PHASE BEHAVIOR CURTIS H. WHITSON AND MICHAEL R. BRULÉ
MONOGRAPH VOLUME 20
SPE
HENRY L. DOHERTY SERIES
PHASE BEHAVIOR Curtis H. Whitson Professor of Petroleum Engineering U. Trondheim, NTH and Founder PERA a/s and
Michael R. Brulé President and Chief Executive Officer Technomation Systems Inc.
First Printing Henry L. Doherty Memorial Fund of AIME Society of Petroleum Engineers Inc. Richardson, Texas 2000 i
SPE Monograph Series The Monograph Series of the Society of Petroleum Engineers was established in 1965 by action of the SPE Board of Directors. The Series is intended to provide authoritative, up-to-date treatment of the fundamental principles and state of the art in selected fields of technology. The Series is directed by the Society’s Monograph Committee. A committee member designated as Monograph Editor provides technical evaluation with the aid of the Review Committee. Below is a listing of those who have been most closely involved with the preparation of this monograph.
Monograph Review Committee Peter G. Christman, Shell Intl. E&P B.V., Monograph Editor David F. Bergman, Amoco Production Co. W. David Constant, Louisiana State U. A.S. Cullick, Landmark Graphics Corp. Gustave A. Mistrot III, Mistrot & Assocs. Teresa G. Monger-McClure, Marathon Oil Co. Franklin M. Orr Jr., Stanford U. Robert R. Wood, Shell Intl. E&P B.V. Aaron A. Zick, Zick Technologies
Monograph Committee (2000) Mary Jane Wilson, WZI, Chairperson Jesse Frederick, WZI Russell T. Johns, U. of Texas, Austin Medhat Kamal, Arco E&P Technology Mark Miller, U. of Texas, Austin Ken Newman, CTES L.S. Dan O’Meara Jr., U. of Oklahoma David Underdown, Chevron Production Technology Co.
Acknowledgments Many people contributed to the production of this monograph. It is first and foremost the product of the authors. I am sure that the effort was more significant than either author had anticipated, but they persevered and should be proud of the book they wrote. I want to thank R.R. Wood, who initiated the project, chose the authors, and formed a distinguished review committee. I succeeded Rob in 1990 and coordinated the efforts of A.A. Zick, G.A. Mistrot, T.G. Monger-McClure, D.F. Bergman, A.S. Cullick, and W.D. Constant, who reviewed every chapter from their own unique perspectives. F.M. Orr contributed significant reviews on selected chapters. It was a pleasure to work with such a talented group of engineers. I am confident that we kept the focus of the monograph on use by the working engineer. The book is meant to serve as a reference. As such, I hope it will be a valuable addition to the library of every petroleum engineer working in phase behavior. Peter G. Christman
Copyright 2000 by the Society of Petroleum Engineers Inc. Printed in the United States of America. All rights reserved. This book, or any part thereof, cannot be reproduced in any form without written consent of the publisher. ISBN 1-55563-087-1 ii
Dedication To Morris Muskat, a pioneer in the field of reservoir engineering, who made important contributions in the area of phase behavior.
iii
Acknowledgments We thank the SPE editorial staff, the Monograph Review Committee members, our professional colleagues, our students, and the petroleum industry at large for valuable assistance and input toward the completion of this monograph. In particular, we thank the two technical editors, Rob R. Wood and Peter G. Christman, and our staff editor, Flora Cohen. We have been strongly influenced by the pioneering phase-behavior research of Donald Katz, Muz Standing, and Ken Starling and the many others who have made invaluable contributions to the field. The scientific contributions of these engineers and their coworkers, together with contributions from the community of petroleum and chemical engineers, have laid the foundation for the material selected, synthesized, and presented in this monograph. We hope that all contributors have been correctly cited and given due credit for their contributions. We are confident that the material contained herein is valuable for dealing with engineering problems affected by phase behavior, both today and in the future. We use the technology presented in this monograph daily to solve problems for the industry and as the basis of our long-term research. Curtis H. Whitson Michael R. Brulé
iv
Table of Contents Chapter 1—Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 1.2 1.3 1.4 1.5
Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Historical Review . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Objectives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope and Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nomenclature and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 1 2 2 2
Chapter 2—Volumetric and Phase Behavior of Oil and Gas Systems . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 2.2 2.3 2.4 2.5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Reservoir-Fluid Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Phase Diagrams for Simple Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Retrograde Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Classification of Oilfield Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 3—Gas and Oil Properties and Correlations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.1 3.2 3.3 3.4 3.5 3.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Review of Properties, Nomenclature, and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gas Mixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil Mixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IFT and Diffusion Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . K-Value Correlations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 18 22 29 38 40
Chapter 4—Equation-of-State Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 4.1 4.2 4.3 4.4 4.5 4.6 4.7
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cubic EOS’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Two-Phase Flash Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Phase Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saturation-Pressure Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Equilibrium in a Gravity Field: Compositional Gradients . . . . . . . . . . . . . . . . . . . . Matching an EOS to Measured Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47 47 52 55 62 63 65
Chapter 5—Heptanes-Plus Characterization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 5.1 5.2 5.3 5.4 5.5 5.6 5.7
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Experimental Analyses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Molar Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inspection-Properties Estimation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Critical-Properties Estimation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Recommended C7) Characterizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Grouping and Averaging Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68 68 70 77 80 83 83
Chapter 6—Conventional PVT Measurements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 6.1 6.2 6.3 6.4 6.5 6.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wellstream Compositions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Multistage-Separator Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Constant Composition Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Differential Liberation Expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Constant Volume Depletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
88 88 91 93 95 97
Chapter 7—Black-Oil PVT Formulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 7.1 7.2 7.3 7.4 7.5 7.6
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traditional Black-Oil Formulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modified Black-Oil (MBO) Formulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications of MBO Formulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Partial-Density Formulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Modifications for Gas Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109 109 110 116 118 119
Chapter 8—Gas-Injection Processes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 8.1 8.2 8.3 8.4 8.5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miscibility and Related Phase Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lean-Gas Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enriched-Gas Miscible Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CO2 Injection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
121 122 128 131 135
Chapter 9—Water/Hydrocarbon Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 9.1 9.2 9.3 9.4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Properties and Correlations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EOS Predictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
142 142 150 151
Appendix A—Property Tables and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 Appendix B—Example Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172 Appendix C—Equation-of-State Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193 Appendix D—Understanding Laboratory Oil PVT Reports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 Author Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 Subject Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230
vi
Chapter 1
Introduction 1.1 Purpose This monograph covers a wide range of topics related to phase behavior. Phase behavior is the behavior of vapor, liquid, and solids as a function of pressure, temperature, and composition. In this monograph, “vapor” is used interchangeably with “gas,” “liquid” refers to oil and water, and “solids” include hydrates, asphaltenes, and wax. We are concerned primarily with the volumetric behavior and composition of phases, including density and isothermal compressibility, and component distribution in each phase. For a mixture with a known composition, we need to determine the vapor/liquid equilibrium (VLE), including saturation conditions over a wide range of temperatures and pressures. Transport properties are also needed for flow calculations (e.g., viscosity in Darcy’s law and molecular diffusion coefficients in Fick’s law). Phase behavior has many applications in petroleum engineering. The reservoir engineer relies on pressure/volume/temperature (PVT) relations to calculate oil and gas reserves, production forecasts, and the efficiency of enhanced oil recovery (EOR) methods. Most reservoir calculations require PVT properties at reservoir temperature. Production engineers use phase behavior data for surface separator design and to calculate flow in pipe, where such calculations are made over a range of temperatures from surface to reservoir conditions. Petroleum engineering calculations generally are made at temperatures from 60 to 350°F and at pressures from about 15 to 15,000 psia. 1.2 Historical Review Gibbs1,2 and van der Waals3 stated the basic theory of phase behavior in the the late 1800’s and early 1900’s. They formulated the concepts and mathematical relations necessary to describe phase behavior. Katz and Rzasa4 published a comprehensive review of phase behavior literature from before 1860 to 1945. Muckleroy5 published a bibliography covering 1946 to 1960, and other bibliographies exist for work in phase behavior over the past 30 years.* Experimental data on reservoir fluids were scarce before the late 1930’s, when Katz et al.4,6-39 at the U. of Michigan, Sage and colleagues40-73 at the California Inst. of Technology, and Eilerts et al.74-78 at the U.S. Bureau of Mines (USBM) began significant research programs. For 10 years, during the 1950’s, a large amount of high-quality experimental data was compiled on reservoir fluids. During the past 40 years, most phase behavior data have been measured by commercial service laboratories and major oil companies. *SPE Reprint Series No. 15 Phase Behavior gives a recent update of earlier bibliographies.
INTRODUCTION
These data have been used for engineering studies of primary depletion, waterflood evaluation, and gas-injection studies. Correlation of phase behavior data began in the 1940’s, with notable work by Standing and Katz,17,18 Bicher and Katz,25 Standing,79,80 Eilerts,78 Kennedy and colleagues,81-85 and others. Although equations of state (EOS’s) had been available for more than 50 years (since van der Waals3 published the first cubic EOS in 1873) it was necessary to rely mostly on tables, figures, and chart correlations, such as nomograms. These correlations provided reliable property estimates for engineering calculations through the 1970’s. Subsequently, empirical equations representing these graphical correlations were developed and programmed for calculators and computer applications. With the introduction of electronic computers in the late 1940’s, application of complicated thermodynamic models became possible. In 1949, Muskat and McDowell86 published one of the earliest papers in the SPE/AIME Transactions on applications of this new generation of computers. These authors solved the two-phase flash calculation with fixed K values for multistage separator design. Not until Redlich and Kwong87 introduced their classic cubic EOS in 1949 was it generally accepted that volumetric properties could be accurately predicted by use of theoretical models. Considerable advances were made in the 1950’s toward correlating volumetric properties of pure components with multiconstant EOS’s.88 By the early 1960’s, there was considerable activity in the application of sophisticated thermodynamic models to multicomponent VLE calculations, although most of this activity was in process engineering. In the 1960’s and 1970’s, Starling,89 Soave,90 and Peng and Robinson91 proposed several important modifications of existing EOS’s. Petroleum engineering EOS applications started seriously in the late 1970’s and early 1980’s, when EOS-based compositional reservoir simulators were introduced.92,93 At the same time, several methods were proposed for EOS fluid characterization of reservoir fluids, in particular for heptanes and heavier components.94-96 Finally, in the 1980’s, supercomputers appeared and special solution techniques were developed for compositional simulators,93 thereby making possible full-field, EOS compositional simulation. Today’s standard treatment of phase behavior in reservoir simulation is still based on formation volume factors (FVF’s) and surface gas/oil ratios (GOR’s). This will probably remain true for many years, in part because many problems can be solved adequately with a simple PVT formulation and in part because many petroleum engineers are not familiar with more complicated EOS models. This monograph treats both simple and complicated methods for estimating phase behavior. We suspect that the more complicated PVT 1
models will gradually become the standard, eventually replacing many of the simpler correlations.
with Chap. 6, Conventional PVT Experiments, and are included as a supplement to the discussion in that chapter.
1.3 Objectives This monograph provides the petroleum engineer with a tool to solve problems that require a description of phase behavior and specific PVT properties. These problems include calculating the FVF to determine original oil and gas in place and GOR’s, design of “optimal” surface separator conditions, and description of near-critical phase behavior resulting from the injection of a gas that develops miscibility with a reservoir oil. Because of the dramatic evolution in computer technology, petroleum engineers can now study such phenomena as developed miscibility,97 compositional gradients,98 and near-critical phase behavior99 with more sophisticated models. The quality of these models is sensitive to the EOS fluid characterizations. This monograph presents phase behavior concepts used in petroleum engineering and state-of-the-art technology for more complex phase behavior models, such as cubic EOS’s. We hope the monograph will serve its purpose for many years to come.
1.5 Nomenclature and Units SPE-approved symbols are used throughout the monograph. Some of these symbols will be unfamiliar even to the seasoned SPE reader (as they are confusing even to the authors!). One of the most significant changes in nomenclature that we have introduced is the use of different subscripts for surface and reservoir phases. Traditionally, o, g, and w are used for oil, gas, and water at reservoir and at surface conditions, a practice that was difficult to follow in Chaps. 6 and 7. We have therefore introduced the subscripts o, g, and w for surface phases, retaining o, g, and w for reservoir phases. A better solution to this problem was not apparent, particularly because some quantities required subscripts for both reservoir and surface phases—e.g., the gravity of surface gas produced from reservoir oil (written g go in this monograph). To avoid confusion in the property correlations in Chap. 3, gas and oil specific gravities are still written g g and g o (instead of g g and g o) because specific gravity is always reported at standard conditions. We use customary oilfield units (psi, ft3 and bbl, °F and °R, and lbm). The oilfield unit for mass is pound, written “lbm” to avoid confusion with pounds force, written “lbf.” Pounds force is never used explicitly in this monograph. Conversion factors to SI units are included at the end of each chapter, and Appendix A provides a comprehensive discussion of units and unit conversion tables. Standard conditions are defined in this monograph as 60°F and 14.7 psia. We recognize that standard pressure varies geographically and the calculation of surface gas volumes in some areas must use the locally defined value for standard pressure. To accomplish this, some constants given in the monograph must be recalculated.
1.4 Scope and Organization The scope of this monograph is limited mostly to two-phase, gas/oil phase behavior. Multiphase and vapor/solid phase behavior are discussed only briefly. Phase behavior related to chemical (surfactant and polymer) flooding is not covered because a detailed description would necessarily reduce coverage of problems more commonly encountered in petroleum engineering. We also think that this subject should be covered in a separate publication specifically within the context of chemical flooding technology. Chaps. 2 and 3 review the “nuts and bolts” of phase behavior principles, relevant PVT properties, and methods to solve most petroleum engineering problems. Useful correlations are presented for the most common PVT properties. Chap. 4 discusses cubic EOS’s, including the two-phase flash, saturation-pressure, and phase-stability calculations and numerical methods used to solve these VLE calculations. The problem of “tuning” an EOS to match measured PVT data is also addressed. Chap. 5 describes the characterization of heavy components (“heptanes plus”) in reservoir fluids for EOS applications. Experimental and mathematical methods describing the heptanes-plus material are presented, including splitting C7+ into petroleum fractions, estimating critical properties, and grouping an extended fluid characterization into a reduced number of pseudocomponents. Chap. 6 covers laboratory measurements of PVT properties and their application in engineering calculations. The standard PVT studies include constant composition (mass) expansion, differential liberation, constant-volume depletion, and the multistage separator test. Separator and bottomhole sampling methods for establishing wellstream composition are also discussed. Chap. 7 describes the black-oil PVT formulation and its extension to gas condensates, volatile oils, and gas-injection processes. The black-oil PVT formulation uses FVF’s and solution gas/oil ratios to relate phase and volumetric properties at reservoir conditions to surface volumes. Chap. 8 reviews the importance of phase behavior to gas-injection EOR processes. These processes include vaporizing, condensing, and the combined condensing/vaporizing miscible-drive mechanisms. CO2 immiscible and miscible drives and nitrogen injection are also reviewed. Chap. 9 covers the behavior of water/hydrocarbon phase and volumetric behavior, including mutual solubilities, water FVF and compressibility, and the treatment of hydrates. Appendix A gives tables of component properties, various other useful tables, and unit conversion factors. Appendix B includes more than 20 worked examples that range from simple calculations of ideal gas properties to detailed step-by-step EOS calculations for a ternary system. Appendix C gives two detailed EOS fluid characterizations, one for a gas condensate and another for a slightly volatile oil. Appendix D is a set of notes by M.B. Standing on understanding laboratory-oil PVT reports. These notes clearly belong 2
References 1. Gibbs, J.W.: The Collected Works of J. Willard Gibbs, Yale U. Press, New Haven, Connecticut (1948) 1. 2. Gibbs, J.W.: On the Equilibrium of Heterogeneous Substances, C. Works (ed.), Yale U. Press, New Haven, Connecticut (1928) Chap. 1. 3. van der Waals, J.D.: Continuity of the Gaseous and Liquid State of Matter (1873). 4. Katz, D.L. and Rzasa, M.J.: Biblography of Hydrocarbons Under Pressure 1860–1946, University Microfilms Inc. (1946). 5. Muckleroy, J.A.: Biblography on Hydrocarbons, 1946–1960, Gas Processors Assn. (1962). 6. Katz, D.L. and Hachmuth, K.K.: “Vaporization Equilibrium Constants in a Crude-Oil Natural Gas System,” Ind. & Eng. Chem. (1937) 29, 1072. 7. Katz, D.L.: “Application of Vaporization Equilibrium Constants to Production Engineering Problems,” Trans., AIME (1938) 127, 159. 8. Katz, D.L., Vink, D.J., and David, R.A.: “Phase Diagram of a Mixture of Natural Gas and Natural Gasoline Near the Critical Conditions,” Trans., AIME (1939) 136, 106. 9. Katz, D.L. and Singleterry, C.C.: “Significance of the Critical Phenomena in Oil and Gas Production,” Trans., AIME (1939) 132, 103. 10. Katz, D.L. and Saltman, W.: “Surface Tension of Hydrocarbons,” Ind. & Eng. Chem. (January 1939) 31, 91. 11. Katz, D.L. and Kurata, F.: “Retrograde Condensation,” Ind. & Eng. Chem. (June 1940) 32, No. 6, 817. 12. Wilcox, W.I., Carson, D.B., and Katz, D.L.: “Natural Gas Hydrates,” Ind. & Eng. Chem. (1941) 33, No. 5, 662. 13. Katz, D.L.: “High Pressure Gas Measurement,” Refiner and Natural Gasoline Manufacturer (June 1942). 14. Carson, D.B. and Katz, D.L.: “Natural Gas Hydrates,” Trans., AIME (1942) 146, 150. 15. Kurata, F. and Katz, D.L.: “Critical Properties of Volatile Hydrocarbon Mixtures,” Trans., AIChE (1942) 38, 995. 16. Katz, D.L.: “Possibilities of Secondary Recovery for the Oklahoma City Wilcox Sand,” Trans., AIME (1942) 146, 28. 17. Standing, M.B. and Katz, D.L.: “Density of Natural Gases,” Trans., AIME (1942) 146, 140. 18. Standing, M.B. and Katz, D.L.: “Density of Crude Oils Saturated with Natural Gas,” Trans., AIME (1942) 146, 159. 19. Katz, D.L.: “Prediction of the Shrinkage of Crude Oils,” Drill. & Prod. Prac. (1942) 137. 20. Matthews, T.A., Roland, C.H., and Katz, D.L.: “High Pressure Gas Measurement,” Proc., Natural Gas Assn. of America (NGAA) (1942) 41. PHASE BEHAVIOR MONOGRAPH
21. Weinaug, C.F. and Katz, D.L.: “Surface Tension of Methane-Propane Mixtures,” Ind. & Eng. Chem. (1943) 35, No. 2, 239. 22. Bicher, L.B. Jr. and Katz, D.L.: “Viscosities of the Methane-Propane System,” Ind. & Eng. Chem. (1943) 35, 754. 23. Katz, D.L., Monroe, R.R., and Trainer, R.P.: “Surface Tension of Crude Oils Containing Dissolved Gases,” Trans., AIME (1943) 155, 624. 24. Standing, M.B. and Katz, D.L.: “Vapor/Liquid Equilibria of Natural Gas/Crude Oil Systems,” Trans., AIME (1944) 155, 232. 25. Bicher, L.B. Jr. and Katz, D.L.: “Viscosity of Natural Gases,” Trans., AIME (1944) 155, 246. 26. Katz, D.L., Brown, G.G., and Parks, A.S.: “NGAA Report on Sampling Two-Phase Gas Streams from High Pressure Condensate Wells,” Proc., NGAA (September 1945). 27. Katz, D.L. and Beu, K.L.: “Nature of Asphaltic Substances,” Ind. & Eng. Chem. (February 1945) 37, 195. 28. Katz, D.L.: “Prediction of Conditions for Hydrate Formation in Natural Gases,” Trans., AIME (1945) 160, 140. 29. Poettman, F.H. and Katz, D.L.: “CO2 in a Natural Gas Condensate System,” Ind. & Eng. Chem. (1946) 38, 530. 30. Brown, G.G. et al..: Natural Gasoline and the Volatile Hydrocarbons, NGAA, Tulsa, Oklahoma (1948) 24–32. 31. Kobayashi, R. and Katz, D.L.: “Methane-n-Butane-Water System in Twoand Three-Phase Regions,” Ind. & Eng. Chem. (1948) 40, No. 5, 853. 32. Unruh, C.H. and Katz, D.L.: “Gas Hydrates of Carbon Dioxide/Methane Mixtures,” Trans., AIME (1949)186, 83. 33. Rzasa, M.J. and Katz, D.L.: “The Coexistence of Liquid and Vapor Phases at Pressures Above 10,000 psi,” Trans., AIME (1950) 189, 119. 34. Kobayashi, R. et al.: “Gas Hydrates Formation with Brine and Ethanol Solutions,” Proc., 30th Annual Convention of NGAA (1951). 35. Katz, D.L. and Williams, B.: “Reservoir Fluids and Their Behavior,” Amer. Soc. Petr. Geology Bulletin (February 1952) 36, No. 2, 342. 36. Katz, D.L.: “Possibility of Cycling Deep Depleted Oil Reservoirs After Compression to a Single Phase,” Trans., AIME (1952) 195, 175. 37. Kobayashi, R. and Katz, D.L.: “Vapor-Liquid Equilibria for Binary Hydrocarbon-Water Systems,” Ind. & Eng. Chem. (1953) 45, No. 2, 440. 38. Donnelly, H.C. and Katz, D.L.: “Phase Equilibria in the Carbon Dioxide-Methane System,” Ind. & Eng. Chem. (1954) 46, 511. 39. Katz, D.L. et al.: Handbook of Natural Gas Engineering, McGraw-Hill Book Co. Inc., New York City (1959). 40. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Volumetric Behavior of Hydrogen Sulfide,” Ind. & Eng. Chem. (1950) 42, 140. 41. Sage, B.H. and Olds, R.H.: “Volumetric Behavior of Oil and Gas from Several San Joaquin Valley Fields,” Trans., AIME (1947) 170, 156. 42. Olds, R.H., Sage, B.H., and Lacey, W.N.: “Partial Volumetric Behavior of the Methane-Carbon Dioxide System,” Fundamental Research on Occurrence and Recovery of Petroleum, API, Dallas (1943) 44. 43. Reamer, H.H. et al.: “Phase Equilibria in Hydrocarbon Systems—Volumetric Behavior of Ethane-Carbon Dioxide System,” Ind. & Eng. Chem. (1945) 37, 688. 44. Sage, B.H. and Lacey, W.N.: “Partial Volumetric Behavior of the Lighter Paraffin Hydrocarbons in the Gas Phase,” Drill. & Prod. Prac. (1939) 641. 45. Sage, B.H. and Lacey, W.N.: “Thermodynamic Properties of the Light Paraffin Hydrocarbons and Nitrogen,” API Research Project 37, monograph, API, New York City (1950). 46. Sage, B.H., Hicks, B.L., and Lacey, W.N.: “Partial Volumetric Behavior of the Lighter Hydrocarbons in the Liquid Phase,” Drill. & Prod. Prac. (1938) 402. 47. Sage, B.H. and Lacey, W.N.: “Apparatus for Determination of Volumetric Behavior of Fluids,” Trans., AIME (1948) 174, 102. 48. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Volumetric and Phase Behavior of the Methane-Propane Systems,” Ind. & Eng. Chem. (1950) 42, 534. 49. Sage, B.H., Lacey, W.N., and Schaafsma, J.G.: “Phase Equilibria in Hydrocarbon Systems: Methane-Propane Systems,” Ind. & Eng. Chem. (1934) 26, 214. 50. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Volumetric and Phase Behavior of the Methane-n Butane-Decane System,” Ind. & Eng. Chem. (1951) 43, 1436. 51. Sage, B.H. and Lacey, W.W.: Volumetric and Phase Behavior of Hydrocarbons, Gulf Publishing Co., Houston (1949). 52. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Phase Equilibria in Hydrocarbon Systems,” Ind. & Eng. Chem. (June 1951) 43, 1436. 53. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Phase Behavior in Hydrocarbon System,” Ind. & Eng. Chem. (1951) 43, 2515. 54. Olds, R.H. et al.: “Phase Equilibria in Hydrocarbon Systems. The Butane-Carbon Dioxide System,” Ind. & Eng. Chem. (1949) 41, 475. INTRODUCTION
55. Reamer, H.H. and Sage, B.H.: “Phase Equilibria in Hydrocarbon Systems—Volumetric and Phase Behavior of the n-Decane-CO2 System,” J. Chem. Eng. Data (1963) 8, 508. 56. Reamer, H.H., Fiskin, J.M., and Sage, B.H.: “Phase Equilibria in Hydrocarbon Systems: Phase Behavior in the Methane-n-Butane-Decane System at 160°F,” Ind. & Eng. Chem. (December 1949) 41, 2871. 57. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Phase Equilibria in Hydrocarbon Systems—Volumetric and Phase Behavior of the Methanen-Heptane System,” Ind. & Eng. Chem. (1956) 1, 29. 58. Sage, B.H., Webster, D.C., and Lacey, W.N.: “Phase Equilibria in Hydrocarbon Systems,” Ind. & Eng. Chem. (1936) 28, 1045. 59. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Phase Equilibria in Hydrocarbon Systems—Volumetric and Phase Behavior of the MethaneCyclohexane System,” Ind. & Eng. Chem. (1958) 3, 240. 60. Sage, B.H. and Lacey, W.N.: “Effect of Pressure Upon Viscosity of Methane and Two Natural Gases,” Trans., AIME (1938) 127, 118. 61. Sage, B.H., Yale, W.D., and Lacey, W.N.: “Effect of Pressure on Viscosity of n-Butane and i-Butane,” Ind. & Eng. Chem. (1939) 31, 223. 62. Sage, B.H. and Lacey, W.N.: “Gravitational Concentration Gradients in Static Columns of Hydrocarbon Fluids,” Trans., AIME (1939) 132, 120. 63. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Volumetric and Phase Behavior of the Methane-n-Butane-Decane System,” Ind. & Eng. Chem. (1947) 39, 77. 64. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Volumetric and Phase Behavior of the Methane-n-Butane-Decane System,” Ind. & Eng. Chem. (1952) 44, 1671. 65. Sage, B.H., Lacey, W.N., and Schaafsma, J.G.: “Behavior of Hydrocarbon Mixtures Illustrated by a Simple Case,” API Bulletin (1932) 212, 119. 66. Sage, B.H.: Thermodynamics of Multicomponent Systems, Reinhold Publishing Co. (1965) 67. Sage, B.H. and Lacey, W.N.: Volumetric and Pha.se Behavior of Hydrocarbons, Stanford Press, Stanford, Connecticut (1939). 68. Sage, B.H. and Reamer, R.H.: “Volumetric Behavior of Oil and Gas From the Rio Bravo Field,” Trans., AIME (1941) 142, 179. 69. Olds, R.H., Sage, B.H., and Lacey, W.N.: “Phase Equilibria in Hydrocarbon Systems. Composition of the Dew-Point Gas of the MethaneWater System,” Ind. & Eng. Chem. (1942) 34, No. 10, 1223. 70. Reamer, H.H. et al.: “Phase Equilibria in Hydrocarbon Systems. Composition of the Dew-Point Gas in the Ethane-Water System,” Ind. & Eng. Chem. (1943) 35, No. 7, 790. 71. Reamer, H.H. et al.: “Phase Equilibria in Hydrocarbon Systems. Compositions of the Coexisting Phases of n-Butane-Water System in the Three-Phase Region,” Ind. & Eng. Chem. (1944) 36, No. 4, 381. 72. Reamer, H.H., Sage, B.H., and Lacey, W.N.: “Phase Equilibria in Hydrocarbon Systems. n-Butane-Water System in the Two-Phase Region,” Ind. & Eng. Chem. (1952) 44, No. 3, 609. 73. Sage, B.H. and Lacey, W.N.: “Some Properties of the Lighter Hydrocarbons, Hydrogen Sulfide, and Carbon Dioxide,” API Research Project 37, monograph, API, New York City (1955). 74. Eilerts, C.K.: “The Reserve Fluid, Its Composition and Phase Behavior,” Oil & Gas J. (1 January 1947) 63. 75. Eilerts, C.K.: “Gas Condensate Reservoir Engineering, 1. The Reserve Fluid, Its Composition and Phase Behavior,” Oil & Gas J. (1 February 1947) 63. 76. Eilerts, C.K., Carlson, H.A., and Mullen, N.B.: “Effect of Added Nitrogen on Compressibility of Natural Gas,” World Oil (June 1948) 129. 77. Eilerts, C.K. et al.: “Phase Relations of a Gas-Condensate Fluid at Low Temperatures, Including the Critical State,” Pet. Eng. (February 1948) 19, 154. 78. Eilerts, C.K.: Phase Relations of Gas Condensate Fluids, Monograph 10, USBM, American Gas Assn., New York City (1957) I and II. 79. Standing, M.B.: “Vapor-Liquid Equilibria of Natural Gas-Crude Oil Systems,” PhD dissertation, U. of Michigan, Ann Arbor, MI (1941). 80. Standing, M.B.: “A Pressure-Volume-Temperature Correlation for Mixtures of California Oils and Gases,” Drill. & Prod. Prac. (1947) 275. 81. Alani, G.H. and Kennedy, H.T.: “Volumes of Liquid Hydrocarbons at High Temperatures and Pressures,” Trans., AIME (1960) 219, 288. 82. Kennedy, G.C.: “Pressure-Volume-Temperature Relations in CO2 at Elevated Temperatures and Pressures,” Amer. J. Sci. (April 1954) 252, 225. 83. Kennedy, H.T. and Bhagia, N.S.: “An EOS for Condensate Fluids,” JPT (September 1969) 379. 84. Little, J.E. and Kennedy, H.T.: “A Correlation of the Viscosity of Hydrocarbon Systems with Pressure, Temperature and Composition,” SPEJ (June 1968) 157; Trans., AIME, 243. 85. Nemeth, L.K. and Kennedy, H.T.: “A Correlation of Dewpoint Pressure With Fluid Composition and Temperature,” SPEJ (June 1967) 99; Trans., AIME (1967) 240. 3
86. Muskat, M. and McDowell, J.M.: “An Electrical Computer for Solving Phase Equilibrium Problems,” Trans., AIME (1949) 186, 291. 87. Redlich, O. and Kwong, J.N.S.: “On the Thermodynamics of Solutions, V: An Equation of State. Fugacities of Gaseous Solutions,” Chem. Rev. (1949) 44, 233. 88. Benedict, M., Webb, G.B., and Rubin, L.C.: “An Empirical Equation for Thermodynamic Properties of Light Hydrocarbons and Their Mixtures, I. Methane, Ethane, Propane, and n-Butane,” J. Chem. Phy. (1940) 8, 334. 89. Starling, K.E.: “A New Approach for Determining Equation-of-State Parameters Using Phase Equilibria Data,” SPEJ (December 1966) 363; Trans., AIME, 237. 90. Soave, G.: “Equilibrium Constants from a Modified Redlich-Kwong EOS,” Chem. Eng. Sci. (1972) 27, No. 6, 1197. 91. Peng, D.Y. and Robinson, D.B.: “A New-Constant EOS,” Ind. & Eng. Chem. Fund. (1976) 15, No. 1, 59. 92. Coats, K.H.: “An EOS Compositional Model,” SPEJ (October 1980) 363; Trans., AIME, 269. 93. Young, L.C. and Stephenson, R.E.: “A Generalized Compositional Approach for Reservoir Simulation,” SPEJ (October 1983) 727; Trans., AIME, 275. 94. Yarborough, L.: “Application of a Generalized Equation of State to Petroleum Reservoir Fluids,” Equations of State in Engineering and Re-
4
search, K.C. Chao and R.L. Robinson Jr. (eds.), Advances in Chemistry Series, American Chemical Soc. (1978) 182, 386–439. 95. Whitson, C.H.: “Characterizing Hydrocarbon Plus Fractions,” SPEJ (August 1983) 683; Trans., AIME, 275. 96. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “Characterization of Gas Condensate Mixtures,” C7 Fraction Characterization, L.G. Chorn and G.A. Mansoori (eds.), Advances in Thermodynamics, Taylor & Francis, New York City (1989) 1. 97. Zick, A.A.: “A Combined Condensing/Vaporizing Mechanism in the Displacement of Oil by Enriched Gases,” paper SPE 15493 presented at the 1986 SPE Annual Technical Conference and Exhibition, New Orleans, 5–8 October. 98. Schulte, A.M.: “Compositional Variations Within a Hydrocarbon Column Due to Gravity,” paper SPE 9235 presented at the 1980 SPE Annual Technical Conference and Exhibition, Dallas, 21–24 September. 99. Coats, K.H.: “Simulation of Gas Condensate Reservoir Performance,” JPT (October 1985) 1870.
SI Metric Conversion Factors °F (°F*32)/1.8 +°C psi 6.894 757 E)00 +kPa
PHASE BEHAVIOR MONOGRAPH
Chapter 2
Volumetric and Phase Behavior of Oil and Gas Systems 2.1 Introduction Petroleum reservoir fluids are naturally occurring mixtures of natural gas and crude oil that exist in the reservoir at elevated temperatures and pressures. Reservoir-fluid compositions typically include hundreds or thousands of hydrocarbons and a few nonhydrocarbons, such as nitrogen, CO2, and hydrogen sulfide. The physical properties of these mixtures depend primarily on composition and temperature and pressure conditions. Reservoir temperature can usually be assumed to be constant in a given reservoir or to be a weak function of depth. As oil and gas are produced, reservoir pressure decreases and the remaining hydrocarbon mixtures change in composition, volumetric properties, and phase behavior. Gas injection also may change reservoir-fluid composition and properties. Katz and Williams1 give an excellent review of reservoir fluids and their general behavior under different operating conditions. The hydrocarbon phases and connate water sharing the pore volume (PV) in a reservoir are in thermodynamic equilibrium. Strictly speaking, hydrocarbons and water should be treated simultaneously in phase-behavior calculations. At typical reservoir conditions, the effect of connate water on hydrocarbon phase behavior can usually be neglected. Water can, however, affect the total-system phase behavior (for example, when hydrates form from natural-gas/water mixtures). This chapter covers only two-phase, vapor/liquid phase behavior. Chap. 8 briefly covers three- and four-phase systems (vapor/liquid/ liquid and vapor/liquid/liquid/solids) for low-temperature CO2/oil and rich-gas/oil mixtures, and Chap. 9 gives the behavior of vapor and solids related to hydrates. Sec. 2.1 introduces the composition of petroleum reservoir fluids and emphasizes their chemical complexity. Because reservoir fluids are made up of many components, a detailed quantitative analysis is difficult to perform. Organic compounds found in reservoir fluids are expressed by a general formula that classifies even high-molecular-weight compounds containing sulfur, nitrogen, and oxygen. This chapter also gives a historical review of the American Petroleum Inst. (API) -supported projects that defined many of the compounds known today. Simple one- and two-component phase behavior can be helpful in describing the effects of pressure, temperature, and composition on the reservoir-fluid phase behavior. Sec. 2.2 presents pressure/temperature ( p-T), pressure/volume ( p-V), and pressure/composition ( p-x) phase diagrams of simple systems. The behavior of these idealized systems is qualitatively similar to the behavior of complex reservoir fluids, as Sec. 2.3 shows. VOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
Retrograde condensation is perhaps the most unusual phase behavior that petroleum reservoir fluids exhibit.* Sec. 2.4 discusses the definition of retrograde condensation and the effect of retrograde condensation on the behavior of gas-condensate reservoirs. Petroleum reservoir fluids can be divided into five general categories, in increasing order of chemical complexity: dry gas, wet gas, gas condensate, volatile oil, and black oil. However, the phase behaviors of gas condensates and volatile oils are considerably more complex than those of black oils. The component distribution in a reservoir fluid, not simply the number of components, determines how close a fluid is to a critical state. Complex phase behavior is typically associated with systems that are “near critical”: systems that usually contain 10 to 15 mol% of components that are heptanes and heavier (C7+). Since the early 1930’s, experimental data have been measured onfluids of each type listed above. Sec. 2.5 defines each fluid type by its p-T diagram. Also, general characteristics of reservoir fluids are summarized in terms of composition and surface properties, such as GOR and stock-tank-oil gravity. 2.2 ReservoirĆFluid Composition The nature and composition of a reservoir fluid depends somewhat on the depositional environment of the formation from which the fluid is produced. Geologic maturation also influences reservoir-fluid composition. Several theories offer explanations for the origin and formation of petroleum over geologic time; no single theory suffices to explain how oil and gas were formed in all reservoirs. One theory portrays reservoirs as giant high-temperature/high-pressure reactors with catalytic rock surfaces that slowly convert deposited organic matter into oil and gas. Other theories hypothesize that oil and gas were formed from bacterial action on deposited organic matter. Other investigators maintain that oil and gas may be formed in the same geologic formation but that each fluid migrates to “traps” at different elevations because of fluid-density differences and gravity forces. Crude oil and natural gas are composed of many chemical compounds with a wide range of molecular weights. Some estimates2-4 suggest that perhaps 3,000 organic compounds can exist in a single *Historically, retrograde condensation has been considered the most complex phase-behavior phenomenon observed by reservoir fluids. Perhaps equally intriguing are the phenomena of strong compositional gradients, the condensing/vaporizing miscible mechanism (Chap. 8), asphaltene precipitation, and low-temperature, multiphase CO2 behavior.
1
TABLE 2.1—COMPOSITION AND PROPERTIES OF SEVERAL RESERVOIR FLUIDS Composition (mol%) Gas
Near-Critical
Component
Dry Gas
Wet Gas
Condensate
Oil
Volatile Oil
Black Oil
CO2
0.10
1.41
2.37
1.30
0.93
0.02
N2
2.07
0.25
0.31
0.56
0.21
0.34
C1
86.12
92.46
73.19
69.44
58.77
34.62
C2
5.91
3.18
7.80
7.88
7.57
4.11
C3
3.58
1.01
3.55
4.26
4.09
1.01
i-C4
1.72
n-C4 i-C5
0.50
0.28
0.71
0.89
0.91
0.76
0.24
1.45
2.14
2.09
0.49
0.13
0.64
0.90
0.77
0.43
n-C5
0.08
0.68
1.13
1.15
0.21
C6(s)
0.14
1.09
1.46
1.75
1.61
C7 +
0.82
8.21
10.04
21.76
56.40
Properties MC g
7)
C 7)
K wC
7
130
184
219
228
274
0.763
0.816
0.839
0.858
0.920
12.00
11.95
11.98
11.83
11.47
1,490
300
38
24
GOR, scf/STB
∞
105,000
5,450
3,650
OGR, STB/MMscf
0
10
180
275
57
49
45
gAPI gg
0.61
0.70
0.71
0.70
0.63
psat, psia
3,430
6.560
7,015
5,420
2,810
0.0051
0.0039
2.78
1.73
1.16
9.61
26.7
30.7
38.2
51.4
Bsat, ft3/scf or bbl/STB ò sat, lbmńft
3
reservoir fluid. The lighter and simpler compounds are produced as natural gas after surface separation, whereas the heavier and more complex compounds form crude oil at stock-tank conditions. Table 2.1 gives typical oilfield molar compositions for reservoir mixtures. The heavier components are usually lumped into a “plus” fraction instead of being identified individually. Chap. 5 discusses methods of quantifying and characterizing the components that make up the plus fraction—usually heptanes-plus. Natural gas is composed mainly of low-molecular-weight alkanes (methane through butanes), CO2, hydrogen sulfide, nitrogen, and, in some cases, lesser quantities of helium, hydrogen, CO, and carbonyl sulfide.5 Most crude oils are composed mainly of hydrocarbons (hydrogen and carbon compounds). The broad spectrum of organic compounds found in petroleum during the formation of crude oil also includes sulfur, nitrogen, oxygen, and trace metals. Tars and asphalts are solid or semisolid mixtures that include bitumen, pitch, waxes, and resins. These high-molecular-weight complex colloidal suspensions exhibit non-Newtonian rheology. The temperature and pressure gradients in a formation may cause reservoir-fluid properties to vary as a function of depth. “Compositional grading” is the continual change of composition as a function of depth.6-8 In compositional grading, reservoir temperature may be near the critical temperature of reservoir fluid(s) at certain depths in the reservoir. Physically, the thermodynamic forces of individual components in a near-critical mixture are of the same order of magnitude as gravity forces that tend to separate the lighter from the heavier components. The result can be a transition from an undersaturated gas condensate at the highest elevation to an undersaturated oil at the lowest elevation, with or without a visible phase transition from gas to oil (gas/oil contact). In petroleum refining, crude oil is often categorized according to its base and the hydrocarbon series (paraffin, naphthene, or aromatic) it contains in the highest concentration. Figs. 2.1 and 2.29 illustrate the types and relative amounts of hydrocarbon series that can be found in typical petroleum-refinery products. Nelson3 gives a full account of basic hydrocarbon chemistry and test methods that 2
have been used for many years to determine petroleum composition and inspection properties for refining purposes. The more common test methods include paraffin, naphthene, and aromatic; saturates, aromatics, resins, and asphaltenes; and Strieter (asphaltenes, resins, and oils) analyses; oil gravity in °API; Reid vapor pressure; trueboiling-point distillation; flash, fire, cloud, and pour points; color; and Saybolt and Furol viscosities. Chap. 5 discusses some of these methods that are used in petroleum engineering. The empirical formula Cn H2n)h Sa Nb Oc can be used to classify nearly all compounds found in crude oil. The largest portion of crude oil is composed of hydrocarbons with carbon number, n, ranging from 1 to about 60, and h numbers ranging from h+)2 for lowmolecular-weight paraffin hydrocarbons to h+*20 for high-molecular-weight organic compounds (e.g., polycyclic aromatic hydrocarbons). Occasionally, sulfur, nitrogen, and oxygen substitutions occur in high-molecular-weight organic compounds, with a, b, and c usually ranging from 1 to 3.2,10 Over the past 60 years, petroleum chemists have identified hundreds of the complex organic compounds found in petroleum. Beginning in 1927, Rossini and others11,12 conducted a lengthy investigation of the composition of petroleum [API Research Project 6 (API 6)] to develop and improve petroleum-refining processes. It took API 6 investigators almost 40 years to elucidate the composition of a single midcontinent crude oil from Well No. 6 in South Ponca City, Oklahoma. Because compounds with carbon numbers u12 could not be isolated from crude oils, during 1940–66, API Research Project 42 focused on synthesizing and characterizing model hydrocarbons with high molecular weights. These model compounds were used for identifying compounds that could not be isolated from crude oil. A crude oil compound with analytical responses that matched those of a synthesized model compound was inferred to have a similar chemical structure. Other API projects13 followed API 6, and increasingly more complex petroleum compounds were identified. API 48 focused on sulfur compounds, API 52 on nitrogen compounds, and API 56 on orPHASE BEHAVIOR
Fig. 2.1—Petroleum products identified according to carbon number.
ganometallic compounds. API 60 extended the work of API 6 to include petroleum heavy ends. In 1975, API stopped sponsoring basic research into the composition of petroleum. From 1975 to 1982, the petroleum engineering industry made additional advances in analytical techniques mainly because of the synfuels effort. The most sophisticated analytical techniques now in use include highly selective solvent extraction14-16; simulated distillation; gel permeation, high-performance liquid,17 and supercritical chromatography18; and mass infrared, 13C nuclear magnetic resonance,19 and Fourier-transform infrared spectroscopy. The American Chemical Soc. Div. of Petroleum Chemistry provides a comprehensive review of this area of research every 2 to 3 years. Table 2.220 shows an example of a crude-oil distillate classified by h number (in the general formula Cn H2n)h Sa Nb Oc ) and probable structural type, which determines the range of possible n numbers. Within and across each hydrocarbon class, many isomers share h and n numbers. The alkane (paraffin) series (h+2) has completely saturated hydrocarbon chains that are chemically very stable. The alkene (olefin) and alkyne (acetylene) series (h+0 and h+*2) are composed of unsaturated, straight-chain hydrocarbons. Because alkenes and alkynes are reactive, they are not usually found in naturally occurring petroleum deposits. The naphthene series (h+0), saturated-ring or cyclic compounds, are found in nearly all crudes. The aromatic or “benzene” series (h+*6) are unsaturated cyclic compounds. Low-boiling-point aromatics, which are also reactive, are found in relatively low concentrations in crude oil. Heavier crude oils are characterized by unsaturated polycyclic aromatic hydrocarbons with increasingly negative h numVOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
bers. As molecular weight increases, these compounds assume varying degrees of fused-ring saturation, with occasional hydrocarbon side chains. Sulfur, nitrogen, and oxygen can be substituted in the fused hydrocarbon rings to form heterocyclics or can occupy various positions on side chains.21 Metals, such as nickel and vanadium, can form organometallic compounds (porphyrins) in crude oil.2,10 Asphalts, bitumens, and tars are complex colloidal mixtures of carboids, carbenes, asphaltenes, and maltenes (resins and oils). Micellar structures of carboids, carbenes, and asphaltenes are formed by aromatic polycondensation reactions and are maintained in colloidal suspension by the maltenes. These fractions are separated according to their solubility or lack of solubility in certain low-molecular-weight solvents, such as propane, pentane, n-hexane, and carbon disulfide. Fig. 2.316 shows a hypothetical chemical structure of an asphaltene. The bracket around the structure implies that the structure is repeated three times. Although asphalt mixtures are complex in composition and rheology, they follow certain molecular-weight distributions that can be characterized as discussed in Chap. 5. Understanding the nature of asphaltenes is important in petroleum engineering because, even in low concentrations, asphaltenes can markedly affect reservoir-fluid phase behavior.22 Because asphaltenes are polar and hydrogen bonding, they alter reservoir wettability by adsorbing onto the rock surface.23 This alteration of reservoir wettability may affect capillary pressure, relative-permeability relations, residual oil saturations, waterflood behavior, dispersion, and electrical properties. Figs. 2.2 and 2.3 vividly show that the composition of crude oil is considerably more complex than the Cn H2n)2 straight-chain models commonly thought of as “oil.” This complexity 3
Fig. 2.2—Summary of hydrocarbons to be expected in crude-oil fractions (from Neumann et al.9).
should be borne in mind when modeling the phase behavior of complex reservoir fluids, particularly in gas-injection projects.23,24 2.3 Phase Diagrams for Simple Systems The dependence of volumetric and phase behavior on temperature, pressure, and composition is similar for simple (two- and threecomponent) and complex (multicomponent) systems. Traditionally, the introduction to phase behavior of complex reservoir fluids starts with a description of the vapor-pressure and volumetric behavior of single components. The introduction then proceeds to the behavior of two- and three-component systems, and finally to the behavior of complex multicomponent systems. Part of the rationale for this procession lies in the Gibbs phase rule.25,26 The Gibbs phase rule states that the number of intensive variables (i.e., degrees of freedom), F, that must be specified to determine the thermodynamic state of equilibrium for a mixture containing n components distributed in P phases (gas, liquid, and/or solid), is F + n * P ) 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (2.1) Intensive (thermodynamic) variables, such as temperature, pressure, and density, do not depend on the amount of material in the system. Extensive variables, such as flow rate, total mass, or liquid volume, depend on the extent of the system. To attain equilibrium requires that no net interphase mass transfer can occur. Thus, the temperatures and pressures of the coexisting 4
phases must be the same and the chemical potentials of each component in each phase must be equal. A more stringent definition of phase equilibrium includes other forces in addition to chemical potential (e.g., gravity and capillarity). On the basis of Eq. 2.1, for a two-phase, single-component system, F+1 and only temperature or pressure needs to be specified to determine the thermodynamic state of the system. For a two-phase, twocomponent system, F+2 and both temperature and pressure need to be specified to define the thermodynamic state of the mixture. Twophase binary systems allow one to focus on the effect of temperature and pressure on the composition and the relative amounts of each of the two phases, regardless of the composition of the overall mixture. The Gibbs phase rule implies that as the number of components increases to n in a two-phase mixture, n*2 composition variables must be specified in addition to temperature and pressure. If more than two phases are present, then n*P variables must be specified in addition to temperature and pressure. Because reservoir fluids comprise many components, the number of variables that must be defined to determine the state of a reservoir fluid is conceptually unmanageable. Therefore, simple systems are often used to model the basic volumetric and phase behavior of crude oil mixtures. Note that the phase rule must be modified if other potential fields are considered. For example, if the force of gravity is considered, as PHASE BEHAVIOR
TABLE 2.2—DISTRIBUTION OF h SERIES FROM 698 TO 995°F DISTILLATE OF SWAN HILLS CRUDE OIL (Ref. 20) Mass h Series
Probable Type
*12
Naphthalenes
*14
Naphthenonaphthalenes and/or biphenyls
*16
Dinaphthenaphthalenes and/or
*18
Trinaphthenaphthalenes and/or
*20
Tetranaphthenaphthalenes and/or
*22
Pentanaphthenaphthalenes and/or
*24
Hexanaphthenaphthalenes and/or
naphthenobiphenyls dinaphthenobiphenyls trinaphthenobiphenyls tetranaphthenobiphenyls pentanaphthenobiphenyls *26
Heptanaphthenaphthalenes and/or
*28
Octanaphthenaphthalenes and/or
*4S
Tricyclic sulfides
*6S
Tetracyclic sulfides
*8S
Pentacyclic sulfides
*10S
Hexacyclic sulfides
hexanaphthenobiphenyls heptanaphthenobiphenyls
*8S
Thiaindanes/thiatetralins
*10S
Naphthenothiaindanes/thiatetralins
*12S
Dinaphthenothiaindanes/thiatetralins
*14S
Trinaphthenothiaindanes/thiatetralins
*10S
Benzothiophenes
*12S
Naphthenobenzothiophenes
is done when calculating compositional variation with depth, the phase rule is F+n*P)3.7 2.3.1 Single-Component Systems. The p-T curve shown in Fig. 2.4 is a portion of the vapor-pressure curve for a typical hydrocarbon compound. Above and to the left of the curve, the hydrocarbon behaves as a liquid; below and to the right, the hydrocarbon behaves as a vapor. Saturated liquid and vapor coexist at every point along the vapor-pressure curve. The curve ends at the critical temperature and critical pressure of the hydrocarbon (the “critical point”). Fig. 2.5 shows a 3D PVT diagram of a pure compound. The critical temperature of a single component defines the temperature above which any gas/liquid mixture cannot coexist, regardless of pressure. Similarly, the critical pressure defines the pressure above which liquid and vapor cannot coexist, regardless of temperature. Along the vapor-pressure curve, two phases coexist in equilibrium. At the critical point, the vapor and liquid phases can no longer be distinguished, and their intensive properties are identical. For a multicomponent system, the definition of the critical point is also based on a temperature and pressure at which the vapor and liquid phases are indistinguishable. However, for a single-component system, the two-phase region terminates at the critical point. In a multicomponent system, the two-phase region can extend beyond the system’s critical point (i.e., at temperatures greater than the critical temperature and pressures greater than the critical pressure). Fig. 2.627 illustrates the continuity of gas and liquid phases for pure components. In this figure, the darker shading corresponds to higher density. A sharp contrast in phase densities is readily apparent along the vapor-pressure curve. As temperature increases along the vaporpressure curve, the discontinuity becomes harder to discern, until finally, at the critical point, the contrast in shading is hardly noticeable. Qualitatively, the behavior described by the shading in Fig. 2.6 is the same for multicomponent mixtures in the undersaturated region. VOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
Fig. 2.3—Hypothetical structure of a petroleum asphaltene (after Speight and Moschopedis14).
pc
Fig. 2.4—p-T diagram for a single component in the region of vapor/liquid behavior near the critical point ( pc +critical pressure and Tc +critical temperature).
Phase changes do not have to take place abruptly if certain temperature and pressure paths are followed. A process can start as a saturated liquid and end as a saturated vapor, with no abrupt change in phase. The path D–A–E–F–G–B–D in Fig. 2.4 is an example of a process that changes phases without crossing the vapor-pressure curve. Pure components actually exist as a saturated “liquid” and “vapor” only along the vapor-pressure curve. At other pressures and temperatures, the component only behaves “liquid-like” or “vaporlike,” depending on the location of the system temperature and pressure relative to the system’s critical point. Katz28 suggested calling a pure substance “single-phase fluid” at pressures greater than the critical pressure. Strictly speaking, the terms liquid-like and vaporlike should be used to describe undersaturated fluids. 5
Fig. 2.5—Three-dimensional schematic of the PVT surface of a pure compound (source unknown).
ponent is a saturated liquid. Similarly, the saturation curve to the right of the critical point (Point B to Point C) defines the dewpoint curve, along which the component is a saturated vapor. For any temperature less than the critical temperature, successive decreases in volume will elevate the pressure of the vapor until the “dewpoint” (vapor pressure) is reached (Point B on Fig. 2.7). At these conditions, the component is a saturated vapor in equilibrium with an infinitesimal amount of saturated liquid. Further decreases in the volume at constant temperature will result in proportionate increases in the amount of saturated liquid condensed, but the pressure does not change (i.e., the system pressure remains equal to the vapor pressure). While more liquid is being formed, the total volume (at Point D) is being reduced. However, the densities and other intensive properties of the saturated vapor and saturated liquid remain constant as a consequence of the Gibbs phase rule. A simple mass balance further shows that the ratio of liquid to vapor equals the ratio of Curve B–D to Curve D–A. Further decreases in volume will condense more liquid until the bubblepoint is reached. At the bubblepoint, the system is 100% saturated liquid in equilibrium with an infinitesimal amount of saturated vapor. Further decreases in volume beyond the bubblepoint are accompanied by a large increase in pressure because the liquid is only slightly compressible. This is indicated by the nearly vertical isotherms on the left side of Fig. 2.7. In the undersaturated vapor region on the right side of the diagram, a large change in volume reduces pressure only slightly because the vapor is highly compressible.
Fig. 2.726 shows a p-V diagram for ethane. The area enclosed by the saturation envelope represents the two-phase region. The area to the left of the envelope is the liquid-like region, and the area to the right is the vapor-like region. Point C represents the critical point. The saturation curve to the left of the critical point (from Point A to Point C) defines the bubblepoint curve, along which the com-
2.3.2 Two-Component Systems. Two-component systems are slightly more complex than single-component systems because both temperature and pressure affect phase behavior in the saturated region. Two important differences between single- and two-component systems exist. The saturated p-T projection is represented by a phase envelope rather than by a vapor-pressure curve, and the criti-
3,000
2,000
1,000
0
0
100
200
300
400
500
600
Temperature, °F Fig. 2.6—Continuity of vapor and liquid states for a single component along the vapor-pressure curve and at supercritical conditions (after Katz and Kurata27). 6
PHASE BEHAVIOR
Specific volume, ft3/lbm Fig. 2.7—p-V diagram for ethane at three temperatures (from Standing26).
cal temperature and critical pressure no longer define the extent of the two-phase, vapor/liquid region. Fig. 2.829 compares the p-T and p-V behavior of pure compounds and mixtures. Fig. 2.926 is a p-T projection of the ethane/n-heptane system for a fixed composition. For a single-component system, the dew- and bubblepoint curves are one in the same; i.e., they coincide with the vapor-pressure curve. In a binary (or other multicomponent) system, the dew- and bubblepoint curves no longer coincide, and a phase envelope results instead of a vapor-pressure curve. To the left of the phase envelope, the mixture behaves liquid-like, and to the right it behaves vapor-like. For binary or other multicomponent systems, the critical temperature and pressure are defined as the point where the dew- and bubblepoint curves intersect. At this point, the equilibrium phases are physically indistinguishable. Also, in contrast to the single-component system, two phases can exist at temperatures and pressures greater than the critical temperature and pressure. The highest temperature at which two phases can coexist in equilibrium is defined as the cricondentherm (Tangent b–b in Fig. 2.9). Similarly, the highest pressure at which two phases can coexist is defined as the cricondenbar (Tangent a–a). In the single-phase region, vapor and liquid are distinguished only by their densities and other physical properties. The region just beyond the critical point of a mixture has often been called the “supercritical” or “dense-fluid” region. Here, the fluid is considered to be neither gas nor liquid because the fluid properties are not strictly liquid-like or vapor-like. Kay30 measured the phase behavior of the binary ethane/n-heptane system for several compositions, as Fig. 2.10 shows. On the left side of this figure, the curve terminating at Point C is the vapor pressure of pure ethane; the curve on the right, terminating at Point C7, is the vapor pressure of pure n-heptane. Points C1 through C3 are the critical points of ethane/n-heptane mixtures at different compositions. The dashed line represents the locus of critical points for the infinite number of possible ethane/n-heptane mixtures. Each mixture composition has its own p-T phase envelope. The three compositions shown, which are 90.22, 50.25, and 9.78 wt% ethane, represent a system that is mainly ethane, a system that is one-half ethane and one-half n-heptane (by weight), and a system that is mainly n-heptane, respectively. Several interesting features of binary and multicomponent systems can be studied from these three mixtures. As composition changes, the location of the critical point and the shape of the p-T phase diagram also change. Note that the critical pressures of many (but not all) mixtures are higher than the critical pressures of the components composing the VOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
mixture. With a mixture composed mainly of ethane, the critical point lies to the left of the cricondentherm. Such a system is analogous to a reservoir gas-condensate system. As the percentage of ethane in the mixture increases further, the critical point of the system approaches that of pure ethane. The critical point for the mixture composed mostly of n-heptane lies below the cricondenbar. This system is analogous to a reservoir black-oil system. As the percentage of n-heptane increases, the critical point of the mixture approaches that of pure n-heptane. With equal percentages of ethane and n-heptane, the critical pressure is close to the cricondenbar of ethane and n-heptane. As the concentration of each component becomes similar, the two-phase region becomes larger. Other binaries provide additional insight into the effect of widely differing boiling points of the components making up the system. Fig. 2.1131 shows the vapor pressure of several hydrocarbons and the critical loci of their binary mixtures with methane. As the boiling points of the methane/hydrocarbon binary become more dissimilar, the two-phase region becomes larger and the critical pressure increases. For binaries with components that have similar molecular structures, the loci of critical points are relatively flat. 2.3.3 Multicomponent Systems. Phase diagrams for naturally occurring reservoir fluids are similar to those for binary mixtures. Fig. 2.125 is the first p-T phase diagram measured for a complex gascondensate system. This p-T diagram is particularly useful because it exhibits oil-like to gas-like behavior over a range of typical reservoir temperatures, from 80 to 240°F. Katz and coworkers32 used a glass-windowed cell to measure the distribution of gas and liquid phases throughout the two-phase region and near the mixture’s critical point. Fig. 2.135 shows isotherms of volume percent vs. pressure that were measured to determine the two-phase boundary and the volume-percent quality lines in the p-T diagram in Fig. 2.12. 2.4 Retrograde Condensation Kurata and Katz33 give the most concise and relevant discussion of retrograde phenomena related to petroleum engineering. In 1892, Kuenen34 used the term “retrograde condensation” to describe the anomalous behavior of a mixture that forms a liquid by an isothermal decrease in pressure or by an isobaric increase in temperature. Conversely, “retrograde vaporization” can be used to describe the formation of vapor by an isothermal increase in pressure or by an isobaric decrease in temperature. Neither form of retrograde behavior occurs in single-component systems. Fig. 2.14 is a constant-composition p-T projection of a multicomponent system. The diagram shows lines of constant liquid volume percent (quality). Although total composition is fixed, the respective compositions of saturated vapor and liquid phases change along the quality lines. The bubblepoint curve represents the locus of 100% liquid, and the dewpoint curve represents the locus of 0% liquid. The bubble- and dewpoint curves meet at the mixture critical point. Lines of constant quality also converge at the mixture critical point. The regions of retrograde behavior are defined by the lines of constant quality that exhibit a maximum with respect to temperature or pressure. Fig. 2.14 shows that for retrograde phenomena to occur, the temperature must be between the critical temperature and the cricondentherm. Fig. 2.1535 illustrates the liquid volumetric behavior of a lean gas-condensate system measured by Eilerts et al.35-37 Fig. 2.12 shows the p-T diagram of a reservoir mixture that would be considered a gas condensate if it had been discovered at a reservoir temperature of, for example, 200°F and an initial pressure of 2,700 psia. For these initial conditions, if reservoir pressure drops below 2,560 psia from depletion, the dewpoint will be passed and a liquid phase will develop in the reservoir. Liquid dropout will continue to increase until the pressure reaches 2,300 psia, when a maximum of 25 vol% liquid will have accumulated. According to Fig. 2.12, further pressure reduction will revaporize most of the condensed liquid. These comments assume that the overall composition of the reservoir mixture remains constant during depletion, a reasonable assumption in the context of this general discussion. In reality, howev7
Fig. 2.8—Qualitative p-T and p-V plots for pure fluids and mixtures; Vc +critical volume (after Edmister and Lee29).
er, the behavior of liquid dropout and revaporization differs from that suggested by constant-composition analysis. The retrograde liquid saturation is usually less than the saturation needed to mobilize the liquid phase. Because the heavier components in the original mixture constitute most of the (immobile) condensate saturation, the overall molecular weight of the remaining reservoir fluid increases during depletion. The phase envelope for this heavier reservoir mixture is pushed down and to the right of the original phase diagram (Fig. 2.16); the critical point is shifted to the right toward a higher temperature. It is not unusual that a retrograde-condensate mixture under depletion will reach a condition where the overall composition would exhibit a bubblepoint pressure if the reservoir were repressured (i.e., the overall mixture critical temperature becomes greater than the reservoir temperature). This change in overall reservoir composition results in less revaporization at lower pressures. Fig. 2.17 shows the difference between constant-composition and “depletion” liquid-dropout curves. 8
2.5 Classification of Oilfield Systems One might assume that the name used to identify a reservoir fluid should not influence how the fluid is treated as long as its physical properties are correctly defined. In theory this is true, but in practice we are usually required to define petroleum reservoir fluids as either “oil” or “gas.” For example, regulatory bodies require the definition of reservoir fluid for well spacing and determining allowable production rates and field-development strategy (e.g., unitization). The classification of a reservoir fluid as dry gas, wet gas, gas condensate, volatile oil, or black oil is determined (1) by the location of the reservoir temperature with respect to the critical temperature and the cricondentherm and (2) by the location of the first-stage separator temperature and pressure with respect to the phase diagram of the reservoir fluid. Fig. 2.18 illustrates how four types of depletion reservoirs for the same hydrocarbon system are defined by the location of the initial reservoir temperature and pressure. PHASE BEHAVIOR
Fig. 2.10—p-T diagram for the C2/n-C7 system at various concentrations of C2 (after Kay30).
Fig. 2.9—p-T diagram for a C2/n-C7 mixture with 96.83 mol% ethane (from Standing26).
Fig. 2.11—p-T diagram for various hydrocarbon binaries illustrating the effects of molecular-weight differences on criticalpoint loci (after Brown et al.31). VOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
A reservoir fluid is classified as dry gas when the reservoir temperature is greater than the cricondentherm and surface/transport conditions are outside the two-phase envelope; as wet gas when the reservoir temperature is greater than the cricondentherm but the surface conditions are in the two-phase region; as gas condensate when the reservoir temperature is less than the cricondentherm and greater than the critical temperature; and as an oil (volatile or black oil) when the reservoir temperature is less than the mixture critical temperature. For a given reservoir temperature and pressure, Fig. 2.1938 shows the spectrum of reservoir fluids from wet gas to black oil expressed in terms of surface GOR’s and oil/gas ratios (OGR’s). A more quantitative classification is also given in Fig. 2.19 in terms of molar composition, by use of a ternary diagram. In the near-critical region, gas condensates have a C7+ concentration less than [12.5 mol% and volatile oils fall between 12.5 to 17.5 mol% C7+. Retrograde gas-condensate reservoirs26,39 typically exhibit GOR’s between 3,000 and 150,000 scf/STB (OGR’s from about 350 to 5 STB/MMscf) and liquid gravities between 40 and 60°API. The color of stock-tank liquid is expected to lighten from volatile-oil to gas-condensate systems, although light volatile oils may be yellowish or water-white and some condensate liquids can be dark brown
Fig. 2.12—p-T diagram for a gas-condensate system (after Katz et al.5). 9
Fig. 2.14—Hypothetical p-T diagram for a gas condensate showing the isothermal retrograde region.
Fig. 2.13—Volume isotherms for the gas-condensate p-T diagram in Fig. 2.12 (after Katz et al.5)
or even black. Color has not been a reliable means of differentiating clearly between gas condensates and volatile oils, but in general, dark colors indicate the presence of heavy hydrocarbons. In some cases, for condensate recovery from a surface process facility, the reservoir fluid is mistakenly interpreted to be a gas condensate. Strictly speaking, the definition of a gas condensate depends only on reservoir temperature. The definition of a reservoir fluid as wet or dry gas depends on conditions at the surface. This makes differentiation between dry and wet gas difficult because any gas can conceivably be cooled enough to condense a liquid phase. The classification of a fluid as an oil is unambiguous because the only requirement is that the reservoir temperature be less than the
BUBBLEPOINT
Fig. 2.15—Liquid volume (expressed as a liquid/gas ratio) behavior for a lean-gas-condensate system (from Eilerts et al.35). 10
PHASE BEHAVIOR
Fig. 2.16—Change in phase envelope during the depletion of a gas condensate.
critical temperature. However, the distinction between a black oil and a volatile oil is more arbitrary. Generally speaking, a volatile oil is a mixture with a relatively high solution gas/oil ratio. Volatile oils exhibit large changes in properties when pressure is reduced only somewhat below the bubblepoint. In an extreme case, the oil volume may shrink from 100 to 50% with a reduction in pressure of only 100 psi below the bubblepoint. Black-oil properties, on the other hand, exhibit gradual changes, with nearly linear pressure dependence below the bubblepoint. Volatile oils typically yield stock-tank-oil gravities greater than 35°API, surface GOR’s between 1,000 and 3,000 scf/STB, and FVF’s (see Formation Volume Factors in Chap. 6) greater than [1.5 RB/STB. Solution gas released from a volatile oil contains significant quantities of stock-tank liquid (condensate) when this gas is produced to the surface. Solution gas from black oils is usually considered “dry,” yielding insignificant stock-tank liquids when produced to surface conditions.
For engineering calculations, the liquid content of released solution gas is perhaps the most important distinction between volatile oils and black oils. This difference is also the basis for the modification of standard black-oil PVT properties discussed in Chap. 7. A reasonable engineering distinction between black oils and volatile oils can be made on the basis of simple reservoir material-balance calculations. If the total surface oil and gas recoveries calculated by a reservoir material balance with the standard black-oil PVT formulation are sufficiently close to the recoveries calculated by a compositional material balance, the oil can probably be considered a black oil (see Chap. 7). If calculated oil recoveries are significantly different, the reservoir mixture should be treated as a volatile oil by use of a compositional approach or the modified black-oil PVT properties outlined in Chap. 7. Several researchers40,41 have shown that a compositional material balance for depletion of volatile-oil reservoirs may predict from two to four times the surface liquid reBubblepoint or dissolved gas reservoirs
Dewpoint or gas condensate reservoirs
SingleĆphase gas reservoirs
CVD lower because of loss of C7+ in early depletion stages
CCE has stronger revaporization at low pressures because of greater (initial) mass of gas remaining in cell
Fig. 2.17—Retrograde volumes for constant-composition and constant-volume depletion experiments. VOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
Fig. 2.18—p-T diagram of a reservoir fluid illustrating different types of depletion reservoirs. 11
ple, the gas is probably saturated at initial reservoir conditions, and an equilibrium oil could exist at some lower elevation. Discovery of a saturated reservoir fluid will usually require further field delineation to substantiate the presence of a second equilibrium phase above or below the tested interval. This may entail running a repeat-formation-tester tool to determine the fluid-pressure gradient as a function of depth, or a new well may be required updip or downdip to the discovery well. Representative samples of saturated fluids may be difficult to obtain during a production test.42 Standing26 discusses the situation of an undersaturated gas condensate sampled during a test where bottomhole flowing pressure drops below the dewpoint pressure. The produced fluid, which is not representative of the original reservoir fluid, may have a dewpoint equal to initial reservoir pressure. This situation would incorrectly imply that the reservoir is saturated at initial conditions and that an underlying oil rim may exist. References
OGR (STB/MMscf) GOR (scf/STB)
Fig. 2.19—Spectrum of reservoir fluids in order of increasing chemical complexity from wet gas to black oil (from Cronquist38).
covery predicted by conventional material balances that are based on the standard black-oil PVT formulation. Fluid samples obtained from a new field discovery may be instrumental in defining the existence of an overlying gas cap or an underlying oil rim. Referring to Fig. 2.20, if the initial reservoir pressure equals the measured bubblepoint pressure of a bottomhole or recombined sample, the oil is probably saturated at initial reservoir conditions. This implies that an equilibrium gas cap could exist at some higher elevation. Likewise, if the initial reservoir pressure is the same as the measured dewpoint pressure of a reservoir gas sam-
}
Retrograde dewpoint = Resevoir pressure Bubblepoint
Fig. 2.20—p-T phase diagram of a gas-cap fluid in equilibrium with an underlying saturated oil. 12
1. Katz, D.L. and Williams, B.: “Reservoir Fluids and Their Behavior,” Amer. Soc. Pet. Geologists Bulletin (February 1952) 36, No. 2, 342. 2. Smith, H.M. et al.: “Keys to the Mystery of Crude Oil,” Trans., API, Dallas (1959) 433. 3. Nelson, W.L.: Petroleum Refinery Engineering, fourth edition, McGraw-Hill Book Co. Inc., New York City (1958). 4. Nelson, W.L.: “Does Crude Boil at 1400°F?,” Oil & Gas J. (1968) 125. 5. Katz, D.L. et al.: Handbook of Natural Gas Engineering, McGraw-Hill Book Co. Inc., New York City (1959). 6. Muskat, M.: “Distribution of Non-Reacting Fluids in the Gravitational Field,” Physical Review (1930) 35, 1384. 7. Sage, B.H. and Lacey, W.N.: “Gravitational Concentration Gradients in Static Columns of Hydrocarbon Fluids,” Trans., AIME (1939) 132, 120. 8. Schulte, A.M.: “Compositional Variations Within a Hydrocarbon Column Due to Gravity,” paper SPE 9235 presented at the 1980 SPE Annual Technical Conference and Exhibition, Dallas, 21–24 September. 9. Neumann, H.J., Paczynska-Lahme, B., and Severin, D.: Composition and Properties of Petroleum, Halsted Press, New York City (1981). 10. Thompson, C.J., Ward, C.C., and Ball, J.S.: “Characteristics of World’s Crude Oils and Results of API Research Project 60,” Report B-7, Energy R&D Admin. (ERDA) (1976). 11. Rossini, F.D.: “The Chemical Constitution of the Gasoline Fraction of Petroleum—API Research Project 6,” API, Dallas (1935). 12. Rossini, F.D. and Mair, B.J.: “The Work of the API Research Project on the Composition of Petroleum,” Proc., Fifth World Pet. Cong. (1954) 223. 13. Miller, A.E.: “Review of American Petroleum Institute Research Projects on Composition and Properties of Petroleum,” Proc., Fourth World Pet. Cong. (1955) 27. 14. Speight, J.C. and Moschopedis, S.E.: “On the Molecular Nature of Petroleum Asphaltenes,” Trans., Advances in Chemistry, American Chemical Soc. (1981) 195, 1. 15. Speight, J.G., Long, R.B., and Trowbridge, T.D.: “Factors Influencing the Separation of Asphaltenes from Heavy Petroleum Feedstocks,” Fuel (1984) 63, 616. 16. Speight, J.G. and Pancirov, R.J.: “Structural Types in Petroleum Asphaltenes as Deduced from Pyrolysis/Gas Chromatography/Mass Spectrometry,” Liquid Fuels Technology (1984) 2, No. 3, 287. 17. Such, C., Brulé, B., and Baluja-Santos, C.: “Characterization of a Road Asphalt by Chromatographic Techniques (GPC and HPLC),” J. Liquid Chrom. (1979) 2, No. 3, 437. 18. Fetzer, J.C. et al.: “Characterization of Carbonaceous Materials Using Extraction with Supercritical Pentane,” report, Contract No. DOE/ ER/00854-29, U.S. DOE (1980). 19. Helm, R.V. and Petersen, J.C.: “Compositional Studies of an Asphalt and Its Molecular Distillation Fractions by Nuclear Magnetic Resonance and Infrared Spectrometry,” Analytical Chemistry (1968) 40, No. 7, 1100. 20. Dooley, J.E. et al.: “Analyzing Heavy Ends of Crude, Swan Hills,” Hydro. Proc. (April 1974) 53, 93. 21. Dooley, J.E. et al.: “Analyzing Heavy Ends of Crude, Comparisons,” Hydro. Proc. (Nov. 1974) 53, 187. 22. Katz, D.L. and Beu, K.L.: “Nature of Asphaltic Substances,” Ind. & Eng. Chem. (February 1945) 37, 195. 23. Monger, T.G. and Trujillo, D.E.: “Organic Deposition During CO2 and Rich-Gas Flooding,” SPERE (February 1991) 17. 24. Bossler, R.B. and Crawford, P.B.: “Miscible-Phase Floods May Precipitate Asphalt,” Oil & Gas J. (23 February 1959) 57, 137. PHASE BEHAVIOR
25. Gibbs, J.W.: The Collected Works of J. Willard Gibbs, Yale U. Press, New Haven, Connecticut (1948). 26. Standing, M.B.: Volumetric and Phase Behavior of Oil Field Hydrocarbon Systems, SPE, Richardson, Texas (1977). 27. Katz, D.L. and Kurata, F.: “Retrograde Condensation,” Ind. & Eng. Chem. (June 1940) 32, No. 6, 817. 28. Katz, D.L. and Singleterry, C.C.: “Significance of the Critical Phenomena in Oil and Gas Production,” Trans., AIME (1939) 132, 103. 29. Edmister, W.C. and Lee, B.I.: Applied Hydrocarbon Thermodynamics, second edition, Gulf Publishing Co., Houston (1984) I. 30. Kay, W.B.: “The Ethane-Heptane System,” Ind. & Eng. Chem. (1938) 30, 459. 31. Brown, G.G. et al.: Natural Gasoline and the Volatile Hydrocarbons, NGAA, Tulsa, Oklahoma (1948) 24–32. 32. Katz, D.L., Vink, D.J., and David, R.A.: “Phase Diagram of a Mixture of Natural Gas and Natural Gasoline Near the Critical Conditions,” Trans., AIME (1939) 136, 165. 33. Kurata, F. and Katz, D.L.: “Critical Properties of Volatile Hydrocarbon Mixtures,” Trans., AIChE (1942) 38, 995. 34. Kuenen, J.P.: “On Retrograde Condensation and the Critical Phenomena of Two Substances,” Commun. Phys. Lab. U. Leiden (1892) 4, 7. 35. Eilerts, C.K.: Phase Relations of Gas Condensate Fluids, Monograph 10, USBM, American Gas Assn., New York City (1957) I and II. 36. Eilerts, C.K.: “Gas Condensate Reservoir Engineering, 1. The Reserve Fluid, Its Composition and Phase Behavior,” Oil & Gas J. (1 February 1947) 63.
VOLUMETRIC AND PHASE BEHAVIOR OF OIL AND GAS SYSTEMS
37. Eilerts, C.K. et al.: “Phase Relations of a Gas-Condensate Fluid at Low Tempertures, Including the Critical State,” Pet. Eng. (February 1948) 19, 154. 38. Cronquist, C.: “Dimensionless PVT Behavior of Gulf Coast Reservoir Oils,” JPT (May 1973) 538. 39. Moses, P.L.: “Engineering Applications of Phase Behavior of Crude Oil and Condensate Systems,” JPT (July 1986) 715. 40. Lohrenz, J., Clark, G.C., and Francis, R.J.: “A Compositional Material Balance for Combination Drive Reservoirs with Gas and Water Injection,” JPT (November 1963) 1233; Trans., AIME, 228. 41. Reudelhuber, F.O. and Hinds, R.F.: “Compositional Material-Balance Method for Prediction of Recovery From Volatile Oil Depletion Drive Reservoirs,” JPT (1957) 19; Trans., AIME, 210. 42. Fevang, Ø. and Whitson, C.H.: “Accurate In-Situ Compositions in Petroleum Reservoirs,” paper SPE 28829 presented at the 1994 European Petroleum Conference, London, 25–27 October.
SI Metric Conversion Factors °API 141.5/(131.5)°API) +g/cm3 bbl 1.589 873 E*01 +m3 ft3 2.831 685 E*02 +m3 °F (°F*32)/1.8 +°C gal 3.785 412 E*03 +m3 lbm 4.535 924 E*01 +kg psi 6.894 757 E)00 +kPa
13
Chapter 3
Gas and Oil Properties and Correlations 3.1 Introduction Chap. 3 covers the properties of oil and gas systems, their nomenclature and units, and correlations used for their prediction. Sec. 3.2 covers the fundamental engineering quantities used to describe phase behavior, including molecular quantities, critical and reduced properties, component fractions, mixing rules, volumetric properties, transport properties, and interfacial tension (IFT). Sec. 3.3 discusses the properties of gas mixtures, including correlations for Z factor, pseudocritical properties and wellstream gravity, gas viscosity, dewpoint pressure, and total formation volume factor (FVF). Sec. 3.4 covers oil properties, including correlations for bubblepoint pressure, compressibility, FVF, density, and viscosity. Sec. 3.5 gives correlations for IFT and diffusion coefficients. Sec. 3.6 reviews the estimation of K values for low-pressure applications, such as surface separator design, and convergence-pressure methods used for reservoir calculations. 3.2 Review of Properties, Nomenclature, and Units 3.2.1 Molecular Quantities. All matter is composed of elements that cannot be decomposed by ordinary chemical reactions. Carbon (C), hydrogen (H), sulfur (S), nitrogen (N), and oxygen (O) are examples of the elements found in naturally occurring petroleum systems. The physical unit of the element is the atom. Two or more elements may combine to form a chemical compound. Carbon dioxide (CO2), methane (CH4), and hydrogen sulfide (H2S) are examples of compounds found in naturally occurring petroleum systems. When two atoms of the same element combine, they form diatomic compounds, such as nitrogen (N2) and oxygen (O2). The physical unit of the compound is the molecule. Mass is the basic quantity for measuring the amount of a substance. Because chemical compounds always combine in a definite proportion (i.e., as a simple ratio of whole numbers), the mass of the atoms of different elements can be conveniently compared by relating them with a standard. The current standard is carbon-12, where the element carbon has been assigned a relative atomic mass of 12.011. The relative atomic mass of all other elements have been determined relative to the carbon-12 standard. The smallest element is hydrogen, which has a relative atomic mass of 1.0079. The relative atomic mass of one element contains the same number of atoms as the relative atomic mass of any other element. This is true regardless of the units used to measure mass. According to the SI standard, the definition of the mole reads “the mole is the amount of substance of a system which contains as many elementary entities as there are atoms in 0.012 kilograms of car18
bon-12.” The SI symbol for mole is mol, which is numerically identical to the traditional g mol. The SPE SI standard1 uses kmol as the unit for a mole where kmol designates “an amount of substance which contains as many kilograms (groups of molecules) as there are atoms in 12.0 kg (incorrectly written as 0.012 kg in the original SPE publication) of carbon-12 multiplied by the relative molecular mass of the substance involved.” A practical way to interpret kmol is “kg mol” where kmol is numerically equivalent to 1,000 g mol (i.e., 1,000 mol). Otherwise, the following conversions apply. 1 kmol
+ 1,000 mol + 1,000 g mol + 2.2046 lbm mol
1 lbm mol + 0.45359 kmol + 453.59 mol + 453.59 g mol 1 mol
+ 1 g mol + 0.001 kmol + 0.0022046 lbm mol
The term molecular weight has been replaced in the SI system by molar mass. Molar mass, M, is defined as the mass per mole (M+m/n) of a given substance where the unit mole must be consistent with the unit of mass. The numerical value of molecular weight is independent of the units used for mass and moles, as long as the units are consistent. For example, the molar mass of methane is 16.04, which for various units can be written M+ + + +
16.04 kg/kmol 16.04 lbm/lbm mol 16.04 g/g mol 16.04 g/mol
3.2.2 Critical and Reduced Properties. Most equations of state (EOS’s) do not use pressure and temperature explicitly to define the state of a system, but instead they generalize according to corresponding-states theory by use of two or more reduced properties, which are dimensionless.2 T r + TńT c , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.1a) PHASE BEHAVIOR
the following relation for volume fractions x vi, based on component densities at standard conditions ò i or specific gravities g i. x vi +
m ińò i
+
j
j
j+1
x i M ińg i
ȍ x M ńg j
j
j
x i M ińò i
ȍ x M ńò N
j
j
j
j+1
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.4)
N
j
+
N
j
j+1
+
n i M i ńò i
ȍ m ńò ȍ n M ńò N
j
j+1
Fig. 3.1—Reservoir densities as functions of pressure and temperature.
where the sum of x vi is unity. Having defined component fractions, we can introduce some common mixing rules for averaging the properties of mixtures. Kay’s5 mixing rule, the simplest and most widely used, is given by a mole-fraction average,
ȍz q . N
p r + pńp c , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.1b) V r + VńV c , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.1c) and ò r + òńò c, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.1d) where ò r + 1ńV r . Absolute units must be used when calculating reduced pressure and temperature. p c, T c, V c, and ò c are the true critical properties of a pure component, or some average for a mixture. In most petroleum engineering applications, the range of reduced pressure is from 0.02 to 30 for gases and 0.03 to 40 for oils; reduced temperature ranges from t1 to 2.5 for gases and from 0.4 to 1.1 for oils. Reduced density can vary from 0 at low pressures to about 3.5 at high pressures. Average mixture, or pseudocritical, properties are calculated from simple mixing rules or mixture specific gravity.3,4 Denoting a mixture pseudocritical property by q pc, the pseudoreduced property is defined q pr + qń q pc. Pseudocritical properties are not approximations of the true critical properties, but are chosen instead so that mixture properties will be estimated correctly with correspondingstates correlations. 3.2.3 Component Fractions and Mixing Rules. Petroleum reservoir mixtures contain hundreds of well-defined and “undefined” components. These components are quantified on the basis of mole, weight, and volume fractions. For a mixture having N components, i + 1, . . . , N, the overall mole fractions are given by zi +
ni
mi ń Mi
+
ȍ n ȍ m ńM N
N
j
j
j+1
,
. . . . . . . . . . . . . . . . . . . . . . . (3.2)
j
j+1
where n+moles, m+mass, M+molecular weight, and the sum of z i is 1.0. In general, oil composition is denoted by x i and gas composition by y i. Weight or mass fractions, wi , are given by wi +
mi
+
j+1
, . . . . . . . . . . . . . . . . . . . . . . . . (3.3)
N
j
j
i i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.5)
i+1
This mixing rule is usually adequate for molecular weight, pseudocritical temperature, and acentric factor.6 We can write a generalized linear mixing rule as
ȍf q N
i i
q+
i+1 N
ȍf
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.6) i
i+1
where f i is usually one of the following weighting factors: f i + z i, mole fraction (Kay’s rule); f i + w i , weight fraction; or f i + x vi, volume fraction. Depending on the quantity being averaged, other mixing rules and definitions of f i may be appropriate.7,8 For example, the mixing rules used for constants in an EOS (Chap. 4) can be chosen on the basis of statistical thermodynamics. 3.2.4 Volumetric Properties. Density, ò, is defined as the ratio of mass to volume, ò + mńV, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.7) expressed in such units as lbm/ft3, kg/m3, and g/cm3. Fig. 3.1 shows the magnitudes of density for reservoir mixtures. Molar density, ò M , gives the volume per mole: ò M + nńV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.8) Specific volume, v^, is defined as the ratio of volume to mass and is equal to the reciprocal of density. v^ + Vńm + 1ńò. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.9) Molar volume, v, defines the ratio of volume per mole, v + Vńn + Mńò + 1ńò M , . . . . . . . . . . . . . . . . . . . . . (3.10) and is typically used in cubic EOS’s. Molar density, ò M , is given by ò M + 1ńv + òńM, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.11)
n i Mi
ȍm ȍn M N
q+
j
j+1
where the sum of w i + 1.0. Although the composition of a mixture is usually expressed in terms of mole fraction, the measurement of composition is usually based on mass, which is converted to mole fraction with component molecular weights. For oil mixtures at standard conditions (14.7 psia and 60°F), the total volume can be approximated by the sum of the volumes of individual components, assuming ideal-solution mixing. This results in GAS AND OIL PROPERTIES AND CORRELATIONS
and is used in the formulas of some EOS’s. According to the SI standard, relative density replaces specific gravity as the term used to define the ratio of the density of a mixture to the density of a reference material. The conditions of pressure and temperature must be specified for both materials, and the densities of both materials are generally measured at standard conditions (standard conditions are usually 14.7 psia and 60°F). g+
ò ǒ p sc, T scǓ , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.12a) ò ref ǒ p sc, T scǓ 19
Fig. 3.2—Reservoir compressibilities as functions of pressure. Fig. 3.3—Reservoir FVF’s as functions of pressure.
ǒò oǓ sc go + , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.12b) ǒò wǓ sc
and g g +
ǒò gǓ sc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.12c) ǒò airǓ sc
Air is used as the reference material for gases, and water is used as the reference material for liquids. Specific gravity is dimensionless, although it is customary and useful to specify the material used as a reference (air+1 or water+1). In older references, liquid specific gravities are sometimes followed by the temperatures of both the liquid and water, respectively; for example, g o + 0.823 60ń60 , where the temperature units here are understood to be in degrees Fahrenheit. The oil gravity, g API, in degrees API is used to classify crude oils on the basis of the following relation,
B+
V mixture ǒ p, T Ǔ . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.16) V product ǒ p sc, T scǓ
The units of B are bbl/STB for oil and water, and ft3/scf or bbl/Mscf for gas. The surface product phase may consist of all or only part of the original mixture. Primarily, four volume factors are used in petroleum engineering. They are oil FVF, B o; water FVF, B w; gas FVF, B g; and total FVF of a gas/oil system, B t, where
g API + 141.5 g * 131.5 . . . . . . . . . . . . . . . . . . . . . . . . . . (3.13a)
Bo +
Vo V + o , . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.17a) Vo (V o) sc
141.5 , . . . . . . . . . . . . . . . . . . . . . . . . (3.13b) g API ) 131.5
Bw +
Vw V + w , . . . . . . . . . . . . . . . . . . . . . . . . . . (3.17b) Vw (V w) sc
o
and g o +
where g o +oil specific gravity (water+1). Officially, the SPE does not recognize g API in its SI standard, but because oil gravity (in degrees API) is so widely used (and understood) and because it is found in many property correlations, its continued use is justified for qualitative description of stock-tank oils. Isothermal compressibility, c, of a fixed mass of material is defined as
ǒ Ǔ
c + * 1 ēV V ēp
ǒ Ǔ
+ * 1^ ēv v ēp T ^
T
ǒ Ǔ,
+ * 1v ēv ēp
. . . . . (3.14)
T
where the units are psi*1 or kPa*1. In terms of density, ò, and FVF, B, isothermal compressibility is given by
ǒ Ǔ
1 ēò c+ò ēp
T
ǒ Ǔ,
+ 1 ēB B ēp
. . . . . . . . . . . . . . . . . . . . . (3.15)
T
where B is defined in the next section. Fig. 3.2 shows the variation in compressibility with pressure for typical reservoir mixtures. A discontinuity in oil compressibility occurs at the bubblepoint because gas comes out of solution. When two or more phases are present, a total compressibility is useful.8,9 3.2.5 Black-Oil Pressure/Volume/Temperature (PVT) Properties. The FVF, B; solution gas/oil ratio, R s ; and solution oil/gas ratio, r s, are volumetric ratios used to simplify engineering calculations. Specifically, they allow for the introduction of surface volumes of gas, oil, and water into material-balance equations. These are not standard engineering quantities, and they must be defined precisely. These properties constitute the black-oil or “beta” PVT formula used in petroleum engineering. Chap. 7 gives a detailed discussion of black-oil properties. 20
FVF, or simply volume factor, is used to convert a volume at elevated pressure and temperature to surface volume, and vice versa. More specifically, FVF is defined as the volume of a mixture at specified pressure and temperature divided by the volume of a product phase measured at standard conditions,
Bg +
Vg
ǒV gǓ
and B t +
+ sc
Vg , . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.17c) Vg
Vo ) Vg Vo ) Vg Vt + + ; . . . . . . . . . . . (3.17d) Vo (V o) sc (V o) sc
and the total FVF of a gas/water system is B tw +
Vg ) Vw Vt + . . . . . . . . . . . . . . . . . . . . . . . (3.17e) Vw (V w) sc
In Eq. 3.17, V o +oil volume at p and T ; V g +gas volume at p and T ; V w +water/brine volume at p and T ; V o +(V o) sc +stock-tankoil volume at standard conditions; V w + (V w) sc +stock-tank-water volume at standard conditions; and V g + ǒV gǓ sc+surface-gas volume at standard conditions. Because gas FVF is inversely proportional to pressure, a reciprocal gas volume factor, b g (equal to 1/ B g), is sometimes used, where the units of b g may be scf/ft3 or Mscf/bbl. Fig. 3.3 shows FVF’s of typical reservoir systems. Inverse oil FVF, b o (equal to 1/ B o) is also used in reservoir simulation. Wet gas and gas-condensate reservoir fluids produce liquids at the surface, and for these gases the surface product (separator gas) consists of only part of the original reservoir gas mixture. Two gas FVF’s are used for these systems: the “dry” FVF, B gd, and the “wet” FVF, B gw (or just B g). B gd gives the ratio of reservoir gas volume to the actual surface separator gas. B gw gives the ratio of reservoir gas volume to a hypothetical “wet” surface-gas volume (the actual separator-gas volume plus the stock-tank condensate converted to an equivalent surface-gas volume). Chap. 7 describes when B gd and B gw are used. The standard definition of B g + (p scńT sc)(ZTńp) (see Eq. 3.38) represents the wet-gas FVF. PHASE BEHAVIOR
Fig. 3.4—Solution gas/oil ratios for brine, Rsw , and reservoir oils, Rs , and inverse solution oil/gas ratio for reservoir gases, 1/rs , as functions of pressure.
When a reservoir mixture produces both surface gas and oil, the GOR, R go, defines the ratio of standard gas volume to a reference oil volume (stock-tank- or separator-oil volume),
ǒV gǓ
V + g . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.18a) R go + Vo (V o) sc and R sp +
sc
ǒV gǓ
sc
(V o) sp
+
Vg (V o) sp
. . . . . . . . . . . . . . . . . . . . . . (3.18b)
in units of scf/STB and scf/bbl, respectively. The separator conditions should be reported when separator GOR is used. Solution gas/oil ratio, R s , is the volume of gas (at standard conditions) liberated from a single-phase oil at elevated pressure and temperature divided by the resulting stock-tank-oil volume, with units scf/STB. R s is constant at pressures greater than the bubblepoint and decreases as gas is liberated at pressures below the bubblepoint. The producing GOR, R p, defines the instantaneous ratio of the total surface-gas volume produced divided by the total stock-tank-oil volume. At pressures greater than bubblepoint, R p is constant and equal to R s at bubblepoint. At pressures less than the bubblepoint, R p may be equal to, less than, or greater than the R s of the flowing reservoir oil. Typically, R p will increase 10 to 20 times the initial R s because of increasing gas mobility and decreasing oil mobility during pressure depletion. The surface volume ratio for gas condensates is usually expressed as an oil/gas ratio (OGR), r og. r og +
(V o) sc
ǒV gǓ
sc
+
Vo + 1 . . . . . . . . . . . . . . . . . . . . . . . (3.19) Vg R go
The unit for r og is STB/scf or, more commonly, “barrels per million” (STB/MMscf). To avoid misinterpretation, it should be clearly specified whether the OGR includes natural gas liquids (NGL’s) in addition to stock-tank condensate. In most petroleum engineering calculations, NGL’s are not included in the OGR. The ratio of surface oil to surface gas produced from a singlephase reservoir gas is referred to as the solution oil/gas ratio, r s. At pressures above the dewpoint, the producing OGR, r p is constant and equal to r s at the dewpoint. At pressures below the dewpoint, r p is typically equal to or just slightly greater than r s; the contribution of flowing reservoir oil to surface-oil production is negligible in most gas-condensate reservoirs. In the definitions of R p and r p, the total producing surface-gas volume equals the surface gas from the reservoir gas plus the solution gas from the reservoir oil; likewise, the total producing surface oil equals the stock-tank oil from the reservoir oil plus the condensate from the reservoir gas. Fig. 3.4 shows the behavior of R p, R s , and 1ńr s as a function of pressure. GAS AND OIL PROPERTIES AND CORRELATIONS
Fig. 3.5—Reservoir viscosities as functions of pressure.
3.2.6 Viscosity. Two types of viscosity are used in engineering calculations: dynamic viscosity, m, and kinematic viscosity, n. The definition of m for Newtonian flow (which most petroleum mixtures follow) is m+
tg c , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.20) duńdy
where t+shear stress per unit area in the shear plane parallel to the direction of flow, du/dy+velocity gradient perpendicular to the plane of shear, and g c +a units conversion from mass to force. The two viscosities are related by density, where m+n ò. Most petroleum engineering applications use dynamic viscosity, which is the property reported in commercial laboratory studies. The unit of dynamic viscosity is centipoise (cp), or in SI units, mPa@s, where 1 cp+1 mPa@s. Kinematic viscosity is usually reported in centistoke (cSt), which is obtained by dividing m in cp by ò in g/cm3; the SI unit for n is mm2/s, which is numerically equivalent to centistoke. Fig. 3.5 shows oil, gas, and water viscosities for typical reservoir systems. 3.2.7 Diffusion Coefficients. In the absence of bulk flow, components in a single-phase mixture are transported according to gradients in concentration (i.e., chemical potential). Fick’s10 law for 1D molecular diffusion in a binary system is given by u i + * D i j ǒdC ińd xǓ , . . . . . . . . . . . . . . . . . . . . . . . . . . (3.21) where u i +molar velocity of Component i; D ij +binary diffusion coefficient; and C i +molar concentration of Component i + y iò M, where y i +mole fraction; and x+distance. Eq. 3.21 clearly shows that mass transfer by molecular diffusion can be significant for three reasons: (1) large diffusion coefficients, (2) large concentration differences, and (3) short distances. A combination of moderate diffusion coefficients, concentration gradients, and distance may also result in significant diffusive flow. Molecular diffusion is particularly important in naturally fractured reservoirs11,12 because of relatively short distances (e.g., small matrix block sizes). Low-pressure binary diffusion coefficients for gases, D oij , are independent of composition and can be calculated accurately from fundamental gas theory (Chapman and Enskog6), which are basically the same relations used to estimate low-pressure gas viscosity. No well-accepted method is available to correct D oij for mixtures at high pressure, but two types of corresponding-states correlations have been proposed: D ij + D oij f(T r, p r) and D ij + D oij f(ò r). At low pressures, diffusion coefficients are several orders of magnitude smaller in liquids than in gases. At reservoir conditions, the difference between gas and liquid diffusion coefficients may be less than one order of magnitude. 3.2.8 IFT. Interfacial forces act between equilibrium gas, oil, and water phases coexisting in the pores of a reservoir rock. These forces 21
are generally quantified in terms of IFT, s; units of s are dynes/cm (or equivalently, mN/m). The magnitude of IFT varies from [50 dynes/cm for crude-oil/gas systems at standard conditions to t0.1 dyne/cm for high-pressure gas/oil mixtures. Gas/oil capillary pressure, P c, is usually considered proportional to IFT according to the Young-Laplace equation P c + 2sńr, where r is an average pore radius.13-15 Recovery mechanisms that are influenced by capillary pressure (e.g., gas injection in naturally fractured reservoirs) will necessarily be sensitive to IFT. 3.3 Gas Mixtures This section gives correlations for PVT properties of natural gases, including the following. 1. Review of gas volumetric properties. 2. Z-factor correlations. 3. Gas pseudocritical properties. 4. Wellstream gravity of wet gases and gas condensates. 5. Gas viscosity. 6. Dewpoint pressure. 7. Total volume factor. 3.3.1 Review of Gas Volumetric Properties. The properties of gas mixtures are well understood and have been accurately correlated for many years with graphical charts and EOS’s based on extensive experimental data.16-19 The behavior of gases at low pressures was originally quantified on the basis of experimental work by Charles and Boyle, which resulted in the ideal-gas law,3 pV + nRT, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.22) where R is the universal gas constant given in Appendix A for various units (Table A-2). In customary units, R + 10.73146
psia ft 3 , . . . . . . . . . . . . . . . . . . (3.23) ° R lbm mol
while for other units, R can be calculated from the relation
ǒ ǓǒT°R Ǔǒ Ǔǒmlbm Ǔ .
p R + 10.73146 unit psia
unit
V unit ft 3
unit
. . . . . . . . (3.24)
For example, the gas constant for SPE-preferred SI units is given by
ǒ
kPa 6.894757 psia
R + 10.73146
ǒ
3 0.02831685 m3 ft
Ǔ ǒ
Ǔ
ǒ1.8 °R Ǔ K
2.204623 lbm kg
Ǔ
kPa @ m 3 + 8.3143 . . . . . . . . . . . . . . . . . . . . . . . . . (3.25) K @ kmol The gas constant can also be expressed in terms of energy units (e.g., R+8.3143 J/mol@K); note that J+N@m+(N/m2) m3+Pa@m3. In this case, the conversion from one unit system to another is given by R + 8.3143
ǒEJ ǓǒTK Ǔǒmg Ǔ . unit
unit
unit
+
10.73146(60 ) 459.67) 14.7
+ 379.4 scfńlbm mol + 23.69 std m 3ńkmol .
. . . . . . . . . . . . . . . . . . . (3.27)
Second, the specific gravity of a gas directly reflects the gas molecular weight at standard conditions, gg +
ǒò gǓ Mg Mg sc + + ǒò airǓ M air 28.97 sc
and M g + 28.97 g g .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.28)
For gas mixtures at moderate to high pressure or at low temperature the ideal-gas law does not hold because the volume of the constituent molecules and their intermolecular forces strongly affect the volumetric behavior of the gas. Comparison of experimental data for real gases with the behavior predicted by the ideal-gas law shows significant deviations. The deviation from ideal behavior can be expressed as a factor, Z, defined as the ratio of the actual volume of one mole of a real-gas mixture to the volume of one mole of an ideal gas, Z+
volume of 1 mole of real gas at p and T , volume of 1 mole of ideal gas at p and T . . . . . . . . . . . . . . . . . . . . (3.29)
where Z is a dimensionless quantity. Terms used for Z include deviation factor, compressibility factor, and Z factor. Z factor is used in this monograph, as will the SPE reserve symbol Z (instead of the recommended SPE symbol z) to avoid confusion with the symbol z used for feed composition. From Eqs. 3.22 and 3.29, we can write the real-gas law including the Z factor as pV + nZRT, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.30) which is the standard equation for describing the volumetric behavior of reservoir gases. Another form of the real-gas law written in terms of specific volume ( v^ + 1ńò) is pv^ + ZRTńM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.31) or, in terms of molar volume (v + Mńò), pv + ZRT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.32) Z factor, defined by Eq. 3.30, Z + pVńnRT, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.33) is used for both phases in EOS applications (see Chap. 4). In this monograph we use both Z and Z g for gases and Z o for oils; Z without a subscript always implies the Z factor of a “gas-like” phase. All volumetric properties of gases can be derived from the realgas law. Gas density is given by ò g + pM gńZRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.34)
. . . . . . . . . . . . . . . . (3.26)
An ideal gas is a hypothetical mixture with molecules that are negligible in size and have no intermolecular forces. Real gases mimic the behavior of an ideal gas at low pressures and high temperatures because the mixture volume is much larger than the volume of the molecules making up the mixture. That is, the mean free path between molecules that are moving randomly within the total volume is very large and intermolecular forces are thus very small. Most gases at low pressure follow the ideal-gas law. Application of the ideal-gas law results in two useful engineering approximations. First, the standard molar volume representing the volume occupied by one mole of gas at standard conditions is independent of the gas composition. 22
ǒV Ǔ sc ǒv gǓ + v g + ng sc + RT p sc sc
or, in terms of gas specific gravity, by p gg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.35) ZRT For wet-gas and gas-condensate mixtures, wellstream gravity, g w, must be used instead of g g in Eq. 3.35.3 Gas density may range from 0.05 lbm/ft3 at standard conditions to 30 lbm/ft3 for highpressure gases. Gas molar volume, v g , is given by ò g + 28.97
v g + ZRTńp,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.36)
where typical values of v g at reservoir conditions range from 1 to 1.5 ft3/lbm mol compared with 379 ft3/lbm mol for gases at standard conditions. In Eqs. 3.30 through 3.36, R+universal gas constant. PHASE BEHAVIOR
Pseudoreduced Temperature
1 January 1941
Fig. 3.6—Standing-Katz4 Z-factor chart.
Gas compressibility, c g , is given by
ǒ Ǔ
ēV g cg + * 1 V g ēp
ǒ Ǔ
+ 1p * 1 ēZ Z ēp
. . . . . . . . . . . . . . . . . . . . . . . . . . . (3.37) T
For sweet natural gas (i.e., not containing H2S) at pressures less than [1,000 psia, the second term in Eq. 3.37 is negligible and c g + 1ńp is a reasonable approximation. Gas volume factor, B g, is defined as the ratio of gas volume at specified p and T to the ideal-gas volume at standard conditions, Bg +
ǒTp Ǔ ZTp . sc
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.38)
sc
For customary units ( psc +14.7 psia and Tsc +520°R), this is B g + 0.02827 ZT p , . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.39) with temperature in °R and pressure in psia. This definition of B g assumes that the gas volume at p and T remains as a gas at standard conditions. For wet gases and gas condensates, the surface gas will not contain all the original gas mixture because liquid is produced GAS AND OIL PROPERTIES AND CORRELATIONS
after separation. For these mixtures, the traditional definition of B g may still be useful; however, we refer to this quantity as a hypothetical wet-gas volume factor, B gw, which is calculated from Eq. 3.38. Because B g is inversely proportional to pressure, the inverse volume factor, b g + 1ńB g , is commonly used. For field units, p . . . . . . . . . . . . . . . . . . . . . . (3.40a) ZT p . . . . . . . . . . . . . . . (3.40b) and b g in Mscfńbbl + 0.1985 ZT b g in scfńft 3 + 35.37
If the reservoir gas yields condensate at the surface, the dry-gas volume factor, B gd, is sometimes used.20 B gd +
ǒTp ǓǒZTpǓǒF1 Ǔ, sc
sc
. . . . . . . . . . . . . . . . . . . . . . . (3.41)
gg
where F gg+ratio of moles of surface gas, n g , to moles of wellstream mixture (i.e., reservoir gas, n g); see Eqs. 7.10 and 7.11 of Chap. 7. 3.3.2 Z-Factor Correlations. Standing and Katz4 present a generalized Z-factor chart (Fig. 3.6), which has become an industry standard for predicting the volumetric behavior of natural gases. Many empirical equations and EOS’s have been fit to the original Standing-Katz chart. For example, Hall and Yarborough21,22 present an 23
accurate representation of the Standing-Katz chart using a Carnahan-Starling hard-sphere EOS, Z + ap prńy, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.42) where a + 0.06125 t exp[* 1.2(1 * t) 2], where t + 1ńT pr. The reduced-density parameter, y (the product of a van der Waals covolume and density), is obtained by solving f( y) + 0 + * ap pr )
y ) y2 ) y3 * y4 (1 * y) 3
* (14.76t * 9.76t 2 ) 4.58t 3)y 2 ) (90.7t–242.2t 2 ) 42.4t 3)y 2.18)2.82 t, with
* 1 ) 4y ) df(y) + dy (1 * y) 4 4y 2
4y 3
)
. . . . . . . . . (3.43)
y4
* (29.52t * 19.52t 2) 9.16t 3)y ) (2.18 ) 2.82t)(90.7t * 242.2t 2 ) 42.4t 3) y 1.18)2.82 t .
. . . . . . . . . . . . . . . . . . . . . . . . . (3.44)
The derivative ēZ/ēp used in the definition of c g is given by
ǒēZēpǓ
+ pa T
pc
ap ńy ƪ1y * df(y)ńdy ƫ . . . . . . . . . . . . . . . . . . . . (3.45) pr
2
An initial value of y+0.001 can be used with a Newton-Raphson procedure, where convergence should be obtained in 3 to 10 iterations for Ťf( y)Ť + 1 10 *8. On the basis of Takacs’23 comparison of eight correlations representing the Standing-Katz4 chart, the Hall and Yarborough21 and the Dranchuk and Abou-Kassem24 equations give the most accurate representation for a broad range of temperatures and pressures. Both equations are valid for 1 x T r x 3 and 0.2 x p r x 25 to 30. For many petroleum engineering applications, the Brill and Beggs25 equation gives a satisfactory representation ("1 to 2%) of the original Standing-Katz Z-factor chart for 1.2 t T r t 2. Also, this equation can be solved explicitly for Z. The main limitations are that reduced temperature must be u1.2 ([80°F) and t2.0 ([340°F) and reduced pressure should be t15 ([10,000 psia). The Standing and Katz Z-factor correlation may require special treatment for wet gas and gas-condensate fluids containing significant amounts of heptanes-plus material and for gas mixtures with significant amounts of nonhydrocarbons. An apparent discrepancy in the Standing-Katz Z-factor chart for 1.05 t T r t 1.15 has been “smoothed” in the Hall-Yarborough21 correlations. The Hall and Yarborough (or Dranchuk and Abou-Kassem24) equation is recommended for most natural gases. With today’s computing capabilities, choosing simple, less-reliable equations, such as the Brill and Beggs25 equation, is normally unnecessary. The Lee-Kesler,26,27 AGA-8,28 and DDMIX29 correlations for Z factor were developed with multiconstant EOS’s to give accurate volumetric predictions for both pure components and mixtures. They require more computation but are very accurate. These equations are particularly useful in custody-transfer calculations. They also are required for gases containing water and concentrations of nonhydrocarbons that exceed the limits of the Wichert and Aziz method.30,31 3.3.3 Gas Pseudocritical Properties. Z factor, viscosity, and other gas properties have been correlated accurately with correspondingstates principles, where the property is correlated as a function of reduced pressure and temperature. Z + fǒ p r , T rǓ and m g ńm gsc + fǒ p r , T rǓ, . . . . . . . . . . . . . . . . . . . . . . . . . (3.46) 24
Fig. 3.7—Gas pseudocritical properties as functions of specific gravity.
where p r + pńp c and T r + TńT c. Such corresponding-states relations should be valid for most pure compounds when component critical properties p c and T c are used. The same relations can be used for gas mixtures if the mixture pseudocritical properties p pc and T pc are used. Pseudocritical properties of gases can be estimated with gas composition and mixing rules or from correlations based on gas specific gravity. Sutton7 suggests the following correlations for hydrocarbon gas mixtures. T pcHC + 169.2 ) 349.5g gHC * 74.0 g 2gHC . . . . . . . . . . . (3.47a) and p pcHC + 756.8 * 131g gHC * 3.6g 2gHC . . . . . . . . . . . (3.47b) He claims that Eqs. 3.47a and 3.47b are the most reliable correlations for calculating pseudocritical properties with the Standing-Katz Z-factor chart. He even claims that this method is superior to the use of composition and mixing rules. Standing3 gives two sets of correlations: one for dry hydrocarbon gases ( g gHC t 0.75), T pcHC + 168 ) 325g gHC * 12.5g 2gHC . . . . . . . . . . . . . . (3.48a) and p pcHC + 667 ) 15.0 g gHC * 37.5g 2gHC , . . . . . . . . . . (3.48b) and one for wet-gas mixtures ( g gHC y 0.75), T pcHC + 187 ) 330 g gHC * 71.5g 2gHC . . . . . . . . . . . . . . (3.49a) and p pcHC + 706 * 51.7g gHC * 11.1g 2gHC . . . . . . . . . . . (3.49b) The Standing correlations are used extensively in the industry; Fig. 3.7 compares them with the Sutton correlations. The Sutton and the Standing wet-gas correlations for T pc give basically the same results, whereas the three p pc correlations are quite different at g g u 0.85. Kay’s5 mixing rule is typically used when gas composition is available.
ȍy M , N
M+
i
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.50a)
i+1
PHASE BEHAVIOR
ƪǒ
and å + 120 y CO ) y H
ǒ
2
4 ) 15 y 0.5 H S * yH 2
2S
2S
Ǔ
Ǔ,
0.9
ǒ
* y CO ) y H 2
2S
Ǔ ƫ 1.6
. . . . . . . . . . . . . . . . . . . . . . . (3.52c)
* and p * are mixture pseudocriticals based on Kay’s mixwhere T pc pc ing rule. This method was developed from extensive data from natural gases containing nonhydrocarbons, with CO2 molar concentration ranging from 0 to 55% and H2S molar concentrations ranging from 0 to 74%. If only gas gravity and nonhydrocarbon content are known, the hydrocarbon specific gravity is first calculated from
ǒ
Ǔ
g g * y N M N ) y CO M CO )y H S M H S ńM air 2 2 2 2 2 2 . g gHC + 1 * y N * y CO * y H S 2
2
2
. . . . . . . . . . . . . . . . . . . . (3.53) Hydrocarbon pseudocriticals are then calculated from Eqs. 3.47a and 3.47b, and these values are adjusted for nonhydrocarbon content on the basis of Kay’s5 mixing rule.
ǒ
p *pc + 1 * y N * y CO * y H 2
2
2S
Ǔp
pcHC
) y N p cN ) y CO p c CO ) y H S p cH 2
Fig. 3.8—Heptanes-plus (pseudo)critical properties recommended for reservoir gases (from Standing,33 after Matthews et al.32).
2
ȍy T N
i
ci , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.50b)
i+1
ȍy p N
and p pc +
i
ci ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.50c)
i+1
where the pseudocritical properties of the C7+ fraction can be estimated from the Matthews et al.32 correlations (Fig. 3.8),3 Tc C
7)
+ 608 ) 364 logǒ M C ) ǒ2, 450 log M C
and p c C
7)
7)
7)
* 71.2 Ǔ
* 3, 800Ǔ log g C
+ 1, 188 * 431 logǒ M C
ƪ
7)
7)
. . . . . . (3.51a)
* 61.1 Ǔ
) 2, 319 * 852 logǒ M C * 53.7 Ǔ 7)
ƫǒg
C 7)*
0.8 Ǔ.
. . . . . . . . . . . . . . . . . . . (3.51b) Kay’s mixing rule is usually adequate for lean natural gases that contain no nonhydrocarbons. Sutton suggests that pseudocriticals calculated with Kay’s mixing rule are adequate up to g g [ 0.85, but that errors in calculated Z factors increase linearly at higher specific gravities, reaching 10 to 15% for g g u 1.5. This bias may be a result of the C7+ critical-property correlations used by Sutton (not Eqs. 3.51a and 3.51b). When significant quantities of CO2 and H2S nonhydrocarbons are present, Wichert and Aziz33,31 suggest corrections to arrive at pseudocritical properties that will yield reliable Z factors from the Standing-Katz chart. The Wichert and Aziz corrections are given by * * å , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.52a) T pc + T pc
p pc +
p *pcǒ Tpc* * å Ǔ * T pc ) yH
2S
ǒ1 * y Ǔå
, . . . . . . . . . . . . . . . . . (3.52b)
H 2S
GAS AND OIL PROPERTIES AND CORRELATIONS
2
2
2S
. . . . . . . . . . (3.54a)
and T *pc + (1 * y N * y CO * y H S)T pcHC 2
2
2
) y N T cN ) y CO T c CO ) y H S T cH S . 2
T pc +
2
2
2
2
2
2
. . . . (3.54b)
T c* and p *c are used in the Wichert-Aziz equations with CO2 and H2S mole fractions to obtain mixture T pc and p pc. The Sutton7 correlations (Eqs. 3.47a and 3.47b) are recommended for hydrocarbon pseudocritical properties. If composition is available, Kay’s mixing rule should be used with the Matthews et al.32 pseudocriticals for C7+. Gases containing significant amounts of CO2 and H2S nonhydrocarbons should always be corrected with the Wichert-Aziz equations. Finally, for gas-condensate fluids the wellstream specific gravity, g w (discussed in the next section), should replace g g in the equations above. 3.3.4 Wellstream Specific Gravity. Gas mixtures that produce condensate at surface conditions may exist as a single-phase gas in the reservoir and production tubing. This can be verified by determining the dewpoint pressure at the prevailing temperature. If wellstream properties are desired at conditions where the mixture is single-phase, surface-gas and -oil properties must be converted to a wellstream specific gravity, g w. This gravity should be used instead of g g to estimate pseudocritical properties. Wellstream gravity r p represents the average molecular weight of the produced mixture (relative to air) and is readily calculated from the producing-oil (condensate)/gas ratio, r p; average surface-gas gravity g g ; surface-condensate gravity, g o ; and surface-condensate molecular weight M o . gw +
g g ) 4, 580 r p g o , . . . . . . . . . . . . . . . . . . . (3.55) 1 ) 133, 000 r p ǒ gńM Ǔ o
with r p in STB/scf. Average surface-gas gravity is given by N sp
ȍR gg +
pi g gi
i+1 N sp
ȍR
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.56) pi
i+1
where R pi +GOR of Separator Stage i. Standing33 presents Eq. 3.55 graphically in Fig. 3.9. When M o is not available, Standing gives the following correlation. 25
Solution Gas/Oil Ratio, scf/STB
Oil/Gas Ratio, STB/MMscf
Fig. 3.9—Wellstream gravity relative to surface average gas gravity as a function of solution oil/gas ratio and surface gravities.
M o + 240 * 2.22 g API . . . . . . . . . . . . . . . . . . . . . . . . . (3.57) This relation should not be extrapolated outside the range 45 t g API t 60. Eilerts34 gives a relation for ( gńM) o , ǒ gńMǓ + ǒ1.892 o * ǒ4.52
10 *3Ǔ ) ǒ7.35
10 *5Ǔg API
2 10 *8Ǔg API , . . . . . . . . . . . . . . . . . . . (3.58)
which should be reliable for most condensates. When condensate molecular weight is not available, the recommended correlation for M o is the Cragoe35 correlation, Mo +
6, 084 , g API * 5.9
. . . . . . . . . . . . . . . . . . . . . . . . . . (3.59)
which gives reasonable values for all surface condensates and stock-tank oils. A typical problem that often arises in the engineering of gas-condensate reservoirs is that all the data required to calculate wellstream gas volumes and wellstream specific gravity are not available and must be estimated.36-38 In practice, we often report only the first-stage-separator GOR (relative to stock-tank-oil volume) and gas specific gravity, R s1 and g g1, respectively; the stock-tank-oil gravity, g o ; and the primary-separator conditions, p sp1 and T sp1. To calculate g w from Eq. 3.55 we need total producing OGR, r p, which equals the inverse of R s1 plus the additional gas that will be released from the first-stage separator oil, R s), rp +
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.60) ǒR s1 ) R s)Ǔ
R s) can be estimated from several correlations.37,39 Whitson38 proposes use of a bubblepoint pressure correlation (e.g., the Standing40 correlation), R s) + A 1g g) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.61a) and A 1 +
p ƪǒ18.2 ) 1.4 Ǔ10 ǒ sp1
0.0125g API*0.00091T sp1
Ǔ
ƫ
,
with p sp1 in psia, T sp1 in °F, and R s) in scf/STB. g g) is the gas gravity of the additional solution gas released from the separator oil. The Katz41 correlation (Fig. 3.10) can be used to estimate g g), where a best-fit representation of his graphical correlation is . . . . . . . . . . . . . . . . . . . . . . . . . . (3.62)
where A 2 + 0.25 ) 0.02g API and A 3 + * (3.57 26
Solving Eqs. 3.61 and 3.62 for R s) gives R s) +
A1 A2 ǒ1 * A 1 A 3Ǔ
10 *6)g API .
.
. . . . . . . . . . . . . . . . . . . . . . . . . . (3.63)
Average surface separator gas gravity, g g, is given by gg +
g g1 R s1 ) g g) R s) . R s1 ) R s)
. . . . . . . . . . . . . . . . . . . . . . (3.64)
Although the Katz correlation is only approximate, the impact of a few percent error in g g) is not of practical consequence to the calculation of g w because R s) is usually much less than R s1 . 3.3.5 Gas Viscosity. Viscosity of reservoir gases generally ranges from 0.01 to 0.03 cp at standard and reservoir conditions, reaching up to 0.1 cp for near-critical gas condensates. Estimation of gas viscosities at elevated pressure and temperature is typically a two-step procedure: (1) calculating mixture low-pressure viscosity m gsc at p sc and T from Chapman-Enskog theory3,6 and (2) correcting this value for the effect of pressure and temperature with a corresponding-states or dense-gas correlation. These correlations relate the actual viscosity m g at p and T to low-pressure viscosity by use of the ratio m gńm gsc or difference ( m g * m gsc) as a function of pseudoreduced properties p pr and T pr or as a function of pseudoreduced density ò pr. Gas viscosities are rarely measured because most laboratories do not have the required equipment; thus, the prediction of gas viscosity is particularly important. Gas viscosity of reservoir systems is often estimated from the graphical correlation m gńm gsc + f(T r, p r) proposed by Carr et al.42 (Fig. 3.11). Dempsey43 gives a polynomial approximation of the Carr et al. correlation. With these correlations, gas viscosities can be estimated with an accuracy of about "3% for most applications. The Dempsey correlation is valid in the range 1.2 x T r x 3 and 1 x p r x 20. The Lee-Gonzalez gas viscosity correlation (used by most PVT laboratories when reporting gas viscosities) is given by44
1.205
. . . . . . . . . . . . . . . . . . . (3.61b)
g g) + A 2 ) A 3 R s) ,
Fig. 3.10—Correlation for separator-oil dissolved gas gravity as a function of stock-tank-oil gravity and separator-oil GOR (from Ref. 41).
mg + A1 where A 1 +
10 *4 expǒA 2 ò g 3Ǔ , A
. . . . . . . . . . . . . . . . . . (3.65a)
ǒ9.379 ) 0.01607M gǓT 1.5 209.2 ) 19.26M g ) T
,
A 2 + 3.448 ) ǒ986.4ńTǓ ) 0.01009M g , and A 3 + 2.447 * 0.2224A 2 , . . . . . . . . . . . . . . . . . . . . (3.65b) with m g in cp, ò g in g/cm3, and T in °R. McCain19 indicates the accuracy of this correlation is 2 to 4% for gg t1.0, with errors up to 20% for rich gas condensates with g g u 1.5. PHASE BEHAVIOR
Gas Gravity (air+1)
N2, mol%
CO2, mol%
H2S, mol%
g
o
Molecular Weight
Pseudoreduced Temperature, Tr Fig. 3.11—Carr et al.42 gas-viscosity correlation.
Lucas45 proposes the following gas viscosity correlation, which is valid in the range 1 t T r t 40 and 0 t p r t 100 (Fig. 3.12)6: m gńm gsc + 1 )
A 2 p pr5 ) ǒ1 ) A 3 p pr4Ǔ *1
(1.245
where A 1 +
A 1 p 1.3088 pr
A
10 *3)
A
,
expǒ T pr
. . . . . . . (3.66a)
5.1726T *0.3286 pr
Ǔ 0.4489 expǒ3.0578T *37.7332 pr , T pr
A4 +
Ǔ 1.7368 expǒ2.2310T *7.6351 pr , T pr
Ǔ
,
where m gsc c + ƪ0.807T pr0.618 * 0.357 expǒ* 0.449T prǓ ) 0.340 expǒ* 4.058T prǓ ) 0.018ƫ ,
,
N
i
and A 5 + 0.9425 expǒ* 0.1853T pr0.4489Ǔ , . . . . . . . . . . . (3.66b)
GAS AND OIL PROPERTIES AND CORRELATIONS
ȍy Z and p pc + RT pc
A 2 + A 1ǒ1.6553T pr * 1.2723Ǔ , A3 +
ǒ Ǔ
1ń6
T pc c + 9, 490 M 3p 4pc
ci
i+1 N
ȍy v
,
. . . . . . . . . . . . . . . . . . . . . . . . (3.67)
i ci
i+1
with c in cp*1, T and T c in °R, and p c in psia. Special corrections should be applied to the Lucas correlation when polar compounds, such as H2S and water, are present in a gas mixture. The effect of H2S is always t1% and can be neglected, and appropriate corrections can be made to treat water if necessary. Given its wide range of applicability, the Lucas method is recommended for general use. When compositions are not available, correlations for pseudocritical properties in terms of specific gravity can be used instead. Standing2 gives equations for m gsc in terms of g g, temperature, and nonhydrocarbon content, m gsc + ǒ m gscǓ uncorrected ) Dm N ) Dm CO ) Dm H S , 2
2
2
. . . . . . . . . . . . . . . . . . . . (3.68a) 27
) A 7ǒ z C pr +p/pc ; T/Tc ; h in mp 4 c+0.176(Tc /M3/pc )1/6; Tc in K, pc in bar
ȳ C 7) Ǔ 3) A ȱ 8 ȧ ȧ ȲǒgC7) ) 0.0001 Ǔȴ M
7)
ȱ ) Aȧ Ȳǒ g
MC
7)
ȳ )A ȱ ȧ ȧǒg ) 0.0001 Ǔȴ Ȳ 2
MC
9
7)
3
10
C 7)
ȳ ȧ ) 0.0001 Ǔȴ
MC C 7)
7)
) A 11 , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.69) where A1+*2.0623054, A2+6.6259728, A3+*4.4670559 10*3, A4+1.0448346 10*4, A5+3.2673714 10*2, A6+ *3.6453277 10*3, A7+7.4299951 10*5, A8+*1.1381195 10*1, A9+6.2476497 10*4, A10+*1.0716866 10*6, and A11+1.0746622 101. The range of properties used to develop this correlation includes dewpoints from 1,000 to 10,000 psia, temperatures from 40 to 320°F, and a wide range of reservoir compositions. The correlation usually can be expected to predict dewpoints with an accuracy of "10% for condensates that do not contain large amounts of nonhydrocarbons. This is acceptable in light of the fact that experimental dewpoint pressures are probably determined with an accuracy of only "5%. The correlation is generally used only for preliminary reservoir studies conducted before an experimental dewpoint is available. Organick and Golding50 and Kurata and Katz51 present graphical correlations for dewpoint pressure.
pr +0
pr +0
Fig. 3.12—Lucas45 corresponding-states generalized viscosity correlation (Ref. 6); h+dynamic viscosity and mp+micropoise+10*6 poise+10*4 cp.
3.3.7 Total FVF. Total FVF,3,17,46 B t, is defined as the volume of a two-phase, gas-oil mixture (or sometimes a single-phase mixture) at elevated pressure and temperature divided by the stock-tank-oil volume resulting when the two-phase mixture is brought to surface conditions, Bt +
10 *3Ǔ ) ƪǒ1.709
where ǒ m gscǓ uncorrected + ǒ8.188
10 *6Ǔg gƫT * ǒ6.15
* ǒ2.062
Dm N + y N ƪǒ8.48 2
Dm CO + y CO ƪǒ9.08 2
10 *3Ǔ log g g , 10 *3Ǔƫ,
10 *3Ǔ log g g ) ǒ9.59
2
10 *3Ǔƫ ,
10 *3Ǔ log g g ) ǒ6.24
2
and Dm H2S + y H 2Sƪǒ8.49
10 *5Ǔ
10 Ǔƫ.
10 Ǔ log g g ) ǒ3.73 *3
*3
. . . . . . . . . . . . . . . . . . . (3.68b) Reid et al.6 review other gas viscosity correlations with accuracy similar to that of the Lucas correlation. 3.3.6 Dewpoint Pressure. The prediction of retrograde dewpoint pressure is not widely practiced. It is generally recognized that the complexity of retrograde phase behavior necessitates experimental determination of the dewpoint condition. Sage and Olds’46 data are perhaps the most extensive tabular correlation of dewpoint pressures. Eilerts et al.47,48 also present dewpoint pressures for several light-condensate systems. Nemeth and Kennedy49 have proposed a dewpoint correlation based on composition and C7+ properties.
ƪ
ln p d+A 1 z C ) z CO ) z H S )z C )2(z C )z C ) ) z C 2
2
2
ƫ
) 0.4z C )0.2z N ) A 2 g C 1
) A 4T )ǒA 5z C 28
2
7)
MC
7)
3
6
ȱ ) Aȧ Ȳǒz
7)
4
ȳ ȧ ) 0.002 Ǔȴ zC
3
C 7)
5
Ǔ) A6ǒzC7)MC7)Ǔ2
1
Vo ) Vg Vo ) Vg + . . . . . . . . . . . . . . . . . . . . . . (3.70) Vo (V o) sc
B t is used for calculating the oil in place for gas-condensate reservoirs, where V o + 0 in Eq. 3.70. Assuming 1 res bbl of hydrocarbon PV, the initial condensate in place is given by N + 1ńB t (in STB) and the initial “dry” separator gas in place is G + Nńr p , where r p +initial producing (solution) OGR. For gas-condensate systems, Sage and Olds46 give a tabulated correlation for B t. R pT B t + p Z *,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.71)
where R p +producing GOR in scf/STB, B t is in bbl/STB, T is in °R, and p is in psia. Z* varies with pressure and temperature, where the tabulated correlation for Z* is well represented by p p 1.5 , . . . . . . . . (3.72) Z * + A 0 ) A 1p ) A 2p 1.5 ) A 3 ) A 4 T T * * 3 6 where A0+5.050 10 , A1+*2.740 10 , A2+3.331 10*8, A3+2.198 10*3, and A4+*2.675 10*5 with p in psia and T in °R. Although the Sage and Olds data only cover the range 600tpt3,000 psia and 100tTt250°F, Eq. 3.72 gives acceptable results up to 10,000 psia and 350°F (when gas volume is much larger than oil volume). When reservoir hydrocarbon volume consists only of gas, the following relations apply for total FVF. B t + B gd R p + B gw ǒR p ) C og Ǔ ,
. . . . . . . . . . . . . . . . . (3.73a)
C og + 133, 000 ǒg ońM oǓ , . . . . . . . . . . . . . . . . . . . . . . (3.73b) M o [ 6, 084ńǒ g API * 5.9Ǔ ,
. . . . . . . . . . . . . . . . . . . . . (3.73c)
and g API + 141.5ń(131.5 ) g o) ,
. . . . . . . . . . . . . . . . . (3.73d)
B gw +wet-gas FVF in ft3/scf where B gd +dry gas FVF in (given by Eq. 3.38), C og +gas equivalent conversion factor in scf/ STB (see Chap. 7), and R p +producing GOR in scf/STB. ft3/scf,
PHASE BEHAVIOR
PR EOS Glasø Uncorrected Glasø Corrected
C7+ Watson Characterization Factor, KwC7+
C7+ Watson Characterization Factor, KwC7+
Fig. 3.13—Effect of paraffinicity, Kw , on bubblepoint pressure.
Standing3 gives a graphical correlation for B t using a correlation parameter A defined as 0.5
A + R p T 0.3 g ao , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.74) gg where a + 2.9 10 *0.00027 Rp. Standing’s correlation is valid for both oil and gas-condensate systems and can be represented with log B t + * 5.262 *
47.4 , . . . . . . . . . (3.75a) * 12.22 ) log A *
matically.8 An accurate method is needed to correlate the bubblepoint pressure, temperature, and solution gas/oil ratio. Oil properties can be grouped into two categories: saturated and undersaturated properties. Saturated properties apply at pressures at or below the bubblepoint, and undersaturated properties apply at pressures greater than the bubblepoint. For oils with initial GOR’s less than [500 scf/STB, assuming linear variation of undersaturated-oil properties with pressure is usually acceptable.
. . (3.75b)
3.4.1 Bubblepoint Pressure. The correlation of bubblepoint pressure has received more attention than any other oil-property correlation. Standing3,17,40 developed the first accurate bubblepoint correlation, which was based on California crude oils.
and A is given by Eq. 3.74. On the basis of data from North Sea oils, Glasø52 gives a correlation for B t using the Standing correlation parameter A (Eq. 3.74):
p b + 18.2ǒ A * 1.4 Ǔ, . . . . . . . . . . . . . . . . . . . . . . . . . . (3.78) where A + ǒR ńg Ǔ 0.83 10 ǒ0.00091T*0.0125g APIǓ, with R in scf/STB, T
ǒ
where log A * + log A * 10.1 *
log B t + ǒ8.0135
96.8 6.604 ) log p
Ǔ
10 *2Ǔ ) 0.47257 log A *
) 0.17351ǒlog A * Ǔ 2 , . . . . . . . . . . . . . . . . . . . . . (3.76) where A*+A p*1.1089. Either the Standing or the Glasø correlations for B t can be used with approximately the same accuracy. However, neither correlation is consistent with the limiting conditions B t + B o for V g + 0 . . . . . . . . . . . . . . . . . . . . . . . . . . (3.77a)
s
s
g
in °F, and p b in psia. Lasater53 used a somewhat different approach to correlate bubblepoint pressure, where mole fraction y g of solution gas in the reservoir oil is used as the main correlating parameter17: p b + A gT , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.79) g
with T in °R and p b in psia. The function A( y g ) is given graphically by Lasater, and his correlation can be accurately described by A + 0.83918
; y g x 0.6 . . . . . . . . (3.80a) 10 1.17664yg y 0.57246 g
and B t + B gd R p for V o + 0. . . . . . . . . . . . . . . . . . . . (3.77b)
and A + 0.83918
B t correlations evaluated at a bubblepoint usually will underpredict the actual B ob by [0.2.
133, 000 ǒ gńMǓ o where y g + 1 ) Rs
3.4 Oil Mixtures This section gives correlations for PVT properties of reservoir oils, including bubblepoint pressure and oil density, compressibility, FVF, and viscosity. With only a few exceptions, oil properties have been correlated in terms of surface-oil and -gas properties, including solution gas/oil ratio, oil gravity, average surface-gas gravity, and temperature. A few correlations are also given in terms of composition and component properties. Reservoir oils typically contain dissolved gas consisting mainly of methane and ethane, some intermediates (C3 through C6), and lesser quantities of nonhydrocarbons. The amount of dissolved gas has an important effect on oil properties. At the bubblepoint a discontinuity in the system volumetric behavior is caused by gas coming out of solution, with the system compressibility changing draGAS AND OIL PROPERTIES AND CORRELATIONS
10 1.08000yg y 0.31109 ; y g u 0.6, . . . . . (3.80b) g
ƪ
ƫ
*1
, . . . . . . . . . . . . (3.81)
with R s in scf/STB. In this correlation, the gas mole fraction is dependent mainly on solution gas/oil ratio, but also on the properties of the stock-tank oil. The Cragoe35 correlation given by Eq. 3.59 is recommended for estimating M o when stock-tank-oil molecular weight is not known. Standing’s approach was used by Glasø52 for North Sea oils, resulting in the correlation log p b + 1.7669 ) 1.7447 log A * 0.30218(log A) 2 , . . . . . . . . . . . . . . . . . . . . (3.82)
ǒT Ǔ with p b in psia, T in °F and where A + ǒR sńg gǓ R s in scf/STB. Glasø’s corrections for nonhydrocarbon content and stock-tank-oil paraffinicity are not widely used, primarily be0.816
0.172
ńg 0.989 API
29
cause the necessary data are not available. Sutton and Farshad54 mention that the API correction for paraffinicity worsened bubblepoint predictions for gulf coast fluids. Fig. 3.13 gives an explanation for this observation. Fig. 3.13 shows the effect of paraffinicity (which is quantified by the Watson characterization factor, K w) on bubblepoint pressure; the figure is based on calculations with a tuned EOS for an Asian oil (solid circles). The oil composition is constant in the example calculation. The 12 C7+ fractions are each split into a paraffinic pseudocomponent and an aromatic pseudocomponent (i.e., 24 C7+ pseudocomponents). The paraffinic fraction was varied, and bubblepoint calculations were made. The variation in paraffinicity is expressed in terms of the overall C7+ Watson characterization factor. Also shown in the figure are the variation in solution gas/oil ratio and the oil specific gravity with K wC . 7) The actual reservoir oil has a K wC + 11.55, where the EOS 7) bubblepoint is close to the uncorrected Glasø bubblepoint prediction. When the correction for paraffinicity is applied, the correction gives a poorer bubblepoint prediction (even though the overall trend in bubblepoints is improved by the Glasø paraffinicity corrections). A quantitatively similar correction to the Glasø correction (but easier to use) is based on the estimate for Whitson’s55,56 Watson characterization factor, K w, and yields ǒ g oǓ
corrected+
ǒ g oǓ measuredǒ K wń11.9 Ǔ 1.1824.
. . . . . . . . . . . (3.83)
The corrected specific gravity correlation is used in the Glasø bubblepoint correlation instead of the measured specific gravity. An estimate of Kw for the stock-tank oil must be available to use this correction. Vazquez and Beggs57 give the following correlations. For g API x 30,
pb
ȱ R ǒ +ȧ27.64ǒg Ǔ10 Ȳ
*11.172 g API
s gc
T)460
Ǔȳ ȧ ȴ
0.9143
,
In summary, significant differences in predicted bubblepoint pressures should not be expected for most reservoir oils with most of the previous correlations. The Lasater and Standing equations are recommended for general use and as a starting point for developing reservoir-specific correlations. Correlations developed for a specific region, such as Glasø’s correlation for the North Sea, should probably be used in that region and, in the case of Glasø’s correlation, may be extended to other regions by use of the paraffinicity correction. 3.4.2 Oil Density. Density of reservoir oil varies from 30 lbm/ft3 for light volatile oils to 60 lbm/ft3 for heavy crudes with little or no solution gas. Oil compressibility may range from 3 10*6 psi*1 for heavy crude oils to 50 10*6 psi*1 for light oils. The variation of oil compressibility with pressure is usually small, although for volatile oils the effect can be significant, particularly for material-balance and reservoir-simulation calculations of highly undersaturated volatile oils. Several methods have been used successfully to correlate oil volumetric properties, including extensions of ideal-solution mixing, EOS’s, corresponding-states correlations, and empirical correlations. Oil density based on black-oil properties is given by òo +
62.4g o ) 0.0136g g R s , . . . . . . . . . . . . . . . . . . . . (3.88) Bo
with ò o in lbm/ft3, B o in bbl/STB, and R s in scf/STB. Correlations can be used to estimate R s and B o from g o, g g, p, and T. Standing-Katz Method. Standing3,17 and Standing and Katz58 give an accurate method for estimating oil densities that uses an extension of ideal-solution mixing. ò o + ò po ) D ò p * D ò T , . . . . . . . . . . . . . . . . . . . . . . (3.89) where ò po is the pseudoliquid density at standard conditions and the terms Dò T and Dò p give corrections for temperature and pressure, respectively. Pseudoliquid density is calculated with ideal-solution mixing and correlations for the apparent liquid densities of ethane
. . . . . . . . . . (3.84)
and, for g API u 30,
pb +
ƪ
ǒ Ǔ ǒ
R 56.06 g s 10 gc
T)460
ƫ
Ǔ
*10.393g API
0.8425
, . . . . . . . . . (3.85)
with p b in psia, T in °F and R s in scf/STB. These equations are based on a large number of data from commercial laboratories. Vazquez and Beggs correct for the effect of separator conditions using a modified gas specific gravity, g gc , which is correlated with first-stageseparator pressure and temperature, and stock-tank-oil gravity.
ƪ
g gc + g g 1 ) ǒ0.5912
10 *4Ǔ g APIT sp log
p ǒ114.7 Ǔƫ, sp
. . . . . . . . . . . . . . . . . . . . (3.86) with T sp in °F and p sp in psia. Standing’s correlation can be used to develop field- or reservoirspecific bubblepoint correlations. A linear relation is usually assumed between bubblepoint pressure and the Standing correlating coefficient. This is a standard approach used in the industry, and the Standing bubblepoint correlating parameter is well suited for developing field-specific correlations. Sometimes the solution gas/oil ratio is needed at a given pressure, and this is readily calculated by solving the bubblepoint correlation for R s . For the Standing correlation,
ƪ(0.055p )10 1.4)10
ƫ
0.0125g API
1.205
. . . . . . . . . (3.87)
System Density at 60°F and 14.7 psia, g/cm3
similar relations can be derived for the other bubblepoint correlations.
Fig. 3.14—Apparent liquid densities of methane and ethane (from Standing33).
Rs + gg
30
0.00091T
;
PHASE BEHAVIOR
g Fig. 3.15—Chart for calculating pseudoliquid density of reservoir oil (from Standing33).
and methane at standard conditions. Given oil composition x i, ò po is calculated from
ȍx M N
i
ò po +
i
i+1
ȍǒx M ńò Ǔ N
i
i
, . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.90)
i
i+1
where Standing and Katz show that apparent liquid densities ò i of C2 and C1 are functions of the densities ò 2) and ò po , respectively (Fig. 3.14). ò C + 15.3 ) 0.3167 ò C 2
2)
ò C + 0.312 ) 0.45 ò po , . . . . . . . . . . . . . . . . . . . . . . . (3.91) 1
C 7)
ȍxM i
where ò C
2)
+
i
i+C 2 C 7)
ȍ ǒx M ńò Ǔ i
i
,
. . . . . . . . . . . . . . . . . . . . (3.92)
i
i+C 2
GAS AND OIL PROPERTIES AND CORRELATIONS
with ò in lbm/ft3. Application of these correlations results in an apparent trial-and-error calculation for ò po . Standing33 presents a graphical correlation (Fig. 3.15) based on these relations, where ò po is found from ò C3) and weight fractions of C2 and C1 (w C2 and w C1, respectively). Figs. 3.16 and 3.17 show the pressure and temperature corrections, D ò p and D ò T , graphically. D ò p is a function of ò po, and D ò T is a function of ( ò po ) D ò p ). Madrazo59 introduced modified curves for D ò p and D ò T that improve predictions at higher pressures and temperatures. Standing3 gives best-fit equations for his original graphical correlations of D ò p and D ò T (Eqs. 3.98 and 3.99), which are not recommended at temperatures u240°F; instead, Madrazo’s graphical correlation can be used. The correction factors can also be used to determine isothermal compressibility and oil FVF at undersaturated conditions. The treatment of nonhydrocarbons in the Standing-Katz method has not received much attention, and the method is not recommended when concentrations of nonhydrocarbons exceed 10 mol%. Standing3 suggests that an apparent liquid density of 29.9 lbm/ft3 can be used for nitrogen but does not address how the nonhydrocarbons should be considered in the calculation procedure (i.e., as part of the C3+ material or following the calculation of ò C and ò C ). 2 1 Madrazo indicates that the volume contribution of nonhydrocar31
Density of System at 60°F and 14.7 psia, lbm/ft3 Fig. 3.16—Pressure correction to the pseudoliquid density at 14.7 psia and 60°F (from Ref. 59).
bons can be neglected completely if the total content is t6 mol%. Vogel and Yarborough60 suggest that the weight fraction of nitrogen should be added to the weight fraction of ethane. Using additive volumes and Eqs. 3.91 and 3.92, we can show that ò C and ò po can be calculated explicitly. Thus, the following is the 2) most direct procedure for calculating ò o from the Standing-Katz method. 1. Calculate the mass of each component. m i + x i M i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.93) 2. Calculate V C C 7)
VC
3)
+
ȍ
i+C 3
3)
.
mi ò i , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.94)
where ò i are component densities at standard conditions (Appendix A). 3. Calculate ò C . 2)
* b ) Ǹb 2 * 4ac , . . . . . . . . . . . . . . . . . . . . (3.95) òC + 2) 2a 32
where a + 0.3167V C , b + m C * 0.3167 m C ) 15.3 V C , 3) 2 2) 3) and c + * 15.3m C . 2) 4. Calculate V C . 2)
VC
2)
+ VC
mC )ò 2 3) C 2
+ VC
3)
)
mC
2
15.3 ) 0.3167ò C
. . . . . . . . . . . . . (3.96) 2)
5. Calculate ò po. ò po +
*b ) Ǹb 2 * 4ac , . . . . . . . . . . . . . . . . . . . . . (3.97) 2a
where a + 0.45V C , b + m C * 0.45m C ) 0.312V C , and 2) 1 1) 2) c + * 0.312m C . 1) 6. Calculate the pressure effect on density. D ò p + 10 *3 ƪ0.167 ) ǒ16.181 * 10 *8 ƪ0.299 ) ǒ263
10 *0.0425òpoǓƫ p 10 *0.0603òpoǓƫ p 2. . . . . . (3.98) PHASE BEHAVIOR
Density of System at Pressure and 60°F, lbm/ft3 Fig. 3.17—Temperature correction to the pseudoliquid density at pressure and 60°F (from Ref. 59).
ò ga + 38.52
7. Calculate the temperature effect on density.
ƪ
D ò T + (T * 60) 0.0133 ) 152.4ǒò po ) D ò pǓ
NJ
* (T * 60) ǒ8.1 2
* ƪ0.0622
*2.45
ƫ
10 Ǔ *6
Nj
10 *0.0764(òpo)D òp)ƫ .
. . . . . . . . . . . (3.99)
8. Calculate mixture density from Eq. 3.89. In the absence of oil composition, Katz41 suggests calculating the pseudoliquid density from stock-tank-oil gravity, g o, solution gas/ oil ratio, R s , and apparent liquid density of the surface gas, ò ga, taken from a graphical correlation (Fig. 3.18), ò po +
62.4g o ) 0.0136 R s g g
1 ) 0.0136ǒR s g gńò gaǓ
. . . . . . . . . . . . . . . . . . . (3.100)
Standing gives an equation for ò ga. GAS AND OIL PROPERTIES AND CORRELATIONS
10 *0.00326 g API
) (94.75 * 33.93 log g API) log g g , . . . . . . . . . . . (3.101) with ò ga in lbm/ft3 and Rs in scf/STB. Alani-Kennedy 61 Method. The Alani-Kennedy method for calculating oil density is a modification of the original van der Waals EOS, with constants a and b given as functions of temperature for normal paraffins C1 to C10 and iso-butane (Table 3.1); two sets of coefficients are reported for methane (for temperatures from 70 to 300°F and from 301 to 460°F) and two sets for ethane (for temperatures from 100 to 249°F and from 250 to 460°F). Lohrenz et al.62 give Alani-Kennedy temperature-dependent coefficients for nonhydrocarbons N2, CO2, and H2S (Table 3.1). The Alani-Kennedy equations are summarized next. Eqs. 3.102b and 3.102c are in the original van der Waals EOS but are not used. p + RT * a2 , . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.102a) v*b v 33
where log a C
+ ǒ3.8405985
10 *3Ǔ M C
* ǒ9.5638281
MC 10 *4Ǔ g 7) ) 261.80818 T C
7)
7)
7)
) ǒ7.3104464
10
*6
Ǔ
M 2C 7)
) 10.753517 . . . . . . . . . . . . . . . . . . . . . (3.103a) and b C
7)
+ ǒ3.499274
10 *2Ǔ M C
) ǒ2.232395
10 *4ǓT * ǒ1.6322572
7)
* 7.2725403 g C
7)
MC 10 *2Ǔ g 7) C 7)
) 6.2256545, . . . . . . . . . . . . . . . . . . . . . . . (3.103b) with ò in lbm/ft3, v in ft3/lbm mol, T in °R, p in psia, and R+universal gas constant+10.73. Solution of the cubic equation for volume is presented in Chap. 4. Density is given by ò+M/v, where M is the mixture molecular weight and v is the molar volume given by the solution to the cubic equation. The Alani-Kennedy method can also be used to estimate oil compressibilities. Rackett,63 Hankinson and Thomson,64 and Hankinson et al.65 give accurate correlations for pure-component saturated-liquid densities, and although these correlations can be extended to mixtures, they have not been tested extensively for reservoir systems. Cullick et al.66 give a modified corresponding-states method for predicting density of reservoir fluids, The method has a better foundation and extrapolating capability than the methods discussed previously (particularly for systems with nonhydrocarbons); however, space does not allow presentation of the method in its entirety. Either the Standing-Katz or Alani-Kennedy method should estimate the densities of most reservoir oils with an accuracy of "2%. The Alani-Kennedy method is suggested for systems at temperatures u250°F and for systems containing appreciable amounts of nonhydrocarbons (u5 mol%). Cubic EOS’s (e.g., Peng-Robinson or Soave-Redlich-Kwong) that use volume translation also estimate liquid densities with an accuracy of a few percent (e.g., the recommended characterization procedures in Chap. 5 or other proposed characterizations 67,68).
Fig. 3.18—Apparent pseudoliquid density of separator gas (from Standing,33 after Katz41).
R 2T 2 a i + 27 p ci , . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.102b) ci 64 RT b i + 1 p ci , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.102c) 8 ci
ȍx a N
a+
i
i
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.102d)
i+1
ȍx b , N
b+
i
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.102e)
i+1
ai +
a 1i ) log a 2i; i 0 C 7) , T
. . . . . . . . . . . . . . . . . . (3.102f)
and b i + b 1iT ) b 2i ; i 0 C 7), . . . . . . . . . . . . . . . . . (3.102g)
TABLE 3.1—CONSTANTS FOR ALANI-KENNEDY61 OIL DENSITY CORRELATION Component
a1
a2
N2
4,300
CO2
8,166
126.0
2.293
H2 S
13,200
0.0
b1
104
b2
4.49
0.3853
0.1818
0.3872
17.9
0.3945
C1 At 70 to 300°F At 300 to 460°F
9,160.6413 147.47333
61.893223 3,247.4533
*3.3162472 *14.072637
0.50874303 1.8326695
C2
34
At 100 to 250°F
46,709.573
At 250 to 460°F
17,495.343
*404.48844 34.163551
5.1520981
0.52239654
2.8201736
0.62309877
C3
20,247.757
190.24420
2.1586448
0.90832519
i-C4
32,204.420
131.63171
3.3862284
1.1013834
n-C4
33,016.212
146.15445
2.902157
1.1168144
i-C5
37,046.234
299.62630
2.1954785
1.4364289
n-C5
37,046.234
299.62630
2.1954785
1.4364289
n-C6
52,093.006
254.56097
3.6961858
1.5929406
n-C7
82,295.457
5.2577968
1.7299902
n-C8
89,185.432
n-C9
124,062.650
n-C10
146,643.830
64.380112 149.39026
5.9897530
1.9310993
37.917238
6.7299934
2.1519973
26.524103
7.8561789
2.3329874 PHASE BEHAVIOR
3.4.3 Undersaturated-Oil Compressibility. With measured data or an appropriate correlation for B o or ò o , Eq. 3.14 readily defines the isothermal compressibility of an oil at pressures greater than the bubblepoint. “Instantaneous” undersaturated-oil compressibility, defined by Eq. 3.15 with the pressure derivative evaluated at a specific pressure, is used in reservoir simulation and well-test interpretation. Another definition of oil compressibility may be used in material-balance calculations (e.g., Craft and Hawkins69)—the “cumulative” or “average” compressibility defines the cumulative volumetric change of oil from the initial reservoir pressure to current reservoir pressure.
Compressibility at Bubblepoint +
pi
V oi c oǒ p Ǔ +
ŕ c ǒ p Ǔ dp o
Bubblepoint Plus 1,000 psia
p
V oi ǒ p i * pǓ
+*
ǒV1 ǓƪV p**Vpǒ pǓƫ. . . . . . . . . . . . . . . . . o
oi
i
oi
(3.104)
Bubblepoint Plus 2,000 psia
The cumulative compressibility is readily identified because it is multiplied by the cumulative reservoir pressure drop, p i * p R. Usually c o is assumed constant; however, this assumption may not be justified for high-pressure volatile oils. Oil compressibility is used to calculate the variation in undersaturated density and FVF with pressure.
Fig. 3.19—Undersaturated-oil-compressibility correlation (from Standing33).
ò o + ò ob expƪc oǒ p * p bǓƫ [ ò ob ƪ1 * c oǒ p b * pǓƫ . . . . . . . . . . . . . . . . . . . . . (3.105a) and B o + B ob expƪc oǒ p b * pǓƫ [ B ob ƪ1 * c oǒ p * p bǓƫ ,
ǒV1 ǓƪV ǒpp*Ǔ *p V o
ob
b
ob
ƫ
. . . . . . . . . . . . . . . . (3.106)
Strictly speaking, the compressibility of an oil mixture is defined only for pressures greater than the bubblepoint pressure. If an oil is at its bubblepoint, the compressibility can be determined and defined only for a positive change in pressure. A reduction in pressure from the bubblepoint results in gas coming out of solution and, subsequently, a change in the mass of the original system for which compressibility is to be determined. Implicit in the definition of compressibility is that the system mass remains constant. Vazquez and Beggs57 propose the following correlation for instantaneous undersaturated-oil compressibility. c o + Ańp, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.107) where A+ 10 *5(5R sb ) 17.2T * 1, 180g gc ) 12.61g API* 1, 433), with c o in psi*1, R sb in scf/STB, T in °F, and p in psia. With this correlation for oil compressibility, undersaturated-oil FVF can be calculated analytically from B o + B ob( p bńp) A.
Constant A determined in this way is a useful correlating parameter, one that helps to identify erroneous undersaturated p- V o data. Standing33 gives a graphical correlation for undersaturated c o (Fig. 3.19) that can be represented by
. . . . . . . . . . . . . . . . . (3.105b)
where consistent units must be used. These equations are derived from the definition of isothermal compressibility assuming that co is constant. When oil compressibility varies significantly with pressure, Eqs. 3.105a and 3.105b are not really valid. The approximations ò o [ ò ob [1 * c o( p b * p)] and B o [ B ob [1 * c o( p * p b)] are used in many applications, and to predict volumetric behavior correctly with these relations requires that co be defined by c o( p) + *
Bubblepoint Oil Density, lbm/ft3
. . . . . . . . . . . . . . . . . . . . . . . . . . . (3.108)
If measured pressure/volume data are available (see Sec. 6.4 in Chap. 6), these data can be used to determine A (e.g., by plotting V ońV ob vs. pńp b on log-log paper). Constant A can then be used to compute compressibilities from the simple relation c o + Ańp. GAS AND OIL PROPERTIES AND CORRELATIONS
c o + 10 *6 exp
ƪ
ƫ
ò ob ) 0.004347 ǒ p * p bǓ * 79.1 , (7.141 10 *4)ǒ p * p bǓ * 12.938 . . . . . . . . . . . . . . . . . . . (3.109)
psi*1,
ò ob in lbm/ft3, and p in psia. with c o in The Alani-Kennedy EOS can also be solved analytically for oil compressibility, and Trube70 gives a corresponding-states method for determining oil compressibility with charts. Any of the correlations mentioned here should yield reasonable estimates of c o. However, we recommend that experimental data be used for volatile oils when c o is greater than about 20 10*6 psi*1. A simple polynomial fit of the relative volume data, V ro + V ońV ob , from a PVT report allows an accurate and explicit equation for undersaturated-oil compressibility. V ro + A 0 ) A 1 p ) A 2 p 2 . . . . . . . . . . . . . . . . . . . . . . . (3.110a)
ǒ Ǔ
ēV ro and c o + * 1 V ro ēp +
T
* ǒ A 1 ) 2A 2 p Ǔ A0 ) A1 p ) A2 p2
, . . . . . . . . . . . . . . . . . . . . (3.110b)
where A0, A1, and A2 are determined from experimental data. Alternatively, measured data can be fit by use of Eq. 3.108. 3.4.4 Bubblepoint-Oil FVF. Oil FVF ranges from 1 bbl/STB for oils containing little solution gas to about 2.5 bbl/STB for volatile oils. B ob increases more or less linearly with the amount of gas in solution, a fact which explains why B ob correlations are similar to bubblepoint pressure correlations. For example, Standing’s3,17,40 correlation for California crude oils is B ob + 0.9759 ) ǒ12 where A + R sǒg gńg oǓ
0.5
10 *5Ǔ A 1.2,
. . . . . . . . . . . . . . . (3.111)
) 1.25T. 35
Glasø’s52 correlation for North Sea crude oils is logǒ B ob * 1 Ǔ + * 6.585 ) 2.9133 log A * 0.2768ǒlog AǓ 2 , . . . . . . . . . . . . . . . . . . . . (3.112) where A + R s ǒg gńg oǓ 0.526) 0.968T. The Vazquez and Beggs57 correlation, based on data from commercial laboratories, is B ob + 1 ) ǒ4.677
10 *4ǓR s ) ǒ0.1751
ǒgg Ǔ * ǒ1.8106 API gc
10 *4Ǔ(T * 60)
ǒ Ǔ
g 10 Ǔ R s(T * 60) gAPI gc *8
4,000 2,000 1,000 800 600 400 200
100°F
100 80 60
120°F 140°F 160°F
40
. . . . . . . . . . . . . . . . . . (3.113a)
20 180°F
for g API x 30 and B ob + 1 ) ǒ4.67 * ǒ0.1337
10 ǓR s ) ǒ0.11 *4
ǒ Ǔ
g 10 Ǔ(T * 60) gAPI gc *4
ǒ Ǔ
g 10 *8ǓR s(T * 60) gAPI . . . . . . . . . (3.113b) gc
10 8 6
200°F 220°F
4 240°F 2 1 0.8 0.6
Sources of Data Beal (1946) Frick (1962)
0.4
for g API u 30, where the effect of separator conditions is included by use of a corrected gas gravity g gc (Eq. 3.86). The Standing and the Vazquez-Beggs correlations indicate that a plot of B o vs. R s should correlate almost linearly. This plot is useful for checking the consistency of reported PVT data from a differential liberation plot. Eq. 3.114,71 which performs considerably better for Middle Eastern oils, also suggests a linear relationship between B ob and R s. B ob+ 1.0 ) ǒ0.177342
10 *3Ǔ R s ) ǒ0.220163
R sǒ g gńg oǓ )ǒ4.292580 ) ǒ0.528707
10 *3Ǔ
10 *6Ǔ R s(T * 60)(1 * g o)
10 *3Ǔ(T * 60). . . . . . . . . . . . . . . . (3.114)
All three B ob correlations (Eqs. 3.113a, 3.113b, and 3.114) should give approximately the same accuracy. Sutton and Farshad’s54 comparative study of gulf coast oils indicates that Standing’s correlation is slightly better for B ob t 1.4 and that Glasø’s correlation is best for B ob u 1.4. 3.4.5 Saturated-Oil Compressibility. Perrine8 introduces a definition for the compressibility of a saturated oil that includes the shrinkage effect of saturated-oil FVF, ēB ońēp, and the expansion effect of gas coming out of solution, B g(ēR sńēp),
ǒ Ǔ
ēB o co + * 1 B o ēp
) T
ǒ Ǔ.
1 B g ēR s 5.615 B o ēp
. . . . . . . . . (3.115)
T
c o is used in the definition of total system compressibility, c t . c t + c f ) c w S w ) c o S o ) c g S g , . . . . . . . . . . . . . . (3.116) where c f +rock compressibility. B g has units ft3/scf. R s is in scf/ STB, and B o in bbl/STB+saturated-oil FVF at the pressure of interest, at or below the original oil’s bubblepoint pressure (where both gas and oil are present). 3.4.6 Oil Viscosity. Typical oil viscosities range from 0.1 cp for near-critical oils to u100 cp for heavy crudes. Temperature, stocktank-oil density, and dissolved gas are the key parameters determining oil viscosity, where viscosity decreases with decreasing stocktank-oil density (increasing oil gravity), increasing temperature, and increasing solution gas. Oil viscosity is one of the most difficult properties to estimate, and most methods offer an accuracy of only about 10 to 20%. Two approaches are used to estimate oil viscosity: empirical and corresponding-states correlations. The empirical methods correlate gas-saturated-oil viscosity in terms of dead-oil (residual or stocktank-oil) viscosity and solution gas/oil ratio. Undersaturated-oil viscosity is related to bubblepoint viscosity and the ratio or differ36
0.2 0.1 0
10
20
30
40
50
60
Fig. 3.20—Beal dead-oil (stock-tank-oil) viscosity correlation including data in Frick (from Standing33).
ence in actual and bubblepoint pressures. Corresponding-states methods use reduced density or reduced pressure and temperature as correlating parameters. 3.4.7 Dead-Oil (Residual- or Stock-Tank-Oil) Viscosity. Several correlations for dead-oil viscosity are given in terms of oil gravity and temperature. Standing,3 for example, gives best-fit equations for the original Beal72 graphical correlation, m oD +
ǒ
7 0.32 ) 1.8 4.5310 g API
Ǔǒ
Ǔ
360 A , . . . . . . . . . (3.117) T ) 200
where A + 10 ƪ0.43)ǒ8.33ńg APIǓƫ . A somewhat modified version of the original correlation is given in Fig. 3.20 by Standing.33 Beggs18 and Beggs and Robinson73 give the following equation for the original Beal correlation, m oD + * 1 ) 10 ƪT
*1.163 expǒ6.9824*0.04658g
Ǔƫ .
API
. . . . . . (3.118)
Bergman* claims that the temperature dependence of the Beggs and Robinson correlation is not valid at lower temperatures (t70°F) and suggests the following correlation, based on viscosity data, for pure compounds and reservoir oils. ln ln( m oD ) 1) + A 0 ) A 1 ln(T ) 310), . . . . . . . . . (3.119) where A 0 + 22.33* 0.194gAPI ) 0.00033 g 2API and A 1 + * 3.20 ) 0.0185 g API . Glasø52 gives a relation (used in the paraffinicity correction of his bubblepoint pressure correlation) for oils with K w + 11.9. m oD + (3.141
10 10)T *3.444(log g API) [10.313(log T )*36.447]. . . . . . . . . . . . . . . . . . . . (3.120)
Al-Khafaji et m oD +
al.74
give the correlation
10 4.9563*0.00488T , ǒ g API ) T ń 30 * 14.29 Ǔ 2.709
. . . . . . . . . . . (3.121)
with T in °F and m oD in cp for Eqs. 3.117 through 3.121. *Personal communication with D.F. Bergman, Amoco Research, Tulsa, Oklahoma (1992).
PHASE BEHAVIOR
Solution gas/oil ratio, scf/STB
Fig. 3.22—Live-oil (saturated) viscosity as a function of dead-oil viscosity and solution gas/oil ratio (from Standing,33 after Beal72 correlation).
Fig. 3.21 shows dead-oil viscosities calculated at 100°F for a range of paraffinicities expressed in terms of K w, together with the Bergman* and Glasø48 correlations. Fig. 3.21—Dead-oil (stock-tank-oil) viscosities at 100°F for varying paraffinicity (from Ref. 33).
3.4.8 Bubblepoint-Oil Viscosity. The original approach by Chew and Connally76 for correlating saturated-oil viscosity in terms of dead-oil viscosity and solution gas/oil ratio is still widely used.
Standing75 gives a relation for dead-oil viscosity in terms of deadoil density, temperature, and the Watson characterization factor.
m ob + A 1 ǒm oDǓ A2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.123)
log( m oD ńò o) +
1 *2.17, A 3ƪK w*ǒ8.24ńg oǓƫ ) 1.639A 2*1.059 . . . . . . . . . . . . . . . . . . . (3.122a)
where A 1 + 1 ) 8.69 log T ) 460, 560 A 2 + 1 ) 0.554 log T ) 460 , 560
. . . . . . . . . . . . . (3.122b)
A 1 + 10.715(R s ) 100) *0.515 . . . . . . . . . . . . . . . . . . (3.124a)
. . . . . . . . . . . . . . . . . (3.122c)
and A 2 + 5.44(R s ) 150) *0.338 . . . . . . . . . . . . . . . . . . (3.124b)
ǒ2.87A 1 * 1Ǔg o A 3 + * 0.1285 , . . . . . . . . . . . . . . . (3.122d) 2.87A 1 * g o and ò o +
Fig. 3.22 shows the variation in m ob with m oD as a function of R s. The functional relations for A1 and A2 reported by various authors differ somewhat, but most are best-fit equations of Chew and Connally’s tabulated results. Beggs and Robinson. 73
go , 1 ) 0.000321(T * 60)10 0.00462gAPI
. . . . . . (3.122e)
with m in cp, T in °F, and ò in g/cm3 for Eqs. 3.117 through 3.122. Eqs. 3.122a through 3.122e represent a best fit of the nomograph for viscosity in terms of temperature, gravity, and characterization factor. Eq. 3.122e (at standard pressure and temperature) is a best fit of thermal expansion data for crude oils. Dead-oil viscosity is one of the most unreliable properties to predict with correlations primarily because of the large effect that oil type (paraffinicity, aromaticity, and asphaltene content) has on viscosity. For example, the oil viscosity of a crude oil with K w + 12 may be 3 to 100 times the viscosity of a less paraffinic crude oil having the same gravity and K w + 11. For this reason the Standing correlation based on the Watson characterization factor is recommended when K w is known. Using an incorrectly estimated K w, however, may lead to a potentially large error in dead-oil viscosity. GAS AND OIL PROPERTIES AND CORRELATIONS
Bergman. * ln A 1 + 4.768 * 0.8359 ln(R s ) 300) . . . . . . . . . . (3.125a) and A 2 + 0.555 )
133.5 . . . . . . . . . . . . . . . . . . (3.125b) R s ) 300
Standing. 3 A 1 + 10 *ǒ7.4 and A 2 +
10 *4ǓR s)ǒ2.2
10 *7ǓR 2s
. . . . . . . . . . . . . . . (3.126a)
0.68 0.25 0.062 ) ) . 10 ǒ8.62 10 *5ǓRs 10 ǒ1.1 10*3ǓRs 10 ǒ3.74 10*3ǓRs . . . . . . . . . . . . . . . . . . (3.126b)
Aziz et
al. 77
A 1 + 0.20 ) ǒ0.80 and A 2 + 0.43 ) ǒ0.57
10 –0.00081 RsǓ . . . . . . . . . . . . . . (3.127a) 10 –0.00072 RsǓ . . . . . . . . . . . (3.127b)
*Personal communication with D.F. Bergman, Amoco Research, Tulsa, Oklahoma (1992).
37
Al-Khafaji et al.74 extend the Chew-Connally76 correlation to higher GOR’s (up to 2,000 scf/STB). A 1 + 0.247)0.2824 A 0) 0.5657 A 20 * 0.4065 A 30 ) 0.0631 A 40 . . . . . . . . . . . . . . . . . . . (3.128a)
ƪǒ m * m oǓc T ) 10 *4ƫ
and A 2 + 0.894 ) 0.0546 A 0 ) 0.07667A 20 * 0.0736 A 30 ) 0.01008 A 40 ,
is therefore desired. Several corresponding-states viscosity correlations can be used for both oil and high-pressure gas mixtures; the Lohrenz et al.62 correlation has become a standard in compositional reservoir simulation. Lohrenz et al. use the Jossi et al.82 correlation for dense-gas mixtures ( ò pru0.1),6
. . . . . . . . . . . . . . (3.128b)
where A 0 + log(R s) and R s + 0.1 yields A 1 + A 2 + 1. R s is given in scf/STB for Eqs. 3.124 through 3.128. Chew and Connally indicate that their correlation is based primarily on data with GOR’s of t1,000 scf/STB and that the scatter in A 1 at higher GOR’s is probably the result of insufficient data. Eqs. 3.128a and 3.128b are based on additional data at higher GOR’s. Eqs. 3.127a and 3.128b appear to be the most well behaved. An interesting observation by Abu-Khamsin and Al-Marhoun78 is that saturated-oil viscosity, m ob, correlates very well with saturated-oil density, ò ob . ln m ob + * 2.652294 ) 8.484462
ò 4ob ,
. . . . . . . . . . (3.129)
This behavior is expected from the Lohrenz et with ò ob in al.62 correlation discussed later. Although Abu-Khamsin and AlMarhoun do not comment on the applicability of Eq. 3.129 to undersaturated oils, it would seem reasonable that their correlation should apply to both saturated and undersaturated oils. In fact, the correlation even appears to predict accurately dead-oil viscosities, m oD, except at low temperatures for heavy crudes. Simon and Graue give graphical correlations for the viscosity of saturated CO2/oil systems (see Chap. 8).79
m o * m ob 0.56 + 0.024m 1.6 ob ) 0.038m ob . 0.001( p * p b) The Vazquez and
Beggs57
m o + m ob ǒ pńp bǓ A ,
. . . . . . . . (3.130)
) 0.0093324ò 4pr , . . . . . . . . . . . . . . . . . . . . . . (3.133a)
ǒ Ǔ
ò ò pr + ò
pc
where A + 2.6 p 1.187 expƪ* 11.513 * ǒ8.98 10 *5Ǔpƫ. A more recent correlation by Abdul-Majeed et al.80 is
ƫ,
. . . . . . . . (3.132a)
where A + 1.9311 * 0.89941 ǒln R sǓ * 0.001194 g 2API ) 0.0092545 g API ǒln R sǓ.
. . . . . . . . . . . . . . . . . . (3.133b)
ò v , . . . . . . . . . . . . . . . . . . . . . . . . (3.133c) M pc
+
ȍ z m ǸM N
i
and m + o
i
i
i+1 N
ȍ z ǸM i
.
. . . . . . . . . . . . . . . . . . . . . . . (3.133d)
i
i+1
Pseudocritical properties T pc, p pc, and v pc are calculated with Kay’s mixing rule. Component viscosities, m i , can be calculated from the Lucas45 low-pressure correlation Eq. 3.67 or from the Stiel and Thodos83 correlation (as suggested by Lohrenz et al.62). m i c Ti + ǒ34
10 *5ǓT ri0.94 . . . . . . . . . . . . . . . . . . . . . . (3.134a)
for Tri x1.5, and m i c Ti + ǒ17.78
10 *5Ǔ(4.58T ri * 1.67) 5ń8 . . . . . . (3.134b)
for T ri u 1.5, where c Ti + 5.35ǒT ci M 3ińp 4ciǓ . Lohrenz et al.62 give a special relation for v c C of the C7+ fraction. 1ń6
7)
+ 21.573 ) 0.015122M C ) 0.070615M C
g , 7) C 7)
7)
* 27.656g C
7)
. . . . . . . . . . . . . . . . (3.135)
with m in cp, c in cp*1, ò in lbm/ft3, v in ft3/lbm mol, T in °R, p in psia, and M in lbm/lbm mol. The Lohrenz et al. method is very sensitive to mixture density and to the critical volumes of heavy components. Adjustment of the critical volumes of heavy (and sometimes light) components to match experimental oil viscosities is usually necessary.
. . . . . . . . . . . . . . . (3.132b)
Eq. 3.132 is based on the observation that a plot of log(m o * m ob) vs. log(p * p b) plots as a straight line with slope of [1.11. Because this observation appears to be fairly general, it can be used to check reported undersaturated-oil viscosities and to develop field-specific correlations. Sutton and Farshad54 and Khan et al.81 present results that indicate that the Standing equation gives good results and that the Vazquez-Beggs correlation tends to overpredict viscosities somewhat. Abdul-Majeed et al.80 indicate that both the Standing and Vazquez-Beggs correlations overpredict viscosities of North African and Middle Eastern oils (253 data), and that their own correlation performed best for these data and for the data used by Vazquez and Beggs. 3.4.10 Compositional Correlation. In compositional reservoir simulation of miscible-gas-injection processes and the depletion of near-critical reservoir fluids, the oil and gas compositions may be very similar. A single viscosity relation consistent for both phases 38
,
7)
. . . . . . . . . . . . . . . . . . . . . . . . . . . (3.131)
logǒ p*p bǓ
1ń6
T pc where c T + 5.35 M 3p 4pc
v cC
correlation is
mo + m ob ) 10 ƪA* 5.2106 ) 1.11
+ 0.10230 ) 0.023364ò pr
) 0.058533ò 2pr * 0.040758ò 3pr
g/cm3.
3.4.9 Undersaturated-Oil Viscosities. Beal72 gives the variation of undersaturated-oil viscosity with pressure graphically where it has been curve fit by Standing.2
1ń4
3.5 IFT and Diffusion Coefficients 3.5.1 IFT. Weinaug and Katz84 propose an extension of the Macleod85 relationship for multicomponent mixtures.
ȍ P ǒx Mò N
s 1ń4 go +
o
i
i+1
i
o
* yi
Ǔ
òg , . . . . . . . . . . . . . . . . . (3.136) Mg
with s in dynes/cm (mN/m) and ò in g/cm3. P i is the parachor of Component i, which can be calculated by group contributions, as shown in Table 3.2. For n-alkanes, the parachors can be expressed by P i + 25.2 ) 2.86M i .
. . . . . . . . . . . . . . . . . . . . . . . . (3.137)
Several authors propose parachors for pure hydrocarbons that deviate from the group-contribution values. For example, P C +77 is 1 often cited for methane instead of the group-contribution value of P C +71. Likewise, P N +41 is often used for nitrogen instead of 2 1 the group-contribution value of P N +35. Fig. 3.23 plots parachors 2 vs. molecular weight for pure components and petroleum fractions. PHASE BEHAVIOR
TABLE 3.2—PARACHORS FOR PURE COMPONENTS AND COMPOUND GROUPS
n-paraffins Heptanes plus of Ref. 4 Gasolines Crude oil
Pure Component C1
71
C2
111
C3
151
C4 (also i-C4)
191
C5 (also i-C5)
231
C6
271
C7
311
C8
351
C9
391
C10
431
N2
35
CO2
49
H2 S
80
Group C
9.0
H
15.5
CH3
55.5
CH2 [in (CH2)n ]
40.0
N
17.5
O
20.0
S
49.1
Example: For methane, CH4. PC1=PC+4(PH)=9+4(15.5)=71.
Fig. 3.23—Hydrocarbon parachors.
Nokay86 gives a simple relation for parachors of pure hydrocarbons (paraffins, olefins, naphthenes, and aromatics) with a normal boiling point between 400 and 1,400°R and specific gravity t1, log P i + * 4.20895 ) 2.29319 log
ǒ Ǔ
T bi , . . . . . (3.138) g 0.5937 i
with T b in °R. Katz and Saltman87 and Katz et al.88 give parachor data for C7+ fractions measured by Standing and Katz,58,89 which are approximately correlated by P i + 35 ) 2.40M i . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.139) The API recommended procedure for estimating petroleum fraction IFT’s is based on an unpublished correlation.27 The graphical correlation can be expressed by 602(1 * T ri) 1.194 , si + K wi
ǒ Ǔ
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.141)
where ò sL ơ ò sv is assumed. The saturated-liquid density can be estimated, for example, with the Rackett63 equation. ò sLi +
P i + 11.4 ) 3.23 M i * 0.0022 M 2i .
M i p ci *ƪ1)ǒ1*TriǓ2ń7ƫ Z , RT ci Ri
. . . . . . . . . . . . . . . . . (3.142)
where Z Ri [ Z ci [ 0.291 * 0.08 w i
. . . . . . . . . . . . . . (3.143)
and R+universal gas constant. The parachors predicted from Eqs. 3.140 through 3.143 are practically constant for a given petroleum fraction (i.e., the temperature effect cancels out). GAS AND OIL PROPERTIES AND CORRELATIONS
. . . . . . . . . . . (3.144)
They also discuss the qualitative effect of asphaltenes on IFT and suggest that the parachor of asphaltic substances generally will not follow the relations of lighter C7+ fractions. Ramey91 gives a method for estimating gas/oil IFT with black-oil PVT properties. We extend the method here to include the effect of solution oil/gas ratio, r s. Considering stock-tank oil and separator gas as the “components” ( o and g) making up reservoir oil and gas, respectively, the Weinaug-Katz84 relation can be written
ƪ ǒMò Ǔ * y ǒMò Ǔƫ ) P ƪx ǒMò Ǔ * y ǒMò Ǔƫ,
s¼ go + P o x o
. . . . . . . . . . . . . . . . . . . . . . . (3.140)
where K w + T 1ń3 ńg, with T b in °R. The parachor can be estimated b with the Macleod relation, Mi P i + s 1ń4 ò sLi , i
Firoozabadi et al.90 give an equation that can be used to approximate the parachor of pure hydrocarbons from C1 through C6 and for C7+ fractions,
g
o
o
o
o
g
o
g
g
o
g
g
. . . . . . . . . . . . . . . . . . . (3.145a) where x o +
1 ) (7.52
1 , . . . . . . . . (3.145b) 10 *6)R sǒM ońg oǓ
x g + 1 * x o , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.145c) yo +
1 ) (7.52
1 , 10 *6)ǒ M ońg o Ǔr s
. . . . . . . . . . . (3.145d)
y g + 1 * y o , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.145e) òo +
62.4g o ) 0.0136g g R s , 62.4 B o
. . . . . . . . . . . . . . . . . . (3.145f)
ò g + 0.0932ǒ pM gńZT Ǔ , . . . . . . . . . . . . . . . . . . . . . . (3.145g) M o + x o M o ) x g M g , . . . . . . . . . . . . . . . . . . . . . . . . (3.145h) 39
M g + y o M o ) y g M g ,ĂĂ . . . . . . . . . . . . . . . . . . . . . . . . (3.145i)
)
M o + 6, 084ńg API * 5.9 , . . . . . . . . . . . . . . . . . . . . . (3.145j) M g + 28.97g g ,
. . . . . . . . . . . . . . . . . . (3.149b)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.145k)
P o + ǒ2.376 ) 0.0102g APIǓńM o ,
. . . . . . . . . . . . . . . (3.145l)
1.03587 1.76474 ) , expǒ1.52996T ijǓ expǒ3.89411T ijǓ
T ij +
T , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.149c) (åńk) ij
and P g + 25.2 ) 2.86M g , . . . . . . . . . . . . . . . . . . . . . (3.145m)
ǒ åńk Ǔ ij+ ƪǒ åńk Ǔ i ǒåńkǓ jƫ 1ń2 , . . . . . . . . . . . . . . . . . . . . (3.149d)
with ò in g/cm3, R s in scf/STB, B o in bbl/STB, T in °R, and p in psia and where x o and x g+mole fractions of the surface-oil and -gas components, respectively, in the oil phase, and y o and y g+mole fractions of the surface-oil and -gas components, respectively, in the gas phase. In the traditional black-oil approach r s + 0, simplifying the relations to those originally suggested by Ramey.91 Eq. 3.145 is useful in black-oil reservoir simulation and when compositional data are not available. The black-oil approach generally is not recommended for predicting gas/oil IFT’s unless the surface-oil parachor has been fit to experimental IFT data (or to IFT’s calculated with compositions and densities from an EOS characterization by use of Eq. 3.136).
ǒ åńk Ǔ i + 65.3T ci Z 18ń5 ,
3.5.2 Diffusion Coefficients. Molecular diffusion in multicomponent mixtures is a complex problem. The standard engineering approach uses an effective diffusion coefficient for Component i in a mixture, D im, where D im can be calculated in one of two ways: (1) from binary diffusion coefficients and mixture composition or (2) from Component i properties and mixture viscosity. The first approach uses the Wilke92 formula to calculate D im. D im +
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.146)
N
j
ij
j+1 j0i
where y i +mixture mole fraction and D ij + D ji is the binary diffusivity at the pressure and temperature of the mixture. Sigmund93 correlates the effect of pressure and temperature on diffusion coefficients using a corresponding-states approach with reduced density. ò M D ij + 0.99589 ) 0.096016ò pr * 0.22035ò 2pr ò oM D oij ) 0.032874ò 3pr , . . . . . . . . . . . . . . . . . . . . . . . (3.147) where D ij +diffusion coefficient at pressure and temperature, ò pr+pseudoreduced density+ ò Mńò Mpc + ǒ òńM Ǔv pc , ò M +mixture molar density, ò oM D oij +low-pressure density-diffusivity product, and v pc +pseudocritical molar volume calculated with Kay’s5 mixing rule. Note that the ratio ò M D ijńò oD oij is the same for all binary pairs in a mixture because ò pr is a function of only mixture density and composition. da Silva and Belery12 note that the Sigmund correlation does not work well for liquid systems and propose the following extrapolation for ò pru3. ò MD ij + 0.18839 exp(3 * ò pr) , . . . . . . . . . . . . . . . . (3.148) ò oM D oij which avoids negative D ij for oils at ò pru3.7 as estimated by the Sigmund correlation. Low-pressure binary gas diffusion coefficients,6 D oij , can be estimated from D oij + 0.001883
T 3ń2ƪǒ1ńM iǓ ) ǒ1ńM jǓƫ p os 2ijW ij
0.193 ) where W ij + 1.06036 T ij0.1561 expǒ0.47635T ijǓ 40
. . . . . . . . . . . . . . . . . . . . . . . . (3.149e)
s ij + 0.5ǒs i ) s jǓ , . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.149f) and s i + 0.1866
v 1ń3 ci Z 6ń5 ci
,
. . . . . . . . . . . . . . . . . . . . . . . . (3.149g)
with the diffusion coefficient, D oij , in cm2/s; molecular weight, M, in kg/kmol; temperature, T, in K, pressure; p, in bar; Lennard Jones 12-6 potential parameter, s, in Å; Lennard-Jones 12-6 potential parameter, e/k, in K; and critical volume, vc , in m3/kmol and where Z c +critical compressibility factor and i and j+diffusing and concentrated species, respectively. To obtain the low-pressure density-diffusivity product, we use the ideal-gas law, ò oM + p ońRT, to get D oij ò oM
+ ǒ2.2648
10
*5
Ǔ
T 1ń2ƪǒ1ńM iǓ ) ǒ1ńM jǓƫ
1ń2
s 2ij W ij
,
. . . . . . . . . . . . . . . . . . (3.150)
1 * yi
ȍ y ńD
ci
0.5
, . . . . . . . . (3.149a)
where ò and ò M have units g mol/cm3. The accuracy of the Sigmund correlation for liquids is not known, but the extension proposed by da Silva and Belery (Eq. 148) for large reduced densities does avoid negative diffusivities calculated by the Sigmund equation.94 Renner95 proposes a generalized correlation for effective diffusion coefficients of light hydrocarbons and CO2 in reservoir liquids that can be used as an alternative to the Sigmund-type correlation. *1.831 4.524 M *0.6898 ò 1.706 T , D im + 10 *9 m *0.4562 o Mi p i
. . . . . . . . . . . . . . . . . . . (3.151) with D in cm2/s and where m o +oil viscosity in cp, M i +molecular weight, ò Mi +molar density of Component i at p and T in g mol/cm3, p+pressure in psia, and T+temperature in K. This correlation is based on 141 experimental data with the following property ranges: 0.2t m ot134 cp; 16tM it44; 0.04t ò Mit7 kmol/m3; 14.7tp t2,560 psia; and 273tTt333 K, where i+CO2, C1, C2, and C3. Renner also gives a correlation for diffusivity of CO2 in water/ brine systems. D CO
2*w
+ ǒ6.392
6.911 10 3Ǔ m CO m w*0.1584, . . . . . . . . . (3.152) 2
with D in cm2/s and m in cp. 3.6 KĆValue Correlations This section covers the estimation of equilibrium K values by correlations and the calculation of two-phase equilibrium when K values are known. The K value is defined as the ratio of equilibrium gas composition yi to the equilibrium liquid composition x i, K i 5 y ińx i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.153) K i is a function of pressure, temperature, and overall composition. K values can be estimated with empirical correlations or by satisfying the equal-fugacity constraint with an EOS (see Chap. 4). Although the increasing use of EOS’s has tended to lessen interest in empirical K-value correlations, empirical methods are still useful for such engineering calculations as (1) multistage surface separation, (2) compositional reservoir material balance, and (3) checking the consistency of separator-oil and gas compositions. PHASE BEHAVIOR
Fig. 3.24—General behavior of a K value vs. pressure plot on log-log scale.
Several methods for correlating K values have appeared in the past 50 years. Most rely on two limiting conditions for describing the pressure dependence of K values. First, at low pressures, Raoult’s and Dalton’s laws3 can be used to show that K i [ p vi ǒ T Ǔńp, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (3.154) where p v +component vapor pressure at the system temperature. The limitations of this equation are that temperature must be less than the component critical temperature (because vapor pressure is not defined at supercritical temperatures) and that the component behaves as an ideal gas. Also, the equation implies that the K value is independent of overall composition. In fact, the pressure dependence of lowpressure K values is closely approximated by Eq. 3.154. The second observation is that, at high pressures, the K values of all components in a mixture tend to converge to unity at the same pressure. This pressure is called the convergence pressure96 and, for binaries, represents the actual mixture critical pressure. For multicomponent mixtures, the convergence pressure is a nonphysical condition unless the system temperature equals the mixture critical temperature.97,98 This is because a mixture becomes single phase at the bubblepoint or dewpoint pressure before reaching the convergence pressure. The log-log plot of K i vs. pressure in Fig. 3.24 shows how the ideal-gas and convergence-pressure conditions define the K-value behavior at limiting conditions. For light components (where T u T ci ), K values decrease monotonically toward the convergence pressure. For heavier components (where T t T ci ), K values initially decrease as a function of pressure at low pressures, passing through unity when system pressure equals the vapor pressure of a particular component, reaching a minimum, and finally increasing toward unity at the convergence pressure. GAS AND OIL PROPERTIES AND CORRELATIONS
For reservoir fluids, the pressure where K values reach a minimum is usually u1,000 psia (Fig. 3.25), implying that K values are more or less independent of convergence pressure (i.e., composition) at pressures t1,000 psia. This observation has been used to develop general “low-pressure” K-value correlations for surfaceseparator calculations. 3.6.1 Hoffman et al. Method. Hoffman et al.99 propose a method for correlating K values that has received widespread application. Ki +
10
ǒA0 ) A1 Fi Ǔ p
or log K i p + A 0 ) A 1 F i , . . . . . . . . . . . . . . . . . . . . . . (3.155) where F i +
1ńT bi * 1ńT logǒ p cińp scǓ ; . . . . . . . . . . . . (3.156) 1ńT bi * 1ńT ci
T c +critical temperature; p c +pressure; T b +normal boiling point; p sc +pressure at standard conditions; and A 1 and A 0 +slope and intercept, respectively, of the plot log(K i p) vs. F i. Hoffman et al. show that measured K values for a reservoir gas condensate correlate well with the proposed equation. They found that trend of log(K i p) vs. F i is linear for components C1 through C6 at all pressures, while the function turns downward for heavier components at low pressures. Interestingly, the trend becomes more linear for all components at higher pressures. As Fig. 3.26 shows, Slope A 1 and Intercept A 0 vary with pressure. For low pressures, K i [ p vńp. With the Clapeyron vapor pressure relation,5 log(p v) + a * bńT results in A 0 + log(p sc) and A 1 + 1. These limiting values of A 0 and A 1 are close to the values found when A 0( p) and A 1( p) are extrapolated to p + p sc. Because 41
Fig. 3.25—K values at 120°F for binary- and reservoir-fluid systems with convergence pressures ranging from 800 to 10,000 psia (from Standing3).
K values tend toward unity as pressure approaches the convergence pressure, p K , it is necessary that A 0 + log(p K) and A 1 ³ 0. Several authors have noted that plots of log(K i p) vs. F i tend to converge at a common point. Brinkman and Sicking101 suggest that this “pivot” point represents the convergence pressure where K i + 1 and p + p K. The value of F i at the pivot point, F K, is easily shown to equal log(p Kńp sc). It is interesting to note that the well-known Wilson102,103 equation, Ki +
Ǔ exp 5.37(1 ) w i)ǒ1 * T *1 ri , . . . . . . . . . . . . . . (3.157) p ri
is identical to the Hoffman et al.99 relation for A 0 + log(p sc) and A 1 + 1 when the Edmister104 correlation for acentric factor equation, 42
T bińT ci wi + 3 logǒ p cińp scǓ * 1 , . . . . . . . . . . . . (3.158) 7 1 * T bińT ci is used in the Wilson equation. Note that 5.37+(7/3) ln (10). Whitson and Torp100 suggest a generalized form of the Hoffman et al.99 equation in terms of convergence pressure and acentric factor.
ǒ Ǔ
p K i + pci K
A 1*1
Ǔƫ expƪ5.37 A 1 (1 ) w i)ǒ1 * T *1 ri , p ri . . . . . . . . . . . . . . . . . . . (3.159)
where A 1 +a function of pressure, with A 1 + 1 at p + p sc and A 1 + 0 at p + p K. The key characteristics of K values vs. pressure PHASE BEHAVIOR
log pK
TABLE 3.3—VALUES OF b AND Tb FOR USE IN STANDING LOW-PRESSURE K-VALUE CORRELATION
–
Component, i
bi (cycle-°R)
Tbi °R
470
109
N2
Intercept A0
Slope A1
Pressure, psia
Fig. 3.26—Pressure dependence of slope, A1, and intercept, A0, in Hoffman et al. Kp-F relationship (Eq. 3.155) for a North Sea gas condesate NS-1 (from Whitson and Torp100).
CO2
652
194
H2 S
1,136
331
C1
300
94
C2
1,145
303
C3
1,799
416
i-C4
2,037
471
n-C4
2,153
491
i-C5
2,368
542
n-C5
2,480
557
C6 (lumped)
2,738
610
n-C6
2,780
616
n-C7
3,068
669
n-C8
3,335
718
n-C9
3,590
763
n-C10
3,828
805
For C7+ fractions, see Eqs. 3.161f through 3.161h
and temperature are correctly predicted by Eq. 3.159, where the following pressure dependence for A 1 is suggested. A 1 + 1 * (pńp K) A 2 , . . . . . . . . . . . . . . . . . . . . . . . . . . (3.160) where A 2 ranges from 0.5 to 0.8 and pressures p and p K are given in psig. Canfield105 also suggests a simple K-value correlation based on convergence pressure. 3.6.2 Standing Low-Pressure K Values. Standing106 uses the Hoffman et al.99 method to generate a low-pressure K-value equation for surface-separator calculations ( p sp t 1, 000 psia and T sp t 200°F). Standing fits A 1 and A 0 in Eq. 3.155 as a function of pressure using K-value data from an Oklahoma City crude oil. He treats the C 7) by correlating the behavior of K C as a function of 7) “effective” carbon number n C . The Standing equations are 7)
ǒA0 ) A1 Fi Ǔ
, . . . . . . . . . . . . . . . . . . . . . . . . (3.161a)
F i + b iǒ1ńT bi * 1ńTǓ,
. . . . . . . . . . . . . . . . . . . . . . . (3.161b)
K i + p1 10 sp
b i + logǒ p cińp scǓńǒ1ńT bi * 1ńT ciǓ , . . . . . . . . . . . . . . . (3.161c) A 0ǒ pǓ + 1.2 ) ǒ4.5
10
*4
Ǔp ) ǒ15
10
*8
Ǔp ,
10 *4Ǔp * ǒ3.5
10 *8Ǔp 2,
. . . . . . . . . . . . . . . . . . . (3.161e) nC
7)
+ 7.3 ) 0.0075T ) 0.0016p,
bC
7)
+ 1, 013 ) 324n C
and T bC
7)
7)
+ 301 ) 59.85n C
. . . . . . . . . . . . . (3.161f)
* 4.256n 2C 7)
7)
,
* 0.971n 2C
. . . . . . . (3.161g) ,
7)
. . . . . (3.161h)
with T in °R except when calculating n C (for n C , T is in °F) and 7) 7) p in psia. Standing suggests modified values of b i and T bi for nonhydrocarbons, methane, and ethane (Table 3.3). Glasø and Whitson107 show that these equations are accurate for separator flash calculations of crude oils with GOR’s ranging from 300 to 1,500 scf/STB and oil gravity ranging from 26 to 48°API. Experience shows, however, that significant errors in calculated GOR may result for lean gas condensates, probably because of inaccurate C 1 and GAS AND OIL PROPERTIES AND CORRELATIONS
3.6.3 Galimberti-Campbell Method. Galimberti and Campbell108,109 suggested another useful approach for correlating K values where log K i + A 0 ) A 1T ci2
. . . . . . . . . . . . . . . . . . . . . . . . . (3.162)
is shown to correlate K values for several simple mixtures containing hydrocarbons C 1 through C 10 at pressures up to 3,000 psia and temperatures from *60 to 300°F. Whitson developed a low-pressure K-value correlation, based on data from Roland,110 at pressures t1,000 psia and temperatures from 40 to 200°F, for separator calculations of gas condensates. A 0 + 4.276 * ǒ7.6
10 *4ǓT
) ƪ* 1.18 ) ǒ5.675
10 *4ǓTƫ log p , . . . . . . . . (3.163a)
NJ
A 1 + 10 *6 ǒ* 4.9563 ) 0.00955T Ǔ ) ƪǒ1.9094
2
. . . . . . . . . . . . . . . . . . (3.161d) A 1ǒ pǓ + 0.890 * ǒ1.7
C 7) K values. The Hoffman et al. method with Standing’s low-pressure correlations are particularly useful for checking the consistency of separator-gas and -oil compositions.
* ǒ1.235
10 *5ǓT ) ǒ3.34
10 *3Ǔ
Nj
10 *8ǓT 2ƫ p , . . . (3.163b)
T cC1 + 343 * 0.04p, . . . . . . . . . . . . . . . . . . . . . . . . . (3.163c) and T c C7) + 1, 052.5 * 0.5125T ) 0.00375T 2 , . . . . (3.163d) with p in psia, T in °F, and T c in °R. 3.6.4 Nonhydrocarbon K Values. Lohrenz et al.111 reported nonhydrocarbon K values as a function of pressure, temperature, and convergence pressure. ln K H
2S
ǒ
p + 1*p
K
Ǔ ƪ6.3992127 ) 1, 399.2204 T 0.8
* 0.76885112 ln p * *
ƫ
1, 112, 446.2 , T2
18.215052 ln p T
. . . . . . . . . . . . . . . . . . . . . (3.164a) 43
p 1, 184.2409 + ǒ1 * p Ǔ ǒ11.294748 * T 0.4
ln K N
2
K
Ǔ
* 0.90459907 ln p , . . . . . . . . . . . . . . . . . . . (3.164b)
ǒ
p ln K CO + 1 * p 2
0.6
K
ln p )
Ǔ ǒ7.0201913 * 152.7291 * 1.8896974 T
Ǔ
1, 719.2956 ln p 644, 740.69 ln p * , T T2 . . . . . . . . . . . . . . . . . . . (3.164c)
with p in psia and T in °R. For low-pressure K-value estimation, the first term in Eq. 3.164 simplifies to unity (assuming that 1 * pńp K [ 1) and the K values become functions of pressure and temperature only. However, these equations do not give the correct low-pressure value of ē(ln K i)ńē(ln p) + * 1 3.6.5 Convergence-Pressure Estimation. For correlation purposes, convergence pressure is used as a variable to define the composition dependence of K values. Convergence pressure is a function of overall composition and temperature. Whitson and Michelsen112 show that convergence pressure is a thermodynamic phenomenon, with the characteristics of a true mixture critical point, that can be predicted with EOS’s. Rzasa et al.113 give an empirical correlation for convergence pressure as a function of temperature and the product (Mg) C . 7) Standing2 suggests that convergence pressure of reservoir fluids varies almost linearly with C 7) molecular weight. Convergence pressure can also be calculated with a trial-and-error procedure suggested by Rowe.97,98,114 This procedure involves the use of several empirical correlations for estimating mixture critical pressure and temperature, pseudocomponent critical properties, and the K values of methane and octane. The Galimberti and Campbell108,109 K-value method is used to estimate K values of other components by interpolation and extrapolation of the C 1 and C 8 K values. This approach to convergence pressure is necessary if the K values are used for processes that approach critical conditions or where K values change significantly because of overall composition effects. The method cannot, of course, be more accurate than the correlations it uses and therefore is expected to yield only qualitatively correct results. For reservoir calculations where convergence pressure can be assumed constant (e.g., pressure depletion), a more direct approach to determining convergence pressure is suggested. With a K-value correlation of the form K i + K( p K, p, T ) as in Eq. 3.159, the convergence pressure can be estimated from a single experimental saturation pressure. For a bubblepoint and a dewpoint, Eqs. 3.165 and 3.166, respectively, must be satisfied. F ǒ p KǓ + 1 *
ȍ z K ǒp , p , TǓ + 0 N
i
i
K
b
. . . . . . . . . . . . . (3.165)
i+1
and Fǒ p KǓ + 1 *
ȍ N
zi
i+1 K i ǒ p K, p d , T Ǔ
+ 0, . . . . . . . . . . . (3.166)
where z i, p b, or p d and T are specified and p K is determined. The two-phase flash calculation, with K values given, is discussed in Chap. 4 in the Phase-Split Calculation section. References 1. The SI Metric System of Units and SPE Metric Standard, SPE, Richardson, Texas (June 1982). 2. van der Waals, J.D.: “Continuity of the Gaseous and Liquid State of Matter,” PhD dissertation, U. of Leiden (1873). 3. Standing, M.B.: Volumetric and Phase Behavior of Oil Field Hydrocarbon Systems, SPE, Richardson, Texas (1981). 4. Standing, M.B. and Katz, D.L.: “Density of Natural Gases,” Trans., AIME (1942) 146, 140. 44
5. Kay, W.B.: “Density of Hydrocarbon Gases and Vapors at High Temperature and Pressure,” Ind. Eng. Chem. (1936) No. 28, 1014. 6. Reid, R.C., Prausnitz, J.M., and Polling, B.E.: The Properties of Gases and Liquids, fourth edition, McGraw-Hill Book Co. Inc., New York City (1987) 388–485. 7. Sutton, R.P.: “Compressibility Factors for High-Molecular Weight Reservoir Gases,” paper SPE 14265 presented at the 1985 SPE Annual Technical Conference and Exhibition, Las Vegas, Nevada, 22–25 September. 8. Ramey, H.J. Jr.: “Rapid Methods for Estimating Reservoir Compressibilities,” JPT (April 1964) 447; Trans., AIME, 231. 9. Fetkovich, M.J., Reese, D.E., and Whitson, C.H.: “Application of a General Material Balance for High-Pressure Gas Reservoirs,” SPE Journal (March 1998) 3. 10. Fick, A.: Am. Phys., Leipzig (1855) 170, 59. 11. Coats, K.H.: “Implicit Compositional Simulation of Single-Porosity and Dual-Porosity Reservoirs,” paper SPE 18427 presented at the 1989 SPE Symposium on Reservoir Simulation, Houston, 6–8 February. 12. da Silva, F.V. and Belery, P.: “Molecular Diffusion in Naturally Fractured Reservoirs—A Decisive Recovery Mechanism,” paper SPE 19672 presented at the 1987 SPE Annual Technical Conference and Exhibition, San Antonio, Texas, 8–11 October. 13. Amyx, J.W., Bass, D.M. Jr., and Whiting, R.L.: Petroleum Reservoir Engineering, McGraw-Hill Book Co. Inc., New York City (1960). 14. Christoffersen, K. and Whitson, C.H.: “Gas/Oil Capillary Pressure of Chalk at Elevated Pressures,” SPEFE (September 1995) 153. 15. Delclaud, J., Rochon, J., and Nectoux, A.: “Investigation of Gas/Oil Relative Permeabilities: High-Permeability Oil Reservoir Application,” paper SPE 16966 presented at the 1987 SPE Annual Technical Conference and Exhibition, Dallas, 27–30 September. 16. Katz, D.L. et al.: Handbook of Natural Gas Engineering, McGraw-Hill Book Co. Inc., New York City (1959) 69–93. 17. Standing, M.B.: Oil-System Correlations, P.P. Handbook (ed.), McGraw-Hill Book Co. Inc., New York City (1962). 18. Beggs, H.D.: “Oil System Correlations,” Petroleum Engineering Handbook, SPE, Richardson, TX (1987) Chap. 22. 19. McCain, W.D. Jr.: “Reservoir-Fluid Property Correlations—State of the Art,” SPERE (May 1991) 266. 20. Whitson, C.H. and Torp, S.B.: “Evaluating Constant Volume Depletion Data,” JPT (March 1983) 610; Trans., AIME, 275. 21. Hall, K.R. and Yarborough, L.: “A New EOS for Z-factor Calculations,” Oil & Gas J. (18 June 1973) 82. 22. Yarborough, L. and Hall, K.R.: “How to Solve EOS for Z-factors,” Oil & Gas J. (18 February 1974) 86. 23. Takacs, G.: “Comparisons Made for Computer Z-factor Calculations,” Oil & Gas J. (20 December 1976) 64. 24. Dranchuk, P.M. and Abou-Kassem, J.H.: “Calculation of Z-Factors for Natural Gases Using Equations of State,” J. Cdn. Pet. Tech. (July–September 1975) 14, No. 3, 34. 25. Brill, J.P. and Beggs, H.D.: “Two-Phase Flow in Pipes,” paper presented at the U. Tulsa INTERCOMP Course, The Hague (1974). 26. Lee, B.I. and Kesler, M.G.: “A Generalized Thermodynamic Correlation Based on Three-Parameter Corresponding States,” AIChE J. (1975) 21, 510. 27. API Technical Data Book––Petroleum Refining, third edition, API, New York City (1977). 28. Starling, K.E., Mannan, M., and Savidge, J.L.: “Equation Predicts Supercompressibility for Wet, Sour Gases,” Oil & Gas J. (2 January 1989) 31. 29. Ely, J.F. and Hanley, H.J.M.: Ind. Eng. Chem. Fund. (1983) 22, 90. 30. Wichert, E. and Aziz, K.: “Compressibility Factor of Sour Natural Gases,” Cdn. J. Chem. Eng. (1971) 49, 267. 31. Wichert, E. and Aziz, K.: “Calculate Z’s for Sour Gases,” Hydro. Proc. (May 1972) 51, 119. 32. Matthews, T.A., Roland, C.H., and Katz, D.L.: “High Pressure Gas Measurement,” Petroleum Refiner (1942) 21, No. 6, 58. 33. Standing, M.B.: Petroleum Engineering Data Book, Norwegian Inst. of Technology, Trondheim, Norway (1974). 34. Eilerts, C.K.: “Gas Condensate Reservoir Engineering, 1. The Reserve Fluid, Its Composition and Phase Behavior,” Oil & Gas J. (1 February 1947). 35. Cragoe, C.S.: “Thermodynamic Properties of Petroleum Products,” U.S. Dept. of Commerce, Washington, DC (1929) 97. 36. Gold, D.K., McCain, W.D. Jr., and Jennings, J.W.: “An Improved Method for the Determination of the Reservoir Gas Gravity for Retrograde Gases,” paper SPE 17310 presented at the 1988 SPE Permian Basin Oil and Gas Recovery Conference, Midland, Texas, 10–11 March. PHASE BEHAVIOR
37. Gold, D.K., McCain, W.D. Jr., and Jennings, J.W.: “An Improved Method for the Determination of the Reservoir Gas Gravity for Retrograde Gases,” JPT (July 1989) 41, 747; Trans., AIME, 287. 38. Whitson, C.H.: “Discussion of An Improved Method for the Determination of the Reservoir-Gas Specific-Gravity for Retrograde Gases,” JPT (November 1989) 1216. 39. Leshikar, A.G.: “How to Estimate Equivalent Gas Volume of Stock Tank Condensate,” World Oil (January 1961) 108. 40. Standing, M.B.: “A Pressure-Volume-Temperature Correlation for Mixtures of California Oils and Gases,” Drill. & Prod. Prac. (1947) 275. 41. Katz, D.L.: “Prediction of the Shrinkage of Crude Oils,” Drill. & Prod. Prac. (1942) 137. 42. Carr, N.L., Kobayashi, R., and Burrows, D.B.: “Viscosity of Hydrocarbon Gases Under Pressure,” Trans., AIME (1954) 201, 264. 43. Dempsey, J.R.: “Computer Routine Treats Gas Viscosity as a Variable,” Oil & Gas J. (16 August 1965) 141. 44. Lee, A.L., Gonzalez, M.H., and Eakin, B.E.: “The Viscosity of Natural Gases,” JPT (August 1966) 997; Trans., AIME, 237. 45. Lucas, K.: Chem. Ing. Tech. (1981) 53, 959. 46. Sage, B.H. and Olds, R.H.: “Volumetric Behavior of Oil and Gas from Several San Joaquin Valley Fields,” Trans., AIME (1947) 170, 156. 47. Eilerts, C.K.: Phase Relations of Gas Condensate Fluids, Monograph 10, U.S. Bureau of Mines, American Gas Assn., New York City (1957) 1 and 2. 48. Eilerts, C.K. et al.: “Phase Relations of a Gas-Condensate Fluid at Low Tempertures, Including the Critical State,” Pet. Eng. (February 1948) 19, 154. 49. Nemeth, L.K. and Kennedy, H.T.: “A Correlation of Dewpoint Pressure With Fluid Composition and Temperature,” SPEJ (June 1967) 99; Trans., AIME, 240. 50. Organick, E.I. and Golding, B.H.: “Prediction of Saturation Pressures for Condensate-Gas and Volatile-Oil Mixtures,” Trans., AIME (1952) 195, 135. 51. Kurata, F. and Katz, D.L.: “Critical Properties of Volatile Hydrocarbon Mixtures,” Trans., AIChE (1942) 38, 995. 52. Glasø, O.: “Generalized Pressure/Volume/Temperature Correlations,” JPT (November 1980) 785. 53. Lasater, J.A.: “Bubblepoint Pressure Correlation,” Trans., AIME (1958) 213, 379. 54. Sutton, R.P. and Farshad, F.F.: “Evaluation of Empirically Derived PVT Properties for Gulf of Mexico Crude Oils,” SPERE (February 1990) 79. 55. Whitson, C.H.: “Characterizing Hydrocarbon Plus Fractions,” paper SPE 12233 presented at the 1980 SPE European Offshore Petroleum Conference, London, 21–24 October. 56. Whitson, C.H.: “Characterizing Hydrocarbon Plus Fractions,” SPEJ (August 1983) 683; Trans., AIME, 275. 57. Vazquez, M. and Beggs, H.D.: “Correlations for Fluid Physical Property Prediction,” JPT (June 1980) 968. 58. Standing, M.B. and Katz, D.L.: “Density of Crude Oils Saturated With Natural Gas,” Trans., AIME (1942) 146, 159. 59. Madrazo, A.: “Liquid-Density Correlation of Hydrocarbon Systems,” Trans., AIME (1960) 219, 386. 60. Vogel, J.L. and Yarborough, L.: “The Effect of Nitrogen on the Phase Behavior and Physical Properties of Reservoir Fluids,” paper SPE 8815 presented at the 1980 SPE Annual Technical Conference and Exhibition, Tulsa, Oklahoma, 20–23 April. 61. Alani, G.H. and Kennedy, H.T.: “Volumes of Liquid Hydrocarbons at High Temperatures and Pressures,” Trans., AIME (1960) 219, 288. 62. Lohrenz, J., Bray, B.G., and Clark, C.R.: “Calculating Viscosities of Reservoir Fluids From Their Compositions,” JPT (October 1964) 1171; Trans., AIME, 231. 63. Rackett, H.G.: “EOS for Saturated Liquids,” J. Chem. Eng. Data (1970) 15, No. 4, 514. 64. Hankinson, R.W. and Thomson, G.H.: “A New Correlation for Saturated Densities of Liquids and Their Mixtures,” AIChE J. (1979) 25, No. 4, 653. 65. Hankinson, R.W. et al.: “Volume Correction Factors for Lubricating Oils,” Oil & Gas J. (28 September 1981) 297. 66. Cullick, A.S., Pebdani, F.N., and Griewank, A.K.: “Modified Corresponding States Method for Predicting Densities of Petroleum Reservoir Fluids,” paper presented at the 1988 AIChE Spring Natl. Meeting, New Orleans, 7–10 March. 67. Chien, M.C.H. and Monroy, M.R.: “Two New Density Correlations,” paper SPE 15676 presented at the 1976 SPE Annual Technical Conference and Exhibition, New Orleans, 5–8 October. 68. Ahmed, T.: Hydrocarbon Phase Behavior, first edition, Gulf Publishing Co., Houston (1989) 7. GAS AND OIL PROPERTIES AND CORRELATIONS
69. Craft, B.C. and Hawkins, M.: Applied Petroleum Reservoir Engineering, first edition, Prentice-Hall, Englewood Cliffs, New Jersey (1959) 126–29. 70. Trube, A.S.: “Compressibility of Undersaturated Hydrocarbon Reservoir Fluids,” Trans., AIME (1957) 210, 241. 71. Al-Marhoun, M.A.: “New Correlations for FVFs of Oil and Gas Mixtures,” PhD dissertation, King Fahd U. of Petroleum & Minerals (1990). 72. Beal, C.: “The Viscosity of Air, Water, Natural Gas, Crude Oil and Its Associated Gases at Oilfield Temperatures and Pressures,” Trans., AIME (1946) 165, 94. 73. Beggs, H.D. and Robinson, J.R.: “Estimating the Viscosity of Crude Oil Systems,” JPT (September 1975) 1140. 74. Al-Khafaji, A.H., Abdul-Majeed, G.H., and Hassoon, S.F.: “Viscosity Correlation for Dead, Live, and Undersaturated Crude Oils,” J. Pet. Res. (1987) 6, No. 2, 1. 75. Standing, M.B.: “UOP Characterization Factor,” TI program listing, available from C.H. Whitson, Norwegian Inst. of Science and Technology, NTNU,
[email protected]. 76. Chew, J.N. and Connally, C.A.: “A Viscosity Correlation for Gas-Saturated Crude Oils,” Trans., AIME (1959) 216, 23. 77. Aziz, K., Govier, G.W., and Fogarasi, M.: “Pressure Drop in Wells Producing Oil and Gas,” J. Cdn. Pet. Tech. (July–September 1972) 38. 78. Abu-Khamsin, S.A. and Al-Marhoun, M.A.: “Development of a New Correlation for Bubblepoint Oil Viscosity,” Arabian J. Sci. & Eng. (April 1991) 16, No. 2A, 99. 79. Simon, R., Rosman, A., and Zana, E.: “Phase-Behavior Properties of CO2-Reservoir Oil Systems,” SPEJ (February 1978) 20. 80. Abdul-Majeed, G.H., Kattan, R.R., and Salman, N.H.: “New Correlation for Estimating the Viscosity of Undersaturated Crude Oils,” J. Cdn. Pet. Tech. (May–June 1990) 29, No. 3, 80. 81. Khan, S.A. et al.: “Viscosity Correlations for Saudi Arabian Crude Oils,” paper SPE 15720 presented at the 1987 SPE Middle East Oil Technical Conference and Exhibition, Manama, Bahrain, 8–10 March. 82. Jossi, J.A., Stiel, L.I., and Thodos, G.: “The Viscosity of Pure Substances in the Dense Gaseous and Liquid Phases,” AIChE J. (1962) 8, 59. 83. Stiel, L.I. and Thodos, G.: “The Viscosity of Nonpolar Gases at Normal Pressures,” AIChE J. (1961) 7, 611. 84. Weinaug, C.F. and Katz, D.L.: “Surface Tensions of Methane-Propane Mixtures,” Ind. & Eng. Chem. (1943) 35, 239. 85. Macleod, D.B.: “On a Relation Between Surface Tension and Density,” Trans., Faraday Soc. (1923) 19, 38. 86. Nokay, R.: “Estimate Petrochemical Properties,” Chem. Eng. (23 February 1959) 147. 87. Katz, D.L. and Saltman, W.: “Surface Tension of Hydrocarbons,” Ind. & Eng. Chem. (January 1939) 31, 91. 88. Katz, D.L., Monroe, R.R., and Trainer, R.P.: “Surface Tension of Crude Oils Containing Dissolved Gases,” Pet. Tech. (September 1943). 89. Standing, M.B. and Katz, D.L.: “Vapor-Liquid Equilibria of Natural Gas-Crude Oil Systems,” Trans., AIME (1944) 155, 232. 90. Firoozabadi, A. et al.: “Surface Tension of Reservoir Crude-Oil/Gas Systems Recognizing the Asphalt in the Heavy Fraction,” SPERE (February 1988) 265. 91. Ramey, H.J. Jr.: “Correlations of Surface and Interfacial Tensions of Reservoir Fluids,” paper SPE 4429 available from SPE, Richardson, Texas (1973). 92. Wilke, C.R.: “A Viscosity Equation for Gas Mixtures,” J. Chem. Phy. (1950) 18, 517. 93. Sigmund, P.M.: “Prediction of Molecular Diffusion at Reservoir Conditions. Part I—Measurement and Prediction of Binary Dense Gas Diffusion Coefficients,” J. Cdn. Pet. Tech. (April–June 1976) 48. 94. Christoffersen, K.: “High-Pressure Experiments with Application to Naturally Fractured Chalk Reservoirs. 1. Constant Volume Diffusion. 2. Gas-Oil Capillary Pressure,” Dr.Ing. dissertation, U. Trondheim, Trondheim, Norway (1992). 95. Renner, T.A.: “Measurement and Correlation of Diffusion Coefficients for CO2 and Rich-Gas Applications,” SPERE (May 1988) 517; Trans., AIME, 285. 96. Hadden, S.T.: “Convergence Pressure in Hydrocarbon Vapor-Liquid Equilibra,” Chem. Eng. Prog. (1953) 49, No. 7, 53. 97. Rowe, A.M. Jr.: “Applications of a New Convergence Pressure Concept to the Enriched Gas Drive Process,” PhD dissertation, U. of Texas, Austin, Texas (1964). 98. Rowe, A.M. Jr.: “The Critical Composition Method—A New Convergence Pressure Method,” SPEJ (March 1967) 54; Trans., AIME, 240. 99. Hoffmann, A.E., Crump, J.S., and Hocott, C.R.: “Equilibrium Constants for a Gas-Condensate System,” Trans., AIME (1953) 198, 1. 45
100. Whitson, C.H. and Torp, S.B.: “Evaluating Constant Volume Depletion Data,” JPT (March 1983) ; Trans., AIME, 275. 101. Brinkman, F.H. and Sicking, J.N.: “Equilibrium Ratios for Reservoir Studies,” Trans., AIME (1960) 219, 313. 102. Wilson, G.M.: “Calculation of Enthalpy Data From a Modified Redlich-Kwong EOS,” Advances in Cryogenic Eng. (1966) 11, 392. 103. Wilson, G.M.: “A Modified Redlich-Kwong EOS, Application to General Physical Data Calculations,” paper 15c presented at the 1969 AIChE Natl. Meeting, Cleveland, Ohio. 104. Edmister, W.C.: “Applied Hydrocarbon Thermodynamics, Part 4: Compressibility Factors and Equations of State,” Pet. Ref. (April 1958) 37, 173. 105. Canfield, F.B.: “Estimate K-Values with the Computer,” Hydro. Proc. (April 1971) 137. 106. Standing, M.B.: “A Set of Equations for Computing Equilibrium Ratios of a Crude Oil/Natural Gas System at Pressures Below 1,000 psia,” JPT (September 1979) 1193. 107. Glasø, O. and Whitson, C.H.: “The Accuracy of PVT Parameters Calculated From Computer Flash Separation at Pressures Less Than 1,000 psia,” JPT (August 1980) 1811. 108. Galimberti, M. and Campbell, J.M.: “Dependence of Equilibrium Vaporization Ratios (K-Values) on Critical Temperature,” Proc., 48th NGPA Annual Convention (1969) 68. 109. Galimberti, M. and Campbell, J.M.: “New Method Helps Correlate K Values for Behavior of Paraffin Hydrocarbons,” Oil & Gas J. (November 1969) 64. 110. Roland, C.H.: “Vapor Liquid Equilibrium for Natural Gas-Crude Oil Mixtures,” Ind. & Eng. Chem. (1945) 37, 930. 111. Lohrenz, J., Clark, G.C., and Francis, R.J.: “A Compositional Material Balance for Combination Drive Reservoirs With Gas and Water Injection,” JPT (November 1963) 1233; Trans., AIME, 228. 112. Whitson, C.H. and Michelsen, M.L.: “The Negative Flash,” Fluid Phase Equilibria (1989) 53, 51.
46
113. Rzasa, M.J., Glass, E.D., and Opfell, J.B.: “Prediction of Critical Properties and Equilibrium Vaporization Constants for Complex Hydrocarbon Systems,” Chem. Eng. Prog. (1952) 2, 28. 114. Rowe, A.M. Jr.: “Internally Consistent Correlations for Predicting Phase Compositions for Use in Reservoir Composition Simulators,” paper SPE 7475 presented at the 1978 SPE Annual Technical Conference and Exhibition, Houston, 1–3 October.
SI Metric Conversion Factors Å 1.0* E*01 +nm °API 141.5/(131.5)°API) +g/cm3 bar 1.0* E)05 +Pa bbl 1.589 873 E*01 +m3 Btu/lbm mol 2.236 E)03 +J/mol cp 1.0* E*03 +Pa@s cSt 1.0* E*06 +m2/s dyne/cm 1.0* E)00 +mN/m ft 3.048* E*01 +m E*02 +m2 ft2 9.290 304* ft3 2.831 685 E*02 +m3 ft3/lbm mol 6.242 796 E*02 +m3/kmol °F (°F*32)/1.8 +°C °F (°F)459.67)/1.8 +K E)00 +cm2 in.2 6.451 6* lbm 4.535 924 E*01 +kg lbm mol 4.535 924 E*01 +kmol psi 6.894 757 E)00 +kPa E*01 +kPa*1 psi*1 1.450 377 °R 5/9 +K *Conversion factor is exact.
PHASE BEHAVIOR
Chapter 4
EquationĆofĆState Calculations 4.1 Introduction Cubic equations of state (EOS’s) are simple equations relating pressure, volume, and temperature (PVT). They accurately describe the volumetric and phase behavior of pure compounds and mixtures, requiring only critical properties and acentric factor of each component. The same equation is used to calculate the properties of all phases, thereby ensuring consistency in reservoir processes that approach critical conditions (e.g., miscible-gas injection and depletion of volatile-oil/gas-condensate reservoirs). Problems involving multiphase behavior, such as low-temperature CO2 flooding, can be treated with an EOS, and even water-/hydrocarbon-phase behavior can be predicted accurately with a cubic EOS. Volumetric behavior is calculated by solving a simple cubic equation, usually expressed in terms of Z+pv/RT, Z 3 ) A 2 Z 2 ) A 1 Z ) A 0 + 0, . . . . . . . . . . . . . . . . . . . . (4.1) where constants A0, A1, and A2 are functions of pressure, temperature, and phase composition. Phase equilibria are calculated with an EOS by satisfying the condition of chemical equilibrium. For a two-phase system, the chemical potential of each component in the liquid phase mi (x) must equal the chemical potential of each component in the vapor phase mi ( y), mi ( x)+mi ( y). Chemical potential is usually expressed in terms of fugacity, fi , where mi +RT ln fi )li (T ) and li (T ) are constant terms that drop out in most problems.1-3 It is readily shown that the condition mi (x)+mi ( y) is satisfied by the equal-fugacity constraint, fLi +fvi , where fugacity is given by R
f ln f i + ln i + 1 RT yi p
ŕ ǒēnēp * RTVǓ dV * ln Z.
. . . . . . (4.2)
i
V
Other thermodynamic properties, such as Helmholz energy, enthalpy, and entropy, can be readily defined in terms of the fugacity coefficient. Michelsen4 gives a particularly compact and useful discussion of the relation between thermodynamic properties aimed at making efficient EOS calculations. A component material balance is also required to solve vapor/liquid equilibrium problems: zi +Fv yi )(1*Fv )xi , where Fv +mole fraction of the vapor phase+nv /(nv )nL ). Integrating the component balance in the two-phase flash calculation is discussed in Sec. 4.3.1. Solving phase equilibria with an EOS is a trial-and-error procedure, requiring considerable computations. With today’s computers, however, the task is fast and reliable. The accuracy of EOS predictions has also improved considerably during the past 15 years, EQUATION-OF-STATE CALCULATIONS
during which emphasis has been on improved liquid volumetric predictions and treating the heptanes-plus fraction (Chap. 5). This chapter provides the equations and algorithms necessary for calculating phase and volumetric behavior of reservoir fluids with a cubic EOS. Sec. 4.2 reviews the most important cubic equations, starting with van der Waals’5 EOS from 1873 and concluding with the method of volume translation, which has greatly improved the volumetric capabilities of cubic EOS’s. In Secs. 4.3 through 4.5, we present algorithms for solving vapor/ liquid equilibrium (VLE) problems, including the two-phase flash, phase-stability-test, and saturation-pressure calculations. Reference is also made to methods for solving three-phase and criticalpoint calculations. Sec. 4.6 deals specifically with compositional gradients with depth caused by gravity and thermal diffusion. Finally, Sec. 4.7 covers how to “tune” an EOS to match experimental PVT data (see also Appendix C). 4.2 Cubic EOS's Since the introduction of the van der Waals EOS, many cubic EOS’s have been proposed—e.g., the Redlich and Kwong6 EOS (RK EOS) in 1949, the Peng and Robinson7 EOS (PR EOS) in 1976, and the Martin8 EOS in 1979, to name only a few.9-15 Most of these equations retain the original van der Waals repulsive term RT/(v*b), modifying only the denominator in the attractive term. The RedlichKwong equation has been the most popular basis for developing new EOS’s. Another trend has been to propose generalized three-, four-, and five-constant cubic equations that can be simplified to the PR EOS, RK EOS, or other familiar forms. Kumar and Starling16,17 use the most general five-constant cubic EOS to fit volumetric and phase behavior of nonpolar compounds, although they do not apply the equation to mixtures. Most petroleum engineering applications rely on the PR EOS or a modification of the RK EOS. Several modified Redlich-Kwong equations have found acceptance, with Soave’s18 modification (SRK EOS) being the simplest and most widely used. Unfortunately the SRK EOS yields poor liquid densities. Zudkevitch and Joffe19 proposed a modified RK EOS, the ZJRK EOS, where both EOS constants are corrected by temperature-dependent functions, resulting in improved volumetric predictions. Yarborough11 proposed a generalized form of the ZJRK EOS for petroleum reservoir mixtures. The PR EOS is comparable with the SRK EOS in simplicity and form. Peng and Robinson7 report that their equation predicts liquid densities better than the SRK EOS, although PR EOS densities are usually inferior to those calculated by the ZJRK EOS. A distinct advantage of the Peng-Robinson and Soave-Redlich-Kwong equa1
van der Waals also stated the critical criteria that are used to define the two EOS constants a and b—namely, that the first and second derivatives of pressure with respect to volume equal zero at the critical point of a pure component.
ǒēpēvǓ
p c,T c,v c
+
ǒēēvpǓ 2
2 p ,T ,v c c c
+ 0. . . . . . . . . . . . . . . . . . . (4.5)
Martin and Hou21 show that this constraint is equivalent to the condition (Z*Zc )3+0 at the critical point. Fig. 4.1 shows the p-v relation of a pure compound for TtTc , T+Tc , and TuTc , indicating the inflection point on the critical isotherm that represents the van der Waals critical criteria. Imposing Eq. 4.5 on Eq. 4.3 and specifying pc and Tc (as opposed to specifying two of the other critical properties), the constants a and b in the van der Waals equation are given by a + 27 64
R 2 T c2 pc
R Tc and b + 1 p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.6) 8 c The critical volume is given by vc +(3/8)( RTc /pc ), resulting in a constant critical compressibility factor. Zc +
pc vc + 3 + 0.375. 8 R Tc
. . . . . . . . . . . . . . . . . . . . . . . (4.7)
The van der Waals equation also can be written in terms of the Z factor (Z+pv/RT ). Z 3 * (B ) 1) Z 2 ) A Z * AB + 0 , Fig. 4.1—p-V relation of a pure component at subcritical, critical, and supercritical temperatures.
tions, where a simple temperature-dependent correction is used for EOS constant A, is reproducibility. The ZJRK EOS’s rely on tables or complex functions to represent the highly nonlinear correction terms for EOS constants A and B. Peneloux et al.’s20 volume-translation method modifies a twoconstant cubic equation by introducing a third EOS constant, c, without changing the equilibrium calculations of the original twoconstant equation. The volume-translation constant c eliminates the inherent volumetric deficiency suffered by all two-constant equations, and, for practical purposes, volume translation makes any two-constant EOS as accurate as any three-constant equation.12-15 4.2.1 van der Waals5 Equation. van der Waals proposed the first cubic EOS in 1873. The van der Waals EOS gives a simple, qualitatively accurate relation between pressure, temperature, and molar volume. p + RT * a2 , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.3) v*b v where a+“attraction” parameter, b+“repulsion” parameter, and R+universal gas constant. Comparing this equation with the ideal gas law, p+RT/v, we see that the van der Waals equation offers two important improvements. First, the prediction of liquid behavior is more accurate because volume approaches a limiting value, b, at high pressures, lim v ǒ p Ǔ + b , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.4)
p ³ R
where b is sometimes referred to as the “covolume” (effective molecular volume). The term RT/(v*b) dictates liquid behavior and physically represents the repulsive component of pressure on a molecular scale. The van der Waals equation also improves the description of nonideal gas behavior, where the term RT/(v*b) approximates ideal gas behavior ( p[RT/v) and the term a/v2 accounts for nonideal behavior. The a/v2 term reduces system pressure and traditionally is interpreted as the attractive component of pressure. 2
. . . . . . . . . . . . . . . (4.8)
p pr where A + a + 27 2 64 T r (RT) 2 and B + b
pr p + 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.9) RT 8 Tr
Abbott22 gives an interesting historical review of the van der Waals EOS, its strengths and weaknesses, and its analogy to other cubic EOS’s. 4.2.2 Redlich-Kwong6 Equations. The RK EOS is a p + RT * . . . . . . . . . . . . . . . . . . . . . . . . (4.10) v * b v (v ) b) or, in terms of Z factor, Z 3 * Z 2 ) ǒ A * B * B 2 Ǔ Z * AB + 0 and Z c + 1ń3 ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.11)
with EOS constants defined as R 2T 2 a + W oa p c a(T r), c
. . . . . . . . . . . . . . . . . . . . . . . . . . . (4.12a)
where W oa + 0.42748; RT b + W ob p c , c
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.12b)
+ 0.08664; p pr A+a + W oa 2 a(T r), . . . . . . . . . . . . . . . . . . . . (4.12c) (RT) 2 Tr
where
W ob
where a(T r) + T *0.5 ; r p pr and B + b + W ob . . . . . . . . . . . . . . . . . . . . . . . . . (4.12d) RT Tr The fugacity expression for pure components is
ǒ
Ǔ
f ln p + ln f + Z * 1 * ln(Z * B) * A ln 1 ) B . B Z . . . . . . . . . . . . . . . . . . . . (4.13) PHASE BEHAVIOR
TABLE 4.1—BIP’s FOR THE PR EOS AND SRK EOS PR EOS*
SRK EOS**
N2
CO2
H2 S
N2
CO2
H2 S
N2
—
—
—
—
—
—
CO2
0.000
—
—
0.000
—
—
0.120
—
H2 S
0.130
0.135
—
0.120†
C1
0.025
0.105
0.070
0.020
0.120
0.080
C2
0.010
0.130
0.085
0.060
0.150
0.070
C3
0.090
0.125
0.080
0.080
0.150
0.070
i-C4
0.095
0.120
0.075
0.080
0.150
0.060
C4
0.095
0.115
0.075
0.080
0.150
0.060
i-C5
0.100
0.115
0.070
0.080
0.150
0.060
C5
0.110
0.115
0.070
0.080
0.150
0.060
C6
0.110
0.115
0.055
0.080
0.150
0.050
C7 +
0.110
0.115
0.050‡
0.080
0.150
0.030‡
*Nonhydrocarbon
BIP’s from Nagy and
**Nonhydrocarbon
Shirkovskiy.24
Use for both the original PR EOS (Ref. 7) and modified PR EOS (Ref. 25).
BIP’s from Reid et al.3
†Not reported by Reid et al.3 ‡Should decrease gradually with increasing carbon number.
The cubic Z-factor equation can readily be solved with an analytical or a trial-and-error approach.1,2 One or three real roots may exist, where the smallest root (assuming that it is greater than B) is typically chosen for liquids and the largest root is chosen for vapors. The middle root is always discarded as a nonphysical value. For mixtures, the choice of lower or upper root is not known a priori and the correct root is chosen as the one with the lowest normalized Gibbs energy, g *,23
ȍy N
g *y +
ln f i ǒ yǓ
i
i+1
ȍx N
and g *x +
ln f i ǒ x Ǔ , . . . . . . . . . . . . . . . . . . . . . . . . . (4.14)
i
i+1
where yi and xi +mole fractions of vapor and liquid, respectively, and fi +multicomponent fugacity given (for a vapor phase) by ln
B fi + ln f i + i (Z * 1) * ln(Z * B) B yi p )A B
ǒ
Bi 2 * B A
ȍy A N
j
j+1
Ǔ
ij
ǒ
Ǔ
ln 1 ) B . Z
. . . . . . . (4.15)
The traditional quadratic mixing rule is used for A, and a linear mixing rule is used for B. For a vapor phase with composition yi , these are given by
ȍȍ y y A N
A+
N
i j
ij ,
i+1 j+1
ȍy B , N
B+
i
i
i+1
and A ij + ǒ1 * k ijǓ ǸA i A j , . . . . . . . . . . . . . . . . . . . . . . . (4.16) where kij +binary-interaction parameters (BIP’s), where kii +0 and kij +kji . Usually, kij +0 for most hydrocarbon/hydrocarbon (HC/ HC) pairs, except perhaps C1/C7) pairs. Nonhydrocarbon/HC kij are usually nonzero, where kij [0.1 to 0.15 for N2/HC and CO2/HC pairs (Table 4.1).3,24,25 EQUATION-OF-STATE CALCULATIONS
Many students of the RK EOS have been intrigued by its simplicity, accuracy, and the pleasure of deriving its thermodynamic properties. This has led to innumerable attempts to improve and extend the original Redlich-Kwong equation. Certainly hundreds, if not thousands, of technical papers and theses have been written about the RK EOS. With the advent of digital computers, this “craze” developed into what Abbott10 called the Redlich-Kwong decade (1967–77). Abbott claims that the remarkable success of the RK EOS results from its excellent prediction of the second virial coefficient (securing good performance at low densities) and reliable predictions at high densities in the supercritical region. This latter observation results from the compromise fit of densities in the near-critical region; all components have a critical compressibility factor of Z c +1/3, where, in fact, Z c ranges from 0.29 for methane to t0.2 for heavy C7) fractions. The Redlich-Kwong value of Z c +1/3 is reasonable for lighter hydrocarbons but is unsatisfactory for heavier components. 4.2.3 Soave-Redlich-Kwong. Several attempts have been made to improve VLE predictions of the RK EOS by introducing a component-dependent correction term a for EOS constant A. Soave18 used vapor pressures to determine the functional relation for the correction factor used in Eq. 4.12, a + ƪ1 ) mǒ1 * T r 0.5 Ǔƫ
2
and m + 0.480 ) 1.574 w * 0.176 w 2. . . . . . . . . . . . . . (4.17) Acentric factor w is defined in Chap. 5, and values for pure components can be found in Appendix A. Table 4.1 gives nonhydrocarbon BIP’s for the SRK EOS as recommended by Reid et al.3; kij +0 is generally recommended for HC/HC pairs. The Soave-Redlich-Kwong equation is the most widely used RK EOS proposed to date even though it grossly overestimates liquid volumes (and underestimates liquid densities) of petroleum mixtures. The present use of the SRK EOS results from historical and practical reasons. It offers an excellent predictive tool for systems requiring accurate predictions of VLE and vapor properties. Volume translation (discussed in Sec. 4.2.6) is highly recommended, if not mandatory, when liquid densities are needed from the EOS. The Pedersen et al.26,27 C7) characterization method is recommended when the SRK EOS is used. 3
plicity and overall accuracy (particularly when used with volume translation). The ZJRK EOS is surprisingly accurate for both liquid and vapor property estimations, where its main disadvantage is the complexity of functions used to represent temperature-dependent corrections for the EOS constants A and B.
0.09 0.08
4.2.5 Peng-Robinson.7 In 1976, Peng and Robinson proposed a two-constant equation that created great expectations for improved EOS predictions and improved liquid-density predictions in particular. The PR EOS is given by
0.07 0.06 0.05
a . . . . . . . . . . . . . . (4.19) p + RT * v * b v(v ) b) ) b(v * b)
0.04 0.03
or, in terms of Z factor, 0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9 1.0
Reduced Temperature
Z 3 * (1 * B)Z 2 ) ǒ A * 3B 2 * 2B ǓZ * ǒAB * B 2 * B 3Ǔ + 0 and Z c + 0.3074 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.20)
0.45
The EOS constants are given by
0.40
R 2T 2 a + W oa p c a, c
0.35 0.30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.21a)
where W oa + 0.45724;
0.25
RT b + W ob p c , c
0.20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.21b)
where W ob + 0.07780; 0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9 1.0
Reduced Temperature Fig. 4.2—Temperature and component-dependent EOS terms W oaa(T r, w) and W oaa(T r, w) for the ZJRK EOS (from Yarborough11).
a + ƪ1 ) mǒ1 * ǸT rǓƫ ; . . . . . . . . . . . . . . . . . . . . . . (4.21c) 2
and m + 0.37464 ) 1.54226 w * 0.26992 w 2 .
. . . . . . (4.21d)
al.25
4.2.4 Zudkevitch-Joffe-Redlich-Kwong. Zudkevitch and Joffe19 proposed a novel procedure for improving the volumetric predictions of the RK EOS without sacrificing VLE capabilities of the original equation. They suggest that the EOS constants A and B should be corrected as functions of temperature to match saturated liquid densities and liquid fugacities. They show that vapor fugacities and fugacity ratios (K values) remain essentially unaffected and that their procedure does not greatly affect vapor densities. Shortly after the original modification appeared, Joffe et al.28 suggested that vapor pressures should be used instead of liquid fugacities. This is the approach used today in what is still referred to as the Zudkevitch-Joffe modification, the ZJRK EOS. Haman et al.29 proposed the correction terms a and b for EOS constants A and B in equation form for pure paraffins. Yarborough11 proposed generalized a and b charts for petroleum reservoir fluids that include heavy petroleum fractions. R 2T 2 a + W oa p c T r*0.5 aǒ T r , w Ǔ c RT and b + W ob p c bǒ T r , w Ǔ . c
and Robinson and Peng30 proposed a In 1979, Robinson et modified expression for m that is recommended for heavier components (wu0.49). m + 0.3796 ) 1.485w * 0.1644w 2 ) 0.01667w 3 . . . . . . . . . . . . . . . . . . . . . (4.22) Fugacity expressions are given by f ln p +ln f + Z * 1 * ln(Z* B) *
and ln
A ln 2 Ǹ2 B
ƪ
Z ) ǒ1 ) Ǹ2ǓB
Z * ǒ1 * Ǹ2ǓB
ƫ
fi B + ln f i + i (Z * 1) * ln(Z * B) B yi p )
A 2 Ǹ2 B
ǒ
Bi 2 * B A
ȍyA N
j
j+1
Ǔƪ
ij
ln
Z ) ǒ1 ) Ǹ2ǓB
Z * ǒ1 * Ǹ2ǓB
ƫ
,
. . . . . . . . . . . . . . . . . . . . . . . (4.18)
. . . . . . . . . . . . . . . . . . . . (4.23)
Unfortunately, the temperature-dependent functions are complex because they are represented by higher-order polynomials or cubic splines (see Fig. 4.2). The behavior of these functions is highly nonlinear near Tr +1, and a discontinuity is introduced by setting the correction factors a+b+1 at Tr y1. A single set of a and b corrections is not used in the industry, making reproducing results from one version to another difficult. Preferably, a table of a and b correction factors should be provided when reporting a fluid characterization based on a ZJRK EOS. Two Redlich-Kwong modifications, the SRK EOS and ZJRK EOS, have found widespread application to petroleum reservoir fluids. The Soave equation is sometimes preferred because of its sim-
where traditional mixing rules (Eq. 4.16) are used in the derivation of the multicomponent fugacity expression. The PR EOS does not calculate inferior VLE’s compared with the RK EOS equations, and the temperature-dependent correction term for EOS constant A is very similar to the Soave correction. The largest improvement offered by the PR EOS is a universal critical compressibility factor of 0.307, which is somewhat lower than the Redlich-Kwong value of one-third and closer to experimental values for heavier hydrocarbons. The difference between PR EOS and SRK EOS liquid volumetric predictions can be substantial, although, in many cases, the error in oil densities is unacceptable from both equations. Some evidence exists that the PR EOS underpredicts sat-
4
PHASE BEHAVIOR
TABLE 4.2—JHAVERI-YOUNGREN31 VOLUME-TRANSLATION CORRELATION FOR C7) FRACTIONS WITH THE PR EOS s i + 1 * A 0ńM
A1 i
A0
A1
Paraffins
2.258
0.1823
Naphthenes
3.004
0.2324
Aromatics
2.516
0.2008
Hydrocarbon Family
TABLE 4.3—VOLUME-TRANSLATION COEFFICIENTS (si +ci /bi ) FOR PURE COMPOUNDS FOR THE PR EOS AND SRK EOS Component
PR EOS
SRK EOS
N2
*0.1927
*0.0079
CO2
*0.0817
0.0833
Fig. 4.3—p-V diagram of a pure component as calculated by a cubic EOS illustrating the van der Waals’s “loop” defining vapor pressure by the equal-area rule.
H2 S
*0.1288
0.0466
C1
*0.1595
0.0234
uration pressure of reservoir fluids compared with the SRK EOS, thereby requiring somewhat larger HC/HC (C1/C7)) BIP’s for the PR EOS. In review, the Peng-Robinson and Soave-Redlich-Kwong equations are the two most widely used cubic EOS’s. They provide the same accuracy for VLE predictions and satisfactory volumetric predictions for vapor and liquid phases when used with volume translation.
C2
*0.1134
0.0605
C3
*0.0863
0.0825
i-C4
*0.0844
0.0830
n-C4
*0.0675
0.0975
i-C5
*0.0608
0.1022
n-C5
*0.0390
0.1209
n-C6
*0.0080
0.1467
n-C7
0.0033
0.1554
n-C8
0.0314
0.1794
n-C9
0.0408
0.1868
n-C10
0.0655
0.2080
4.2.6 Volume Translation. In 1979, Martin8 proposed a new concept in cubic EOS’s, volume translation. His application was to ease the comparison of his proposed generalized EOS with previously published equations. In an independent study, Peneloux et al.20 used volume translation to improve volumetric capabilities of the SRK EOS. Peneloux et al.’s key contribution was to show that the volume shift does not affect equilibrium calculations for pure components or mixtures and therefore does not affect the original VLE capabilities of the SRK EOS. Volume translation works equally well with any two-constant EOS, as Jhaveri and Youngren31 show for the Peng-Robinson equation. Volume translation solves the main problem with two-constant EOS’s, poor liquid volumetric predictions. A simple correction term is applied to the EOS-calculated molar volume. v + v EOS * c,
ǒ f viǓ
modified+
ǒ
ȍx c N
i i
i+1
ȍy c , N
and v v + v vEOS *
i i
. . . . . . . . . . . . . . . . . . . . . . . (4.25)
i+1
and v EOS where v EOS v +EOS-calculated liquid and vapor molar volL umes, respectively; xi and yi +liquid and vapor compositions, respectively; and ci +component-dependent volume-shift parameEQUATION-OF-STATE CALCULATIONS
and ǒ f LiǓ
Ǔ
ǒf viǓ original exp * c i p RT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.24)
where v+corrected molar volume, vEOS+EOS-calculated volume, and c+component-specific constant. The shift in volume is actually equivalent to adding a third constant to the EOS but is special because equilibrium conditions are unaltered. This is readily seen for a pure component, where the van der Waals “loop” (Fig. 4.3) defines vapor pressure by making the areas above and below the p+pv line on a p-v plot equal. Shifting the p-v plot to the left or right along the volume axis does not change the equal-area (fugacity) balance, and it can be readily seen that vapor-pressure predictions are unaltered by introducing the volume-shift term c. Peneloux et al.20 also show that multicomponent VLE is unaltered by introducing the correction term as a mole-fraction average. v L + v LEOS *
ters. When the volume shift is introduced to the EOS for mixtures, the resulting expressions for fugacity are
modified+
ǒ
(f Li) original exp * c i
Ǔ
p . RT
. . . . . . . . . . (4.26)
This implies that fugacity ratios are unaltered by the volume shift, ǒ f Li ń f viǓ modified+ ǒf Li ń f viǓ original .
. . . . . . . . . . . . . . . . . . (4.27)
Applications that require direct use of fugacity (e.g., compositionalgradient calculation and semisolid phase equilibrium) must include the volume-translation coefficient in the fugacity expression. Also, the constant c can be temperature dependent but cannot include pressure or composition dependence without derivation of new fugacity expressions. Peneloux et al. propose that ci be determined for each component separately by matching the saturated-liquid density at Tr +0.7. ci can actually be determined by matching the EOS to any density value at a specified pressure and temperature. Jhaveri and Youngren31 write ci as a ratio, si +ci /bi , suggesting the following equation for C7) fractions, A
si + ci ń bi + 1 * A0 ń Mi 1 .
. . . . . . . . . . . . . . . . . . . (4.28)
Table 4.2 gives A0 and A1 values, and Table 4.3 gives si values for selected pure components that have been determined by matching 5
PR EOS
S C1 through C10 paraffins fit at T+0.7 — Jhaveri-Youngren for paraffins Methane Concentration, mol%
Fig. 4.4—Variation of volume-translation parameter si +ci /bi vs. molecular weight.
the saturated liquid density at Tr +0.7. Fig. 4.4 shows the variation of si with M. Volume translation can be applied to any two-constant cubic equation, thereby eliminating the volumetric deficiency suffered by all two-constant equations. For practical purposes volume translation makes any two-constant EOS as accurate as any three-constant equation12-15 (see Fig. 4.5). 4.3 TwoĆPhase Flash Calculation The isothermal two-phase flash calculation is the workhorse of most EOS applications. The problem consists of defining the amounts and compositions of equilibrium phases, usually liquid and vapor, given the pressure, temperature, and overall composition. An inherent obstacle to solving this problem is not knowing whether two equilibrium phases form at the specified pressure and temperature. The mixture may exist as a single phase or may split into two or more phases. The algorithms presented in this section assume that a mathematical solution to the two-phase problem exists: either a solution yielding equilibrium phase compositions or a “trivial” solution. Even when the results appear physically consistent, a rigorous check of the solution with the phase-stability test (discussed in Sec. 4.4) may be required. Alternatively, defining the phase stability before a twophase flash calculation is made improves the reliability of the flash results but adds computations. Mathematically, the two-phase flash calculation can be solved by either (1) satisfying the equal-fugacity and material-balance constraints with a successive-substitution or Newton-Raphson algorithm32,33 or (2) minimizing the mixture Gibbs free energy function.34 The first approach is used almost exclusively because it is readily implemented with one of several iterative algorithms. Gibbs energy minimization has received less attention, and it is unclear whether it has any fundamental advantages over the simpler and more direct equal-fugacity approach, at least for two-phase problems. The usual constraint equations for solving the two-phase flash problem are equal fugacities and a component/phase material balance. Assuming that all other forces are negligible (e.g., gravity), the criterion of thermodynamic equilibrium is that the chemical potential of Component i in Phase 1 equals the chemical potential of Component i in Phase 2; this is true for all Components i+ 1, . . . , N (and all phases). Fugacity, fi , is a useful expression for the chemical potential, mi , where mi +RT ln fi )li (T), and the equal-chemical-potential constraint can be written as f Li + f vi ,
i + 1, . . . , N.
. . . . . . . . . . . . . . . . . . . . . . . (4.29)
This constraint can be solved numerically by use of some measure of convergence, such as 6
Fig. 4.5—Comparison of measured and EOS-calculated saturated-liquid densities of the binary system C1/C10 systems at 100°F; SW+Schmidt-Wenzel.14.
ȍǒff
Li
i+1
Ǔ t e, 2
N
vi
*1
. . . . . . . . . . . . . . . . . . . . . . . . . . . (4.30)
where e is a convergence tolerance (e.g., 1
10*13).
4.3.1 Two-Phase Split Calculation (Rachford-Rice35 Procedure). The component and phase material-balance constraints state that n total moles of feed with Composition zi distribute into nv moles of vapor with Composition yi and nL moles of liquid with Composition xi without loss of matter or chemical alteration of the component species. The material-balance constraints can be written as n + nv ) nL and n z i + n v y i ) n L x i , i + 1, . . . , N. . . . . . . . . . . . . . . . (4.31) Introducing the vapor mole fraction Fv +nv /(nL )nv ), Eq. 4.31 can be written as z i + F v y i ) (1 * F v) x i . . . . . . . . . . . . . . . . . . . . . . . . (4.32) Additionally, the mole fractions of equilibrium phases and the overall mixture must sum to unity.
ȍ y + ȍ x + ȍ z + 1. N
N
i
N
i
i+1
i
i+1
. . . . . . . . . . . . . . . . . . . . (4.33)
i+1
This constraint can be expressed as
ȍǒ y * x Ǔ + 0. N
i
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.34)
i+1
Introducing the equilibrium ratio Ki , K i + y ińx i ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.35)
the number of unknowns can be reduced from 2 N)1 ( yi , xi , and Fv ) to N)1 (Ki and Fv ). By use of the component material balance (Eq. 4.31) and by replacing yi by Ki xi , Eq. 4.34 can be solved in terms of a single variable Fv . * 1) ȍǒy * x Ǔ + ȍ 1 )z (K + 0. F (K * 1) N
h(F v) +
N
i
i
i+1
i
i+1
i
v
. . . (4.36)
i
Eq. 4.36 is usually referred to as the Rachford-Rice35 equation. Fig. 4.6 shows the function h(Fv ) for a five-component mixture. With feed composition and K values known, the only remaining unknown is Fv. h(Fv ) has asymptotes at Fv +1/(1*Ki ), where each K value gives an asymptote.36,37 Mathematically, it can be shown that the only physically meaningful solution of h(Fv )—i.e., where PHASE BEHAVIOR
Phase compositions are calculated from the material-balance equations zi xi + F v (K i * 1) ) 1 zi Ki + Ki xi . F v (K i * 1) ) 1
and y i +
. . . . . . . . . . . . . . . . (4.41)
4.3.2 EOS Two-Phase Flash Algorithm. The flash calculation is initialized by estimating a set of K values; the Wilson39 equation is commonly used.
Ki +
Fig. 4.6—Rachford-Rice35 function h(FV ) for a five-component mixture (from Ref. 37).
all Compositions xi and yi are positive—lies in the region FvmintFv tFvmax, where F v min +
1 1 * K max
and F v max +
1 . 1 * K min
. . . . . . . . . . . . . . . . . . . . . . . . . (4.37)
It can be shown that Fvmint0 and Fvmaxu1 if at least one K value is t1 and one K value is u1. This implies that the solution for h(Fv )+0 should always be limited to the region FvmintFv tFvmax. Because h(Fv ) is monotonic and the derivative hȀ(Fv )+dh/dFv can be expressed analytically, the Newton-Raphson algorithm is commonly used to solve for Fv . + F nv * F n)1 v
hǒF nvǓ hȀǒF nvǓ
hȀ(F v) + dh + * dF v
N
v
i+1
where dh + * d Fv
ȍ
Ǔƫ . . . . . . . . . . . . . . (4.42)
pr i
K values from this equation are not accurate at high pressures, which potentially cause the two-phase flash to converge incorrectly to a trivial solution. Results from a phase-stability test provide the most reliable K-value estimates for initializing the two-phase flash but are relatively expensive to obtain. Reliable K-value estimates can be taken from a converged flash of the same mixture or a “related” mixture at a pressure and temperature not too far removed from the conditions of the present flash calculation. For example, in simulating a depletion experiment with an EOS, the K values at the saturation pressure can be used as initial estimates for the flash at the first depletion stage, the converged K values from this flash can be used for the flash at the second stage, and so on at lower pressures. With estimated K values, the Rachford-Rice35 equation is solved for Fv, with the search for Fv always bounded by Fvmin and Fvmax. F v min +
1 t0 1 * K max
and F v max +
1 u 1. . . . . . . . . . . . . . . . . . . . . . . (4.43) 1 * K min
Phase compositions are calculated from the material-balance equations. Having calculated xi and yi , phase Z factors ZL and Zv and component fugacities fLi and fvi are calculated with the EOS. and Z v + F EOSǒ y, p, T Ǔ . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.44)
ȍ
z i (K i * 1)
N
i+1
zi + 0, v ) ci N
ǒ
Z L + F EOSǒ x, p, T Ǔ
2
ƪF v (Ki * 1) ) 1ƫ
2
,
. . . . (4.38)
where n+iteration counter. The first guess for Fv can be chosen arbitrarily as 0.5. In 1949, Muskat and McDowell38 proposed a solution to the twophase split calculation that is basically the same as the one proposed by Rachford and Rice35 but numerically more efficient. Introducing the quantity ci +1/(Ki *1), where ci +R for Ki +1, Muskat and McDowell proposed the following form of the function h(Fv ). h(F ) + ȍ F
ƪ
exp 5.37ǒ1 ) w i Ǔ 1 * T *1 ri
. . . . . . . . . . . . . . . . . . . . . . (4.39)
zi
ǒF v ) c i Ǔ
and f Li + F EOSǒ x, Z L, p, T Ǔ and f vi + F EOSǒ y, Z v, p, T Ǔ.
. . . . . . . . . . . . . . . . . . . . . . . (4.45)
The “normalized” Gibbs energy function, g *, of each phase is calculated from
ȍ x ln f N
g *L +
i
Li
i+1
ȍ y ln f N
and g *v +
i
vi ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . (4.46)
i+1
and the normalized mixture Gibbs energy is given by . 2
. . . . . . . . . . . . . . . . . (4.40)
g *mix + F v g *v ) (1 * F v)g *L .
. . . . . . . . . . . . . . . . . . . . (4.47)
If a Newton estimate from Eq. 4.38 with either the MuskatMcDowell or Rachford-Rice equations for h gives an estimate of Fv outside the range FvmintFv tFvmax, the Newton method should be replaced by interval bisection or modified regula falsi until convergence is achieved. Severe round-off errors may cause any solution technique to fail when both K and z of one component are very small (e.g., KN +1 10*12 and zN +1 10*20).*
If multiple Z-factor roots are found for either phase, the root with the lowest Gibbs energy should be chosen.23 For example, if three liquid Z-factor roots were calculated ( Z L1, Z L2, and Z L3), the middle root, Z L2, is automatically discarded and the two Gibbs energy functions, g *L1 and g *L3 , are calculated; f L1i are calculated with Z L1, and f L3i are calculated with Z L3. If g *L3 t g *L1, Z L3 should be chosen; otherwise, choose Z L1 for g *L1 t g *L3 . Zick* suggests that this method of choosing the Z-factor root is not fail-safe because, at early iterations in the flash calculation, the incor-
*Personal communication with A.A. Zick, Zick Technologies Inc., Portland, Oregon (1991).
*Personal communication with A.A. Zick, Zick Technologies Inc., Portland, Oregon (1985).
i+1
EQUATION-OF-STATE CALCULATIONS
7
TABLE 4.4—SEQUENCE OF FLASH CALCULATIONS TO ENSURE CORRECT SOLUTION WITH MULTIPLE ROOTS Liquid ZL Root Chosen
Possible Order of Multiple Flash Calculations
Smallest
1
n
Largest n
3
n n
Smallest
Largest n
2
4
Vapor, Zv Root Chosen
n n n
rect root may have a lower Gibbs energy than the correct root. He proposes that the flash calculation be converged completely with a consistent choice of roots (e.g., the smallest root always chosen for the liquid phase and the largest root always chosen for the vapor phase). If multiple roots in either phase are detected during this flash calculation, a second, third, and potentially fourth flash calculation must be completed, as summarized in Table 4.4. The two-phase solution with the lowest mixture Gibbs energy is chosen as the correct solution. With fugacities calculated for each phase, the fugacity constraint (Eq. 4.30) is checked. The recommended convergence tolerance is 1 10*13, although a less stringent value can be used in some applications. If convergence is not achieved, the K values can be modified with successive substitution. + K (n) K (n)1) i i
f Li(n) f (n) vi
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.48)
where the superscripts (n) and (n)1) indicate the iteration level. With new K values, the Rachford-Rice35 equation is solved again (with new values of Fvmin and Fvmax), phase compositions are calculated with the converged Fv value, phase Z factors and component fugacities are calculated from the EOS, and the fugacity constraint is rechecked. This iterative procedure is repeated until convergence is achieved. Three types of converged solutions can be obtained. 1. A physically acceptable solution is found with 0xFv x1, where Fv +0 corresponds to a bubblepoint condition, Fv +1 corresponds to a dewpoint condition, and 0tFv t1 indicates a twophase condition. 2. A physically unacceptable solution is found with Fv t0 or Fv u1,37 where the calculated equilibrium compositions satisfy the equal-fugacity constraint and the mathematical material-balance equation. This solution indicates that the mixture is thermodynamically stable as a single phase and will not split into two phases. For this solution, the calculated equilibrium compositions would coexist in thermodynamic equilibrium at the given pressure and temperature if they were mixed together in a physically meaningful proportion (creating, of course, a different mixture composition). 3. A so-called trivial solution is found where the calculated phase compositions are identical to the mixture composition and K values equal one (xi +yi +zi and Ki +1). The first solution is usually a “correct” solution. However, if a potential three-phase solution exists, the two-phase solution may represent only a local minimum in the mixture Gibbs energy surface and the mixture Gibbs energy may be reduced further by locating the three-phase solution or another two-phase solution. Michelsen32 suggests that this problem is best dealt with by use of phase-stability analysis. Whitson and Michelsen37 refer to the second solution to the flash as a “negative” flash because one of the phase mole fractions is negative (and the other phase fraction is u1). Although this condition is physically unacceptable, the solution still has practical application. For example, phase properties and compositions are continuous across the phase boundaries. Also, a nontrivial negative flash solution indicates phase stability with the same certainty as the phase-stability test, although the negative flash calculation requires better initial K-value estimates than does the phase-stability test. A trivial solution to the flash calculation should always be checked with the phase-stability test to verify that the mixture is in fact single phase. Trivial solutions arise for several reasons, the most 8
Fig. 4.7—p-T phase envelope and envelopes indicating the limit of a nontrivial negative flash and a nontrival stability test for the binary C2/n-C4 system (from Ref. 37).
common being poor initial K-value estimates (e.g., from the Wilson39 equation). A “valid” trivial solution occurs when two-phase solutions do not exist. This occurs outside the p-T envelope that Whitson and Michelsen define as the convergence-pressure envelope, where Fv !"R in the negative flash (Fig. 4.7). Along the phase boundary and near a critical point, the Newton-Raphson flash technique tends to converge to a trivial solution more readily than do successive-substitution methods. Finally, as Michelsen23 shows, the two-phase flash never converges to a trivial solution with successive substitution under the following conditions. 1. The phase-stability test indicates that the mixture is unstable. 2. The K values resulting from the stability test are used to initialize the flash calculation. 3. The mixture Gibbs energy g *1 mix at the first iteration is less than the mixture Gibbs energy g *z . The flash calculation initialized by a successful phase-stability test is the safest solution method available, albeit more expensive than a direct two-phase flash calculation. Successive substitution is the safest solution technique for the two-phase flash problem, but it becomes slow when fugacity coefficients are strongly composition dependent. The method is particularly slow near phase boundaries and critical points, where many thousands of iterations may be required to reduce the convergence criterion to an acceptable value. Successive substitution can be accelerated with one of several methods as described in Refs. 33 and 40 through 43 among others. Michelsen32 recommends the general dominant eigenvalue method44 (GDEM); he shows that this method is particularly well suited for the two-phase flash problem because two dominant eigenvalues are found near phase boundaries and the critical point. He recommends preceding each GDEM promotion (acceleration) with five successive-substitution iterations, where the GDEM K-value correction is given by + ln K (n) ) ln K (n)1) i i
Du (n) * m 2 Du (n*1) i i 1 ) m 1 ) m 2 , . . . . . . . . . (4.49)
where Du i 5 ln ǒ f Lińf viǓ and m 1 + ǒb 02 b 12 * b 01 b 22Ǔńǒb 11 b 22 * b 12 b 12Ǔ , . . . . . . . (4.50a) m 2 + ǒb 01 b 12 * b 02 b 11Ǔńǒb 11 b 22 * b 12 b 12Ǔ ,
ȍ Du N
and b jk +
ǒ n*j Ǔ Du (n*k) . i i
. . . . . (4.50b)
. . . . . . . . . . . . . . . . . . . . (4.50c)
i+1
PHASE BEHAVIOR
m1 and m2 are coefficients reflecting the relative magnitudes of dominant eigenvalues l1 and l2. Michelsen suggests that promotions be rejected (or reduced) if the mixture Gibbs energy increases after a promotion. Zick* shows that the coefficients m1 and m2 calculated with Eqs. 4.50a and 4.50b can be seriously affected by round-off error. He suggests that the substitution ejk 5(bjk *b12)/b12 eliminates the round-off problem and that this transformation of variables results in promotion coefficients m1 and m2 that can be used even near a critical point. Also, the Michelsen32 suggestion to switch to a NewtonRaphson method after two GDEM iterations is unnecessary with the modified GDEM coefficients. For most practical reservoir applications, GDEM will converge in two to three promotions (11 to 16 iterations), with near-critical problems requiring up to six promotions (31 iterations). In summary, the two-phase flash calculation can be outlined with the following step-by-step procedure. 1. Estimate K values. 2. Calculate Kmin and Kmax. 3. Solve the Rachford-Rice phase-split calculation (Eq. 4.36) for Fv, limited between Fvmin and Fvmax (Eq. 4.43). 4. Calculate phase compositions x and y (Eq. 4.41). 5. Calculate phase Z factors ZL and Zv from the EOS. 6. Calculate component fugacities fLi and fvi from the EOS. 7. Calculate phase Gibbs energy functions g *L and g *v (Eq. 4.46), determine the correct Z-factor roots of each phase (if multiple roots exist), and calculate the mixture Gibbs energy (Eq. 4.47). 8. Check the equal-fugacity constraint (Eq. 4.30). 9. (a) If convergence is reached, stop. (b) If convergence is not reached, update the K values with the fugacity ratios (Eq. 4.48) or a GDEM promotion (Eq. 4.49); alternatively, use another acceleration technique or a Newton-Raphson K-value update. 10. Check for convergence at a trivial solution (Ki !1) with the condition
ȍǒln K Ǔ N
i
2
t 10 *4.
. . . . . . . . . . . . . . . . . . . . . . . . . . (4.51)
i+1
11. If a trivial solution is not detected, return to Step 2. Otherwise, confirm the trivial solution with a stability test. For reservoir simulation, a Newton-Raphson solution to the flash problem can be used because initial K-value estimates (from earlier timesteps and neighboring gridblocks) should be reliable, and the reduced computation time of a Newton method compared with an accelerated successive-substitution method can be significant.45 Michelsen’s23 implementation of the Newton-Raphson method is considered a very efficient algorithm and is cited here directly from his original publication (with the exception of some Nomenclature changes). “The set of equations to be solved is e i(K) + ƪlnǒn vińn vǓ ) ln f viƫ * ƪlnǒn Lińn LǓ ) ln f Liƫ + 0, . . . . . . . . . . . . . . . . . . . . (4.52) where nvi and nLi +number of moles of Component i in the vapor and liquid phases, respectively. “The Jacobian matrix is given by J ij +
ēe i , ē ln K j
yielding J + B A *1 ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.56)
z n vn L with B ij + x yi d ij * 1 ) nv ) nL i i
ƪǒ Ǔ ǒ Ǔ ƫ ē ln f i ēn j
)
v
ē ln f i ēn j
L
. . . . . . . . . . . . . . . . . . . . (4.57) and A ij +
zi d * 1. . . . . . . . . . . . . . . . . . . . . . . . . . . (4.58) x i y i ij
“Since B is symmetric, we can use the decomposition B + LDL T, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.59) where L is unit lower triangular and D is diagonal with positive elements for a positive definite B. “Then, b + * AL *TD *1L *1e, . . . . . . . . . . . . . . . . . . . . . . . . (4.60) where the cost of the decomposition and the subsequent backsubstitution is only about half of that required for conventional solution of Eq. 4.54 by Gaussian elimination.” Application of the Michaelsen Newton-Raphson algorithm, as proposed here and without proper precautions, will lead to convergence problems near phase boundaries because both matrices become singular at phase boundaries and the solution will be severely affected by round-off errors. 4.4 Phase Stability One of the most difficult aspects of making VLE calculations with an EOS is knowing whether a mixture will actually split into two (or more) phases at the specified pressure and temperature. Traditionally, this problem has been solved either by conducting a two-phase flash or by making a saturation-pressure calculation; both methods are expensive and not entirely reliable. In 1982, two papers32,46 showed how the Gibbs tangent-plane criterion could be used to establish the thermodynamic stability of a phase [i.e., whether a given composition has a lower energy remaining as a single phase (stable) or whether the mixture Gibbs energy will decrease by splitting the mixture into two or more phases (unstable)]. Ref. 46 shows graphically how the Gibbs tangent-plane criterion is used to establish phase stability of simple binary systems, and Ref. 32 gives an algorithm to establish phase stability numerically. This section on phase stability follows these references closely. Phase stability deals with the question of whether a mixture can attain a lower energy by splitting into two or more phases. The Gibbs energy for n moles of mixture Composition z i considered as a homogeneous phase is given by
ȍǒn m Ǔ N
Gz +
i z
i
i+1
ȍz m . N
+n
i
zi
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.61)
i+1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.53)
The mixture will split into two phases y and x if the mixture Gibbs energy, Gmix, is less than Gz , where Gmix is given by
and the correction b with bi +Dln Ki is found from Jb + * e. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.54)
ȍǒn m Ǔ N
G mix +
i
“The Jacobian matrix is calculated from
ȍǒn N
N ēe i ēn L k ēe i + , . . . . . . . . . . . . . . . . . (4.55) J ij + ēn L k ē ln K j ē ln K j k+1
ȍ
+
EQUATION-OF-STATE CALCULATIONS
) ǒn i m i Ǔ L ; m Li + m vi + m i
vi
) n LiǓm i
i+1
ȍ nƪF y ) (1 * F ) x ƫ m . N
+ *Personal communication with A.A. Zick, Zick Technologies Inc., Portland, Oregon (1985).
i v
i+1
v i
v
i
i
. . . . . . . . . . . . . . (4.62)
i+1
9
Mole Fraction Component 1 Fig. 4.9—p-x plot of a two-component mixture exhibiting various two- and three-phase equilibrium conditions (Ref. 46).
Fig. 4.8—Gibbs energy surface for a binary system.
The Gibbs tangent-plane criterion considers the energy surface for a homogenous phase. In terms of overall mole fractions zi +ni /n with fugacities evaluated for z, the normalized Gibbs energy function, g * + GńRT, is given by
ȍz N
g *z +
i
ln f i (z) . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.63)
i+1
g *z is a normalized Gibbs energy for the mixture composition. For a binary mixture, the energy surface g * represents a curve that can be plotted vs. one of the mole fractions (Fig. 4.8). For a ternary system, the energy surface can be plotted in three dimensions ( g * vs. two of the mole fractions), but a graphical representation is not possible for systems with more than three components. Graphically, the condition of equilibrium for a binary system is established on a g * plot by drawing a straight line that is tangent to the TABLE 4.5—PHASES IN EACH PRESSURE INTERVAL Region
Phases Present
I
Only single-phase vapor, V
II
Single-phase liquid, L1 Two-phase vapor/liquid, V/L1 Single-phase vapor, V
III
Single-phase liquid, L1 Three-phase vapor/liquid/liquid, V/L1/L2 Single-phase vapor, V
IV
Single-phase liquid, L1 Liquid/liquid, L1/L2 Single-phase liquid, L2 Vapor/liquid, V/L2 Single-phase vapor, V
V
Single-phase liquid, L1 Liquid/liquid, L1/L2 Single-phase liquid, L2
10
curve at two (or more) compositions. A valid tangent plane cannot intersect the Gibbs energy surface anywhere except at the points of tangency. For example, the vapor/liquid tangent passes through the two points ǒx, g *LǓ and ǒy, g *v Ǔ in Fig. 4.8. The compositions through which the tangent passes are equilibrium phases that satisfy the equal-fugacity condition. A physically acceptable two-phase solution requires that the mixture composition lie between the two equilibrium compositions, xtzty. If z lies outside the compositions bounded by x and y (ztx or zuy), the material-balance constraint is violated and the mixture is stable. Likewise, z+y and z+x indicate stable conditions for a mixture at its dewpoint and bubblepoint, respectively. When the overall composition z lies between the equilibrium compositions (xtzty), the mixture is unstable and will split into the two equilibrium phases with compositions y and x, having a mixture Gibbs energy given by g *mix + F vg *v ) (1 * F v)g *L. with g *mix t g *z . The value of g *mix is read directly from the tangent line at the mixture composition, and the vapor mole fraction F v is given by the distance from z to y, relative to the total distance between x and y ƪF v + (z * y)ń(x * y)ƫ. Baker et al.46 discuss the mathematical conditions associated with the Gibbs tangent-plane criterion and illustrate the technique for a binary system that exhibits two- and three-phase behavior at various pressures and a fixed temperature. Fig. 4.9, a p-x diagram divided into five pressure intervals, is adapted from their example. Depending on the mixture composition, various combinations of the three potential phases [vapor (V), lower liquid (L1), and upper liquid (L2)] can form in each pressure interval. Table 4.5 shows the phases for each interval. Figs. 4.10A through 4.10G and 4.11A through 4.11F present Gibbs energy plots for Regions II, III, and IV together with the p-x diagram (Fig. 4.9). Fig. 4.10A shows the g * curve for a low pressure in Region II where only two “valleys” exist, and thereby only one tangent can be drawn. Equilibrium compositions are located at the two points where the tangent touches the g * curve, y and xL1, each of which is near the bottom of a valley. Figs. 4.10B through 4.10D show the g * curve for a higher pressure in Region II, where a middle valley develops between the two valleys exhibited in Fig. 4.10A. Only one valid tangent can be drawn, between the L1 and V valleys. This tangent is valid because it does not pass through the g * curve at compositions other than the points of tangency, xL1 and y. Two other tangents can be drawn, one yielding a liquid/liquid (L1/L2) solution between the left and middle valleys and the other yielding a liquid/vapor (L2/V) solution between the middle and right valleys. These two tangents are, however, invalid because they lie above the g * curve in violation of the tangent-plane criterion. Such tangents represent false two-phase solutions that satisfy the equal-fugacity constraint but PHASE BEHAVIOR
Developing Second Liquid Phase “Valley”
Fig. 4.10A—Gibbs energy plot for the Baker et al.46 binary example, Region II.
yield only a local minimum in the mixture Gibbs energy. False twophase solutions are difficult to detect unless one has a priori knowledge of the actual equilibrium condition. Low-temperatures and highCO2 concentrations are conditions associated with three-phase behavior that may be susceptible to false two-phase solutions. Fig. 4.10E shows the g * curve for the three-phase pressure (Region III). A single line can be drawn that is tangent to three compositions ( y, xL1, and xL2). The three-phase solution is physically valid for any composition lying between the lower liquid (xL1) and the vapor (y) compositions, with the relative amounts of each phase in a two-phase mixture being determined by the overall composition. For ztxL1 and zuy, the mixture is stable and remains as a single phase. Fig. 4.10F shows the g * curve for a pressure in Region IV where the middle valley decreases relative to the left and right valleys. This creates a curve that has two valid tangents, one representing a L1/L2 solution and the other representing a LȀ2ńV solution. Valid two-phase solutions are found for mixture compositions in either the L1/L2 interval, xL1tztxL2, or the LȀ2ńV interval xȀL2tzty. Mixture compositions outside these two intervals will remain as a stable single phase. The tangent that can be drawn between a lower liquid and vapor phase (dashed line) is not a valid two-phase solution because the tangent lies above the g * curve in the middle region of compositions (Fig. 4.10G). However, this is a potential two-phase solution that could readily be calculated and mistaken for a valid solution. In Figs. 4.10A through 4.10G, the tangent-plane solutions that pass through compositions where g * is convex have been ignored. This follows from the observation that any mixture composition with the condition ǒē 2g *ńēz 2Ǔ t 0 is intrinsically unstable,37 and any search for a solution to the tangent-plane criterion will move away from such “convex” solutions. Also, these tangents violate the tangent-plane criterion because they lie above the energy surface (see Fig. 4.11A). Baker et al.’s46 graphical interpretation of stability analysis is particularly useful for describing the Gibbs tangent-plane criterion but does not lend itself to being implemented as a numerical algorithm that can be used to calculate phase stability. Michelsen32 proposes an algorithm that determines whether a mixture will remain EQUATION-OF-STATE CALCULATIONS
Fig. 4.10B—Gibbs energy plot for the Baker et al.46 binary example: Region II, correct two-phase V/L1 solution.
single phase or split into multiple phases. Michelsen’s algorithm is similar to a flash calculation but is faster and safer (accurate K-value estimates are not needed for the stability test). The Michelsen stability test is based on locating “second-phase” compositions that have tangent planes parallel to the tangent plane of the mixture composition. If any of the parallel tangent planes lie below the tangent plane of the mixture composition, the mixture is unstable and will split into at least two phases. If all compositions having parallel tangent planes lie above the mixture tangent plane or no composition has a parallel tangent plane, the mixture is stable as a single phase. In addition, if a composition (not equal to the mixture composition) lies on the same tangent plane as the mixture, the mixture is at a bubble- or a dewpoint and the second phase is an incipient equilibrium phase. Figs. 4.11B through 4.11F graphically illustrate the Michelsen stability-test criteria for stable and unstable mixture compositions. The mathematical description of Michelsen’s stability test is not within the scope of this monograph, but his stability-test algorithm follows. Actually, two tests are usually required; one test assumes that the second phase is vapor-like, and the other assumes that the second phase is liquid-like. This corresponds to initializing the search for a second phase with two compositions where each search is conducted separately. The compositions used to initialize each search should represent “poor” guesses (i.e., very vapor-like and very liquid-like compositions) to expand the composition space being searched. One could conceivably use N stability tests (N+number of components), each starting with a pure component as the initial composition estimate, but this would be unnecessarily time consuming. Michelsen shows that locating a second-phase composition with a tangent plane parallel to the tangent plane of the mixture composition is equivalent to locating a composition y with component fugacities f yi equal to mixture component fugacities f zi times a constant, f zi + S + I, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.64) f yi 11
False V/L2 Two-Phase Equilibrium Condition
False L1/L Two-Phase Equilibrium Condition
Fig. 4.10C—Gibbs energy plot for the Baker et al.46 binary example: Region II, false two-phase V/L2 solution.
Fig. 4.10D—Gibbs energy plot for the Baker et al.46 binary example: Region II, false two-phase L1/L2 solution.
where I+constant. A successive-substitution algorithm, summarized in the following procedure, can readily be used to solve the Michelsen stability test. Note that each test is conducted separately (e.g., converging the vapor-like search first, then converging the liquid-like search). 1. Calculate the mixture fugacities, f zi ; with multiple Z-factor roots, choose the root with the lowest g *. 2. Use the Wilson equation (Eq. 4.42) to estimate initial K values.
Ǔƫ expƪ5.37(1 ) w i)ǒ1 * T *1 ri . p ri
K 1i +
. . . . . . . . . . . . . (4.42)
3. Calculate second-phase mole numbers, Yi , using the mixture composition z i and the present K-value estimates. (Y i) v + z i (K i) v or (Y i) L + z i ń(K i) L .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.65)
4. Sum the mole numbers.
ȍǒY Ǔ N
Sv +
j v
j+1
ȍǒY Ǔ . N
or S L +
j L
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.66)
j+1
5. Normalize the second-phase mole numbers to get mole fractions, yi . (y i) v +
(Y i) v
ȍǒY Ǔ N
j v
j+1
12
+
(Y i) v Sv Fig. 4.10E—Gibbs energy plot for the Baker et al.46 binary example: Region III, correct three-phase solution. PHASE BEHAVIOR
False V-L1 Two-Phase Equilibrium Condition
Fig. 4.10F—Gibbs energy plot for the Baker et al.46 binary example: Region IV, two possible correct two-phase solutions (L1/L2 or V/L2).
(Y i) L
or (y i) L+
ȍǒY Ǔ N
+
(Y i) L . SL
. . . . . . . . . . . . . . . . . . . . . (4.67)
j L
Fig. 4.10G—Gibbs energy plot for the Baker et al.46 binary example: Region IV, false two-phase V/L1 solution.
Michelsen suggests that Step 9 of the successive substitution can be accelerated with the GDEM approach with one eigenvalue (only one eigenvalue approaches 1 near the critical point in a stability test). He recommends that four successive-substitution iterations precede each promotion. The GDEM update is given by
j+1
l
6. Calculate the second-phase fugacities ( fyi )v or ( fyi )L from the EOS; with multiple Z-factor roots (for a given phase), choose the root with the lowest Gibbs energy g *. 7. Calculate the fugacity-ratio corrections for successive-substitution update of the K values. (R i) v +
f zi
1
ǒf yiǓ L f zi
2
SL .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.68) 10*12).
t e. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.69)
9. If convergence is not obtained, update the K values. K (n)1) + K (n) R (n) . i i i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.70)
10. Check whether a trivial solution is being approached using the criterion N
i
2
ȍ ln R N
b 01 +
(n) ln i
R (n*1) , i
ȍ ln R
(n*1) i
ln R (n*1) , i
. . . . . . . . . . . . . . . . . (4.72)
i+1
i+1
ȍǒln K Ǔ
Ť
b 11 , 11 * b 01
N
N
i
Ťb
and b 11 +
8. Check whether convergence is achieved (e.g., et1
ȍ(R * 1)
l+
i+1
ǒf yiǓ v S v
or (R i) L +
ƪR (n) ƫ, + K (n) K (n)1) i i i
t1
10 *4.
. . . . . . . . . . . . . . . . . . . . . . (4.71)
i+1
11. If a trivial solution is not indicated, go to Step 3 for another iteration. EQUATION-OF-STATE CALCULATIONS
where the superscript (n) is the iteration counter. Table 4.6 summarizes the interpretation of the two-part stability test. The mixture (very likely) is stable if both tests yield Sx1, if both tests converge to a trivial solution, or if one test yields Sx1 and the other converges to a trivial solution. Theoretically, it is impossible to establish without a doubt that a mixture is stable until all compositions have been tested. However, both solutions indicating stability from the two-part Michelsen test usually ensures that a mixture is in fact single phase. On the other hand, only one test indicating Su1 is sufficient to determine that a mixture is definitely unstable. For an unstable solution, the resulting K values from the stability test can be used to initialize the two-phase flash. Potentially both SL and Sv are u1, in which case the best initial K values for the flash are given by Ki +( yi )v /( yi )L +(Ki )v (Ki )L , requiring that both tests be completed (even though the first test positively indicates an unstable mixture). Fig. 4.12 shows Nghiem and Li’s47 EOS calculations identifying the phase boundary of a reservoir oil. Also shown is the envelope within the phase boundary (dashed line) where one of the stability 13
Region of Compositions Where Stability Test Converges Nontrivial
Fig. 4.11A—Gibbs energy plot for a hypothetical binary system showing a graphical interpretation of Michelsen’s32 phase-stability test for region of compositions where stability test converges nontrivial.
Fig. 4.11B—Gibbs energy plot for a hypothetical binary system showing a graphical interpretation of Michelsen’s32 phase-stability test for liquid-like feed, z, with one unstable condition, y, located.
tests converges to a trivial solution. The lower dashed line (starting from the critical point) shows where the liquid-like stability test converges to a trivial solution, and the upper dashed curve shows where the vapor-like stability test converges to a trivial solution. Inside the dashed-curve envelope, both the liquid- and vapor-like stability tests converge to a nontrivial unstable solution (both SL and
Sv are u0). Fig. 4.13 illustrates the behavior of SL and Sv vs. pressure at a fixed temperature for this system. Michelsen’s phase-stability test has many applications; the following summarizes the most important ones. 1. Determining whether a mixture composition is thermodynamically stable as a single phase. If the test indicates stability (assuming
Fig. 4.11C—Gibbs energy plot for a hypothetical binary system showing a graphical interpretation of Michelsen’s32 phase-stability test for vapor-like feed, z, with one stable condition, y, located.
Fig. 4.11D—Gibbs energy plot for a hypothetical binary system showing a graphical interpretation of Michelsen’s32 phase-stability test for liquid-like feed, z, with two unstable conditions, yL and yv, located.
14
PHASE BEHAVIOR
Fig. 4.11E—Gibbs energy plot for a hypothetical binary system showing a graphical interpretation of Michelsen’s32 phase-stability test for vapor-like feed, z, with one unstable condition, yL , located.
that both liquid- and vapor-like second phases have been tested), it is very likely that a two-phase solution does not exist. 2. With at least one unstable solution, initializing the two-phase flash calculation with K values determined from the unstable solution(s) of the stability test. This is particularly useful if K values from a converged flash at nearby conditions are not available. 3. Initializing and limiting the pressure range in a saturation-pressure calculation (see Sec. 4.5). 4. Checking the stability of a converged two-phase flash when three-phase behavior is suspected (e.g., for low-temperature and high-CO2 systems). This requires, however, two modifications of the stability test: (a) choice of appropriate initial K-value estimates for the “third”-phase search and (b) use of the converged two-phase fugaci-
Fig. 4.11F—Gibbs energy plot for a hypothetical binary system showing a graphical interpretation of Michelsen’s32 phase-stability test for liquid-like feed, z, with one unstable condition, yv , located.
ties, feqi +fvi +fLi , instead of fzi in the new search (i.e., locate a third composition y so that feqi /fyi equals a constant S, with Sx1 indicating stability; Su1 would indicate an unstable condition for the two-phase solution, thereby guaranteeing a multiphase solution).
TABLE 4.6—SUMMARY OF POSSIBLE PHASE-STABILITY-TEST RESULTS Second Phase Vapor-Like
ǒKiǓ Stable
Unstable
ǒyiǓ
+ z v i
v
Liquid-Like
ǒKiǓ
l
+
zi
ǒyiǓ
l
Probable Number of Valleys on g*
TS
TS
1
SL x1
TS
2
TS
SL x1
2
Sv x1
SL x1
3
Sv u1
TS
2
TS
SL u1
2
Sv u1
SL u1
2
Sv u1
SL x1
3
Sv x1
SL u1
3
TS+trivial solution.
EQUATION-OF-STATE CALCULATIONS
Fig. 4.12—Phase and stability-limit envelopes for a reservoir oil; stability limit represents the condition when one of the stability tests first converges to a trivial solution (from Nghiem and Li47). 15
LIQUID-lIKE SECOND PHASE VAPOR-LIKE SECOND PHASE
Nghiem et al.48 use the condition of zero tangent-plane distance, d TP +0, to solve for saturation pressure, psat, and incipient-phase composition y. d TPǒ p sat , y Ǔ + ln
ǒȍ Ǔ N
Yi
+ 0.
. . . . . . . . . . . . . . . . . (4.77)
i+1
The recommended approach for determining saturation pressure is based on a slightly different approach proposed by Michelsen49; he uses the condition TS
TS
Qǒ p sat , y Ǔ + 1 *
ȍ z ƪf (z)ńf ǒ y Ǔƫ + 0 N
i
i
i
i+1
ȍ y ǒf N
+1*
i
Ǔ
zi ń f yi
i+1
ȍY , N
+1*
i
. . . . . . . . . . . . . . . . . . . . . . . (4.78)
i+1
where incipient-phase mole fractions are defined by Fig. 4.13—Behavior of mole number sums from stability test, SL and Sv, vs. pressure for a fixed temperature; TS+trivial solution.
4.5 SaturationĆPressure Calculation For a mixture composition z at fixed temperature T, the saturationpressure calculation involves finding the pressure(s) where the mixture is in equilibrium with an infinitesimal amount of an incipient phase. In terms of a two-phase flash, the saturation pressure defines a pressure where the vapor mole fraction, Fv, equals zero or one (Fv +0 at bubblepoint and Fv +1 at dewpoint). One way to locate the saturation pressure of a mixture would be to make a 1D search in pressure for Fv +0 or 1, where the two-phase flash is converged at each pressure estimate during the search. Although this approach would be safe, it also would be very slow. Several alternative saturation-pressure algorithms are available that are both efficient and reliable when used with stability analysis. The two conditions defining a saturation pressure are that the fugacities of all components are equal in both phases, f zi + f yi , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.73) and that the mole fractions of the incipient phase, y, equal unity,
ȍ y + 1. N
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.74)
i
Expressing the incipient-phase mole fractions in terms of K values ( yi +zi Ki for a bubblepoint and yi +zi /Ki for a dewpoint), the traditional equations used to solve bubble- and dewpoint calculations, respectively, are
ȍz K + 0 N
i
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.75a)
i+1
ȍ z ńK + 0. N
and 1 *
i
i
. . . . . . . . . . . . . . . . . . . . . . . . . (4.75b)
i+1
In terms of stability analysis, the saturation-pressure condition corresponds to finding a second phase with a tangent plane that is parallel to the mixture composition’s tangent plane, with zero distance between the two tangent planes. This is equivalent to the sum of incipient-phase mole numbers equaling unity.
ȍ Y + 1. N
i
i+1
16
Yi
ȍY
.
N
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.79)
j
j+1
An efficient method to solve this equation uses a Newton-Raphson update for pressure and accelerated successive substitution (GDEM) for composition. The following procedure outlines this approach. 1. Guess a saturation type: bubble- or dewpoint. An incorrect guess will not affect convergence, but the final K values may be “upside down.” 2. Guess a pressure p *. 3. Perform Michelsen’s stability test at p *. 4. (a) If the mixture is stable for the current value of p *, this pressure represents p * the upper bound of the search for a saturation pressure on the upper curve of the phase envelope. Return to Step 1 and try a lower pressure to look for an unstable condition. (b) With an unstable condition at p *, this pressure represents the lower bound in the search for a saturation pressure on the upper curve of the phase envelope. 5. Having found an unstable solution, use the K values from the stability test to calculate incipient-phase mole numbers at bubbleand dewpoint with Eqs. 4.80a and 4.80b, respectively. Y i + z i K i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.80a) and Y i + z ińK i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.80b)
i+1
1*
yi 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.76)
If two unstable solutions were found in the stability test, use the K values for the test with the largest mole number sum S. At this point, the initialization is complete and the iteration sequence begins. 6. Calculate the normalized incipient-phase compositions. yi +
Yi
ȍY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.81)
N
j
j+1
7. Calculate phase Z factors, Zz and Zy, and component fugacities, fzi and fyi , from the EOS at the present saturation-pressure estimate. When multiple Z-factor roots are found for a given phase, the root giving the lowest Gibbs energy should be chosen. 8. Calculate fugacity-ratio corrections. f zi Ri + f yi
ǒȍ Ǔ N
Yj
*1
.
. . . . . . . . . . . . . . . . . . . . . . . . . (4.82)
j+1
PHASE BEHAVIOR
9. Update incipient-phase mole numbers with the fugacity-ratio corrections,
ƫ l, Y i(n)1) + Y i(n) ƪR (n) i
. . . . . . . . . . . . . . . . . . . . . . . . . . (4.83)
where four iterations use successive substitution (l+1) followed by a GDEM promotion with l given by l+
Ťb
11
Ť
b 11 , * b 01
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.84)
ȍ ln R N
where b 01 +
(n) ln R (n*1) i i
4.6 Equilibrium in a Gravity Field: Compositional Gradients Gibbs53 was the first to give the formula for calculating compositional variation under the force of gravity for an isothermal system. The condition of equilibrium is satisfied by the constraint m i ǒ p ref , z ref , T Ǔ + m iǒ p, z, TǓ ) M i gǒh * h refǓ ,
i+1
ȍ ln R
Michelsen52 also has proposed a critical-point calculation algorithm that is, surprisingly, as fast or faster than a two-phase flash calculation. The critical point is determined by a simple 2D search (in temperature and volume) with a function that requires only evaluation of the mixture fugacities.
N
and b 11 +
(n*1) ln R (n*1) . i i
i + 1, 2, . . . , N, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.89)
i+1
10. Calculate a new estimate of saturation pressure using a Newton-Raphson update. + p (n) p (n)1) sat sat *
where
Q (n)
ǒēQ Ǔ ēp
(n)
,
. . . . . . . . . . . . . . . . . . . . . . (4.85)
ȍ Y R ǒēfēp f1 * ēfēp f1 Ǔ N
ēQ + ēp
yi
i
i
i+1
zi
yi
. . . . . . . . . . . . . (4.86)
zi
is evaluated at Iteration (n). If searching for an upper saturation pressure, the new pressure estimate must be higher than p *. If the new estimate is lower than p *, go to Step 1 and use a new initial-pressure estimate higher than the present p * value. 11. Check for convergence. Zick* suggests the following two criteria.
Ť
and
ȍY N
1*
i
i+1
ƪ
Ť
t 10 *13
ƫ
) ȍ lnln(R ǒY ńz Ǔ N
i
i
i+1
i
2
t 10 *8. . . . . . . . . . . . . . . . . . . . . (4.87)
In addition, check for a trivial solution using the criterion
ȍǒln Yz Ǔ N
i
i+1
i
2
t 10 *4 .
. . . . . . . . . . . . . . . . . . . . . . . . . . (4.88)
12. (a) If convergence is not achieved, return to Step 6. (b) If convergence is achieved, determine the saturation type by comparing the mole fraction of the heaviest component in the mixture with that in the incipient phase, where yN tzN indicates a bubblepoint with Ki +yi /zi and yN uzN indicates a dewpoint where Ki +zi /yi , or by comparing the density of the incipient phase with that of the feed. This algorithm can be modified to search for both lower and upper saturation pressures as well as saturation temperature at a specified pressure. Michelsen50 also gives an efficient procedure for calculating the entire phase envelope, including calculations through the critical point. More recently, he presented an approximate phase-envelope algorithm51 that is up to 10 times faster than his original algorithm using a trial-and-error solution directly for pressure and temperature (component fugacities do not need to be converged at each point on the phase envelope). Surprisingly, the results are extremely close to fully converged saturation conditions and provide excellent starting estimates for a rigorous saturation-point calculation. He also shows that the approximate solution is always inside the phase envelope, thus representing an unstable thermodynamic condition. *Personal communication with A.A. Zick, Zick Technologies Inc., Portland, Oregon (1985).
EQUATION-OF-STATE CALCULATIONS
where mi +chemical potential of Component i, zref+homogeneous (single-phase) mixture at pressure pref at a reference depth href, and p+pressure and z+mixture composition at depth h. The entire system is at constant temperature (dT/dh+0). In 1930, Muskat54 provided exact solutions to Eq. 4.89 for a simplified EOS (ideal mixing). Numerical examples based on this oversimplified EOS led to the misleading conclusion that gravity has negligible effect on compositional variation in reservoir systems. In 1938, Sage and Lacey55 evaluated Eq. 4.89 using a more realistic EOS model. They provide examples showing significant variations of composition with depth for reservoir mixtures. Furthermore, they made the key observation that significant compositional variations should be expected in systems in the vicinity of a critical condition. From 1938 to 1980, the petroleum literature is apparently void of publications regarding calculation of compositional gradients. Several references during this period do, however, mention reservoirs exhibiting compositional variation. Schulte56 cites most of these references. He appears to be the first to solve Eq. 4.89 with a cubic EOS. His classic paper illustrates that significant compositional variation can result from gravity segregation in petroleum reservoirs. Schulte gives examples showing the effect of oil type (aromatic content) and interaction coefficients (used in the mixing rules of a cubic EOS) on compositional gradients. He also compares gradients calculated with the Peng-Robinson and Soave-Redlich-Kwong equations. In 1980, significant compositional gradients were reported in the Brent field, North Sea.56-58 In the Brent formation of the Brent field, a significant composition gradient was observed, with the transition from gas to oil occurring at a saturated gas/oil contact (GOC). These papers also describe the unusual transition from gas to oil in the absence of a saturated GOC. This transition occurs at a depth where the reservoir fluid is a critical mixture, with a critical temperature equal to the reservoir temperature and a critical pressure less than the reservoir pressure. Apparently, the Statfjord formation in the Brent field is an example of a reservoir with such an “undersaturated GOC.” In 1983, Holt et al.59 presented a formulation of the compositionalgradient problem that includes thermal diffusion. Example calculations in this paper were, unfortunately, limited to binary systems. Numerous publications on the subject of compositional gradient were presented in 1984 and 1985.60,61 Most of these were field case histories; in fact, a special session of the 1985 SPE Annual Technical Conference and Exhibition was dedicated to this subject.62-64 Hirschberg60 discusses the influence of asphaltenes on compositional grading. He uses a simplified two-component model with one component representing asphaltenes and the other representing the remaining deasphalted oil. He makes the observation that compositional grading in heavier oils ( go u0.85 or gAPIt35°API) can be strongly influenced by both the amount and the properties of asphaltenes, which implies that quantitatively accurate estimates of compositional grading resulting from asphaltenes are extremely difficult because of the strong dependence of calculated results on physical properties of the oil and asphaltene(s). Finally, Hirschberg discusses two mechanisms for the development of a tar mat. Riemens et al.61 present an interesting evaluation of the compositional grading in the Birba field, Oman. On the basis of isothermal gravity/chemical equilibrium (GCE) calculations and field measure17
ments of PVT data, they show that a significant compositional gradient exists. The authors also evaluate the possibility of injecting gas into the undersaturated oil zone where multicontact miscibility can develop. Montel and Gouel65 suggest an algorithm for solving the isothermal GCE problem. The procedure is only approximate because it calculates pressure with an incremental hydrostatic term instead of solving directly for pressure. They discuss the effect of fluid characterization on compositional grading and the effect of reservoir temperature and pressure. Finally, the authors suggest that including thermal diffusion may improve the reliability of calculated compositional gradients (although they do not include this effect in their study). Metcalfe et al.63 report measured variation of composition and physical properties of reservoir fluids in the Anschutz Ranch East field in the U.S. Overthrust Belt. These authors use an EOS to characterize the PVT behavior of the entire range of fluids sampled from the reservoir. However, instead of calculating the compositional variation using gravity/chemical equilibrium and the developed EOS characterization, they correlate compositional variation graphically on the basis of measured data. Creek and Schrader62 report compositional grading data for another Overthrust Belt reservoir, the East Painter field. Considerable data are presented together with comparison of measured compositional gradients and those calculated with the isothermal GCE model. They report difficulty in matching observed saturation-pressure and GOR gradients. Finally, the authors indicate that most reservoirs along the Overthrust Belt have varying degrees of compositional grading. Belery and da Silva66 present a formulation describing the combined effects of gravity and thermal diffusion for a system of zero net mass flux. After assessing various approaches for treating thermal diffusion, they selected the Dougherty and Drickamer67 method. Belery and da Silva extend this formulation (originally valid only for binary systems) to multicomponent systems. They use a field example with EOS characterization and measured gradient data from the North Sea Ekofisk field to illustrate the gravity/thermal model. Because measured PVT gradients were very scattered (probably because of sampling problems), the comparison is not quantitatively accurate (with or without thermal diffusion). However, the calculations show qualitatively the effect of thermal diffusion and are the first such calculations reported for multicomponent systems. Wheaton68 discusses an isothermal GCE model that includes the influence of capillary pressure. The addition of capillary forces was apparently justified in an effort to assist in the initialization of reservoir simulators. Simulators use capillary pressure curves to initialize saturation and pressure distributions discretely in the vertical direction. Results of the calculated examples in Wheaton’s paper suggest that neglecting compositional variations in a gas-condensate reservoir may result in large errors in the initial hydrocarbons in place. Obviously, these results are primarily a consequence of neglecting the compositional variation resulting from gravity/chemical equilibrium. Quantitatively similar results would have been obtained with or without the inclusion of capillary pressures. Finally, his observation that neglecting compositional gradients will lead to incorrect specification of initial oil and gas in place is equally applicable to gas-condensate and oil reservoirs (i.e., practically any petroleum reservoir). In his discussion of Wheaton’s paper, Chaback69 makes the observation that nonisothermal effects can be on the same order of magnitude as gravity effects. More importantly, he notes that a nonisothermal system will never reach equilibrium (zero energy flux) even though a stationary (steady-state) condition of zero net mass flux is reached. Montel70 discusses compositional grading, including comments on treating thermal diffusion. He provides an equation for calculating the Rayleigh-Darcy number that is used to indicate whether a fluid/rock system will experience convection (mechanical instability). Bedrikovetsky 71 gives an extensive discussion and formal mathematical treatment of compositional grading, including gravity, thermal, and capillary forces. The treatment yields complicated expressions, which, in a few cases, are solved for simple conditions (idealized EOS and binary systems). Many of the results are similar to those given by Muskat.54 No examples are given for multicomponent mixtures with a realistic thermodynamic model. 18
Recently, Faissat et al.72 gave a theoretical review of equilibrium formulations that include gravity and thermal diffusion. Belery and da Silva66 mention most of the formulations, but Faissat et al. formalize the thermal-diffusion term in a generic way. Unfortunately, calculations are not provided for comparing the different formulations. 4.6.1 Isothermal GCE. Eq. 4.89 gives the condition for isothermal GCE, which is sometimes written in differential form as dm i ) M i gdh + 0, i + 1, 2, . . . , N . This condition represents N equations. Together with the constraint that the sum of mole fractions z(h) must add to one,
ȍ z (h) + 1, N
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (4.90)
i+1
it is possible to solve for composition z(h) and pressure p(h) at a specified depth h. Because chemical potential can be expressed as mi +RT ln fi )l(T ), Eq. 4.89 can be expressed in terms of fugacity. ln f i ǒ p ref , z ref , TǓ + ln f i ǒ p, z, T Ǔ ) 1 M i gǒh * h refǓ , RT i + 1, 2, . . . , N. . . . . . . . . . . . . . . . . . . . . . . . . . (4.91) For convenience, we define fi (h)+fi [ p(h),z(h),T ] and fi (href)+fi ( pref,zref,T ), yielding
ƪ
f i (h) + f iǒh refǓ exp *
ƫ
M i gǒh * h refǓ , RT
i + 1, 2, . . . , N. . . . . . . . . . . . . . . . . . . . . . . . . . (4.92) The volume-translation method is widely used for correcting volumetric deficiencies of the original Soave-Redlich-Kwong and PengRobinson equations. The method involves calculating a linearly translated volume, vȀ, by adding a constant c to the molar volume, v, calculated from the original EOS, vȀ+v)c. Peneloux et al.20 show that the volume shift modifies the component fugacity as fi exp[ci ( p/RT)] (see Eqs. 4.26 and 4.96). This correction must be included in the fugacity expressions used for gradient calculations and also must be included in the pressure derivative of fugacity used in the recommended algorithm for solving the isothermal GCE problem. On the basis of the Gibbs-Duhem equation,53 combining the mechanical-equilibrium condition, dpńdh +* òg , with the GCE condition, Eq. 4.89, guarantees automatic satisfaction of the condition
ŕ ò(h)gdh . h
p(h) + pǒh refǓ )
. . . . . . . . . . . . . . . . . . (4.93)
h ref
Interestingly, the isothermal GCE equations are still valid and satisfy this condition when a saturated GOC is located between href and h [i.e., even when ò(h) is not a continuous function]. 4.6.2 Isothermal GCE Algorithm. Eqs. 4.89 and 4.90 represent equations similar to those used to calculate saturation pressure. Michelsen51 gives an efficient method for solving the saturationpressure calculation, which has been modified here to solve the GCE problem, Qǒ p, z Ǔ + 1 *
ȍ z ƪf ǒp N
~
i
i
Ǔ ń f i ǒ p, z Ǔƫ
ref, z ref
i+1
ȍY , N
+1*
i
. . . . . . . . . . . . . . . . . . . . . . . . . . (4.94)
i+1
where Y i + z i ƪ f i ǒ p ref, z refǓńf i ǒ p, z Ǔƫ . . . . . . . . . . . . . . . . . . (4.95) ~
ƪ
and f i ǒ p ref, z refǓ + f i ǒ p ref, z refǓ exp * ~
ƫ
M i gǒh * h refǓ . RT
. . . . . . . . . . . . . . . . . . . . (4.96) PHASE BEHAVIOR
An efficient algorithm for solving Eq. 4.94 uses a Newton-Raphson update for pressure and accelerated successive substitution this approach. (GDEM44) for composition. The following outlines ~ 1. Calculate fugacities of ~the reference feed f i ( y ref, z ref) and the gravity-corrected fugacity f i ( p ref, z ref) from Eqs. 4.26 and 4.96. This calculation needs to be made only once. Initial estimates of composition and pressure at h are simply values at the reference depth, z 1(h) + z ref and p 1(h) + p ref . 2. Calculate fugacities of the composition estimate z at the pressure estimate p. Calculate mole numbers from Eq. 4.95. Calculate fugacity-ratio corrections with f i ǒp ref , z refǓ ~
Ri +
f i ǒ p, zǓ
ǒȍ Ǔ N
*1
Yj
.
. . . . . . . . . . . . . . . . . . (4.97)
j+1
3. Update mole numbers using Eqs. 4.83 and 4.84. from Y (n)1) using 4. Calculate z (n)1) i i zi + Yi ń
ǒȍ Ǔ N
Yj .
. . . . . . . . . . . . . . . . . . . . . . . . . . (4.98)
j+1
5. Update the pressure estimate using a Newton-Raphson estimate. p (n)1) + p (n) *
where
ēQ + ēp
Q (n) ǒēQńēpǓ
ȍY R N
i
i+1
i
(n)
,
ǒēf ińēpǓ . f i ǒ p, z Ǔ
. . . . . . . . . . . . . . . . . . . . (4.99)
. . . . . . . . . . . . . . . . . . (4.100)
6. Check for convergence using Eq. 4.87. 7. Iterate until convergence is achieved. After finding the composition z(h) and pressure p(h) that satisfy Eqs. 4.89 and 4.90, a phase-stability test32 must be made to establish whether the solution is valid. A valid solution is single phase (thermodynamically stable). An unstable solution indicates that the calculated z and p will split into two (or more) phases, thereby making the solution invalid. If the gradient solution is unstable, then the stability-test composition y should be used to reinitialize the gradient calculation. The starting pressure for the new gradient calculation can be pref or, preferably, the converged pressure from the gradient calculation that led to the unstable solution. Note that unstable gradient solutions usually occur only a short distance beyond a saturated GOC. Locating a potential GOC requires a trial-and-error search. For a saturated GOC, three approaches might be considered: (1) stability tests, (2) negative flash calculations,37 or (3) saturation-pressure calculations. The first and second methods should be the fastest, with the negative flash probably being faster because information from previous flash calculations can be used for initialization of subsequent flash calculations. Unfortunately, an algorithm based on either the stability test or negative flash results may suffer from the fact that only trivial solutions exist over a large part of the reservoir thickness. On the other hand, either method can be used efficiently to determine the saturated GOC once a nontrivial stability condition is found. If an undersaturated GOC exists (i.e., a transition from gas to oil through a critical mixture), only a search based on saturation-pressure calculations can be used. The following algorithm is recommended for locating both saturated and undersaturated GOC’s. First, calculate the composition and pressure at the top (zT and pT ) and the bottom (z B and pB ) of the reservoir; then, calculate saturation pressures psT and psB . If the saturation types (bubblepoint/dewpoint) are the same at the top and bottom, then no GOC exists. Otherwise, a search for the GOC, hGOC, is made. A straightforward search algorithm would be interval halving based on the saturation type. At Iteration n, a solution with a dew+ h (n) for the point at depth h (n) would replace the top depth h (n)1) T next iteration, and a solution with a bubblepoint at a given depth + h (n) . The depth estimate would replace the bottom depth h (n)1) B ƫ. The ) h (n) for a given iteration is calculated from h (n) + 0.5ƪh (n) B T EQUATION-OF-STATE CALCULATIONS
number of iterations required to meet a tolerance dh would be 1.5 lnƪ(h T * h B)ńdhƫ . For example, only 13 gradient and saturation-pressure calculations would be needed to achieve dh+0.33 ft for a total thickness (h T * h B)+1,640 ft. More efficient algorithms for locating the GOC can probably be developed, particularly if a nontrivial stability solution can be located. Alternatively, Michelsen’s52 critical-point algorithm or his new method for calculating accurate approximations for saturation pressure and temperature51 may provide a good starting point for developing an improved algorithm. Whitson and Belery73 give a detailed discussion of compositional-gradient calculations, including the application of isothermal and nonisothermal compositional-gradient algorithms to reservoir fluid systems ranging from a saturated low-GOR black-oil/dry-gas system to a near-critical system. 4.7 Matching an EOS to Measured Data Most EOS characterizations (see Chap. 5) are not truly predictive74,75 because errors in saturation pressure are commonly "10%, those in densities are "5%, and compositions may be off by several mole percent for key components. Also, the EOS may predict a dewpoint incorrectly when the measured saturation condition is a bubblepoint, or vice versa. This lack of predictive capability by the EOS can be because of insufficient compositional data for the C7) fractions, inaccurate properties for the C7) fractions, inadequate BIP’s, or incorrect overall composition. The EOS characterization can be improved in a number of ways. First, however, the experimental data and fluid compositions should be checked for consistency (see Chap. 6). If the PVT data appear consistent and the fluid compositions are considered representative of the material that was analyzed in the PVT laboratory, modifying the parameters in the EOS to improve the fluid characterization will be necessary. Refs. 26 and 74 through 79 present methods for modifying the cubic EOS to fit experimental PVT data. Most of these methods modify the properties of fractions making up the C7) (Tc , pc , w, or direct multipliers on the EOS constants Wa and Wb ) and BIP’s kij between methane and C7) fractions. When an injection gas containing significant amounts of nonhydrocarbons is being studied, the kij between nonhydrocarbon and C7) fractions may also be modified. Some methods use nonlinear regression to modify the EOS parameters automatically.74,78,79 Others have tried simply to make manual adjustments to the EOS parameters through a trial-and-error approach.75,77,80 The trend is now to automate the EOS modification procedure with nonlinear regression, including large amounts of measured PVT and compositional data.81 Coats and Smart74 recommend five standard EOS modifications: Wa and Wb of methane; Wa and Wb of the heaviest C7) fraction; and kij between methane and the heaviest C7) fraction. Additional parameters (nonhydrocarbon Wa and Wb and kij ) are used for systems with significant amounts of nonhydrocarbon components. Their approach differs from other methods in that they do not use volume translation. As a result, significant methane corrections had to be applied to EOS constants Wa and Wb . Using the Coats and Smart approach with the PR EOS typically results in multipliers of the EOS constants Wa and Wb ranging from 1.2 to 1.5 for methane and from 0.6 to 0.8 for the heaviest C7) fraction; kij of the methane/C7) heavy fraction varies from 0 to 0.3. The W corrections can be interpreted as modifications of the critical properties.75 With a somewhat untraditional regression approach, Coats and Smart minimize a sum of weighted absolute deviations using linear programming. They suggest weighting factors of 40 for saturation pressures, 10 for saturation densities, and 1 for most other data. Their results are impressive, showing excellent matches of nearcritical fluids, hydrocarbon and nonhydrocarbon gas injection in oils and retrograde condensate systems, and simple depletion data. With a two-constant cubic EOS with volume translation, the modifications of EOS parameters (or critical properties) is typically only 5 to 10% compared with the "30 to 40% modifications required with the Coats and Smart approach without volume translation. This is explained by the initial predictions being much better with vol19
ume translation, thereby requiring fewer modifications to achieve the same quality fit of measured data. Interestingly, the same five standard regression parameters originally suggested by Coats and Smart can be used with an EOS that uses volume translation. However, the result is usually that methane corrections to Wa and Wb remain close to 1.0 and corrections to Wa and Wb for the heaviest C7) fraction range from 0.9 to 1.1. Therefore, it may be better to drop methane corrections to Wa and Wb and use instead one set of corrections to the Wa and Wb for the heaviest C7) fraction, and another set of corrections to the Wa and Wb for the next-to-heaviest C7) fraction. This approach is particularly helpful when matching liquid-dropout curves with a “tail” (see Appendix C) or in multicontact vaporization experiments. Finally, an alternative to use of corrections to Wa and Wb directly would be to modify Tc and pc instead (modification of w is not recommended). Be aware, however, that the sensitivity of the minimization problem to Tc and pc is probably less than to Wa and Wb , thereby making the mathematical search for a minimum more difficult. Appendix C gives a thorough discussion of how nonlinear regression can be used to adjust EOS parameters systematically to fit measured PVT data. References 1. Edmister, W.C. and Lee, B.I.: Applied Hydrocarbon Thermodynamics, Gulf Publishing Co., Houston (1983). 2. Edmister, W.C. and Lee, B.I.: Applied Hydrocarbon Thermodynamics, second edition, Gulf Publishing Co., Houston (1984) I. 3. Reid, R.C., Prausnitz, J.M., and Polling, B.E.: The Properties of Gases and Liquids, fourth edition, McGraw-Hill Book Co. Inc., New York City (1987). 4. Michelsen, M.L.: “Partial Derivatives of Thermodynamic Properties from Equations of State,” report, Inst. for Kemiteknik, Denmark Technical U., Lyngby, Denmark (1981). 5. van der Waals, J.D.: Continuity of the Gaseous and Liquid State of Matter (1873). 6. Redlich, O. and Kwong, J.N.S.: “On the Thermodynamics of Solutions. V. An Equation of State. Fugacities of Gaseous Solutions,” Chem. Rev. (1949) 44, 233. 7. Peng, D.Y. and Robinson, D.B.: “A New-Constant Equation of State,” Ind. & Eng. Chem. (1976) 15, No. 1, 59. 8. Martin, J.J.: “Cubic Equations of State—Which?,” Ind. & Eng. Chem. (1979) 18, No. 2, 81. 9. Abbott, M.M.: “Cubic Equation of State,” AIChE J. (May 1973) 596. 10. Abbott, M.M.: “Cubic Equations of State: An Interpretive Review,” Equations of State in Engineering and Research, K.C. Chao and R.L. Robinson Jr. (eds.), Advances in Chemistry Series, Amer. Chemical Soc., Washington, DC (1978) 182, 47–97. 11. Yarborough, L.: “Application of a Generalized Equation of State to Petroleum Reservoir Fluids,” Equations of State in Engineering and Research, K.C. Chao and R.L. Robinson Jr. (eds.), Advances in Chemistry Series, Amer. Chemical Soc., Washington, DC (1978) 182, 386–439. 12. Usdin, E. and McAuliffe, J.C.: “A One Parameter Family of Equations of State,” Chem. Eng. Sci. (1976) 31, 1077. 13. Fuller, G.G.: “A Modified Redlich-Kwong-Soave Equation of State Capable of Representing the Liquid State,” Ind. & Eng. Chem. (1976) 15, 254. 14. Schmidt, G. and Wenzel, H.: “A Modified van der Waals Type Equation of State,” Chem. Eng. Sci. (1980) 35, 1503. 15. Patel, V.C. and Teja, A.S.: “A New Cubic Equation of State for Fluids and Fluid Mixtures,” Chem. Eng. Sci. (1982) 37, No. 3, 463. 16. Kumar, K.H. and Starling, K.E.: “Comments on: “Cubic Equations of State—Which?,” Ind. & Eng. Chem. (1979) 19, 128. 17. Kumar, K.H. and Starling, K.E.: “The Most General Density-Cubic Equation of State: Application to Pure Nonpolar Fluids,” Ind. & Eng. Chem. (1982) 21, 255. 18. Soave, G.: “Equilibrium Constants from a Modified Redlich-Kwong Equation of State,” Chem. Eng. Sci. (1972) 27, No. 6, 1197. 19. Zudkevitch, D. and Joffe, J.: “Correlation and Prediction of Vapor-Liquid Equilibrium with the Redlich-Kwong Equation of State,” AIChE J. (1970) 16, 112. 20. Peneloux, A., Rauzy, E., and Freze, R.: “A Consistent Correction for Redlich-Kwong-Soave Volumes,” Fluid Phase Equilibria (1982) 8, 7. 21. Martin, J.J. and Hou, Y.C.: AIChE J. (1955) 1, 142. 20
22. Abbott, M.M.: “Thirteen Ways of Looking at the van der Waals Equation,” paper #31b presented at the 1988 AIChE Spring Natl. Meeting, New Orleans, 7 March. 23. Michelsen, M.L.: “The Isothermal Flash Problem. Part II. Phase-Split Calculation,” Fluid Phase Equilibria (1982) 9, 21. 24. Nagy, Z. and Shirkovskiy, A.I: “Mathematical Simulation of Natural Gas Condensation Processes Using the Peng-Robinson Equation of State,” paper SPE 10982 presented at the 1982 SPE Annual Technical Conference and Exhibition, New Orleans, 26–29 September. 25. Robinson, D.B., Peng, D.Y., and Ng, H.-Y.: “Capabilities of the PengRobinson Programs, Part 2: Three-Phase and Hydrate Calculations,” Hydrocarbon Proc. (1979) 58, 269. 26. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “Characterization of Gas Condensate Mixtures,” C7) Fraction Characterization, L.G. Chorn and G.A. Mansoori (eds.), Advances in Thermodynamics, Taylor & Francis, New York City (1989) 1. 27. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “SRK-EOS Calculation for Crude Oils,” Fluid Phase Equilibria (1983) 14, 209. 28. Joffe, J., Schroeder, G.M., and Zudkevitch, D.: “Vapor-Liquid Equilibria with the Redlich-Kwong Equation of State,” AIChE J. (May 1970) 496. 29. Haman, S.E.M. et al.: “Generalized Temperature Dependent Parameters of the Redlich-Kwong Equation of State for Vapor-Liquid Equilibrium Calculations,” Ind. & Eng. Chem. Proc. Des. Dev. (1977) 16, No. 1. 30. Robinson, D.B. and Peng, D.Y.: “The Characterization of the Heptanes and Heavier Fractions,” Research Report 28, Gas Producers Assn., Tulsa, Oklahoma (1978). 31. Jhaveri, B.S. and Youngren, G.K.: “Three-Parameter Modification of the Peng-Robinson Equation of State To Improve Volumetric Predictions,” SPERE (August 1988) 1033. 32. Michelsen, M.L.: “The Isothermal Flash Problem. Part I. Stability,” Fluid Phase Equilibria (1982) 9, 1. 33. Nghiem, L.X. and Aziz, K.: “A Robust Iterative Method for Flash Calculations Using the Soave-Redlich-Kwong or the Peng-Robinson Equation of State,” paper SPE 8285 presented at the 1979 SPE Annual Technical Conference and Exhibition, Las Vegas, 23–26 September. 34. Trangenstein, J.A.: “Minimization of Gibbs Energy in Compositional Reservoir Simulation,” Chem. Eng. Sci. (1985) 12, 2847. 35. Rachford, H.H. and Rice, J.D.: “Procedure for Use of Electrical Digital Computers in Calculating Flash Vaporization Hydrocarbon Equilibrium,” JPT (October 1952) 19; Trans., AIME, 195. 36. Li, Y.-K. and Nmhiem, L.X.: “The Development of a General Phase Envelope Construction Algorithm for Reservoir Fluid Studies,” paper SPE 11198 presented at the 1982 SPE Annual Technical Conference and Exhibition, New Orleans, 26–29 September. 37. Whitson, C.H. and Michelsen, M.L.: “The Negative Flash,” Fluid Phase Equilibria (1989) 53, 51. 38. Muskat, M. and McDowell, J.M.: “An Electrical Computer for Solving Phase Equilibrium Problems,” Trans., AIME (1949) 186, 291. 39. Wilson, G.M.: “A Modified Redlich-Kwong Equation of State, Application to General Physical Data Calculations,” paper 15c presented at the 1969 AIChE Natl. Meeting, Cleveland, Ohio. 40. Mehra, R.K., Heidemann, R.A., and Aziz, K.: “Computation of Multiphase Equilibrium for Compositional Simulators,” paper SPE 9232 presented at the 1980 SPE Annual Technical Conference and Exhibition, Dallas, 21–24 September. 41. Mehra, R.K., Heidemann, R.A., and Aziz, K.: “Computation of Multiphase Equilibrium for Compositional Simulation,” SPEJ (February 1982) 61. 42. Nghiem, L.X.: “A New Approach to Quasi-Newton Method With Application to Compositional Modeling,” paper SPE 12242 presented at the 1983 SPE Symposium on Reservoir Simulation, San Francisco, 16–18 November. 43. Risnes, R., Dalen, V., and Jensen, J.I.: “Phase Equilibrium Calculations in the Near-Critical Region,” Proc., European Symposium on EOR, Bournemouth, U.K. (1981). 44. Crowe, A.M. and Nishio, M.: “Convergence Promotion in the Simulation of Chemical Processes-the General Dominant Eigenvalue Method,” AIChE J. (1975) 21, 528. 45. Young, L.: “Equation of State Compositional Modeling on Vector Processors,” JPT (February 1991) 107. 46. Baker, L.E., Pierce, A.C., and Luks, K.D.: “Gibbs Energy Analysis of Phase Equilibria,” SPEJ (October 1982) 731; Trans., AIME, 273. 47. Nghiem, L.X. and Li, Y.-K.: “Computation of Multiphase Equilibrium Phenomena With an Equation of State,” Fluid Phase Equilibria (1984) 17, 77. PHASE BEHAVIOR
48. Nghiem, L.X. and Li, Y.-K.: “Application of Tangent Plane Criterion to Saturation Pressure and Temperature Computations,” Fluid Phase Equilibria (1984) 21, 39. 49. Michelsen, M.L.: “Saturation Point Calculations,” Fluid Phase Equilibria (1985) 23, 181. 50. Michelsen, M.L.: “Calculation of Phase Envelopes and Critical Points for Multicomponent Mixtures,” Fluid Phase Equilibria (1980) 4, 1. 51. Michelsen, M.L.: “A Simple Method for Calculation of Approximate Phase Boundaries,” Fluid Phase Equilibria (1994) 98, 1. 52. Michelsen, M.L.: “Calculation of Critical Points and Phase Boundaries in the Critical Region,” Fluid Phase Equilibria (1984) 16, 57. 53. Gibbs, J.W.: The Collected Works of J. Willard Gibbs, Yale U. Press, New Haven, Connecticut (1948) 1. 54. Muskat, M.: “Distribution of Non-Reacting Fluids in the Gravitational Field,” Physical Rev. (June 1930) 35, 1384. 55. Sage, B.H. and Lacey, W.N.: “Gravitational Concentration Gradients in Static Columns of Hydrocarbon Fluids,” Trans., AIME (1938) 132, 120. 56. Schulte, A.M.: “Compositional Variations Within a Hydrocarbon Column Due to Gravity,” paper SPE 9235 presented at the 1980 SPE Annual Technical Conference and Exhibition, Dallas, 21–24 September. 57. Bath, P.G.H., Fowler, W.N., and Russell, M.P.M.: “The Brent Field, A Reservoir Engineering Review,” paper EUR 164 presented at the 1980 SPE European Offshore Petroleum Conference and Exhibition, London, 21–24 October. 58. Bath, P.G.H., van der Burgh, J., and Ypma, J.G.J.: “Enhanced Oil Recovery in the North Sea,” Proc., 11th World Pet. Cong. (1983). 59. Holt, T., Lindeberg, E., and Ratkje, S.K.: “The Effect of Gravity and Temperature Gradients on Methane Distribution in Oil Reservoirs,” paper SPE 11761 available from SPE, Richardson, Texas (1983). 60. Hirschberg, A.: “Role of Asphaltenes in Compositional Grading of a Reservoir’s Fluid Column,” JPT (January 1988) 89. 61. Riemens, W.G., Schulte, A.M., and de Jong, L.N.J.: “Birba Field PVT Variations Along the Hydrocarbon Column and Confirmatory Field Tests,” JPT (January 1988) 83. 62. Creek, J.L. and Schrader, M.L.: “East Painter Reservoir: An Example of a Compositional Gradient From a Gravitational Field,” paper SPE 14411 presented at the 1985 SPE Annual Technical Conference and Exhibition, Las Vegas, 22–25 September. 63. Metcalfe, R.S., Vogel, J.L., and Morris, R.W.: “Compositional Gradient in the Anschutz Ranch East Field,” paper SPE 14412 presented at the 1985 SPE Annual Technical Conference and Exhibition, Las Vegas, 22–25 September. 64. Montel, F. and Gouel, P.L.: “A New Lumping Scheme of Analytical Data for Compositional Studies,” paper SPE 13119 presented at the 1984 SPE Annual Technical Conference and Exhibition, Houston, 16–19 September. 65. Montel, F. and Gouel, P.L.: “Prediction of Compositional Grading in a Reservoir Fluid Column,” paper SPE 14410 presented at the 1985 SPE Annual Technical Conference and Exhibition, Las Vegas, 22–25 September. 66. Belery, P. and da Silva, F.V.: “Gravity and Thermal Diffusion in Hydrocarbon Reservoirs,” paper presented at the 1990 Chalk Research Program, Copenhagen, 11–12 June.
EQUATION-OF-STATE CALCULATIONS
67. Dougherty, E.L. Jr. and Drickamer, H.G.: “Thermal Diffusion and Molecular Motion in Liquids,” J. Phys. Chem. (1955) 59, 443. 68. Wheaton, R.J.: “Treatment of Variation of Composition With Depth in Gas-Condensate Reservoirs,” SPERE (May 1991) 239. 69. Chaback, J.J.: “Discussion of Treatment of Variations of Composition With Depth in Gas-Condensate Reservoirs,” SPERE (February 1992) 157. 70. Montel, F.: “Phase Equilibria Needs for Petroleum Exploration and Production Industry,” Fluid Phase Equilibria (1993) 84, 343. 71. Bedrikovetsky, P.G.: Mathematical Theory of Oil and Gas Recovery, Petroleum Engineering & Development Studies, Cluwer Academic, Horthreht, Russia (1993) 4. 72. Faissat, B. et al.: “Fundamental Statements about Thermal Diffusion for a Multicomponent Mixture in a Porous Medium,” Fluid Phase Equilibria (1995) 100, 1. 73. Whitson, C.H. and Belery, P.: “Compositional Gradients in Petroleum Reservoirs,” paper SPE 28000 presented at the 1994 U. of Tulsa/SPE Centennial Petroleum Engineering Symposium, Tulsa, Oklahoma, 29–31 August. 74. Coats, K.H. and Smart, G.T.: “Application of a Regression-Based EOS PVT Program to Laboratory Data,” SPERE (May 1986) 277. 75. Whitson, C.H.: “Effect of C7) Properties on Equation-of-State Predictions,” SPEJ (December 1984) 685; Trans., AIME, 277. 76. Coats, K.H.: “Simulation of Gas Condensate Reservoir Performance,” JPT (October 1985) 1870. 77. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “On the Dangers of Tuning Equation of State Parameters,” paper SPE 14487 available from SPE, Richardson, Texas (1985). 78. Agarwal, R., Li, Y.K., and Nghiem, L.X.: “A Regression Technique With Dynamic-Parameter Selection for Phase Behavior Matching,” SPERE (February 1990) 115. 79. Søreide, I.: “Improved Phase Behavior Predictions of Petroleum Reservoir Fluids From a Cubic Equation of State,” Dr.Ing. dissertion, Norwegian Inst. of Technology, Trondheim, Norway (1989). 80. Turek, E.A. et al.: “Phase Equilibria in CO2-Multicomponent Hydrocarbon Systems: Experimental Data and an Improved Prediction Technique,” SPEJ (June 1984) 308. 81. Zick, A.A.: “A Combined Condensing/Vaporizing Mechanism in the Displacement of Oil by Enriched Gases,” paper SPE 15493 presented at the 1986 SPE Annual Technical Conference and Exhibition, New Orleans, 5–8 October.
SI Metric Conversion Factors °API 141.5/(131.5)°API) +g/cm3 bar 1.0* E)05 +Pa ft 3.048* E*01 +m °F (°F*32)/1.8 +°C °F (°F)459.67)/1.8 +K psi 6.894 757 E)00 +kPa *Conversion factor is exact.
21
Chapter 5
HeptanesĆPlus Characterization 5.1 Introduction Some phase-behavior applications require the use of an equation of state (EOS) to predict properties of petroleum reservoir fluids. The critical properties, acentric factor, molecular weight, and binary-interaction parameters (BIP’s) of components in a mixture are required for EOS calculations. With existing chemical-separation techniques, we usually cannot identify the many hundreds and thousands of components found in reservoir fluids. Even if accurate separation were possible, the critical properties and other EOS parameters of compounds heavier than approximately C20 would not be known accurately. Practically speaking, we resolve this problem by making an approximate characterization of the heavier compounds with experimental and mathematical methods. The characterization of heptanesplus (C7)) fractions can be grouped into three main tasks.1–3 1. Dividing the C7) fraction into a number of fractions with known molar compositions. 2. Defining the molecular weight, specific gravity, and boiling point of each C7) fraction. 3. Estimating the critical properties and acentric factor of each C7) fraction and the key BIP’s for the specific EOS being used. This chapter presents methods for performing these tasks and gives guidelines on when each method can be used. A unique characterization does not exist for a given reservoir fluid. For example, different component properties are required for different EOS’s; therefore, the engineer must determine the quality of a given characterization by testing the predictions of reservoir-fluid behavior against measured pressure/volume/temperature (PVT) data. The amount of C7) typically found in reservoir fluids varies from u50 mol% for heavy oils to t1 mol% for light reservoir fluids.4 Average C7) properties also vary widely. For example, C7) molecular weight can vary from 110 to u300 and specific gravity from 0.7 to 1.0. Because the C7) fraction is a mixture of many hundreds of paraffinic, naphthenic, aromatic, and other organic compounds,5 the C7) fraction cannot be resolved into its individual components with any precision. We must therefore resort to approximate descriptions of the C7) fraction. Sec. 5.2 discusses experimental methods available for quantifying C7) into discrete fractions. True-boiling-point (TBP) distillation provides the necessary data for complete C7) characterization, including mass and molar quantities, and the key inspection data for each fraction (specific gravity, molecular weight, and boiling point). Gas chromatography (GC) is a less-expensive, time-saving alternative to TBP distillation. However, GC analysis quantifies only the mass of C7) fractions; such properties as specific gravity and boiling point are not provided by GC analysis. HEPTANES-PLUS CHARACTERIZATION
Typically, the practicing engineer is faced with how to characterize a C7) fraction when only z C7) the mole fraction, ; molecular weight, M C7); and specific gravity, g C7) , are known. Sec. 5.3 reviews methods for splitting C7) into an arbitrary number of subfractions. Most methods assume that mole fraction decreases exponentially as a function of molecular weight or carbon number. A more general model based on the gamma distribution has been successfully applied to many oil and gas-condensate systems. Other splitting schemes can also be found in the literature; we summarize the available methods. Sec. 5.4 discusses how to estimate inspection properties g and Tb for C7) fractions determined by GC analysis or calculated from a mathematical split. Katz and Firoozabadi’s6 generalized single carbon number (SCN) properties are widely used. Other methods for estimating specific gravities of C7) subfractions are based on forcing the calculated g C7) to match the measured value. Many empirical correlations are available for estimating critical properties of pure compounds and C7) fractions. Critical properties can also be estimated by forcing the EOS to match the boiling point and specific gravity of each C7) fraction separately. In Sec. 5.5, we review the most commonly used methods for estimating critical properties. Finally, Sec. 5.6 discusses methods for reducing the number of components describing a reservoir mixture and, in particular, the C7) fraction. Splitting the C7) into pseudocomponents is particularly important for EOS-based compositional reservoir simulation. A large part of the computing time during a compositional reservoir simulation is used to solve the flash calculations; accordingly, minimizing the number of components without jeopardizing the quality of the fluid characterization is necessary. 5.2 Experimental Analyses The most reliable basis for C7) characterization is experimental data obtained from high-temperature distillation or GC. Many experimental procedures are available for performing these analyses; in the following discussion, we review the most commonly used methods. TBP distillation provides the key data for C7) characterization, including mass and molar quantities, specific gravity, molecular weight, and boiling point of each distillation cut. Other such inspection data as kinematic viscosity and refractive index also may be measured on distillation cuts. Simulated distillation by GC requires smaller samples and less time than TBP distillation.7-9 However, GC analysis measures only the mass of carbon-number fractions. Simulated distillation results can be calibrated against TBP data, thus providing physical properties for the individual fractions. For many oils, simulated distillation 1
Cutoff (n-paraffin) boiling point Midvolume (“normal”) boiling point
Dp
Dp
N2
N2
Fig. 5.2—TBP curve for a North Sea gas-condensate sample illustrating the midvolume-point method for calculating average boiling point (after Austad et al.7).
Fig. 5.1—Standard apparatus for conducting TBP analysis of crude-oil and condensate samples at atmospheric and subatmospheric pressures (after Ref. 11).
provides the necessary information for C7) characterization in far less the time and at far less cost than that required for a complete TBP analysis. We recommend, however, that at least one complete TBP analysis be measured for (1) oil reservoirs that may be candidates for gas injection and (2) most gas-condensate reservoirs. 5.2.1 TBP Distillation. In TBP distillation, a stock-tank liquid (oil or condensate) is separated into fractions or “cuts” by boiling-point range. TBP distillation differs from the Hempel and American Soc. for Testing Materials (ASTM) D-158 distillations10 because TBP analysis requires a high degree of separation, which is usually controlled by the number of theoretical trays in the apparatus and the reflux ratio. TBP fractions are often treated as components having unique boiling points, critical temperatures, critical pressures, and other properties identified for pure compounds. This treatment is obviously more valid for a cut with a narrow boiling-point range. The ASTM D-289211 procedure is a useful standard for TBP analysis of stock-tank liquids. ASTM D-2892 specifies the general procedure for TBP distillation, including equipment specifications (see Fig. 5.1), reflux ratio, sample size, and calculations necessary to arrive at a plot of cumulative volume percent vs. normal boiling point. Normal boiling point implies that boiling point is measured at normal or atmospheric pressure. In practice, to avoid thermal decomposition (cracking), distillation starts at atmospheric pressure and is changed to subatmospheric distillation after reaching a limiting temperature. Subatmospheric boiling-point temperatures are converted to normal boiling-point temperatures by use of a vaporpressure correlation that corrects for the amount of vacuum and the fraction’s chemical composition. The boiling-point range for fractions is not specified in the ASTM standard. Katz and Firoozabadi6 recommend use of paraffin normal boiling points (plus 0.5°C) as boundaries, a practice that has been widely accepted. 2
Fig. 5.27 shows a plot of typical TBP data for a North Sea sample. Normal boiling point is plotted vs. cumulative volume percent. Table 5.1 gives the data, including measured specific gravities and molecular weights. Average boiling point is usually taken as the value found at the midvolume percent of a cut. For example, the third cut in Table 5.1 boils from 258.8 to 303.8°F, with an initial 27.49 vol% and a final 37.56 vol%. The midvolume percent is (27.49)37.56)/2+32.5 vol%; from Fig. 5.2, the boiling point at this volume is [282°F. For normal-paraffin boiling-point intervals, Katz and Firoozabadi’s6 average boiling points of SCN fractions can be used (see Table 5.2). The mass, m i, of each distillation cut is measured directly during a TBP analysis. The cut is quantified in moles n i with molecular weight, M i, and the measured mass m i, where n i + m ińM i. Volume of the fraction is calculated from the mass and the density, ò i (or specific gravity, g i), where V i + m ińò i . M i is measured by a cryoscopic method based on freezing-point depression, and ò i is measured by a pycnometer or electronic densitometer. Table 5.1 gives cumulative weight, mole, and volume percents for the North Sea sample. Average C7) properties are given by
ȍm N
MC
7)
+
i
i+1 N
ȍn
i
i+1
ȍm N
and ò C
7)
+
i
i+1 N
ȍV
,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.1)
i
i+1
where ò C7) + g C7)ò w with ò w +pure water density at standard conditions. These calculated averages are compared with measured values of the C7) sample, and discrepancies are reported as “lost” material. Refs. 7 and 15 through 20 give procedures for calculating properties from TBP analyses. Also, the ASTM D-289211 procedure gives details on experimental equipment and the procedure for conducting TBP analysis at atmospheric and subatmospheric conditions. Table 5.3 gives an example TBP analysis from a commercial laboratory. PHASE BEHAVIOR
TABLE 5.1—EXPERIMENTAL TBP RESULTS FOR A NORTH SEA CONDENSATE Upper Tbi (°F)
Average Tbi * (°F)
C7
208.4
194.0
90.2
0.7283
96
123.9
0.940
C8
258.8
235.4
214.6
0.7459
110
287.7
C9
303.8
282.2
225.3
0.7658
122
C10
347.0
325.4
199.3
0.7711
C11
381.2
363.2
128.8
C12
420.8
401.1
C13
455.0
C14
4.35
4.80
7.80
4.35
4.80
11.92
1.951
10.35
11.15
16.19
14.70
15.95
11.88
294.2
1.847
10.87
11.40
15.33
25.57
27.35
11.82
137
258.5
1.455
9.61
10.02
12.07
35.18
37.37
11.96
0.7830
151
164.5
0.853
6.21
6.37
7.08
41.40
43.74
11.97
136.8
0.7909
161
173.0
0.850
6.60
6.70
7.05
48.00
50.44
12.03
438.8
123.8
0.8047
181
153.8
0.684
5.97
5.96
5.68
53.97
56.41
11.99
492.8
474.8
120.5
0.8221
193
146.6
0.624
5.81
5.68
5.18
59.78
62.09
11.89
C15
523.4
509.0
101.6
0.8236
212
123.4
0.479
4.90
4.78
3.98
64.68
66.87
12.01
C16
550.4
537.8
74.1
0.8278
230
89.5
0.322
3.57
3.47
2.67
68.26
70.33
12.07
C17
579.2
564.8
76.8
0.8290
245
92.6
0.313
3.70
3.59
2.60
71.96
73.92
12.16
C18
604.4
591.8
58.2
0.8378
259
69.5
0.225
2.81
2.69
1.87
74.77
76.62
12.14
C19
629.6
617.0
50.2
0.8466
266
59.3
0.189
2.42
2.30
1.57
77.19
78.91
12.11
C20
653.0
642.2
45.3
0.8536
280
53.1
0.162
2.19
2.06
1.34
79.37
80.97
12.10
427.6
0.8708
370
491.1
1.156
20.63
19.03
9.59
100.00
100.00
2,580.5
12.049
100.00
100.00
100.00
Sum
Mi (g/mol)
gi **
2,073.1
Average
0.8034
Vi (cm3)
ni (mol)
wi (%)
SxVi %
xi %
C21)
mi (g)
Swi %
xVi %
Fraction
172
Kw
11.98
Reflux ratio+1 : 5; reflux cycle+18 seconds; distillation at atmospheric pressure+201.2 to 347°F; distillation at 100 mm Hg+347 to 471.2°F; and distillation at 10 mm Hg+471.2 to 653°F. Vi +mi /gi /0.9991; ni +mi /Mi ; wi +100 *Average taken at midvolume point. **Water+1.
mi /2073.1; xVi +100
Vi/2580.5; xi +100
ni /12.049; Swi +Swi ; SxVi +SxVi ; and Kw +(Tbi +460)1/3/gi .
Boiling points are not reported because normal-paraffin boiling-point intervals are used as a standard; accordingly, the average boiling points suggested by Katz and Firoozabadi6 (Table 5.2) can be used. 5.2.2 Chromatography. GC and, to a lesser extent, liquid chromatography are used to quantify the relative amount of compounds found in oil and gas systems. The most important application of chromatography to C7) characterization is simulated distillation by GC techniques. Fig. 5.3 shows an example gas chromatogram for the North Sea sample considered earlier. The dominant peaks are for normal paraffins, which are identified up to n-C22. As a good approximation for a paraffinic sample, the GC response for carbon number Ci starts at the bottom response of n-Ci*1 and extends to the bottom response of n-Ci . The mass of carbon number Ci is calculated as the area under the curve from the baseline to the GC response in the n-Ci*1 to n-Ci interval (see the shaded area for fraction C9 in Fig. 5.3). As Fig. 5.47 shows schematically, the baseline should be determined before running the actual chromatogram. Because stock-tank samples cannot be separated completely by standard GC analysis, an internal standard must be used to relate GC area to mass fraction. Normal hexane was used as an internal standard for the sample in Fig. 5.3. The internal standard’s response factor may need to be adjusted to achieve consistency between simulated and TBP distillation results. This factor will probably be constant for a given oil, and the factor should be determined on the basis of TBP analysis of at least one sample from a given field. Fig. 5.5 shows the simulated vs. TBP distillation curves for the Austad et al.7 sample. A 15% correction to the internal-standard response factor was used to match the two distillation curves. As an alternative to correcting the internal standard, Maddox and Erbar15 suggest that the reported chromatographic boiling points be adjusted by a correction factor that depends on the reported boiling HEPTANES-PLUS CHARACTERIZATION
point and the “paraffinicity” of the composite sample. This correction factor varies from 1 to 1.15 and is slightly larger for aromatic than paraffinic samples. Several laboratories have calibrated GC analysis to provide simulated-distillation results up to C40. However, checking the accuracy of simulated distillation for SCN fractions greater than approximately C25 is difficult because C25 is usually the upper limit for reliable TBP distillation. The main disadvantage of simulated distillation is that inspection data are not determined directly for each fraction and must therefore either be correlated from TBP data or estimated from correlations (see Sec. 5.4). Sophisticated analytical methods, such as mass spectroscopy, may provide detailed information on the compounds separated by GC. For example, mass spectroscopy GC can establish the relative amounts of paraffins, naphthenes, and aromatics (PNA’s) for carbon-number fractions distilled by TBP analysis. Detailed PNA information should provide more accurate estimation of the critical properties of petroleum fractions, but the analysis is relatively costly and time-consuming from a practical point of view. Recent work has shown that PNA analysis3,19-23 may improve C7) characterization for modeling phase behavior with EOS’s. Our experience, however, is that PNA data have limited usefulness for improving EOS fluid characterizations. 5.3 Molar Distribution Molar distribution is usually thought of as the relation between mole fraction and molecular weight. In fact, this concept is misleading because a unique relation does not exist between molecular weight and mole fraction unless the fractions are separated in a consistent manner. Consider for example a C7) sample distilled into 10 cuts separated by normal-paraffin boiling points. If the same C7) sample is distilled with constant 10-vol% cuts, the two sets of data will not 3
TABLE 5.2—SINGLE CARBON NUMBER PROPERTIES FOR HEPTANES-PLUS (after Katz and Firoozabadi6) Katz-Firoozabadi Generalized Properties Lee-Kesler12/Kesler-Lee13 Correlations
Tb Interval* Fraction Number
Defined Kw
Tc (°R)
pc (psia)
ą ąw
Riazi14
Defined
Vc (ft3/lbm mol)
Zc
Lower (°F)
Upper (°F)
Average Tb (°F) (°R)
ăăg*ă
M
6
97.7
156.7
147.0
606.7
0.690
84
12.27
914
476
0.271
5.6
0.273
7
156.7
210.0
197.4
657.1
0.727
96
11.96
976
457
0.310
6.2
0.272
8
210.0
259.0
242.1
701.7
0.749
107
11.86
1,027
428
0.349
6.9
0.269
9
259.0
304.3
288.0
747.6
0.768
121
11.82
1,077
397
0.392
7.7
0.266
10
304.3
346.3
330.4
790.1
0.782
134
11.82
1,120
367
0.437
8.6
0.262
11
346.3
385.5
369.0
828.6
0.793
147
11.84
1,158
341
0.479
9.4
0.257
12
385.5
422.2
406.9
866.6
0.804
161
11.86
1,195
318
0.523
10.2
0.253
13
422.2
456.6
441.0
900.6
0.815
175
11.85
1,228
301
0.561
10.9
0.249
14
456.6
489.0
475.5
935.2
0.826
190
11.84
1,261
284
0.601
11.7
0.245
15
489.0
520.0
510.8
970.5
0.836
206
11.84
1,294
268
0.644
12.5
0.241
16
520.0
548.6
541.4
1,001.1
0.843
222
11.87
1,321
253
0.684
13.3
0.236
17
548.6
577.4
572.0
1,031.7
0.851
237
11.87
1,349
240
0.723
14.0
0.232
18
577.4
602.6
595.4
1,055.1
0.856
251
11.89
1,369
230
0.754
14.6
0.229
19
602.6
627.8
617.0
1,076.7
0.861
263
11.90
1,388
221
0.784
15.2
0.226
20
627.8
651.2
640.4
1,100.1
0.866
275
11.92
1,408
212
0.816
15.9
0.222
21
651.2
674.6
663.8
1,123.5
0.871
291
11.94
1,428
203
0.849
16.5
0.219
22
674.6
692.6
685.4
1,145.1
0.876
305
11.94
1,447
195
0.879
17.1
0.215
23
692.6
717.8
707.0
1,166.7
0.881
318
11.95
1,466
188
0.909
17.7
0.212
24
717.8
737.6
726.8
1,186.5
0.885
331
11.96
1,482
182
0.936
18.3
0.209
25
737.6
755.6
746.6
1,206.3
0.888
345
11.99
1,498
175
0.965
18.9
0.206
26
755.6
775.4
766.4
1,226.1
0.892
359
12.00
1,515
168
0.992
19.5
0.203
27
775.4
793.4
786.2
1,245.9
0.896
374
12.01
1,531
163
1.019
20.1
0.199
28
793.4
809.6
804.2
1,263.9
0.899
388
12.03
1,545
157
1.044
20.7
0.196
29
809.6
825.8
820.4
1,280.1
0.902
402
12.04
1,559
152
1.065
21.3
0.194
30
825.8
842.0
834.8
1,294.5
0.905
416
12.04
1,571
149
1.084
21.7
0.191
31
842.0
858.2
851.0
1,310.7
0.909
430
12.04
1,584
145
1.104
22.2
0.189
32
858.2
874.4
865.4
1,325.1
0.912
444
12.04
1,596
141
1.122
22.7
0.187
33
874.4
888.8
879.8
1,339.5
0.915
458
12.05
1,608
138
1.141
23.1
0.185
34
888.8
901.4
892.4
1,352.1
0.917
472
12.06
1,618
135
1.157
23.5
0.183
35
901.4
915.8
906.8
1,366.5
0.920
486
12.06
1,630
131
1.175
24.0
0.180
36
919.4
1,379.1
0.922
500
12.07
1,640
128
1.192
24.5
0.178
37
932.0
1,391.7
0.925
514
12.07
1,650
126
1.207
24.9
0.176
38
946.4
1,406.1
0.927
528
12.09
1,661
122
1.226
25.4
0.174
39
959.0
1,418.7
0.929
542
12.10
1,671
119
1.242
25.8
0.172
40
971.6
1,431.3
0.931
556
12.10
1,681
116
1.258
26.3
0.170
41
982.4
1,442.1
0.933
570
12.11
1,690
114
1.272
26.7
0.168
42
993.2
1,452.9
0.934
584
12.13
1,697
112
1.287
27.1
0.166
43
1,004.0
1,463.7
0.936
598
12.13
1,706
109
1.300
27.5
0.164
44
1,016.6
1,476.3
0.938
612
12.14
1,716
107
1.316
27.9
0.162
45
1,027.4
1,487.1
0.940
626
12.14
1,724
105
1.328
28.3
0.160
*At 1 atmosphere. **Water+1.
produce the same plot of mole fraction vs. molecular weight. However, a plot of cumulative mole fraction,
ȍz
vs. cumulative average molecular weight,
ȍz M
i
Q zi +
j+1
ȍz
j
,ĂĂ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.2)
N
j+1
4
i
j
j
Q Mi +
j+1
ȍz
j
,
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.3)
j
j+1
PHASE BEHAVIOR
TABLE 5.3—STANDARD TBP RESULTS FROM COMMERCIAL PVT LABORATORY Component
mol%
wt%
Density (g/cm3)
Gravity ągAPI
Molecular Weight
Heptanes Octanes Nonanes Decanes Undecanes Dodecanes Tridecanes Tetradecanes Pentadecanes plus
1.12 1.30 1.18 0.98 0.62 0.57 0.74 0.53 4.10
2.52 3.08 3.15 2.96 2.10 2.18 3.05 2.39 31.61
0.7258 0.7470 0.7654 0.7751 0.7808 0.7971 0.8105 0.8235 0.8736
63.2 57.7 53.1 50.9 49.5 45.8 42.9 40.1 30.3
96 101 114 129 144 163 177 192 330
*At 60°F. Note: Katz and Firoozabadi6 average boiling points (Table 5.2) can be used when normal paraffin boiling-point intervals are used.
should produce a single curve. Strictly speaking, therefore, molar distribution is the relation between cumulative molar quantity and some expression for cumulative molecular weight. In this section, we review methods commonly used to describe molar distribution. Some methods use a consistent separation of fractions (e.g., by SCN) so the molar distribution can be expressed directly as a relationship between mole fraction and molecular weight of individual cuts. Most methods in this category assume that C7) mole fractions decrease exponentially. A more general approach uses the continuous three-parameter gamma probability function to describe molar distribution. 5.3.1 Exponential Distributions. The Lohrenz-Bray-Clark24 (LBC) viscosity correlation is one of the earliest attempts to use an exponential-type distribution for splitting C7). The LBC method splits C7) into normal paraffins C7 though C40 with the relation z i + z C exp[A 1(i * 6) ) A 2(i * 6) 2], . . . . . . . . . . . . . (5.4) 6
where i+carbon number and z C6 +measured C6 mole fraction. Constants A1 and A2 are determined by trial and error so that
ȍz
7)
7)
+
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.5)
MC
7)
+
i
i
. . . . . . . . . . . . . . . . . . . . . . . . (5.6)
i+7
are satisfied. Paraffin molecular weights (Mi +14i)2) are used in Eq. 5.6. A Newton-Raphson algorithm can be used to solve Eqs. 5.5 and 5.6. Note that the LBC model cannot be used when z C7) t z C6 and M C7) u M C40. The LBC form of the exponential distribution has not found widespread application. More commonly, a linear form of the exponential distribution is used to split the C7) fraction. Writing the exponential distribution in a general form for any Cn) fraction (n+7 being a special case), z i + z Cn exp A[(i * n)],
. . . . . . . . . . . . . . . . . . . . . . . . (5.7)
where i+carbon number, z Cn +mole fraction of Cn , and A+constant indicating the slope on a plot of ln z i vs. i. The constants z Cn and A can be determined explicitly. With the general expression M i + 14 i ) h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.8) for molecular weight of Ci and the assumption that the distribution is infinite, constants z Cn and A are given by
40
zC
ȍz M 40
and z C
z Cn +
i+7
14 M Cn) * 14(n * 1) * h
and A + lnǒ1 * z CnǓ
. . . . . . . . . . . . . . . . . . (5.9)
. . . . . . . . . . . . . . . . . . . . . . . . . . . (5.10)
R
so that
ȍz + 1 i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.11)
i+n
(a)
(b)
(c)
Fig. 5.3—Simulated distillation by GC of the North Sea gas-condensate sample in Fig. 5.2 (after Austad et al.7). HEPTANES-PLUS CHARACTERIZATION
Fig. 5.4—GC simulated distillation chromatograms (a) without any sample (used to determine the baseline), (b) for a crude oil, and (c) for a crude oil with internal standard (after MacAllister and DeRuiter9). 5
700 to 1,000°F Distillate
1,000 to 1,250°F Distillate
1,200°F Residue
Fig. 5.5—Comparison of TBP and GC-simulated distillation for a North Sea gas-condensate sample (after Austad et al.7). R
and
ȍz M + M i
i
C n)
. . . . . . . . . . . . . . . . . . . . . . . . . . . (5.12)
i+n
are satisfied. Eqs. 5.9 and 5.10 imply that once a molecular weight relation is chosen (i.e., h is fixed), the distribution is uniquely defined by C7) molecular weight. Realistically, all reservoir fluids having a given C7) molecular weight will not have the same molar distribution, which is one reason why more complicated models have been proposed. 5.3.2 Gamma-Distribution Model. The three-parameter gamma distribution is a more general model for describing molar distribution. Whitson2,25,26 and Whitson et al.27 discuss the gamma distribution and its application to molar distribution. They give results for 44 oil and condensate C7) samples that were fit by the gamma distribution with data from complete TBP analyses. The absolute average deviation in estimated cut molecular weight was 2.5 amu (molecular weight units) for the 44 samples. The gamma probability density function is p(M) +
(M * h) a*1 exp NJ* ƪǒ M * h ǓńbƫNj b a G(a)
, . . . . . . . . (5.13)
where G+gamma function and b is given by b+
MC
7)
a
*h
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.14)
The three parameters in the gamma distribution are a, h, and M C7) The key parameter a defines the form of the distribution, and its value usually ranges from 0.5 to 2.5 for reservoir fluids; a+1 gives an exponential distribution. Application of the gamma distribution to heavy oils, bitumen, and petroleum residues indicates that the upper limit for a is 25 to 30, which statistically is approaching a log-normal distribution (see Fig. 5.628). The parameter h can be physically interpreted as the minimum molecular weight found in the C7) fraction. An approximate relation between a and h is 110 h[ . . . . . . . . . . . . . . . . . . . . . . . . . (5.15) 1 * ǒ1 ) 4 ńa 0.7Ǔ 6
Fig. 5.6—Gamma distributions for petroleum residue (after Brulé et al.28).
for reservoir-fluid C7) fractions. Practically, h should be considered as a mathematical constant more than as a physical property, either calculated from Eq. 5.15 or determined by fitting measured TBP data. Fig. 5.7 shows the function p(M) for the Hoffman et al.29 oil and a North Sea oil. Parameters for these two oils were determined by fitting experimental TBP data. The Hoffman et al. oil has a relatively large a of 2.27, a relatively small h of 75.7, with M C7)+198; the North Sea oil is described by a+0.82, h+93.2, and M C7)+227. The continuous distribution p(M ) is applied to petroleum fractions by dividing the area under the p(M ) curve into sections (shown schematically in Fig. 5.8). By definition, total area under the p(M ) curve from h to R is unity. The area of a section is defined as normalized mole fraction z ińz C 7) for the range of molecular weights Mbi*1 to Mbi . If the area from h to molecular-weight boundary Mb is defined as P0(Mb ), then the area of Section i is P0(Mbi )*P0(Mbi*1), also shown schematically in Fig. 5.8. Mole fraction zi can be written zi + zC
7)
ƪP ǒM Ǔ * P ǒM Ǔƫ . 0
bi
0
b i*1
. . . . . . . . . . . . . . . (5.16)
Average molecular weight in the same interval is given by Mi + h ) a b
P 1ǒM b iǓ * P 1ǒM b i*1Ǔ P 0ǒM b iǓ * P 0ǒM b i*1Ǔ
,
. . . . . . . . . . . (5.17)
where P 0 + Q S, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.18)
ǒ
Ǔ
1 , . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.19) and P 1 + Q S * a PHASE BEHAVIOR
The gamma distribution can be fit to experimental molar-distribution data by use of a nonlinear least-squares algorithm to determine a, h, and b. Experimental TBP data are required, including weight fraction and molecular weight for at least five C7) fractions (use of more than 10 fractions is recommended to ensure a unique fit of model parameters). The sum-of-squares function can be defined as
a + 2.273 h + 75.7 M C + 198.4 7)
a + 0.817 h + 93.2 M C + 227
Fǒ a, h , b Ǔ +
7)
ȍ (D
N*1
Mi)
2
,
. . . . . . . . . . . . . . . . . . . . . . . (5.24)
i+1
where D Mi +
Fig. 5.7—Gamma density function for the Hoffman et al.29 oil (dashed line) and a North Sea volatile oil (solid line). After Whitson et al.27
where Q + e *y y a G(a), . . . . . . . . . . . . . . . . . . . . . . . . . (5.20) R
S+
ƪ
ȍ y Ȋ(a ) k) j
j
j+0
and y +
k+0
ƫ
,
. . . . . . . . . . . . . . . . . . . (5.21)
i
. . . . . . . . . . . . . . . . . . (5.25)
ȍw , i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.26)
j+1
vs. the cumulative dimensionless molecular-weight variable,
8
i
.
Subscripts mod and exp+model and experimental, respectively. This sum-of-squares function weights the lower molecular weights more than higher molecular weights, in accordance with the expected accuracy for measurement of molecular weight. Also, the sum-of-squares function does not include the last molecular weight because this molecular weight may be inaccurate or backcalculated to match the measured average C7) molecular weight. If the last fraction is not included, the model average molecular weight, (M C7)) mod + h ) ab, can be compared with the experimental value as an independent check of the fit. A simple graphical procedure can be used to fit parameters a and h if experimental M C7) is fixed and used to define b. Fig. 5.10 shows a plot of cumulative weight fraction, Q wi +
Note that P0(Mb0+h)+P1(Mb0+h)+0. The summation in Eq. 5.21 should be performed until the last term is t1 10*8. The gamma function can be estimated by30
ȍA x
(M i) exp
i
*1
Mb * h . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.22) b
Gǒ x ) 1Ǔ + 1 )
(M i) mod * (M i) exp
, . . . . . . . . . . . . . . . . . . . . . (5.23)
i+1
where A1+*0.577191652, A2+0.988205891, A3+*0.897056937, A4+0.918206857, A5+*0.756704078, A6+0.482199394, A7+ *0.193527818, and A8+0.035868343 for 0xxx1. The recurrence formula, G(x)1)+xG(x), is used for xu1 and xt1; furthermore, G(1)+1. The equations for calculating zi and Mi are summarized in a short FORTRAN program GAMSPL found in Appendix A. In this simple program, the boundary molecular weights are chosen arbitrarily at increments of 14 for the first 19 fractions, starting with h as the first lower boundary. The last fraction is calculated by setting the upper molecular-weight boundary equal to 10,000. Table 5.4 gives three sample outputs from GAMSPL for a+0.5, 1, and 2 with h+90 and M C7)+200 held constant. Fig. 5.9 plots the results as log zi vs. Mi . The amount and molecular weight of the C26) fraction varies for each value of a.
Q *M i +
QM i * h . MC * h
. . . . . . . . . . . . . . . . . . . . . . . . . . . (5.27)
7)
Table 5.5 and the following outline describe the procedure for determining model parameters with Fig. 5.10 and TBP data. 1. Tabulate measured mole fractions zi and molecular weights Mi for each fraction. 2. Calculate experimental weight fractions, w i + (z i M i) B (z C 7)M C7)), if they are not reported. 3. Normalize weight fractions and calculate cumulative normalized weight fraction Q w i . 4. Calculate cumulative molecular weight Q M i from Eq. 5.3. 5. Assume several values of h (e.g., from 75 to 100) and calculate Q *M i for each value of the estimated h. 6. For each estimate of h, plot Q *M i vs. Q wi on a copy of Fig. 5.10 and choose the curve that fits one of the model curves best. Read the value of a from Fig. 5.10. 7. Calculate molecular weights and mole fractions of Fractions i using the best-fit curve in Fig. 5.10. Enter the curve at measured values of Q wi , read Q *M i , and calculate Mi from Mi + h ) ǒMC
7)
* hǓ
ƪǒ
Q wi * Q wi*1
Ǔ * ǒQ wi*1ńQ *M i*1Ǔƫ
Q wińQ *M i
.
. . . . . . . . . . . . . . . . . . . (5.28)
p(M)
h
A + z ińz C 7)
+ P 0ǒM biǓ * P 0ǒM bi*1Ǔ
h M bi A + P 0ǒM biǓ
h M bi*1 A + P 0ǒM bi*1Ǔ
Fig. 5.8—Schematic showing the graphical interpretation of areas under the gamma density function p(M) that are proportional to normalized mole fraction; A+area. HEPTANES-PLUS CHARACTERIZATION
7
TABLE 5.4—RESULTS OF GAMSPL PROGRAM FOR THREE DATA SETS WITH DIFFERENT GAMMA-DISTRIBUTION PARAMETER a ăąąąăa+0.5
ăąąąăa+1.0
Mole
Molecular
Mole
Molecular
Mole
Molecular
Number
Fraction
Weight
Fraction
Weight
Fraction
Weight
1
0.2787233
94.588
0.1195065
96.852
0.0273900
99.132
2
0.1073842
110.525
0.1052247
110.852
0.0655834
111.490
3
0.0772607
124.690
0.0926497
124.852
0.0852269
125.172
4
0.0610991
138.758
0.0815774
138.852
0.0927292
139.038
5
0.0505020
152.796
0.0718284
152.852
0.0925552
152.963
6
0.0428377
166.819
0.0632444
166.852
0.0877762
166.916
7
0.0369618
180.836
0.0556863
180.852
0.0804707
180.883
8
0.0322804
194.848
0.0490314
194.852
0.0720157
194.859
9
0.0284480
208.857
0.0431719
208.852
0.0632969
208.841
10
0.0252470
222.864
0.0380125
222.852
0.0548597
222.826
11
0.0225321
236.870
0.0334698
236.852
0.0470180
236.814
12
0.0202013
250.875
0.0294699
250.852
0.0399302
250.805
13
0.0181808
264.879
0.0259481
264.852
0.0336535
264.797
14
0.0164152
278.883
0.0228471
278.852
0.0281813
278.790
15
0.0148619
292.886
0.0201167
292.852
0.0234690
292.784
16
0.0134879
306.888
0.0177127
306.852
0.0194514
306.778
17
0.0122665
320.890
0.0155959
320.852
0.0160543
320.774
18
0.0111762
334.892
0.0137321
334.852
0.0132017
334.770
19
0.0101996
348.894
0.0120910
348.852
0.0108204
348.766
0.1199341
539.651
0.0890834
466.000
0.0463166
420.424
20 Total
1.0000000
1.0000000
Average
200
For all three cases h + 90 and M C
+ 200.
7)
ǒ
Qw i Q *M i
*
Q w i*1 Q *M i*1
Ǔ
.
. . . . . . . . . . . . . . . . . . . (5.29)
+ 200
(
}
7)
h + 90 DM b + 14
0.8 (
V a + 2.0
MC
1.0
)
a + 0.5 a + 1.0
200
Fig. 5.11 shows a Q *M i * Q wi match for the Hoffman et al.29 oil with h+70, 72.5, 75, and 80 and indicates that a best fit is achieved for h+72.5 and a+2.5 (see Fig. 5.12). Although the gamma-distribution model has the flexibility of treating reservoir fluids from light condensates to bitumen, most reservoir fluids can be characterized with an exponential molar distribution (a+1) without adversely affecting the quality of EOS pre)
For computer applications, Q wi and Q *M i can be calculated exactly from Eqs. 5.16 through 5.23 with little extra effort.
f
1.0000000 200
Mole fractions zi are given by z i + z C 7)
ăąąąăa+2.0
Fraction
0.6
0.4
0.2
0.0 0.0
0.2
0.4
0.6
0.8
1.0
Cumulative Normalized Mole Fraction, Qzi
Fig. 5.9—Three example molar distributions for an oil sample with M C 7)= 200 and h = 90, calculated with the GAMSPL program (Table A-4) in Table 5.4. 8
Fig. 5.10—Cumulative-distribution type curve for fitting experimental TBP data to the gamma-distribution model. Parameters a and h are determined with M C held constant. 7)
PHASE BEHAVIOR
TABLE 5.5—CALCULATION OF CUMULATIVE WEIGHT FRACTION AND CUMULATIVE MOLECULAR WEIGHT VARIABLE FOR HOFFMAN et al.29 OIL Q *Mi Component i
zi
ąSzi ą
Mi
zi Mi
ăSzi Mi ă
Qwi
QMi
h+70
h+72.5
h+75
h+80
h+85
7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
0.0263 0.0234 0.0235 0.0224 0.0241 0.0246 0.0266 0.0326 0.0363 0.0229 0.0171 0.0143 0.0130 0.0108 0.0087 0.0072 0.0058 0.0048 0.0039 0.0034 0.0028 0.0025 0.0023 0.0091
0.0263 0.0497 0.0732 0.0956 0.1197 0.1443 0.1709 0.2035 0.2398 0.2627 0.2799 0.2941 0.3072 0.3180 0.3267 0.3338 0.3396 0.3444 0.3483 0.3517 0.3545 0.3570 0.3593 0.3684
99 110 121 132 145 158 172 186 203 222 238 252 266 279 290 301 315 329 343 357 371 385 399 444
2.604 2.574 2.844 2.957 3.497 3.882 4.570 6.067 7.371 5.093 4.079 3.596 3.466 3.008 2.526 2.152 1.811 1.582 1.351 1.196 1.039 0.963 0.926 4.049
2.604 5.178 8.021 10.978 14.475 18.357 22.928 28.995 36.366 41.458 45.538 49.134 52.600 55.607 58.133 60.285 62.097 63.679 65.031 66.227 67.265 68.228 69.154 73.203
0.036 0.071 0.110 0.150 0.198 0.251 0.313 0.396 0.497 0.566 0.622 0.671 0.719 0.760 0.794 0.824 0.848 0.870 0.888 0.905 0.919 0.932 0.945 1.000
99.0 104.2 109.6 114.8 120.9 127.2 134.2 142.5 151.7 157.8 162.7 167.0 171.2 174.9 178.0 180.6 182.9 184.9 186.7 188.3 189.8 191.1 192.5 198.7
0.225 0.266 0.308 0.348 0.396 0.445 0.499 0.563 0.634 0.682 0.720 0.754 0.787 0.815 0.839 0.859 0.877 0.893 0.907 0.919 0.931 0.941 0.952 1.000
0.210 0.251 0.294 0.335 0.384 0.434 0.489 0.555 0.627 0.676 0.715 0.749 0.782 0.811 0.836 0.857 0.875 0.891 0.905 0.918 0.929 0.940 0.951 1.000
0.194 0.236 0.280 0.322 0.371 0.422 0.478 0.546 0.620 0.669 0.709 0.744 0.778 0.808 0.832 0.854 0.872 0.889 0.903 0.916 0.928 0.939 0.950 1.000
0.160 0.204 0.249 0.293 0.345 0.398 0.457 0.526 0.604 0.655 0.697 0.733 0.769 0.799 0.825 0.847 0.867 0.884 0.899 0.913 0.925 0.936 0.948 1.000
0.123 0.169 0.216 0.262 0.316 0.371 0.433 0.506 0.586 0.640 0.683 0.722 0.758 0.791 0.818 0.841 0.861 0.879 0.894 0.909 0.921 0.933 0.945 1.000
Total
0.3684
198.7
73.203
dictions. Whitson et al.27 proposed perhaps the most useful application of the gamma-distribution model. With Gaussian quadrature, their method allows multiple reservoir-fluid samples from a common reservoir to be treated simultaneously with a single fluid characterization. Each fluid sample can have different C7) properties when the split is made so that each split fraction has the same molecular weight (and other properties, such as g, Tb , Tc , pc , and w), while
1.0 Y h + 65
0.8
J h + 70 F h + 75 X h + 80
the mole fractions are different for each fluid sample. Example applications include the characterization of a gas cap and underlying reservoir oil and a reservoir with compositional gradient. The following outlines the procedure for applying Gaussian quadrature to the gamma-distribution function. 1. Determine the number of C7) fractions, N, and obtain the quadrature values Xi and Wi from Table 5.6 (values are given for N+3 and N+5). 2. Specify h and a. When TBP data are not available to determine these parameters, recommended values are h+90 and a+1. 3. Specify the heaviest molecular weight of fraction N (recommended value is M N + 2.5M C7)). Calculate a modified b* term, b * + ǒ M N * h ǓńX N .
0.6
0.4
0.2
0.0 0.0
0.2
0.4
0.6
0.8
1.0
Cumulative Normalized Mole Fraction, Qzi
Fig. 5.11—Graphical fit of the Hoffman et al.29 oil molar distribution by use of the cumulative-distribution type curve. Best-fit model parameters are a = 2.5 and h = 72.5. HEPTANES-PLUS CHARACTERIZATION
Fig. 5.12—Calculated normalized mole fraction vs. molecular weight of fractions for the Hoffman et al.29 oil based on the best fit in Fig. 5.11 with a = 2.5 and h = 72.5. 9
TABLE 5.6—GAUSSIAN QUADRATURE FUNCTION VARIABLES, X, AND WEIGHT FACTORS, W X
W
Three Quadrature Points (plus fractions) 1 2 3
7.110 930 099 29 10*1
0.415 774 556 783 2.294 280 360 279 6.289 945 082 937
2.785 177 335 69 10*1 1.038 925 650 16 10*2
Five Quadrature Points (plus fractions) 5.217 556 105 83 10*1 1 2 3 4 5
3.986 668 110 83 10*1
0.263 560 319 718 1.413 403 059 107 3.596 425 771 041 7.085 810 005 859 12.640 800 844 276
7.594 244 968 17 10*2 3.611 758 679 92 10*3 2.336 997 238 58 10*5
Quadrature function values and weight factors can be found for other quadrature numbers in mathematical handbooks.30
4. Calculate the parameter d. d + exp
ǒ
a b* *1 MC * h 7)
Ǔ
.
. . . . . . . . . . . . . . . . . . . (5.30)
5. Calculate the C7) mole fraction zi and Mi for each fraction. zi + zC
7)
ƪ W i f (X i)ƫ,
Mi + h ) b* Xi , and f(X) +
(X) a*1 ǒ1 ) ln dǓ a . G(a) dX
. . . . . . . . . . . . . . . . . . (5.31)
6. Check whether the calculated M C7) from Eq. 5.12 equals the measured value used in Step 4 to define d. Because Gaussian quadrature is only approximate, the calculated M C7) may be slightly in error. This can be corrected by (slightly) modifying the value of d, and repeating Steps 5 and 6 until a satisfactory match is achieved. When characterizing multiple samples simultaneously, the values of MN , h, and b* must be the same for all samples. Individual sample values of M C7) and a can, however, be different. The result of this characterization is one set of molecular weights for the C7) fractions, while each sample has different mole fractions zi (so that their average molecular weights M C7) are honored). Specific gravities for the C7) fractions can be calculated with one of the correlations given in Sec. 5.4 (e.g., Eq. 5.44), where the characterization factor (e.g., Fc ) must be the same for all mixtures. The specific gravities, g C7) , of each sample will not be exactly reproduced with this procedure (calculated with Eq. 5.37), but the average characterization factor can be chosen so that the differences are very small ( g"0.0005). Having defined Mi and gi for the C7) fractions, a complete fluid characterization can be determined with correlations in Sec. 5.5. 5.4 InspectionĆProperties Estimation 5.4.1 Generalized Properties. The molecular weight, specific gravity, and boiling point of C7) fractions must be estimated in the absence of experimental TBP data. This situation arises when simulated distillation is used or when no experimental analysis of C7) is available and a synthetic split must be made by use of a molar-distribution model. For either situation, inspection data from TBP analysis of a sample from the same field would be the most reliable source of M, g, and Tb for each C7) fraction. The next-best source would be measured TBP data from a field producing similar oil or condensate from the same geological formation. Generalized properties from a producing region, such as the North Sea, have been proposed.31 Katz and Firoozabadi6 suggest a generalized set of SCN properties for petroleum fractions C6 through C45. Table 5.2 gives an extended version of the Katz-Firoozabadi property table. Molecular 10
weights can be used to convert weight fractions, wi , from simulated distillation to mole fractions, zi +
w i ńM i
ȍ w ńM
.
N
j
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.32)
j
j+7
However, the molecular weight of the heaviest fraction, C N, is not known. From a mass balance, M N is given by wN , . . . . . . . . . . . . (5.33) MN + N*1 ǒwC ńMC Ǔ * ǒwińMiǓ 7)
7)
ȍ i+7
where Mi for i+7,…, N*1 are taken from Table 5.2. Unfortunately, the calculated molecular weight M N is often unrealistic because of measurement errors in M C7) or in the chromatographic analysis and because generalized molecular weights are only approximate. Both w N and M C7) can be adjusted to give a “reasonable” M N, but caution is required to avoid nonphysical adjustments. The same problem is inherent with backcalculating M N with any set of generalized molecular weights used for SCN Fractions 7 to N*1 (e.g., paraffin values). During the remainder of this section, molecular weights and mole fractions are assumed to be known for C7) fractions, either from chromatographic analysis or from a synthetic split. The generalized properties for specific gravity and boiling point can be assigned to SCN fractions, but the heaviest specific gravity must be backcalculated to match the measured C7) specific gravity. The calculated gN also may be unrealistic, requiring some adjustment to generalized specific gravities. Finally, the boiling point of the heaviest fraction must be estimated. TbN can be estimated from a correlation relating boiling point to specific gravity and molecular weight. 5.4.2 Characterization Factors. Inspection properties M, g, and Tb reflect the chemical makeup of petroleum fractions. Some methods for estimating specific gravity and boiling point assume that a particular characterization factor is constant for all C7) fractions. These methods are only approximate but are widely used. Watson or Universal Oil Products (UOP) Characterization Factor. The Watson or UOP factor, Kw, is based on normal boiling point, Tb , in °R and specific gravity, g.32,33 T 1ń3 K w 5 gb .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.34)
Kw varies roughly from 8.5 to 13.5. For paraffinic compounds, Kw +12.5 to 13.5; for naphthenic compounds, Kw +11.0 to 12.5; and for aromatic compounds, Kw +8.5 to 11.0. Some overlap in Kw exists among these three families of hydrocarbons, and a combination of paraffins and aromatics will obviously “appear” naphthenic. However, the utility of this and other characterization factors is that they give a qualitative measure of the composition of a petroleum fraction. The Watson characterization factor has been found to be useful for approximate characterization and is widely used as a parameter for correlating petroleum-fraction properties, such as molecular weight, viscosity, vapor pressure, and critical properties. An approximate relation2 for the Watson factor, based on molecular weight and specific gravity, is K w [ 4.5579 M 0.15178 g *0.84573 . . . . . . . . . . . . . . . . . . . (5.35) This relation is derived from the Riazi-Daubert14 correlation for molecular weight and is generally valid for petroleum fractions with normal boiling points ranging from 560 to 1,310°R (C7 through C30). Experience has shown, however, that Eq. 5.35 is not very accurate for fractions heavier than C20. Kw calculated with M C7) and g C7) in Eq. 5.35 is often constant for a given field. Figs. 5.13A and 5.13B7 plot molecular weight vs. specific gravity for C7) fractions from two North Sea fields. Data for the gas condensate in Fig. 5.13A indicate an average K wC7)+11.99"0.01 for a range of molecular weights from 135 to 150. The volatile oil shown in Fig. 5.13B has an average K wC7)+11.90"0.01 for a range of molecular weights from 220 to PHASE BEHAVIOR
Molecular Weight, MC 7+
Fig. 5.13A—Specific gravity vs. molecular weight for C7) fractions for a North Sea Gas-Condensate Field 2 (after Austad et al.7).
255. The high degree of correlation for these two fields suggests accurate molecular-weight measurements by the laboratory. In general, the spread in K wC7) values will exceed "0.01 when measurements are performed by a commercial laboratory. When the characterization factor for a field can be determined, Eq. 5.35 is useful for checking the consistency of C7) molecularweight and specific-gravity measurements. Significant deviation in K wC7) , such as "0.03 for the North Sea fields above, indicates possible error in the measured data. Because molecular weight is more prone to error than determination of specific gravity, an anomalous K wC7) usually indicates an erroneous molecular-weight measurement. For the gas condensate in Fig. 5.13A, a C7) sample with specific gravity of 0.775 would be expected to have a molecular weight of [141 (for K wC7)+ 11.99). If the measured value was 135, the Watson characterization factor would be 11.90, which is significantly lower than the field average of 11.99. In this case, the C7) molecular weight should be redetermined. Eq. 5.35 can also be used to calculate specific gravity of C7) fractions determined by simulated distillation or a synthetic split (i.e., when only mole fractions and molecular weights are known). Assuming a constant Kw for each fraction, specific gravity, gi , can be calculated from g i + 6.0108 M i0.17947 K w*1.18241 .
. . . . . . . . . . . . . . . . . (5.36)
Kw must be chosen so that experimentally measured C7) specific gravity, (g C7)) exp, is calculated correctly.
ǒgC7)Ǔ
exp
+
zC
7)
MC
7)
ȍǒz M ńg Ǔ N
i
i
.
. . . . . . . . . . . . . . . . . . . . . (5.37)
i
i+1
The Watson factor satisfying Eq. 5.37 is given by Kw +
ƪ
0.16637 g C zC
7)
MC
ȍz M
A 7) 0
7)
ƫ
*0.84573
,
. . . . . . . . . . . . . . . (5.38)
Molecular Weight, MC 7+
Fig. 5.13B—Specific gravity vs. molecular weight for C7) fractions for a North Sea Volatile-Oil Field 3B(after Austad et al.7).
Jacoby Correlation (Aromaticity Factor, Ja ) Present Correlation (Watson Factor, Kw )
Ja
Fig. 5.14—Specific gravity vs. molecular weight for constant values of the Jacoby aromaticity factor (solid lines) and the Watson characterization factor (dashed lines). After Whitson.25
Boiling points, Tbi , can be estimated from Eq. 5.36. 3
T bi + (K wg i) .
i
0.82053 . i
. . . . . . . . . . . . . . . . . . . . . . (5.39)
i+1
HEPTANES-PLUS CHARACTERIZATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.40)
Unfortunately, Eqs. 5.36 through 5.40 overpredict g and Tb at molecular weights greater than [250 (an original limitation of the Riazi-Daubert14 molecular-weight correlation). Jacoby Aromaticity Factor. The Jacoby aromaticity factor, Ja , is an alternative characterization factor for describing the relative composition of petroleum fractions.34 Fig. 5.142 shows the original Jacoby relation between specific gravity and molecular weight for several values of Ja . The behavior of specific gravity as a function of molecular weight is similar for the Jacoby factor and the relation for a constant Kw. However, specific gravity calculated with the Jacoby method increases more rapidly at low molecular weights, flattening at high molecular weights (a more physically consistent behavior). A relation for the Jacoby factor is
N
where A 0 +
Kw
Ja +
g * 0.8468 ) ǒ15.8ńMǓ . . . . . . . . . . . . . . . . . . (5.41) 0.2456 * ǒ1.77ńMǓ 11
Cf typically has a value between 0.27 and 0.31 and is determined for a specific C7) sample by satisfying Eq. 5.37. 5.4.3 Boiling-Point Estimation. Boiling point can be estimated from molecular weight and specific gravity with one of several correlations. Søreide also developed a boiling-point correlation based on 843 TBP fractions from 68 reservoir C7) samples, T b + 1928.3 * ǒ1.695 exp ƪ * ǒ4.922 ) ǒ3.462
Fig. 5.15—Specific gravity vs. carbon number for constant values of the Yarborough aromaticity factor (after Yarborough1).
or, in terms of specific gravity,
ǒ
Ǔ
g + 0.8468 * 15.8 ) J a 0.2456 * 1.77 . . . . . . . (5.42) M M The first two terms in Eq. 5.42 (i.e., when Ja +0) express the relation between specific gravity and molecular weight for normal paraffins. The Jacoby factor can also be used to estimate fraction specific gravities when mole fractions and molecular weights are available from simulated distillation or a synthetic split. The Jacoby factor satisfying measured C7) specific gravity (Eq. 5.37) must be calculated by trial and error. We have found that this relation is particularly accurate for gas-condensate systems.27 Yarborough Aromaticity Factor. Yarborough1 modified the Jacoby aromaticity factor specifically for estimating specific gravities when mole fractions and molecular weights are known. Yarborough tries to improve the original Jacoby relation by reflecting the changing character of fractions up to C13 better and by representing the larger naphthenic content of heavier fractions better. Fig. 5.15 shows how the Yarborough aromaticity factor, Ya , is related to specific gravity and carbon number. A simple relation representing Ya is not available; however, Whitson26 has fit the seven aromaticity curves originally presented by Yarborough using the equation g i + expƪA 0 ) A 1 i *1 ) A 2 i ) A 3 ln(i)ƫ , . . . . . . . . . . (5.43) where i+carbon number. Table 5.7 gives the constants for Eq. 5.43. The aromaticity factor required to satisfy measured C7) specific gravity (Eq. 5.37) is determined by trial and error. Linear interpolation of specific gravity should be used to calculate specific gravity for a Ya value falling between two values of Ya in Table 5.7. Søreide 35 Correlations. Søreide developed an accurate specificgravity correlation based on the analysis of 843 TBP fractions from 68 reservoir C7) samples. g i + 0.2855 ) C f (M i * 66) 0.13 .
. . . . . . . . . . . . . . . (5.44)
10 5Ǔ M *0.03522 g 3.266 10 *3Ǔ M * 4.7685 g
10 *3Ǔ Mgƫ ,
. . . . . . . . . . . . . . . . . . . . . (5.45)
with Tb in °R. Table 5.8 gives estimated specific gravities determined with the methods just described for a C7) sample with the exponential split given in Table 5.4 (a+1, h+90, M C7)+200) and g C7)+0.832. The following equations also relate molecular weight to boiling point and specific gravity; any of these correlations can be solved for boiling point in terms of M and g. We recommend, however, the Søreide correlation for estimating Tb from M and g. Kesler and Lee. 12 M + ƪ* 12, 272.6 ) 9, 486.4g ) (4.6523 * 3.3287g)T bƫ ) NJ ǒ1 * 0.77084g * 0.02058g 2Ǔ
Ǔ ƪǒ1.3437 * 720.79T *1 b
Nj 10 7ƫ T *1 b
) NJǒ1 * 0.80882g ) 0.02226g 2Ǔ
Ǔ ƪǒ1.8828 * 181.98T –1 b
Nj. 10 12ƫ T *3 b
. . . . . . . . (5.46)
Riazi and Daubert. 14 M + (4.5673
10 *5)T b2.1962 g *1.0164 .
. . . . . . . . . . . . (5.47)
American Petroleum Inst. (API). 36 M + ǒ2.0438
10 2Ǔ T b0.118 g 1.88 expǒ0.00218T b * 3.07gǓ . . . . . . . . . . . . . . . . . . . . . (5.48)
Rao and
Bardon. 37
ln M + (1.27 ) 0.071K w) ln
ǒ22.311.8T Ǔ. ) 1.68K b
w
. . . . . . . . . . . . . . . . . . . . (5.49) Riazi and Daubert. 18 M + 581.96 T b0.97476 g 6.51274 expƪǒ5.43076 * 9.53384 g ) ǒ1.11056
10 *3ǓT b
10 *3ǓT bgƫ . . . . . . . . . . (5.50)
TABLE 5.7—COEFFICIENTS FOR YARBOROUGH AROMATICITY FACTOR CORRELATION1,26
12
Ya
A0
A1
0.0
*7.43855 10*2
*1.72341
0.1
*4.25800 10*1
0.2
A2
A2
1.38058 10*3
*3.34169 10*2
*7.00017 10*1
*3.30947 10*5
8.65465 10*2
*4.47553 10*1
*7.65111 10*1
1.77982 10*4
1.07746 10*1
0.3
*4.39105 10*1
*9.44068 10*1
4.93708 10*4
1.19267 10*1
0.4
*2.73719 10*1
*1.39960
3.80564 10*3
5.92005 10*2
0.6
*7.39412 10*3
*1.97063
5.87273 10*3
*1.67141 10*2
0.8
*3.17618 10*1
*7.78432 10*1
2.58616 10*3
1.08382 10*3 PHASE BEHAVIOR
TABLE 5.8—COMPARISON OF SPECIFIC GRAVITIES WITH CORRELATIONS BY USE OF DIFFERENT CHARACTERIZATION FACTORS gi for Different Correlations With Constant Characterization Factor Chosen To Match g C + 0.832 7)
Kw +12.080
Ja +0.2395
Ya +0.2794
Cf +0.2864
96.8
0.7177
0.7472
0.7051
0.7327
0.1052
110.8
0.7353
0.7684
0.7286
0.7550
0.0926
124.8
0.7511
0.7849
0.7486
0.7719
4
0.0816
138.8
0.7656
0.7981
0.7660
0.7856
5
0.0718
152.8
0.7789
0.8088
0.7813
0.7972
6
0.0632
166.8
0.7913
0.8178
0.7951
0.8072
7
0.0557
180.8
0.8028
0.8253
0.8075
0.8161
8
0.0490
194.8
0.8136
0.8318
0.8189
0.8241
9
0.0432
208.8
0.8238
0.8374
0.8294
0.8314
10
0.0380
222.8
0.8335
0.8423
0.8391
0.8380
Fraction
zi
1
0.1195
2 3
Mi
11
0.0335
236.8
0.8426
0.8466
0.8482
0.8442
12
0.0295
250.8
0.8514
0.8505
0.8567
0.8500
13
0.0259
264.8
0.8597
0.8539
0.8646
0.8554
14
0.0228
278.8
0.8677
0.8570
0.8722
0.8604
15
0.0201
292.8
0.8753
0.8598
0.8793
0.8652
16
0.0177
306.8
0.8827
0.8623
0.8861
0.8697
17
0.0156
320.8
0.8898
0.8646
0.8926
0.8740
18
0.0137
334.8
0.8966
0.8668
0.8988
0.8782
19
0.0121
348.8
0.9033
0.8687
0.9048
0.8821
20
0.0891
466.0
0.9514
0.8805
0.9468
0.9096
1.0000
200.0
0.8320
0.8320
0.8320
0.8320
Total
5.5 CriticalĆProperties Estimation
Kesler-Lee. 12
Thus far, we have discussed how to split the C7) fraction into pseudocomponents described by mole fraction, molecular weight, specific gravity, and boiling point. Now we must consider the problem of assigning critical properties to each pseudocomponent. Critical temperature, Tc ; critical pressure, pc ; and acentric factor, w, of each component in a mixture are required by most cubic EOS’s. Critical volume, vc , is used instead of critical pressure in the Benedict-Webb-Rubin38 (BWR) EOS, and critical molar volume is used with the LBC viscosity correlation.24 Critical compressibility factor has been introduced as a parameter in three- and four-constant cubic EOS’s. Critical-property estimation of petroleum fractions has a long history beginning as early as the 1930’s; several reviews22,25,26,39,40 are available. We present the most commonly used correlations and a graphical comparison (Figs. 5.16 through 5.18) that is intended to highlight differences between the correlations. Finally, correlations based on perturbation expansion (a concept borrowed from statistical mechanics) are discussed separately. The units for the remaining equations in this section are Tb in °R, TbF in °F+Tb *459.67, Tc in °R, pc in psia, and vc in ft3/lbm mol. Oil gravity is denoted gAPI and is related to specific gravity by gAPI+141.5/g*131.5.
T c + 341.7 ) 811g ) (0.4244 ) 0.1174g)T b
5.5.1 Critical Temperature. Tc is perhaps the most reliably correlated critical property for petroleum fractions. The following critical-temperature correlations can be used for petroleum fractions. Roess. 41 (modified by API36). T c + 645.83 ) 1.6667ƪgǒ T bF ) 100 Ǔƫ * ǒ0.7127
2
10 *3Ǔƪgǒ T bF ) 100 Ǔƫ .
HEPTANES-PLUS CHARACTERIZATION
) (0.4669 * 3.2623g)
. . . . . . . . . . . . (5.52)
Cavett. 42 T c + 768.07121 ) 1.7133693T bF * ǒ0.10834003
2 10 *2ǓT bF
* ǒ0.89212579
10 *2Ǔ g APIT bF
) ǒ0.38890584
3 10 *6ǓT bF
) ǒ0.5309492 ) ǒ0.327116
2 10 *5Ǔ g APIT bF 2 . 10 *7Ǔ g 2APIT bF
. . . . . . . . . . . . . . . (5.53)
Riazi-Daubert. 14 T c + 24.27871T b0.58848 g 0.3596 .
. . . . . . . . . . . . . . . . . . (5.54)
Nokay. 43 T c + 19.078 T b0.62164 g 0.2985 .
. . . . . . . . . . . . . . . . . . . . (5.55)
5.5.2 Critical Pressure. pc correlations are less reliable than Tc correlations. The following are pc correlations that can be used for petroleum fractions. Kesler-Lee. 12 ln p c + 8.3634 * 0.0566 g *
. . . . . . . . . . . (5.51)
10 5T *1 b .
ƪǒ
0.11857 0.24244 ) 2.2898 g ) g2
Ǔ
ƫ
10 *3 T b 13
Fig. 5.16—Comparison of critical-temperature correlations for boiling points from 600 to 1,500°R assuming a constant Watson characterization factor of 12.
)
*
ƪǒ ƪǒ
0.47227 1.4685 ) 3.648 g ) g2 0.42019 ) 1.6977 g2
ƫ
Ǔ
10 *7 T 2b
ƫ
Ǔ
Fig. 5.17—Comparison of critical-pressure correlations for boiling points from 600 to 1,500°R assuming a constant Watson characterization factor of 12.
10 *10 T 3b .
. . . . . (5.56)
Cavett. 42 log p c + 2.8290406 ) ǒ0.94120109 * ǒ0.30474749 * ǒ0.2087611
10 *3ǓT bF
2 10 *5ǓT bF
10 *4Ǔ g APIT bF
) ǒ0.15184103
3 10 *8ǓT bF
) ǒ0.11047899
2 10 *7Ǔ g APIT bF
* ǒ0.48271599
10 *7Ǔ g 2APIT bF
) ǒ0.13949619
2 . . . . . . . . . . . . (5.57) 10 *9Ǔ g 2APIT bF
Riazi-Daubert. 14 p c + ǒ3.12281
10 9ǓT *2.3125 g 2.3201 . . . . . . . . . . . . . . (5.58) b
5.5.3 Acentric Factor. Pitzer et
ǒǓ
p* w 5 * log pv * 1, c
al.44
Lee-Kesler. 13 (Tbr +Tb /Tc t0.8).
defined acentric factor as w+
– lnǒ p cń14.7Ǔ ) A 1 ) A 2 T *1 ) A 3 ln T br ) A 4 T br6 br
. . . . . . . . . . . . . . . . . . . . . . . . (5.59)
where p *v+vapor pressure at temperature T+0.7Tc (Tr +0.7). Practically, acentric factor gives a measure of the steepness of the vapor-pressure curve from Tr +0.7 to Tr +1, where p *v /pc +0.1 for w+0 and p *v /pc +0.01 for w+1. Numerically, w[0.01 for methane, [0.25 for C5, and [0.5 for C8 (see Table A.1 for literature values of acentric factor for pure compounds). w increases to u1.0 for petroleum fractions heavier than approximately C25 (see Table 5.2). The Kesler-Lee12 acentric factor correlation (for Tb /Tc u0.8) is developed specifically for petroleum fractions, whereas the correlation for Tb /Tc t0.8 is based on an accurate vapor-pressure correlation for pure compounds. The Edmister45 correlation is limited to pure hydrocarbons and should not be used for C7) fractions. The three correlations follow. 14
Fig. 5.18—Comparison of acentric factor correlations for boiling points from 600 to 1500°R assuming a constant Watson characterization factor of 12.
A 5 ) A 6 T *1 ) A 7 ln T br ) A 8 T br6 br
,
. . . . . . . . . . . . . . . . . . . . (5.60) where A1+*5.92714, A2+ 6.09648, A3+ 1.28862, A4+ *0.169347, A5+ 15.2518, A6+*15.6875, A7+*13.4721, and A8+ 0.43577. Kesler-Lee. 12 (Tbr +Tb /Tc u0.8). w + * 7.904 ) 0.1352K w * 0.007465K 2w ) 8.359T br ) (1.408 * 0.01063K w)T *1 br .
. . . . . . . (5.61)
Edmister. 45 logǒ p cń14.7Ǔ w+3 * 1. 7 ƪǒT cńT bǓ * 1ƫ
. . . . . . . . . . . . . . . . . . . . . (5.62) PHASE BEHAVIOR
5.5.4 Critical Volume. The Hall-Yarborough46 critical-volume correlation is given in terms of molecular weight and specific gravity, whereas the Riazi-Daubert14 correlation uses normal boiling point and specific gravity. Hall-Yarborough. 46 v c + 0.025 M 1.15 g *0.7935 .
. . . . . . . . . . . . . . . . . . . . . . (5.63)
Riazi-Daubert. 14 v c + ǒ7.0434
10 *7Ǔ T b2.3829 g *1.683.
. . . . . . . . . . . . . (5.64)
Critical compressibility factor, Zc , is defined as Zc +
p cv c , . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.65) RT c
where R+universal gas constant. Thus, Zc can be calculated directly from critical pressure, critical volume, and critical temperature. Reid et al.40 and Pitzer et al.44 give an approximate relation for Zc . Z c [ 0.291 * 0.08w.
Paraffin molecular weight, MP, is not explicitly a function of Tb , and Eqs. 5.67 through 5.73 must be solved iteratively; an initial guess is given by MP [
Tb . 10.44 * 0.0052T b
. . . . . . . . . . . . . . . . . . . . . (5.74)
Twu claims that the normal-paraffin correlations are valid for C1 through C100, although the properties at higher carbon numbers are only approximate because experimental data for paraffins heavier than approximately C20 do not exist. The following relations are used to calculate petroleum-fraction properties. Critical Temperature.
ǒ11 )* 2f2f Ǔ , 2
T c + T cP
T T
f T + Dg T
ƪ
* 0.362456 ) T b0.5
Ǔ ƫ
ǒ
0.0398285 * 0.948125 Dg T , T b0.5
. . . . . . . . . . . . . . . . . . . . . . . . . (5.66)
Eq. 5.66 is not particularly accurate (grossly overestimating Zc for heavier compounds) and is used only for approximate calculations.
and Dg T + exp[5(g P * g)] * 1.
. . . . . . . . . . . . . . . . . . (5.75)
Critical Volume.
ǒ11 )* 2f2f Ǔ , 2
5.5.5 Correlations Based on Perturbation Expansions. Correlations for critical temperature, critical pressure, critical volume, and molecular weight have been developed for petroleum fractions with a perturbation-expansion model with normal paraffins as the reference system. To calculate critical pressure, for example, critical temperature, critical volume, and specific gravity of a paraffin with the same boiling point as the petroleum fraction must be calculated first. Kesler et al.47 first used the perturbation expansion (with n-alkanes as the reference fluid) to develop a suite of critical-property and acentric-factor correlations. Twu48 uses the same approach to develop a suite of critical-property correlations. We give his normal-paraffin correlations first, then the correlations for petroleum fractions. Normal Paraffins (Alkanes).
ƪ
T cP + T b 0.533272 ) ǒ0.191017 ) ǒ0.779681
10
*3
(0.959468 10 2) ) ǒ0.01T bǓ 13
ƫ
10 *10ǓT b3
*1
,
. . . . . . . . . . . . . . . . . . (5.67)
2
. . . . . . . . . . . . . . . (5.68)
v cP + [ 1 * (0.419869 * 0.505839a * 1.56436a 3 ,
. . . . . . . . . . . . . . . . . . . . . . . . . (5.69)
g P + 0.843593 * 0.128624a * 3.36159a 3 * 13749.5a 12 ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.70)
and T b + exp(5.71419 ) 2.71579q * 0.28659q 2 * 39.8544q *1 * 0.122488q *2) * 24.7522q ) 35.3155q 2 , T where a + 1 * b T cP and q + ln M P .
0.466590 ) T b0 .5
ǒ
Ǔ ƫ
* 0.182421 ) 3.01721 Dg v , T b0.5
and Dg v + expƪ4ǒg 2P * g 2Ǔƫ * 1.
. . . . . . . . . . . . . . . . . . (5.76)
Critical Pressure.
ǒTT ǓǒVV Ǔǒ11 )* 2f2f Ǔ , 2
p c + p cP
)
c
cP
p
cP
c
p
ƪǒ
2.53262 * 46.1955 * 0.00127885T b T b0.5
Ǔ
Ǔ ƫ
ǒ
* 11.4277 ) 252.14 ) 0.00230535T b Dg p , T b0.5
and Dg p + exp[0.5(g P * g)] * 1. . . . . . . . . . . . . . . . . . (5.77) 1 ) 2f Ǔ, ln M + ln M ǒ 1 * 2f 2
M
) 36.1952a 2 ) 104.193a 4) ,
*8
ƪ
f v + Dg v
v
Molecular Weight.
p cP + (3.83354 ) 1.19629a 0.5 ) 34.8888a
* 9481.7a 14)]
v
f p + Dg p
ǓT b
10 *7ǓT b2 * ǒ0.284376
v c + v cP
. . . . . . . . . . . . . . . . . (5.71)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.72)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.73)
HEPTANES-PLUS CHARACTERIZATION
P
ƪ ǒ
f M + Dg M |x| )
M
Ǔ ƫ
* 0.0175691 ) 0.193168 Dg M , T b0.5
x + 0.012342 * 0.328086 , T b0.5 and Dg M + exp[5(g P * g)].
. . . . . . . . . . . . . . . . . . . . . (5.78)
Figs. 5.16 through 5.18 compare the various critical-property correlations for a range of boiling points from 600 to 1,500°R. 5.5.6 Methods Based on an EOS. Fig. 5.1928 illustrates the important influence that critical properties have on EOS-calculated properties of pure components. Vapor pressure is particularly sensitive to critical temperature. For example, the Riazi-Daubert19 critical-temperature correlation for toluene overpredicts the experimental value 15
a+1, h+90) with Gaussian-quadrature or equal-mass fractions or (2) the exponential distribution (Eq. 5.7). Specific gravities should be estimated with the Søreide35 correlation (Eq. 5.44), choosing Cf to match measured C7) specific gravity (Eq. 5.37). Boiling points should be estimated from the Søreide correlation (Eq. 5.45). For the PR EOS, we recommend the nonhydrocarbon BIP’s given in Chap. 4 and the modified Chueh-Prausnitz54 equation for C1 through C7) pairs,
k ij
ȱ + Aȧ1 * Ȳ
ǒ
2v 1ń6 v 1ń6 ci cj v 1ń3 ) v 1ń3 ci cj
Ǔ ȳȴȧ B
,
. . . . . . . . . . . . . . . . (5.79)
with A+0.18 and B+6.
Tc underpredicted←
→Tc overpredicted
Deviation From Experimental Value, % Fig. 5.19—Effect of critical temperature on vapor-pressure prediction of toluene with the PR EOS; AAD+absolute average deviation (after Brulé et al.28).
by only 1.7%. Even with this slight error in Tc , the average error in vapor pressures predicted by the Peng-Robinson49 (PR) EOS is 16%. The effect of critical properties and acentric factor on EOS calculations for reservoir-fluid mixtures is summarized by Whitson.26 In principle, the EOS used for mixtures should also predict the behavior of individual components found in the mixture. For pure compounds, the vapor pressure is accurately predicted because all EOS’s force fit vapor-pressure data. Some EOS’s are also fit to saturated-liquid densities at subcritical temperatures. The measured properties of petroleum fractions, boiling point, and specific gravity can also be fit by the EOS, as discussed later. For each petroleum fraction separately, two of the EOS parameters (Tc ; pc ; w; volume-shift factor, s; or multipliers of EOS constants A and B) can be chosen so that the EOS exactly reproduces experimental boiling point and specific gravity. Because only two inspection properties are available (Tb and g), only two of the EOS parameters can be determined. Whitson50 suggests fixing the value of w with an empirical correlation and adjusting Tc and pc to match normal boiling point and molar volume (M/g) at standard conditions. Critical properties satisfying these criteria are given for a wide range of petroleum fractions by the PR EOS and the Soave-RedlichKwong (SRK) EOS.22,23 A better (and recommended) approach for cubic EOS’s is to use the volume-shift factor s (see Chap. 4) to match specific gravity or a saturated liquid density and acentric factor to match normal boiling point. Other methods for forcing the EOS to match boiling point and specific gravity have also been devised. Brulé and Starling51 proposed a method that uses viscosity as an additional inspection property of the fraction for determining critical properties. This approach proved particularly successful when applied to the BWR EOS for residual-oil supercritical extraction (ROSE).28 5.6 Recommended C7) Characterizations We recommend the following C7) characterization procedure for cubic EOS’s. 1. Use the Twu48 (or Lee-Kesler12) critical property correlation for Tc and pc . 2. Choose the acentric factor to match Tb ; alternatively, use the Lee-Kesler12/Kesler-Lee13 correlations. 3. Determine volume-translation coefficients, si , to match specific gravities; alternatively, use Peneloux et al.’s52 correlation for the SRK EOS22,23 or Jhaveri and Youngren’s53 correlation for the PR EOS.49 When measured TBP data are not available, a mathematical split should be made with either (1) the gamma distribution (default 16
5.6.1 SRK-Recommended Characterization. Alternatively, the Pedersen et al.55 characterization procedure can be used with the SRK EOS. 1. Split the plus fraction Cn) (preferably nu10) into SCN fractions up to C80 using Eqs. 5.7 through 5.11 and h+*4. 2. Calculate SCN densities ò i (gi + ò i /0.999) using the equation ò i+A0)A1 ln(i), where A0 and A1 are determined by satisfying the experimental-plus density, ò n), and measured (or assumed) density, ò n *1 ( ò6+0.690 can be used for C7)). 3. Calculate critical properties of all C7) fractions (distillation cuts from C7 to Cn*1 and split SCN fractions from Cn through C80) using the correlations T c + 163.12 ò ) 86.052 ln M ) 0.43475 M * 1877.4 , M , ln p c + * 0.13408 ) 2.5019 ò ) 208.46 * 3987.2 M M2 and m SRK + 0.48 ) 1.574 w * 0.176 w 2 + 0.7431 ) 0.0048122 M ) 0.0096707 ò * ǒ3.7184
10 *6ǓM 2. . . . . . . . . . . . . . . . . . . (5.80)
Note that the use of acentric factor is circumvented by directly calculating the term m used in the a correction term to EOS Constant A. 4. Group C7) into 3 to 12 fractions using equal-weight fractions in each group; use weight-average mixing rules. 5. Calculate volume-translation parameters for C7) fractions to match specific gravities; pure component c values are taken from Peneloux et al.52 6. All hydrocarbon/hydrocarbon BIP’s are set to zero. SRK BIP’s given in Chap. 4 are used for nonhydrocarbon/hydrocarbon pairs. The two recommended C7) characterization procedures outlined previously for the PR EOS and SRK EOS are probably the best currently available (other EOS characterizations, such as the Redlich-Kwong EOS modified by Zudkevitch and Joffe,56 and some three-constant characterizations should provide similar accuracy but are not significantly better). Practically, the two characterization procedures give the same results for almost all PVT properties (usually within 1 to 2%). With these EOS-characterization procedures, we can expect reasonable predictions of densities and Z factors ("1 to 5%), saturation pressures ("5 to 15%), gas/oil ratios and formation volume factors ("2 to 5%), and condensate-liquid dropout ("5 to 10% for maximum dropout, with poorer prediction of taillike behavior just below the dewpoint). The recommended EOS methods are less reliable for prediction of minimum miscibility conditions, near-critical saturation pressure and saturation type (bubblepoint or dewpoint), and both retrograde and near-critical liquid volumes. Improved predictions can be obtained only by tuning EOS parameters to accurate PVT data covering a relatively wide range of pressures, temperatures, and compositions (see Sec. 4.7 and Appendix C). 5.7 Grouping and Averaging Properties The cost and computer resources required for compositional reservoir simulation increase substantially with the number of compoPHASE BEHAVIOR
nents used to describe the reservoir fluid. A compromise between accuracy and the number of components must be made according to the process being simulated (i.e., according to the expected effect that phase behavior will have on simulated results). For example, a detailed fluid description with 12 to 15 components may be needed to simulate developed miscibility in a slim-tube experiment. With current computer technology, however, a full-field simulation with fluids exhibiting near-critical phase behavior is not feasible for a 15-component mixture. The following are the main questions regarding component grouping. 1. How many components should be used? 2. How should the components be chosen from the original fluid description? 3. How should the properties of pseudocomponents be calculated?
the method is general and can be applied to any molar-distribution model and for any number of C7) groups. In general, most authors have found that broader grouping of C7) as C7 through C10, C11 through C15, C16 through C20, and C21) is substantially better than splitting only the first few carbon-number fractions (e.g., C7, C8, C9, and C10)). Gaussian quadrature is recommended for choosing the pseudocomponents in a C7) fraction; equal-mass fractions or the Li et al.59 approach are valid alternatives. 5.7.2 Mixing Rules. Several methods have been proposed for calculating critical properties of pseudocomponents. The simplest and most common mixing rule is
ȍz q q + ȍz , i i
iŮI
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.83)
I
5.7.1 How Many and Which Components To Group. The number of components used to describe a reservoir fluid depends mainly on the process being simulated. However, the following rule of thumb reduces the number of components for most systems: group N2 with methane, CO2 with ethane, iso-butane with n-butane, and iso-pentane with n-pentane. Nonhydrocarbon content should be less than a few percent in both the reservoir fluid and the injection gas if a nonhydrocarbon is to be grouped with a hydrocarbon. Five- to eight-component fluid characterizations should be sufficient to simulate practically any reservoir process, including (1) reservoir depletion of volatile-oil and gas-condensate reservoirs, (2) gas cycling above and below the dewpoint of a gas-condensate reservoir, (3) retrograde condensation near the wellbore of a producing well, and (4) immiscible and miscible gas-injection. Coats57 discusses a method for combining a modified black-oil formula with a simplified EOS representation of separator oil and gas streams. The “oil” and “gas” pseudocomponents in this model contain all the original fluid components in contrast to the typical method of grouping where each pseudocomponent is made up of only selected original components. Lee et al.58 suggest that C7) fractions can be grouped into two pseudocomponents according to a characterization factor determined by averaging the tangents of fraction properties M, g, and Ja plotted vs. boiling point. Whitson2 suggests that the C7) fraction can be grouped into NH pseudocomponents given by
i
iŮI
where qi +any property (Tc , pc , w, or M) and zi +original mole fraction for components (i+1,..., I) making up Pseudocomponent I. Average specific gravity should always be calculated with the assumption of ideal solution mixing.
ȍz M . g + ȍǒz M ńg Ǔ i
i
iŮI
. . . . . . . . . . . . . . . . . . . . . . . . . . . (5.84)
I
i
i
i
iŮI
Pedersen et al.55 and others suggest use of weight fraction instead of mole fraction. Wu and Batycky’s63 empirical mixing-rule approach uses both the molar- and weight-average mixing rules and a proportioning factor, F, to calculate pcI , TcI , and wI . qI +
ȍf q ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.85)
i i
iŮI
where qI represents pcI , TcI , and wI and fi +average of the molar and weight fractions, f i + F q iz i ) (1 * F) q i w i and w i +
N H + 1 ) 3.3 log(N * 7), . . . . . . . . . . . . . . . . . . . . . (5.81)
zi Mi
ȍz M
,
N
j
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.86)
j
j+1
where N+carbon number of the heaviest fraction in the original fluid description. The groups are separated by molecular weights MI given by MI + MC
7
ǒM
N ń MC
7
Ǔ
1ńN H
,
. . . . . . . . . . . . . . . . . . . (5.82)
where I+1,..., NH . Molecular weights, Mi , from the original fluid description (i+7,..., N) falling within boundaries MI*1 to MI are included in Group I. This method should only be used when C7) fractions are originally separated on a carbon-number basis and for N greater than [20. Li et al.59 suggest a method for grouping components of an original fluid description that uses K values from a flash at reservoir temperature and the “average” operating pressure. The original mixture is divided arbitrarily into “light” components (H2S, N2, CO2, and C1 through C6) and “heavy” components (C7)). Different criteria are used to determine the number of light and heavy pseudocomponents. Li et al. also suggest use of phase diagrams and compositional simulation to verify the grouped fluid description (a practice that we highly recommend). Still other pseudoization methods have been proposed60,61; Schlijper’s61 method also treats the problem of retrieving detailed compositional information from pseudoized (grouped) components. Behrens and Sandler62 suggest a grouping method for C7) fractions based on application of the Gaussian-quadrature method to continuous thermodynamics. Although a simple exponential distribution is used with only two quadrature points (i.e., the C7) fractions are grouped into two pseudocomponents), Whitson et al.27 show that HEPTANES-PLUS CHARACTERIZATION
with 0xFx1. A generalized mixing rule for BIP’s can be written k IJ +
ȍȍf f k
j ij ,
i
. . . . . . . . . . . . . . . . . . . . . . . . . (5.87)
iŮI jŮJ
where fi is also given by Eq. 5.86. On the basis of Chueh and Prausnitz’s54 arguments, Lee-Kesler13 proposed the mixing rules in Eqs. 5.88 through 5.92. v cI +
ƪ ȍȍ ǒ ƪ ȍȍ 1 8
T cI +
)
v 1ń3 cj
iŮI jŮJ
1 8v cI
2
i
,
. . . (5.88)
iŮI
ǒ
z i z j ǒT ci T cjǓ 1ń2 v 1ń3 ) v 1ń3 ci cj
iŮI jŮJ
ǒ Ǔ ǒȍ Ǔń ǒȍ Ǔ
B
ȍz
ƫǒ Ǔ
Ǔ ń ȍz 3
z i z j v 1ń3 ci
Ǔ
3
ƫ
2
i
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.89)
iŮI
wI +
zi wi
iŮI
zi ,
Z cI + 0.2905 * 0.085w I , and p cI +
Z cI R T cI v cI .
. . . . . . . . . . . . . . . . . . . (5.90)
iŮI
. . . . . . . . . . . . . . . . . . . . . . (5.91)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (5.92) 17
TABLE 5.9—EXAMPLE STEPWISE-REGRESSION PROCEDURE FOR PSEUDOIZATION TO FEWER COMPONENTS FOR A GAS CONDENSATE FLUID UNDERGOING DEPLETION Original Component
Original
Number
Component
Step 1
Step 2
Step 3
Step 4
Step 5
1
N2
N2)C1*
N2)C1
N2)C1
N2)C1)CO2)C2*
N2)C1)CO2)C2
2
CO2
CO2)C2*
CO2)C2
CO2)C2
C3)i-C4)n-C4
C3)i-C4)n-C4
)i-C5)n-C5)C6*
)i-C5)n-C5)C6
3
C1
C3
C3
C3)i-C4)n-C4*
F1
F1
4
C2
i-C4
i-C4)n-C4*
i-C5)n-C5)C6*
F2
F2)F3*
5
C3
n-C4
i-C5)n-C5*
F1
F3
6
i-C4
i-C5
C6
F2
7
n-C4
n-C5
F1
F3
8
i-C5
C6
F2 F3
9
n-C5
F1
10
C6
F2 F3
11
F1
12
F2
13
F3 Regression Parameters
kij
1, 9, 10, and 11
1, 7, 8, and 9
1, 5, 6, and 7
1, 3, 4, and 5
1, 3, and 4
Wa
1
4
3
1
3
Wb
1
4
3
1
3
Wa
2
5
4
2
4
Wb
2
5
4
2
4
*Indicates the grouped pseudocomponents being regressed in a particular step.
Lee et al.58 and Whitson2 consider an alternative method for calculating C7) critical properties based on the specific gravities and boiling points of grouped pseudocomponents. Coats57 presents a method of pseudoization that basically eliminates the effect of mixing rules on pseudocomponent properties. The approach is simple and accurate. Coats requires the pseudoized characterization to reproduce exactly the volumetric behavior of the original reservoir fluid at undersaturated conditions. This is achieved by ensuring that the mixture EOS constants A and B are identical for the original and the pseudoized characterizations. First, pseudocritical properties ( pcI , TcI , and wI ) are estimated with any mixing rule (e.g., Kay’s64 mixing rule). Then W aI and W bI are determined to satisfy the following equations.
ƪȍ W aI +
iŮI
ȍ zi zj aiaj ǒ1 * kijǓ jŮJ
zi
iŮI
ǒR 2TcI2 ńpcIǓa I(TrI, w I)
ǒȍ Ǔń ǒȍ Ǔ zi bi
and W bI +
ƫńǒȍ Ǔ
2
iŮI
zi
iŮI
ǒRT cIńp cIǓb I(T rI, w I)
,
. . . . . . . . . . . . . . . . (5.93)
R 2T 2 where a i + W ai p ci a i (T ri, w i) ci RT and b i + W bi p ci b i(T ri, w i) . ci
. . . . . . . . . . . . . . . . . . . . . (5.94)
W ai and W bi may include previously determined corrections to the numerical constants W oa and W ob. This approach to determining pseudocomponent properties, together with Eq. 5.87 for k I J , is surprisingly accurate even for VLE calculations. Coats also gives an 18
analogous procedure for determining pseudocomponent vcI for the LBC24 viscosity correlation. Coats’ approach is preferred to all the other proposed methods. It ensures accurate volumetric calculations that are consistent with the original EOS characterization, and the method is easy to implement. 5.7.3 Stepwise Regression. A reduced-component characterization should strive to reproduce the original complete characterization that has been used to match measured PVT data. One approach to achieve this goal is stepwise regression, summarized in the following procedure. 1. Complete a comprehensive match of all existing PVT data with a characterization containing light and intermediate pure components and at least three to five C7) fractions. 2. Simulate a suite of depletion and multicontact gas-injection PVT experiments that cover the expected range of compositions in the particular application. 3. Use the simulated PVT data as “real” data for pseudoization based on regression. 4. Create two new pseudocomponents from the existing set of components. Use the pseudoization procedure of Coats to obtain WaI and WbI values, and use Eq. 5.87 for k I J . 5. Use regression to fine tune the W aI and W bI values estimated in Step 4; also regress on key BIP’s, such as (N2)C1)*C7), (CO2)C2)*C7), and other nonzero BIP’s involving pseudocomponents from Step 4. 6. Repeat Steps 4 and 5 until the quality of the characterization deteriorates beyond an acceptable fluid description. Table 5.9 shows an example five-step pseudoization procedure. In summary, any grouping of a complete EOS characterization into a limited number of pseudocomponents should be checked to ensure that predicted phase behavior (e.g., multicontact gas injection data, saturation pressures, and densities) are reasonably close to the predictions for the original (complete) characterization. Stepwise regression is the best approach to determine the number and PHASE BEHAVIOR
properties of pseudocomponents that can accurately describe a reservoir fluid’s phase behavior. If stepwise regression is not possible, standard grouping of the light and intermediates (N2)C1, CO2)C2, i-C4)n-C4, and i-C5)n-C5) and Gaussian quadrature for C7) (or equal-mass fractions) is recommended; a valid alternative is the Li et al.59 method. The Coats57 method (Eqs. 5.93 and 5.94) is always recommended for calculating pseudocomponent properties. References 1. Yarborough, L.: “Application of a Generalized Equation of State to Petroleum Reservoir Fluids,” Equations of State in Engineering and Research, K.C. Chao and R.L. Robinson Jr. (eds.), Advances in Chemistry Series, American Chemical Soc., Washington, DC (1978) 182, 386. 2. Whitson, C.H.: “Characterizing Hydrocarbon Plus Fractions,” SPEJ (August 1983) 683; Trans., AIME, 275. 3. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “SRK-EOS Calculation for Crude Oils,” Fluid Phase Equilibria (1983) 14, 209. 4. Craft, B.C., Hawkins, M., and Terry, R.E.: Applied Petroleum Reservoir Engineering, second edition, Prentice-Hall Inc., Englewood Cliffs, New Jersey (1991). 5. McCain, W.D. Jr.: The Properties of Petroleum Fluids, second edition, PennWell Publishing Co., Tulsa, Oklahoma (1990). 6. Katz, D.L. and Firoozabadi, A.: “Predicting Phase Behavior of Condensate/Crude-Oil Systems Using Methane Interaction Coefficients,” JPT (November 1978) 1649; Trans., AIME, 265. 7. Austad, T. et al.: “Practical Aspects of Characterizing Petroleum Fluids,” paper presented at the 1983 North Sea Condensate Reservoirs and Their Development Conference, London, 24–25 May. 8. Chorn, L.G.: “Simulated Distillation of Petroleum Crude Oil by Gas Chromatography—Characterizing the Heptanes-Plus Fraction,” J. Chrom. Sci. (January 1984) 17. 9. MacAllister, D.J. and DeRuiter, R.A.: “Further Development and Application of Simulated Distillation for Enhanced Oil Recovery,” paper SPE 14335 presented at the 1985 SPE Annual Technical Conference and Exhibition, Las Vegas, Nevada, 22–25 September. 10. Designation D158, Saybolt Distillation of Crude Petroleum, Annual Book of ASTM Standards, ASTM, Philadelphia, Pennsylvania (1984). 11. Designation D2892-84, Distillation of Crude Petroleum (15.Theoretical Plate Column), Annual Book of ASTM Standards, ASTM, Philadelphia, Pennsylvania (1984) 8210. 12. Kesler, M.G. and Lee, B.I.: “Improve Predictions of Enthalpy of Fractions,” Hydro. Proc. (March 1976) 55, 153. 13. Lee, B.I. and Kesler, M.G.: “A Generalized Thermodynamic Correlation Based on Three-Parameter Corresponding States,” AIChE J. (1975) 21, 510. 14. Riazi, M.R. and Daubert, T.E.: “Simplify Property Predictions,” Hydro. Proc. (March 1980) 115. 15. Maddox, R.N. and Erbar, J.H.: Gas Conditioning and Processing—Advanced Techniques and Applications, Campbell Petroleum Series, Norman, Oklahoma (1982) 3. 16. Organick, E.I. and Golding, B.H.: “Prediction of Saturation Pressures for Condensate-Gas and Volatile-Oil Mixtures,” Trans., AIME (1952) 195, 135. 17. Katz, D.L. et al.: Handbook of Natural Gas Engineering, McGraw-Hill Book Co. Inc., New York City (1959). 18. Riazi, M.R. and Daubert, T.E.: “Analytical Correlations Interconvert Distillation-Curve Types,” Oil & Gas J. (August 1986) 50. 19. Riazi, M.R. and Daubert, T.E.: “Characterization Parameters for Petroleum Fractions,” Ind. Eng. Chem. Res. (1987) 26, 755. 20. Robinson, D.B. and Peng, D.Y.: “The Characterization of the Heptanes and Heavier Fractions,” Research Report 28, Gas Producers Assn., Tulsa, Oklahoma (1978). 21. Riazi, M.R. and Daubert, T.E.: “Prediction of the Composition of Petroleum Fractions,” Ind. Eng. Chem. Proc. Des. Dev. (1980) 19, 289. 22. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “Thermodynamics of Petroleum Mixtures Containing Heavy Hydrocarbons. 1. Phase Envelope Calculations by Use of the Soave-Redlich-Kwong Equation of State,” Ind. Eng. Chem. Proc. Des. Dev. (1984) 23, 163. 23. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “Thermodynamics of Petroleum Mixtures Containing Heavy Hydrocarbons. 2. Flash and PVT Calculations with the SRK Equation of State,” Ind. Eng. Chem. Proc. Des. Dev. (1984) 23, 566. 24. Lohrenz, J., Bray, B.G., and Clark, C.R.: “Calculating Viscosities of Reservoir Fluids From Their Compositions,” JPT (October 1964) 1171; Trans., AIME, 231. HEPTANES-PLUS CHARACTERIZATION
25. Whitson, C.H.: “Effect of C7) Properties on Equation-of-State Predictions,” paper SPE 11200 presented at the 1982 SPE Annual Technical Conference and Exhibition, New Orleans, 26–29 September. 26. Whitson, C.H.: “Effect of C7) Properties on Equation-of-State Predictions,” SPEJ (December 1984) 685; Trans., AIME, 277. 27. Whitson, C.H., Andersen, T.F., and Søreide, I.: “C7) Characterization of Related Equilibrium Fluids Using the Gamma Distribution,” C7 ) Fraction Characterization, L.G. Chorn and G.A. Mansoori (eds.), Advances in Thermodynamics, Taylor & Francis, New York City (1989) 1, 35–56. 28. Brulé, M.R., Kumar, K.H., and Watansiri, S.: “Characterization Methods Improve Phase-Behavior Predictions,” Oil & Gas J. (11 February 1985) 87. 29. Hoffmann, A.E., Crump, J.S., and Hocott, C.R.: “Equilibrium Constants for a Gas-Condensate System,” Trans., AIME (1953) 198, 1. 30. Abramowitz, M. and Stegun, I.A.: Handbook of Mathematical Functions, Dover Publications Inc., New York City (1970) 923. 31. Haaland, S.: “Characterization of North Sea Crude Oils and Petroleum Fractions,” MS thesis, Norwegian Inst. of Technology, Trondheim, Norway (1981). 32. Watson, K.M., Nelson, E.F., and Murphy, G.B.: “Characterization of Petroleum Fractions,” Ind. Eng. Chem. (1935) 27, 1460. 33. Watson, K.M. and Nelson, E.F.: “Improved Methods for Approximating Critical and Thermal Properties of Petroleum,” Ind. Eng. Chem. (1933) 25, No. 8, 880. 34. Jacoby, R.H. and Rzasa, M.J.: “Equilibrium Vaporization Ratios for Nitrogen, Methane, Carbon Dioxide, Ethane, and Hydrogen Sulfide in Absorber Oil/Natural Gas and Crude Oil/Natural Gas Systems,” Trans., AIME (1952) 195, 99. 35. Søreide, I.: “Improved Phase Behavior Predictions of Petroleum Reservoir Fluids From a Cubic Equation of State,” Dr.Ing. dissertation, Norwegian Inst. of Technology, Trondheim, Norway (1989). 36. Technical Data Book—Petroleum Refining, third edition, API, New York City (1977). 37. Rao, V.K. and Bardon, M.F.: “Estimating the Molecular Weight of Petroleum Fractions,” Ind. Eng. Chem. Proc. Des. Dev. (1985) 24, 498. 38. Benedict, M., Webb, G.B., and Rubin, L.C.: “An Empirical Equation for Thermodynamic Properties of Light Hydrocarbons and Their Mixtures, I. Methane, Ethane, Propane, and n-Butane,” J. Chem. Phys. (1940) 8, 334. 39. Reid, R.C.: “Present, Past, and Future Property Estimation Techniques,” Chem. Eng. Prog. (1968) 64, No. 5, 1. 40. Reid, R.C., Prausnitz, J.M., and Polling, B.E.: The Properties of Gases and Liquids, fourth edition, McGraw-Hill Book Co. Inc., New York City (1987) 12–24. 41. Roess, L.C.: “Determination of Critical Temperature and Pressure of Petroleum Fractions,” J. Inst. Pet. Tech. (October 1936) 22, 1270. 42. Cavett, R.H.: “Physical Data for Distillation Calculations-Vapor-Liquid Equilibria,” Proc., 27th API Meeting, San Francisco (1962) 351. 43. Nokay, R.: “Estimate Petrochemical Properties,” Chem. Eng. (23 February 1959) 147. 44. Pitzer, K.S. et al.: “The Volumetric and Thermodynamic Properties of Fluids, II. Compressibility Factor, Vapor Pressure, and Entropy of Vaporization,” J. Amer. Chem. Soc. (1955) 77, No. 13, 3433. 45. Edmister, W.C.: “Applied Hydrocarbon Thermodynamics, Part 4: Compressibility Factors and Equations of State,” Pet. Ref. (April 1958) 37, 173. 46. Hall, K.R. and Yarborough, L.: “New, Simple Correlation for Predicting Critical Volume,” Chem. Eng. (November 1971) 76. 47. Kesler, M.G., Lee, B.I., and Sandler, S.I.: “A Third Parameter for Use in Generalized Thermodynamic Correlations,” Ind. Eng. Chem. Fund. (1979) 18, No. 1, 49. 48. Twu, C.H.: “An Internally Consistent Correlation for Predicting the Critical Properties and Molecular Weights of Petroleum and Coal-Tar Liquids,” Fluid Phase Equilibria (1984) No. 16, 137. 49. Peng, D.Y. and Robinson, D.B.: “A New-Constant Equation of State,” Ind. Eng. Chem. Fund. (1976) 15, No. 1, 59. 50. Whitson, C.H.: “Critical Properties Estimation From an Equation of State,” paper SPE 12634 presented at the 1984 SPE/DOE Symposium on Enhanced Oil Recovery, Tulsa, Oklahoma, 15–18 April. 51. Brulé, M.R. and Starling, K.E.: “Thermophysical Properties of Complex Systems: Applications of Multiproperty Analysis,” Ind. Eng. Chem. Proc. Des. Dev. (1984) 23, 833. 19
52. Peneloux, A., Rauzy, E., and Freze, R.: “A Consistent Correction for Redlich-Kwong-Soave Volumes,” Fluid Phase Equilibria (1982) 8, 7. 53. Jhaveri, B.S. and Youngren, G.K.: “Three-Parameter Modification of the Peng-Robinson Equation of State To Improve Volumetric Predictions,” SPERE (August 1988) 1033; Trans., AIME, 285. 54. Chueh, P.L. and Prausnitz, J.M.: “Calculation of High-Pressure Vapor– Liquid Equilibria,” Ind. Eng. Chem. (1968) 60, No. 13. 55. Pedersen, K.S., Thomassen, P., and Fredenslund, A.: “Characterization of Gas Condensate Mixtures,” C7) Fraction Characterization, L.G. Chorn and G.A. Mansoori (eds.), Advances in Thermodynamics, Taylor & Francis, New York City (1989) 1. 56. Zudkevitch, D. and Joffe, J: “Correlation and Prediction of Vapor-Liquid Equilibrium with the Redlich-Kwong Equation of State,” AIChE J. (1970) 16, 112. 57. Coats, K.H.: “Simulation of Gas-Condensate-Reservoir Performance,” JPT (October 1985) 1870. 58. Lee, S.T. et al.: “Experiments and Theoretical Simulation on the Fluid Properties Required for Simulation of Thermal Processes,” SPEJ (October 1982) 535. 59. Li, Y.-K., Nghiem, L.X., and Siu, A.: “Phase Behavior Computation for Reservoir Fluid: Effects of Pseudo Component on Phase Diagrams and Simulations Results,” paper CIM 84-35-19 presented at the 1984 Petroleum Soc. of CIM Annual Meeting, Calgary, 10–13 June.
20
60. Newley, T.M.J. and Merrill, R.C. Jr.: “Pseudocomponent Selection for Compositional Simulation,” SPERE (November 1991) 490; Trans., AIME, 291. 61. Schlijper, A.G.: “Simulation of Compositional Processes: The Use of Pseudocomponents in Equation-of-State Calculations,” SPERE (September 1986) 441; Trans., AIME, 282. 62. Behrens, R.A. and Sandler, S.I.: “The Use of Semicontinuous Description To Model the C7) Fraction in Equation of State Calculations,” paper SPE 14925 presented at the 1986 SPE/DOE Symposium on Enhanced Oil Recovery, Tulsa, Oklahoma, 23–23 April. 63. Wu, R.S. and Batycky, J.P.: “Pseudocomponent Characterization for Hydrocarbon Miscible Displacement,” paper SPE 15404 presented at the 1986 SPE Annual Technical Conference and Exhibition, New Orleans, 5–6 October. 64. Kay, W.B.: “The Ethane-Heptane System,” Ind. & Eng. Chem. (1938) 30, 459.
SI Metric Conversion Factors ft3/lbm mol 6.242 796 °F (°F*32)/1.8 °F (°F)459.67)/1.8 psi 6.894 757 °R 5/9
E*02 +m3/kmol +°C +K E)00 +kPa +K
PHASE BEHAVIOR
Chapter 6
Conventional PVT Measurements 6.1 Introduction This chapter reviews the standard experiments performed by pressure/volume/temperature (PVT) laboratories on reservoir fluid samples: compositional analysis, multistage surface separation, constant composition expansion (CCE), differential liberation expansion (DLE), and constant volume depletion (CVD). We present data from actual laboratory reports and give methods for checking the consistency of reported data for each experiment. Chaps. 5 and 8 discuss special laboratory studies, including true-boiling-point (TBP) distillation and multicontact gas-injection tests, respectively. Table 6.1 summarizes experiments typically performed on oils and gas condensates. From this table, we see that the DLE experiment is the only test never performed on gas-condensate systems. We begin by discussing standard analyses performed on oil and gascondensate samples. 6.1.1 General Information Sheet. Most commercial laboratories report general information on a cover sheet of the laboratory report, including formation and well characteristics and sampling conditions. Tables 6.2 and 6.31,2 show this information, which may be important for correct application and interpretation of the fluid analyses. This is particularly true for wells where separator samples must be recombined to give a representative wellstream composition. Most of these data are supplied by the contractor of the fluid study and are recorded during sampling. Therefore, the representative for the company contracting the fluid study is responsible for the correctness and completeness of reported data. We strongly recommend that the following data always be reported in a general information sheet: (1) separator gas/oil ratio (GOR) in standard cubic feet/separator barrel, (2) separator conditions at sampling, (3) field shrinkage factor used ( + B osp), (4) flowing bottomhole pressure (FBHP) at sampling, (5) static reservoir pressure, (6) minimum FBHP before and during sampling, (7) time and date of sampling, (8) production rates during sampling, (9) dimensions of sample container, (10) total number and types of samples collected during the drillstem test, and (11) perforation intervals. 6.1.2 Oil PVT Analyses. Standard PVT analyses performed on reservoir oils usually include (1) bottomhole wellstream compositional analysis through C 7), (2) CCE, (3) DLE, and (4) multistage-separator tests. The CCE experiment determines the bubblepoint pressure and volumetric properties of the undersaturated oil. It also gives two-phase volumetric behavior below the bubblepoint; however, these data are rarely used. The DLE experiment and separator test are used together to calculate traditional black-oil properties, B o and R s, for reservoir-engineering calculations. Occasionally, 88
instead of a DLE study, a CVD experiment is run on a volatile oil. Also, the C 7) fraction may be separated into single-carbon-number cuts from C 7 through approximately C 20) by TBP analysis or simulated distillation (see Chap. 5). 6.1.3 Gas-Condensate PVT Analyses. The standard experimental program for a gas-condensate fluid includes (1) recombined wellstream compositional analysis through C 7), (2) CCE, and (3) CVD. The CCE and CVD data are measured in a high-pressure visual cell where the dewpoint pressure is determined visually. Total volume/ pressure and liquid-dropout behavior is measured in the CCE experiment. Phase volumes defining retrograde behavior are measured in the CVD experiment together with Z factors and produced-gas compositions through C 7). Optionally, a multistageseparator test can be performed as well as TBP analysis or simulated distillation of the C 7) into single-carbon-number cuts from C 7 to about C 20) (see Chap. 5). 6.2 Wellstream Compositions PVT studies usually are based on one or more samples taken during a production test. Bottomhole samples can be obtained by wireline with a high-pressure container during either production testing or a shut-in period. Alternatively, separator samples can be taken during a production test. Bottomhole sampling is the preferred method for most oil reservoirs, while recombined samples are traditionally used for gas-condensate reservoirs.3-8 Taking both bottomhole and separator samples in oil wells is not uncommon. The advantage of separator samples is that they can be recombined in varying proportions to achieve a desired bubblepoint pressure (e.g., initial reservoir pressure); these larger samples are needed for special PVT tests (e.g., TBP and slim tube among others). 6.2.1 Bottomhole Sample. Table 6.4 shows the reported wellstream composition of a reservoir oil where C 7) specific gravity and molecular weight are also reported. In the example report, composition is given both as mole and weight percent although many laboratories report only molar composition. Experimentally, the composition of a bottomhole sample is determined by the following (Fig. 6.1). 1. Flashing the sample to atmospheric conditions. 2. Measuring the volumes of surface gas, V g , and surface oil, V o . 3. Determining the normalized weight fractions, w gi and w oi, of surface samples by gas chromatography. 4. Measuring surface-oil molecular weight, M o , and specific gravity, g o . PHASE BEHAVIOR
TABLE 6.1—LABORATORY ANALYSES PERFORMED ON RESERVOIR-OIL AND GAS-CONDENSATE SYSTEMS
TABLE 6.2—EXAMPLE GENERAL INFORMATION SHEET FOR GOOD OIL CO. WELL 4 OIL SAMPLE
Laboratory Analysis
Oils
Gas Condensates
Bottomhole sample
D
d
Recombined composition
d
D
First well completed
C7+ TBP distillation
d
d
Original reservoir pressure at 8,692 ft, psig
C7+ simulated distillation
d
d
Original produced GOR, scf/bbl
Constant-composition expansion
D
D
Production rate, B/D
Multistage surface separation
D
d
Differential liberation
D
Separator temperature, °F
N
Separator pressure, psig
CVD
d
D
Multicontact gas injection
d
d
D+standard, d+can be performed, and N+not performed.
z i + F g y i ) (1 * F g) x i ; . . . . . . . . . . . . . . . . . . . . . . . . (6.1) 1 , . . . . . . . . . . . . . . . . . . (6.2) 1 ) ƪ133, 300ǒ gńM Ǔ ońR sƫ
where R s +GOR V gńV o in scf/STB from the single-stage flash; yi +
ȍ ǒw
ǒ
ńM jǓ ) w g C
j0C 7)
xi +
7)
7)
w o ińM i
ǒ
ńM jǓ ) w o C
oj
j0C 7)
+
7)
ńM g C
Ǔ
; . . . . . . . . . (6.3)
wo C ǒ1ńM Ǔ * o
7)
7)
ȍ ǒw
ńM o C
7)
Ǔ
;
600 300 75 200
Oil gravity at 60°F, °API Datum
8,000 No Well Characteristics
Elevation, ft
610
Total depth, ft
8,943
Producing interval, ft
8,684 to 8,700
Tubing size, in.
27/8
Tubing depth, ft
8,600
PI at 300 B/D, B-D/psi
1.1
Last reservoir pressure at 8,500 ft, psig
3,954* / /19
Reservoir temperature at 8,500 ft, °F
Shut in 72 hours Amerada
Normal production rate, B/D
300
GOR, scf/bbl
600
Separator pressure, psig
200
Separator temperature, °F
Ǔ
ojńM j
. . . . . . . . . . . . . . (6.5)
j0C 7)
Surface gas usually contains less than 1 mol% C 7) material consisting mainly of heptanes and octanes; M g C + 105 is usually a 7) good assumption. Surface oil contains less than 1 mol% of the light constituents C 1, C 2, and nonhydrocarbons. Low-temperature distillation can be used to improve the accuracy of reported weight fractions for intermediate components in the surface oil ( C 3 through C 6); however, gas chromatography is more widely used. The most probable source of error in wellstream composition of a bottomhole sample is the surface-oil molecular weight, M o , which appears in Eq. 6.2 for F g and Eq. 6.4 for x i . M o is usually accurate within "4 to 10%. In Chap. 5, we showed that the Watson characterization factor, K w, of surface oil (Eq. 5.35) should be constant (to within "0.03 of the determined value) for a given reservoir. Once an average has been established for a reservoir (usually requiring three separate measurements), potential errors in M o can be checked. A calculated K w that deviates from the field-average K w by more than "0.03 may indicate an erroneous molecular-weight measurement. Eqs. 6.1 through 6.4 show that all component compositions are affected by M o C , which is backcalculated from M o with Eq. 7) 6.5. Fortunately, the amount of lighter components (particularly C 1) in the surface oil are small, so the real effect on conversion from weight to mole fractions of the surface oil usually is not significant. 6.2.2 Recombined Samples. Tables 6.5 and 6.6 present the separator-oil and -gas compositional analyses of a gas-condensate fluid and recombined wellstream composition. The separator-oil composition is obtained by use of the same procedure as that used for bottomhole oil samples (Eqs. 6.1 through 6.5). This involves bringing the separator oil to standard conditions, measuring properties CONVENTIONAL PVT MEASUREMENTS
(m/d/y) 217*
Well status
. . . . . . . . . . (6.4)
(m/d/y) 4,100
Pressure gauge
ȍ ǒw
and M o C
/ /19
Date
wg i ń Mi gj
Cretaceous
Original gas cap
5. Converting w gi weight fractions to normalized mole fractions y i and x i . 6. Recombining mathematically to the wellstream composition, z i. Eqs. 6.1 through 6.5 give Steps 1 through 6 mathematically.
Fg +
Formation Characteristics Name
75
Base pressure, psia
14.65
Well making water, % water cut
0
Sampling Conditions Sample depth, ft
8,500
Well status
Shut in 72 hours
GOR Separator pressure, psig Separator temperature, °F Tubing pressure, psig
1,400
Casing pressure, psig Sampled by Sampler type
Wofford
*Pressure and temperature extrapolated to the midpoint of the producing interval+4,010 psig and 220°F.
and compositions of the resulting surface oil and gas, and recombining these compositions to give the separator-oil composition; Tables 6.5 and 6.6 report the results. Separator gas is introduced directly into a gas chromatograph, which yields weight fractions, w g . These weight fractions are converted to mole fractions, y i , by use of appropriate molecular weights; Tables 6.5 and 6.6 show the results. C 7) molecular weight is backcalculated with measured separator-gas specific gravity, g g .
Mg C
7)
+ w gC
7)
ǒ
1 * 28.97g g
Ǔ
*1
ȍ
wg i Mi
i0C 7)
. . . . . . . . (6.6)
89
TABLE 6.3—EXAMPLE GENERAL INFORMATION SHEET FOR GOOD OIL CO. WELL 7 GAS CONDENSATE Formation Characteristics Formation name
Pay sand
Date first well completed
/ /19
Original reservoir pressure at 10,148 ft, psig
(m/d/y) 5,713
Original produced-gas/liquid ratio, scf/bbl Production rate, B/D Separator pressure, psig Separator temperature, °F Liquid gravity at 60°F, °API Datum, ft subsea
8,000 Well Characteristics
Elevation, ft KB
2,214
Total depth, ft
10,348
Producing interval, ft
10,124 to 10,176
Tubing size, in.
2
Tubing depth, ft
10,100
Open-flow potential, MMscf/D Last reservoir pressure at 10,148 ft, psig
5,713
Date
/ /19
Reservoir temperature at 10,148 ft, °F
(m/d/y) 186
Status of well status
Shut in
Pressure gauge
Amerada Sampling Conditions
Flowing tubing pressure, psig
3,375
FBHP, psig
5,500
Primary-separator pressure, psig
300
Primary-separator temperature, °F
62
Secondary-separator pressure, psig
20
Secondary-separator temperature, °F
60
Field stock-tank-liquid gravity at 60°F, °API
58.5
Primary-separator-gas production rate, Mscf/D
762.14
Pressure base, psia
14.696
Temperature base, °F
60
Compressibility factor, Fpv
1.043
Gas gravity (laboratory)
0.737
Gas-gravity factor, Fg
0.902
Stock-tank-liquid production rate at 60°F, B/D
127.3
Primary-separator-gas/stock-tank-liquid ratio In scf/bbl In bbl/MMscf
5,987 167.0
Sampled by
For the example PVT report (Tables 6.5 and 6.6), the separator gas/oil ratio, R sp, during sampling is reported as standard gas volume per separator-oil volume (4,428 scf/bbl). In this report, the units are incorrectly labeled scf/bbl at 60°F, where in fact the separator-oil volume is measured at separator pressure (300 psig) and temperature (62°F). The separator-oil formation volume factor (FVF), B osp, is 1.352 bbl/STB and represents the volume of separator oil required to yield 1 STB of oil (i.e., condensate). The equation used to calculate wellstream composition, z i, is z i + F gsp y i ) (1 * F gsp) x i ,
ǒ
F gsp + 1 )
2, 130ò osp M osp R sp
Ǔ
*1
, . . . . . . . . . . . . . . . . . . . . . (6.8)
ȍx M . . . . . . . . . . . . . . . . . . . . . . . . . . . . N
where M osp +
i
i
(6.9)
i+1
. . . . . . . . . . . . . . . . . . . . . (6.7)
where F gsp +mole fraction of wellstream mixture that becomes separator gas. In the laboratory report, F gsp is reported as “primary90
separator gas/wellstream ratio” (801.66 Mscf/MMscf), which is equivalent to mole per mole ( F gsp +0.80166 mol/mol). The reported value of F gsp can be checked with
ò osp in lbm/ft3 is calculated with a correlation (e.g., Standing-Katz9) or with the relation (62.4g o ) 0.0136g g R s)ńB o , where R s and B o +separator-oil values in scf/STB and bbl/STB, respectively; PHASE BEHAVIOR
TABLE 6.4—WELLSTREAM (RESERVOIR-FLUID) COMPOSITION FOR GOOD OIL CO. WELL 4 BOTTOMHOLE OIL SAMPLE Component H2 S CO2 N2 Methane Ethane Propane i-butane n-butane i-pentane n-pentane Hexanes Heptanes plus Total
mol% Nil 0.91 0.16 36.47 9.67 6.95 1.44 3.93 1.44 1.41 4.33 33.29 100.00
wt% Nil 0.43 0.05 6.24 3.10 3.27 0.89 2.44 1.11 1.09 3.97 77.41 100.00
Density* (g/cm3)
°API*
Molecular Weight
DV g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.11) V osp
D R sp +
0.8515
34.5
218
and D R s +
DV g . Vo
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.12)
Total GOR is calculated by adding the stock-tank-oil-based GOR’s from each separator stage.
*At 60°F.
g o +stock-tank-oil density; and g g +gravity of gas released from the separator oil. Finally, the value of stock-tank-liquid/wellstream ratio in bbl/MMscf represents the separator barrels produced per 1 MMscf of wellstream. In terms of F gsp and separator properties, this value equals
ǒ
removed gas, n g ; and specific gravity of removed gas, g g. If requested, the gas samples can be analyzed chromatographically to give molar composition, y. The oil remaining after gas removal is brought to the conditions of the next separator stage. The gas is removed again and quantified by moles and specific gravity. Oil volume is noted, and the process is repeated until stock-tank conditions are reached. Final oil volume, V o , and specific gravity, g o , are measured at 60°F. Table 6.7 gives results from four separator tests, each consisting of two stages of separation. The first-stage-separator pressure is varied from 50 to 300 psig, and stock-tank conditions are held constant at 0 psig and 75°F. GOR’s are reported as standard gas volume per separator-oil volume, R sp, and as standard gas volume per stocktank-oil volume, R s, respectively.
Ǔ
bbl + 470(1*F gsp) M ospńò osp , . . . . . . . . . . . . . . (6.10) B osp MMscf where 470+(1 million scf/MMscf)/[(379 scf/lbm mol)(5.615 ft3/bbl)]. The separator-oil and -gas compositions can be checked for consistency with the Hoffman et al.10 K-value method and Standing’s11 low-pressure K-value equations. 6.3 MultistageĆSeparator Test The multistage-separator test is performed on an oil sample primarily to provide a basis for converting differential-liberation data from a residual-oil to a stock-tank-oil basis. Occasionally, several separator tests are run to help choose separator conditions that maximize stock-tank-oil production. Usually, two or three stages of separation are used, with the last stage at atmospheric pressure and near-ambient temperature (60 to 80°F). The multistage-separator test can also be conducted for high-liquid-yield gas-condensate fluids. Fig. 6.2 illustrates schematically how the separator test is performed. Initially, the reservoir sample is at saturation conditions and the volume is measured ( V ob or V gd ). The sample is then brought to the pressure and temperature of the first-stage separator. All the gas is removed, and the oil volume at the separator stage, V osp, is noted together with the volume of removed gas, DV g ; number of moles of
N sp
Rs +
ȍǒD R Ǔ
s k
.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.13)
k+1
Separator-oil FVF’s, B osp, are reported as the ratio of separator-oil volume to stock-tank-oil volume. B osp +
V osp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.14) Vo
Accordingly, the relation between separator gas/oil ratio and stocktank gas/oil ratio at a given stage is D Rs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.15) B osp
D R sp +
Because B osp u 1, it follows that R sp t R s. Bubblepoint-oil FVF, B ob , is the ratio of bubblepoint-oil volume to stock-tank-oil volume. B ob +
V ob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.16) Vo
The average gas gravity, g g , is used in oil PVT correlations and to calculate reservoir densities on the basis of black-oil properties. The average gas gravity is calculated from N sp
ȍǒ g Ǔ ǒD R Ǔ g k
gg +
s k
k+1 N sp
ȍǒD R Ǔ
, . . . . . . . . . . . . . . . . . . . . . . . . . . (6.17)
s k
k+1
Fig. 6.1—Procedure for recombining single-stage separator samples to obtain wellstream composition of a bottomhole sample; BHS + bottomhole sampler, GC + gas chromatograph, FDP + freezing-point depression, and DM + densitometer. CONVENTIONAL PVT MEASUREMENTS
91
TABLE 6.5—SEPARATOR AND RECOMBINED WELLSTREAM COMPOSITIONS FOR GOOD OIL CO. WELL 7 GAS CONDENSATE Separator Products Hydrocarbon Analysis Separator Liquid Component
(mol%)
CO2
Trace
N2
Separator Gas (mol%)
(gal/Mscf)
0.22
Wellstream (mol%)
(gal/Mscf)
0.18
Trace
0.16
0.13
Methane
7.78
75.31
61.92
Ethane
10.02
15.08
Propane
15.08
6.68
1.832
14.08 8.35
2.290
iso-butane
2.77
0.52
0.170
0.97
0.317
n-butane
11.39
1.44
0.453
3.41
1.073
iso-pentane
3.52
0.18
0.066
0.84
0.306
n-pentane
6.50
0.24
0.087
1.48
0.535
Hexanes
8.61
0.11
0.045
1.79
0.734
34.33
0.06
0.028
6.85
3.904
100.00
100.00
2.681
100.00
9.159
Heptanes plus Total
Heptanes-Plus Properties Oil gravity, °API
46.6
Specific gravity at 60/60°F
0.7946
Molecular weight
0.795
143
103
143
Parameters Calculated separator gas gravity (air+1.000)
0.735
Calculated gross heating value for separator gas at 14.696 psia and 60°F, BTU/ft3 dry gas
1,295
Primary-separator-gas*/-separator-liquid* ratio, scf/bbl at 60°F
4,428
Primary-separator-gas/stock-tank-liquid ratio at 60°F, bbl at 60°F/bbl
1.352
Primary-separator-gas/wellstream ratio, Mscf/MMscf
801.66
Stock-tank-liquid/wellstream ratio, bbl/MMscf
133.9
*Primary separator gas and liquid collected at 300 psig and 62°F.
TABLE 6.6—MATERIAL-BALANCE CALCULATIONS FOR GOOD OIL CO. WELL 7 GAS-CONDENSATE SAMPLE Liquid Composition at Specified Pressures (mol%) Component
At 3,500 psig
At 2,900 psig
At 2,100 psig
At 1,300 psig
At 605 psig
CO2
0.18
0.18
0.18
0.15
0.08
N2
0.13
0.08
0.06
0.03
0.01
C1
13.18
45.04
32.22
19.69
11.77
C2
8.12
14.05
13.99
12.32
7.44
C3
12.59
9.67
11.25
11.66
9.31
i-C4
3.44
1.14
1.59
1.85
1.64
n-C4
5.21
4.82
6.12
7.35
7.17
i-C5
2.67
1.25
1.77
2.43
2.79
n-C5
5.74
2.16
3.48
4.62
5.50
C6
8.47
3.11
4.55
6.40
8.37
C7+ Total M o, gńmol M oC 7), gńmol ò o, gńcm 3 92
40.27
18.51
24.79
33.50
45.91
100.00
100.00
100.00
100.00
100.00
96.6
54.1
64.3
78.2
95.6
168.8
160.1
152.1
149.9
150.3
0.3235
0.2642
0.1625
0.0892
0.0398 PHASE BEHAVIOR
where M i +molecular weight and ò i + component liquid density in lbm/ft3 at standard conditions (Table A-1). The C 7) material in separator gases is usually treated as normal heptane. 6.4 Constant Composition Expansion
pst+14.7 psia Tst+60°F Fig. 6.2—Schematic of a multistage-separator test.
where ǒg gǓ k +separator-gas gravity at Stage k. This relation is based on the ideal gas law at standard conditions, where moles of gas are directly proportional with standard gas volume ( v g +379 scf/lbm mol). Table 6.8 gives the composition of the first-stage-separator gas at 50 psig and 75°F. The gross heating value, H g , of this gas is calculated by Kay’s12 mixing rule and component heating values, H i, given in Table A-1.
ȍy H . N
Hg +
i
i
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.18)
i+1
Component liquid yields, L i , represent the liquid volumes of a component or group of components that can theoretically be processed from 1 Mscf of separator gas (gallons per million standard cubic feet). Li can be calculated from
ǒ Ǔ
M L i + 19.73y i ò i , . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.19) i
6.4.1 Oil Samples. For an oil sample, the CCE experiment is used to determine bubblepoint pressure, undersaturated-oil density, isothermal oil compressibility, and two-phase volumetric behavior at pressures below the bubblepoint. Table 6.9 presents data from an example CCE experiment for a reservoir oil. Fig. 6.3 illustrates the procedure for the CCE experiment. A blind cell (i.e., a cell without a window) is filled with a known mass of reservoir fluid. Reservoir temperature is held constant during the experiment. The sample initially is brought to a condition somewhat above initial reservoir pressure, ensuring that the fluid is single phase. As the pressure is lowered, oil volume expands and is recorded. The fluid is agitated at each pressure by rotating the cell. This avoids the phenomenon of supersaturation, or metastable equilibrium, where a mixture remains as a single phase even though it should exist as two phases.13-15 Sometimes supersaturation occurs 50 to 100 psi below actual bubblepoint pressure. By agitating the mixture at each new pressure, the condition of supersaturation is avoided, allowing more accurate determination of the bubblepoint. Just below the bubblepoint, the measured volume will increase more rapidly because gas evolves from the oil, yielding a higher system compressibility. The total volume, V t, is recorded after the twophase mixture is brought to equilibrium. Pressure is lowered in steps of 5 to 200 psi, where equilibrium is obtained at each pressure. When the lowest pressure is reached, total volume is three to five times larger than the original bubblepoint volume. The recorded cell volumes are plotted vs. pressure, and the resulting curve should be similar to one of the curves in Fig. 6.4.16 For a black oil (far from its critical temperature), the discontinuity in volume at the bubblepoint is sharp and the bubblepoint pressure and volume are easily read from the intersection of the p-V trends in the single- and two-phase regions. Volatile oils do not exhibit the same clear discontinuity in volumetric behavior at the bubblepoint pressure. Instead, the p-V curve is practically continuous in the region of the bubblepoint because the undersaturated-oil compressibility is similar to the effective two-phase compressibility. This makes determining the bubblepoint of volatile oils in a blind cell difficult. Instead, a windowed cell
TABLE 6.7—SEPARATOR TESTS (RESERVOIR-FLUID) OF GOOD OIL CO. WELL 4 OIL SAMPLE Separator Pressure (psia)
Separator Temperature (°F)
GORb (ft3/bbl)
GORc (ft3/bbl)
50 to 0
75
715
737
75
41
41
100 to 0
75
637
676
75
91
92
200 to 0
75
542
602
75
177
178
300 to 0
75
478
549
75
245
246
Stock-Tank Gravity (°API)
40.5
40.7
40.4
40.1
FVFd (bbl/bbl)
1.481
1.474
1.483
1.495
aGauge. bIn cubic feet of gas at 60°F and 14.65 psi absolute per barrel of oil at indicated pressure and cIn cubic feet of gas at 60°F and 14.65 psi absolute per barrel of stock-tank oil at 60°F. dIn barrels of saturated oil at 2,620 psi gauge and 220°F per barrel of stock-tank oil at 60°F. eIn barrels of oil at indicated pressure and temperature per barrel of stock-tank oil at 60°F.
CONVENTIONAL PVT MEASUREMENTS
Separator Volume Factore (bbl/bbl)
Flashed-Gas Specific Gravity
1.031
0.840
1.007
1.338
1.062
0.786
1.007
1.363
1.112
0.732
1.007
1.329
1.148
0.704
1.007
1.286
temperature.
93
TABLE 6.8—FIRST-STAGE SEPARATOR-GAS COMPOSITION AND GROSS HEATING VALUE FOR GOOD OIL CO. WELL 4 OIL SAMPLE* Component
mol%
gal/Mscf
H2 S
Nil
CO2
1.62
N2
0.30
C1
67.00
C2
16.04
4.265
C3
8.95
2.449
i-C4
1.29
0.420
n-C4
2.91
0.912
i-C5
0.53
0.193
n-C5
0.41
0.155
C6
0.44
0.178
C7+
0.49
0.221
Total
100.00
TABLE 6.9—CCE DATA (RESERVOIR-FLUID) FOR GOOD OIL CO. WELL 4 OIL SAMPLE Saturation (bubblepoint) pressure*, psig
0.02441
Thermal expansion of undersaturated oil at 5,000 psi+V at 220°F/V at 76°F
1.08790
Compressibility of saturated oil at reservoir temperature From 5,000 to 4,000 psi, vol/vol-psi From 4,000 to 3,000 psi, vol/vol-psi From 3,000 to 2,620 psi, vol/vol-psi
Calculated gross heating value,
BTU/ft3
8.793 0.840 1,405
dry gas at 14.65 psia and 60°F *Collected at 50 psig and 75°F in the laboratory.
is used to observe visually the first bubble of gas and the liquid volumes below the bubblepoint. Reported data from commercial laboratories usually include bubblepoint pressure, p b ; bubblepoint density, ò ob, or specific volume, v ob(v + 1ńò); and isothermal compressibility of the undersaturated oil, co , at pressures above the bubblepoint (Table 6.9). The table also shows the oil’s thermal expansion, indicated by a ratio of undersaturated-oil volume at a specific pressure and reservoir temperature to the oil volume at the same pressure and a lower temperature. Total volumes are reported relative to the bubblepoint volume. V rt +
Vt . V ob
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.20)
Traditionally, isothermal compressibility data are reported for pressure intervals above the bubblepoint. In fact, the undersaturated-oil compressibility varies continuously with pressure, and, because V t + V o (V rt + V ro) for p u p b, oil compressibility can be expressed as
ǒ Ǔ
ēV rt c+ 1 V rt ēp
ǒ Ǔ;
ēV ro + 1 ēp V ro T
p u p b . . . . . . . . . . (6.21)
T
13.48 x 10 – 6 15.88 x 10 – 6 18.75 x 10 – 6
Pressure/Volume Relations*
Heating Value Calculated gas gravity (air+1.000)
2,620
Specific volume at saturation pressure*, ft3/lbm
Pressure (psig)
Relative volume (L)†
5,000
0.9639
4,500
0.9703
4,000
0.9771
3,500
0.9846
3,000
0.9929
2,900
0.9946
2,800
0.9964
2,700
0.9983
2,620**
1.0000
2,605
1.0022
2.574
2,591
1.0041
2.688
2,516
1.0154
2.673
2,401
1.0350
2.593
2,253
1.0645
2.510
2,090
1.1040
2.422
1,897
1.1633
2.316
1,698
1.2426
2.219
1,477
1.3618
2.118
1,292
1.5012
2.028
1,040
1.7802
1.920
830
2.1623
1.823
640
2.7513
1.727
472
3.7226
1.621
Y function‡
* ** 1
At 220°F. Saturation pressure. Relative volume+V/Vsat in barrels at indicated pressure per barrel at saturation pressure. ‡ Y function+( p *p)/(p sat abs)(V/Vsat*1).
The V rt function at undersaturated conditions may be fit with a secondĆdegree polynomial, resulting in an explicit relation for undersaturated-oil compressibility (see Chap. 3). Total volumes below the bubblepoint can be correlated by the Y function,16,17 defined as Y+
pb * p pb * p + , p(V rt * 1) pƪǒV tńV bǓ * 1ƫ
. . . . . . . . . . . . . . (6.22)
where p and p b are given in absolute pressure units. As Fig. 6.5 shows, Y vs. pressure should plot as a straight line and the linear trend can be used to smooth V rt data at pressures below the bubblepoint. Standing16 and Clark17 discuss other smoothing techniques and corrections that may be necessary when reservoir conditions and laboratory PVT conditions are not the same.
Fig. 6.3—Schematic of a CCE experiment for an oil and a gas condensate. 94
6.4.2 Gas-Condensate Samples. The CCE data for a gas condensate usually include total relative volume, V rt , defined as the volume of gas or of gas-plus-oil mixture divided by the dewpoint volume. Z facPHASE BEHAVIOR
at 290 psia
Fig. 6.4—Volume vs. pressure for an oil during a DLE test (after Standing16).
tors are reported at pressures greater than and equal to the dewpoint pressure. Table 6.10 gives these data for a gas-condensate example. Reciprocal wet-gas FVF, b gw, is reported at dewpoint and initial reservoir pressures, where these values represent the gas equivalent or wet-gas volume at standard conditions produced from 1 bbl of reservoir gas volume. b gw + ǒ5.615
p T p 10 *3Ǔ p sc + 0.198 , sc ZT ZT
. . . . . . . . (6.23)
with b gw in Mscf/bbl, p in psia, and T in °R. Most CCE experiments are conducted in a visual cell for gas condensates, and relative oil (condensate) volumes, V ro, are reported at pressures below the dewpoint. V ro normally is defined as the oil volume divided by the total volume of gas and oil, although some reports define it as the oil volume divided by the dewpoint volume. 6.5 Differential Liberation Expansion The DLE experiment is designed to approximate the depletion process of an oil reservoir18 and thereby provide suitable PVT data to CONVENTIONAL PVT MEASUREMENTS
calculate reservoir performance.16,19-21 Fig. 6.6 illustrates the laboratory procedure of a DLE experiment. Figs. 6.7A through 6.7C and Table 6.11 give DLE data for an oil sample. A blind cell is filled with an oil sample, which is brought to a single phase at reservoir temperature. Pressure is decreased until the fluid reaches its bubblepoint, where the oil volume, V ob , is recorded. Because the initial mass of the sample is known, bubblepoint density, ò ob, can be calculated. The pressure is decreased below the bubblepoint, and the cell is agitated until equilibrium is reached. All gas is removed at constant pressure. Then, the volume, DV g; moles, Dn g; and specific gravity, g g, of the removed gas are measured. The remaining oil volume, V o , is also recorded. This procedure is repeated 10 to 15 times at decreasing pressures and finally at atmospheric pressure. Residual-oil volume, V or , and specific gravity, g or , are measured at 60°F. Other properties are calculated on the basis of measured data ( DV g , V o , Dn g , g g , V or , and g or), including differential solution gas/oil ratio, R sd ; differential oil FVF, B od ; oil density, ò o ; and gas Z factor, Z. For Stage k, these properties can be determined from 95
Bubblepoint Temperature °5F 80 163 185 205
Pressure psia 1,970 2,437 2,520 2,615
Volume cm3 82.30 86.88 87.92 89.05
Fig. 6.5—PVT relation and plot of Y function for an oil sample at pressures below the bubblepoint.
ȍ 379ǒDn Ǔ
calculations, volume factors, R s and B o , are used to relate reservoiroil volumes, V o, to produced surface volumes, V g and V o; i.e.,
k
g j
ǒR sdǓ + k ǒB odǓ k +
j+1
, . . . . . . . . . . . . . . . . . . . . . . . . (6.24)
V or ǒ V oǓ k V or
,
Rs + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.25)
ȍǒ28.97ń5.615ǓǒDn Ǔ ǒg Ǔ
Vg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.28) Vo
and B o +
k
V or(62.4g or) )
g j
ǒò oǓ + k
ǒ V oǓ 350g or )
k
ȍ 0.0764ǒDR k
+
g j
j+1
j+1
5.615ǒB odǓ k
Ǔ ǒg gǓ j
and (Z) k + ǒ1ńRTǓǒ pDV gńDn gǓ k ,
and B od + . . . . . . . . . . . . . . . . . . (6.27)
with V or and V o in bbl, R sd in scf/bbl, B od in bbl/bbl, DV g in ft3, p in psia, Dn g in lbm mol, ò o in lbm/ft3, and T in °R. Note that the subscript j+1 indicates the final DLE stage at atmospheric pressure and reservoir temperature. Reported oil densities are actually calculated by material balance, not measured directly. 6.5.1 Converting From Differential to Stock-Tank Basis. Perhaps the most important step in the application of oil PVT data for reservoir calculations is conversion of the differential solution gas/oil ratio, R sd, and oil FVF, B od , to a stock-tank-oil basis.16,20 For engineering 96
Vg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.30) V or
, . . . . . . . . . . . . . . . . . . (6.26)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.29)
Differential properties R sd and B od reported in the DLE report are relative to residual-oil volume (i.e., the oil volume at the end of the DLE experiment, corrected from reservoir to standard temperature). R sd +
sd j
Vo . Vo
Vo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.31) V or
The equations commonly used to convert differential volume factors to a stock-tank basis are
ǒBB Ǔ
R s + R sb * ǒR sdb * R sdǓ and B o + B od
ǒBB Ǔ , ob
ob
. . . . . . . . . . . . . . . . . . (6.32)
odb
. . . . . . . . . . . . . . . . . . . . . . . . . . . (6.33)
odb
where B ob +bubblepoint-oil FVF, R sb +solution gas/oil ratio from a multistage-separator flash, and R sdb and B odb +differential volume factors at the bubblepoint pressure. The term ( B obńB odb), PHASE BEHAVIOR
TABLE 6.10—CCE DATA FOR GOOD OIL CO. WELL 7 GAS-CONDENSATE SAMPLE Pressure (psig)
Relative volume
Deviation Factor Z
6,000
0.8808
1.144
5,713*
0.8948
1.107**
5,300
0.9158
1.051
5,000
0.9317
1.009
4,800
0.9434
0.981
4,600
0.9559
0.953
4,400
0.9690
0.924
4,300
0.9758
0.909
4,200
0.9832
0.895
4,100
0.9914
0.881
4,000†
1.0000
0.867‡
3,905
1.0089
3,800
1.0194
3,710
1.0299
3,500
1.0559
3,300
1.0878
3,000
1.1496
2,705
1.2430
2,205
1.5246
1,605
2.1035
1,010
3.5665
Pressure/volume relations of reservoir fluid at 186°F. * Reservoir pressure. ** Gas FVF+1.591 Mscf/bbl. † Dewpoint pressure. ‡ Gas FVF+1.424 Mscf/bbl.
representing the volume ratio, V orńV o , is used to eliminate the residual-oil volume, V or , from the Rsd and Bod data. Note that the conversion from differential to “flash” data depends on the separator conditions because B ob and R sb depend on separator conditions. Although, the conversions given by Eqs. 6.32 and 6.33 typically are used, they are only approximate. The preferred method, as originally suggested by Dodson et al.,22 requires that some equilibrium oil be taken at each stage of the DLE experiment and flashed through a multistage separator to give the volume ratios, R s and B o . This laboratory procedure is costly and time-consuming and is seldom used. However, the method is readily incorporated into an equation-ofstate (EOS) -based PVT program. 6.6 Constant Volume Depletion The CVD experiment is designed to provide volumetric and compositional data for gas-condensate and volatile-oil reservoirs producing by pressure depletion. Fig. 6.8 shows the stepwise procedure of a CVD experiment schematically, and Figs. 6.9A through 6.9D and Table 6.12 give CVD data for an example gas-condensate fluid. The CVD experiment provides data that can be used directly by the reservoir engineer, including (1) a reservoir material balance that gives average reservoir pressure vs. recovery of total wellstream (wet-gas recovery), sales gas, condensate, and natural gas liquids; (2) produced-wellstream composition and surface products vs. reservoir pressure; and (3) average oil saturation in the reservoir (liquid dropout and revaporization) that occurs during pressure depletion. For many gas-condensate reservoirs, the recoveries and oil saturation vs. pressure data from the CVD analysis closely approximate actual field performance for reservoirs producing by pressure depletion. When other recovery mechanisms, such as waterdrive and gas cycling, are considered, the basic data required for reservoir engineering are still taken mainly from a CVD report. This section provides a description of the data provided in a standard CONVENTIONAL PVT MEASUREMENTS
Fig. 6.6—Schematic of DLE experiment.
CVD analysis, ways to check the data for consistency,23-25 and how to extract reservoir-engineering quantities from the data.23,26 Initially, the dewpoint, p d , or bubblepoint pressure, p b , of the reservoir sample is established visually and the cell volume, V cell, at saturated conditions is recorded. The pressure is then reduced by 300 to 800 psi and usually by smaller amounts (50 to 250 psi) just below the saturation pressure of more-volatile systems. The cell is agitated until equilibrium is achieved, and volumes V o and V g are measured. At constant pressure, sufficient gas, DV g, is removed to return the cell volume to the original saturated volume. In the laboratory, the removed gas (wellstream) is brought to atmospheric conditions, where the amount of surface gas and condensate are measured. Surface compositions y g and x o of the produced surface volumes from the reservoir gas are measured, as are the volumes DV o and DV g , densities ò o and ò g and oil molecular weight M o . From these quantities, we can calculate the moles of gas removed, Dn g. D ng +
DV o ò o DV g ) . . . . . . . . . . . . . . . . . . . . . . . . . (6.34) Mo 379
These data are reported as cumulative wellstream produced, n p , relative to the initial moles n.
ǒnn Ǔ p
k
+ 1n
ȍ(Dn ) , k
g j
. . . . . . . . . . . . . . . . . . . . . . . . . (6.35)
j+1
where j+1 corresponds to saturation pressure and (Dn g) 1 + 0. The initial amount (in moles) of the saturated fluid is known when the cell is charged. The quantity n pńn is usually reported as cumulative wet gas produced in MMscf/MMscf, which is equivalent to mol/mol. Surface compositions y g and x o of the removed reservoir gas and properties of the removed gas are not reported directly in the laboratory report but are recombined to yield the equilibrium gas (wellstream) composition, y i , which also represents the equilibrium gas remaining in the cell. The C 7) molecular weight of the wellstream, M gC7), is backcalculated from measured specific gravity ( g w + g g ) and reservoir-gas composition, y. C 7) specific gravity of the produced gas, g gC7) , is also reported, but this value is calculated from a correlation. Knowing the cumulative moles removed and its volume occupied as a single-phase gas at the removal pressure, we can calculate the equilibrium gas Z factor from Z+
pDV g . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.36) D n g RT
A “two-phase” Z factor is also reported that is calculated assuming that the gas-condensate reservoir depletes according to the material balance for a dry gas and that the initial condition of the reservoir is at dewpoint pressure. 97
Fig. 6.7A—DLE data for an oil sample from Good Oil Co. Well 4; differential solution gas/oil ratio, Rsd .
ǒ Ǔǒ1 * GG Ǔ,
pd p + Zd Z2
pw
. . . . . . . . . . . . . . . . . . . . . . . . (6.37)
w
where G pw +cumulative wellstream (wet gas) produced and G w +initial wet gas in place. As defined in Eq. 6.37, the term G pwńG w equals n pńn reported in the CVD report. From Eq. 6.37, the only unknown at a given pressure is Z 2 , and the two-phase Z factor is then given by Z2 +
p . . . . . . . . . . . . . . . . . . . . . . (6.38) ǒ p dńZ dǓƪ1 * ǒ n pńn Ǔƫ
Theoretical liquid yields, L i , are also reported for C 3) through C 5) groups in the produced wellstreams at each pressure-depletion stage. These values are calculated with
ǒ Ǔ
M L i + 19.73y i ò i . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.39) i and by summing the yields of components in the particular “plus” group. For example, the liquid yield of C 5) material at CVD Stage k is given by
ǒL Ǔ C 5)
98
C 7) k
+
ȍ ǒL Ǔ
j k
j+i C 5
M + 19.73 ȍ ǒy Ǔ ǒ ò Ǔ . C 7)
j
j k
j+i C 5
j
. . . . . (6.40)
Table 6.13 gives various calculated cumulative recoveries based on the reservoir initially being at its dewpoint. The basis for the calculations is 1 MMscf of dewpoint wet gas in place, G w ; the corresponding initial moles in place at dewpoint pressure is given by G n + vw g +
1 10 6 scf + 2, 638 lbm mol. . . . . . . . . . (6.41) 379 scfńlbm mol
The first row of recoveries (wellstream) simply represents the cumulative moles produced, n pńn, expressed as wet-gas volumes, G pw, in Mscf.
ǒ Ǔ
np G pw + nv g n
+ (2, 638 lbm mol)ǒ379 scfńlbm molǓ
ǒ1 + 1
ǒ Ǔ
np 10 3 MscfńscfǓ n 10 3
ǒnn Ǔ. p
. . . . . . . . . . . . . . . . . . . . . . . . . (6.42)
Recoveries in Rows 2 through 4 (Normal Temperature Separation, Total Plant Products in Primary-Separator Gas, and Total Plant Products in Second-Stage-Separator Gas) refer to production when the reservoir is produced through a three-stage separator. Fig. 6.10 PHASE BEHAVIOR
Fig. 6.7B—DLE data for an oil sample from Good Oil Co. Well 4; differential oil FVF (relative volume), Bod .
illustrates the process schematically. The calculated recoveries are based on multistage-separator calculations that use low-pressure K values and a set of separator conditions chosen arbitrarily or specified when the PVT study is requested. 6.6.1 Recoveries: “Normal Temperature Separation.” Column 1: Initial in Place. In Column 1, Row 2a the stock-tank oil in solution in the initial dewpoint fluid (N+135.7 STB) is calculated by flashing 1 MMscf of the original dewpoint fluid, G w , through a multistage separator. Rows 2b through 2d give the volumes of separator gas at each stage of a three-stage flash of the initial dewpoint fluid: 757.87, 96.68, and 24.23 Mscf, respectively. The mole fraction of wellstream resulting as a surface gas F gg is given by G F gg + d + ǒ757.87 ) 96.68 ) 24.23 Mscfńlbm molǓ Gw
ǒ1
10 3 scfńMscfǓńǒ379 scfńlbm molǓ
+ 0.8788 lbm molńlbm mol,
. . . . . . . . . . . . . . . (6.43)
where G d +total separator “dry” gas and the corresponding mole fraction of stock-tank oil is 0.1212 mol/mol. F gg is used to calculate dry-gas FVF (see Eq. 3.41). For the dewpoint pressure, this gives CONVENTIONAL PVT MEASUREMENTS
B gd + +
ǒ p scńT scǓǒ ZTńp Ǔ B gw + F gg F gg ǒ14.7ń520ǓNJ[0.867(186 ) 460)]ń4015Nj 0.8788
+ 4.487
10 *3 ft 3ńscf. . . . . . . . . . . . . . . . . . . . (6.44)
The producing GOR of the dewpoint mixture for the specified separator conditions can be calculated as R p + G + ƪǒ757.87 ) 96.68 ) 24.23 Mscfńlbm molǓ N
ǒ1
10 3 scfńMscfǓƫń135.7 STBńlbm mol
+ 6, 476 scfńSTB .
. . . . . . . . . . . . . . . . . . . . . . . . (6.45)
The dewpoint solution oil/gas ratio, r sd, is simply the inverse of R p . r sd + r p + 1 Rp + 1.544
10 *4 STBńscf + 154.4 STBńMMscf. . . . . . . . . . . . . . . . (6.46)
Note that specific gravities of stock-tank oil and separator gases are not reported for the separator calculations. 99
Fig. 6.7C—DLE data for an oil sample from Good Oil Co. Well 4; oil viscosity, mo .
Column 2 and Higher. On the basis of 1 MMscf of initial dewpoint fluid, Rows 2a through 2d give cumulative volumes of separator products at each depletion pressure ( N p, G p1, G p2, and G p3 ). The producing GOR of the wellstream produced during a depletion stage is given by
ǒR pǓ + k
ǒG p1 ) G p2 ) G p3Ǔ
k
* ǒG p1 ) G p2 ) G p3Ǔ
ǒN pǓ * ǒN pǓ k k*1
k*1
R p + NJ[(301.57 ) 20.75 ) 5.61) * (124.78 ) 12.09 ) 3.16)]
. . . . . . . . . . . . . . . . . . . . . . . . (6.48)
10 *5 STBńscf
+ 45.8 STBńscf . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.49) 100
* ǒG p1 ) G p2 ) G p3Ǔ
G w ƪǒ n pńn Ǔ k * ǒ n pńn Ǔ k*1ƫ
k*1
.
For p+2,100 psig, this gives F gg + [(301.57 ) 20.75 ) 5.61)*(124.78 ) 12.09 10 3Ǔńǒ1
10 6Ǔ(0.35096 * 0.15438)
+ 0.9558 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.51)
B gd +
ǒ14.7ń520Ǔƪ0.762(186 ) 460)ń2, 115ƫ 0.9558
+ 6.884
rs + rp + 1 Rp 1 + 4.58 21, 580 scfńSTB
k
The dry-gas FVF at 2,100 psig is
10 3ǓNjń(24.0 * 15.4)
In terms of the solution oil/gas ratio,
+
ǒG p1 ) G p2 ) G p3Ǔ
) 3.16)]ǒ1
For 2,100 psig, this gives
+ 21, 850 scfńSTB.
ǒF ggǓ + k
. . . . . . . . . . . . . . . . . . (6.50) .
. . . . . . . . . . . . . . . . . . (6.47)
ǒ1
At a given pressure, the mole fraction of the removed CVD gas wellstream that becomes dry separator gas is given by
10 *3 ft 3ńscf . . . . . . . . . . . . . . . . . . . . (6.52)
In summary, the information provided in the rows labeled Normal Temperature Separation gives estimates of the condensate and sales-gas recoveries assuming a multistage surface separation. For example, at an abandonment pressure of 605 psig, the condensate recovery is 35.1 STB of the 135.7 STB initially in place (in solution in the dewpoint mixture), or 26% condensate recovery. Dry-gas recovery is (685.02)37.79)10.40)+733.21 Mscf of the 878.78 PHASE BEHAVIOR
TABLE 6.11—DLE DATA FOR GOOD OIL CO. WELL 4 OIL SAMPLE
Pressure (psig)
Solution GOR (scf/bbl*)
Relative Oil Volume (RB/bbl*)
2,620 2,350 2,100 1.850 1,600 1,350 1,110 850 600 350 159 0
854 763 684 612 544 479 416 354 292 223 157 0
1.600 1.554 1.515 1.479 1.445 1.412 1.382 1.351 1.320 1.283 1.244 1.075 1.000**
Differential Vaporization Relative Oil Deviation Total Volume Density Factor Z (RB/bbl*) (g/cm3) 1.600 1.665 1.748 1.859 2.016 2.244 2.593 3.169 4.254 6.975 14.693
0.6562 0.6655 0.6731 0.6808 0.6889 0.6969 0.7044 0.7121 0.7198 0.7291 0.7382 0.7892
0.846 0.851 0.859 0.872 0.887 0.903 0.922 0.941 0.965 0.984
Gas FVF (RB/bbl*)
Incremental Gas Gravity
0.00685 0.00771 0.00882 0.01034 0.01245 0.01552 0.02042 0.02931 0.05065 0.10834
0.825 0.818 0.797 0.791 0.794 0.809 0.831 0.881 0.988 1.213 2.039
DLE Viscosity Data at 220°F Pressure (psig)
Oil Viscosity (cp)
5,000 4,500 4,000 3,500 3,000 2,800 2,620 2,350 2,100 1,850 1,600 1,350 1,100 850 600 350 159 0
0.450 0.434 0.418 0.401 0.385 0.379 0.373 0.396 0.417 0.442 0.469 0.502 0.542 0.592 0.654 0.783 0.855 1.286
Calculated Gas Viscosity (cp)
0.0191 0.0180 0.0169 0.0160 0.0151 0.0143 0.0135 0.0126 0.0121 0.0114 0.0093
Gravity of residual oil+35.1°API at 60°F. *Barrels **At
of residual oil.
60°F.
Mscf dry gas originally in place, or 83.4%. These recoveries can be compared with the reported wet-gas (or molar) recovery of 76.787% at 605 psig. In addition to recoveries, the calculated results in this section can be used to calculate solution oil/gas ratio, r s, and dry-gas FVF, B gd , for modified black-oil applications. 6.6.2 Recovery: Plant Products. Rows 3 through 5 consider theoretical liquid recoveries for propane, butanes, and pentanesplus assuming 100% plant efficiency. Recoveries in Rows 3 and 4 are for the calculated separator gases from Stages 1 and 2 of the three-stage surface separation. Recoveries in Row 5 are for the produced wellstreams from the CVD experiment and represent the absolute maximum liquid recoveries that can be expected if the reservoir is produced by pressure depletion. Fig. 6.10 illustrates the recovery calculations schematically. Liquid volumes (in gal/MMscf of initial dewpoint fluid) at CVD Stage k are calculated from
ǒ ǓƪȍǒDnn Ǔ ǒ y Ǔ ƫ,
M (L i) k + 19, 730 ò i i
k
g
i j
j+1
. . . . . . . . . (6.53)
Fig. 6.8—Schematic of CVD experiment.
j
CONVENTIONAL PVT MEASUREMENTS
101
Fig. 6.9A—CVD data for gas-condensate sample from Good Oil Co. Well 7; liquid-dropout curve, Vro .
where j + 1 represents the dewpoint, y i +compositions of wellstream entering the gas plant at various stages of depletion, M i +component molecular weights, and ò i + liquid component densities in lbm/ft3 at standard conditions (Table A-1). Calculated liquid recoveries below the dewpoint use the moles of wellstream produced ( Dn gńn) and the compositions yi from the separator gas (Rows 3 and 4) or wellstream (Row 5) entering the plant. Column 1 (Initial in Place) gives the total recoveries assuming that the entire initial dewpoint fluid is taken to the surface and processed [i.e., k + 1 and (Dn gńn) 1 + 1 in Eq. 6.53]. Note that cumulative recovery of propanes from the first-stage separator during depletion (1,276 gal) is larger than the liquid propane produced in the first-stage-separator gas of the original dewpoint mixture (1,198 gal). This means that the stock-tank oil from the separation of original dewpoint mixture contains more propane than the cumulative stock-tank-oil volumes produced by depletion and three-stage separation. The results given in Rows 3 and 4 cannot be calculated from reported data because surface separator compositions from the threestage separation are not provided in the report. The results in Row 5 can be checked. As an example, consider the C 3 recoveries for the initial-in-place fluid at 2,100 psig.
ǒL Ǔ C3
pd
+ 19, 730 ǒ44.09ń31.66Ǔƪ (1)(0.0837)ƫ + 2, 299 galńMMscf . . . . . . . . . . . . . . . . . . . . (6.54a)
102
ǒ Ǔ
and L C
3 2100
+ 19, 730 ǒ44.09ń31.66Ǔ [0.0825(0.05374) ) 0.0810(0.15438 * 0.05374) ) 0.0757(0.35096 * 0.15438)] + 754 galńMMscf. . . . . . . . . . . . . . . . . (6.54b)
For the C 5) recoveries at the dewpoint,
ǒL Ǔ C 5)
pd
+ 19, 730 [(72.15ń38.96) (0.0091) ) (72.15ń39.36) (0.0152) ) (86.17ń41.43) (0.0179) ) (143ń49.6) (0.0685)] + 5, 513 galńMMscf . . . . . . . . . . . . . . . . . . (6.55)
6.6.3 Correcting Recoveries for Initial Pressure Greater Than Dewpoint Pressure. All recoveries given in Table 6.13 assume that the reservoir pressure is initially at dewpoint. This assumption is made because initial reservoir pressure is not always known with certainty when PVT calculations are made. However, adjusting reported recoveries is straightforward when initial pressure is greater than dewpoint pressure. With Q Table as recoveries given in Columns 2 and higher in Table 6.13, Q d as hydrocarbons in place in Column PHASE BEHAVIOR
Dewpoint Pressure
Fig. 6.9B—CVD data for gas-condensate sample from Good Oil Co. Well 7; equilibrium gas compositions, yi .
1 at dewpoint pressure, and Q as actual cumulative recoveries based on hydrocarbons in place at the initial pressure, Q + Qd
ƪ
ƫ
ǒ pńZǓ ǒ pńZǓ i * ; p y p d , . . . . . . . . . . . . (6.56) ǒ pńZǓ ǒ pńZǓ d
d
Q + Q Table ) DQ d ; p t p d , . . . . . . . . . . . . . . . . . . . (6.57) and DQ d + Q d
pńZ) ƪ((pńZ) * 1ƫ , i
. . . . . . . . . . . . . . . . . . . . (6.58)
d
where DQ d +additional recovery from initial to dewpoint pressure. For the example report, DQ d +
ƪ
ƫ
ǒ5, 728ń1.107Ǔ * 1 Qd ǒ4, 015ń0.867Ǔ
+ 0.1173 Q d ,
. . . . . . . . . . . . . . . . . . . . . . . . . . . (6.59)
recalling that moles of material at dewpoint is 2,638 lbm mol, moles of material at initial pressure of 5,728 psig is n +2, 638(1 ) 0.1173) + 2, 947 lbm mol, and the basis of calculations is G w + 1.173 MMscf of wet gas in place at initial pressure of 5,728 psia. The cumulative wellstream produced at the dewpoint pressure of 4,000 psig is 0.1173(1, 000) + 117.3 Mscf. Recovery at 3,500 psig is 117.3 ) 53.74 + 171.0 Mscf. Likewise, wet-gas recovery CONVENTIONAL PVT MEASUREMENTS
should be increased by 117.3 Mscf for all depletion pressures in the CVD table. For stock-tank-oil recovery, Q d + 135.7 STB, so DQ d + 15.9 STB. Stock-tank-oil recovery at 4,000 psig is 15.9 ) 0 + 15.9 STB; at 3,500 psig the recovery should be 15.9 ) 6.4 + 22.3 STB, and so on. On the basis of 1 MMscf wet gas at the dewpoint or 1.1173 MMscf at initial reservoir pressure, the laboratory hydrocarbon pore volume (HCPV), V pHClab, is the same. V pHClab + ǒG wB gwǓ d + ǒ1
10 6Ǔ
NJǒ Ǔƪ 14.7 520
0.867(186 ) 460) 4, 015
ƫNj
+ 3, 943 ft 3 + ǒG w B gwǓ i + 1.1173
10 6
+ 3, 943 ft 3 .
NJǒ Ǔƪ 14.7 520
1.107(186 ) 460) 5728
ƫNj
. . . . . . . . . . . . . . . . . . . . . . . . . . (6.60)
The actual HCPV of a reservoir is much larger than V pHClab, and the conversion to obtain recoveries for the actual HCPV is simply 103
Fig. 6.9C—CVD data for gas-condensate sample from Good Oil Co. Well 7; equilibrium gas Z factor, Zg .
Q actual + Q lab
V pHCactual , V pHClab
. . . . . . . . . . . . . . . . . . . . . . . (6.61)
where Q lab +laboratory value given by Eqs. 6.55 and 6.57. As an example, suppose geological data indicate a HCPV of 625,000 bbl (82.45 acre-ft), or 3.509 106 ft3. Then, original wet gas in place is G w + 1.1173
6 10 6 3.509 10 3, 943
+ 994.3 MMscf . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.62) and condensate in solution at initial pressure is given by 6 N + 135.7(1.1173) 3.509 10 3, 943
+ 134, 900 STB .
. . . . . . . . . . . . . . . . . . . . . . . . . . (6.63)
6.6.4 Liquid-Dropout Curve. Table 6.11 and Figs. 6.9A through 6.9D show relative oil volumes, V ro, measured in the example CVD experiment. V ro is defined as the volume of oil, V o , at a given pressure divided by the original saturation volume, V s. This relative volume is an excellent measure of the average reservoir-oil saturation (normalized) that will develop during depletion of a gas-condensate 104
reservoir. Correcting for water saturation, S w , the reservoir-oil saturation can be calculated from V ro with S o + (1 * S w)V ro .
. . . . . . . . . . . . . . . . . . . . . . . . . . . (6.64)
For most gas condensates, V ro shows a maximum near 2,000 to 2,500 psia. Cho et al.27 give a correlation for maximum liquid dropout as a function of temperature and C 7) mole percent in the dewpoint mixture. ǒ V roǓ
max
+ 93.404 ) 4.799 z C
7)
* 19.73 ln T , . . . . . . (6.65)
with z C7) in mole percent and T in °F. The correlation predicts (V ro) max +23.2% for the example condensate fluid compared with 24% measured experimentally (at 2,100 psig). Fig. 6.11 shows values of (V ro) max vs. T and z C7)from Eq. 6.65. Considerable attention usually is given to matching the liquiddropout curve when an EOS is used. Some gas condensates havewhat is referred to as a “tail,” where liquid drops out very slowly (sometimes for several thousand psi below the dewpoint) before finally increasing toward a maximum. Matching this behavior with an EOS can prove difficult, and the question is whether matching the tail is really necessary (see Appendix C). What really matters for reservoir calculations of a gas-condensate fluid is how much original stock-tank condensate is “lost” because of retrograde condensation in the reservoir. The shape and magniPHASE BEHAVIOR
Fig. 6.9D—CVD data for gas-condensate sample from Good Oil Co. Well 7; wet-gas material balance.
tude of liquid dropout reflects the change in producing oil/gas ratio, r p [ r s . A tail on a liquid-dropout curve implies that the producing wellstream is becoming only slightly leaner (i.e., r s is decreasing only slightly). The cumulative condensate recovery is given by Gp
Np +
ŕ r dG , s
p
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.66)
0
where G p +cumulative dry gas produced. Cumulative condensate production is readily evaluated from a plot of r s vs. G p . One of the most important checks of an EOS characterization for any gas condensate, particularly one with a tail, is N p calculated from CVD data vs. N p calculated from the EOS characterization. It is alarming how much the surface condensate recovery can be underestimated if the tail is not matched properly. We do not recommend matching the dewpoint exactly with a liquid-dropout curve that is severely overpredicted in the region where measured results indicate little dropout. If the EOS characterization cannot be modified to honor the tail of liquid-dropout curve, it is preferable to underpredict the measured dewpoint pressure and match only the higher liquid-dropout volumes. In summary, oil relative volume, V ro, is not important per se; however, the effect of liquid dropout on surface condensate production CONVENTIONAL PVT MEASUREMENTS
should be emphasized. In fact, the effect of shape and magnitude of liquid dropout on fluid flow in the reservoir is negligible, and any EOS match will probably have the same effect on fluid flow from the reservoir into the wellbore (i.e., inflow performance). 6.6.5 Consistency Check of CVD Data. Reudelhuber and Hinds24 give a detailed procedure for checking CVD data consistency that involves a material-balance check on components and phases and yields oil compositions, density, molecular weight, and M C7). Together with reported data, these calculated properties allow K values to be calculated and checked for consistency with the Hoffman et al.10 method.11,28 Whitson and Torp’s23 material-balance equations are summarized later. Similar equations can also be derived for a DLE experiment when equilibrium gas compositions and oil relative volumes are reported. Reported CVD data include temperature, T ; dewpoint pressure, p d , or bubblepoint pressure, p b ; dewpoint Z factor, Z d, or bubblepoint-oil density, ò ob . Additional data at each Depletion Stage k include oil relative volume, V ro; initial fraction of cumulative moles produced, n pńn; gas Z factor (not the twophase Z factor), Z; equilibrium gas composition, yi ; and equilibrium gas (wellstream) C 7) molecular weight, M g C7). The equilibrium gas density, ò g ; molecular weight, M g ; and wellstream gravity, g w + M gńM air , are readily calculated at each 105
TABLE 6.12—CVD DATA FOR GOOD OIL CO. WELL 7 GAS-CONDENSATE SAMPLE 2* Reservoir Pressure, psig 5,713**
4,000†
CO2
0.18
0.18
0.18
0.18
0.18
0.19
N2
0.13
0.13
0.13
0.14
0.15
0.15
0.14
C1
61.72
61.72
63.10
65.21
69.79
70.77
66.59
C2
14.10
14.10
14.27
14.10
14.12
14.63
16.06
C3
8.37
8.37
8.26
8.10
7.57
7.73
9.11
i-C4
0.98
0.98
0.91
0.95
0.81
0.79
1.01
n-C4
3.45
3.45
3.40
3.16
2.71
2.59
3.31
i-C5
0.91
0.91
0.86
0.84
0.67
0.55
0.68
n-C5
1.52
1.52
1.40
1.39
0.97
0.81
1.02
C7
1.79
1.79
1.60
1.52
1.03
0.73
0.80
C7+
6.85
6.85
5.90
4.41
2.00
1.06
1.07
100.00
100.00
100.00
100.00
100.00
100.00
100.00
Component, mol%
Total
3,500
2,900
2,100
1,300
605
0‡
0.21
Properties C7+ molecular weight
143
143
138
128
116
111
110
C7+ specific gravity
0.795
0.795
0.790
0.780
0.767
0.762
0.761
Equilibrium gas deviation factor, Z
1.107
0.867
0.799
0.748
0.762
0.819
0.902
Two-phase deviation factor, Z
1.107
0.867
0.802
0.744
0.704
0.671
0.576
0.000
5.374
15.438
35.096
57.695
76.787
Wellstream produced, cumulative % of initial
93.515
From smooth compositions C3+, gal/Mscf
9.218
9.218
8.476
7.174
5.171
4.490
5.307
C4+, gal/Mscf
6.922
6.922
6.224
4.980
3.095
2.370
2.808
C5+, gal/Mscf
5.519
5.519
4.876
3.692
1.978
1.294
1.437
23.9
22.5
18.1
Retrograde Condensation During Gas Depletion Retrograde liquid volume,
0.0
3.3
19.4
12.6
% hydrocarbon pore space *Study conducted at 186°F. ** Original reservoir pressure. † Dewpoint pressure. ‡ 0-psig residual-liquid properties: 47.5°API oil gravity at 60°; 0.7897 specific gravity at 60/60°F; and molecular weight of 140.
Depletion Stage k [and at the dewpoint ( k + 1) for a gas-condensate sample] from
ǒM gǓ + k
ȍ(y ) N
i k
Mi ,
. . . . . . . . . . . . . . . . . . . . . . . . . . (6.67)
i+1
ǒò gǓ + k
ǒ Ǔ
np (n t) k + 1 * n , k
p ǒM gǓ k (Z) k RT
, . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.68)
and ǒg gǓ k + ǒ g wǓ k +
ǒM gǓ
k
28.97
.
. . . . . . . . . . . . . . . . . . . . (6.69)
On a basis of 1 mol initial dewpoint fluid ( n + 1), the cell volume is
ǒn gǓ + k
ǒ p Ǔ ǒV gǓ k k
(Z) k RT
,
and (n o) k + (n t) k * ǒn gǓ k , . . . . . . . . . . . . . . . . . . . . . . . . (6.73) and moles and mass of the individual phases remaining in the cell at Stage k are given by
ȍǒDnn Ǔ ǒM Ǔ , k
(m t) k + M s *
g
g j
j +2
Z RT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.70) V cell + dp d for a gas condensate and M V cell + ò ob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (6.71) ob for a volatile oil. Oil and gas volumes, respectively, at Stage k are (V o) k+ V cell (V ro) k and ǒV gǓ k + V cellƪ1 * (V ro) kƫ . . . . . . . . . . . . . . . . . . . . . (6.72) Moles and mass of the total material remaining in the cell at Stage k are given by 106
j
ǒm gǓ + ǒn gǓ ǒM gǓ , k k k and (m o) k + (m t) k * ǒm gǓ k .
. . . . . . . . . . . . . . . . . . . . . . (6.74)
In Eqs. 6.73 and 6.74,
ǒDnn Ǔ + ǒnn Ǔ * ǒnn Ǔ g
p
j
p
j
, . . . . . . . . . . . . . . . . . . . . (6.75)
j*1
M s +saturated-fluid molecular weight, and (