 20 refs. China,Northeast Normal University; Jilin,University CHINA
Accession no.993158 Item 268 Journal of Polymer Science: Polymer Physics Edition 45, No.7, 1st April 2007, p.766. ELECTROSPINNING OF ULTRAHIGHMOLECULAR-WEIGHT POLYETHYLENE NANOFIBERS Rein D M; Shavit-Hadar L; Khalfin R L; Cohen Y; Shuster K; Zussman E The electrospinning method was employed to fabricate, for the first time, ultrafine nanofibres of UHMWPE with a mixture of solvents of different dielectric constants and conductivities. These nanofibres could be an advanced source material for subsequent drawing to form strong nanofibres. The morphological, structural and mechanical properties of the nanofibres were studied. The possibility of producing highly oriented nanofibres from UHMW polymers indicated new ways of fabricating ultra-strong, porous, and single-component nanocomposite fibres with improved properties. 43 refs. Technion-Israel Institute of Technology ISRAEL
Accession no.993021 Item 269 Macromolecular Rapid Communications 28, No.5, 1st March 2007, p.651. COLOR CHANGE OF ELECTROSPUN POLYSTYRENE/MEH-PPV FIBERS FROM ORANGE TO YELLOW THROUGH PARTIAL DECOMPOSITION OF MEH SIDE GROUPS Chuangchote S; Srikhirin T; Supaphol P The electrospinning of PS/poly(2-methoxy-5-(2'ethylhexyloxy)-1,4-phenylene vinylene)(MEH-PPV) fibres with average diameters ranging from 0.165 to 1.190 micrometres from 7.5:1 w/w solutions of PS/MEH-PPV in 1,2-dichloroethane was studied. With the addition of
95
References and Abstracts
pyridinium formate(PF), a volatile organic salt, to the PS/MEH-PPV solution, the electrospinnability of the resulting solution was enhanced significantly. Both the fibre diameters and the number of fibres were found to increase, while the number of beads was found to decrease with increasing applied electrical potential, the addition of PF, and increasing ageing period of the spinning solution after PF addition. FTIR analysis showed that about 15% of the MEH side groups was removed from the MEH-PPV component in the fibres obtained from the solution that was left to age for 1 month after PF addition, which corresponded well to the loss of mass of about 7% as observed by TGA. As a result, partial decomposition of the MEH side groups should be responsible for the observed yellow emission colour of the PS/MEH-PPV fibres obtained from the same solution. 22 refs. Chulalongkorn,University; Mahidol University THAILAND
Accession no.993014 Item 270 Molecular Crystals and Liquid Crystals 464, 2007, p.719. MORPHOLOGICAL CHARACTERISTICS OF ELECTROSPUN POLY(METHYL METHACRYLATE) NANOFIBERS CONTAINING MULTI-WALLED CARBON NANOTUBES Dong Ouk Kim; Jae Do Nam; Dai Hoe Lee; Jun Young Lee; Jong-Jin Park; Jong Min Kim The electrospinning process was used to embed multiwalled carbon nanotubes(MWNTs) in electrospun nanofibres of PMMA for anisotropic alignment and effective dispersion of carbon nanotubes in the transparent polymer substrate. The morphology of MWNT-incorporated electrospun nanofibres was markedly influenced by the type of solvent and the content of carbon nanotubes, and exhibited various forms of beads, undulated fibres or uniform fibres. In the fibrous forms of electrospun PMMA, the MWNTs were mostly attached on the surface of polymer by physical interlocking. When the bead-shaped PMMA was produced by the electrospinning process, however, most of the MWNTs were embedded in the PMMA matrix without being exposed on the polymer surfaces. Using the oxygen plasma treatment for cutting-off the polymer-rich surface layer of the beads, the embedded MWNTs were exposed out of the beads and subsequently an urchin-shaped structure was obtained. The protruded MWNTs of the urchin-shaped beads could stabilise the polymer beads by the steric stabilisation in the solution state and provide facile electronic pathway and percolation in the condensed solid state. 15 refs. (KoreaJapan Joint Forum 2005, Daejeon, Korea, Oct.2005) Sung Kyun Kwan,Advanced Institute of Nanotechnology; Samsung SDI Corporate R & D
96
Centre; Sung Kyun Kwan University; Samsung Advanced Institute of Technology KOREA
Accession no.992979 Item 271 Molecular Crystals and Liquid Crystals 464, 2007, p.647. EFFECT OF ELECTROLYTE IN ELECTROSPUN PEO/TIO"2 COMPOSITE FIBERS Hooi-Sung Kim; Mi-Ra Kim; Hyo-Jin Kang; Jin-Kook Lee The effect of lithium perchlorate and titanium dioxide particles on electrospinning of PEO was studied with the aim of fabricating titanium dioxide electrodes for dyesensitised solar cells. Fibres were analysed using optical microscopy and SEM. The optimum amount of salt content induced stable fibre formation, while too high a salt content induced an increase of diameter and non-continuous fibre formation. Fibre combining was observed during the electrospinning process from the samples containing 10 mmol or more of salt. 9 refs. (Korea-Japan Joint Forum 2005, Daejeon, Korea, Oct.2005) Oregon Medical Laser Center; Pusan,National University KOREA; USA
Accession no.992975 Item 272 Polymers for Advanced Technologies 18, No.3, March 2007, p.180. EFFECT OF NEEDLE DIAMETER ON NANOFIBER DIAMETER AND THERMAL PROPERTIES OF ELECTROSPUN POLY(METHYL METHACRYLATE) Macossay J; Marruffo A; Rincon R; Eubanks T; Anxiu Kuang The effect of needle diameter on the resulting electrospun PMMA average nanofibre diameter was evaluated for three different needle gauges. The resulting nanofibres were observed and analysed by SEM, suggesting a lack of correlation between the needle diameter used and the resulting average nanofibre diameter. TGA indicated an increase in the thermal stability of PMMA nanofibres when compared with powdered PMMA, while DSC studies evidenced lower Tgs for PMMA nanofibres in the first heating cycle. 26 refs. Texas,Pan American University USA
Accession no.992939 Item 273 High Performance Polymers 19, No.2, April 2007 p.147. PREPARATION AND CHARACTERIZATION OF CORE-SHELL STRUCTURED NANOFIBERS BY COAXIAL ELECTROSPINNING
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
Xiaojian Han; Zhengming Huang; Chuanglong He; Ling Liu Coaxial electrospinning of two polymer solutions was used to prepare functional core-shell nanofibres with a polyurethane shell and a polyamide-6 core. Core-shell ratio could be varied by variation of solution concentration. Non-woven mats of the nanofibres were applied to cotton fabrics and the water vapour transmission properties and pliability of the treated fabrics was assessed. Nanofibres were characterised using scanning and transmission electron microscopy, tensile testing and Fourier transform infrared spectroscopy. 20 refs. Tongji,University CHINA
Accession no.992399 Item 274 Journal of Applied Polymer Science 104, No.3, 5th May 2007 p.1640. POLY(LACTIDE) NANOFIBERS PRODUCED BY A MELT-ELECTROSPINNING SYSTEM WITH A LASER MELTING DEVICE Ogata N; Yamaguchi S; Shimada N; G Lu; Iwata T; Nakane K; Ogihara T Carbon dioxide laser melting of a solid rod of a polylactide was used in the melt-electrospinning of nanofibres. The system was developed and described, and physical properties of the nanofibres produced from it were characterised using scanning electron microscopy, gel permeation chromatography, differential scanning calorimetry and X-ray diffraction. It was shown that fibres of less than 1 micron could be formed, with fibre diameter reduced as laser power was increased. Increasing laser power resulted in a decrease in molecular weight and melting point of the polylactide. As-spun fibres were amorphous, but on annealing crystallisation occurred. 14 refs. Fukui,University JAPAN
Accession no.992342 Item 275 European Polymer Journal 43, No.4, 2007, p.1154. SOLVENT EFFECTS ON JET EVOLUTION DURING ELECTROSPINNING OF SEMIDILUTE POLYSTYRENE SOLUTIONS Eda G; Liu J; Shivkumar S Linear polystyrene with a weight average molecular weight of 393400 g/mol was used with various solvents including tetrahydrofuran (THF), chloroform, carbon disulphide (CS"2), 1-methyl-2-pyrrolidinone (NMP), and N,N-dimethylformamide (DMF) to produce solutions, corresponding to a Berry number of about 9. The jet breakdown behaviour of each of these solutions
© Copyright 2008 Smithers Rapra Technology
was studied with a high speed camera (2000 frames/s). The structure of the electrospun polymer was examined with a scanning electron microscope. The results indicate that jet breakdown with THF and chloroform entailed significant extensional flow, followed by the onset of instabilities, leading to the formation of numerous secondary jets under steady-state conditions. By comparison, the solution jets with DMF and NMP exhibit extensive whipping and splaying to produce a cloud of jets. In this case, few secondary jets were observed under steady-state conditions. A highly refined structure was observed in the electrospun polymer for NMP and DMF, in accordance with the extensive instabilities observed during jet breakdown. Limited jet instability observed with CS"2 solution suggests the significant effect of solvent evaporation. Typical primary jet velocities were measured to be on the order of 2-5 m/s. 31 refs. Worcester,Polytechnic Institute USA
Accession no.992051 Item 276 European Polymer Journal 43, No.4, 2007, p.1112. NOVEL ANTIBACTERIAL FIBERS OF QUATERNIZED CHITOSAN AND POLY(VINYL PYRROLIDONE) PREPARED BY ELECTROSPINNING Ignatova M; Manolova N; Rashkov I The preparation of continuous defect-free fibres from quaternised chitosan derivative (QCh) has been achieved by electrospinning of mixed aqueous solutions of QCh with poly(vinyl pyrrolidone) (PVP). The average fibre diameter significantly decreases from 2800 to 1500 nm on increasing the polyelectrolyte content. In order to impart to QCh/PVP electrospun fibres stability to water and water vapour, the fibres have been crosslinked by incorporation of photo-crosslinking additives into QCh/PVP spinning solutions and subsequent UV irradiation of the electrospun fibres. Photocrosslinked QCh-containing electrospun mats show high antibacterial activity against the Gram-positive bacteria Staphylococcus aureus and Gram-negative bacteria Escherichia coli. 23 refs. Bulgarian Academy of Sciences BULGARIA; EASTERN EUROPE
Accession no.992047 Item 277 Polimeros: Ciencia e Tecnologia 16, No.4, Oct.-Dec.2006, p.286. ELECTROSPINNING OF AQUEOUS SOLUTIONS OF POLY(VINYL ALCOHOL) Guerrini L M; Branciforti M C; Bretas R E S; De Oliveira M P
97
References and Abstracts
Polyvinyl alcohol was synthesised by solution polymerisation of vinyl acetate and nanofibres obtained by electrospinning in aqueous solution with and without aluminium chloride. Nanofibre morphology was studied by scanning electron microscopy and the degree of crystallinity determined by DSC and wide angle X-ray diffraction. The effects of electrical voltage and aluminium chloride on the morphology and average diameter of the fibres were investigated and the crystallinity of the nanofibres with and without salt compared with that of isotropic polyvinyl alcohol. 29 refs. Sao Carlos,Universidade Federal; Hexion Quimica Ind. e Com.SA BRAZIL
Accession no.991540 Item 278 Journal of Applied Polymer Science 104, No.2, 15th April 2007, p.1368. EFFECTS OF ETHYLENE CONTENT OF POLYETHYLENE-CO-VINYL ALCOHOL ON DIAMETERS OF FIBERS PRODUCED BY MELTELECTROSPINNING Ogata N; Lu G; Iwata T; Yamaguchi S; Nakane K; Ogihara T Details are given of the fabrication of fibres from EVOH copolymers with different ethylene contents using a meltelectrospinning system equipped with a carbon dioxidelaser melting device. The influence of ethylene content on fibre diameter and moisture regain were investigated. Physical properties are also discussed. 13 refs. Fukui,University; Beijing,University of Chemical Technology CHINA; JAPAN
Accession no.991535 Item 279 Journal of Applied Polymer Science 104, No.2, 15th April 2007, p.863. ELECTROSPINNING OF KERATIN/ POLYETHYLENE OXIDE BLEND NANOFIBERS Aluigi A; Varesano A; Montarsolo A; Vineis C; Ferrero F; Mazzuchetti G; Tonin C Wool keratin/polyethylene oxide nanofibres were electrospun from aqueous solutions of polymer blends under different operating conditions. The filaments were characterised with SEM, FTIR and DSC and compared with films of the same materials produced via casting. Structural changes due to the electrospinning process were investigated. 45 refs.
Item 280 Journal of Polymer Research 14, No.1, Feb.2007, p.53. ELECTROSPUN METHACRYLATE-BASED COPOLYMER/INDOMETHACIN FIBERS AND THEIR RELEASE CHARACTERISTICS OF INDOMETHACIN Pornsopone V; Supaphol P; Rangkupan R; Tantayanon S Three methacrylate-based copolymers, i.e. poly (methacrylic acid-co-methyl methacrylate)(E-L1OO), poly(ethyl acrylate-co-methyl methacrylate-cotrimethylammonioethyl methacrylate chloride)(E-RLPO) and poly(butyl methacrylate-co(2-dimethylaminoethyl) methacrylate-co-methyl methacrylate)(E-EPO), were successfully electrospun into fibres, using ethanol as the spinning solvent. Electrospinning of these methacrylate-based copolymers and indomethacin, a non-steroidal, anti-inflammatory drug, at 10% by weight of the copolymer, was only successful, however, when an equivolume of ethanol and ethyl acetate was used as the co-solvent system. The drug-loaded as-spun copolymeric fibres appeared to be flat, with size ranging from 1.2 to 2.5 micrometres. At 24 h, the amount of the drug released from these drug-loaded as-spun copolymer fibres was about 55%, 30% and 18% for drug-loaded as-spun E-EPO, E-L1OO and E-RLPO fibres, respectively. 14 refs. Chulalongkorn,University THAILAND
Accession no.990769 Item 281 E-Polymers No.26, 2007, p.1. CONSTRUCTION OF AN ARRANGED NANO-FIBROUS STRUCTURE BY SELFORGANIZATION OF A DESIGNED AMPHIPHILIC PEPTIDE BASED ON BETASTRAND Hattori M; Hayashi S; Yokoi H; Tanaka M; Kinoshita T The fabrication of beta-sheet monolayers by an amphiphilic peptide having an alternate sequence of hydrophobic and charged amino acid residues via the Langmuir-Blodgett method at an air-water interface and its transfer to a mica substrate with or without compression was investigated by FTIR, AFM and surface pressure-area isotherms. The results are discussed in terms of self-organisation with formation of an arranged nano-fibrous structure. 21 refs. Nagoya,Institute of Technology; Menicon Co.Ltd. JAPAN
Accession no.990271
CNR; Torino,Politecnico EUROPEAN COMMUNITY; EUROPEAN UNION; ITALY; WESTERN EUROPE
Accession no.991468
98
Item 282 Polymer 48, No.6, 2007, p.1459.
© Copyright 2008 Smithers Rapra Technology
References and Abstracts
PHOTOLUMINESCENCE OF POLYETHYLENE OXIDE-ZNO COMPOSITE ELECTROSPUN FIBERS Xiaomeng Sui; Changlu Shao; Yichun Liu Polyethylene oxide-ZnO (PEO-ZnO) composite fibres were prepared by electrospinning technique. The structural and optical properties were investigated using scanning electron microscopy (SEM), Fourier transform infrared (FT-IR) spectroscopy, and photoluminescence (PL). Results indicated that PEO passivated the interface defects and quenched the visible emission of ZnO quantum dots by forming O-Zn bonds with ZnO nanoparticles. To investigate the influence of electrospinning voltage on the PL of the composite fibres, the electrospinning voltage was adjusted from 12 to 18 kV. It was shown that the passivation effect of PEO could be enhanced by increasing the electrospinning voltage, and the fibres prepared at higher voltage exhibited more intense ultraviolet emission. 25 refs. China,Northeast Normal University CHINA
Accession no.990024 Item 283 Materials Letters 61, No.7, 2007, p.1451. FLIGHT PATH OF ELECTROSPUN POLYSTYRENE SOLUTIONS: EFFECTS OF MOLECULAR WEIGHT AND CONCENTRATION Eda G; Liu J; Shivkumar S The behaviour of the solution jet during electrospinning is a consequence of the balance between electrical, surface tension, and viscoelastic forces. Solution rheology, which is known to have a significant effect on the structure of the electrospun polymer, may also affect jet evolution and breakdown. In this study, the effect of polymer molecular weight and concentration on the behaviour of polystyrene solution jet was investigated using high speed camera (2000 frames/s). The results indicate that the degree of elongational flow, bending instability, and jet branching depends on polymer molecular weight and concentration. It was observed that jet thinning and solidification may occur at different distances from the capillary when the rheological conditions are varied. 14 refs. Worcester,Polytechnic Institute USA
Accession no.989992 Item 284 European Polymer Journal 43, No.3, 2007, p.802. PREPARATION AND STUDY OF PPV/PVA NANOFIBERS VIA ELECTROSPINNING PPV PRECURSOR ALCOHOL SOLUTION Wen Zhang; Eryun Yan; Zonghao Huang; Cheng Wang; Yi Xin; Qiang Zhao; Yanbin Tong
© Copyright 2008 Smithers Rapra Technology
We have found a simple method to prepare poly(phenylene vinylene) (PPV) nanofibres via electrospinning PPV precursor alcohol solution under annealed at 180 deg.C in a N"2 atmosphere. The nanofibres are uniform in diameter and long in decimetre magnitudes with resistance in decay, which makes them have potential applications in optical and electronic devices. The morphology can be better controlled by blend PPV precursor solution with poly(vinylalcohol) (PVA) aqueous solution. The fluorescence spectrum of PPV/PVA nanofibres exhibited appreciable blue shift, which made it possible to fabricate nanofibres with fluorescence from yellow-green to blue. 14 refs. China,Northeast Normal University; Jimei,Middle School; Heilongjiang,University CHINA
Accession no.989957 Item 285 Journal of Physics D 40, No.4, 21st Feb.2007, p.1068. GROWTH OF SUB-MICRON FIBRES OF PURE POLYANILINE USING THE ELECTROSPINNING TECHNIQUE Cardenas J R; De Franca M G O; De Vasconcelos E A; De Azevedo W M; Da Silva E F The formation of pure polyaniline fibres by the electrospinning method was studied. The fibres exhibited diameters ranging from hundreds of nanometres to a few micrometres and had lengths of hundreds of micrometres. The fibres were collected on silica/silicon and silicon wafer pieces in the form of isolated fibres. The implementation of an acetone bath was of key importance for the formation of fibres. The flux of the polymeric solution and the electric field between the spinneret and the grounded collector were also important. Morphological characterisation by SEM showed smooth fibre surfaces and lack of failure effects such as necking and fibrillation. The current-voltage characteristics were linear and the conductivity values varied in the range usually observed for partially doped polyaniline. 25 refs. Pernambuco,Universidade Federal BRAZIL
Accession no.989649 Item 286 International Fiber Journal 22, No.1, Feb.2007, p.36. LATEST DEVELOPMENTS IN MELTSPINNING PROCESS TECHNOLOGY FOR NONWOVENS Wilkie A E; Shuler B F Hills Inc.'s multi-component fibre technology for manufacture of non-woven fabrics is described and its use for development of a polymer distribution plate manufacturing system similar to printed circuit board technology is considered. Melt blowing, spunbond and
99
References and Abstracts
staple processes are discussed. It is shown that ultra-fine fibres down to nanofibre size can be produced via splitting and new melt blowing methods and that new additives, such as antimicrobials, phase change materials and fire retardants, can be added to the polymers. Hills Inc. USA
Accession no.989621 Item 287 Polymer Materials Science and Engineering 22, No.6, Nov.2006, p.229. STUDY ON A PREPARATION OF NOVEL NANO/ SUBMICRON-FIBER CATALYST Hong-Tao Wang; Tai-Qi Liu A nano/submicron-fibre catalyst was prepared from PVP and nano-titanium dioxide particles by electrospinning and the effect of nanoparticle content on fibre diameter investigated. The fibres were characterised by FTIR spectroscopy, X-ray diffraction, TEM and scanning electron microscopy. The fibres were found to exhibit high efficiency for the photocatalytic degradation of CH2O. 10 refs. Beijing,Institute of Petrochemical Technology; Beijing,University of Chemical Technology CHINA
Accession no.989468 Item 288 Advanced Materials 19, No.1, 8th Jan.2007, p.87. FIELD-DRIVEN BIOFUNCTIONALIZATION OF POLYMER FIBER SURFACES DURING ELECTROSPINNING Sun X-Y; Shankar R; Borner H G; Ghosh T K; Spontak RJ The fabrication of peptide-functionalised poly(ethylene oxide) microfibres by electrospinning from a solution of poly(ethylene oxide) containing a peptide-poly(ethylene oxide) conjugate obtained via solid-phase-supported peptide synthesis followed by atom transfer radical polymerisation is described. The products were characterised by SEM, AFM and XPS, and the effects of solution concentration and composition on the biofunctionalisation of the fibre surfaces are discussed. 44 refs. Max-Planck-Institut fuer Kolloid- & Grenzflaech.; North Carolina,State University EUROPEAN COMMUNITY; EUROPEAN UNION; GERMANY; USA; WESTERN EUROPE
Accession no.989147 Item 289 Polymer 48, No.5, 2007, p.1419.
100
BONE SCAFFOLDS FROM ELECTROSPUN FIBER MATS OF POLY(3-HYDROXYBUTYRATE), POLY(3-HYDROXYBUTYRATE-CO-3HYDROXYVALERATE) AND THEIR BLEND Sombatmankhong K; Sanchavanakit N; Pavasant P; Supaphol P In the present contribution, electrospinning was used to fabricate ultrafine fibre mats from poly(3-hydroxybutyrate) (PHB), poly(3-hydroxybutyrate-co-2-hydroxyvalerate) (PHBV), and their 50/50w/w blend for potential use as bone scaffolds. Cytotoxicity evaluation of these as-spun fibre mats with human osteoblasts (SaOS-2) and mouse fibroblasts (L929) indicated biocompatibility of these materials to both types of cells. The potential for use of these fibre mats as bone scaffolds was further assessed in vitro in terms of the attachment, the proliferation, and the alkaline phosphatase (ALP) activity of SaOS-2 that were seeded or cultured at different times. The cells appeared to adhere well on all types of the fibrous scaffolds after 16h of cell seeding. During the early stage of the proliferation period (i.e., from ~24 to 72h in culture), the viability of the cells increased considerably and appeared to be unchanged with further increase in the time in culture. In comparison with the corresponding solution-cast film scaffolds, all of the fibrous scaffolds exhibited much better support for cell attachment and proliferation. Lastly, among the various fibrous scaffolds investigated, the electrospun fibre mat of the 50/50w/w PHB/PHBV blend showed the highest ALP activity. These results implied a high potential for use of these electrospun fibre mats as bone scaffolds. 28 refs. Chulalongkorn,University THAILAND
Accession no.988887 Item 290 Advanced Functional Materials 16, No.18, 4th Dec.2006, p.2393. FABRICATION OF ELECTROSPINNINGDERIVED CARBON NANOFIBER WEBS FOR THE ANODE MATERIAL OF LITHIUM-ION SECONDARY BATTERIES Chan Kim; Kap Seung Yang; Masahito Kojima; Kazuto Yoshida; Yong Jung Kim; Yoong Ahm Kim; Morinobu Endo A carbon nanofibre-based electrode, exhibiti