01_080139 ffirs.qxp
3/26/07
3:14 PM
Page iii
SolidWorks 2007 Bible
Matt Lombard
®
01_080139 ffirs.qxp
3/26/07
...
28 downloads
1288 Views
41MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page iii
SolidWorks 2007 Bible
Matt Lombard
®
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page ii
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page i
SolidWorks 2007 Bible ®
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page ii
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page iii
SolidWorks 2007 Bible
Matt Lombard
®
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page iv
SolidWorks® 2007 Bible Published by Wiley Publishing, Inc. 10475 Crosspoint Boulevard Indianapolis, IN 46256 www.wiley.com
Copyright © 2007 by Wiley Publishing, Inc., Indianapolis, Indiana Published simultaneously in Canada ISBN: 978-0-470-08013-9 Manufactured in the United States of America 10 9 8 7 6 5 4 3 2 1 No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning or otherwise, except as permitted under Sections 107 or 108 of the 1976 United States Copyright Act, without either the prior written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to the Copyright Clearance Center, 222 Rosewood Drive, Danvers, MA 01923, (978) 750-8400, fax (978) 646-8600. Requests to the Publisher for permission should be addressed to the Legal Department, Wiley Publishing, Inc., 10475 Crosspoint Blvd., Indianapolis, IN 46256, (317) 572-3447, fax (317) 572-4355, or online at http://www.wiley.com/go/permissions. Limit of Liability/Disclaimer of Warranty: The publisher and the author make no representations or warranties with respect to the accuracy or completeness of the contents of this work and specifically disclaim all warranties, including without limitation warranties of fitness for a particular purpose. No warranty may be created or extended by sales or promotional materials. The advice and strategies contained herein may not be suitable for every situation. This work is sold with the understanding that the publisher is not engaged in rendering legal, accounting, or other professional services. If professional assistance is required, the services of a competent professional person should be sought. Neither the publisher nor the author shall be liable for damages arising herefrom. The fact that an organization or Website is referred to in this work as a citation and/or a potential source of further information does not mean that the author or the publisher endorses the information the organization or Website may provide or recommendations it may make. Further, readers should be aware that Internet Websites listed in this work may have changed or disappeared between when this work was written and when it is read. For general information on our other products and services or to obtain technical support, please contact our Customer Care Department within the U.S. at (800) 762-2974, outside the U.S. at (317) 572-3993 or fax (317) 572-4002. Library of Congress Control Number: 2007924101 Trademarks: Wiley, the Wiley logo, and related trade dress are trademarks or registered trademarks of John Wiley & Sons, Inc. and/or its affiliates, in the United States and other countries, and may not be used without written permission. SolidWorks is a registered trademark of SolidWorks Corporation. All other trademarks are the property of their respective owners. Wiley Publishing, Inc., is not associated with any product or vendor mentioned in this book. Wiley also publishes its books in a variety of electronic formats. Some content that appears in print may not be available in electronic books.
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page v
About the Author Matt Lombard holds a mechanical engineering degree from Rochester Institute of Technology in Rochester, New York. Matt has worked as a design and manufacturing engineer in the medical and microelectronics industries. Currently, through his company Dezignstuff, he works mainly as a consumer product modeling consultant and technical writer. Before becoming an engineer, Matt went to music school for two years and performed with the Navy band for four years. He still plays in local community groups for fun. Having grown up in the Adirondack Mountains of northeastern New York, he now calls the Shenandoah Valley of Virginia home.
01_080139 ffirs.qxp
3/26/07
3:14 PM
Page vi
This work is dedicated to my grandparents, Earl “Boots” Woods and Mildred “Mid” Woods, who taught me that the value of hard work goes beyond the numbers on a paycheck.
Credits Acquisitions Editor Jenny Watson
Project Coordinator Lynsey Osborn
Project Editor Martin V. Minner
Graphics and Production Specialists Stacie Brooks Denny Hager Jennifer Mayberry Barbara Moore Heather Pope
Technical Editor Richard Doyle Copy Editor Marylouise Wiack Editorial Manager Robyn Siesky Business Manager Amy Knies Vice President and Executive Group Publisher Richard Swadley Vice President and Publisher Barry Pruett
Quality Control Technicians Laura Albert Brian Walls Proofreading Aptara Indexing Aptara Cover Design Michael Trent Cover Illustration Joyce Haughey
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page vii
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxiii Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxvii
Part I: SolidWorks Basics
1
Chapter 1: Getting Familiar with SolidWorks . . . . . . . . . . . . . . . . . . 3 Understanding Feature-Based Modeling ................................................................................4 Understanding History-Based Modeling ................................................................................6 Sketching with Parametrics ..................................................................................................9 Understanding Design Intent ..............................................................................................14 Editing Design Intent ..........................................................................................................15 View, Sketch Relations ..............................................................................................15 Display/Delete Relations ............................................................................................15 Suppressed Sketch Relations......................................................................................16 Working with Associativity..................................................................................................16 Summary ............................................................................................................................16
Chapter 2: Navigating the SolidWorks Interface . . . . . . . . . . . . . . . . 19 Identifying Elements of the SolidWorks Interface ................................................................20 Toolbars ....................................................................................................................21 Menus ......................................................................................................................46 Cursors......................................................................................................................50 FeatureManager and PropertyManager windows........................................................51 Task pane ..................................................................................................................53 Status bar ..................................................................................................................54 2D Command Line Emulator ....................................................................................55 Making the Interface Work for You......................................................................................56 Customizing colors....................................................................................................56 Customization strategies ............................................................................................56 Working with multiple-document windows ..............................................................61 Tutorial: Getting to Know the Interface................................................................................63 Tutorial goals ............................................................................................................64 Copy the existing settings ..........................................................................................64 Set all interface items to their default settings ............................................................65 Customizing the CommandManager..........................................................................66 Customizing menus ..................................................................................................68
vii
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page viii
Contents
Change interface colors ............................................................................................69 Adding hotkeys ........................................................................................................70 Combining macros with hotkeys ..............................................................................71 Summary ............................................................................................................................71
Chapter 3: Getting Started with SolidWorks . . . . . . . . . . . . . . . . . . 73 Tools for Beginners ..............................................................................................................73 SolidWorks license agreement ..................................................................................74 Welcome to SolidWorks ............................................................................................74 Quick Tips ................................................................................................................75 Online documentation ..............................................................................................77 Hardcopy documentation ..........................................................................................78 Identifying SolidWorks Documents ....................................................................................79 Document types ........................................................................................................79 Saving your setup ......................................................................................................80 Templates ..................................................................................................................81 Opening Existing Documents..............................................................................................85 Opening a document ................................................................................................86 Understanding file references ....................................................................................87 Using Visualization Tools ....................................................................................................89 Changing the view ....................................................................................................89 Using color and optical properties ..........................................................................100 Tutorial: Creating a Part Template......................................................................................102 Tutorial: Visualization Techniques ....................................................................................105 Summary ..........................................................................................................................109
Chapter 4: Working with Sketches . . . . . . . . . . . . . . . . . . . . . . 111 Opening a Sketch ..............................................................................................................112 Identifying Sketch Entities ................................................................................................113 The Sketch toolbar ..................................................................................................113 The Dimensions/Relations toolbar ..........................................................................132 Inferencing in Sketch ........................................................................................................135 Exploring Sketch Settings..................................................................................................137 Using Sketch Blocks ..........................................................................................................138 Tutorial: Learning to Use Sketch Relations ........................................................................140 Tutorial: Using Blocks and Belts ........................................................................................143 Summary ..........................................................................................................................145
Chapter 5: Creating Simple Parts, Assemblies, and Drawings . . . . . . . . 147 Asking the Right Questions ..............................................................................................147 Is the part symmetrical? ..........................................................................................148 What are the primary or functional features? ..........................................................148 In what ways is the part likely to change? ................................................................148 What is the manufacturing method?........................................................................149 Will there be secondary operations? ........................................................................149 Will there be other versions? ..................................................................................150
viii
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page ix
Contents
Creating a Simple Part ......................................................................................................150 Where to start? ........................................................................................................150 Symmetry ................................................................................................................151 Make it solid............................................................................................................152 Making the groove ..................................................................................................158 Tutorial: Creating a Simple Assembly ................................................................................169 Tutorial: Making a Simple Drawing ..................................................................................174 Summary ..........................................................................................................................180
Part II: Building Intelligence into Your Parts
181
Chapter 6: Getting More from Your Sketches . . . . . . . . . . . . . . . . . 183 Editing Sketch Relations....................................................................................................183 Display/Delete relations ..........................................................................................184 SketchXpert ............................................................................................................186 Copying and Moving Sketch Entities ................................................................................187 Move entities ..........................................................................................................187 Rotate entities ..........................................................................................................187 Copy entities ..........................................................................................................188 Scale entities............................................................................................................188 Modify sketch..........................................................................................................188 Copy and paste........................................................................................................190 Simple drag ............................................................................................................190 Derived sketch ........................................................................................................190 Using Sketch Pictures ........................................................................................................191 Three views ............................................................................................................192 Perspective ..............................................................................................................192 Sharp edges ............................................................................................................193 Using Sketch Text..............................................................................................................193 Using Colors and Line Styles with Sketches ......................................................................195 Color Display mode ................................................................................................195 Line color ................................................................................................................195 Edit color ................................................................................................................195 Line thickness and line style ....................................................................................195 Tutorial: Editing and Copying ..........................................................................................196 Tutorial: Controlling Pictures, Text, Colors, and Styles ......................................................200 Summary ..........................................................................................................................203
Chapter 7: Choosing a Feature Type . . . . . . . . . . . . . . . . . . . . . . 205 Identifying When to Use Which Tool ................................................................................205 Extrude ..................................................................................................................206 Revolve....................................................................................................................210 Loft..........................................................................................................................211 Sweep......................................................................................................................221
ix
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page x
Contents
Creating Curve Features ....................................................................................................224 Helix ......................................................................................................................225 Projected curve........................................................................................................226 Curve Through XYZ Points......................................................................................228 Curve Through Reference Points ............................................................................230 Composite curve ....................................................................................................230 Split lines ................................................................................................................230 Filleting ............................................................................................................................231 Creating a constant radius fillet ..............................................................................233 Creating variable radius fillets..................................................................................240 Face fillet ................................................................................................................243 Full round fillet ......................................................................................................250 Setback fillet ............................................................................................................251 Selecting a Specialty Feature..............................................................................................254 Dome and Shape ....................................................................................................254 Wrap feature............................................................................................................257 Flex ........................................................................................................................260 Deform ....................................................................................................................263 Indent ....................................................................................................................266 Tutorial: Bracket Casting....................................................................................................267 Tutorial: Creating a Wire-Formed Part ..............................................................................272 Summary ..........................................................................................................................275
Chapter 8: Patterning and Mirroring . . . . . . . . . . . . . . . . . . . . . 277 Patterning in a Sketch ......................................................................................................277 A little test ..............................................................................................................277 Patterning a sketch ..................................................................................................278 Mirroring in a Sketch ........................................................................................................280 Mirror Entities ........................................................................................................281 Dynamic Mirror ......................................................................................................281 Symmetry sketch relation ........................................................................................282 Geometry Pattern ..............................................................................................................282 Patterning Bodies ..............................................................................................................283 Patterning Faces ................................................................................................................284 Patterning Fillets ..............................................................................................................285 Understanding Pattern Types ............................................................................................286 Linear Pattern ..........................................................................................................286 Circular Pattern ......................................................................................................288 Curve Driven Pattern ..............................................................................................289 Sketch Driven Pattern..............................................................................................292 Table Driven Pattern ................................................................................................294 Fill Pattern ..............................................................................................................295 Mirroring in 3D ................................................................................................................296 Mirroring bodies......................................................................................................296 Mirroring features....................................................................................................296 Mirroring entire parts ..............................................................................................297
x
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xi
Contents
Tutorial: Creating a Circular Pattern ..................................................................................297 Tutorial: Mirroring Features ..............................................................................................299 Summary ..........................................................................................................................301
Chapter 9: Using Equations . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Understanding Equations ..................................................................................................303 Creating equations ..................................................................................................304 Using driven dimensions ........................................................................................308 Equation tricks ........................................................................................................310 Using Link Values..............................................................................................................311 Using Global Variables ......................................................................................................313 Using Expressions ............................................................................................................313 Tutorial: Using Equations ..................................................................................................314 Summary ..........................................................................................................................315
Chapter 10: Working with Part Configurations . . . . . . . . . . . . . . . . 317 Controlling Items with Configurations ..............................................................................318 Finding configurations ............................................................................................318 Activating configurations ........................................................................................320 Creating configurations ..........................................................................................322 Derived configurations ............................................................................................324 File size considerations ............................................................................................324 Controlling dimensions ..........................................................................................325 Controlling suppression ..........................................................................................326 Controlling custom properties ................................................................................327 Controlling colors....................................................................................................328 Controlling sketch relations ....................................................................................328 Controlling sketch planes ........................................................................................329 Controlling configurations of inserted parts ............................................................330 Library features........................................................................................................331 Unconfigurable items ..............................................................................................332 Using Design Tables ..........................................................................................................332 What can be driven by a design table? ....................................................................333 Creating a simple design table ................................................................................334 Design table settings ................................................................................................340 Editing the design table ..........................................................................................341 Tutorial: Working with Configurations and Design Tables ................................................342 Summary ..........................................................................................................................346
Chapter 11: Editing and Evaluation . . . . . . . . . . . . . . . . . . . . . . 347 Using Rollback ..................................................................................................................347 Using the Rollback bar ............................................................................................348 Other Rollback techniques ......................................................................................353 Reordering Features ..........................................................................................................353 Reordering Folders ............................................................................................................355 Using the Flyout FeatureManager......................................................................................355 Summarizing Part Modeling Best Practice..........................................................................356
xi
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xii
Contents
Using Evaluation Techniques ............................................................................................359 Draft analysis ..........................................................................................................360 Thickness Analysis ..................................................................................................365 Undercut Detection ................................................................................................367 Verification on Rebuild ............................................................................................368 Check......................................................................................................................369 Reflective techniques ..............................................................................................370 COSMOSXpress ......................................................................................................374 MoldflowXpress ......................................................................................................377 Tutorial: Making Use of Editing and Evaluation Techniques ..............................................380 Summary ..........................................................................................................................387
Part III: Working with Assemblies
389
Chapter 12: Organizing Assemblies . . . . . . . . . . . . . . . . . . . . . . 391 Identifying the Elements of an Assembly ..........................................................................391 Standard reference geometry items ..........................................................................393 Assembly equations ................................................................................................393 Assembly layout sketch ..........................................................................................394 Assembly reference geometry ..................................................................................395 Parts and subassemblies ..........................................................................................396 Folders ....................................................................................................................396 Mates ......................................................................................................................396 Assembly features ....................................................................................................396 Component patterns................................................................................................396 In-context reference update holders ........................................................................397 Smart Fasteners ......................................................................................................397 Hole Series ..............................................................................................................397 Using Subassemblies ........................................................................................................398 Creating subassemblies from existing parts..............................................................399 Organizing for performance ....................................................................................400 Organizing for the BOM ..........................................................................................401 Grouping subassemblies by relative motion ............................................................402 Organizing groups of purchased components ..........................................................403 Depicting an assembly process ................................................................................403 Patterning considerations ........................................................................................404 Using Folders ....................................................................................................................404 Creating folders in the FeatureManager ..................................................................404 Adding items to existing folders ..............................................................................405 Reordering items in the tree ....................................................................................406 Working with Tree Display Options ..................................................................................406 Show feature names and descriptions ......................................................................407 Show component and config names and descriptions..............................................407 Viewing features, mates, and dependencies ............................................................409 Tutorial: Managing the FeatureManager ............................................................................411 Summary ..........................................................................................................................411
xii
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xiii
Contents
Chapter 13: Getting More from Mates . . . . . . . . . . . . . . . . . . . . 413 Applying Mates ................................................................................................................414 Mating through the Mate PropertyManager..............................................................414 SmartMates..............................................................................................................417 Mating with macros ................................................................................................420 Mating for Motion ............................................................................................................420 Degree-Of-Freedom analysis....................................................................................420 Best bet for motion ..................................................................................................421 Working with Advanced Mate Types..................................................................................423 Symmetric mate ......................................................................................................424 Cam mate ................................................................................................................424 Width mate ............................................................................................................425 Gear mate ................................................................................................................426 Rack and Pinion mate..............................................................................................426 Limit mates..............................................................................................................426 Belt/Chain ..............................................................................................................428 Editing and Troubleshooting ............................................................................................428 Editing existing mates..............................................................................................428 Troubleshooting ......................................................................................................430 Distinguishing between the Warnings and the Errors ..............................................430 Examining Mate Options ..................................................................................................432 Summarizing Mate Best Practices ......................................................................................432 Tutorial: Mating for Success ..............................................................................................433 Summary ..........................................................................................................................438
Chapter 14: Assembly Configurations and Display States . . . . . . . . . . 439 Using Display States ..........................................................................................................439 Display States and configurations ............................................................................440 Display States and drawings ....................................................................................442 Understanding Assembly Configurations ..........................................................................443 Configurations for performance ..............................................................................443 Configurations for positions ....................................................................................448 Configurations for product variations ......................................................................451 Design tables for assembly configurations................................................................452 Assembly configuration dos and don’ts....................................................................453 Creating Exploded Views ..................................................................................................453 Tutorial: Working with Assembly Configurations ..............................................................460 Summary ..........................................................................................................................464
Chapter 15: Component Patterns . . . . . . . . . . . . . . . . . . . . . . . 465 Using Local Component Patterns ......................................................................................466 Local pattern references ..........................................................................................466 Using Derived Component Patterns ..................................................................................469 Understanding Other Pattern Options ..............................................................................470 Dissolve Pattern ......................................................................................................471 Add to new folder....................................................................................................471
xiii
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xiv
Contents
Component pattern display options ........................................................................471 Component patterns and configurations..................................................................471 Tutorial: Creating Component Patterns..............................................................................472 Summary ..........................................................................................................................473
Chapter 16: Modeling in Context . . . . . . . . . . . . . . . . . . . . . . . 475 Understanding In-Context Design ....................................................................................475 Advantages of in-context modeling..........................................................................476 Potential problems with in-context modeling ..........................................................476 Dealing with the Practical Details of In-Context Modeling ................................................476 The in-context process ............................................................................................477 In-context best practice suggestions ........................................................................485 Other Types of External References....................................................................................493 Inserted parts ..........................................................................................................493 Split parts ................................................................................................................494 Mirror parts ............................................................................................................494 Tutorial: Working In-Context ............................................................................................494 Summary ..........................................................................................................................500
Part IV: Creating and Using Libraries
501
Chapter 17: Using Hole Wizard and Toolbox . . . . . . . . . . . . . . . . . 503 Using the Hole Wizard ......................................................................................................503 Anatomy of a Hole Wizard hole ..............................................................................505 2D versus 3D placement sketches............................................................................506 Making and using Favorites ....................................................................................510 Using the Hole Series ..............................................................................................512 Comprehending Toolbox ..................................................................................................515 How Toolbox works ................................................................................................515 Toolbox in a multi-user environment ......................................................................523 Toolbox administration............................................................................................525 Using Toolbox ........................................................................................................532 Organizing Toolbox parts in an assembly ................................................................537 Recommendations ..................................................................................................537 Tutorial: Gaining Experience with the Hole Wizard and Toolbox ......................................538 Summary ..........................................................................................................................547
Chapter 18: Working with Library Features. . . . . . . . . . . . . . . . . . 549 Using Library Features ......................................................................................................549 Getting started with library features ........................................................................550 The Library Feature interface ..................................................................................550 Other Design Library functions ..............................................................................554 Creating Library Features ..................................................................................................557 Creating a library feature ........................................................................................557 Creating a library feature from an existing part ........................................................562 Adding folders to the library ..................................................................................564
xiv
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xv
Contents
Tutorial: Working with Library Features ............................................................................564 Summary ..........................................................................................................................570
Chapter 19: Using Smart Components . . . . . . . . . . . . . . . . . . . . 571 Understanding Smart Components ..................................................................................571 Using Smart Components..................................................................................................572 Getting started with a simple Smart Component ....................................................572 Auto-sizing Smart Components ..............................................................................575 Making Smart Components ..............................................................................................577 Getting started with a simple Smart Component ....................................................577 Creating an auto-sizing Smart Component ..............................................................580 File management with Smart Components ..............................................................585 Editing Smart Components......................................................................................586 Tutorial: Working with Smart Components ......................................................................587 Summary ..........................................................................................................................590
Part V: Creating Drawings
591
Chapter 20: Automating Drawings: The Basics . . . . . . . . . . . . . . . . 593 The Difference between Templates and Formats ................................................................593 Can templates be changed?......................................................................................594 Why have different templates or formats? ................................................................594 Creating Drawing Formats ................................................................................................595 Customizing an existing format ..............................................................................595 Creating a format from a blank screen ....................................................................601 Creating a format from an imported DWG/DXF file ................................................602 Saving the format ....................................................................................................605 Second sheet formats ..............................................................................................605 Creating Drawing Templates..............................................................................................606 Using predefined views in drawing templates ..........................................................606 Using favorites and blocks in templates ..................................................................610 Custom properties in templates ..............................................................................611 Saving a template ....................................................................................................612 Creating Blocks ................................................................................................................613 Summary ..........................................................................................................................613
Chapter 21: Working with Drawing Views . . . . . . . . . . . . . . . . . . 615 Creating Common View Types ..........................................................................................616 Using the View palette ............................................................................................616 Named ....................................................................................................................617 Projected view ........................................................................................................620 Standard 3 view ......................................................................................................621 Detail view ..............................................................................................................621 Section view ............................................................................................................623
xv
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xvi
Contents
Creating Other View Types ................................................................................................627 Crop view................................................................................................................627 Broken-out Section view..........................................................................................628 Break view ..............................................................................................................632 Auxiliary view ........................................................................................................633 Alternate Position view ............................................................................................634 Predefined view ......................................................................................................635 Empty view ............................................................................................................635 Custom view ..........................................................................................................635 Relative view ..........................................................................................................636 3D Drawing View Mode ..........................................................................................636 View orientation and alignment ..............................................................................637 Using Display Options in Views ........................................................................................638 Display States ..........................................................................................................638 Display modes ........................................................................................................639 Edge display options ..............................................................................................640 View quality settings................................................................................................641 Distinguishing Views from Sheets......................................................................................642 Tutorial: Working with View Types, Settings, and Options ................................................642 Summary ..........................................................................................................................649
Chapter 22: Using Annotations and Symbols . . . . . . . . . . . . . . . . . 651 Using Notes ......................................................................................................................651 The workflow for placing notes ..............................................................................651 Fonts ......................................................................................................................652 Text boxes and wrapping ........................................................................................652 Notes and leaders ....................................................................................................653 Favorites..................................................................................................................656 Linking notes to custom properties..........................................................................657 Hyperlinking text ....................................................................................................657 Notes and symbols ..................................................................................................658 Using Blocks ....................................................................................................................658 Inserting blocks ......................................................................................................659 Creating blocks........................................................................................................661 Editing blocks ........................................................................................................662 Using Symbols ..................................................................................................................663 Where can you use symbols? ..................................................................................663 Custom symbols ......................................................................................................664 Using Center Marks and Centerlines ................................................................................664 Tutorial: Using Annotations ..............................................................................................666 Summary ..........................................................................................................................668
xvi
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xvii
Contents
Chapter 23: Dimensioning and Tolerancing. . . . . . . . . . . . . . . . . . 669 Putting Dimensions on Drawings ......................................................................................669 Insert Model Items ..................................................................................................670 Using reference dimensions ....................................................................................672 Dimension Options ..........................................................................................................676 Adding Tolerances ............................................................................................................681 Precision..................................................................................................................682 Geometric Tolerancing ............................................................................................682 Using Dimension Favorites................................................................................................682 Tutorial: Working with Dimensions and Tolerances ..........................................................683 Summary ..........................................................................................................................686
Chapter 24: Working with Tables and Drawings . . . . . . . . . . . . . . . 687 Driving the Bill of Materials ..............................................................................................687 SolidWorks table-based BOM ..................................................................................688 Excel-based BOM ....................................................................................................695 Using Design Tables ..........................................................................................................696 Using Hole Tables..............................................................................................................698 Using Revision Tables........................................................................................................701 Using Gauge Tables and Bend Tables ................................................................................703 Using Weldment Cut List Tables........................................................................................703 Using General Tables ........................................................................................................704 Tutorials: Using Tables ......................................................................................................704 Using BOMs ..........................................................................................................704 Using Hole Tables....................................................................................................708 Using Revision Tables ..............................................................................................710 Summary ..........................................................................................................................711
Chapter 25: Using Layers, Line Fonts, and Colors . . . . . . . . . . . . . . 713 Controlling Layers ............................................................................................................714 Layers in imported 2D data ....................................................................................714 Layers on the sheet format ......................................................................................715 Dimensions and notes on layers ..............................................................................716 Components on layers ............................................................................................716 Controlling Line Format....................................................................................................717 Using the Line Format settings ................................................................................718 End Cap Style..........................................................................................................718 Line Thickness settings............................................................................................718 Line Style setting ....................................................................................................719 Color Display mode ................................................................................................719 Hiding and Showing Edges ..............................................................................................720 Tutorial: Using Drawing Display Tools ..............................................................................720 Summary ..........................................................................................................................723
xvii
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xviii
Contents
Part VI: Using Advanced Techniques
725
Chapter 26: Modeling Multibodies . . . . . . . . . . . . . . . . . . . . . . 727 With Great Power Comes Great Responsibility ..................................................................728 Multibody modeling is not assembly modeling........................................................728 Appropriate multibody uses ....................................................................................729 Understanding Multibody Techniques ..............................................................................730 Complex shapes across bodies ................................................................................731 Tool bodies and Boolean operations ........................................................................733 Local operations ......................................................................................................737 Patterning................................................................................................................739 Simplifying very complex parts ..............................................................................741 Bridge between solids ..............................................................................................743 Undetermined manufacturing methods ..................................................................744 Creating Multibodies ........................................................................................................745 Disjoint sketches ....................................................................................................745 Merge Result option ................................................................................................745 Feature Scope ..........................................................................................................746 Cut feature ..............................................................................................................748 Split feature ............................................................................................................748 Insert Part feature ....................................................................................................751 Managing Bodies ..............................................................................................................752 Body folders ............................................................................................................752 Hide or show bodies................................................................................................754 Deleting bodies........................................................................................................755 Renaming bodies ....................................................................................................755 Tutorials: Working with Multibodies ................................................................................755 Merging and local operations ..................................................................................756 Splitting and patterning bodies................................................................................757 Summary ..........................................................................................................................760
Chapter 27: Working with Surfaces . . . . . . . . . . . . . . . . . . . . . . 761 Why Do You Need Surfaces? ............................................................................................762 Understanding Surfacing Terminology ..............................................................................762 Knit ........................................................................................................................762 Trim ........................................................................................................................763 Untrim ....................................................................................................................763 Hybrid modeling ....................................................................................................764 NURBS ....................................................................................................................764 Developable surface ................................................................................................765 Ruled surface ..........................................................................................................766 Gaussian curvature ..................................................................................................766
xviii
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xix
Contents
What Surface Tools Are Available? ....................................................................................766 Extruded Surface ....................................................................................................766 Revolved Surface ....................................................................................................767 Swept Surface ..........................................................................................................767 Lofted Surface..........................................................................................................767 Boundary Surface ....................................................................................................767 Offset Surface ..........................................................................................................769 Radiate Surface ........................................................................................................770 Knit Surface ............................................................................................................771 Planar Surface..........................................................................................................772 Extend Surface ........................................................................................................773 Trim Surface ............................................................................................................774 Fill Surface ..............................................................................................................774 Mid-surface ............................................................................................................776 Replace Face............................................................................................................777 Untrim Surface ........................................................................................................778 Parting Surface ........................................................................................................779 Ruled Surface ..........................................................................................................779 Using Surfacing Techniques ..............................................................................................780 Up to Surface/Up to Body........................................................................................781 Cut With Surface ....................................................................................................782 Replace Face............................................................................................................783 Fill Surface in action................................................................................................784 Memory surface ......................................................................................................785 Molds ......................................................................................................................786 Tutorial..............................................................................................................................788 Using Cut With Surface ..........................................................................................788 Using Offset Surface ................................................................................................789 Using Fill Surface blend ..........................................................................................792 Summary ..........................................................................................................................796
Chapter 28: Master Model Techniques . . . . . . . . . . . . . . . . . . . . 797 Using Pull Functions ........................................................................................................798 Insert Part................................................................................................................798 Insert Into New Part ................................................................................................801 Using Push Functions........................................................................................................801 Split feature ............................................................................................................802 Save Bodies..............................................................................................................803 Tutorial: Working with Master Model Techniques..............................................................804 Insert Part................................................................................................................804 Insert Into New Part ................................................................................................806 Split ........................................................................................................................807 Save Bodies..............................................................................................................808 Summary ..........................................................................................................................809
xix
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xx
Contents
Part VII: Working with Specialized Functionality
811
Chapter 29: Using the Base Flange Method for Sheet Metal Parts . . . . . 813 Understanding the Big Picture ..........................................................................................814 Using the Base Flange Features..........................................................................................815 Base Flange /Tab feature ..........................................................................................815 Sheet Metal feature ..................................................................................................816 Flat Pattern feature ..................................................................................................822 Edge Flange feature ................................................................................................824 Miter Flange feature ................................................................................................829 Hem feature ............................................................................................................831 Jog feature ..............................................................................................................831 Sketched Bend feature ............................................................................................833 Closed Corner feature..............................................................................................834 Corner Trim and Break Corner features ..................................................................836 Forming Tool feature ..............................................................................................838 Lofted Bends feature ................................................................................................842 Unfold and Fold features ........................................................................................843 Flatten command ....................................................................................................843 Tutorial: Using the Base Flange Sheet Metal Method..........................................................844 Summary ..........................................................................................................................849
Chapter 30: Using the Insert Bends Method for Sheet Metal Parts . . . . . 851 Architecture of Insert Bends ..............................................................................................852 Making Sheet Metal from a Generic Model ........................................................................853 Normal Cut ............................................................................................................853 Rip feature ..............................................................................................................854 Sheet Metal feature ..................................................................................................855 Flatten Bends feature ..............................................................................................855 Process Bends feature ..............................................................................................856 No Bends ................................................................................................................857 Flat Pattern..............................................................................................................857 Working with Imported Geometry ....................................................................................858 Making Rolled Conical Parts..............................................................................................858 Mixing Methods ................................................................................................................860 Tutorial: Working with the Insert Bends method for sheet metal parts ..............................860 Summary ..........................................................................................................................863
Chapter 31: Using Weldments . . . . . . . . . . . . . . . . . . . . . . . . . 865 Sketching in 3D ................................................................................................................865 Navigating in space..................................................................................................866 Sketch relations in 3D sketches ..............................................................................867 Planes in space ........................................................................................................868 Planar path segments ..............................................................................................870 Dimensions ............................................................................................................870
xx
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xxi
Contents
Using the Weldment Tools ................................................................................................870 Weldment................................................................................................................871 Structural Member ..................................................................................................871 Trim/Extend ............................................................................................................877 End Cap ..................................................................................................................879 Gusset ....................................................................................................................879 Fillet Bead ..............................................................................................................880 Using Non-Structural Components ..................................................................................881 Using Sub-Weldments ......................................................................................................882 Using Cut Lists..................................................................................................................882 Creating Weldment Drawings............................................................................................884 Tutorial: Working with Weldments....................................................................................886 Summary ..........................................................................................................................893
Chapter 32: Creating and Using Macros . . . . . . . . . . . . . . . . . . . 895 Recording Macros..............................................................................................................896 Recording a rectangle-sketching macro....................................................................896 Replaying the macro ................................................................................................899 Creating a Macro with a User Form ..................................................................................902 Building the Form ............................................................................................................903 Finding Macro Help ..........................................................................................................906 Summary ..........................................................................................................................906
Part VIII: Appendixes
907
Appendix A: Implementing SolidWorks . . . . . . . . . . . . . . . . . . . . 909 Appendix B: Tools, Options . . . . . . . . . . . . . . . . . . . . . . . . . . 931 Appendix C: Finding Help . . . . . . . . . . . . . . . . . . . . . . . . . . 1007 Appendix D: What’s on the CD-ROM . . . . . . . . . . . . . . . . . . . . 1015
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1017
xxi
02_080139 ftoc.qxp
3/26/07
3:17 PM
Page xxii
03_080139 fpref.qxp
3/26/07
3:18 PM
Page xxiii
W
elcome to the SolidWorks 2007 Bible. This book has been written as a desk reference for beginning and intermediate SolidWorks users. SolidWorks is such an immense software program that trying to cover all of its functions is an extremely ambitious undertaking, and I know that a few have been left out. Because of the scope of the topic, I have limited the book to covering the basic SolidWorks package, without the Office, Office Professional, or Office Premium add-ins, although I have devoted half of a chapter to Toolbox. You will find enough information here that the book can grow with your SolidWorks needs. I have written tutorials for most of the chapters with newer users in mind, because for them it is most helpful to see how things are done in SolidWorks step by step. The longer narrative examples give more in-depth information about features and functions, as well as the results of various settings and options. I have included an extensive appendix covering the Tools, Options settings. This offers an in-depth explanation of each option, including both System Options and Document Properties. This appendix uses special symbols to identity items that are new for SolidWorks 2007 or that affect file size or speed.
Icons This book uses a set of icons to point out certain details in the text. While they are relatively selfexplanatory, here is what each of these icons indicates:
NOTE
Notes highlight useful information that you should take into consideration, or an important point that requires special attention.
TIP
Tips provide you with additional advice that makes the software quicker or easier to use.
CAUTION
Caution icons warn you of potential problems before you make a mistake.
NEW FEATURE
The New Feature icon highlights features and functions that are new to SolidWorks 2007.
CROSS-REF
Cross-Ref icons point out where you can find additional information about a topic elsewhere in the book.
ON the CD-ROM
This icon points you toward related material on the book’s CD.
xxiii
03_080139 fpref.qxp
3/26/07
3:18 PM
Page xxiv
Preface
The SolidWorks 2007 Bible is unique in its use of these two icons:
BEST PRACTICE
Best practice icons point out recommended settings or techniques that are safe in most situations.
PERFORMANCE
Performance icons elaborate on how certain settings, features, or techniques affect rebuild speed or file size.
These icons point out and describe techniques and settings that are either recommended or not recommended for specific reasons. Best Practice is usually considered to be very conservative usage, where the stability of the parametrics and performance (a euphemism for rebuild speed) are the ultimate goals. These two aspects of SolidWorks models are usually weighed against modeling speed (how long it takes you to create the model). Best Practice and Performance recommendations need to be taken seriously, but you should treat them as guidelines rather than as rules. When it comes right down to it, the only hard and fast rule about SolidWorks is that there are no hard and fast rules. In fact, I believe that the only reason to have rules in the first place is so that you know when you can break them. Parametric stability and modeling speed are not always the ultimate goals, and are often overridden when workaround techniques are used simply to accomplish a geometric goal. Because not everyone models with the same goals in mind, a single set of rules can never apply for everyone. You must take the best practice suggestions and apply them to your situation using your own judgment. My point of view while writing this book has been that of someone who is actually using the software, not of someone trying to sell ideas, nor of someone trying to make the software look good. I try to approach the software objectively as a tool, recognizing that complex tools are good at some things and not so good at others. Both kinds of information (good and not-so-good) are useful to the reader. Pointing out negatives in this context should not be construed as criticizing the SolidWorks software, but rather as preparing the reader for real-world use of the software. Any tool this complex is going to have imperfections. Hopefully some of my enthusiasm for the software also shows through and is to some extent contagious.
Terminology An important concept referred to frequently in SolidWorks is design intent. As a practical matter, I use the phrase design for change to further distinguish design intent from other design goals. The reader needs to be familiar with some special terminology before continuing. In many cases, a SolidWorks vernacular or slang is used when the official terminology is either not descriptive enough or, as is sometimes the case, has multiple meanings. For example, the word shortcut has multiple meanings in the SolidWorks interface. It is used to describe right mouse button menus as well as hotkeys. As a result, I have chosen not to use the word shortcut and instead substitute the words RMB and hotkey.
xxiv
03_080139 fpref.qxp
3/26/07
3:18 PM
Page xxv
Preface
I frequently use RMB to refer to Right Mouse Button menus, or other data that you access by clicking the right mouse button on an item. The word tree refers to the list of features in the FeatureManager. Also, command and option names are referred to using all initial capitals, even when SolidWorks does not use the same capitalization. For example, the setting Single Command Per Pick is listed in Tools ➪ Options as Single command per pick. Differences are frequently found between the names of features on toolbars and the names in the menus or PropertyManager titles. In these cases, the differences are usually minor, and either name may be used. Most functions in SolidWorks can work with either the object-action or the action-object scenarios. These are also called pre-select and select, respectively. For example, the Hole Wizard is one tool for which pre-selection is definitely recommended because a difference in functionality is seen between pre-selection and selection. The Fillet feature shows no difference between using preselection and selection. Most features allow pre-selection, and some functions, such as inserting a design table, require pre-selection. Although you cannot identify a single rule that covers all situations, most functions accept both. Frequently in this book, I have suggested enhancement requests that the reader may want to make. This is because SolidWorks development is driven to a large extent by customer requests, and if a large number of users converge on a few issues, then those issues are more likely to be fixed or changed. Again, the enhancement request suggestions are not made to criticize the software, but to make it better. I hope that several of you will join me in submitting enhancement requests. SolidWorks is an extremely powerful modeling tool, very likely with the best combination of power and accessibility on the MCAD market today. This book is meant to help you take advantage of its power in your work and even hobbyist applications. If I could impart only a single thought to all readers of this book, it would be that with a little curiosity and some imagination, you can begin to access the power of SolidWorks for geometry creation and virtual product prototyping. You should start with the assumption that there is a way to do what you are imagining, and that you should be open to using different techniques. For AutoCAD users making the transition to SolidWorks, you should simply forget everything you know about AutoCAD, because most of it, except for the most general geometric concepts, will not apply to SolidWorks, and will often simply confuse you. Whoever you are, I hope that you find insight deeper than simply “what does this button do?” in this book. I hope that you will find an intuition for thinking like the software. Jeff Ray of the SolidWorks Corporation has said that the goal is to make the software as “intuitive as a light switch.” While most people will agree that they have some work left to achieve that particular goal, I believe that approaching the interface intuitively, rather than attempting to remember it all by rote, is the best method. Good luck to you all.
xxv
03_080139 fpref.qxp
3/26/07
3:18 PM
Page xxvi
04_080139 flast.qxp
3/26/07
3:19 PM
Page xxvii
T
he ideas that go into a book of this size do not all originate with a single individual. Research for many of the topics was done at user group meetings, the newsgroup comp.cad.solidworks, SolidWorks Corporation’s discussion forums, and SolidWorks Customer Portal, as well as the Web sites of many individuals. I would like to thank all of the individuals who have posted to the public forums or created personal Web sites. Many of these people have knowingly or unknowingly contributed to my SolidWorks education, as well as that of many other SolidWorks users around the world. I would especially like to thank Richard Doyle, the technical editor for this book, for keeping me on the straight and narrow when possible. This would not have been possible without Marty Minner and Courtney Allen, Wiley editors who with great patience have provided guidance and advice as necessary. Thanks also to those who have encouraged me along the way, including Kim Hardy, Chris Cole, Stan Kujawski, and the guys from Spark Engineering.
xxvii
04_080139 flast.qxp
3/26/07
3:19 PM
Page xxviii
05_080139 pt01.qxp
3/26/07
3:20 PM
Page 1
SolidWorks Basics IN THIS PART Chapter 1 Getting Familiar with SolidWorks Chapter 2 Navigating the SolidWorks Interface Chapter 3 Getting Started with SolidWorks Chapter 4 Working with Sketches Chapter 5 Creating Simple Parts, Assemblies, and Drawings
05_080139 pt01.qxp
3/26/07
3:20 PM
Page 2
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 3
Getting Familiar with SolidWorks
L
et’s face it; people develop brand loyalty to CAD software programs. It sounds silly, but you know it’s true. If you are coming to SolidWorks from another CAD program, you are probably feeling a level of unease that is proportional to the amount of time you spent using the other program. You will get past that, and everything will be fine, I promise. As you will see, SolidWorks does everything as well as, or better than, your old software, and you will never crave your old software after you drink this Kool-Aid. The biggest hurdle that many users face in learning a new CAD program is letting go of the old one. In some cases, the old software helps you to understand the new one, but in others, the thinking is just too different, and you may need to forget everything you thought you knew about CAD. Switching to SolidWorks can involve a little of both. For example, if you are coming from Inventor, Solid Edge, or another program in that class, you will find SolidWorks to be very familiar territory, with a similar if not identical design philosophy. SolidWorks also shares a lot of underlying structure with Pro/ENGINEER, and if you are coming from that product, there will be some relearning, but much of your training will be transferable. If you are coming from 2D AutoCAD, SolidWorks may at first cause a bit of culture shock for you. However, after you accept the concept that getting the model correct is dependent on the process, things will go more easily. As you will see, SolidWorks, and in fact most solid modeling in general, is very process-based. SolidWorks is also a very Windows-based software, and so if you are familiar with Windows conventions, then you already know a lot about the SolidWorks interface and shortcuts. The regular and context-sensitive menus, toolbars, and keyboard shortcuts, as well as many other interface elements, all work the same as they do in Word, Excel, or PowerPoint. OS X and Linux users should not hold
3
IN THIS CHAPTER Understanding feature-based modeling Understanding history-based modeling Sketching with parametrics Understanding Design Intent Editing Design Intent Working with associativity
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 4
SolidWorks Basics
their breath for SolidWorks to be ported to those operating systems, although there have been thirdparty developments that allow Windows software to run on other operating systems and hardware. In any case, regardless of how you arrived here with this SolidWorks Bible in your hand, here you are. Together we will progress from basic concepts to advanced techniques, everyday settings, and subtle nuances. This book will serve as your friend, tutor, and desk reference for learning about SolidWorks software.
Understanding Feature-Based Modeling There is some terminology that you need to come to grips with before we dive into building models with SolidWorks. Notice that I talk about “modeling” rather than “drawing.” This is because SolidWorks is really virtual prototyping software. Whether you are building an assembly line for automotive parts or designing decorative perfume bottles, SolidWorks can help you visualize your product in the most realistic way possible without actually having it in your hand. This is more akin to making a physical model in the shop than drawing on paper. “Feature-based” modeling means that you build the model by incrementally identifying functional shapes, and applying processes to create the shapes. For example, you can create a simple box by using the Extrude process, and you can create a sphere by using the Revolve process. However, you can make a cylinder by using either process, by revolving a rectangle or extruding a circle. You start by visualizing the 3D shape, and then apply a process to a 2D sketch to create that shape. This concept on its own is half of what you need to know to create models with SolidWorks. Figure 1.1 shows images of simple feature types with the 2D sketches from which they were created. Many different feature types in SolidWorks enable you to create everything from the simplest geometry shown above to free-form shapes. In general, when I talk about modeling, I am talking about solid modeling, although SolidWorks also has a complete complement of surfacing tools. I will discuss the distinction between solid and surface modeling in a later chapter. Table 1.1 lists some of the most common features that are found in SolidWorks, and classifies them according to whether they always require a sketch, a sketch is optional, or they never require a sketch. TABLE 1.1
Feature Types Sketch Required
Sketch Optional
No Sketch (Applied Features)
Extrude
Loft
Fillet
Revolve
Sweep
Chamfer
Rib
Dome
Draft
Hole Wizard
Shape
Shell
Wrap
Deform
Flex
4
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 5
Getting Familiar with SolidWorks
FIGURE 1.1 Simple extruded and revolved features
While the bulk of this book focuses on the use of solid features, I believe that no set of modeling tools is complete without surface-modeling functions. Hybrid features combine the use of solids and surfaces in some way, and are discussed in more detail in Chapter 27. The surfacing and hybrid features available in SolidWorks are: n Lofted surface n Swept surface n Fill surface n Boundary surface n Freeform surface n Offset surface n Knit surface n Radiate surface n Ruled surface n Replace Face n Trim surface
5
1
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 6
SolidWorks Basics
n Untrim surface n Cut with surface n Thicken surface n Cut Thicken surface In addition to these features, there are many other types that create reference geometry (such as curves, planes, and axes), or perform some operation on existing geometry.
Understanding History-Based Modeling In addition to being feature-based, SolidWorks is also history-based. To indicate process history, there is a panel to the left side of the SolidWorks window called the FeatureManager design tree. The FeatureManager keeps a list of the features in the order in which you have added them. It also enables you to reorder items in the tree (in effect, to change history). As a result, the order in which you perform operations is important. For example, consider Figure 1.2. This model was created by the following process: 1. Create a sketch. 2. Extrude the sketch. 3. Create a second sketch. 4. Extrude the second sketch. 5. Create a third sketch. 6. Extrude Cut the third sketch. 7. Apply fillets. 8. Shell the model.
If the order of operations used in the above part were slightly reordered, the resulting part would also look slightly different, as shown in Figure 1.3. Figure 1.4 shows a comparison of the FeatureManager design trees for the two different feature orders. You can reorder features by dragging them up or down the tree. Relationships between features can prevent reordering; for example, the fillets are dependent on the second extruded feature, and cannot be reordered before it. This is referred to as a Parent/Child relationship.
CROSS-REF
6
Reordering and Parent/Child relationships are discussed in more detail in Chapter 11.
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 7
Getting Familiar with SolidWorks
FIGURE 1.2 Features that are used to create a simple part
FIGURE 1.3 Using a different order of features for the same part
7
1
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 8
SolidWorks Basics
FIGURE 1.4 Compare the FeatureManager design trees for the parts from Figure 1.2 and Figure 1.3.
ON the CD-ROM
The part used for this example is available in the material from the CD-ROM, named Chapter 1 – Features.SLDPRT.
The order of operations, or history, is important to the final state of the part. For example, if you change the order so that the shell comes before the extruded cut, the geometry of the model changes, creating a sleeve inside instead of just a hole on top. You can try this for yourself by opening the part indicated above, dragging the Shell1 feature in the FeatureManager, and dropping it just above the Cut-Extrude1 feature. In some cases, reordering the features in the FeatureManager may result in geometry that might not make any sense; for example, if the fillets are applied after the shell, they might break through to the inside of the part. In these cases, SolidWorks gives an error that helps you to fix the problem. In 2D CAD programs where you are just drawing lines, the order in which you draw the lines does not matter, because the results are the same. This is one of the fundamental differences between history-based modeling and non-history-based drawing. Features are really just like steps in building a part; the steps can either add material or remove it. However, when you make a part on a mill or lathe, you are only removing material. The FeatureManager is like an instruction sheet to build the part. When you reorder and revise history, you change the final result.
8
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 9
Getting Familiar with SolidWorks
Sketching with Parametrics You have already seen that sketching is the foundation that underlies the most common feature types. We will now find that sketching in parametric software is vastly different from drawing lines in 2D CAD. Dictionary.com defines the word parameter as “one of a set of measurable factors . . . that define a system and determine its behavior and [that] are varied in an experiment.” What this means to us as SolidWorks users in a practical sense is that we can create sketches that change according to certain rules, and maintain relationships through those changes. This is the basis of parametric design. It extends beyond sketching to curve elements, surface features, and solid features. SolidWorks makes 2D and 3D sketching possible. Of the two methods, 2D sketches are by far the more widely used. You create 2D sketches on a selected plane, planar solid or surface face, and use them to establish shapes for features such as Extrude, Revolve, and others. Relations in 2D sketches are often created between sketch entities and other entities that may or may not be in the sketch plane. In situations where other entities are not in the sketch plane, the out-of-plane entity is projected into the sketch plane in a direction that is normal to the sketch plane. This does not happen for 3D sketches. You use 3D sketches for the Hole Wizard, piping, wiring, and weldments, among other applications such as complex shape creation. Both 2D and 3D sketches share some relation types, although some of these relations work differently in the two types of sketches. Some relations that are unique to each type of sketch. The available sketch relations are: n Along X, Along Y, Along Z: 3D sketch only. Along X means that the Y and Z coordinates do not change — only the X coordinates. This is similar for the other relations. n Intersection: 2D and 3D sketches. This relation is created by the Intersection Curve sketch tool. You cannot apply it manually. n Coincident: 2D and 3D sketches. In a 2D sketch, a point can be coincident with an entity that is not on the sketch plane because SolidWorks considers the external entity to be projected into the sketch plane. In a 3D sketch, the coincident relation is explicit rather than projected. n Concentric: 2D and 3D sketches. Available between arcs, circles, and ellipses, as well as items that project into a 2D sketch plane as arcs, circles, or ellipses. n Coradial: 2D and 3D sketches. This applies to arcs or circles that have the same center and radius. n Collinear: 2D and 3D sketches. Only available between a linear sketch entity and another linear sketch, edge, or curve entity. n Equal: 2D and 3D sketches. This is used to make lines of equal length or arcs and circles of equal radius.
9
1
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 10
SolidWorks Basics
n Equal Curvature: 2D and 3D sketches. This relation only applies to splines, although you can apply it between a spline and other sketch entities, edges, or curves. This is similar to Tangent, except that in addition to being tangent, the spline also matches the curvature of the other item at the end of the spline. The curvature value cannot be set explicitly for any sketch entity except in the form of an arc or circle radius. Curvature = 1/radius. n Fix: 2D and 3D sketches. This clamps a sketch entity wherever it is when you apply the relation. It is not considered best practice to make extensive use of the Fix relation. When it is used, it is a frequent cause of overdefined sketches and troubleshooting difficulties. n Horizontal: 2D and 3D sketches. Horizontal and vertical relations are relative to the local sketch origin, not the global part origin. When used in a 2D sketch, Horizontal is indicated by the short leg of the red sketch origin. When used in a 3D sketch, Horizontal can be applied only when sketching on a plane within the 3D sketch, and it has no relation to geometry outside the plane. n Midpoint: 2D and 3D sketches. An endpoint, sketch point, or centerpoint may be placed at the midpoint of a line or arc. In 3D sketches, only a line can receive a midpoint relation. n On Edge: 2D and 3D sketches. This relation is created by the Convert Entities sketch tool. You cannot apply it manually. n Parallel: 2D and 3D sketches. This may be used between sketch lines and linear edges, as well as curves or other sketch lines. When applied in a 2D sketch between a sketch line and an out-of-plane entity, the out-of-plane entity must project into the sketch plane as a straight line, and the parallel will apply to the projection. n Pierce: 2D sketch only. A sketch point, centerpoint, or endpoint can be pierced by an edge, curve, or sketch that is external to the sketch and out-of-plane. The point where the out-of-plane curve goes through the sketch plane is the pierce point. The out-of-plane entity is not projected into the sketch plane. It is the only 2D sketch relation that does not use projected out-of-plane entities. If the curve entity does not cross the sketch plane, the relation fails. If the curve crosses the sketch plane at more than one location, the pierce point becomes the closest crossing to the selected sketch point. n Symmetric: 2D sketch only. Symmetric relations are created by mirroring items around a sketch centerline, and you can also apply them manually to pre-existing sketch entities, by using a centerline for reference. n Tangent: 2D and 3D sketches. n Vertical: 2D and 3D sketches. Horizontal and vertical relations are relative to the local sketch origin, not the global part origin. When used in a 2D sketch, Vertical is indicated by the long leg of the red sketch origin. For planes in 3D sketches, horizontal and vertical relate only to the local plane, not to the 3D sketch origin. As a result, if a line is constrained to a plane in a 3D sketch, the plane is still allowed to rotate unless there is sketch geometry constrained to geometry outside of the sketch. n On Surface: 3D sketch only. Planar sketch entities such as lines and arcs in a 3D sketch can be given the On Surface relation to planes or planar faces. Sketch points can be given
10
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 11
Getting Familiar with SolidWorks
the relation to any surface type. The On Surface constraint is created automatically by the Spline On Surface sketch tool. n At Intersection Of Two Faces: 2D and 3D sketches. This sketch relation is only created by the Intersection Curve sketch tool, which draws sketch entities where surfaces, solid faces, or planes intersect. This relation cannot be created manually. For a simple example of working with sketch relations in a 2D sketch, consider the sketch that is shown in Figure 1.5. The only relationships between the four lines are that they form a closed loop that is touching end to end, and one of the corners is coincident to the part origin. The small square icon near the origin is the symbol for a coincident sketch relation. The setting to enable or disable these sketch relation symbols is found at View ➪ Sketch Relations.
FIGURE 1.5 A sketch of four lines
If you drag any of the unconstrained corners (except for the corner that is coincident to the origin), the two neighboring lines will follow the dragged endpoint, as shown in Figure 1.6. Notice the ghosted image left by the original position of the sketch. This is helpful when experimenting with changes to the sketch because you can see both the new and the old states of the sketch. The setting to enable or disable this ghosted position is found at Tools ➪ Options ➪ Sketch ➪ Ghost Image On Drag.
FIGURE 1.6 Dragging an endpoint
11
1
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 12
SolidWorks Basics
If you add a parallel relation between opposing lines, they now act differently, as shown in Figure 1.7.
FIGURE 1.7 Dragging an endpoint where lines have relations
Next, a second parallel and a horizontal relation are added, as shown in Figure 1.8. If you are following along by recreating the sketch on your computer, you will notice that one line has turned from blue to black.
FIGURE 1.8 Horizontal and parallel relations are added.
The colors represent sketch states. Sketch states include Underdefined, Overdefined, Fully Defined, Unsolvable, Zero Length, and Dangling. There can be entities with different states within a single sketch. Also, endpoints of lines can have a different state than the rest of the sketched entity. For example, a line that is sketched horizontally from the origin has a coincident at one endpoint to the origin, and the line itself is horizontal. As a result, the line and first endpoint are black, but the other endpoint is underdefined because the length of the line is not defined. Sketch states are indicated in the lower-right corner of the graphics window and also in the status bar. n Blue: Underdefined. The sketch entity is not completely defined. You can drag it to change size, position, or orientation. n Black: Fully Defined. The sketch entity is fully defined by a combination of sketch relations and dimensions. A sketch cannot be fully defined without being connected in some way to something external to the sketch, such as the part origin or an edge. Multiple external entities may be used, as appropriate. (The exception to this rule is the use of the Fix constraint, which, although effective, is not a recommended practice.)
12
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 13
Getting Familiar with SolidWorks
n Red: Overdefined. This can mean a number of things, but it is usually caused by conflicting relations or dimensions. For example, if a line has both horizontal and vertical relations, it becomes overdefined because one of the relations is satisfied, while the other is not. n Pink: Unsolvable. The difference between pink and red is that red is in one of several possible correct locations, whereas pink is not able to move to a correct location, generally because of another red entity. n Yellow: Zero Length. Solving the sketch relations would result in a zero-length entity; for example, this can occur where an arc is tangent to a line, and the centerpoint of the arc is also coincident to the line. n Brown: Dangling. The relation has lost track of the entity to which it was connected. Now you can see that dragging one corner only allows the lines to move in certain ways, as shown in Figure 1.9.
FIGURE 1.9 Sketch motion is becoming more constrained.
Dimensions are also part of the parametric scheme. If you apply an angle dimension about the origin and try dragging again, as shown in Figure 1.10, you see that the only aspect that is not locked down is the length of the sides. Notice also that when the angle dimension is added, another line turns black.
FIGURE 1.10 Open degrees of freedom can be dragged.
Finally, adding length dimensions for the unequal sides completes the definition of the sketch, as shown in Figure 1.11. At this point, all lines have turned black. This is the state that we call “fully defined.” Between the dimensions and sketch relations, there is enough information to recreate this sketch exactly.
13
1
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 14
SolidWorks Basics
It is considered best practice to fully define all sketches. However, there are times when this is not practical. When you create freeform shapes, generally through the use of splines, these shapes cannot easily be fully defined, and even if they are fully defined, the extra dimensions are usually meaningless, because it is impractical to dimension splines on manufacturing drawings.
BEST PRACTICE
FIGURE 1.11 The fully defined sketch cannot be dragged, and there are no degrees of freedom.
It is the idea of reacting to change that most concerns us regarding parametric design. There are other factors that can also drive the sketch, such as equations, other model geometry that is external to the sketch, and even geometry from another part in an assembly, as you shall see later.
Understanding Design Intent “Design Intent” is a phrase that you will hear SolidWorks users say a lot. I like to think of it as “design for change.” Design Intent means that when you put the parametric sketch relations together with the feature intelligence, you can build models that react to change in predictable ways. An example of Design Intent could be a statement in words that describes general aspects that help define the design of a part, such as “This part is symmetrical, with holes that line up with Part A, and thick enough to be flush with Part B.” From this description, and the surrounding parts, it is possible to recreate the part in such a way that if Part A or Part B changes, the part being described updates to match. There are some types of changes that cause features to fail or sketch relations to conflict. In most situations, SolidWorks has ample tools for troubleshooting and editing that allow you to either repair or change the model. In these situations, it is often the Design Intent itself that is changing. When editing or repairing relations, it is considered best practice to edit rather than delete. Deleting often causes additional problems further down the tree. Many users find it tempting to simply delete anything that has an error on it, but the cause of the error may be something other than what is identified.
BEST PRACTICE
14
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 15
Getting Familiar with SolidWorks
Editing Design Intent Design Intent is generally thought of as a static concept that controls changing geometry. However, this is not always the way things are. Design Intent often changes, thus requiring the way in which the model reacts to geometric changes to also change. Fortunately, SolidWorks has many tools to help you deal with situations like this.
View, Sketch Relations One of the most obvious tools necessary for visualizing existing Design Intent is to be able to see the sketch relations. You can show or hide icons that represent the relations using the menu selection View, Sketch Relations. View, Sketch Relations is an excellent candidate for use with a hotkey, thus allowing you to easily toggle the display on and off.
TIP CROSS-REF
For more information on creating and managing hotkeys, see Chapter 2.
You can use the sketch relation icons that are visible on the screen to delete relations by selecting the icon and pressing Delete on the keyboard. You can also use them to quickly tell the status of sketch relations, applying referring to the colors defined earlier.
Display/Delete Relations You can find the Display/Delete Relations tool on the Sketch toolbar or by selecting a sketch entity in an open sketch. The sketch status colors that were defined earlier also apply here, with the relations being shown in the appropriate color. (Relations are not shown in blue or black, only the colors that cause errors, such as red, yellow, pink, and brown.) This tool also allows you to group relations by several categories: n All in This Sketch n Dangling n Overdefining/Not Solved n External n Defined in Context n Locked n Broken n Selected Entities In the lower Entities panel, you can also replace one entity with another, or repair dangling relations.
15
1
06_080139 ch01.qxp
Part I
3/26/07
3:23 PM
Page 16
SolidWorks Basics
Suppressed Sketch Relations Suppressing a sketch relation means that the relation is turned off and not used to compute the position of sketch entities. Suppressed relations are generally used in conjunction with configurations.
CROSS-REF
Configurations are dealt with in detail in Chapter 10.
Working with Associativity Associativity in SolidWorks refers to links between documents, such as a part that has an associative link to a drawing. If the part changes, the drawing updates as well. Bi-directional associativity means that the part can actually be changed from the drawing. One of the implications of this is that you do not edit a SolidWorks drawing by simply moving lines on the drawing; you must change the model, which causes all views of the part or assembly to update correctly. Other associative links include using base parts, where one part is inserted as the first feature in another part. This might be the case when you build a casting. If the part is designed in its “as cast” state, it is then inserted into another part where machining operations are performed by cut features and the part is transformed into its “as machined” state. This technique is also used for plastic parts where a single shape spans multiple plastic pieces. A “master part” is created and split into multiple parts that could, for example, become a mouse cover and buttons. One of the most important aspects of associativity is file management. Associated files are kept connected by filenames. If a document name is changed, and one of the associated files does not know about the change, then the association between the files can become broken. For this reason, you should use SolidWorks Explorer to change names of associated files. There are other techniques that work, as well as some techniques that you should avoid. It is considered poor practice to change filenames of documents that are referenced by other documents with Windows Explorer. Links between parts, assemblies, and drawings can be broken in this way. Using SolidWorks Explorer or a Product Data Management, or PDM, application is the preferred method for changing filenames.
BEST PRACTICE
Summary Product development is about design, but it is even more about change. You actually design something once, but you may modify it endlessly (or it may seem that way sometimes). Similarly, SolidWorks is about design, but it really enables change. Think of SolidWorks as virtual prototyping software that allows you to change your prototype rather than having to make a new one. Virtual prototypes will never completely replace physical models, but they may reduce your dependence on them to some extent.
16
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 17
Getting Familiar with SolidWorks
SolidWorks is also about reusing data. Associativity allows you to model a part once and use it for Finite Element Analysis, or FEA, creating 2D drawings, building assemblies, creating photorealistic renderings, and so on. When you make changes to the model, your drawing is already updated, and you don’t have to reapply FEA materials and conditions or redo the rendering setup. Associativity saves you time by reusing your data. Associativity and change driven by feature-based and history-based modeling can take some getting used to if you have had limited exposure to it, but with some practice it becomes intuitive and you will see the many benefits for enabling change. Parametric sketching and feature creation help you to maintain Design Intent and also adjust it as necessary.
17
1
06_080139 ch01.qxp
3/26/07
3:23 PM
Page 18
07_080139 ch02.qxp
3/26/07
3:27 PM
Page 19
Navigating the SolidWorks Interface
T
he good news is that the SolidWorks interface is very flexible, and if you’re a Windows veteran, most of it is perfectly intuitive. The bad news is that there’s a lot of it to know. This chapter serves as a reference, and to help you decide how you want to use different portions of the interface. In this chapter, you learn how to effectively navigate and manipulate the interface, and you learn how to customize it both to suit your personal style and to help you work faster. This customization includes adding and removing toolbar buttons, displaying descriptions on toolbars, accessing dynamic help options, using standard and custom hotkeys, and making your interface customization portable to other computers. Many aspects of the SolidWorks interface are controlled by settings, which are covered in detail in Appendix B. Each interface element that is identified in Figure 2.1 is explained in greater detail in its own section of this chapter. Once you have mastered the various interface elements and customized your SolidWorks installation, working with the software becomes much more efficient and satisfying.
19
IN THIS CHAPTER Identifying elements of the SolidWorks interface Making the interface work for you Tutorial: Getting to know the interface
07_080139 ch02.qxp
Part I
3/26/07
3:27 PM
Page 20
SolidWorks Basics
FIGURE 2.1 Elements of the SolidWorks interface FeatureManager PropertyManager ConfigurationManager Display Pane expander arrows
Graphics window
CommandManager
SolidWorks Search
SolidWorks toolbars SolidWorks Resources Design Library File Explorer Search Results View Palette
Task pane
Display triad
Status bar
View orientation
Part origin Standard planes
Task pane expander arrows
Identifying Elements of the SolidWorks Interface When communicating with other users and tech support, it is important to use names for the various interface components that other people understand. This chapter is about learning the terminology and finding the tools that you need.
20
07_080139 ch02.qxp
3/26/07
3:27 PM
Page 21
Navigating the SolidWorks Interface
Toolbars The SolidWorks GUI (Graphical User Interface) is highly dependent on toolbar icons. While some icons are self-explanatory, others require some explanation. In this chapter, we discuss the Standard toolbar, button by button, in order to identify each of the available tools. Other toolbars have more specific functions and are explained in detail in their respective chapters.
Standard toolbar The Standard toolbar has many of the basic tools that are familiar to most Windows users. It is used for basic functions such as creating and saving documents, changing colors, and undoing and redoing actions. Although there may be some commands that new users are not familiar with, this section serves as a reference for all user levels; the more advanced commands are covered in their respective sections. The commands are shown in the order in which they appear on the Tools ➪ Customize ➪ Commands list for the Standard toolbar.
New The New command enables you to create new SolidWorks documents from existing templates. By default, SolidWorks uses the Novice interface for the New dialog box, which only allows you to select from default SolidWorks document templates, as shown in Figure 2.2.
FIGURE 2.2 The New SolidWorks Document dialog box, using the Novice interface
21
2
07_080139 ch02.qxp
Part I
3/26/07
3:27 PM
Page 22
SolidWorks Basics
You can click the Advanced button in the lower-left corner of the dialog box to switch to the Advanced interface. The difference between the Novice and Advanced interfaces is that the Advanced interface allows you to use additional tabs and custom templates. You can create additional tabs by using Windows Explorer to add folders to the folder that is indicated in Tools ➪ Options ➪ File Locations ➪ Document Templates. You can create custom templates by saving blank files with the desired settings as Template files, using the Files of type drop-down list in the Save As dialog box.
CROSS-REF
Templates are discussed in more detail in Chapter 3.
Figure 2.3 shows the Advanced interface of the New SolidWorks Document dialog box.
FIGURE 2.3 The New SolidWorks Document dialog box, using the Advanced interface
Open The Open command is used to open SolidWorks documents and to import other types of data. Although many new users look for an Import command in SolidWorks, you must actually import all data through the Open dialog box. You can also use the Open dialog box in many respects like a standard Windows Explorer window, because it enables you to copy, move, delete, and rename files. Figure 2.4 shows the Open dialog box.
22
07_080139 ch02.qxp
3/26/07
3:27 PM
Page 23
Navigating the SolidWorks Interface
FIGURE 2.4 The Open dialog box
The Preview option enables you to view document thumbnails in the Preview box that is located in the upper-right area of the Open dialog box. When you use the Advanced option with an assembly document, it brings up the Configure Document dialog box, shown in Figure 2.5, which enables you to: n Open the currently selected configuration. n Create a new assembly configuration with a specified name that shows all referenced models. n Create a new assembly configuration with a specified name that suppresses all parts in order to display only the assembly structure. (Suppressing all of the parts makes the assembly load instantly.). n Load the assembly using a specified part configuration name. For example, if you specify “Simplified,” the assembly opens all parts in their “Simplified” configuration, if it exists.
FIGURE 2.5 The Configure Document dialog box, which appears when you use the Advanced option in the Open dialog box
23
2
07_080139 ch02.qxp
Part I
3/26/07
3:27 PM
Page 24
SolidWorks Basics
You can open the following types of documents from the Open dialog box:
NOTE
The file types in the list are not alphabetized in the SolidWorks window, which makes it difficult to browse for file types. They are alphabetized here for ease of reference.
n ACIS (*.sat): ACIS files typically come from AutoCAD or CADKEY 3D models. n Add-Ins (*.dll): If you have applications that run through a dynamic link library, or DLL, then you can start the DLL from the Open command. n Adobe Illustrator (*.ai): You can open Adobe Illustrator files in SolidWorks as either sketch entities or sketch text. n CADKEY (*.prt, *.ckd): CADKEY files. n Catia Graphics (*.cgr): These are simply graphics files, not fully translated geometry files. n DWG (*.dwg): DWG files can be either 2D or 3D. It is best to use the DWG format to transfer only 2D files. Use the ACIS format to transfer AutoCAD 3D files. n DXF (*.dxf): DXF files can be either 2D or 3D. It is best to use the DXF format to transfer only 2D files. Use the ACIS format to transfer AutoCAD 3D files. n IDF (*.emn, *.brd, *.bdf, *.idb): These file types are used to transfer circuit-board data into SolidWorks. n IGES (*.igs, *.iges): IGES files can contain many types of information, but not all companies interpret it in the same way. SolidWorks works best with trimmed-surface IGES data. IGS data is sometimes used to transmit 2D data. SolidWorks does not typically do a good job of reading data in this format. You typically import 2D drawing data into SolidWorks as sketch entities. It is best to transfer 2D drawings as DWG or DXF files. Because of the variability of this data, it is not one of the preferred translation formats. n Inventor Part (*.ipt): SolidWorks can open Inventor files up to and including version 9.0; however, it interprets just the geometry, not a complete feature tree. n Library Features (*.lfp, *.sldlfp): Library features can include solid-feature geometry and sketches, and can also use configurations. These file formats are used for combinations of features that you use frequently, in order to save modeling time and to improve standardization. n Mesh (*.nxm, *.scn, *.3ds, *.obj, *.stl, *.wrl, *.ply, *.ply2): These are mesh formats that include STL and 3D Studio Max files, which can be used in ScanTo3D to create a surfaced-solid model. n Parasolid (*.x_t, *.x_b, *.xmx_txt, *.xmt_bin): There are two types of Parasolid files: binary and text. The binary files are typically about half the size of the text files, but you can read the text files with a text editor and extract certain information from the file header. SolidWorks is based on the Parasolid kernel, and so Parasolid is the preferred translation standard.
24
07_080139 ch02.qxp
3/26/07
3:27 PM
Page 25
Navigating the SolidWorks Interface
n Point Cloud (*.xyz, *.txt, *.asc, *.vda, *.igs): Point cloud files are typically brought in either for reference or to use ScanTo3D in order to create surfaced-solid models. n Pro/Engineer Part (*.prt, *.xpr): SolidWorks can read versions 17 to 2001 of Pro/Engineer parts, as well as Wildfire versions 1 and 2. n Pro/Engineer Assembly (*.asm, *.xas): SolidWorks can read versions 17 to 2001 of Pro/Engineer assemblies, as well as Wildfire versions 1 and 2. n Solid Edge Part (*.par): SolidWorks reads the Parasolid data from Solid Edge files. To transfer Solid Edge drawings, DWG or DXF formats are preferred. n Solid Edge Assembly (*.asm): SolidWorks reads the Parasolid data from Solid Edge files. To transfer Solid Edge drawings, DWG or DXF formats are preferred. n SolidWorks Parts, Assemblies, and Drawings (*.sldprt, *.sldasm, *.slddrw): These are native SolidWorks-created documents or imported data saved as SolidWorks file type. n STEP AP 203/214 (*.step, *.stp): STEP stands for “STandard for the Exchange of Product” model data. AP stands for “application protocol,” which signifies different types of STEP data. The number 203 indicates Configuration Controlled Design, and 214 indicates Core Data for Automotive Mechanical Design Processes. STEP is a reliable translation standard, although Parasolid is preferred. n STL (*.stl): STL is a tessellated or facetted format that is intended for the stereolithography process. You can import this format as a graphics body (with no selectable solid geometry), as a solid, or a surface. Keep in mind that because the data is tessellated, it cannot create smooth surfaces. Solid and surface imports severely degrade performance on any assembly into which they are placed. This is not a recommended format for import. n UGII (*.prt): Unigraphics 10 and higher, including NX parts, can be opened in SolidWorks. However, you should keep in mind that UG drawings and assemblies have the same extension, and do not open if there is no Parasolid data in the file. n VDAFS (*.vda): VDAFS is a German translation standard, which in my experience is at least as reliable as IGES. n VRML (*.wrl): VRML stands for “Virtual Reality Markup Language.” Its usage for CAD applications is limited, having been primarily a game geometry format. Large file sizes and tessellated geometry typically prevent its extensive use for transferring CAD data, but the format has special graduated color options that enable you to create 3D colored plots for analysis applications. This is not a recommended format for import.
Save The first time you save a document, the Save command acts like the Save As command, giving you the option to assign a path, filename, file type, and description. Figure 2.6 shows the Save As dialog box. After the first save, the command doesn’t display a dialog box, but just saves the data. You can specify whether or not to create backup copies by using the settings at Tools ➪ Options ➪ Backup/Recover.
25
2
07_080139 ch02.qxp
Part I
3/26/07
3:27 PM
Page 26
SolidWorks Basics
FIGURE 2.6 The Save As dialog box
In addition to its native formats, SolidWorks can also save the following types of documents: n 3D XML (*.3dxml): This is a new XML-based 3D display format that was created in 2005 by Microsoft and Dassault Systems for the integration of 3D images into documentation, Web sites, manuals, and other materials. n ACIS (*.sat): See the file-type description under the Open command list. n Adobe PDF (*.pdf): Prints the current document to a PDF file. n Catia Graphics (*.cgr): See the file-type description under the Open command list. n DWG (*.dwg): See the file-type description under the Open command list. n DXF (*.dxf): See the file-type description under the Open command list. n eDrawing (*.eprt, *.easm, *.edrw): eDrawing is a display-only format that you can publish either as a standalone file that requires a separate viewer, or with a viewer built into the actual file. It features a small file size (relative to full CAD documents) and allows the viewer to view in 3D, mark up, section, and move parts. n Form Tool (*.sldftp): This file type is specific to tools that form sheet metal. See Chapter 29 for more information. n IGES (*.igs): See the file-type description under the Open command list. n HCG (*.hcg): Catia Highly Compressed Graphics files. These files are display-only. n HOOPS HSF (*.hsf): HOOPS is a 3D graphics display format that is used by several 3D viewers.
26
07_080139 ch02.qxp
3/26/07
3:27 PM
Page 27
Navigating the SolidWorks Interface
n JPEG (*.jpg): SolidWorks saves out the display as a JPEG image. n Library Feature Part (*.sldlfp): See the file-type description under the Open command list. n Microsoft XAML (*.xaml): Extensible Application Markup Language is a language for creating graphical interfaces for Windows Presentation Foundation, or WPF. n Parasolid (*.x_t): See the file-type description under the Open command list. n Parasolid Binary (*.x_b): See the file-type description under the Open command list. n Part (*.sldprt): SolidWorks part format. n Part Template (*.prtdot): SolidWorks part-template format. See Chapter 3 for more information on templates. n Pro/Engineer (*.prt, *.asm): This file format does not save a feature-based part, but only a “dumb” solid. n ScanTo3D (*.xyz, *.wrl, *.stl, *.3ds): See the file-type description under the Open command list, listed under the Mesh and Point Cloud headings. n Tiff (*.tif): SolidWorks can save out the print image as a TIFF file. This is particularly useful for exporting high-resolution drawings. n Universal 3D (*.u3d): This is a 3D display format that is used by Adobe. n VDAFS (*.vda): See the file-type description under the Open command list. n VRML (*.wrl): See the file-type description under the Open command list.
Save All The Save All command saves all open documents. When saving a large number of files, settings can be important to avoid workflow interruption. One such setting, “Warn before saving documents with update errors,” is found at Tools ➪ Options ➪ General. Another such setting, “Warn about saving referenced documents,” is found at Tools ➪ Options ➪ External References.
Close This command closes the active document. You might also consider using Close All, which is found in the Window menu.
Reload One of the functions of the Reload command is the equivalent of closing the part without saving and reopening the same part. You can also use this command to change the read/write status of the file. The dialog box that displays also warns you when reloading causes you to discard changes, as shown in Figure 2.7.
27
2
07_080139 ch02.qxp
Part I
3/26/07
3:27 PM
Page 28
SolidWorks Basics
FIGURE 2.7 The Reload options
Check Read-Only Files This command becomes active only if the multi-user environment has been activated, and the option to check the status of read-only files has been activated in Tools ➪ Options ➪ Collaboration. If these conditions are met and you click this button, you either receive a message that says that none of the read-only files in memory have been changed, or if they have been changed, the Reload dialog box displays with the changed parts in the dialog box, prompting you to reload the parts with write access.
Make Drawing from Part/Assembly This command takes the current part or assembly and starts a new drawing, based on this part or assembly. How it behaves again depends on your settings. If you set the New dialog box to Novice, the Make Drawing command creates a new drawing of the active part or assembly from the default drawing template. If you set the New dialog box to Advanced, you are prompted to select a template. Again, depending on your setup, the automatically created drawing may behave differently. If you use a template that contains pre-defined views, the views are automatically populated. Whether the View Palette appears depends on the setting at Tools ➪ Options ➪ Drawings ➪ Show View Palette.
Make Assembly from Part/Assembly This tool works similarly to the Make Drawing tool in that if the New dialog box uses the Novice interface, it creates the new assembly from the default assembly template.
28
07_080139 ch02.qxp
3/26/07
3:27 PM
Page 29
Navigating the SolidWorks Interface
Another option that normally affects the function of this command is shown in Figure 2.8. The Make Assembly from Part/Assembly command opens a new assembly with the Insert Component PropertyManager dialog box open. The Start Command When Creating New Assembly option has no effect when you invoke a new assembly from the Make Assembly from Part/Assembly command. However, if you create a new assembly manually, this option controls whether or not the PropertyManager that selects models and places them in the assembly displays automatically.
FIGURE 2.8 The Insert Component dialog box opens when you apply the Make Assembly from Part/Assembly command.
Print The Print command in the Standard toolbar is different from the Print command in the File menu. The hotkey Ctrl+P accesses the Print command from the menu. The difference is that from the toolbar, the Print command automatically prints using the current document settings to the current document printer. Using the Print command from the Menu displays the Print dialog box and enables you to select the printer and settings.
Print Preview Print Preview displays a preview of what is to be printed. It allows you to zoom, but only with three limited zoom-scale options. These zoom options do not apply to printing, only to previewing. The Print button within the preview window takes you to the Print dialog box, where you can select settings and printers. The Print Selection option is available only for drawings, and must be selected from the Print dialog box. It is assumed that when a model is printed, the selection is in the graphics window, which is printed for model documents.
NOTE
29
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 30
SolidWorks Basics
Print3D Print3D takes you to a Web site that allows you to choose from one of several services to create a rapid prototype of the active part. This is different from 3D Printing, which is an option in the File menu that interfaces with 3D printer hardware that is connected to your computer.
Cut This command cuts the selected item and places it on the Clipboard. Consider using Delete if you do not intend to paste the cut item. You can also apply the Cut command by using the Ctrl+X hotkey. This is standard Windows functionality.
Copy This command copies the current selection to the Clipboard. The Copy command is also available by using the Ctrl+C hotkey. This is standard Windows functionality.
Paste This command pastes whatever is on the Clipboard to the currently selected location. Not all items can be placed this way. You can also apply the Paste command by using the Ctrl+V hotkey. This is standard Windows functionality.
Delete This command deletes the current selection. The Confirm Delete dialog box has some options that are shown in Figure 2.9. For example, the Also Delete Absorbed Features option deletes a feature and absorbed sketches. The Also Delete All Child Features option is not always available, but when it is, it automatically deletes dependent features. Turning this setting off causes dependent features to lose references, and to encounter dangling errors, but otherwise remain intact. The Delete command is also available in the right mouse button (RMB) menu and by using the Delete key on the keyboard.
FIGURE 2.9 The Confirm Delete dialog box
30
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 31
Navigating the SolidWorks Interface
There are two special uses of the Delete command. The first is when the selection is a surface or solid body. In this case, the Delete command results in a Delete Bodies feature being added to the FeatureManager, and the bodies being removed from the part. This is a history-based deletion, which means that if you roll back to before you used the Delete Bodies feature, the bodies are there again. The second special use is when the selection is a closed-loop open edge of a surface body (such as a circular hole that is trimmed in the middle of a surface, and not at the edge); SolidWorks asks if you are trying to delete the feature or to delete the hole. This is similar to the Untrim feature.
Undo The Undo command for SolidWorks 2007 allows you to undo more functions than in previous versions, but you may still encounter certain functions that it cannot undo. The drop-down arrow to the right of the icon enables you to see a list of how many functions it can undo. You can also access this function using the Ctrl+Z hotkey. This is standard Windows functionality.
Redo The Redo command enables you to redo actions that were undone with the Undo command. This command also has a drop-down list that shows all of the functions that you can redo. This is standard Windows functionality.
Rebuild The Rebuild command recalculates any features in the FeatureManager of the current part or assembly that SolidWorks has marked for rebuilding. When SolidWorks detects that a feature needs to be rebuilt, it displays a rebuild symbol next to the name of the feature in the FeatureManager. At times, a rebuild symbol may not disappear from a feature, forcing it to be rebuilt every time you make a change. In a component with a lot of features, this can create a serious performance problem.
NOTE
Other times, the rebuild symbol may not be present, even when features need to be rebuilt. Whenever it looks like something is wrong with a feature, it is a good idea to use the Forced Rebuild command, which rebuilds everything whether or not the software thinks that it is necessary. There is no icon or menu selection for Forced Rebuild; it is only available through the Ctrl+Q hotkey.
Options The Options icon displays the Tools ➪ Options settings dialog box, where most of the SolidWorks settings are located.
CROSS-REF
The Tools ➪ Options settings are explained in detail in Appendix B.
Properties The Properties button displays the PropertyManager. This is usually unnecessary if the Tools ➪ Options ➪ General ➪ Auto-show PropertyManager option is turned on.
31
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 32
SolidWorks Basics
Color The Color button displays the Color PropertyManager window. This enables you to assign colors, transparency, and other visual properties to parts, bodies, features, and faces.
TIP
When you are not sure at what level the color was applied (for example, face, feature, part, or component), you can use the Display pane and Display Callouts to identify col-
ored entities.
Materials You can apply materials to SolidWorks parts. These materials define characteristics for display, section hatching, density, and other material properties that are associated with Finite Element Analysis, or FEA. Materials with RealView graphics capabilities can look more realistic without rendering. Display properties are covered in more detail in Chapter 3.
Screen Capture The Screen Capture command copies the contents of the graphics window to the Clipboard.
Textures You can apply texture images to parts to improve the realism of the display without rendering.
Select Color Scheme The Select Color Scheme command enables you to toggle through all of the available color schemes one-by-one by clicking the button. You can also click the drop-down arrow, and select from a list of color schemes. If you want, you can also customize color schemes.
Select You can use the Select command to clear any other active tool, although you can also press the Esc button for the same purpose. Select activates the normal arrow cursor, which allows you to select items.
Selection Filter The Selection Filter command is a powerful tool that limits the selection to only certain types of entities. The F5 key toggles the display of the entire filter toolbar.
Web Toolbar The Web Toolbar button displays the Web toolbar, which enables you to open Web sites from within SolidWorks.
Full Screen The Full Screen command removes toolbars, menus, and the FeatureManager, displaying only the graphics window. You can also toggle this option using the F11 key. The F9 key toggles the display of the FeatureManager, and the F10 key toggles the toolbars.
32
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 33
Navigating the SolidWorks Interface
New Window The New Window command opens an additional window of the active document. This feature is different from using multiple viewports because the FeatureManager displays twice. This can be useful when there is a large list of features in the FeatureManager, and you want to see items at the top of the list as well as at the bottom.
Tile Horizontally The Tile Horizontally command tiles all open windows so that they are stacked one on top of another.
Tile Vertically The Tile Vertically command tiles all open windows so that they sit side-by-side.
Help The Help command accesses the SolidWorks Help file. Figures 2.10 to 2.25 show the most commonly used toolbars displaying their default icons. The SolidWorks interface uses over 500 icons. The Annotation toolbar, shown in Figure 2.10, contains tools for notes, balloons, surface finish and weld symbols, Geometric Dimensioning and Tolerancing (GD&T), datums, hole callouts, cosmetic threads, center marks and centerlines, cross hatch, and dimensioning. By default, this toolbar appears on the drawings Command Manager, but it may also be added to parts or assemblies as needed. These tools are covered in detail in Chapter 21.
FIGURE 2.10 The Annotation toolbar
The Assembly toolbar, shown in Figure 2.11, contains tools that are used in assemblies only. These include visibility tools, mating and moving tools, exploded-view tools, and various analysis tools, among others. These tools are covered in depth in Chapters 12 to 16.
FIGURE 2.11 The Assembly toolbar
33
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 34
SolidWorks Basics
The Dimensions/Relations toolbar, shown in Figure 2.12, contains tools for creating all of the dimension types in SolidWorks, including ordinate dimensions. In addition to the Sketch toolbar, you can also find tools for working with sketch relations.
FIGURE 2.12 The Dimensions/Relations toolbar
The Drawing toolbar, shown in Figure 2.13, contains tools for drawing view creation. You can also add buttons that do not display by default on the toolbar, including Empty View, Predefined View, and Update View. Update View is not a view type, but a command that updates all drawing views to the current state of the model. The tools on this toolbar are discussed thoroughly in Chapter 21.
FIGURE 2.13 The Drawing toolbar
By default, the Features toolbar, shown in Figure 2.14, contains the most commonly used solid features. Because there are a total of 47 feature commands, displaying them all on the toolbar is not practical. Everyone uses these features differently, and so you should customize your interface to match how you use the software. Surface features appear on a separate toolbar.
FIGURE 2.14 The Features toolbar
The Reference Geometry toolbar, shown in Figure 2.15, contains all of the available reference geometry tools. These include Plane, Axis, Coordinate System, Point, and Mate Reference.
34
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 35
Navigating the SolidWorks Interface
FIGURE 2.15 The Reference Geometry toolbar
The Selection Filter toolbar, shown in Figure 2.16, enables you to limit the selection to particular entity types. The filter works in conjunction with both manual selection and window selection.
FIGURE 2.16 The Selection Filter toolbar
The Sheet Metal toolbar, shown in Figure 2.17, contains all of the tools that are specific to sheet metal. Sheet Metal functionality is covered in detail in Chapters 29 and 30.
FIGURE 2.17 The Sheet Metal toolbar
The Sketch toolbar is the most frequently used toolbar in SolidWorks. Figure 2.18 shows the default sketch entities on the Sketch toolbar, but there are many other entities that do not appear on it and that you may want to use. These entities include Ellipse, Centerpoint Ellipse, Spline on Surface, Split Entities, and many more.
FIGURE 2.18 The Sketch toolbar
35
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 36
SolidWorks Basics
The SolidWorks Office toolbar, shown in Figure 2.19, displays buttons for each of the add-ins in SolidWorks Office. However, not all of the available add-ins appear by default on the toolbar. The add-ins are: n Photoworks: Photo-rendering software n Animator: Animation software that can work in conjunction with Photoworks n eDrawings: Collaboration software n 3D Instant Website: Enables you to post a 3D rotatable model to a Web site using a SolidWorks server n Toolbox: A library of hardware n Utilities: A suite of tools including: Compare Documents, Compare Features, Compare Geometry, Feature Paint, Find and Replace Annotations, Find/Modify/Suppress/Simplify, Format Painter, Geometry Analysis, Power Select, Report Manager, and Thickness Analysis n FeatureWorks: An add-in that helps you to parametrically rebuild imported parts n Design Checker: An add-in that checks aspects of a document against a standard Checks document n COSMOSWorks Designer: FEA application n COSMOSMotion: Motion analysis application n SolidWorks Routing: An add-in for piping, wiring, and tubing design n ScanTo3D: An add-in that enables you to take point cloud data and create parametric surface/solid models from it
FIGURE 2.19 The SolidWorks Office toolbar
The Standard toolbar, shown in Figure 2.20, is discussed in depth earlier in this chapter.
FIGURE 2.20 The Standard toolbar
36
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 37
Navigating the SolidWorks Interface
The Standard Views toolbar contains all of the orthogonal named views, as well as Isometric, Dimetric, and Trimetric. Standard Views also contains a button for Normal To, 2, and 4 viewports as well as the Link Views option. Figure 2.21 shows the Standard Views toolbar with the additional View Orientation button, which is part of the View toolbar. You can also access standard view icons through the View Orientation dialog box, which you can access using the View Orientation button or by pressing the Spacebar.
FIGURE 2.21 The Standard Views toolbar
The Surfaces toolbar, shown in Figure 2.22, contains mainly surface features. However, several non-surface features are also included in this toolbar by default. These features include Freeform and Fillet, which belong to the Features toolbar, and the Reference Geometry and Curves flyouts.
FIGURE 2.22 The Surfaces toolbar
The Tools toolbar, shown in Figure 2.23, contains tools such as Spell Check, Measure, Mass Properties, Section Properties, Check, Import Diagnostics, Feature Statistics, Equations, Deviation Analysis, Design Table, and COSMOSXpress.
FIGURE 2.23 The Tools toolbar
The View toolbar, shown in Figure 2.24, is one that you may use very frequently. In this toolbar, you can change the view from shaded to wireframe, rotate the view, or turn off plane display. You can do many things with the tools on this toolbar, and they are examined in detail in Chapter 3.
37
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 38
SolidWorks Basics
FIGURE 2.24 The View toolbar
SolidWorks Weldments are for creating welded frames, as well as tubular or structural components that are welded together. The Weldments toolbar has tools that are specifically intended for those functions. Figure 2.25 shows this toolbar.
FIGURE 2.25 The Weldments toolbar
Tooltips One way to learn about the individual icons is to use the Tooltips that appear after you hover your cursor over an icon for a few seconds. Tooltips come in two varieties, large and small. Large Tooltips show the name of the tool, along with a brief description of what it does. Small Tooltips show the tool’s name but not the description. To change the Tooltip display from large to small, or to turn off the Tooltip display altogether, you can use the Tools ➪ Customize menu option. In addition to the Tooltip balloons, tips also display in the status bar at the bottom of the screen when the cursor is over an icon. Figure 2.26 shows a comparison between large and small Tooltips.
FIGURE 2.26 SolidWorks uses large Tooltips by default, although it can also show small Tooltips.
To change the size of the Tooltips or to turn off Tooltips altogether, go to Tools, Customize, Toolbars. The Tools ➪ Customize menu option is inactive unless a SolidWorks document is open. To access Tools, Customize, first open a SolidWorks part, assembly, or drawing. Tools, Customize is different from the Customize Menu option that is found in all SolidWorks menus. The Customize Menu option is discussed later in this chapter.
NOTE
38
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 39
Navigating the SolidWorks Interface
Toolbar Icon Size You can set SolidWorks icons to be small or large by accessing the setting on the Tools ➪ Customize ➪ Toolbars ➪ Options menu. Figure 2.27 shows the difference between large and small icons.
FIGURE 2.27 A comparison of large and small icon size
Managing toolbars In SolidWorks 2007, it is easy to move, turn on and off, and add icons to toolbars. It is important to remember that different document types retain different toolbar settings; for example, the toolbars that you see with a part open are different from the toolbars that you see for drawings. When you are working on parts, it is important to have both the Sketch and the Features toolbars active. When you are working on a drawing, you will never use the Features toolbar, but you will frequently use the Sketch toolbar. Likewise for assemblies, you may want to display some additional toolbars and eliminate others. For this reason, when you change from a part document to a drawing document, you may see your display adjust because the changing toolbars increase or decrease the amount of space that is required. It is best practice to set up the toolbars for each document type so that they take up the same amount of space — for example, two rows on top and one column to the right. This way, changing between document types is not so jarring, with the graphics area resizing for each change.
BEST PRACTICE
Moving Toolbars To move a toolbar, you can click with the cursor at the double bar on the left end of the toolbar, as shown in Figure 2.28. The cursor changes to a four-way arrow, and you can then drag the toolbar where you want it. Toolbars dock either vertically or horizontally. You can resize undocked toolbars so that they have rows and columns. This arrangement is typically used with the Selection Filter toolbar, which is often left undocked and compressed into a block that is three or four columns wide.
FIGURE 2.28 Double bars enable you to move toolbars.
39
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 40
SolidWorks Basics
If the SolidWorks window is not wide enough for the toolbar to fit entirely in the screen, double arrows like those shown in Figure 2.29 display at the end of the truncated toolbar. When you click the double arrows, a flyout toolbar appears with the missing icons, as shown in Figure 2.30.
FIGURE 2.29 A truncated toolbar showing double arrows
FIGURE 2.30 You can display a flyout toolbar by clicking the double arrows.
Adding or Removing Toolbars and Icons You can add or remove toolbars in several ways: n Right-click any toolbar, and then activate or deactivate the toolbar. n Click Tools ➪ Customize, and then activate or deactivate the toolbar from the Toolbars tab. n Right-click any toolbar, select Customize, and again select the toolbar from the Toolbars tab. n Click View ➪ Toolbars to activate or deactivate toolbars.
NOTE
There are two toolbar entries in the View menu: the topmost toolbars allow you to turn toolbars on or off, and the bottom toolbars toggle the display of all of the toolbars.
To add or remove icons from toolbars, you must open the Tools ➪ Customize dialog box. You can access this dialog box in two ways. The first, most obvious method is to go through the menus to Tools ➪ Customize. The second, less obvious way is to right-click any toolbar (other than the CommandManager), select Customize, and then click the Commands tab. You can then select the toolbar that you want to add from the list. With the Customize dialog box open, you can remove a toolbar icon by dragging the icon away from the toolbar into white space in the graphics window. You can also reorder or move toolbar icons between toolbars. Figures 2.31 and 2.32 show the Toolbars and Commands tabs in the Customize dialog box.
40
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 41
Navigating the SolidWorks Interface
FIGURE 2.31 The Toolbars tab in the Customize dialog box allows you turn entire toolbars on and off.
Flyout Toolbars You can use any toolbar as a flyout toolbar. Figure 2.32 shows the list of all flyout toolbars, which is exactly the same as the list of all toolbars. Flyout toolbars are a nice space-saving feature for tools that you use infrequently, but frequently enough to want to avoid going through the menus. To use a toolbar as a flyout, select it from the Flyout Toolbars list and drag it onto an existing toolbar. It displays with an arrow to the right. Clicking the arrow causes all of the tools to scroll out temporarily until you click either a toolbar icon or anything else. To add icons to a flyout toolbar, temporarily show the regular toolbar that corresponds to the flyout toolbar, and add icons to the regular toolbar. When you are done adding or removing icons, turn off the regular toolbar; the changes are applied to the flyout. If you want to create a separate toolbar, you can commandeer an existing one for your own purposes. For example, because I do not use the Tools toolbar, I have removed all of the regular icons from it and replaced them with relevant flyout toolbars, which I do use extensively. This allows me to consolidate space, and not have unused icons on my toolbars.
TIP
41
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 42
SolidWorks Basics
FIGURE 2.32 The Commands tab in the Customize dialog box
Full Screen Mode Full Screen mode enables you to quickly toggle the display so that only the graphics window and the Task pane display; the FeatureManager, menus, toolbars, and status bar are all hidden. Alternatively, you can hide just the FeatureManager or the toolbars. In Full Screen mode, you can still access the menus by clicking the cursor along the top border of the window. n To toggle to Full Screen mode, press the F11 key. n To toggle the toolbar display, press the F10 key (see Figure 2.33). n To toggle the FeatureManager display, press the F9 key.
NEW FEATURE
42
Both Full Screen mode and the ability to hide the toolbars and the FeatureManager using hotkeys are new features in SolidWorks 2007.
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 43
Navigating the SolidWorks Interface
FIGURE 2.33 The SolidWorks window with all toolbars hidden using the F10 key
Workflow customization When you first install and run the SolidWorks software, you have the option to customize the interface using one of three pre-set option packages. Special menu and toolbar settings are made for Consumer Product Design, Machine Design, or Mold Design. The three workflow customizations affect the interface as follows: n Consumer Product Design adds the Surfaces toolbar to the CommandManager. n Machine Design adds Sheet Metal and Weldments toolbars to the CommandManager. n Mold Design adds Surfaces and Mold Tools toolbars to the CommandManager. Similar changes are made to the menus to hide or show menu selections as appropriate. You can find more information about hiding and showing menu items later in this chapter. If you want to select a different option after the initial setup, you can go to Tools ➪ Customize ➪ Options, where you can specify a different choice. Figure 2.34 shows the Options tab of the Customize dialog box.
43
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 44
SolidWorks Basics
FIGURE 2.34 The Options tab of the Customize dialog box, where you can select a different workflow customization
The CommandManager The SolidWorks CommandManager works like a toolbar, but has much more flexibility. The CommandManager is divided into two areas, the Control Area and the Toolbar Area. The Control Area allows you to select which toolbar icons you want to display in the Toolbar Area. The default CommandManager is shown in Figure 2.35, and the Features and Sketch toolbars are listed in the Control Area. You can put any toolbar in the Control Area to save a lot of interface space. At first, many users avoid using the CommandManager, but later come back to use it after seeing its flexibility and space-saving capabilities. I encourage you to give it a try. I was at first very skeptical of the benefits, until I used it for about a week, after which I was convinced.
44
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 45
Navigating the SolidWorks Interface
FIGURE 2.35 The SolidWorks CommandManager
Control area
Toolbar area
Minimizing the Size of the CommandManager Many users are concerned about the amount of space that is taken up by the CommandManager when it uses the default settings. After all, it is supposed to save space, but it is so huge! You can make the icons the same size as normal icons and remove the descriptions. To do this, right-click the CommandManager and deselect the Use Large Buttons with Text option.
Adding Toolbars to the CommandManager To add toolbars — such as Sheet Metal, Reference Geometry, or Tools — to the CommandManager, right-click the CommandManager, and select Customize CommandManager. This enables you to select additional toolbars. To reorder the toolbars in the Control Area, you must have Tools ➪ Customize activated.
Using the CommandManager You can use the CommandManager in two different ways. One way is to click the icon of the toolbar that you want to show in the Control Area, and then access the specific tools in the Toolbar Area. The other way is to use the Control Area icons as flyout toolbars, as shown in Figure 2.36.
FIGURE 2.36 Using CommandManager toolbar buttons as flyouts
45
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 46
SolidWorks Basics
Menus Everyone has his or her own style of working. For example, some people like to use menus and others do not. An example of a tool that does not have a toolbar equivalent is View ➪ Modify ➪ Section View, which is used to change the active section view’s settings. The most frequently used menu items are in the View, Insert, and Tools menus. All of the menus shown in this section have all of the possible selections turned on. As a result, the View menu in Figure 2.37 may contain options that are not available on your computer. Customizing menus is covered later in this chapter. The View menu is used primarily for turning on or off the visibility of entity types such as planes, sketches, or temporary axes. You can also do this by using hotkeys or by putting extra items on the View toolbar.
FIGURE 2.37 The View menu
46
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 47
Navigating the SolidWorks Interface
The Insert menu is used mostly for creating feature types for which you do not have a toolbar icon on the screen. For example, although the Move Face tool is only on the Mold Tools toolbar, it has many uses aside from mold design. You can find the Move Face tool on the Insert ➪ Face menu, as shown in Figure 2.38.
FIGURE 2.38 The Insert menu
The Tools menu is used primarily for sketch entities or tools for which you have no icon on the screen. Several other commonly used tools, such as Measure, Equations, and Options, are also available in this menu. Figure 2.39 shows the complete Tools menu.
47
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 48
SolidWorks Basics
FIGURE 2.39 The Tools menu
You can customize menus by adding or omitting items. By using the Customize Menu option at the bottom of any menu — including shortcut (right mouse button) menus — you can limit the items in any menu, by removing tools that you do not use. To bring back the removed items, you can either go back to the Customize Menu or go to Tools, Customize, Options and click the Reset to Defaults buttons for menu and shortcut customization. Be careful not to confuse this Customize menu selection with the Customize Menu selection on the Tools menu. Figure 2.40 shows the Tools menu being customized. Notice that several items at the top have been turned off.
48
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 49
Navigating the SolidWorks Interface
FIGURE 2.40 The Customize Menu option
The Tools ➪ Customize ➪ Options dialog box, shown in Figure 2.41, contains the Shortcut (right mouse button menu) and Menu customization options. These options enable you to show all of the menu items for both types of menus in a single stroke. By default, some items are hidden in various menus. Keyboard customization is discussed later in this chapter. SolidWorks terminology for Shortcut Menus and Shortcuts/Keyboard customization is slightly confusing because of these two overlapping, yet unrelated, terms. For this reason, we will refer to Shortcut Menus as RMB (right mouse button) menus from here on, because this is the standard terminology among SolidWorks users. Shortcuts are also generally referred to as hotkeys among users.
NOTE
49
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 50
SolidWorks Basics
FIGURE 2.41 The Tools ➪ Customize ➪ Options dialog box
Cursors SolidWorks cursors are context-sensitive, and change their appearance and function depending on the situation. Sketching cursors display a pencil and the type of sketch entity that you are presently sketching. Sketch cursors also display some dimensional information about the entity that you are sketching, such as its length or radius. Sketch cursor feedback is necessary for fast and accurate sketching.
CROSS-REF
To learn more about sketch cursor feedback, see Chapter 4.
The Select cursor changes, depending the item over which you move it. Cursor symbols also help to remind you when selection filters are active. The cursor is frequently available as an OK button. For example, after selecting edges for a Fillet feature, the RMB functions as an OK button.
50
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 51
Navigating the SolidWorks Interface
FeatureManager and PropertyManager windows The FeatureManager window is the panel to the left of the screen that shows an ordered record of features describing how the part was built. SolidWorks users spend a fair amount of time using the FeatureManager to edit or inspect models. Figure 2.42 shows the FeatureManager for a simple model.
FIGURE 2.42 The FeatureManager for a simple model
There is a splitter bar at the top of the FeatureManager that enables you to split the FeatureManager window into two windows, so that you can display the FeatureManager and another window, such as the PropertyManager. Small arrows in the middle of the right separator can collapse the FeatureManager to increase screen space. (The F9 key also collapses or opens the FeatureManager.) These elements are displayed in Figure 2.43. You can open the Display-pane flyout from the FeatureManager by using the double arrows at the top-right corner, as shown in Figure 2.43. The Display pane helps you to visualize where colors, textures, transparency, or hidden bodies have been applied. Unfortunately, nothing can be changed from the Display pane, which would be the most intuitive. However, it is helpful when looking for colors that are applied to the model at some level other than the part level. The Rollback bar at the bottom of the FeatureManager enables you to see the part in various states of history. All aspects of the FeatureManager are discussed in depth in Chapter 7.
51
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 52
SolidWorks Basics
FIGURE 2.43 Components of the FeatureManager Splitter bar Display pane arrows
Rollback bar
Collapse arrows
PropertyManager ConfigurationManager
The PropertyManager is where most of the feature dialog boxes go, and where you can edit properties of selected items such as sketch elements. You can manually switch to the PropertyManager using the tabs on the top of the Display panel. The left-most icon is the FeatureManager tab, the middle one is the PropertyManager tab, and the one on the right is the ConfigurationManager tab. Other icons may appear in this area for drawings, or if you have add-ins such as PhotoWorks or Animator turned on. One of the benefits of putting dialog boxes in the PropertyManager is that it saves a lot of space on the screen. On the other hand, you will often need to make a selection from the FeatureManager at the same time that the PropertyManager pops up and takes its place. This automatic pop-up behavior is controlled by a setting in the Tools ➪ Options ➪ System Options ➪ General ➪ Autoshow PropertyManager. When this window pops up, you may want to use either the splitter bars or the flyout FeatureManager. When creating or editing a feature, you can access the flyout FeatureManager by clicking the name of the feature at the top of the PropertyManager. The flyout FeatureManager is displayed just to the right of the regular FeatureManager, in the main graphics window, and is transparent to allow you to see the model through it. The flyout FeatureManager is shown in Figure 2.44, with a feature being edited in the PropertyManager.
52
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 53
Navigating the SolidWorks Interface
FIGURE 2.44 The PropertyManager for a sketch entity
Task pane By default, the Task pane sits to the right of the SolidWorks screen, although you can dock it on the left side or leave it undocked entirely. When the Task pane is expanded, you can collapse it by clicking outside of it. If you want to keep it open, click the pushpin in the upper-right corner of the pane. The Task pane is shown in Figure 2.45.
FIGURE 2.45 The Task pane
53
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 54
SolidWorks Basics
The Task pane is the home for several panels: n SolidWorks Resources: These are useful links for templates, tutorials, tech support, news, GlobalSpec search, Tip-of-the-Day, and other resources. n Design Library: This includes locally stored libraries, Toolbox, and 3D Content Central. n File Explorer: This is a Windows Explorer–like interface that you can use to browse for files. n SolidWorks Search: If you have installed the Windows Desktop Search with SolidWorks 2007 and indexed your files, you can perform searches that include filename and custom properties. n View Palette: This palette allows you to visually select views and drag them onto a drawing sheet.
Status bar The status bar is a non-intrusive way in which SolidWorks communicates information back to the user. It is located at the bottom of the screen, and you can enable it from the View menu. Figure 2.46 shows the status bar in action.
FIGURE 2.46 The status bar showing a Tooltip for the Sketch Circle tool
The status bar can display the following information, indicators, and icons: n Progress as parts, assemblies, or drawings load n Tooltips for icons n Measurements n Sketch status for an active sketch n In-context editing n Suspend Automatic Rebuilds n Icons that allow you to turn Quick Tips off or on n Sheet scale for drawings n Cursor position for drawings and sketches n Whether you are editing the sheet, sheet format, or view of a drawing
54
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 55
Navigating the SolidWorks Interface
2D Command Line Emulator This is a tool specifically for people who are coming to SolidWorks from AutoCAD. As the name suggests, it adds a command line to the bottom of the SolidWorks window, that works like the AutoCAD command line in most respects. The available commands are somewhat limited compared to those that are available in AutoCAD. This tool only functions in the 2D sketch mode, on a drawing sheet, or in a drawing view; it does not work in a 3D sketch. The 2D Command Line Emulator is shown in Figure 2.47.
FIGURE 2.47 The 2D Command Line Emulator in action
Available sketch tools in the 2D Command Line Emulator include: Align, Arc, Array, ‘Cal, Chamfer, Chprop, Circle, ‘Color, Copy, DDcolor, Dim, Dist, Ellipse, Erase, Exit, Extrude, Fillet, ‘Grid, Line, List, Massprop, Mirror, Move, Offset, ‘Ortho, ‘Osnap, ‘Pan, Plot, Point, Polygon, Qsave, Rectangle, ‘Redraw, ‘Redrawall, Revolve, Rotate, Save, Saveas, ‘Snap, Spline, Trim, U (undo), ‘Units, ‘View, and ‘Zoom. Commands that are preceded by an apostrophe (‘) can be used as transparent commands, without exiting an active command. Notice that even the cursor changes to crosshairs. The best way to learn a new software package is to embrace the new way, not to cling to the old way. Although you may find the 2D Command Line Emulator more comfortable to work with, you will not achieve the same results as you will with the SolidWorks default sketching mode. For example, the resulting sketch entities created using the 2D Command Line Emulator are not constrained in any way, and the endpoints do not even merge. You can turn off the 2D Command Line Emulator by going to Tools, Add-ins.
BEST PRACTICE
55
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 56
SolidWorks Basics
Making the Interface Work for You As engineers and designers, we all like to tinker with things to optimize efficiency and to apply our personal stamp. When it is installed, the SolidWorks interface is functional, but not optimal. In the previous pages, we have discussed managing and customizing toolbars and menus. In the remainder of this chapter, we discuss more about customizing the interface, and suggest some strategies that you might use to help customize your work environment.
Customizing colors You need to be aware of a few things before you change all of the standard colors in the SolidWorks interface to whatever strikes your fancy. The first is that SolidWorks does not automatically alter text color to contrast with your background. As a result, if you set the background to black, and the text is black, you won’t be able to see the text. This may seem obvious to some people, but AutoCAD automatically changes text color to contrast with the viewport background, and so AutoCAD users may take this functionality for granted. Some colors should be avoided for the background, or you should at least make some other changes if you choose these colors. Black is used with fully defined sketches, dimensions, FeatureManager text, and annotations. Blue backgrounds often mask the underdefined sketch color. Bright green backgrounds can cause problems with seeing selected items. Bright red, aside from being a terrible color to stare at all day, also does not contrast well with some of the red highlights and error colors. You might say that whatever color background you select, it makes items or features difficult to see. For this reason, many users choose a gradient background, which allows you to pick colors where items are always visible on one half of the screen or the other. Staring at a white screen all day can be uncomfortable for your eyes, so pick colors that allow you to see everything with “reasonable” contrast, yet that are not glaringly bright. Very high contrast is hard on the eyes, and low contrast may make it difficult to distinguish items on the screen. In addition to colors and gradients, you can use an image as the graphics window background. This gives you a wider range of customization capabilities, and several sample images are already available in the default settings.
Customization strategies You can easily customize many aspects of the SolidWorks interface, including: n Toolbars n Menus n Background colors or images n PropertyManager skins
56
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 57
Navigating the SolidWorks Interface
n Task pane location n Hotkeys n Macros n Custom application programming Whether or not you should customize each of the above items depends partially on how much time and energy you have to spend, as well as how much money you are ready to dedicate in the case of custom programming.
Hotkey approaches Some of us old-timers prefer to use the keyboard over the mouse. If your hand-eye coordination is as bad as mine, you may also choose this approach. I can type without looking at the keyboard, but when I use the mouse, it takes me a few seconds to aim at an icon and hit it accurately. This means that I customize SolidWorks to use as many hotkeys as possible, and remove icons from the interface if I have them on a shortcut. Unfortunately, my memory is as bad as my eyesight, and so remembering 75 hotkey commands is a bit of a problem. I admit to having a printed list of hotkeys taped to the side of my monitor. While I know that needing to read the list to find a particular hotkey defeats most of the purpose of using them in the first place, I just accept it as a learning aid. I generally do not advocate trying to standardize a hotkey scheme across multiple users, unless the users all agree to it. The underlying reason for writing a section entitled Hotkey Approaches is that everyone remembers things differently in the first place, and people have different tolerance levels for various irritations. Any command that I use more than a few times an hour is worth assigning to a hotkey. I like to use alliteration when assigning keys to help with my faulty memory. Most-frequently used commands are assigned single-letter hotkeys, and less-frequently used commands are assigned combinations. Thus, Tools Options is linked to O, Measure to M, Select Vertex to Shift+V, and Curve Projected to Ctrl+J (Ctrl+P is the Windows standard for the Print command). Other people like to group keys into easy-to-reach combinations, and so the Q, W, A, S, Z, and X keys are often assigned first for right-handed mouse users.
Organizing Hotkeys Hotkeys are assigned and organized in the Tools ➪ Customize ➪ Keyboard dialog box, as shown in Figure 2.48. This interface enables you to see all of the hotkeys (called shortcuts in the list) easily. If you try to enter an existing hotkey, SolidWorks issues a prompt, telling you that the key is assigned to another command and what the command is, and asking you if you want to clear the other instance of the hotkey and make the new one active. You can also print out or copy to the Clipboard a list of only commands that use hotkeys.
57
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 58
SolidWorks Basics
Because the list of commands is so long, there is a Search function available, and a drop-down arrow that makes visible only the commands from a selected menu. The list of commands is organized by menu name, and the menus are listed as they occur in the interface. Fortunately, here on the Keyboard tab, SolidWorks allows you to sort using the column headers to list the menus, commands, or hotkeys in alphabetical order, simply by clicking the column header. This is a highly usable interface.
NEW FEATURE
This method for organizing and assigning hotkeys is new for SolidWorks 2007.
FIGURE 2.48 Tools ➪ Customize ➪ Keyboard — the hotkey interface
Using the keyboard Moving between the mouse and the keyboard can be bothersome and time consuming. In addition to the hotkey approach, you can use another keyboard method to save time. Many users become adept at using the Alt-key combinations to invoke menu items. Most menu items in Windows applications contain a single underlined letter. To access a top-level menu, you can hold down the Alt key and press the underlined letter for that menu, and then just press an underlined letter in the menu to access specific commands. This technique enables you to navigate most of the interface without using the mouse. For example, to exit SolidWorks, instead of using the mouse to click the red X in the upper-right corner, you could press Alt+F, X. In Figure 2.49, you can see that the F in File is underlined, as is the X in Exit.
58
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 59
Navigating the SolidWorks Interface
FIGURE 2.49 Accelerator Keys in the File menu
The SolidWorks documentation terminology becomes further confused when talking about accelerator keys. It says that the general class of keys is called Shortcuts, which can be either accelerator keys or keyboard shortcuts. How these are distinguished from Shortcut Menus is not clear. Again, for our purposes in this book, we refer to the shortcut menus as RMB (right mouse button) menus, accelerator keys as Alt-keys, and keyboard shortcuts as hotkeys, which is more in line with standard usage than the documented terminology.
NOTE
Fewest number of icons In order to maximize valuable space on the monitor, many SolidWorks users strive to minimize the number of toolbar icons on the screen, or confine it to two rows of toolbars. You can do this by using the CommandManager, flyout toolbars, and hotkeys, and removing unused icons, as well as the other techniques discussed here.
Device approaches If you have never used a Spaceball or equivalent view-manipulation device, you should consider it. They are wonderful devices and do far more than just spin the view. Most of the devices also have several programmable buttons that you can link to menu items. They can move drawing views, and parts within assemblies, and even manipulate selected objects in other Office applications and Web browsers. In addition, some game controllers, such as the Microsoft Sidewinder, are inexpensive and offer almost endless possibilities with button programming. I have not yet come across a tablet that works well for SolidWorks command input. I believe that tablets have the same shortcomings as mice because they both require that you look at what your hands are doing.
59
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 60
SolidWorks Basics
Macros Macros are short snippets of programming code that have a particular function. Most macros are small and intended for simple tasks that are repeated many times, such as drawing a rectangle centered on the origin of a selected plane, or changing selected dimensions to four decimal places. Macros may be recorded, written from scratch, or a combination where you record a particular action to be used as a starting point, and then embellish it manually from there. Recorded macros may not always record the parts of the action that you want to make into a macro, but you can edit them manually to include anything that you can program with VBA (Visual Basic for Applications), which is included with the base SolidWorks package at no extra cost.
CROSS-REF
Macros are covered in more detail in Chapter32. Appendix C also contains sources for macros and macro-related help.
To access macros by using hotkeys, follow these steps: 1. Make a folder in your SolidWorks installation directory called “macros”. 2. Copy macros into this folder. 3. Start (or restart) SolidWorks. 4. Go to Tools ➪ Customize ➪ Keyboard. 5. Scroll to the bottom of the list under the Macros category, and assign hotkeys as you would for standard SolidWorks commands.
Whether you are skilled at writing or recording macros, or you are just using macros collected from other people, they can be huge time savers and offer functionality that you would not otherwise be able to access.
Saving custom interface settings Once you have set up your menus and toolbars, worked out all of the custom colors, figured out your hotkey usage, and connected your macros, you don’t want to lose these settings when you reinstall the software or move to a different computer. Another user may want to share your settings, or you may want to transfer them to your home computer (for modeling the new deck or the doghouse, of course). Fortunately, these settings are very portable. You can use the Copy Settings Wizard to save these settings out to a file. Access the wizard through Start, Programs, SolidWorks 2007, SolidWorks Tools, Copy Settings Wizard. This creates a file with an *.sldreg file extension. You can restore settings by double-clicking this file on a computer that has SolidWorks installed on it. The SolidWorks settings are actually Windows registry settings. The file that is saved by the wizard is just a registry file that has a different extension to prevent it from being applied too easily. Savedout registry files have a *.reg file extension, and are integrated into the registry by simply doubleclicking them. If you are not familiar with the Windows registry, you should not make direct
60
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 61
Navigating the SolidWorks Interface
changes, because even small changes can cause serious problems with your operating system or even hardware. The settings that are saved out by the Copy Settings Wizard are safe to transfer between computers. In order for the Copy Settings Wizard to work, you need to have Administrator-level access to your computer. The Copy Settings Wizard is shown in Figure 2.50.
FIGURE 2.50 The Copy Settings Wizard
Working with multiple-document windows In SolidWorks, as in other areas of life, things can become chaotic. You may sometimes have the luxury of working on a single part at a time, but more often, you will find yourself with several models open at once. This is a common situation for most users. Fortunately, SolidWorks has several methods for dealing with “information overload,” to help you sort through it all.
Window management Like most other Windows applications, SolidWorks can arrange the open document windows in one of several ways that are available through the Window menu, as shown in Figure 2.51: n Cascade: Most useful for accessing documents that are to be edited one by one. n Tile Horizontally: Most useful for wide and short parts. n Tile Vertically: Most useful for tall, narrow parts, or documents where you want to compare items in the FeatureManager. n Arrange Icons: When windows are minimized to icons, this menu selection arranges the icons neatly, starting in the lower-left corner of the window.
61
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 62
SolidWorks Basics
FIGURE 2.51 The Window menu
The images in Figure 2.52 show the window-management settings listed above.
FIGURE 2.52 Window Arrangements: Cascade, Tile Horizontally, and Tile Vertically
62
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 63
Navigating the SolidWorks Interface
Also remember that you can use the F9 key to close the FeatureManager, and the F10 key to remove the toolbars to create extra interface space when arranging several windows in the graphics window.
Changing windows You can use several techniques to change from one window to another. By clicking on the Window menu, you can view a list of open document windows, as shown in Figure 2.51. You can then select the desired window directly from this menu. If more than a few windows are open, a More Windows option appears at the end of the list, as shown in Figure 2.53. Clicking on this option brings up a separate window that enables you to select from the complete list.
FIGURE 2.53 You can select from a list of several windows.
When a smaller number of windows are open, a simpler way to change windows is to press Ctrl+Tab. This is a Windows standard technique that also works in other Office applications. Ctrl+Tab takes you in one direction in the list of open windows, and Ctrl+Shift+Tab takes you in the opposite direction through the list.
Tutorial: Getting to Know the Interface By this point, you really have not learned much about making parts, assemblies, and drawings in SolidWorks, but you have learned quite a bit about using the interface. In this tutorial, you get some hands-on practice at making the changes that we have discussed in the rest of this chapter. The rest of the book also uses the settings that you create here.
63
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 64
SolidWorks Basics
Tutorial goals This tutorial is intended to reinforce the following skills: n Adding and removing toolbars n Adding and removing toolbar buttons n Adding and removing items from drop-down and RMB menus n Setting up the CommandManager n Setting up hotkeys n Linking a hotkey to a macro n Changing interface colors
Copy the existing settings Regardless of what your initial settings are, you do not want to lose them. Before you start to make changes to your system, you should save out the existing settings to a file from which they can be recovered. You can do this using the Copy Settings Wizard, as shown in Figure 2.54.
FIGURE 2.54 The Copy Settings Wizard
To use the Copy Settings Wizard, follow these steps: 1. Close SolidWorks. 2. Click Start ➪ Programs ➪ SolidWorks 2007 ➪ SolidWorks 2007 Tools ➪ Copy Settings Wizard. 3. Select Save Settings, and click Next.
64
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 65
Navigating the SolidWorks Interface
4. Enter a location and a name for the file. 5. Select the items that you would like to save. For the purposes of this tutorial, make sure that the following options are selected: Keyboard Shortcuts, Menu Customization, Toolbar Layout, and All Toolbars. 6. Click Finish.
Browse to the location where you saved the file and make sure that it is there.
Set all interface items to their default settings You can set the interface back to the default settings using one of two methods. The first method, editing the Windows registry, may not be available to all users. It requires Administrator access to your computer and a good familiarity with Windows.
CAUTION
Editing the Windows registry can be dangerous if you make a mistake. Do not attempt this method is you have any doubts about what you are doing.
To set SolidWorks back to its default settings, follow these steps: 1. Close SolidWorks. 2. Click Start ➪ Run. 3. Type regedit, and click OK. 4. Browse to HKEY_CURRENT_USER\Software\SolidWorks\SolidWorks 2007 or the appropriate folder for the version that you are using. 5. To return all settings in SolidWorks back to default, delete the entire SolidWorks 2007 folder. 6. Close the Registry Editor. 7. The folder is recreated when SolidWorks starts up again, and is populated with default values.
The second method, which is less risky but less complete, is to go to the main locations and use the tools provided to return settings to their defaults. Restart SolidWorks and create a new blank document (you cannot display the Customize dialog box without a document open). To access the resets for the interface, do the following: n Click Tools ➪ Options ➪ General ➪ Reset, and go to the bottom-left area of the dialog box. n Click Tools ➪ Customize ➪ Toolbars ➪ Reset, and go to the bottom-left area of the dialog box. n Click Tools ➪ Customize ➪ Menus ➪ Reset All, and go to the right side of the dialog box. n Click Tools ➪ Customize ➪ Keyboard ➪ Reset to Defaults, and go to the upper-right area of the dialog box. n Click Tools ➪ Customize ➪ Options; there are three Reset to Defaults buttons along the left side of the dialog box.
65
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 66
SolidWorks Basics
Customizing the CommandManager Now that you have restored the default settings, you can begin customizing the interface with the CommandManager. To do this, RMB click anywhere on the CommandManager and deselect the Use Large Buttons with Text option, as shown in Figure 2.55. When you have done this, the check mark should no longer appear in front of the option.
FIGURE 2.55 Deselect the Use Large Buttons with Text option.
Next, add some toolbars to the Control Area of the CommandManager, as follows: 1. Again, RMB click the CommandManager, and select Customize CommandManager. 2. Select the Surfaces, Sheet Metal, and Annotations toolbars from this list, which is partially shown in Figure 2.56. Deselect the Sketch toolbar.
FIGURE 2.56 The Customize CommandManager
3. Click outside of the list; the list closes and applies the changes you made. 4. Click the Features toolbar button in the Control Area of the CommandManager, and make sure that the Features toolbar buttons appear in the Toolbar Area to the right.
66
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 67
Navigating the SolidWorks Interface
5. RMB click any toolbar other than the CommandManager, and select Customize; this brings up the Tools ➪ Customize dialog box, where you can add, remove, and reorder toolbar buttons. 6. Reorder the toolbars in the Control Area of the CommandManager so that the Annotations toolbar comes first. When you are done, The CommandManager should look like Figure 2.57. Leave the Customize dialog box open.
FIGURE 2.57 The CommandManager with your changes applied
7. Make sure that the Toolbars tab of the Customize dialog box is displayed. 8. Turn on the Sketch and Tools toolbars. 9. Place the Sketch toolbar to the right of the Task pane, and the Tools toolbar just above the Task pane. 10. Drag the Reference Geometry and Curves flyout toolbars from the end of the Features toolbar in the CommandManager over to the Tools toolbar, as shown in Figure 2.58. Use the Tooltips to identify the buttons.
FIGURE 2.58 Move these toolbar buttons from the Sketch toolbar to the Tools toolbar.
Move these two...
Tools toolbar ...over here.
CommandManager
The display should now look like Figure 2.59. Close the Customize dialog box.
67
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 68
SolidWorks Basics
FIGURE 2.59 The customized SolidWorks interface
Customizing menus If you always do the same types of work, or more importantly, never do certain types of work, then you might consider customizing some menus to remove items that you never use. Customization applies to both the main drop-down menus and the context-sensitive RMB menus. To customize a menu: 1. Click Insert ➪ Customize Menu. 2. Turn off the menu items Sketch from Drawing, DXF/DWG, Object, Hyperlink, and Picture, as shown in Figure 2.60. Click anywhere outside of the list to close it. 3. Click the Insert menu to ensure that the deselected items have been removed. 4. RMB click the Right plane in the FeatureManager. 5. Select Customize Menu. 6. Turn off Section View. Click anywhere outside of the list to close it. 7. RMB click the Right plane to verify that Section View has been removed.
68
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 69
Navigating the SolidWorks Interface
FIGURE 2.60 Customizing the Insert menu
Change interface colors Edit the colors used in the interface: 1. Click the Select Color Scheme tool from the Standard toolbar. Each time you click this tool, the background color changes to a new scheme. 2. Click the drop-down arrow to the right of the button to see the entire list. Select another scheme from the list. 3. Click Tools ➪ Options ➪ Colors to display the dialog box shown in Figure 2.61. 4. Change the viewport background color to white (preview thumbnails use this background color). 5. Adjust the top gradient and bottom gradient colors to your personal taste, but choose colors that are both functional and attractive. 6. Set the Background Appearance toggle to Gradient. 7. Make sure that the Match Graphics Area and FeatureManager Backgrounds option is selected.
69
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 70
SolidWorks Basics
FIGURE 2.61 The Tools ➪ Options ➪ Colors dialog box
8. Deselect the Use Specified Color for Shaded With Edges Mode option. This makes the edges of models a similar hue to the part itself, rather than the cartoonish-looking black edges. 9. Click the Save As Scheme button, and save the scheme with your name or another filename that is easily identifiable. 10. Click OK to close the Tools ➪ Options ➪ Colors dialog box. 11. Again, click the drop-down list next to the Select Color Scheme tool; your new custom color scheme should now have been added to the list.
Adding hotkeys For many users, hotkeys are an integral part of the everyday experience of using SolidWorks. You can easily assign hotkeys and manage the assignments by following these steps: 1. Click Tools ➪ Customize ➪ Keyboard. 2. In the Search For text box, type Options. 3. Click in the Shortcut column, and type O. 4. Click again in the Search For text box, and type Customize. 5. Click in the text box next to the Tools ➪ Customize entry and press Ctrl+C. Answer no to the question of whether you want to reassign the hotkey. Press Ctrl+T instead.
70
07_080139 ch02.qxp
3/26/07
3:28 PM
Page 71
Navigating the SolidWorks Interface
6. Click OK to exit the Customize dialog box. 7. Press the O key to bring up Tools ➪ Options. Click OK to exit. 8. Press Ctrl+T to bring up Tools ➪ Customize. Click OK to exit. 9. Press Alt+F, and then press X to exit SolidWorks.
Combining macros with hotkeys Macros are covered in Chapters 34 and 35, but the following steps show you how to link a macro to a hotkey:
ON the CD-ROM
You can use the macro called rectangle.swp, located on the CD-ROM.
1. Find your SolidWorks installation directory. By default, this directory is C:\Program Files\SolidWorks. 2. Create a folder called Macros in the SolidWorks directory and put the rectangle.swp macro in it. 3. Start SolidWorks. 4. Create a new blank part document. 5. Press Ctrl+T to access the Customize dialog box. 6. Click the Keyboard tab. 7. In the Search For text box, type rectangle. 8. Click in the Shortcut column next to the listing with the Category of Macros, and press R. 9. Click OK to exit the Customize dialog box. 10. Press R. The rectangle macro runs and draws a sketch rectangle on the Front plane, centered on the origin. 11. Press Ctrl+S to access the Windows standard hotkey for the Save command. Name the part rectangle.sldprt and save it to a workspace directory. 12. Press Alt+F and then X to exit SolidWorks.
The use of Alt-keys and hotkeys is somewhat exaggerated in this tutorial, but it is intended to get you used to working with them.
Summary The SolidWorks interface is quite busy, and you can access most items in multiple ways. This allows you to choose how you work, whether through toolbars, the CommandManager, or menus, among other choices. The fact that SolidWorks is so tightly integrated into Windows means that in most cases, you know what to expect from the interface, and much of your knowledge from using other applications is transferable.
71
2
07_080139 ch02.qxp
Part I
3/26/07
3:28 PM
Page 72
SolidWorks Basics
The SolidWorks interface is also customizable through all of the standard Windows methods, such as rearranging toolbars, customizing menus and hotkeys, and changing background colors and skins. If you spend a significant amount of your workweek using this software, you want to take some time to configure it for efficiency and comfort. Because of the complexity of the interface and the myriad ways in which you can use it, each user is expected to create an interface that looks a little bit different from anyone else’s.
72
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 73
Getting Started with SolidWorks
S
olidWorks uses several file types to accomplish tasks. The most frequently used types are parts, assemblies, and drawings. Beyond these, we have templates for each type and drawing format. The difference between drawing templates and drawing formats is cause for frequent confusion among many SolidWorks users, and so we will spend some extra time on this topic. Other file types also exist, such as design tables, Bill of Materials, or BOM, templates, and table templates, sheet-metal gauge tables and bend tables, custom symbol and line type files, custom property files, color swatches, library features, and macros. This chapter contains a complete list of these file types. Some of them allow you to customize SolidWorks using simple but little-known techniques, such as the ability to add custom symbols that can be inserted into a string of text, or to create new line types, or to change how SolidWorks creates hole callouts. If you are a CAD Administrator looking for advice on how to implement SolidWorks, this chapter includes some information, but you should also refer to Appendix A, “Implementing SolidWorks,” for additional information and higher-level planning suggestions.
Tools for Beginners SolidWorks has many tools for beginning users that are available when you install the software. A default installation presents you with several options when you launch the software for the first time. Following is a catalog of these options and how to benefit most from them. If you plan to attend formal SolidWorks reseller-based training, it is a very good idea to first go through some of the tutorials in this section, so that you
73
IN THIS CHAPTER Tools for beginners Identifying SolidWorks documents Opening existing documents Using visualization tools Tutorial: Creating a part template Tutorial: Visualization techniques
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 74
SolidWorks Basics
are prepared to ask educated questions and have an advantage over the rest of the class. You will also get more out of the training if you have seen the material once before.
SolidWorks license agreement Although the license agreement does not have any bearing on learning how to use the software — other than the fact that it allows for a Home Use License — it is useful to be familiar with what it says. Many users find this part of the license agreement, shown in Figure 3.1, to be helpful. The primary user of the license at work is also allowed to use the license at home or on a portable computer. This is often a good option for learning, additional practice, or completing the design of a personal project such as a deck or soapbox derby car. Once you finish reading the License Agreement page, you can select Accept to continue.
FIGURE 3.1 The SolidWorks license agreement
Welcome to SolidWorks The Welcome to SolidWorks screen, shown in Figure 3.2, follows the License Agreement page. It helps you to establish what type of tools you would like to see in the interface, and offers some help options.
FIGURE 3.2 Welcome to SolidWorks screen
74
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 75
Getting Started with SolidWorks
Quick Tips The Quick Tips feature enables balloons with tips to help you get started with several tasks. For example, the first Quick Tip that you see may be the one shown in Figure 3.3. When you begin to create your first document in SolidWorks, a Quick Tip guides you through this process.
FIGURE 3.3 A New SolidWorks Document Quick Tip
As you begin working, Quick Tips displays a dialog box at the lower-right corner of the graphics window that offers context-sensitive help messages, as shown in Figure 3.4. As you work with the software, these messages will change to reflect what you are doing.
FIGURE 3.4 The main Quick Tip window
You can turn Quick Tips on or off using the small icon on the taskbar in the lower-right corner, as shown in Figure 3.5. You can also turn Quick Tips on or off using the Help menu, by selecting Quick Tips. The on/off setting is document-type sensitive, and so if you turned this feature off in part mode, then you must also turn it off for assemblies and drawings. Quick Tips are a great way to get started if you are a beginner, as well as to refresh your memory if it has been a while since you worked with the program, or if several versions have gone by since you last used the software.
75
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 76
SolidWorks Basics
FIGURE 3.5 Turning Quick Tips on or off
The first time that you create a document, you are prompted to select units for your default templates, as shown in Figure 3.6. This is an important step, although you can change this setting later if necessary. You can find more information on part and assembly templates later in this chapter, and drawing templates are described in detail in Chapter 20.
FIGURE 3.6 Selecting the default template units
The main significance of this default template unit option is not so much the units as the dimensioning standard that you are selecting. ISO and ANSI standards use different methods of projecting views. ISO is typically a European standard and uses First Angle Projection, while ANSI is an American standard and uses Third Angle Projection. Third Angle Projection is used throughout this book. The difference between First and Third Angle Projections can cause parts to be manufactured incorrectly if those reading the prints do not notice the difference or see that there is some discrepancy. Figure 3.7 demonstrates the difference between these two methods. Make sure that you specify the correct option. If someone else, such a computer specialist who is not familiar with mechanical drafting standards, has initially set up SolidWorks on your computer, then you should verify that the default templates are correct.
76
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 77
Getting Started with SolidWorks
FIGURE 3.7 Differences between First Angle Projection (left) and Third Angle Projection (right)
You can find another setting that affects projections by selecting Tools ➪ Options ➪ Display/ Selection ➪ Projection Type For Four View Viewport. This does not follow the dimensioning standard that is selected for the default templates, or the country in which the software is installed.
CAUTION
The default setting for this option is First Angle Projection.
Online documentation Several types of online documentation are available to help SolidWorks learners along their path. A great place to start is the SolidWorks Resources tab of the Task pane, on the right side of the screen. This is the first tab in the list, and displays the Home icon. The Getting Started section of the SolidWorks Resources tab is shown in Figure 3.8.
FIGURE 3.8 The Getting Started section of the SolidWorks Resources tab on the Task Manager
77
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 78
SolidWorks Basics
Making My First Part and Making My First Drawing The Getting Started area contains two beginner-level tutorials that are aimed at helping you understand the basics of part and drawing creation, and also to get used to the interface. These tutorials are about 30 minutes long.
Online Tutorials The Online Tutorials link takes you to a list of 35 basic tutorials on subjects from sheet metal to macros, in parts assemblies and drawings. These tutorials are certainly worth your time, and can build your skills and knowledge of basic functionality. This SolidWorks Bible distinguishes itself by going into far more detail and depth about each function, adding information such as best practice, performance considerations, and cautionary data, and acting as a thorough desk reference.
Moving from AutoCAD The Help menu contains a selection called Moving from AutoCAD. This is intended to assist the transitioning user to acclimate to their new surroundings. Terminology is a big part of the challenge when making this switch, and prominently figures in the Moving from AutoCAD help file. The most helpful tools in Moving from AutoCAD are probably the Approach to Modeling and Imported AutoCAD Data sections. They contain information that is useful whether you are coming to SolidWorks from AutoCAD or another CAD package.
Online User’s Guide The Online User’s Guide is the traditional Help file. You can use either the Index or Search capabilities to find what you are looking for. The Online User’s Guide contains screen captures and animations, sample files, and even a separate API (Application Programming Interface) help file.
What’s New With every release, SolidWorks publishes a What’s New document to help you keep up to speed with the changes. This is typically a PDF file with accompanying example files. If you have missed a version or two, then you can read through the What’s New files to get back on track.
Tip of the Day The SolidWorks Tip of the Day displays at the bottom of the SolidWorks Resources tab on the Task pane. You can cycle through a few of these tips or use them to quiz coworkers to build useful skills.
Hardcopy documentation Over time, software companies have reduced their hardcopy documentation. They often claim that keeping up with the changes in print is too much work and too inefficient, but most users prefer to have a physical book in their hands, to spread out on the desk next to them, to earmark, highlight, and mark with post-its. Hardcopy documentation still has an important role to play in the dissemination of information.
78
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 79
Getting Started with SolidWorks
SolidWorks does publish some pamphlet-sized hardcopy documentation that ships in the box with new installation and upgrade CDs.
Quick Start The Quick Start pamphlet acts as a rough outline for issues that range from installation to getting help.
Quick Reference Guide The Quick Reference Guide is a foldout card that contains some of the symbols that display in the FeatureManager as well as other locations. This card also contains some of the default hotkeys and customization options.
Identifying SolidWorks Documents Although SolidWorks uses three main types of data files, there are many more types of supporting files that you should know about if you are concerned with customization and creating implementation standards.
Document types SolidWorks main design document file types: Design Documents n *.sldprt: SolidWorks Part file type n *.sldasm: SolidWorks Assembly file type n *.slddrw: SolidWorks Drawing file type SolidWorks template document file types: Templates and Formats n *.prtdot: Part Template n *.asmdot: Assembly Template n *.drwdot: Drawing Template n *.slddrt: Drawing Sheet Format n *.sldtbt: General Table Template n *.sldbombt: BOM Template (table-based) n *.xls: BOM Template (Excel-based) n *.sldholtbt: Hole Table Template n *.sldrevtbt: Revision Table Template
79
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 80
SolidWorks Basics
n *.sldwldtbt: Weldment Cutlist Template n journal.doc: Design Journal Template SolidWorks library document file types: Library Files n *.sldlfp: Library Part File n *.sldblk: Blocks
NOTE
Forming Tools used to be created as *.sldlfp files, but are now simply *.sldprt.
Favorites n *.sldweldfvt: Weld Favorite n *.sldgtolfvt: Geometric Tolerance Favorite n *.sldsffvt: Surface Finish Favorite n *.sldnotefvt: Note Favorite n *.sldsffvt: Surface Finish Symbol Favorite Symbol Files n gtol.sym: Symbol file that allows you to create custom symbols n swlines.lin: Line Style definition file that allows you to create new line styles Others n *.sldreg: SolidWorks settings file n *.sldmat: Material Database n *.sldclr: Color Palette file n *.txt: Custom Property file, Sheet Metal Bend Line Note File n *.swp, *.swb: Macros, Macro Features n *.btl: Sheet Metal Bend Table n *.xls: Sheet Metal Gauge Table n calloutformat.txt: Hole Callout Format file
Saving your setup If you have taken time to set up a computer and then need to reinstall SolidWorks, move to another computer, or duplicate the setup for another user, then you need to copy out these files. Keep in mind that you need to copy only the files that you have used or customized. By default, all of these files are located in different folders within the SolidWorks installation directory. The previous chapter
80
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 81
Getting Started with SolidWorks
dealt with interface settings and creating a registry settings file to copy to other computers or use as a backup. However, you also need to copy the various file types that comprise a custom installation. When you create complex implementations that include templates for various types of tables or customized symbol files, it is important to have these files in a location other than the default installation folder. Otherwise, uninstalling SolidWorks or installing a new version will delete all of your hard work. You can use the Tools, Options, File Locations to locate these files in separate library folders, which may be on the local hard drive or on a network location.
BEST PRACTICE
Templates When you create a new file, the New dialog box allows you to select one of several files to start from; these files are templates. Think of templates as “start parts” that contain all of the document-specific settings for a part (Tools ➪ Options ➪ Document Properties). The same concept applies to assemblies and drawings. Templates generally do not contain any geometry, although this is possible. The Novice interface for the File ➪ New SolidWorks Document dialog box only allows you to select default templates. The Advanced interface allows you to select any available templates.
TIP
As shown in Figure 3.9, several tabs can display on the Advanced interface. Each of these tabs is created when you create a folder in the template directory by selecting Tools ➪ Options.
Using Multiple Document Templates Using multiple templates enables you to start working from multiple starting points. This offers you an advantage in many situations, such as: n Standardization for a large number of users n Working in various units n Pre-set materials or colors n Pre-set custom properties n Parts with special requirements, such as sheet metal or weldments n Drawings of various sizes with formats (borders) already applied n Drawings with special notes already on the sheet Drawing templates and formats are complex enough that they are dealt with in their own separate chapter. Chapter 20 discusses in-depth the differences between templates and formats, as well as how to use them to your best advantage. This chapter only discusses part and assembly templates.
CROSS-REF
Depending on what you need, you may want to have metric and inch part and assembly templates, part templates for steel and aluminum, separate templates for sheet metal parts, and another one for weldments, if you design these types of parts. If your firm has customers with different requirements, you may consider using separate templates for these customers. Over time, you will discover the types of templates that you need, because you will find yourself making the same changes over and over again.
81
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 82
SolidWorks Basics
FIGURE 3.9 The Novice and Advanced interfaces for the New SolidWorks Document dialog box
To create a template, open the appropriate document type (part or assembly), and make the settings that you want the template to have. For example, units are one of the most common reasons to make a separate template. In fact, any of the Document Property settings is a good reason for creating a template, from the dimensioning standard that is used to image quality settings.
CROSS-REF
Document Property settings are covered extensively in Appendix B.
Some document-specific settings are not contained in the Document Properties dialog box. However, these settings are saved with the template. Settings that fall into this category are the View menu entity-type visibility options and the Tools ➪ Sketch Settings options. Custom Properties are another piece of the template puzzle. If you use or plan to use BOMs, PDM, or linked notes on drawings, then you need to take advantage of the automation options that are available by using custom properties. Setting up custom properties is covered in detail in Chapter 20.
82
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 83
Getting Started with SolidWorks
The names of the standard planes are also template-specific. For example, the standard planes may be named Front, Top, and Side; or XY, XZ, and ZY; Plane1, Plane2, and Plane3; or North Plan, East or Elevation Plan, and Side for different uses.
Locating Templates You can establish the templates folder at Tools ➪ Options ➪ File Locations ➪ Document Templates. This location may be a local directory or a shared network location. You can specify multiple folders in the list box, each of which will correspond to a tab in the New Document Advanced interface. Once you specify all of the document properties, custom properties, and other settings the way you want them and you are ready to save the file as a template, click File ➪ Save As and in Files of Type, select Part Templates. SolidWorks prompts you to save the template in the first folder that appears in the File Locations list. You can also create additional tabs on the New dialog box by making sub-folders in the main folder that is specified in the File Locations area. For example, if your File Locations list for Document Templates looks like Figure 3.10, then your New dialog box will look like Figure 3.11.
FIGURE 3.10 The Tools ➪ Options ➪ File Locations list
FIGURE 3.11 The New SolidWorks Document dialog box
83
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 84
SolidWorks Basics
When you add subfolders to either of the locations that are listed in File Locations, SolidWorks creates additional tabs in the New dialog box, as shown in Figures 3.12 and 3.13.
FIGURE 3.12 Additional subfolders added to a File Locations path
FIGURE 3.13 The resulting tabs in the New SolidWorks Document dialog box, based on the subfolders in Figure 3.12
Default Templates You can establish default templates at Tools ➪ Options ➪ Default Templates. The default templates must be in one of the paths that are specified in File Locations. Figure 3.14 shows the Default Templates settings.
FIGURE 3.14 The Tools ➪ Options ➪ Default Templates settings
84
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 85
Getting Started with SolidWorks
As shown in Figure 3.14, the Default Template settings contain two options: Always Use These Default Document Templates, and Prompt User to Select Document Template. These options apply to situations where a template is required by an automatic feature in the software, such as an imported part or a mirrored part. In these situations, depending on the option that you have selected, the system either automatically uses the default template or prompts the user to select a template. If you allow the software to apply the default template automatically, this can greatly speed up program performance. This is especially true in the case of imported assemblies, which would require you to manually select templates for each imported part in the assembly if you selected the Prompt User to Select Document Template option.
PERFORMANCE
Sharing templates If you are administering an installation of a large number of users, or even if there are just a few users working on similar designs, then shared templates are a must. If every user is doing what they think is best, you may get an interesting agglomeration of ideas, but the overall consistency of the company’s documentation may suffer. Standardized templates cannot make users model, assemble, and detail in exactly the same way, but they do create a baseline of consistency in user output. To share templates among several users, you must create a folder for templates on a commonly accessible network location, preferably read-only for users and read-write for Administrators. Then direct each user’s File Locations and Default templates to this location. Problems due to multiple users accessing the same files do not arise in this situation because templates are essentially copied to create a new document, and not used directly. One of the weaknesses of this arrangement is that if the network goes down, users no longer have access to their templates. This can be handled by also putting copies of the templates on the local computers; however, this tends to undermine the original goal of consistent documentation. Users may prefer to use and customize the local templates rather than use the standardized network copies.
CAUTION
CAD administration, and indeed organizing any group of people, always comes down to trusting employees to do the right thing. There is no way to completely secure any system against all ignorance and malice, and so you must rely on having hired people that you can train and trust.
Opening Existing Documents There are many ways to open SolidWorks documents, and you should be familiar with a few of them before we go on. Many of these techniques also apply to other Microsoft-compliant software, and so you may already know them; you may also learn something that you can apply to other applications.
85
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 86
SolidWorks Basics
Opening a document Notice that we have several ways of referring to SolidWorks data. Files is generic enough to cover all three data types, part, assembly, and drawing. You may have already noticed that the word documents is also frequently used. The word documents is often used to reinforce the idea that the data inside the file has some business value to your organization, as well as to separate these files from other more generic files such as settings or favorites. For good or ill, the words are often used interchangeably. You can open SolidWorks documents in many ways, and the same procedures apply, regardless of the type of document. The Open dialog box can be used slightly differently; you can use it to filter for different file types. For example, if SolidWorks Part is listed in the Files of type drop-down menu, then you will only see parts. SolidWorks documents can be opened in the following ways: n From the File ➪ Open menu n Browsing through Windows Explorer and double-clicking the file n Browsing through Windows Explorer and dragging the file into the SolidWorks window n Browsing through Windows Explorer, right-clicking the file, and selecting Open n Using File Explorer in the Task pane to browse to the part n If the document was open recently, selecting it from the Recent File list, either in the File menu or in the Task Pane File Explorer n Selecting Open in SolidWorks from SolidWorks Explorer n Selecting the document from the Start menu, Documents list
Looking inside a SolidWorks document What kind of data is actually stored inside a SolidWorks document? Obviously the feature definitions must be stored, as the settings used to create each feature. The document properties mentioned earlier are also stored in the file. Configuration data and design tables are stored, as well as feature comments, and the Design Journal Word document. Other types of information include Parasolid data for the finished part. Parasolid data is also stored for rollback states and configurations. This is one of the reasons why parts can grow dramatically in size as you work on them. Display information is stored for the thumbnail previews, as well as information that can be read by eDrawings to rotate the parts in 3D. For this reason, the image-quality settings can also cause the file size to jump again, particularly for curvaceous models with a lot of small detail. Photoworks and COSMOS data may also be stored in the parts, depending on settings. Increasing file size is not necessarily a bad thing, as long as there is a way to reduce the size again. In many situations, the increase in file size is a result of the file storing information for later use, rather than recalculating it again when it is needed. This is particularly true with rollback states and configurations. As a result, the larger file sizes are intended to improve performance.
PERFORMANCE
The one situation in which performance is adversely affected by file size is when files must be transferred over limited-bandwidth connections. A Zipped-down 200MB file takes time on both ends, first to upload and then to download.
86
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 87
Getting Started with SolidWorks
Assembly files store information such as the paths to all of the referenced parts, and the part configuration that is used. Assembly configuration data is also stored, with component colors, display states, exploded views, and mates. Assembly features must also be stored, along with in-context reference information. Any Smart Fasteners or component patterns are also defined in the assembly document. Lightweight assemblies actually store the part display data in the assembly file, and so for assemblies with a lot of parts, this can require a sizeable amount of information. Flexible subassemblies cause the subassembly mate to be solved in the upper-level assembly, and so the flexible subassembly mates must also be stored in the assembly. Of course, because the Drawing document is the top of the food chain, these documents tend to become the biggest, particularly when several section, broken-out section, or detail views are added.
Microsoft Shadow Data If you pay close attention to the size of your files after you save them, you may notice that SolidWorks files alternately double or halve in size. What is happening is that SolidWorks makes a copy of the data within the file, which effectively doubles the file size. When you perform a Save As function, the size may return to normal. However, this technique does not continue to cut the file size in half every time you do it. Under normal circumstances, files range between the normal file size and twice the normal file size. It should also be noted that the file size reduction is not permanent, and the file size is likely to double again the next time you save it.
NOTE
This is not the same as Microsoft Volume Shadowing, which is a server-based drivecopying technique.
Using the Save As command can seriously affect file management. Save As replaces referenced files if the referencing assembly or drawing document is open when you save a referenced part using Save As. This technique is often used by applying the Save As command and keeping the filename the same.
CAUTION
As you can see, a lot of information is stored in the SolidWorks files, but with good reason. However, there are also some ways to reduce the file size beyond the Save As technique.
Understanding file references SolidWorks assemblies and drawings do not contain any geometry aside from sketches and assembly features; they only display geometry that is ultimately created in part documents. When you open an assembly, the assembly is in turn opening one, or several, or several thousand other part files. In the CAD industry, this is known as associativity. SolidWorks is said to be bi-directionally associative because if you change a part in the assembly window, the part updates, and if you change it in the part window, the assembly updates. This associativity also holds true for drawings.
CROSS-REF
In Chapters 16 and 21, we discuss making changes to part documents from assembly and drawing windows, respectively.
When an assembly opens file references — which may be parts or other assemblies (subassemblies) — you might think that there is some magic and infallible formula that never fails. Of course, you would be wrong if you thought this. To find referenced files, SolidWorks actually goes through a well-defined (if poorly understood) search routine.
87
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 88
SolidWorks Basics
Reducing File Sizes
S
olidWorks files can become immense. By immense, I mean any single file that is over 100MB. This happens more often than you might think, especially in large parts that are highly detailed and with many small radius faces. I do not recommend becoming overly concerned about the size of files that are sitting on a local hard drive and being accessed regularly. It does not help you to try to control files that are going to grow in size anyway. Generally, reducing file size (except for the shadow data) means that the data is going to need to be recalculated at some point, and so it actually slows you down. However, if you are working across a network, or worse yet, across a VPN (virtual private network) or the Internet, you have a more valid concern. The cost of hard drive space is cheap compared to the cost of Internet bandwidth.
CAUTION
Given some of the information above, several techniques exist that can help you control file sizes:
n Save As: As noted earlier, a Save As can remove the shadow data, potentially reducing the file size by half.
n Forced rebuild: When things just simply look wrong with your file, one technique that often sets them right is the forced rebuild. You can apply this command only by pressing Ctrl+Q; there is no other way to access it. It goes through the SolidWorks document and recalculates everything, whether or not SolidWorks thinks it needs to. This is just a way to force everything to be updated, and it sometimes catches errors or eliminates extra data. Early versions of SolidWorks 2007 required a forced rebuild to get rid of extraneous data caused by rollback states.
n Enclosing a part in a Box: This solution probably sounds strange to you, but if you enclose a part in an extruded rectangle, then you are reducing two different sources of file size, the preview and the Parasolid body data. A rectangle is better than a circle, because graphics data is stored as triangles. Flat rectangular faces require only two triangles, but curved faces, especially at high display accuracy, can require hundreds or thousands of triangles. Curve faces also require more data to describe than flat faces.
n Removing configuration data: If you are following this book in a linear way, from the beginning to the end, then you may not yet have read about configurations or some of the other more advanced topics; however, they must be included in the discussion on file sizes. SolidWorks saves body data for each configuration, and so with a lot of configurations, you are going to have a very large file size. If you need to transfer a part across the Internet, it is best to remove any unnecessary configuration data from parts and assemblies. Another technique is to auto-create a Design Table, save the table externally, and then delete all of the configurations. The configurations can then be recreated from the Design Table when needed.
n Changing the display to HLR mode: HLR (hidden line removed) display mode is a wireframe display, which does not have the shaded display data.
88
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 89
Getting Started with SolidWorks
n Minimize the window, push the part off the screen, and save: This is another attempt to reduce the display data that is saved with the part or assembly. Starting with SolidWorks 2007, the software now has an internal routine for creating preview thumbnails. When you save with the part in any orientation or even off of the screen — or worse yet, when the part is last saved from an assembly document where no part-only preview is available — SolidWorks internally takes a snapshot of the part from an isometric view, zoomed to fit the thumbnail image, to use as the thumbnail preview.
Whenever I ask people where they think that an assembly first looks for referenced files, they usually respond that the assembly should look for the files in the same place it found them when the assembly was last saved, or something to that effect. Intuitively, this answer makes a lot of sense, but again, it is incorrect. This actually turns out to be number 8 (of 13) on the list of places that it looks. The first place that it looks is to see if there are currently any other documents open with the same name. This means that you cannot have two different parts called Cover.sldprt open at the same time in a single session of SolidWorks. This is a basic file management concept that you need to understand early on: files need to have unique names. Whether it is a copy of the original or a completely different file with the same name, you need to be careful not to have duplicate filenames, especially as your assemblies become larger and make more use of subassemblies. This means that if you have a large machine with 4,000 unique parts, they all must have different names. From the start, you should use unique filenames. This usually means including some sort of a sequential number in the filename. Descriptive names are popular, but often cause conflicts due to naming issues; for example, how many covers do you have in a typical assembly?
BEST PRACTICE
The second place SolidWorks looks for referenced files is a location that you specify in Tools, Options, File Locations, Referenced Documents. As a result, if you do have multiple files with the same name, you can force SolidWorks to look in a particular location.
Using Visualization Tools One of the most important skills in SolidWorks is manipulating the view. This is something users do more frequently than any other function in SolidWorks, and so learning to do it efficiently and effectively is very important.
Changing the view Whether you look at it as rotating the model or rotating the point of view around the model, view manipulation is an important skill to master in SolidWorks. The easiest way to rotate the part is to hold down the middle mouse button (MMB) or the scroll wheel, and move the mouse. If your mouse does not have a middle button or a scroll wheel that can be used as a middle mouse button, then you can use the Rotate View icon on the View toolbar.
89
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 90
SolidWorks Basics
Some mouse drivers change the middle button or scroll-wheel settings to do other things. Often, you can disable the special settings for a particular application if you want SolidWorks to work correctly and still use the other functionality. For example, the most common problem with mouse drivers is that when the model gets close to the sides of the graphics window and the scroll bars engage, the middle mouse button suddenly changes its function. If this happens to you, you should change the function of the middle mouse button to “Middle Mouse Button” from its present setting.
TIP
Arrow keys The arrow keys rotate the view: n Arrow: Rotate 15 degrees (you can customize this setting through Tools ➪ Options ➪ View Rotation) n Shift-arrow: Rotate 90 degrees n Alt-arrow: Rotate in a plane flat to the screen n Ctrl-arrow: Pan
Middle mouse button The middle mouse (MMB) button or scroll wheel has several uses in view manipulation: n MMB alone: Rotate n Click on edge, face, or vertex with MMB, and then drag MMB: Rotate around selected entity n Ctrl-MMB: Pan n Shift-MMB: Zoom n Alt-MMB: Rotate in a plane flat to the screen
Using the View toolbar The View toolbar, shown in Figure 3.15, contains the tools that you need to manipulate the view in SolidWorks. Not all of the available tools are on the toolbar, and so they are all described here. You can use these tools with models but not drawings.
FIGURE 3.15 The View toolbar
90
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 91
Getting Started with SolidWorks
Zoom To Fit: Resizes the graphics window to include everything that is shown in the model. You can also access this command by pressing the F key. Zoom To Area: When you drag the diagonal of a rectangle in the display area, the display resizes to fit it. Zoom In/Out: Drag the mouse up or down to zoom in or out, respectively. You can also access this command by holding down the Shift key and dragging up or down with the MMB. Zoom To Selection: Resizes the screen to fit the selection. You can also access this command from the right-mouse button, or RMB, on the FeatureManager. For example, if you select a sketch from the FeatureManager and click Zoom to Selection, the view positions the sketch in the middle of the screen and resizes the display to match it. The view does not rotate with Zoom to Selection. There is a reciprocal function that enables you to find an item in the tree from graphics window geometry. If you right-click a face of the model, then you can select Go To Feature in Tree, which highlights the parent feature.
TIP
Rotate View: Enables you to orbit around the part or assembly using the left-mouse button. You can also access this command by using the MMB without the Toolbar icon. Pan: Scrolls the view. You can also access this command by holding down the Ctrl key and dragging the MMB without using the Toolbar icon. 3D Drawing View: Enables you to rotate the model within a drawing view to make selections that would otherwise be difficult or impossible. Standard Views flyout toolbar: The Standard Views toolbar will be discussed later in this chapter. The flyout enables you to access all of the Standard Views tools. Wireframe: Displays the model edges without the shaded faces. No edges are hidden. Hidden Lines Visible (HLV): Displays the model edges without the shaded faces. Edges that would be hidden are displayed in a font. Hidden Lines Removed (HLR): Displays the model edges without the shaded faces. Edges that are hidden by the part are removed from the display. Shaded with Edges: The model is displayed with shading, and edges are shown using HLR. Edges can either be all a single color that you set in Tools, Options, Colors (typically black), or they can match the shaded color of the part. Shaded: The model is displayed with shading, and edges are not shown. Shadows in Shaded Mode: When the model is displayed shaded, a shadow displays “under” the part. Regardless of how you rotate the model, when Shadows are initially turned on, the shadow always starts out parallel to the Standard plane that is closest to the bottom of the monitor. As you rotate the model, the shadow moves with it. If Shadows are turned off and then back on again, they again display parallel to the standard plane that is closest to the bottom of the monitor.
91
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 92
SolidWorks Basics
Section View: Sections the display of the model. Figure 3.16 shows the Section View command at work. You can use up to three section planes at once. Solid models and assemblies can be sectioned, but surface models cannot. You can use the spin boxes, enter numbers manually, or drag the arrows that are attached to the section planes to move the section through the model. Section planes can also be rotated by dragging the border of the plane.
FIGURE 3.16 The Section View tool
Clicking the check mark icon in the Section View PropertyManager enables you to continue working with the sectioned model, although you may not be able to reference edges or faces that are created by the section view. It is only a displayed section; the actual geometry is not cut.
NEW FEATURE
Starting with SolidWorks 2007, you can save the section view to an annotation view for later use in a drawing.
RealView: Creates a more realistic reflective or textured display for advanced material selections. This feature does not work with all graphics hardware, so check the SolidWorks Web site to see if it supports your hardware. The following toolbar buttons are not on the View toolbar by default, but you can add them if you want:
92
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 93
Getting Started with SolidWorks
Camera View: Views the model through a Camera. You can use Cameras for: n Viewing the model from a particular point of view. n Creating renderings with perspective and depth-of-field (focus) blur; this feature is only available when PhotoWorks is added in. n Animating the position and target of the point of view in an animation; this feature is only available when Animator is added in. Cameras are created through the RMB menu on the Lights and Cameras folder in the FeatureManager, as shown in Figure 3.17.
FIGURE 3.17 Adding a new Camera
When you add a Camera, an interface displays in the PropertyManager, as shown in Figure 3.18. In this interface, you can position the Camera object by dragging the triad, and you can resize the Field of View box by dragging the border. In the graphics window, you can use the left panel to target and position the Camera, while the right panel shows the view through the Camera. The Depth of Field panel of the Camera PropertyManager is not shown because it requires that PhotoWorks be added in. There are three methods to switch the graphics window to the Camera view: n Through the View Orientation dialog box (accessed through the spacebar) n Through the View Orientation pop-up (in the lower-left area of the graphics window) n Through the RMB menu on the Camera in the Lights and Cameras folder in the FeatureManager
93
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 94
SolidWorks Basics
FIGURE 3.18 Camera Options and Interface
Triad Field of View box
When you switch the view to the Camera view, the regular Rotate View command does not function. Rotating the view means moving the Camera. There are two ways to move the Camera: n Edit the Camera properties and reposition the Camera by dragging the triad n Use the Turn Camera tool to rotate the view while looking through the Camera Turn Camera: Allows you to rotate the view when looking through the Camera without editing the Camera properties. Draft Quality HLR/HLV: Toggles between low-quality (draft) and high-quality edge HLR or HLV display. This affects display speed for complex parts or large assemblies. When in draft-quality mode, edge display may be inaccurate. Perspective: Displays the model in perspective view without using a Camera. If you want to create a perspective view on a drawing, you must create a custom view in the View Orientation dialog box with the Perspective tool turned on. Perspective can be adjusted through View ➪ Modify ➪
94
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 95
Getting Started with SolidWorks
Perspective by adjusting the relative distance from the model to the point of view. Relative distance is measured by the size of the bounding box of the model, and so if the model fits into a box roughly 12 inches on a side, and the perspective is set to 1.1, then the point of view is roughly 13 inches from the model. For more accurate perspective, you can use a Camera. Curvature: A geometrical analysis tool that applies a color gradient to the part, based on the local curvature. You can also apply curvature display to individual surfaces through the RMB menu. With some hardware, curvature display can take more time to generate for complex models. Settings in Tools ➪ Options ➪ Performance can greatly affect rebuild speed if curvature display data is regenerated for each part rebuild. You should leave this setting at the default setting, which is Only On Demand.
PERFORMANCE
Zebra Stripes: Another geometrical analysis tool that helps you to visualize the quality of transitions between faces across edges. Zebra Stripes simulates putting a perfectly reflective part in a room that is either cubic or spherical and where the walls are painted with black-and-white stripes. In high-end shape design, surface quality is measured qualitatively by using light reflections from the surface. Reflecting stripes makes it easier to visualize when an edge is not smooth. The three cases that Zebra Stripes can help you identify are as follows (see Figure 3.19): n Contact: Surfaces intersect at an edge, but are not tangent across the edge. This condition exists when stripes do not line up on either side of the edge. n Tangency: Surfaces are tangent across an edge, but have different radius of curvature on either side of the edge (non-curvature continuous). This condition exists when stripes line up across an edge but the stripe is not tangent across the edge. n Curvature Continuity: Surfaces on either side of an edge are tangent and match in radius of curvature. Zebra Stripes are smooth and tangent across the edge.
FIGURE 3.19 Zebra Stripes
A
B
C
95
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 96
SolidWorks Basics
In Figure 3.19, the Zebra Stripes in example A do not match at all. This is clearly the non-tangent, contact-only case. Example B shows that the stripes match in position going across the indicated edge, but they change direction immediately. This is the tangent case. Example C shows the stripes flowing smoothly across the edge. This is the curvature continuous case. You can use the remaining icons in the View toolbar to toggle the display of various types of entities from reference geometry to sketches. The following images identify the icons:
View Planes View Axes View Temporary Axes View Origins View Coordinate Systems View Curves View Sketches View 3D Sketch Planes View 3D Sketch Dimensions View All Annotations View Points (refers to Reference Points) View Routing Points (refers to points for the Routing add-in) View Parting Lines (refers to Mold Tools parting lines) View Lights (refers to the light icons, not the illumination from the light) View Cameras View Sketch Relations (this is a good candidate for a hotkey)
96
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 97
Getting Started with SolidWorks
View Orientation Accesses the View Orientation dialog box, shown in Figure 3.20, which contains all of the standard named views, such as Front, Top, and so on. You can also activate View Orientation by pressing the spacebar.
FIGURE 3.20 The View Orientation dialog box
The View Orientation dialog box contains the following controls: Push Pin: Keeps the dialog box active. New View: Creates a new custom-named view (the Wiley view was created this way). Update Standard Views: Sets the current view to be the new Front view; all other views update relative to this change. This also updates any associated drawing views, but does not move any geometry or change plane orientation. Reset Standard Views: Resets the standard views so that the Front view looks normal to the Front plane (Plane1, XY plane). View Orientation can also be manipulated from two other locations: the Standard Views toolbar, which is discussed later in this chapter, and the View Orientation pop-up, shown in Figure 3.21. This function allows you to select the orientation or the arrangement of viewports. The pop-up also displays any existing Cameras, which are described earlier in this section. Previous View (undo view change): You can access this tool using the default hotkey Shift+Ctrl+Z.
97
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 98
SolidWorks Basics
FIGURE 3.21 The View Orientation pop-up
View Orientation pop-up
The Standard Views toolbar We have already mentioned the Standard Views flyout on the View toolbar, but here we will describe the tools that it contains in detail. Figure 3.22 shows the Standard Views toolbar in its default configuration.
FIGURE 3.22 The Standard Views toolbar
By default, the Standard Views toolbar contains the View Orientation button, a tool from the View toolbar. The View Orientation button is discussed in detail earlier in this section. Normal To has three modes of operation: n First Selection: Click a plane, planar face, or 2D sketch. When you click Normal To, the view reorients normal to the selected plane, face, or sketch, and zooms to fit the model in the view. This method is shown in Figure 3.23.
98
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 99
Getting Started with SolidWorks
FIGURE 3.23 The result of using Normal To on the end rib angled face
Selected face
n Second Selection: Click Normal To a second time. The view rotates 180° to display the opposite direction. n Third Selection: After making the first selection, Ctrl-select another planar entity. The second entity is rotated to the top. This method is shown in Figure 3.24.
FIGURE 3.24 Using Normal To with Second Selection to define the top
First selection Second selection
99
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 100
SolidWorks Basics
Annotation views Annotation views enable you to group annotations that were made in the 3D model into views that will be used on the drawing. They can be displayed under the Annotations folder in the FeatureManager for parts and assemblies. Annotation views can be created either automatically, when 3D annotations are added, or manually. An Unassigned Items annotation view acts as a catchall for annotations that are not assigned to any particular views. In the 3D model, you can use the views to reorient the model and display annotations. As mentioned earlier, annotation views can also capture a model section view to be shown in a drawing view. The Annotation views are shown for the Chapter3SampleCasting part in Figure 3.25.
FIGURE 3.25 Annotations views for Chapter3SampleCasting.sldprt
Using color and optical properties Both color and transparency can be very effective tools to help you visualize design geometry. Color can be used in many ways, including coloring certain types of features that need special treatment, such as reamed holes or polished surfaces, or features created by secondary operations after molding or casting the base part. The tool that you can use for controlling color is the Color button from the Standard toolbar, both of which are discussed in Chapter 2. Figure 3.26 shows the Color and Optics interface.
Color hierarchy One of the things that confuse many users about applying color is that colors can be applied on many levels, and may override or be overridden by other colors. This means that in a part, a color may be applied to a face, a feature, a body, or the entire part. (If you are reading this book from beginning to end, then you will notice that several of these entity types have not yet been discussed.) There is a specific hierarchy to this coloring scheme, as follows: n Part: When you apply color or optical properties at the level of the part (the name of the part shows in the Color and Optics PropertyManager), any other entity color will override it. n Body: You can assign Solid or Surface bodies a color that overrides the part color. n Feature: When a feature is selected from the FeatureManager, the applied color goes to the feature. The selection box has selection filter buttons to control the type of entity that is selected.
100
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 101
Getting Started with SolidWorks
n Face: If you click on a part in the graphics window, you select a face. The face may be part of a part, a feature, or a body. Face colors override all other part-level colors. n Component: When you use a part or subassembly in an upper-level assembly, it is considered a component. You can apply colors to a component that override all other applied colors. n Automatic color changes: Some color changes are automatic; for example, when editing parts in the context of an assembly, they can change colors or become transparent, which overrides everything else. For complex surfaces, surface transition quality is often measured by reflections, and so setting up a reflective model can be key to finding shape imperfections. In lieu of reflective RealView materials, using lights with specularity can help you to evaluate curved surfaces, although it is generally not useful for flat faces.
Other entity colors You can color other entities in addition to the 3D shaded model. Curve entities (such as a helix or projected curve) can be colored in addition to sketches. You can only view sketch colors when the sketch is closed and shown, because when the sketch is open, the entity colors have special significance for dealing with the sketch status.
FIGURE 3.26 The Color and Optics interface
101
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 102
SolidWorks Basics
The Display pane The Display pane flies out from the right side of the FeatureManager and displays a quick list of which entities have colors, materials, or textures assigned. It also shows hidden parts or bodies for assemblies and multibody parts. The Display pane is shown in Figure 3.27. You may notice that it does not display colors for faces, and it does not enable you to change anything from the Display pane; it just keeps and displays the record of where the color or optical properties were assigned. We will revisit the Display pane again in Chapter 12 to see how it is used in assemblies.
Automatic colors The settings found at Tools ➪ Options ➪ Document Properties ➪ Colors can be used to automatically color certain types of features with specific colors. For example, all Shell features can be colored red as they are created.
TIP
I find this functionality particularly useful with surface features. I have surface features set to show up as yellow, which to me sets the surfaces apart from the solids.
CAUTION
Certain types of surface features do not follow the automatic feature color settings. This is a bug that has been reported and exists as late as 2007 sp2.1.
FIGURE 3.27 The Display pane in action
Tutorial: Creating a Part Template This simple tutorial guides you through the steps of making a few standard part templates for use with inch and millimeter parts. It also guides you through the creation of some templates for a couple of materials. 1. Select Tools ➪ Options ➪ System Options ➪ File Locations, and then select Document Templates from the Show Folder For drop-down list. 2. Click the Add button to add a new path to a location outside of the SolidWorks installation directory; for example, D:\Library\Templates.
102
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 103
Getting Started with SolidWorks
3. Click OK to close the dialog box and accept the settings. 4. Select File ➪ New. 5. Create a new Part document, selecting any template if you are using the Advanced interface. 6. Select Tools ➪ Options ➪ Document Properties ➪ Detailing. 7. Ensure that the ANSI standard is selected. 8. Change to the Units page. 9. Change the unit system to IPS, inches, with 3 decimal places, using millimeters as the dual units, with 2 decimal places. Set angular units to Degrees with 1 decimal place. 10. Change to the Grid/Snap page. 11. Turn the Display grid setting to OFF. 12. Change to the Image Quality page. 13. Move the slider two-thirds of the way to the right, so that it is closer to the High setting. Ensure that the Save Tessellation With Part Document option is ON. 14. Click OK to save the settings and exit the Tools, Options dialog box. 15. RMB click the Materials entry in the FeatureManager, and select 1060 Alloy from the list. 16. Select File ➪ Properties, and click the Custom tab. 17. Add a property called material of type Text. In the Value/Text Expression column, click the down arrow and select Material from the drop-down list. Notice that the Evaluated Value shows 1060 Alloy. 18. Add another property called description and give it a default value of Description. At this point, the window should look like Figure 3.28.
FIGURE 3.28 Setting up custom properties
19. Click OK to close the Summary Information window. 20. Change the names of the standard planes by clicking them twice slowly or by clicking once and pressing the F2 key. (Selecting Properties from the RMB menu also enables you to edit the name of a sketch or feature.) Rename them to Front, Top, and Side, respectively. 21. Ctrl-select the three planes from the FeatureManager, RMB click, and select Show. 22. From the View menu, ensure that Planes is selected.
103
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 104
SolidWorks Basics
23. RMB click the Front plane and select Insert Sketch. 24. Select the Line tool, and click and drag anywhere to draw a line. 25. Select the Smart Dimension tool and click the line; then click in the graphics window to place the dimension. If you are prompted for a dimension value, press 1 and click the check mark icon, as shown in Figure 3.29.
FIGURE 3.29 Drawing a line and applying a dimension
26. Press Esc to exit the Dimension tool, RMB click the displayed dimension, and select Link Value. 27. Type thickness in the Name text box, and click OK. 28. Press Ctrl-B (rebuild) to exit the sketch, select the sketch from the FeatureManager, and press Delete. This exercise of creating the sketch and deleting it was done only to enter the link value “thickness” into the template. Once this is done, every part made from this template, which uses an Extrude feature, will have a check box for Link to Thickness, which allows you to automatically establish a thickness variable for each part that you create. This is typically a sheet-metal part feature, but it can be used in all types of parts.
NOTE
29. Click File ➪ Save As, and select Part Template from the drop-down list. Ensure that it is going into your template folder, give it an appropriate name, and then click Save. 30. Edit the material that you applied to change it from 1060 Alloy to Plain Carbon Steel, and save it as another template with a different name. 31. Change the primary units to millimeters with 2 places, and save it as a third template file. 32. Exit the file.
104
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 105
Getting Started with SolidWorks
Tutorial: Visualization Techniques Visualization is a key factor in SolidWorks. Whether it is for a presentation of your design to customers or management or simply checking the design, it is important to be able to see the model in various ways. This tutorial guides you through using several tools and techniques. 1. If the part named Chapter3Sample.sldprt is not already opened, then open it from the CD-ROM. If it is open and changes have been made to it, then click File ➪ Reload ➪ OK. 2. Practice using some of the controls for rotating and zooming the part. In addition to the View toolbar buttons, you should also use Z and Shift-Z (Zoom Out and In, respectively), the arrow keys, and the Ctrl-, Shift-, and Alt-arrow combinations. 3. Use the MMB to select a straight edge on the part, and then drag with the MMB. This rotates the part about the selected entity. Also apply this technique when selecting a vertex and a flat face. 4. Select the name of the part at the top of the FeatureManager. 5. Click the Color button from the Standard toolbar. 6. Click the color you want in the Favorite panel. The model should change color. If you click and drag the cursor over the colors, the model changes color as you drag over each new color. Figure 3.30 identifies some of the buttons.
FIGURE 3.30 The Color and Optics interface elements
Select Face Select Surface Select Body Select Features
Create New Swatch Add Selected Color Remove Swatch
105
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 106
SolidWorks Basics
7. If the Color Properties panel is not expanded, click the double arrows to the right to expand it. Select the colors you want from the continuous color map. Again, click and drag the cursor to watch the part change color continuously. 8. Create a swatch. In the Favorite panel, select the Create New Swatch button and call the new swatch color file BibleColors. 9. Select a color from the Color Properties continuous map; the Add Selected Color button becomes active. Clicking the button adds the color to the swatch palette. You can add several colors to the palette to use as favorites later on. You will be able to access these colors again later by selecting BibleColors from the drop-down list in the Favorite panel. You can transfer the colors to other computers or SolidWorks installations by copying the file BibleColors.slddclr from the <SolidWorks installation directory>\lang\english folder (or the equivalent file for your installed language).
TIP
10. In the Optical Properties panel, move the Transparency slider to the right, and watch the part become transparent. 11. To prevent the Color and Optics window from closing after every change, click the pushpin icon at the top of the window. 12. Click the green check mark icon to accept the changes; note that with the push-pin icon selected, the window remains available. 13. Expand the flyout FeatureManager in the upper-left corner of the graphics window, as shown in Figure 3.31, so that all of the features in the part are visible.
FIGURE 3.31 The Flyout FeatureManager
14. Select the features Extrude1, Fillet7, and Fillet6 from the FeatureManager so that they are displayed in the Selection list of the Color and Optics window. Select a color from the BibleColors swatch palette that you have just created. 15. Click the check mark icon to accept the changes and clear the Selection list. 16. Select the inside face of the large cylindrical hole through the part, and assign a separate color to the face.
106
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 107
Getting Started with SolidWorks
17. Click the check mark icon to accept the changes, and click the red X icon to exit the command. 18. Expand the Display pane (upper-right area of the FeatureManager). You should see color and transparency symbols for the overall part, and color symbols for three features. There is no indication of the face color that is applied. 19. Remove the colors. Open the Color and Optics window again, re-select the three features (Extrude1, Fillet7, and Fillet6), and click the Remove Color button below the Selection list. Do the same with the colored face. Return the part transparency to fully opaque. 20. Click the check mark icon to accept the changes. 21. Change the edge display to Shaded (without edges). Then change to a Wireframe mode. Finally, change back to Shaded With Edges. 22. Now select View ➪ Display ➪ Tangent Edges as Phantom. Figure 3.32 shows the difference between Tangent Edges Visible, as Phantom, and Removed settings.
FIGURE 3.32 Tangent Edge display settings for a shaded model
107
3
08_080139 ch03.qxp
Part I
3/26/07
3:29 PM
Page 108
SolidWorks Basics
Using the Tangent Edges as Phantom setting is a quick and easy way to look at a model to determine whether or not face transitions are tangent. It does not help to distinguish between tangency and curvature continuity; you need to use Zebra Stripes for that.
TIP
23. Switch back to Shaded display. 24. If you do not have a RealView-capable computer, then skip this step. Ensure that the RealView button in the View toolbar is depressed. RMB click the Material folder in the FeatureManager. Select Edit Material, and then select Steel, AISI 304. Rotate the part. Notice that the finish is semi-reflective. Click the check mark icon to accept the change. 25. If the Texture button is not on your Standard toolbar, use Tools ➪ Customize ➪ Commands to add it to the toolbar. 26. Turn the part over, select the bottom face, and apply a texture of Steel, Cast, Cast Rough. The rest of the part should retain the semi-reflective surface, as shown in Figure 3.33. Click the check mark icon to accept the change.
FIGURE 3.33 Applying a material to a part
27. Click the Section View button on the View toolbar. Drag the arrows in the middle of the section plane back and forth with the cursor to move the section dynamically through the part, as shown in Figure 3.34. 28. Click the check box next to the Section 2 panel name, and create a second section that is perpendicular to the first. 29. Click the green check mark icon to accept the section. Notice that while in the Section View PropertyManager, the RealView material does not display, but once you close the dialog box, RealView returns.
108
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 109
Getting Started with SolidWorks
FIGURE 3.34 A section view
Summary Learning to manipulate the view is essential to being able to interpret the visual data on the screen. As a result, you need to be familiar with opening and viewing SolidWorks documents before we can discuss the modeling aspects of the software. When you start using SolidWorks, several resources are available to help you learn the basic tasks. There are also some important options that you need to select up front, when using the software for the first time. Properly setting up templates can save you a lot of time and automate other tasks in the future, particularly drawings and PDM data entry. Customizing your SolidWorks installation and knowing which files are and are not important is also key to your role as Administrator.
109
3
08_080139 ch03.qxp
3/26/07
3:29 PM
Page 110
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 111
Working with Sketches
T
his is where the fun begins, or begins to begin. To me, training animals has always been fun, especially when the animal begins to respond to my instructions. Learning SolidWorks is like working with an animal that has already been trained. You know it is supposed to respond to you in certain ways, but there is always this little thrill of having communicated with something outside of yourself when it actually responds with a predicted behavior. This is not to say that it is surprising; it is just somehow a little thrilling. SolidWorks programmers have created an animal that responds to your input with intelligence and comprehension. So far in this book, we have looked mainly at settings and setup, which is pretty mundane business. However, here we begin to build models, simple at first, but gaining in complexity and always demonstrating new techniques and features that build your modeling vocabulary. Beyond this, we move into putting the parts together into assemblies, which helps to make the “pretty pictures” look like something useful. Finally, we use the parts and assemblies to create drawings. Several basic facts about sketches may be helpful before we start. While a part may have many sketches, only one sketch can be open at a time. This is due in part to the history-based nature of the software because every entry in the FeatureManager tree must be edited in the order in which it sits in the tree.
While you can create both 2D and 3D sketches, you will use 2D sketches most of the time. When referring to a generic sketch, a 2D sketch is always assumed. You will use 3D sketches in specific situations, and they will be explicitly called for when needed.
CROSS-REF
We discuss 3D sketches in detail in Chapter 31.
111
IN THIS CHAPTER Opening a sketch Identifying sketch entities Inferencing in Sketch Sketch settings Sketch blocks Tutorial: Learning to use sketch relations Tutorial: Using Blocks and Belts
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 112
SolidWorks Basics
When you open a sketch, several tools become unavailable. For example, you cannot apply a Fillet feature while a sketch is open. Conversely, there are several things that you cannot do until you open a sketch. When I used to teach SolidWorks classes for a reseller, I had only one rule: you were not allowed to throw the monitor out the window because of frustration until you checked to see if you were in or out of Sketch mode and if the selection filter was turned on. These features are two very common sources of frustration for new users. There are several indicators that let you know when you are in Sketch mode: n The top bar of the SolidWorks window displays the text, Sketch X of Part Y. n The lower-right corner of the status bar displays the text, Editing Sketch X. n The Confirmation Corner displays a sketch icon in the upper-right corner of the graphics window. n The Sketch toolbar button now displays the text, Exit Sketch, and is pressed in. n The red sketch Origin displays. n If you are using the grid, it displays only in Sketch mode. While most users find the sketch grid to be annoying and distracting, when teaching, I always used the grid to remind students when they were in Sketch mode. If you find that you forget or would like a visual cue, the sketch grid is a useful, if less than fashionable, option.
Opening a Sketch There are several ways to open a new sketch in SolidWorks: n Click a sketch entity toolbar button from the Sketch toolbar; SolidWorks prompts you to select a sketch plane. When you select the plane, the sketch opens. n Preselect a plane or planar face and then click either a sketch entity button or the Sketch button. n Right-mouse button (RMB) click a plane or planar face and select Insert Sketch. You can open existing sketches in several ways: n RMB click a sketch in the FeatureManager or graphics window, and select Edit Sketch. n Select a sketch from the FeatureManager or graphics window, and click the Sketch button on the Sketch toolbar. n Double-click a sketch with the Move/Size Features tool active.
112
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 113
Working with Sketches
Identifying Sketch Entities The first step in creating most SolidWorks parts is a sketch. This will usually be a 2D sketch, although 3D sketches are also used and are discussed in Chapter 31. A 2D sketch is simply a collection of 2D lines, arcs, and other elements that lie together on a plane; it usually also contains relations and/or dimensions between the entities. SolidWorks sketch entities include many types, some of which you will use all of the time, and some of which you may not use, even if you spend years working with the software. Here we will identify each entity type so that you see it at least once, and know that it is available if you need it at some point.
The Sketch toolbar The default buttons on the Sketch toolbar are identified first, followed by the rest of the entities that you can access through Tools ➪ Customize ➪ Commands ➪ Sketch. Sketch opens and closes sketches. If you preselect a plane or planar face and then click the Sketch button, SolidWorks opens a new sketch on the plane or face. If you preselect a sketch before clicking the Sketch button, SolidWorks opens this sketch. If you do not use preselection, SolidWorks prompts you to select a plane on which you want to put a new sketch, or an existing sketch to edit. 3D Sketch opens and closes 3D sketches. Smart Dimension can create several types of dimensions, such as horizontal, vertical, aligned, radial, diameter, angle, and arc length. n Horizontal, Vertical, and Aligned: You can create dimensions in three ways, as shown in Figure 4.1: n By selecting a line and placing the dimension n By selecting the endpoints of the line and placing the dimension n By selecting lines at the ends of the line and placing the dimension Selecting the line is the easiest and fastest method. Selecting the lines on the ends is not recommended because if you delete either of the selected lines, the dimension is also deleted. You can use the first and second techniques for the angled line shown in Figure 4.1 to create any of the three dimensions shown. You can do this by dragging the cursor while placing the dimension until the witness lines snap to the orientation you want.
TIP
To lock the orientation of a dimension while moving the cursor to place the actual dimension value, RMB click. To unlock it, just RMB click again.
113
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 114
SolidWorks Basics
FIGURE 4.1 Selection options for linear Smart Dimension
1 2 3
In this case, the third technique locks you into the horizontal orientation because of the orientation of the selected lines. When you select end lines to establish a dimension instead of endpoints, both of the end lines will gain an implied relation that prevents them from moving as you might predict. In the case shown in Figure 4.1, neither of the end lines can be angled unless you remove the dimension.
CAUTION
Another issue that arises for adding dimensions to end lines is that if you delete either of the end lines, the dimension is also deleted. This is not true for the first and second techniques, where as long as the endpoints remain, the dimension also remains.
n Radial: You create the dimension by selecting an arc and placing the dimension. If you want a radial dimension of a complete circle, you must RMB click the dimension after you create it, select Properties, and deselect the Diameter Dimension option, as shown in Figure 4.2. n Diameter: You can create the dimension by selecting a complete circle and placing the dimension. If you want a diameter dimension for an arc, use the Dimension Properties dialog box shown in Figure 4.2 and select the Diameter Dimension option. n Angle: You can create the dimension in one of two ways. If the angle to be driven is between two straight lines, simply select the two straight lines and place the dimension. If you are creating an included angle dimension for an arc where there are not necessarily any straight lines drawn, then with the Smart Dimension tool active, first select the vertex of the angle, and then the two outlying points, as shown in Figure 4.3. n Arc Length: You can create the dimension by selecting an arc and its endpoints with the Smart Dimension tool.
114
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 115
Working with Sketches
FIGURE 4.2 The Dimension Properties interface
FIGURE 4.3 Creating an included angle dimension
Click first
Order unimportant
115
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 116
SolidWorks Basics
Line creates straight lines using one of two methods: n Click-Click: Used for drawing multiple connected end-to-end lines. Click and release the left-mouse button to start the line; each click-and-release ends the previous line and starts a new one. Double-click, press Esc, or deselect the Line tool to end. n Click-Drag: Used to draw individual or unconnected lines. Click, drag, and drop. The first click initiates the line, and the drop ends it. Alternate methods for drawing lines include horizontal, vertical, angle, and infinite lines. The interface for these options displays in the PropertyManager, as shown in Figure 4.4. n Horizontal, Vertical: These settings require you to select a starting point, and an ending vertical or horizontal position. There does not seem to be any compelling reason for you to use this instead of the regular line command. n Angle: Enables you to specify an angle and drag a line at this angle. Again, I can find no compelling reason to use this tool. n Infinite Lines: This is truly puzzling. SolidWorks parts have a working space limited to 1000 meters on a side, centered on the Origin. Infinite lines extend well beyond this, although you cannot draw or dimension a regular line outside of this box. I have not come across a compelling use for this feature, and I am quite sure that it was added only to appease unrepentant AutoCAD users. FIGURE 4.4 The Insert Line PropertyManager interface
Rectangle creates a rectangle by clicking one corner and dragging to the diagonal corner. This action creates four lines with Horizontal and Vertical sketch relations, as appropriate.
116
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 117
Working with Sketches
Circle creates a circle using one of two methods: n Center Creation: Click the center of the circle and drag the radius. The Circle PropertyManager calls this function center creation. n Perimeter Creation: This only creates tangent relations with other entities in the current sketch, and so if you are building a circle from model edges or entities in other sketches, you need to apply the relations manually. SolidWorks calls these functions perimeter creation. To create a circle using this technique, you must select the Perimeter Creation option from the Circle PropertyManager window after clicking the Circle tool. There is also a separate Perimeter Creation toolbar button, and a menu selection for Tools ➪ Sketch Entities ➪ Perimeter Circle. n Tangent to Two Entities: Start the circle with the cursor near one line in the sketch. A Tangent symbol appears by the cursor with a yellow background. Click and drag the diameter to the second tangent entity, where a similar cursor symbol should appear. Release the mouse button and RMB click the green check mark icon. This process is shown in Figure 4.5. n Tangent to Three Entities: Use the process for Tangent to two entities, but omit the RMB click of the green check mark icon. After dropping on the second tangent, drag again to the third tangent entity.
FIGURE 4.5 Creating a perimeter creation circle
117
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 118
SolidWorks Basics
Centerpoint Arc creates an arc by clicking the center, dragging the radius, and then clicking and dragging the included angle of the arc. The first two steps are exactly like the Center-Radius circle. Tangent Arc creates an arc tangent to an existing sketch entity. Depending on how the cursor moves away from the end of the existing sketch entity, the arc can be tangent, reverse tangent, or perpendicular, as shown in Figure 4.6.
FIGURE 4.6 Using the Tangent Arc feature
Original line
Perpendicular
Reverse tangent
Tangent
Another way to create a tangent arc is to start drawing a line from the end of another sketch entity, and while holding the left mouse button, to press the A key, or to return the cursor to the starting point and drag it out again. This method can be difficult to master, but it saves time when compared to any of the techniques for switching sketch tools. 3 Point Arc creates an arc by first establishing endpoints, and then establishing the included arc, as shown in Figure 4.7. Again, this tool also works using the Click-Click or Click-Drag methods.
FIGURE 4.7 Creating a three point arc
Click-Drag
118
Click-Drag
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 119
Working with Sketches
Sketch Fillet creates a sketch fillet in one of two ways. You can either select the endpoint where the sketch entities intersect, or you can select the entities themselves, selecting the portion of the entity that you want to keep. Figure 4.8 illustrates both techniques.
FIGURE 4.8 Creating a sketch fillet
Select lines
Select
Result
Centerline follows the same methods as regular lines, and is also called a construction line in some cases. Other construction entities such as construction circles are not available, but you can create them by selecting the For Construction option in the PropertyManager for any entity.
Sketch Fillets
W
hile the Sketch Fillet tool is easy to use, applies immediately, and may align with your way of working in a 2D program, it is not considered best practice to use sketch fillets extensively. Some reasons for this include:
n Large changes in the size or shape of the rest of the sketch can make the fillets cause the feature built from the sketch to fail.
n SolidWorks (and other parametric programs as well) often has difficulty solving tangent arcs in some situations. You may see them flip tangency or go around 270° instead of just 90°. Using a lot of fillets in a sketch can often cause trouble.
n If you want to remove the fillets temporarily, there is no good way to do this if you have used sketch fillets.
n Sometimes feature order requires that other features, such as draft, come before the fillet. n Sometimes a 2D fillet simply cannot create the required geometry. Fillet features are the preferred method for creating rounds and fillets. The same can be said for chamfers.
119
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 120
SolidWorks Basics
Spline draws a freeform curve. Splines may form either a single closed loop or an open loop. You can draw a spline by clicking each location where you want to add a control point. Figure 4.9 identifies the elements of a spline. The detail image shows the structure of a spline handle.
FIGURE 4.9 The structure of a spline and a spline handle
Control polygon
Spline points
Minimum radius
Inflection point
Combination (direction and magnitude)
Direction handle
Magnitude handle
120
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 121
Working with Sketches
Splines are used mainly for freeform complex shapes in 2D and 3D sketches, although you can also use them for anything that you would use other sketch elements for. Point creates a sketch point. Aside from limited cases of lofting to a point or using a point as a constraint sketch in a Fill feature, sketch points are usually used for reference or for the location of the centerpoint of Hole Wizard features. You can also use the sketch point as a virtual sharp. If two sketch entities do not actually intersect because of a fillet or chamfer, selecting the two entities and clicking the Point tool creates a point at the location where they would intersect if they were extended. This is useful for dimensioning to the sharp. Virtual sharp display is controlled by a Document Property setting that is described in more detail in Appendix B. 3D Sketch Plane creates a plane in a 3D Sketch. I discuss 3D Sketches in more detail in Chapter 31. Add Relation displays a PropertyManager window that allows you to apply sketch relations. This interface appears to be obsolete because it is easier to simply select sketch items and apply relations in the PropertyManager window that appears automatically when you select them; however, there are some subtle workflow-related reasons for using this tool. When the Add Relation PropertyManager is active, you do not need to use the Ctrl key to select multiple entities. You also do not need to clear a selection before making a new selection for the next relation. These two reasons sound minor, but if you have a large number of sketch relations to apply, the workflow goes much more smoothly using this tool than the default method. Display/Delete Relations enables you to look through the relations in a sketch, and sort them according to several categories. From this window, you can delete or suppress relations and replace entities in relations. Quick Snaps flyout allows you to quickly filter types of entities that sketch elements will snap to when you move or create them. To access the tools, click the drop-down arrow to the right of the toolbar button. Mirror Entities mirrors selected sketch entities about a single selected centerline, and applies a Symmetric sketch relation. There is also a Dynamic Mirror function that is described later in this chapter. Convert Entities converts edges, curves, and sketch elements from other sketches into entities in the current sketch. When edges are not parallel to the sketch plane, the Convert Entities feature projects them into the sketch plane. Some elements may be impossible to convert, such as a helix, which would produce a projection that overlaps itself. Sketch entities that are created using Convert Entities get an On Edge sketch relation.
121
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 122
SolidWorks Basics
Offset Entities works like the Convert Entities feature, except that it offsets the sketch to one side or the other of the projection of the original edge, sketch, or curve. Figure 4.10 shows the interface for this command.
FIGURE 4.10 The Offset Entities interface
The options available in the Offset Entities interface are as follows: n Add Dimensions: Constrains offset sketch entities. Instead of the On Edge relations, Offset Entities creates an Offset sketch relation that cannot be recreated manually. n Reverse: Changes the direction of the offset. n Select Chain: Selects continuous end-to-end sketch entities. n Bi-directional: Offsets to both sides simultaneously. n Make Base Construction: If you are offsetting sketch entities within the active sketch, this option converts the original sketch entities to construction sketch geometry. n Cap Ends: Is available only when you have selected the Bi-directional option. Capping the ends with arcs is an easy way to create a slot from a sketch of the centerline. This function works with all sketch entities, and so it is not limited to straight slots. Figure 4.11 shows examples of the Cap Ends option.
CAUTION
122
The Offset Entities command may fail if the offset distance is greater than the smallest radius of curvature, and you are attempting to offset to the inside of the arc.
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 123
Working with Sketches
FIGURE 4.11 The results of using offset entities cap ends
Trim Entities is actually several functions rolled into one, and it is an extremely powerful tool for editing sketches. Trim Entities allows several methods for trimming, as well as extending and deleting sketch entities. Figure 4.12 shows the PropertyManager interface for this function.
FIGURE 4.12 The Trim Entities interface
n Power Trim: Trims by dragging a cursor trail over multiple entities. The entities that you drag the cursor over are trimmed back to the next intersecting sketch entity. Each time you trim an entity, a red box is left behind that remains until you trim the next entity. If you backtrack with the cursor and touch the red box, this trim is undone. This option is best used when you need to trim a large number of entities that are easy to hit with a moving cursor. Figure 4.13 shows the Power Trim feature in action.
123
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 124
SolidWorks Basics
You can also use power trim to extend sketch entities along their paths by dragging the endpoints. Regular dragging can also change the position or orientation of the rest of the entity, but by using the Power Trim feature, you affect only the length.
FIGURE 4.13 The Power Trim feature in action
n Corner: Trims or extends two selected entities to their next intersection. When you use the Corner option to trim, the selected portion of the sketch entities is kept, and anything on the other side of the corner is discarded. Figure 4.14 shows two ways that the Corner option can work.
FIGURE 4.14 Using the Corner option
124
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 125
Working with Sketches
n Trim Away Inside: Trims away selected entities inside a selected boundary. The boundary may consist of a pair of sketch entities or a model face (edges of the face are used as the boundary). Only entities that cross both selected boundaries (or cross the closed loop of the face boundary twice) can be trimmed. This option does not trim a closed loop such as a circle, ellipse, or closed spline. n Trim Away Outside: Functions exactly like the Trim Away Inside option, except that sketch entities outside of the boundary are discarded. The Trim Away Inside and Outside option are illustrated in Figure 4.15.
FIGURE 4.15 Using the Trim Away Inside and Outside options
n Trim to Closest: This is the default setting. Clicking on a sketch entity will: n Trim it back to the next entity if there is only one crossing entity. n Trim between two crossing entities if there are more than one. n Delete the entity if there are no crossing entities. In all cases, the selected section of the entity is removed. The Trim to Closest option can also extend by dragging one entity to another; if an intersection is possible, the first entity is extended to the second entity. Figure 4.16 illustrates how the Trim to Closest option functions. Construction Geometry toggles between regular sketch entities and construction entities. Move Entities enables you to move entities within a sketch by dragging or by keying in XY points. Figure 4.16 shows the simple interface for the Move Entities command. Select the entities to move in the upper box, and the method to move them below.
125
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 126
SolidWorks Basics
FIGURE 4.16 The Move Entities interface
Select is usually used to turn off the previous command. Grid/Snap is used to open the Grid/Snap section of Tools, Options, Document Properties. Parallelogram can be used in two different ways: n To draw a rectangle at an angle, click one corner of the rectangle, and then drag a side connected to that corner. Then click and drag the length of the second direction. n To draw a parallelogram (adjacent sides are not perpendicular, but opposite sides are parallel), draw the first side of the parallelogram in the same way as the first side of the rectangle, but hold down the Ctrl key when dragging the second side; you can set the angle as well as the length. Polygon creates a regular n-sided polygon in the same way as a circle. Click the center and drag the radius. You need to set the number of sides in the PropertyManager before clicking in the graphics window. Perimeter Circle. See Circle mentioned earlier. Ellipse is created by clicking the center, dragging one axis, and then dragging the other axis.
126
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 127
Working with Sketches
Partial Ellipse is created by clicking the center, dragging one axis, dragging the other axis, and then clicking and dragging the included angle of the partial ellipse. The Partial Ellipse feature works like the centerpoint arc. Parabola is created by clicking the location for the Focus, and then dragging the position of the Apex. You then click and drag the included angle of the parabola, as shown in Figure 4.17.
FIGURE 4.17 Drawing a parabola
Focus
Apex
Click and drag
Click and drag
Spline on Surface is used in 3D sketches to draw a freeform spline on any 3D surface. The Spline on Surface feature is constrained to working only on a single face at a time; it cannot bridge between faces. Sketch Text creates editable text in sketches using TrueType fonts. Some fonts produce sketches that are unusable for solid features. Sketch Text may be dissolved into lines and arcs so that you can edit them manually. Figure 4.18 points out the key elements of the Sketch Text interface.
127
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 128
SolidWorks Basics
FIGURE 4.18 The Sketch Text interface
Curve for text to follow
Sketch text Bold, italics, rotate Justification
Spacing Width
Direction and orientation
Intersection Curve in 2D sketches, creates sketch entities where the sketch plane intersects selected faces. In 3D sketches, the Intersection Curve feature creates sketch entities where any types of selected surfaces intersect. This can be an extremely useful tool in many situations. Face Curves applies the underlying U-V isoparameter mesh to a selected face. It is most commonly used as an analysis tool for complex surfaces, but you can also use it to create curves to rebuild faces. Accepting the results by clicking OK creates a separate 3D sketch for each spline. Figure 4.19 shows the original surface and the results of using face curves on a complex lofted surface. Extend extends a sketch entity up to its next intersection with another sketch entity. Split Entities splits a sketch entity into two segments. You can also delete it later to rejoin the entity back into a single segment.
128
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 129
Working with Sketches
FIGURE 4.19 Using face curves on a complex surface
Dynamic Mirror can be used when you preselect a centerline, and Dynamic Mirror is turned on. Any new sketch entity that you draw is automatically mirrored to the other side of the centerline. Rotate Entities rotates selected sketch entities. Scale Entities scales selected sketch entities about a specified point by a specified scale ratio. This function does not scale dimensioned entities, and may remove external sketch relations to complete the task. Copy Entities can copy multiple instances of selected sketch entities. This feature functions like the Move Entities feature. Unfortunately, a combination of the Copy and Rotate features does not seem to exist. Linear Sketch Pattern creates a one- or two-directional pattern of sketch entities. You can define spacing and angles. Figure 4.20 shows the interface and the results of this function. Circular Sketch Pattern creates a circular pattern of sketch entities. You should use sketch patterns as little as possible. For much the same reasons that fillet features are preferred over sketch fillets, pattern features are also preferred over sketch patterns. Sketch patterns are not as editable or as flexible as feature patterns. They solve slowly, especially when you pattern a lot of entities. Best practice is to avoid sketch patterns unless there is no alternative.
BEST PRACTICE
Make Path is intended to help create machine-design motion in sketches, in particular, cam type motion. Although it is helpful, you do not need to make a block of the cam first. You can then RMB click the block and select Make Path. A tangent relation to a path enables a follower to roll around the entire perimeter.
129
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 130
SolidWorks Basics
FIGURE 4.20 The Linear Sketch Pattern interface
Modify Sketch is one of my favorite sketch tools, but it has been falling out of favor in more recent versions of SolidWorks because of the improvement of tools such as Move Sketch. The Modify Sketch feature is flexible and powerful, and enables you to move, rotate, and scale the sketch, as well as mirror about a horizontal or vertical axis or about both axes simultaneously. Figure 4.21 shows the interface, which consists of a dialog box, a special Origin, and a contextsensitive cursor.
FIGURE 4.21 The Modify Sketch interface
130
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 131
Working with Sketches
Both the left- and right-mouse buttons have special functions, which change when the cursor is moved over the three knots on the special Origin. The RMB allows you to mirror or rotate the sketch, and the left-mouse button, or LMB, allows you to move the Origin or move the sketch. This function has some limitations when you use it with sketches that have external relations. Certain functions may be disabled, or a warning message may appear, saying that you need to remove external relations to get a particular function to, well, function. No Solve Move enables the moving of sketch entities without solving any relations in the sketch. If you select this option and you move an entity with relations that would otherwise not allow it to move (such as a collinear relation), then you are prompted with a choice to either delete the existing relation and continue, or to copy the entity without the relation. Sketch Picture is a picture that is placed in the sketch, lies on the sketch plane, and is listed in the FeatureManager that is indented under the sketch. The sketch picture may be suppressed independently from the rest of the sketch, and when the sketch is hidden, the picture is not visible. You can easily move, resize, and rotate sketch pictures, as well as apply a transparent background to them. They are usually used for tracing over or as a planar decal without the need for PhotoWorks. Figure 4.22 shows the controls for manipulating the Sketch Picture feature.
FIGURE 4.22 The Sketch Picture interface
131
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 132
SolidWorks Basics
The Dimensions/Relations toolbar The Dimensions/Relations toolbar has a few tools that we have already seen, but as the name suggests, it also contains tools that will either help you to create or investigate dimensions and sketch relations. Figure 4.23 shows the default toolbar, but in the following pages, we look at all of the available tools that are available through Tools ➪ Customize ➪ Commands ➪ Dimensions/ Relations.
FIGURE 4.23 The Dimensions/Relations toolbar
Smart Dimension is described in the Sketch toolbar section, and is shown in Figure 4.1. Horizontal Dimension applies a dimension to a sketch entity that drives the horizontal distance between the endpoints. Vertical Dimension works like a horizontal dimension, but vertically. Baseline Dimensions are different from most of the dimension tools that you find on the Dimensions/Relations toolbar in that they create only reference dimensions (they are driven, they only measure distances rather than drive them), and they are applicable only in drawing documents. Baseline Dimensions start from a single reference; then, as you select additional references, additional dimensions are stacked, as shown in Figure 4.24.
FIGURE 4.24 Baseline Dimensions on a drawing
132
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 133
Working with Sketches
Ordinate Dimensions are driving dimensions where a set of ordinate dimensions originate from a common zero point. To use these dimensions, simply click a zero location, place the zero dimension, and then click additional points. The dimensions are placed and are automatically aligned to the rest of the dimensions.
NOTE
If a line is not selected as the zero reference entity, the Ordinate Dimension feature defaults to a Horizontal Ordinate.
You can remove Ordinate Dimensions from the common alignment by RMB clicking the dimension and selecting Break Alignment. Ordinate Dimensions will jog automatically if SolidWorks senses that the dimensions are getting too close to one another. You can also jog them manually. After you create the Ordinate Dimension set, you can add to it by accessing the Add to Ordinate command through the RMB menu. All of these options for Ordinate Dimensions are shown in Figure 4.25.
FIGURE 4.25 Options for Ordinate Dimensions
Not all of the listed options are available in the model sketch environment; some are available only in drawings. Horizontal Ordinate Dimensions are simply ordinate dimensions that are forced to drive dimensions in a horizontal direction. Horizontal and Vertical Ordinate Dimensions have the same function as the regular Ordinate, except that they only drive horizontal and vertical dimensions, respectively.
133
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 134
SolidWorks Basics
Chamfer Dimension is another type of dimension that is only driven and only applied in drawing documents. It works by first selecting the chamfered edge, and then selecting the angle reference edge. It produces dimensions like the one shown in Figure 4.26.
FIGURE 4.26 Applying a chamfer dimension
Select first Select second
Auto Dimension also functions only in a drawing. You need to select reference edges for X and Y directions and specify either all edges or only selected edges. SolidWorks then dimensions everything, based on the reference edges. Hole diameters are also dimensioned. While the Auto Dimension feature can clearly save you a lot of time dimensioning parts on a drawing, it does not necessarily use the best dimensioning practice for manufacturing drawings. This tool is best used in situations when baseline dimensions are appropriate.
BEST PRACTICE
Add Relations is described in depth in the Sketch toolbar section. Automatic Relations toggles to enable or disable the automatic creation of sketch relations while sketching. This toggle is also available through Tools ➪ Sketch Settings ➪ Automatic Relations. Automatic relations help you to create intelligent sketches with less manual intervention. Although using them takes a little practice, it is well worth the effort. As with any automatic function, there are times when automatic relations will do things that you do not expect or want. While you are sketching, it is recommended that you watch the cursor and the relations that it automatically applies.
CAUTION
While sketching, symbols appear on the cursor to show that a relation will automatically be created. These symbols have a yellow background, and will apply horizontal, vertical, coincident, tangent, parallel, and perpendicular relations. Figure 4.27 shows two situations where automatic relations are applied — a horizontal and a tangent relation.
134
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 135
Working with Sketches
FIGURE 4.27 Some automatic relations that appear on the cursor
Inferencing in Sketch Although Inferencing and Automatic Relations are often confused, even by experienced SolidWorks users, these functions are not the same. Inferencing refers to the blue dotted lines that display in Sketch mode when the cursor aligns with endpoints, centerpoints, or the Origin. Inferencing does not create sketch relations, with one exception. If the cursor is aligned to one side of the endpoint of another line, and you draw a horizontal line, then an automatic Coincident relation is applied between the line and the endpoint. This also holds true if the cursor starts above or below the point and you draw a vertical line. When the cursor displays a small symbol with a yellow background, this means that an automatic relation is going to be applied. If the relation symbol has a white background, the relation is inferenced, but not applied as an actual sketch relation. The symbols with the blue background are relations that have been applied to existing sketch entities. The symbols look the same, regardless of background color. The following are the symbols for the various inferences, automatic relation cursors, and applied sketch relations. The difference between the three types is simply the background colors, white, yellow, and blue, respectively.
CROSS-REF
These relations are defined in the Sketching with Parametrics section of Chapter 1.
Along X Along Y Along Z At Intersection of Two Faces: This uses the same symbol as the Intersection relation. Coincident Collinear Concentric
135
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 136
SolidWorks Basics
Coradial Equal Equal Curvature Fix Horizontal Intersection: This uses the same symbol as At Intersection of Two Faces. Midpoint Offset On Edge On Surface: This is the same as the Coincident symbol. Parallel Perpendicular Pierce Symmetric Tangent Vertical Display/Delete Relations is described in detail in the Sketch toolbar section. Fully Define Sketch interface uses sketch relations and dimensions to fully define the active sketch. It allows you to select what types of sketch relations and dimensions will be used to do this. Figure 4.28 shows the Fully Define Sketch interface. Scan Equal scans a sketch for entities with either the same length or the same radius, and applies Equal relations.
136
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 137
Working with Sketches
FIGURE 4.28 The Fully Define Sketch interface
Exploring Sketch Settings In addition to sketch tools, another important aspect of controlling sketches is sketch settings. Sketch settings are found in two different locations. The first location is at Tools ➪ Options ➪ Sketch. In this chapter, we cover the settings found at the second location, Tools ➪ Sketch Settings. These settings mainly affect sketch relations.
CROSS-REF
The sketch settings at Tools ➪ Options ➪ Sketch are discussed in detail in Appendix B. They mainly affect sketch display issues, and have some overlap with Tools, Sketch Settings.
Automatic Relations is covered in depth in the Dimensions/Relations toolbar section. Automatic Solve is turned on by default. As you make changes to a sketch by adding relations or changing dimensions, SolidWorks automatically and immediately updates the sketch to reflect the changes. When the Automatic Solve setting is turned off, these changes are deferred until you exit the sketch or turn the Automatic Solve setting back on. The setting can be useful to prevent intermediate solutions (for example, when half of the changes are made) that may cause problems with the sketch, and when you are confident that the outcome will be correct. If you import a large drawing from the DXF or DWG formats, these drawings import as sketch entities into either a SolidWorks sketch or a drawing. SolidWorks may automatically turn off the Automatic Solve setting for performance (speed) reasons on files of this type. Enable Snapping is turned on by default. It enables the cursor to snap to the endpoints of existing sketch entities to help you make cleaner sketches. When you turn this setting off, Automatic Relations is also disabled (although the icon for the setting remains depressed, Automatic Relations are not created).
137
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 138
SolidWorks Basics
No Solve Move is discussed in the Sketch toolbar section. Detach Segment on Drag is turned off by default. When you turn this setting on, the Detach Segment on Drag feature enables you to pull a single sketch element away from a chain of elements. For example, if you have a rectangle and you want to detach one of the lines from the rest of the rectangle, without using this setting, you would have to draw extra geometry and then trim and delete lines in order to release the endpoints. It is recommended that you leave this setting off. Turn it on only when you need it, and then immediately turn it off again. This setting can be hazardous for everyday use, since it enables you to simply drag sketch elements that may be otherwise fully defined.
BEST PRACTICE
Override Dims on Drag is off by default. When you turn this setting on, it enables you to drag fully defined sketch geometry, and the dimensions will update to match the dragged size. This is another setting that you should use sparingly. It can be useful for doing concept work, but you should leave it off when working with production data for obvious reasons.
Using Sketch Blocks Sketch blocks are collections of sketch entities that can be treated as a single entity. You can use sketch blocks in parts, assemblies, and drawings. To create a sketch block, select a group of sketch entities and click the Make Block button on the Blocks toolbar, or select Tools ➪ Blocks ➪ Make. Blocks may be internal to a particular document, or they may be saved as an external file. The externally saved block may be linked to each document where it is used, so that if the block is changed, it updates in the documents where it is used. You can use blocks in conjunction with the Make Path function mentioned earlier in this chapter to create functional layouts for mechanisms. The following is a description of the various tools that are available on the Blocks toolbar. Make Block creates a sketch block from selected sketch entities. You can position a manipulator to denote the insertion point for the block. Blocks may attach at any entity endpoint, but the insertion point follows the cursor. Edit Block enables you to edit an existing block as if it were a regular sketch. Insert Block allows you to select from a list of open blocks or browse to a location where blocks are stored. You can edit the insertion point by using the Edit Block function.
138
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 139
Working with Sketches
Add/Remove, while editing a block, allows you to add or remove sketch entities from the block without deleting them from the sketch. Rebuild Block allows changes to a block to be reflected in any external relations without exiting the block. For example, if you have a block in a sketch, and a sketch line is coincident to one of the endpoints in the block, you may edit the block such that the referenced endpoint moves. As a result, the line in the sketch will not move until you either exit the block or use the Rebuild Block function. Save Block saves a selected block to an external file (with the *.sldblk extension). Explode Block removes all of the sketch entities from a block and brings them into the current sketch. Belt/Chain enables you to make a belt or chain around a set of pulleys. Each pulley must be a block. After activating the command, you can select each pulley and use the arrow on the pulley to switch the side of the pulley to which the belt goes. You can also compensate for the thickness of the belt (this is important when both sides of the belt are in contact with pulleys), and drive the pulley arrangement using the length of the belt. Figure 4.29 shows the Belt/Chain dialog box.
FIGURE 4.29 The Belt/Chain dialog box
139
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 140
SolidWorks Basics
Tutorial: Learning to Use Sketch Relations While it is useful to read through the definitions and functions of all of the sketch entities, tools, and relations, using your mouse to create is what this is all about. This tutorial makes sure that you get to know all of the major functions in SolidWorks sketches. Almost every part that you build will start with a sketch, so this is a skill worth mastering. Follow these steps to learn about sketch relations: 1. Open a new part using a template that you set up in the Template tutorial from Chapter 3. If you do not have this template, there is one provided for you on the CD-ROM named BibleInchTemplate.prtdot. Copy it to your templates folder and use it to create a new part. You may also use a SolidWorks default template. 2. Select the Front plane in the FeatureManager, and click the Sketch button on the Sketch toolbar. Click the Line tool from the Sketch toolbar. 3. Move the cursor near the Origin; the yellow Coincident symbol appears. 4. Draw a line horizontal from the Origin. Remember that there are two ways to sketch the line, Click-Click or Click-Drag. Make sure that the line snaps to the horizontal and that there is a yellow Horizontal relation symbol. The PropertyManager for the line should show that the line has a Horizontal relation. Also notice that the line is black, but the free endpoint is blue. This means that the line is fully defined except for its length. You can test this by dragging the blue endpoint. 5. Click the Smart Dimension tool on the Sketch toolbar, use it to click the line that you just drew, and place the dimension. If you are prompted for a dimension, type 1.000. If not, then double-click the dimension; the Modify dialog box will appear, enabling you to change the dimension. 6. Draw two more lines to create a right triangle to look like Figure 4.30. If the sketch relations symbols do not show in the display, turn them on by clicking View ➪ Sketch Relations. You may want to set up a hotkey for this, because having sketch relations is useful, but often gets in the way.
FIGURE 4.30 Draw a right triangle.
140
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 141
Working with Sketches
7. Drag the blue endpoint of the triangle. Dragging endpoints is the most direct way to change the geometry. Dragging the line directly may also work, but this sometimes produces odd results, particularly in versions earlier than SolidWorks 2007. The sketch leaves a ghost when dragging so that you can see where you started. 8. Click the Smart Dimension tool, and then click the horizontal line and the angled line. This produces an angle dimension. Place the angle dimension inside the triangle, and give it a value of 30°. 9. Click the Sketch Fillet tool, set the radius value to 0.10 inches, and click each of the three endpoints. Where the 1.000-inch dimension connects to the sketch, SolidWorks has created virtual sharps. Figure 4.31 shows the sketch at this point. You may now want to turn off the Sketch Relations display because the screen is getting pretty busy. You can find this setting at View ➪ Sketch Relations.
FIGURE 4.31 The resulting sketch after you perform step 9
10. Draw a line starting from the midpoint of the angled line. The midpoint should highlight when you move the cursor close to it. Draw the line perpendicular to the angled line. A dotted gray line appears, showing where the perpendicular lies. When you follow this line, the yellow perpendicular symbol appears on the cursor. Make this line approximately .75 inches long. Feedback on the cursor also shows the length of the line as you draw it. 11. Draw two more lines ending at the endpoint of the sketch fillet, as shown in Figure 4.32. Use the Inferencing lines to line up the second angled line with the end of the arc. The last line drawn is thin, and the second line drawn is blue. The thin line indicates that there is a potential problem with the sketch, but not an error in solving the relations. The problem is that an extrude requires a single closed loop, and this sketch is not a closed loop. 12. Click the Trim tool from the Sketch toolbar. Make sure that the Trim option is set to Closest. Click the angled line of the triangle between the thin line and the line at the midpoint. This trims out that section, and makes the sketch a closed loop, so that the thin line now has a regular thickness. A warning may appear because you have a Midpoint relation to the line being trimmed, and you no longer want this relation, but you want the lines to intersect at their endpoints. Select Yes at the prompt.
141
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 142
SolidWorks Basics
FIGURE 4.32 The resulting sketch after you perform step 11
13. Click the Smart Dimension tool. Use it to create aligned dimensions on the short line (.25 inches) and one of the long lines (.125 inches). You may now want to reorganize some of the dimensions if the display is becoming crowded. 14. At this point, two of the lines should be blue, but it may not be clear why they are not defined. Select one of the blue lines and drag it. Notice that what changes is the arc nearest the Origin. This changes in a way that is not useful for this part. To lock this line where it needs to be, select the blue line nearest the Origin and the centerpoint of the arc nearest the Origin, and give them a Coincident relation in the PropertyManager. The result is a fully defined sketch, as shown in Figure 4.33.
FIGURE 4.33 The resulting sketch after you perform step 14
15. Save the part with the name Sketch Relations Tutorial.sldprt. Close the part.
142
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 143
Working with Sketches
Tutorial: Using Blocks and Belts Sometimes I am amazed at the things that can be done in SolidWorks, even with fairly simple tools. This is one of those times. If you design machines, then this tutorial will have some extra meaning for you. If you do not design machines, then these are still valuable tools to have in your toolbox ready to use in various situations. Follow these steps to learn about using Blocks and Belts. 1. Open a new part with inches as the units. 2. Draw a sketch on the Front plane as shown in Figure 4.34, with four lines connected to the Origin. Exit the sketch and rename it as Layout Sketch, either by clicking twice on the name of the feature in the FeatureManager or by selecting it and pressing F2.
FIGURE 4.34 The layout sketch
3. Open a second sketch on the Front plane, and draw a circle centered on the Origin with a 6-inch diameter. 4. Inside the circle, draw a rectangle around the Origin. 5. Select two adjacent sides of the rectangle and make an Equal sketch relation between them (this makes the rectangle into a square). 6. Draw a diagonal construction line (using the Centerline tool) across the square from corner to corner. 7. Press Esc to exit the Centerline command. 8. Select the centerline, Ctrl-select the Origin, and apply a Midpoint relation to them. This is a very common technique for centering a rectangle on a point.
143
4
09_080139 ch04.qxp
Part I
3/26/07
3:31 PM
Page 144
SolidWorks Basics
ON the CD-ROM
The CD-ROM for Chapter 2 contains a macro that automatically draws a rectangle that is centered on the Origin.
9. Click the Smart Dimension tool, and apply a 1.000-inch dimension to one side of the square. Turn off the Smart Dimension tool by clicking it again on the toolbar or pressing Esc. 10. If the Blocks toolbar is not active, then activate it and select Make Block. You can also access this command through Tools ➪ Block ➪ Make. 11. Window select the circle and the square by clicking and dragging a box that includes all of the items in the sketch. The PropertyManager to the left displays a circle and five lines that are to be made into a block. 12. Expand the Insertion Point panel in the PropertyManager. This causes a blue manipulator Origin to appear in the graphics window. Click this Origin and drag it onto the center of the circle. Then click the green check mark icon to exit the Make Block dialog box. This is shown in Figure 4.35.
FIGURE 4.35 Creating a block
13. The items in the block now turn gray. Click anywhere on the block and drag it out of the way. Then drag the center of the circle and drop it on the part Origin. 14. Click the Insert Block tool on the Blocks toolbar. Place the block on the opposite sharp corner of the layout sketch. 15. Create another block that is identical to the first one, except that it has a diameter of three inches instead of six inches. You can do this by selecting the first block, clicking Edit Block from the toolbar, and copying (window select and Ctrl+C). Then exit the Edit Block and paste (Ctrl+V) in the regular sketch. Make sure to also change the insertion point for this second block to the center of the circle. 16. Insert a second instance of this second block, and make sure that both of them have the center of the circle at the two remaining intersection points of the four-sided shape of the layout sketch. At this point, your sketch should look like Figure 4.36.
144
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 145
Working with Sketches
FIGURE 4.36 Block placement
17. Click the Belt/Chain tool on the Blocks toolbar. Select the blocks in counter-clockwise order, starting at the Origin. On the last pulley, you will have to click the arrow to get the belt to go the correct way around the pulley. 18. Make sure that the Engage Belt option is selected. This allows you to make the pulleys move in the same way that they would in a real mechanism. 19. Click the Use Belt Thickness option, and assign .25 inches for the thickness. The belt should be offset from the pulleys. 20. Click the green check mark icon. 21. Click and drag one of the corners of the square in a pulley. All of the pulleys should turn as if this were a real mechanism. The ratios are also observed because the small pulleys rotate faster than the large ones. 22. Save this part as Blocks and Belts Tutorial.sldprt. Exit the part.
Summary Sketching in SolidWorks is something that you will do almost every time you open the software. There are a lot of automated features available that you can allow to do the work for you. You also have a lot of control to make changes manually. The options for creating intelligent relationships that establish your design intent, as well as SolidWorks’ capabilities in laying out mechanisms, is only limited by your imagination. The more familiar you become with the tools in your toolbox, the more of a craftsman you can become with this software.
145
4
09_080139 ch04.qxp
3/26/07
3:31 PM
Page 146
10_080139 ch05.qxp
3/26/07
3:32 PM
Page 147
Creating Simple Parts, Assemblies, and Drawings
W
hen you begin to build a model in SolidWorks, there are a few things to consider before you start. If you spend some time considering what you are doing first, then it will benefit you later in the process. Good modeling practice is based on robust design intent, which just means that you build a part that can adapt easily to changes. This section begins with questions that you need to ask.
Asking the Right Questions Asking the right questions is the first step to getting the right answers. By asking questions about the part now, you can create a model that will be easier to edit, easier to properly place into an assembly, easier to detail in drawings, and easier for other SolidWorks users to understand when someone else has to work on your models. The questions focus on the physical manufactured part. Sometimes you will be able to find answers for the questions, and other times not. Whether you are doing the modeling for someone else, or doing the design and modeling yourself may make a difference in how you approach the modeling task. The purpose of these questions is to help you establish design intent. The term design intent is difficult to define, but it is basically a statement of how the part functions and how the model reacts to modeling changes. It may help to try to put the design intent into words to help you focus on what is important in the design. An example of a statement of design intent might be: “This part is symmetric about two planes, is used to support a 1.00" diameter shaft with a constant downward load of 150 pounds using a bronze bushing, and is bolted to a plate below it.” This does not give you
147
IN THIS CHAPTER Asking the right questions Tutorial: Creating a simple part Tutorial: Creating a simple assembly Tutorial: Making a simple drawing
10_080139 ch05.qxp
Part I
3/26/07
3:32 PM
Page 148
SolidWorks Basics
enough information to design the part, but it does give you information about two surfaces that are important (a hole for the bushing and the bottom that touches the mounting plate), as well as some general size and load requirements. The following questions can help you to develop the design intent for your own projects.
Is the part symmetrical? Symmetry is an important aspect of design intent. Taking advantage of symmetry can significantly reduce the time needed to model the part. Symmetry can exist on several levels: n Sketch symmetry n Individual feature symmetry n Whole-part symmetry n Axial symmetry (a revolved part) n “Almost” symmetry (the whole part is symmetrical, except for a few features) n Left and right symmetrical versions of the part
What are the primary or functional features? This is probably the most important question. Primary or functional features include how the part mounts or connects to other parts, motion that it needs to accommodate, and additional structure to support loads. Often it is a good idea to create a special sketch as the first feature in the part that lays out the functional features. This could be as simple as a straight line to denote the bottom and a circle to represent the position and size of a mating part, or as complex as full outlines of parts and features from all three standard planes. This technique is called a layout sketch, and it is an important technique in both simple and complex parts. You can use layout sketches for anything from simply drawing a size-reference bounding box to creating the one point of reference for all sketched features in the part. You can use multiple layout sketches if a single sketch on one plane is not sufficient.
In what ways is the part likely to change? When the marketing department gets out of their meeting at 4:45 pm, what changes do you need to be prepared for so that you can still be out the door by 5:00 pm? No one expects you to be able to tell the future, but you do need to model in such a way that your model easily adapts to future changes. As you gain experience with the software, and you keep this idea in mind, then you will develop some instincts for the type of modeling that you do.
148
10_080139 ch05.qxp
3/26/07
3:32 PM
Page 149
Creating Simple Parts, Assemblies, and Drawings
What is the manufacturing method? Modeling for the casting process is very different from modeling for the machining process. The process should be evident in your modeling. There are times when you will not know which process will be used to create the part when you start to create a model. If you are simply making an initial concept model, then you may not need to be concerned about the process. In these cases, it may or may not be possible to reuse your initial data if you need to make a detailed cast part from your non-process-specific model. Decisions like this are usually based on available time, how many changes need to be made, and a determination of the risk of making the changes versus not making the changes, as well as which decision will cost you the most time in the long run. As engineers, we are typically perfectionists. However, there always needs to be a balance between perfection and economy. Achieving both simultaneously is truly a rare event. Still, you should be aware that problems left by the designer for other downstream applications to solve (such as machinists, mold makers, and assemblers) also have an impact on the time and cost of the project.
BEST PRACTICE
The best practice in this case is a judgment call. When faced with assembling a model sloppily or remodeling it perfectly, I usually choose to remodel because doing it the second time is always faster. Also, if additional changes are required, then you do not need to struggle with the sloppily assembled model. You can easily copy sketches from one part to another, while keeping the old part open as you build the new part. As a result, you may be surprised how quickly things go.
Will there be secondary operations? When working with any manufacturing process, some secondary processes are generally required. For example, if you have a cast part, then you may need to machine the rough surface to create a flat face in some areas. You may also need to ream or tap holes. In plastic parts, you may need to press in threaded inserts. There are some special tools in SolidWorks that you can use to document secondary operations: n A technique called Configurations in SolidWorks allows you to create different versions of a part. For example, one configuration may have the features for the secondary operations suppressed (turned off), and showing just the part as cast, while the other configuration shows the part as machined.
CROSS-REF
Chapter 10 discusses configurations and feature suppression in depth.
n A technique called Insert Part allows you to use one SolidWorks part as the starting point for a second part. For example, the as-cast part has all of the features to make the part, but it is inserted as the first feature in the as-machined part, which adds the cuts required by the machining process.
149
5
10_080139 ch05.qxp
Part I
3/26/07
3:32 PM
Page 150
SolidWorks Basics
Will there be other versions? Sometimes there are size-based versions of parts that have to be created, or versions based on additional features. If these are fairly simple, they can also be handled with configurations, but you need to plan this flexibility in advance.
Creating a Simple Part In this section, we build the simple part shown in Figure 5.1. While the shape is simple, the techniques used and discussed here are applicable to a wide variety of real-world parts.
FIGURE 5.1 A simple machined part
Where to start? When you start a new part from a template and are confronted with the blank screen with only the part Origin showing, this is the question that first comes to mind. Of course, it depends on the shape and function of your part, but for the time being, you can assume that you are working with the rectangular part shown in Figure 5.1. The first feature that you create should somehow be positioned relative to the Origin. Whether there is a corner of a rectangle that is coincident to the Origin, the rectangle is centered on the Origin, or dimensions are used to stand the rectangle off from the Origin at some distance, you need to lock the first feature in two-dimensional space to the Origin.
150
10_080139 ch05.qxp
3/26/07
3:32 PM
Page 151
Creating Simple Parts, Assemblies, and Drawings
When working with a simple part, the entire part can be described as rectangular or cylindrical. In these cases, it is easy to know where to start: you simply draw a rectangle or a circle, respectively. On complex parts, it may not be obvious where to start, and the overall part cannot be said to have any simple shape. In cases like this, it may be best to select the (or a) prominent feature, mounting location, functional shape, or focus of the mechanism. For example, if you were to design an automobile, what would you designate as the 0,0,0 Origin? The ground may be a reasonable location, or the plane of the centers of the wheels. Much of the automotive industry uses the center of the end of the crankshaft in the engine as the assembly Origin. That may seem arbitrary, but as long as everyone working on the vehicle agrees, it is as good a location as any. With that in mind, it seems logical to start the part shown in Figure 5.1 by sketching a rectangle. Select the Top plane, and sketch a rectangle centered on the part Origin.
Symmetry The next decision is about part symmetry. This part is not completely symmetrical, and so modeling a quarter of it and mirroring the entire model twice is not going to be the most effective technique. Instead, you should build the part symmetrically around the Origin, and mirror individual features as appropriate. To start with this type of symmetry, you need to sketch a rectangle centered around the Origin. The centered rectangle is something that you will create frequently enough to warrant using a macro.
ON the CD-ROM
A macro that creates a rectangle centered on the Origin is provided on the CD-ROM in the materials for Chapter 2.
Figure 5.2 shows two common techniques for centering a rectangle on the Origin. You can use the sketch relation symbols to identify the relations that have been applied to this sketch.
FIGURE 5.2 Centering a rectangle on the Origin
151
5
10_080139 ch05.qxp
Part I
3/26/07
3:32 PM
Page 152
SolidWorks Basics
TIP
To make a rectangle work like a square, use an Equal sketch relation on two adjacent sides. This only requires a single dimension to drive the size of the square.
Beginning with the rectangle that you sketched in the previous section, apply one horizontal dimension (4.00 inches) and one vertical dimension (6.00 inches). The sketch is fully defined at this point because both the size and position of the rectangle have been established. If you are dimensioning a horizontal line, the best way to do it is to simply select the line and place the dimension. Selecting the line endpoints can also work, but selecting the vertical lines on either side of the horizontal lines is not as robust. The problem is that if you use this third method, deleting either of the vertical lines causes the dimension to also be deleted. In the first two dimensioning methods, dimensions are not deleted unless you remove one of the endpoints, which requires deleting two lines, the horizontal line, and one of the vertical lines.
BEST PRACTICE
Make it solid Next, click Extrude from the Features toolbar, or click Insert ➪ Features ➪ Extruded. In the Direction 1 panel, select Mid Plane as the end condition. SolidWorks takes the distance that you entered and extrudes it symmetrically about the sketch plane. Enter 1.00 inch as the distance. By centering the sketch on the Origin and extruding by using a Mid Plane end condition, the initial block is built symmetrically about all three standard planes, with the part Origin at the center. In many parts, this is a desirable situation. It enables you to create mirrored features using the standard planes, and also helps you to assemble parts together in an assembly later, when parts must be centered and do not have a hard face-to-face connection with other parts. Figure 5.3 shows the initial feature with the standard planes.
FIGURE 5.3 An initial extruded feature centered on the standard planes
152
10_080139 ch05.qxp
3/26/07
3:32 PM
Page 153
Creating Simple Parts, Assemblies, and Drawings
Extrude Feature Options
T
he Extrude feature is one of the staples of SolidWorks modeling. Depending on the type of modeling that you do, the Extrude feature may be one of your main tools.
The Extrude interface
From The From panel establishes where the Extrude feature starts. By default, SolidWorks extrudes from the sketch plane. Other available options are:
n Surface/Face/Plane: The extrude begins from a surface body, a face of a solid, or a reference plane.
Extruding from a surface continued
153
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 154
SolidWorks Basics
continued
CROSS-REF
Surface features are discussed in detail in Chapter 27.
n Vertex: The distance from the sketch plane to the selected vertex is treated as an offset distance.
n Offset: You can enter an explicit offset distance, and you can also change the direction of the offset.
Direction 1 and Direction 2 Direction 1 and Direction 2 are always separated by 180 degrees. Direction 2 becomes inactive if you select Mid Plane for the end condition of Direction 1. The arrows that display in the graphics window show a single arrow for Direction 1 and a double arrow for Direction 2. For the Blind end condition, which is described below, dragging the arrows determines the distance of the extrude. Each of the end conditions is affected by the Reverse Direction toggle. This toggle simply changes the default direction by 180 degrees. You need to be careful when using this feature, particularly when using the Up to end conditions, because if the entity that you are extruding up to is not in the selected direction, then an error results. Following is a brief description of each of the available end conditions for the Extrude feature:
n Blind: Blind in this case means an explicit distance. The term is usually used in conjunction with holes of a specific depth, although here it is associated with a boss rather than a hole.
n Up to Vertex: In effect, Up to Vertex works just like the Blind end condition, except that the distance is parametrically controlled by a model vertex or sketch point.
n Up to Surface: Up to Surface could probably be better named Up to Face, because the end does not necessarily have to be an actual surface feature. This end condition may display a warning if the projection of the sketch onto the selected face extends beyond the boundary of the face. In that case, it is advisable to knit several faces together into a surface body and to use the Up to Body end condition.
n Offset from Surface: By default, Offset from Surface extrudes until it reaches a specified distance from a selected surface. There are two methods for determining the type of offset and one to determine direction.
n The default offset method behaves as if the selected surface were offset radially, so that a surface with a 4-inch radius and a 1-inch offset would give a curvature on the end of the extrude of a 3-inch radius.
n The second method, called Translate Surface, behaves as if the surface were moved by the offset distance.
154
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 155
Creating Simple Parts, Assemblies, and Drawings
Offset from surface using the default and Translate Surface options
n Reverse Offset refers to when the offset stops short of the selected face or when it goes past it. These options are illustrated in the following figure.
The Reverse Offset option continued
155
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 156
SolidWorks Basics
continued
n Up to Body: The Up to Body end condition is very useful in many situations, especially when receiving the error message, “The end face cannot terminate the extrusion,” from the Up to Face end condition.
n Mid Plane: The Mid Plane end condition eliminates the Direction 2 options and divides the extrude distance equally in both directions, so that if you specify a 1.00-inch Mid Plane, then SolidWorks extrudes .50 inches in one direction and .50 inches in the other direction.
n Through All: The Through All end condition is available only when there is already solid geometry existing in the part. When used for an extruded boss (which adds material), it extrudes to the distance of the farthest point of the solid model in a direction perpendicular to the sketch plane. When used for a cut, it simply cuts through everything.
n Up to Next: Up to Next extrudes the feature until it runs into a solid face that completely intercepts the entire sketch profile. If a portion of the sketch hangs over the edge of the face, the extrude feature will keep going until it runs into a condition that matches that description, which may be the outer face of the part in the direction of the extrusion.
The Up to Next end condition used with a Cut extrude By default, the Direction of Extrusion is normal to the sketch plane, but you can also select a linear entity such as an edge or axis as the direction. All of the end-condition options are still available when you manually define the Direction of Extrusion as something other than the default. You can also assign a Draft option to an extrusion as it is created, and you can control the draft separately for Direction 1 and Direction 2. When dealing with molded or cast parts, certain types of features, such as drafts, fillets, and shells, are often the targets of users trying to assign best practices. This is partially because using drafts, fillets, and shells is very much like playing Rock, Paper, Scissors; you can never really win this game except by luck. Arranging the features in the correct order so that the model is efficient and achieves the desired results is challenging and resistant to rules that apply in most situations. It is usually best to apply draft as a separate feature rather than using it in the definition of the Extrude feature. It is also best to apply draft after most of the modeling is done, but before you apply the cosmetic fillets, and before using the shell feature.
BEST PRACTICE
156
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 157
Creating Simple Parts, Assemblies, and Drawings
Thin Feature The Thin Feature panel is activated by default when you try to extrude an open loop sketch (a sketch that does not fully enclose an area). The end-condition options remain the same, but what changes is that the feature applies a thickness to the sketch elements, in the manner of a sheet metal, thinwalled plastic part, or a rib. The Thin Feature panel of the Extrude PropertyManager, along with a representative thin feature extrusion, is shown in the following figure. The Cap Ends option is available only when you specify a Thin Feature to be created from a closed loop sketch. This creates a hollow, solid body in a single step. You can also use Thin Features with cuts, and they are very useful for creating slots or grooves.
The Thin Feature panel, and a thin feature extrusion
Contour Selection SolidWorks works best when the sketches are neat and clean, when nothing overlaps, and there are no extra entities on closed loops. However, when you need to use a sketch that does not meet these parameters, you can use an alternative method called Contour Selection. Contour Selection enables you to select enclosed areas to be used for features, regardless of how many normal sketch rules the rest of the sketch violates. It is my opinion that this feature was introduced into SolidWorks only to keep up with other CAD packages, not because it is a great feature. I do not recommend using Contour Selection on production parts. It is useful for creating quick models, but the selection is too unstable for any data that you may want to rely on in the future. The main problem is that if the sketch changes, the selected area may also change, or SolidWorks may lose track of it entirely.
BEST PRACTICE
157
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 158
SolidWorks Basics
Making the groove The next modeling step is to create a groove on the back of the part. How is this feature going to be made? You can use several techniques to create this geometry. List as many techniques as you can think of, whether or not you know how to use them. Later, we will sort through which techniques work and which do not. One of the secrets to success with SolidWorks, or indeed any tool-based process, is to know several ways to accomplish any given task. By working through this exercise, you gain problem-solving skills as well as the ability to improvise when the textbook method fails.
TIP
FIGURE 5.4 Methods for creating the groove
In Figure 5.4, the first image shows a nested loop sketch, with one closed loop inside another. This technique cuts away the material between the loops. The second image shows a swept cut, with a path for the cut and a cross-section. The third image shows a Thin Feature cut, with only the centerline of the groove used as a sketch. Another option could include a large pocket being cut out, with a boss adding material back in the middle.
Relative size or direct dimensions? Of these methods, the Thin Feature cut is the simplest and most direct because the sketch is easiest to create and control. The sketch for this feature is simply a rectangle. In this case, it makes sense to use sketch fillets to round the corners rather than fillet features. There are a few ways to create the rectangle, and the method that you choose depends on the design intent. For example, although the rectangle needs to remain centered and symmetrical, you also have to consider which
158
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 159
Creating Simple Parts, Assemblies, and Drawings
is the more important aspect: the size of the groove or the overall size of the part? If the size of the part is more important than the size of the groove, then it might be best to create the groove as an offset of the outer shape of the block, rather than driving its dimensions independently. To summarize, the groove dimensions are driven by the overall shape of the block. To create a groove, you can create a rectangle by offsetting the block shape, and use sketch fillets to round the corners.
Creating the offset There is one more thing to consider before you create the sketch. What should you use to create the offset: the actual block edges or the original sketch? The answer to this is a Best Practice type issue. When creating relations that need to adapt to the biggest range of changes to the model, it is best to go as far back in the model history as you can to pick up those relations. In most cases, this means creating relations to sketches rather than to edges of the model. Model edges can be fickle, with the use of fillets, chamfers, and drafts.
BEST PRACTICE
This best practice tip will become more significant the first time you create a feature built from model edges, and then make changes that break relations.
To create the offset for your part, follow these steps: 1. Open a sketch on the face of the part. To create the offset, expand the Extrude feature by clicking the plus icon next to it in the FeatureManager so that you can see the sketch. Regardless of how it displays here, this sketch appears before the extrude in the part history. RMB click the sketch and select Show. You can view individual sketches and reference geometry entities such as planes from the RMB menu. However, the global settings for the visibility of these items are found in the View menu. You can access these items faster by using the View toolbar, or by linking the commands to hotkeys.
TIP
2. Next, RMB click the sketch in the graphics window and click Select Chain. This selects any non-construction, end-to-end sketch entities. Click Offset Entities on the Sketch toolbar. Offset to the inside by .400 inches. Apply .500-inch sketch fillets to each of the corners. 3. Click Extruded Cut on the Feature toolbar. By default, the extruded cut will cut away everything inside the closed profile of the sketch. Look down the FeatureManager window and click the check box on the top bar of the Thin Feature panel. Make the cut Blind, .100 inch. The Thin Feature type should be set to Mid Plane with a width of .400 inches. The PropertyManager and graphics window should look like Figure 5.5.
159
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 160
SolidWorks Basics
FIGURE 5.5 Using the Groove feature
Sketch techniques Although the next two features could be more easily and efficiently created by using a cut, I will create them as two extrudes. The main point here is to show some useful sketch techniques, rather than optimum efficiency. Begin with the part from the previous section and follow these steps: 1. Open a new sketch on the large face opposite from the groove. Draw a rectangle picking up the automatic coincident relation to one corner and then dragging across the part and picking up another coincident to the edge on the opposite side. Figure 5.6 shows the rectangle before and after this edit. If you want to continue using the recommended best practice mentioned earlier of making relations to sketches rather than model edges, here are a few tips. In some situations (such as the current one) the sketch plane is offset from the sketch that you want to make relations to, and so the best bet is to use the Normal To view. The next obstacle is making sure that automatic relations pick up the sketch rather than the edge, and so you can use the Selection Filter to only select sketch entities.
TIP
2. Delete the Horizontal relation on the line that is not lined up with an edge. This enables you to drag it to an angle or apply the dimensions shown.
You can delete the Horizontal relation by selecting the icon on the screen. As a reminder, you can show and hide the sketch relation icons from the View menu. You can check to ensure that the relations were created to the sketch rather than the model edges by clicking the Display/Delete Relations button on the Sketch toolbar, clicking the relation icon to check, and expanding the Entities panel in the PropertyManager. The Entities box shows
160
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 161
Creating Simple Parts, Assemblies, and Drawings
where the relation is attached to, as shown in Figure 5.7. In this case, it is a point in Sketch1. Without custom programming, there is no way to identify items in a sketch by name, but you already know which point it is; you just needed to know whether it was in the sketch or on the model.
FIGURE 5.6 Edits to a rectangle
Automatic coincident relation
Automatic coincident relation
Delete horizontal relation
FIGURE 5.7 The Display/Delete Relations dialog box
161
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 162
SolidWorks Basics
3. The second sketch trick involves the use of a setting. Before you try this, go to Tools ➪ Options ➪ Sketch, and ensure that Prompt To Close Sketch is turned on; then click OK to close the dialog box. 4. Open another new sketch on the same face that was used by the last extrusion. Draw an angled line across the left and bottom sides of the box, with the dimensions shown in Figure 5.8. In this case, in order for this technique to work, the endpoints of the line have to be coincident with the model edges rather than the sketch entities.
This line by itself constitutes an open sketch profile, meaning that it does not enclose an area, and has unshared endpoints. Ordinarily, this results in a Thin Feature, as described earlier, but when the endpoints are coincident with model edges that form a closed loop, and the setting mentioned previously is turned on, SolidWorks automatically gives you the option of using the model edges to close the sketch. This saves several steps when compared to selecting, converting, and trimming manually.
FIGURE 5.8 Using the prompt to close a sketch setting
5. Click the Extrude tool on the Features toolbar. Answer Yes to the prompt, and doubleclick the face of the previous extrusion. SolidWorks automatically uses the face that you double-clicked for an Up to Surface end condition. This is a simple way of linking the depths of the two extrusions automatically. Again, this entire operation could have been handled more quickly and efficiently with a cut, but these demonstrate an alternative method which in some situations may be useful.
162
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 163
Creating Simple Parts, Assemblies, and Drawings
Hole Wizard The next features that you will apply are a pair of counterbored holes. SolidWorks has a special tool that you can use to create common hole types, called the Hole Wizard. The Hole Wizard is a tool that helps you to create standard hole types using standard or custom sizes. You can place holes on any face of a 3D model or constrain them to a single 2D plane or face. A single feature created by the Hole Wizard may create a single or multiple holes, and a feature that is not constrained to a single plane can create individual holes originating from multiple faces, non-parallel, and even non-planar faces (holes may go in different directions). All holes in a single feature that you create by using the Hole Wizard must be the same type and size. If you want multiple sizes or types, then you must create multiple features.
Hole Wizard: Using 2D versus 3D Sketches Hole Wizard holes use either a 2D or a 3D sketch for the placement of the hole centers. You can define the centers by simply placing and dimensioning sketch points. The 3D sketch type is used by default, with the 2D sketch type only being used when you select a planar face prior to clicking the Hole Wizard tool. Because the 3D placement of holes seems so much more flexible, why would anyone want to use the 2D placement method? 3D sketches have several limitations with respect to dimensioning and sketch relations. Recent releases of SolidWorks have added relations such as Midpoint and Equal to 3D sketches, which are an improvement over previous versions, but still do not make the 3D sketch as usable as a 2D sketch in the end. Three-dimensional sketches are discussed in Chapters 17 and 31. Chapter 17 also gives a more detailed description of the Hole Wizard. Chapter 22 has additional information on the display of threads.
CROSS-REF
The following image shows a part with various types of holes created by the Hole Wizard, including counterbored, countersunk, drilled, tapped, and pipe-tapped holes. The part is shown in section view for clarity. The drilled hole is not shown in the figure. Countersunk
Tapped
Counterbored
Pipe tap
Holes created by the Hole Wizard
163
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 164
SolidWorks Basics
To apply counterbored holes to your part, follow these steps: 1. Select the face that the groove feature was created on, and click the Hole Wizard tool on the Features toolbar. Then set the hole to Counterbored, set the type to Socket Head Cap Screw, the size to one-quarter, and the end condition to Through All, as shown in Figure 5.9.
FIGURE 5.9 The Hole Wizard Hole Specification interface
2. Next, click to select the Positions tab at the top of the PropertyManager. This is where you place the centerpoints of the holes using sketch points. It is often useful to create construction geometry to help line up and place the sketch points. When you select a face to create a 2D Hole Wizard hole, SolidWorks always creates a sketch point at the location where you selected the planar face, and then activates the Point sketch tool. If you click anywhere in the graphics window with the Point tool active, you place additional points, which are used to create additional holes. If those points are off of the solid model, then they may cause errors. To exit the Point tool, just press Esc.
CAUTION
164
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 165
Creating Simple Parts, Assemblies, and Drawings
3. Draw two construction lines, horizontally across the part, with Coincident relations to each side. Select both lines and give them an Equal relation. The point of this step is to evenly space holes across the part without dimensions or equations. Although several methods exist to make multiple selections, a box or window selection technique may be useful in this situation. If the box is dragged from left to right, then only the items completely within the box are selected. If the box is dragged from right to left, then any item that is at least partially in the box is selected.
TIP
SolidWorks displays an error if you try to place a sketch point where there is an existing sketch entity endpoint. If you build construction geometry in a sketch and want to place a sketch point at the end of a sketch entity, then you have to create the sketch point to the side where it does not pick up other incompatible automatic sketch relations, and then drag it onto the endpoint.
TIP
4. Place sketch points at the midpoint of each of the construction lines. If there is another sketch point other than the two that you want to make into actual holes, then delete the extra points. Dimension one of the lines down from the top of the part, as shown in Figure 5.10. All of the sketch relation icons display for reference. Click OK to accept the feature once you are happy with all of the settings, locations, relations, and dimensions.
FIGURE 5.10 Placing the centerpoints of holes
165
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 166
SolidWorks Basics
Cutting a slot The Hole Wizard does not specifically allow you to cut slots, nor is there a Slot feature. However, you can use one of the following methods to cut a slot: n Explicitly drawing the slot: Draw a line, press A to switch to the Tangent Arc tool, draw the tangent arc, press A to switch back to the Line tool, and so on. Although you can press the A key to toggle between the line and arc functions, you can also toggle between a line and a tangent arc by returning the cursor to the line/arc first point. n Rectangle and arcs: Draw a rectangle, place a tangent arc on both ends, and then turn the ends of the rectangle into construction entities. n Thin Feature cut: As you did earlier with the groove, you can also create a Thin Feature slot, although you need to follow additional steps to create rounded ends on it. n Offset in Sketch: By drawing a line, and using the Offset with Bi-directional, Make Base Construction, and Cap Ends settings, it is easy to create a slot from any shape by drawing only the centerline of the slot. n Library feature: A library feature can be stored and can contain either simple sketches or more complex sets of combined features. The library feature is a good option for the counterbored slot used in this example. Library features are discussed in depth in Chapter 19. To cut slots in your part, follow these steps: 1. In this case, use the Offset in Sketch option. Draw a line that represents the centerline of the slot, and use the sketch offset to create the rest of the sketch. Draw the line such that it is symmetrical about the Origin, using a construction line that is coincident to the Origin on one end and that has a Midpoint relation to the line to be offset on the other end. 2. Use an offset distance of .219 inches — as shown in Figure 5.11 — which is half of the counterbore diameter that is used in the Hole Wizard holes. From this sketch, create an extruded cut that extrudes up to the surface of the counterbore in the holes. 3. The through hole for the counterbored slot is also a slot, and so you can use the same technique. Open a sketch on the bottom of the previous slot, and draw a line that picks up automatic relations to the centers of the two rounded ends for the slot.
When you have drawn this line, use the Sketch Offset as before, and apply the Through All end condition to the cut. Picking up these relations automatically may seem difficult at first, but with some practice, it becomes automatic. When trying to find the center of an arc, the centerpoint is usually displayed and is easy to select. However, when making a relation to an edge, the centerpoint does not display by default. To display it, hold the cursor over the arc edge for a few seconds; a marker that resembles a plus sign inside a circle will show you where the center is, thus allowing you to select it with a sketch tool and pick up the automatic relations.
TIP
166
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 167
Creating Simple Parts, Assemblies, and Drawings
FIGURE 5.11 Creating a slot
In Figure 5.12, the first centerpoint has already been referenced, and the cursor is trying to find the centerpoint of the other end of the slot.
FIGURE 5.12 Applying automatic relations to a circular edge
Fillets and chamfers Several chapters could be written just about fillet types, techniques, and strategies in SolidWorks. Chapter 7 deals with more complex fillet types. As mentioned earlier, it is considered a best practice to avoid sketch fillets when possible, using feature fillets instead. Another best practice guideline is to put fillets at the bottom of the design tree, or at least after all of the functional features. You should not dimension sketches to model edges created by fillets unless there are no better methods available. There are too many ways, and reasons, to change sketches to make other features, especially important features, dependent on them.
167
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 168
SolidWorks Basics
Do not dimension sketches to model edges that are created by fillets. While the previous best practice about relations to sketch entities instead of model edges was a mild warning, you must heed this one more carefully.
BEST PRACTICE
To add fillets and chamfers to your part, follow these steps: 1. Initiate a Fillet feature, and select the four short edges on the part. Set the radius value to .600 inches. Click OK to accept the Fillet feature. When selecting edges around a four-sided part, the first three edges are usually visible and the fourth edge is not. You can select invisible edges by expanding the Fillet Options panel of the Fillet PropertyManager, and selecting the Select Through Faces option. When you have a complex part with a lot of hidden edges, this setting can be bothersome, but in simple cases like this, it is useful. Figure 5.13 shows this option in action.
TIP
FIGURE 5.13 Selecting an edge through model faces
2. Apply chamfers to the edges of the angled slot through the part, as indicated in Figure 5.14. Make the chamfers .050 inches by 45 degrees.
Chamfers observe many of the same best practices as fillets. Feature order is important with features like chamfers and fillets because of how they both tend to propagate around tangent edges. Although you can turn this setting off for both types of feature, it is best to get the correct geometry by applying the features in order.
TIP 168
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 169
Creating Simple Parts, Assemblies, and Drawings
CROSS-REF
The Fillet Xpert, which helps you to manage large numbers of overlapping fillets by automatically sorting through feature order issues, is discussed in detail in Chapter 27.
3. Select the four edges that are indicated for fillets in Figure 5.14. Apply .050-inch-radius fillets. 4. Apply a last set of .050-inch chamfers to the back side of the counterbores and slot.
FIGURE 5.14 Edges for Fillet and Chamfer features
Chamfer edges
Fillet edges
Select to chamfer
The finished part is simple, but you have learned many useful techniques along the way. In the rest of this chapter, you will put the part together with other parts to form an assembly, and then create a quick 2D drawing of the part and the assembly to document the design.
Tutorial: Creating a Simple Assembly Up to this point, you have been learning about how to create geometry, or parts. Assemblies involve organizing that geometrical data to represent real products or parts of products. Assemblies can be complex or simple. They can be structured in a single level or use many subassemblies. Assemblies can be static or allow Dynamic Assembly Motion. Relationships in the assembly can also drive part geometry. This part of this chapter serves as an introduction to some of the basic functions and main features of assemblies. Because all of the geometry creation is done in the part document, most of what goes on in the assembly document has to do with organizing that geometry in space.
169
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 170
SolidWorks Basics
CROSS-REF
Chapters 12 to 16 discuss various aspects of assemblies in greater detail.
The following pages describe common techniques that are used in assemblies. The part created earlier in this chapter is assembled with some additional parts that have already been created. The main point here is to give you a basic understanding of the assembly functions that exist and how they work, before exploring various aspects of the software in greater detail in Part II. To create a simple assembly, follow these steps:
ON the CD-ROM
This tutorial uses parts called Chapter5Frame.sldprt and Chapter5Screw.sldprt from the CD-ROM, in the material for Chapter 5.
1. From the CD-ROM, open the part named Chapter5Frame.sldprt. With the part open, click the Make Assembly From Part button on the Standard toolbar. If you have not made a custom template for assemblies, use the default assembly template that installed with SolidWorks. Move the cursor to the assembly Origin, where the cursor changes to indicate that the part Origin will be lined up with the assembly Origin. If the Origin is not visible on the screen, use the View, Origins menu selection to turn it on.
The first part that you insert into an assembly has a Fixed constraint applied to it. This constraint is indicated by the (f) in front of the name of the part in the FeatureManager. Figure 5.15 shows the placement preview and cursor from step 1, as well as the FeatureManager after the part has been added.
FIGURE 5.15 Placing a part in a new assembly
The Frame part is a weldment. Weldments are discussed in detail in Chapters 31, 32, and 33. They are made of multiple bodies within a single part file. Multiple bodies are discussed in detail in Chapter 26.
CROSS-REF
170
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 171
Creating Simple Parts, Assemblies, and Drawings
2. Open the part that you created in the previous tutorial. If you do not have it, then you can open a pre-built copy from the CD-ROM materials for Chapter 5. Once you open the part, change to the assembly window. You can press Ctrl+Tab to change between open documents, and Alt+Tab to change between open applications. These are Windows conventions that are not exclusive to
TIP SolidWorks.
3. From the assembly menus, click Insert ➪ Component ➪ Existing Part/Assembly. This displays the PropertyManager, as shown in Figure 5.16. Select the machined part from the selection box and click in an open space in the graphics window to place it.
Newly placed parts in the assembly (except for the very first part) are completely undefined in terms of position or location. Instead of the (f) symbol, for Fixed, the newly placed part displays a (-) symbol, which means Underdefined. You can change a Fixed part to underdefined by selecting Float in the RMB menu. Figure 5.16 also shows the FeatureManager with the new part in it. It is a little confusing that (f) stands for Fixed when the opposite condition, Float, also starts with an f.
FIGURE 5.16 The Insert Component interface
NOTE
Parts in an assembly are positioned relative to one another with mates. Mates are in many ways similar to sketch relations.
4. Click the Mate button from the Assembly toolbar. The mate options that are not grayed out are available with the current selection. For example, in Figure 5.17, the corresponding faces of the weldment and the machined part are selected, and these faces can be mated coincident, parallel, perpendicular, at a distance, or at an angle.
171
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 172
SolidWorks Basics
FIGURE 5.17 Mate options
You can move a part in an assembly by clicking the part and dragging it with the LMB (left mouse button). It follows whatever mates you have applied to it. To rotate a part that does not have any mates applied to it, drag the part with the RMB. The MMB still rotates the view.
TIP
5. Select the Coincident mate, and then the faces as shown in the figure. If the machined part is turned as it is in Figure 5.17 (so that it interferes with the welded frame if the selected surfaces touch), then click the Flip Mate Alignment button on the popup toolbar or toggle the Mate Alignment buttons in the PropertyManager. Close the popup toolbar by clicking the green check mark icon. In contrast to sketch relations, most assembly mates have alignment orientation. Flat faces can be coincident in one of two orientations separated by 180 degrees. The same is true of concentric relations, as well as others. SolidWorks orients a part to the closest orientation that works. This means that it is often best to pre-position a part so that it picks up the correct mate orientation. This usually involves some combination of rotating the view and rotating the part.
BEST PRACTICE
6. Select the top angled face of the angled frame member and the corresponding flat face of the machined part. Make these faces coincident. In this case, the parts are already in the correct orientation, and so there is no need to pre-position them. Click the green check mark icon to accept the mate. 7. One more mate is required to fully define the position of the machined part. Drag the part and verify that it slides up and down the angled weldment member. Find the two tapped holes in the weldment and slide the machined part so that the holes appear in the counterbored slot. Ideally the holes should be symmetrical with the part, but the slot was created to allow room for adjustment.
172
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 173
Creating Simple Parts, Assemblies, and Drawings
8. Expand the machined part in the FeatureManager and select its Front plane. From the View menu, turn on the display of temporary axes, and Ctrl-select the temporary axes in the centers of the threaded holes in the frame, as shown in Figure 5.18. Select the Symmetric mate on the Advanced Mates panel. Turn off the display of temporary axes when the mate is complete.
FIGURE 5.18 Creating a Symmetric mate
Temporary axes
9. Through the menus or Assembly toolbar, click Insert Component, and use the Browse button to find the existing Chapter5Screw.sldprt part on the CD-ROM, or on your hard drive if you have copied it there. 10. Notice that this part behaves differently in certain situations. For example, when the cursor is over empty space, it is attached to the centroid of the part, but when the cursor is over a flat or cylindrical face, the part snaps to that face. This is because the part uses a Mate Reference, enabling planar and cylindrical faces to automatically get Coincident and/or Concentric mates when the part is dropped on them. 11. Make sure that the Pushpin feature is activated in the Insert Component PropertyManager, and then drop the part at the bottom of each counterbored hole. The part will automatically get Concentric and Coincident mates. Figure 5.19 illustrates the location where you should drop the part. Click OK to accept the part placement.
173
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 174
SolidWorks Basics
FIGURE 5.19 Using a Mate Reference
12. You need to place two more screws in the assembly, but these ones cannot be automatically mated; you need to do this manually. Copy two instances of the screws. To copy a screw, Ctrl-drag the part either from the graphics window or from the FeatureManager and drop it into the graphics window. 13. Position the part and the view so that you can see the cylindrical body of the screw and the cylindrical face of the threaded hole in the C-channel. With the Mate function active, select both faces and click OK. Click the other pair of mating faces and click OK again. 14. Now click the underside of the screw head and the counterbored surface of the slot, make sure that they will be coincident, and click OK. 15. Save and close the assembly.
This is a quick overview of the basic assemblies’ functionality, which is expanded on in later chapters.
Tutorial: Making a Simple Drawing If you are coming to SolidWorks from a dedicated 2D software, you will be creating drawings very differently from what you may be used to. In 2D design software, you draw each view individually, and when a change occurs, you have to go back through the views and ensure that each view is updated appropriately. In 2D, views are sometimes created sparingly because they are difficult to create and to update. This includes view types such as Isometric views, complex sections, and views projected at non-orthogonal angles.
174
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 175
Creating Simple Parts, Assemblies, and Drawings
In SolidWorks, drawing views are almost free, being simply projected from the 3D model. Updates are made in the model, and all views update automatically from there. You can handle dimensions in a couple of ways, either using the dimensions that you used to create the model, or placing new dimensions on the drawing (best practice for modeling is not necessarily the same as best practice for manufacturing drawings). To make a simple drawing, follow these steps: 1. Press the New button from the Standard toolbar, or click File ➪ New. From the New SolidWorks Document window, select the Drawing template. The template contains all of the document-specific settings. 2. After selecting the drawing template, the Sheet Format/Size dialog box displays, as shown in Figure 5.20. Select the D-Landscape sheet size, as well as the format that automatically associates with that sheet size, and click OK. If the Model View PropertyManager appears, click the red X icon to exit.
FIGURE 5.20 The Sheet Format/Size dialog box
Paper size Use this for custom size paper
Border and associated text
Turn this off if you want a blank drawing sheet
3. Before creating any views on the drawing, set up some fields in the format to be filled out automatically when you bring the part into the drawing. RMB click anywhere on the drawing sheet (on the paper), and select Edit Sheet Format. 4. Zoom in to the lower right-hand corner of the drawing. Notice that there are several variables with the format $PRPSHEET:{Description}. These are annotations that are linked to custom properties. Some of them have properties with values (such as the Scale note), and some of the properties do not have values (such as the Description).
175
5
10_080139 ch05.qxp
3/26/07
Part I
3:33 PM
Page 176
SolidWorks Basics
Sheet versus Format
W
ith new and even experienced users, there is some confusion around the Sheet versus Sheet Format issue. Part of the confusion is due to SolidWorks terminology. SolidWorks names the two items Sheet and Sheet Format. In this book, I simply use the terms Sheet and Format, to avoid linking the two items with a common first name. It would be better yet if Format were changed to Border or Title Block so that the name more closely matched the function. (The confusion goes deeper for long-time users because there was a time around SolidWorks 98 when Templates as we know them did not exist, and what is now called the Format was called the Template, which is why templates have the file extension *.slddrt [DRawing Template]). In a SolidWorks drawing, you are either editing the sheet or the format. When editing the sheet, you can perform actions such as view, move, and create views, but you cannot select, move, or edit the lines and text of the drawing border. When editing the format, you can edit the lines and text that make up the drawing border, but the drawing views disappear. Often, users save a template that already uses a format, and save themselves some time by selecting everything all at once when they first select the drawing template for a new drawing. While you cannot change templates after you create a document, you can swap formats, and change sheet sizes.
5. Add an annotation in the Drawn row, in the Date column. You can add annotations by clicking Insert ➪ Annotations ➪ Note, or by activating the Annotations toolbar in the CommandManager and clicking the Note button. Type today’s date as the text of the note. If you are using a SolidWorks default template and a circle appears around your note, then use the Text Format PropertyManager that appears when you are creating a note, expand the Border panel, and change the Circle option to None.
CAUTION
6. Add another note, this time to the Name column. Do not type anything in the note, but use the Link to Properties button in the Note PropertyManager to create a link to a custom property. In the Link to Property dialog box, click the Model in View Specified option in Sheet Properties. Type user in the drop-down text box below the option. This now accesses a custom property in a part or assembly that is put onto this drawing and called “user,” and will put the value where the note is placed. 7. To return to Edit Sheet mode (out of Edit Format mode), select Edit Sheet from the RMB menu. A little text reminder message appears in the lower-right corner on the status bar, to indicate whether you are editing the Sheet or the Format. 8. From the Drawings toolbar, select the Standard 3 View button, or through the menus, click Insert ➪ Drawing View ➪ Standard 3 View. If the Chapter5SimpleMachinedPart document does not appear in the list box in the PropertyManager, then use the Browse button to select it. When you click the OK button, the three drawing views are created.
176
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 177
Creating Simple Parts, Assemblies, and Drawings
9. Drawing views can be sized individually or for each sheet. The Sheet Properties dialog box in Figure 5.21 shows the sheet scale. If this is changed, all of the views on the sheet that use the sheet scale are updated. If you select a view and activate the Drawing View PropertyManager, you can use the Scale panel to toggle from Use Sheet Scale to Use Custom Scale. In the United States, drawings are traditionally made and understood using the Third Angle Projection, which is the ANSI standard. In Europe, drawings typically use First Angle Projection, which is the ISO standard. If you are not careful about making and reading your drawings, then you could make a serious mistake. There are times when in the United States, the SolidWorks software will install with ISO standard templates, which will project views using First Angle Projection.
CAUTION
When using a template that you are unfamiliar with, it is a good idea to check the projection method. To do this, RMB click the drawing sheet and select Sheet Properties. The Type of Projection setting appears in the top middle of the dialog box, as shown in Figure 5.21. This dialog box looks similar to the Sheet Format/Size dialog box, but it has some additional options, including the projection type.
FIGURE 5.21 First-angle versus third-angle projections
10. To create an Isometric view, activate the Drawings toolbar in the CommandManager, and click the Projected View button. Then select one of the existing views, and move the cursor at a 45-degree angle. If you cannot place the view where you would like it to go, then press the Ctrl key to break the alignment, and place the view where you want it.
177
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 178
SolidWorks Basics
11. You can change the appearance of the drawing view in several ways.
n View ➪ Display ➪ Tangent Edges with Font uses phantom line type for any edge between tangent faces. n View ➪ Display ➪ Tangent Edges Removed completely removes any tangent edges. This is not recommended, especially for parts with a lot of filleted edges, because it generally displays just the outline of the part. n Shaded or Wireframe modes can be used on drawings, accessed from the View toolbar. n Perspective views must be saved in the model as a named view and placed in the drawing using the view name. n RealView drawing views are not available on a drawing except by capturing a screen shot from the model and placing this screen shot in a drawing. The same applies to PhotoWorks renderings. 12. Look at the custom properties that you created in the title block. The date is there because you entered a specific value for it, but the Name field is not filled in. This is because there is no User property in the part. RMB click the part in one of the views and select Open Part. In the part window, click File ➪ Properties, and in the Property Name column, type the property name user, with a value of your initials, or however your company identifies people on drawings. The Properties dialog box, also called Summary Information, is shown in part in Figure 5.22.
FIGURE 5.22 The Custom Properties entry table
When used in models and formats, Custom Properties are an extremely powerful combination, especially when you want to automatically fill in data in the format, in a BOM, or a PDM product. These topics are discussed in more detail in Chapters 20 and 24.
CROSS-REF
13. When you flip back to the drawing (using Ctrl+Tab), the Name column now contains the value of your initials.
178
10_080139 ch05.qxp
3/26/07
3:33 PM
Page 179
Creating Simple Parts, Assemblies, and Drawings
14. Click the Section View button on the Drawings toolbar. This activates the Line command so that you can draw a section line in a view. When sketching, a line can go either on the Sheet or in a view. This is similar to the distinction between the Sheet and the Format. To make a section view, the section line sketch must be in the view. You will know that you are sketching in a view when a pink border appears around the view. You may also use Lock View Focus from the RMB menu to manually control the view. 15. Bring the cursor down to the circular edge of the slot to activate the center point of the arc. Once the center point is active, you can use the dotted inference lines to ensure that you are lined up with the center. Another option is to manually create sketch relations. Turning on temporary axes displays center marks in the centers of arcs and circles. Figure 5.23 shows the technique with the inference lines being used. Draw the section line through the slot, and then place the section view.
FIGURE 5.23 Creating a section view
16. As mentioned earlier, you can use two fundamentally different methods for dimensioning drawings:
n Model Items imports the dimensions used to build the SolidWorks model and uses them on the drawing. These dimensions are bi-directionally associative, meaning that changing them on the drawing updates the model, and changing them on the model updates them in the drawing. On the surface of things, this sounds too good to be
179
5
10_080139 ch05.qxp
Part I
3/26/07
3:33 PM
Page 180
SolidWorks Basics
true, and it is. The potential problems are that you might not model things the way you would dimension them for the shop. You have to answer several questions for yourself such as do the leader lines go to the right locations or can they be moved and the dimensions usually come in in such a way that they require quite a bit of moving them around. n Reference (driven) Dimensions can be applied to the drawing view directly. These are only associative in one direction, meaning that they measure what is there, but they do not drive the size or position of the geometry. All changes must be made from the model. Again, on the face of things, this appears to be redundant and a waste of time, but in my personal estimation, by the time you finish rearranging dimensions, checking to ensure that you have everything you need, and hiding the extraneous dimensions, you are usually far better off using reference dimensions.
BEST PRACTICE
Users have strong opinions on both sides of this issue. The best thing for you to do is to use both methods and decide for yourself.
17. If you choose to use the Model Items approach, you can do this by clicking Insert ➪ Model Items. Then specify whether the dimensions should come from the entire model or just a selected feature. You also need to ask whether the dimensions should come into all views or just the selected one, and whether you want just a certain type of dimension, annotation, or reference geometry. 18. Once the dimensions are brought in, you need to move some of them from one view to another, which you can do by Shift-dragging the dimension from the old location to the new location. Ctrl-dragging predictably copies the dimension. You can move views by dragging an edge in the view.
Summary Part I, “SolidWorks Basics,” has laid the foundation for the more detailed information that will follow. In the chapters in Part I, I have tried to give recommendations and answer questions that help you to develop an intuition for how SolidWorks software operates, which is the most crucial kind of knowledge when troubleshooting a modeling or editing problem. This chapter has glossed over many of the important details in order to give you a quick overview of the basic functionality in SolidWorks for the three main data types: Parts, Assemblies, and Drawings. From here, Part II, “Building Intelligence into Your Parts,” discusses in more detail how you can accomplish parametric design in SolidWorks.
180
11_080139 pt02.qxp
3/26/07
3:34 PM
Page 181
Building Intelligence into Your Parts IN THIS PART Chapter 6 Getting More from Your Sketches Chapter 7 Choosing a Feature Type Chapter 8 Patterning and Mirroring Chapter 9 Using Equations Chapter 10 Working with Part Configurations Chapter 11 Editing and Evaluation
11_080139 pt02.qxp
3/26/07
3:34 PM
Page 182
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 183
Getting More from Your Sketches
D
esign work would be so much nicer if you could only start with a clean screen every time. Unfortunately, this is rarely the case. Design turns out to be mainly about change. For example, when it comes to sketches, you draw the sketch once, and then you change it several times. Rarely are you able to do something fresh. Because you will spend more time editing than drawing completely new sketches, it makes sense to focus on learning how to edit them. In addition to editing sketches, this chapter covers sketch tools such as sketch pictures, which you can use for tracing; sketch text; and colors and line fonts, which you can use to make reference sketch entities distinguishable from other model elements.
IN THIS CHAPTER Editing sketch relations Copying and moving sketch entities Using sketch pictures Using sketch text Using colors and line styles with sketches Tutorial: Editing and copying
Editing Sketch Relations
Tutorial: Pictures, text, colors, and styles
When I was teaching SolidWorks reseller classes, I frequently told my classes, “Delete is not an edit option.” You will find that this is good advice. There are times to use the Delete command, but you should use it only when it is really necessary. In my own work, I sometimes go to extreme lengths to avoid deleting sketch entities, just to stay in practice. The main reason for not deleting sketch entities is that when you are editing a sketch that has other features that are dependent on it, the dependent features may lose their references, or go dangling. Because of this, even when you can use the Delete command instead of editing, it is still a good practice to edit instead. Deleting relations is not as critical as deleting sketch entities, unless the relations are referenced by equations or design tables.
183
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 184
Building Intelligence into Your Parts
Display/Delete relations Display/Delete Relations is your primary tool when dealing with sketch relations. It is particularly useful to sort relations by the various categories that are shown in Figure 6.1. Sketch relations in the Display/Delete Relations dialog box can be divided into the following categories: n All in This Sketch: Shows all of the relations in the active sketch. n Dangling: Shows only the dangling relations. Dangling relations appear in a brownishgreen or olive color, and represent relations that have lost one of the entities that drives the relation. You can repair dangling relations by selecting the entity with the dangling relation, and then dragging the red dot onto the entity to which it should have the relation. n Overdefining/Not Solved: Overdefined relations are any set of conflicting or redundant instructions that are given to a sketch entity, and appear in red. For example, if a line is collinear with an edge and also vertical, but the edge itself is not vertical, then both the collinear and vertical relations appear in red.
FIGURE 6.1 The Display/Delete Relations PropertyManager
184
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 185
Getting More from Your Sketches
The Not Solved condition often accompanies Overdefined. Not Solved typically refers to a dimension or relation that cannot be applied because of the conflict. The lower-right corner of the screen and the status bar show flags warning that the sketch is overdefined, as shown in Figure 6.2.
FIGURE 6.2 An overdefined sketch
When an overdefined situation exists, all of the relations and dimensions in a sketch may often become overdefined. This can look like a daunting task to repair, when the entire problem is caused by a single relation. Do not automatically delete everything. Instead, try deleting or suppressing the last dimension or relation that was added. You can suppress a dimension by setting it to Driven in the RMB (right-mouse button) menu, and you can suppress relations in the Display/Delete Relations PropertyManager. n External: External relations connect with an entity outside the active sketch. This includes the part Origin, or any model edges. The term external relations is also sometimes meant to signify any relations outside of the part. n Defined in Context: Any relation between parts in an assembly is considered an in-context relation. n Locked: External relations (outside the part) may be locked or broken to increase speed and to lock out changes. n Broken: See Locked. n Selected Entities: Sketch relations are shown only for the selected sketch entities.
CROSS-REF
In-context design, also called top-down, as well as locked and broken relations, are covered in detail in Chapter 16.
Some of the relations listed in the Display/Delete Relations dialog box may be colored to signify the state of the relation. Unfortunately, colored relations are typically placed at the top of the list to attract attention, but when you select them, they are always a dark blue, and so the advantage of color-coding is defeated. The only way around this is to select a relation other than the first one in the list. If there is only one relation in the list, you cannot see the state color.
CAUTION
185
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 186
Building Intelligence into Your Parts
A setting in Tools, Options controls the display of errors. You can select Tools ➪ Options ➪ FeatureManager to find an option called Display Warnings, where you can choose Always, Never, and All but Top Level. When a sketch contains sketch relations with errors, they display as warning signs on the sketch, and will propagate to the top level of a part or assembly if you have chosen the Always option.
SketchXpert The SketchXpert, shown in Figure 6.3, can help you to diagnose and repair complex sketch relation problems. The Diagnose button at the top creates several possible solutions that you can toggle through using the forward and backward arrow buttons in the Results panel. The Manual Repair button displays all of the relations with errors in a window and allows you to delete them manually.
FIGURE 6.3 The SketchXpert dialog box
186
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 187
Getting More from Your Sketches
By selecting the option at the very bottom of the dialog box, you can make the SketchXpert display any time that a sketch error occurs. To display the SketchXpert manually instead of automatically, you can access it by RMB clicking in a sketch.
Copying and Moving Sketch Entities SolidWorks offers several different tools to help you move sketch entities around in a sketch. In SolidWorks, it is usually recommended to keep the sketch as simple as you can, and to create patterns using feature patterns rather than sketch patterns. The following section discusses the main tools for moving and copying sketch entities.
Move entities Move entities enables you to move selected sketch entities by either selecting From and To points, or by typing in XY coordinates for the move. This entity detaches segments whose endpoints are merged, as shown in Figure 6.4. All of these tools have a pushpin icon in the interface, which allows you to use them many times when the pushpin icon is pushed in; they are deactivated after one use if the pushpin icon is not pushed in.
FIGURE 6.4 Using move entities
Rotate entities Rotate entities rotates selected entities in a sketch in the same way that Move entities works. You can drag the angle or type it in manually. The green check mark icon is on the RMB, as shown in the cursor display in Figure 6.5.
187
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 188
Building Intelligence into Your Parts
FIGURE 6.5 Using the Rotate entities feature
The Keep Relations option does not actually keep any relations — it deletes the Horizontal and Vertical relations in the sketch, as shown in Figure 6.5 — but it does keep the merged endpoints, as shown in the right-most image of Figure 6.5. This can be useful, especially considering how many sketch relations it would take to make a sketch move like this naturally.
Copy entities The Copy Entities tool works exactly like the Move Entities tool, except that it copies instead of moving.
Scale entities Scale entities is one of those functions that is probably best left alone. This is because the results appear erratic and unpredictable, particularly if there are dimensions on the sketch. This tool works on a selection of entities, particularly on an isolated selection that is not connected to other entities in the sketch. The PropertyManager for the Scale Entities tool is shown in Figure 6.6.
Modify sketch The Modify Sketch tool has been available in SolidWorks for a long time, but it has been superseded by some of the newer tools mentioned above. However, it still has some unique functionality that is not covered by any other sketch tool. Modify sketch works on the entire sketch rather than on selections from the sketch, and it works best if there are no external relations. It can also work on a sketch without the sketch being active. While most features have been moved to the PropertyManager, Modify sketch still uses a dialog box that floats in the graphics window, as shown in Figure 6.7.
188
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 189
Getting More from Your Sketches
FIGURE 6.6 The Scale PropertyManager
FIGURE 6.7 The Modify Sketch dialog box
Scale About The scaling function in the Modify Sketch tool enables you to scale about either the part Origin or the Moveable Origin. The Moveable Origin is the black origin symbol with knobs on the ends of the axes and at the intersection. The Moveable Origin can be moved and even snapped to entities that are internal or external to the sketch.
Translate The Translate function of the Modify Sketch tool enables you to click and drag to move the entire sketch, or to select a point and move it to a specific set of coordinates that you type in. If the sketch is dragged onto an external entity and picks up an automatic relation, then a message may appear that you can now use Modify sketch only for rotating the sketch because there is an external relation.
189
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 190
Building Intelligence into Your Parts
Rotate The Rotate function of the Modify Sketch tool enables you to position the Moveable Origin to act as the center of rotation, and to either type in a rotation angle or drag with the RMB to rotate, as indicated by the cursor.
Mirroring When you place the cursor over the knobs on the Moveable Origin, the cursor symbols change to indicate the functionality of the RMB. These cursors are shown in action in Figure 6.8. The cursors enable mirroring about X, Y, or both simultaneously.
FIGURE 6.8 The Modify Sketch tool cursors
Copy and paste Probably the simplest way to copy sketch entities in a sketch is to select the entities and use Ctrl+C and Ctrl+V or one of the many other methods available for this purpose (such as the RMB menu, the Edit menu, and Ctrl-dragging). In addition to selected entities within an active sketch, you can also select a sketch from the FeatureManager and copy or paste it to a selected plane or planar face. This creates a new sketch feature in the FeatureManager that has no relation to the original, although it does maintain internal dimensions and relations. This is particularly useful when setting up certain types of lofts that use several profiles that can be created from a single copied profile. Copying and pasting is a fast and effective method of putting sketches on planes.
Simple drag If a selected set of sketch entities has no external relations, then you can select it as a group and move it without distorting or resizing the sketch.
Derived sketch A derived sketch is a parametrically linked copy. The sketches do not need to have any geometrical relation to one another, but when the parent sketch is changed, the dependent derived copy is updated to stay in sync.
190
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 191
Getting More from Your Sketches
To create a derived sketch, you can select a plane or planar face, Ctrl-select the sketch of which you want to make the parametric copy, and then click Insert ➪ Derived Sketch. When you create a derived sketch, you cannot change its shape; it works like a block of a fixed shape. However, you can change the position and orientation of the derived sketch. Figure 6.9 shows a derived sketch and its parent.
FIGURE 6.9 A derived sketch and its parent
Original sketch
Derived sketch
Using Sketch Pictures Sketch pictures are images that are placed in a sketch on a sketch plane. You can size and rotate the images, give them a transparent background, trace over them, and suppress them. They display as a child of the sketch. Image types that you can use as sketch pictures are BMP, GIF, JPEG, TIFF, and WMF. To bring a picture into a sketch, the sketch must first be active. Click Sketch Picture on the Sketch toolbar (it is not there by default, and so you may need to drag it onto the Sketch toolbar from the Tools ➪ Customize ➪ Commands dialog box). You can also access this command through the menus at Tools ➪ Sketch Tools ➪ Sketch Picture. You cannot use sketch pictures in assembly sketches, but they can be shown in a part sketch in an assembly. To change the size of a sketch picture, you can double-click it and drag one of the handles around the outside of the image. When the picture comes into the sketch, it is usually too big, having been sized at a ratio of 1 pixel to 1 mm. To size a picture accurately, you should include a ruler or an
191
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 192
Building Intelligence into Your Parts
object of a known size in the image. If you cannot do this, the next best thing is to guess the size. Draw a line in your sketch and dimension it to approximately the size of something that is recognizable in the image, and then move the image by clicking and dragging it to lay the dimensioned sketch entity as close over the object in the image as possible. Images are opaque, and you cannot see the model through them, but at the same time, you also cannot see the images through the model. They are like a flat piece of paper that is pasted to the model or hanging in space. Sketch pictures cannot be shown on a drawing associatively. The only way to do this is to capture an image of the sketch picture that is being shown in the model, and putting this image in the drawing. PhotoWorks does not use sketch pictures, either, and PhotoWorks Decals are a separate item altogether. Although the most common use for the sketch picture is as a tracing guide, you can use it for a wide variety of other purposes. For example, any sort of logo, decal, or display that is on a flat surface can be shown as a sketch picture.
TIP
Best practice for using sketch pictures is to put them into a separate sketch near or at the top of the FeatureManager. Even though you can have sketch entities in a Sketch Picture sketch, I prefer to keep them in separate sketches. This is because when you use the sketch entities for an extrude or a loft guide curve, this sketch will be consumed under that feature, which means that the image becomes buried somewhere in your model, rather than being easily accessible at the top of the FeatureManager.
BEST PRACTICE
Three views When building a model from images, it is often helpful to have three or more images from orthogonal views, similar to recreating a part from a 2D drawing. If you have a left and a right view, it may be a good idea to put them on planes that are slightly separated so that the images are not exactly on top of one another, which makes them both hard to see. Putting them on slightly offset planes means that one will be clearly visible from one direction, and the other visible from the other direction. Each sketch picture must be in a separate sketch. Figure 6.10 demonstrates the use of multiple sketch pictures to trace the outline of a vehicle, with the partially complete model shown with the images.
Perspective Perspective in images can make it difficult to size items in the foreground or background. You should be aware of this, as well as that objects at different distances from the camera will appear at distorted sizes. If you are taking the pictures that will be used as sketch pictures, you can minimize the effects of perspective by standing farther away from the object and using zoom on the camera if possible.
192
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 193
Getting More from Your Sketches
FIGURE 6.10 Using multiple sketch pictures
Sharp edges When you are drawing a sketch of an object, you are usually drawing theoretically sharp corners of the model. Real parts usually have rounded corners, and so you may have to use your imagination to project where the 3D surfaces would intersect at an edge. When you are reverse-modeling a part from images, you are not using an exact science. It is better than not being able to put pictures into the sketch, but there is nothing about it that can be considered precise.
Using Sketch Text Sketch text uses TrueType fonts to create text inside a SolidWorks sketch. This means that any TrueType font that you have can be converted to text in solid geometry; this includes Wingdings and symbol fonts. Keep in mind that some characters in certain fonts do not convert cleanly into SolidWorks sketches. Sketch text still has to follow the rules for sketching and creating features such as closed contours, as well as not mixing open and closed contours. You can make sketch text follow a sketch curve; to space it evenly along the curve, you can control character width and spacing, as well as overall size by specifying points or actual dimensions. Sketch text can also be justified right, left, centered and evenly, as well as reversed, rotated, and flipped upside down. Figure 6.11 shows the Sketch Text PropertyManager and some of the possible uses of sketch text.
193
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 194
Building Intelligence into Your Parts
FIGURE 6.11 Examples of sketch text
Overlapping characters
The icons in the Sketch Text PropertyManager are fairly self-explanatory, other than the Rotated Text option, which rotates individual letters, and not the whole string of text. You can use the Sketch Text tool multiple times in a single sketch to make pieces of text with different properties. Each string of text has a placement point located at the lower left of the text. This point can be given sketch relations or dimensions to locate the text.
194
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 195
Getting More from Your Sketches
If the text overlaps in places, as shown in Figure 6.10, you can correct this in a couple of ways. First, you can extrude it with the Merge option turned off so that each letter is created as a separate solid body. You can also explode sketch text so that it becomes simply lines and arcs in a sketch, which you can edit the same as any other sketch.
Using Colors and Line Styles with Sketches Custom colors and line styles are usually associated with drawings, not sketches; in fact, they are most valuable when used for drawings. In sketches, this functionality is little known or used, but is still of value in certain situations.
Color Display mode In drawings, you can use the Color Display Mode button to switch sketch entities on the drawing between displaying the assigned line or layer color and displaying the sketch status color. It has exactly the same effect here in part and assembly sketches. When you press the button, the sketch state colors are used. When the button is not pressed, any custom colors that you have applied to the sketch entities will display. If the button is not pressed and you have not applied colors to the entities, then the default sketch state colors are used. You can use sketch colors for emphasis, to make selected sketch entities stand out, or to make sketches with various functions immediately distinguishable. Color Display mode only has an effect on an active sketch. Once a sketch is closed, it returns to the gray default color for inactive sketch entities.
Line color Line color enables you to assign color to entities in an active sketch. Whether the assigned color or the default sketch status colors are used is determined by the Color Display Mode tool.
Edit color You can use the Edit Color tool to assign color to an entire sketch. The color that you assign in this way displays only when the sketch is inactive, instead of the default gray color. The colors that are assigned to sketches in this way also follow the toggle state of the Color Display Mode button. For example, if the Color Display Mode button is depressed, then inactive sketches display as gray. When the Color Display Mode button is not pressed, then inactive sketches display in any color that you have assigned by using the Edit Color tool.
Line thickness and line style The Line Thickness and Line Style tools function independently from the Color Display Mode button, but they are still used only when the sketch is active. As soon as a sketch that contains entities with edited thickness and style is closed, the display goes back to the normal line weight and font.
195
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 196
Building Intelligence into Your Parts
To assign a thickness or a style, you can select the sketch entities to be changed, press the button, and select the thickness or style. Although a single sketch entity may have only a single thickness or style, you can use multiple thicknesses or styles within a single sketch. Figure 6.12 shows a sketch with the thickness and style edited.
FIGURE 6.12 A sketch with edited line thickness and line style
You can create custom line styles, but only in a drawing document; you cannot use custom line styles in the part environment.
CROSS-REF
Line thickness and line styles are covered in more detail in the discussion of drawings in Chapter 20.
Tutorial: Editing and Copying This tutorial guides you through some common sketch relation editing scenarios and using some of the Copy, Move, and Derive tools. Follow these steps to learn about editing and copying sketches: 1. Open the part named Chapter6 Tutorial1.sldprt from the CD-ROM. This part has several error flags on sketches. In cases where there are many errors, it is best to roll the part back and go through the errors one by one. 2. Drag the rollback bar from just after the last fillet feature to just after Extrude3. If Extrude3 is expanded so that you can see Sketch3 under it, then drop the rollback bar to after Sketch3. If a warning message appears, telling you that Sketch3 will be temporarily unabsorbed, then select Cancel and try the rollback again. Figure 6.13 shows before and after views for the rollback.
196
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 197
Getting More from Your Sketches
3. Edit Sketch3 and turn off the Sketch Relations display (View ➪ Sketch Relations). Click Display/Delete Relations on the toolbar (the Eyeglasses tool), and set it to All in This Sketch. Notice that all of the relations conflict, but only one is unsolvable: the Equal Radius relation. This appears to be a mistake because the two arcs cannot be equal. 4. Delete the Equal Radius relation. The sketch is still not fixed. 5. Click the green check mark icon to close the Display/Delete Relations PropertyManager. 6. RMB click the graphics window and select SketchXpert. Click Diagnose.
FIGURE 6.13 Rolling the part back to Extrude3
Rollback bar
Rollback cursor Model in rolled back state
7. Using the double arrows in the Results panel, toggle through the available solutions. All of the solutions except one remove sketch relations. Accept the one solution that removes the dimension, and click the green check mark icon to exit the SketchXpert. The sketch no longer shows errors. 8. Close the sketch. Notice that the error flag does not disappear until the sketch has been repaired and closed. 9. Use the rollback bar to roll forward to after Extrude2 and Sketch2. Figure 6.14 shows the tooltip message that appears if you place the cursor over the feature with the error. With time, you will begin to recognize the error messages by a single keyword or even by the shape of the message text. This message tells you that there is a dangling relation — a relation that has lost one of the entities.
197
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 198
Building Intelligence into Your Parts
FIGURE 6.14 The Error tooltip
10. Edit the sketch. Figure 6.15 points out the dangling errors. If you show the Sketch Relation icons again, the errors will be easier to identify. When you use Display/Delete Relations, the first two Coincident relations appear to be dangling. Clicking the relation in the Relations panel of the Display/Delete Relations PropertyManager shows that one point was connected to a line and the other point was connected to a point. 11. When you have fixed the errors, exit the sketch and confirm that the flag is no longer on Sketch2. 12. Drag the rollback bar to just before CutExtrude1. Edit 3DSketch1. This sketch is overdefined. If the Sketch Relations are not on at this point, then turn them on again. Because this is a task that you will perform many times, this is a good opportunity to set up a hotkey for this function. As a reminder, to set up a hotkey, go to Tools ➪ Customize ➪ Keyboard, and in the Search box, type relations. In the Shortcut column for this command, select a hotkey to use.
TIP
13. Double-click one of the relation icons; the Display/Delete Relations PropertyManager appears. Notice that one of the sketch relations is a Fixed relation. Remove the Fixed relation, and exit the sketch. 14. RMB click anywhere in the FeatureManager and select Roll To End. 15. Click CutExtrude1 in the FeatureManager so that you can see it in the graphics window, and then click a blank space to deselect the feature. 16. Ctrl-drag any face of the cut feature, and drop it onto another flat face. The Ctrl-drag function copies the feature and the sketch, but the external dimensions and relations become detached.
198
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 199
Getting More from Your Sketches
FIGURE 6.15 Fixing dangling errors
Two points with dangling relations
Drag this point to this corner
Drag this point to this edge
17. In the prompt that appears, click Dangle in response to the prompt. This means that you will have to reattach some dangling dimensions rather than recreating them. Edit the newly created sketch, which now has an error on it. 18. Two of the dimensions that went to external edges now have the olive dangling color. Select one of the dimensions; a red handle displays. Drag the red handle and attach it to a model edge. Do this for both dimensions. The dimensions update to reflect their new locations. Exit the sketch and verify that the error flag has disappeared. 19. Expand CutExtrude1, and select Sketch5 under it. Ctrl-select a flat face on the model other than the one that Sketch5 is on. In the menu, select Insert ➪ Derived Sketch. You are put into a sketch editing the derived sketch. 20. The sketch is blue, and so you should be able to resize it, right? You can test this by dragging the large circle; it only repositions the sketch as a unit.
199
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 200
Building Intelligence into Your Parts
21. Dimension the center of the large circle to the edges of the model. 22. Drag the smaller circle, and notice that it swivels around the larger circle. Create an angle dimension between the construction line between the circle centers and one of the model edges. Notice that the sketch is now fully defined. 23. Exit the sketch, and look at the name of the derived sketch in the FeatureManager. The term derived appears after the name, and the sketch appears as fully defined. 24. RMB click the sketch and select Underive Sketch. Notice that the sketch is now underdefined. The Underive command removes the associative link between the two sketches.
Tutorial: Controlling Pictures, Text, Colors, and Styles This tutorial guides you through some of the miscellaneous functions in sketches, and shows you what they are used for and how they are used. Follow these steps to learn how to control these items: 1. Open a new part using a template with inches as units. Open a sketch on the Front plane, and draw a construction line 12 inches down (negative Y) from the Origin. 2. Insert a sketch picture in this sketch. Use Sketch Picture 1.tif from the CD-ROM for Chapter 6. 3. Resize the image so that the endpoints of the construction line are near the centers of the holes on the ends of the part. To move the image, just double-click it first, and then drag it. To resize it, drag the corners. 4. In the Transparency panel of the Sketch Picture PropertyManager, select the Eyedropper tool and click in the white background of the image. Make sure that the color field next to the Eyedropper tool changes to white. 5. Slide the Transparency and Matching Tolerance sliders all the way to the right, or type 1.00 in the number boxes. 6. Close the sketch, and rename it Sketch Image Front View. 7. Put the image Sketch Picture 2.tif, also from the CD-ROM, on the Right plane, and resize it to fit with the first image. Center it symmetrically about the Origin. Also set the transparency to the same setting as the first image. 8. Open a new sketch, also on the Front plane, and draw two circles to match the features on the ends. Extrude them using a Mid Plane extrusion to match the image in the other direction (about 2.5 inches), as shown in Figure 6.16. 9. Open another new sketch on the Front plane and draw the tangent lines to form the web in the middle of the part. Close the sketch to make a solid extrusion. Extrude this part .5 inches Mid Plane.
200
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 201
Getting More from Your Sketches
FIGURE 6.16 Using sketch pictures
10. Open a new sketch on the face of the large flat web that you created in the previous step, and offset the arc edge of the larger circular boss by 2.1 inches. 11. Change the arc to a construction arc and drag its endpoints to approximately the position shown in Figure 6.17. The endpoints of the arc are blue after you drag them. Give them a Horizontal relation, and then dimension them as shown in Figure 6.17.
FIGURE 6.17 Creating an offset arc
12. Click Tools ➪ Sketch Entities ➪ Text to initiate the creation of sketch text. 13. Select the construction arc to go into the Curves window. 14. In the Text window, type SolidWorks. Select the Full Justify option.
201
6
12_080139 ch06.qxp
Part II
3/26/07
3:36 PM
Page 202
Building Intelligence into Your Parts
15. Deselect the Use Document Font option, click the Font button, and then set the Units to .50 inches. Click the Bold button to make the text thicker. Click OK to exit the dialog box. Click the green check mark icon to exit the sketch text, and then exit the sketch. 16. Extrude the text to a depth of .050 inches with 3 degrees of draft. The part at this point resembles Figure 6.18.
FIGURE 6.18 Creating extruded text
PERFORMANCE
Sketch Text is a real performance killer. The more text that you use, the longer it takes to extrude. Draft on the extrusion adds to the time required.
17. Select the flat face on the other side of the part from where you just extruded the text, and open a sketch. 18. Select the face and click the Offset button to make a set of sketch entities offset to the inside of the face by .50 inches. 19. Turn on the Line Format toolbar (RMB click any toolbar other than the CommandManager and select Line Format). 20. Select all of the sketch lines, and change their color using the Line Color tool. Change the line thickness and the line style using the appropriate tools. The sketch now looks something like Figure 6.19. 21. When you click the Color Display Mode tool, the colors return to regular sketch colors. When you exit the sketch, the line weight and style also return to normal.
202
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 203
Getting More from Your Sketches
FIGURE 6.19 Using line thickness and line style
Summary Many tools that are available in sketches are not commonly shown in the most popular sources of information, including official training manuals. The difference between a good CAD tool and a great communication tool can be some of these minor functions that just make life a little easier, or the presentation or editing of data a little better. When you explore the capabilities of SolidWorks, it usually rewards you with functionality that others might not find.
203
6
12_080139 ch06.qxp
3/26/07
3:36 PM
Page 204
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 205
Choosing a Feature Type
W
henever I do a woodworking project, the most frustrating part of the job is to envision a result, but not be able to accomplish it because I do not have the tools to get it done; worse yet is to actually have the tools but either not understand how to use them or not even realize that I have them. Getting the job done is so much more satisfying when you use the right tools and get the job done right — not just so that it looks right, but so that it really is right.
IN THIS CHAPTER Identifying when to use which tool Creating curve features Filleting
I see users run into the same issues with SolidWorks. SolidWorks offers so many “tools in the toolbox” that it is sometimes difficult to select the best one, especially if it is for a function that you do not use frequently.
Selecting a specialty feature
This chapter helps you to understand how each feature functions, and offers situations when they are best applied or avoided.
Tutorial: Creating a wire-formed part
Identifying When to Use Which Tool I am always trying to think of alternate ways of doing things. Especially when working with complex features, it is important to have a backup plan, or sometimes multiple backup plans. Even when the part is not that complicated, every situation is different. You probably will not get away with just doing blind extrudes and cuts with simple chamfers and fillets for the rest of your career. And even if you could, who would want to?
205
Tutorial: Bracket casting
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 206
Building Intelligence into Your Parts
As an exercise, I often try to see how many different ways a particular shape might be modeled, and how each modeling method relates to manufacturing methods, costs, editability, efficiency, and so on. You may also want to try this approach.
Extrude Extruded features can be grouped into several categories, with extruded Boss and Cut features at the highest level. Boss and Cut are two separate feature types and cannot be interchanged. Sketches may be shared between features or reused after a feature has been deleted. The “Base” part of the Extruded Boss/Base is a holdover from when SolidWorks did not allow multibody parts, and the first feature in a part had special significance that it no longer has. This is also seen in the menus at Insert ➪ Boss/Base. The Base feature was the first solid feature in the FeatureManager, and you could not change it without deleting the rest of the features. The introduction of multibody support in SolidWorks has removed this limitation.
CROSS-REF
Multibody parts are covered in detail in Chapter 26.
Solid Feature In this case, we use the term solid feature as opposed to thin feature. This is the simple type of feature that you create by default when you extrude a closed loop sketch. A closed loop sketch fully encloses an area without gaps or overlaps at the sketch entity endpoints. Figure 7.1 shows a closed loop sketch creating an extruded solid feature.
Thin Feature The Thin Feature option is available to several types of features, but is most commonly used with Extruded Boss features. Thin features are created by default when you use an open loop sketch, but you can also select this option for closed loop sketches. Thin features are commonly used for ribs, thin walls, hollow circular bosses, and many other types of features that are common to plastic parts or castings. Even experienced users tend to forget that thin features are not just for bosses, but can also be used for cuts. For example, you can easily create grooves and slots with thin feature cuts. Figure 7.2 shows the Thin Feature panel in the Extruded Boss PropertyManager. In addition to the default options that are available for the Extrude feature, the Thin feature adds a thickness dimension, as well as three options to direct the thickness relative to the sketch: One-Direction, Mid-Plane, and Two-Direction. The Two-Direction option requires two dimensions, as shown in Figure 7.2.
206
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 207
Choosing a Feature Type
FIGURE 7.1 A closed loop sketch and an extruded solid feature
FIGURE 7.2 The Thin Feature interface
Thin feature sketches are simpler, which always means that they are more robust through changes. You can create the simplest cube from a single sketch line and a thin feature extrude. However, in some respects, they are not as flexible when the design intent changes. For example, if a part is going to change from a constant width to a tapered or stepped shape, thin features do not handle this kind of change well. Figure 7.3 shows different types of geometry that are created from thin features.
207
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 208
Building Intelligence into Your Parts
FIGURE 7.3 Different types of geometry created from thin features
Sketch types I have already mentioned several sketch types, including closed loop and open loop. Closed loop sketches make solid features by default, but you can also use them to make thin features. Open loop sketches make thin features by default, and you cannot use them to make solid features.
Sketch contours Sketch Contour is a feature that is used in other competing CAD packages and that SolidWorks has adopted, probably more to match features in the competing software than to create a better way of doing things. Using sketch contours seems to promote sloppy work, although in some cases, they act as valid time savers. In general, sketch contours enable you to select enclosed areas where the sketch entities themselves actually cross or otherwise violate the usual sketch rules. One of these conditions is the selfintersecting contour.
208
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 209
Choosing a Feature Type
SolidWorks works best with well-disciplined sketches that follow the rules. As a result, if you plan to use sketch contours, then you should make sure that it is not simply because you are unwilling to clean up a messy sketch.
BEST PRACTICE
When you define features by selecting sketch contours, they are more likely to fail if the selection changes when the selected contour’s bounded area changes in some way. It is best practice to use the normal closed loop sketch when you are defining features. Contour selection is best suited to “fast and dirty” conceptual models, which are used in very limited situations for production models.
As shown in Figure 7.4, there are several types of contour selection.
3D sketch You can make extrusions from 3D sketches, even 3D sketches that are not planar. While not necessarily the best way to do extrudes, this is a method that you can use when needed. You can establish direction for an extrusion by selecting a plane (normal direction), axis, sketch line, or model edge.
FIGURE 7.4 Types of contour selection
Selecting an enclosed area from a single self-intersecting profile
Selecting multiple areas as contours in a sketch
Selecting the border as a contour
209
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 210
Building Intelligence into Your Parts
When you make an extrusion from a 3D sketch, the direction of extrusion cannot be assumed or inferred from anything — it must be explicitly identified. Extrusion direction from a 2D sketch is always perpendicular to the sketch plane unless otherwise specified. Non-planar sketches become somewhat problematic when you are creating the final extruded feature. The biggest problem is how you cap the ends. Figure 7.5 shows a non-planar 3D sketch that is being extruded. Notice that the end faces are, by necessity, not planar, and are capped by an unpredictable method. This is a problem only if your part is going to use these faces in the end; if it does not, then there may be no issue with using this technique. If you would like to examine this part, it is included on the CD-ROM as Chapter 7 Extrude 3D Sketch.sldprt.
FIGURE 7.5 Extruding a non-planar 3D sketch
If you need to have ends with a specific shape, and you still want to extrude from a non-planar 3D sketch, then you should use an extruded surface feature rather than an extruded solid feature.
CROSS-REF
Surfacing features are covered in detail in Chapter 27. Chapter 5 contains additional details on extrude end conditions, thin features, directions, and the From options.
Revolve Like all other features, revolve features have some rules that you must observe when choosing sketches that can be used to create a revolve: n Draw only half of the revolve profile (draw the section to one side of the centerline). n The profile must not cross the centerline.
210
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 211
Choosing a Feature Type
n The profile must not touch the centerline at a single point. It can touch along a line, but not at a point. Revolving a sketch that touched the centerline at a single point would create a point of zero thickness in the part. You can use any type of line or model edge for the centerline, not just the centerline/construction line type.
End conditions There are three Revolve end conditions: n One-Direction: The revolve angle is driven in a single direction. n Two-Direction: The revolve angle can be driven in two independent directions. n Mid-Plane: The revolve angle is divided equally in opposite directions. There is no equivalent for Up to Vertex, Up to Next, Up to Surface, or Up to Body with the Revolve feature.
Contour selection Like extrude features, revolve features can also use contour selection; as with the extrude features, I recommend that you avoid using contours.
Loft Many users struggle when faced with the option to create a loft or a sweep. Some overlap exists between the two features, but as you gain some experience, it becomes easier to choose between them. Generally, if you can create the cross-section of the feature by manipulating a single sketch, then a sweep might be the best feature. If the cross-section changes character or severely changes shape, then a loft may be best. If you need a very definite shape at both ends and/or in the middle, then a loft is a better choice because it allows you to explicitly define the cross-section at a point. However, if the outline is more important than the cross-section, then you should choose a sweep. If the path between ends is important, choose a sweep. If the ends themselves are more important and you just want to blend from one end to the other, then the loft is the better choice. Both types of features are extremely powerful, but the sweep has a tendency to be fussier about details, setup, and rules, while the loft can be surprisingly flexible. I am not trying to dissuade you from using sweeps, because they are useful in many situations. However, in my own personal modeling, I probably use about ten lofts for every sweep. For example, while you would use a loft or combination of loft features to create a complex laundry detergent bottle, you would use the sweep to create a raised border around the label area. Lofts are an example of interpolated geometry. That is to say that the loft is outlined by creating several loft sections and guide curves, and then the software interpolates the face geometry in between the sections. A good example of this is to put a circle on one plane and a rectangle on an
211
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 212
Building Intelligence into Your Parts
offset plane and then loft them together. This arrangement is shown in Figure 7.6. The transition between shapes is the defining characteristic of a loft, and is also the reason for choosing a loft instead of another feature type. Lofts can create both Boss features and Cut features.
FIGURE 7.6 A simple loft
The two-profile loft with default end conditions always creates a straight transition, which is shown in the image to the left. A two-point spline with no end tangency creates a straight line in exactly the same way. By applying end conditions to either or both of the loft profiles, the loft’s shape is made more interesting, as seen in the image to the right in Figure 7.6. Again, the same thing happens when applying end tangency conditions to a two-point spline: it goes from being a straight line to being more curvaceous, with continuously variable curvature. The Loft PropertyManager interface is shown in Figure 7.7.
Entities that you can use in a loft For solid lofts, you can select faces, closed loop 2D or 3D sketches, and surface bodies. You can use sketch points as a profile on the end of a loft that comes to a point or rounded end. For surface lofts, you can use open sketches and edges in addition to the entities that are used by solid lofts. Some special functionality becomes available to you if you put all of the profiles and guide curves together in a single 3D sketch. In order to select profiles made in this way, you must use the SelectionManager, which is discussed later in this chapter. The Sketch Tools panel of the Loft PropertyManager enables you to drag sketch entities of any profile made in this way while you are editing or creating the Loft feature, without needing to exit and edit a sketch.
212
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 213
Choosing a Feature Type
FIGURE 7.7 The Loft PropertyManager
While this sort of functionality may be attractive for a lot of reasons, you should not choose this way. Unless you are dealing with the simplest of geometry and sketch relations, 3D sketches — and more specifically 3D sketch planes — are simply not up to the task. It is definitely true that 3D sketches in SolidWorks work far better than they used to, but I would still not put even a 3D sketch of medium complexity in a part that I had to depend on for production data. The specific problem is sketch relations. I discuss 3D sketches in more detail in Chapter 31.
CAUTION
The similarities between lofts and splines The words “loft” and “spline” come to us from the shipbuilding trade. The word “spline” is actually defined as the slats of wood that cover the ship, and the spars of the hull very much resemble loft sections. With the splines or slats bending at each spar, it is easy to see how the modern CAD analogy came to be.
213
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 214
Building Intelligence into Your Parts
Lofts and splines are also governed by similar mathematics. You have seen how the two-point spline and two-profile loft both create a straight-line transition. Next, a third profile is added to the loft and a third point to the spline, which demonstrates how the math that governs splines and lofts is also related to bending in elastic materials. Figure 7.8 shows how lofts and splines react geometrically in the same way that bending a flexible steel rod would react (except that the spline and the loft do not have a fixed length).
FIGURE 7.8 Splines, lofts, and bending
Three-point spline, no end conditions
End tangency changed
Notice slight bulge, just like a real rod in bending
Reacts like a pinned joint
With this bit of background, it is time to move forward and talk about a few of the major aspects of Loft features in SolidWorks. It is probably possible to write a separate book that only discusses modeling lofts and other complex shapes. In this single chapter, I do not have the space to cover the topic exhaustively, but coverage of the major concepts will be enough to point you in the right direction.
The need for surfaces In this chapter, I deal exclusively with solid modeling techniques because they are the baseline that SolidWorks users use most frequently. Surfaces make it easier to discuss complex shape concepts because surfaces are generally created one face at a time, rather than by using the method with solid modeling that creates as many faces as necessary to enclose a volume. From the very beginning, the SolidWorks modeling culture has made things easier for users by taking care of many of the details in the background. This is because solids are built through automated surface techniques. Surface modeling in itself can be tedious work because of all of the
214
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 215
Choosing a Feature Type
manual detail that you must add. Solid modeling as we know it is simply an evolutionary step that adds automation to surface modeling. The automation maintains a closed solid boundary around the volume. Because surfaces are the underlying building blocks from which solids are made, it would make sense to teach surfaces first, and then solids. However, the majority of SolidWorks users never use surfacing, and do not see a need for it, and so surface functions are generally given a lower priority.
CROSS-REF
You can refer to Chapter 27 for surfacing information.
Loft end constraints Loft end conditions control the tangency direction and weighting at the ends of the loft. Some of the end constraints depend upon the loft starting or ending from other geometry. The optional constraints include the following:
None The direction of the loft is not set by the None end constraint, but the curvature of the lofted faces at the ends is zero. This is the default end constraint for two-section lofts.
Default The Default end constraint is not available for two-section lofts, only for lofts with three or more sections. This end constraint applies curvature to the end of the loft so that it approximates a parabola being formed through the first and last loft profiles. The SolidWorks help file makes a special point to explain the difference between the None and Default end constraints, but the Default help makes it look as if it works with only two profiles, when in fact it does not.
Tangent to Face The Tangent to Face end constraint is self-explanatory. This end constraint may fail or cause unwanted ripples or puckers in the part if profiles that are adjacent to one another or touch at an edge are lofted together. The Tangency to Face option includes a setting for tangent length. This is not a literal length dimension, but a relative weighting, on a scale from 0.1 to 10. The small arrow to the left of the setting identifies the direction of the tangency. Usually, the default setting is correct, but there are times when SolidWorks misidentifies the intended tangency direction, and you may need to correct it manually. The Next Face option is available only when lofting from an end face where the tangency could go in one of two perpendicular directions. This is shown in Figure 7.9. Apply to All refers to applying the Tangent Length value to all of the tangency-weighting arrows for the selected profile. When you select Apply to All, only one arrow displays. When you deselect it, one arrow should display for each vertex in the profile, and you can adjust each arrow individually.
215
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 216
Building Intelligence into Your Parts
FIGURE 7.9 Examples of end constraints
None
Default
Tangent to Face
Tangency to Face with Other Face option
Both ends set to Normal to Profile
Tangent to Face
Direction vector
Curvature to Face The difference between tangency and curvature is that tangency is only concerned with the direction of curvature immediately at the edge between the two surfaces. Curvature must be tangent and in addition match the radius of curvature on either side of the edge between surfaces. This is often given many names, including curvature continuity, c2, and others. Lofted surfaces do not usually have a constant radius; because they are like splines, they are constantly changing in local radius.
216
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 217
Choosing a Feature Type
Direction Vector The Direction Vector end constraint forces the loft to be tangent to a direction that you define by selecting an axis, edge, or sketch entity. The angle setting makes the loft deviate from the direction vector, as shown in Figure 7.9. The curved arrows to the left identify the direction in which the angle deviation is going.
Isoparameter U-V lines The mesh or grid shown in the previous images appears automatically for certain types of features, including lofts. The grid represents isoparameter lines, also known as NURBS mesh or U-V lines. This mesh shows the underlying structure of the faces being created by the feature. If the mesh is highly distorted and appears to overlap in places, then it is likely that the feature will fail. You can show or hide the mesh through the RMB menu when editing or creating a Loft feature, unless the SelectionManager is active. In this case, you can see only SelectionManager commands in the RMB menu. In addition, planar faces do not mesh, only faces with some curvature.
Guide curves Guide curves help to constrain the outline of a loft between loft profiles. Although it is best to try to achieve the shape you want by using appropriately shaped and placed loft profiles, I recognize that this is not always possible. The most appropriate use of guide curves for solid lofts is at places where the loft is going to create a hard edge, which is usually at the corners of loft profile sketches. Guide curves often (but not always) break up what would otherwise be a smooth surface, and you should avoid them in these situations, if possible. Do not try to push the shape of the loft too extremely with guide curves. Guide curves should be used mainly for tweaking and fine-tuning rather than coarse adjustment. Use loft sections and end constraints to get most of the overall shape correct. Pushing too hard with a guide curve can cause the shape to kink unnaturally.
BEST PRACTICE
Although guide curves may be longer than the loft, they may not be shorter. The guide curve applies to the entire loft. If you need to apply the guide curve only to a portion of the loft, then split the loft into two lofts, one that uses the guide curve, and the other that does not. The guide curve must intersect all profiles in a loft. If you have more than one guide curve, the order in which they are listed in the box is important. The first guide curve helps to position the intermediate profiles of the loft. It may be difficult or impossible to visualize the effects of guide-curve order before it happens, but remember that it does make a difference, and depending on the difference between the curves, the difference may or may not be subtle. Guide curves are also used in sweeps, which are dealt with later in this chapter. Figure 7.10 shows a model that is lofted using guide curves. The image to the left shows the sketches that are used to make the part. There are two sketches with points; you can use points as loft profiles. The image in
217
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 218
Building Intelligence into Your Parts
the middle shows the Loft feature without guide curves, and to the right is the part with guide curves. If you would like to examine how this part is built, you can find it on the CD-ROM with the filename Chapter 7 Guide Curves.sldprt.
FIGURE 7.10 A loft with and without guide curves
Loft profiles Middle profile
Centerline lofts The Centerline panel of the Loft PropertyManager is used to set up a Centerline loft. You can use the Centerline of a loft in roughly the same way that you use a sweep path. In fact, the Centerline loft resembles a sweep feature where you can specify the shape of some of the intermediate profiles. Centerline lofts can also create intermediate profiles. You may prefer to use a centerline loft instead of either a sweep or a regular loft because the profile may change in ways that the Sweep feature cannot handle, and the loft may need some guidance regarding the order of the profiles or how to smooth the shape between the profiles. Sweep features are covered later in this chapter. If you are creating a centerline loft, then you may want to examine the sweep functionality as well. You can use centerlines simultaneously with guide curves. While guide curves must touch the profile, there is no such requirement for a centerline; in fact, the centerline works best if it does not touch any of the profiles. The slider in the Centerline Parameters panel enables you to specify how many intermediate sections to create between sketched profiles.
218
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 219
Choosing a Feature Type
SelectionManager The SelectionManager simplifies the selection of entities from complex sketches that are not necessarily the clean, closed loop sketches that SolidWorks works with most effectively.
NEW FEATURE
The SelectionManager is new in SolidWorks 2007, and is used only for loft, sweep, and boundary surface features. It replaces Smart Selection and Contour Selection for these
features.
The SelectionManager has been implemented in a limited number of features, and has limited functionality compared with the other selection options that are available in SolidWorks. Selection options in the SelectionManager include the following: n OK: Accepts the selection. This feature is also available on the RMB. n Cancel: Quits the SelectionManager n Clear: Clears the current selection set n Pushpin: Keeps the SmartSelection window available, even when it is not required for sketch entity selections n Select Closed Loop: You can select two different types of loops with this tool: n A parametric closed loop in a 2D or 3D sketch n A parametric loop of edges around a surface n Select Open Loop: Selects a chain (end-to-end sketch entities) n Select Group: Selects entities individually. If you click the Propagate symbol, all tangent edges are selected. n Select Region: Works like the Contour Selection described earlier in this chapter. n Standard Selection: Disables special functions of the SelectionManager. This feature works like a regular selection tool. n Auto OK Selections: Enabled when you use the Pushpin feature. This feature works for closed and open loop selection.
Loft options You can choose from the following Loft options, as shown in Figure 7.11: n Merge Tangent Faces: Model faces that are tangent are merged into a single face. This is done behind the scenes by converting profiles into splines, which make approximations but are smoother than sketches with individual tangent line and arc entities.
219
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 220
Building Intelligence into Your Parts
FIGURE 7.11 Loft options
n Close Loft: A closed loop is made of the loft. At least three loft profiles must exist in order to use this option. Figure 7.12 shows a loft where the Close Loft option is used, and the loft sections are shown. This model is on the CD-ROM with the filename Chapter 7 — Closed Loft.sldprt.
FIGURE 7.12 A closed loft
n Show Preview: This turns the preview of the Loft feature on or off, if the feature is not going to fail. All of the following loft preview options are system options, and remain on until you turn them off. n Transparent Preview is available from the RMB menu when you edit a loft, if the SelectionManager is not active. n Mesh Preview is also available on the same RMB menu. n Zebra Stripe Preview is also available on the same RMB menu, and is covered in more depth in Chapter 11. n Merge Result: Merges the resulting solid body with any other solid bodies that it may contact.
220
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 221
Choosing a Feature Type
Sweep The Sweep feature uses more than one sketch. A sweep is made from a profile (cross-section) and a path, and can create a boss or a cut feature. If you want, you can also use guide curves. Sweeps can run the gamut from simple to complex. Typical simple sweeps are used to create wire, tubing, or hose. More complex sweeps are used for creating objects such as bottles, involutes, and corkscrews. The main criteria for selecting a sweep to create a feature are that you must be able to identify a cross-section and a path. The profile (cross-section) can change along the path, but the overall shape must remain basically the same. The profile is typically perpendicular to the path, although this is not a requirement.
Simple sweep An example of a simple sweep is shown in Figure 7.13. The paper clip uses a circle as the profile, and the coiled lines and arcs as the path.
FIGURE 7.13 A simple sweep feature
Profile or cross-section Sweep path
Simple sweeps such as that shown in Figure 7.13 essentially set up SolidWorks to create geometry from simpler features such as Extrude and Revolve. If you look at the faces, you can see that they are created from straight lines and arcs, which lend themselves well to extrudes and revolves.
Sweep with guide curves More complex sweeps begin to control the size, orientation, and position of the cross-section as it travels through the sweep. When you use a guide curve, several analogies can be used to visualize how the sweep works. The cross-section/profile is solved at several intermediate positions along the path. If the guide curve does not follow the path, the difference between the two is made up by
221
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 222
Building Intelligence into Your Parts
adjusting the profile. Consider the following example. In this case, the profile is an ellipse, the path is a straight line, and there are guide curves that give the feature its outer shape. Figure 7.14 shows all of these elements and the finished feature.
FIGURE 7.14 A sweep with two guide curves
ON the CD-ROM
The part shown in Figure 7.14 is on the CD-ROM with the filename Chapter7 Bottle.sldprt.
The sweep with guide curves does not create extrudes and revolves, although you can use simple lines and arcs with this feature. The changes in the cross-section are created from a more complex feature type, namely a loft. The PropertyManager for the Sweep function includes an option for Show Sections, which in this case creates almost 200 intermediate cross-sections. These sections are used to create a loft. You can think of complex sweeps as an automated setup for an even more complex loft. It is helpful to envision features such as this when you are troubleshooting or setting up more complex sweeps. If you open the part mentioned previously from the CD-ROM, you can edit the Sweep feature to examine the sections for yourself. In most other published SolidWorks materials that cover these topics, sweeps are covered before lofts because many people consider lofts to be the more advanced topic. However, I have put lofts first because understanding lofts is necessary before you can understand complex sweeps, as complex sweeps really are just lofts.
Pierce relation The Pierce sketch relation is the only sketch relation that applies to a 3D out-of-plane edge or curve without projecting the edge or curve into the sketch plane. It acts as if the 3D curve is a length of thread and the sketch point is the eye of a needle, where the thread pierces the needle
222
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 223
Choosing a Feature Type
eye. The Pierce relation is most important in the Sweep feature when it is applied in the profile sketch between endpoints, center points, or sketch points and the guide curves. This is because the Pierce relation determines how the profile sketch will be solved when it is moved down the sweep path to create a new intermediate profile. Figure 7.15 illustrates the function of the Pierce relation in a sweep with guide curves. The dark section on the left is the sweep section that is sketched. The lighter sketches to the right represent the intermediate profiles that are automatically created behind the scenes.
FIGURE 7.15 The effects of the Pierce relation
Guide curve
Pierce relation forces contact
Sketched sweep profile
Figure 7.16 shows a more complicated 3D sweep, where both the path and the guide curve are 3D curves. I cover 3D curves toward the end of this chapter, and so you can refer ahead to these features to understand how this part is made.
ON the CD-ROM
The part shown in Figure 7.16 is on the CD-ROM with the filename Chapter 7 3D Sweep.sldprt.
This part is created by making a pair of tapered helices, with the profile sketch plane perpendicular to the end of one of the curves. The taper on the outer helix is greater than on the inner one, which causes the twist to become larger in diameter as it goes up. To make the circle follow both helices, you must create two pierce relations, one between the center of the circle and a helix, and the other between a sketch point that is placed on the circumference of the circle and the other helix. This means that the difference in taper angles between the two helices is what drives the change in diameter of the sweep.
223
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 224
Building Intelligence into Your Parts
FIGURE 7.16 A 3D sweep
Creating Curve Features Curves in SolidWorks are often used to help define sweeps and lofts, as well as other features. Curves differ from sketches in that curves are defined using sketches or a dialog box, and you cannot manipulate them directly or dimension them in the same way that you can sketches. Functions that you are accustomed to using with sketches often do not work on curves. When you come across a function that does not work using a curve entity, but that works on a sketch (for example, making a tangent spline), then it may help to use the Convert Entities feature. Converting entities on a helix into a 3D sketch creates a spline that lies directly on top of the helix, and allows you to make another spline that is tangent to the new spline.
TIP
The following types of curves can be defined in SolidWorks: n Helix/tapered helix/variable helix/spiral n Projected curve n Curve through XYZ points n Curve through reference points n Composite curve You can find all of the curve functions on the Curves toolbar or through the menus at Insert ➪ Curve.
224
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 225
Choosing a Feature Type
Helix The Helix curve types are all based on a circle in a sketch. The circle represents the starting location and diameter of the helix. Figure 7.17 shows the PropertyManagers of the Constant Pitch and Variable Pitchhelix types.
FIGURE 7.17 The Helix PropertyManager
You can create all of the helical curve types by specifying any combination of total height, pitch, and the number of revolutions. The start angle is best thought of as a relative number. It is difficult to predict where zero degrees starts, and this depends on the relation of the sketch plane to the Origin. The start angle cannot be controlled outside of the PropertyManager, and cannot be driven by sketch geometry. The term pitch refers to the straight-line distance along the axis between the rings of the helix. Pitch for the spiral is different, and is described later.
Tapered Helix The Tapered Helix panel in the Helix PropertyManager enables you to specify a taper angle for the helix. The taper angle does not affect the pitch. If you need to affect both the taper and the pitch, then you can use a variable pitch helix. Figure 7.18 shows how the taper angle relates to the resulting geometry.
225
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 226
Building Intelligence into Your Parts
FIGURE 7.18 The tapered helix
Variable Pitch Helix You can specify the variable pitch helix either in the chart or in the callouts that are shown in Figure 7.19. Both the pitch and the diameter are variable. The diameter number in the first row cannot be changed, but is driven by the sketch. In the chart shown, the transition between 4 and 4.5 revolutions is where the pitch and diameter both change.
FIGURE 7.19 The variable pitch helix
Spiral A spiral is a flattened (planar) tapered helix. The pitch value on a spiral is the radial distance between revolutions of the curve.
Projected curve Many users have difficulty envisioning the concept of the projected curve. The two options available for projected curves are: n Sketch onto Face n Sketch onto Sketch
226
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 227
Choosing a Feature Type
These names can be misleading if you do not already know what they mean. In both cases, the word sketch is used as a noun, not a verb, and so you are not actively sketching on a surface; instead, you are creating a curve by projecting a sketch onto a face.
Sketch Onto Face The Sketch Onto Face option is the easiest to explain, and so I will describe this one first. With this option set, the projected curve is created by projecting a 2D sketch onto a face. The sketch is projected normal (perpendicular) to the sketch plane. This is like extruding the sketch and using the Up To Surface end condition. The sketch can be an open or closed loop, but it may not be multiple open or closed loops, nor can it be self-intersecting. Figure 7.20 shows an example of projecting a sketch onto a face to create a projected curve.
FIGURE 7.20 A projected curve using the Sketch Onto Face option
Sketch Onto Sketch This is the concept that most frequently causes difficulty for users. The Sketch Onto Sketch Projected Curve option can be visualized in a few different ways.
Reverse 2D drawing visualization method One way is to think of it as being the reverse of a 2D drawing. In a 2D drawing, 3D edges (you can think of the edges as curves) are projected onto orthogonal planes to represent the edge from the Front or Top planes. The Sketch Onto Sketch projection takes the two orthogonal views, placed on perpendicular planes, and projects them back to make the 3D edge or curve. This is part of the attraction of the projected curve, because making 3D curves accurately is difficult if you do it directly by using a tool such as a 3D sketch spline; however, if you know what the curve looks like from two different directions, then it becomes easy. Figure 7.21 illustrates this visualization method.
227
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 228
Building Intelligence into Your Parts
When you think of describing a complex 3D curve in space, one of the first methods that usually comes to mind is describing it as a 2D curve from perpendicular directions, exactly in the same way as you would if you created projected drawing views from it. From this, it makes sense to see the creation of the curve as the reverse process, drawing the 2D views first, from which you can then create the 3D curve.
FIGURE 7.21 The reverse 2D drawing visualization method for projected curves
Doing the reverse drawing technique, the curve is built from two views. This is what the curve looks like from this view.
From this view, the curve looks like this.
Intersecting surfaces visualization method A second method used for visualizing Sketch On Sketch projected curves is the intersecting surfaces method. In this method, you can see the curve being created at the intersection of two surfaces that are created by extruding each of the sketches. This method is shown in Figure 7.22.
Curve Through XYZ Points The Curve Through XYZ Points feature enables you to either type in or import a text file with coordinates for points on a curve. The text file can be generated by any program that makes lists of numbers, including Excel. The curve reacts like a spline, and so the teeter-tottering effect may be noticeable, especially because you cannot set end conditions or tangency. To avoid this effect, it may be a good idea to overbuild the curve by a few points on each end. If you import a text file, the file can have an extension of either *.txt or *.sldcrv. The data that it contains must be formatted as three columns of X-, Y-, and Z-coordinates using the document units (inch, mm, and so on), and the coordinates must be separated by comma, space, or tab.
228
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 229
Choosing a Feature Type
Figure 7.23 shows both the Curve File dialog box displaying a table of the curve through X, Y, and Z points, and the *.sldcrv Notepad file. The file can be read from the Curve File dialog box by using the Browse button, but if you manually type the points, then you can also save the data out directly from the dialog box. Just like any type of sketch, this type of curve cannot intersect itself.
FIGURE 7.22 Using intersecting surfaces to visualize a Sketch on Sketch projected curve
Projected curve
Sketch profiles
FIGURE 7.23 The Curve File dialog box showing a table of the curve through X, Y, and Z points, and a Notepad text file with the same information
229
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 230
Building Intelligence into Your Parts
Curve Through Reference Points The Curve Through Reference Points feature creates a curve entity from selected sketch points or vertices. The curve can be an open or closed loop, but a closed loop requires that you select at least three points. You cannot set end conditions of the curve, and so this feature works like a spline in the same way as the XYZ curve. The most common application of this feature is to create a simple two-point curve across the opening of a surface feature to close the opening by using a surface feature such as Fill, Boundary, or Loft.
Composite curve The composite curve joins together multiple curves, edges, or sketches into a single curve entity. The part shown in Figure 7.24 was created by using a composite curve to join together a 3D sketch, variable pitch helix, and a projected curve. You can also use model edges with the composite curve. The curve is shown on half of the part; the rest of the part is mirrored.
FIGURE 7.24 A part created from a composite curve
Split lines Split lines are not exactly curves; they are really just edges that split faces into multiple faces. Split lines are used for several purposes, but are primarily intended to split faces so that draft can be added. They are also used for creating a broken-out face for a color break, or to create an edge for a hold line fillet, which is discussed later in this chapter. There are some limitations to using split lines. First, they must split a face into at least two fully enclosed areas. You cannot have a split line with an open loop sketch where the ends of the loop are on the face that is to be split; they must either hang off the face to be split or be coincident with the edges. Second, nested loops or multiple closed loops are not allowed, nor are self-intersecting
230
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 231
Choosing a Feature Type
sketches. If you need to do something with a sketch of one of these types, then you may be able to accomplish the same thing using multiple split-line features. If you want to create multiple stripes across a face, the best option may be to create an open loop sketch with many S-shaped zigzags. One result of all of these limitations is that it becomes difficult to make split lines using sketch text or other complex sketches. There are several ways of bypassing these limitations, such as copying the surfaces with Knit or Offset at zero distance and then trimming the surface with the sketch, or creating a very shallow solid extrude (although this can be very detrimental to rebuild and graphics speed). A word of caution is needed when using split lines, especially if you plan to add or remove split lines from an existing model. The split lines should go as far down the tree as possible. Split lines change the face IDs of the faces that they split, and often the edges as well. If you roll back and apply a split line before existing features, you may have a significant amount of cleanup to do. Similarly, if you remove a split line that already has several dependent features, then many other features may also be deleted or simply lose their references.
CAUTION
Filleting SolidWorks offers very powerful filleting functions. Many filleting options are available, but most of them are relatively little used or even known. In fact, most users confine themselves to the Constant Radius or Variable Radius fillets. The following section describes all of the available fillet types and options: n Constant Radius Fillet n Multiple Radius Fillet n Round Corners n Keep Edge/Keep Surface n Keep Feature n Variable Radius Fillet n Face Fillet n Curvature Continuous Fillet n Face Fillet with Help Point n Single Hold Line Fillet n Double Hold Line Fillet n Constant Width Fillet n Full Round Fillet n Setback Fillet n Setback Fillet with Variable Radius
231
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 232
Building Intelligence into Your Parts
Figure 7.25 shows the Fillet PropertyManager. There are other options that affect preview and selection of items, and these options are discussed in this section. The Fillet feature comprises various types of functionality. Simple fillets on straight and round edges are handled differently from variable-radius fillets, which are handled differently from the single or double hold line fillet or setback fillets. Once you click the OK button to create a fillet as a certain type, you cannot switch it to another type. You can switch types before the OK button is clicked.
FIGURE 7.25 The Fillet PropertyManager
232
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 233
Choosing a Feature Type
Creating a constant radius fillet Constant radius fillets are the default type that are created if you select only edges, features, or faces without changing any settings. When applying fillets in large numbers, you should consider several best-practice guidelines and other recommendations that come later in this chapter. There are still some long-time users who distinguish between fillets and rounds (where fillets add material and rounds remove it). SolidWorks does not distinguish between the two, and even two edges that are selected for use with the same fillet feature can have opposite functions, for example, both adding and removing material in a single feature.
Selecting entities to fillet You can create fillets from several selections, including edges, faces, features, and loops. Edges offer the most direct method, and are the easiest to control. Figure 7.26 shows how you can use each of these selections to more intelligently create fillets on parts. To select features for filleting, you must select them from the FeatureManager. The Selection Filter only filters edges and faces for fillet selection. You can select loops in two ways, through the RMB Select Loop option, or by selecting a face and Ctrl-selecting an edge on the face.
TIP
Another option for selecting edges in the Fillet command is the Select Through Faces option, which appears on the Fillet Options panel. This option enables you to select edges that are hidden by the model. This can be a useful option on a part with few hidden edges, or a detrimental option on a part where there are many edges due to patterns, ribs, vents, or existing fillets. You can control a similar option globally for features other than fillets at Tools ➪ Options ➪ Display/Selection, Allow Selection In HLR and Shaded Modes.
Faces and Features selections are useful when you are creating fillets where you want the selections to update. In Figure 7.26, the ribs that are intersecting the circular boss are also being filleted. If the rib did not exist when the fillet was applied, but was added later and reordered so that it came before the Fillet feature, then the fillet selection automatically takes the rib into account. If the fillet used edge selection, then this automatic selection updating would not have taken place.
Tangent propagation By default, fillets have the Tangent Propagation option turned on. This is almost always a good choice, although there may be times when you want to experiment with turning it off. Tangent propagation simply means that if you select an edge to fillet, and this edge is tangent to other edges, then the fillet will keep going along tangent edges until it forms a closed loop, the tangent edges stop, or the fillet fails. If you turn off Tangent Propagation, but there are still tangent edges, then you may see different results. One possible result is that it could fail. One of the tricks with fillet features is to try to envision what you are asking the software to do. For example, if one edge is filleted and the next edge is not, then how is the fillet going to end? Figure 7.27 shows two of the potential results when fillets are asked not to propagate, whether or not to tangent edges. The fillet face may continue along its path until it runs off of the part, or until the feature fails.
233
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 234
Building Intelligence into Your Parts
FIGURE 7.26 Selection options for fillets
Select individual edges
Selecting a feature fillets all the edges that touch the feature
234
Selecting a loop is just a shortcut to selecting several edges
Selecting a face fillets all edges around the face
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 235
Choosing a Feature Type
FIGURE 7.27 Turning off the Tangent Propagation option
This may sound counter-intuitive, but sometimes when fillet features fail, it may be useful to turn off propagation and make the fillet in multiple features. There are times when creating two fillets like the one shown in Figure 7.27 will work when making the same geometry as a single feature will not. This may be due to geometry problems where the sharp edges come together and are eliminated by the fillet.
TIP
In general, fillets should be the last features that are applied to a model, particularly the small cosmetic or edge break fillets. Larger fillets that contribute to the structure or overall shape of the part may be applied earlier.
BEST PRACTICE
Be careful of the rock-paper-scissors game that you inevitably get caught up in when modeling plastic parts and deciding on the feature order of fillets, draft, and shell. Most fillets should come after draft, and large fillets should come before the shell. Draft may come either before or after the shell, depending on the needs of the area that you are dealing with on the part. In short, there is no single set of rules that you can consistently apply and that works best in all situations.
235
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 236
Building Intelligence into Your Parts
Dealing with a large number of fillets Figure 7.28 shows a model with a bit of a filleting nightmare. This is a large plastic tray that requires many ribs underneath for strength. Because the ribs may be touched by the user, the sharp edges need to be rounded. Literally hundreds of edges would need to be selected to create the fillets if you do not use an advanced technique.
FIGURE 7.28 A plastic tray with a large number of fillets
Selecting Entities Some of the techniques outlined previously, such as face and feature selection, can be useful for quickly filleting a large number of edges. Another method that still selects a large number of edges, but is not as intuitive as the others, is window selection of the edges. To use this option effectively, you may want to first position the model into a view where only the correct edges will be selected, turn off the Select Through Faces option, and use the Edges Selection filter.
Using Preview I like to use the fillet preview. It helps to see what the fillet will look like, and perhaps more important, the presence of a preview usually means that the fillet will work. Unfortunately, when you have a large number of fillets to create, the preview can cause a significant slowdown. Turning it off or using the Partial Preview are both possible options. Partial Preview shows the fillet on only one edge in the selection, and is much faster when you are creating a large number of fillets. For rebuild speed efficiency, you should make fillets in a minimum number of features. For example, if you have 100 edges to fillet, it is better for performance to do it with a single fillet feature that has 100 edges selected rather than 100 fillet features that have one edge selected. This is the one case where creating the feature and rebuilding the feature are both faster by choosing a particular technique (usually if it is faster to create, it rebuilds more slowly).
PERFORMANCE
236
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 237
Choosing a Feature Type
Although creation and rebuild speed are in sync when you use the minimum number of features to create the maximum number of fillets, this is not usually the case. (There had to be a downside.) When a single feature has a large selection, any one of these edges that fail to fillet will cause the entire feature to fail. As a result, a feature with 100 edges selected is 100 times more likely to fail than a feature with a single edge. Large selection sets are also far more difficult to troubleshoot when they fail than small selection sets that fail.
BEST PRACTICE
Using folders When you have a large number of fillet features, it can be tedious to navigate the FeatureManager. It is therefore useful to place groups of fillets into folders. This makes it easy to suppress or unsuppress all of the fillets in the folder at once. Separate folders can be particularly useful if the fillets have different uses, such as fillets that are used for PhotoWorks models, and fillets that are removed for FEA or drawings.
Multiple Radius Fillet The Multiple Radius Fillet option in the Fillet PropertyManager enables you to make multiple fillet sizes within a single fillet feature. Figure 7.29 shows how the multiple radius Fillet feature looks when you are working with it. You can change values from the callout flags or in the PropertyManager.
FIGURE 7.29 Using the Multiple Radius Fillet option
This may seem like an attractive way to group several fillets into as small a space on the FeatureManager as possible, but I cannot think of a single reason that would drive me to use this option. While there may be a small performance benefit to condensing several features into one, there are many more downsides that adversely affect performance: n Loss of control of feature order n A single failed fillet causes the whole feature, and thus all of the fillets, to fail
237
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 238
Building Intelligence into Your Parts
n Troubleshooting is far more difficult n Smaller groups of fillets cannot be suppressed without suppressing everything n You cannot change the size of a group of fillets together While this may be more personal opinion than best practice, I believe that there are good reasons to consider using techniques other than single features that contain a lot of fillets, or single features that drive fillets of various sizes. Best practice would lean more toward grouping fillets that have a similar use and the same size. For example, you may want to separate fillets that break corners on ribs from fillets that round the outer shape of a large plastic part.
BEST PRACTICE
Another consideration is feature order when it comes to the fillet’s relationship to draft and shell features. If the fillets are all grouped into a single feature, then controlling this relationship becomes impossible.
Round Corners The Round Corners option refers to how SolidWorks handles fillets that go around sharp corners. By default, this setting is off, which leaves fillets around sharp corners looking like mitered picture frames. If you turn this setting on, the corner looks like a marble has rolled around it. Figure 7.30 shows the resulting geometry from both settings.
FIGURE 7.30 The Round Corners option, both on and off
Round corners off
Round corners on
Keep Edge/Keep Surface The Keep Edge/Keep Surface toggle determines what SolidWorks should do if a fillet is too big to fit in an area. The Keep Edge option keeps the edge where it is and tweaks the position (not the radius) of the fillet to make it meet the edge. The Keep Surface option keeps the surfaces of the fillet and the end face clean; however, to do this, it has to tweak the edge. There is often a tradeoff
238
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 239
Choosing a Feature Type
when you try to place fillets into a space that is too small. Sometimes it is useful to try to visualize what you think the result should look like. Figure 7.31 shows how the fillet would look in a perfect world, followed by how the fillet looks when cramped with the Keep Edge option, and how it looks when cramped with the Keep Surface option. The Default option chooses the best option for a particular situation. As a result, it seems to use the Keep Edge option unless it does not work, in which case it changes to the Keep Surface option.
Keep Feature The Keep Feature option appears on the Options panel of the Fillet PropertyManager. By default, this option is turned on. If a fillet completely surrounds a feature such as a hole (as long as it is not a through hole) or a boss, then turning off the Keep Feature option removes the hole or boss. When Keep Feature is on, the faces of the feature trim or extend to match the fillet, as shown in Figure 7.32.
FIGURE 7.31 The Keep Edge option and the Keep Surface option
239
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 240
Building Intelligence into Your Parts
FIGURE 7.32 The Keep Feature option, both on and off
Keep feature off
Keep feature on
Part before fillet
Creating variable radius fillets Variable radius fillets are another powerful weapon in the fight against boring designs; they also double as a useful tool to solve certain problems that arise. Although it is difficult to define exactly when to use the variable radius fillet, you can use it when you need a fillet to round an edge, and it has to change in size to fit the available geometry. It may be easier to identify when not to use a variable radius fillet. Fillets are generally used to round or break edges, not to sculpt a part. If you are using fillets to sculpt blocky parts, unless you are actively trying to make blocky parts with big fillets, then you may consider another approach using complex modeling, which will give the part a better shape and make it more controllable. Other options exist that give you a different type of control, such as the double hold line fillet.
BEST PRACTICE
In some ways, variable radius fillets function like other fillets. For example, they offer propagation to tangent edges and preview options.
240
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 241
Choosing a Feature Type
Applying the values When you first select an edge for the variable radius fillet, the endpoints are identified by callout flags with the value unassigned. A preview does not display until at least one of the points has a radius value in the box. You can also apply radius values in the PropertyManager, but they are easier to keep track of using the callouts. Figure 7.33 shows a variable radius fillet after the edge selection, after one value has been applied, and after three values have been applied. To apply a radius value that is not at the endpoint of an edge, you can select one of the three colored dots along the selected edge. The preview should show you how the fillet will look in wireframe display. By default, the variable radius fillet puts five points on an edge, one at each endpoint, one at the midpoint, and one each halfway between the ends and middle. If you want to create an additional control point, there are three ways to do this: n Ctrl-drag an existing point. n Select the callout of an existing point and change the P (percentage) value. n Change the Number of Instances value in the Variable Radius Parameters panel of the PropertyManager.
FIGURE 7.33 Assigning values to a variable radius fillet
241
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 242
Building Intelligence into Your Parts
If you have selected several edges, and several unassigned values are on the screen, then you can use the Set Unassigned option in the PropertyManager to set them all to the same value. The Set All option sets all radius values to the same number, including any values that you may have changed to be different than the rest. Figure 7.34 shows the Variable Radius Parameters panel.
FIGURE 7.34 The Variable Radius Parameters panel of the Fillet PropertyManager
Another available option with the variable radius fillet is that you can set a value of zero at an end of the fillet. You need to be careful about using a zero radius, because it is likely to cause downstream problems with other fillets, shells, offsets, and even machining operations. You cannot assign a zero radius in the middle of an edge, only at the end. If you need to end a fillet at a particular location, you can use a split line to split the edge and apply a zero radius at that point. Figure 7.35 shows a part with two zero-radius values.
FIGURE 7.35 Zero radius values in the variable radius fillet
242
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 243
Choosing a Feature Type
Straight versus smooth transitions Variable radius fillets have an option for either a straight transition or a smooth transition. This works like the two-profile lofts that were mentioned earlier in this chapter. The names may be somewhat misleading because both transitions are smooth. The straight transition goes in a straight line, from one size to the next, and the smooth transition takes a swooping S-shaped path between the sizes. The difference between these two transitions is demonstrated in Figure 7.36.
FIGURE 7.36 Straight versus smooth transitions of a variable radius fillet
Straight transition Smooth transition
Other reasons to use the variable radius fillet Variable radius fillets use a different method to create the fillet geometry than the default constant radius fillet. Sometimes using a variable radius fillet can make a difference where a constant radius fillet does not work. This is sometimes true even when the variable radius fillet uses constant radius values. It is just another tool in the toolbox.
Face fillet Face fillets may be the most flexible type of fillet because of the range of what they can do. Face fillets start as simply an alternate selection technique for a constant radius fillet and extend to the extremely flexible double hold line face fillet, which is more of a blend than a fillet. Under normal circumstances, the default fillet type uses the selection of an edge to create the fillet. An edge is used because it represents the intersection between two faces. However, there can sometimes be a problem with the edge not being clean, or being broken up into smaller pieces, or any number of other reasons causing a constant radius fillet using an edge selection to fail. In cases like this, SolidWorks displays the error message, “Failed to create fillet. Please check the input geometry and radius values or try using the ‘Face Fillet’ option.”
243
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 244
Building Intelligence into Your Parts
Users almost universally ignore these messages. In the situation shown in Figure 7.37, the Face Fillet option suggested in the error message is exactly the one that you should use. Here the face fillet covers over all of the junk on the edge that prevents the fillet from executing.
FIGURE 7.37 A face fillet covering a bad corner
Face fillets are sometimes amazing at covering over a mess of geometry that you might think you could never fillet. The main limitation on fillets of this type is that the fillet must be big enough to bridge the gap. That’s right, I said big enough. Face fillets can fail if they are either too small or too large. Figure 7.38 shows a complex fillet situation that is completely covered by a face fillet.
FIGURE 7.38 A face fillet covering complex geometry
244
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 245
Choosing a Feature Type
ON the CD-ROM
The model used for this image can be found on the CD-ROM, with the filename Chapter 7 Plastic Cover Fillets.sldprt.
Continuous curvature face fillets Curvature continuity refers to the quality of a transition between two curves or faces, where the curvature is the same or continuous at and around the transition. The best way to convey this concept is with simple 2D sketch elements. When a line transitions to an arc, you have noncontinuous curvature. The line has no curvature, and there is an abrupt change because the arc has a specific radius.
NOTE
Radius is the inverse of curvature, and so r = 1/c. For a straight line, r = ∞, in which case c = 0.
In order to make the transition from r = ∞ to r = 2 smoothly, you would need to use a variable radius arc if such a thing existed. There are several types of sketch geometry that have variable curvature, such as ellipses, parabolas, and splines. Ellipses and parabolas follow specific mathematical formulas to create the shape, but the spline is a general curve that can take on any shape that you want, and its curvature can be controlled to change smoothly or continuously. Splines, by their very definition, have continuous curvature within the spline, although you cannot control the specific curvature or radius values directly. All of this means that continuous curvature face fillets use a spline-based variable-radius section for the fillet, rather than an arc-based constant radius. Figure 7.39 illustrates the difference between continuous curvature and constant curvature. The spikes on top of the curves represent the curvature (1/r, and so the smaller the radius, the taller the spike). These spikes are called a curvature comb.
FIGURE 7.39 Using curvature combs to evaluate transitions
Lines and arc non-continuous curvature
Lines and spline continuous curvature
245
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 246
Building Intelligence into Your Parts
This screen shot was taken in SolidWorks 2007 sp1. The display of the curvature comb in SolidWorks 2006 will have a top curve on the curvature comb. This curve has been removed in the early versions of 2007, but it may be restored in a later service pack.
NOTE
Notice how in Figure 7.39, the curvature comb immediately jumps from no curvature to the constant arc radius, but the spline image ramps up to a curvature that varies.
Face fillets with Help point The Help point in the Face Fillet PropertyManager is a fairly obscure option. However, it is useful in cases where the selection of two faces does not uniquely identify an edge to fillet. For example, Figure 7.40 shows a situation where the selection of two faces could result in either one edge or the other being filleted (normally, I would hope that both edges would be filleted). The fillet will default to one edge or the other, but you can force it to a definite edge using the Help point.
FIGURE 7.40 Using a Help point with a face fillet
Selecting the Help point forces it to the other side Face fillet defaults to the right side
246
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 247
Choosing a Feature Type
In some cases, the Help point is ignored altogether. For example, if you have a simple box, and select both ends of the box as selection set 1, and the top of the box as selection set 2, then the fillet could go to either end. Consequently, assigning a Help point will not do anything in this case, because multiple faces have been selected. The determining factor is which of the multiple faces is selected first. If this were a more commonly used feature, the interface for it might be made a little less cryptic, but because this feature is rarely, if ever, used, it just becomes a quirky piece of trivia.
Single hold line fillet A single hold line fillet is a form of variable radius fillet, but instead of it being defined using the variable radius fillet type, it is created using the face fillet. Rather than the radius being driven by specific numerical values, it is driven by a hold line, or edge, on the model. The hold line can be an existing edge, forcing the fillet right up to the edge of the part, or it can be created by a split line, which enables you to drive the fillet however you like. Figure 7.41 shows these two options, before and after the fillets. Notice that these fillets are still arc-based fillets; if you were to take a cross-section perpendicular to the edge between filleted faces, it would be an arc cross-section with a distinct radius. However, in the other direction, hold line fillets do not necessarily have a constant radius, although they may if the hold line is parallel with the edge between faces.
FIGURE 7.41 Single hold line fillets
Hold line (edge)
Hold line (split line)
You can select the Hold line in the Fillet Options panel of the Face Fillet PropertyManager, as shown in Figure 7.42. The top panel, Fillet Type, is available only when the feature is first created. When you edit it after it has been created, the Fillet Type panel does not appear. As a result, you cannot change from one type of fillet to another after it has been initially created.
247
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 248
Building Intelligence into Your Parts
FIGURE 7.42 The PropertyManager interface for the hold line face fillet
Double hold line fillet There are times when a single hold line does not meet your needs. The single hold line controls only one side of the fillet, and in order to control both sides of the fillet, you must use a double hold line fillet. SolidWorks software does not specifically differentiate between the single and double hold line fillets, but they are radically different in how they create the geometry. When both sides of the fillet are controlled, it is not possible to span between the hold lines with an arc that is tangent to both sides unless you were careful about setting up the hold lines so that they are equidistant from the edge where the faces intersect. This means that the double hold line fillet must use a spline to span between hold lines, as shown in Figure 7.43. To get this feature to work, you need to use the Curvature Continuous option in the Fillet Options panel. Remember that this option creates a spline-based fillet rather than an arc-based fillet, which is exactly what you need for a double hold line fillet. This makes the double hold line fillet more of a blend than a true fillet. Figure 7.44 shows examples of the double hold line fillet.
248
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 249
Choosing a Feature Type
FIGURE 7.43 A double hold line uses a spline, not an arc.
Arc tangent on both ends does not fit both edges
Spline tangent on both ends fits
FIGURE 7.44 Examples of the double hold line fillet
249
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 250
Building Intelligence into Your Parts
Constant width fillet The Constant Width option of the Face Fillet PropertyManager drives a fillet by its width rather than by its radius. This is most helpful on parts where the angle of the faces between which you are filleting is changing dramatically. Figure 7.45 illustrates two situations where this is particularly useful. The setting for constant width is found in the Options panel of the Face Fillet PropertyManager. The part shown in the images is on the CD-ROM, using the filename Chapter 7 Constant Width.SLDPRT.
FIGURE 7.45 The constant width fillet
No fillet
Default face fillet
Face fillet with Constant Width option
Full round fillet The full round fillet is very useful in many situations. In fact, it may actually work in situations where you would not expect it to. It does require quite a bit of effort to accomplish the selection, but it compensates by allowing you to avoid alternate fillet techniques. To create a full round fillet, you have to select three sets of faces. Usually one face in each set is sufficient. The fillet is tangent to all three sets of faces, but the middle set is on the end, and the face is completely eliminated. Figure 7.46 shows several applications of the full round fillet. Notice that it is not limited to faces of a square block, but also propagates around tangent entities and can create a variable radius fillet over irregular lofted geometry.
250
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 251
Choosing a Feature Type
FIGURE 7.46 A full round fillet
Setback fillet The setback fillet is the most complex of the fillet options. You can use the Setback option in conjunction with constant radius, multiple radius, and variable radius fillet types. A setback fillet blends several fillets together at a single vertex, starting the blend at some “setback” distance along each filleted edge from the vertex. At least three, and often more, edges come together at the setback vertex. Figure 7.47 shows the PropertyManager interface and what a finished setback fillet looks like. The following steps demonstrate how to use the setback fillet. Setting up a setback fillet can take some time, especially if you are just learning about this feature. You must specify values for fillet radiuses, select edges and vertices, and specify six setback distances. If you are using multiple radius fillets or variable radius fillets, then this becomes an even larger task. The steps are as follows: 1. Determine the type of fillet to be used:
n Constant radius fillet n Multiple radius fillet n Variable radius fillet
251
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 252
Building Intelligence into Your Parts
FIGURE 7.47 The Setback Fillet Interface and a finished fillet
Setback vertices: all edges coming to these vertices will be filleted
2. Select the edges to be filleted. Selected edges must all touch one of the setback vertices that will be selected in a later step. 3. Assign radius values for the filleted items. Figure 7.48 shows a sample part that illustrates this step.
FIGURE 7.48 The setback fillet setup for steps 1 through 3
4. Select the setback vertices. In the Setback Parameters panel of the PropertyManager, with the second box down highlighted, select the vertices. Although this box looks like it is only big enough for a single selection, it can accept multiple selections.
252
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 253
Choosing a Feature Type
5. Enter setback values. As shown in Figure 7.49, the setback callout flags have leaders that point from a specific value to a specific edge. The dimensions refer to distances, as shown in the image to the right in Figure 7.49. The setback distance is the distance over which the fillet will blend from the corner to the fillet.
FIGURE 7.49 Entering setback values
setback = 3
setback = 4.5
setback = 1.5
253
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 254
Building Intelligence into Your Parts
When you select multiple vertices, the preview arrows that indicate which edge you are currently setting the setback value for may be incorrect. The arrows can only be shown on one vertex, and so you may want to rely on the leaders from the callouts to determine which setback distance you are currently setting.
CAUTION
6. Repeat the process for all selected setback vertices. If you are using a preview, then you may notice that the preview goes away when starting a second set of setback values. Don’t worry. This is probably not because the feature is going to fail. Once you finish typing the values, the preview will return. When you have spent as much time setting up a feature as you will spend on this, seeing the preview disappear can be frustrating; however, persevere, and it will return.
Selecting a Specialty Feature SolidWorks contains several specialty features that perform tasks that you will use less often. Although you will not use these features as frequently as others, you should still at least be aware of them and what they do, because you never know when you will need them.
Dome and Shape The Dome and Shape features are similar in many ways. For example, they both bulge or indent a single selected face. Neither of these features really offers you much control over the actual shape; instead, the shape is controlled by the following: n The shape of the selected face n An internal algorithm n Various settings n A constraint sketch While each of these elements influences the shape of the feature, this influence is not predictable or controllable — it is more of a random or approximate affect. When SolidWorks first released the Shape feature, they advertised it as a complex shape-creation tool. In fairness, it does create complex shapes, but they are not truly intentional, predictable, or controllable, and are certainly not anything that you would use on a consumer product. Dome and Shape are quick approximations, and rarely achieve professional-looking results. Dome and Shape features are best used when you are looking for a generic bulge or indentation, and are not too concerned about controlling the specific shape. Occasionally, one of these features may be exactly what you need, but when you need more precise, predictable control, then you should use the Loft feature. Of these two features, Dome is the most useful.
BEST PRACTICE
254
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 255
Choosing a Feature Type
Because there are more similarities than differences between the Dome and Shape features, the differences are listed first to distinguish them: n The Dome feature can create multiple domes on multiple selected faces in a single feature, although it creates only a single dome for each face. Shape can shape only a single face for each command. n Using the Elliptical Dome setting, Dome can create a feature that is tangent to the vertical. Shape is always tangent to the face that you have selected to create it. n Shape has controls named Pressure, Bend, and Stretch, implying that you should visualize its function as an elastic membrane with positive or negative fluid pressure that causes it to bulge or collapse inward. The similarities between the features include the following: n Both features can use constraint sketches to limit their shape. n Both features work on non-planar faces. n Neither feature can establish a tangent relationship to faces bordering the selected face. n Neither feature can span multiple faces. n Both features display a temporary untrimmed four-sided patch that extends beyond the selected face when you use them on a non-four-sided face. n Both features function on solids. n Neither feature functions on surfaces. The Dome and Shape interfaces are shown in Figure 7.50. Notice that the Shape feature is not integrated into the PropertyManager. This is always a sign of a feature that is not used often. As is the case with a rarely used feature that is not very useful, the feature may disappear rather than be updated. The Dome feature has two notable settings, the elliptical dome and continuous dome. The elliptical dome is available only on flat faces where the boundary is either a complete circle or an ellipse. The cross-section of the dome is elliptical, and does not account for draft, which means that it is always tangent to the perpendicular from the selected flat face. The continuous dome is a setting for any non-circular or elliptical face, including polygons and closed-loop splines. The setting results in a single unbroken face. If you turn the continuous dome setting off, it functions like the elliptical dome setting. Figure 7.51 shows the most useful settings for the Dome feature.
255
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 256
Building Intelligence into Your Parts
FIGURE 7.50 Dome and Shape interfaces
FIGURE 7.51 Settings for the Dome feature
Non-continuous dome Elliptical dome Continuous dome
256
Non-elliptical dome
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 257
Choosing a Feature Type
Wrap feature The Wrap feature enables you to wrap 2D sketches around cylindrical and conical faces. However, trying to wrap around 360 degrees can cause some difficulties. Although all of the available information on the Wrap feature says that you can wrap onto a conical surface, it fails to mention that the point of the cone must be cut off in order for it to work. The Wrap feature works by flattening the face, relating the sketch to the flat pattern of the face, and then mapping the face boundaries and sketch back onto the 3D face. The reason why it is limited to cylindrical and conical faces is that these types of geometry are developable. This means that the faces can be mapped to the flat pattern through some relatively simple techniques that happen behind the scenes. Developable geometry can be flattened without stretching. You will see in a later chapter that sheet metal functions are limited in the same way and for the same reasons. SolidWorks does not wrap onto other types of surfaces, such as spherical, toroidal, or general NURBS surfaces, because you cannot flatten these shapes without distorting or stretching the material. There is software that can flatten these shapes, but it is typically done for sheet-metal deep drawing applications, which highly deform the metal. The Wrap feature has three main options: n Emboss n Deboss n Scribe Figure 7.52 shows the Wrap PropertyManager interface.
FIGURE 7.52 The Wrap PropertyManager interface
257
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 258
Building Intelligence into Your Parts
Scribe Scribe is the simplest of the options to explain, and understanding it can help you understand the other options. Scribe creates a split line-like edge on the face. Several requirements must be met in order to make a wrap feature work: n A cylindrical or conical face. n A closed loop or nested closed loop 2D sketch. n The sketch must be on a plane that is either tangent to or parallel to another plane that is tangent to the face. n The wrap should not be self-intersecting when it wraps around the part (self-intersection will not cause the feature to fail, but on the other types, Emboss and Deboss, it may produce unexpected results). Scribes can be created on solid or surface faces. Scribed surfaces are frequently thickened to create a boss or a cut.
Emboss The Wrap Emboss option works much like the scribe, but it adds material inside the closed loop sketch, at the thickness that you specify in the Emboss PropertyManager. Embossing can only be done on solid geometry. If the feature self-intersects, then the intersecting area is simply not embossed, and is left at the level of the original face. One result is that creating a full wrap-around feature, such as the geometry for a barrel cam, requires a secondary feature. This is because the Wrap feature always leaves a gap, regardless of whether the sketch to be wrapped is under or over the diameter-multiplied-by-pi length.
TIP
To work around this problem, you can use a loft, extrude, or revolve feature to span the gap.
When you use the Emboss option, you can set up the direction of pull and assign draft so that the feature can be injection molded. This limits the size of the emboss so that it must not wrap more than 180 degrees around the part.
Deboss Deboss is just like emboss, except that it removes material instead of adding it. Figure 7.53 demonstrates all of these options. The part shown in the images is available on the CD-ROM with the filename Chapter 7 Wrap.sldprt. For each of the demonstrated cases, the original flat sketch is shown to give you some idea of how the sketch relates to the finished geometry.
258
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 259
Choosing a Feature Type
FIGURE 7.53 The Wrap Feature options
Sketch Scribed edge
Scribed surface feature thickened into a solid and patterned
Embossed barrel cam Closed loop cam profile sketch
Keep in mind that this feature is not like the projected sketch. A projected sketch is not foreshortened on the curved surface, but is projected normal from the sketch plane. A sketch that is one inch long will measure one inch along the curvature of the surface, and will measure less than one inch linearly from end to end.
259
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 260
Building Intelligence into Your Parts
The scribed part in the figure above was created on a conical surface body. The surface was then thickened as a separate body and patterned.
CROSS-REF
Chapter 26 covers working with multiple bodies, and Chapter 27 covers surfaces.
The embossed cam employed a workaround with a revolve feature to close the gap that is always created when wrapping all the way around a part. The example with the debossed text employs a direction of pull and draft so that the geometry can be molded.
Flex The Flex feature is different from most other features in SolidWorks. Most other features create new geometry, but Flex (and Deform, which follows) takes existing geometry and changes its shape. Flex can affect the entire part, or just a portion of it. Flex works on both solid and surface bodies, as well as imported and native geometry. Figure 7.54 shows the Flex PropertyManager interface. Flex has four main options, and many settings. The four main options are as follows: n Bending: Establish two trim planes to denote the ends of the bent area, and specify an angle or radius for the bend. n Twisting: Establish two trim planes to limit the area of the twist, and enter the number of degrees through which to twist. n Tapering: Establish two trim planes to limit the area of the taper. The body will be larger toward one end and smaller toward the other end. n Stretching: Establish two trim planes to limit the area to be stretched. You can stretch the entire body by moving the trim planes outside of the body. Flex is not the kind of feature that you should use to actually design parts, but it can be extremely valuable when you need to show a part in an “in use” state. A simple example would be a rubber strap that stretches over something when it is used, but that is designed and manufactured in its free state. The geometry that you can create by using the flex functions is not generally production-model quality, but it is usually adequate for a looks-like model.
BEST PRACTICE
Figure 7.55 shows examples of each flex option using a model of a rubber grommet. The part shown in the figure can be found on the CD-ROM with the filename Chapter 7 Flex.sldprt. In some cases, the triad and trim planes are slightly disoriented. The best thing to do in situations like this is to simply reorient the triad using the angle numbers in the Triad panel of the PropertyManager. This is also a solution if the planes are turned in such a way that the axis of bending is not oriented to the bend that the part requires.
260
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 261
Choosing a Feature Type
FIGURE 7.54 The Flex PropertyManager interface
The Flex feature is very conscious of separate bodies. In some cases this can be helpful, but in default situations when there is only one body in the part, it can be annoying. Remember to select the body to be affected in the very first selection box at the top of the PropertyManager. If you want to bend only one of the tabs on the grommet, then the best solution is to split the single body into two bodies, and flex only one of the bodies. The examples shown for twisting and stretching use this technique.
TIP
CROSS-REF
Splitting a single body into multiple bodies is covered in Chapter 26.
261
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 262
Building Intelligence into Your Parts
FIGURE 7.55 A rubber grommet in various flex states
Twisting
Bending
Natural position
Stretching Notice bodies have been split
You can place the trim planes by selecting a model vertex, by dragging the arrow on the plane, or by typing in a number. Be careful when dragging the plane arrows because dragging the border of the plane drags the flex value for the feature. (Dragging the plane in a bending operation is like changing the angle or radius for the bend.)
262
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 263
Choosing a Feature Type
Using the triad can be very tricky. Moving the triad in the bending option moves the axis of the bend, and so it determines whether the bend will compress or stretch the material. The position of the triad also determines which side of the bent body will move or stay stationary, or if both sides will move. Placing the triad directly on a trim plane causes the material outside the bend on that side of the trim plane to remain stationary. I highly recommend taking a look at the models that are provided with this chapter to examine the various functions of the Flex feature more carefully. The model uses configurations, which are covered in Chapter 10.
Deform Like the Flex feature, Deform changes the shape of the entire model without regard to parametrics, features, history, or dimensions. Some software packages call this technique global shape modeling. Also like Flex, Deform works on surface bodies as well as solids. Deform can also handle imported geometry as well as SolidWorks native parts. Model complexity is not an issue unless the part runs into itself during deformation. The Deform feature is also another feature type that you may not use to actually design anything, but that you may use to show a model in a deformed state. Typically, if you want a model to have a certain shape, then you need to intentionally and precisely model it with that shape. The problem with using deform and flex geometry for actual design data is that they both create fairly approximate geometry, and this process yields a result that is not completely intentional. The shape that you finally achieve is the result of arbitrary uncontrolled function of the feature, not necessarily creating a shape that you had clearly envisioned beforehand.
BEST PRACTICE
Deform has three types: n Point: Deforms a portion of the model by pushing a point and the geometry around it. n Curve to Curve: The most precise and useful deform type. Select an existing edge and force the edge to match a curve. n Surface Push: This type of deform, while conceptually a very interesting function, is nearly unusable in practice. The part is deformed into a shape vaguely resembling an intermediate shape between the existing state of the part and a “tool” body. Figure 7.56 shows the PropertyManager interface for the Deform feature. The interface is different for each of the three main types, and also changes, depending on selections within the individual types. The interface shown is for the curve to curve type because I believe this to be the most useful type.
263
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 264
Building Intelligence into Your Parts
FIGURE 7.56 The PropertyManager interface for the curve to curve deform
Point Deform The Point Deform option enables you to push a point on the model, and the model deforms as if it were rubber. Figure 7.57 shows the PropertyManager, as well as a before-and-after example of the Point Deform function. The key to using this feature is to ensure that the Deform Region option is turned off. Aside from that, you just have to use trial and error when applying the Deform option. The depth, diameter, and shape of the deformation are not very precise. Also, you cannot specify the precise location for the point to be deformed. Again, this is best used for “looks-like” models, and not production data.
264
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 265
Choosing a Feature Type
FIGURE 7.57 The Deform Point PropertyManager, and a before-and-after example
In the model from Figure 7.57, two Point Deform features are used, one to apply some shape to the back and one to apply some shape to the seat.
Curve to Curve Deform Because this option uses curve (or sketch or edge) data, it is a more precise method than the other deform types. The main concept here is to transform a curve on the original model to a new curve, thus deforming the body to achieve the new geometry. The model shown in Figure 7.58 has been created using the curve to curve deform. The part starts as a simple sweep (sweep an arc along an arc), and then a split line is created to limit the deform to a specific area of the model. The model is on the CD-ROM with the filename Chapter 7 Deform Curve to Curve.sldprt.
Surface Push Deform I do not go into much detail on the Surface Push Deform type because it is not one of the more useful functions in SolidWorks. In order to use it, you must have the body of the part that you are modeling, and a tool body that will be used to shape the part that you are modeling. The finished shape does not fit the tool body directly, but looks about half-way between the model and the tool body, blended together in an abstract sort of way. It looks like the dent that would result from an object being thrown very hard at a car fender, in that neither the thrown part nor the fender are immediately recognizable from the result.
265
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 266
Building Intelligence into Your Parts
FIGURE 7.58 Using the curve to curve deform option
Indent The Indent feature is what the Surface Push Deform is trying to be, or should try to be. Indent uses the same ingredients as the Surface Push, but it produces a result that is both intelligible and useful. For example, if you are building a plastic housing around a small electric motor, then the Indent feature shapes the housing and creates a gap between the housing and the motor. Figure 7.59 shows the PropertyManager interface for the Indent feature, as well as a before-andafter shot of the indent.
266
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 267
Choosing a Feature Type
FIGURE 7.59 Using the Indent feature
In this case, the small motor is placed where it needs to be, but there is a wall in the way. Indent is used to create an indentation in the wall using the same wall thickness, and placing a gap of .010 inches around the motor. The motor is brought into the wall part using the Insert ➪ Part command. This is a multibody technique. Multibodies are examined in detail in Chapter 26.
Tutorial: Bracket Casting When you follow this tutorial, you are encouraged to follow the directions the first time to make sure that you understand the concepts involved, and then to go through it again, this time deviating from the instructions to see if you can expand your understanding by experimentation. To try bracket casting, follow these steps: 1. Open a new part using an inch-based template. 2. On the Right plane, draw a circle centered at the origin with a diameter of .150 inches, and a second circle placed 4.000 inches vertically from the first, with a diameter of 2.250 inches. 3. Extrude the sketch 1.000 inch using a From condition of Offset by 1.000 inch, such that the offset and the extrude depth are in the same direction. Rename this feature Bosses in the FeatureManager. Figure 7.60 shows the results of these steps.
267
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 268
Building Intelligence into Your Parts
FIGURE 7.60 The results of steps 1 to 3
These steps produce multiple bodies that will be merged in a later step. Multiple-body parts are covered in more detail in Chapter 26. You can tell that there are multiple bodies by looking at the Solid Bodies folder near the top of the tree, and expanding the folder. The bodies are listed in the folder.
NOTE
4. On the Top plane, open a new sketch and draw a horizontal construction line across the cylinder, from the midpoint of one side to the midpoint of the other side. To pick up the automatic relations for the midpoints more easily, it is recommended that you orient the view, normal to the sketch, or use the Top view. It does not matter if you make the relations to the top or bottom cylinder, because the midpoints of the sides are in the same place when they are projected into the sketch plane. 5. Next, draw an ellipse (Tools ➪ Sketch Tools ➪ Ellipse) centered at the midpoint of the construction line and that measures .700 inches horizontally and 1.375 inches vertically. Exit the sketch. 6. Show the sketch for the Bosses feature (click the plus icon next to the Bosses extrude to show the sketch, and then RMB click the sketch and select Show). 7. Create a plane parallel to the Top plane at the center of the larger circle. You can access the Plane creation interface at Insert ➪ Reference Geometry ➪ Plane. If you select the Top plane from the flyout FeatureManager and the center of the larger sketch circle from the graphics window, then the interface will automatically select the Parallel Plane At Point option. Click OK to create the plane. Rename this plane Top Boss Plane. 8. Draw a second ellipse on the Top Boss Plane. Do not draw a construction line as you did for the first ellipse; instead, you can just make the center point of the second ellipse directly on top of the first ellipse’s center point. The dimensions should be 1.000 inch horizontal by 1.750 inches vertical. Figure 7.61 shows the results up to this point.
268
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 269
Choosing a Feature Type
FIGURE 7.61 The results up to step 8
When you are sketching on parallel planes that are separated by some distance and trying to pick up automatic relations, it is often very helpful to be looking “normal to” the sketch, so that you can see how other entities are projected into the sketch plane.
TIP
9. Use the Loft feature to loft between the two ellipses. Be sure to select the ellipses in approximately the same location so that they do not twist. If the loft preview accidentally twists, then use the connectors (light-blue square dots on the sketches that are connected by a straight line) to straighten out the loft. Notice that this feature joined together the other two disjoint bodies with the body that was created by the loft into a single body. This is a result of selecting the Merge Result option in the Options panel.
NOTE
TIP
If you want to experiment, expand the Start/End Constraints panel and apply end conditions for the loft. This causes the loft to change from a straight loft to a curved loft.
10. RMB click all sketches that are showing, and select Hide. Do the same for the Top Boss Plane. This cleans up the display to prevent it from becoming confusing. However, if you prefer to see the sketches, then you can leave them displayed. You can either hide or show different types of entities in groups by using the View menu. Hide All Types hides everything, and disables the options for individual entity types to be used.
TIP
11. Open a sketch on the Right plane. Sketch an ellipse such that the center is oriented 1.750 inches vertically from the Origin, and the ellipse measures .750 inches horizontally and 1.500 inches vertically. 12. Extrude this ellipse using the Up To Next end condition. If Up To Next does not appear in the list, then change the direction of the extrude and try it again. 13. Show the sketch of the Bosses feature and open a sketch on the Right plane. Sketch two circles that are concentric with the original circles, with the dimensions of .875 inches and 1.250 inches.
269
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 270
Building Intelligence into Your Parts
14. Create an extruded cut that goes Through All using the End Conditions options. If you get an error, then try reversing the direction of the extrude. Figure 7.62 shows the state of the model up to this step.
FIGURE 7.62 The results up to step 14
15. Start a fillet feature, and select the face of the Loft feature. Assign a radius of .200 inches.
NOTE
Although this fillet is created by selecting a face, it is not a face fillet. Selecting a face for a regular constant radius fillet simply fillets any edge that is on the face.
16. Create a mirror feature, using the Right plane as the mirror plane. In the Mirror PropertyManager, expand the Bodies To Mirror panel, and select anywhere on the part. Make sure that the Merge Solids option is selected. Click OK to accept the mirror. 17. Orient the view to the Front view, and then turn the view on its side (hold down Alt and press the left- or right-arrow key six times). 18. Open a new sketch on the Front plane. From the View menu, make sure that Hide All Types is not on, and show Temporary Axes. Draw and dimension a horizontal construction line, as shown in Figure 7.63. 19. With the construction line selected, start the Sketch Text command (Tools ➪ Sketch Entities ➪ Text). Make sure that the line appears in the Curves selection box. 20. Click in the text box, and type Made in USA (or your name or company name). Select the text and click the Bold button. Deselect the Use Document Font option, change the font to use units, and set the height to .175 inches. 21. Click OK to exit the Sketch Text PropertyManager, and click OK again to exit the sketch. You can turn off the Temporary Axis display.
270
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 271
Choosing a Feature Type
FIGURE 7.63 The results up to step 18
22. Click Insert ➪ Features ➪ Wrap. You should be prompted to select a plane or a sketch. Use the Flyout FeatureManager to select the sketch that you just created with the sketch text in it. Next, select the cylindrical face of the boss to see a preview of the text wrapped onto the face. If the text appears backwards, then click the Reverse Direction option in the Wrap PropertyManager. 23. Select the Emboss option, and assign a thickness of .025 inches. Click in the Pull Direction selection box and select the Front plane. Click OK to accept the feature. 24. Save the part and close it. If you would like to examine a reference part, you can find it on the CD-ROM with the filename Chapter 7 Tutorial Bracket Casting.sldprt. The finished part is shown in Figure 7.64.
FIGURE 7.64 The finished part
271
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 272
Building Intelligence into Your Parts
Tutorial: Creating a Wire-Formed Part Follow these steps to create a wire-formed part: 1. Open a new part using an inch-based template. 2. Open a sketch on the Right plane and sketch a circle that is centered on the Origin with a diameter of 1.500 inches. 3. Create a Helix, Constant Pitch, Pitch, and Revolution, where the Pitch = .250 inches, Revolutions = 5.15, and Start Angle = 0. The Helix command is found at Insert ➪ Curve ➪ Helix/Spiral. 4. Create a sketch on the Front plane, as shown in Figure 7.65. Pay careful attention when adding the construction line, as shown. This line is used in the next step to reference the end of the arc.
FIGURE 7.65 The results up to step 4
5. Open a sketch on the Right plane and use Figure 7.66 to add the correct relations and dimensions. Be aware that the two sketches shown are on different sketch planes, which makes it difficult to depict in 2D. You can also open the part from the CD-ROM for reference. 6. Exit the sketch and create a projected curve. The Projected Curve function is found at Insert ➪ Curve ➪ Projected Curve. Use the Sketch on Sketch option. 7. Open a 3D sketch. You can access a 3D sketch from the Insert menu. Select the helix and click Convert Entities on the Sketch toolbar. Then select the projected curve and click Convert Entities again. You now have two sections of a 3D sketch that are unconnected in space.
272
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 273
Choosing a Feature Type
FIGURE 7.66 The sketch for step 5
Vertical relation
Coincident Dimension references end of construction line
8. Draw a two-point spline to join the ends of the 3D sketch entities that are closest to one another. Assign tangent relations to the ends to make the transition smooth. Figure 7.67 illustrates what the model should look like at this point.
FIGURE 7.67 The results up to step 8
Connecting spline Adjust the length of this handle
273
7
13_080139 ch07.qxp
Part II
3/26/07
3:37 PM
Page 274
Building Intelligence into Your Parts
TIP
You may have to adjust the length of one of the spline tangency length arrows to keep the spline from remaining inside the cylinder of the helix.
9. Open a sketch on the Right plane, and draw an arc that is centered on the Origin and coincident with the end of the 3D sketch helix. The 185-degree angle is created by activating the dimension tool and clicking first the center of the arc, and then the two endpoints of the arc. Now place the dimension. This type of dimensioning allows you to get an angle dimension without dimensioning to angled lines. Exit the sketch. 10. Create a Composite Curve (Insert ➪ Curve ➪ Composite) consisting of the 3D sketch and the new 2D sketch. 11. Create a new plane using the Normal to Curve option, selecting one end of the composite curve. 12. On the new plane, draw a circle that is centered on the end of the curve with a diameter of .120 inches. You need to create a Pierce relation between the center of the circle and the composite curve. 13. Create a sweep feature using the circle as the profile and the composite curve as the path. To create the sweep, you must first exit the sketch. 14. Hide any curves that still display. 15. Click Insert ➪ Cut ➪ With Surface. From the Flyout FeatureManager, select the Right plane. Make sure that the arrow is pointing to the side of the plane with the least amount of material. Click OK to accept the cut. The finished part is shown in Figure 7.68.
FIGURE 7.68 The finished part
274
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 275
Choosing a Feature Type
Summary SolidWorks has a wide range of feature types to choose from, ranging from simple extrudes and revolves to more complex lofts and sweeps. It also offers a range of specialty features that may not be useful on a day-to-day basis, but that have their place in the modeling techniques that you need to know to get the job done. Some features, such as extrude, fillet, and flex, have so many options that it may be difficult to take them all in at once. You should browse through the models on the CD-ROM for this chapter and use the Rollback bar (described in detail in Chapter 11) to examine how the parts were built. You can then try to create a few on your own.
275
7
13_080139 ch07.qxp
3/26/07
3:37 PM
Page 276
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 277
Patterning and Mirroring
P
atterning and mirroring in SolidWorks are great tools to help you improve your efficiency. The software provides many pattern types that also help you accomplish design tasks easily. In addition to the different types of patterns, there are many more detailed options that enable functionality that you may not have considered. A solid understanding of patterning and mirroring tools is necessary to be able to build the maximum amount of parametric intelligence into your models.
IN THIS CHAPTER Patterning in a sketch Mirroring in a sketch Geometry pattern Patterning bodies Patterning faces
Patterning in a Sketch
Patterning fillets
You can use both pattern and mirror functions in Sketch mode, although sketch patterns are not a preferred choice. The distinction between patterning and mirroring in Sketch mode is important when it comes to sketch performance. there are many metrics for how software performs, PERFORMANCE Although in SolidWorks, the word performance means the same thing as speed. Sketch patterns have a very adverse effect on speed.
A little test You can hear a lot of conflicting information about which features are better to use in different situations. Users coming from a 2D background often prefer to use functions such as sketch patterning because it looks familiar, without questioning whether there is a better way. When in doubt, you can perform a test to determine for yourself which is better.
277
Understanding pattern types Mirroring in 3D Tutorial: Creating a circular pattern Tutorial: Mirroring features
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 278
Building Intelligence into Your Parts
In this test, I made a series of 20-by-20 patterns using circles, squares, and hexagons. The patterns were both sketch patterns and feature patterns, and were created with both Verification On Rebuild and Geometry Pattern turned on and off. Verification On Rebuild is a setting that you can access through Tools ➪ Options ➪ Performance ➪ and Geometry Pattern is a setting that is applicable only to feature patterns. Table 8.1 shows the rebuild times (in seconds) of certain types of patterns as measured by Feature Statistics (found at Tools ➪ Feature Statistics). Sketch patterns are far slower than feature patterns, by a factor of about ten. The biggest speed reduction occurs when you use sketch patterns in conjunction with the Verification on Rebuild setting, especially as the number of sketch entities being patterned increases. Generally, the number of faces being patterned has a significant effect on the speed of the pattern. The sketch pattern times are taken for the entire finished model, including the sketch pattern and a single extrude feature, using the sketch with the pattern to do an extruded cut. The sample parts are on the CD-ROM for reference. Look for the filenames beginning “Reference1” through “Reference7.”
TABLE 8.1
Pattern Rebuild Times Pattern Type
Default
Geometry Pattern
Verification on Rebuild
20x20 sketch circle
1.75
n/a
10.5
20x20 sketch square
10.8
n/a
143
20x20 sketch hex
19.4
n/a
294
20x20 feature circle
.19
.28
.19
20x20 feature square
.34
.55
.33
20x20 feature hex
.48
.70
.48
Figure 8.1 shows one of the parts used for this simple test.
Patterning a sketch It is best to pre-select the sketch entities that you want to pattern before using the Sketch Pattern tool. If you do not pre-select, then after the PropertyManager is open, you can only select entities to pattern one by one because the window select is not available for this function.
TIP difficult.
278
When creating a linear sketch pattern, be sure to select the Add Dimension check boxes. If these dimensions are not added, then editing the pattern becomes more
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 279
Patterning and Mirroring
FIGURE 8.1 A pattern part used for the test
Linear Sketch Pattern The Linear Pattern PropertyManager is shown in Figure 8.2.
FIGURE 8.2 The Linear Pattern PropertyManager
279
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 280
Building Intelligence into Your Parts
The Direction 1 panel works predictably by establishing the direction and spacing, and then the number. The Angle setting enables you to specify a direction that does not rely on anything outside of the sketch. Direction 2 works a little differently. You must first specify how many instances you want, and then the other information becomes available.
Circular Sketch Pattern The Circular Sketch Pattern defaults to the sketch Origin as the center of the pattern. You can move and position this point using the numbers in the PropertyManager, but you cannot dimension it until after the pattern is created. Again, this is another feature where you need to pre-select because window selection is not available (patterned sketch entities must be selected one by one to go into the Entities to Pattern panel). Figure 8.3 shows the Circular Pattern PropertyManager.
FIGURE 8.3 The Circular Pattern PropertyManager
Mirroring in a Sketch Mirroring in a sketch is a completely different matter from patterning in a sketch. It offers superior performance, and the interface is better developed. Mirrored entities in a sketch are an instrumental part of establishing design intent.
280
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 281
Patterning and Mirroring
Two methods of mirroring items in a sketch are discussed here, along with a method to make entities work as if they have been mirrored when in fact they were manually drawn.
Mirror Entities Mirror Entities works by simply selecting the entities that you want to mirror along with a single centerline, and pressing the Mirror Entities button on the Sketch toolbar. It is a simple and effective tool that you can use on existing geometry. One feature of Mirror Entities may sometimes cause unexpected results. For example, in some situations, Mirror Entities will mirror a line or an arc and merge the new element with the old one across the centerline. This happens in situations when the mirror and the original would form a single line or a single arc. SolidWorks may delete certain relations and dimensions in these situations.
Dynamic Mirror As the name suggests, Dynamic Mirror mirrors sketch entities as they are created. You can activate it by selecting a centerline and clicking the button on the Sketch toolbar. Dynamic Mirror is not on the toolbar by default; you need to select Tools, Customize, Commands to add it to the toolbar. You can also access Dynamic Mirror through the menus at Tools, Sketch Tools, Dynamic Mirror. When you activate this function, the centerline displays with hatch marks on the ends, and remains active until you turn it off or exit the sketch. Figure 8.4 shows the centerline with hatch marks.
FIGURE 8.4 The Dynamic Mirror centerline with hatch marks
281
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 282
Building Intelligence into Your Parts
Symmetry sketch relation The Symmetry sketch relation has been covered in previous chapters on sketching, but it is mentioned here because it offers you a manual way to mirror sketch entities. There are editing situations when you may not want to create new geometry, but instead use existing entities with new relations driving them. To create the Symmetry sketch relation, you must have two similar items (such as lines or endpoints) and a centerline selected.
Geometry Pattern The SolidWorks Help file says that the Geometry Pattern option in feature patterns results in a faster pattern because it does not pattern the parametric relations. This claim is valid only when there is an end condition on the patterned feature such that the feature will actually pattern the end condition’s parametric behavior. The part shown in Figure 8.5 falls into this category. The improved rebuild time goes from .30 to .11 seconds. Although a 60-percent reduction is significant, the most compelling argument for the use of the Geometry pattern is to avoid the effect of patterning the end-condition parametrics.
FIGURE 8.5 A geometry pattern test
Geometry pattern off — Parametrics are patterned
Geometry pattern on — Parametrics not patterned
Under some conditions, Geometry Pattern will not work. One example is any time a patterned face would merge with an unpatterned face. These situations can be difficult to identify. Figure 8.6 shows a pattern that cannot be created using the Geometry Pattern option. The boss merges with the side face of the block, which generates the error message shown in the figure. The circular part shown in the image is an exception where the partial cylindrical bosses merge with the side of the cylinder, but Geometry Pattern works.
282
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 283
Patterning and Mirroring
FIGURE 8.6 Merged faces
Patterning Bodies The topic of multiple bodies is covered in depth in Chapter 26, but it must be dealt with briefly here. Any discussion of patterning is not complete without a discussion of bodies because using bodies is an available option with all of the pattern and mirror types. SolidWorks parts can contain multiple solid bodies. A body is a solid that comprises a single contiguous volume. Surface bodies are defined differently, but they can also be patterned and mirrored as bodies. There are both advantages and disadvantages to mirroring and patterning bodies instead of features. The advantages can include the simplicity of selecting a single body for mirroring or patterning. In cases where the geometry to be patterned is complex or there is a large number of features, patterning bodies also can be much faster. However, in the example used earlier with patterning features in a 20-by-20 grid of holes, when done by patterning a single body of 1" × 1" × .5" with a .5" diameter hole, patterning bodies gives a rebuild time of about 130 seconds with or without Verification On Rebuild. It is the function that combines the resulting bodies into a single body that takes most of the time. This says that for large patterns of simple features, patterning bodies is
283
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 284
Building Intelligence into Your Parts
not an efficient technique. Although I do not have an experiment in this chapter to prove it, I believe that creating a pattern of a smaller number of complex bodies using a large number of features in the patterned body would show a performance improvement over patterning the features. Another disadvantage of patterning or mirroring bodies is that it does not allow you to be selective. You cannot mirror the body minus a couple of features; without doing some shuffling of feature order in the FeatureManager. Another disadvantage is that if the base of the part has already been mirrored by a symmetrical sketch technique, then body mirroring is not going to help you mirror the subsequent features. Also, the Merge Bodies option does not work as you would want it to. It merges only those bodies that are part of the mirror to bodies that are part of the mirror. Pattern Bodies does not even have an option to merge bodies. Both of these functions are often going to require an additional combine (for solid bodies) or knit (for surface bodies) to put the final results together.
CROSS-REF
Bodies are discussed in more detail in Chapter 26. Surface modeling is covered in Chapter 27.
Patterning Faces Most of the pattern types have an option for Pattern Faces. This option has a few restrictions, the main limitation being that all instances of the pattern must be created within the boundaries of the same face as the original. Figure 8.7 shows an example of the Pattern Faces option working with a Circular Pattern feature.
FIGURE 8.7 A circular pattern using the Pattern Faces option
284
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 285
Patterning and Mirroring
To get around this limitation, you can knit and pattern the surface body, as shown in Figure 8.8.
FIGURE 8.8 Patterning a surface body
Split in face means faces from feature on side cannot be patterned all the way around
CROSS-REF
Working with surface bodies is covered in Chapter 27.
Patterning Fillets You may hear people argue that you cannot pattern fillets. This is partially true and partially untrue. It is true that fillets as individual features cannot be patterned. For example, if you have a symmetrical box and a fillet on one edge and want to pattern only the fillet to other edges, this cannot be done. However, when fillets are patterned with their parent geometry, they are a perfectly acceptable candidate for patterning. This is also true for the more complex fillet types, such as variable radius and full radius fillets. You may need to use the Geometry Pattern option, and you may need to select all of the fillets affecting a feature, but it certainly does work.
285
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 286
Building Intelligence into Your Parts
Understanding Pattern Types Up to now, I have discussed patterns in general, differentiated sketch patterns from feature patterns and body patterns, and looked at some other factors that affect patterning and mirroring. I will now discuss each individual type of pattern to give you an idea of what options are available.
Linear Pattern The Linear Pattern feature has several available options: n Single direction or two directions: Directions can be established by edge, sketch entity, axis, or linear dimension. If two directions are used, the directions do not need to be perpendicular to one another. n Spacing: The spacing represents the center-to-center distance between pattern instances, and can be driven by an equation. n Number of Instances: This number represents the total number of features in a pattern, which includes the original seed feature. It can also be driven by an equation. Equations are covered in detail in Chapter 9. n Direction 2: The second direction works just like the first, with the one exception of the Pattern Seed Only option. Figure 8.9 shows the difference between a default twodirection pattern and one using the Pattern Seed Only option.
FIGURE 8.9 Using the default two-direction pattern and the Pattern Seed Only Option
Original feature
Pattern seed only
n Instances to Skip: This option enables you to select instances that you would like to leave out of the final pattern. Pink dots are the instances that remain, and the red dots are the ones that have been removed. Figure 8.10 shows the interface for skipping instances. You may have difficulty distinguishing the red and pink colors on the screen.
286
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 287
Patterning and Mirroring
FIGURE 8.10 Using the Instances to Skip option
n Propagate Visual Properties: This option patterns the color, texture, or cosmetic thread display, along with the feature to which it is attached. n Vary Sketch: This option in patterns is often overlooked and not widely used or understood. While it may have a niche application, it is a powerful option that can save you a lot of time if you ever need to use it. Vary Sketch allows the sketch of the patterned feature to maintain its parametric relations in each instance of the pattern. It is analogous to the Geometry Pattern. Where Geometry Pattern disables the parametric end condition for a feature, Vary Sketch enables the parametric sketch relations for a pattern. To activate the Vary Sketch option, the Linear Pattern must use a linear dimension for its Pattern Direction. The dimension must measure in the direction of the pattern, and adding the spacing for the pattern to the direction dimension must result in a valid feature. The sketch relations must hold for the entire length of the pattern. Figure 8.11 shows the sketch relations and the resulting pattern. The preview function for this feature does not work. To adequately understand how this feature works, open the sample file from the CD-ROM called Chapter 8 Vary Sketch.sldprt, and edit Sketch2. Edit the .40-inch dimension. Double-click it and use the scroll arrow to increase the dimension; watch the effect on the sketch. If a sketch does not do this, then it cannot be used with the Vary Sketch option. In this case, the .40-inch dimension was used as the direction. The direction dimension has to be able to drive the sketch in the same way that this one does. These dimensions cannot pass through the Zero value and cannot flip directions or move into negative values.
287
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 288
Building Intelligence into Your Parts
FIGURE 8.11 Using the Vary Sketch option
To make the sketch react this way to changes in the dimension, the slot was created using the bidirectional offset that was demonstrated in an earlier chapter, which means that the whole operation is being driven by the construction lines and arcs at the centerline of the slot. Sketch points along the model edges are kept at a certain distance from the ends of the slots using the .50-inch dimensions. The arcs are controlled by an Equal Radius relation and a single .58-inch radius dimension. The straight lines at the ends of the slots are controlled by an Equal Length relation. This type of dimensioning and relation creation is really what parametric design is all about. The Vary Sketch option takes what is otherwise a static linear pattern and makes it react parametrically. If you model everything with the level of care that you need to put into a Vary Sketch pattern feature sketch, then your models will react very well to change.
Circular Pattern The Circular Pattern feature requires a straight edge, an axis, or a temporary axis to act as the center of the pattern. All of the other options are the same as the Linear Pattern — except that the Circular Pattern does not have a Direction 2 option, and the Equal Spacing option works differently. Equal Spacing takes the total angle and evenly divides the number of instances into that angle. The name equal spacing is a bit misleading because all Circular Patterns create equal spacing between the instances, but somehow everyone knows what they mean.
288
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 289
Patterning and Mirroring
Without using the Equal Spacing option, the Angle setting represents the angular spacing between instances. The Vary Sketch option is available in Circular Pattern as well. The principles for setup are the same, but you must select an angular dimension for the direction. The part shown in Figure 8.12 was created using this technique.
FIGURE 8.12 A Circular Pattern vary sketch
Curve Driven Pattern A Curve Driven Pattern does just what it sounds like: it drives a pattern along a curve. The curve could be a line, an arc, or a spline. An interesting thing about the Curve Driven Pattern is that it can have a Direction 2, and Direction 2 can also be a curve. This pattern type is one of the most interesting, with many options available. For an entire sketch to be used as a curve, the sketch must not have any sharp corners — all of the entities must be tangent. This could mean using sketch fillets or a fit spline. The example shown in Figure 8.13 is created using sketch fillets. This pattern uses the Equal Spacing option, which spaces the number of instances evenly around the curve. It also uses the Offset Curve option, which maintains the patterned feature’s relationship to the curve throughout the pattern, as if an offset of the curve goes through the centroids of each patterned instance. The Align to Seed option is also used, which keeps all of the pattern instances aligned in the same direction.
289
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 290
Building Intelligence into Your Parts
FIGURE 8.13 The Curve Driven Pattern using sketch fillets
Figure 8.14 shows the same part using the Transform Curve positioning option and Tangent to Curve alignment option. Instead of an offset of the curve going through the centroids of each patterned feature instance, in the Transform Curve, the curve is moved rather than offset. On this particular part, this causes a messy pattern. The Tangent to Curve option gives every patterned instance the same orientation relative to the curve as the original. The Face Normal option is used for a 3D pattern, as shown in Figure 8.15. Although this functionality seems a little obscure, it is useful if you need a 3D curve-driven pattern on a complex surface. If you are curious about this example, it is on the CD-ROM with the filename Reference 3d Curve Driven.sldprt.
290
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 291
Patterning and Mirroring
FIGURE 8.14 Using the Transform Curve and Tangent to Curve options
FIGURE 8.15 Using a 3D curve-driven pattern
291
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 292
Building Intelligence into Your Parts
Using a Direction 2 for a curve-driven pattern will create a result similar to that in Figure 8.16. This is another situation that, although rare, is good to know about.
FIGURE 8.16 Using Direction 2 with a curve-driven pattern
The rest of the Curve Driven Pattern works like the other pattern features that have already been demonstrated.
Sketch Driven Pattern Sketch-driven patterns use a set of sketch points to drive the locations of features. The Hole Wizard drives the locations of multiple holes using sketch points in a similar way. However, the Sketch Driven Pattern does not create a 3D pattern in the same way that the Hole Wizard does. Figure 8.17 shows a pattern of several features that has been patterned using a sketch-driven pattern. A reference point is not necessary for the first feature. The Centroid option in the Reference Point section is fine for symmetrical and other easily definable shapes such as circles and rectangles, where you can find the centroid just by looking at it, but on more complex shapes, you may want to use the Selected Point option. The Selected Point option is shown in Figure 8.18.
292
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 293
Patterning and Mirroring
FIGURE 8.17 Using a sketch-driven pattern
FIGURE 8.18 Using the Selected Point option in a sketch-driven pattern
Selected point corresponds to the sketch points in the pattern
293
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 294
Building Intelligence into Your Parts
Table Driven Pattern A table-driven pattern drives a set of feature locations, most commonly holes, from a table. The table may be imported from any source with two columns of data (X and Y) that are separated by a space, tab, or comma. Extraneous data will cause the import to fail. The X,Y Origin for the table is determined by a Coordinate System reference geometry feature. The XY plane of the Coordinate System is the plane to which the XY data in the table refers. You can access the Coordinate System command through the menus at Insert, Reference Geometry, Coordinate System. You can create the Coordinate System by selecting a combination of a vertex for the Origin and edges to align the axes. Like the Sketch Driven Pattern, this feature can use either the centroid or a selected point on the feature to act as the reference point. The fact that this feature is still in a floating dialog box points to its relatively low usage and priority on the SolidWorks upgrade schedule. The interface for the feature is rather crude in comparison to some of the more high-usage features. This interface is shown in Figure 8.19.
FIGURE 8.19 The Table Driven Pattern dialog box
294
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 295
Patterning and Mirroring
Fill Pattern The Fill Pattern feature fills a face or area enclosed by a sketch with a pattern of a selected feature. The type of pattern used to fill the area is limited to one of four pre-set patterns that are commonly used in gratings and electronics ventilation in plastics and sheet metal. These patterns and other options for the Fill Pattern are shown in Figure 8.20.
FIGURE 8.20 Using the Fill Pattern feature
The Pattern Layout panel enables you to control spacing and other geometrical aspects of the selected pattern layout, as well as the minimum gap from the fill boundary. This is most useful for patterns of regularly spaced features with an irregular boundary.
295
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 296
Building Intelligence into Your Parts
Mirroring in 3D Because symmetry is an important aspect of modeling parts in SolidWorks, mirror functions are a commonly used feature. This is true whether you work on machine design parts, sheet metal, injection-molded, cast, or forged parts. I discussed sketch-mirroring techniques earlier in this chapter, and now I will discuss 3D mirroring techniques.
Mirroring bodies Earlier in this chapter, I discussed patterning bodies. I mentioned that the patterning and mirroring tools in SolidWorks do not have adequate functionality when it comes to body management. Neither tool allows the patterned or mirrored bodies to be merged with the main body if the main body is not being patterned or mirrored. Figure 8.21 shows the Options panels for both the Linear Pattern (on the left) and the Mirror (on the right) features. Here you can see that the pattern function has no provision whatsoever for merging bodies. The Mirror appears to have the functionality, but it applies only to bodies that are used or created by the Mirror feature. In future version of SolidWorks, these features will hopefully be outfitted with more complete merge and feature scope functionality, such as Extrude features.
FIGURE 8.21 Options panels from the Linear Pattern and Mirror PropertyManagers
Mirroring bodies is the fastest and simplest method when a part has complete symmetry. However, this may not be an option if the part is not completely symmetrical. Also, the decision to mirror must often be made when you are creating the first feature. If the first feature is modeled as a sketch that is built symmetrically around the Origin, then you may need to cut the part in half in order to mirror it. This is an adequate modeling technique, although it is not as clean as it could be.
BEST PRACTICE
Mirroring features Features can be mirrored across planes or flat faces used as the plane of symmetry. If you are mirroring many features, then it is best to mirror them all with a single mirror feature rather than to make several mirror features. You may have to do this by moving the mirror feature down the tree as you add new features. If possible, it is better to mirror bodies than features, but you should not go too far out of your way or model in an unnatural, contrived manner in order to make this happen.
296
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 297
Patterning and Mirroring
Mirroring entire parts Often when modeling, you are required to have a left- and a right-handed part. For this, you need to use a method other than body or feature mirroring. The Mirror Part command creates a brand new part, by mirroring an existing part. The new part does not inherit all of the features of the original, and so any changes must be created in the original part. If you want different versions of the two parts, you need to use Configurations, which have not been covered yet in this book.
CROSS-REF
Configurations are covered in detail in Chapter 10.
You can use the Mirror Part command by pre-selecting a plane or planar face. You should be careful when choosing the plane because the new part will have a relationship to the part Origin, based on the plane on which it was mirrored. The Mirror Part command is found in the Insert menu. When mirroring a part, you can bring several entity types from the original file to the mirrored part. These include axes, planes, cosmetic threads, and surface bodies. Sketches and features are two commonly requested items to be brought forward by the Mirror Part command, but this is not possible in the current version of the software.
Tutorial: Creating a Circular Pattern Follow these steps to get practice with creating circular pattern features: 1. Draw a square block on the Top plane centered on the Origin, 4 inches on each side, .5-inch thick extruded Mid Plane with .5-inch chamfers on the four corners. 2. Pre-select the top face of the block and start the Hole Wizard. (Pre-selection avoids a 3D placement sketch.) Select a counterbored hole for a 10-32 socket head cap screw, and place it as shown in Figure 8.22. 3. Create an axis using the Front and Right planes. Click Insert ➪ Reference Geometry ➪ Axis. Select the Two Planes option, and select Front and Right planes from the flyout FeatureManager. (Click the bar that says Axis at the top of the PropertyManager to access the flyout FeatureManager.) This creates an axis in the center of the rectangular part. 4. Click the Circular Pattern tool on the Features toolbar. Select the new Axis in the top Pattern Axis selection box in the Circular Pattern PropertyManager. Select the Equal Spacing option and make sure that the angle is set to 360°. Set the number of instances to 8.
297
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 298
Building Intelligence into Your Parts
FIGURE 8.22 Start drawing a plate with holes.
5. In the Features To Pattern panel, select the counterbored hole. Make sure that Geometry Pattern is turned off. 6. Click OK to finish the part, as shown in Figure 8.23.
FIGURE 8.23 The finished circular pattern
298
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 299
Patterning and Mirroring
Tutorial: Mirroring Features Follow these steps to get some practice with creating mirror features: 1. Open the file from the CD-ROM called Chapter8 Tutorial2.sldprt. 2. Open a sketch on the side of the part, as shown in Figure 8.24. The straight line on top is 1.00 inch long, and the angled line ends 2.70 inches from the edge, as shown.
FIGURE 8.24 The sketch for the Rib feature
3. Click the Rib tool on the Features toolbar or select it from the menu at Insert ➪ Features ➪ Rib. Set the material arrow to go down toward the block, and the thickness setting to go to the inside by .375 inches. The PropertyManager and the preview should look like Figure 8.25.
FIGURE 8.25 Applying the Rib feature
299
8
14_080139 ch08.qxp
Part II
3/26/07
3:39 PM
Page 300
Building Intelligence into Your Parts
4. Create a linear pattern using the rib, making it go 2 inches into the part. 5. Create a chamfer on the same side of the part as the original rib, as shown in Figure 8.26. The chamfer is an Angle-Distance using 60° and .5 inches. 6. Create a round hole, sized and positioned as shown.
FIGURE 8.26 Additional features on the part
7. Mirror the hole and the chamfer about the Right plane. The parametrics of the chamfer will have difficulty patterning, and so you need to use the Geometry Pattern option. The finished part is shown in Figure 8.27.
FIGURE 8.27 The finished part
300
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 301
Patterning and Mirroring
Summary Feature patterns and mirrors are powerful tools, but they require some discipline to benefit from their usefulness. Patterns in particular are extremely flexible, with many types of functions and options available. You should avoid sketch patterns if possible, not only because of performance considerations, but also because complex sketches (sketches with a lot of entities and relations) tend to fail more often than simple sketches.
301
8
14_080139 ch08.qxp
3/26/07
3:39 PM
Page 302
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 303
Using Equations
P
arametric sketch relations are not the only way to drive dimensions with intelligence. You can also use equations, link values, and global variables. Equations help you to create simple or complex mathematical relations between dimensions. Link values are essentially a quick way of making two dimensions equal. Global variables can be used in equations like other dimension names. These three techniques are all very similar and related to one another in the interface, but are used in different ways in different situations. Equations are a very powerful extension of the set of parametric power tools that SolidWorks offers to users. If you are not accustomed to driving dimensions with equations, then you may find it challenging to get the order of equations correct so that dimensions are not changed multiple times when more than a few equations are involved.
Understanding Equations You can find the Equations tool on the Tools toolbar, or through the menus at Tools, Equations. Figure 9.1 shows the Equations main interface along with the Add Equation window. As I have noted with other areas of the interface, Equations still uses a floating dialog box. I would guess that this function is going to be completely revised in the near future, and at least part of this change will involve moving it to the PropertyManager, as is the case with most other commonly used functions.
303
IN THIS CHAPTER Understanding equations Link values Global variables Expressions Tutorial: Equations
15_080139 ch09.qxp
Part II
3/26/07
3:41 PM
Page 304
Building Intelligence into Your Parts
FIGURE 9.1 The Equations interface
Using the Equations interface, you can turn off equations temporarily by deselecting the Active check box in front of the equation. Equations can also be deactivated by a design table. I will discuss design tables in more detail in Chapter 10, which discusses configurations. Although I do not cover configurations until Chapter 10, I will mention this here. Equations and configurations (particularly those that are driven by a design table) should probably not be mixed. This is not because they do not work together, but more for the sake of organization. When controlling dimensions, it can become confusing if the changes are being driven from multiple sources. Also, there is no reason not to bring your equations into Excel rather than using the comparatively limited equation functionality offered by SolidWorks.
BEST PRACTICE
Creating equations Equations are easy to create and useful for many purposes. A common situation where you would use an equation is to space a pattern of holes evenly along an edge, including the gap on both ends, where the gap at the ends is half of the regular spacing. Before you write an equation, you need to take care of a few organizational details.
Naming dimensions It is not necessary to name every entity in every SolidWorks document, but you should get in the habit of naming important features, sketches, and even dimensions. Dimensions become particularly important when you use equations, configurations, and design tables. Under most circumstances, you do not use or even see dimension names, but with equations, you do.
304
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 305
Using Equations
Named dimensions make a huge difference when you want to recognize the function of an equation by simply reading it. A most obvious example would be the difference between D3@Sketch6 and Length@WindowExtrusionSketch. The first name means nothing, but the second one is descriptive if you are familiar with the part. To name a dimension, RMB click the dimension and select Properties. At the top of the dialog box shown in Figure 9.2, type the new name for the dimension in the Name text box. You cannot use the symbol @ in dimension names because it is used as a delimiter between the name of the dimension and the feature or sketch to which it applies.
FIGURE 9.2 Renaming a dimension
You should keep dimension names as short as possible while still making them unique and descriptive. This is because space in the interface is often limited, and when combined with sketch or feature names (and even part names when used in an assembly), the names can become difficult to read.
BEST PRACTICE
TIP
You can show dimension names as a part of the dimension value itself by accessing the setting at Tools, Options, General, Show Dimension Names.
Building the equation When creating an equation in SolidWorks, it is often a good idea to write it out on paper first. Examine the part shown in Figure 9.3, where the relevant dimensions have been named and displayed. The behavior to be driven by the equations is that the number of holes — called Instances here — is the driving variable. From that number, the spacing of the holes is calculated over the length of the part. There is also a gap on each end of the pattern of holes. This gap (measured between the center of the last hole and the end of the part) needs to always be half of the spacing between the holes. The sigma symbols to the left of the dimensions indicate that an equation is driving it. Dimensions driven by equations cannot be directly edited.
305
9
15_080139 ch09.qxp
Part II
3/26/07
3:41 PM
Page 306
Building Intelligence into Your Parts
FIGURE 9.3 Variables for the hole pattern
In this case, more sophistication has not been implemented to account for the diameter of the holes possibly interfering with one another when there are a large number of holes. In other words, because there are two values that need to be calculated (the spacing and the gap), you need to create two equations. Because the gap dimension is always half of the spacing, the spacing needs to be calculated first, as follows: Spacing = Length / ((Instances-1)+1)
The Instances -1 term stands for the number of spacings. If you have two holes, then there is only one spacing. The +1 term stands for the two half-spacings for the two ends. The second equation is simpler and looks like this: Gap = Spacing / 2
The order of the equations is important. SolidWorks solves the equations in the order in which they are listed in the Equations dialog box. Because the gap is dependent on the spacing, the spacing must be calculated before the gap. If it is done the other way around, then you can get into a situation where it takes two rebuilds to finalize a set of equations, or even a situation where in every rebuild, all of the numbers change. This is called a circular relation, and is a common error in order or history dependent functions, not just in SolidWorks, but in any computer application. Figure 9.4 shows the resulting set of equations.
FIGURE 9.4 Equations for the hole pattern
306
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 307
Using Equations
Before beginning to build the equation, you should first display the dimensions that you need to use to create the equation. You can add dimensions to the equation by clicking them from the graphics window. To do this, RMB click the Annotations folder at the top of the FeatureManager, and select Show Feature Dimensions. You should also select the Display Annotations option if it is not already on. When you have done this, all of the dimensions that you need to create every feature are displayed. Also be sure to turn on Tools ➪ Options ➪ General ➪ Show Dimension Names. For models that have more than a few features, showing all of the dimensions in the entire model may overload the screen with information. In this case, you can doubleclick a feature from the FeatureManager to show all of the dimensions on that feature.
TIP
To build the equation, first use the Equation button on the Tools toolbar to open the Equations dialog box. Then press the Add button to display the Add Equation dialog box. To add dimensions to the equation section, just click the dimension. You can use the keypad on the dialog box or on your keyboard to add operators and syntax. All standard rules of syntax apply for the order of operations, use of parentheses, and driving versus driven sides of the equation.
Using comments Notice the comment to the right of the first equation in Figure 9.4. Comments can be very useful for annotating equations for yourself or others. Two important reasons to annotate are to remember the significance of variables or dimensions, and to add special notes about the logic of the equation. You can make comments for equations by using a single quote after the end of the equation, or by using the Comment button in the Add Equation dialog box. In the following example, “Spacing@LPattern1” = “Length@Sketch1” / (“Instances@LPattern1”) ‘This must be solved first
the comment, “This must be solved first,” is applied to the equation using the single quote before the comment. Adding to the earlier discussion about projected changes to the Equation interface, several standard selection functionalities do not work in the Edit Equation dialog box. These include triple-clicking to select all (although double-clicking works to select a single word) and pressing Ctrl+A to select all. You can make general comments for the model in the Design Journal, a Microsoft Word document that is embedded into the SolidWorks file. The Design Journal is found in the Design Binder folder near the top of the FeatureManager.
TIP
ON the CD-ROM
You can find the part used in this section on the CD-ROM with the filename Chapter 9 Equations.sldprt.
307
9
15_080139 ch09.qxp
Part II
3/26/07
3:41 PM
Page 308
Building Intelligence into Your Parts
Using driven dimensions Sometimes it is more convenient to use a driven (reference) dimension in an equation. This is particularly true when using geometry is the best way to calculate a number. For example, if you are manufacturing a helical auger in 90-degree sections from flat steel stock, then you need to design the auger in 3D, but begin to manufacture it in 2D. What is the shape of the auger when flat? The best way to figure this out (aside from lofted bends, which are discussed in Chapter 29) is to use a little high school geometry, a construction sketch, and some simple equations. Figure 9.5 shows a 90-degree section of an auger blade. The outside diameter is 12 inches, and the blade width is 3 inches. The overall height is 4 inches. In this case, the auger is represented as a surface because the thickness is ignored. Surface features can be useful in situations like this and are discussed in Chapter 27.
FIGURE 9.5 Representation of the auger
ON the CD-ROM
You can find the part for Figure 9.5 on the CD-ROM with the filename Chapter 9 Auger.sldprt.
With this information, we can calculate the lengths of the 3D edges using a sketch and a simple equation. In Figure 9.6, the hypotenuses of the triangles represent the helical edges of the helices. By making the triangles the same height as the auger section, and by making the horizontal side of the triangle the same length as a quarter of the inside or outside diameter by using simple equations, the geometry and sketch relations calculate the flat lengths of the inside and outside edges of the auger (length of triangle side = diameter of circle × pi / 4). In this way, the triangle is used to simplify the calculation, and give it a visual result.
308
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 309
Using Equations
FIGURE 9.6 Triangles calculate the length of the helical edge.
From this point, the flat pattern can be calculated again, using SolidWorks’ sketch-solving capabilities as the calculator. Think of the auger as being the cardboard tube inside a roll of paper towels. If you examine one of these tubes closely, you see that it is simply a straight and flat strip of cardboard that has been wound around a cylinder. What was the flat, straight edge of the original board is wound into a helix. This method is simply reversing that process. This example requires the little-used arc-length dimension to drive the size of the arc. The hypotenuse dimensions are shown by driven or reference dimensions, and these are used to drive the arc-length dimensions, as shown in Figure 9.7. Remember that you can create arc length dimensions by using the Smart Dimension tool to click both endpoints of the arc and then the arc itself. Arcs driven by arc length dimensions often do not react to changes predictably, since the radius and center or end point locations are not necessarily defined. The reasoning behind this example may be a little difficult to grasp, but the equations and the sketches are certainly simple. Using reference dimensions on the driving (independent, or right) side of the equation can in some situations require more than one rebuild to arrive at a stable value (meaning a value that does not change with the next rebuild). SolidWorks issues a warning when it sees that you are using a reference dimension in an equation, but it does allow it.
CAUTION
Equations are listed in the Equations folder in the FeatureManager. You can edit or delete them through the RMB menu.
309
9
15_080139 ch09.qxp
Part II
3/26/07
3:41 PM
Page 310
Building Intelligence into Your Parts
FIGURE 9.7 Figuring the flat pattern of the auger
Equation tricks Some functions that are allowed in SolidWorks equations are often viewed as parlor tricks, but they actually do have some practical applications. The two functions that fall into this category are IIF and SWITCH. If you are familiar with a programming language, you may already be familiar with these two functions. If not, then they are described below.
IIF In words, this is how an IIF statement is used: If some relationship is fulfilled, then the IIF function returns a value. If the relationship is not fulfilled, then it returns a different value. A more technical description is IIF(expression, value if true, value if false)
In practice, you could use it like this: IIF(x>5, x-1, x+1)
310
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 311
Using Equations
which reads, “if x is greater than 5, then subtract 1 from x; if not, then add 1 to x.” One of the reasons why this is considered a parlor trick is that this function causes the value of x to oscillate between two numbers (depending on the number that it starts with) with each rebuild. It may be difficult to imagine an application where this sort of behavior would be desirable, but when you combine it with a macro that simply rebuilds a model a number of times, you can use it to create a certain animation effect.
ON the CD-ROM
A simple example of the IIF function can be found on the CD-ROM with the filename Chapter 9 Oscillate.sldprt. The equation is shown in Figure 9.8.
FIGURE 9.8 An equation using IIF
You can find some great examples of this function at www.mikejwilson.com, along with many other extremely creative examples of SolidWorks modeling. The model on this site called Ship in a Bottle.sldprt also includes a macro that will rebuild the model a certain number of times, which is useful for animations that are created in this way.
TIP
SWITCH The SWITCH function enables you to have a list of relationships with associated values. The value of the first relationship in the list that is satisfied is returned by the SWITCH function. For example, switch (x>2, 1.5, x>1, .5 x<1, 2.5)
reads as follows: “if x is greater than 2, then the answer is 1.5; if x is not greater than 2 but greater than 1, then the answer is .5; if x is not greater than 1 but less than 1, then the answer is 2.5.” As you can see, this function does not cover all situations, but it does create a condition where the value cycles through three different numbers in a specific order. Is this useful? Possibly. Again, the main application for this function would be a simple animation for changing the size or shape of SolidWorks components that cannot be done in other more conventional ways.
Using Link Values Link values are simply a way to link several dimensions together. A link value is not exactly like an equation that sets the dimensions equal, because it does not depend on order like an equation does. All dimensions are set to the same value simultaneously.
311
9
15_080139 ch09.qxp
Part II
3/26/07
3:41 PM
Page 312
Building Intelligence into Your Parts
Link values are available by RMB clicking the dimension. Unfortunately, they are not available from the RMB menu when the dimension tool is active. To apply a link value to a new dimension, you must place the dimension, exit the dimension tool, RMB click the dimension, and select Link Value. Link values are listed under the Equations folder in the FeatureManager. Figure 9.9 shows the link values in a listed part, and the drop-down list from which you can select them or type them. Notice again that the Link Values feature also operates from a dialog box instead of the PropertyManager. I would predict that the Link Values and Equations would be redesigned to function more in sync with one another in a future version of SolidWorks.
FIGURE 9.9 Link values listed in the FeatureManager, and the Shared Values interface
The first link value that is assigned in a part must be manually typed in. After you add the first one, you can link other dimensions to this link value by using the scroll arrows shown in Figure 9.9. You cannot edit link values. In order to change the value to which a dimension is linked, you must first unlink the value and then relink it. The Unlink function is available from the RMB menu in the same way that you assign link values. Dimensions that have a link value have the small chain symbol displayed to the left of the dimension. There is one link value name that has a special significance. If you use the name thickness, then a Link To Thickness option appears in all extrude dialog boxes. This is intended to reflect sheet metal functionality, but it is useful for models of various manufacturing techniques.
TIP
To take this one step further, you can save a part template with a thickness link value; all of your new parts will also have this functionality right from the start. To save the template with a link value, you must create at least one dimension to assign the link value, and then delete the geometry (and the dimension); however, the link value will remain.
Link values of different types are not necessarily interchangeable. You cannot use angular dimension link values on radius, diameter, or linear dimensions. You can use linear and diameter link values interchangeably, but not angle link values.
312
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 313
Using Equations
Using Global Variables Global variables are assigned in the Equations dialog box as simply the variable name equaling the value. Figure 9.10 shows a list of equations, link values, and global variables. When you are typing in the name of the variable, you do not need to add the quotation marks; they are added automatically.
FIGURE 9.10 Equations, link values, and global variables
Despite the word variable in the name global variable, the values are not variable. They are fixed, and only changeable through the Equations dialog box. The only place where you can use global variables is in equations. You cannot directly enter them into dialog boxes for dimension values.
Using Expressions Expressions, unlike all of the previous variables, values, and equations, can be entered directly into dimension dialog boxes. The expressions have to be composed of numbers and mathematical operators. An expression such as 2.375+(4.8/3) -1.1
is perfectly acceptable, as is 1+1/2
or 1 1/2.
In the second case above, the plus symbol is understood.
313
9
15_080139 ch09.qxp
Part II
3/26/07
3:41 PM
Page 314
Building Intelligence into Your Parts
Other types of operations are also available, such as changing units in a dimension box. For example, if you are editing a part in inches, and enter 40mm, then SolidWorks does the conversion for you. You can even mix units in a single expression such as 4.875+3.5mm, where the inch part is assumed.
Tutorial: Using Equations Follow these steps to get some practice with using equations: 1. Start from the part on the CD-ROM with the filename Chapter9 Tutorial Start.sldprt. 2. Show the dimension names. This setting is found at Tools ➪ Options ➪ General ➪ Show Dimension Names. 3. Double-click the Circular Pattern feature to display the angle and number of instances of the feet and related features. You may have to move the angle dimension to see the pattern instance number. 4. RMB click the instance number, and select Properties. Change the name of the dimension to # (pound or number sign). 5. Double-click the first feature, which is the revolve, and rename the 3.60-inch dimension to CapRad. 6. Write an equation that drives the number of legs by CapRad/7. a. Open the Equations dialog box at Tools ➪ Equations. b. Click Add to add an equation. c. Double-click the Circular Pattern and click the # dimension. Make sure that the name of the dimension is listed in the equation box, and type an equal sign. d. Double-click the Revolve feature and select the CapRad dimension; then type the characters /7. e. Add a comment to the equation to reflect which dimension is driving which dimension. 7. Click Rebuild, press Ctrl+B or Ctrl+Q to rebuild the model, and observe whether any update takes place. 8. Rename the 6.00-inch dimension for the height of the revolved feature to DomeHt. 9. Create a second equation that drives the DomeHt dimension at the current ratio of the height to the radius. a. Create a global variable called Ratio = 6/3.6 (1.66667) in the Equations dialog box. b. Create the equation. The equation will take the form of DomeHt = (Ratio) × CapRad. 10. Use a link value to make the radii of Fillet1 and Fillet2 the same. 11. Double-click Extrude2. Change the .75-inch dimension to .05+20mm (.79"). 12. Save and close the part with a new name, including your initials or the date.
314
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 315
Using Equations
Summary SolidWorks equations and related dimension-management tools are powerful, but often leave you wishing for a little more flexibility and control. The interface is not up-to-date with the rest of the SolidWorks interface, and so I would look to see an updated equation interface soon that integrates dimension input, link values, and global variables. If you want to encourage SolidWorks to revise certain features, then you can go to the SolidWorks Web site and submit an enhancement request. They do look at customer input when developing or updating functionality.
315
9
15_080139 ch09.qxp
3/26/07
3:41 PM
Page 316
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 317
Working with Part Configurations
C
onfigurations, also known as simply configs, are variations of a part in which dimensions are changed, features are suppressed (turned off), and other items such as color may also be controlled. Configurations enable you to have these variations within a single part file, which is both convenient and efficient. This chapter deals only with part configurations, but you should be aware that assemblies can also have configurations. Assembly configurations can use different part configurations, among other things. This will mean more to you as you learn about part configurations.
CROSS-REF
Assembly configurations are discussed in Chapter 14.
One example of the use of configurations is Toolbox. By default, Toolbox uses configurations to create many sizes of hardware within a single part file. For example, the Socket Head Cap Screw is a single part in Toolbox that contains hundreds of sizes. You can change the size by simply varying the dimensions of the existing features. Toolbox parts also have features that you can turn off and on (suppress and unsuppress, respectively), particularly those related to thread representation (swept versus revolved versus cosmetic). Changing dimensions and suppressing or unsuppressing features are the most commonly used techniques that are available through configurations.
317
IN THIS CHAPTER Manually controlling items with configurations Using design tables Tutorial: Working with configurations and design tables
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 318
Building Intelligence into Your Parts
Controlling Items with Configurations With every new release of SolidWorks software, it seems that there are new items that become “configurable,” that is, able to be driven by configurations. Configurable items for parts include the following: n Feature dimensions, driving/driven state n Suppression of features, equations, sketch relations, and end conditions n Which sketch plane is by a sketch n Configuration-specific custom properties n Part, body, feature, and face colors n Derived configurations n The ability to assign properties such as mass and center of gravity n Configuration of base or split parts You can work with configurations in one of two ways: either manually or through a design table. I describe the manual method first, to give you a good understanding of how to intervene with configs the manual “old-fashioned” way when you need to. Design tables are a fantastic way to organize and manage config data and options, but they also require a bit of syntax, and so I will describe them in a separate section later in this chapter.
Finding configurations You can handle configurations in the ConfigurationManager. This is the third tab in the FeatureManager/PropertyManager interface. You can split the FeatureManager interface into two by dragging the splitter bar at the top of the panel. This is a very useful function that allows you to see the FeatureManager in the upper panel and the PropertyManager or ConfigurationManager in the lower panel.
TIP
Deleting configs Each part has a default config named “Default.” There is nothing special about this config; you can rename it and even delete it. There must always be at least one config in the tree, and you cannot delete the current configuration. If you would like to remove a config, then you need to switch to another config first, and then delete it. In relation to assembly configurations, you cannot delete a config if it is being used in an assembly that is open and resolved. In order to delete a config such as this, you need to either close the assembly or change the part config used in the assembly. If you try to delete a configuration being used by an open assembly, SolidWorks simply gives the message “None of the selected entities could be deleted” without explanation.
318
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 319
Working with Part Configurations
If you delete a configuration of a part that is used in an assembly, but the assembly is not currently open, the next time the assembly is opened it issues the message “The following component configurations could not be found . . . . If the configuration was renamed the same configuration will be used, otherwise the last active configuration will be substituted for each instance.” As you can see, a configuration that is simply renamed is dealt with differently than a configuration that is deleted. In any case, you need to be careful when dealing with parts with configurations that are used in an assembly. Many users get into the habit of clicking out of any error, warning, or message box that comes up, often without reading what it has to say. It is important to read error and warning messages when they come up. Some of them, such as the configuration message shown previously, are vitally important to the integrity of your design data. They are sometimes actually useful.
NOTE
You can delete groups of configs by window select, Shift-select, or Ctrl-select in the ConfigurationManager. You can also use the RMB menu, much like regular features in the FeatureManager.
Sorting configs In the ConfigurationManager, configs are listed alphabetically, not in the order in which they are created. This has several advantages, especially when you have a large number of configs. For example, if configs are named by size in a part that you are working with, then when selecting a configuration, you can type in a number, and the selection scrolls to that place in the list of configs. This makes it easier to select the one you are looking for, much the same as it works in Windows Explorer.
Alphabetization This alphabetized order is significant because many other sections of the SolidWorks interface are not alphabetized, which causes problems when you are searching for items in larger lists. Sections that are not alphabetized include Help/Contents, Files Of Type lists in Open and Save dialog boxes, and the Tools/Options/File Locations, Entity Color list. If you are inclined to send in an Enhancement Request, alphabetization is one topic that would benefit everyone and should be fairly easy for SolidWorks to implement.
Naming configs In order for this sorting and alphabetization to work, you must first name the configs properly. For example, if you have a list of sizes or config names from 1 to 100, then you should use 001, 002...100 as your syntax. This makes the config names easier to browse and type in. Syntax becomes most important when you place a part with many configs into an assembly, because you must select a config from the list, and typing in the first few numbers is often faster and easier than scrolling to it.
ON the CD-ROM
The CD-ROM contains a part called Chapter 10 Config Names.sldprt, which illustrates proper naming and alphabetization.
To understand this technique better, you can open the part called Chapter 10 Config Names.sldprt from the CD-ROM, split the FeatureManager area, and change one of the panes to display the
319
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 320
Building Intelligence into Your Parts
ConfigurationManager. Click one of the configuration names, and type in a number between 001 and 100. The highlight scrolls to the number that you typed in. Thoughtful selection of the configuration names can save you and your coworkers a lot of time when you need to insert select configs into an assembly. Figure 10.1 shows this arrangement.
FIGURE 10.1 The split FeatureManager, displaying the ConfigurationManager
CROSS-REF
The splitter bar and other portions of the FeatureManager interface appear in Chapter 2.
Activating configurations Within a part file, to change the display from one configuration to another, you must first switch to the ConfigurationManager panel, and then either double-click the desired config or RMB click it and select Show Configuration. Alternatively, you can RMB click the config in the ConfigurationManager and select Show Preview, as shown in Figure 10.2. A small preview thumbnail displays in the PropertyManager panel. However, not all configurations will have previews. For example, in a part with many configs that have been generated automatically by a design table, the configurations may not have previews because the config itself has never actually been rebuilt. Previews exist only when the configuration has been activated once, the image on the screen generated, and the part then saved. SolidWorks stores both the body (geometry) and the preview image of the part so that next time you access the configuration, the software does not have to rebuild everything again.
320
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 321
Working with Part Configurations
FIGURE 10.2 Showing a configuration preview
You can even select a configuration while opening a file. This allows you to save time by avoiding two model rebuilds. To take advantage of this option, you must use the File ➪ Open interface, which is shown in Figure 10.3. You can select the config from the lower-right list window, using the same technique of typing in the first few characters of the config name.
FIGURE 10.3 Selecting a configuration from the Open dialog box
321
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 322
Building Intelligence into Your Parts
Creating configurations You can create configs manually or through Excel-driven design tables. Design tables are extremely useful for situations where there are more than a few configs, or more than a few items are being controlled. You should use design tables because they keep things very organized within the spreadsheet grid. For now, I am going to focus on creating and manipulating configs manually so that you can become familiar with them without also worrying about Excel and design table syntax.
Making a new config To make a new config, you can RMB click the top-level icon in the ConfigurationManager, which displays a part symbol and the name of the part, and select Add Configuration. Figure 10.4 shows the RMB menu and the Properties dialog box that you can use to set up the new config.
FIGURE 10.4 Creating a new configuration
Configuration properties and options The name of the config is important mainly for quick access and organization purposes. The configuration description is also important, because it can display in the ConfigurationManager, and even in the Assembly tree. This is important when the name of the config is numerical rather than descriptive, and you would like to also have a description but not include it in the name. The config description can also appear in place of the filename in the Assembly tree display. I discuss this
322
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 323
Working with Part Configurations
in more detail in Chapter 12. Config descriptions can be driven manually through the Configuration Properties dialog box or through a design table if you have many configs to manage. You can display config descriptions through the RMB menu, as shown in Figure 10.5.
FIGURE 10.5 Enabling configuration descriptions
I discuss the Bill Of Materials options in Chapter 24, but the option is set in the Configuration Properties to use the filename, the configuration name, or a custom name that the user specifies. You can save this setting with a template. Control over configurations is achieved through the combination of the Configuration Properties and the Advanced Options, which are discussed next. Although you can change the preferred settings at any time, it is definitely a best practice to make a template early on when you are using SolidWorks to model parts. SolidWorks remembers the Bill of Materials options and Advanced options that you set for the Default configuration and uses them in document templates. This is true for both part and assembly templates.
BEST PRACTICE
Advanced options The two advanced configuration options are found in the bottom panel of the Configuration Properties PropertyManager. Suppress Features and Use Configuration Specific Color are the two options available. While the second option is self-explanatory, the first one is not, and often catches new and even experienced users off guard. Suppress Features refers to how inactive configurations should handle new features. For example, if you have two configs, 1 and 2, and config 1 is active and you add a new Fillet feature, then what happens to that feature in config 2? If this option is turned on, then the new features are suppressed. If it is turned off, then the new features will be unsuppressed when the inactive configs are activated. This creates a much bigger challenge for manually created configurations than for design table-driven configs because changing suppression states for several features across multiple configs is much easier in a design table than in manual config management.
323
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 324
Building Intelligence into Your Parts
Derived configurations Derived configurations are configs that are dependent on other configs. You can create them from the RMB menu on a configuration instead of on the top level in the ConfigurationManager, and they appear indented underneath the parent config. Figure 10.6 shows the RMB menu and the position of the derived config in the tree.
FIGURE 10.6 Creation and placement of the derived config
Derived configurations maintain the same values and properties of the parent config unless you break the link to the child config by explicitly changing a value in the child config. For all other values, the child config value changes when the parent config value changes. One very nice application of derived configs is to use them for simplified configurations, and set the properties so that any features that are added to the parent config are also added to the derived config. You can do this by setting the Advanced Option Suppress Features to Off. This causes the derived config to inherit only features that are added to the parent, and not to other configs. The simplified configs are used for FEA, making drawings of models where all of the edge breaks have actually been modeled. They are also used for the reverse (a complex config rather than simple) to have a config that includes fillets for rendering purposes that are otherwise not there. You can also create and maintain derived configs using design tables, which are discussed in the next section.
File size considerations A long-standing dispute has raged over the effects of file size on speed. Here are the facts: When SolidWorks creates a configuration, it stores information about the 3D geometry and a preview thumbnail of the configuration inside the part file. This makes it faster to access the configuration the next time because it has only to read the data, rather than read other data and then recalculate the new data. As a result, saving the stored data allows you to avoid having to recalculate it.
CROSS-REF
Appendix A contains a section on Data Management that has several options for dealing with data and large file sizes.
File size has a negative effect on speed when you are sending data across the Internet or working across a network. If the data is on your hard drive, then storing data instead of calculating it offers a big benefit.
324
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 325
Working with Part Configurations
SolidWorks 2007 Service Pack 1 has a fix associated with it that takes advantage of a new hotfix from Microsoft that removes shadow data from files, and may reduce the size of SolidWorks files to one-half or even one-quarter of their original size. See the SolidWorks Customer Portal and the Microsoft support site for details regarding Microsoft Knowledge Base article 919880. The Microsoft hotfix files can be found on the SolidWorks support site. Files with many configurations are supposed to derive the most benefit from the combination of this service pack and hotfix.
NOTE
Controlling dimensions Controlling dimensions with configurations is simple. You need only three things to start: one dimension and two configurations. Because you already know how to create these elements, you are ready to start. Configurations require that you spend some time developing “design intent” for parts. Configurations drive changes in models, and if they are improperly modeled, then configurations will cause feature or sketch failures. I will start with the example of a simple block. A fully dimensioned block has three dimensions. Make sure that you have manually created at least two configurations. Double-clicking the model brings up all of the dimensions, and double-clicking one of the dimensions brings up the familiar Modify dialog box. Or almost familiar, I should say; Figure 10.7 shows that there is a small difference in the new Modify dialog box. It now has a drop-down list where you can specify whether this change applies only to this config, to all configs, or to specified configs. If you select specified configs, then the dialog box on the right in Figure 10.7 appears, where you can select which configs this dimension change applies to.
FIGURE 10.7 Making simple changes to a configuration
First config
Second config
325
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 326
Building Intelligence into Your Parts
Once you are finished, you can toggle back and forth between the configs by double-clicking each of the configs in the ConfigurationManager. Although this is simple, if you forget to change the drop-down list from the All Configurations setting to either the This Configuration or the Specify Configuration(s) setting, then you apply the change to all of the configurations. This example shows that building a configuration manually is fine for a few simple changes, but it can become unwieldy if you are changing more than a few dimensions in this way. You would then have to remember which dimensions were changed to what. As you can see, using design tables is a better method for multiple dimensions.
Controlling suppression Suppressing a feature is just like turning it off; the feature appears as grayed-out text in the FeatureManager. With configurations, you can suppress a feature in one config and unsuppress it in another. When dealing with manual configuration techniques, there are two methods for controlling suppression: manually suppressing features, and creating configurations with the appropriate options for the inclusion of new features that I discussed previously in this chapter. In addition to the Suppress toolbar button, you can also use the Unsuppress and Unsuppress with Dependents features. When you suppress a feature, any feature that is dependent on it is also suppressed. If you then use the Unsuppress feature, it unsuppresses only the feature itself. However, Unsuppress with Dependents brings back all of the dependent features, as well. Suppressing complex features is a great way to improve performance. Experienced users often create a configuration of a part that they use as a simplified config, where patterns, fillets, and extruded text features are suppressed. This becomes more important as you start working with assemblies.
PERFORMANCE
Generally, SolidWorks users employ a combination of these methods, mainly because configurations are not usually started on a complete model; they are often added when the model is still in progress, and so features are added after the users create the configurations. Figure 10.8 to the left side of the image shows a feature that is both unsuppressed and suppressed in the tree. The text and icon for the suppressed feature are grayed out. You can suppress features from the RMB menu on the feature, from the Edit menu, or through a tool on a toolbar. The Suppress button is not on a toolbar by default, but you can find it in the Tools ➪ Customize ➪ Commands dialog box, along with the other buttons for the Features toolbar. Only the menus offer the options of Unsuppress With Dependents, as well as the This Configuration/All Configurations/ Specify Configurations options for each of the Suppress, Unsuppress, Unsuppress With Dependents functions. When you control suppression in manually managed configurations, you will often need to switch between configs to ensure that you have applied the correct dimensions and suppression scheme. As a result, manual configuration management is not a desirable method.
326
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 327
Working with Part Configurations
FIGURE 10.8 Suppressing a feature
Controlling custom properties Custom properties fall into a category of model data called metadata, which is text-based information. This metadata is meant for any text-based data that you would like to accompany the part, such as description, material, vendor, vendor part number, price, or even cost. Several reasons may compel you to use custom properties, including search criteria for a Product Data Management system, automatically filling out drawing title blocks, or adding information to the Bill of Materials. When you are using custom properties with configurations, you must use the Configuration Specific Custom Properties interface, which enables you to have custom properties that change with each configuration. This is useful for situations such as different part numbers for configurations, and many other situations that are limited mostly by your use of configs. The interface for managing custom properties manually is shown in Figure 10.9. You can access this dialog box through menus at File ➪ Properties. If you are using a newer version of SolidWorks, then you may notice that the interface has improved drastically in recent versions. You can also link custom properties to mass properties, model dimensions, link values, and global variables by selecting from the drop-down list under the Value/Text Expression column, which appears when you select a cell in the column, as shown in Figure 10.9. To link a custom property to a model dimension, simply place the cursor in the Value/Text Expression box that you want to populate, and click a dimension in the graphics window. Again, managing this data for a single config or only a few configs is easy enough; however, it can quickly become unwieldy, which is where using design tables can make a huge difference.
327
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 328
Building Intelligence into Your Parts
FIGURE 10.9 The Configuration Specific tab in the Summary Information dialog box
Controlling colors Face, feature, body, and part colors as well as materials are also configurable. Just switch to the configuration you want to control, and make the changes. New in SolidWorks 2007 sp1 is a button in the Color Properties dialog box labeled Remove All Colors. You do not need to have anything selected for this function to work, but it only works for the current configuration. It removes all colors that are assigned to anything but the part level (the part needs to have a color assigned to it). In the past, users required a macro to eliminate special colors.
NEW FEATURE
Controlling sketch relations You can individually suppress or unsuppress sketch relations using configurations. Figure 10.10 shows the Display/Delete Relations PropertyManager interface, at the bottom of which is the Configurations panel. To suppress a relation, select it from the list and select the Suppressed option in the Relations section above the Delete buttons.
328
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 329
Working with Part Configurations
FIGURE 10.10 The Display/Delete Relations dialog box for configuring sketch relations
This is another situation where Delete is not used as an editing option. Using this technique, you can save sketch relations, or activate different sets of relations in different configs; this technique allows a single sketch to react to changes differently.
TIP
Controlling sketch planes You cannot configure the Offset distance in the From option for extrudes, but you can configure the sketch plane for the sketch that is used in the feature. The Sketch Plane PropertyManager interface expands when configurations are present, as shown in Figure 10.11.
329
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 330
Building Intelligence into Your Parts
FIGURE 10.11 The Sketch Plane PropertyManager interface for configuring a sketch plane
Another way to change the sketch plane is to put the sketch on an offset plane or a plane that can otherwise be driven by a dimension (for example, using reference sketch geometry). Actually moving a sketch to another plane can cause the sketch to rotate or flip. Moving the plane it is on is a better option that does not cause the sketch to rotate or flip.
TIP
Changing sketch planes indiscriminately can have serious consequences for your model. “Face/Plane Normals” sometimes point in different directions, and can cause a sketch to flip, rotate, or mirror when you change it from one plane to another. One strange result is that changing it back to the original location can cause the sketch to flip again, but in a different way so that it does not go back to its original location/orientation. As a result, every time you change the configuration, the sketch could appear in a new and unexpected location or orientation.
CAUTION
Controlling configurations of inserted parts Inserted parts have a long history in SolidWorks. They have had several names in the past, and some sources (including SolidWorks documentation such as training documents and even help files) still use some of these names out of habit or precedence. For example, you will sometimes hear inserted parts called derived or base parts.
CROSS-REF
Inserted parts are discussed in detail in Chapter 28, which describes master model techniques.
Inserted parts use one part as the starting point for another part. The inserted part sits as a feature in the FeatureManager of the child part. The features of the original inserted part are not brought forward; only the finished solid body or bodies, select surface bodies, planes, and cosmetic threads are brought forward. It is a major point of contention for many people that you should also be able to bring forward sketch data, but this option is not available at this time (however, if you have a bookmark to that enhancement request site, you may want to request this feature).
330
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 331
Working with Part Configurations
The role of configurations with inserted parts is that the configuration of the inserted part can be controlled from the child component. For example, you may have designed an engine block for an automobile. This engine block is a casting, and using configurations, you have both the six-cylinder and the eight-cylinder blocks in a single-part file. This model represents the “as cast” engine block. The next step is to make the block with all of the secondary machining operations, such as facing mating surfaces, reaming cylinders, drilling and tapping holes for threaded connections, and so on. As a result, the as-cast part is inserted into the as-machined part, and the configuration is selected before you add the cut features. As the name suggests, you add inserted parts through the menus using Insert ➪ Part. The interface for assigning the configuration is shown in Figure 10.12. Simply RMB click the inserted part feature and select List External References.
FIGURE 10.12 Assigning the configuration of an inserted part
Library features Library features can have configurations, and they carry those configurations with them into the part in which they are placed. Unfortunately, part configs cannot reference different library feature configs.
CROSS-REF
Chapter 17 discusses the Hole Wizard, and Chapter 18 discusses library features.
331
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 332
Building Intelligence into Your Parts
Configurations for library features are created in exactly the same ways that configurations are created for other parts. The technique for saving the configs to the library feature is discussed in Chapter 18.
Unconfigurable items As important as it is to know what you can do, it is equally important to know what you cannot do. The following is a list of items that are not configurable. Although this list is not complete, it contains many of the more relevant items that cannot be configured: n Hole Wizard holes (although there is a workaround: dimensions can be configured) n Library feature configs n Blocks n Extrude direction or From Offset dimension or direction n Most of the values in features such as Deform, Freeform, and Twist n Hide/Show state of a body
Using Design Tables In addition to describing some of the basic concepts involved with configurations, the first part of this chapter has offered reasons for using design tables. For example, while manual configuration management can be haphazard, and is highly prone to mistakes, design tables lay everything out in an Excel spreadsheet. Although many new users ask whether they can use a different replacement spreadsheet program, you must use Excel.
NOTE
The versions of Excel that are supported by SolidWorks for design tables are XP, 2000, and 2003. Although Excel 97 may still work, Microsoft no longer supports that product.
Excel is a format that is easy to read and print out, and even non-SolidWorks users can understand and work with it. Although there is some special syntax that you need to use with design tables, for most uses, SolidWorks can create the syntax automatically for you, and so there is a minimum of manual data entry. If you are careful to name dimensions, features, and configurations properly, design tables should be easy to understand and manage. Excel can also color cells, rows, and columns in such a way that large amounts of tabulated data are easier to sort through. In addition, because design tables use Excel, they can also use Excel’s equations. When using equations and design tables, it is considered best practice to name dimensions, sketches, features, and other configured items. However, it is not recommended to mix design tables with SolidWorks equations. Besides the fact that Excel equations are far more sophisticated than those of SolidWorks, driving dimensions from too many locations can be confusing when you edit the part after you have forgotten the details of how the part was built.
BEST PRACTICE
It is a great idea to document design intent using comments in the features or the Design Journal. You should also add comments to design tables as needed.
332
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 333
Working with Part Configurations
What can be driven by a design table? Just because something can be configured does not necessarily mean that it can also be driven by a design table. Here is a small list of items that fit into this category: n Sketch plane configuration n Suppressed sketch relations n Suppressed dimensions (suppressed dimensions become driven dimensions) However, the good news is that there are many items that can be driven by a design table. Table 10.1 lists these items, along with their associated syntax.
TABLE 10.1
Items That Can Be Driven by a Design Table Item
Syntax (Goes in Column Header)
Possible Values (Goes in Field Cell)
Default Value If Field Is Blank
Configs of Inserted Parts
$configuration@ <part name>
not evaluated
Configs of Split Parts
$configuration@ <split feature name>
not evaluated
Comment Column
$comment
comment text
blank
Configuration Description
$description
description text
BOM Part No.
$partnumber
$d, $document = document name $p, $parent = parent config name $c, $configuration = config name = custom name
config name
Feature Suppression State
$state@
suppressed, s unsuppressed, u
present suppression state
Dimension Value
dimension@ dimension@ <sketch name>
allowed numerical values
not evaluated
Parent Config (creates a derived config)
$parent
parent config name text
not evaluated
Config Specific Custom Property
$prp@<property name>
property name text
not evaluated
Equation State
$state@ <equation number>@ equations
suppressed, s unsuppressed, u
unsuppressed
continued
333
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 334
Building Intelligence into Your Parts
TABLE 10.1
(continued)
Item
Syntax (Goes in Column Header)
Possible Values (Goes in Field Cell)
Default Value If Field Is Blank
Light Suppression State
$state@
suppressed, s unsuppressed, u
unsuppressed
Sketch Relation Suppression
$state@ suppressed, s @<sketch name> unsuppressed, u
unsuppressed
User Notes (same as comment)
$user_notes
blank
Part or Feature Color
$color see SolidWorks Help, $color@ Colors, Parameters in design tables
0, black
Assigned Mass Mass properties
$sw-mass
allowed numerical values
value from
Assigned Center of Gravity X, Y, Z Coordinates
$sw-cog
allowed numerical values in the format of x, y, z
value from Mass properties
Dimension Tolerance
$tolerance@
see SolidWorks Help, Tolerance Keywords and Syntax in Design Tables
none
Text
Creating a simple design table When you prepare to create a design table, you generally need to give appropriate names to dimensions, sketches, and features. Remember that while the feature is the most visible item and the easiest to rename, most of the dimensions probably belong to the sketch, which you may also need to rename. Names should reflect the function or location of the item. It is a good idea to show dimension names when renaming items (remember that you can show dimension names by turning on the option at Tools ➪ Options ➪ General ➪ Show Dimension Names). Figure 10.13 shows the result of renaming the feature and dimension. You can use one of the following three techniques to add a design table to a SolidWorks part: n Insert Blank Design Table: This method starts from a blank template that contains the underlying framework, but no values. n Auto-create Design Table: This method populates the new design table with any existing configurations and items that are different between the configs. n From File: This method allows you to create a design table externally and then import it.
334
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 335
Working with Part Configurations
FIGURE 10.13 Renamed features and dimensions
Although I prefer the Auto-create method, it is most appropriate for when you have existing configurations. The From File method is best when a design table has been exported from another part, saved externally, and brought into the current part. For the following example, I am using the Insert Blank Design Table method.
ON the CD-ROM
If you would like to follow along with these steps to create the design table, you can use the part from the CD-ROM with the filename Chapter 10 DTstart.sldprt.
Figure 10.14 shows the results of starting with the new blank design table. You may notice that the window title bar at the top says SolidWorks, but the toolbars look a lot like the Excel interface. This is because Excel is actually running inside of SolidWorks. Clicking outside of the Excel window can cause the Excel window to close, although there are several items outside of the Excel window that you can select without the window closing, such as features in the FeatureManager and dimensions in the graphics window. You can also rotate and pan the view in the graphics window without closing the Design Table window. If you are very careful, you can also drag the thin hatched border of the Excel window to adjust its size or location. Design Tables also can be edited in a separate window, which makes editing easier, but makes adding dimension and feature names more difficult. To edit the table in its own window, RMB on the Design Table in the FeatureManager and select Edit Table In New Window.
335
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 336
Building Intelligence into Your Parts
FIGURE 10.14 The interface where you can create the design table, and the resulting blank design table
Figure 10.15 shows a fully developed design table, with some complexity. Although your first design table does not need to be this complex, this example demonstrates what you can do with this feature. The config names go in the first column, and the feature or property names go in the second row. The first row is reserved for the name of the table. All of this is automatically set up by SolidWorks. Because you are actually working in Excel when working with design tables, you can use Excel formatting, which is how the text in Figure 10.15 is rotated 90 degrees for the column headers. (To rotate text in a table, RMB click the cell, group of cells, or row; select Format Cells; and then select the Alignment tab).
NOTE
In our new design table, the next step is to type in some configuration names. Because you are working in Excel, all of the fill functionality is available. In the example shown in Figure 10.16, I have typed in the first three values of 001, 002, and 003, then window-selected the cells, and dragged the fill handle on the selection window to fill the number pattern to populate a larger area. To find more information about this technique, look for Fill or Automatically Number Rows in the Excel Help files.
336
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 337
Working with Part Configurations
FIGURE 10.15 A fully populated design table
Config names Feature or property syntax from table
FIGURE 10.16 Filling in configuration names
337
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 338
Building Intelligence into Your Parts
The next step is to fill in some feature and dimension names in the second row. The first thing that you do is to suppress the HexDrive feature. To make this the first feature in the list, click in cell B2, and then double-click the HexDrive feature in the FeatureManager. The name of the feature and its current suppression state are added to the design table with all of the necessary syntax and correct spelling. To rotate the text in this row vertically, RMB click row number 2, select Format Cells, click the Alignment tab, and turn the orientation to 90 degrees. The word unsuppressed displays with all c apitals and fully spelled out, while all you need is a U or an S. Replace the word with an S, and double-click the line between the column heading letters B and C at the top of the Excel window, to condense column B as much as possible. Alternate the rest of the rows between Us and Ss to either suppress or unsuppress the HexDrive feature in various configurations. Figure 10.17 shows the current state of the design table.
FIGURE 10.17 Building the design table
Close the Design Table window, and click OK on the message box that lists the new configurations created by the Design Table. Now split the FeatureManager, set the lower pane to the ConfigurationManager, and double-click some configurations. Notice that in the configs where you specified an S, the HexDrive is suppressed, and no longer appears in the model.
338
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 339
Working with Part Configurations
You can now add a dimension to the design table. To add a dimension, it is most convenient to display the dimensions on the screen at all times. To show all of the dimensions in the part, RMB click the Annotations folder in the FeatureManager and select Display Annotations. If the dimensions do not display, then you may have to go back and select Show Feature Dimensions. Arrange the dimensions so that you can clearly see them all, as shown in Figure 10.18.
FIGURE 10.18 Dimension and annotation display settings
To display the design table again, locate it in the FeatureManager list, just below the Origin, RMB click it, and select Edit Table. Editing the feature changes the settings used for the design table. Edit Table in New Window is an option that we will use later because it simplifies many things; however, for now, the Edit Table option makes it easiest to add new items to the design table. If a window appears with the name Add Rows and Columns, just click OK for now. This window lists parameters that have changed in its lower pane, and it is asking you if you would like to add any of the changed parameters to the design table. If you would like to add them, just select the parameter in the lower pane and click OK. If not, just click OK.
NOTE
If the design table displays on top of your model, you can either move the model or move the design table. Moving the design table is a bit tricky, and involves dragging the striped-line border of the Excel window; remember not to grab it at the corners or midpoints, because this will simply resize it. If you click inside the border, nothing happens. If you click outside of the border, the Excel window closes. Moving the model may be easier. To do this, just Ctrl-drag in blank space in the graphics window; it pans the display so that you can see the part dimensions. With cell C2 selected, or whatever the next available cell is in the second row, double-click the OverallLength dimension in the graphics window. SolidWorks adds the proper syntax to the design table, along with the current value for the first configuration in the list. Fill in values for the rest of the configurations. These values can then be calculated in Excel using any of the available techniques.
339
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 340
Building Intelligence into Your Parts
Exit the design table and toggle through the various configurations to see their different lengths. These examples should get you started on more complex configurations and design tables. Any dimensions that are controlled by the design table (and that are therefore locked) display in pink on the screen.
Design table settings Figure 10.14 shows the PropertyManager for design tables. After you have created the table, you can edit the table settings by RMB clicking the table and then selecting Edit Feature. Edit Feature enables you to edit the settings for the table only; it does not enable you to edit values within the table.
Linked design table By selecting the From File source option, you can create a design table from an external file; you can also link the table to the external file. When you use the other two options, Blank and AutoCreate, SolidWorks stores the Excel file within the SolidWorks document. Linking to an external file may be useful if you have a non-SolidWorks user who is entering data into the design table, or if a single table controls multiple parts.
Edit control The Edit Control panel has two options, which act as a toggle. The Allow Model Edits To Update The Design Table option is self explanatory, as is its opposite, the Block Model Edits That Would Update The Design Table option. If the Allow Model Edits option is selected, and you make a manual change to the model, the next time you open the design table, SolidWorks warns you about the change and that it will update the design table. Likewise, if you try to make a manual change and the Block Model Edits option is selected, you receive a warning that the value cannot be changed.
Options The Options settings determine the behavior when you are using the Allow Model Edits option and a new item has been configured. For example, the design table may already exist, and you manually add a configuration and suppress a feature. Configurations that have been added manually are displayed somewhat differently from configs that are being managed by the design table. Figure 10.19 shows the two configurations at the bottom of the tree with square symbols, while the design table configs have Excel symbols.
FIGURE 10.19 Manually created configs versus design table–created configs
340
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 341
Working with Part Configurations
After you manually add the config and suppress the feature, the next time you open the design table, the Add Rows and Columns dialog box appears. Most users are simply annoyed by this, but that may be because they do not understand what it does or why it appears. In the example shown in Figure 10.20, a new configuration has been manually added; it appears in the Configurations box as Manually Added Config, and in the Parameters box, it looks like a feature named BodyChamf has been either suppressed or unsuppressed manually. The appearance of this dialog box means that SolidWorks is asking you if you would like to include these items in the design table. If so, then simply select the items you would like to add to the design table and click OK. If you do not want to include the items in the design table, then simply click OK or Cancel. If you click OK, then you will not be offered these choices again; if you click Cancel, then the next time you open the table, the dialog box with the same choices will reappear. If you never want to see this dialog box again, then make sure that all of the options in the Options panel shown in Figure 10.14 are turned off.
FIGURE 10.20 The Add Rows and Columns dialog box
Editing the design table As mentioned earlier, when you open the design table inside the SolidWorks window, it can sometimes be difficult to work with. One way to handle this problem is to only edit the design table inside SolidWorks when you want to add new features to the column headers, and when adding new configurations or editing the field values, edit the table in a separate window. This option appears on the RMB menu, as Edit Table in New Window. It allows you much more flexibility in resizing the Excel window, changing zoom scale, and other operations, but it does not allow you to double-click a dimension so that it is added automatically to the column header.
341
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 342
Building Intelligence into Your Parts
When working on design tables, it is a good idea to avoid conflicts with other sessions of Excel by closing any other Excel windows. The combination of operating Excel spreadsheets inside both SolidWorks and Excel has been known to cause crashes, or the “Server Busy” warning message. If you are diligent about having only one session of Excel active at a time when you are working on design tables (or Excel BOMs), then there is less likelihood of a crash or conflict.
CAUTION
Tutorial: Working with Configurations and Design Tables Throughout this book, parts that I use for one purpose may also be interesting for other purposes as well. For example, the part used in this tutorial uses a loft with guide curves where both guide curves are created in the same sketch. The guide curve sketch is made from symmetrical splines where I have used the spline handles to change the shape smoothly and in a controlled way. I have also used a curve-driven pattern to go around an elliptical shape. If at some point you decide that you have made mistakes from which you cannot recover, or you would simply like to start over again, you can select File, Reload. This is the same as exiting the part without saving, and then reopening the part to start from the beginning.
TIP
To start working with configurations and design tables, follow these steps: 1. From the CD-ROM, open the part called Chapter 10 Tutorial start.sldprt. Take a moment to become familiar with this part by using the rollback bar to see how it was made. In particular, look at the two patterns, which need to be parametrically linked. Figure 10.21 shows the part.
FIGURE 10.21 The Chapter 10 Tutorial start.sldprt file
342
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 343
Working with Part Configurations
2. Manually create a configuration for the part called Size 1. Remember that to create a configuration, you must show the ConfigurationManager tab in the FeatureManager area, and RMB click the name of the part at the top level. It is better to do this by splitting the FeatureManager window and setting the lower pane to the ConfigurationManager. 3. Set the Advanced option to both Suppress Features and Use Configuration Specific Color (both turned on). 4. Before closing the Add Configuration PropertyManager, click the Color button on the Advanced Options panel of the Configuration PropertyManager and select a different color for the Size 1 configuration. The color does not change immediately. It will change after you close the PropertyManager. 5. Turn on the Tools ➪ Options setting to Show Dimension Names. (Remember, this the third option on the General page). 6. Double-click the feature CrvPattern1 in the FeatureManager. A number 6 with a D1 under it will appear on one of the holes in the pattern. If you have changed your part to a blue color, then it may be difficult to see, because the text will also be blue. 7. Change the name of the dimension to Hole# by RMB clicking the dimension and selecting Properties. 8. Change the value of the number to 8, and be careful to also change the drop-down setting to This Configuration Only instead of All Configurations. If you forget to do this, then you will have to go to the other configuration and set it back to 6. 9. Click the Rebuild symbol (which resembles a traffic light) to show the changes before exiting the Modify dialog box. Notice that the CrvPattern2 fails after rebuilding CrvPattern1 with eight instances. Click the green check mark icon to exit the Modify dialog box, and then make the same changes to the CrvPattern2, from changing the dimension name and the number of patterned instances to eight (remember to use the This Configuration Only setting). The part should now look like Figure 10.22.
FIGURE 10.22 The model after step 9
343
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 344
Building Intelligence into Your Parts
10. Double-clicking to change configurations now shows a part with a different color and a different number of holes and ribs. After the first change between configurations, the changes should happen quickly because SolidWorks has stored the geometry. 11. Go to File ➪ Properties, and select the Configuration Specific tab. Set the Apply To dropdown list to Default, and type a Property Name of description and a Value of Gray Vent Cover. Now change the Apply To drop-down setting to Size 1 and type a description for the new configuration using the name of the color that you applied to this config. Figure 10.23 shows the two states of the data.
FIGURE 10.23 Setting the Configuration Specific custom properties
12. Exit the Custom Properties dialog box. 13. Now that you have made a few changes manually, the following steps guide you through bringing these changes into a design table and using the design table to make additional changes. From the menus, select Insert ➪ Design Table. Use Auto-create as the Source, allow model edits, and turn on all three option in the Option panel. Click OK to create the design table. Figure 10.24 shows the design table that you have automatically created.
FIGURE 10.24 The automatically created design table
344
16_080139 ch10.qxp
3/26/07
3:41 PM
Page 345
Working with Part Configurations
14. Use the striped border to move the window without closing it. This may take some practice. If the window closes, just RMB click the design table in the FeatureManager and select Edit Table. Move the window to a place where you can see the model clearly. 15. If a cell in the second row of the design table is selected, select a different empty cell that is not in the second row (this prevents data from automatically populating cells until you have the correct data). Now double-click the Extrude1 feature in the FeatureManager. Find the .500" (D1) dimension on the screen. RMB click the dimension and rename it BaseThk. 16. Click the next open cell in the second row, and double-click the .500" dimension that you just renamed. You may have to use the handles at the corners and side midpoints to resize the Excel window to see everything. Add another configuration row and the additional values in the cells, as shown in Figure 10.25. The color number is determined by a formula that you can find in the help section under the topic Color Parameter.
FIGURE 10.25 Make additions to the design table.
17. Remember that this part needs to have the number of ribs always equal to the number of holes. This is simple to do in Excel. Click in the first row value for the Rib# number. This is cell F3 in Figure 10.25. Type the equal sign, and then click in the cell to the left, E3. You can also simply type =E3 in this cell. This links the Rib# cell to the Hole# cell. 18. Use the Window Fill feature by selecting the dot at the lower-right corner of the selected F3 cell and dragging it down to also include cells F4 and F5, as shown in Figure 10.26. 19. Click in a blank space to exit the design table. Double-click through the configurations in the ConfigurationManager to see the results of your efforts.
345
10
16_080139 ch10.qxp
Part II
3/26/07
3:41 PM
Page 346
Building Intelligence into Your Parts
FIGURE 10.26 Copying the equation to other cells
Drag this handle
Summary Configurations are a powerful way to control variations of a design within a single part file. Many aspects of the part can be configured, while a few cannot. Manually created configurations are useful for making a small number of variations and a small number of configurations, but they become unwieldy when you need to make more than a few variations of either type. Design tables are recommended because they allow you to more clearly see all of the changes that have been made for all of the configurations. Having the power of Excel available allows you to access many functions that are not shown here, such as using lookup tables and Concatenate functions to build descriptions or configuration names. I will briefly revisit design tables in the section on assembly configurations to expand on the information here, and to incorporate the additional assembly configuration information.
346
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 347
Editing and Evaluation
I
f you work like I do, then you probably create a part once, but edit it many times. As I often say, design for change is really at the core of most of the modeling work that you will do in SolidWorks, and deletion is not an editing option.
IN THIS CHAPTER Using Rollback Reordering features
You do the most good — or the most harm — in the initial stages of modeling when you are setting up parametric relations between features and sketches. For this reason, editing often quickly turns into repair. Granted, some changes are simply unavoidable, but a thorough knowledge of editing — and repairing — can help you to understand the how, what, and why of modeling best practice. This chapter starts with some very basic concepts of editing, which you may have picked up if you have been reading this book from the beginning. Because this is the last chapter in Part II, and the last that deals strictly with part modeling, it also contains a summary of part-modeling best practice and a set of model evaluation tools that can help you to evaluate the manufacturability and aesthetic properties of parts. I have included these evaluation tools in a chapter on editing because the edit-evaluate cycle is one of the most familiar in modeling and design practice.
Using Rollback Rolling back a model simply means looking at the results of the design tree only up to a certain point in the model history. In SolidWorks, you can actually change history — that is, you can change the order in which operations are completed. As a result, the chronological order in which features are created is not necessarily related to the order in which these features display in the design tree, or the order in which the operations are completed.
347
Reordering folders Using the Flyout FeatureManager Part modeling best practice summary Evaluation techniques Tutorial: Editing and evaluation techniques
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 348
Building Intelligence into Your Parts
You can use several methods to put the model in this rolled-back state: n Dragging the Rollback bar with the cursor. n RMB clicking and selecting one of the Rollback options. n Editing a feature other than the last one in the design tree (SolidWorks rolls back the model automatically). n Using the Tools ➪ Options setting that allows you to control the Rollback bar with the arrow keys. n Pressing Esc during a long model rebuild. This method is supposed to roll you back to the last feature that was rebuilt when you pressed Esc; however, in practice, I have rarely seen it do this, and it usually just rebuilds the entire model anyway.
Using the Rollback bar The Rollback bar, which is usually found at the bottom of the FeatureManager in SolidWorks part documents, enables you to put the part into almost any state in the model history. This is not the same as the Undo command, but is the equivalent of suppressing everything in the FeatureManager after a certain point. Figure 11.1 shows the Rollback bar in use. Notice how the cursor changes into a hand icon when you move it over the bar.
FIGURE 11.1 Using the Rollback bar
348
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 349
Editing and Evaluation
Consumed features When you use a sketch for a feature such as a Sketch Driven Pattern, the sketch is left in the design tree, in the place where it was created. However, most other features, such as extrudes, consume the sketch, meaning that the sketch disappears from its normal order in the FeatureManager and appears indented under the feature that was created from it. Consumed sketches are sometimes also referred to as absorbed sketches.
Examining the parent-child relationship In genealogical family tree diagrams, the parent-child relationship is represented with the parent at the top, and the children branched below the parent. In SolidWorks, parent-child relationships are tracked differently. Figure 11.2 shows the difference between a genealogical family tree and the SolidWorks design tree.
FIGURE 11.2 Different interpretations of the structure of parent-child relationships
SolidWorks family tree Genealogical family tree
You can display the parent-child relations between SolidWorks features as shown in Figure 11.2 by opening the RMB menu on any feature, and selecting Parent/Child. This helps you to determine relationships before editing or deleting, so that you can see which features will be removed or go dangling.
349
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 350
Building Intelligence into Your Parts
When SolidWorks puts the child feature at the top, it is, in effect, turning the relationship upside down, but long-time users have all somehow learned to look at this without questioning it. In the SolidWorks FeatureManager, the earlier point in history is at the top of the tree, but the children are listed earlier than the parents. Once you look at it this way, you can see that SolidWorks has chosen a very unintuitive method to display the features in the tree. The method SolidWorks has chosen to use stresses the importance of solid features over other types of sketch or curve features. It appears to be even less intuitive when you think of the order in which features are created. For example, you create an extrude from a sketch, and so the sketches exist before the extrude in the FeatureManager. However, when you create the extrude, SolidWorks places the sketch underneath the extrude. In fact, this restructuring can become more apparent when a sketch (for example, Sketch1) is created early in the part history, and then not used to create a feature (for example, Extrude5) until much later. If you roll down the FeatureManager feature by feature, you arrive a point at the end of the design tree where Extrude5 appears and Sketch1 suddenly moves from its location at the top of the tree to under Extrude5 at the bottom of the tree. This scenario may cause a situation where many sketches and other features that are created between Sketch1 and Extrude5 are dependent on Sketch1, but where Sketch1 suddenly appears after all of these other features. As this example shows, the more closely you examine how the relationships are depicted, the more counterintuitive they appear. The only thing that you can do about this relationship structure is to realize that SolidWorks displays many relations upside down, and learn to understand it and not get confused in the process. In some ways, ignorance is bliss, because if you do not know that the relationships are shown in a confusing way, then it might not occur to you that there is anything wrong. One way to get around difficulties in understanding the chronological order of features when compared against the relationship order of features is to roll back a model tree item by item. This can help you sort through the issues. Also remember that from SolidWorks’ point of view, the solid feature is the most important item in the tree and is what the rest of the items in the tree are there to support. SolidWorks has made the solid features easily visible and accessible in the tree. There is a movement afoot among a group of users to try to convince SolidWorks to enable the tree to be displayed in multiple ways, one of which would be a strictly linear, chronological way. Another option would be graphically showing the hierarchical links between features, and still another would be a traditional “genealogical” tree approach. If you would like to encourage SolidWorks in one of these directions, please fill out an enhancement request.
Rolling back features with multiple parents Take an example such as a loft with guide curves. If you create the guide curves first, and then you create the loft profiles by referencing the guide curves, then the loft automatically reorders these
350
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 351
Editing and Evaluation
sketches when they display under the loft feature such that the profiles are listed in the order in which they were selected. The guide curves are also shown in the order that they were selected. This is shown in Figure 11.3. This restructuring can really be confusing, especially if you want to go back and edit any of the relationships between the sketches. It becomes even more so if the sketches have been renamed so that the names do not clearly reflect the natural order of the sketches before they were all consumed by the loft feature. You can find this example on the CD-ROM with the filename Chapter 11 Loftwgc.sldprt.
FIGURE 11.3 Multiple parents and sketch reordering
In this example, the two guide curves were created as part of a single sketch, and the SelectionManager was used to select them as individual open curves. This is why the Guide Curves sketch is represented with the contour symbol rather than a regular sketch symbol.
NOTE
Viewing consumed features in their original order If you want to view consumed sketches in their original order — for example, the sketches in the loft feature in Figure 11.3 — you must first expand the feature so that you can see the consumed sketches, and then rollback between the feature and the first sketch. At this point, a warning message appears, stating that the sketches will be temporarily unabsorbed during editing. You can then move the Rollback bar again to show the sketches. This maneuver can become complicated when you have two sketches absorbed by a projected curve, the projected curve absorbed by a composite curve, and the composite curve absorbed by a sweep feature. To isolate the original projected sketches, you need to experiment with the placement of the Rollback bar, as shown in Figure 11.4.
351
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 352
Building Intelligence into Your Parts
FIGURE 11.4 Rollback of nested, absorbed features
To view consumed sketches in their original order, follow these steps: 1. Expand the sweep. 2. Rollback between the sweep and the profile sketch. 3. Answer the prompt that appears. 4. Roll down so that you can see the unabsorbed sketches and curves. 5. Expand the composite curve. 6. Rollback to just after the composite curve. 7. Rollback so that you can see the contents of the composite curve. 8. Expand the projected curve. 9. Rollback to just after the projected curve. 10. Rollback so that you can see the contents of the projected curve.
352
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 353
Editing and Evaluation
Enhancement requests This is a great time to talk about enhancement requests. The SolidWorks Web site (www .solidworks.com) has a section for users to submit suggestions for adding new features or changing existing ones in the SolidWorks software. Users have been able to do tricky rollbacks such as this for the last three releases, but it seems evident that all of the possible ramifications of this technique have not been considered. Because changes are made on the basis of popularity, I recommend that if you are interested in seeing this functionality improved, you should submit an enhancement request for this particular function.
Other Rollback techniques The Rollback feature is available through the RMB menu. Just RMB click a feature and select either Rollback or Roll to Previous. If you are already rolled back and you RMB click below the Rollback bar, then you can access additional options to Roll Forward and Roll to End. If you have a situation with nested, absorbed features as described earlier, then selecting Rollback from the RMB menu can cause the Rollback bar to disappear and for all the features to gray out. To get out of this mode, where essentially nothing is available, you can either close out of and reload the part, or simply apply the Undo command.
CAUTION
Editing any feature other than the last feature also serves to rollback the model while you are in Edit mode. As soon as you rebuild the feature or sketch, SolidWorks rebuilds the entire design tree. The Tools ➪ Option setting for Arrow Key Navigation enables you to use the up- and down-arrow keys to manipulate the Rollback bar. Under normal circumstances, the arrow keys control the view orientation, but after you have moved the Rollback bar once using the cursor, the up- and downarrow keys control the Rollback bar. The left- and right-arrow keys have no effect on the Rollback bar. The one situation where this technique does not work as expected is when you are working on a part in the context of the assembly, with the design tree rolled back. The down arrow simply causes the Rollback bar to roll immediately to the end of the design tree.
CAUTION
New in SolidWorks 2007, you can save the model while it is still rolled back. In previous versions, you had to roll to the end of the FeatureManager before saving, and then rollback to where you were and keep working. This made working in Rollback mode fairly frustrating (if you wanted to save the model) and dangerous, as crashing without saving means potentially losing a lot of data.
NEW FEATURE
Reordering Features As you already know, feature order can make a difference in the final shape of a part. For example, this order: 1. Extrude 2. Cut 3. Fillet 4. Shell
353
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 354
Building Intelligence into Your Parts
gives you a very different part from this order: 1. Extrude 2. Shell 3. Cut 4. Fillet
The results of these different orders is shown in Figure 11.5 (The part is split and partially transparent for demonstration purposes only). You can view this part on the CD-ROM with the filename Chapter 11 Reorder.sldprt.
FIGURE 11.5 Parts that use a different feature order
On the part in the above example, it is fairly simple to reorder the Shell feature by dragging it up the design tree. As a result, the well created by the Cut feature is not shelled around (to create a tube) if the cut comes after the shell. Also, notice the effect of applying the fillets after the shell rather than before it. The corners inside the box are sharp, while the outside corners have been filleted. When you apply the fillet before the shell, fillets that have a radius larger than the shell thickness are transferred to the inside of the shell. When you are reordering the features, a symbol may appear on the reorder cursor that says that you cannot reorder the selected feature to the location you want. In this case, you may want to select the Parent/Child option from the RMB menu to investigate. Sketch relationships, feature end conditions, and faces or edges selected for features such shell, patterns, and mirror can cause relationships that prevent reordering.
354
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 355
Editing and Evaluation
If two adjacent features are to swap places, it generally does not matter whether you move one feature up the design tree or you move the other one down. However, there are isolated situations that are usually created by the nested, absorbed features discussed earlier, where one feature cannot go in one direction, but the other feature can go in the opposite direction, achieving the exact same result.
Reordering Folders There are times when, regardless of which features you choose to move and of which direction you choose to move them in, you are faced with the task of moving many features. This can be timeconsuming and tedious, not to mention being a potential source for error. To simplify this process, you can put all of the features to be moved into a single folder, and then reorder the folder. Keep in mind that the items in the folder need to be a continuous list (you cannot skip features), and you can only reorder the folder if each individual feature within the folder can be reordered. Folders are frequently used for groups of features that go together and that may be suppressed or unsuppressed in groups. You can also use folders in assemblies. Folders are frequently used for the mass of cosmetic fillet features that are often found at the end of design trees for plastic parts, or for groups of hole features.
BEST PRACTICE
To create a folder, RMB click a feature or a selected group of features and select Add to New Folder. Folders should be renamed to have a name that helps identify their contents. You can reorder folders in the same way as individual features. When you delete a folder, the contents are removed from the folder; they are not deleted. You can add or remove features to or from the folders by dragging them in or out. If a folder is the last item in the FeatureManager, the next feature that is created is not put into the folder; you must place it in the folder manually. You cannot drag features out of a folder and place them immediately after it, because they will just go back into the folder. If you want to pull a feature out of a folder and place it after the folder, then there must be another feature between the feature that you are moving and the folder. However, you can pull a feature out of the folder and place it just before the folder.
Using the Flyout FeatureManager The Flyout FeatureManager resides at the top-left corner of the graphics window, and was introduced when SolidWorks began to consolidate floating dialog boxes into the PropertyManager window. The PropertyManager goes in the same space as the FeatureManager, and is sometimes too big to allow this area to accommodate both managers in a split window. The Flyout FeatureManager enables you to select items from the design tree when the regular FeatureManager is not available. It usually appears collapsed, so that you can only see the name of the part and the part symbol. To expand it, either click the title of the active PropertyManager, or click the plus icon next to the name of the part in the Flyout FeatureManager.
355
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 356
Building Intelligence into Your Parts
If you press the C key after the flyout has been activated by the PropertyManager but is not yet expanded, a set of scroll arrows may appear, so that the flyout can only display a single feature at a time. If the FeatureManager is expanded, pressing the C key causes the Flyout FeatureManager to display right next to the regular FeatureManager. You can use the Flyout FeatureManager in parts or in the assembly. However, you cannot use the Flyout FeatureManager to suppress or rollback the tree.
CROSS-REF
Other functionality and limitations of the Flyout FeatureManager that relate to its function in assemblies can be found in Chapters 12 to 15.
You can access the settings for the Flyout FeatureManager at Tools ➪ Options ➪ FeatureManager ➪ Use Transparent Flyout FeatureManager in Parts/Assemblies.
Summarizing Part Modeling Best Practice This section is a summary of best practice suggestions for modeling parts. Best practice lists are important because they lay the groundwork for conservative usage of the software, which is helpful for new users and users who are trying to experiment with the limits of the software. I believe that it is only after you respect the rules and understand why they are so important, that you know enough to break them. However, best practice lists should not be taken too seriously. They are not inflexible rules, but conservative starting places; they are concepts that you can default to, but that can be broken if you have good reason. None of the following best practices applies all of the time, and you have my permission to break any of these rules as long as you can explain why your situation is exempt from them. n Always use unique filenames for your parts. SolidWorks assemblies and drawings may pick up incorrect references if you use parts with identical names. n Using Custom Properties is a great way to enter text-based information into your parts. Users can view this information from outside the file by using applications such as Windows Explorer, SolidWorks Explorer, and PDM applications. n Learn to sketch using automatic relations. n Use fully dimensioned sketches when possible. Splines are often impractical to fully dimension. n Limit your use of the Fixed constraint. n When possible, make relations to sketches or stable reference geometry, such as the Origin or standard planes, instead of edges or faces. Sketches are far more stable than faces, edges, or model vertices, which change their internal ID at the slightest change and may disappear entirely with fillets, chamfers, split lines, and so on. n Do not dimension to edges created by fillets, or other cosmetic or temporary features.
356
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 357
Editing and Evaluation
n Apply names to features, sketches, and dimensions that help to make their function clear. n When possible, use feature fillets and feature patterns rather than sketch fillets and sketch patterns. n Combine fillets into as few fillet features as possible; this also allows you to control fillets that need to be controlled separately, such as fillets to be removed for FEA, drawings, and simplified configurations, or added for rendering. n Create a simplified configuration when building very complex parts or working with large assemblies. n Model with symmetry in mind. Use feature patterns when possible. n Use link values or global variables to control commonly used dimensions. n Do not be afraid of configurations. Control them with design tables where there are more than a few configs, and document any custom programming or automated features in the spreadsheet. n Cosmetic features — fillets, in particular — should be saved for the bottom of the design tree. It is also a good idea to put them all together into a folder. n Use the setting at Tools ➪ Options ➪ Performance ➪ Verification on Rebuild in combination with the Ctrl+Q command to check models periodically and before calling them “done.” The more complex the model, or the more questionable some of the geometry or techniques might be, the more important it is to check the part. n Always fix errors in your part as soon as you can. Errors cause rebuild time to increase, and if you wait until more errors exist, troubleshooting may become more difficult. n Do not add unnecessary detail. For example, it is not important to actually model a knurled surface on a round steel part. This additional detail is difficult to model in SolidWorks, it slows down the rebuild speed of your part, and there is no advantage to actually having it modeled (unless you are using the model for rapid prototype or to machine a mold for a plastic part where knurling cannot be added as a secondary process). This is better accomplished by a drawing with a note. The same concept applies to thread, extruded text, very large patterns, and other features that introduce complex details. n Do not rely heavily on niche features. For example, if you find yourself creating helices by using Flex/Twist or Wrap instead of Sweep, then you may want to rethink your approach. In fact, if you find yourself creating a lot of unnecessary helices, then you may want to rethink this approach as well, unless there is a good reason for doing so. n File size is not necessarily a measure of inefficiency. n Be cautious about accepting advice or information from Internet forums. If you are the CAD Administrator for a group of users, you may want to incorporate some best practice tips into standard operating procedures for them. The more users that you have to manage, the more you need to standardize your system.
357
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 358
Building Intelligence into Your Parts
Using the Skeleton or Wide Tree Approach
S
olidWorks is not the first parametric modeler to challenge the linear logic of genealogical analysis. The users of software like Pro/ENGINEER are responsible for developing many of the concepts and best practice techniques that SolidWorks users use today. The term Skeleton in Pro/ENGINEER has a different significance than the way it is being used here. SolidWorks does not have any feature or function named “skeleton.” The term is just being used to refer to a set of sketches, planes, axes, and reference points used to lay out the major faces and features of a part.
NOTE
The SolidWorks Help files, tutorials, and training curricula have encouraged users in some respects to take a “fast and loose” approach to modeling, which lends itself best to simple models that are not changed frequently. Little thought was given to the structure of the part; the only thing that really mattered was the final shape. The main consideration seemed to be the simplest way to do something, or how it could be done rather than how it should be done. This mentality fit well with the initial several releases of the SolidWorks software, which at that time was marketed as being simple and fast. The software has progressed immensely since those days. It is now entirely plausible to create complex castings and plastic parts with many hundreds of features, weaving in and out of surface and solid techniques, multibodies, and external references. This is a far cry from the typical tutorial or training part, which still tend to have fewer than 15 features, half of which may be fillets. With the simpler parts, you hardly give a thought to parent/child relationships, rebuild times, or the consequences of making changes that cause a feature to fail, because the whole part could be rebuilt from scratch in ten minutes anyway. This is because the people who knew the software best were doing brief sales demo vignettes and small models that could be finished before the students fell asleep. SolidWorks users have traditionally been taught to build each feature linearly, on top of the one that came before. This is the genealogical equivalent of each generation having a single child, and then that child having a single child, and so on. The family tree, or FeatureManager, winds up looking like a long staircase, with each generation related only to the generation immediately before it. In the SolidWorks world, this creates long, linear, daisy-chained relationships between consecutive features. It turns out that even though this has been hailed as the pinnacle of associative, parametric, historybased modeling, it is not really such a great idea, especially as the parts begin to get more complex. When each feature is dependent upon the one before it, all of the features must be solved in a particular order, and if one feature fails, so do all of the features that come after it. This also slows down the rebuilding process. Especially as we move into the age of parallel multi-threaded processing, a linear set of commands or features must be executed in order one after the other, and there is really no room for parallel processes. The sophistication of the documentation provided with SolidWorks software has not kept pace with the sophistication of the software itself, which I suppose is why you are reading this book rather than the help files. The documentation is still based on the simple scenarios, and the advanced user is left to figure things out on his or her own.
358
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 359
Editing and Evaluation
As the software gets more sophisticated, the models created with the software can get more sophisticated, and our methods used to build the models must also get more sophisticated. We must leave the linear modeling approaches behind. Rather than using a linear daisy-chain modeling scenario, it is better practice to base features on entities that are less likely to fail or change in such a way that dependent downstream features also fail. In earlier chapters, it has already been suggested that sketch relations should be made to other sketches when possible instead of model edges for this very reason. Taking that scenario one step further, what if a handful of sketch and plane features were used to centralize control of all of the rest of the features? What if every feature, to the extent possible, related back to these “skeleton” features? Features such as fillets, shell, and draft by design require selections from solid geometry, but other features, such as any feature created from sketches, could be made with only reference to those original skeleton sketches and planes. The parent/child relationship would look very different for a model made in this way. Instead of looking like a long staircase, this tree would look more like a tree that gets wide very quickly. There would be fewer “generations,” but each generation would be more populated. The first thing to notice is that errors in features at the top of the tree do not cascade down the tree as they do in the “stairstep” model. Secondly, it is always much easier to find how a model is constructed, because all the reference geometry used to build it is set up in the first few features. This scenario also has the potential to make better use of multi-threaded processing because the logic is less linear and more parallel.
Using Evaluation Techniques You can use evaluation techniques to evaluate geometry errors, demonstrate the manufacturability of a given part, or to some degree to quantify aesthetic qualities of a given part, or section of a part. I discuss evaluation techniques here because the design cycle involves iterations around the combination of evaluate-edit-evaluate functions. I discuss the following techniques in this section: n Draft analysis n Thickness analysis n Undercut detection n Verification on Rebuild n Check n Zebra Stripes/RealView/Lights and specularity n Curvature display n Deviation analysis n Tangent edges as phantom n CosmosXpress n MoldflowXpress
359
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 360
Building Intelligence into Your Parts
Many of these techniques apply specifically to plastic parts and complex shapes, but even if you do not become involved in these areas of design or modeling, these tools may help you to find answers on other types of products as well.
Draft analysis The SolidWorks Draft Analysis tool is a must when working with plastic parts. The part shown below has many of the situations that you are going to encounter in analyzing plastic parts. The Draft Analysis tool has four major modes of operation: n Basic n Gradual Transition n Face Classification n Find Steep Faces
Basic draft analysis The Basic draft analysis (with no options selected) simply colors faces red, green, or yellow. Colors may display transitioning if the draft shifts between two classifications. This transition type is shown in Figure 11.6 in the image to the right. For a clearer view of this method, you can find the part, Chapter 11 Draft Analysis.sldprt, on the CD-ROM.
FIGURE 11.6 Basic draft analysis results
360
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 361
Editing and Evaluation
You can perform all types of draft analysis in SolidWorks by selecting a reference flat face or plane, and setting a minimum allowable angle. In Figure 11.6, all walls have at least a one-degree draft, except for the rounded edge shown in the image to the right and the dome. Both of these shapes transition from an angle less than one degree to an angle greater than one degree. This basic analysis is good for visualizing changes in draft angle, but it also has some less desirable properties, which will become apparent as you study the other types of draft.
Gradual Transition Although the Basic analysis is able to show a transitioning draft, the Gradual Transition draft analysis takes it a step further. With the Gradual Transition, you can specify the colors. It is also useful because it can distinguish drafts of different amounts by color. It may be difficult to tell in the grayscale image in Figure 11.7, but the ribs, which were created at one degree, have a slightly different color than the floor of the part, and the walls also have a different color. Notice that cavity and core directions have different colors, as well. You may want to open this part in SolidWorks, recreate the settings, and run the analysis so that you can see the actual colors.
FIGURE 11.7 The Gradual Transition draft analysis
361
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 362
Building Intelligence into Your Parts
Some problems arise when you use this display mode, the first being the flat, non-OpenGL face shading that is used to achieve the transitioning colors. This often makes it difficult to distinguish curved faces, and faces that face different directions. The second problem is that you cannot tell that the boss on top of the dome has absolutely no draft. In fact, there is no way to distinguish between faces that lean slightly toward the cavity and faces that lean slightly toward the core. The third problem is the strange effect that appears on the filleted corners. The corners were filleted after you applied the draft and before the shell, and so the filleted corners should have exactly the same draft as the sides; however, from the color plot, it looks to be a few degrees more.
CAUTION
Software can sometimes interpret things differently from the way that a person does. As a result, any computer analysis must be interpreted with common sense.
Due to this and some of the other problems that I mentioned above, I would use the Gradual Transition draft analysis in conjunction with one of the other tests. Gradual Transition gives an interesting effect, but it is not a reliable tool for determining on its own whether or not a part can be manufactured.
Face Classification Face Classification draft analysis groups the faces into classifications using solid, non-transitioning colors. You will notice a big difference between the coloration of the Face Classification draft analysis faces and of the Basic or Gradual Transition faces. Face Classification uses OpenGL face shading, which is the same as that used by SolidWorks by default. This allows better shading and differentiation between faces that face different directions. The Basic Analysis coloration looks like all of the faces are painted the same flat hue, regardless of which direction they are facing, which makes shapes more difficult to identify. The non-Open GL alternate shading method makes it possible to display a transition in color. SolidWorks OpenGL shading cannot do this. Another advantage of using the OpenGL shading is that the face colors can remain on the part after you have closed the Draft Analysis PropertyManager. Face Classification draft analysis also adds a classification that is not used by the Basic draft analysis. Straddle Faces refer to faces that straddle the parting line, or faces that, due to their curvature, pull from both halves of the mold. These are faces that need to be split. On this part, a straddle face is shown in Figure 11.8. The light bulb icons to the left of the color swatches enable you to hide faces by classification. This is useful when you are trying to isolate certain faces, or visualize a group of faces in a certain way. This can be an extremely useful feature, especially when you have a very complex part with a large number of faces, some of which may be small and easily lost in the mix with other larger faces. The face counts that appear in the color swatches are a very helpful feature that is absent from the Basic draft analysis.
362
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 363
Editing and Evaluation
FIGURE 11.8 Face Classification draft analysis and a straddle face
Straddle face
I prefer Face Classification draft analysis because it is the clearest. If I need additional detail regarding other types of faces, then I may run a Steep Face draft analysis as a supplement. The best practice here is not that you follow my favorite type of draft analysis, but that you understand what you need to know and then use the appropriate tools to find this information. This may include running multiple analyses to collect all of the necessary information.
BEST PRACTICE
Find steep faces A steep face is defined as a face that transitions from less than the minimum angle to more than the minimum angle. Steep faces are different from straddle faces in that straddle faces are actually positive and negative, while steep faces are either entirely positive or entirely negative. On this part, the dome inside the part is classified as a steep face, as shown in Figure 11.9. If you click out of either the Face Classification or the Find Steep Faces draft analyses, then you are given the option to save the face colors. I find this useful when I am making edits to add draft or move a parting line on a plastic part. However, the problem comes when trying to switch back to the regular part colors. In the past, the best way to do this was with a macro, although some users would also try to select all of the faces and remove the colors.
363
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 364
Building Intelligence into Your Parts
FIGURE 11.9 A steep face
Steep face
New in SolidWorks 2007 sp1 (it was not available in sp0) is the Remove All Colors option in the Colors and Optics PropertyManager, as shown in Figure 11.10. With nothing selected in the selection box, just click the Remove All Colors button; SolidWorks removes all face, feature, and body colors and sets them back to the part color.
NEW FEATURE
FIGURE 11.10 The Remove All Colors option
364
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 365
Editing and Evaluation
Thickness Analysis Thickness Analysis is part of the SolidWorks Utilities, which are part of SolidWorks Office or higher. After you have activated the Utilities add-in (Tools ➪ Add-ins ➪ SolidWorks Utilities), Thickness Analysis appears under the Utilities menu. You can run Thickness Analysis in two modes, Show Thin Regions and Show Thick Regions. Of these, Show Thick Regions is the most versatile.
Show Thin Regions The Show Thin Regions option, or the “Thinness” Analysis, requires you to input a minimum acceptable thickness. Every face with a thickness above this value is turned a neutral gray, and every face with a thickness below this value is displayed on a graduated scale. Figure 11.11 shows the PropertyManager for this analysis and its result on the same part used for the draft work in the previous sections.
FIGURE 11.11 Results of the Thinness Analysis
One of the things to watch out for here is that some anomalies occur when you apply this analysis to filleted faces. The faces that are shown as colored were created by the Shell feature, and should be exactly .100 inches thick. However, it does correctly represent the undercut on the end of the part and the thickness of the ribs. A nice addition to this tool would be the identification of minimum thickness faces. Perhaps you can submit another enhancement request.
365
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 366
Building Intelligence into Your Parts
Show Thick Regions The Show Thick Regions option works a little differently from Show Thin Regions. You need to specify an upper thickness limit value, beyond which everything is identified as too thick. In these examples, the nominal wall thickness of the part is shown as .100 inches, and the thick region limit is set to .120 inches. For this type of analysis, the color gradient represents the thicknesses between .100 inches and .120 inches, while in the Thinness Analysis, the color gradient represents the values between .100 inches and 0 inches. Figure 11.12 shows how this analysis produces some anomalous results, especially at the corners, and also in the middle. Again, this is a useful tool, if not completely accurate. You can use it to find problem areas that you may not have considered, but you should certainly examine the results critically.
FIGURE 11.12 Results of the Thickness Analysis
The Treat Corners As Zero Thickness option should always be on. I have never seen a situation where turning it off improved the results; in fact, I have found that turning it off has always made corners and fillets behave worse.
366
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 367
Editing and Evaluation
This feature can generate a report, which to some extent answers questions about how or why it classifies faces in the way it does. To get a complete picture of the situation, it may be useful to look at the report when you are using the results to make design or manufacturing decisions. A sample of the report is shown in Figure 11.13.
FIGURE 11.13 A sample of a Thickness Analysis report
Undercut Detection The Undercut Detection tool is conceptually flawed in that it gives incorrect results every time. However, if you think of the labels as being changed slightly, the results become partially usable. Even if you and your mold builder know that a part has absolutely no undercuts, the Undercut Detection tool will nonetheless always identify all of the faces to be undercut. In fact, the only faces that this tool will identify as not undercut are faces that have no draft on them. The only time it correctly identifies an undercut is when it classifies the undercut as Occluded Undercut. Faces that have no draft and are occluded undercut are improperly identified as simply No Undercut. You may want to avoid this tool because too much interpretation of incorrect results is necessary; however, if you still want to use it, then here is a translation guide that may help: n Direction 1 Undercut — should read — Pull from Direction 2 n Direction 2 Undercut — should read — Pull from Direction 1
367
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 368
Building Intelligence into Your Parts
n Straddle Undercut — should read — Straddle faces n No Undercut — should read — No draft in the primary draft direction, but may be occluded undercut faces n Occluded Undercut — should read — Occluded Undercut faces that have draft in the completely irrelevant primary draft directions; does not include occluded undercut faces that have no draft in the primary direction Figure 11.14 shows the PropertyManager for this function and the results. If you would like to test it for yourself, the part is on the CD-ROM with the filename Chapter 11 Draft Analysis.sldprt.
FIGURE 11.14 The results of the Undercut Detection tool
Verification on Rebuild Verification on Rebuild is an option that you can access through Tools ➪ Options ➪ Performance ➪ Verification On Rebuild. Under normal circumstances (with this setting turned off), SolidWorks checks each face to ensure that it does not overlap or intersect improperly with every adjacent face. Each face can have several neighbors. This option is shown in Figure 11.15.
368
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 369
Editing and Evaluation
FIGURE 11.15 The Verification on Rebuild option
With the setting turned on, SolidWorks checks each face with every other face in the model. This represents a slightly better check than with the setting off, and a greatly increased workload. The switch is off by default to prevent rebuild times from getting out of control. For most parts, the default setting is sufficient; however, when parts become complex, you may need to select the more advanced setting. If you are having geometry or rebuild error problems with a part and cannot understand why, then try turning Verification on and pressing Ctrl+Q. Ctrl+Q applies the Forced Rebuild command, and rebuilds the entire design tree, whether or not SolidWorks determines that it is needed. Ctrl+B, or the Rebuild command, only rebuilds what SolidWorks determines needs to be rebuilt. If you see additional errors in the design tree that were not there before, then the combination of Verification on Rebuild and Forced Rebuild has worked. If not, then your problem may be elsewhere. You still need to fix any errors found this way. For speed reasons, it is normal practice to turn Verification On Rebuild off, and to use it selectively to check models with potential errors. The type of speed degradation that you can see is in the 10-percent to 60-percent range. Some of the performance degradation as relates to patterns is documented in Chapter 8.
PERFORMANCE
Check Check is a tool that checks geometry for invalid faces and other similar geometry errors. It is also often used to find open edges of surface bodies, short edges, and the minimum radius on a face or entity. I usually apply the Check tool before turning on the Verification on Rebuild option. The Check tool points to specific geometry (not features or sketches, but 3D face geometry) that is the cause of the problem. When it finds general faults, the faults are often displayed in threes, and the locations that the Check tool points to may or may not have something obvious to do with a possible fix. Much of the time, the best tool for tracking down geometry errors is the combination of experience and intuition. It is not very scientific, but you come to recognize where potential problems are likely to arise, such as attempting to intersect complex faces at complex edges. Figure 11.16 shows the Check Entity dialog box.
369
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 370
Building Intelligence into Your Parts
FIGURE 11.16 The Check Entity dialog box
Reflective techniques Evaluating complex shapes can be difficult. Subjective evaluation is typically personal, and requires an eye for the type of work you are doing. Objective evaluation requires some sort of measurable criteria for determining a pass or fail, or it enables you to assign a score somewhere in the middle. One way to subjectively evaluate complex surfaces, and in particular the transitions between surfaces around common edges, is to use reflective techniques. If you look at an automobile’s fender, you can tell whether it has been dented or if a dent has been badly repaired by seeing how the light reflects off of the surface. The same principle applies when evaluating solid or surface models. Bad transitions appear as a crease or an unwanted bulge or indentation. The goal is to turn off the edge display and not be able to identify where the edge is between surfaces, for the transition to be as smooth as if the whole area were made from a single surface.
Zebra Stripes Zebra Stripes can be activated in one of two ways, through the menus at View ➪ Display ➪ Zebra Stripes, or from a toolbar button on the View toolbar. The technique that was really made for analyzing complex shapes is Zebra Stripes. This places the part in a room that is either spherical or cubic, where the walls are painted with alternating black-and-white stripes (although you can change the colors and the spacing of the stripes). The part is made to be perfectly reflective, and the way that the stripes transition over edges tells you something about the qualities of the faces on either side of the edge. Four conditions are of particular interest: n c0 = faces contact at edge n c1 = faces are tangent across edge
370
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 371
Editing and Evaluation
n c2 = curvature of each face is equal at the edge and the transition is smooth n c3 = rate of change of curvature of each face is equal at the edge The Zebra Stripes tool can only help you identify c0, c1, and c2, and only subjectively. This feature is of most value between complex faces. Figure 11.17 illustrates how the Zebra Stripes tool shows the differences between these three conditions.
FIGURE 11.17 Contact, tangency, and curvature continuity
Original faces with Zebra Stripes Original surfaces
Original faces with the edge filleted to be tangent
Original faces with curvature continuous blend between the faces
Notice how on the Contact-only model, the Zebra Stripe lines do not line up across the edge. On the Tangent example, the stripes line up across the edges, but the stripes themselves are not smooth. On the Curvature Continuous example, the stripes are smooth across the edges. The part shown in Figure 11.17 is a surface model, and can be found on the CD-ROM with the filename Chapter 11 Zebra Stripes.sldprt. You should rotate the model a lot when you are using the Zebra Stripes tool. Changing the density of the lines can also help, as can increasing the image quality (Tools, Options, Document Properties, Image Quality). Turning off the edge display may also help.
TIP
371
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 372
Building Intelligence into Your Parts
RealView RealView Graphics display is only available to users with certain types of video cards. To see whether your card supports RealView, check the SolidWorks Web site. RealView causes reflections that can be used in a way similar to the reflections in Zebra Stripes. Rotate the part slowly and watch how the reflections flow across edges.
Lights and specularity If the other methods are not working for you, then you can also try to use simple lights with the specularity turned up. This does not work as nicely as the highly reflective Zebra Stripes and RealView techniques, but the bright spots created by the specularity settings for lights can give similar results for evaluating the quality of transitions between faces.
Curvature display Model curvature can be plotted onto the model face using colors, as shown in Figure 11.18. The accuracy of this display leaves a bit to be desired, but it does help you to identify areas of very tight curvature on your part. Areas of tight curvature can cause features such as fillets and shells to fail.
FIGURE 11.18 Curvature display
Deviation Analysis Deviation Analysis measures how far from tangent the surfaces on either side of a selected edge actually are. For example, the edges shown in Figure 11.19 are found to be fair, but not very good. I prefer deviations of less than 0.5 degrees. Often with some of the advanced surface types such as Fill, Loft, and Boundary, SolidWorks can achieve edges with less than 0.05-degree maximum deviation.
372
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 373
Editing and Evaluation
FIGURE 11.19 An example of Deviation Analysis
While Deviation Analysis helps to quantitatively measure how close to tangent the faces on either side of the selected edge are, you must still run Zebra Stripes to get the complete picture of the flow between faces. Both tests have to return good results to have an acceptable face transition.
Tangent Edges as Phantom Using the Tangent Edges as Phantom setting is an easy way to evaluate a large number of edges all at once. This feature does not do what the Zebra Stripes tool does, but it gives you a good indication of the tangency across a large number of edges. Although this is an easy method to use, it is not completely reliable. I have not seen this function deliver false positives (edges displayed as tangent when in fact they were not), but I have seen many false negatives (edges that display as non-tangent when in fact they were). Figure 11.20 shows a situation where the edges are displayed with solid edges, but Deviation Analysis shows them to have a zero-degree maximum deviation.
FIGURE 11.20 Using the Tangent Edges as Phantom setting
373
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 374
Building Intelligence into Your Parts
COSMOSXpress COSMOSXpress is a limited version of CosmosWorks that is bundled with SolidWorks to acquaint users with finite element analysis, or FEA. The full version of CosmosWorks does a wide range of analysis, from vibrations to large deformations. COSMOSXpress is a very quick and easy wizard for simple stress analysis on standalone parts with simple constraints. It does simple linear stress analysis on a single part with a single material using only fixed constraints. You can also use COSMOSXpress to do a simple stress/weight optimization based on dimensions that you select to be altered. You can start COSMOSXpress through the Tools menu. The interface guides you through a very simple wizard. If you have any familiarity with FEA applications, you will find COSMOSXpress easy to understand and use.
Material The first step in running a simple analysis is to assign a material. The list of materials for COSMOSXpress is limited, compared to the full product. Once you have made your selection, click Apply. Figure 11.21 shows some of the materials selection.
FIGURE 11.21 Assigning a material in COSMOSXpress
The material assigned through the COSMOSXpress interface is applied as a SolidWorks material, complete with RealView, if applicable.
Restraint You can apply restraints to the part. The restraints are limited to Fixed for the faces that are selected. Figure 11.22 shows the interface and the restraint symbols on the part.
374
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 375
Editing and Evaluation
FIGURE 11.22 Applying restraints
Load You can apply loads to faces as force or pressure. You can also select multiple faces. Figure 11.23 shows loads that are applied on the sample part.
FIGURE 11.23 Applying a load
Analyze The analysis automatically takes care of the mesh. An animation plays as the analysis runs. This is shown in Figure 11.24.
375
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 376
Building Intelligence into Your Parts
FIGURE 11.24 Analyzing the model
Results The results that can be shown are the stress distribution, the displacement distribution, and the deformed shape of the model. A stress plot is shown in Figure 11.25. You can use a number of good ways to export the results, including as eDrawings, AVI, and HTML.
FIGURE 11.25 A Stress plot for the analysis
376
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 377
Editing and Evaluation
Optimization Optimization takes a single dimension and varies it to try to achieve the best stress-to-weight ratio. As shown in Figure 11.26, the gussets have been made smaller to reduce weight and to keep the Factor Of Safety above 4.
FIGURE 11.26 Optimization results
MoldflowXpress MoldflowXpress uses the same concept as COSMOSXpress in that a limited version of the high-end software is bundled into SolidWorks, but it applies to software that predicts moldability of plastic parts, rather than to stress analysis. Also in keeping with the other software, MoldflowXpress is very easy to use, contains a wizard to guide you, and requires no real mold expertise to run. Although the software is easy to run, in order for you to be able to interpret the results, you have to know a little bit about what you are doing. The two Xpress products do not automatically solve all of your problems regarding FEA and Moldflow analysis. While the wizard interfaces remove most of the expert-level knowledge that is needed to navigate it, setting up the problem and interpreting the results do require some background knowledge.
Injection location To start a MoldflowXpress analysis, you need to determine the injection location. You are only allowed a single gate, and the analysis is set up to assume that the runner is on the other side of the gate; as a result, this is a single-cavity, single-gate analysis, as shown in Figure 11.27.
377
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 378
Building Intelligence into Your Parts
FIGURE 11.27 Selecting an injection location
Material The second step is to establish the material. Again, the Xpress product has a limited selection set, but most of the major families are represented in the selections. Material selection is shown in Figure 11.28.
FIGURE 11.28 Material selection
Conditions The Conditions tab enables you to adjust the melt temperature and the mold temperature. Default temperatures are probably best, unless you know what you are doing.
378
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 379
Editing and Evaluation
Disabling the Automatic Injection Time option can enable you to get a short shot, which is considered a bad thing in real molding; however, in simulation, it can give you some idea of what the flow front is doing — how the liquid plastic is filling the mold, which areas fill first, last, and so on. Figure 11.29 shows this part of the wizard interface.
FIGURE 11.29 The Conditions tab
Analyze and Results The mold-filling results take a bit longer than the FEA results. MoldflowXpress gives you a general statement about the moldability of your part (in this case, Figure 11.30 shows that it is acceptable), the fill time for the cavity, and a colored fill-time plot showing how long it takes to fill the various areas of the part.
FIGURE 11.30 The Results tab
379
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 380
Building Intelligence into Your Parts
Tutorial: Making Use of Editing and Evaluation Techniques Using this tutorial, you make some major edits to an existing part. You use some simple loft and spline commands, and work with the rollback states and feature order, as well as some evaluation techniques. Please follow these steps: 1. Open the existing part with the filename Chapter 11 Tutorial Start.sldprt. Roll the part back and step through it feature by feature to see how it was made. Edit the loft feature to see which sketches were used to create it. This can help you to understand how the part was built. Exit the loft command and move the rollback bar back to the bottom of the tree. 2. Start the Deviation Analysis tool (Tools ➪ Deviation Analysis). Select the edges, as shown in Figure 11.31.
FIGURE 11.31 Deviation analysis of an existing part
Select RMB then select tangency
The maximum deviation is about ten degrees, which is far too much. This part needs to be smoothed out, which you can do using splines in place of lines and arcs. 3. The first step is to make the outlet all one piece with the spiral. You can do this with a Fit Spline. You need to create the Fit Spline before the loft profiles and after the spiral.
Expand the loft, and rollback between the loft feature and the first sketch. Answer OK to the prompt, and then rollback to just after the spiral, as shown in Figure 11.32.
380
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 381
Editing and Evaluation
FIGURE 11.32 Rolling back to just after the spiral
4. RMB click the spiral in the FeatureManager and show it. Open a new sketch on the Top plane. 5. Try to draw a horizontal line from the outer end of the spiral. You will notice that you cannot reference the end of the spiral. Curves that are absorbed into other features are notoriously difficult to work with. Generally, you need to select them from the FeatureManager to do anything at all with them. Also, if you need to reference an end of an absorbed curve, you are better off using Convert Entities to make it into a sketch entity.
TIP
6. Notice that you cannot select the spiral from the graphics window. Even when selected from the FeatureManager, it appears not to be selected in the graphics window. Ensure that it is selected in the FeatureManager, and then click the Convert Entities button on the sketch toolbar. 7. Draw a horizontal line from the outer end of the spiral and dimension it to be three inches long, as shown in Figure 11.33. 8. Select both the converted spiral and the line, and click Tools ➪ Spline Tools ➪ Fit Spline. Set the Tolerance to .1 and make sure that only the Constrained option is selected. Click OK to accept the Fit Spline. Test to make sure that a single spline is created by moving your cursor over the sketch to see if the whole length is highlighted.
NOTE
The Fit Spline feature fits a spline to a set of sketch entities within the specified tolerance. It can be a useful tool for smoothing out sketch geometry.
CAUTION
Do not exit the Fit Spline by pressing the Enter key as you do with other commands, because it simply exits you out of the command without creating a spline.
381
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 382
Building Intelligence into Your Parts
FIGURE 11.33 Preparing for the Fit Spline
9. Exit the sketch, and create a new plane. Click Insert ➪ Reference Geometry ➪ plane. Select the Parallel Plane At Point option. Select the Right plane from the Flyout FeatureManager and the outer end of the Fit Spline that you have just created. Click OK to accept the new plane. This is illustrated in Figure 11.34.
FIGURE 11.34 Creating a new plane
382
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 383
Editing and Evaluation
10. Drag the Rollback bar down between Sketch3 and Loft1. If it goes beyond Loft1, then you need to navigate back to this position again. 11. RMB click Sketch3 and select Edit Sketch Plane. Select the newly created Plane1 from the Flyout FeatureManager, and click OK to accept the change. 12. Notice that the loft profile has moved to a place where it does not belong. This is because the sketch has a Pierce constraint to the spiral, and there are multiple places where the spiral pierces the sketch plane.
Edit Sketch3 and delete the Pierce constraint on the sketch point in the middle of the construction line. Create a Coincident relation between the sketch point and the outer end of the Fit Spline, as shown in Figure 11.35. Do not exit the sketch.
FIGURE 11.35 Sketch3 in its new location
13. One of the goals of these edits is to smooth out the part. Remember that the Deviation Analysis told us that the edges created between the lines and arcs in Sketch3 were not very tangent. For this reason, it would be a good idea to replace the lines and arcs in Sketch3 with another Fit Spline.
RMB click one of the solid sketch entities in Sketch3, and click Select Chain. 14. Create another Fit Spline using the same technique as in Step 8. Exit the sketch. 15. Drag the Rollback bar down one feature so that it is below the Loft. Notice that the Loft feature has failed. If you hold the cursor over the feature icon, the tooltip confirms this by displaying the message, “The Loft Feature Failed to Complete.”
383
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 384
Building Intelligence into Your Parts
16. Edit the Loft feature. Expand the Centerline Parameters panel if it is not already expanded, and delete the Spiral from the selection box. In its place, select the Spiral Fit Spline. 17. If the loft does not preview, check to ensure that the Show Preview option is selected in the Options panel, at the bottom. 18. If it still does not preview, RMB click in the graphics window and select Show All Connectors. Position the blue dots on the connector so that it looks like Figure 11.36.
FIGURE 11.36 Positioning the connectors
Position connector dots in approximately corresponding locations on the two loft profiles
19. Click OK to accept the loft. The loft should be much smoother now than it was before. In addition, the spiral feature should no longer be under the loft, and should now be the first item in the design tree.
384
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 385
Editing and Evaluation
20. Drag the Rollback bar down to just before the Shell feature. Notice that Fillet5 has failed. Move the mouse over Fillet5. The tooltip tells you that it is missing some references. Edit Fillet5 and select edges in order to create fillets, as shown in Figure 11.37.
FIGURE 11.37 Repairing Fillet5
Make selections to fillet edges
21. RMB click in the design tree and select Roll To End. This causes the FeatureManager to become unrolled all the way to the end. 22. The outlet of the involute is now longer than it should be. This is because the original extrude was never deleted from the end. RMB click the Extrude1 feature and select Parent/Child. The feature needs to be deleted, but you need to know what is going to be deleted with it. 23. The Shell is listed as a child of the extrude because the end face of the extrude was chosen to be removed by the Shell. Edit the Shell feature and remove the reference to the face. (A Shell feature with no faces to remove is still hollowed out.) 24. If you RMB click Extrude1 and select Parent/Child again, the Shell feature is no longer listed as a child. 25. Delete Extrude1, and when the dialog box appears, press Alt+F to select Also Delete Absorbed Features. 26. Edit the Shell feature and select the large end of the loft. Exit the Shell feature. The results up to this step are shown in Figure 11.38.
385
11
17_080139 ch11.qxp
Part II
3/26/07
3:44 PM
Page 386
Building Intelligence into Your Parts
FIGURE 11.38 The results up to step 26
27. Drag a window in the design tree to select the four fillet features. Then RMB click and select Add to New Folder. Rename the new folder Fillet Folder. 28. Click the Section View tool, and create a section view using the Front plane. 29. Reorder the Fillet folder to after the Shell feature. 30. At this point, you should notice that something does not look right. This is because creating the fillets after the Shell causes the outside fillets to break through some of the inside corners. The fillets should have failed, but have not, as shown in Figure 11.39.
FIGURE 11.39 Fillets that should have failed
386
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 387
Editing and Evaluation
31. Go to Tools ➪ Options ➪ Performance, and turn on Verification on Rebuild. Then click OK to exit the Tools, Options, and press Ctrl+Q. The fillets should now fail. 32. Click Undo to return the feature order to the way it was. 33. Save the part.
Summary Working effectively with feature history, even in complex models, is a requirement for working with parts that others have created. When I get a part from someone else, the first thing that I usually do is to look at the FeatureManager, and roll it back if possible to get an idea of how the part was modeled. Looking at sketches, relations, feature order, symmetry, redundancy, and so on are important steps in being able to repair or edit any part. Using modeling best practice helps to ensure that when edits have to be done, they are easy to accomplish, even if they are done by someone who did not build the part. Evaluation techniques are really the heart of editing, as you should not make too many changes without a basic evaluation of the strengths and weaknesses of the current model.
387
11
17_080139 ch11.qxp
3/26/07
3:44 PM
Page 388
18_080139 pt03.qxp
3/26/07
3:48 PM
Page 389
Working with Assemblies IN THIS PART Chapter 12 Organizing Assemblies Chapter 13 Getting More from Mates Chapter 14 Assembly Configurations and Display States Chapter 15 Component Patterns Chapter 16 Modeling in Context
18_080139 pt03.qxp
3/26/07
3:48 PM
Page 390
19_080139 ch12.qxp
3/26/07
3:52 PM
Page 391
Organizing Assemblies
C
hapter 5 offered a brief introduction to the basics of assemblies, how to put parts together, the basics of mating, and so on. The basic process for putting assemblies together remains the same for assemblies of any size, but once the assembly passes a certain point — and this point is likely different for each user or application — the assembly will benefit from some sort of organization or management techniques. This chapter introduces you to the tools and techniques that are available to help you manage performance issues as well as general browse-worthiness or searchability.
IN THIS CHAPTER Identifying the elements of an assembly Using subassemblies Using folders Working with tree display options
Identifying the Elements of an Assembly From Chapter 5, you know that an assembly has parts and mates. However, the simple tutorial in Chapter 5 did not go beyond this. While this tutorial got you started, it did not provide enough information to make you competent with assemblies. Real-world assemblies can become very complex. As the assembly grows in the number of parts and design requirements, you may need to add some of the following types of assembly elements (you may already be familiar with some of these parts from having worked with part documents): n Assembly equations n Assembly layout sketch n Assembly reference geometry (plane, axis, point, coordinate system) n Parts
391
Tutorial: Managing the FeatureManager
19_080139 ch12.qxp
Part III
3/26/07
3:52 PM
Page 392
Working with Assemblies
n Subassemblies n Folders for parts n Folders for mates n Mates n Assembly features (cuts that are made once the parts are assembled) n Component patterns n In-context reference placeholders n Smart Fasteners n Smart Components n Hole Series These elements are shown in Figure 12.1.
FIGURE 12.1 Elements of an assembly
392
19_080139 ch12.qxp
3/26/07
3:52 PM
Page 393
Organizing Assemblies
Standard reference geometry items The three standard planes and the Origin are all familiar to you in the assembly FeatureManager design tree, as are the other standard items, such as the Annotations, Design Binder, and Lights and Cameras folders. These items offer the same standard functionality of their part document counterparts.
Assembly equations Assembly equations work mainly like part equations, but with some additional complications and considerations. For example, one of the additional features of assembly equations is the ability to drive the dimensions of one part from another part. The syntax is slightly different for this application, as shown in Figure 12.2. Overall, issues with equation order and using driven dimensions on the right side of the equation are the same between parts and assemblies.
CROSS-REF
Equations are discussed in detail in Chapter 9.
FIGURE 12.2 An assembly equation driving one part from another
External references Notice the “->” symbol after the Equations folder in the Assembly FeatureManager. This means that there is an external or in-context reference.
CROSS-REF
In-context references are discussed in depth in Chapter 16.
When one part drives another part in this way, the assembly must also be open to drive the relationship. If just the two parts are open individually, then changing the driving part does not update the driven part; because the relationship was created in the context of the assembly, the assembly must also be open to facilitate the change.
Link values and global variables Link values and global variables also work in assemblies, but they do not work between parts. Local assembly sketches can use these functions, and the parts can use them when edited in the context of the assembly, but they cannot cross any document barriers (links must remain within a single document).
Renaming In past versions of SolidWorks, assembly equations had a hard time keeping track of parts when they were renamed, but in SolidWorks 2007, equations update regardless of how the part is
393
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 394
Working with Assemblies
renamed. This is also true of renaming the assembly. This includes renaming a part using the Save As command, using SolidWorks Explorer, or using Windows Explorer. It also includes redirecting the assembly to the new part name, as well as renaming the assembly using each of these techniques. If the assembly can find the part and recognizes the part as the one that it is looking for, then the equation will work. The methods named above for renaming parts are not recommended; for testing purposes I was specifically trying to break the relationships in the equations.
Recommendations While assembly equations are certainly a valid way to control part sizes, I would recommend using assembly or part configurations, possibly with design tables, to accomplish something similar.
CROSS-REF
Assembly configurations are discussed in Chapter 14. Design tables are discussed in Chapter 10.
You may have unexpected results if a single dimension is controlled from more than one location. For example, if you have a part-level equation and an assembly-level equation, then one of the equations will be automatically set to Read Only and will not be used.
CAUTION
Assembly layout sketch The layout sketch is a very useful tool for constructing complex assemblies or for laying out a mechanism in an assembly. Sketches in the assembly have the same characteristics as they do in the part environment. In Figure 12.3, the assembly layout sketch is indicated with a heavy, dashed line for emphasis.
FIGURE 12.3 An assembly layout sketch
394
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 395
Organizing Assemblies
When combined with in-context techniques, assembly layout sketches can help to determine the shape of parts. You can also use layout sketches to mate assembly components to far more robust and dependable mates, rather than mating part to part. The sketch shown in Figure 12.3 is used for both of these techniques. The shape of the frame and the major pivot points are established in the 2D sketch. The wheels are also mated to the sketch. When you use an assembly layout sketch for either the in-context part building or simply part positioning, the main advantage that it offers is having a single driving sketch that enables you to change the size, shape, and position of the parts. You can use as many layout sketches as you want, and you can make them on different sketch planes. This enables you to control parts in all directions.
Assembly reference geometry Planes and axes are frequently created within assemblies to drive symmetry or placement of parts. You can use assembly layout sketches to create the reference geometry entities. When you create reference geometry within the assembly in this way, be aware that the normal history-based parent/child relationships are still followed. The familiar icons for reference geometry entities are also used in the assembly tree.
History-based and non-history-based portions of the assembly tree Because features such as sketches and reference geometry are history-based and found in the assembly tree, at least a portion of the assembly FeatureManager is history-based. However, not all of it is. For example, the list of parts and subassemblies is not history-based. Sketches and reference geometry may appear before or after the list of parts, subassemblies, and mates. All of the remaining entity types that can be found in the assembly FeatureManager are also history-based features, and you can reorder them in the tree. However, several situations can disrupt the process. Under normal circumstances, sketches and reference geometry at the top of the assembly FeatureManager are solved, then the parts are rebuilt if required, and then the mates are solved. This ensures that the sketches and reference geometry are in the correct locations so that if parts are mated to them, then all of the components end up being the correct size and in the right position. Assembly-level reference geometry can be created that references component geometry instead of layout sketches. This creates a dependency that changes the usual order. For example, the planes are usually solved before the part locations, but when the plane is dependent on the part location, the plane has to be solved after the part. If a part is then mated to the plane, you are beginning to create a dependency loop, such that the plane is solved, followed by the part, then the plane again because the part has moved, and then the mate that goes to the plane has to resolve the part. If you are a bit confused by all of this, don’t worry. You can simply follow this rule: Do not mate to anything that comes after the mates in the assembly FeatureManager tree. This includes assembly planes or sketches that are dependent on part geometry, assembly features such as cuts, in-context features, component pattern instances, Series Holes, or SmartFasteners.
BEST PRACTICE
This is probably a lot of information for a new user, but if you remember this rule, then you can avoid creating models with circular references, where A is dependent on B, which is dependent on A — a never-ending loop that causes major problems for large assembly rebuild times.
395
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 396
Working with Assemblies
Parts and subassemblies Parts and subassemblies are shown with their familiar icons in the design tree. You can reorder and group them in folders, which is covered in the next section.
Folders You can create folders to organize and group both parts and mates. I discuss this technique in detail later in this chapter.
Mates The Mates area remains a constant, single folder, but you can organize it by reordering the mates and grouping them into folders.
Assembly features In manufacturing, once parts are assembled, secondary machining operations are sometimes applied to them to ensure that holes line up properly, or for other purposes. For example, assembly features can be cut extrudes, cut revolves, or hole features. These features appear only in the assembly, not in the individual parts. You should not confuse assembly features with in-context features. In-context features are created in the assembly with a reference between parts, but the sketch and feature definition are in the part itself.
Component patterns Component patterns can pattern either parts or assemblies by creating either a pattern defined in the assembly, or a pattern that follows a pattern feature created in a part. The pattern is listed as a feature in the assembly FeatureManager, and all of the instance parts appear indented from the pattern feature in the design tree. You can hide or suppress each instance, change its configuration, and in most ways control it as if it were a regular part in the design tree. Because the options for locally defined patterns are comparatively limited, users generally like to use part feature patterns to drive the component patterns when possible. To improve performance, it is best to pattern subassemblies if possible. If it is not possible, then patterning a group of parts is the next best option. Making multiple patterns, one for each part, is an inefficient way to accomplish the same thing.
PERFORMANCE
396
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 397
Organizing Assemblies
In-context reference update holders It is difficult to get a good picture of assemblies in general without including a discussion about incontext references, but to treat the subject properly, it also requires its own section. When you create a reference between parts in an assembly, the assembly needs to remember which parts are involved in the reference. The parts also need to remember which assembly was used to create the relation because the parts are positioned in the assembly, and the reference has meaning only with regard to a particular relative position between the parts. When you create the relation, a placeholder has to be left behind in the assembly to hold this information. This placeholder is called an Update Holder. The Update Holders do not display by default. To see them, you must RMB click the top level in the FeatureManager and select Show Update Holders. They only exist when in-context references exist in the assembly, and there is one Update Holder for each in-context reference. You cannot do very much with the Update Holders, other than query them for parent/child relations and to list the external relations, but they serve as a reminder that you have in-context references to maintain. Several years ago, they were displayed by default, but they were later hidden by default, presumably because users were confused by the presence of something that you could not do anything with. In-context modeling methods are often scorned by some users, and if you have a list of 50 or 60 Update Holders, then you may be perceived as an overzealous novice. For more information on this feature, see Chapter 16.
Smart Fasteners Smart Fasteners are assembly features that automatically select Toolbox parts for use in standardsized holes, and you can use them in many different ways. The Smart Fastener feature in the assembly FeatureManager is used to edit the definition of the Smart Fastener, which can include adding items such as nuts and washers. You can also use Smart Fasteners in conjunction with the Hole Wizard to place appropriate holes and matched fasteners, all in a single step.
CROSS-REF
Smart Fasteners, Toolbox, and the Hole Wizard are discussed in detail in Chapter 17.
Hole Series The Hole Series is a Hole Wizard–type feature that you apply in an assembly. This wizard leaves the feature icon in the assembly, but also adds features directly to the individual parts. It also adds in-context Update Holders to the assembly FeatureManager, as shown in Figure 12.4. The Series Hole is designed to go through a series of parts, placing the appropriate hole type in each part, counterbore, through, threaded, and so on.
397
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 398
Working with Assemblies
FIGURE 12.4 Adding in-context Update Holders
Using Subassemblies The first tool for organizing assemblies is the subassembly. A subassembly is just a regular assembly that is used as a component in another assembly. The number of levels of subassemblies is not limited to a specific number, although for different sizes and types of assemblies, I encourage you to establish a best practice for your company. For example, establish a guideline that suggests that subassemblies of 100 parts or less go no deeper than three levels.
BEST PRACTICE
You can use several criteria to determine how subassemblies are assigned: n Performance n Bill of Material
398
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 399
Organizing Assemblies
n Relative motion n Pre-fabricated, off-the-shelf considerations n According to assembly steps for a process drawing n To simplify patterning The underlying question here is based on the multiple functions of your SolidWorks assembly model. Is it primarily a design tool? A visualization tool? A documentation tool? A process tool? As a design tool, the assembly is used to determine fits, tolerances, mechanisms, complex shapes that span parts, and many other things. As a visualization tool, it simply has to look good and possibly move properly if that is part of the design. As a documentation tool, it is important how the model relates to the Bill of Materials, and the order in which subassemblies are added. As a process tool, you need to be able to show the assembly in various intermediate states of being assembled. I have seen companies create multiple assembly models for different purposes. Sometimes the requirements between the different methods are contradictory and cannot all be met at the same time with a single set of data. Again, depending on what information you need to be able to extract from your SolidWorks models, you may want to approach assembly modeling and organization differently.
Creating subassemblies from existing parts You can create subassemblies from parts that already exist in an assembly. To do this, select the parts that you want to add to the subassembly, and then select Form New Subassembly Here from the RMB menu. You are then prompted to assign a name to the new subassembly. When creating a new subassembly from existing parts or when moving parts into or out of a subassembly from the upper-level assembly, some things may be lost. For example, mates are moved from the upper level to the subassembly. If you have in-context relationships, they may be removed. Operations that create subassemblies cannot be undone easily.
CAUTION
Once you have created the subassembly, you can add or remove components using the drag-anddrop method. For example, Figure 12.5 shows the cursor that indicates that the part named Left Crank is being moved into the subassembly named bike crank. To move a part out of a subassembly, simply drag the part into the upper-level assembly.
FIGURE 12.5 Moving parts into a subassembly
399
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 400
Working with Assemblies
When you are dragging a part out of an assembly and into another one, you may again see the cursor symbol that appears in Figure 12.5. If you do not want this to happen, then hold down the Alt key while dragging. The cursor symbol changes to the Reorder cursor (a reversed, L-shaped arrow), and the part is placed after the subassembly rather than within it.
NOTE
Insert a new subassembly Along with the RMB menu option Form New Subassembly Here, which takes existing parts and puts them into a newly created subassembly, you can use another option called Insert New Subassembly. The names of these functions do not adequately describe the difference in what they do. Insert New Subassembly inserts a blank subassembly at the point in the design tree that you indicate by right-clicking it. You can place components into the subassembly by dragging and dropping them from the main assembly, or you can open the assembly in its own window, and insert parts by using the usual methods.
Dissolving subassemblies If you would like to get rid of a subassembly but want to keep its parts, then you can use the Dissolve Subassembly option through the RMB menu. This option has some of the same consequences of the Form New Subassembly Here option in that mates are moved from the subassembly to the upper-level assembly, and you may lose in-context relations and assembly features.
Organizing for performance Performance in SolidWorks is a euphemism for speed. Subassemblies can contribute to speedsaving modeling techniques by segmenting the work that the software needs to do at any one time.
Solving mates The mates that contribute to putting the pieces of an assembly together are solved at the level of the top assembly. Under normal circumstances, subassemblies are treated as static selections of parts that are welded together, and their mates are not solved at the same time that the top-level assemblies’ mates are solved. This segmenting of the mates leads to improved performance by only solving one set of mates at a time. Mates are usually solved as a single group unless there is a special situation, such as mates to incontext features, component pattern instances, or an assembly feature, all of which have already been described in this chapter. When one of these situations occurs, the mates have to be divided into separate groups or solved multiple times. This is done transparently behind the scenes so that the user does not have to worry about it.
Flexible subassemblies When you create subassemblies, the mates for these parts are not solved in the upper-level assembly. This means that if a subassembly is a mechanism, the mechanism does not allow Dynamic Assembly Motion in the upper-level assembly. For example, in Figure 12.6, the front fork is a linkage mechanism, but it is also a subassembly. Without reassembling the parts of the fork in the upper-level assembly, you can allow the mates from the fork subassembly to be solved in the
400
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 401
Organizing Assemblies
upper-level assembly by using an option in the Component Properties dialog box, which is also shown in Figure 12.6. When you select the Flexible option in the Solve as section, you enable the mates of this subassembly to be solved in the upper-level assembly.
FIGURE 12.6 Creating a flexible subassembly
Solve as flexible or rigid
To access the Component Properties dialog box, RMB click the subassembly and select Component Properties from the menu.
Legacy data If you have assemblies that were built in older versions of SolidWorks (such as SolidWorks 2001+), mates used to be split up into multiple mate groups, which represented the groupings that mates were solved in, which was forced by mating to the history-based features in the assembly FeatureManager. SolidWorks no longer displays mate groups, but the groups are still used in the background to solve mates.
Organizing for the BOM The Bill of Materials, or BOM, is a table that is placed into a drawing of an assembly. This table shows the parts used in the assembly and includes other information, such as part numbers, descriptions, and custom property data.
CROSS-REF
SolidWorks BOM functionality is discussed in depth in Chapter 24.
401
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 402
Working with Assemblies
Businesses often represent assemblies and subassemblies in various ways by using MRP or ERP software (Manufacturing Resource Planning or Engineering Resource Planning). The methods that accountants and manufacturers use to organize assemblies are not always the same as those that an engineer or designer might choose, but some companies require the BOM on the drawing to match the MRP or ERP Bill of Materials. When forced into modeling something in an unnatural way to satisfy an outside requirement such as special BOM requirements, it might be best to detach the unnatural part and model normally. In the situation mentioned here — where MRP is forcing how the assembly is put together by requiring the BOM to match MRP — I recommend separating the BOM from the assembly structure. This ensures that the BOM becomes a manually maintained document, rather than building an assembly that makes other SolidWorks functions difficult. Alternatives to this approach would be to make configurations or entirely new assembly documents to drive the BOM.
BEST PRACTICE
Grouping subassemblies by relative motion A more natural way to group subassemblies is by considering relative motion. In the bicycle example, each wheel is a separate subassembly because it moves as a unit relative to the rest of the assembly. Figure 12.7 illustrates where relative motion might be on the bicycle.
FIGURE 12.7 Grouping subassemblies by relative motion
Rear wheel
Drive train
Rear suspension swingarm
402
Front wheel
Front suspension linkage
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 403
Organizing Assemblies
Grouping subassemblies by relative motion is great for assembly modeling, but it does not usually reflect product reality very well. Using this method, you often end up with parts in the subassembly that would have to be disassembled in order to actually put the physical parts together. However, if your only consideration is ease of modeling, then this is probably the method to use.
Organizing groups of purchased components If you are modeling a product that is created from a shopping list of purchased components, then it may make the most sense to organize your subassemblies into groups of parts that are purchased together. In fact, purchased subassemblies are often modeled as single parts, except when relative motion is required in the purchased assembly. For example, in the bicycle assembly, the sprockets on the rear wheel are purchased as a separate unit, and yet the part that mounts onto the wheel moves relative to the sprockets that are driven by the chain. This is an example of a purchased part that would be modeled as a subassembly to show relative motion. The bicycle chain, another purchased subassembly, has not yet been added to this assembly, and is a more complex model. The desire to show all of the individual links moving through the path may override both the complexity of assembling it and the performance considerations of exercising all of the mates. Although the BOM method of organizing assemblies sometimes leads to unnatural solutions, you should not discard it altogether. If you can devise concessions in order to make the BOM work automatically, then you should do this.
Depicting an assembly process Manufacturing and assembly processes need to be documented as well as individual part design. You often need to create exploded-view assembly instructions for manufacturing or service documentation at each step of a multi-step assembly process. Figure 12.8 shows a page of this type of process documentation. This is certainly a task that is different from the initial design or modeling of the assembly, and it may require an entirely separate model. Generally, you can perform the different steps by using a separate configuration for each process step, with exploded views for each configuration.
Item numbering Balloons number the parts according to the item number that is used in the BOM, but of course you do not know the item numbers until the BOM is created. You can influence the item numbers by reordering the parts in the assembly (which is discussed later in this chapter), by manually editing item numbers, or by manually numbering the balloons. All of this is discussed in detail in Chapter 24.
Individual steps Each step corresponds to an assembly configuration (discussed in Chapter 14), and you can place them on a separate sheet of the drawing (discussed in Chapter 21). Each configuration can have multiple exploded views, if necessary, to show all of the steps.
403
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 404
Working with Assemblies
FIGURE 12.8 Assembly process documentation
Patterning considerations The most efficient way to pattern large numbers of components in an assembly is to pattern a single subassembly with all of the components to be patterned in it. While this may not be easily combined with some of the other considerations that were mentioned previously, it is another option that you can use to organize assemblies.
Using Folders Folders are primarily used in the assembly FeatureManager for grouping parts and mates into either special classifications for easy browsing, or groups that can be easily hidden and shown, or suppressed and unsuppressed, as appropriate. Figure 12.9 shows some examples of these folders.
Creating folders in the FeatureManager You can add folders to the assembly FeatureManager in one of two ways: n Add to a new folder n Create a new folder
404
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 405
Organizing Assemblies
FIGURE 12.9 Folders that are used to organize components and mates
Add To New Folder To use the Add To New Folder tool, RMB click a component or mate (or selection of components or mates) and select Add To New Folder from the menu. This moves the component or mate into the folder. Folders do not affect the assembly in any functional way; they are simply for organization, to speed browsing and selection.
Create New Folder To simply create a new folder without putting anything into it right away, RMB click either the Mates area or the components list, and select Create New Folder from the menu.
Adding items to existing folders To move an item into an existing folder, just drag the item (component or mate) onto the folder. If the folder is expanded, showing its contents, then you can also drag the item as if you were reordering a feature in the FeatureManager of a part, and drop it in the list of items where you would like it. If you are dragging a part or assembly and trying to put it immediately after an assembly, then a cursor may appear, like the one shown in the center in Figure 12.10. This cursor means that the part is going to become part of the assembly. If this is not what you are trying to do, then hold down the Alt key while dragging; the part is placed into the folder immediately after the assembly, instead of being made a part of the assembly. The third image in Figure 12.10 shows the cursor with the Alt key pressed.
405
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 406
Working with Assemblies
FIGURE 12.10 Moving items into folders
Reordering items in the tree There are times when you may want to reorder items in the assembly tree. For example, you may want to place items close to one another in the tree, or you may be preparing to put items that are next to one another into a single folder. You can reorder mates simply by dragging them. Mates display in the order in which they are created, but the order is not significant. They can be reordered however you like. Components also display in the order in which they are added to the assembly, and you can reorder them in any way you like. It is often useful to have an ordering strategy that helps you to work with the model. I usually try to keep the biggest parts, or the parts that everything else is mated to, or the part that is treated as “ground,” as the first part in the assembly. The fasteners and other cosmetic or BOM-driving parts are put at the end of the tree, usually in a descriptive folder.
BEST PRACTICE
Working with Tree Display Options Display options for items in the FeatureManager are often overlooked, but can be useful for displaying data about parts, subassemblies, mates, and features. Figure 12.11 shows the RMB menu options.
NOTE assemblies.
406
All of these options are available for parts and drawings as well, except for the View Features option and the View Mates and Dependencies option, which are related to
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 407
Organizing Assemblies
FIGURE 12.11 Tree display options in assemblies
Show feature names and descriptions If you are so thorough that you have added descriptions to your features, then you are doing well. This option refers to the descriptions of features in the parts. The middle image in Figure 12.11 shows a section of the FeatureManager for the bicycle frame part; some of the features have had descriptions added with both of the options for feature names and feature descriptions turned on. The image to the right in Figure 12.11 shows the result of turning off the feature name, with only the feature description option turned on. If no feature description has been created, then the feature name displays. Feature descriptions always appear in double quotes.
Show component and config names and descriptions The image to the left in Figure 12.12 shows the default arrangement of displaying component and configuration names in the assembly FeatureManager. This example uses the rear wheel assembly from the bicycle assembly. In assemblies, you cannot turn off the component names and the component descriptions. SolidWorks issues a statement when you try to turn off both the name and the description, saying, “You cannot hide both the component name and the file name. At least one must be visible in the tree.”
Using names other than the part filename in the assembly FeatureManager The message in the previous paragraph distinguishes between the filename and the component name that is listed for individual parts or subassemblies in the assembly FeatureManager. You can specify the component name in the Component Properties dialog box by RMB clicking the component in the assembly FeatureManager and selecting Component Properties.
407
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 408
Working with Assemblies
FIGURE 12.12 Component name options
However, you can assign a component name for a component that is different from the filename only if a special setting is turned off (the setting defaults to on). You can access this setting through Tools ➪ Options ➪ External References ➪ Update Component Names When Documents Are Replaced. What the name of the setting has to do with showing a component name in the FeatureManager is not exactly clear, but these are the steps that you have to go through if you want to change how the part and subassembly names display in the assembly FeatureManager. After going through the preceding steps, you still receive the warning message about the filename and the component name. This is apparently an “unintended feature,” or bug, and should likely say that you cannot turn off both the component name and the component description at the same time. There may be a situation where you want to show a name other than the filename in the FeatureManager. For example, your company may be using sequential part numbers for the filenames, which are difficult to read, and you want something descriptive in the design tree so that you do not need a cross-reference sheet next to your computer that equates filenames to meaningful descriptions. If you prefer, you can avoid a lot of problems by just using the part description instead of the filename or the component name. The choice is up to you. Because the component name options are convoluted, obscure, and will need to be set on each computer where you would like to use them, I do not recommend them. It is simpler and more reliable to use either the default component name (which is the same as the filename) or the component description.
BEST PRACTICE
One of the problems with using the component description is shown in Figure 12.13, where the user did not enter proper descriptions for the parts, and SolidWorks used the default description in the templates. The tire and spokes use configurations, which display in the figure.
408
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 409
Organizing Assemblies
FIGURE 12.13 An example of what can occur when you do not enter proper descriptions for parts
Viewing features, mates, and dependencies The last set of options, shown in Figure 12.11, defines what displays under the name of each component. The default setting is for the part’s features or the subassembly’s components to display, just as if the part or subassembly were open in its own window. The View Mates and Dependencies option can also show the features, but they are placed into a separate folder. This option makes it very easy to see the mates that are assigned to an individual component. For example, in Figure 12.14, the image to the right shows the mates directly under the BibleBikeFrame part. This often makes troubleshooting much easier because it isolates the mates for a single part. Notice also that the first folder under the part name in the image to the left in Figure 12.14 is the Mates folder. This indicates that, regardless of whether you choose to display mates or features, you always have easy access to the other type. Another technique for displaying mates is to split the FeatureManager and to show the PropertyManager in one pane. As a result, any parts that are selected show their mates in the PropertyManager pane. If two selected parts have mates in common, then the common mates appear in bold type, as shown in Figure 12.15. This is an extremely useful method for looking at mates. This function does not appear to work in SolidWorks 2007 sp1.0, although it does work properly in sp0.0. Service Pack 1.0 was the latest available service pack at the time that this chapter was written. SolidWorks knows about the bug and has labeled it a “regression,” which means that it will receive priority in subsequent fixes. The fix may be available in sp2.0.
CAUTION
409
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 410
Working with Assemblies
FIGURE 12.14 You can view features, as well as mates and dependencies.
FIGURE 12.15 Showing mates in the PropertyManager pane
410
19_080139 ch12.qxp
3/26/07
3:53 PM
Page 411
Organizing Assemblies
Tutorial: Managing the FeatureManager This tutorial uses the BibleBikeAssembly.sldasm file found on the CD-ROM for Chapter 12. Follow these steps to learn about managing the FeatureManager: 1. Create a new subassembly within the existing assembly using the parts BibleBikeFrame and ChainstayBibleBike. Name this new assembly FrameAssembly.SLDASM. 2. Reorder the new FrameAssembly to the top of the design tree. 3. Reorder the other parts and assemblies so that the bigger assemblies appear higher on the list, and the parts appear at the bottom. (Remember that the Alt-drag option to prevent a component from being placed into a subassembly.) 4. Drag the part called BB (for Bottom Bracket) into the FrameAssembly (drag without using the Alt key). The assembly FeatureManager at this point is shown in Figure 12.16.
FIGURE 12.16 The starting state, and the state as of step 4
5. Select both wheels and then click Add To New Folder from the RMB menu. Name the new folder Wheels, and move it to the bottom of the tree. 6. Expand the Mates folder, select the first four mates, and put them in a new folder (select Add To New Folder from the RMB menu). Name the new folder Centering Mates.
Summary Assemblies are more than simply parts and subassemblies put together with mate relationships; several other types of features and placeholders can also exist in the assembly FeatureManager. Organizing assembly components is fairly straightforward, and can offer benefits for finding parts as well as controlling suppression and display states globally.
411
12
19_080139 ch12.qxp
Part III
3/26/07
3:53 PM
Page 412
Working with Assemblies
The assembly FeatureManager contains several options for the data to display for subassemblies, parts, configurations, and features within. Remember that all of this data that you include in your SolidWorks documents can be accessed and reused later on, and so it is worth the effort. Descriptions can be very important, both at the part level, and also for features and configs.
412
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 413
Getting More from Mates
I
n SolidWorks assemblies, mates are the basic units that either make everything work together and function properly, or fill the tree with errors and warning symbols. When properly handled, mates enable your assembly to react predictably to changes in parts in exactly the same way that sketch relations drive changes in part features. As a result, mates and sketch relations often have the same function and even the same weaknesses to watch out for. This chapter goes one step further with mates, by not just simply putting parts together with Coincident and Concentric mates, but also mating when tolerances, gaps, and symmetry become issues. You will also learn about the more advanced mate types that may be useful for special situations. One of the assumptions that I make in this chapter is that assembly mates are not just used for positioning parts, but also for motion. Making motion work takes a little more than just establishing the right spatial relationship between parts; it usually also involves analyzing the open degrees of freedom. From time to time, I have met users who take the “AutoCAD” approach to putting parts together into assemblies, by simply placing parts at the correct X- and Y- coordinates without assigning any relationships to the parts around them. This defeats most of the purpose of creating parametric, associative assemblies in the first place. Assembly mates are an extremely powerful tool for enabling your assemblies to react predictably to change.
413
IN THIS CHAPTER Applying mates Mating for motion Advanced mate types Editing and troubleshooting Mate options Summary of mate best practices Tutorial: Mating for success
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 414
Working with Assemblies
Applying Mates An average assembly of 100 parts would likely have almost 300 individual mates. If you create these parts one at a time, taking perhaps a minute for each mate, then you would spend five hours just applying mates. Any time that you can save applying mates is a benefit to you — assuming you still get the correct results — because it is time that you can spend doing something else. In this section, you will learn efficient mating strategies, as well as speedy techniques.
Mating through the Mate PropertyManager The Mate PropertyManager is the default method for applying mates, and was used briefly in Chapter 5. The Mate PropertyManager interface is shown in Figure 13.1. You can create mates by pre-selecting entities before applying the Mate command or selecting them after you open the Mate PropertyManager.
FIGURE 13.1 The Mate PropertyManager interface
414
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 415
Getting More from Mates
Mate workflow If you make a lot of mates, it is important to have an efficient rhythm when working with the interface. The most efficient way to use the Mate interface is as follows: 1. Click the first entity. 2. Click the second entity. 3. Click OK on the RMB cursor icon, which is shown in Figure 13.2.
FIGURE 13.2 The OK option on the RMB cursor
Or, if the automatic default mate type is not the mate that you want to apply, then select it from the popup list, which is shown in Figure 13.3.
FIGURE 13.3 The Mate selection popup list
4. Click the green check mark icon from the popup list. 5. Repeat steps 1 to 4. 6. After the last mate, press Esc, the green check mark icon, or the red X icon from either the PropertyManager or the confirmation corner in the upper-right corner of the graphics area. In SolidWorks 2007 sp0, there is a bug with the distance mate that has been fixed in sp1.0. In sp1.0, the distance mate defaults to the actual distance between the entities, but in sp0, it defaults to 1.000 inch, and so you must manually type in a distance.
CAUTION
View and model positioning Sometimes you will have to rotate the model to achieve the correct view in order to select faces or edges. There are also times when you will want to pre-position so that the model snaps into the correct position automatically. You can rotate individual parts in an assembly by dragging with the RMB. You rotate the view by dragging with the middle-mouse button, or MMB. You can move parts by dragging them with the left-mouse button, or LMB. You can pan the view by pressing Ctrl and dragging with the MMB. When you drag a part with the LMB while the Mate PropertyManager is active, SolidWorks does not add the selected entity to the Mate Selections list.
415
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 416
Working with Assemblies
To summarize these actions: n To rotate an individual component in an assembly, drag with the RMB. n To move an individual component in an assembly, drag with the LMB. n To rotate an assembly view, drag with the MMB. n To pan an assembly view, Ctrl-drag with the MMB. If you have a Spaceball or 3D motion controller, you can perform all of these actions more easily and simultaneously using one hand for view rotations and the other hand for selections. You can also use a Spaceball to move parts.
TIP
Select Other The Select Other command enables you to select items that are hidden by other items. It is often used to select faces that are hidden behind other faces without rotating the part. You can apply the Select Other command through the RMB menu. Right-click where the face would be if you could see it. A list of entities displays, and you can select the entity you want from this list or from the graphics window. Moving your mouse over an entity in the list highlights the entity in the graphics window. Pressing Tab or scrolling the mouse wheel cycles through the entities one by one. Clicking faces with the RMB hides them, which allows you to see further down into the part or assembly. Clicking with the LMB either in the graphics window or the selection list box selects the item. Figure 13.4 shows the Select Other cursor and dialog box.
FIGURE 13.4 The Select Other cursor and dialog box
The item about to be selected turns red in the graphics window. Although this selection method is also used for other purposes, it is often used for selecting faces for mating.
416
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 417
Getting More from Mates
Multiple Mate mode Multiple Mate mode enables you to select one face in order to mate multiple faces from other parts to it. Figure 13.5 shows the interface for this mode, which you can toggle to from the Mate PropertyManager interface. It also shows several small blocks being mated to a single large block. This function works only with the Standard Mate types, not with any of the Advanced Mates, which are discussed later in this chapter.
FIGURE 13.5 The Multiple Mate Mode interface
You can create a special folder for all of the multiple mates by selecting the Create Multi-mate Folder check box in the Mate Selections PropertyManager. You can also automatically link the values for distance and angle mates with link values by selecting the Link Dimensions check box.
SmartMates SmartMates are mates that you can create automatically by dragging one part onto the other without invoking the Mate command. There are three different methods that you can use to apply SmartMates: n Alt-dragging the part n Dragging the part from one window to another n Using Mate References
Alt-dragging a SmartMate Probably the easiest way to quickly create a SmartMate is by Alt-dragging. One, two, or even three mates can be applied at once by holding down the Alt key while dragging a face or edge from one part onto a face or edge on another part. When you are dragging a part while pressing the Alt key, the part is made transparent to allow you to see other part faces that you may want to mate it to. A special cursor appears when a SmartMate is about to be applied. Figure 13.6 shows the cursors that appear for adding Concentric and Coincident mates.
417
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 418
Working with Assemblies
FIGURE 13.6 Applying a SmartMate
When you drop the face onto the mating face to complete the mate, you must use the popup Mate toolbar to accept or alter the mate. In the examples in Figure 13.6, a face is being dragged onto another face. However, you can also drag edges and vertices. Mates are limited to being either Coincident or Concentric. The peg-in-hole mate is actually both a Concentric mate and a Coincident mate. This is the type of mate that is created between a screw and a hole, and is the result of Alt-dragging a circular edge onto a circular edge. When the circular edges are created by the intersection of a cylindrical face and a flat face, the Concentric mate goes between the two cylindrical faces, and the Coincident mate goes between the flat faces. The peg-in-hole mate is illustrated in Figure 13.7. The image to the left shows the state of the parts before the SmartMate. The image in the middle shows the SmartMate orienting the part in the wrong way so that the two parts interfere. In the image on the right, the part to which the SmartMate is applied has been reoriented by pressing Tab before the SmartMate is accepted by dropping the part. You can use the Tab key to flip the alignment if a SmartMate tries to put parts together in the wrong way. If you are in the process of Alt-dragging, make sure to release the Alt key before pressing Tab. The Alt-Tab combination shows a list of open applications.
TIP
418
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 419
Getting More from Mates
FIGURE 13.7 Using SmartMate to create the peg-in-hole mate combination
Alt-drag this edge
Drag between windows You can apply SmartMates when dragging a part from one document window to another, or when copying a part within a single window by Ctrl-dragging. The best way to drag a part from one window into another is to tile the windows using the Tile command in the Window menu. Then drag the part using the face or edge that you would like to mate, and bring it near to the face in the assembly to which you want to mate it. The transparent preview should snap into place. Again, if it is backwards, you can just press Tab. The same is true when copying a part in the graphics window of an assembly. You can simply Ctrldrag a face of the part to the face of the new location.
419
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 420
Working with Assemblies
Mate references Mate references are model faces, edges, or vertices that are pre-selected and used in a SmartMatelike fashion when dragging a part in from Windows Explorer or from a library window. Mate References are discussed in Chapter 19 in the course of discussing library parts.
Mating with macros If all of the confirmations and extra mouse-clicks to open and close windows are not for you, and you are just applying simple mates, then you may want to use macros to mate parts. Macros are not going to give you the same flexibility, but they do improve speed. However, you have to have the parts ready to go when you press the macro button, or you will create the wrong mate. You can find macros for Coincident, Concentric, Parallel, Perpendicular, and Tangent mates on the CD-ROM. For example, to use the concentric macro, you would need to pre-position the parts so that they are within 90 degrees of the proper alignment, have one of the parts mated in place such that that only one part will move, select the two cylindrical faces, and then run the macro.
CROSS-REF
Macros are discussed in depth in Chapter 32.
To run the macro, pre-position the parts, pre-select the faces, click Tools ➪ Macro ➪ Run, and then browse to the macro. Chapter 32 shows you how to connect macros to hotkeys, which makes this process easier. Like SmartMates, macros work best for the simpler mate types where you do not need to select any options.
Mating for Motion Dynamic Assembly Motion is a powerful tool for visualizing the motion of mechanisms in SolidWorks. It works best if there is a single open degree of freedom.
Degree-Of-Freedom analysis When working with motion in SolidWorks, you need to be comfortable with degrees of freedom. When inserted into an assembly, each model has six degrees of freedom: n Translation in X (tX) n Translation in Y (tY) n Translation in Z (tZ) n Rotation about X (rX) n Rotation about Y (rY) n Rotation about Z (rZ)
420
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 421
Getting More from Mates
When applying mates, and especially when troubleshooting motion or overdefinition problems, it is important to look at how each mate translates into degrees of freedom being tied down. For example, a Coincident mate, planar face to planar face, ties down one translation degree of freedom (in the direction perpendicular to the faces), and two rotational degrees of freedom (about directions which lie in the plane of the faces). What remains are two translational degrees of freedom in the plane of the faces and one rotational degree of freedom about an axis perpendicular to the planar faces. A point-to-point Coincident mate ties down three translational degrees of freedom, and the part can only rotate. An edge-to-edge Coincident mate ties down two translational and two rotational degrees of freedom. As a result, a part that you mate in this way can only slide along the mated edge and rotate around the mated edge. When using face-to-face Coincident mates, it takes three mates to fully define a block type part. When using edge-to-edge Coincident mates, it only takes two mates. You should read through the section on Summary of Mate Best Practices before adopting this approach.
TIP
Something to be careful about is that a degree-of-freedom analysis frequently predicts an overdefined mate scenario when SolidWorks does not in fact display any errors or warnings. For example, if one block is mated to another with the simple case of three face-to-face Coincident mates, and each Coincident mate ties down one translational and two rotational degrees of freedom, then the part would be over-constrained by three rotational degrees of freedom. This may be an overly cautious approach, but it can mean the difference between an assembly that works and one where errors are frustratingly persistent. If you are careful to approach all parts with the degree-of-freedom analysis in mind such that any newly added mate does not duplicate any of the degrees of freedom that are already tied down, then you will have fewer assembly mate errors and fewer problems with assembly motion.
BEST PRACTICE
This means that instead of the traditional three face-to-face Coincident mates, you would have one face-to-face Coincident (one translational degree of freedom, two rotational degrees of freedom), one edge-to-face Coincident (one translational degree of freedom, one rotational degree of freedom) and one point-to-face Coincident (one translational degree of freedom). This accounts for three translational and three rotational degrees of freedom without overdefining any of them. It is true that SolidWorks internally compensates for over-defined degrees of freedom, but relying on it to do so and then tempting fate by methodically over-defining all assemblies is a risk that you do not have to take, even though it is common practice.
Best bet for motion The best bet for creating motion in a SolidWorks assembly is to leave open a single degree of freedom. This means that there is only one way the part can move, back and forth, either translation or rotation. Computers in general do not respond well to ambiguity. Dragging an item that may move in several ways is more likely to cause jerky or hesitant motion.
421
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 422
Working with Assemblies
A good example of this kind of problem with motion can be found in one of the sample assemblies that installed with SolidWorks 2007. I have included this example on the CD-ROM for your convenience, and it is shown in Figure 13.8. The filename for the assembly is Plunger.sldasm.
FIGURE 13.8 An assembly displaying best bet for motion
Drag here and the motion is smooth Drag here and the motion is poor
If you drag the assembly parts from the locations shown in Figure 13.8, the performance varies. This is because when you drag the handle parts, for every position of the handle, there is only one solution for the rest of the parts. However, when dragging the plunger bar, for every position of the plunger bar there are two possible positions for both the links and the handle. This kind of ambiguity causes problems in SolidWorks assemblies such as assemblies that have open degrees of freedom but will not move or move in a jerky fashion. Another example of difficulties related to open degrees of freedom and motion is shown in Figure 13.9. The grippers at the end of the arm move when the rest of the arm moves, but the grippers cannot be independently controlled. To fix this problem, you may want to either use the Fix/Float option (available through the RMB menu), or use configurations with mates suppressed or unsuppressed. You can open this assembly from the CD-ROM, in the filename called Chapter 13 Robot Assembly.sldasm.
422
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 423
Getting More from Mates
FIGURE 13.9 A robot arm assembly with degree-of-freedom conflicts
Working with Advanced Mate Types Advanced mate types greatly expand the number of ways that you can put parts together into assemblies. Advanced mate types include the following: n Symmetric n Cam n Width n Gear n Rack and Pinion n Limit n Belts and Chains
423
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 424
Working with Assemblies
Symmetric mate The Symmetric mate works a lot like the Symmetry relation in sketches, except that a plane is used as the plane of symmetry instead of a construction line. Figure 13.10 shows a Symmetric mate being applied to the gripper jaws. The Symmetric mate is listed in the Advanced Mates pane of the Mate PropertyManager.
FIGURE 13.10 Applying a Symmetric mate
Cam mate The Cam mate creates a special instance of either the Coincident or Tangent mate. Four conditions exist with the Cam mate: n Coincident: Vertex on the follower mated to a cam that is created from a single closedloop face (spline, circle, ellipse). n Tangent: Cylindrical or planar face mated to a cam that is created from a single closedloop face. n CamMateCoincident: Vertex on the follower mated to a cam that is created from multiple faces. This condition enables the follower to go all the way around the cam, not stopping at the broken faces or following the extension of a single face. n CamMateTangent: Cylindrical or planar face mated to a cam that is created from multiple faces. This condition enables the follower to go all the way around the cam, not stopping at the broken faces or following the extension of a single face. Figure 13.11 shows both single-face and multi-face cams, along with the Cam Mate interface. The two assemblies are available from the CD-ROM in the file named Chapter 13 Cam.sldasm. If you open the assemblies and spin the cam plate, you will notice that in both cases, the flat follower does not work very well. In fact, in the single face cam assembly, it does not work at all.
NOTE 424
Barrel (cylindrical) cams cannot use the Cam mate to create cam motion.
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 425
Getting More from Mates
FIGURE 13.11 Using Cam mates
Width mate The Width mate is often used as a replacement for the Symmetric mate in situations where parts are modeled with some tolerance, and have a gap rather than touching face to face. The Width mate requires two pairs of faces to be selected, and works particularly well when a part has to be spaced evenly between two faces and there is no mid-plane, for instance when a square key is placed in a square keyway which is somewhat larger than the key. If a mid-plane is available, the Symmetric mate may be a better option, or at least a faster one to mate since the Symmetric mate only requires two faces and a plane. Figure 13.12 shows a good application for a Width mate as well as the PropertyManager interface for the mate.
FIGURE 13.12 Applying a Width mate
425
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 426
Working with Assemblies
Gear mate The Gear mate enables you to establish gear type relations between parts without making the parts physically mesh. You can also apply gear ratios and directions without physical connections, so that you can have a shaft in and a shaft out of a black-box transmission. You can open the assembly shown in Figure 13.13 from the CD-ROM. It is named Chapter 13 Gear Mate.sldasm. To see the effect of the mate, open the assembly and rotate the parts. Then edit the mate and change the ratio and direction. The selection for the Gear mate is just two cylindrical faces.
FIGURE 13.13 Applying a Gear mate
Rack and Pinion mate The Rack and Pinion mate takes rotational motion of one part and turns it into translational motion for a second part. Again, the parts do not need to be physically connected and can be simple representations of the actual geometry that is needed to drive the motion in the real world. Figure 13.14 shows an assembly that uses the Rack and Pinion mate. You can find this assembly on the CD-ROM with the filename Chapter 13 RackPinionMate.sldasm.
Limit mates You can apply limits to distance and angle mates in order to allow the parts to move within a certain range of values. Figure 13.15 shows the PropertyManager interface for the Limit Angle mate. Limit mates accept zero and negative values that are not normally accepted for dimensions in SolidWorks. When used properly, Limit mates can be an extremely powerful tool for creating more realistic motion in assemblies.
426
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 427
Getting More from Mates
FIGURE 13.14 Applying a Rack and Pinion mate
FIGURE 13.15 The Limit Angle PropertyManager
427
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 428
Working with Assemblies
Belt/Chain The Belt/Chain assembly feature is not technically a standalone mate type, but it uses mates to accomplish its task. The Belt/Chain feature can be used in two ways, to create relationships between sketch blocks or to create relations between parts. This feature also creates a sketch and a solid part representing the belt or chain. Chapter 4 has a tutorial that discusses the Belt/Chain functionality as it relates to sketch blocks. The functionality using solid parts as pulleys and sprockets is very similar.
Editing and Troubleshooting You should become proficient with editing and troubleshooting assembly mates. If you are not comfortable with repairing and modifying mates, then you may find assemblies frustrating to work with; as a result, you may avoid making changes to your assemblies. However, once you master the techniques, you will be less afraid of errors, and more confident and willing to experiment with assembly changes.
Editing existing mates If you are editing just one mate, then you can simply RMB click it and select Edit Feature. Remember that you can find mates in places other than the Mates folder at the bottom of the assembly FeatureManager; most notably, you can find them in folders under the parts that they are mating together. You can make several types of changes to mates, including changing the selections involved, the mate types being used, and the mate alignment. These types of changes are all shown in Figure 13.16, which displays a mate being edited. The selected faces are highlighted in the graphics window. To edit multiple mates consecutively without exiting the Mate PropertyManager, it is best if you pre-select the mates. Pre-selected mates are shown in the Mates panel as shown in Figure 13.16. You can switch from editing one mate to another by simply selecting the new mate in the Mates panel. If you select only one mate before clicking Edit Feature, but realize later that you want to edit multiple mates, more mates can be selected through the Flyout FeatureManager. After the Mates pane has been opened, you can add mates to it by selecting the mates from the Flyout FeatureManager. This technique is somewhat problematic because after selecting a single mate from the flyout menu, it collapses and you have to expand it again. Here is another good place to promote the use of the Enhancement Request forms on the SolidWorks Web site. Editing mates is a function that you will perform frequently, and so it requires a smooth and easy-to-use interface. However, the FeatureManager and the PropertyManager create an awkward workflow when you need to select features from the FeatureManager. An example is when you edit the sketch plane for a sketch; as soon as you select this option, the FeatureManager disappears. This can be frustrating when you just want to select a plane from the FeatureManager that was right next to the sketch, but now you have to manually expand the flyout menu and scroll to find the plane again. I encourage you to suggest improvements to this system directly to SolidWorks through the Enhancement Request forms on the Support Web site.
NOTE
428
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 429
Getting More from Mates
FIGURE 13.16 Editing a mate
When mate entities are lost, the mate displays a yellow triangle containing an exclamation mark, the text changes to a brown color, and a break appears in the mate icon, as shown in Figure 13.17. You can repair this problem by selecting the Invalid reference in the Mate Selections window and then selecting the correct item from the graphics window.
FIGURE 13.17 Repairing mates with missing references
429
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 430
Working with Assemblies
Troubleshooting It is best to troubleshoot an assembly mate problem as soon as it appears, and not after it has time to become complicated by other issues. Failed mates also cause performance problems because SolidWorks keeps trying to solve the mates that are in conflict with one another. Assembly problems often appear to be far larger than they actually are. For example, the entire tree may light up with warnings and error symbols when one extra or mistaken mate is applied. You can use several approaches to troubleshoot situations like this. In fact, I sometimes purposefully over-define mates just to locate a left-over mate or a mate that is not supposed to be there. Two types of symbols may help you to distinguish the kinds of errors that are present in different mate features. The yellow triangle that contains an exclamation point is really not an error; it is actually more of a warning. It tells you that this mate is in conflict with other mates (this symbol is used for a variety of warnings), but that the mate is still satisfied. One of the other mates with which it conflicts is probably not valid, and so this type of warning is usually accompanied by an actual error symbol where the mate is not satisfied. The red circle containing the X is a failed mate. This is a mate that is in conflict and is invalid. If it is also a Coincident mate, then the two Coincident entities are not coincident.
Distinguishing between the Warnings and the Errors You can use the following troubleshooting techniques: n Last in first out: When a mate is added that causes warning and error signs to appear throughout the design tree, you can usually correct the problem by removing this last mate. n Single elimination: If you are sure that the last mate added is correct, then you may want to go backwards up the tree starting at the bottom, suppressing individual mates until you find one that causes the warning and error signs to disappear from the tree. n Single addition: It may be easier to take the opposite approach, by suppressing all but the mates that you are sure of, and then gradually unsuppressing mates until the conflict reappears. n Suppress a part: With all of the mates active, try suppressing an individual part to see if this makes a difference. If it does, then unsuppress the part and look at the mates for that part in the Mates folder under the part. n Mate Xpert: The Mate Xpert is an automated routine that creates subsets of groups of conflicting mates. Each subset of mates has one mate that is not satisfied because of the conflict. This may help you to find the cause of the conflict. Figure 13.18 shows the Mate Xpert interface. You can access the Mate Xpert from the RMB menu.
430
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 431
Getting More from Mates
FIGURE 13.18 The Mate Xpert interface
In the past several releases, SolidWorks has become increasingly “error-phobic.” There are more and more ways to create mate errors that are simply not reported to the user. For example, if geometry goes missing from a part, the mate icon displays with a break on it, but the mate folder is not flagged. This means that you do not know that you have a broken mate until you go looking for it.
CAUTION
Another example is that when a mated part is fixed (using the Fix option), the conflicting mates are automatically suppressed without notifying the user. In addition, when a part is suppressed, the mate is shown as suppressed, but it is also shown as broken. As a result, you are unsure whether the mate is completely invalid or the parent parts are only suppressed.
431
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 432
Working with Assemblies
Examining Mate Options The Options pane of the Mate PropertyManager is shown in Figure 13.19. Most of the options are self-explanatory, except for the Use For Positioning Only option. This option positions a part but does not apply a parametric mate. Some users make extensive use of this option for various applications where you need the part located precisely, but do not need or want a mate. Positioning parts for Animator animations where the part does not move according to a mate is one example of a use for this option.
FIGURE 13.19 The Options pane of the Mate PropertyManager
Summarizing Mate Best Practices Sometimes best practice recommendations can contradict one another, and for each best practice recommendation that you find, there are likely several specific situations where the recommendation is invalid. As a result, you should apply the following recommendations carefully. n Each assembly should have at least one part that is either fixed or fully mated to the standard planes of the assembly so that it cannot move relative to the assembly. n You should use fixed parts sparingly. One part that serves as a “ground” for the assembly should be fixed. Other than that, the parts of imported assemblies are sometimes fixed to keep them from being moved accidentally. n Do not mate to time-dependent features in the assembly tree, or to in-context features in parts. You may want to refer to Chapter 12 for a refresher on time-dependent features in the assembly tree. This can create circular references where the assembly must be rebuilt multiple times to fully resolve the positions of all parts and sketches. n When possible, it is best to mate all parts to the “ground” part. Creating daisy-chain mates (where A mates to B which mates to C, and so on) forces the mates to be solved in a particular order, which may take more time to solve than otherwise. If all of the mates relate to established assembly references, the mates may be more stable. Chapter 11 describes using a skeleton in a part to make sketch and feature relations to. The concepts are similar.
432
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 433
Getting More from Mates
n When possible, leave part positions fully defined, especially when other geometry is dependent upon the position of parts. Some examples include in-context features, assembly features, or assembly-level reference geometry, which are dependent on part geometry. n Constraining the rotational degree of freedom for components such as screws, washers, and nuts is usually considered excessive. At times, open degrees of freedom may cause problems with complex motion, such as a gripper on the end of a robotic arm. SolidWorks functions well when there is a single, well-defined path between two points, but when there are multiple options, the software may become confused. n Do not leave errors unresolved in the tree. n Remember to use subassemblies to break up the number of mates that are solved in the top-level assembly. n Limit the use of flexible subassemblies. n Do not mate to entities that may be removed later by suppressing or unsuppressing features, especially edges or faces that are created by features such as fillets. For this reason, it is usually best to wait until parts are complete before you use them to create an assembly, although this is rarely practical. n Use a degree-of-freedom analysis to prevent mates from becoming over-defined.
Tutorial: Mating for Success In this tutorial, you will put together a model of a robotic arm to better understand some of the mate issues discussed in this chapter. Follow these steps to mate for success: 1. Open the part named Chapter 13 Robot Base.sldprt from the CD-ROM. 2. In the part document window, click the Make Assembly From Part icon, and click the cursor on the Origin of the assembly to place the part Origin at the assembly Origin. The part is automatically fixed in place. 3. Click Insert ➪ Component ➪ Existing Part/Assembly. Click the Browse button in the PropertyManager, and find the part called Chapter 13 Robot Tower.sldprt. This part contains a Mate reference to help you mount it to the base. If you bring the cursor near the big circular hole in the base, you can see the transparent preview of the tower snap into place. Click to accept this placement. Figure 13.20 shows this placement in progress. Notice that the cursor appears as a SmartMate cursor for the peg-in-hole mate. When the part is dropped, check the mate list to confirm that a Concentric and a Coincident mate have been applied by the Mate reference.
433
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 434
Working with Assemblies
FIGURE 13.20 A Mate reference being used to SmartMate a component
4. Open the part with the filename Chapter 13 Arm.sldprt in its own window, and click Window ➪ Tile Vertically. The part and the assembly should be open in adjacent windows. 5. Click the face inside the hole without the chamfer around it in the Arm part, as shown in Figure 13.21. Then drag it into the assembly to the cylindrical face inside the hole at the top of the Robot Tower part. The concentric SmartMate symbol should appear on the cursor. 6. Click the green check mark icon to accept the Concentric mate. Move the part to test that the mates are correct. 7. Click the Mate tool on the Assemblies toolbar. Expand the Advanced Mates panel and click the Width mate. 8. In the Width Selections box, select the two inner faces of the Robot Tower part, and in the Tab selections box, select the outer faces of the Arm part. The selection should look as shown in Figure 13.22.
434
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 435
Getting More from Mates
FIGURE 13.21 Displaying a SmartMate when dragging between windows
Drag the inner face of the hole
9. Open a Windows Explorer window, and select the following parts: Chapter 13 Robot Arm2 and Chapter 13 Robot Gripper. Drag these parts into the SolidWorks assembly window, and drop them in a blank space. 10. Select the chamfered faces of the Arm and Arm2 parts and create a Coincident mate between them. You can make Coincident mates between conical faces as long as the cones are the same angle. This special case acts like a combination of Concentric and Coincident mates. Figure 13.23 shows the selections and the results.
435
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 436
Working with Assemblies
FIGURE 13.22 Creating a Width mate
FIGURE 13.23 Making conical faces coincident
Select these faces
436
20_080139 ch13.qxp
3/26/07
3:54 PM
Page 437
Getting More from Mates
11. Create a copy of the gripper part so that there are two instances of it in the assembly. You can do this by Ctrl-dragging the part within the assembly window. 12. Mate both of the grippers to the Arm2 end using the same mating technique that you used for the previous conical face Coincident part. 13. Once you have applied these parts, try moving the various joints of the assembly. Notice that it is difficult, if not impossible, to isolate the motion of just a single part. This is because there are too many open degrees of freedom, and a lot of ambiguity. 14. Fix Arm2 to allow you to move the gripper parts as you want. Create a Symmetric mate between the indicated faces of the grippers and the Front plane of the Arm2 part, as shown in Figure 13.24.
FIGURE 13.24 Creating a Symmetric mate
Faces for symmetric mate
15. Practice making angle mates, suppressing mates, and fixing parts to limit motion. 16. Save the assembly and exit the file.
437
13
20_080139 ch13.qxp
Part III
3/26/07
3:54 PM
Page 438
Working with Assemblies
Summary A thorough understanding of mates, and editing and troubleshooting techniques in particular, makes the difference between a real assembly artist and a user who struggles through or avoids certain tasks. There is a lot about mates that is not simply straightforward, but with practice, you can understand and master them. You can put assemblies together quickly, with a focus on rebuild performance and Dynamic Assembly Motion. Although best practice concepts should not dominate your designs, they are great guidelines to start from. Watch out for the pitfalls outlined in the Summary of Mate Best Practices section in this chapter to avoid making big mistakes.
438
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 439
Assembly Configurations and Display States
A
ssembly configurations enable you to control many things, including part configurations, suppression, visibility, color, and assembly feature sizes. They also allow you to control assembly layout sketch dimensions, mate values, suppression states, and several other items. What you will learn in this chapter about assembly configurations builds on the information in Chapter 10, which discussed part configurations. In this chapter, design tables will also be expanded upon to show how they are used in conjunction with SolidWorks assemblies. The Display States function was new in SolidWorks 2006. Display States are a better performance alternative to using configurations to control visibility of parts in assemblies. Display State options are discussed at length in this chapter.
Using Display States If you are using an older version of SolidWorks, then you may not have access to Display States, which were not introduced until SolidWorks 2006. They are a very useful addition to the software as they allow you to visualize the assembly in various ways. One of the best things about Display States is their ability to show parts in different display modes (Shaded, Wireframe, HLR, Shaded with Edges) simultaneously. Users have always been able to show parts transparent and shaded at the same time, and a common workaround for combining Shaded and Wireframe modes was to display the parts as Shaded with Edges, but to make some parts completely transparent. This would give the effect of some parts being shown in Wireframe mode. Because of Display States, this workaround is no longer necessary.
439
IN THIS CHAPTER Display States Assembly configurations Exploded views Tutorial: Working with assembly configurations
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 440
Working with Assemblies
Display States and configurations You can copy Display States between configs. To control the display, you can use the Display pane that flies out from the FeatureManager when you click the double-arrow icon in the upper-right corner of the FeatureManager. This is shown in Figure 2.1 in Chapter 2. Figure 14.1 shows the Display pane in action, along with an assembly showing parts in different Display States.
FIGURE 14.1 The Display pane and an assembly with parts in different Display States
The column symbols for the Display pane are as follows: Hide or Show state of the part Display Mode options for each component: Wireframe Hidden Lines Visible (HLV) Hidden Lines Removed (HLR) Shaded with Edges Shaded Default Display Component/Part Color (see Note) Component/Part Texture Component Transparency
440
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 441
Assembly Configurations and Display States
The difference between a component and a part in SolidWorks assemblies is that a component is a generic way of identifying any top-level item in an assembly, and may be a single part or a subassembly. It always refers to a specific instance of the part within the assembly. In the case shown in Figure 14.1, the gripper jaw part is used twice, and so there are two instances of the gripper jaw. One instance has its component color set to yellow, and the other instance uses the part color. (The component color is also referred to as an override of the part color). The part color is what you see when you open the part in its own window. The component color is only set in the assembly, and you can only see it in that particular assembly; it never affects how the part displays in any other assembly that the part is shown in.
NOTE
When there is a difference between the part and component properties (when an override exists), the component property appears as the upper-left triangle, in the color column of the Display Pane and the part property appears as the lower-right triangle. You can only see these triangles in the Color and Texture columns.
Color hierarchy is discussed in Chapter 3, but I will briefly summarize it here, showing the lowest priority at the top: n Part n Body n Feature n Face n Component If you override a color, display mode, or texture for a component in a subassembly, and the upperleft triangle appears in the Display pane, then you can remove the override through either the Left Mouse Button (LMB) or Right Mouse Button (RMB) menu. Figure 14.2 shows the LMB menu from a component of a subassembly with overrides.
FIGURE 14.2 You can remove overrides in the Assembly Display pane.
When you select Clear Override, SolidWorks clears any overrides for the currently selected subassembly component. Clear All Top Level Overrides clears all overrides in all subassemblies in the entire top-level assembly. There is no intermediate option to clear all top-level overrides for a particular subassembly; if you want to distinguish between overrides at that level, then you need to clear several individual overrides. The options to remove overrides do not affect top-level components.
441
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 442
Working with Assemblies
The active Display State appears in angle brackets after the configuration name and the filename at the top of the FeatureManager, as shown in the image to the left in Figure 14.3. Display States are created and managed in the ConfigurationManager, in folders under the configuration name, as shown in the image to the right in Figure 14.3. To create a new Display State, simply right-click the Display State folder under the active configuration and choose Add Display State. You can manage Display States in a way similar to the way in which Exploded Views are managed.
FIGURE 14.3 Display States shown in the FeatureManager and the ConfigurationManager
New configurations are always created with a default Display State named Display State-1, just as parts always have a default configuration named Default. To copy the New Display State shown in Figure 14.3 from the Default configuration to Configuration 2, you can Ctrl-drag it from one Display State folder to the other configuration’s folder. Display States offer a huge performance gain over configurations when used to control display of parts. The reason for this is that SolidWorks saves some model information for each configuration. In the past, configurations were sometimes created only for display purposes, and changing configurations required reading the model geometry again. When a configuration is created only for the purpose of hiding or coloring a part, this takes up a lot of additional file space and CPU time. Display States change much faster than configurations, almost instantaneously, and they add very little file size to use.
PERFORMANCE
Display States and drawings Display States can be shown on drawings if you have set the view to a Shaded Display mode. If you set the view to a Wireframe mode, then SolidWorks ignores the Display State, and all of the parts in the view display in that mode. Drawing views are discussed in depth in Chapter 21.
442
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 443
Assembly Configurations and Display States
Understanding Assembly Configurations Assembly configurations are used for many different purposes, including assembly performance, simplified assemblies, variations of assemblies, assemblies in different positions or states, and many others. Like part configurations, assembly configs also have a few best practice type suggestions. Configuration settings for assemblies control how the assembly appears in a Bill of Materials (BOM), what happens to parts, features, or mates that are added to other configurations, and so on. All of these are discussed in this section.
Configurations for performance One of the best tools to make large assemblies easier to work with is assembly configurations. You can use several techniques to improve the speed of working with assemblies. Although this information is presented in a list of techniques, it is important to select a method that fits the situation.
Suppressing components and features The most obvious use of configurations for improving assembly speed is to have a configuration or several configurations with suppressed components. One thing to watch out for when doing this is that configurations are not used in the place of subassemblies. If subassemblies are appropriate for the task, then you should use subassemblies. If not, then you should group and suppress parts using configurations.
TIP
Remember that you can use a folder for parts and suppress the folder.
Schemes that you may want to use for suppressing parts are to have configurations that isolate functional areas of an assembly, configs that remove the fasteners or purchased components, configs that remove complex parts, configs that only leave the parts used in in-context relations, configs that suppress patterns and assembly features, assembly configs that use simplified part configs, configs that show the assembly in different positions, or variations of the assembly using different part configurations. So many possible schemes for creating assembly configurations exist that it is pointless to try to list them all. Use your imagination, make sure that it makes sense, and give it a try. Avoid using fasteners to locate parts. The relationship should go the other way (fasteners should be located by the holes in parts). You should already have in place any parts that the fastener stack will touch before the fasteners are added. If parts added after the fasteners are either mated to the fasteners or the holes are created from the fasteners using in-context techniques, then suppressing the fasteners also suppresses the mates that locate those parts, and will cause problems with any in-context features.
TIP
If you suppress the “ground” part or any part that connects groups of parts, keep in mind that this can cause other parts to float in space, unattached to anything. Obviously this is not a good situation, and you should avoid it if possible. One way to avoid it is to use an assembly layout sketch and mate the parts to the sketch instead of to the ground part.
443
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 444
Working with Assemblies
Aside from components, other items can also be suppressed to improve performance, such as assembly features and component patterns. Do you really need to see all of those parts patterned around the assembly to work on it in a simplified representation? You may be able to suppress the parts. If you feel that you cannot suppress parts, then consider at least using Display States to hide parts that are needed to complete the parametrics but do not need to display. The biggest killer of assembly speed is the dreaded circular reference. You can make circular references in a couple of different ways, but they are usually the result of mixing history-based functions (mates, in-context sketch relations, feature references) with non-history-based functions (parts shown in the Assembly FeatureManager). This allows you to create partial or complete loops of references, where A references B which references A. These are a particular problem with in-context references, which are discussed in more depth in Chapter 16.
PERFORMANCE
Using part configurations for speed I have discussed simplified part configurations in Chapter 10, and they can consist of configs with cosmetic features such as small fillets and extruded text, or other cosmetic details that are suppressed. Assembly configurations can use different part configurations, which, for example, would enable you to make an assembly config called “Simplified,” and in it reference all of the Simplified part configurations. When opening an assembly through the Open dialog box, the Advanced option enables you to open the assembly and create a new assembly configuration that uses part configurations of a given name, if available. The default part configuration name entered in the text box is, I think, suggestive of how SolidWorks intended for this function to be used. As shown in Figure 14.4, it is “Simplified.”
TIP
Other special operations for assembly configurations in the Open dialog box include creating a new configuration that has all of the components suppressed. This allows you to see the structure of the assembly without fully resolving all of the components. Another option is to open the assembly with a new configuration, where all of the components are resolved. Beyond that, the Open dialog box also allows you to select a specific configuration to open to so that you do not have to wait for the last saved config to load and then make the change. When you use a part that has several configurations in an assembly, you cannot edit the part in the assembly unless the active configuration is the same as the config used in the assembly. This has always been the case. What is new about SolidWorks 2007 is that if you open the part in its own window from the assembly, SolidWorks automatically makes the config that is used in the assembly the active config. As a result, to change the active config and edit the part in the assembly, all you have to do now is to open the part in its own window and then switch back to the assembly (using Ctrl+Tab).
NEW FEATURE
Advanced Show/Hide It is curious that this option is not so easily available after the assembly is already open. However, you can use some other techniques to sort through parts. The Advanced Show/Hide Components dialog box is shown in Figure 14.5. You can access this dialog box by right-clicking the configuration name in the ConfigurationManager.
444
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 445
Assembly Configurations and Display States
FIGURE 14.4 The Advanced option for assemblies in the Open dialog box
FIGURE 14.5 The Advanced Show/Hide Components dialog box
445
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 446
Working with Assemblies
This tool enables you to establish search criteria and show or hide parts, based on the criteria. Multiple criteria can be used, stored, and retrieved. This tool is generally underused, and in my experience, users are always surprised to find it in the software. It has been there since about 1998. A function called Isolate is new to SolidWorks 2007. This works like the inverse of the Show command. If you select multiple parts and click Isolate from the RMB menu, the selected parts remain shown, and everything else becomes hidden. A little pop-up gives you the option of showing the removed components in a Wireframe or Transparent display mode, or of saving the current display as a new Display State. This is a very useful function, as shown in Figure 14.6.
NEW FEATURE
FIGURE 14.6 The Isolate function
SolidWorks Utilities Simplify Assembly If you have the SolidWorks Office bundle or higher, then you can activate the Utilities add-in. You can do this by selecting Tools, Add-ins, and then turning on Utilities. This displays a Utilities menu with the Simplify option. The Simplify Assembly tool is shown in action in Figure 14.7. The Simplify Assembly tool can find features in the parts of the assemblies that are under a certain size or that take up less than a certain percentage of the volume of the part. You can then suppress these features in special derived configurations.
446
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 447
Assembly Configurations and Display States
FIGURE 14.7 The Simplify Assembly tool
Controlling display performance Overall, SolidWorks performance is split into two categories: CPU (central processing unit) processing and GPU (graphics processing unit) processing. This is essentially the difference between calculating the parametrics and geometry, as opposed to the graphics and display. Which of these functions your computer performs better can vary widely, depending on your hardware, drivers, and system maintenance, among other factors. When trying to speed up the performance of an assembly, the biggest impact is obviously made if you can reduce the load on both the CPU and the GPU. You can do this by suppressing a part. When a part is suppressed, it is neither calculated nor displayed, and so the load on each processor for that part is zero. When you hide a part, its parametric features are still calculated by the CPU; however, because the part is hidden, it creates no load on the GPU. If you have a good main processor and a questionable video card, then you will achieve a greater benefit from removing graphics load from your display.
Lightweight parts On the other hand, if you want to still show a part but not calculate any of its parametric relations, then you should use Lightweight parts. You can find Lightweight default settings in Tools ➪ Options, on both the Assemblies and Performance pages. You can make parts lightweight through the RMB menu. The opposite of Lightweight is Resolved. Resolved means that the part is fully loaded, its parametrics are loaded and calculated by the CPU, and its graphics display data is calculated and shown by the GPU.
447
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 448
Working with Assemblies
To summarize this section, there is a four-way relationship between the Resolved, Lightweight, Hidden, and Suppressed states, as shown in Figure 14.8.
FIGURE 14.8 The relationship between the Resolved, Lightweight, Hidden, and Suppressed states
Resolved all parametrics and display data fully loaded
Hidden
Lightweight
parametrics loaded
parametrics not loaded
graphics data not loaded
graphics data loaded
Suppressed no parametrics or display data loaded
Resolved versus unsuppressed The terminology becomes a little convoluted here because of the relationship between the four different states. In parts, the feature states are easy to remember because features can be either suppressed or unsuppressed. However, in assemblies, there are four states instead of two, and so unsuppressed could mean anything that is not suppressed, which still leaves three states. For this reason, resolved is used instead of unsuppressed when dealing with components in an assembly.
Configurations for positions When you use configurations to display an assembly in various positions, you can do this in a couple of ways: by changing mates or by changing a layout sketch. Mates are configurable in two ways: mates can be suppressed and unsuppressed, and angle and distance mate values are configurable in the same way that sketch dimensions are configurable. Although creating a mate scheme that enables you to reposition the assembly using mate suppression states and values is essential to this method, it may not be the best approach. Using a skeleton or layout sketch to mate parts to may be a better approach, although this also has its drawbacks. If you mate to a layout sketch, you cannot make use of Dynamic Assembly Motion. If you use the mate scheme discussed above, this generally means having a fully defined assembly, and this also does not allow for Dynamic Assembly Motion.
448
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 449
Assembly Configurations and Display States
As a compromise, a good way to handle this is by using one configuration for Dynamic Assembly Motion, with one or more open degrees of freedom. You can use other configurations to fully define the mechanism and show it in particular positions using either method. Probably the best way to demonstrate this is with an example using the robot arm assembly.
Positioning with mates First, let’s take a look at positioning with mates. On an assembly such as this one, the goal is to position the grippers. You can do this in a couple of ways, both directly and indirectly. In the assembly used for this chapter, the grippers have been rebuilt as a subassembly, which allows different types of control. Notice that the subassembly has a configuration for the closed position and one that allows Dynamic Assembly Motion. Also, the subassembly is being solved as Flexible. Figure 14.9 shows the assembly and the FeatureManager.
FIGURE 14.9 The assembly used for this example
Driving the position directly A sketch point has been added to the subassembly to precisely identify the point on the gripper that is to be positioned. Sketch points have also been added to the main assembly to represent parts that need to be picked up by the robotic arm.
NOTE
For a better range of motion, this arm should probably have an additional pivot that enables motion out of the plane of the Tower part.
Check the derived configurations under the default config. Notice that when you switch between certain configurations, the parts seem to separate. Moving one of the links causes the parts to snap back together again. This is probably because there are so many options when moving between configurations that the software has difficulty choosing a final position. This is definitely one of the potential problems when using configured mates to show an assembly in various positions.
449
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 450
Working with Assemblies
Notice also that although the grippers are positioned correctly, the arm is still allowed to swivel around the intended target point. You can correct this by defining an orientation for the grippers for each location. If the additional pivot were added to the assembly, then fully defining the parts would become more difficult. The arm would not be able to reach any additional points, but it would not be so limited in orienting the grippers at each point.
Driving the position indirectly You can also use mates to drive configured positions of the assembly using a series of angle mates. This makes it more difficult because to get to a particular location, you have to do some calculations, but the angle mates appear to be more stable than simply relying on moving the parts to unconstrained positions. If you cycle through the derived configurations under the Indirect top-level configuration, notice that mates are not suppressed and unsuppressed, rather the values are changed. This makes it somewhat more difficult to precisely position the grippers, but because it is specific about the positions of the individual parts, there is no ambiguity.
Positioning with sketches Although this technique is still using mates to position the parts, to change the position, you change sketch dimensions rather than mate values. Sketches used to drive parts from an assembly are sometimes called layout sketches or skeletons. These are also discussed in Chapter 16 for in-context or top-down assembly techniques and Chapter 11 as a way of controlling parent/child relationships. Figure 14.10 shows the same assembly that is used for the rest of this chapter.
FIGURE 14.10 Positioning assembly components with sketches
450
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 451
Assembly Configurations and Display States
This particular assembly is driven by two sketches on different planes to govern the position of the parts. Keep in mind that this assembly has been used for all of the other techniques as well, and so all of these techniques can exist together simultaneously, being controlled by configurations. Examine the assembly to see how the parts are mated to the sketches. This is important. The first time you create a part such as this, you may be tempted to mate part planes to the sketch lines. Mating planes to sketch lines has a very serious drawback that you must be aware of. Unlike other types of mates, which have an alignment that you can control, plane-tosketch line mates cannot be aligned. This means that the software is as likely to align elements correctly as incorrectly on any plane-to-line mate.
CAUTION
BEST PRACTICE
A better way to mate part planes to sketch lines is to mate the Temporary Axes through the joints with the sketch endpoints. This solves the alignment problem.
Configurations for product variations In this case, product variations means variations in size or part replacement. Some examples are a 4-foot cabinet and an 8-foot cabinet, or a two-button mouse and a three-button mouse. As a simple example, Figure 14.11 shows the familiar robotic arm assembly, but with a variation: one of the arms has been replaced with a subassembly. The subassembly is made of the original replaced part using configurations, and there are configurations of the subassembly, which is again being used as a flexible subassembly.
FIGURE 14.11 A part that is replaced by a subassembly
451
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 452
Working with Assemblies
Through the course of this chapter, the robot arm assembly has greatly increased in complexity, but it has retained the original information that was in the first version. Maintaining valid assembly data through manually managed configurations is difficult, and all it takes is a simple mistake to wipe out a lot of assembly configuration data. Appropriately, the next section discusses assembly design tables.
Design tables for assembly configurations Chapter 10 dealt with part configurations and created a good framework for design tables in general. This chapter augments that information with what you need to know to use design tables effectively in assemblies. Assembly design tables can do everything that part design tables can do, except for selecting configurations of base parts and split parts, which are not valid assembly functions. Assembly design tables can also do some things that a part design table cannot. These include: n Assigning the Display State for a configuration n Suppressing the state of a part (R for Resolved or S for Suppressed) n Assigning the component configuration for the assembly config n Allowing you to activate the Never Expand in BOM option If you have been using design tables for a while and are familiar with older versions, then you may have noticed that the $show parameter, which specified whether the part was shown or hidden, has become obsolete due to the new functions of Display States. Figure 14.12 shows the design table that results from auto-creation using the robot arm assembly. Some of the columns have been hidden to make it small enough to fit on the page. If you want to see the entire table, you need to open the assembly. If you edit the design table, then you will probably want to use the Open in Separate Window option, which is easier to navigate and control.
FIGURE 14.12 An auto-created design table from the robot arm assembly
452
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 453
Assembly Configurations and Display States
Assembly configuration dos and don’ts n Avoid using Delete as an editing option when working with configurations. Delete is forever and for all configs. n Avoid the use of in-context relations to size parts when you are also using configurations to size parts. A non-configured part driven by a configured part only causes confusion. n Avoid using configurations to represent document control type revisions. I have seen people attempt to do this, but in the end, it limits the kinds of edits you can make to your parts and assemblies, and it is far too easy to make a mistake that wipes out all of your diligence. In the end, this is not a viable technique. n If you are working with manually created configs, then you should create a new configuration and activate it before making the changes. Otherwise, you will end up trying to set the original config back to the way it was. n Remember to select the This Configuration Only option for changed dimensions, instead of leaving it at the default All Configurations setting.
Creating Exploded Views Exploded views enable you to display an assembly taken apart so that you can see all of the parts. They are great for assembly documentation, assembly instructions, and for visualizing assemblies with concealed internal parts. I have included exploded views in the assembly configurations chapter because, like Display States, exploded views are found in the ConfigurationManager under the configuration. Each config can have multiple exploded views, and you can copy exploded views between configurations. When you are creating the exploded view of the top-level assembly, and a subassembly already has one, you can include the subassembly’s exploded view in the top-level exploded view. While you are creating exploded views, mates are temporarily suspended. To initiate a new exploded view, switch to the ConfigurationManager, RMB click a configuration name, and select New Exploded View, as shown in Figure 14.13. Figure 14.13 also shows the Explode PropertyManager interface. This interface includes a helpful How-To section at the top to give you a hint of where to start. If you are creating assembly instructions or an animation from the exploded view (using Animator or the RMB options, Animate Explode, or Animate Collapse), then you may need to be more careful about how the parts are exploded. You can create explode lines that show how the parts go back together.
453
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 454
Working with Assemblies
FIGURE 14.13 Initiating a new exploded view
To begin, you can explode the Base and the Tower down and back, respectively. A single part can explode in multiple directions, or multiple parts can explode in a single direction. These two parts are shown exploded in Figure 14.14. Select the base, and then drag the arrow of the Triad that moves in the direction that you want the part to move.
454
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 455
Assembly Configurations and Display States
FIGURE 14.14 Exploding the base
The Tower part is a little more difficult because it is not lined up with the direction in which it needs to be exploded. To remedy this, highlight the Direction box in the PropertyManager and select a face that is normal to the direction that you want to drag, or an edge that is in this direction. Then drag the appropriate arrow on the triad again, as shown in Figure 14.15. SolidWorks Help says that you can drag the sphere of the triad onto a face to change the direction, rather than selecting a face in the Direction box. However, it fails to mention that you have to hold down the Alt key while dragging it, in order for it to stick to an entity.
TIP
Exploding the Twist Arm subassembly provides the opportunity to show a couple of useful subassembly functions. You can explode the parts of a subassembly either together as a unit or individually. You can even reuse explode steps from the subassembly, which is what you will do here.
455
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 456
Working with Assemblies
FIGURE 14.15 Changing the direction of the explode
Direction box
To explode the subassembly as a single part and then reuse its explode steps from the subassembly file, ensure that the Select Sub-Assembly’s Parts option is off, as shown in Figure 14.16. You cannot reuse a subassembly’s explode steps if the subassembly is set to Flexible. SolidWorks will tell you that there are no explode steps to reuse if you try to reuse the explode steps of a flexible subassembly. In order to work around this, you can set the subassembly to solve as Rigid, reuse the explode steps, and then set the subassembly back to Flexible. Although awkward, this is an effective workaround to this problem.
CAUTION
While exploding the parts, you should rotate the view from time to time. Unless you are creating the explode for a particular point of view, the explode may look very different if you rotate it a little.
TIP
For the final explode step, the grippers will explode individually in opposite directions. Remember that these parts belong to another subassembly. If you create an explode step with the Select SubAssembly’s Parts option turned off or on, you will not be able to change it later, and so you need to pay careful attention to what you are doing. Turn on the Select Sub-Assembly’s Parts option, select one gripper, Alt-drag the triad to set the direction, and then drag the distance of the explode. If you are in the mood to submit an enhancement request to SolidWorks, then you may want to request a Symmetrical Explode function for situations such as this. Figure 14.17 shows the finished result of the explode.
456
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 457
Assembly Configurations and Display States
FIGURE 14.16 Exploding a subassembly
FIGURE 14.17 The finished explode
457
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 458
Working with Assemblies
You may have noticed that each explode step creates a dashed line to show where the explode came from. Unfortunately, these dashed lines cannot be turned into usable explode lines on documentation. You must create explode lines manually, using 3D sketches. Although 3D sketches can be very tricky to use, for this purpose, you can limit their function to simple straight lines. As long as you try for simple results, the Explode Lines feature should work well. Before I begin to discuss the Explode Lines feature, we should take a minute to look at the terminology, which can be confusing. For example, the opposite of explode is collapse. Unfortunately, the opposite of expand is also collapse, and so when the assembly is exploded and you want to collapse it, the RMB menu on the Exploded View displays one entry called Collapse and another called Collapse Items. You must remember that Collapse Items refers to expanded ConfigurationManager lists, while Collapse refers to un-exploding the Exploded View. Another example is that the PropertyManager and Tooltips call the function Route Line (which can be easily confused with a function of the SolidWorks Routing software), but on the toolbar and menu, it is referred to as Explode Sketch. Further, the tool that you use to start the Explode Sketch function is on the Explode Sketch toolbar itself, and does not seem to exist on any other toolbar. You must access it from the Insert menu, by selecting the command called Explode Line Sketch. Figure 14.18 shows some examples of the above-mentioned terminology.
FIGURE 14.18 Interface and terminology inconsistencies in the exploded view and Explode Line functions
To initiate the Explode Line Sketch function, you can select Insert ➪ Explode Line Sketch. This displays the Explode Sketch toolbar and the Route Line PropertyManager interface. Creating nice explode lines takes a little practice, but it is easiest with circular parts, or circular features on parts with other shapes. Selecting circular edges makes the line start from the center of the circle. If after you have selected two circular edges, the explode line goes the wrong way, you can click the arrow at the start of the line. Notice in Figure 14.19 that the line seems to take an unnecessarily circuitous route. This is because the explode directions were not square to the assembly Origin. To work around this problem to some extent, you can deselect the Along XYZ option in the Route Line PropertyManager. You can move the jogs by bringing the cursor close to the line, and selecting the arrows that pop up.
458
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 459
Assembly Configurations and Display States
FIGURE 14.19 Redirecting explode lines
Figure 14.20 shows the difference between using the Along XYZ option (image to the left) and turning it off when the explode was not square to the assembly Origin (image to the right).
FIGURE 14.20 The Along XYZ option, selected and deselected
The completed explode lines are shown in Figure 14.21. You can animate the explode or collapse from the RMB menu. To do this, right-click the exploded view, and select Animate Explode or Animate Collapse. This method does not offer recording or Photoworks rendering like Animator software, but it is fast and easy.
459
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 460
Working with Assemblies
FIGURE 14.21 Completed explode lines
Tutorial: Working with Assembly Configurations To begin this tutorial, open the assembly named Chapter 14 Bike.sldasm. This assembly is made from the same parts as the assembly that was used in Chapter 12, but it will be used differently here. This file contains all of the aspects that we need to work with in this chapter, including subassemblies, motion, and part configurations.
NOTE
You can ignore the warning symbols in the BibleBikeFrame part file. These are caused by the Fill feature that is discussed in Chapter 27.
To learn how to work with assembly configurations, follow these steps: 1. Prepare to use configurations by splitting the FeatureManager window into an upper and lower pane. Place the FeatureManager on the top and the ConfigurationManager on the bottom. 2. Before starting to make changes to this assembly, add the top-level configurations that you will need, as follows:
n Small Tires n Motion Configuration
460
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 461
Assembly Configurations and Display States
n Skeleton Driven Positions n Mate Driven Positions The configurations will list alphabetically. 3. Make sure that the Advanced Options of each configuration are set to Suppress New Features And Mates and also Suppress New Components. 4. Activate the Small Tires configuration. Figure 14.22 shows the FeatureManager up to this point.
FIGURE 14.22 The FeatureManager and ConfigurationManager up to step 4
5. Open the Front Wheel Assembly in its own window and switch to the ConfigurationManager. Add a configuration called Small Tires, and change the tire to the configuration called Small Tire, which has already been created. 6. Switch back to the main assembly window (using Ctrl+Tab), RMB click the Front Wheel Assembly in the FeatureManager, and select Component Properties. Select the Default configuration for the Front Wheel assembly, as shown in Figure 14.23.
461
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 462
Working with Assemblies
FIGURE 14.23 Changing the tires in the Component Properties dialog box
7. Repeat steps 4 to 6 for the Rear Wheel assembly. 8. Double-click another configuration from the list and watch the assembly change from small to fat tires. 9. Change to the Motion configuration. RMB click the Stem-Fork assembly, select Component Properties, and set the assembly to be solved as Flexible. 10. Exit the dialog box and check to see that the fork linkage mechanism moves by dragging the fork. Notice that the fork works but that the front wheel does not move with it. The bike design is not yet complete, and so you do not need to worry about that at this point. 11. Switch to the Skeleton Driven Positions configuration. 12. Display the assembly Layout Sketch at the top of the FeatureManager. 13. Create two new derived configurations under the Skeleton Driven Positions configuration, one called Default Position and the other called Compressed Position. 14. Activate the Default Position configuration, and make a coincident mate between the Top plane of the Chainstay part and the sketch line indicated in Figure 14.24. 15. Activate the Compressed Position configuration and make a coincident mate between the same plane and the line that is angled up at 10 degrees. For these configs you also need to set the Advanced options just as you set the top-level configs in step 3. If you do not do this, then you may need to manually suppress the unwanted mates in the appropriate configurations.
NOTE
462
21_080139 ch14.qxp
3/26/07
3:56 PM
Page 463
Assembly Configurations and Display States
FIGURE 14.24 Positioning the rear of the bike
Mate to this line
16. Switch to the Mate Driven Position configuration. 17. Add new derived configurations called 1, 2, and 3. While creating the new configs, ensure that the Suppress New Features and Mates and Suppress New Components options are selected. 18. Make an angle mate between the Bike assembly Top plane and the face of the link, as shown in Figure 14.25.
FIGURE 14.25 Using angles to position the fork
463
14
21_080139 ch14.qxp
Part III
3/26/07
3:56 PM
Page 464
Working with Assemblies
19. Once the mate is complete, double-click the angle dimension (you may have to doubleclick the angle mate to get it to display and then zoom out to see it), and change the value to 18 degrees.
NOTE
You need to set the Fork assembly to solve as Flexible for each configuration. You may also need to control the alignment for the angle mate manually for each configuration.
Summary Display States in the assembly can save a lot of time because they change faster than configurations and offer more options for visualization, including mixed display modes. You can save and copy multiple Display States between configurations. Assembly design tables can select Display States and drive many other parameters in assemblies. The Exploded View functionality in SolidWorks has some unusual aspects that you need to work around; however, it is a valuable and useful function, and is worth the extra steps.
464
22_080139 ch15.qxp
3/26/07
3:58 PM
Page 465
Component Patterns
I
n SolidWorks assemblies, the word component can refer to either parts or subassemblies at the top level of an assembly. Component patterns can therefore be patterns of parts, subassemblies, or combinations of parts and subassemblies.
IN THIS CHAPTER Local component patterns Derived component patterns
best pattern performance, you should use subPERFORMANCE For assemblies as the patterned unit as much as is practical. Multiple patterns of individual components are not as efficient as a single pattern of multiple components. A single pattern of a single component, where the single component is itself a subassembly, is the best choice, if available. Another performance issue is the fact that component patterns require external references (for the direction or center of the pattern). These external references have the potential to increase rebuild times if you do not choose them carefully. Although you can experience possible performance problems with patterns, they can also significantly decrease the number of mates in an assembly, which always improves performance.
Component patterns come in two varieties: local patterns, which include linear and circular patterns, and derived patterns, which are driven from a feature pattern in a part. The local patterns are obviously somewhat limited, but because derived patterns follow patterned features, they can also be driven by sketch-driven patterns. Curve-driven and fill patterns cannot be used. It is possible to focus only on the basics, to simply be able to make patterns that exist in the present moment. However, if you are interested in creating features that will adapt to future changes, then you will find this chapter useful.
465
Other pattern options Tutorial: Creating component patterns
22_080139 ch15.qxp
Part III
3/26/07
3:58 PM
Page 466
Working with Assemblies
Using Local Component Patterns Local component patterns are limited to linear and circular patterns. The linear pattern directions work just like the linear pattern feature in parts, and must reference a line, axis, edge, and so on to establish the direction. In an assembly, this means that the feature uses model geometry from a part (solid or surface edges, sketches, reference geometry), an assembly sketch entity, or an assembly reference geometry entity (such as an axis). This is important to keep in mind if you are concerned about circular references.
BEST PRACTICE
If you have a feature pattern in a part, you should take advantage of it and use a driven pattern instead of a local pattern.
Local pattern references If you still need to create a local pattern, it is best to use a reference that is not dependent on part geometry. Remember that when part geometry is used for this purpose, the parts must be solved first (sketches and features rebuilt), then the mates must be solved (to position the parts), then any in-context references must be solved (which may change the part geometry), and then any assembly features or component patterns must be solved. As a result, it is best practice to use as pattern direction references, assembly sketches that do not reference anything else. The assembly sketches should sit at the top of the assembly FeatureManager to ensure that they are not picking up references from the history-based features in the design tree (mated components, patterns, assembly features, and so on). When a local pattern really requires a reference from a part, you have no alternative. However, if you can avoid this by using a sketch assembly skeleton to which the parts are mated and also used for the pattern references, then you should do so. At all costs, you should avoid using in-context features, assembly reference geometry that is dependent on part geometry, and assembly features for the local pattern reference. Figure 15.1 shows a sample organization of one way that you can set up an assembly to properly control local component patterns. The lines shown can be created in either two 2D sketches or a single 3D sketch. The lines are dimensioned from planes, which allows them to be angled for patterns that are not square to the coordinate system of the assembly, but still lie on its main planes. In most situations the rebuild time penalty of using model geometry to establish pattern direction is fairly slight. The sketch method is probably most justifiable in large, complex, assemblies, or in assemblies requiring long rebuild times. Figure 15.1 also shows the PropertyManager interface for the local pattern.
466
22_080139 ch15.qxp
3/26/07
3:58 PM
Page 467
Component Patterns
FIGURE 15.1 The Assembly FeatureManager for local component pattern setup
Notice where the pattern is placed in the FeatureManager. You can reorder the pattern feature in the design tree, but you cannot move it above the mates. Interestingly, you can move the sketches after the pattern, even though the pattern is dependent on one of the sketches. Obviously, SolidWorks is working with the order behind the scenes in such a way that the user cannot make mistakes.
Pattern Seed Only All of the aspects of the interface should be familiar, such as the direction, instances, and spacing. The Pattern Seed Only option is also used in feature patterns. Patterning the seed only is designed to allow you to create a single pattern in two directions that are separated by 180 degrees, where the internal instances do not overlap one another. For example, if
467
15
22_080139 ch15.qxp
Part III
3/26/07
3:58 PM
Page 468
Working with Assemblies
you take a basic two-directional pattern and change the angle between the directions so that they are anti-parallel (parallel but going in opposite directions), then all of the component instances that were between the two legs of the L created by the two directions will come to overlap one another when they are laid out in a straight line. Figure 15.2 shows how a 5-by-4 pattern with 20 instances becomes a 1-by-8 (the seed is not counted twice) pattern. When this happens, the other 12 instances are overlapping the remaining ones. When you use the Pattern Seed Only option, you are only patterning the two legs of the L, and not the instances in between. This can cause problems with BOMs and mass properties.
FIGURE 15.2 When to use the Pattern Seed Only option
468
22_080139 ch15.qxp
3/26/07
3:58 PM
Page 469
Component Patterns
Instances to Skip The Instances to Skip option for component patterns, shown in Figure 15.3, works just like the equivalent option for features. Click the dots in the graphics window to toggle each instance of the pattern.
FIGURE 15.3 The Instances to Skip option
Using Derived Component Patterns Derived component patterns have two main limitations: they cannot be driven from either curvedriven or fill patterns. The remaining pattern types that work with derived component patterns are linear, circular, sketch driven, and table driven. By their very nature, derived component patterns break some of the best practice suggestions in this book, because the pattern is driven by part geometry, and the part must first be solved (by solving features internal to the part) and then placed (by solving mates); only then can the derived pattern be solved. Still, I recommend using derived patterns over local patterns when available because of the parametric link. For the derived component patterns, the location of the initial component is important. You need to match the placement of the initial component with the position of the original feature from which the pattern was created, not one of the patterned instances.
NOTE
469
15
22_080139 ch15.qxp
Part III
3/26/07
3:58 PM
Page 470
Working with Assemblies
Figure 15.4 shows the PropertyManager interface for a derived component pattern.
FIGURE 15.4 The Derived Component Pattern interface
You can nest derived component patterns such that one component pattern is patterned by another component pattern, just like feature patterns. The second pattern can be a local pattern or a derived pattern.
Understanding Other Pattern Options Figure 15.5 shows the RMB menu for a component pattern.
FIGURE 15.5 The component RMB menu
470
22_080139 ch15.qxp
3/26/07
3:58 PM
Page 471
Component Patterns
Dissolve Pattern The Dissolve Pattern option removes the component instances from the pattern feature and puts them in the main part of the assembly FeatureManager. The components just become normal components in the assembly without the intelligence of the pattern feature placing them. The components are left in the assembly without any mates, simply floating in position.
Add to new folder You can add patterns to folders. If you have a list of patterns at the end of an assembly, it may make sense to group them into related folders for the purpose of organization. This is the same as using folders for features, mates, or components.
Component pattern display options The individual component pattern instances can have their color and other display options changed individually or collectively as a pattern feature. Figure 15.6 shows the display pane where you can control these display options.
FIGURE 15.6 The display pane for controlling display options
Component patterns and configurations Individual instances of the component pattern also enable you to control configurations. After you create the pattern, you can select individual instances and change their configs. This can be extremely useful if you have a mechanism subassembly shown in various positions, for example, patterned around an indexing dial.
471
15
22_080139 ch15.qxp
Part III
3/26/07
3:58 PM
Page 472
Working with Assemblies
Tutorial: Creating Component Patterns To learn how to create component patterns, follow these steps: 1. Open a new assembly. Create a new sketch on the Top plane, with two lines from the Origin out at odd angles so that they do not pick up horizontal or vertical automatic relations. 2. Apply dimensions between one of the lines and the Right plane, and set the angle to zero degrees. 3. Apply a second dimension to the other line from the Front plane, again with an angle of zero degrees. 4. Open the part from the CD-ROM named Chapter 15 Pattern Part.sldprt. This part already contains several features so that you can practice using derived component patterns. 5. Insert the part into a new assembly. Locate the part at the assembly Origin such that the part Origin matches the assembly Origin. 6. Open the part called Chapter 15 Patterned Part.sldprt, and place it in the assembly. Remember that it is important to match the part up with the original patterned feature, and not to just place it on any instance of the feature pattern. The original features are colored red in the part. Under normal circumstances, the patterned instances are the same color as the patterned feature because of the Propagate Visual Properties setting, which is turned on by default in all of the pattern feature types. For this part, I turned this setting off for each pattern feature so that the original feature could be a different color than the rest of the pattern.
NOTE
One notable exception to this is the Table Driven Pattern, which appears to have a bug: if you turn off the Propagate Visual Properties setting and exit the feature, it just turns it back on. In this case, the hole colors were changed by changing face colors rather than feature colors.
7. Place the part on one of the original features. Remember that Alt-dragging the circular edge on the flat side of the part allows you to SmartMate the part to the round holes. It cannot help you with the rectangular or hex holes. For these, it may be best to show the sketch for the holes and place the part with respect to the sketch entities. 8. Create feature driven patterns (Insert ➪ Component Pattern ➪ Feature Driven). Try to use each of the patterns from the pattern part. Notice that the fill pattern gives a specific error that it cannot be used for a derived pattern, but the curve-driven pattern does not. This may mean that in some situations you can use the curve-driven pattern to drive a component pattern, or it may just be another interface inconsistency. 9. Once you have created a few feature-driven patterns and have a better understanding of how it is done, you can create a local pattern (Insert ➪ Component Pattern ➪ Linear Pattern). 10. Select the sketch line that was drawn in the Z direction as the direction. 11. RMB click the top level of the assembly FeatureManager and select Collapse Items. Highlight the Components to Pattern selection box. Select the first part in the FeatureManager and then Shift-select the last pattern feature. This patterns everything in the assembly.
472
22_080139 ch15.qxp
3/26/07
3:58 PM
Page 473
Component Patterns
12. Make the spacing four inches with three instances. 13. Create a second direction using another of the sketch lines with six-inch spacing and four instances. 14. Notice how the preview shows 12 instances of the patterned assembly. Click the option for Pattern Seed Only and see how the preview changes to seven instances. Click OK to accept the feature. 15. Change the zero-degree angle in the sketch created in steps 1 through 3, to 30 degrees. You may have to press Ctrl+Q to get the assembly to update properly.
Summary Performance and best practice are both issues that require compromise. Patterns can cause a performance reduction because of the nature of the references. However, they can also improve performance because the need for extra mates is reduced and it is easier to simplify the assembly by suppressing the pattern feature. Derived patterns are driven by feature patterns, and transgress more best practice suggestions, but they also add a parametric link, which updates the component pattern automatically.
473
15
22_080139 ch15.qxp
3/26/07
3:58 PM
Page 474
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 475
Modeling in Context
I
n-context modeling offers a gateway to a world of expanded modeling possibilities in SolidWorks. The topic of in-context modeling is often a source of sometimes questionable advice and suggestions from even experienced users. In this chapter, I offer a balanced explanation with each suggestion so that you can evaluate the suggestion for yourself.
If you are well disciplined in your modeling practices, and understand the potential problems of in-context modeling, then you can avoid these problems. After one bad experience, some users focus on this experience, and fail to see the positive side of using in-context modeling. Although dangers do exist, they often result from disregarding the rules.
Understanding In-Context Design In-context modeling is also known as top-down modeling. It is a technique that is used to create relationships between two parts in an assembly, where the geometry of one of the parts is controlled by both the other part and the mates that position them relative to one another. In-context, or top-down, modeling may be contrasted against bottom-up modeling. Bottom-up modeling involves making the parts in their own individual windows and assembling the finished parts into an assembly with mates. In its most common form, a sketch in one part in an assembly is related to another part in the assembly. The relationship is specific to that particular assembly, and is only relevant in the context of that assembly. For example,
475
IN THIS CHAPTER Understanding in-context design Dealing with practical details of in-context modeling Other types of external references Tutorial: Working in-context
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 476
Working with Assemblies
you may create a box and put it into an assembly. You must then create a lid that is parametrically linked to the size and shape of the box. You can create a lid part in the context of the assembly such that the lid always matches the box. Sketch relationships, dimensions, and feature end conditions from the lid can reference the box. When the box changes, the lid also changes if the assembly is open. The assembly maintains a record of the reference. If the box is changed with both the assembly and the top open, then the top updates, but if the box is changed without the assembly being open, then the lid will not update until the assembly is opened. The record of the reference that the assembly maintains is held in what is called an update holder, and in recent versions, it is all but forgotten. Chapter 12 discusses in-context reference update holders. These are the pointers in the assembly that hold the reference information. These holders are hidden by default, and do not enable any real functionality, but they do serve as a reminder that the assembly has in-context references, and can be queried to tell you what parts the in-context relations go between.
CROSS-REF
Advantages of in-context modeling The advantages of in-context modeling are obvious. I spent the first couple of chapters of this book discussing the strengths of parametric design, and in-context modeling is just an extension of parametric techniques to include parts in the context of an assembly. Making a change to one part and having all related parts update offers indisputable advantages.
Potential problems with in-context modeling There may also be some issues that arise from this technique of driving changes from a different part model. There are no problems with the overall concept of in-context modeling; the problems occur with the practical application of the technique. In particular, the biggest problems seem to arise when in-context techniques are combined with other techniques. You must be very careful about file management issues when in-context references exist in your assembly.
Dealing with the Practical Details of In-Context Modeling Figure 16.1 shows a simple box with the sketch of a simple top for the box. Notice in the FeatureManager that two parts are listed as the Box Top and Box Bottom. The .050-inch offset is creating a sketch in the Top part that is driven by the edges of the Bottom part. This simple assembly demonstrates the in-context process in the sections that follow.
476
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 477
Modeling in Context
FIGURE 16.1 The top of the box being built in-context
The in-context process You can perform in-context modeling using one of two basic schemes. You can build parts from the very beginning in the context of the assembly (using the Insert ➪ Component ➪ New Part menu option) or you can start them using bottom-up techniques creating the parts in a separate part window, add them to the assembly, and then add additional in-context features later.
Starting out in-context To start a new part in the context of an assembly, we will first assume that the assembly contains another part. Creating a new part in a blank assembly is not very interesting. In this case, I am using the assembly shown in Figure 16.1. Once the first part is in the assembly, you must save the assembly before creating a new part in it. This is because the update holder needs to reference a particular filename, and the assembly has no filename until you save it. To create the new part, click Insert ➪ Component ➪ New Part. This command is also available through a toolbar button that you can place on the Assembly toolbar (it is not there by default). At this point, SolidWorks prompts you to first name the part, and then select a face or plane on which to locate the new part. The selected face or plane actually determines the Front plane of the new part, and a mate is added to the assembly.
The InPlace mate The mate that you are adding is called an InPlace mate. This works like the Fixed option, but is actually a mate that is listed with the other mates and that may be deleted, but not edited.
477
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 478
Working with Assemblies
The InPlace mate clamps the part down to any face or plane where it is applied. It is meant to prevent the in-context part from moving. I will explain later in this chapter why it is so important for in-context parts not to move. Although the InPlace mate clamps the part down, I have heard people report bizarre behaviors with the InPlace mate reportedly allowing parts to move unpredictably, but I do not put any stock in these reports. The cause of things such as this usually turns out to be a user who is not paying attention to what is going on. Software is a very deterministic system, where everything happens for a reason. However, if a face on which an InPlace mate has been created is moved by the part changing, then the in-context part could possibly move in a way that you might not predict. The problem is that while the Front plane of the in-context part is defined with respect to the selected face, it is not explicitly defined rotationally about an axis perpendicular to the face, or translationally about axes parallel to the face.
NOTE
Alternative technique If you are concerned about using the InPlace mate, then I would suggest an alternative technique. Instead of using the Insert ➪ Component ➪ New Part command, you should simply create a blank part and save it to the desired location. You can then insert the existing but blank part into the assembly and mate the three planes to the assembly or to the part, as appropriate. You can then edit the part in-context, the same as if you had created it in-context. The only difference between parts developed this way and parts created in-context is the InPlace mate. The InPlace mate cannot be edited and does not have relations to other geometry in the usual sense. Many people feel more secure with real mates to real geometry, which can be identified and changed if necessary.
Valid relations Sketches, edges, and faces from the other parts in the assembly can be referenced from the incontext part as if they were in the same part as the sketch. Most common relations are concentric for holes, and coincident for hole centers. Converted entities (On-Edge relations) make a lineon-edge relation between the parts, and Offset sketch relations are also often used. Other types of valid in-context relations include in-context sketch planes, and end conditions for extrude features such as Up to Face and Up to Body. Beyond that, you can copy surfaces from one part using the Knit Surface feature, or the Offset Surface feature. I discuss surfacing in more detail in Chapter 27.
Working in-context When working in-context or using in-context data, visual cues offer information about the part that you are working on. The following topics are all meant to help you understand what is going on.
478
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 479
Modeling in Context
Text color When modeling in-context, the FeatureManager text of the part that you are working on turns blue. This should make it immediately obvious first that you are working in-context, and second, which part is being edited.
Part color and transparency Color and transparency behavior of parts in the assembly where a part is being edited in-context can be controlled through the Tools ➪ Options ➪ Colors page. Figure 16.2 shows a detail of this page. Appendix B discusses Tools ➪ Options settings in more detail. The option at the bottom of the dialog determines whether the colors specified in the list at the top are used or ignored. If they are ignored, the parts retain the same colors as if you were not using in-context techniques.
FIGURE 16.2 Part-color settings for in-context control
Settings that control in-context editing colors
An additional setting in Tools ➪ Options is found on the Display/Selection pane. Here, you can control the transparency of the parts not being edited. Figure 16.3 shows this setting.
479
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 480
Working with Assemblies
FIGURE 16.3 Part transparency for in-context control
In-context part color transparency control
The options in the Assembly Transparency drop-down list are: n Opaque Assembly: All parts that are not being edited when an assembly component is being edited in-context will turn opaque, even if they are otherwise transparent. n Maintain Assembly Transparency: Leaves all assembly components in their default transparency state. n Force Assembly Transparency: Forces all of the parts, except for the one being edited in the assembly, to become transparent. These options reflect personal preference more than anything else, but it is useful to have a reminder as to whether a part is being edited in the assembly or the assembly document is being edited in its own window.
TIP
The color selected in the box shown in Figure 16.2 controls both the text color and the color of the part shown in the graphics window.
Edit Component button You can use the Edit Component button in two ways. First, after you have created a part incontext, seeing the Edit Component button depressed serves as a reminder that you are editing the part rather than editing the assembly. Along with the part color and transparency displays, this is important because assembly functions such as mates, exploded views, and others are not available when you are editing the part.
480
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 481
Modeling in Context
The second use of the Edit Component button is to begin or finish editing a part that is already in an assembly. When you are editing a part in the context of an assembly, the title bar of the SolidWorks window reflects the fact that you are editing a part in an assembly, the toolbar changes to a part-editing toolbar, and the lower-right corner of the taskbar displays the words Editing Part, as shown in Figure 16.4.
FIGURE 16.4 Indicators that you are editing a part in-context
Editing a component can also mean editing a subassembly in the context of the top-level assembly. You can create in-context assembly features and mates if necessary. This is done far less frequently than editing parts in-context. Creating in-context relations is not the only reason to edit a part or subassembly in the context of the top-level assembly. Sometimes it is simply more convenient to do normal editing when you are in the top-level assembly, so that you can see how the part relates to other parts after making changes in the assembly without making relations between the parts.
NOTE
Editing a subassembly in the context of the upper-level assembly is often useful as well, to see how changing subassembly mates affects the top level.
Probably the most common mistake that users make around the issue of editing the part versus editing the assembly is when they add a sketch. If you intend to add a sketched feature to a part in the context of an assembly, but you fail to switch to Edit Part mode before creating the sketch, then the sketch ends up in the assembly rather than the part; you can only do limited things with a sketch in an assembly. Likewise, if you intend to make an assembly layout sketch, but you do not switch out of Edit Part mode, then you end up with a sketch in a part that cannot do what you want it to do.
External reference symbol The external reference symbol appears as a dash followed by a greater-than sign. External references do not only indicate in-context features. You can also create external references by using the Split Part command as well as the Insert Part (base or derived part) or the mirrored part functions. Figure 16.5 shows the expanded FeatureManager for a part with an in-context reference in a sketch.
481
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 482
Working with Assemblies
External references can have four states, which are also shown in Figure 16.5. These are: n In-context n Out-of-context n Locked reference n Broken reference
FIGURE 16.5 The in-context “carrot” on Extrude1 and Sketch1
In-context I have already discussed the in-context relationship earlier in this chapter. Out-of-context Out-of-context means that the document — usually but not necessarily an assembly — where the reference was created is not open at the time. It is indicated by an in-context symbol followed by a question mark. You can open the document where the reference was created through the RMB menu, using the Edit In Context option. Edit In Context opens either the parent part of an inserted part, or the assembly where the reference was created. When you open the referencing document, the out-of-context symbol changes to the in-context symbol. Locked reference You can lock external references so that the model does not change. Other features of the part may be changed, but any external reference within the part remains the way it is until the reference is either unlocked or removed. In our Box-and-Top example mentioned earlier, this means that if the Bottom part is changed, and the external reference on the Top is locked, then the Top will no longer fit the Bottom.
482
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 483
Modeling in Context
One of the best things about locked references is that you can unlock them. They are also flexible and give you control over when updates take place to parts with locked references. Broken reference The broken reference is another source of controversy. Some users believe that if you make incontext references, the best way to respond to them is to break them immediately. However, I would argue that using the Break References function is never a good thing to do. I believe that you should remove the reference by editing the feature or the sketch or change it to make it useful. The problem with a broken reference is that it has absolutely no advantage over a locked reference. For example, while locked references can at least be unlocked, broken references cannot be repaired. The only thing that you can do with a broken reference is to use Display/Delete Relations or to manually edit features to completely remove the external reference. Perhaps it would be better for SolidWorks to replace Break References with a function called Remove References. Would anyone like to make an enhancement request? Best practice is to not put yourself in a situation where you are using either locked or broken references. Parametric relations should not change if the driving geometry does not change. Again, as is typical with CAD software, things may happen that you cannot explain, but there is always a reason for it (even if it is not immediately apparent).
BEST PRACTICE
You cannot selectively lock or break external relations. For example, all of the external relations in the part can be locked, all of the external relations can be broken, or none of them can be locked or broken. If you need to selectively disable relations, then you should consider suppressing features, sketch relations, end conditions, or sketch planes.
List External References You can access the locked and broken references through the List External References option on the RMB menu of any feature with an external reference symbol. Figure 16.6 shows the name and path of the assembly where the external reference was created, as well as the part names and entity types.
FIGURE 16.6 The External References dialog box
483
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 484
Working with Assemblies
No External References The No External References button on the Assembly toolbar is also available through Tools ➪ Options ➪ External References ➪ Do Not Create References External To The Model. As its name suggests, this setting prevents external relations from being created between parts in an assembly. When you offset in-context edges or use Convert Entities, the resulting sketch entities are created without relations of any type. This lack of references includes the InPlace mate, which is not created when a part is created incontext. As a result, when you add the part to the assembly, if you exit and later re-enter Edit Part mode, then SolidWorks reminds you that the part is not fixed in space by displaying the warning shown in Figure 16.7.
FIGURE 16.7 The dialog box that warns you about adding in-context relations to an under-defined part
This message should remind you that in-context features should be used only on parts that are fully positioned in the assembly.
External reference settings in Tools, Options The Tools ➪ Options ➪ External References pane of settings controls many aspects of the behavior of external references. You can find a full description of all of the options in Appendix B; however, I will discuss two of these options in this section. I have discussed one of these references earlier — No External References — and I discuss the other feature, Multiple Contexts, next. This page in the Tools ➪ Options dialog box is shown in Figure 16.8.
FIGURE 16.8 The Tools ➪ Options ➪ External References pane
484
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 485
Modeling in Context
In-context best practice suggestions In-context techniques are most frequently misused by beginning to intermediate users. Many users purchase the software because of the promise of parametric relationships between parts. However, this is a technique that requires a fair amount of discipline, restraint, and judgment. The potential problems associated with overuse or misuse of in-context techniques primarily include performance problems (speed) and lost references due to file management issues. Users may also experience problems with features or sketches that change with each rebuild. The following section contains best practice suggestions that can help you avoid these situations.
Multiple contexts Multiple contexts occur when a part has references that are created in multiple assemblies. By default, multiple contexts are prevented from happening. If you place a part that already has external references into a different assembly, a warning appears, as shown in Figure 16.9.
FIGURE 16.9 The warning message that appears about multiple contexts
Although SolidWorks displays many warnings about multiple contexts, you may still run into situations where you need to use them. For example, you may have a subassembly where a part, such as a top plate of a stand, has in-context references to locate a set of mounting holes. When you place the subassembly into the top-level assembly and mount another assembly to the top plate, another set of in-context holes is required in the top plate. Figure 16.10, at the top, shows the first table and points out the in-context relations. At the bottom, the large bracket appears for the other machine that is mounted to the table top using more in-context relations. In Figure 16.11 are the External References dialog boxes for the two different in-context features. Notice that the Assembly fields at the top of the External References dialog boxes are different. You can only achieve this by activating the Allow Multiple Contexts for Parts When Editing in Assembly option shown in Figure 16.8.
485
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Working with Assemblies
FIGURE 16.10 Using multiple contexts
486
Page 486
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 487
Modeling in Context
FIGURE 16.11 External References dialog boxes
The Tools ➪ Options setting for multiple contexts is a system option. This means that this option is either on or off for every document on a single machine, but when the assembly is used on another machine, the option is off. Rather than always leaving this option on for all documents on a given computer, I think it would be best if it were a document-specific option that traveled with the document, rather than sticking to the machine — another possible enhancement request.
NOTE
The best practice is to avoid creating multiple-context references. If you need to do this, then be very careful about naming files, and remember to turn off the multiple-context option when you have finished creating the reference.
BEST PRACTICE
If you receive a multiple-context part from someone else, the best thing to do is to determine whether you have all of the files required to make it work. RMB click the external reference symbol and select Edit In Context to determine whether SolidWorks can find the right files.
487
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 488
Working with Assemblies
Aside from doing some programming, the only way to find out whether a part was created as a multiple-context part is to examine the External References list for each in-context feature. This can be very time-consuming. Although multiple-context parts should be very rare, it is impossible to determine ahead of time whether or not a part that you have received is a multiple-context part, at least without programming. I once worked on a part that had both some in-context and some out-of-context features. Of course, this looks strange when you realize what you are looking at because in most situations, if any references are out-of-context, all references will be out of context. After some examination, I discovered that there were multiple contexts, which were created because of poor file management. The assembly had changed names slightly, and caused the original in-context relations to not be recognized. I will discuss in-context relations and file naming later in this chapter.
In-context with configurations On the surface, mixing in-context references with configurations sounds like it is combining two powerful techniques that should offer you great control over models. Although this may sometimes be true, I want to caution you about some of the effects that combining these two techniques may cause. In particular, you should be careful about part configurations, particularly configurations of the referenced part. If you are using in-context relations to parts with configurations, then you may want to consider a few things. First, look at the door-hinge part shown in Figure 16.12. At the top are three configurations of one of the hinge plates. The second hinge plate is built in the context of the assembly so that it will always match the first plate. At the bottom are the results of changing the first hingeplate part configuration in the assembly. This looks like an ideal situation because the second hinge plate always changes to match the first hinge plate. What could be wrong with this? The problem here is that you can only show the size of the second hinge plate that corresponds to the configuration of the first plate that is active in the assembly. If you had two instances of the hinge assembly in a top-level assembly, then you would be able to show only one size for the second plate. A second situation where combining in-context references and configurations can cause you trouble is if you have referenced the edges of a part from another part, and a configuration of the referenced part either adds or removes fillets or chamfers, thus breaking the edges. Either of these situations can cause the in-context sketches or other features to fail. This may be a reason to reference the underlying sketches, rather than the model edges or faces themselves. In some situations, configurations work well with in-context relations. One example of this would be when an assembly has many configurations used for positioning parts. Use one configuration for the sole purpose of creating in-context relations.
488
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 489
Modeling in Context
FIGURE 16.12 Combining in-context references with configurations
In-context with motion You should make in-context references between parts where there is no relative motion. The parts themselves can move relative to the rest of the assembly, but they should remain stationary relative to one another. The parts should also be fully defined to ensure that they will not move; you should not simply count on avoiding dragging underdefined parts.
489
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 490
Working with Assemblies
In some cases, such as an assembly of imported parts, it may make sense to fix parts in bulk rather than to mate them. When you are using in-context relations, you need to take extra care to ensure that the parts do not move around. When parts move around, in-context features also move. Obviously, if the motion is around a hole, and the in-context feature is circular and is not affected by the rotation of the referenced part, then it makes less difference; however, if there is a keyway, that may change things. You need to pay attention when combining underdefined parts and incontext features.
BEST PRACTICE
For best practice, you should avoid in-context relations between parts when relative motion is allowed between these parts.
In-context with multiple instances Another situation that can cause problems is when multiple instances of an in-context part are being used in the assembly. In cases like this, you need to be careful and consistent, by always using the same instance to create the in-context relations. You can do this by putting parts into folders, or giving the in-context part a special component color.
In-context and file management Understanding what you are doing with file management is imperative when working with parts that depend on in-context features. Because the references are stored in both the part that is doing the referencing and the assembly where the reference is created, improperly changing the name of either document is bound to cause problems. For example, if you rename an in-context part using Windows Explorer, then the assembly will not recognize the part, as demonstrated in an earlier chapter. This also means that any in-context references will not update.
BEST PRACTICE
For best practice, you should use either the SolidWorks Save As command or SolidWorks Explorer to rename parts and assemblies.
In-context and mates This was mentioned earlier, but a section on in-context best practices would not be complete without issuing the warning against mating to in-context features. Mating parts to in-context features creates a parametric daisy chain, thus establishing an order in which assembly features and mates must be solved. This always creates performance problems in assemblies, especially large ones.
Circular references Circular references in assemblies are a bigger problem than most people realize. In fact, most people do not realize that circular references are a problem, or, for that matter, that they even exist. A circular reference takes the form of “Part A references Part B, which references Part A.” It creates a circular loop that really wrecks assembly rebuild times. Part feature design trees are not susceptible to this sort of looping because the part FeatureManager operates in a linear fashion (at least when it comes to applying relations between sketches or features).
490
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 491
Modeling in Context
The Assembly FeatureManager is solved in this order, or an order that is very similar: 1. Solve reference geometry and sketches that are listed before parts in order, at the top of the design tree. 2. Rebuild individual parts as necessary. 3. Solve the mates and locate the parts. 4. Solve in-context features in parts. 5. Solve reference geometry and sketches listed after the mates. 6. Solve assembly features and component patterns. 7. Loop to step 3 to solve mates that are connected to anything that was solved after the first round on the mates. 8. Continue to loop until complete.
As you can see, even if you do not have a reference such as “Part A references Part B, which references Part A,” it is still possible to get a highly convoluted, if not entirely circular, loop. Many users with smaller assemblies in the hundreds of parts complain about very poor performance. Unfortunately, it is far easier to complain than to really examine what is going on.
Skeletons and layouts When making in-context references, a technique that can help you avoid circular references is to always create references to parts that are higher in the design tree. You can expand on this idea until a single entity is at the top of the design tree, to which all in-context references are made. This could take the form of an Assembly Layout Sketch, or a skeleton. These concepts are discussed in chapters 11, 12, and 13. Remember that the layout sketch consists of a single or even multiple sketches that control the overall layout of the assembly, as well as all of the relationships between parts. When you refer all of the relations to a single entity that does not change with part configurations, or lose or gain filleted edges, the inter-part parametrics become much stronger and more stable. When building a mold for plastic injection molding, a single sketch can control the size and position of the plates, pins, and so on. If all of the 3D parts are mated to the 2D sketch, or use the 2D sketch by converted entities, then the parts will move with the sketch. This same technique is important and useful for any type of die or punch design, along with many other types of design.
In-context and libraries Library parts should never contain in-context references, especially if the in-context references are out-of-context. Small library assemblies may have in-context references between the parts, but a single part should not have features created in-context. External references may be unavoidable in the form of mirrored or base parts, but in-context references are completely avoidable.
491
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 492
Working with Assemblies
Removing relations You can remove relations by using the Display/Delete Relations tool. You can sort the relations by selecting the Defined In Context option, as shown in Figure 16.13.
FIGURE 16.13 Sorting sketch relations by type
If you are considering using the Break Relations tool, then you should either reconsider and use Lock Relations instead, or simply remove all of the in-context relations altogether. Other types of in-context references are not as easy to remove as sketch relations. When you see the External Reference symbol on a sketch, it could be the sketch relations, or it could be the sketch plane that was in-context. In order to fix this problem, you must redefine the plane locally in the part. You can make a local plane from an existing in-context plane (or even just a 3D view) by using the following workaround. Looking normal to the view, open a 3D sketch, and draw three sketch points that do not pick up automatic sketch relations to anything else. Once the points are drawn, select all three of them and make them coincident. Then delete the coincident relation and drag the points apart. The three points come out on a plane that is parallel to the plane of the screen. Next, simply make a three-point plane.
TIP
You should also not forget end conditions such as Up To Surface, Offset From Surface, or even From Surface. If an external reference symbol remains on a feature, you can use the Parent/Child option on the RMB menu to locate it. Remember that using an edge or vertex for a plane definition can cause an in-context relation.
Should you use mating or in-context? You should not become too enthusiastic about in-context relations. This can cause you to do things such as using in-context relations to locate parts, or using in-context instead of mating parts.
492
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 493
Modeling in Context
In-context modeling is like chocolate: a little is a wonderful thing, but too much can be bad for you. You should only use in-context to locate or size features. In-context is initially so fast and easy to use that it can be addictive, but you need to think before you use it.
Communicating design intent If someone else needs to use your model after you are done with it and possibly edit it, then you should leave them some clues to help them understand how the model works, and how it is best changed. For example, you can use descriptive feature and sketch names, comments that are associated with features, the Design Binder to add documentation, and the Design Journal to write notes. You can even put HTML links in notes that display in the graphics window. In-context design intent may not always be obvious, and an impatient user may find it more expedient to delete the in-context references and replace them with either local relations or no relations at all. The more you document your intent, the more likely others will be to follow it.
Other Types of External References The external reference symbol (- >) indicates in-context features that have been created in the context of an assembly, but it also indicates three other types of external references: n Inserted parts n Split parts n Mirrored parts
Inserted parts Inserted parts are discussed to some extent in Chapter 10, and in more detail in Chapter 28. In the past, inserted parts have also been called base parts and derived parts, and some users still use those names. An inserted part is simply an entire part that has been inserted into another part. This is sometimes referred to as a pull operation because the data is pulled from the original part into the child part. The part may be inserted at any point in the history of the design tree, and it may create an additional body within the part or be added to the existing one. Additional features can also be added to the inserted part, but you cannot see or change any of the features of the part that has been added from the downstream document. The inserted part becomes much like an imported, or dumb, solid. Items that can be brought along with the inserted part are solid bodies, surface bodies, planes, and axes. You cannot bring features or sketches. You can use a particular configuration of the inserted part in the child part. I discuss this aspect in Chapter 14, dealing with configurations, and also in Chapter 28.
493
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 494
Working with Assemblies
You can use inserted parts for many modeling applications, such as cast parts and secondary operations. You first insert the original cast part into a new blank part. Then, you add cut and hole features until the part resembles the finished part. Another application for inserted parts is a single part that has been built from several models. For example, I once worked on a large, rather complicated plastic basket, where the basket was modeled as three individual parts, and then reassembled into a single part. Another application may be to insert a part as a body into a mold block to create a mold cavity. To insert a part into another part, you can select Insert, Part.
Split parts I discuss split parts in detail in Chapter 28, in the section about master models. Inserted and split parts are both master model techniques, as are a few more techniques that I discuss in Chapter 28. Some people also include in-context techniques with the master model tools because this is a way of making several parts update together. Split parts are sometimes called a push operation because the data is pushed from the original part to the children parts. The split function takes a single body and splits it into several bodies, optionally saving the bodies out as individual parts. This is done for various reasons, such as creating a single, smooth shape out of several different parts, for example, automobile body panels or the various covers and buttons on a computer mouse. You can use the split parts technique for other applications as well. Sometimes a product is designed as a simple, single solid to keep the modeling simple, and because it is not known how the parts will be assembled or manufactured. When the manufacturing decisions are made, the part can be split into several models that have the engineering details added to them.
Mirror parts You can mirror a right-handed part to create a left-handed part. To activate the Mirror Part command, you must select a plane or planar face. Then, select Insert ➪ Mirror Part to initiate the Mirror Part command. Mirror parts can also use configurations, and so if you have one of those “mirrored exactly except for . . .” parts, you can select the configuration of the parent from the child document.
Tutorial: Working In-Context Follow these steps to get a feel for the workflow of working with parts in the context of an assembly: 1. Open the assembly named Chapter 16 Tutorial Assembly.sldasm. 2. Set the colors that are to be used during in-context editing. Remember that two settings control this — one at Tools ➪ Options ➪ Colors, and the other at Tools ➪ Options ➪ Display/Selection, as shown in Figure 16.14.
494
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 495
Modeling in Context
FIGURE 16.14 Setting in-context colors
Set the Assembly, Edit Part color to a shade of blue, and the Assembly, Non-Edit Parts to a shade of gray. Also set the Assembly Transparency for In Context Edit setting to Force Assembly Transparency, with the slider at around 90 percent.
495
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 496
Working with Assemblies
3. Now you are ready to begin. Select the Table Top part, and click the Edit Component button on the Assembly toolbar. This command is also available through both the RMB menu and the drop-down menu as Edit Part. (If you RMB click a subassembly, the Edit Subassembly option becomes available.) Notice that the Table Top part and the FeatureManager text turn the same color. 4. Expand the Table Top part in the Assembly FeatureManager, select the Front plane, and open a new sketch on it. Notice that you cannot select the edges of the transparent parts through the transparency, even if the Select Through Transparency option is turned on (Tools ➪ Options ➪ Display/Selection). This setting applies only to faces, not to edges. Instead, change the display mode for the entire assembly to Wireframe. 5. Now select the 16 hole edges on the legs. It does not matter whether you select the top edges or the bottom, or even a combination of top and bottom. Use the Convert Entities command to project the edges into the sketch plane as circles, as shown in Figure 16.15.
FIGURE 16.15 Converting entities in-context
6. Create a cut that goes Through All. You may have to change the direction of the extrude to get it to work. Save the tutorial assembly. 7. Now open the file named Chapter 16 Tutorial Machine Assembly.sldasm. Notice that the Table Top part in this assembly is using the Wireframe display state, which is assigned in the Display pane.
496
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 497
Modeling in Context
8. RMB click the part and select Edit Part from the list, or select the part and click the Edit Component button on the toolbar. A warning will display that the part has features that were created in the context of another assembly. You can edit the part, but you cannot add any more external references (in-context features) to it. 9. Toggle off the Edit Component button on the Assembly toolbar to exit Edit Part mode. 10. In Tools ➪ Options ➪ External References, select the Allow Multiple Contexts for Parts When Editing in Assembly option. Now try to edit the Table Top part again in the context of the assembly. This time, no warning message displays. 11. Make sure that you are editing the Table Top part. It will not change colors as specified in the Tools ➪ Options ➪ Colors settings because it is using the Wireframe display mode. Ensure that the status bar in the lower-right corner displays Editing Part rather than Editing Assembly. 12. Open a sketch on the Front plane, and convert the four edges of the holes, as shown in Figure 16.16.
FIGURE 16.16 Creating holes in-context
497
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 498
Working with Assemblies
13. Cut the holes using the Through All setting. Again, be aware of the direction of the cuts. Toggle out of Edit Component mode and press Ctrl+S to save the assembly. Figure 16.17 shows the finished assembly.
FIGURE 16.17 The assembly as of step 13
14. Open the Machine Base Bracket part in its own window by selecting Open Part from the RMB menu. The part is shown in Figure 16.18.
498
23_080139 ch16.qxp
3/26/07
3:59 PM
Page 499
Modeling in Context
FIGURE 16.18 The Machine Base Bracket part, ready for mirroring
15. Select the Front plane and select Insert ➪ Mirror Part. This creates a new part and opens a new PropertyManager interface, as shown in Figure 16.19.
FIGURE 16.19 The Mirror Part PropertyManager
In this case, you do not need to add any of the items in the list, and so you can deselect any that are selected and click OK.
499
16
23_080139 ch16.qxp
Part III
3/26/07
3:59 PM
Page 500
Working with Assemblies
Figure 16.19 shows the Locate Part panel of the Mirror Part PropertyManager. This panel does not appear when the feature is first created, although it probably should. This screen capture was taken with SolidWorks 2007 sp1.1, 32-bit version.
NOTE
You can use Locate Part to move the part once it is inserted. If you do not use it, then the part is just positioned using its mirror plane. For this reason, it is best practice to mirror about one of the standard planes. Also note that the template used for this part was chosen based on the settings at Tools ➪ Options ➪ Default Templates ➪ Always Use These Default Document Templates or Prompt User To Select Document Template.
16. Notice that the new part is indeed a mirrored copy of the original. You can see that the “MADE IN USA” text on the bottom is backwards. Fortunately, a configuration exists specifically for this purpose. Change the configuration by selecting For Mirroring in the Configuration Name drop-down list in the External References dialog box, as shown in Figure 16.20. Notice that this configuration removes the extruded text from the model.
FIGURE 16.20 Selecting a configuration
17. Add your own “MADE IN . . .” extruded text to the bottom of the part. Save the part.
Summary Although in-context functions are powerful and seductive, you should use them sparingly. In particular, be careful about file management issues such as renaming parts and assemblies. The best approach is to use SolidWorks Explorer or the Save As command with both the parts and assemblies open. Other external references include inserted parts, split parts, and mirror parts. These types of external references are often used in discussions on master models, which I address in a later chapter.
500
24_080139 pt04.qxp
3/26/07
4:00 PM
Page 501
Creating and Using Libraries IN THIS PART Chapter 17 Using Hole Wizard and Toolbox Chapter 18 Working with Library Features Chapter 19 Using Smart Components
24_080139 pt04.qxp
3/26/07
4:00 PM
Page 502
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 503
Using Hole Wizard and Toolbox
T
he Hole Wizard and Toolbox are two applications that go together because of the information they share; they both work from a single database of matching hole and screw sizes. One of the most useful examples of combining these two applications is the ability to automatically place holes through multiple parts and put appropriately sized screws and hardware into the holes, all in one step. The hole knows which fastener or stack of fasteners needs to go together.
Using the Hole Wizard The Hole Wizard enables you to place holes for many types of screws with normal, loose, or tight fits. You can create Hole Wizard holes as assembly features in an assembly or as features in individual parts that are built in the context of an assembly using the Series Hole functionality. This tool is called a wizard because it guides you through the process step by step. The process of creating a Hole Wizard hole can be summarized as follows: n Pre-select the face to put the holes on, although this is not required. This turns out to be an important issue that is related to the type of placement sketch, and I revisit this subject later. n Select the type of hole, for example, counterbored, countersunk, drilled hole, tapped hole, pipe tap, or legacy. n Set the standard to be used, such as ANSI inch, ANSI metric, or ISO. n Select the type of screw. For example, a counterbored hole can accommodate a socket head cap screw or a hex head screw, among others.
503
IN THIS CHAPTER Using the Hole Wizard Understanding Toolbox Tutorial: Gaining experience with the Hole Wizard and Toolbox
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 504
Creating and Using Libraries
n Select the size of the screw. n Select the fit of the screw into the hole, such as normal, loose, or tight. n Select the end condition of the hole. n Select options for clearance and countersinks or edge breaks. n Alternatively, you can use or assign a Favorite. A favorite is a hole with settings that you use frequently and want to save. These are discussed later in this chapter. n You can use Custom Sizing when you need a hole with non-standard dimensions. n Locate the center of the hole or holes. You can place multiple holes in a single Hole Wizard feature, even on different faces and curved faces. I address the specifics of this step later in this chapter. n Click OK to accept the type, size, and placement of the hole. The Hole Wizard PropertyManager interface is shown in Figure 17.1.
FIGURE 17.1 The Hole Wizard PropertyManager Interface
504
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 505
Using Hole Wizard and Toolbox
Anatomy of a Hole Wizard hole Hole Wizard holes are made of two sketches: a center placement sketch and a revolved cut profile. Figure 17.2 shows a simple part with an expanded Hole Wizard feature. Notice that the feature is named for the size and type of the hole.
FIGURE 17.2 A design tree containing a Hole Wizard hole
NOTE
Another useful aspect of naming the hole feature is that if you change the type or size through the Hole Wizard interface, the name changes to match.
If you create a Hole Wizard feature with more than one hole, there is still just a single revolved sketch. A multiple-hole Hole Wizard feature works similar to making a revolved cut and using a Sketch Driven feature pattern to create the multiple instances.
Placement sketch The placement sketch is listed first under the Hole Wizard feature. It has one or more sketch points marking the hole centers. It may also contain construction geometry with relations and dimensions to fully locate the hole centers. Placement sketches are discussed in more detail in the next section, 2D versus 3D placement sketches.
Hole sketch The revolve profile sketch is not on an identifiable sketch plane that you can reuse for other features, although that would be useful. You can change the sketch dimension outside of the wizard interface, and if you later use the wizard to edit it, then the changes appear in the Custom Sizing panel. Figure 17.3 shows the Custom Sizing panel with the changed counterbore diameter highlighted. If you select any of the choices from the Options panel, then the revolved sketch profile is altered to accommodate the change. For example, the sketch changes to add a line for the countersink; a separate chamfer feature is not added.
505
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 506
Creating and Using Libraries
FIGURE 17.3 The Custom Sizing panel
2D versus 3D placement sketches Possibly one of the most difficult aspects of the Hole Wizard for new users to grasp is the use of 2D and 3D sketches to place the centers of the holes. There is a condition that is not immediately obvious, which is that if you preselect a flat face, then the placement sketch is 2D, and if you do not pre-select a flat face (meaning that if you just start the Hole Wizard without having selected a flat face), then the placement sketch is 3D.
Advantages and limitations of the 2D sketch The main advantages of the 2D sketch method are the simplicity and completeness of the available tools. Everyone knows how to manage 2D sketches, sketch planes, dimensions, and construction geometry. I have argued for years that the 2D placement sketch should be the default sketch used, because of its universal nature. A limitation of the 2D sketch is that the holes that you create through this method are limited to a single planar face. Sometimes this creates a great limitation, while other times it does not matter.
Advantages and limitations of the 3D sketch The obvious advantage of the 3D placement sketch is that it can put a set of holes on any set of solid faces, regardless of whether they are non-parallel or even non-planar. This function offers multiple holes, multiple faces, and multiple directions. In situations where that is what you need, then nothing else will do. A limitation of the 3D sketch is that if you have never used 3D sketches, they can be fairly cumbersome. Also, several relation types that are familiar in 2D sketches are not available in 3D sketches. Dimensions work very differently in 3D sketches compared to 2D sketches. For example, to create and place a hole in a specific position on a cylinder, you need to follow these steps: 1. Begin with a circle with a diameter of one inch, drawn on the Top plane, and extruded using the Mid-plane option one inch. 2. Start the Hole Wizard without any preselection, either through the Features toolbar or by selecting Insert ➪ Features ➪ Hole ➪ Wizard.
506
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 507
Using Hole Wizard and Toolbox
3. Set the interface to use an ANSI inch, one-quarter-inch, counterbored hole for a socket head cap screw. Use Through All for the End Condition, and a Normal fit, with a .100inch head clearance (in the Options panel), and no custom sizing changes. These settings are shown in Figure 17.4.
FIGURE 17.4 The Hole Wizard settings for the socket head cap screw
4. Click the Positions tab, which is located at the top of the PropertyManager window. The interface automatically changes to a 3D sketch with the Point tool turned on. This means that wherever you click, you create a point.
507
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 508
Creating and Using Libraries
Be careful about clicking when the Point tool is turned on. For example, if you click in a blank space, then the Point tool places a point off the part. SolidWorks will try to use the point later to create a hole in empty space, which usually causes an error.
NOTE
5. Click the cylindrical surface of the part. The surface appears red when you move the cursor over it to indicate that an OnSurface sketch relation will be created between the sketch point and the cylindrical surface. 6. The hole should be positioned from one end of the cylinder. Using the SmartDimension tool, click one flat end face of the cylinder and the sketch point. Place the dimension and give it a value of .300 inches, as shown in Figure 17.5.
Locating the point angularly around the cylinder is more difficult. You can use several methods to do this, but this example shows one using construction sketch geometry.
FIGURE 17.5 Dimensioning the 3D Placement sketch point
To force a 3D dimension to have a certain orientation, dimension from a plane or planar face rather than from an edge, vertex, or sketch entity. A dimension from a plane is always measured in a direction perpendicular to the plane, but a dimension from a line or point is always measured by the shortest distance between the entities. Two-dimensional sketches can force dimensions to be horizontal or vertical, but 3D sketches cannot.
TIP
3D sketches have the ability to make planes within the sketch, without leaving the sketch environment. Planes that are made in this way cannot be referenced from outside the sketch, are not created using the same methods as regular planes, and do not follow documented techniques reliably. They have been removed from the SolidWorks Corporation training manual examples, and for this reason, I recommend finding other more reliable methods to do the same things.
CAUTION
508
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 509
Using Hole Wizard and Toolbox
7. With the Line tool activated while still in the 3D sketch, Ctrl-click the flat end face that the previous dimension referenced. This moves the red “space handle” origin to the selected face, and constrains any new sketch entities to that face. You are still in the 3D sketch, but are constrained to the selected plane, and still must play by all of the 3D sketch rules. The elements of 3D sketches are described in detail in Chapter 31. 8. Turn on the Temporary Axes view by selecting View ➪ Temporary Axes. 9. Place the cursor near the center of the activated end face; a small, black circle appears, indicating that the end point of the line will pick up a coincident relation to the temporary axis. Draw the line so that it picks up an AlongX sketch relation. The cursor shows the relations about to be applied, just like in a 2D sketch. 10. Draw a second line again from the center, but this time do not pick up any automatic relations. This line should also be on the flat end face.
NOTE
Although you can set these lines to display as construction lines if you like, this is not required in order for the feature to work; they also work as regular solid lines.
11. Put an angle dimension between the lines, and change the angle to 30 degrees. To be thorough (which is always recommended in 3D sketches, which have a tendency to handle underconstrained sketch geometry unpredictably), constrain the ends of the lines to the circular edge of the cylinder. At this point, the part looks like Figure 17.6.
FIGURE 17.6 The example part at the end of step 12
509
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 510
Creating and Using Libraries
12. Create an AlongY sketch relation between the points indicated in Figure 17.7. The hole centerpoint on the cylindrical face is one of the points, as well as the endpoint of the angled line. Change the angle dimension to ensure that it is controlling the sketch point as expected.
FIGURE 17.7 Control the placement of the 3D sketch point around the cylinder.
The finished part from this example is on the CD-ROM, and is called Chapter 17 3D Hole Placement.sldprt.
Making and using Favorites Hole Wizard Favorites store types of holes that you use frequently so that you can simply recall a favorite, rather than manually making all of the changes every time you use the same hole. Favorites are saved to a database named Default.mdb as you create them, and are immediately available from all other part documents. You can also save favorites to a special file type, with the extension *.sldhwfvt. You can then load these files and add them to other Default.mdb databases.
510
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 511
Using Hole Wizard and Toolbox
Creating a Hole Wizard Favorite To create a Hole Wizard Favorite, set up a Hole Wizard hole as you normally would, and then use the Add Favorite button to add it to the Favorites database. The Hole Wizard Favorite panel contains five buttons: Apply Defaults/No Favorites: Removes favorite settings from the current interface, setting all values back to their defaults. Add or Update Favorites: You can use this button to either add a new favorite to the database or change the name or other settings for an existing favorite. Delete Favorite: Removes a favorite from the database. Save Favorite: Saves a favorite to an external file with the extension, *.sldhwfvt, which can be loaded by other users and added to their databases. Load Favorite: Loads a saved favorite file.
Storing custom holes You can use Hole Wizard Favorites to store custom holes. Create the hole with its custom sizes, and then add the favorite and give it a recognizable name. The custom hole will now be available to anyone who connects to the same database file.
Administering Hole Wizard Favorites The database file is typically found in the Data subdirectory of the SolidWorks installation directory, but an option in Tools ➪ Options ➪ File Locations theoretically enables you to move the file to somewhere else. Further, the *.sldhwfvt files do not have an entry in the File Locations list, but seem to always default to the lang\english subdirectory of the SolidWorks installation directory. Neither this location nor the Data directory makes sharing among multiple users very convenient, but both file types can be copied to other installations. It is a best practice to create a folder for library type files that you want to save and use with a future version of SolidWorks. You can specify the locations for these files through Tools, Options, File Locations. I recommend a location such as D:\Library. This moves the file off of the same drive as the operating system, in case you need to reformat, and it keeps it out of the Program Files area to prevent it from being lost or overwritten when SolidWorks is installed, uninstalled, upgraded, or changed in other ways. Even for files that need to remain in the SolidWorks installation directory (such as macros) it is best to also have these backed up in a library location.
BEST PRACTICE
Favorites quirks Hole Wizard Favorites seem to have a couple of quirks that are possibly “sub-optimal,” as they say. First, you can only see the favorites for a specific type of hole when that type of hole is activated in the interface. For example, if you have a number of favorites for countersunk holes, but you currently have the counterbored hole icon activated, then you will not be able to see the countersunk favorites until you switch to the countersunk icon.
511
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 512
Creating and Using Libraries
If you have a lot of favorites, then this may be beneficial, but if you have only a few favorites, or you do not use favorites frequently, then it may be confusing, and can create some unnecessary steps to find all of your favorites. A second quirk occurs when you allow SolidWorks to name the favorites and you have fractional values such as 1⁄4 — which happens now and then in hole sizes — and then try to save the favorites. Each favorite is saved as a separate file, using the name that was automatically assigned to it by SolidWorks as the filename. Unfortunately, the character “/” is not allowed in a filename, and so it fails. Fortunately, you can change favorites names by using the Add Or Update Favorites button on the Favorites panel of the Hole Wizard PropertyManager. When saving Hole Wizard Favorites, SolidWorks has no way to establish a default folder for these files, although it seems to always go to the lang\english subdirectory of the SolidWorks installation directory. You need to determine a folder to put them into and load them from, and browse to that location every time, especially if you are using a shared network. Also, remember to copy any favorites files to a backup library location.
Using the Hole Series The Hole Series enables you to make a series of in-context hole features in individual parts that are connected by a Hole Series assembly-level feature. It is intended for a stack of parts where, for example, the top part has a counterbored hole, the middle part has a clearance through hole, and the final part has a blind threaded hole. You can also do this by using an existing hole to align the rest of the series.
Hole Series interface The Hole Series used to be part of the Hole Wizard, but has since been exported as a separate tool. It is now a four-step, wizard-based feature. Figure 17.8 shows the interface for the various steps. Notice in the first panel that there is an option to add a Smart Fastener. The Toolbox feature, which I discuss in the next section, is required to be able to add Smart Fasteners.
Basic Hole Series steps When using the Hole Series feature, you must follow these basic steps: 1. Have an assembly open with two or more parts in it that need to be fastened together. 2. Initiate the Hole Series tool by selecting Insert ➪ Assembly Features ➪ Hole ➪ Hole Series. It is also available as a toolbar button, but it is not on the toolbar by default. The Hole Series also depends on pre-selection to decide whether it uses a 2D or 3D sketch for the placement sketch. You should always pre-select a flat face before creating a Hole Series feature. 3. If the Hole Series is to be started from an existing hole, then select it in the Hole Position panel. If not, then use sketch points, construction geometry, dimensions, and sketch relations to locate the hole centerpoints.
512
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 513
Using Hole Wizard and Toolbox
FIGURE 17.8 The Hole Series interface
513
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 514
Creating and Using Libraries
4. Use the blue arrow at the top of the PropertyManager to advance from one panel to the next.
n The Start Hole Specification is referring to the part where the series of holes starts. n The Middle Hole Specification is for all parts between the first part and the last part. n The End Hole Specification is the last part and is either a through clearance hole or a threaded hole. The finished feature leaves an in-context feature in each part, with the Hole Series part in the assembly, as shown in Figure 17.9.
FIGURE 17.9 The finished Hole Series
514
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 515
Using Hole Wizard and Toolbox
Comprehending Toolbox I recommend that you read this section through, from beginning to end. If you read a paragraph out of context, then you may not understand the point that I am making. With Toolbox, it is vital that you know what you are doing, to ensure the quality of your production data regarding fasteners and hardware.
CAUTION
Improper installation, maintenance, or management of Toolbox can cause the loss of all useful information about fasteners and hardware in your assemblies.
Toolbox is an add-in that requires SolidWorks Office or higher, although you can also purchase it separately. In this book, I typically avoid talking about add-ins because the amount of material simply becomes overwhelming at a certain point; however, Toolbox is the cause of much consternation among users and CAD Administrators, and so it deserves some attention. Toolbox is an application that creates fasteners and other hardware components, on the fly or reuses existing parts when possible. Technically, Toolbox is not a library, but a configurator. Libraries store existing components, while configurators build them on the fly from information supplied by the user. One advantage of configurators is that the parts start out very compact because there is only the default size, and the sizes are efficiently stored in a database, and created as needed. The advantage of a library is that it allows you to simply plug in the parts and they work. No mess, no fuss. This is not how Toolbox works, but it is good to remember the fact that what Toolbox really needs to do for users is provide a library of parts. Anything more than that is only beneficial if it offers some improvement over a simple library of existing parts without introducing any risks or setbacks.
How Toolbox works Because Toolbox is not a library, and is not passive the way a library is, there is a component of it that is active. To make an analogy, no one asks how a staircase works, because it does not work, it simply exists, and people use it. An escalator, however, is a different issue. With an escalator, there is a complex installation, and then to operate it, you have to know how to get on and get off, and what to do if it stops working. The end results of using the staircase and using the escalator are the same (you start at the bottom and arrive at the top), but the complex automation is supposed to save you some effort. That is one of the ways in which you can look at Toolbox. The end product is supposed to be the same as using a static library of parts, but there is some mechanism behind the scenes that has to be set up and maintained properly in order for it to work in the way you expect. Most SolidWorks books, tutorials, or training materials are going to ask you to accept what happens inside Toolbox as a “black box” and just assume that the end results are exactly what you need and intend. Here, I supply you with information about how it works, because it is important.
515
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 516
Creating and Using Libraries
The database When Toolbox is installed, it starts as a set of SolidWorks parts with named features and dimensions, some suppressed features (depending on settings), some dlls (executable programs), and a database. The parts have a single Default configuration, which is typically one of the size extremities, either the largest or smallest. The database starts out about 65MB, and includes all of the size information for all of the parts, as well as all of the standards information. If you create a custom standard in Toolbox, it actually replicates a section of the database. By doing this, the database file can easily double in size. Later, you will see that a network installation of Toolbox requires the database to be on the network, and every time you create a new fastener, it has to open the database. As a result, simply placing a screw in an assembly can mean that even if your assembly is located on your local hard drive, you still have to open a very large database file across the network. The first rule about performance with SolidWorks is to work locally rather than across a network. By default, the database is located at C:\Program Files\Common Files\SolidWorks Data\Browser\ lang\English\SWBrowser.mdb. You can open this file with Microsoft Access or Excel. When specifying network paths, it is best to specify a universal naming convention, or UNC, path rather than a mapped address. A UNC address follows the format, \\Server\Shared Folder. The advantage of the UNC over the mapped drive is that mapped drives do not always connect immediately, but the UNC should be able to find its link as long as the network is working. Also, mapped drives can vary from one computer to another, but the UNC is always the same.
NOTE
The Configurator application If you have just installed Toolbox the way that most, if not all, new users do, then you will accept all defaults, and trust the software that you just purchased to not give you bad advice. In this situation, the database is installed locally and Toolbox is set to use configurations for sizes. When you put a Toolbox part into an assembly, you do not even notice anything other than the part going into the assembly, although it may hesitate while the large database is opened. If you check the part configurations, you may notice that there is a Default config and a new one that represents the size that you just created. Every new size that you create makes another new configuration. Figure 17.10 shows a Toolbox part with the FeatureManager and ConfigurationManager open. Next, you may receive an assembly from a client. Often, because Toolbox parts are located in an area where you would not necessarily look for parts, users send assemblies and parts, but do not send Toolbox parts. You may think that this is okay; after all, you have Toolbox on your system, and so it should pick up your toolbox parts. The truth is that when receiving an assembly from someone else, you are better off if one of the parties does not have Toolbox on their system. Here’s why:
516
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 517
Using Hole Wizard and Toolbox
FIGURE 17.10 A Toolbox part showing the FeatureManager and ConfigurationManager
Huge screws If both you and the client who sent the assembly have Toolbox, then you should be okay, right? Well, yes and no. Yes, your client’s assembly will pick up your Toolbox parts, but no, it will not work properly because you do not have all of the same configurations and sizes that your client has. In cases like this, you will experience what I have come to refer to as the Huge Screws syndrome. When SolidWorks finds the right file but cannot find the right configuration, it uses another configuration, usually the Default, which is generally the biggest size. This is where the Huge Screws name came from. Part of the really bad news is that if you save your assembly with the Huge Screws, SolidWorks has no way of knowing that the huge screws are not the correct screws, and the problem can be solved only by manually going through the assembly and reassigning sizes to the huge screws. You can work around this by opening an assembly that has not yet been saved with the Huge Screws, by using the Advanced option in the Open dialog box, and selecting the New Configuration Showing Assembly Structure Only option. With this option, all components are suppressed. You can unsuppress any non-Toolbox parts and continue working. Ask your client to send you his Toolbox parts and then unsuppress those parts in the assembly, making sure that it finds the right parts, which is probably best done by having the correct parts already open before you open the assembly. These options are shown in Figure 17.11.
517
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 518
Creating and Using Libraries
FIGURE 17.11 Opening an assembly with all parts suppressed
If you replace your Toolbox parts with the Toolbox parts from the client, then you may experience the same problem in reverse if you had configs that your client did not. In the end, it would be great to be able to merge the two parts to combine all of the available sizes into a single file. There is a way of doing that, which I will describe later. Files that have the same names and different content are at the top of the list of things you shouldn’t do in file management, and yet the SolidWorks Toolbox system frequently creates this very situation.
A slight retraction To be fair, SolidWorks has fixed the Huge Screws problem in the 2007 version, by coming up with a clever method for figuring out which size is missing and building it on the fly when the assembly is opened. Additional information about the Toolbox parts is now stored in the assembly, which helps identify the missing parts. Unfortunately, the fix only works for assemblies that use the parts from the new 2007 library and assemblies that have been built in SolidWorks 2007. To sum up, if you have assemblies built in an older version of SolidWorks, and your Toolbox library becomes corrupted or lost, or you are sent an assembly that uses a different Toolbox library, even if you are working in SolidWorks 2007, you cannot benefit from this fix.
518
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 519
Using Hole Wizard and Toolbox
This is disappointing in many respects because anyone who has existing Huge Screws problems will continue to have them until they rebuild the assembly or manually repair the configurations. It is doubly disappointing because the information needed to recreate the correct configuration has always been stored in the assembly — the filename and the configuration name are enough — but SolidWorks has missed an opportunity to really fix this problem. Before the Summary at the end of this chapter, I have some recommendations if you are still interested in using Toolbox.
Toolbox organization Toolbox parts can be organized in a number of ways. The raw parts are organized as follows: n Standard and Units (for example, ANSI Inch or ANSI Metric; most standards do not include multiple units, they assume metric). n Hardware Type (such as bearings, bolts, and bushings). n Each type is organized differently, but bolts and screws are organized by drive or head type (for example, you have socket head screws, hex head, and thumb screws). n Filenames look like Socket Button Head Cap Screw_AI.SLDPRT, where the “AI” represents ANSI Inch. Figure 17.12 shows this organization in part.
FIGURE 17.12 Toolbox content organization
519
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 520
Creating and Using Libraries
Configurations or parts? By now you are probably unsure about the use of configurations in general. If so, that is not the impression I am trying to convey. Configurations in themselves are not the problem; the problem here is in the file management practice of having files with the same names but different content. Mixing that with the practice of trying to treat “configurator” software like a “library” exacerbates the problem. That said, you have two options regarding how you create different sizes. The default option is that sizes are created as configurations within a single part. The other option is that sizes are created as individual files. The best time to make this choice is before you install SolidWorks. Unfortunately, before you install SolidWorks, you probably do not have any idea that these issues exist. The reason for making this decision not just early, but immediately, is that if you start using the default setting (configurations), and make a few configurations for some parts, and then switch to using the Save Parts setting, the parts that are saved out will all have the pre-existing configurations, and thus different sizes. If you find yourself in this situation, it is better to reinstall Toolbox, or simply to copy over a new default library with no configurations. You can access the option to either Create Configurations or Create Parts by selecting Toolbox ➪ Configure ➪ Settings, as shown in Figure 17.13. I will discuss the other settings in this dialog box later in this chapter.
Which is better? The following list contains some pros and cons of each option. Configurations are better for: n Controlling data across several sizes. For example, a design table can drive custom properties that are added to all configurations. Doing this with many individual parts would be very messy. n The interface to select configurations from a list is easier to work with than the interface to select a part from a list. n File management organization is somewhat easier for configured parts. Separate parts are better for: n Keeping the file size small. n Replacing all of one size part with another. n A guarantee that you will never have the Huge Screws problem.
520
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 521
Using Hole Wizard and Toolbox
FIGURE 17.13 Toolbox settings for the Create Configurations or Create Parts options
Materials or custom part numbers in Toolbox Maybe your company uses screws of different materials or finishes in your products. Toolbox, in its default arrangement, does not have an option to deal with this directly. If you ask a tech support person whether materials and custom part numbers can be used in SolidWorks, they will tell you “of course, simply enter in the desired quantity when making the part.” The implication here is that you do them one at a time, and that whoever creates the part uses the same syntax as everyone else. Figure 17.14 shows the PropertyManager interface for adding a Toolbox part to an assembly. You can access this interface by dragging a Toolbox part from the Design Library window into the assembly graphics window. The materials assignment is usually intended to be done as part of the Description. You can access this interface and the Part Number fields through the Add Favorite button in the upper-left corner of the Favorites panel.
521
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 522
Creating and Using Libraries
FIGURE 17.14 Adding a part number and description to a new Toolbox part
The way that SolidWorks expects you to work with materials and custom part numbers is simply not practical unless you have one person doing all of the work, and you do not have many parts to create. SolidWorks does not provide any direct way to mass-populate data of this type. One method to work around the lack of a mass-population tool is to first create all of the sizes for a part using configurations. Then auto-create a design table and you can use Excel techniques to build descriptions, custom part numbers, materials, and whatever custom property you want to have. Another method to do this is to create a custom standard for materials. A custom standard essentially copies a high level in the database such as ANSI Inch. You can specify a name such as Company X Stainless Hardware, or Company X Black Oxide Hardware. I have already mentioned that adding custom standards greatly increases the size of the database, and contributes to the delay in adding the Toolbox parts to an assembly. If this is not a handicap for you — and you should at least try it — then it may be a more viable way to incorporate materials and finishes.
522
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 523
Using Hole Wizard and Toolbox
Toolbox in a multi-user environment There are a few ways in which you can make Toolbox work the way it is intended to. The most reliable way is to remove your computer from the network, and to not bring in any assemblies from external sources that were created referencing Toolbox parts. That sounds like an extreme measure, but it is necessary, as Toolbox’s weaknesses come from sharing Toolbox data. Unfortunately, most SolidWorks users do not have this luxury. They generally share files with other users across a network, in a PDM system, or across the Internet through FTP, e-mail, or VPN. If each user has their own Toolbox installation locally, as happens with the default installation, then you could run into the same problems as described above when receiving an outside client’s files. As a result, you must somehow share Toolbox.
Sharing Toolbox Keep thinking to yourself “Toolbox is just a library, Toolbox is just a library . . .” You can share Toolbox by redirecting the Common Files part of the SolidWorks installation to a shared network location. This part of the installation is shown in Figure 17.15.
FIGURE 17.15 Locating the Toolbox library during installation
Sharing an existing Toolbox library This is fine for the first installation, but for any installation where a version of the software already exists on your computer, the shared files also already exist. There is no installation option to accommodate this situation, and so you have to either install over the shared documents or install
523
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 524
Creating and Using Libraries
to a dummy location and redirect SolidWorks to the shared files manually. You have to go through this installation, even the dummy installation, because it is installing the application part of Toolbox. Remember that a Toolbox installation has three components: the empty default library part files, the database with all of the information in it that is used to populate the library, and the application dlls that make everything work. This is particularly important to pay attention to if the library has been changed. If you overwrite the database, that is not really important unless, for example, standards have been changed, or custom properties added. However, if the library has been changed (for example, by adding configurations) and a later installation overwrites it, then you can cause yourself or someone else a lot of difficulties. For this reason, you need to know how to manually redirect Toolbox to a different location. A file called Toolbox.ini is located in the Toolbox subdirectory of the SolidWorks installation directory, as shown in Figure 17.16.
FIGURE 17.16 Finding the Toolbox.ini file
When you edit this file with a text editor such as Notepad, the file contains the path of the SolidWorks Data folder. The database that controls both Toolbox and the Hole Wizard is located in the \lang\English (or appropriate language) folder, and is called SWBrowser.mdb. The Toolbox library parts are in the \browser folder, under the appropriate folders, as displayed in the Design Library. Figure 17.17 shows the Toolbox.ini file open in Notepad.
524
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 525
Using Hole Wizard and Toolbox
FIGURE 17.17 The Toolbox.ini file displayed in Notepad
Toolbox administration If you have only one user, you can do what you like — even use the default installation — and Toolbox should work for you. If, however, you are administering an installation with more than one user, you need to be informed of the issues involving setting up and using Toolbox mentioned above, and a few more mentioned below.
Read-only setting If a Toolbox is shared, is it possible that multiple people can access the same files at the same time? This is one of the most frequently asked questions about Toolbox administration. If two people need to write to a file at the same time, then that can cause problems. In order to remedy this, SolidWorks plays referee between multiple users who are accessing the same Toolbox files. You need to apply the following settings to share Toolbox files on a network: n Toolbox ➪ Configure ➪ Settings ➪ Always Change Read-only Status of Document Before Writing; this option should be on. n The Windows users should have full permissions to access the SolidWorks Data directory, and the SolidWorks Data\Browser directory should be set to Read-only for all users.
Upgrading SolidWorks with Toolbox It is time to upgrade. You have your SolidWorks 2007 disks, and SolidWorks 2006 is installed. You can now go ahead and install SolidWorks 2007, but when it comes to the part in the installation shown in Figure 17.15, take notice again of what you are doing. The installation may default to the SolidWorks 2006 Toolbox location. If you overwrite this location, then you will not be able to use Toolbox with SolidWorks 2006 (because the library will be a future version). If you intend to use multiple versions, then you also need to maintain multiple Toolbox installations. You should also consider what would happen if you make a mistake and completely overwrite the SolidWorks 2006 library that contains all of the configuration data that you have worked hard to create. When upgrading, you do not want to overwrite your existing library. The following is a set of steps to help you upgrade safely and effectively:
525
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 526
Creating and Using Libraries
n Install the new version with Toolbox in a new location, for example SolidWorks 2007 Data or a directory name that helps to distinguish this library from another. n Copy the old SolidWorks 2006 data (containing the correct configurations) over the top of the new SolidWorks 2007 data. n Browse to the Toolbox\data utilities subdirectory of the SolidWorks installation directory and run UpdateBrowserData.exe. The interface for this program is shown in Figure 17.18.
FIGURE 17.18 The UpdateBrowserData.exe interface
n Select the Updating Database field and use the ellipsis button to browse to Toolbox\data utilities\lang\English\updatedb.mdb in the SolidWorks installation directory. n Select the Database To Update field and browse to SWBrowser.mdb. You can find this file by following the ToolboxPartFolder path in the Toolbox.ini file, and looking in the \lang\english subdirectory. n Click Update. This prevents you from overwriting your old version, while still copying the old version to the new installation and avoiding the Huge Screws syndrome.
Adding custom Toolbox parts If you have been using SolidWorks and Toolbox for a few releases, then you may recall that Toolbox had a function called the Add My Parts Wizard, which added user-created parts to the Toolbox libraries. The parts were limited in that you could not use them with Smart Fasteners, but the interface would work if the part had configurations. In SolidWorks 2007, the Add My Parts Wizard has been removed. However, you can still add your own parts to Toolbox by simply dragging-and-dropping them. Drag-and-drop is available in thirdlevel folders. Levels are counted from the Standard folder, which is level 1.
526
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 527
Using Hole Wizard and Toolbox
Adding folders to Toolbox You can add folders to Toolbox through the RMB menu. Just RMB click a first- or second-level folder, and select New Folder. You can create a new level-1 folder by RMB clicking the Toolbox icon, as shown in Figure 17.19.
FIGURE 17.19 Adding a new folder
Merging Toolbox libraries You can merge Toolbox libraries by simply copying or moving one folder in with the existing library folders. Another type of merging may be less successful. If you have two Toolbox parts from different sources and they have different sets of size configurations, these are things you may want to merge to get the benefits of both sets of sizes. Unfortunately, there is no direct way of doing this in Toolbox. The best way would be to autocreate design tables in both parts, and then to copy the configurations from one design table to the other design table. This should effectively copy configurations between parts, although you may need to remove any duplicate configuration rows.
Toolbox and PDM This topic could be a chapter on its own, but I will not delve too deeply into it here because it goes beyond the intended scope of this book. A discussion of Toolbox requires some mention of how it may be used in conjunction with a PDM product. Toolbox and PDMWorks Workgroup, or any other PDM product for that matter, can be a challenge to combine. Generally, it is useful to be able to see the fasteners in PDM because of the BOM capabilities, quantities, Where Used options, and complete searches. Some users choose not to put library parts in the vault because they are not revision-managed documents. All the same, revision management is not the only reason to put items in the vault.
527
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 528
Creating and Using Libraries
Looking at it from the Toolbox point of view, Toolbox cannot work with its parts in the vault, and if changes were allowed to the parts (sizes add configurations), then you would need to check in the part every time you added a size. This is not necessarily a problem, but it does become awkward. Some PDM products allow files to exist outside the vault, while pointers to the files exist within the vault. This is one very good option for using Toolbox with a PDM product. Another good option is to simply use the Create Parts setting. This creates individual files that are easier to manage. It may also be important for a different reason: some PDM products, such as PDMWorks Workgroup, do not distinguish configurations as separate controllable or separately identifiable documents.
Toolbox settings You can find Toolbox settings in the Toolbox menu, by selecting the Configure option. The Configure Data dialog box has four tabs: Content, Settings, Properties, and Smart Fasteners.
Content tab The Content tab shows all of the standards. If you are not using certain standards, then you can turn them off by deselecting their check mark. You can do the same for folders and even specific parts within the standard. If you have added folders or custom parts in the Design Library window, they appear here. As you expand the standard, and then the fastener type and the specific head types, you can select individual parts. The Countersunk Bolt is selected in the list shown in Figure 17.20.
FIGURE 17.20 The Toolbox Configure Data Content tab
528
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 529
Using Hole Wizard and Toolbox
Several tabs contain different types of information for Toolbox parts: n You can use the General tab to offer alternate filenames. n You can use the Size tab to disable specific sizes. n The Finish tab is not available for all fasteners, but you can use it to remove parts of the description. n You can use the Length tab to limit the available lengths. n You can use the Thread Display tab to limit the available thread types. Available thread types are shown in Figure 17.21.
FIGURE 17.21 Available thread display options
Schematic
Simplified
Cosmetic
n The All Configurations tab enables you to create all of the configurations that are available for a particular Toolbox part. It will also export the database data to an Excel spreadsheet, and import a spreadsheet that is created in this way. Creating all of the configurations for a single part can take a couple of hours, and in the few times I have done it, I have never seen the SolidWorks interface recover from starting the command, although it seems to finish. Having all of the configurations is very useful, especially if you are being plagued by the Huge Screws.
529
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 530
Creating and Using Libraries
Settings tab The Settings tab is where you can set the config and part options. If you choose to create parts, then you also need to specify a location for the parts to be kept. If you choose a network location, it is best to use the UNC path, rather than a mapped drive because mapped drives may not reconnect on start up and may be mapped to different letters from computer to computer, but the UNC always points to the same location from any point on the network. The Settings tab also enables the Administrator to establish a password for Toolbox data configuration changes. The Settings tab is shown in Figure 17.22.
FIGURE 17.22 The Settings tab
Properties tab The Properties tab enables you to set up properties that appear in the PropertyManager. For example, you can enable fill-in or drop-down lists for values. Properties can be enabled for specific items, as shown in Figure 17.23.
Smart Fasteners tab The Smart Fasteners tab controls Smart Fasteners, which are discussed later in this chapter. The tab is shown in Figure 17.24. As an example of the types of settings you can use here, you can control which screw types are used with which types of Hole Wizard or non-Hole Wizard holes.
530
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 531
Using Hole Wizard and Toolbox
FIGURE 17.23 The Properties tab
FIGURE 17.24 The Smart Fasteners tab
531
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 532
Creating and Using Libraries
Using Toolbox Up to now in this chapter, we have looked at Toolbox mainly from the administrative point of view; now, we will look at it from the user’s point of view. Toolbox has two components: Toolbox and Toolbox Browser. In practice, the Toolbox component is actually ignored, and the Toolbox Browser component is generally referred to as Toolbox. The Toolbox Browser is the Task pane interface, and is found on the Design Library tab, as shown in the image to the left in Figure 17.25. The Toolbox component is found in the Toolbox dropdown menu. It includes structural steel shapes, grooves, cams, and beam and bearing calculators.
FIGURE 17.25 Toolbox and the Toolbox Browser
Turning Toolbox and the Toolbox Browser on You can turn on Toolbox and the Toolbox Browser through the Tools, Add-Ins dialog box. The column of check boxes on the left indicates that the add-in will be active for the current session of SolidWorks only. The column of check boxes on the right indicates that the add-in will be active every time the software starts up, as shown in Figure 17.26.
532
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 533
Using Hole Wizard and Toolbox
FIGURE 17.26 Turning Toolbox on in the Tools, Add-ins interface
Once the Toolbox Browser is turned on, you can use it by expanding the Task pane at the right of the SolidWorks graphics window and clicking the Design Library, which looks like a stack of books. In this panel, you will see the Toolbox screw symbol. Expand icons until you find the fastener or other hardware that you are looking for, and then drag the part into the assembly.
Populating holes Holes can be populated in several ways, such as dragging-and-dropping, populating multiple holes at once, and using feature-driven component patterns. I discuss manual and patterning options here, and Smart Fasteners in the next section.
Drag-and-drop The simplest way to bring Toolbox parts into an assembly is to drag-and-drop them. Position the part that the fastener goes into so that you can see the edge of the hole where the screw head will go. Then browse to the correct fastener, and drop the fastener onto the edge, as shown in Figure 17.27. Because of the use of Mate References in Toolbox parts, they know that they are supposed to snap into holes on flat faces. When dropping the fastener into the hole, the Smart Mate icon momentarily appears. A Smart Mate of this sort applies two mates, one that is concentric between cylindrical faces, and one that is coincident between two flat faces.
533
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 534
Creating and Using Libraries
FIGURE 17.27 Dropping a fastener onto a hole
Populating multiple holes at once Figure 17.28 shows the progression from a plate with holes in an assembly. In this example, you would select the edges of the holes, then select a fastener, and then choose Insert Into Assembly from the RMB menu, to fully populate the part.
FIGURE 17.28 Populating multiple holes at once in an assembly
534
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 535
Using Hole Wizard and Toolbox
Feature Driven component patterns Chapter 15 discussed Feature Driven component patterns (also known as derived patterns), where a pattern of parts in an assembly is driven by a feature pattern in a part. You can find this assembly feature in the assembly menus under Insert ➪ Component Patterns ➪ Feature Driven.
Smart Fasteners Smart Fasteners are Toolbox parts that know what holes they go into automatically. The database that holds all of the information for Toolbox part types and sizes also holds the information for the sizes of the holes. It is only natural that SolidWorks try to combine this information and use it to its best advantage. You can use Smart Fasteners in two ways:
Smart Fasteners with Hole Series One way to use Smart Fasteners is in conjunction with Hole Wizard Hole Series. Hole Series creates the holes through multiple parts at once, creating the appropriate type of hole through each part, and then Smart Fasteners automatically places fasteners in the holes, even including nuts and washers. To do this, you can select the option on the first panel of the Hole Series PropertyManager interface, as shown in Figure 17.29. If you are planning on using Smart Fasteners, using them in conjunction with the Hole Series is your best bet, using them in conjunction with the Hole Series holes.
FIGURE 17.29 The Hole Position interface
The Smart Fasteners with Hole Series is a function that you should be careful when using. It is very effective, but it may cost you some performance (speed). The Hole Series is an Assembly Feature (sketch) that drives several in-context features (holes), and then parts are mated to those in-context features (fasteners).
Smart Fasteners Populate All Smart Fasteners functionality also has an automatic component. Once an assembly has parts mated into place, you can place fasteners into parts with appropriate holes by face, by part, or for the entire assembly at once.
535
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 536
Creating and Using Libraries
You may not want to spend a lot of time trying to use this type of the Smart Fasteners functionality. I have tried to find examples where Smart Fasteners works well and predictably, but to no avail. I have searched through training examples, tutorial files from SolidWorks, and I have even made some of my own example files. I have looked for presentations from user groups and SolidWorks World that use Smart Fasteners, but no one appears to be talking about this functionality. Although in theory, it offers interesting functionality, in reality, it receives very little attention — definitely a warning sign.
CAUTION
The one assembly that I did find where Smart Fasteners worked surprisingly well (in fact, almost perfectly) was from the sample files that installed with SolidWorks. Upon closer examination, the reason this worked well was because it used assembly features for the holes, and so the holes did not appear in the individual parts. If that is the price that you have to pay just to get fasteners to populate automatically, then I would rather put them all in manually.
The limitations of Smart Fasteners Smart Fasteners have some documented limitations where you should not expect them to work: n Holes in single parts n Holes created by extruding a nested loop n A mirrored hole or cut features n Holes in mirrored, imported, or derived parts n Misaligned holes n Holes with a large difference in diameter n Holes with large gaps between them (a large gap in the axial direction) n Holes made using different techniques (such as sketch pattern versus feature pattern) If you would like to try out Smart Fasteners, then you can use the assembly included on the CD-ROM called Chapter 17 Smart Fasteners.sldasm. In this assembly, half of the holes are done correctly, and in the other half, the screws are put in either backwards or head-first. The documented method for flipping the fasteners is to expand the Smart Fastener, RMB click the series, and select Flip. In this case, my attempts resulted in success about half of time, which was somewhat higher than my attempts with other assemblies. In some cases, screws were put in the ends of shafts without holes, on filleted edges, and unfortunately missed most of the places that I did want the screws to go.
536
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 537
Using Hole Wizard and Toolbox
Organizing Toolbox parts in an assembly Assembly FeatureManagers are hard enough to manage when they become full of parts; they become even more unmanageable when they also need to include the many types of fastener parts. As a result, I recommend that fasteners, as well as any other type of part that is found in large quantity in the assembly, be organized into folders, as shown in Figure 17.30. You should also group parts of the same size or function together.
FIGURE 17.30 Organizing Toolbox parts into folders
Recommendations After spending almost an entire chapter saying what you should not do, it is finally time to say what you should do. Toolbox can be downright dangerous if you install and use it improperly; however, the following recommendations work in most situations.
The simplest setup that works If you are a single user who does not share files over a network with other users, then installing SolidWorks and Toolbox with the default settings should work for you. This appears to be the arrangement that the developers had in mind when they programmed the tool, because it is the only scenario in which it works as expected.
537
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 538
Creating and Using Libraries
Be careful if you ever receive an assembly from another Toolbox user, because this is the one situation that can cause immediate trouble. If they also send their Toolbox parts, then I recommend that you open all of their Toolbox parts before you open their assembly, so that the assembly is certain to access their Toolbox parts instead of yours. If you need to include materials and mass-populate custom properties, then I recommend that you go through the exercise of building all of the configurations of all of the parts, and then use an auto-created design table to drive the properties. If you have more than one user, then this technique will not work for you, unless both users work independently from one another.
A complete setup that works If you have multiple users that share assemblies, then you need to also share the Toolbox library. If you share assemblies only among yourselves, meaning only with other users who are also sharing Toolbox, then sharing Toolbox should be good enough. However, if you share assemblies with Toolbox users who do not share your Toolbox library, then you should probably go through the exercise of populating all of your parts with all of the available configurations. Setting your library to use the Create Parts setting cannot help you to avoid the Huge Screws problem when you receive an assembly from outside your group. If the originator has used parts with configurations, then you must also use configurations. If you do not receive assemblies from outside of your group with Toolbox parts in the assembly and you have network performance problems, then it may be a good idea to install Toolbox locally, but to set it to use the Create Parts setting, where the parts are on a shared network location. If you use a PDM system, then I would definitely install Toolbox locally, and use the Create Parts setting. The sharing occurs through the PDM system. The least problematic technique is to turn Toolbox off altogether and either buy or make your own library of static parts. You can then distribute these files internally in your organization, as well as to any other people upstream or downstream from you who also share files with you. You can build this type of library by using Toolbox’s config population tool; materials or other custom properties are then dealt with the way you want, probably using auto-created design tables.
Tutorial: Gaining Experience with the Hole Wizard and Toolbox Figure 17.31 shows a section view of the assembly used for this tutorial. Notice that there is a gasket under the Sensor part.
538
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 539
Using Hole Wizard and Toolbox
FIGURE 17.31 A section view of the tutorial assembly
This tutorial assumes that you have a working copy of Toolbox running on your computer. If you do not have Toolbox, then you can proceed to the next chapter. This tutorial also assumes that your Toolbox is using the default Create Configurations setting, although it can also work with the Create Parts setting. To get some experience using this tool, follow these steps: 1. Open the assembly from the CD-ROM called Chapter 17 Tutorial.sldasm. 2. Make sure that the Toolbox Browser is turned on by selecting Tools ➪ Add-Ins ➪ Toolbox ➪ Toolbox Browser. 3. Expand the Task pane, found on the right side of the graphics window, and display the Design Library panel, which contains the Toolbox icon. Expand the ANSI Inch standard, and the Bolts and Screws folder, and finally click the Hex Head bolt, as shown in Figure 17.32 on the left. Drag-and-drop the hex head bolt into the indicated hole. It snaps into place because of the Mate Reference that is used on the Toolbox part. Use the settings shown in the PropertyManager to size the bolt.
NOTE
The Vendor text box that displays in the PropertyManager above will not be available to you unless you have customized the Properties tab in the Configure Data Settings dialog box.
4. Add a flat washer and nut to the bolt, as shown below in Figure 17.33. The washer is Plain Washer Type A, Preferred - Wide Flat Washer.
The nut used is Hex Nut, Heavy Hex Nut.
539
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 540
Creating and Using Libraries
FIGURE 17.32 Select and place a fastener.
Drop hex head bolt here
540
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 541
Using Hole Wizard and Toolbox
FIGURE 17.33 Specifying the washer and nut
541
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 542
Creating and Using Libraries
5. Notice that the bolt is too short, as shown in Figure 17.34. RMB click the bolt, either in the graphics window or in the FeatureManager, and select Edit Toolbox Definition, toward the bottom of the menu. Change the length of the fastener to 1.625 inches.
FIGURE 17.34 The bolt is too short.
TIP
Use the Dynamic Preview option at the bottom of the Toolbox PropertyManager. After you select a new size, the bolt in the graphics window immediately updates to reflect
the new size. The selection of which hole the first fastener was positioned in could be arbitrary on this assembly because it uses a circular pattern, but if it had been a rectangular pattern, then the order would have mattered. When preparing to use a Feature Driven component pattern, it is important to put the components in the seed feature (the original feature that the pattern was created from).
TIP
NOTE
542
If you try to apply Smart Fasteners to the hole, then you will notice that the fastener is placed incorrectly. This is another situation where Smart Fasteners are a problem.
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 543
Using Hole Wizard and Toolbox
6. Create a Feature Driven component pattern (Insert ➪ Component Pattern ➪ Feature Driven) using the circular pattern of holes on either the Top or Base parts. Pattern the bolt, washer, and nut all in the same component pattern. 7. Zoom in on the sensor on the top of the assembly. There is a gray gasket between the orange sensor and the blue top parts. Click one of the flat ends of the sensor part and then click the Hole Series toolbar button, or select Insert ➪ Assembly Feature ➪ Hole ➪ Hole Series.
TIP
Remember that the pre-selection of a flat face is important so that you can use a 2D placement sketch, rather than a 3D placement sketch.
8. Make sure that you select the Add Smart Fastener option, as well as the Create New Hole option. 9. Make three sketch points and use construction geometry and dimensions to locate the holes, as shown in Figure 17.35. The size and types of holes are determined in a later step. (This is from the reverse of the normal Hole Wizard, where you first determine the type and size of hole, and then you establish the positions.)
FIGURE 17.35 The positions of holes in step 9
10. Click the Next button (the blue arrow pointing right) to move to the First Part hole specification. Set it to a counterbored hole, for a #10 binding head screw, with a head clearance of .025 inches, as shown in Figure 17.36 in the image to the left. Click the Next button to advance to the Middle Parts hole sizing. 11. In the Middle Parts PropertyManager, make sure that the Auto Size Based On Start Hole option is on, as shown in Figure 17.36 in the middle image. This creates a normal fit clearance hole for the gasket part. Click Next to advance to the hole definition for the Last Part.
543
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 544
Creating and Using Libraries
12. In the End Hole Specification panel, make sure that you select the Hole rather than the Tap option, as well as the Auto Size Based on Start Hole option. This is shown to the right in Figure 17.36. When this step is complete, click the OK button (the green check mark icon).
FIGURE 17.36 Sizing the holes
The interface here looks unfinished. Notice that the Fit text box is available for the End Hole, even if you use the Auto Size Based on Start Hole option, but it was not available for the Middle Part. Also notice the lack of drop-down arrows for the Fit and Size text boxes.
NOTE
13. The Smart Fasteners PropertyManager appears. Expand the Binding Head Screw header in the Fasteners panel, and notice the warning icon on Series1, as shown in Figure 17.37. When you click this warning icon, a message displays in the Information panel at the top of the PropertyManager window. This particular flag suggests that there may be an interference; however, there is no interference. This warning disappears when the feature is finished.
544
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 545
Using Hole Wizard and Toolbox
FIGURE 17.37 The Smart Fastener PropertyManager
14. Add a washer and a nut to the bottom stack of the binding head screws. This is easy to do, and almost makes up for the rest of the Smart Fasteners shortcomings. To do this, RMB click the Bottom Stack entry at the bottom of the Fasteners panel and select the Bottom Stack option that pops up. 15. A dialog box appears, enabling you to add a washer and a nut, as shown in Figure 17.38. You may want to roll the model over so that you can see the components being added to the underside of the screw. You can add other properties to the parts using the Properties button. Notice that the screw has been lengthened to accommodate the added components.
NOTE
If you add a washer to the top stack, the hole does not automatically become larger, and it may cause an interference. Be careful about your choice of top-stack washers.
545
17
25_080139 ch17.qxp
Part IV
3/26/07
4:02 PM
Page 546
Creating and Using Libraries
FIGURE 17.38 Adding washers and nuts
You may have noticed that this time, Smart Fasteners worked almost flawlessly and certainly saved you some time. Although this tool is not applicable to other purposes, when used with the Hole Series, it is quite useful.
NOTE
16. You may want to group the fasteners and even the fasteners’ mates into folders, as shown in Figure 17.39. The version of the assembly labeled Finished on the CD-ROM may open up on your computer with Huge Screws if you open it before completing the tutorial. This is because the configurations used in the assembly are on my computer. Although you have the same parts, before doing this tutorial, you may not have the same configurations, and so they cannot be found and come in Huge instead. This was intentional; it is a practical reminder of this problem and how easily it can happen to you. If you are using SolidWorks 2007, you should be able to tell Toolbox to simply recreate the sizes and continue on. If the assembly provided on the CD-ROM had been made prior to SolidWorks 2007, that option would not exist.
CAUTION
546
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 547
Using Hole Wizard and Toolbox
FIGURE 17.39 The finished Assembly FeatureManager interface
Summary The Hole Wizard can make holes based on 2D or 3D sketches. The type of hole that you create depends on whether or not you have pre-selected a flat face before clicking the Hole Wizard tool. Two-dimensional sketches are far easier to use than 3D sketches. I have met people who claim to have had good success with Toolbox even in a shared environment, but since the problems with the tool are so easy to demonstrate, these people are either extremely disciplined or extremely lucky. For all users except those who work alone and do not share files with other Toolbox users, Toolbox can cause a number of major problems. You can develop techniques to prevent you from experiencing Huge Screws, for example, either not sharing assemblies with other Toolbox users or pre-populating all of your configurable parts with all possible configurations. Further, Smart Fasteners that you use in conjunction with Hole Series violate any best practice guidelines that you could name when it comes to assembly performance and circular references; however, if you can work with that, then it is a really sophisticated technique.
547
17
25_080139 ch17.qxp
3/26/07
4:02 PM
Page 548
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 549
Working with Library Features
L
ibrary features are features that you create once and re-use many times. They are intended to be parametrically flexible to fit into many types of geometry, but they can also be of a fixed size and shape. All of the information that you have learned in previous chapters about designing for change, and design intent, will be used here, and you will also learn how to create, use, and store library features in this chapter.
Using Library Features Library features reside in the Design Library, which is located in the Task pane to the right of the graphics window. You can actually detach the Task pane from its docking location and move it wherever you want, leave it undocked, or even dock it to the left side of the screen.
TIP
If you are a long-time SolidWorks user, then you may still know the Design Library as the Feature palette. Another change to the old library features and palette features is that they have been combined, thus removing some of the limitations of the old palette features. You can use library features for snap rings, grooves for o-rings, custom holes (you can even customize a Hole Wizard hole and put it in the library), mounting bosses for plastics, mounting hole patterns, electrical connector holes, and so on.
549
IN THIS CHAPTER Using library features Creating library features Tutorial: Working with library features
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 550
Creating and Using Libraries
One very useful aspect of library features is that they can be driven by configurations and design tables. Once the feature is in the part, the configurations are still available, and so you can change the config of an applied library feature at any time. You can also link a library feature to an external file. This enables you to change a feature or set of features in several parts at once, if they are all externally linked to the file.
Getting started with library features Library features are simple to use, but difficult to set up. For that reason, this chapter discusses using them first, so that you know what kind of behavior you are trying to create. As a result, setting them up should make a little more sense. To use a library feature, you just drag and drop it onto the appropriate geometry. You are then prompted to select references in the new part that match the base geometry that the library feature is attached to. You can be fairly creative with references, but one of the goals is to make the library feature work with as few references as possible, in order to make it easy, fast, and reliable to use. SolidWorks software installs with several sample library features in the Design Library. The following demonstration uses some of these standard library features. Later, you can add library features from the CD-ROM to the Design Library.
The Library Feature interface Library features work best if they go from a certain type of geometry to a similar type of geometry, for example, from rectangular to rectangular, or from circular to circular. This is because the relations or dimensions that link the feature to the rest of the part tend to be dimensions from straight edges or concentric sketch relations. Of course, there are other ways of applying library features, but these are the most prevalent. Library features can be applied unconstrained and then constrained, or moved later, but the process is cleanest when it all just falls together correctly the first time.
Task pane You do not have to save the part or do anything special before applying the library feature. All you need to do is find the Task pane. The Task pane is the window that flies out from the right when you open SolidWorks. You may have turned it off and forgotten about it, in which case you can turn it back on by selecting View ➪ Task pane. The Task pane automatically closes when you click outside of it unless you pin it open using the push-pin icon in the upper-right corner of the window. When you do this, any toolbars that appeared on the right side of the Task pane control tabs are moved out and positioned between the graphics window and the Task pane, which now remains open by default.
550
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 551
Working with Library Features
You can also detach the Task pane by dragging the bar at the top of the pane. Figure 18.1 shows the Task pane docked to the right side of the SolidWorks window.
FIGURE 18.1 The Task pane docked to right side of the SolidWorks window
If you are using dual monitors, you can drag the detached Task pane onto the second monitor, which allows you to use the Task pane, and at the same time gives you more room in the graphics area. This must be done each session; the Task Pane does not remember positions on a second monitor.
TIP
Design Library The Design Library tab displays an image of a stack of books. It is the overall library area for all sorts of elements in SolidWorks, which I will discuss later in this chapter. The only part of the Design Library that concerns us right now is the Features folder. If you expand this folder, you can see that it is populated with some sample features. Open a new part and create a cylinder using any method you want (for example, extrude, revolve). Make the diameter three inches, and the length a little more than one inch.
551
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 552
Creating and Using Libraries
In the Inch features folder, click the folder called o-ring grooves. The first feature in the list is called face static – gas. Drag-and-drop this feature onto the end flat face of the cylinder. As shown in the image to the left in Figure 18.2, the PropertyManager displays a yellow information panel explaining the process. The next step is to select the configuration, as shown in the image to the right in Figure 18.2. Not all library features have multiple size configurations, but these ones do. The configs in this case are driven by design tables. Select configuration 330.
FIGURE 18.2 Placing the feature and selecting the configuration
When you select the configuration, the interface changes. In this case, only a sketch relation locates the feature; it is not located by dimensions. Notice that in the References panel shown in Figure 18.3, there is an Edge entry with a question mark. This means that the library feature needs a circular edge to locate it. Notice that a small window appears, displaying the library feature. You may not be able to distinguish it in Figure 18.3, but the circular edge around the face that the library feature is on is highlighted in green. This indicates that you need to select an edge that has the same relation to the library feature as the highlighted edge. Pick the circular edge of the part on the end of the cylinder where you want to place the library feature. Next, use a rectangular part where the library feature is located by using dimensions rather than sketch relations. Create a rectangle, 1.5 inches by 2 inches, and extrude it to about 2 inches in depth.
552
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 553
Working with Library Features
FIGURE 18.3 Locating the library feature
Next, in the Design Library, browse to features, then inch, and then the fluid power ports folder, and drag the sae j1926-1 feature onto the end of the extruded rectangle. Select the 38-24 size from the configurations list. A window appears, prompting you for reference selections, as shown in Figure 18.4.
TIP
It is often helpful to orient the part that is receiving the library feature in the same way as the part shown in the preview window. This helps you to visualize which edges to
select.
After the locating edges have been identified, the Locating Dimensions box becomes active, and you can change the values of the dimensions to locate the feature. Further, in the Size Dimensions pane at the bottom of the PropertyManager, clicking the Override Dimension Values option allows you to change dimensions of the feature itself. When you use a library feature with a design table, the design table is not brought into the part with the library feature. If the part already had a design table, this would cause multiple tables, which is not currently possible in SolidWorks.
553
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 554
Creating and Using Libraries
FIGURE 18.4 Placing a library feature with dimensions
If you override the feature dimensions when feature configurations already exist, then a new configuration is created in the list of feature configurations called Custom Configuration. It appears that multiple custom configurations are not allowed, and so if you have to make changes, then you must ensure that they are right before you use the library feature in a part.
Other Design Library functions The Design Library has other functions besides library features. For example, you can use it as a repository for other items that you use frequently.
Annotations You can store commonly used annotations in the Design Library. If you look at the Annotations folder with the default sample annotations, you see a combination of symbols and blocks. You can use symbols and notes in 3D models, but you can only use blocks in sketches or 2D drawings. Keep in mind that not all annotation types can be used in all places.
554
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 555
Working with Library Features
Annotations can be stored in the library as favorites or blocks. Many file extensions are used for different types of favorites, but they typically begin with *.sld and end with fvt, as in *.sldweldfvt. Figure 18.5 shows the default location of the Design Library, and the Thumbnail view of the favorites and blocks in the Annotations folder.
FIGURE 18.5 The Annotations folder in Windows Explorer
Location of the Design Library folder If you frequently work with different types of annotations, then you should organize the library into sub-folders to separate symbols, annotations, and blocks, and move these folders to a different location. By default, the Design Library folders are found at <SW install dir >\data\design library\. You should store them to another location, not in the SolidWorks installation directory, but in an area that you have selected to maintain SolidWorks data between releases. For example, I have a folder at D:\Library that contains folders for macros, templates, library features, library parts, favorites, and so on. You can easily back up or copy these files from one computer to another, although you must quit SolidWorks before making these changes. After moving the library, you have to point SolidWorks to the new location. To do this, select Tools ➪ Options ➪ File Locations ➪ Design Library. Delete the old location and browse to the new location. You should move other items in this list and redirect any items that you use, such as the templates and any other items you use frequently. Once you have specified the settings, they should be retained when you install service pack upgrades or future versions.
Library Parts The Design Library can also store commonly used library parts. One of the advantages of using the library for parts is that on placement into the assembly, if configurations are available in a part, then a window pops up, enabling you to select which configuration to place into the assembly. In many cases, using the Design Library for Library Parts is thought to be an acceptable replacement for the automated function of Toolbox. If you use Toolbox to make the parts and populate them with configurations, and then save the parts out of Toolbox and into the Design Library, many options, including naming conventions, and more flexible use of custom properties become available that are not available through Toolbox.
NOTE
555
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 556
Creating and Using Libraries
Figure 18.6 shows the configuration selection window. Note that this is alphabetically listed, and you can type in the box to go to the configuration that you want.
FIGURE 18.6 Inserting library parts with configurations
Parts inserted from the library parts folder can also take advantage of the Mate References functionality in the same way as Toolbox, by allowing parts to snap into place.
Sheet metal forming tools Sheet metal forming tools are only mentioned here as a part of the library. They work much like other library features, but they do so within the specialized functions of sheet metal parts in SolidWorks. Sheet metal forming tools are discussed in Chapters 29 and 30.
Assemblies You can use library assemblies in SolidWorks in the same ways that you use library parts, because they are inserted into the top-level assembly as a sub-assembly. For sub-assemblies that require motion, such as universal joint sub-assemblies, you can set the sub-assembly to solve as flexible.
TIP
When saving assemblies to the library, it is recommended that you put the parts in a separate folder to segregate the parts of different assemblies.
Routing Routing is a separately purchased add-in that is included with SolidWorks Office Premium. It includes piping, tubing (rigid and flexible), and wiring. Routing makes extensive use of libraries and automation, but is not part of the scope of this book.
Smart Components Smart Components are components that resize by automatically selecting configurations, depending on the size of the geometry onto which they are being dropped. For example, a clamp with many sizes driven by configurations would select the correct config when dropped onto different sizes of cylinders. This is a very useful tool. Smart Components are discussed in Chapter 19.
556
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 557
Working with Library Features
Creating Library Features When you save library features to the library, they use the file extension, *.sldlfp (library feature part). They must contain some base geometry, which simulates the part onto which the feature will be dropped. The base geometry is not transferred to the new part; only features that are marked with the “L” in the FeatureManager (for Library) are transferred to the new part. Figure 18.7 shows the FeatureManager of a library feature part.
FIGURE 18.7 The FeatureManager of a library feature part
Creating a library feature When creating a library feature, the first problem that you need to solve is how the feature will be located on a new part. Does it need to be placed on cylindrical parts, rectangular parts, other types of shapes, or does this matter at all? Will the feature be located by using dimensions or sketch relations, or will it just be placed underdefined and later fully defined manually rather than automatically? You may have noticed in one of the earlier examples that the sample fluid power ports had two versions of the same feature. One version is intended for the feature to be placed on the flat end of a cylinder, and the other version is intended to be placed on a rectangular face.
A few limitations Library features can contain multiple features of different types. They may add and remove material, even within a single library feature. However, a few limitations exist. For example, they require a base feature, and multibody features and external references are not allowed, nor are sheet metal, weldments, or molds. In addition, you cannot add scale features to the library, nor can you apply library features to an assembly.
557
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 558
Creating and Using Libraries
Creating a new library feature To start a new feature, the first decision that you need to make is what shape to make the base. Is the feature a type that is usually going to go onto a single shape or multiple shapes? Regardless of your decision, you or whoever ends up using the feature will have the flexibility to change, or simply not use, the relations when you place the feature. For this example, I use a rectangular base. The library feature that I want to create consists of two boss extrudes, a cut extrude, and several fillets. Here is how it works: First, you need to create a rectangular extrusion. The size should be bigger than the feature that goes on it, and representative of the face of the end part onto which this feature will typically be placed. Next, in beginning to create the features that you want to reuse, it is very important that you pay attention to any references outside of the sketch; these include absolutely anything outside the active sketch, such as the sketch plane, references to edges, the Origin, other planes, other sketches, and axes. Although these references are allowed, each reference to anything that is not already part of the library feature must be reconnected when you place the feature on the part. The ideal situation is obviously a single drag-and-drop, but generally speaking, at least one other step is usually needed. The initial drag-and-drop determines the face for the feature to start from, and from there, you usually need to locate features, either by using relations or dimensions. A concentric dimension locates the feature in a single reference selection of a circular edge (although it may also need to be rotated), and dimensions typically require a dimension in the X dimension, and another one in the Y dimension. Figure 18.8 shows the base feature and the first feature of the library feature. The only relations between the sketch of the library feature and the base feature are the sketch plane and the two dimensions. Notice that names have been assigned to all of the dimensions, sketches, and features. This is because the dimension names all display in the interface. If you look back to Figure 18.4, in the Size Dimensions pane, dimension names make it easy to know which dimension to change, whereas the D1 dimension leaves you guessing as to what it applies to.
NOTE
FIGURE 18.8 Creating a library feature
558
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 559
Working with Library Features
You should ensure that subsequent features after the first one reference only the first feature of the library feature (which is the second feature in the part). This is not a mandatory requirement, but a helpful guideline. You can make additional references, but they should be limited to the same items that were already referenced, if possible. Users who model carelessly or do not pay attention to what they are doing, typically have trouble making library features that function and are easy to use. Now you can add the second extruded feature, being careful to reference only geometry that is going to move with the library feature. Figure 18.9 shows the newly added feature. If you would like to follow along with the building of this feature, you can open the part from the CD-ROM under the filename Chapter 18 First Library Feature.sldprt.
FIGURE 18.9 Adding the next feature to the library feature
Notice that a plane has been added. The plane is made to only reference geometry that is internal to the library feature; it is perpendicular to an edge at the midpoint, which simultaneously locates and orients the plane correctly to enable it to be used to mirror the Ear feature. Also notice that the EarSketch uses the same face reference from the base feature. This will appear in the Reference list as a single reference. SolidWorks has made some changes that affect library features in two ways that may not be immediately obvious. First, before SolidWorks allowed multibody parts, the first feature of the part was always called the base feature. This terminology remains, even though the concept of a base feature is obsolete. (The first feature in a part may be reordered so that a different feature becomes first.)
NOTE
Second, SolidWorks used to distinguish between palette features and library features. Palette features were limited to a single reference, and library features were a bit less user-friendly but more powerful. They have been combined and improved to what we have today.
559
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 560
Creating and Using Libraries
Saving the library feature You can use two methods to save a library feature. You can either drag-and-drop into a Design Library folder, or use the Save As method. Because Save As is a little more common, I will describe it first. The first step in saving the library feature is to select all of the features in the FeatureManager that are intended to be a part of the library feature. Collapse the features first so that the sketches belonging to features are not selected. If the sketches are selected you may get a warning message saying that all of the selected features cannot be used in the library feature. Do not worry; the sketches still will be included. Remember that you can Ctrl-select individual features, Shift-select a range, or click-anddrag a box in the FeatureManager to select multiple features. Also keep in mind that if you do not select a feature (other than the base feature), then it will not be placed into the part when you insert the library feature. If there were any relations to the omitted feature, they may display as errors or warnings when you place the feature.
TIP
With the features selected, click File, Save As, and under Files of Type drop-down list, select the *.sldlfp file type. Browse to the Design Library folder, and save the part. Figure 18.10 shows the FeatureManager of the finished library feature.
FIGURE 18.10 The finished library feature part
Display of the Library Feature icon During the Save As process, a new folder was added to the Design Library named Bosses, as shown in Figure 18.10. Notice the new icon for the library feature in the lower window. You may notice that some of the default library features saved in the Design Library have a bluish background. This
560
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 561
Working with Library Features
occurs because of the SolidWorks viewport background color, which you can set in Tools, Options, Colors. Even if you never see that color because you are using a gradient background, SolidWorks still uses the color specified by that setting as the background when saving thumbnails and previews. I always set this color to white for this reason, so that document backgrounds in previews do not have the blue color. You may want to orient and zoom the library feature before saving it, so that it displays clearly in the panel. One of the techniques that I like to use is to make the base feature a different color than the library feature itself; this helps you to more easily determine what is the geometry that will be transferred and what is just dummy material. Figure 18.11 shows various settings for displaying the icons in the Design Library. Which one you select will depend on your screen resolution, the number of icons that you want to display, and the quality of the preview images.
TIP
FIGURE 18.11 Display modes for the Design Library
561
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 562
Creating and Using Libraries
The real test for a library feature comes when you actually use it. This feature is recreated perfectly on the new part, but I noticed one problem. When the feature was placed, it was 90 degrees away from the orientation that I wanted it to be in. It seems that the only way to make the feature rotatable is to create it with parallel and perpendicular relations rather than horizontal and vertical ones, so that one of the references can act as a rotation reference. Figure 18.12 shows the completed library feature placed on a part.
FIGURE 18.12 The completed library feature placed on a part
Once you place a library feature on a part, it can be edited, unless you select the Link To Library Part option in the Configuration pane, in which case the feature is driven externally from the *.sldlfp file. One of the available options is to dissolve the library feature so that all of the constituent features become regular features in the main part.
Creating a library feature from an existing part When creating a library feature from an existing part, you use essentially the same process, but it is actually somewhat more difficult to achieve the correct results. It is best to remove all of the
562
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 563
Working with Library Features
features that do not either form the base feature or go into the library feature itself. This can cause a lot of broken references. It may be better to use a different technique such as creating a new part with only the base feature. You can then Ctrl-drag the desired features from the existing part to the new part, set up the rest of the library feature, and save it with a *.sldlfp extension. You can also create a library feature by dragging and dropping, although there are some limitations with this technique that seem to override the convenience. However, there is a workaround for the biggest limitation. If you select faces from features and drag them into the lower Design Library window, then an Add to Library PropertyManager interface appears to enable you to start creating a library feature. The Add to Library PropertyManager interface is shown in Figure 18.13. You must select the features from the flyout FeatureManager. This is the source of one of the limitations. In our example, the plane cannot be selected by this method. The workaround for this is to complete the feature without the plane, RMB click the icon in the Design Library window, and then select Open. With the library feature open in its own window, RMB click the plane feature and select Add to Library; that individual feature is then added.
FIGURE 18.13 The Add to Library PropertyManager interface
563
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 564
Creating and Using Libraries
Adding folders to the library You can add folders to the library in two ways, either by RMB clicking in the Design Library window and selecting New Folder, or by using the Windows Explorer interface. Another RMB menu option is Add Existing Folder, which enables you to add a folder from another location to the library. The folder is not moved or copied, but a shortcut is added to the Design Library, and the contents appear in the lower pane. After a library feature has been edited, or folders or documents have been added to the library using Windows Explorer, you can press F5 in either the lower or the upper window to update the display for that window, or by using the Refresh icon located at the top of the Task pane.
TIP
Tutorial: Working with Library Features This tutorial guides you through customizing a Hole Wizard hole to use as a specialty library feature, then storing it in the library, editing it, and placing it in a part. Follow these steps: 1. Open a new part, and create a rectangular base feature, about three inches high by three inches wide, and three inches deep. 2. Pre-select a flat face and start the Hole Wizard. 3. Create a counterbored hole for a Heavy Hex Bolt, 1⁄2-inch, Normal Fit, Blind, 1.2 inches deep. Locate the hole with dimensions from two perpendicular edges, as shown in Figure 18.14. Click the green check mark icon to accept the hole settings.
FIGURE 18.14 Placing a hole
564
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 565
Working with Library Features
4. Select Tools ➪ Options ➪ General, and turn on Show Dimension Names. 5. Double-click the counterbored hole feature in the FeatureManager to show the dimensions. RMB click one of the dimensions that you created to locate the center of the hole, and select Properties. 6. Rename the dimension using different names, so that they will have meaning when you place the dimension, such as XDir, or YDir. Do this for both dimensions. 7. Edit the second sketch of the hole. Figure 18.15 shows what the sketch should look like before and after the edit. Do not delete any of the named dimensions in a normal or revised Hole Wizard hole. SolidWorks has a checking mechanism that looks for these names, and it will display an error if the named dimension is not there. If there is no use for the dimension, it still has to be there, although it does not need to be used for its original use. You could rename another dimension with the name or simply dimension the centerline or an otherwise unused construction line. It does not matter about the function of the dimension, as long as there is a dimension with that name in the sketch.
CAUTION
TIP
You should also name any new dimensions that you may want to change. These dimensions will have more meaning when you are placing the feature if they have names.
FIGURE 18.15 Reconfiguring the hole
Remember that to get the diameter dimensions shown in Figure 18.15 (instead of radius dimensions), you must use the dimension tool to select the centerline (construction line) and the line or endpoint on one side, and then move the cursor to the other side of the centerline to place the dimension (the order of selection does not matter). When the cursor crosses the centerline, the dimension will display as a diameter instead of a radius.
TIP
565
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 566
Creating and Using Libraries
8. When you are done editing the sketch and renaming dimensions, exit the sketch. 9. Click the CBORE feature twice, or click it once and press F2, to rename it as SpecialHole. 10. Pre-select the same flat face that the first hole feature was placed on, and start the Hole Wizard again. 11. Place a #8-32 tapped hole, accept the default depth, and specify a center-to-center distance of .75 inches between it and the SpecialHole. Rename the radial dimension as MountRad. 12. Using the temporary axis through the center of the SpecialHole, make a circular pattern of the new tapped hole, creating a total of four instances of the tapped hole. Make the SpecialHole Feature red, and the tapped hole and pattern yellow. 13. Split the FeatureManager window into two by using the splitter bar at the top. Change the lower panel to the ConfigurationManager. 14. Rename the Default configuration to Size1. 15. Create a new configuration called Size2. Double-click the SpecialHole feature and change the dimension named C’Bore Dia to 1.5 inches. Be sure to change to This Configuration Only, using the drop-down menu. 16. Make a dimension change for the MountRad dimension to 1 inch. The results to this point are shown in Figure 18.16.
FIGURE 18.16 The results after step 16
17. Auto-create a design table by selecting Insert ➪ Design Table, and then selecting the Auto-Create option. Edit the design table to look like Figure 18.17. Remember that to fill the first two columns up to Size5, you can make the two-by-two selection of the Size1 and Size2 entries in the first two columns, and pull down the handle in the lower-right corner of the selection box until the appropriate boxes are filled.
TIP
566
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 567
Working with Library Features
FIGURE 18.17 The design table for the SpecialHole feature
18. Manually fill in the C’Bore Dia values, but in cell D3, type the equation =C3/2+.25. Then use the same Fill technique to populate cells D3 to D7. 19. Test the configurations to make sure that they all work. 20. In the Design Library, browse to a folder where you would like to put this library feature. (Make sure that it is not used by assemblies or sheet metal forming tools.) Click a face created by the SpecialHole feature, and drag the feature into the lower pane of the Design Library. The Add to Library PropertyManager should appear on the left. 21. Although you selected a feature and dragged it into the library, the Items to Add field appears blank. Select the SpecialHole, tapped hole, and circular pattern features, either through the split FeatureManager or the flyout FeatureManager. Selecting the features from the graphics window does not work. 22. Position and zoom the view of the part so that when it is saved, you see a good preview of the library feature. Also, if you have not changed your background color from blue to white, this would be a good time to do so. 23. In the Save To pane, make sure that you select the correct folder, then fill in a filename, and click OK. Figure 18.18 shows the completed PropertyManager interface for this function.
TIP
You may notice that there are two library entries in the window. This is because an additional path has been added in Tools ➪ Options ➪ File Locations ➪ Design Library.
24. If the new library feature does not appear in the Design Library, then click in the Design Library and press F5. If you do not like the way that it displays, then RMB click in a blank space inside the lower library window and select one of the other three options. 25. To edit the preview image of the feature, RMB click the feature in the Design Library window, select Open, reposition or zoom the view, and save it. Click in the Design Library and press F5 again.
567
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 568
Creating and Using Libraries
FIGURE 18.18 Saving the library feature
It is recommended that when placing a library feature, you should close the original library feature window. The workflow proceeds much more smoothly if the part is closed before you use it.
TIP
26. Open the part from the CD-ROM called Chapter 18 Tutorial Blank.sldprt. If you would like to examine the version of the SpecialHole part that I created, it is stored with this data as well. 27. Drag the SpecialHole library feature from the Design Library onto the face of the blank part. Place the feature near the squared-off end. Select a configuration from the list in the PropertyManager. Although there is no prompt, when the Library Feature interface hesitates and there are configurations in the library feature, it is waiting for you to select a configuration. A prompt actually does exist, but it appears in the lower-left corner of the screen on the status bar in a tiny font, and most users probably do not notice it.
TIP
28. Try to orient the part in the same way that it appears in the preview window, as shown in Figure 18.19.
568
26_080139 ch18.qxp
3/26/07
4:08 PM
Page 569
Working with Library Features
FIGURE 18.19 Orienting the part and selecting references
29. Select edges on the Blank part that correspond to the preview window. Click OK to accept the placement of the feature. 30. Double-click the SpecialHole feature and change the X and Y placement dimensions to place it one inch from the edges in both directions. You may remember from Chapter 10 that library feature configurations cannot be controlled by part configurations. In order to show different library feature configurations in different part configurations, you need to suppress one library feature and insert another. This is the best available workaround. It may be time to visit that enhancement request site again.
NOTE
31. Place another library feature onto the blank part. Select a configuration, and click the green check mark icon, without selecting edges for the references. 32. Notice that the feature in the FeatureManager appears with an exclamation mark. If you investigate the cause of this, then you can see that the two dimensions that should be attached to edges are dangling because you did not select the references while placing the library feature. This was done on purpose to show a different technique. 33. Expand the library feature and the SpecialHole feature, and edit the first sketch in the Special Hole. This is the placement sketch. Delete the two dimensions that appear in dangling colors.
569
18
26_080139 ch18.qxp
Part IV
3/26/07
4:08 PM
Page 570
Creating and Using Libraries
34. Add a concentric sketch relation between the placement point and the arc edge of the Blank part. Exit the sketch. The error message should now be gone and the hole should now be placed in the center of the arc. 35. RMB click the second library feature and select Dissolve Library Feature. When you dissolve a library feature, you lose any access to any configurations. Some users insist on dissolving every library feature, so that they can see regular features in the FeatureManager. This technique may also be useful if you would like to reorder some of the individual features within the library feature.
NOTE
36. Figure 18.20 shows the finished part and FeatureManager. Good job!
FIGURE 18.20 The finished part
Summary Library features are very useful in automating frequent design tasks. They are easy to create, easy to store, and easy to apply. Setting up the features for the most flexibility often takes careful planning and attention to the detail of the references that you use.
570
27_080139 ch19.qxp
3/26/07
4:09 PM
Page 571
Using Smart Components
S
mart Components are one of the better design automation tools to come from SolidWorks in the last several releases. This is functionality that can save you a lot of time; the more standard items that you insert into your assemblies, the more time it can save you. Smart Components are parts or assemblies that you can place into an upperlevel assembly and that carry with them mounting features and hardware (cut-outs, mounting holes, and even fasteners). Smart Components are configurable, and can automatically size themselves on cylindrical parts.
Understanding Smart Components A Smart Component can comprise several elements: n A single part or an assembly that may use size configurations n A configurable library feature that usually serves as mounting holes or a viewing window for the Smart Component n Associated hardware that may also be driven by sizes n A training assembly that is used to define the Smart Component Some minor limitations exist, as you might expect: n A Smart Component part cannot have references that are external to the Smart Component group of which it is a member n When placed in the assembly, the associated library feature can only affect one component
571
IN THIS CHAPTER Understanding Smart Components Using Smart Components Making Smart Components Tutorial: Working with Smart Components
27_080139 ch19.qxp
Part IV
3/26/07
4:09 PM
Page 572
Creating and Using Libraries
n The associated library feature is limited to one of several feature types: n Extruded or revolved cuts or bosses n Hole Wizard holes n Simple hole features The setup time for Smart Components can be significant for the first one or two that you create, especially if you choose the auto-size option. The complexity of setup depends mainly on the number of configurations and configured parts that you use. The auto-sizing function takes the most time to set up because it requires matching configurations, and the auto-size table takes a while to manage, especially for multiple parts. Still, if you end up placing a given part with associated features and other components many times manually, this is a technique that can save you a lot of time.
Using Smart Components Figure 19.1 shows a simple assembly. It took approximately 20 minutes to model all of the parts, set up the Smart Component, and test it in an assembly. This example does not use auto-sizing, but it does use an in-context feature and two instances of a single hardware piece. This is an excellent example of Smart Component functionality because it is fast to create and fast to apply, and saves you some time whenever you use it.
FIGURE 19.1 A simple Smart Component
Getting started with a simple Smart Component In this assembly, you first place the electrical connector part in the assembly, mate it in place, and then apply Smart Components. You can apply Smart Components by clicking the Smart Component icon that appears on the part in the graphics window when you select it. SolidWorks
572
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 573
Using Smart Components
then prompts you to select the inside and outside faces of the sheet metal part (the hardware references the outside, and the cut-out feature references the inside). SolidWorks then creates the cutout as an in-context feature that it places in the sheet metal part.
TIP
This in-context feature is why the Smart Component is limited to affecting a single part.
When you create the Smart Component, a new folder is added to the FeatureManager of the component. This folder contains all of the required information about the other elements, such as the incontext feature, any other parts that go with the Smart Component, the “training assembly” location, and the face references to locate everything. Figure 19.2 in the image to the left shows this folder in the connector part that is used in this example. The image to the right shows what is added to the assembly FeatureManager when you add a Smart Component. The only thing that existed in the design tree shown in Figure 19.2 before the Smart Component was the Test Box sheet metal part.
FIGURE 19.2 The Smart Component folder in the connector part
Feature tree of Smart Component
Feature tree of assembly where a Smart Component has been used
573
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 574
Creating and Using Libraries
A star appears on the part symbol at the top of the FeatureManager, indicating that the part is a Smart Component. You can place this Smart Component by following these steps: 1. Create an assembly, and add the target part to it. The target part is the one that the Smart Component will be mated to, and the one that will have the in-context cut-out inserted into it. It is a good idea to save the assembly before you add the Smart Component to it. If the Smart Component is placed before the assembly is saved, the assembly has a tendency to forget that it has not been saved, and bumps the in-context feature to out-of-context when the name is changed from whatever the default name is (for example, Assem1.sldasm) to the name that you assign to it.
CAUTION
2. Put the Smart Component into the assembly. You can do this in the same way that you would add any normal part, including from the Design Library. If you use a part frequently enough to make it into a Smart Component, then you are probably going to want to have it in the Design Library for quick access. In fact, you can add a Smart Component to an assembly without using any of the Smart Component options. 3. Mate the Smart Component in the assembly. In this case, it was done with a face-to-face coincident mate and a pair of distance mates. 4. Next, apply Smart Components by clicking the Smart Component symbol on the part. If this symbol does not appear, then select the part in the FeatureManager. Figure 19.3 shows the Smart Component symbol on the part. If you have inserted many instances of a Smart Component, then each instance has the option to apply the Smart Component features and associated components.
FIGURE 19.3 The Smart Component symbol on a part
5. At this point, an interface similar to that of the Library Feature interface appears, with the small prompt window and a box for selecting references, as shown in Figure 19.4. After you select the references, and click the green check mark icon, the Smart Component, as well as the Smart Feature (in-context feature) and associated hardware components, are placed, and the job is done.
574
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 575
Using Smart Components
FIGURE 19.4 The interface for adding the Smart Feature and additional components of the Smart Component
Auto-sizing Smart Components Auto-sizing is the ability of a Smart Component to select a size from a list of configurations, based on the size of geometry onto which it is being dropped. At this time, the only shape that can be auto-sized is the cylindrical shape. Figure 19.5 shows the effects of auto-sizing. Notice the two shaft holders. These are two instances of the same part, using different size configurations. When you drag the Smart Component over the small end of the stepped shaft, the configuration corresponding to that size appears. As you drag the part along the shaft and the shaft diameter increases, the next-larger Smart Component configuration appears. This is part of the functionality of Smart Components. Each configuration of the Smart Component is set up to fit onto a range of shaft diameters. If the diameter of the shaft is outside of the range or between sizes, then the Smart Component is not applied.
575
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 576
Creating and Using Libraries
FIGURE 19.5 A Smart Component with auto-sizing
Sizes are governed by a configurator table, which looks similar to a design table, but works somewhat differently. The configurator table relates the configurations of the Smart Component to configurations of the individual components, which may also change size with the Smart Component. This serves as a subset of the function of a design table in an assembly, assigning part configurations to assembly configurations. Figure 19.6 shows a sample configurator table made for the following assembly.
FIGURE 19.6 A configurator table
When you look at this table, you begin to understand why creating auto-sizing Smart Components is much more involved than in the previous example. The configurations of the Smart Component are listed to the left, and the individual part configs can be selected in each cell from a drop-down list of all available configs for that part. There is no way to set configs for multiple components at once, nor is there a copy-and-paste function. These shortcomings combine to make this format somewhat less user-friendly than an Excel-based design table.
576
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 577
Using Smart Components
Most notable are the Minimum and Maximum Diameter columns to the right. These columns supply the parameters that make the auto-size function work. While the range of sizes used here is too large for real-world design (+/– .050 inches), it serves to convey the idea. More importantly, SolidWorks understands that mating sizes are not always exactly equal, and the ability to use a range rather than exact values accommodates this very nicely, although it can be tedious to set up. Another aspect of the setup shown here is that it uses Toolbox parts. If you want to use the autosize functionality, then you need to be using configurations for Toolbox parts. You should pre-build all of the needed configurations, and ensure that the configurations are always available.
Making Smart Components The most important point to remember about Smart Component setup is that you need to do it only once for each Smart Component. The second most important point is that the first setup is the most difficult. After that, subsequent setups become much easier to create. Adding components to the Smart Component is not so time-consuming unless the additional components are also configured and also auto-sized. Smart Components must contain at least one associated component and one in-context feature, or have the configurator table filled out and functional. If you try to create a Smart Component from a standalone part, then nothing happens; the Smart Component interface simply closes. You may combine all three elements (associated component, in-context feature, and auto-size), but you must have at least one element.
Getting started with a simple Smart Component Because the electrical connector shown in Figure 19.1 has already been used to demonstrate the insertion of a Smart Component, it is used here to demonstrate how to create one. All that you need to make a Smart Component with an associated Smart Feature (in this case, a cutout and mounting holes) and mounting hardware (in this case, two stand-off screws) is the part itself. The part can even be an imported part (a Smart Component made from dumb geometry). From the CD-ROM for Chapter 19, open the file named Chapter 19 – Connector Start.sldprt. This part is shown in Figure 19.7. There is nothing special about this part. I modeled it in SolidWorks using standard features, and there are no configurations or special features. It represents an electrical connector that may be mounted in a sheet metal electrical enclosure.
577
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 578
Creating and Using Libraries
FIGURE 19.7 An electrical connector part
The first step in setting it up is to create a mock assembly with a dummy part representing the sheet metal box. The part does not need to be complex or even sheet metal for that matter; it just needs to be close to the thickness that you would expect it to be mounted to. The assembly is called a training assembly, not because you are learning how to make a Smart Component, but because you are training the Smart Component to be smart. 1. Make a simple rectangular part, approximately 4 inches square and about .06 inches thick. Save the part to your hard drive. Give a name to the part so that it is clear that it belongs to this training assembly. 2. Place the rectangular dummy part into a new assembly, with a name that is both unique and identifiable. 3. Put the connector into the assembly. Mate the part so that the flange is flush with the rectangular piece. Also use distance mates to locate the connector planes from the edges of the part, similar to Figure 19.8 in the image to the left. 4. Next, edit the dummy part in context, and offset edges of the connector part to extrude a cut, as shown in Figure 19.8 in the image to the right. Offset the two mounting holes and the area around where the connector will stick through the sheet metal by about .02 inches.
578
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 579
Using Smart Components
FIGURE 19.8 Placing the connector on the dummy part
5. Exit Edit Component mode and add two instances of the part named Chapter 19 – Smart Connector Hardware.sldprt to the assembly. Mate the hardware part to the in-context hole, making sure that it goes to the outside thickness of the dummy sheet metal part. I have spent a fair amount of time trying to convince you that it is a best practice to avoid mating parts to in-context features, and yet here I tell you to do exactly that. Another thing I have tried to stress is that best practice suggestions are more like guidelines. If you are having performance problems with an assembly, then this may not be a great technique to use. However, sometimes there is a price to pay for sophisticated functionality, and if you think that your design can afford the price and will benefit from this functionality, then you should use it.
NOTE
6. Now that everything is in place, click the Make Smart Component tool on the assembly toolbar. If the button is not there, you can add it to the assembly toolbar by selecting Tools ➪ Customize menu, or by selecting Tools ➪ Make Smart Component. The resulting interface is shown in Figure 19.9. 7. In the Smart Component selection box, select the connector part. 8. In the Components selection box, select the two hardware components. 9. In the Features selection box, select the in-context feature from the dummy part. 10. You are now finished setting up the Smart Component. Click the green check mark icon to accept the changes and exit out of the PropertyManager, and save the file.
579
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 580
Creating and Using Libraries
FIGURE 19.9 The Smart Component PropertyManager interface
Creating an auto-sizing Smart Component The simple Smart Component took about 20 minutes to model and set up. That is not too bad for a feature that you will probably use a lot. The benefits are somewhat modest, placing three components and a feature. However, when it comes to the auto-sizing example that is shown next, the benefits are more extensive. A total of seven individual parts are placed (including Toolbox parts) — three of which are automatically sized, depending on the geometry into which the Smart Component is dropped — and an in-context feature is added. To begin, open the part from the CD-ROM named Chapter 19 – Clamp Start. Notice that this is a multibody part. There is no special knowledge that you need to have about multibody parts to complete this task. Multiple bodies are discussed in detail in Chapter 26. 1. With the Clamp Start part open, notice that several configurations already exist. If you click through the configurations or examine the design table in the part, you can see that various dimensions change. The primary dimension that changes is the diameter of the hole, and this change drives the diameter of, and distance between, the mounting holes.
580
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 581
Using Smart Components
NOTE
In SolidWorks 2007, you can only drive auto-sizing by cylindrical geometry.
2. Part of the Smart Component definition includes applying a Mate Reference to the part, so that the big hole automatically snaps to cylindrical geometry. Another aspect is that it adds in-context holes that match the mounting holes on the clamp. Figure 19.10 shows the assembly that this part is meant to go into. The clamp snaps onto the stepped shaft and adds holes to the plate.
FIGURE 19.10 The assembly where the Smart Component will be used
3. Open the file named Chapter 19 Autosize Training Assembly.sldasm. This has been prepared to help you get started with the Smart Component training. The shaft is not necessary in the training assembly. The training assembly is intended to create the in-context Smart Feature and to create the configurator table. The shaft part has been added here for visualization only.
NOTE
4. Insert the clamp part into the assembly, and mate it concentric to the shaft and coincident to the blue plate. It does not matter where the clamp sits along the shaft, but it should be fully mated into the location so that it does not slide back and forth. 5. Edit the plate in the context of the assembly, and convert entities from the mounting holes in the clamp to create holes in the plate that align with the holes in the clamp. 6. Exit the Edit Component mode. 7. Activate Toolbox, select the four holes, as shown in Figure 19.11, and insert Socket Head Cap Screws, 3⁄8 by 24 by 5⁄8 inches. If you do not have Toolbox or choose not to use it, then a part with the correct name and sized configurations is provided on the CD-ROM.
581
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 582
Creating and Using Libraries
FIGURE 19.11 Inserting four screws at once using Toolbox
Pre-select these four edges
8. Use the same fastener to place in the mounting holes, using the correct size for the hole. The length will be set later. Use a default length of 2.25 inches for both mounting holes. Working with the length of the fasteners is not a clean operation in Smart Components. The length is dependent on the thickness of the plate, which is not controlled by the Smart Fastener, nor can the Smart Fastener account for it, except through mates. (Remember that auto-sizing is driven only by a diameter.) Later in this chapter, you will see how the washers and nuts are put in place on the underside of the plate, but the screw length cannot be automatically calculated (unless the screw itself had an in-context relation to the nut).
NOTE
9. Place washers and nuts on the screws on the backside of the plate. 10. This is where the process becomes a little convoluted. When the shaft diameter changes, the hole in the clamp changes to match (within the ranges that will be established). As the clamp becomes bigger, bigger screws are needed to secure the clamp and the holes grow further apart. Bigger screws mean additional configurations for the screw, washer, and nut parts. Remember that the configurations do not necessarily exist. I would not count on a Smart Component working if this meant that Toolbox had to create new configurations.
To create this example, I have pre-populated the Toolbox parts with all of the configurations needed for the range of sizes involved with this Smart Component. When you make your own Smart Components, you will have to do the same thing if you intend to use auto-sizing with Toolbox parts. The difficulty here is that the configurations include the diameter size of the screw as well as the length, which is unknown until you place the part. All you have to worry about in this step is to make sure that the configurations are available and that the screws are placed properly.
582
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 583
Using Smart Components
11. Up to this step, you have just assembled the parts as if this were the only time you were going to do it. The automation of the process comes next. Figure 19.12 shows the training assembly to this point. The shaft and plate are shown in wireframe because they are external to the Smart Component.
FIGURE 19.12 The training assembly up to step 11
12. This is the point in the previous example where the Make Smart Component command was used, and it is no different here. Click the Make Smart Component tool on the assembly toolbar. 13. Figure 19.13 shows the filled in Smart Component PropertyManager. Activate the Smart Component selection box and pick the clamp part.
In the Components selection box, select the six screw instances, the two washers, and the two nuts. In the Features selection box, select the in-context feature or features that are associated with the Smart Component.
583
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 584
Creating and Using Libraries
FIGURE 19.13 The Smart Component Property Manager
Although the in-context feature can affect only a single part, this does not mean that you are limited to a single in-context feature. In most cases, only one feature is needed, but I am sure that there are situations where more than one would be useful. Also, remember that the in-context features are limited to extruded and revolved bosses and cuts, Hole Wizard holes, and simple hole features.
NOTE
14. The configurator table is simply a table that enables you to select which component configurations are to be used with which Smart Component configuration. It looks and works very much like an assembly design table, but it is not Excel-based, and every cell must be set explicitly rather than using techniques for mass population or assigning properties to a range of configs, such as you can do with a real design table.
Each cell has a drop-down list of all of the available configurations for that component. If you have four instances of a single component, then you have to set each instance of each component. Figure 19.14 shows the configurator table for this example.
584
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 585
Using Smart Components
FIGURE 19.14 The configurator table for the Clamp Smart component
If the configurator table were to ever be as easy to use as, for example, an Excel design table, then Smart Component complexity could increase significantly. The configurator table could even ideally be created from an assembly design table. Instead of a single component with its associated hardware and mounting features, think of larger-scale sub-assembly attachments. This sort of work is possible now, but with configurator tables as cumbersome as they are, it is difficult to do more than a handful of parts.
NOTE
15. Click OK. You are now done creating the auto-sizing Smart Component!
File management with Smart Components You may expect that with the training assembly, there is an extra burden of file management with Smart Components. This may seem counter-intuitive, but in fact, the only file that you need to worry about is the Smart Component itself. This is not explained very well (or at all) in any of the documentation, but the Help and every reseller demonstration that I have seen on the topic all recommend that you simply delete the training assembly once you are done with it because it is not needed any more. This seems like saying that you should delete all of the mates in an assembly or the sketch relations in a part. How do you edit the Smart Component if you delete the assembly in which it is created? It turns out that all of the information to recreate the training assembly is stored in the Smart Component itself. This includes the in-context feature (which is stored as a library feature), and the locations of any associated components, as well as the configurator table. Figure 19.15 shows a part of the FeatureManager of a Smart Component. As you can see, the in-context feature, the associated components, and the face references are all listed there.
585
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 586
Creating and Using Libraries
FIGURE 19.15 Part of the FeatureManager of a Smart Component
I was skeptical of this originally and had to test it thoroughly to ensure that deleting the training assembly would not cause any data to be lost, and so I can assure you that it works. Go ahead and delete the assembly.
Editing Smart Components Expanding somewhat on the discussion about whether or not to keep the training assembly file, here is a little exercise that you can try. Make a Smart Component by going through the preceding steps, by using the following tutorial, or by creating one of your own. Just make a simple one with perhaps one associated component and an in-context feature. Then go ahead and delete the training assembly. With the defining assembly gone, there appears to be no way to edit the setup of the Smart Component. RMB click the Smart Feature folder in the FeatureManager of the Smart Component, and select Edit in Defining Assembly, as shown in Figure 19.16. What happens next is that SolidWorks recreates the defining assembly from the data that is stored in the Smart Component. This assembly is saved in a system temp folder using the name <Smart Component name>_ta.sldasm. If the Smart Component uses an in-context feature, it is saved to the temp directory as a library feature file using the name of the dummy part, and appending “_lf” to the filename, for example, Dummy_lf.sldlfp.
586
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 587
Using Smart Components
FIGURE 19.16 Selecting the Edit in Defining Assembly command
The Edit Definition button appears in the upper-right corner of the graphics window. If you click this button, the Smart Component PropertyManager interface appears again, enabling you to change the selection of associated components and in-context features, to change the auto-size setting, or to edit the configurator table. Thus, all of the settings are preserved, and the training assembly exists only as a phantom in a temp directory. Although this appears to be counter-intuitive, it works.
Tutorial: Working with Smart Components This tutorial guides you through creating a Smart Component that only uses the auto-sizing feature. This enables you to manually create parts that snap to size like Toolbox parts, but without using Toolbox functionality. Follow these steps: 1. Open the part from the CD-ROM that has the filename Chapter 19 – Tutorial Start.sldprt. This part originally came from Toolbox, and already contains a few configurations. 2. Make an assembly that contains only this part. 3. Make the part into a Smart Component, and turn on the option to auto-size. 4. Select the small diameter of the part as the concentric mate reference. Figure 19.17 shows the selection.
587
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 588
Creating and Using Libraries
FIGURE 19.17 Selecting the concentric mate reference face
Concentric mate reference face
5. Click the Configurator Table button, and fill the table in so that it looks like Figure 19.18. Some configurations are blank. This is because only the rows that have minimum and maximum values are used by the auto-size function. The rest are overlooked. 6. Close the configurator table, and save the assembly. 7. Exit the assembly and, in the part file, save it to a folder in your Design Library. If you do not know where your Design Library is located, then select Tools ➪ Options ➪ File Locations ➪ Design Library. 8. Display the part in the Design Library panel of the Task pane. 9. Open the part from the CD-ROM with the filename Chapter 19 Tutorial Plate.sldprt. Place this part into a new assembly. 10. Drag the Tutorial Start (Smart Component) from the Design Library into the assembly, and move the part over the holes in the plate. As you drag the part up and down the row of holes, the part changes sizes to match each hole. Figure 19.19 shows all of the holes that are populated with the matching Smart Component sizes, as driven by the configurator table. 11. To edit the configurator table, open the Smart Component part in its own window. Then RMB click the Smart Feature folder and select Open In Defining Assembly.
588
27_080139 ch19.qxp
3/26/07
4:10 PM
Page 589
Using Smart Components
FIGURE 19.18 Filling in the configurator table
FIGURE 19.19 Smart Component parts match holes in the part.
589
19
27_080139 ch19.qxp
Part IV
3/26/07
4:10 PM
Page 590
Creating and Using Libraries
12. An assembly opens that was created from the data stored in the part. Click the Edit Definition button that appears in the upper-right corner of the graphics window. 13. Reassign the minimum and maximum diameter values for the 3⁄16-inch and 1⁄4-inch configurations to the shortest lengths. For example, the chart shows the 3⁄16-32x.75-inch configuration to be assigned to a minimum of .1 and a maximum of .199. Move the .1 and .199 values up two cells to the 3⁄16-32x1⁄4-inch configuration. Do something similar for the 1 ⁄4-28x1-inch configuration. The edited part of the chart now looks like Figure 19.20.
FIGURE 19.20 The edited configurator table
You may have difficulty expanding the width of the column that contains the configuration names, thus making it difficult or impossible to read the ends of the long config names. However, like Excel, you can expand the height of the rows, which causes the config names to wrap, as shown in Figure 19.20.
TIP
Summary Smart Components can automate the placement of a main component, as well as associated mounting features and components. It can also offer automatic resizing options, depending on the geometry to which they are mated. The setup for Smart Components varies from simple to complex, with auto-sizing causing most of the complexity.
590
28_080139 pt05.qxp
3/26/07
4:11 PM
Page 591
Creating Drawings IN THIS PART Chapter 20 Automating Drawings: The Basics Chapter 21 Working with Drawing Views Chapter 22 Using Annotations and Symbols Chapter 23 Dimensioning and Tolerancing Chapter 24 Working with Tables and Drawings Chapter 25 Using Layers, Line Fonts, and Colors
28_080139 pt05.qxp
3/26/07
4:11 PM
Page 592
29_080139 ch20.qxp
3/26/07
4:11 PM
Page 593
Automating Drawings: The Basics
E
ngineering drawings include a lot of repetitious information from one drawing to the next. The information is not always exactly the same, but it is usually in the same format and of the same type. For example, part drawings always include information about who made the drawing, when they made it, what the material and surface finish of the part are, and some basic notes that depend on the use of the drawing (manufacturing, assembly, or inspection). All of this information needs to appear consistently on each drawing, every time. However, humans are not always good at following dull routines, which is why we have computers, to help with these boring or difficult tasks.
The Difference between Templates and Formats Even experienced users sometimes cannot tell the difference between templates and formats in SolidWorks. I have mentioned this before, but it is worth mentioning again. Simply put, templates are collections of documentspecific settings and default views, saved in the *.prtdot (part template), *.asmdot (assembly template), and *.drwdot (drawing template) formats. Formats, more formally called “sheet formats,” are exclusive to drawing documents, and contain the sheet size, the drawing border-line geometry, and the text/custom property definitions that go with the text in the drawing border. Formats can also include company logo images.
593
IN THIS CHAPTER The difference between templates and formats Creating drawing formats Creating drawing templates Creating blocks
29_080139 ch20.qxp
Part V
3/26/07
4:11 PM
Page 594
Creating Drawings
You can save formats in templates; in fact, this is the method that I both use and recommend. Using SolidWorks’ default settings, you specify the size and the format when creating a new drawing from a blank template; however, when the format is already in the template, the size is taken care of ahead of time, and so the templates end up being saved as sizes. Of course, you can change formats later if you need to use a larger drawing sheet.
Can templates be changed? No. This is one of the most common questions from new users. Perhaps if SolidWorks received enough enhancement requests on this topic, they would be willing to change the software to enable the user to transfer the settings from an existing template to one or more existing documents. Currently, once you create any kind of a document, you cannot change the underlying template. However, you can change all of the settings, which is for the most part equivalent. There are macros available on the Web that you can use to copy the settings from one document to another or to apply settings to a document or group of documents. In particular, there is a spreadsheet available that has a list of settings and options that you can copy to a given document. You will need to search around for these utilities, but they should be easy to find through the newsgroup comp.cad.solidworks, by using Google Groups if you do not have a newsreader.
Why have different templates or formats? Different formats must be maintained for different sheet sizes. If you do contract design or detailing work, then you may need to maintain separate formats for different customers. Some people also choose to have different formats for the first sheet of a drawing and a simplified format for the remaining sheets. Why you should maintain different templates is an easier answer. First, if you put formats on the templates, then you are making separate templates for various sizes. Also, separate templates are frequently created for different units or standards, because templates contain document-specific settings. I also keep a blank template with no format on it just to do conceptual scribbles or to make an informal, scalable, and printable drawing without the baggage that typically accompanies drawings. SolidWorks can install with default document templates that use different standards. Be careful of the difference between drawings with ANSI and ISO standards, or more importantly, the use of third-angle projection versus first-angle projection. Figure 20.1 shows the difference between a third- and first-angle projection. Third angle is part of the ANSI standard used in the United States, while first angle is part of the ISO standard used in Europe.
CAUTION
If you work for a company that does a lot of international work, then you may have to deal this issue more frequently. The setting that controls the projection angle is not in Tools, Options (where you might expect it to be), but in the Sheet Properties, which you can access by RMB clicking anywhere on the blank drawing sheet and selecting Properties.
594
29_080139 ch20.qxp
3/26/07
4:11 PM
Page 595
Automating Drawings: The Basics
FIGURE 20.1 Third-angle versus first-angle projection
Creating Drawing Formats Drawing formats can be either simple or difficult; the good news is that you can choose which one you want to use.
Customizing an existing format The simple solution is to customize an existing format for your own use. This generally works well, and you can usually finish the task in a few minutes, depending on your requirements. Some options exist for sources. The easiest option is to take the existing SolidWorks sample formats and add a few things such as a company name, logo, and tolerance block to them. You can also use formats from other drawings, editing and saving out as your own.
Sample formats The sample formats that installed with SolidWorks are located in the Data folder in your SolidWorks installation directory. They include ANSI sizes A to E, and ISO sizes A0 to A4. You can probably find enough space on the formats to place a company logo and some standard notes. You cannot open a format directly — it must be on a drawing — and so to get a closer look at the format, you must make a new drawing using the format. Templates that have been saved with a format already on them skip the step of prompting you to select a format, which allows you to create drawings quickly. If you select one of the default SolidWorks templates, these do not have formats on them and so you are prompted to select one. Figure 20.2 shows the interface for selecting a format that displays after you have selected the template for a drawing.
NOTE
595
20
29_080139 ch20.qxp
Part V
3/26/07
4:11 PM
Page 596
Creating Drawings
FIGURE 20.2 Selecting a format
Editing a format The SolidWorks drawing environment frequently gives new users trouble. Once you understand how it is organized, it is not so bad, but you may make several mistakes while getting used to it. In the drawing, you are either editing the sheet or editing the format. You can think of the sheet as being a piece of transparent Mylar over the top of the drawing border format. In order to get to the format, you have to peel back the Mylar layer. Drawing views go onto the sheet, and so when you edit the format, any drawing views that may be there disappear. (Of course, drawing views — except for maybe some Predefined views — should not be on a drawing when you are creating a format.) To peel back the sheet and gain access to the format, RMB click a blank area of the sheet and select Edit Sheet Format. This RMB menu is shown in Figure 20.3. Be careful of the terms here, which include Sheet and Sheet Format. The sketch lines of the format light up like a sketch becoming active, and at the lower right-hand corner, on the status bar, a message appears, saying Editing Sheet Format. The lines in the format border are just like regular SolidWorks sketch entities, but they display a little differently. Also, sketch relations are sometimes not used in formats because solving the relations causes the software to be a bit sluggish. Typically, Trim and Extend functions are the best tools for editing lines. Images that you add to the format work best as bitmaps. Be aware of the file size of the bitmap when you put it into the format, as bitmap images can be large, and all of that extra information will travel around with each drawing that you create from the format. Figure 20.4 shows a bitmap placed in the format. You can resize the bitmap by dragging the handles in the corners, and move it by simply dragging it. The image to the right in Figure 20.4 shows the Print Preview window. I included it here to show that the outline around the bitmap that displays while you are working in SolidWorks does not print out.
596
29_080139 ch20.qxp
3/26/07
4:11 PM
Page 597
Automating Drawings: The Basics
FIGURE 20.3 Selecting the edit sheet format
FIGURE 20.4 Placing an image
597
20
29_080139 ch20.qxp
Part V
3/26/07
4:11 PM
Page 598
Creating Drawings
Managing text One of the newer functions in SolidWorks is the ability to make a text box of a specific size that causes text to wrap. This is particularly useful in drawings. The image in the center of Figure 20.5 shows a new annotation being added. The image to the right shows the same text box after the corner has been dragged.
FIGURE 20.5 Adding an annotation, and wrapping the text
When dragging the text box, it may seem intuitive to drag the middle handle on the end, thinking that shortening the box will cause it to wrap. However, that only works if the box has some space on the bottom to wrap to; SolidWorks does not automatically expand the text box down the way PowerPoint does. You are better off dragging a corner to get the wrap to work.
TIP
Custom properties The most important part of the drawing format is the custom properties. While the rest of the format is just for display, custom properties use automation to fill out the title block automatically from matching custom properties in the model document. Custom properties can pull items such as filenames, descriptions, materials, and other properties from the model associated with the sheet, or they can pull data from the drawing itself, such as the sheet scale, filename, sheet number, and total sheets. Figure 20.6 shows the existing custom property formatting in the default format being used for this example.
FIGURE 20.6 Custom property formatting in the title block
598
29_080139 ch20.qxp
3/26/07
4:11 PM
Page 599
Automating Drawings: The Basics
Property link display The syntax $PRP or $PRPSHEET indicates that the property that follows the syntax is to be pulled from either the current document (drawing) or from the model specified in the Sheet Properties, respectively. This is an important distinction to make. Most of the time, custom properties are typed in at the part or assembly level so that the data can be reused by drawing properties, BOM, or even design tables. Notice that all of the notes in the format that are showing raw syntax are pulling data from the model. This is because there are no properties being pulled from the drawing, “Draw2,” and the Scale notes are driven by the drawing. When no value exists for the property to display, you have an option of what to show. Figure 20.7 in the image to the left shows the settings in the View menu that control the display of syntax of the custom property links. In general, it is common to turn off the error display, and to show the link variables.
FIGURE 20.7 Link variable display options and effects
Errors and link variables The errors in Figure 20.7 are caused by links to the local document for which there is no corresponding property. For example, the “ERROR!: COMPANYNAME” message is linked to “$PRP: COMPANYNAME,” but the local custom property “COMPANYNAME” does not exist. If it existed, but had a null or space value, the error would disappear. Likewise, with the option to display link variables turned on, the syntax that calls model custom properties displays until there is some value for it to pull from. If a part is put onto the drawing, then some of the properties are filled in because properties and values exist to pull from, and the rest of the properties simply disappear to make space. Notice in Figure 20.8 that the Material property has been filled in, but the Finish property has not. This is because there is either no Finish property in the part on the drawing or a null value in the Finish property.
599
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 600
Creating Drawings
FIGURE 20.8 Custom properties filled in by a part
When initially setting up the format, it can be useful to have a dummy model already on the drawing. You should delete the views containing the dummy model before saving the format or the template. The dummy model should have all of the custom properties in it that you intend to use in your drawings. This prevents the blank fields or error messages during setup.
TIP
If you drag-and-drop a part onto a drawing while editing in the Sheet Format, the views may appear for a split second and then disappear again. This is because you cannot display drawing views while editing the Sheet Format. Once you exit the Sheet Format and go back to editing the sheet, the views can display once more.
NOTE
Creating linked properties It is easy to create annotations that are linked to properties. Begin as if you are creating a note: 1. Click the Note toolbar button on the Annotations toolbar, or click Insert ➪ Annotations ➪ Note. 2. Place the note on the drawing. The Formatting toolbar appears. 3. Click the Link To Property button in the Text Format pane of the Note PropertyManager. This displays the Link to Property dialog box, as shown in Figure 20.9, which gives you the option of linking to a custom property in the current (drawing) document or in the model (part or assembly) that is on the drawing. 4. If the desired custom property is not in the drop-down list shown to the right, then you can type it into the text box or click the File Properties button to edit the properties. This button is not available for the model if there is no model on the drawing, in which case you must type in the name of the property manually.
600
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 601
Automating Drawings: The Basics
FIGURE 20.9 The Link to Property dialog box
Creating a format from a blank screen There is no graceful way to say this, and so I’ll just say it: SolidWorks is not really good at manipulating a lot of 2D sketch-line data such as what you find in drawing title blocks. I have gone through the process of making my own formats, as well as the process of importing data from which to create one. By the time you have everything centered, in the right color, and on layers if you are using them, and the text aligned, you have used up more than a couple of hours. If you choose to custom build one size and then use it to create the rest of the sizes, you need to be patient. SolidWorks typically turns off the most useful parametric sketch functions when working with a format (what SolidWorks considers a large sketch) because of speed problems. If you would like to turn these settings back on, they are located at Tools ➪ Sketch Settings. SolidWorks is not the best program for making a nice-looking drawing border. If you insist on creating your own, set aside some time for it, and have an idea of what you are trying to achieve, maybe sketched out by hand or in a printout of a title block that you would like to replicate. The Modify Sketch tool may be useful in moving entities around the screen, and even scaling them. You can also access a useful hidden command by RMB clicking the name of the drawing in the FeatureManager, and selecting Move from the menu, as shown in Figure 20.10. A small dialog box appears that enables you to move the entire format by a specified distance. If you need to use construction geometry to help you size or locate objects or text while manually creating your Sheet Format, then you do not need to delete the geometry when you are done. You can put all of the construction geometry on a specially created drawing layer and turn the layer off.
TIP
601
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 602
Creating Drawings
FIGURE 20.10 The Move Drawing dialog box
Creating a format from an imported DWG/DXF file If you still think you want to create your format from an imported DWG or DXF file, then locate the file that you would like to import, and open it from the File, Open dialog box. The DXF/DWG Import screen appears, as shown in Figure 20.11.
FIGURE 20.11 The DXF/DWG Import screen
The sample file used for this example can be found on the CD-ROM for Chapter 20 if you are interested in following along. To make a drawing format, you can select the Create New SolidWorks Drawing and Convert To SolidWorks Entities options. Although one of the other options contains the word format, it is not being used in the same sense, so do not be misled. When this selection is complete, click Next. Figure 20.12 shows the next screen.
602
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 603
Automating Drawings: The Basics
FIGURE 20.12 The Drawing Layer Mapping screen
Select the Layers Selected For Sheet Format option. Select the TB layer, leaving the other layers off. Every imported file will be different in this respect, because layers used by title blocks vary widely. Click Next when you have made these selections. Figure 20.13 shows the Document Settings screen.
FIGURE 20.13 The Document Settings screen
603
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 604
Creating Drawings
The important features in the Document Settings screen are the Document template selection and the Geometry positioning options. Document template selection is only important if you plan to save the format with a template. Be sure to select a template that does not already have a format saved in it. In the Geometry positioning section, if you can get the software to center the title block for you, definitely take advantage of this functionality and use the Center In Sheet option. Once you are happy with these settings, click Finish. The resulting format is shown in Figure 20.14.
FIGURE 20.14 The finished imported format
From here, you can add the links to custom properties as described earlier, as well as logo images, loading favorites, and blocks. You can now save the format as described in the next section. Using the Color Display Mode button on the Line Format toolbar toggles the display from using the layer color to using the SolidWorks sketch colors. Another setting that affects sketch display in drawings is found at Tools ➪ Options ➪ System Options ➪ Drawings ➪ Display Sketch Entity Points, which shows endpoints and arc center points in the same way that they are shown in feature sketches.
TIP
604
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 605
Automating Drawings: The Basics
Saving the format You can save drawing formats in two ways, either with the template, or separate from the template. You cannot edit formats separate from a template, but they do have their own file type, *.slddrt. If you are wondering how the extension *.slddrt relates to a sheet format, what is now known as sheet format used to be called a drawing template (thus, the drt of slddrt). What is now called a template did not exist in 1997. The shift in architecture and, more importantly for users, the shift in terminology has left many people a bit confused.
NOTE
Saving templates is covered in the next section. To save a format, select File ➪ Save Sheet Format. This can be done with or without the format being active. Save the format into a location with other formats, and give it a descriptive but unique name. If you have not yet done so, this is a good opportunity to create a separate folder, outside of your SolidWorks installation folder, that contains your most frequently used files. Remember also to tell SolidWorks where this library location is through Tools ➪ Options ➪ System Options ➪ File Locations ➪ Sheet Formats.
Second sheet formats When you have multi-sheet drawings, it is often important to have a simplified or specialized format for the second sheet. Figure 20.15 shows sample page-one and page-two formats side by side.
FIGURE 20.15 First and second sheet formats
Adding new sheets You can add sheets to a drawing through the RMB menu of the sheet tab at the lower-left corner of the drawing window. If you RMB click the first sheet tab, the sheet that is added gets the format that is used on the first sheet. If you RMB click the second sheet tab, the added sheet gets the second sheet format.
Reloading formats If a format has been changed, and you would like to update a drawing to the new format, this option is available in the Sheet Properties, as shown in Figure 20.16.
605
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 606
Creating Drawings
FIGURE 20.16 Updating a format through the Sheet Properties
Creating Drawing Templates Document-specific settings are an important part of the template, and it is probably best to get one size drawing completely set up the way you want it, and then create the other sizes from this drawing. This helps to ensure that the settings, such as bent leader length, font, and line weight, are the same for all of the templates. Uniform settings on drawings give them a consistent look, and make them easier to read. An in-depth discussion of document-specific settings at Tools ➪ Options ➪ Document Properties can be found in Appendix B.
Using predefined views in drawing templates When I use drawing templates, one of my favorite techniques to get to a multi-view drawing quickly is to put one Predefined view on the template along with appropriate views projected from the Predefined view. A Predefined view establishes an orientation and location on the drawing sheet. You can add multiple Predefined views and align them with one another on the drawing sheet so that a drawing is automatically populated by the model, but this is not recommended because if you decide to change the orientation of the drawing, you have to change each Predefined view independently. If you set up a single Predefined view and make the rest of the views with projected views, changing the orientation of the Predefined view causes all of the projected views to update associatively. You cannot directly change the orientation of a projected view. Predefined views and views projected from Predefined views appear blank until they are populated with model geometry. The predefined part of a Predefined view is the orientation and placement of the view.
606
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 607
Automating Drawings: The Basics
Figure 20.17 shows a template using Predefined and projected views. You can access Predefined views on the Drawings toolbar; although it is not there by default, you can place it on the toolbar through the Tools ➪ Customize ➪ Commands interface. You can also access Predefined views through Insert ➪ Drawing Views ➪ Predefined. Projected views are also accessed from the Drawings toolbar.
FIGURE 20.17 Predefined views on a template
Once a Predefined view has been placed, you can select an orientation for it from the PropertyManager. Figure 20.18 shows the Drawing View PropertyManager. The orientation for a view is set in the top Orientation panel. In addition to orthogonal views, you can also create isometric and other custom views as Predefined views. Once the view has been oriented, you may want to create more views on the drawing that also become populated by model geometry. This is where the projected views are used. Make sure that the drawing properties are set to the correct projection angle. Because the rest of the views have been created relative to the Front view, none of the views needs to be rotated as they would if, for example, the Top view were placed above the Back or Right views.
607
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 608
Creating Drawings
FIGURE 20.18 The Drawing View PropertyManager
Although it is not on this drawing, many drawing templates include a third-angle projection symbol as a part of the Title Block, which is in the format. Figure 20.19 shows first- and third-angle projection symbols. These are included as blocks with the sample data in the SolidWorks 2007 installation. Blocks are discussed in more detail in Chapter 22.
FIGURE 20.19 Projection angle symbol blocks
608
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 609
Automating Drawings: The Basics
Aligning predefined views You can align views to one another through a view’s RMB menu, as shown in Figure 20.20. Projected views are aligned to one another automatically, but if you chose to use a Predefined view rather than a projected view to one side of the original Predefined view, you can use the Align Vertical by Origin or the Align Horizontal by Origin command. This ensures that the parts in each view are aligned. Aligning by center should not be used for projected views on an engineering drawing, because it is not guaranteed to line up edges in adjacent views.
FIGURE 20.20 Alignment options
Populating a drawing with Predefined views Four methods exist to populate a drawing with Predefined views: n Drag-and-drop: Drag a part or assembly from the FeatureManager and drop it in the drawing window. All Predefined views are automatically populated. n Insert Model: RMB click a view and select Insert Model. From the interface, browse for the model to be displayed in all of the related (projected) views. n PropertyManager: Select a predefined view, and from the PropertyManager, select Browse in the Insert Model panel. n Make Drawing from Part/Assembly: Click the Make Drawing From Part/Assembly button in the Standard toolbar and select a template that uses Predefined views.
609
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 610
Creating Drawings
Predefined views and sheet scale When Predefined views are created, they are set to follow the sheet scale by default; however, you can manually set them to have a custom scale. If you are using the automatic scaling option (found at Tools ➪ Options ➪ System Options ➪ Drawings ➪ Automatically Scale New Drawing Views), the sheet scale is automatically changed when the drawing views are populated to make a nice fit of the model geometry on the drawing. The scales used by the automatic feature are all standard multiples of two, and so you do not have to worry about odd scale factors on your drawings.
Predefined view limitations The function and expectations of Predefined views are fairly straightforward, although there are a few things that could be improved. For example, SolidWorks does not allow you to create predefined section or detail views. Also, the View Palette does not preview the populated Predefined views.
Using favorites and blocks in templates Favorites function like styles and formatting in Microsoft Word, or other word-processing software, by adding underlines, bold formatting, and even items such as tolerances and symbols. Hole Wizard Favorites are described in Chapter 17, and work similarly to Dimension and Note Favorites (described in Chapter 22). This chapter is concerned with the fact that favorites can be saved to files, and loaded to documents. In particular, they can be loaded to documents that can be saved as templates, thus maintaining the loaded favorites. Several types of favorites can be loaded into and saved with drawing templates, including dimension, note, GD&T, weld, and surface finish symbols. When a favorite is loaded into a template, any document that you create from that template can use any of the loaded favorites. The many file types for favorites exist mainly to transfer favorites from one document to another, but they are not needed once the favorite is loaded. As a result, before saving a template, you should gather together your favorites into your library folder and load them into the template. You can load favorites by going to the interface for the type of favorite, for example, dimensions or notes. Figure 20.21 shows the top of the Note PropertyManager interface, which contains the Favorites panel.
FIGURE 20.21 The Favorites panel for the Note PropertyManager
610
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 611
Automating Drawings: The Basics
The buttons in the Favorites panel of the Note PropertyManager interface have the following functions: Apply the default attributes to the selected notes Add or update a favorite Delete a favorite Save a favorite Load a favorite This section is concerned with the last function, Load a favorite. After clicking this button, you can load multiple favorites at once by Shift-selecting them through the Open dialog box that appears. Even symbol types that can be applied by dragging-and-dropping from the Design Library can also be loaded as favorites. However, I prefer dragging from the Design Library because you get a preview of the symbol; with the favorites, you just see a text tag. Blocks can also be loaded into a template or used from the Design Library as drag-and-drop items.
Custom properties in templates Part of the usefulness of templates is that you can do work once, and have it replicated many times. This is an excellent example of process automation. One of the ways that you can take advantage of this feature is by putting default custom properties in your templates. In many cases, simply having a default value for something is better than no value, and a default value may even prompt you to put a value with real significance in the property. For example, the Description of a document is extremely important, especially if you are using sequential part numbers for your filenames. A custom property named Description can be added to your template, and the default value is used unless it is changed when the template is used in a document. You have already seen how custom properties used in parts can be instrumental in filling out a title block on a drawing. Custom properties in part and assembly documents work exactly the same as they do in drawings. The custom properties interface is shown in Figure 20.22.
611
20
29_080139 ch20.qxp
Part V
3/26/07
4:12 PM
Page 612
Creating Drawings
FIGURE 20.22 The custom properties Interface
Saving a template Drawing templates are saved through the Save As menu, by selecting Drawing Templates in the Files of Type drop-down list. This automatically takes you to the folder for the templates, as specified in Tools ➪ Options ➪ File Locations ➪ Templates. In the case where a template and format have been saved together and are being saved together, but the format also needs to be saved to its own file, saving the template with the changed format only changes the format for documents that are made from that point forward with that template. You may also save out the format to its own file from the edited template. Formats are needed in their own file (in addition to existing within a template) for situations when you have an existing drawing and want to change the size of the sheet, and then need a format to put on the sheet. Another situation is when a drawing may come in to your organization from an outside contractor, and they have not used your format; in this case, you can simply replace their format with yours, or you can send them your format (and template, for that matter), from which the contractor can create all drawings for you. Separate formats are important for when you have multi-sheet drawings. When adding a sheet, you also need to add a format. You can save multi-sheet drawing templates in which the first and second sheets have different formats on them.
612
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 613
Automating Drawings: The Basics
Creating Blocks Blocks are an important aspect of automating drawing creation. They enable you to combine text and sketch geometry and to annotate common features on drawings. Blocks are discussed in Chapter 4 (sketch blocks) and also in Chapter 22 (creation, editing, and placement). Blocks can be used for many purposes, including the following: n Tolerance blocks on drawings that might change with the process (if you do not have separate formats that already contain this information). n Electrical or pneumatic schematic symbols that can be snapped together. n Flowchart type symbols. n Fluid flow-direction arrows. n Special markers calling attention to a specific detail. n Sheet formats that can be created as a block, enabling you to move it around as a single entity much more easily. You can create blocks by selecting a group of sketch entities, annotations, or symbols and then clicking Tools ➪ Block ➪ Make.
CROSS-REF
For more information on the creation, editing, management, and placement of blocks, see Chapter 22.
Summary Getting your templates and formats correct creates an excellent opportunity to save some time with drawings by automating many of the common tasks through the use of templates, Predefined views, multiple formats, blocks, favorites, and linked custom properties. Setup becomes more important when you are administering a larger installation, but is also important if it is just for yourself. One of the most important things that you can do is to establish a file library and direct your Tools ➪ Options ➪ File Locations paths to the files. There is nothing quite as productive as having something that works right the first time, and every time.
613
20
29_080139 ch20.qxp
3/26/07
4:12 PM
Page 614
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 615
Working with Drawing Views
T
en years ago, when I first moved from AutoCAD to SolidWorks, one of the most difficult concepts to understand was that in SolidWorks you do not create lines in the drawing view, and in fact, you cannot move any of the lines in the view at all. The drawing view was in effect a snapshot of the 3D model from a particular point of view. The snapshot could be updated, but it could not be manipulated manually. At first, this seemed a little bit confining. However, once I understood it, the concept was liberating rather than confining. It meant that I did not have to worry about the drawing views being inconsistent or incorrect. All I had to worry about was the 3D model being correct. If you are a new user, then you should feel confident that SolidWorks properly maintains the views better than you could do it manually. Any type of view from any point of view of even the most complex model or assembly geometry can be updated perfectly. To be fair, there are some things that SolidWorks has difficulties with, but knowing this now means that you will be ready for these issues and know how to deal with them when or if they occur. One issue arises from assemblies that contain parts that interfere. HLR (hidden line removed) display of interfering parts can show extra lines or hide lines that should be shown. At other times, you may have issues with lightweight parts. When possible, it is best to work with model geometry that is fully resolved as well as highquality drawing views.
615
IN THIS CHAPTER Creating common view types Creating other view types Using display options in views Distinguishing views from sheets Tutorial: Working with view types, settings, and options
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 616
Creating Drawings
Creating Common View Types The previous chapter discussed Predefined views in templates. Predefined views make it faster to automatically create drawings with consistently placed, simple views. However, sometimes you may need to create views on templates that do not have Predefined views, or you may need a special arrangement of views. SolidWorks has a good assortment of view types to make practically any type of view that you may need. When creating or changing either the geometry or the settings that control how a view is displayed, the view may become cross-hatched, indicating that the model needs to be rebuilt. To resolve this problem press Ctrl+Q, to update the view.
NOTE
Using the View palette The View palette is shown in Figure 21.1. It is activated automatically if you use the Make Drawing From Part tool, unless the drawing template that you select has Predefined views on it. In this case, the Predefined views are populated, and the View palette is not activated.
FIGURE 21.1 The View palette
616
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 617
Working with Drawing Views
The View palette contains all of the standard named views, the current view of the model, and any annotation views (views that the model was in when annotations were added to it). You can dragand-drop these views on the drawing. To activate the View palette without using the Make Drawing From Part tool, simply create a new drawing document, ensure that the Task Manager panel is available, and click the View Palette tab in the Task Manager. Then use the ellipse button (. . .) to browse to a part. After you select a part, the palette window is populated with views of the model. This method has the advantage of enabling you to see the views before you put them down. It does not link views in the same way that the Predefined and projected views are linked, however. I find this interface somewhat difficult to use, and prefer to set up the Predefined views or to use the Multiple Views option in the Model Views PropertyManager, which is shown later in this chapter.
Named Named views are one of the few types of views that are not dependent on another view. Everything has to start from somewhere, and most drawings have to start with either a named or Predefined view. You can place named views by using the Model View button on the Drawings toolbar or by clicking Insert, Drawing View, Model. Using the Model View PropertyManager is a two-step process, and is shown in Figure 21.2. In the first step, you select the model, and in the second step, you set the options for the view.
Open documents The large selection box in the Part/Assembly to Insert panel displays any models that are open in SolidWorks at the moment. If the model that you are looking for is not in the list, then you can use the Browse button to look for it. I find this part of the interface to be clumsy because an extra step is involved that was not there before. It used to be that when you chose to place a named view, you would open the Browse dialog box directly, but now there is an intermediate step. For this reason, I try to use a workflow that avoids this dialog box. I typically use the Create Drawing From This Part/Assembly if the part is open, and if not, I drag-and-drop the part onto a new drawing template with Predefined views on it. This combination saves a lot of work. One of the annoying quirks of this interface occurs in the first step when you are using the PropertyManager (the image to the left in Figure 21.2). If you click in the drawing window for some reason (for example, if you are expecting it to simply place a view), then a prompt appears, stating that you are not paying attention. (Obviously this happens to me very frequently.)
Thumbnail Preview This is a nice option that shows the part that you selected in the Open Documents window. It is a useful feature, but, because it is collapsed by default, it is easy to miss. After it is used the first time, it retains the setting.
617
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 618
Creating Drawings
FIGURE 21.2 The Model View PropertyManager
Options This should just say “Option,” as there is only one. In any case, the Start Command When Creating New Drawing option causes this PropertyManager to open up immediately when a new drawing is created. If you click in the drawing window, then the prompt appears, telling you that you are not paying attention.
618
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 619
Working with Drawing Views
Cosmetic Thread Display Cosmetic threads can display in either high or draft quality. The distinction is made for performance reasons. The difference in terms of display is that in high-quality mode, hidden cosmetic threads (cosmetic threads that are behind a face) do not display in shaded mode.
Number of Views and Orientation This is the one function that almost redeems the Model View PropertyManager for me. In Single View mode, you select the view that you want to place from the Orientation panel, place the view, and then move on. In Multiple Views mode, you select all views that you want to be displayed, including choices such as Current Model View and any named views that are created in the model interface. These views are indicated on the drawing as boxes (representing view borders), as shown in Figure 21.3.
FIGURE 21.3 Placing multiple views
This is really useful functionality. It makes view selection and placement very easy and is visually clear. Unfortunately, the Single View setting is the default setting, and the PropertyManager does not remember the last setting that was used. Still, the combination of Multiple Views and Orientation is far better, in my opinion, than the View Palette, which I find visually confusing and non-intuitive.
Options The one option in the Options panel is Auto-Start Projected View, which, on the placement of a view, automatically enables you to place more views. This option only works when you have selected the Single View option in the Number of Views panel.
619
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 620
Creating Drawings
Display Style You can set the default display style in Tools ➪ Options ➪ System Options ➪ Drawings ➪ Display Style. This panel provides an override for views being placed. This panel also allows you to control High or Draft Quality views, which are described later in this chapter.
Scale SolidWorks drawings always default to showing views at the overall sheet scale, unless the System Option on the Drawings page called Automatically Scale New Drawing Views is turned on. If this setting is on, the sheet scale saved with the drawing template is overridden. For example, a 1:1 sheet scale can be changed automatically to 1:4 by the setting. You can change the sheet scale through the sheet properties, which were discussed in Chapter 20. Controlling views with the sheet scale makes it much easier to change the size of a drawing and to scale all of the views together. Individual views can be displayed at the view scale, and detail views are typically created at a different scale automatically. The scale setting is found at Tools ➪ Options ➪ System Options ➪ Drawings ➪ Detail View Scaling. Detail views, covered later in this chapter, automatically get a note showing the custom scale for the view. You can create a note that functions in the same way as the automatically created “Scale” text manually from a note and a link to a custom property for views where the link to the sheet scale has been broken manually.
TIP
A note that automatically links to the scale of a drawing view is something you could consider creating a note favorite or block for.
Dimension Type Even in non-orthogonal (isometric) views, true dimensions should be used for most drawing views. Projected dimensions depend on the angle of the edge to the view plane.
Cosmetic Thread Display If something is worth having, it is worth having twice. This panel appears in both steps, just in case you missed it in the first step.
Projected view The Projected view type simply makes a view that is projected in the direction that you dragged the cursor from the selected view. Be aware that first-angle and third-angle projections result in views that are opposite from one another. For example, if you drag at a 45-degree angle, the result is an isometric view. When placing an isometric view that you have created in this way, SolidWorks constrains the new view to a 45-degree-angle line through the Origins of the two views. To place the view somewhere other than along this line, press the Ctrl key while placing the view to break the alignment. The PropertyManager for the Projected view is shown in Figure 21.4. When you use the push-pin on the Projected View PropertyManager, you can place multiple projected views from the originally selected view, or select a new view to project views from. Display properties and scale of the projected views are taken from the parent view.
620
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 621
Working with Drawing Views
FIGURE 21.4 The Projected View PropertyManager
Standard 3 view The Standard 3 View tool on the Drawings toolbar can also be accessed at Insert ➪ Drawing View ➪ Standard 3 View. This places a Front view, and projects Top and Right views for thirdangle projection drawings.
Detail view The Detail view is activated from the Drawings toolbar or at Insert ➪ Drawing View ➪ Detail. Either way, you can use the function in two different ways, one that is fast and easy and the other that gives you more control but is not quite as fast.
Pre-drawn detail circle The detail “circle” can be drawn before you initiate the Detail View command. When you pre-draw a detail circle, you must ensure that you are sketching in the view and not on the sheet. To draw in the view, the view must be activated. You can activate a view by clicking in the view or by bringing a sketch cursor over the view. When you activate a view, the status bar in the lower-right corner of the SolidWorks window displays the message, “Editing Drawing View,” as shown in Figure 21.5. The dotted border in the image to the left shows that the view is selected, and the status bar shows that it is activated. The image to the right with the solid corners indicates that the view has “Locked Focus.” You can lock focus on a drawing view by double-clicking it or by right-clicking and selecting Lock Focus from the menu. If a view is not activated or the focus is not locked on the view, then any sketch elements that you draw will be placed on the drawing sheet. While sketching in a drawing view, it is a good practice to watch the status bar. The point of all of this is to sketch a closed loop in the view so that it can be used for a Detail view. The closed loop can be a circle, ellipse, spline, series of lines, or any other shape, as long as it is a closed loop. The closed loop is called a circle for the purposes of the Detail view in SolidWorks terminology.
621
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 622
Creating Drawings
FIGURE 21.5 Activated drawing views
A setting controls how the circle displays, in particular whether it displays as drawn or as an actual circle. This setting is found at Tools ➪ Options ➪ System Options ➪ Drawings ➪ Display New Detail Circles as Circles. The name of this setting sounds strange — after all, what else would you call a circle? If the setting is turned on, regardless of what closed-loop shape you draw, it will display as a circle. If the setting is off, then SolidWorks will display whatever shape you draw. The different results are shown in Figure 21.6.
FIGURE 21.6 Drawing a closed loop, with the Display Detail Circles as Circles option both on and off
Display Detail Circles as Circles turned on
622
Display Detail Circles as Circles turned off
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 623
Working with Drawing Views
Once you create the loop, you can click the Detail View toolbar button and place the view. The view is automatically scaled by the factor set at Tools ➪ Options ➪ Drawings ➪ Detail View Scaling.
Detail circle drawn in-line A faster way to complete the Detail view is to simply click the Detail View toolbar button without pre-selecting or pre-drawing the loop. This activates the Circle sketch tool immediately, which activates the view as soon as you bring the cursor over the view, so that when you draw the circle, it is sure to be in the view rather than on the sheet. Alternatively, you could swap the circle tool for an ellipse or spline; this works just as well, but offers more flexibility. Regardless of the sketch tool, when you close the loop, SolidWorks prompts you to place the view. The workflow for this in-line method is better than the old-school predrawn loop technique.
Editing a Detail view You can edit a Detail view by dragging the circumference of the detail circle to a new diameter, dragging the center of the detail circle to a new location, or by selecting Edit Sketch from the detail circle RMB menu. This method enables you to edit sketch relations or otherwise edit the sketch that you used for the detail. When you are done with the sketch, you can use the Confirmation Corner to click OK. You can delete Detail views by selecting and deleting the detail circle. Unlike older versions of SolidWorks, in SolidWorks 2007, deleting the detail circle gives you the option to delete the resulting view as well as the original sketch. Also, deleting the detail view gives you the option to delete the detail circle and the original sketch.
Section view Section views in SolidWorks offer many options.
Default Section view The default Section view has the same in-line and pre-drawn optional techniques as the Detail view, as well as the same advantages and disadvantages. Section views have the possibly unique distinction that they often use a straight line, and that straight line often goes through the center of a cylindrical feature. Even though you are in a drawing and not in a model sketch, you may still benefit from model sketching techniques. For example, to draw a straight vertical line through the model shown in Figure 21.7, in the images on the
623
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 624
Creating Drawings
left, you can hover the cursor over a circular edge to wake up the center, and then pick up the inference lines to the center. Another technique is to show the temporary axes (using the View menu), just sketch the line, and then assign a sketch relation in the same way that you would in a feature sketch. This technique is shown in the images on the right.
FIGURE 21.7 Aligning a line in a Section view sketch
You can also use jogged section lines with the default section tool. Similar sketch relation techniques are more common in jogged sections because there are more sketched lines. The results are shown in Figure 21.8.
624
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 625
Working with Drawing Views
FIGURE 21.8 Default and jogged Section views
Partial Section view A Partial Section view is created when the section line does not cut all the way across the model. In Figure 21.9, the line that is drawn to create the Partial Section view was the vertical section line. The prompt that appears enables you to confirm that you intended to create a partial section cut. If you answer No to the prompt, the result is an error, with the new view displayed in the dangling color.
625
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 626
Creating Drawings
FIGURE 21.9 A Partial Section view
Sketched line
You can use another technique to create a section that looks like a partial section, but is not considered a partial section by SolidWorks. You can create it by drawing perpendicular lines, and selecting the line to be used as the projection direction for the section before clicking the Section View tool. This differs from a true partial section in that it shows half of the model unsectioned. It is also similar to the Aligned Section view, but it does not unfold the second sectioned side. When the prompt shown in Figure 21.9 displays, clicking Yes causes the resulting view to look like the view on the left in Figure 21.9. Clicking No causes the view shown in Figure 21.10 to appear.
FIGURE 21.10 Another Section view
Selected line Sketched lines
Aligned Section view The Aligned Section view takes two separate sections at right angles to one another and lays them out flat on the page. It is essentially two partial sections that display side by side. The section lines look identical to those shown in Figure 21.10, but the resulting view is different, as shown in Figure 21.11. The finished view aligns with the selected sketch element.
626
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 627
Working with Drawing Views
FIGURE 21.11 The Aligned Section view
Editing a Section view Section views are edited in the same way as detail views. You can edit the section lines directly by dragging, or the section line sketch through the RMB menu. You can use the Edit Sketch command through the section line RMB menu to edit sketch relations, or to add or remove sketch elements to the sketch. Section views are also deleted in the same way as detail views, with the option to also delete the underlying sketch for the section. When you delete one segment of the section line, the resulting view, as well as the underlying sketch, is also deleted.
Creating Other View Types SolidWorks is able to create any type of view that you need. If you can define what the view should look like, then SolidWorks can create it. The only limit is your creativity.
Crop view The Crop view is simply a view that looks like a Detail view without requiring a parent view. This feature allows you to reduce the number of views on a sheet, and save some room. However, a cropped view may be confusing if it is not clear which area is being detailed in the cropped view. Crop views have some limitations, including the inability to crop an assembly exploded view, a Detail view, or the parent of a detail view. Unlike Detail views, in Crop views, the closed loop must be sketched in the view before you invoke the command. To make the Crop view, draw the closed loop as shown in Figure 21.12 in the image to the left, and then click the Crop View button on the drawing toolbar or access the command at Insert ➪ Drawing View ➪ Crop.
627
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 628
Creating Drawings
FIGURE 21.12 A sketch loop and a Crop view
Editing a Crop view To edit a Crop view, RMB click the view, expand the arrow next to Crop View, and select either Edit Crop or Remove Crop. Removing the crop does not delete the sketch that the crop was created from.
Broken-out Section view The Broken-out Section view is another view type that alters an existing view rather than creating a new view. It also requires a closed loop sketch. The Broken-out Section view is very useful in assembly views where parts are obscured by other parts, in particular when a set of parts are inside a housing and you want to show the inside parts without hiding the housing. Of course, you can also use Broken-out Section views on parts with internal detail. Broken-out Section views act like a cut that is created from the drawing view. Any faces created by the cut are hatched. Figure 21.13 shows a simple assembly view using a Broken-out Section view. On the left is the view with the driving sketch (in this case, a closed loop spline), and on the right is the finished view. You cannot create Broken-out Section views using existing detail, section, or alternate position views.
628
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 629
Working with Drawing Views
FIGURE 21.13 A Broken-out Section view
Drawing the closed loop Broken-out Section views are initiated from an existing view either with or without a pre-drawn closed loop. If the loop is pre-drawn, then you must select it before clicking the Broken-out Section toolbar button on the Drawings toolbar or accessing the command at Insert ➪ Drawing View ➪ Broken-out Section. If the view has no pre-drawn, pre-selected loop, then initiating the function activates the spline sketch tool. It is not necessary to use a spline as the closed loop for this view type, but Broken-out Section views are traditionally created with a freehand sort of boundary, even when drawn manually. If the loop is closed in an uninterrupted workflow, then after the last spline point is drawn, joining the spline back to itself, the Section Scope dialog box appears. This enables you to select any parts that are not to be sectioned. It is customary to avoid sectioning shafts, screws, or other cylindrical components. Using the Section Scope, the image on the right in Figure 21.13 would be altered to look like the image on the right in Figure 21.14. The recommended workflow is to initiate the function from the toolbar, use the spline to create the closed loop, and to not pre-draw a loop. This makes everything flow more smoothly, and you create the view surprisingly quickly. If you must use a sketch tool other than the spline, then you must pre-draw it. Even if you simply change sketch tools when the Broken-out Section view automatically activates the spline, because the workflow has been broken, creating the closed loop does not automatically display the Section Scope interface.
629
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 630
Creating Drawings
FIGURE 21.14 Using the Section Scope
Selecting the depth After you make the Section Scope selections, the next step is to set the depth of the cut. You can do this in one of several ways. Broken-out Section views are usually applied to the center of a hole if available, or in other ways that show the view as cleanly as possible. If you know the depth of the cut that you want to make, then you can type it in as a distance value. Of course, that raises the question “Distance from what?” to which the answer seems to be “from the geometry in the view that would come the farthest out of the screen toward the user.” Users most often choose the distance when it does not matter exactly how deep the cut goes or exactly where it cuts, but to give a relative position. In situations when you want to cut to the center of a particular feature or up to an edge, it is far easier and less bothersome to simply select the geometry from a drawing view. For example, Figure 21.15 shows the PropertyManager interface where the depth of the cut is set. In this example, the edge of the shaft in the view to the right has been selected. This tells SolidWorks that the cut should go to the center of the shaft. Another possibility is to show the temporary axes, as shown in Figure 21.15, and to select an axis through the center of the shaft.
630
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 631
Working with Drawing Views
FIGURE 21.15 Setting the depth of the Broken-out Section view
Editing the view At this point the view is finished. Now you may choose to edit the view in some way, such as by changing the sketch, the depth, the section scope, and so on. Figure 21.16 shows how the Brokenout Section view is positioned in the Drawing FeatureManager. It is listed as a modification to an existing drawing view. The Broken-out Section RMB menu is also shown. Selecting Edit Definition displays the PropertyManager, shown in Figure 21.15. Selecting Edit Sketch enables you to change the section spline shape. Selecting Properties displays the dialog box shown to the right in Figure 21.16. This contains options for the underlying original view as well as the Broken-out section modification to the original view. Only the Section Scope tab is added by the Broken-out Section view. The rest of the options are for normal view properties.
FIGURE 21.16 Editing the Broken-out Section view
631
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 632
Creating Drawings
Break view Break views are typically used to display parts that are very long in one dimension on a drawing in such a way that you can see both ends, or other important features. You can break views more than once in the same direction, or even in opposite directions. Figure 21.17 shows the full view of a part and a view that was broken twice. Notice that the dimensions are correct, and any dimension that includes a broken length has a special dimension line.
FIGURE 21.17 Dimensions on a Break view
The PropertyManager in Figure 21.17 shows a bit of a discrepancy in terminology. Using “Break” as the name of the view seems a little awkward, and I much prefer it as it is shown here in the PropertyManager as “Broken View.” It is inconsistent, but you get the idea anyway. To create a Break view, click the Break toolbar button on the Drawings toolbar, or select it at Insert, Drawing View, Break. You need to place break lines in pairs, and you can choose from one of four break symbol styles, as shown in Figure 21.18. You can change the style from the RMB menu or from the PropertyManager. The Break command is a bit awkward to finish. If you press Esc, then all of the breaks that you placed are removed. There is no green check mark icon on the cursor RMB symbol as there are for many other functions in SolidWorks. As a result, the Confirmation Corner is probably the best way to exit this function and save your work. If you have worked with previous versions, then you may find that the current interface and functionality are vastly improved. In previous versions, you had to choose between Vertical Break and Horizontal Break. I could never tell the difference — were the break lines vertical or was the shortened distance vertical in a vertical break? In SolidWorks 2007, the icons display with tooltips, which clears up the confusion.
632
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 633
Working with Drawing Views
FIGURE 21.18 Selecting the break symbol
The Broken View PropertyManager also enables you to set the gap size and the style of the break. The gap refers to the gap between the break lines in the finished broken view. The setting here overrides the default for this view only. The default setting is a template setting found in Tools ➪ Options ➪ Document Properties ➪ Detailing. Other options that you can set in this location are the break line extension (the distance the lines extend past the model edges) and the break line font (on the Line Font page of the Document Properties tab). The setting that enables the broken symbol on a dimension is found on the Dimensions page, and is named Show Dimensions As Broken In Broken Views. You can remove individual breaks in a broken view by selecting one of the break lines and pressing Delete. You can add breaks by applying the Break command and adding more breaks to a view. You can alter breaks by simply dragging the break lines. In past versions, it was possible to get the view very confused by dragging one set of breaks to interfere with another set of breaks. That problem has been fixed by not allowing break lines to be dragged past one another.
Auxiliary view An Auxiliary view is a view that is projected from a non-orthogonal edge. This type of view is often necessary to view features (such as holes drilled at an angle) square on, so that they appear circular in the view rather than foreshortened and elliptical. An auxiliary view is shown in Figure 21.19 in the image to the left. If the edge that the view was created from is updated, then the auxiliary view will reorient itself. The image to the right shows an auxiliary view projected from an arbitrarily drawn sketch line. The line or edge used to project an auxiliary view cannot be reselected; however, if a sketch is used to project the view, then the Edit Sketch option is available through the view arrow RMB menu.
633
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 634
Creating Drawings
FIGURE 21.19 Two Auxiliary views
Alternate Position view The Alternate Position view is only available for views of an assembly, and shows the assembly in two different positions (not from different viewpoints; this requires an assembly that moves). This is another view type that does not create a new view, but alters an existing view. Figure 21.20 shows the PropertyManager interface for this view type, a sample view that it creates, and the way that it is represented in the drawing FeatureManager.
FIGURE 21.20 The Alternate Position view
634
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 635
Working with Drawing Views
To create an Alternate Position view, ensure that you have an assembly on the active drawing that can have multiple positions, and click the Alternate Position View button from the Drawings toolbar, or select the same tool at Insert ➪ Drawing View ➪ Alternate Position. Next, click in the drawing view to which you want to add the alternate position. The PropertyManager shown in Figure 21.20 prompts you to select an existing configuration for the alternate position or to create a new configuration. If you choose to create a new config, then the model window appears, a new config is created, and you are required to reposition the assembly. The alternate position is shown in a different line font on the same view, from the same orientation as the original. The best way to create this view is to either create two configurations that are used exclusively for the Alternate Position view, or to have two configurations where you know that parts will not be moved, suppressed, or hidden. The main idea is that you need to ensure that these configurations remain in the same position or are changed intentionally, knowing that it will alter this drawing view.
TIP
To delete an Alternate Position view, select it in the drawing FeatureManager, and press Delete.
Predefined view Predefined views are discussed in depth in Chapter 20.
Empty view Empty views are just that — empty. The reasons for creating an Empty view can include making a view from a sketch, or a schematic from blocks, or combining several elements — such as blocks, sketches, imported drawing geometry, annotations, and symbols — into an entity that can be moved as a group on a drawing.
Custom view You can create Custom views by orienting the view in the model document, and saving the view. Remember that views can be saved in the View Orientation window, which you can access by pressing the spacebar. Custom views are placed on the drawing using the Named View functionality. While not appropriate for showing dimensions, views using perspective are most useful for pictorial or illustrative views. The only way to get a perspective view on a drawing is to save a custom view in the model with perspective turned on. You can access the Perspective option at View ➪ Display ➪ Perspective, and you can edit the amount of perspective at View ➪ Modify ➪ Perspective.
635
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 636
Creating Drawings
Relative view The Relative view enables you to create a view that does not necessarily correspond to any of the standard orthogonal views or named views. This type of view is very similar to using the Normal To tool. First select the face that is to be presented square to the view, and then select the face that represents the top of the view. When this view type is initiated, SolidWorks opens the 3D model window to allow you to select the faces needed to define the view. This type of view is particularly useful when a part has a face that is at an odd angle to the standard planes of the part. It is in some ways similar to the Auxiliary view, except that in the Auxiliary view you cannot select which face is the top. The Relative view has a special function that is important for drawings of multibody parts. If both faces used to establish the view are from the same body, then all of the rest of the bodies in the part can be hidden with an option in the Relative View PropertyManager, which is shown in Figure 21.21. This functionality is particularly useful in Weldments and is covered in more detail in Chapter 31. Multibody modeling is covered in Chapter 26.
FIGURE 21.21 The Relative View PropertyManager
3D Drawing View Mode 3D Drawing View Mode is not technically a drawing view type. It is a mode that enables you to select faces or edges of the model that may need to be selected for some purpose, but cannot be seen from the orientation of the drawing view. You can invoke the 3D Drawing View Mode from the 3D Drawing View toolbar button, which is on the View toolbar and can be accessed via the menus at View ➪ Modify ➪ 3D Drawing View.
636
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 637
Working with Drawing Views
Ironically, this mode does not work for the Relative view, which would be a perfect application for it. It is intended for views such as the Broken-out Section view where a depth must be selected for the cut. In Figure 21.22, notice the small toolbar above the drawing view. This toolbar is available while the 3D Drawing View Mode is turned on. Clicking OK on the small toolbar turns off the mode and returns the view to its previous state.
FIGURE 21.22 3D Drawing View Mode
View orientation and alignment Although you may have selected the Top view, and it displays the correct geometry, you may want to spin the view in the plane of the paper, or orient it in a particular way. You can do this using two methods. The easiest way to reorient the view is to use the Rotate View tool on the View toolbar. This rotates the view in the plane of the paper much like it rotates the model in 3D. Another option is to select an edge in the view and assign the edge to be either a horizontal or vertical edge. Figure 21.23 shows how a view can be re-oriented using this tool, which is located at Tools ➪ Align Drawing View ➪ Horizontal or Vertical Edge. Another option for view alignment is to align it relative to another view; this involves stacking one view on top of another or placing them side-by-side. You can do this by selecting the second pair of options in the menu shown in Figure 21.23, Horizontal to Another View and Vertical to Another View. Situations may arise where a view is locked into a particular relationship to another view, and you need to disassociate the views. The Break Alignment option, which is grayed out in the menu in Figure 21.23, serves that purpose. Default Alignment resets a view to its original orientation and alignment if it has been altered.
637
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 638
Creating Drawings
FIGURE 21.23 Rotating a drawing view to align an edge
Selected edge
Using Display Options in Views Some important display options and settings are not listed in Tools, Options, but are only available through the menus. You can find more information about the display options and settings that are available through Tools, Options in Appendix B.
Display States Display States can be used in drawing views, but they only have an effect when a drawing view is set to Shaded Display mode. You can control Display States for drawing views in the View Properties tab of the Drawing View Properties dialog box. RMB click inside the view but away from any geometry, and select Properties. The Drawing View Properties dialog box appears, as shown in Figure 21.24. One of the limitations of the Display States functionality in drawing views is that when wireframe display is used, the drawing edges appear black rather than using the color settings to show wireframe in the same color as shaded.
638
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 639
Working with Drawing Views
FIGURE 21.24 The Drawing View Properties dialog box
Display modes With even the 2D drawing world becoming less and less black-and-white, SolidWorks drawings have the ability to apply shaded views to drawings. This is probably most useful in isometric, perspective, or pictorial views on the drawings. The shading and color may be distracting for dimensioned and detailed views, but it can also be indispensable when you need to show what a part actually looks like in 3D. Not everyone can read engineering prints, and even for those who can, nothing communicates quite like a couple of shaded isometric views. The more standard 2D drawing display modes are Wireframe, HLR (hidden lines removed), and HLV (hidden lines visible), which work in the same way as they do in the model environment. Unless you override it, the Display mode is set for all of the components in the view.
Component Line Font Individual components within an assembly can be shown in different fonts, similar to the display in the Alternate Position view. You can access this function through the component RMB menu, by selecting Component Line Font. Figure 21.25 shows the Component Line Font dialog box, along with a drawing view in which a couple of part line fonts have been changed. The part can only be changed in the view where it was selected, or it can be changed across the board in all views in the active drawing where it appears. This is useful if you want to emphasize or de-emphasize certain parts in the assembly view.
639
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 640
Creating Drawings
FIGURE 21.25 The Component Line Font dialog box
Layers Yes, SolidWorks drawings can use layers. No one likes to admit this, but it is nonetheless true. You can place individual parts onto layers, and the layers can have different colors and fonts. Most entities can be put into layers, including edges, annotations, and sketch items. Hidden layers are often used for reference information or construction entities on a drawing.
Edge display options SolidWorks drawings and models offer some options for displaying tangent edges. Many users find it distracting when tangent edges (which in a physical part are not edges at all) are given as much visible weight as the sharp edges of, say, a chamfer. These settings are found at View ➪ Display, as shown in Figure 21.26. The Tangent Edges Removed option may be appropriate for parts with few fillets, but it causes a part to look over-simplified and makes details of the shape difficult to distinguish.
FIGURE 21.26 Edge display options
Tangent edges removed
Tangent edges visible Tangent edges with font
640
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 641
Working with Drawing Views
View quality settings View quality is one of those issues that keep users confused because it has changed so many times in recent releases. If you look for view quality settings, then you may be looking for some time. Are the settings with the view, the sheet, system options, document properties? Where are they? You have the choice between two options for drawing view quality: high quality and draft quality. The quality that you choose influences the performance of the software. Draft quality views are noticeably rough when viewed closely, but from a distance, they are at least recognizable. However, Draft quality is becoming less accessible, and so I would not recommend relying on this option. Although new Draft Quality views can be created, once they are set to High Quality, they cannot be set back to Draft Quality. In SolidWorks 2007, all views are created as High Quality unless the view quality setting is overridden. This setting is found at Tools ➪ Options ➪ System Options ➪ Drawings ➪ Display Style ➪ Display Quality For New Views. The only other way that you can create Draft Quality views in this version is if you open a drawing from an older version of SolidWorks that used draft quality views. In Figure 21.2 earlier in the chapter, the image to the right shows the Display Style pane. This PropertyManager has been taken from a High Quality view. A Draft Quality view enables you to toggle between Draft and High quality, as shown in Figure 21.27. This means that you can switch a view from Draft to High, but not from High to Draft. Also notice in Figure 21.27 that the cursor over a Draft Quality view displays a lightning bolt symbol, indicating draft quality.
FIGURE 21.27 The Draft Quality options and cursor
You can access the Cosmetic Thread Display setting in both the Step 1 PropertyManager and the Step 2 PropertyManager. However, you need to be careful not to misread the interface, by thinking that either of these interfaces controls the View Quality. The best advice for using the view quality settings is to forget about them. It looks like this function is being phased out or at least discouraged.
641
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 642
Creating Drawings
Distinguishing Views from Sheets It is sometimes difficult for new users to understand the difference between being in a sketch and being out of a sketch, or the difference between editing the sheet as opposed to the sheet format. In the same way, confusion frequently surrounds the difference between sketching in a view and sketching on a sheet. The easiest way to determine if a sketch will be associated with a view or with the drawing sheet is to look at the prompt in the lower-right corner of the SolidWorks window, on the status bar, which displays the message, Editing Sheet, Editing Sheet Format, or Editing View. This issue becomes especially important when you want to do something with a sketch entity, but it is grayed out and unavailable. This means that whatever entity is active is not the one that the sketch entity is on. Drawing views expand to contain all of the sketch entities that are associated with the view, and so if you see a view that is extended on one side, larger than it should be, then it could be extended to contain the grayed-out sketch entity. Activate the sheet and the suspected views; when the sketch entity turns from gray to black, you have found the place where it resides.
Tutorial: Working with View Types, Settings, and Options This tutorial is intended to familiarize you with many of the view types, settings, and options that are involved in creating views. To begin, follow these steps: 1. From the CD-ROM, open the part called Chapter 21 – Tutorial Part.sldprt. 2. Move the drawing template named Inch B Bible Template.drwdot, also found on the CD-ROM, to your templates folder. If you do not know where your templates are located, go to Tools ➪ Options ➪ System Options ➪ File Locations ➪ Document Templates. 3. From the window with the open part, click the Make Drawing from Part button from the toolbar. The drawing becomes populated with three standard views and an isometric view, as shown in Figure 21.28. 4. In the drawing document, turn on the display of the Origins. This will help you to align a section view. Origins can be displayed through the menus at View ➪ Origin. 5. Click the Section View tool on the Drawings toolbar. This activates the Line sketch tool.
642
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 643
Working with Drawing Views
FIGURE 21.28 Using a template with Predefined views
6. In the Top view (in the upper-left section of the drawing), draw a line that picks up the inference from the Origin. You may have to run the cursor over the Origin to activate the inference lines. Make sure that the line goes all the way through the model geometry in the view, as shown in Figure 21.29. When you finish the line, the section view is ready to be placed. Place it to the right of the parent view.
FIGURE 21.29 Creating a section view
643
21
30_080139 ch21.qxp
Part V
3/26/07
4:13 PM
Page 644
Creating Drawings
When sketching, remember to make sure that you are sketching in the view rather than on the sheet. A section view cannot be created from a sketch entity if it is not in a view. A glance at the status bar in the lower-right corner of the window lets you know if you are in Editing View or Editing Sheet. To change the letter label on the drawing, click the section line and change the label in the top panel of the Section View PropertyManager. 7. Bring the cursor over the sharp bend in the section line until the cursor looks like the image to the left. Double-click the cursor; the section arrows flip to the other direction, and the drawing view becomes cross-hatched. The cross-hatching indicates that the view needs to be updated. 8. Press Ctrl+Q; the view updates, removing the cross-hatching. 9. Click the section line and press Delete. Answer Yes to the prompt. If you are familiar with older versions of SolidWorks, then you may notice that the original sketch is also deleted with the section line and the view, so that you do not have to delete separate elements individually. 10. Create a new section view using a jogged section line, as shown in Figure 21.30. In order to do this, you must pre-draw the jogged section line, and press the Section View button with the part of the line that you want to use to project the new view.
FIGURE 21.30 Creating a jogged section view
11. Next, click the Detail View button on the Drawings toolbar. This activates the Circle sketch tool. 12. Sketch a circle in the Front view, located in the lower-left section of the drawing. Try not to pick up any automatic relations to the center of the circle. One way to prevent this is to hold down the Ctrl key when creating the sketch. 13. Place the view when the circle is complete. Note that the view was created at a scale of 1:2. The sheet scale is 1:4, and so the detail is two times the sheet scale. The Detail view is shown in Figure 21.31.
644
30_080139 ch21.qxp
3/26/07
4:13 PM
Page 645
Working with Drawing Views
FIGURE 21.31 Creating a Detail view
14. Drag the circumference of the circle and watch the view dynamically resize. 15. Leave the Detail circle selected so that the center of the circle is highlighted. Drag the center of the circle around the view. The effect is like moving a magnifying glass over the part. If you drag the center with the Ctrl key pressed, then you will not pick up any automatic sketch relations when you drop it somewhere. 16. Click the Broken-out Section View tool on the Drawings toolbar. Draw a spline similar to the one shown in the image to the left in Figure 21.32. Splines take a little practice.
FIGURE 21.32 Creating a Broken-out Section view
17. Click inside the view border but outside of the part in the Top view (in the upper-left section of the drawing). Press Ctrl+C. 18. RMB click the tab in the lower-left corner of the drawing that says Sheet1, and select Add New Sheet. If you used the template that I provided, a message may appear, saying that SolidWorks cannot find the format. This is because I only supplied you with the template file, not the format as a separate file. In any case, switch to the B size format and accept.
645
21
30_080139 ch21.qxp
Part V
3/26/07
4:14 PM
Page 646
Creating Drawings
19. Click any spot inside the sheet and press Ctrl+V. SolidWorks pastes the copied view from the other sheet. Delete the section line. 20. Click the Projected View tool from the Drawings toolbar, and then click the pasted view. Practice making a couple of projected views, including dragging one off at a 45-degree angle to make an isometric. Make sure that one of the views is a side view showing the angled edge, as shown in Figure 21.33. Once you create the views, click model edges in the views and drag them around to a better location.
FIGURE 21.33 Projecting views
Create at least one of these views
21. Select the angled edge from one of the side views and click the Auxiliary View toolbar button. While placing the view, press and hold the Ctrl key to break the alignment. You can resize the view arrow by selecting the corners and dragging. If you drag the line itself, then you can move it between the views. Alternatively, with the view arrow selected and the PropertyManager displayed, you can deselect the green check mark icon in the Arrow panel at the top of the window to turn off the arrow. 22. Create a new drawing from the New dialog box. If the automatic Model View interface appears in the PropertyManager, click the red X icon to cancel out of it. 23. Expand the Task pane and activate the View palette (the tab that looks like a drawing icon). Click the ellipse button (. . .) and browse for the assembly named Chapter 21. SF casting assembly.sldasm. This is shown in Figure 21.34.
646
30_080139 ch21.qxp
3/26/07
4:14 PM
Page 647
Working with Drawing Views
FIGURE 21.34 The View palette
24. Drag the Back view onto the drawing. Notice that when you use this technique, the views do not resize automatically, regardless of the setting at Tools ➪ Options ➪ Drawings ➪ Automatically Scale New Drawing Views. 25. Delete any view that you have created using this method. Open Windows Explorer, browse to the assembly, and drag it into the drawing. The views that you create using this method are equivalent to the Standard 3 View tool. This time, the views auto-size. 26. Select the Front view and change it to the Back view. Notice that the rest of the views change to reflect the new parent view. 27. Zoom in on the Back view. Change the view to show Tangent Edges With Font through View ➪ Display. 28. Click the Alternate Position view toolbar button. Type a name in the PropertyManager for a new configuration and click the green check mark icon. SolidWorks opens the assembly model window. 29. Rotate the handle 90 degrees and click the green check mark icon. SolidWorks returns to the drawing and shows the new position in a dashed font, as shown in Figure 21.35. 30. Place an isometric view on the drawing. Change the Display Mode to make it a shaded view.
647
21
30_080139 ch21.qxp
Part V
3/26/07
4:14 PM
Page 648
Creating Drawings
FIGURE 21.35 Creating an Alternate Position view
31. RMB click inside the view but away from the parts, and select Properties. The dialog box appears, as shown in Figure 21.36. Make sure that the view is set to use the Default configuration, and also select the Show in Exploded State option.
FIGURE 21.36 The Drawing View Properties dialog box
648
30_080139 ch21.qxp
3/26/07
4:14 PM
Page 649
Working with Drawing Views
Summary SolidWorks has the capacity to make many different types of views of parts and assemblies. In addition to the tools for projecting views, custom views saved in the model document can be saved and used on the drawing. The associative nature of the drawing to the model helps ensure that drawing views, regardless of how unusual the section angle or view orientation, are displayed in the correct size, location, and geometry. It is sometimes better to create some of the views that require sketches by pre-sketching. Make use of workflow enhancements when possible; for example, the Broken-out Section automated workflow works well, but forcing it to be a manual process makes it awkward to use.
649
21
30_080139 ch21.qxp
3/26/07
4:14 PM
Page 650
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 651
Using Annotations and Symbols
A
nnotations and symbols are a major component of communicating a design through a drawing. SolidWorks has several options available to help you manage these entities to make engineering drawings look good and communicate effectively.
IN THIS CHAPTER Using notes Using blocks Using symbols
Using Notes Notes are the workhorse of SolidWorks annotations. You can use notes in many different configurations, and mix them with links to custom properties, hyperlinks, and text wrapping boxes. You can also use them with favorites, leaders, balloons, and symbols.
The workflow for placing notes Sometimes users have difficulty working through some of the interfaces in SolidWorks. This is not necessarily the fault of the software, but is often because users may not fully understand how the workflow of a particular feature is supposed to function. The Model View interface from the last chapter is one that can be confusing until you have been through it a few times and gain a more intuitive feel for how it works. Understanding the workflow is paramount to being able to use the software efficiently. I sometimes find myself using the Annotations clumsily, and sometimes wind up with blank notes, double notes, or extra lines at the ends of notes. After using the tool a few times, I get back in the groove. For these reasons, I have added some step-by-step suggestions here to help you establish expectations that will enable you to use a fast workflow with annotations.
651
Using center marks and centerlines Tutorial: Using annotations
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 652
Creating Drawings
Follow these steps to create a note: 1. Click the Note toolbar button on the Annotations toolbar. 2. Click in the graphics window where you want to create the note or click an entity that you want the note leader to point to, and then click where you want the note. 3. Type the note. Press Enter at the end of a line, or, if you intend to force the note to wrap, just allow the line of text to be as long as it wants to be. While you create the note, the text box expands to the right until you press Enter, and it expands down every time a line is added.
At the end of the last line of the note, do not press Enter again (this creates extra lines) and do not press Esc (this causes the entire note to disappear). 4. To finish the note, click the mouse outside of the text box. After that, if you are done, press Esc. If you want to continue with another note, click again to place it, and start typing. If you want to place the same note as the first one again, the text is already there, so click a second time.
Fonts SolidWorks uses any TrueType fonts that Windows will accept. This includes symbol, non-English, and Wingding fonts. SolidWorks does not use true monofonts like AutoCAD, because they do not have width information. Some look-alike fonts are installed with SolidWorks that do have a very narrow width, and are shaped like some of the monofonts. If you are a long-time SolidWorks user, you will be pleased to know that in recent versions of the software, different pieces of text within a single note can be formatted with multiple fonts, multiple sizes, bold, italics, underline, and so on. The Fonts toolbar displays with two different names. If you use it in the CommandManager, it displays with the Fonts name, with the icon shown at the beginning of this Fonts section. In Tools, Customize, the Fonts toolbar displays as the Formatting toolbar. The Formatting toolbar also appears in the graphics area immediately over your text every time you either insert a new note or edit an existing note, unless the toolbar is already docked somewhere. The Formatting toolbar is shown in Figure 22.1.
FIGURE 22.1 The Formatting toolbar
Text boxes and wrapping Text boxes are a more recent addition that enables the user to limit the size, particularly the width, that a note can occupy. This enables notes to wrap in tight spaces on title or revision blocks, as well as other places.
652
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 653
Using Annotations and Symbols
You can size text boxes immediately after placement, even while they are blank; the text then wraps as you type it. The text box expands downward automatically. Blank text boxes can be left on the drawing to provide a placeholder for future text. The blank text box has a rectangular border that contains an X, both of which are removed when you add text. If spaces are added to a text box, the text box becomes invisible, although you can select it if you know where it is. When you move the cursor over the text box, the cursor displays the note symbol. Text boxes do not highlight when window selected. While typing a note, it is not possible to resize the note using the middle handle on the right end of the box; you should use the lower-right corner handle, as shown in Figure 22.2.
FIGURE 22.2 Resizing a text box using the lower-right corner handle
Do not resize box with middle handle Use corner handle to resize
If a custom property is used to populate a note, and the value of the property is long, you may have difficulty getting the text of the property to wrap. One way to accomplish this is to make the font of the note very small, then size the box to the appropriate size, then set the note font back to the original size. The text now wraps to fit the box.
Notes and leaders When you start to place a note, a preview shows the text box with or without a leader depending on the position of the cursor. If the cursor is over a blank section of the drawing, the note is placed without any leader. If the cursor is over a face, edge, or vertex, then a leader is added using the arrow controlled by the settings at Tools ➪ Options ➪ Document Properties ➪ Arrows ➪ Attachments. By default, a leader attached to a face uses a dot as an arrow, and a leader attached to an edge, sketch entity, or nothing at all uses a regular arrow. You can change these defaults at the options location mentioned above, and you can change individual note leaders in the PropertyManager that becomes available when you select a note. Figure 22.3 shows the preview that is displayed by the cursor when you place a note over a face, over an edge, and over blank space on the drawing. You can also change settings for bent leaders in the Tools ➪ Options ➪ Document Properties area. It is recommended that you use the same bent leader lengths for all annotations, and save them in the templates that you use.
653
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 654
Creating Drawings
FIGURE 22.3 Placing a note with a leader
Some minor but basic functionality appears to be missing from notes in SolidWorks. Single-clicking inside an active text box places the cursor between letters, as expected. Double-clicking inside an active text box selects the entire word that you click, again as expected. Triple-clicking in Microsoft applications such as Word and PowerPoint generally selects the whole paragraph or the contents of the text box. However, the triple-click option is not available in SolidWorks notes. Ctrl+A does work to select all of the text inside a text box. To format the entire note, do not activate the text box; instead, only select the note, and apply the setting to the entire note rather than to selected text within the note. You also cannot drag-and-drop selected text to move it within a text box. However, you can Ctrl+C, Ctrl+X, and Ctrl+V the text.
Adding a leader to a note To add a leader to a note that was created without a leader, click the note and select the leader options in the Leader panel of the PropertyManager, as shown in Figure 22.4. After you add the leader, you can reposition the handle at the end of the leader to attach it to an entity on the drawing.
FIGURE 22.4 Adding a leader to a note
654
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 655
Using Annotations and Symbols
Multiple leaders You can also attach multiple leaders to notes. To create a new note with multiple leaders, preselect the entities that the leaders are to be attached to, and then click the Note toolbar button. To add a leader to an existing note, first click the note, and then Ctrl-drag the handle on the end of the leader to the second location. A note with multiple leaders is shown in Figure 22.5. To remove one of multiple leaders from a note, click the handle at the end of the arrow and press Delete.
FIGURE 22.5 A note with multiple leaders
Jogged leaders Jogged leaders have come a long way since their introduction many releases ago. You can switch a regular leader to a jogged leader by selecting an option in the PropertyManager. In Figure 22.4, the middle icon in the top row is the Jogged Leader icon. The icon to the left simply turns on the default leader, and the icon to the right turns off leaders altogether. Once you activate the jogged leader option, you can add a jog from the leader RMB menu. Notice in Figure 22.6 that two options give you control over the jogged leader.
FIGURE 22.6 Jogging a leader
655
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 656
Creating Drawings
Add Jog Point Selecting the Add Jog Point command adds a new handle to the leader that you can move around. You can add multiple jog points to the leader.
Insert New Branch The Insert New Branch command enables you to create a new jogged leader that ends in another arrow from the selected point. This arrangement with multiple branches in a jogged leader is shown in Figure 22.7.
FIGURE 22.7 The results of adding a new branch to a jogged leader
Favorites For notes, a favorite can apply a font, an underline or bold formatting, or any other setting from the Formatting (Fonts) toolbar. To create a note that uses the favorite setting from another existing note, pre-select the existing note before starting the Note command; SolidWorks applies the favorite to the new note. Sometimes adding a favorite to a note can make other changes that you may not expect, such as turning off the leaders if a note has multiple leaders. In particular, if the favorite is made from a note with a jogged leader, then it turns off leaders for regular multiple leaders. Favorites that are created from regular leader notes do not turn off jogged leaders.
CAUTION
Making a change to the leader of a note after you apply the favorite removes the favorite from the note, although the formatting remains. This does not apply to adding multiple leaders, only to changing the type of leader. Applying a favorite may also remove the ability of the text to wrap, as well as any changes to the text box shape. You cannot move the corner of a text box of a note to which you have applied a favorite.
Favorites exist only in the document in which they were created, but they can be shared to other documents by saving the favorite out as a separate file. Note favorites use the extension, *.sldnotefvt. Once you save the favorite, you can load it into other documents. The Favorites panel of the Note PropertyManager interface is shown in Figure 22.8.
656
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 657
Using Annotations and Symbols
FIGURE 22.8 The Favorites panel of the Note PropertyManager interface
The Favorites panel contains the following buttons: Apply Defaults/No Favorites: Removes favorite settings from the current interface, setting all values back to the defaults. Add or Update Favorites: This can be used to either add a new favorite to the database or to change the name or other settings for an existing favorite. Delete Favorite: Removes a favorite from the database. Save Favorite: Saves a favorite to an external file (*.sldhwfvt), which can be loaded by other users and added to their databases. Load Favorite: Loads a saved favorite file. Favorites can be loaded into document templates so that for every document created from the template, those Favorites will be available.
Linking notes to custom properties You can link notes to custom properties. The custom properties can be from the drawing, or from the model that is referenced by the drawing. This kind of link is also mentioned briefly in Chapter 20, but I discuss it more thoroughly here. Figure 22.9 shows a note on a drawing with custom property links pulling data from the model shown on the drawing. To add these links, driven by the syntax $PRPSHEET:”material”, click the icon indicated in the image to the right in Figure 22.9. In this case, text has been combined with custom properties, but custom properties can also appear alone. The Custom Properties interface is found at Tools, Properties.
Hyperlinking text Hyperlinking text is sometimes useful on drawings to provide a link to reference documentation, specification, test results, and so on. The first button in the Text Format panel enables you to add a hyperlink to text in the note. Either copy the URL to the hyperlink dialog box that appears, or browse to it from the dialog box.
657
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 658
Creating Drawings
FIGURE 22.9 Linking notes to custom properties
Link to Custom Properties Hyperlink text
Add symbol
Notes and symbols Notes and symbols are regularly combined in SolidWorks. Symbols are discussed more fully later in this chapter, but are mentioned here because of the frequency with which they are used with notes. The image to the right in Figure 22.9 shows the Text Format panel, which contains a button to the interface where you can add symbols.
Using Blocks Blocks in SolidWorks can contain sketch elements and notes. When used in drawings, blocks have several common uses, including the following: n Standard note blocks for tolerances, disclaimers, or default requirements n You can put together a mechanism in 2D where each block represents a part n Flow direction for fluid systems n Drawing stamps such as “Not For Release,” “Preliminary,” “Obsolete,” and so on n Symbols for schematics which can be snapped together n You can save drawing templates as blocks to make them easier to place as a single entity Like favorites, blocks reside in the document in which they are created, but you can save them out to a *.sldblk file, load them into other documents, and save them as a part of a document template.
658
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 659
Using Annotations and Symbols
Inserting blocks You can apply blocks in several ways, including by dragging from Windows Explorer and by using the menus at Insert ➪ Annotations ➪ Block. However, the most efficient way is to access them from the Design Library. Library folders can be established specifically for blocks. Check the settings at Tools ➪ Options ➪ File Locations ➪ Blocks, and redirect this setting to a library area outside of the SolidWorks installation directory. Figure 22.10 shows the Design Library with a folder containing blocks that are selected. The blocks do not show previews in the window, but the tooltip displays large previews. You can drag blocks from the Design Library onto the drawing sheet.
FIGURE 22.10 Blocks in the Design Library
Each block has an insertion point, which snaps to any sketch entity endpoint, even if it is in another block. This makes schematics easy to snap together. If the default insertion point is not the point that you need to snap to the other geometry, then you can place the block anywhere on the drawing and drag the point that needs to snap. Once blocks are snapped together, to detach them from one another, you can click the point at which they touch; a Coincident sketch relation displays in the PropertyManager. Deleting the sketch relation enables you to drag the block away from the other geometry. When blocks are inserted, you can control several options in the PropertyManager. This function may be somewhat hidden because it does not appear automatically when you place the block. After you place the block, SolidWorks wants you to place another copy of the block. If you press Esc to cancel out of placing additional blocks, then the first placed block is not selected, and so the PropertyManager does not display. Figure 22.11 shows the Block PropertyManager.
659
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 660
Creating Drawings
FIGURE 22.11 The Block PropertyManager
Existing Relations This panel lists the sketch relations that are linked to the block. These may cause the block to not move properly when you drag it. This feature is most helpful when the block is being used as a representation of a part in a simulated 2D mechanism.
Definition Blocks can be linked to an external file, which enables all linked instances of a block to be updated at once, even if they are being used in other drawing documents. The path box for the Link to File option only displays if you select the check box.
660
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 661
Using Annotations and Symbols
The Edit button refers to editing the block. A toolbar button also exists for editing blocks. The Leader & Insertion Points button enables you to edit both of the controls. You can use the For Construction option to change any sketch entities in the block to construction entities.
Parameters The top field with the two circles to the left controls the scale of the block. This number affects the entire block, including the text. You also have the option to scale dimensions. The Lock Angle option refers to the rotation of the block. If the Lock Angle option is not selected, then you can rotate the block if one point on it is coincident to a stationary object, such as a vertex in a drawing view.
Leader You will recognize these options from the Notes leaders. The leader is attached to the block where the angled black handle was placed when you created the block.
Text/Dimension Display The Display Dimensions option controls whether or not any notes and dimensions in the block are displayed or hidden.
Layer You can assign most entities on drawings to layers, which in turn have controls for items, such as line type, color, and visibility.
Creating blocks You can create blocks by selecting the sketch and annotation elements and clicking the Make Block toolbar button from the Blocks toolbar, or by accessing the command through the menus at Insert ➪ Annotations ➪ Block. Sketch Blocks have been covered in some detail in Chapter 4. The current chapter is limited to a discussion of blocks that may be found on drawings rather than those used in model sketches.
CROSS-REF
By default, when you create a block, the Insertion Point panel of the PropertyManager does not expand. If you expand this panel, the blue Origin symbol represents the insertion point that is attached to the cursor during block insertion, as shown in Figure 22.12. The angled line hanging off of the left side of the block is the leader attachment point for the block. You can also drag this line around the block and snap it to sketch geometry. By default, this block does not use a leader, but if one is required, then you can turn it on when you place the block.
661
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 662
Creating Drawings
FIGURE 22.12 Creating a block
Editing blocks Although you do not have many options when creating blocks, many more options become available when you edit them. You can access editing options for a block from four locations: n The Edit Block toolbar button on the Blocks toolbar n The Edit button in the Block PropertyManager n Through the menus at Tools ➪ Block ➪ Edit n From the RMB menu of the block in the Blocks folder in the drawing FeatureManager The standard edit function gives you access to the sketch and note elements that make up the block.
Add/Remove Entities While you are editing the block, the Add/Remove Entities button on the Blocks toolbar becomes available. This enables you to add or remove sketch or note entities from the block definition.
Rebuild When you are finished editing the block, and you need to leave Edit mode, you can use the Rebuild button to do so.
662
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 663
Using Annotations and Symbols
Explode This is not technically an edit option, but it certainly does change things. Explode is available when you are not editing the block, but when it is selected. Explode returns the contents of that particular instance of the block to the drawing, removing them from the block. This removes any leaders that are attached to the block, as well as sketch relations.
Using Symbols SolidWorks symbols are different from symbols that are a part of a font family. SolidWorks symbols fall into several categories including, weld, surface finish, hole, modifying symbols, GD&T, and several flag symbols. You can also construct custom symbols.
Where can you use symbols? You can use symbols in notes and dimensions. They also are an intrinsic part of weld symbols and surface finish symbols. Hole Callouts use symbols extensively, as do GD&T (geometric dimensioning and tolerancing) frames. Figure 22.13 shows the Text Format panel from the Note PropertyManager and the Dimension Text panel from the Dimension PropertyManager. Both of these interfaces give you access to the symbol library.
FIGURE 22.13 Accessing symbols and the symbol library
663
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 664
Creating Drawings
Custom symbols You can create custom symbols in SolidWorks, but creating them may not be as simple as you expect. In the lang\english subfolder of the SolidWorks installation directory is a file called Gtol.sym. This is the file that stores the representations of all of the SolidWorks symbols. This is also the file where you can create symbols of your own. You can edit the file in Notepad. As a warning, unless you enjoy writing scripts for the command line, or you are a fan of DOS 5.0, then you may not want to create custom symbol projects. The format for creating symbols is simple enough, but it is what you might call somewhat arcane. It is effective at creating line-art symbols that can be used with text and can even be used to contain text. If you are a little inventive with this, then you can create interesting shapes that integrate with your notes and dimensions. Keep in mind that this topic does not appear in the Help files, but all of the instructions you need are inside the file itself. You may have to experiment a little to discover what the rules are in terms of making shapes outside of the limits of the 1X1 matrix.
Using Center Marks and Centerlines You can apply center marks either manually or automatically to edges that appear circular in the drawing view. The settings to control automatic insertion are found at Tools ➪ Options ➪ Document Properties ➪ Detailing ➪ Auto Insert on View Creation. The size of the mark at the center and the use of lines extending to the actual circular edge are also controlled on this tab, in the Center Marks section.
NEW FEATURE
Starting with 2007, there is now an option in Tools ➪ Options ➪ Document Properties to exclude center marks from arc edges created by fillets.
Figure 22.14 shows some of the options that are available for center marks. Center marks propagate well to patterns, and you can dimension to them individually. You can rotate center marks in views where they need to be referenced from an edge that is not parallel to horizontal. You can also place center marks into layers. You can apply centerlines to any geometry that has a temporary axis that is perpendicular to the drawing sheet. Centerlines can also be placed automatically when you place the part into the drawing. You can create centerlines by selecting a face or a pair of parallel lines or concentric arcs. Centerlines may be displayed improperly on parts that are created by mirroring, as shown in Figure 22.15.
664
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 665
Using Annotations and Symbols
FIGURE 22.14 Options that are available for center marks
Select symbol to propagate center mark to pattern
665
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 666
Creating Drawings
FIGURE 22.15 Centerlines can display improperly on a mirrored part.
Tutorial: Using Annotations This tutorial shows you how to use some of the tools that were discussed in this chapter. It does not cover every feature, and so you should explore a little on your own, and not necessarily follow the instructions exactly. Start here: 1. From the CD-ROM, open the file named Chapter 22 – Tutorial.slddrw. This is a drawing file with views of the part from Chapter 21, but it does not contain dimensions or annotations. 2. Click the Center Mark tool on the Annotations toolbar. (If the button is not there, then use Tools ➪ Customize ➪ Commands to place it on the toolbar, along with the Centerline tool.) Click one of the holes in the pattern of three, and click the Propagate symbol to propagate the center marks to all three holes in the pattern. The view should look like Figure 22.16 when you are done. 3. Activate the Centerline tool to add two centerlines to the right view, in the lower-left area. Select the cylindrical faces for each feature to place the centerlines. Click the vertical centerline and drag the ends past the edges of the part. 4. Select the edge that is indicated in Figure 22.17, and initiate a note from the Annotations toolbar. Type the text shown, all in one line. You can place the degree and diameter symbols from the symbol library, which you can access using the indicated button in the PropertyManager. Both symbols are in the Modifying Symbols library, also shown in Figure 22.17. Drag the lower-right corner of the text box to make the text wrap as shown. 5. Draw an arrow with a text note inside it, as shown in Figure 22.18. Make the sketch and text into a block by window-selecting all of it and clicking Make Block from the Blocks toolbar, or by selecting Tools ➪ Block ➪ Make. Make sure that the end of the arrow is its insertion point. You have to expand the Insertion Point panel in the PropertyManager to access this option. When the block is set up, accept it by clicking the green check mark icon. When the block is created, delete it from the drawing. 6. Place the block using the Insert Block function, so that the block is to the right of the right view. Once you place it, press Esc to cancel the placement of more blocks. Then select the block to activate the PropertyManager. Deselect the Lock Angle option, and set the angle to 270 degrees.
666
31_080139 ch22.qxp
3/26/07
4:14 PM
Page 667
Using Annotations and Symbols
FIGURE 22.16 Center marks and centerlines on a part
Add centerlines by clicking cylindrical faces
FIGURE 22.17 Placing symbols in an annotation
Access the symbol library
667
22
31_080139 ch22.qxp
Part V
3/26/07
4:14 PM
Page 668
Creating Drawings
FIGURE 22.18 Creating a block
Summary Annotations and symbols in SolidWorks have many options for connection, creation, and display. Recent releases have brought major improvements to text box–driven annotations. Custom properties and hyperlinks allow the user to populate drawing annotations with content and links to content. Sharing favorites in templates is a great idea for readily available note styles. Blocks have several flexible uses and can be updated from external files across many documents. Their use for simulating mechanisms, piecing together schematics, and annotating drawings, in addition to the Belts and Chains functionality discussed in Chapter 13, make blocks one of the most flexible functions available.
668
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 669
Dimensioning and Tolerancing
I
n years past, dimensioning and tolerancing was an art form and a science. People did, and still do, become very passionate when discussing the right way of performing these tasks. In truth, the techniques are probably not so black and white, but are highly dependent on the industry, the means of manufacture, and the purpose of the drawing. For example, the drawing could be used for quotes, manufacturing, inspection, assembly, testing, and so on, and the drawings for each of these purposes would be somewhat different. While it is important to follow standards and use manufacturing drawing conventions properly, this is not an argument that I want to reignite here. In this chapter, I will focus on how to apply the available tools in SolidWorks.
Putting Dimensions on Drawings Drawings are typically not one of the hotter topics that SolidWorks users become excited about, but a few issues still ignite heated discussions. How to put dimensions onto drawings is one of these topics. This is much like the “tastes great/less filling” debate. Each side of the issue has valid points, and the question is not likely to be resolved any time soon. At the center of this debate is whether the dimensions that you use to create the model should be placed directly on the drawing, or whether a dimensioning scheme specifically for the drawing is better. In the following sections, each method is examined for its benefits and drawbacks.
669
IN THIS CHAPTER Putting dimensions on drawings Dimension options Adding tolerances Using dimension favorites Tutorial: Working with dimensions and tolerances
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 670
Creating Drawings
Insert Model Items Insert Model Items takes all of the dimensions, symbols, annotations, and other elements that are used to create the model, and puts them onto the drawing. Because these dimensions come directly from the sketches and features of the model, they are driving dimensions. This means that they can be double-clicked and changed in the same way that sketch and feature dimensions can be changed, and with the same effect. As a result, changing these dimensions even from the drawing causes the parts and assemblies in which they are used to be changed. You can insert the model items on a per-feature basis, either only bringing the items that are appropriate into the current view, or bringing items into all views. Insertion can be further broken down by type of item, and it can become as specific as pattern counts, Hole Wizard items, specific symbol types, and reference geometry types. You can select Insert ➪ Model Items, or you can access this command from the Annotations toolbar. The Model Items PropertyManager interface is shown in Figure 23.1.
FIGURE 23.1 The Model Items PropertyManager interface
670
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 671
Dimensioning and Tolerancing
Usually, the dimensions need to be rearranged, although SolidWorks does try to arrange them so that they do not overlap. Figure 23.2 shows the result of bringing dimensions into all views for the part. The part is on the CD-ROM in the Chapter 21 materials.
FIGURE 23.2 The default placement of dimensions into all views
Figure 23.2 contains duplicate dimensions, overlapping dimensions, unnecessarily long leaders, radius dimensions pointing to the wrong side of the arc, and a lot of awkward placement. This is what you can expect from using the automatic functions. At best, these dimensions require rearranging, and at worst, they probably require that you delete and replace some of them, or move them to new views where they make more sense. To move a dimension to another view, you can Shift-drag it from one view to the other (make sure that the dimension is appropriate in the destination view). To copy a dimension, you can Ctrl-drag it. If you cannot place the dimension in the view that you have dragged it to, then the cursor will indicate this with a special cursor symbol. If you approach this task by placing dimensions on a per-feature or per-view basis, then that does not change the number of dimensions that you will have to move; it just means that they have to be inserted more often. Keep in mind that if you choose this method, there is a significant amount of cleanup and checking that you must do. The convenience of having the dimensions put into the views for you, and the ability to actually change the model from the drawing are quite useful, but you may not save very much time or effort by doing things this way.
671
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 672
Creating Drawings
Using reference dimensions The alternative to automatically inserting model dimensions is to manually place reference dimensions. At first, this appears to be simply recreating work that has already been done, and this is somewhat true. However, in several important ways, these dimensions are not merely duplicates of the model items. In fact, the reference dimensions that you manually place on the drawing are quite different from the dimensions that are used in the model, unless either the dimensioning scheme of the model or the drawing is changed in some extreme way. The dimensions serve completely different purposes in the two settings, and could only be the same through some odd coincidence. When modeling, I tend to dimension symmetrically, but only on one side, which would not be shown on a manufacturing or inspection drawing. I frequently use workarounds that force a different modeling-dimensioning scheme than I would prefer to use. Often, a feature is located from the midpoint of an edge, which involves no dimensions whatsoever. Sketch entities may have Equal relations, which also leave sketch elements undimensioned. Beyond that, when draft is involved, as is the case with plastic or cast parts, the dimensions of the sketch that you used to create the feature often have little to do with the geometry that is dimensioned on a print for inspection or mold building. Dimension schemes in models reflect the need for the model to react to change, while dimension schemes in drawings reflect the manufacturing or inspection methods, in order to minimize tolerance stack-up, and to reflect the usage of the actual part. Although there are strictly technical reasons for dimensioning drawings independently from the way the model was dimensioned, there are other factors such as time, and the neat and orderly placement of dimensions. Time is an issue because by the time you finish rearranging dimensions that were inserted automatically from the model — checking and eliminating duplicates and then manually adding dimensions that were left out or that had to be eliminated because they were inappropriate for some reason, as well as ensuring that all of the necessary dimensions are on the drawing — it would have been much quicker to manually dimension the drawing correctly the first time using reference dimensions. Inevitably, manually inserting dimensions leads to a different scheme than would be imposed on you by using the Insert Model Items method. It is my opinion that inserting model dimensions into the drawing is in most cases impractical for manufacturing or inspection drawings. This is because of the amount of time required to rearrange and check the dimensions, the need to ensure that you have placed the necessary dimensions, and the simple fact that the dimensioning and sketch relations needed for efficient modeling are usually very different from the dimensioning needed for manufacturing or inspection. It is recommended that you use the manual dimension placement option, which works much in the same way as when dimensions are added to sketches. Dimensions that you place in the drawing in this way are called driven or reference dimensions. Technically, reference dimensions are
672
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 673
Dimensioning and Tolerancing
“extra” dimensions that you place to ease calculations, and you usually create these dimensions with parentheses around them. You can find the setting that controls the parentheses around reference dimensions at Tools ➪ Options ➪ Document Properties ➪ Dimensions ➪ Add Parentheses By Default.
Annotation views Annotation views are views in the model in which annotations have been added. These are generally used by people who are using model dimensions on drawings. Annotation views are accessed from the Annotations folder in the model FeatureManager. They are created automatically when dimensions or notes are added to the part. The annotation view can be used in the model to show the note or dimension in the view in which it was created, or on the drawing to help parse the dimensions into views where they are easily read. Annotation views can be inserted manually or automatically. You can access the settings for annotation views through the RMB menu of the Annotations folder, shown in Figure 23.3.
FIGURE 23.3 The Annotations folder RMB menu
Driven dimension color Driven dimensions on the drawing display in gray, and this can be a problem when the drawing is printed out. There are two methods that you can use to deal with this printing problem. The first method is to set the Page Properties of the drawing to force it to print in black and white. You can find the Page Properties at File ➪ Page Setup. The Page Setup dialog box is shown in Figure 23.4. The second method is to set the color for driven dimensions to black rather than gray. This color setting is found at Tools ➪ Options ➪ Color ➪ Dimensions Non-Imported (Driven).
673
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 674
Creating Drawings
FIGURE 23.4 The Page Setup dialog box
Ordinate and baseline dimensions Ordinate and baseline dimensions are appropriate for collections of linear dimensions when you have a number of items that can all be dimensioned from the same reference. Flat patterns of sheet metal parts often fall into this category. When you apply ordinate dimensions, a zero location is selected first, followed by each entity for which you want a dimension. When dimensions become too tightly packed, SolidWorks automatically jogs the witness lines to space out the dimensions adequately. You can create jogs manually by using the RMB menu. Once you create a set of ordinate dimensions, you can add to the set by selecting Add To Ordinate from the RMB menu. Baseline dimensions are normal linear dimensions that all come from the same reference, and are stacked together at a defined spacing. The default settings for baseline dimensions are found at Tools ➪ Options ➪ Dimensions ➪ Offset Distances. Baseline dimensions work best either when they are horizontal or when the dimension text is aligned with the dimension line (as is the default situation with ISO standard dimensioning). Vertical dimensions where the text is horizontal do not usually stack as neatly because the dimension text runs over the dimension line of the adjacent dimensions.
TIP
Figure 23.5 shows ordinate and baseline dimensions in the same view. You can access ordinate and baseline dimensions from the Dimensions/Relations toolbar (although they are not there by default, you must place them there with the Tools ➪ Customize dialog), or by RMB clicking in a blank space, selecting More Dimensions, and then selecting the type of dimension that you want to use.
674
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 675
Dimensioning and Tolerancing
FIGURE 23.5 Ordinate and baseline dimensions in the same view
Autodimensioning If the Insert Model Items feature is not likely to produce dimensions that are usable in a manufacturing drawing, then the Autodimension feature is even less likely to do so. However, if you use autodimensioning in a controlled way, in the right situations, then it can be a valid way to create selected dimensions. The Autodimension PropertyManager is shown in Figure 23.6. The Autodimension function can fully dimension the geometry in a drawing view. This is best for ordinate or baseline dimensioning where many dimensions are derived from a common reference, as is often the case with sheet metal parts or a plate with many holes drilled in it. You should limit the use of this option to cases where that type of dimensioning is what you would choose, having the choice of all available types of dimensions — do not allow the software to dictate the dimensioning scheme for your drawing. The Autodimension function is different from the Fully Define Sketch function, which is new in SolidWorks 2007. Autodimension works in the drawing, only adding dimensions. Fully Define Sketch works in the model sketch mode, adding dimensions and sketch relations. In previous versions, these functions were consolidated in a single function called Autodimension.
NOTE
675
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 676
Creating Drawings
FIGURE 23.6 The Autodimension PropertyManager interface
Reference sketches For some types of dimensions, you may need to create additional reference sketch entities. For example, with angle dimensions, it may be desirable to add construction lines to help define the angle. You can add centerlines as separate axis-like entities, as discussed in Chapter 22, but you can also sketch in centerlines manually if needed. This type of sketch is most often attached to the view rather than the drawing sheet. Remember that, if necessary, you can create angle dimensions by selecting three points (vertex of the angle first) instead of two lines. When you do this, sketch lines are typically drawn to indicate the vertex of the angle.
TIP
Dimension Options The Dimension PropertyManager contains settings, default overrides, tolerances, favorites, and several other important settings for use with dimensions. The PropertyManager for driven dimensions is shown in Figure 23.7. Favorites and tolerances are covered in their own sections later in this chapter, but the other panels of the Dimension PropertyManager are described in the following paragraphs.
676
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 677
Dimensioning and Tolerancing
FIGURE 23.7 The Dimension PropertyManager interface
Dimension Text The Dimension Text panel enables you to add text to the dimension. You can add lines of text both before and after the dimension value itself, and you can also add text before and after the DIM
677
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 678
Creating Drawings
value on the same line. The DIM field is what places the actual value; if this syntax is somehow deleted, then you can just type it back in and the dimension will still work. The Dimension Text panel includes some formatting tools, such as justification and a setting for the position of the dimension line. The last two rows of buttons include the more commonly used symbols, with access to the complete library, such as any custom symbols that you may have made for the library.
Primary Value Override Among SolidWorks users, one of the biggest and most common mistakes made by former AutoCAD users is the override of dimension values. Apparently due to popular demand, the Primary Value Override is now available in SolidWorks 2007 drawings, in the Dimension PropertyManager as shown in Figure 23.7. This option was added to the software mainly to enable the creation of dimensions with words instead of numbers, as shown in Figure 23.8.
FIGURE 23.8 Using the Override Dimension value
Display Options You can control the default setting for parentheses around driven, or reference, dimensions in Tools ➪ Options ➪ Document Properties ➪ Dimensions ➪ Add Parentheses By Default. The option in the Display Options panel controls the override of the default for the current dimension. Although you can also control dual dimension defaults in Tools ➪ Options, you can turn them on and off from this interface for individual dimensions. When you enable the Dual Dimension option, SolidWorks uses the settings from Tools ➪ Options.
NOTE 678
If it has been a few releases since you examined the Dual Dimension options, then you may find that SolidWorks 2007 has improved placement options for the dual dimensions.
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 679
Dimensioning and Tolerancing
The foreshortened radius is only valid for individual radial dimensions. A foreshortened radius is shown in Figure 23.9. Foreshortened radius dimensions are typically used for large radii when dimensions to the center point are not important. The inspection dimension is shown in Figure 23.9 with an oval around the dimension.
FIGURE 23.9 A foreshortened radius
Witness/Leader Display This panel enables you to set the arrows and dimension lines to be placed inside the witness lines. You can perform this function more easily by using the handles on the arrowheads. From this panel, you can also change the display type of individual arrowheads.
Break Lines When you select the Use Document Gap option in this panel, the witness, or extension, lines of the selected dimension are broken by other crossing dimension lines, witness lines, or arrows. This is shown in Figure 23.10.
Layer Layers are discussed in detail in Chapter 25.
More Properties The More Properties button displays the older Dimension Properties dialog box, which has some duplicate settings, but also contains some less commonly used options that are only available through this interface. Examples of these settings include units, dimension font, control over individual arrow style, and the ability to turn arrows and extension lines on or off. The remaining settings are duplicates of settings in the PropertyManager interface. The Dimension Properties dialog box is shown in Figure 23.11.
679
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 680
Creating Drawings
FIGURE 23.10 Broken witness lines
FIGURE 23.11 The Dimension Properties dialog box
680
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 681
Dimensioning and Tolerancing
Adding Tolerances You can add dimension tolerances in the Dimension PropertyManager, which you can activate by selecting the dimension that you want to modify. Available tolerance types include: n Basic n Bilateral n Limit n Symmetric n MIN n MAX n Fit n Fit with tolerance n Fit (tolerance only)
NOTE
You can also add tolerances to dimensions in models; the tolerance is brought in with the dimension if you use the Insert Model Items feature.
The Tolerance/Precision panel is shown in Figure 23.7. The appropriate number entry fields are activated when you assign the corresponding tolerance type to the dimension. The tolerance types that are available in SolidWorks are shown in Figure 23.12.
FIGURE 23.12 The available tolerance types in SolidWorks
Basic
Symmetrical
Max
Bilateral
Limit
Min Fit Tolerancing
681
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 682
Creating Drawings
Precision In SolidWorks, precision means the number of decimal places with which dimensions are displayed. Typically, SolidWorks works to eight places with meters as the default units. You can create templates that use up to that number of places as the default setting, and then change the number of places for individual dimensions as necessary. The first of the two boxes under Precision is used for the dimension precision, and the second is used for tolerance precision. You can change Precision values for individual dimensions in the PropertyManager for the dimension, and for the entire document at Tools ➪ Options ➪ Document Properties ➪ Units.
Geometric Tolerancing The full range of Geometric Tolerancing symbols are available for control frames, datums, datum targets, and so on. You can use the Geometric Tolerance dialog box to build control frames. This dialog box is shown in Figure 23.13. For commonly used Geometric Tolerance symbols, you may want to create and use favorites.
FIGURE 23.13 The Geometric Tolerance settings
Using Dimension Favorites You can use dimension favorites to apply many items to dimensions. Unlike notes, this is not limited to fonts and formatting. Some of the most common uses of dimension favorites are: n To add standard tolerances to dimensions n To set precision values for dimensions n To add text, such as TYP, to a dimension n To add a commonly used GD&T reference
682
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 683
Dimensioning and Tolerancing
You can save favorites from one document and load them into another document, even between document types. For example, you can load part dimension favorites into a drawing. When an external favorite is updated, any document that it is linked to also updates. In addition, you can break links to external favorites (with the appropriate button on the Favorites panel). Otherwise, dimension favorites have very similar functions to the other types of favorites; the functions of all of the buttons on the Favorites panel are the same.
Tutorial: Working with Dimensions and Tolerances In this tutorial, you can use a single part in several different ways to demonstrate different dimensioning and tolerance functions. Follow these steps to learn more about these topics: 1. Open the part from the CD-ROM called Chapter 23 Tutorial.sldprt. 2. Open the drawing from the CD-ROM called Chapter 23 Drawing.slddrw. 3. Tile the windows using Window ➪ Tile Vertically, and drag the part from the top level of the FeatureManager into the drawing window. This automatically populates the four drawing views. 4. Delete the Top view, leaving the views as shown in Figure 23.14.
FIGURE 23.14 The drawing after step 4
683
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 684
Creating Drawings
5. Click Insert ➪ Model Items, and ensure that the Select All option is selected for Dimensions and Annotations. Also make sure that the Source/Destination drop-down menu is set to Entire Model. Click the green check mark icon and watch the drawing populate. 6. The resulting drawing is quite cluttered. Delete and move dimensions so that the drawing looks like Figure 23.15.
FIGURE 23.15 The drawing after dimensions have been deleted and moved
7. Shift-drag the surface finish symbol to the Right view, and do the same with the 1.900inch dimension. You may have to first Shift-drag it into the other view, and then drag it again to correctly attach or position it. 8. Create a set of horizontal ordinate dimensions from the left end of the part, and dimension the X position of each column of holes. Do the same for rows of holes, using the bottom edge of the Front view as the zero reference. Remember that you can create ordinate dimensions by starting a normal Smart Dimension, then RMB clicking to display the More Dimensions list, and then selecting your choice. 9. If necessary, add center marks and centerlines to the view for clarity. 10. Select the .188 diameter dimension, and in the Dimension Text box, type TYP after the text, and add a bilateral tolerance of +.003, -.005. Save this as a favorite by clicking the Add Favorite icon. 11. Apply the newly created dimension favorite to the R.100 dimension. The results up to this step are shown in Figure 23.16.
684
32_080139 ch23.qxp
3/26/07
5:28 PM
Page 685
Dimensioning and Tolerancing
FIGURE 23.16 Dimensions and tolerances after step 11
12. Make one of the dimension leaders for either the .188 or the R.100 dimensions cross the extension lines of the 4.500 dimension. Then select the 4.500 dimension and in its PropertyManager, select the Use Document Gap option in the Break Lines panel. 13. Place a B datum marker on the circumference of the smaller arc on the left end of the part. Create a Geometric Tolerance control frame, as shown in Figure 23.17.
FIGURE 23.17 Creating a Geometric Tolerance control frame
685
23
32_080139 ch23.qxp
Part V
3/26/07
5:28 PM
Page 686
Creating Drawings
Summary The argument about how to set up and use dimensions on drawings is as old as the process of creating geometrical plans from which objects are built. It is often difficult to separate fact and best practice from opinion. Although I leave it up to you to decide these issues for yourself, this chapter is intended to help you understand how to create the type of drawing that you want. The biggest conflict in this subject arises over whether to place live model dimensions on the drawing or to allow the requirements of the drawing to specify which dimensions are placed where. I am by no means impartial when it comes to this question, but again, you must make the choice for yourself.
686
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 687
Working with Tables and Drawings
S
olidWorks enables you to place several types of tables on drawings, such as the Bill of Materials, or BOM. Design Tables that are used in parts and assemblies can also be shown on the drawing to create a tabulated type drawing. Hole Tables enable you to chart the center locations and sizes of holes for easy access to manufacturing data. Revision Tables can work with PDMWorks or by themselves to help you document the revision history of a drawing. General Tables are also available for any specialized items that are not covered by the other table types.
Driving the Bill of Materials The Bill of Materials, or BOM, is one of the most frequently used types of tables that are available in SolidWorks. BOMs are intended for use with assemblies, but can also be used with individual parts for specialized applications. The types of information that you can expect to see on a BOM are item number, filename, quantity used, description, and any other custom property that you would like to add to it. A typical BOM is shown in Figure 24.1. BOMs are made in one of two ways. The default BOM is made from a special SolidWorks table, while an Excel-based BOM is driven by Excel. While Excel has advantages and disadvantages, many users appear to prefer the default BOM. The reason for this preference is that little is perceived to be given up, except for the stability (crash-worthiness) compared to Excel and the options to keep manual edits. If you plan to use anything other than the standard SolidWorks BOM templates, then you need to make your own BOM templates. If you plan to create either Excel- or SolidWorks table-based templates, then you must choose one of them.
687
IN THIS CHAPTER Driving the Bill of Materials Using Design Tables Using Hole Tables Using Revision Tables Using Gauge Tables and Bend Tables Using Weldment Cut Lists Using General Tables Tutorial: Using BOMs Tutorial: Using Hole Tables Tutorial: Using Revision Tables
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 688
Creating Drawings
FIGURE 24.1 A sample BOM
SolidWorks table-based BOM The BOM shown in Figure 24.1 is a default SolidWorks table-based BOM. The differences between the displays of the two types of BOM are mainly cosmetic; the bigger differences lie in the functionality. The PropertyManager interface for the SolidWorks Bill of Materials is shown in Figure 24.2.
Table-based BOM templates Like other types of data, the SolidWorks table-driven BOM starts from a template. The BOM in Figure 24.1 was created from the default BOM template. When a BOM is initiated, you can select the template in the Table Template panel at the top of the PropertyManager, as shown in Figure 24.2. Table-based BOM templates are created in much the same way that other templates are created: n Specify the settings n Delete the document-specific data n Save the template To save the template, right-click the BOM and select Save As. In the Files of Type drop-down list, select Template (*.sldbomtbt, which stands for “SolidWorks Bill Of Materials Table Template”). Any of the settings, additional columns, links to properties, and so on are saved to the template, and reused when you create a new template from it.
688
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 689
Working with Tables and Drawings
FIGURE 24.2 The PropertyManager for a table-driven BOM
BEST PRACTICE
Put the BOM template in your library area outside of the SolidWorks installation folder. Then identify the path in the Tools ➪ Options ➪ File Locations area.
689
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 690
Creating Drawings
Table Anchor A table anchor locks a corner of the table to a selected point on the format. If no point is selected in the format, then the table is placed at a corner of the sheet. To specify a point in the format to act as the anchor, you must be editing the format (RMB click the sheet and select Edit Sheet Format). Then right-click a sketch endpoint in the format, select Set As Anchor, and specify which type of table the anchor is for. You can set different anchor locations for different types of tables. Figure 24.3 shows the selection and menus for this option.
FIGURE 24.3 Setting a BOM table anchor
TIP
You should save the format and drawing template with these table anchors specified so that you do not need to re-specify them for each new document.
BOM Type As the name suggests, the Top Level Only BOM only shows components on the top level. It treats subassemblies as a single entry. As a result, if the top-level assembly shown on the drawing is made up of five subassemblies and two individual parts, and you select the Top Level Only option, then only seven items are shown in the BOM. The Parts Only BOM ignores subassembly structure, and only displays parts in an unindented list. The Indented Assemblies BOM shows the parts of subassemblies in an indented list under the name of the subassembly. This is the most complete list of SolidWorks documents used because it includes all parts and assemblies.
690
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 691
Working with Tables and Drawings
The Show Numbering option for indented assemblies is only activated after the Indented Assemblies option is checked, and you have placed the table. When you use this option, it causes subassembly parts to be numbered with an X.Y number system. For example, if item number 4 is a subassembly, and it has three parts, then those parts receive the item numbers 4.1, 4.2, and 4.3.
Configurations The Configurations panel of the BOM PropertyManager displays slightly differently for Top Level Only BOMs compared to the other types. The Top Level Only BOM type enables the option to show multiple assembly configs and display the quantities for top-level components in separate columns, as shown in Figure 24.4. This figure shows that the configuration named “D” has some suppressed parts, including some parts that are now not used in the “D” configuration, and that therefore have a zero quantity. Notice the available options for dealing with zero-quantity parts.
FIGURE 24.4 Configuration options with the BOM
Keep Missing Items When you are making changes to a model, parts are often either suppressed or deleted altogether. Some company documentation standards require that parts that are removed from a Bill of Materials remain on the bill, and display with strikethrough formatting, although this may be a relic from days gone by when it was more difficult to remove items from hand drawings.
691
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 692
Creating Drawings
Zero Quantity Display The Zero Quantity Display settings are only used for configurations where some components are not used in some configurations. The three options that are available are: n Quantity Of Dash: Substitutes a dash for the quantity value n Quantity Of Zero: Uses a zero for the quantity value n Blank: Quantity value is blank
Item Numbers Item numbers for components listed in the BOM can start at a specific number and be given a particular interval. The Do Not Change Item Numbers option means that even when rows are reordered, item numbers stay with their original components. The Follow Assembly Order option, which is also available through the RMB menu, means that the order of the components in the BOM follows the order of the components in the Assembly FeatureManager. If the order is changed in the assembly, it also updates in the drawing.
BOM Contents The BOM Contents button at the bottom of the Bill of Materials PropertyManager opens the dialog box shown in Figure 24.5. This dialog box enables you to reorder as well as hide or show rows of the BOM. If you created the BOM using the Indented Assemblies option, then assemblies can also be expanded and collapsed from this interface.
FIGURE 24.5 The BOM Contents interface
692
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 693
Working with Tables and Drawings
You can also group and ungroup components in this interface, to reorder them as a group that is handled differently from the way that a subassembly is handled.
Table Format Below the BOM Contents button is a button that allows you to access the Table PropertyManager. The Table PropertyManager interface is shown in Figure 24.6. The options in this interface are selfexplanatory, and help you to visually format the table.
FIGURE 24.6 The Table PropertyManager interface
Controlling the appearance of the Table-based BOM If you are already familiar with formatting an Excel-based BOM, then it may take some getting used to formatting the SolidWorks table-based BOM. Figures 24.7 and 24.8 show some of the cursor feedback and selection methods for selecting a column, a row, and a single cell, and moving the entire table.
693
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 694
Creating Drawings
FIGURE 24.7 Selecting a column, row, cell, and table
To move the table, click above and to the left of the upper-left corner and drag the table to a new location. When the table is selected, a border appears around the table that is not normally visible, and is not printed with the drawing. You can change the properties of a row or a column by selecting just outside of the row or column to the top or the left. You can establish spacing and width of rows or columns by dragging with the split cursor shown in Figure 24.7 or by typing a value for the column width in the Column Properties panel.
Adding rows or columns To add a column, right-click near where you want to add the column, and select Insert. Then select whether you are adding a row or a column, and whether you are placing it above or below where you right-clicked. If the column goes in the wrong location, then you can move it by selecting the column and using the arrows in the Column Properties panel to move it left or right.
694
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 695
Working with Tables and Drawings
FIGURE 24.8 Column, Row, and Cell properties
The next thing you will want to do with a column is to assign what kind of data goes into the column. You can use a custom property such as Part Weight or Vendor, as shown in the Column Properties panel in Figure 24.8. The Title box in the panel enables you to put a header at the top of the column. You can also use equations in the SolidWorks table-driven BOM. If the Custom Property option is checked in the Column Properties panel, then a custom property can be selected to populate the cells of that column for each part in the assembly.
NOTE
If you create a BOM with the columns and properties that you like, then you can save it to a template as described earlier in this chapter.
Excel-based BOM In previous releases, the Excel-based BOM was the only way to add a BOM to a drawing. This feature has been replaced in most respects by the table-driven BOM, but many people still use the Excel-based BOM either out of habit or to comply with legacy standards. Figure 24.9 shows the interface for the Excel-based BOM. Unless you have a compelling reason to do otherwise, I recommend that you use the SolidWorks table-based BOM, as it is the function that will be best supported in future versions of SolidWorks software.
BEST PRACTICE
695
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 696
Creating Drawings
FIGURE 24.9 The interface for Excel-based BOMs
Using Design Tables Design Tables that are used to drive configurations of parts and assemblies can be shown on the drawing. This is often called a tabulated drawing, and is typical of parts that have a basic shape that is common among several sizes or versions of the part. The sizes are shown by a symbol on the drawing, with a column headed by that symbol showing the available dimensions and the corresponding size (configuration) names. You can insert a Design Table into a drawing by selecting Insert ➪ Tables ➪ Design Table or through the Design Table button on the Tables toolbar. In either case, you must pre-select a drawing view of a part or assembly that contains a Design Table before the menu selection or toolbar button become activated. Design Tables that are displayed in this way are often formatted visually to some extent. It is necessary to hide columns and rows unless you want the dimension or feature name syntax to display
696
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 697
Working with Tables and Drawings
on the drawing as well as the values. Extra columns and rows are often added to make the design table readable. The image to the left in Figure 24.10 shows a design table that is formatted to be placed on a drawing. The image to the right shows the same design table with all of the information shown. The first column and the first row are hidden to make the table more readable on the drawing, and the second column and second row use the $user_notes header to format the names.
FIGURE 24.10 A design table prepared to be placed on a drawing
Figure 24.11 shows the drawing with the table inserted. To display the table properly, you have to edit the table in the window of the parent document and adjust the border of the table to be exactly how you want it to appear on the drawing. The adjusted table is shown in Figure 24.11. The labeled dimensions were created by simply making reference dimensions and overwriting the value in the Dimension Text panel of the Dimension PropertyManager. If you would like to examine this data more closely, the drawing and part are included on the CD-ROM. The drawing is named Chapter 24 – DT.slddrw. This drawing uses a part Design Table, but you can also place assembly Design Tables onto the drawing. This type of drawing is often called a tabulated drawing.
697
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 698
Creating Drawings
FIGURE 24.11 A drawing with the Design Table inserted
If you need to place something on your drawing such as a Design Table, but it does not appear that the Design Table is going to meet your needs, then you may want to simply copy the data out of the Design Table and recreate it in a static Excel spreadsheet. The Design Table that you place on the drawing updates if it is changed in the part or assembly, just like the drawing geometry, but you must manually update an Excel spreadsheet that is created from copied data. Again, you must answer the question about whether the automatic functions make up for the cost of setting them up to work for you. In many cases they do, but in other cases they require more work than they save.
Using Hole Tables You can place Hole Tables on drawings to include information such as the size, position, and number of holes of a given size on a drawing. Only circular holes are recognized, although they do not have to be Hole Wizard or simple hole features. The position is given relative to a selected reference position, and the holes are labeled. Like other table types, Hole Tables can use templates. As with other templates, you should locate Hole Table templates in a library area outside of your local SolidWorks installation folder. You can then direct SolidWorks to this location using the path settings at Tools ➪ Options ➪ File Locations.
698
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 699
Working with Tables and Drawings
Hole Tables use anchors in exactly the same way as BOMs. For more information, see the Table Anchors subsection in the Bill of Materials section earlier in this chapter. You can find the options for hole tables at Tools ➪ Options ➪ Document Properties ➪ Tables. These settings are discussed in detail in Appendix B. Figure 24.12 shows the PropertyManager for a hole table. Figure 24.13 shows the resulting Hole Table on a drawing with a part that contains holes. The table incorporates holes from multiple views, using a different zero reference for each view.
FIGURE 24.12 The PropertyManager for the Hole Table
To initiate the Hole Table function, you must first select a view. You can access the Hole Table function through Insert ➪ Table ➪ Hole Table. To specify the datum, either select an edge in each direction to serve as the zero mark for the X and Y directions, or select a vertex or point to serve as the Origin in both directions.
699
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 700
Creating Drawings
FIGURE 24.13 A Hole Table combining holes in different views
To select the holes to be included in the table, activate the Holes panel selection box, and either select the hole edges directly, or select the faces on which the holes are located. Once you place the table, you can add holes or change the datum information. To do this, use the RMB menu of the Hole Table entry in the Drawing FeatureManager, and select Edit Feature. The RMB menu is shown in the middle image of Figure 24.12. If you simply select a Hole Table that has already been created, the Properties interface displays, as shown in the top-right image. You can resize columns and rows in the same way as for BOM tables. In the table in Figure 24.13, the Combine Same Sizes option is used, which causes several of the cells of the table to merge. If you use the Combine Same Tags option, then the hole locations are not displayed — only the hole callout description and the quantity appear. Figure 24.14 shows this arrangement.
FIGURE 24.14 The Combine Same Tags option used with a Hole Table
700
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 701
Working with Tables and Drawings
You can control the hole callout description used in Figure 24.14 by using the file named calloutformat.txt, which is found in the lang\english subdirectory of the SolidWorks installation directory. Again, if you customize this file, then you should keep it in a library external to the installation directory and list it in the Tools ➪ Options ➪ File Locations area. This text file enables you to specify how hole callouts are specified for different types of holes.
Using Revision Tables Revision Tables in SolidWorks can be used in conjunction with PDMWorks Workgroup, but this integration goes beyond the scope of this book. The Revision Table uses a Table Anchor, which is used in exactly the same way as the BOM table. Revision Tables also use templates in the same way as the other table types, and it is recommended to move customized templates to a library location and specify the location in Tools ➪ Options ➪ File Locations. Figure 24.15 shows the Revision Table PropertyManager interface where you can create and control the settings for the table. You can find the default settings for Revision Tables at Tools ➪ Options ➪ Document Properties ➪ Tables. These settings are described in more detail in Appendix B. The image in the upper left of Figure 24.15 is the PropertyManager interface that displays when you initially create the Revision Table, and the rest of the Figure 24.15 images are for editing or adjusting the table. The properties for columns, rows, and cells can be controlled in much the same way as other table types. You can initiate the Revision Table function through the menus or the Tables toolbar. However, this function simply creates the table, it does not populate it. You must set the table anchor in the format in order for the Table Anchor to work. Additional columns may be added or formatted to accept other data. Once you have created the columns or formatting, you can save the changes to a template, which is also available through the RMB menu. You can add a revision to the table by right-clicking the table and selecting Revisions ➪ Add Revision. The settings for Revision Tables are controlled through Tools ➪ Options ➪ Document Properties ➪ Tables. These settings are shown in detail in Appendix B. This includes control over whether the revision uses numerical or alphabetical revision levels, but does not provide for more complex revisioning schemes.
701
24
33_080139 ch24.qxp
Part V
3/26/07
5:29 PM
Page 702
Creating Drawings
FIGURE 24.15 The Revision Table PropertyManager interface
Immediately after you have created the revision, if the option is enabled, you are prompted to place a balloon that contains the revision level to identify what has been changed. To finish placing symbols, you can press Esc or click the green check mark icon in the Confirmation Corner or the
702
33_080139 ch24.qxp
3/26/07
5:29 PM
Page 703
Working with Tables and Drawings
PropertyManager. When you are finished placing the balloons, you can fill in the description of the revision by double-clicking in the Description cell where you want to add text. Figure 24.16 shows a Revision Table with balloon symbols placed on the drawing.
FIGURE 24.16 A Revision Table with balloon symbols
Revision Tables work by creating a Revision custom property in the drawing document, and by incrementing this revision each time a revision is added to the table. Additional columns that are linked to custom properties can be added to Revision Tables and Revision Table templates.
Using Gauge Tables and Bend Tables Gauge Tables and Bend Tables are specific to sheet metal parts, and are covered in detail in Chapters 29 and 30.
Using Weldment Cut List Tables Weldment Cut Lists are a special type of table that closely resembles a BOM table in many ways. These are discussed in Chapter 31, which covers Weldments.
703
24
33_080139 ch24.qxp
Part V
3/26/07
5:30 PM
Page 704
Creating Drawings
Using General Tables General Tables can be used for any type of tabulated data. Column headers can be filled with either text labels or custom property links. Regular Excel OLE objects can also be used for the same purpose, and depending on the application, you may prefer this. The General Table uses the filename extension, *.sldtbt. It can be created without a template, as a simple block of four empty cells, or you can use a template that has a set of pre-created headers.
Tutorials: Using Tables Rather than having tutorials for every table type, this chapter has tutorials only for the BOM, Hole Table, and Revision Table. The skills used with these types are transferable to the other types.
Using BOMs This tutorial guides you through the steps that are necessary to prepare an assembly for the drawing and BOM. Configurations and custom properties are used in this example. Remember that if a drawing view is cross-hatched and you cannot see the geometry, then you may have to press Ctrl+Q to rebuild it. Follow these steps: 1. Begin this tutorial with SolidWorks closed and Windows Explorer open. 2. If you have not already done so, create a folder for a library that is not in your SolidWorks installation folder. Call it D:\Library\ or something similar. Make a folder inside this folder called Drawing Templates. Copy the file from the CD-ROM named inch B.drwdot to this new folder. 3. Launch SolidWorks and go to Tools ➪ Options ➪ File Locations ➪ Document Template. Click the Add button and add the new library path to the list. Shut down SolidWorks and restart it. 4. Open the assembly Chapter 24 – BOM Assy.sldasm from the CD-ROM. 5. Using the Make Drawing From Part/Assembly button, make a new drawing of the assembly from the drawing template. 6. Delete the isometric view, and in its place make a new drawing view using the named model view “exploded.” 7. Edit the sheet format. Right-click the sketch point at the location indicated in Figure 24.17. In the pop-up menu that appears, select Set As Anchor and then select Bill of Materials.
704
33_080139 ch24.qxp
3/26/07
5:30 PM
Page 705
Working with Tables and Drawings
FIGURE 24.17 Setting the Table Anchor
RMB on this point
8. Exit Edit Sheet Format mode by selecting Edit Sheet from the RMB menu. 9. Select the new view and click Insert ➪ Table ➪ Bill of Materials, or click the Bill of Materials button from the Tables toolbar. Use the default selections, except in the panels shown in Figure 24.18. 10. Click inside the exploded view, but off of any part geometry, and then select the Autoballoon tool from the Annotations toolbar. Toggle through the available options to see whether any of the possible autoballoon configurations meets your needs. If not, use the standard Balloon tool to select the part and place the balloon. This gives you more control over the attachment points and placement of the balloons.
705
24
33_080139 ch24.qxp
Part V
3/26/07
5:30 PM
Page 706
Creating Drawings
FIGURE 24.18 Creating the Bill of Materials
11. Change the balloon for the short pin to be a circular split-line balloon (do this by clicking the balloon, and then switching the style in the PropertyManager). Notice that the quantity appears in the bottom of the balloon. The drawing view and the BOM should now look like Figure 24.19. 12. Notice that several of the parts use a default description of “description.” Edit each of these parts by right-clicking the part’s row in the BOM table and selecting Open from the menu. Change the custom property called Description in each part. Keep in mind that this may be handled differently for configured parts.
NEW FEATURE
New in SolidWorks 2007 is the ability to open a part directly from its entry in the BOM.
13. The Bracket part is listed twice using the configuration name because of the way the configurations are set up for the parts. To list the bracket only once using the filename, open the bracket, RMB click one of the configuration names in the ConfigurationManager, and select Properties. In the Bill of Materials Options panel, select Document Name from the drop-down list. Do this for the other configuration, as well.
Notice also that the Description field holds the configuration-specific custom property for Description, which is used in the BOM.
706
33_080139 ch24.qxp
3/26/07
5:30 PM
Page 707
Working with Tables and Drawings
FIGURE 24.19 The drawing view and the BOM after step 11
14. Toggle back to the drawing (using Ctrl+Tab), select anywhere on the BOM table, and then select Table Properties from the PropertyManager. Expand the Part Configuration Grouping panel, and select the Display All Configurations Of The Same Part As One Item option. This changes how the bracket displays, as well as the pins. 15. In this step, you will add a column to the BOM that calls on an existing custom property that is already in all of the parts. Place the cursor over the last column on the right and RMB click it. Select Insert ➪ Column Right. This places a new column to the right of the last one and displays the Column Properties panel of the Insert Column Right PropertyManager, as shown in Figure 24.20. 16. In the first drop-down selection box, select the Weight custom property. Click the green check mark icon to accept the changes. 17. The BOM with the additional column can be saved as a BOM template by right-clicking anywhere in the BOM and selecting Save As. You can then set the type to a BOM template, and the directory to the library location for BOM templates.
If you would like to compare your results against mine, the finished drawing is called Chapter 24 – BOM Tutorial Finished.slddrw.
707
24
33_080139 ch24.qxp
Part V
3/26/07
5:30 PM
Page 708
Creating Drawings
FIGURE 24.20 Adding a column to the BOM
Using Hole Tables This tutorial guides you through the creation and setting changes that are common in SolidWorks Hole Tables. The part for this tutorial is the part from which the figures for the section on Hole Tables were made. Follow these steps: 1. Create a new drawing from the template that was used for the BOM tutorial. If you have not done the BOM tutorial, then move the drawing template named inchB.drwdot from the Chapter 24 materials on the CD-ROM to your library location for drawing templates. Then create the drawing from the template. 2. Click the Model View button on the Drawings toolbar, and browse to the part named Chapter 24 – Hole Table Part.sldprt. 3. Place a Front view and project a Left view and an isometric view. Then press Esc to quit the command. Finally, delete the four predefined views. 4. There is not an anchor in this template for a Hole Table. If you would like to create one, this would be a good time to do so. Follow the steps in the BOM tutorial for specifying the anchor point. 5. From the Tables toolbar, click the Hole Table button. 6. Figure 24.21 shows a section of the Hole Table PropertyManager with the selections that you need to make for this Hole Table. 7. Once you have completed the selections, press the Next View button at the bottom of the PropertyManager, and make similar selections in the Left view. The holes for both views are added to a single Hole Table.
708
33_080139 ch24.qxp
3/26/07
5:30 PM
Page 709
Working with Tables and Drawings
FIGURE 24.21 The Hole Table PropertyManager and selections
Select these two faces to go into the Edges/Faces box Select this vertex to go into the Origin box
8. The table is created using the default settings established in Tools ➪ Options ➪ Document Properties ➪ Tables, but you can change them here for this specific table. Click anywhere in the table, and then select Table Properties at the bottom of the PropertyManager. Changing from numerical to alphabetical assigns a letter to each hole type, and a number to each instance of the type. Make this change and update the table. Figure 24.22 shows the table before and after the changes.
FIGURE 24.22 Using numerical and alphabetical hole tag identification
709
24
33_080139 ch24.qxp
Part V
3/26/07
5:30 PM
Page 710
Creating Drawings
9. Change the number of decimal places used in the Hole Table from two places to three. You can do this in the Table Properties window, in the Hole Location Precision panel. 10. Deselect the Hide Hole Centers option in the Visibility panel.
Using Revision Tables In this tutorial, you create a basic Revision Table, and make a template. Follow these steps: 1. Using a drawing that you completed in one of the previous tutorials, make sure that a Revision Table Anchor has been placed in the upper-right corner of the Sheet Format. You must edit the Sheet Format to do this by RMB clicking the point that you want to use for the anchor. Remember to select Edit Sheet from the RMB menu to exit Edit Sheet Format mode.
NOTE
Ideally, the anchors for all table types should be set in templates and formats, but here it is set up to ensure that you get some practice with creating the anchors.
2. Click the Revision Table button on the Tables toolbar. Be sure to select the upper-right corner that you want to be anchored, and select the Attach to Anchor option in the PropertyManager. Click the green check mark icon to accept the table. Figure 24.23 shows the initial stub of the Revision Table.
FIGURE 24.23 The initial stub of the Revision Table
TIP
Drawing templates can be saved with the Revision Table stub if it also has a format. The revision table is not saved with the format because it has to go on the drawing sheet.
3. To initiate a new revision level in the Revision Table, RMB click the table and select Revisions ➪ Add Revision. 4. Depending on the default settings in Tools ➪ Options ➪ Document Properties ➪ Tables, the first revision will be either A or 1. If you are using PDMWorks Workgroup, then you may have other options. 5. Depending on your options settings, you may immediately be prompted to place a balloon that contains the new revision level. You can place balloons with or without leaders. The balloons are meant to indicate areas of the drawing that are affected by the revision. Press Esc or click the green check mark icon when you are finished placing the balloons.
710
33_080139 ch24.qxp
3/26/07
5:30 PM
Page 711
Working with Tables and Drawings
You may want to be careful using balloons on assembly drawings or other drawings that already have balloons that are used for other purposes. For this reason, it may be a good idea to use a distinctively shaped balloon for Revision Tables.
NOTE
6. To add text to the Description field, simply double-click in the field and start typing. The text automatically wraps to fit the box. 7. Practice by adding a couple of revisions, balloons, and descriptions. 8. After you have added a couple of revisions, check the custom properties by going to File ➪ Properties ➪ Custom. Notice that a revision property has been added, and the latest revision is represented by the value of the custom property. The number of revisions kept in the Revision Table is no longer an option as it was in previous releases, but in its place you can now control how revision tables interact with multiple sheets. For more information, see Appendix B.
NOTE
9. You can add columns in the same way that they were added to the BOM. You can merge and unmerge cells, and link properties to cells. With the cursor over the last column (Approved), RMB click and select Insert ➪ Column Left. In the Column Properties, select Custom, and from the Properties drop-down menu, select DrawnBy. Accept the changes by clicking the green check mark icon. 10. Save the template by right-clicking anywhere in the Revision Table and selecting Save As ➪ Rev Table Templates. Then save it to the appropriate location outside of the SolidWorks installation directory.
Summary SolidWorks enables you to work with both tables that are highly specialized for particular uses, and the General Table, which is available for any type of tabulated data. The most frequently used types are BOMs, Hole Tables, and Revision Tables. Design tables that drive part and assembly configurations can also be placed on a 2D drawing, but in these cases, some formatting is usually necessary to make the Design Table presentable and the information on it easy to read. Other types of tables, such as Gauge and Bend tables and Weldment Cut Lists, are specialized for sheet metal and weldment parts, respectively, and are discussed in chapters that cover those topics.
711
24
33_080139 ch24.qxp
3/26/07
5:30 PM
Page 712
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 713
Using Layers, Line Fonts, and Colors
M
ost SolidWorks users have used AutoCAD at some point in their careers. AutoCAD is the Microsoft of CAD. Regardless of what you think of the company, the software, or the 2D world in general, AutoCAD has left its mark on CAD users of all kinds in the form of certain default expectations that people have about CAD software. A few common preconceptions are that layers, the Command Line, paper space/model space, and printing should be really difficult. Given the ubiquity of AutoCAD in the market, it is not surprising that a few AutoCAD-like functions have found their way into the SolidWorks software. SolidWorks users, and even the SolidWorks Corporation, become a little defensive when you start talking about AutoCAD, or AutoCAD-like functionality. Maybe that is because we consider ourselves more highly evolved, having understood that 3D parametric design is a more sophisticated plane of existence than flatland 2D design. When former AutoCAD users make the switch to SolidWorks, the questions start: Where is the Command Line, How do I put parts on layers, How do I change the background color to black, and my personal favorite, Where is the zero-radius trim? This chapter addresses a couple of AutoCAD-like functions in the SolidWorks drawing environment. The goal is not to make the functions look or work or compare in any way to AutoCAD, but to simply to make them useful in the context of SolidWorks.
713
IN THIS CHAPTER Controlling layers Controlling line format Hiding and showing edges Tutorial: Using drawing display tools
34_080139 ch25.qxp
Part V
3/26/07
5:30 PM
Page 714
Creating Drawings
Controlling Layers Layers are arguably one of the most visible differences between AutoCAD and SolidWorks. Layers are not available in SolidWorks 3D modeling at all — only in the 2D drawing environment — and even there, they do not see a lot of use. However, this is not to say that there is no need for them.
Layers in imported 2D data When you import data through DXF or DWG format files, the layers that exist in the original data are brought forward into SolidWorks, and you can use them in a similar way to the original AutoCAD usage. For example, you can turn layers on or off (visible or hidden), and you can change layer names, descriptions, color, line thickness, and line style. The way you intend to use the imported data determines how you should open the file. If you only intend to view and print the drawing, then I would suggest using DWG Editor, which is installed with SolidWorks and enables you to do almost anything you can do with basic AutoCAD. It also has the advantage of having a familiar interface for the AutoCAD user (it even has a black background!). DWG Editor is available from the Start menu, by selecting Programs ➪ SolidWorks ➪ DWG Editor. If you need to integrate data from the imported document into a native SolidWorks drawing, then you can open the DWG file from the normal Open dialog box in SolidWorks. If you want to make a 3D part from the 2D data in the DWG file, then you may want to import the drawing into the part sketch environment. This usually leads to some speed issues. If you prefer, sketch entities can also be copied from the drawing to the model sketch. You can even copy entities from DWG Editor to the SolidWorks part sketch. The sketch needs to be open in order to paste the sketch entities. In the case where imported 2D data is brought into the model sketch, you lose all of the layer information, because part and assembly documents do not allow layers.
TIP
The colors assigned to layers are often based on a black background, and so they can be difficult to see on a white background. The two ways of dealing with this are to change the SolidWorks drawing sheet color to something dark or to change the individual layer colors to something dark. Either method is easy, although if you have to send the 2D data back to its source, it may be best to temporarily change the drawing sheet color. Figure 25.1 shows the layer interface with an imported drawing in the background. The colors have been changed here to improve visibility. The Layers dialog box is activated by the Layer Properties toolbar button, which is found on both the Layer and Line Format toolbars. Be aware that many items in an imported drawing may come into SolidWorks as blocks. These items may need to be exploded before you can work with them. This is often the case with the drawing border, title block, or format.
714
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 715
Using Layers, Line Fonts, and Colors
FIGURE 25.1 The Layers dialog box and the Layer toolbar
Layers on the sheet format One of the most obvious uses of layers is on the sheet format. The sketch lines used to create the border often have a heavier line weight and a different color that easily distinguishes them from model geometry. You can assign layers in one of three ways: n Select existing items, and then select a layer from the drop-down list on the Layer toolbar. n Set the active layer and create new items. n While creating items such as sketch entities and annotations, select the layer for the new entity directly from the PropertyManager. To set a layer to the active layer, double-click it from the Layers dialog box, as shown in Figure 25.1, or change it from the drop-down list on the Layer toolbar. When you assign an active layer, other newly created entities are also placed on the layer, not just sketch entities. Symbols, annotations, blocks, and other elements can also be put onto layers. If you are not particular about the layering scheme on a drawing, then it may be advisable to set the active layer to None, which is a valid option in the Layer toolbar drop-down list. Another option when building a sheet format, or any other drawing function that requires sketching, is to use a special layer for construction geometry. This enables you to hide the layer when it is not being used, but it still maintains its relations. Hidden layers can be used in several other ways, for example, as standard notes on the drawing, and they can be easily turned on or off.
715
25
34_080139 ch25.qxp
Part V
3/26/07
5:30 PM
Page 716
Creating Drawings
Dimensions and notes on layers SolidWorks drawings have a tendency to be drab black-and-white drawings, in contrast to AutoCAD drawings, which often seem to take on a plethora of contrasting colors. Still, drawings do seem a little easier to comprehend when different types of items are colored differently, but in order for this to work, you must apply the coloring scheme consistently. Dimensions and annotations can also be placed on layers in the three ways described in the previous section (active layer, from the PropertyManager during creation, and through the drop-down list on the Layer toolbar). However, the line styles do not affect dimensions and notes, only the color and visibility settings.
Components on layers Assembly drawings probably suffer the most from the monochromatic nature of most SolidWorks drawings because individual components can be difficult to identify when everything is the same color. This is why SolidWorks users typically color parts in the shaded model assembly window. It only makes sense that as users, we would want to do the same thing on the drawing. An intuitive and easy workaround for this problem would seem to be to simply turn the drawing view to a wireframe mode in the same way that changing a drawing view to a shaded mode shows the parts in color. Unfortunately, wireframe on drawings always defaults to black edges. Even if you set a Display State using some wireframe parts where the wireframe displays in the same color as the shaded part in the assembly window, this still appears in black and white on the drawing. All that is left to display the components of an assembly in different colors while using a wireframe display mode is to set the Component Line Font options. (Line Fonts are covered in the next section.) The Component Line Font dialog box contains a Layer setting, which you can use to put a part on a layer. If the layer is set up with a color, then the part displays with that color in all views of the drawing, or in just the current view, depending on your settings. While it does take a little time to set up the individual layers for each part and then to set the parts to the layers, it is better than the alternative, which is to do nothing. You can access the Component Line Font dialog box by right-clicking a component in a drawing view. The Component Line Font dialog box is shown in Figure 25.2. In normal use, the Use Document Defaults option is selected and all of the settings in the dialog box are grayed out. To gain access to these settings, you must deselect the Use Document Defaults option, as shown in Figure 25.2.
716
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 717
Using Layers, Line Fonts, and Colors
FIGURE 25.2 The Component Line Font dialog box
Controlling Line Format The Line Format feature is composed of three different settings, Line Color, Line Thickness, and Line Style. These settings can be controlled separately from layers, and so they can be used in model sketches as well as on drawings. In the model, the line font can only be displayed for inactive sketches. Any sketch that is both closed and shown can be displayed with the Line Format settings.
CROSS-REF
For more information on using line styles in the model, see Chapter 6.
Figure 25.3 shows the Line Format toolbar along with the interfaces for Line Color, Line Thickness, and Line Style.
FIGURE 25.3 The Line Format toolbar and related interface options
717
25
34_080139 ch25.qxp
Part V
3/26/07
5:30 PM
Page 718
Creating Drawings
The term line font refers to a combination of style, end cap, and thickness. Line fonts are set in the document-specific settings at Tools ➪ Options ➪ Document Properties ➪ Line Font. These settings are described in detail in Appendix B.
NOTE
Using the Line Format settings You can specify the Line Format settings using two different methods. In the first method, you can set them with nothing selected, in which case they function like System Options (the new setting takes effect for all documents that are opened on the current computer). In the second method, if they are set with sketch entities or edges selected, then the settings apply only for the selected entities.
CAUTION
If you change these settings with nothing selected, then the Line Format settings for color, thickness, and style function as system options.
End Cap Style Another option for the Line Font settings is the End Cap Style. This offers an important option, especially for thick lines. The three options are flat, round, and square, although the square style is usually appropriate. In the past, flat was the default setting, and there were no other options.
NEW FEATURE
The End Cap Style settings in Tools ➪ Options are new for SolidWorks 2007.
Figure 25.4 shows the difference between the three options of End Cap Style.
FIGURE 25.4 The End Cap Style setting options
Line Thickness settings The Line Thickness settings are thin, normal, thick, and thick (2) to (6). Figure 25.5 shows the Line Weights dialog box, and the Print dialog box. This is an area where the Help file will not only be little actual help, but may also steer you in the wrong direction. The Help does not appear to point to a location where you can set up the actual dimensional widths of printed lines assigned to the 9 thicknesses. The easiest to find direct mention of “line thickness” points to an obscure PhotoWorks setting. Other mentions of “line thickness” point to either the Layers or Line Format functions. The correct information in the help is cleverly hidden, listed under “lines, weights.” The settings for the line widths used to be on the Page Setup dialog box — the help for Page Setup still has a
718
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 719
Using Layers, Line Fonts, and Colors
line thickness entry, even though the setting is no longer found there — but are now found in the Print dialog box. Figure 25.5 shows the Print dialog box and the Line Weights dialog box.
FIGURE 25.5 The Line Weights settings in the Print dialog box
The Line Weights settings are system options, and are not document-specific. As a result, if drawings are printed from two different computers, and one of them has been customized, then the drawings may look different.
CAUTION
Line Style setting You can create custom line styles using the syntax shown on the Tools, Options, Document Properties, Line Style page. This is a document-specific setting, and so if you make a custom line style and want to use it in another document, then you have to save it out (as a *.sldlin file) and load it into the other document. Also, if you save your templates with this line style loaded, then you will not have to load the styles for any document made from that template. For more information about line styles, see Appendix B.
Color Display mode Color Display mode toggles between the display of assigned colors and sketch colors. This is primarily used in drawings when you are making sketches where sketch relations are important.
719
25
34_080139 ch25.qxp
Part V
3/26/07
5:30 PM
Page 720
Creating Drawings
Hiding and Showing Edges Sometimes, for illustrative purposes, it is desirable to hide certain edges in drawing views. The Hide Edge and Show Edge toolbar buttons are associated with the Line Format toolbar, although they may not be on the toolbar by default. You can use Tools ➪ Customize to put them on a toolbar. To use the Hide Edge tool, simply select the edges that you would like to hide, and click the Hide Edge toolbar button. To show the edges, click the Show Edge toolbar button; the cursor will now be able to select the hidden edges.
Tutorial: Using Drawing Display Tools Some of the functions described in this chapter are difficult to understand until you actually use them. This tutorial guides you through the functions step by step so that you can see them in action. Start here: 1. From the CD-ROM, open the drawing called Chapter 25 – Tutorial.slddrw. Make sure that the Layer and Line Format toolbars are active and that the Hide Edge and Show Edge buttons are available on the Line Format toolbar. 2. RMB click a blank space and select Edit Sheet Format from the menu. 3. Window-select everything on the format and use the drop-down list on the Layers toolbar to assign the selection to the Border layer. Notice that this changes the color and the thickness of the sketch lines.
NOTE
Selection filters are inactive when you are editing drawings or formats; they are active only at odd times, such as when you edit a note.
4. RMB click a blank space and select Edit Sheet. 5. Click the Layer Properties button on either the Layer or Line Format toolbar. Add new layers for each of the part groups, bracket, clevis, pins, and blocks, assigning different colors to each layer. Figure 25.6 shows the Layers dialog box with these layers created.
FIGURE 25.6 The Layers dialog box
720
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 721
Using Layers, Line Fonts, and Colors
Be aware that creating new layers leaves the last layer that you created active, as indicated by the yellow arrow in Figure 25.6. There is no way to set the active layer to None from the Layers dialog box, and so this has to be done using the drop-down list in the Layer toolbar.
CAUTION
6. Set the active layer to None in the Layer toolbar drop-down list. 7. RMB click the Bracket part in one of the views and select Component Line Font. Deselect the Use Document Defaults option, and select the Bracket layer from the drop-down list in the lower-right corner of the dialog box, as shown in Figure 25.7. Make sure that the Drawing View option is set to All Views.
FIGURE 25.7 The Component Line Font dialog box
8. Repeat Step 7 for all of the components, assigning each component to its own layer. Notice how this makes the parts easier to identify. Alternatively, you could simply change the line style and weight (thickness — note the terminology inconsistencies here) for each component. This saves you creating the layers, but you lose the color settings.
NOTE
9. Open the Component Line Font dialog box for the Bracket part again. This time, set the Line Weight to Thick (6), and then click OK. You may have to rebuild the drawing to show the change (Ctrl+B or Ctrl+Q). Figure 25.8 shows a detail of the corners that are created by the thick lines. Notice the notches created at the corners.
721
25
34_080139 ch25.qxp
Part V
3/26/07
5:30 PM
Page 722
Creating Drawings
FIGURE 25.8 Applying thick edges
10. These notches are supposed to be fixed using a new setting in SolidWorks 2007. In the menus, go to Tools ➪ Options ➪ Document Properties ➪ Line Font, and set the End Cap Style to Square. Click OK to exit the Document Properties. In the drawing, select inside the view where you are working, and make sure that it is set to High Quality. (The setting is found in the PropertyManager for the view in the Display Style panel. If it is already set to High Quality, then there will be no other view option; if it is not, then there will be an option that is set to Draft Quality.)
The image to the left in Figure 25.8 is the old setting with the draft quality view, and the image to the right is the new setting with the high quality view. 11. In the Component Line Font dialog box, set the Line Weight setting back to Default for the Bracket part, but keep it on the Bracket layer. 12. In the isometric view, Ctrl-click all of the tangent edges on the Bracket part, as shown in Figure 25.9. Click the Hide Edge toolbar button on the Line Format toolbar. 13. Click the Show Edge toolbar button. The PropertyManager message changes to indicate that you can now select hidden edges, and the hidden edges are shown. Ctrl-select the hidden edges and RMB click when you are done.
722
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 723
Using Layers, Line Fonts, and Colors
FIGURE 25.9 Hiding edges
Before
After
Summary While SolidWorks is not primarily built around the strength of its 2D drawing functionality, it offers more capabilities than most users take advantage of. Layers in SolidWorks offer adequate functionality, but could be improved by some automation to put parts on layers automatically; this would enable SolidWorks to show the parts in wireframe with the same colors assigned to the solid. Other line and edge display functionality is sometimes difficult to find or access, or may have obscure functions. Creating drawings that use color to make them easier to read should be easier in SolidWorks than it is in AutoCAD.
723
25
34_080139 ch25.qxp
3/26/07
5:30 PM
Page 724
35_080139 pt06.qxp
3/26/07
5:32 PM
Page 725
Using Advanced Techniques IN THIS PART Chapter 26 Modeling Multibodies Chapter 27 Working with Surfaces Chapter 28 Master Model Techniques
35_080139 pt06.qxp
3/26/07
5:32 PM
Page 726
36_080139 ch26.qxp
3/26/07
5:33 PM
Page 727
Modeling Multibodies
J
ust a few releases ago, SolidWorks software did not allow what were then called disjoint solids. Feature trees began with a base feature that could not be changed or reordered, and every part had to contain a single contiguous solid. Most SolidWorks users accepted this situation as good enough, mainly because most of the arguments for the need to use more than one solid within a single part were simply not convincing. However, as the usage of surfacing techniques in SolidWorks became more prevalent, it became apparent that surfaces and solids were not handled in the same ways. Users coming to SolidWorks from other high-end systems, such as Unigraphics, Pro/Engineer, Catia, and SDRC, already had some experience with the more complex techniques. Surfacing techniques resulted in surface geometry that was not contiguous. SolidWorks grouped the surface functions in with the reference geometry functions, such as planes and axes. With the advent of what became known as multibody modeling, a world of possibilities opened up. If you remove the constraint that all of the geometry in a part must be linked into a single solid body, and see the surface features also being created as independent bodies, then many more options become available. This created a best-practice crisis for some users. For years, the SolidWorks Corporation preached the doctrine that multiple bodies were not necessary, and indeed were somehow evil, and some users bought into that point of view. This was mainly preached by the sales side simply because SolidWorks lacked the functionality, and sales has a need to put a positive spin on technical issues.
727
IN THIS CHAPTER With great power comes great responsibility Understanding multibody techniques Creating multibodies Managing bodies
36_080139 ch26.qxp
Part VI
3/26/07
5:33 PM
Page 728
Using Advanced Techniques
Now that the functionality exists, how should conservative users look at this new functionality? What are the drawbacks and advantages, uses and limitations? When multibody modeling was first introduced in SolidWorks, adventurous users just used the new modeling tools because they could, and some actively went in search of the limits to see how far they could be taken, and in which directions. By the release of SolidWorks 2007, four or five releases have now offered multibody functionality, and have sorted through some of the first-generation issues that arose with multibody modeling. Some of the issues discussed here are general organizational issues with the broad concept of multiple bodies within a single part. Other issues are specific to SolidWorks, special quirks, tools, and tips.
With Great Power Comes Great Responsibility Multibody functionality provides the user with great power. Power can be wielded for the good or for the bad. I find myself using the same responsible-modeling speeches when discussing multibodies as I tend to use for in-context modeling. This is because multibodies present some of the same issues as in-context modeling. The first similarity is that on the surface, both techniques appear to be all-day-every-day types of design tools. The second similarity between them is that neither tool is what it appears to be on the surface. The responsibility part arises when thinking about other users who will use the multibody parts once they are created, even including yourself in that list. It is not always easy to remember how you executed a particular project six months and 100 models ago. Other users may have to edit your work, and if errors happen, then you have to be able to navigate the design intent without destroying the relationships in the FeatureManager or completely rebuilding it. This is the reason for trying to standardize best-practice issues, particularly in larger organizations where more users may work with the data. If you are an independent contractor and do not share your models with other SolidWorks users, then you have more flexibility to model how you like. As long as you can come back to the model and change it when you need to, more power to you.
Multibody modeling is not assembly modeling Multibody modeling is not assembly modeling. This concept is important, and so I will repeat it: Multibody modeling is not assembly modeling. Many times when new users are introduced to the capabilities of multib