OPTICAL SYSTEM DESIGN
This page intentionally left blank
Optical System Design Robert E. Fischer President, OPTICS 1, Incorporated
Biljana Tadic-Galeb Senior Staff Optical Engineer, OPTICS 1, Incorporated
With contributions by Rick Plympton Bob Weiderhold Chanda Bartlett Walker Ranko Galeb Michael Newell McGraw-Hill New York • San Francisco • Washington, D.C. • Auckland • Bogotá Caracas • Lisbon • London • Madrid • Mexico City • Milan Montreal • New Delhi • San Juan • Singapore Sydney • Tokyo • Toronto
Copyright © 2000 by The McGraw-Hill Companies, Inc. All rights reserved. Manufactured in the United States of America. Except as permitted under the United States Copyright Act of 1976, no part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of the publisher. 0-07-150025-1 The material in this eBook also appears in the print version of this title: 0-07-134916-2. All trademarks are trademarks of their respective owners. Rather than put a trademark symbol after every occurrence of a trademarked name, we use names in an editorial fashion only, and to the benefit of the trademark owner, with no intention of infringement of the trademark. Where such designations appear in this book, they have been printed with initial caps. McGraw-Hill eBooks are available at special quantity discounts to use as premiums and sales promotions, or for use in corporate training programs. For more information, please contact George Hoare, Special Sales, at
[email protected] or (212) 9044069. TERMS OF USE This is a copyrighted work and The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and its licensors reserve all rights in and to the work. Use of this work is subject to these terms. Except as permitted under the Copyright Act of 1976 and the right to store and retrieve one copy of the work, you may not decompile, disassemble, reverse engineer, reproduce, modify, create derivative works based upon, transmit, distribute, disseminate, sell, publish or sublicense the work or any part of it without McGraw-Hill’s prior consent. You may use the work for your own noncommercial and personal use; any other use of the work is strictly prohibited. Your right to use the work may be terminated if you fail to comply with these terms. THE WORK IS PROVIDED “AS IS.” McGRAW-HILL AND ITS LICENSORS MAKE NO GUARANTEES OR WARRANTIES AS TO THE ACCURACY, ADEQUACY OR COMPLETENESS OF OR RESULTS TO BE OBTAINED FROM USING THE WORK, INCLUDING ANY INFORMATION THAT CAN BE ACCESSED THROUGH THE WORK VIA HYPERLINK OR OTHERWISE, AND EXPRESSLY DISCLAIM ANY WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. McGraw-Hill and its licensors do not warrant or guarantee that the functions contained in the work will meet your requirements or that its operation will be uninterrupted or error free. Neither McGraw-Hill nor its licensors shall be liable to you or anyone else for any inaccuracy, error or omission, regardless of cause, in the work or for any damages resulting therefrom. McGraw-Hill has no responsibility for the content of any information accessed through the work. Under no circumstances shall McGraw-Hill and/or its licensors be liable for any indirect, incidental, special, punitive, consequential or similar damages that result from the use of or inability to use the work, even if any of them has been advised of the possibility of such damages. This limitation of liability shall apply to any claim or cause whatsoever whether such claim or cause arises in contract, tort or otherwise. DOI: 10.1036/0071349162
Professional
Want to learn more? We hope you enjoy this McGraw-Hill eBook! If you’d like more information about this book, its author, or related books and websites, please click here.
We dedicate this book to our families who have tolerated many lonely evenings and weekends as we were writing, computing, and otherwise getting our material together. We also would like to acknowledge the many colleagues with whom we have both worked with over the years who have helped to make our field of optical design so fascinating, challenging, and rewarding. We also appreciate the efforts of our colleagues at OPTICS 1, especially Michael Newell and Mike Couture, who helped review the manuscript. Also thanks to our dear friend and colleague Max Reidl for his valuable support. Also, the support, encouragement, and friendship of our colleague Warren Smith whose books are classics in their own right. We also want to pay a special thanks to our professors from whom we learned optical design and engineering: R. E. Hopkins, R. Kingslake, W. L. Hyde, H. H. Hopkins, and J. McDonald.
v
This page intentionally left blank
For more information about this title, click here
CONTENTS
Preface
Chapter 1.
Chapter 2.
Chapter 3.
Chapter 4.
Chapter 5.
Basic Optics and Optical System Specifications
xiii
1
The Purpose of an Imaging Optical System How to Specify Your Optical System: Basic Parameters Basic Definition of Terms Useful First-Order Relationships
2 3 10 13
Stops, Pupils, and Other Basic Principles
27
The Role of the Aperture Stop Entrance and Exit Pupils Vignetting
28 28 30
Diffraction, Aberrations, and Image Quality
35
What Image Quality Is All About What Are Geometrical Aberrations and Where Do They Come From? What Is Diffraction? Diffraction-Limited Performance Derivation of System Specifications
36 37 41 43 45
The Concept of Optical Path Difference
49
Optical Path Difference (OPD) and the Rayleigh Criteris? Peak-to-Valley and RMS Wavefront Error The Wave Aberration Polynomial Depth of Focus
50 52 55 56
Review of Specific Geometrical Aberrations and How to Get Rid of Them
61
Spherical Aberration Coma Astigmatism
63 72 76
vii
viii
Contents
Chapter 6.
Chapter 7.
Chapter 8.
Chapter 9.
Chapter 10.
Field Curvature and the Role of Field Lenses Distortion Axial Color Lateral Color Parametric Analysis of Aberrations Introduced by Plane Parallel Plates
78 85 88 90
Glass Selection (Including Plastics)
95
Material Properties Overview The Glass Map and Partial Dispersion Parametric Examples of Glass Selection How to Select Glass Plastic Optical Materials
96 97 103 107 110
Spherical and Aspheric Surfaces
115
Definition of an Aspheric Surface Conic Surfaces Application of Aspheric Surfaces in Reflective and Refractive Systems Guidelines in the Use of Aspheric Surfaces Specifications of Aspheric Surfaces
116 118
Design Forms
129
Introduction System Configurations for Refractive Systems System Configurations for Reflective Systems Reflective Systems, Relative Merits Refractive Systems, Relative Merits Mirrors and Prisms Design of Visual Systems
130 131 139 144 147 147 155
The Optical Design Process
167
What Do We Do When We Optimize a Lens System? How Does the Designer Approach the Optical Design Task? Sample Lens Design Problem
169 172 176
Computer Performance Evaluation
181
What Is Meant by Performance Evaluation What Is Resolution?
182 182
90
119 124 127
ix
Contents
Chapter 11.
Chapter 12.
Chapter 13.
Ray Trace Curves Spot Diagrams Optical Path Difference Encircled Energy MTF
184 190 191 192 193
Gaussian Beam Imagery
203
Beam Waist and Beam Divergence Collimation of Laser Beams Propagation of Gaussian Beams and Focusing into a Small Spot Truncation of Gaussian Beams Application of Gaussian Beam Optics in Laser Systems F - Lenses in Laser Scanners
205 207 208 209 212 215
Basics of Thermal Infrared Imaging in the 3- to 5- and 8- to 12-m Spectral Bands (Plus UV Optics)
217
The Basics of Thermal Infrared Imaging The Dewar, Cold Stop, and Cold Shield Cold Stop Efficiency Scanning Methods IR Materials Reduced Aberrations with IR Materials Image Anomalies Athermalization System Design Examples Optical Systems for the UV
218 221 223 226 233 240 244 250 254 259
Diffractive Optics
263
Diffraction Grating, Volume Holographic Elements, Kinoforms, and Binary Surfaces Diffraction Efficiency Achromatic Doublet and the Hybrid RefractiveDiffractive Achromat Applications of Diffractive Optical Components Parametric Examples of Diffractive Optics Designs Summary of Diffractive Optics
Chapter 14.
264 272 275 279 281 287
Design of Illumination Systems
289
Introduction Köhler and Abbe Illumination
290 291
x
Contents
Chapter 15.
Chapter 16.
Chapter 17.
Chapter 18.
Optical Invariant and Etendue Other Types of Illumination Systems
292 296
Performance Evaluation and Optical Testing
301
Testing with the Standard 1951 U.S. Air Force Target The Modulation Transfer Function Interferometry Other Tests
302 306 308 313
Tolerancing and Producibility
315
Introduction What Are Testplates and Why Are They Important? How to Tolerance an Optical System How Image Degradations from Different Tolerances Are Summed Forms of Tolerances Adjusting Parameters Typical Tolerances for Various Cost Models Example of Tolerance Analysis Surface Irregularities How Does Correlation Relate to Performance? Effect to Spot Diameter Effect to MTF: The Optical Quality Factor Beam Diameter and Surface Irregularity The Final Results
316 317 322
Optical Manufacturing Considerations
357
Material Manufacturing Special Fabrication Considerations Relative Manufacturing Cost Sourcing Considerations Conclusion
358 364 370 380 380 383
Polarization Issues In Optical Design
387
Introduction What Is Polarized Light? Polarization Elements Mathematics of Polarized Light
388 388 392 404
325 328 332 334 336 342 345 346 347 350 352
xi
Contents
Chapter 19.
Chapter 20.
Chapter 21.
Chapter 22.
Polarization Aberrations and Polarization Ray Tracing Geometrical Issues and the Maltese Cross Stress Birefringence Polarized Systems and Design Techniques
407 409 412 413
Optical Thin Films
421
Introduction Designing Optical Coatings Various Categories of Optical Coatings Optical Coating Process Coating Performance Versus Number of Layers Specifying Coating Requirements Relationship Between Production Cost, Tolerances, and Quality
422 423 424 430 435 436 437
Hardware Design Issues
439
Off-the-Shelf Optics How to Effectively Work with Off-the-Shelf Optics Working with Off-the-Shelf Singlets and Doublets Example of Lens Used at Conjugates Different from What It Was Designed Pupil Matching Development of a Lab Mockup Using Off-the-Shelf Optics Stray Light Control Optomechanical Design
440 442 443 444 445 448 448 453
Lens Design Optimization Case Studies
457
Error Function Construction Achromatic Doublet Lens Design Double Gauss Lens Design Digital Camera Lens Binocular Design Parametric Design Study of Simple Lenses Using Advanced Manufacturing Methods Design Data for Double Gauss
458 459 465 486 494
Bloopers and Blunders in Optics
513
Distortion in a 1:1 Imaging Lens Zoom Periscope Sign of Distortion
514 516 516
499 502
xii
Contents
Chapter 23.
Lens Elements That Are Not Necessary Pupil Problems Not Enough Light Athermalization Using Teflon Athermalization Specifications Bad Glass Choice Elements in Backwards Insufficient Sampling of Fields of View of Aperture Images Upside Down or Rotated The Hubble Telescope Null Lens Problem
518 519 520 521 521 521 522 523 524 525
Rules of Thumb and Hints
531
Glossary Bibliography
537 547
Index
551
PREFACE
The design of imaging optical systems is an engineering discipline which has been practiced and written about for many years. In many ways, optical design is both a science and an art, and for this reason it is a technology that can cause problems if it is not done properly. Furthermore, most books on the subject tend to be complex and difficult to follow and to understand. With this book, we hope to bring the understanding of our discipline to everyone. We are all aware of cameras, binoculars, and other optical systems and instruments. With the advent of the new millennium, the field of optics and photonics will see a tremendous surge in applications. This will be fueled by a closer association with electronics in devices such as digital cameras, enhanced machine vision systems, MEMS, and microoptical systems for telecommunications and other related applications, many of which have yet to be invented. With this surge in the applications of optics, the educational process of training experienced optical designers and engineers becomes extremely important if not critical. We realize that it is difficult to be an expert in everything. We also realize that optical manufacturing, polarization, and optical coatings are extremely important subjects that need to be covered in this book. We are honored to have guest chapters written by experts in their fields: Rick Plympton and Bob Weiderhold on optical manufacturing (Chapter 17), Chanda Barlett Walker on polarization in optical systems (Chapter 18), and Ranko Galeb on thin films and optical coatings (Chapter 19). We also appreciate all of the hard work by our colleague Michael Newell who read the manuscript in great depth and gave us many constructive suggestions. Also Max Riedl, Mike Couture, Jim Contreras, Dave Kappel, and Steve McClain all helped in the review. Our goal in writing this book is to teach optical design and engineering in a fully unintimidating way, using clear and easy-to-understand graphics and explanations. Many authors feel an obligation to include complex mathematical derivations. We have taken a very different approach. We will make this book clear and easy to understand, with the goal that you will learn the subject matter with a combination of complete graphics, easy-to-follow explanations, and just enough math to
xiii Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
xiv
Preface be useful, but not too much math to make the book hard to follow or difficult to understand. Optical System Design is largely based on the firm foundation of the short course by the same title taught by Bob Fischer to hundreds of students over the past 15 years. The course has been honed, polished, and expanded over the years. It is available on CD-ROM and videotape, and finally, via this book. Typical comments have been: This course was just what I had hoped it would be. It condensed the vast optical world into the key elements necessary for a broad understanding of the subject and an excellent foundation for future study. Good Job! Excellent presentation! This is an invaluable course for those who are engaged in optical systems efforts and have a minimum training in optics. A fast paced, well-prepared study, presented by a hands-on-instructor. I learned what I came to learn, thanks. Excellent! Wonderful presentation and technique. Material was well covered. Excellent in explaining and answering questions. Very useful rules of thumb, great presentation. Thanks! Very professional and excellent presentation.
This book is for everyone from program managers to seasoned optical designers and engineers, mechanical engineers, electrical engineers, and others. You will find that it is like reading Gulliver’s Travels. We all read Gulliver’s Travels in elementary school, some of us again in high school, and some scholars wrote their PhD theses on the book. Gulliver’s Travels can be read at multiple levels, just like this book. ROBERT E. FISCHER BILJANA TADIC-GALEB
OPTICAL SYSTEM DESIGN
This page intentionally left blank
CHAPTER
1
Basic Optics and Optical System Specifications
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
2
Chapter 1 This chapter will discuss what a lens or mirror system does and how we specify an optical system. You will find that properly and completely specifying a lens system early in the design cycle is an imperative ingredient required to design a good system.
The Purpose of an Imaging Optical System The purpose of virtually all image-forming optical systems is to resolve a specified minimum-sized object over a desired field of view. The field of view is expressed as the spatial or angular extent in object space, and the minimum-sized object is the smallest resolution element which is required to identify or otherwise understand the image. The word “spatial” as used here simply refers to the linear extent of the field of view in the plane of the object. The field of view can be expressed as an angle or alternatively as a lateral size at a specified distance. For example, the field of view might be expressed as 10 10°, or alternatively as 350 350 m at a distance of 2 km, both of which mean the same thing. A good example of a resolution element is the dot pattern in a dot matrix printer. The capital letter E has three horizontal bars, and hence five vertical resolution elements are required to resolve the letter. Horizontally, we would require three resolution elements. Thus, the minimum number of resolution elements required to resolve capital letters is in the vicinity of five vertical by three horizontal. Figure 1.1 is an example of this. Note that the capital letter B and the number 8 cannot be distinguished in a 3 5 matrix, and the 5 7 matrix of dots will do just fine. This applies to telescopes, microscopes, infrared systems, camera lenses, and any other form of image-forming optics. The generally accepted guideline is that approximately three resolution elements or 1.5 line pairs over the object’s spatial extent are required to acquire an object. Approximately eight resolution elements or four line pairs are required to recognize the object and 14 resolution elements or seven line pairs are required to identify the object. There is an important rule of thumb, which says that this smallest desired resolution element should be matched in size to the minimum detector element or pixel in a pixelated charged-coupled device (CCD) or complementary metal-oxide semiconductor (CMOS)–type sensor. While
Basic Optics and Optical System Specifications
3
Figure 1.1 Illustration of Number of Resolution Elements Required to Resolve or Distinguish Alphanumerics
not rigorous, this is an excellent guideline to follow for an optimum match between the optics and the sensor. This will become especially clear when we learn about the Nyquist Frequency in Chap. 21, where we show a digital camera design example. In addition, the aperture of the system and transmittance of the optics must be sufficient for the desired sensitivity of the sensor or detector. The detector can be the human eye, a CCD chip, or film in your 35-mm camera. If we do not have enough photons to record the imagery, then what good is the imagery? The preceding parameters relate to the optical system performance. In addition, the design form or configuration of the optical system must be capable of meeting this required level of performance. For example, most of us will agree that we simply cannot use a single magnifying glass element to perform optical microlithography where submicron line-width imagery is required, or even lenses designed for 35-mm photography for that matter. The form or configuration of the system includes the number of lens or mirror elements along with their relative position and shape within the system. We discuss design configurations in Chap. 8 in detail. Furthermore, we often encounter special requirements, such as cold stop efficiency, in infrared systems, scanning systems, and others. These will be addressed later in this book. Finally, the system design must be producible, meet defined packaging and environmental requirements, weight and cost guidelines, and satisfy other system specifications.
How to Specify Your Optical System: Basic Parameters Consider the lens shown in Fig. 1.2 where light from infinity enters the lens over its clear aperture diameter. If we follow the solid ray, we see that
4
Chapter 1
Figure 1.2 Typical Specifications
it is redirected by each of the lens element groups and components until it comes to focus at the image. If we now extend this ray backwards from the image towards the front of the system as if it were not bent or refracted by the lens groups, it intersects the entering ray at a distance from the image called the focal length. The final imaging cone reaching the image at its center is defined by its ƒ/number or ƒ/#, where focal length ƒ/number clear aperture diameter You may come across two other similar terms, effective focal length and equivalent focal length, both of which are often abbreviated EFL. The effective focal length is simply the focal length of a lens or a group of lenses. Equivalent focal length is very much the same; it is the overall focal length of a group of lens elements, some or all of which may be separated from one another. The lens is used over a full field of view, which is expressed as an angle, or alternatively as a linear distance on the object plane. It is important to express the total or full field of view rather than a subset
Basic Optics and Optical System Specifications
5
of the field of view. This is an extremely critical point to remember. For example, assume we have a CCD camera lens covering a sensor with a 3 4 5 aspect ratio. We could specify the horizontal field of view, which is often done in video technology and cinematography. However, if we do this, we would be ignoring the full diagonal of the field of view. If you do specify a field of view less than the full or total field, you absolutely must indicate this. For example, it is quite appropriate to specify the field of view as ±10°. This means, of course, that the total or full diagonal field of view is 20°. Above all, do not simply say “field of view 10°” as the designer will be forced to guess what you really mean! System specifications should include a defined spectral range or wavelength band over which the system will be used. A visible system, for example, generally covers the spectral range from approximately 450 nm to 650 nm. It is important to specify from three to five specific wavelengths and their corresponding relative weights or importance factors for each wavelength. If your sensor has little sensitivity, say, in the blue, then the image quality or performance of the optics can be more degraded in the blue without perceptible performance degradation. In effect, the spectral weights represent an importance factor across the wavelength band where the sensor is responsive. If we have a net spectral sensitivity curve, as in Fig. 1.3, we first select five representative wavelengths distributed over the band, 1 450 nm through 5 650 nm, as shown. The circular data points represent the relative sensitivity at the specific wavelengths, and the relative weights are now the normalized area or integral within each band from band 1 through band 5, respectively. Note that the weights are not the ordinate of the curve at each wavelength as you might first expect but rather the integral within each band. Table 1.1 shows the data for this example. Even if your spectral band is narrow, you must work with its bandwidth and derive the relative weightings. You may find some cases where you think the spectral characteristics suggest a monochromatic situation but in reality, there is a finite bandwidth. Pressure-broadened spectral lines emitted by high-pressure arc lamps exhibit this characteristic. Designing such a system monochromatically could produce a disastrous result. In most cases, laser-based systems only need to be designed at the specific laser wavelength. System packaging constraints are important to set at the outset of a design effort, if at all possible. These include length, diameter, weight, distance or clearance from the last surface to the image, location and space
6
Chapter 1
Figure 1.3 Example of Spectral Sensitivity Curve
TABLE 1.1 Example of Spectral Sensitiv ity and Relative Wavelength Weights
Wavelength, nm
Relative sensitivity
Relative weight
450
0.05
0.08
500
0.2
0.33
550
1.0
1.0
600
0.53
0.55
650
0.09
0.16
for fold mirrors, filters, and/or other components critical to the system operation. Sets of specifications often neglected until it is too late are the environmental parameters such as thermal soak conditions (temperature range) that the system will encounter. Also, we may have radial thermal gradients, which are changes in temperature from the optical axis outward; diame-
Basic Optics and Optical System Specifications
7
tral thermal gradients, which are thermal gradients across the diameter of the system in a nonaxially symmetrical profile; and axial gradients, which are thermal gradients from the front to the rear of the system. You may also be provided with a set of operational specifications and a set of storage specifications with respect to temperature. System transmittance, or throughput, as well as relative illumination, or brightness, uniformity over the image format are also often specified. One of the most important specifications is the optical performance or image quality. The following list contains some of the more common ways of specifying the image quality, along with simple definitions. Each of these will be discussed in more detail in Chap. 10. Modulation transfer function (MTF ). The modulation (think of the word contrast) versus the number of line pairs per millimeter in the image RMS blur diameter. The diameter of a circle containing approximately 68 percent of the energy imaged from a point source Encircled energy (or ensquared energy). The diameter of a circle (or side of a square such as a pixel) containing a given percent of energy, for example, 80 percent Root-mean-square (rms) wavefront error. The rms departure of the real wavefront from a perfect wavefront Other. Depending on the functional requirements of the system, there may be other performance requirements relating to image quality, for example, point spread function (PSF), control of specific aberrations, etc. The most fundamental set of first-order specifications are focal length, clear aperture diameter (more properly called entrance pupil diameter, as will be explained in Chap. 2), and ƒ/number. As we know, the ƒ/number is the focal length divided by the clear aperture diameter (the entrance pupil diameter). There is, however, another important and related quantity called the numerical aperture (NA), which is often used. The numerical aperture is simply the sine of the half cone angle of the limiting edge ray coming to the axial image, or the sine of the half cone angle coming from the axial object point, as shown in Fig. 1.4. Why would we want or need yet another term to remember? The reason is that the definition of focal length is based on light from infinity entering the system. What if we have a so-called finite conjugate system where neither the
8
Chapter 1
Figure 1.4 Numerical Aperture and ƒ/#
object nor the image is at infinity? The traditional definition of focal length and ƒ/# would be misleading since the system really is not being used with collimated light input. Numerical aperture is the answer. The numerical aperture is simply the sine of the image cone half angle, regardless of where the object is located. We can also talk about the numerical aperture at the object, which is the sine of the half cone angle from the optical axis to the limiting marginal ray emanating from the center of the object. Microscope objectives are routinely specified in terms of numerical aperture. Some microscope objectives reimage the object at a finite distance, and some have collimated light exiting the objective. These latter objectives are called infinity corrected objectives, and they require a “tube lens” to focus the image into the focal plane of the eyepiece or alternatively onto the CCD or other sensor. As noted earlier, the definition of focal length implies light from infinity. And similarly, ƒ/number is focal length divided by the clear aperture diameter. Thus, ƒ/number is also based on light from infinity. Two terms commonly encountered in finite conjugate systems are “ƒ/number at used conjugate” and “working ƒ/number.” These terms define the equivalent ƒ/number, even though the object is not at infini-
Basic Optics and Optical System Specifications
9
ty. The ƒ/number at used conjugate is 1/(2NA), and this is valid whether the object is at infinity or at a finite distance. It is important at the outset of a design project to compile a specification for the desired system and its performance. The following is a candidate list of specifications:
Optical system basic operational and performance specifications and requirements
Basic system parameters: Object distance Image distance Object to image total track Focal length ƒ/number (or numerical aperture) Entrance pupil diameter Wavelength band Wavelengths and weights for 3 or 5 s Full field of view Magnification (if finite conjugate) Zoom ratio (if zoom system) Image surface size and shape Detector type Optical performance: Transmission Relative illumination (vignetting) Encircled energy MTF as a function of line pairs/mm Distortion Field curvature Lens system: Number of elements Glass versus plastic Aspheric surfaces Diffractive surfaces Coatings Sensor: Sensor type Full diagonal Number of pixels (horizontal) Number of pixels (vertical) Pixel pitch (horizontal) Pixel pitch (vertical) Nyquist frequency at sensor, line pairs/mm Packaging: Object to image total track Entrance and exit pupil location and size Back focal distance Maximum diameter
10 Optical system basic operational and performance specifications and requirements (Continued)
Chapter 1
Maximum length Weight Environmental: Thermal soak range to perform over Thermal soak range to survive over Vibration Shock Other (condensation, humidity, sealing, etc.) Illumination: Source type Power, in watts Radiometry issues, source: Relative illumination Illumination method Veiling glare and ghost images Radiometry issues, imaging: Transmission Relative illumination Stray light attenuation Schedule and cost: Number of systems required Initial delivery date Target cost goal
Basic Definition of Terms There is a term called first-order optics. In first-order optics the bending or refraction of a lens or lens group happens at a specific plane rather than at each lens surface. In first-order optics, there are no aberrations of any kind and the imagery is perfect, by definition. Let us first look at the simple case of a perfect thin positive lens often called a paraxial lens. The limiting aperture that blocks the rays beyond the lens clear aperture is called the aperture stop. The rays coming from an infinitely distant object that passes through the lens clear aperture focus in the image plane. A paraxial positive lens is shown in Fig. 1.5. The rays coming from an infinitely distant point on the optical axis approach the lens as the bundle parallel to the optical axis. The ray that goes along the optical axis passes through the lens without bending. However, as we move away from the axis, rays are bent more and more as we approach the edge of the clear aperture. The ray that goes through the edge of the aperture parallel to the optical axis is called the marginal ray. All of the rays parallel to the optical axis focus at a point on the
Basic Optics and Optical System Specifications
11
optical axis in the focal plane. The rays that are coming from a nonaxial object point form an angle with the optical axis. One of these rays is called a chief ray, and it goes through the center of the lens (center of the aperture stop) without bending. A common first-order representation of an optical system is shown in Fig. 1.6. What we have here is the representation of any optical system, yes, any optical system! It can be a telescope, a microscope, a submarine periscope, or any other imaging optical system.
Figure 1.5 Paraxial Positive Lens
Figure 1.6 Cardinal Points of an Optical System
12
Chapter 1 The easiest way to imagine what we have here is to think of having a shoebox with a 2-in-diameter hole in each end and inside is some arbitrary optical system (or perhaps nothing at all!). If we send a laser beam into the shoebox through the center of the left-hand hole normal to the hole, it will likely exit through the center of the hole at the other end of the shoebox. The line going through the center of each of the holes is the optical axis. If we now send the laser beam into the shoebox displaced nearly 1 in vertically, it may exit the shoebox on the other end exactly the same and parallel to how it entered, in which case there is probably nothing in the shoebox. Alternately, the laser beam may exit the shoebox either descending or ascending (going downhill or uphill). If the laser beam is descending, it will cross the optical axis somewhere to the right of the shoebox, as shown in Fig. 1.6. If we connect the entering laser beam with the exiting laser beam, they will intersect at a location called the second principal plane. This is sometimes called the equivalent refracting surface because this is the location where all of the rays appear to bend about. In a high-peformance lens, this equivalent refracting surface is spherical in shape and is centered at the image. The distance from the second principal plane to the plane where the ray intersects the optical axis is the focal length. If we now send a laser beam into the hole on the right parallel to the optical axis and in a direction from right to left, it will exit either ascending or descending (as previously), and we can once again locate the principal plane, this time the first principal plane, and determine the focal length. Interestingly, the focal length of a lens system used in air is identical whether light enters from the left or the right. Figure 1.7a shows a telephoto lens whose focal length is labeled. Recall that we can compute the focal length by extending the marginal ray back from the image until it intersects the incoming ray, and this distance is the focal length. In the telephoto lens the focal length is longer than the physical length of the lens, as shown. Now consider Fig. 1.7b, where we have taken the telephoto lens and simply reversed it with no changes to radii or other lens parameters. Once again, the intersection of the incoming marginal ray with the ray extending forward from the image is the focal length. The construction in Fig. 1.7b shows clearly that the focal lengths are identical with the lens in either orientation! The center of the principal planes (where the principal planes cross the optical axis) are called the nodal points, and for a system used in air, these points lie on the principal planes. These nodal points have the unique property that light directed at the front nodal point will exit
Basic Optics and Optical System Specifications
13
Figure 1.7 The Identical Lens Showing How the Focal Length Is Identical When the Lens Is Reversed
the lens from the second nodal point at exactly the same angle with respect to the optical axis. This, too, we can demonstrate with our laser beam and shoebox. So far, we have not talked about an object or an image at all. We can describe or represent a cone of light leaving an object (at the height, Y, in Fig. 1.6.) as including the ray parallel to the optical axis, the ray aimed at the front nodal point, and lastly the ray leaving the object and passing through the focal point on the left side of the lens. All three of these rays (or laser beams) will come together once again to the right of the lens a distance, Y ′, from the optical axis, as shown. We will not bore you with the derivation, but rest assured that it does happen this way. What is interesting about this little example is that our shoebox could contain virtually any kind of optical system, and all of the preceding will hold true. In the case where the laser beam entering parallel to the optical axis exits perhaps at a different distance from the axis but parallel to the axis, we then have what is called an afocal lens such as a laser beam expander, an astronomical telescope, or perhaps a binocular. An afocal lens has an infinite focal length, meaning that both the object and the image are at infinity.
Useful First-Order Relationships As discussed earlier, in first-order optics, lenses can be represented by planes where all of the bending or refraction takes place. Aberrations are
14
Chapter 1
Figure 1.8 Newton’s Equation
nonexistent in first-order optics, and the imagery is by definition absolutely perfect. There are a series of first-order relationships or equations, which come in very handy in one’s everyday work, and we will discuss the most useful ones here. Consider the simple lens system shown in Fig. 1.8. Newton’s equation says: (x)(x′) ƒ2 where x is the distance from the focal point on the front side of the lens to the object, and x′ is the distance from the rear focal point to the image. Note that x is negative according to the sign convention, since the distance from the image to the object is in a direction to the left. This is an interesting equation in that, at first glance, it seems to be of marginal use. However, consider the example where we need to determine how far to refocus a 50-mm focal length lens for an object at a distance of 25 m. The result is 0.1 mm, and this is, in all likelihood, a very reliable and accurate answer. We must always remember, however, that first-order optics is an approximation and assumes no aberrations whatsoever. For small angles and large ƒ/#s the results are generally reliable; however, as the angles of incidence on surfaces increase, the results become less reliable. Consider Fig. 1.9a where we show how light proceeds through a three-element lens known as a Cooke triplet, with the object at infinity. If we were to use Newton’s equation to determine how far to refocus the lens for a relatively close
Basic Optics and Optical System Specifications
15
object distance, as shown in Fig. 1.9b, the resuting amount of refocusing may not be reliable. This is because the ray heights and angles of incidence are different from the infinite object condition, especially at the outer positive elements, as shown in Fig. 1.9c, which is an overlay of the infinite and close object distance layouts. These different ray heights and angles of incidence will cause aberrations, and the net effect is that the result determined by Newton’s equation might not be reliable for predicting where best focus is located Consider a typical ƒ/5 50-mm focal length Cooke triplet lens used at an object distance of 0.5 m. Newton’s equation gives a required refocusing of 2.59 mm from infinity focus, versus 3.02 mm based on optimum image quality, a difference of 0.43 mm. However, for a 10-m object distance, the difference between Newton’s equation and best focus reduces to 0.0008 mm, which is negligible. The important message here is to use first-order optics with caution. If you have any question as to its accuracy in your situation, you really should perform a computer analysis of what you are modeling. If you
Figure 1.9 Light Imaging through a Cooke Triplet for Two Object Distances
16
Chapter 1 then find that your first-order analysis is sufficiently accurate, continue to use it with confidence in similar situations. However, if you find inaccuracies, you may need to work with real rays in your computer model. Another useful and commonly used equation is 1 1 1 ƒ s s′ where s and s ′ are the object and image distances, respectively, as shown in Fig. 1.10. Consider now the basic definitions of magnification from an object to an image. In Fig. 1.11, we show how lateral magnification is defined. Lateral implies in the plane of the object or the image, and lateral magnification is therefore the image height, y′ divided by the object height, y. It is also the image distance, s ′, divided by the object distance, s. There is another form of magnification: the longitudinal magnification. This is the magnification along the optical axis. This may be a difficult concept to visualize because the image is always in a given plane. Think of longitudinal magnification this way: if we move the object a distance, d, we need to move the image, d′, where d′/d is the longitudinal magnification. It can be shown that the longitudinal magnification is the square of the lateral magnification, as shown in Fig. 1.12. Thus, if the lateral magnification is 10, the longitudinal magnification is 100. A good
Figure 1.10 Basic Relationship of Object and Image: The “Lens Makers” Equation
Figure 1.11 Lateral Magnification
Basic Optics and Optical System Specifications
17
Figure 1.12 Longitudinal Magnification
example is in the use of an overhead projector where the viewgraph is in the order of 250 mm wide and the screen is in the order of 1 m wide, giving a lateral magnification of 4. If we were to move the viewgraph 25 mm toward the lens, we would need to move the screen outward by 16 25 400 mm. As a further example of the concept, consider Fig. 1.13 where we show a two-mirror reflective system called a Cassegrain. Let us assume that the large or primary mirror is 250 mm in diameter and is ƒ/1. Also, assume that the final image is ƒ/20. The small, or secondary, mirror is, in effect, magnifying the image, which would be formed by the primary mirror by 20 in lateral magnification. Thus, the longitudinal magnification is 400, which is the square of the lateral magnification. Now let us move the secondary mirror 0.1 mm toward the primary mirror. How far does the final image move? The answer is 0.1 400 40 mm to the right. This is a very large amount and it illustrates just how potent the longitudinal magnification really can be. While we are on the subject, how can we easily determine which way the image moves if we move the secondary mirror to the right as discussed previously? Indeed there is an easy way to answer this question (and similar questions). The approach to follow when presented by a question of this kind is to consider moving the component a very large amount, perhaps even to its limit, and ask “what happens?” For example, if we move the secondary mirror to a position approaching the image formed by the primary, clearly the final image will coincide with the secondary mirror surface when it reaches the image formed by the primary. This means that the final image will move in the same direction as the secondary mirror motion. In addition, if you take the secondary and move it a large amount toward the primary, eventually the light will reflect back to the primary when the rays are incident normal to
18
Chapter 1
Figure 1.13 Cassegrain Reflective System
the secondary mirror surface. Moreover, at some intermediate position, the light will exit to the right collimated or parallel. The secret here, and for many other similar questions, is to take the change to the limit. Take it to a large enough magnitude so that the direction of the result becomes fully clear and unambiguous. Figure 1.14 shows how the optical power of a single lens element is defined. The optical power is given by the Greek letter, , and is the reciprocal focal length or 1 divided by the focal length. In optics, we use a lot of reciprocal relationships. Power 1/(focal length), and curvature (1/radius) is another. If we know the radii of the two surfaces, r1 and r2, and the refractive index, n, we find that
1 1 1
(n 1) focal length r1 r2
In addition, if we have two thin lenses separated by an air space of thickness d, we find that 1
a b d ( a b ) focal length One very important constant in the optical system is the optical invariant or Lagrange invariant or Helmholtz invariant. It has a constant value throughout the entire system, on all surfaces and in the spaces between them. The optical invariant defines the system throughput. The basic characteristic of an optical system is known when the two main rays are traced through the system: the marginal ray going from the center of the object through the edge of the aperture stop, and the chief or principal ray
Basic Optics and Optical System Specifications
19
Figure 1.14 Optical Power and Focal Length of a Single Lens Element
going from the edge of the object through the center of the aperture stop. These rays are shown in Fig. 1.15. The optical invariant defines the relationship between the angles and heights of these two rays through the system, and in any location in the optical system it is given as I yp n u y n up where the subscript p refers to the principal ray, no subscript refers to the marginal ray, and n is the refractive index. The optical invariant, I, once computed for a given system, remains constant everywhere within the system. When this formula is used to calculate the optical invariant in the object plane and in the image plane where the marginal ray height is zero, then we get the commonly used form of the optical invariant I hnu h′n′u′ where h, n, and u are the height of the object, the index of refraction, and angle of the marginal ray in the object plane, and h′, n′, and u′ are the corresponding values in the image space. Although this relationship is strictly valid only in the paraxial approximation, it is often used with sufficient accuracy in the form nh sin u n′h′ sin u′ From this form of optical invariant we can derive the magnification of the system M h′/h as n sin u M n′ sin u′
20
Chapter 1
Figure 1.15 The Optical Invariant
In simple terms these relationships tell us that if the optical system magnifies or increases the object M times, the viewing angle will be decreased M times. In systems analysis, the specification of the optical invariant has a significant importance. In the radiometry and photometry of an optical system, the total light flux collected from a uniformly radiating object is proportional to I 2 of the system, commonly known as etendue, where I is the optical invariant. For example, if the optical system is some kind of a projection system that uses a light source, then the projection system with its optical invariant defines the light throughput. It is useful to compare the optical invariant of the light source with the invariant of the system to see how much light can be coupled into the system. It is not necessarily true that the choice of a higher-power light source results in a brighter image. It can happen that the light-source optical invariant is significantly larger than the system optical invariant, and a lot of light is stopped by the system. The implications of the optical invariant and etendue on radiometry and photometry will be discussed in more depth in Chap. 14. The magnification of a visual optical system is generally defined as the ratio of the angles subtended by the object with or looking through the optical system to the angle subtended by the object without the optical system or looking at the object directly with unaided vision. In visual optical systems where the human eye is the detector, a nominal viewing distance without the optical system when the magnification is defined as unity is 250 mm. The reason that unity magnification is defined at a distance of 250 mm is that this is the closest distance that most people with good vision can focus. As you get closer to the object, it subtends a larger angle and hence looks bigger or magnified. This general definition of magnification takes different forms for different types of optical systems. Let us look first at the case of a microscope objective with a CCD camera, as shown in Fig. 1.16. The image from the CCD is brought to the monitor and the observer is located at
Basic Optics and Optical System Specifications
21
the distance, D, from the monitor. The question is what is the magnification of this system. In the first step, a microscope objective images the object with the height, y, onto the CCD camera, with the magnification y′ y where y′ is the image height at the CCD camera. In the next step, the image from the CCD is brought to the monitor with the magnification y″ y′ where y″ is the image height at the monitor. In the third step, the observer watches the monitor from the distance, D, with the magnification 250 mm D Overall, the magnification of this system is y´ y″ 250 M y y′ D y″ 250 M y D The second example is a magnifier or an eyepiece, as shown in Fig. 1.17. The object with height h at a distance of 250 mm is seen to subtend
Figure 1.16 Magnification of a Microscope
22
Chapter 1
Figure 1.17 Magnification of a Magnifier or Eyepiece
an angle, . When the same object is located in the first focal plane of the eyepiece, the eye sees the same object at an angle, , where h 250
h ƒ
Therefore, magnification M is given by 250 M ƒ The next example is the visual microscope shown in Fig. 1.18. A microscope objective is a short focal length lens, which forms a highly magnified image of the object. A visual microscope includes an eyepiece which has its front focal plane coincident with the objective image plane. The image formed by the objective is seen through the eyepiece, which has its magnification defined as 250 Me ƒ where ƒ is the focal length of the eyepiece. The magnification of the microscope is the product of the magnification of the objective times the magnification of the eyepiece. Thus Mm MoMe A visual telescope is shown in Fig. 1.19. A distant object is seen at an angle, , without the telescope and at an angle, , with the telescope. The angular magnification of the telescope is M Using the similarity of triangles, it can also be shown that the telescope magnification is
Basic Optics and Optical System Specifications
23
Figure 1.18 Magnification of a Visual Microscope
Figure 1.19 Magnification of a Visual Telescope
ƒ D M o ƒe d where ƒo is the focal length of the objective, ƒe is the focal length of the eyepiece, D is the diameter of the entrance pupil, and d is the diameter of the exit pupil. There are several useful first-order relationships regarding plane parallel plates in an optical system. The first relates to what happens in an optical system when a wedge is added to a plane parallel plate. If a ray, as shown in Fig. 1.20, goes through the wedged piece of material of index of refraction n and a small wedge angle , the ray deviates from its direction of incidence by the angle, , according to ≈ (n 1) The angle of deviation depends on the wavelength of light, since the index of refraction is dependent on the wavelength. It is important to understand how the wedge can affect the performance of the optical system. When a parallel beam of white light goes through the wedge, the light is dispersed into a rainbow of colors, but the rays of the individual wavelengths remain parallel. Therefore, the formula that gives the angle of deviation through the wedge is used to quickly determine the allowable wedge in protective windows in front of the optical system. However, if the wedge is placed into a converging beam, not only will
24
Chapter 1
Figure 1.20 Light Deviation through Wedged Material
Figure 1.21 Focus Shift Introduced by a Plane Parallel Plate
the different colors be focused at different distances from the optical axis, but also the individual colors will be blurred. There is a term called boresight error, which means the difference between where you think the optical system is looking and where it really is looking. A wedged window with a wedge angle, , will cause a system to have a boresight error of angle . A plane parallel plate in a converging beam moves the image plane further along the optical axis, as shown in Fig. 1.21. If the thickness of the plate is t, the image displacement, d, along the optical axis is
Basic Optics and Optical System Specifications
25
Figure 1.22 Lateral Displacement of a Ray Introduced by a Tilted Plane Parallel Plate
t d (n 1) n When a plane parallel plate is tilted in the optical system, as in Fig. 1.22, then the ray incident at an angle, , is displaced laterally by the amount, , given by t (n 1) n Note that if we look through a telescope at an infinitely distant object and we put a tilted plane parallel plate in front of the telescope, there will be no change in the image. One would think that color fringes would be seen because the different wavelengths are displaced differently. However, because the parallel bundle of rays going through the tilted plate is only laterally displaced, it remains parallel to itself after transmission through the plate, and therefore there is no color fringing. If there is a wedge in the plate, however, chromatic dispersion will, of course, cause the appearance of color fringing.
This page intentionally left blank
CHAPTER
2
Stops and Pupils and Other Basic Principles
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
28
Chapter 2
The Role of the Aperture Stop In an optical system, there are apertures which are usually circular that limit the bundles of rays which go through the optical system. In Fig. 2.1 a classical three-element form of lens known as a Cooke triplet is shown as an example. Take the time to compare the exaggerated layout (Figs. 2.1a and b) with an actual computer optimized design (Fig. 2.1c). From each point in the object only a given group or bundle of rays will go through the optical system. The chief ray, or principal ray, is the central ray in this bundle of rays. The aperture stop is the surface in the system where all of the chief rays from different points in the object cross the optical axis and appear to pivot about. There is usually an iris or a fixed mechanical diaphragm or aperture in the lens at this location. If your lens has an adjustable iris at the stop, its primary purpose is to change the brightness of the image. The chief ray is, for the most part, a mathematical convenience; however, there definitely is a degree of symmetry that makes its use valuable. We generally refer to the specific height of the chief ray on the image as the image height.
Entrance and Exit Pupils The entrance pupil is the image of the aperture stop when viewed from the front of the lens, as shown in Fig. 2.1. Indeed, if you take any telescope, such as a binocular, and illuminate it from the back and look into the optics from the front, you will see a bright disk which is formed, in most cases, at the objective lens at the front of the binocular. In the opposite case, if you illuminate the system from the front, there will be a bright disk formed behind the eyepiece. The image of the aperture stop in the image space is called the exit pupil. If you were to write your initial with a grease pencil on the front of the objective lens and locate a business card at the exit pupil, you would see a clear image of the initial on the card. There is another way to describe entrance and exit pupils. If the chief ray entering the lens is extended without bending or refracting by the lens elements, it will cross the optical axis at the entrance pupil. This is shown in Figs. 2.1a and b where only the chief ray and the pupil locations are shown for clarity. Clearly, it is the image of the aperture stop, since the chief ray crosses the optical axis at the aperture stop. In a
Stops and Pupils and Other Basic Principles
Figure 2.1 Aperture Stop and Pupils in an Optical System
29
30
Chapter 2 similar way, the exit pupil will be at the location where the chief ray appears to have crossed the optical axis. The location of the exit pupil can be obtained if the chief ray that exits the optical system is extended backwards until it crosses the optical axis. Both definitions are synonymous, and it will be valuable to become familiar with each. Let us assume that we have an optical system with a lot of optical components or elements, each of them having a known clear aperture diameter. There are also a few mechanical diaphragms in the system. The question is, which of all these apertures is the aperture stop? In order to answer this question, we have to image each aperture into object space. The aperture whose image is seen from the object plane at the smallest angle is the aperture stop. It is the limiting aperture within the lens. There are many systems such as stand-alone camera lenses, where the location of the entrance and exit pupils are generally not important. The exit pupil location of a camera lens will, of course, dictate the angle of incidence of the off-axis light onto the sensor. However, the specific pupil locations are generally not functionally critical. When multiple groups of lenses are used together, then the pupil locations become very important since the exit pupil of one group must match the entrance pupil location of the following group. This will be discussed later in this chapter.
Vignetting The position of the aperture stop and the entrance and exit pupils is very important in optical systems. Two main reasons will be mentioned here. The first reason is that the correction of aberrations and image quality very much depends on the position of the pupils. This will be discussed in detail later in the book. The second reason is that the amount of light or throughput through the optical system is defined by the pupils and the size of all elements in the optical system. If ray bundles from all points in the field of view fill the aperture stop entirely and are not truncated or clipped by apertures fore or aft of the stop, then there is no vignetting in the system. For a typical lens, light enters the lens on axis (the center of the field of view) through an aperture of diameter D in Fig. 2.2, and focuses down to the center of the field of view. As we go off axis to the maximum field of view, we are now entering the lens at an angle. In order to allow the rays from the entire diameter, D, to proceed through the lens, in which case the aperture stop will be filled with the ray bundle from the edge
Stops and Pupils and Other Basic Principles
31
of the field, the rays at the edge of the pupil have to go through points A and B. At these positions, A and B, the rays undergo severe bending which means that they contribute significantly to the image aberrations of the system, as will be discussed in Chaps. 3 and 5. At the same time, mounting of the lenses with larger diameters is more expensive. Further, the lens will be heavier and thicker. So why don’t we truncate the aperture in the plane of Fig. 2.2 to 0.7D? We will lose approximately 30% of the energy at the edge of the field of view compared to the center of the field; however, the positive elements in our Cooke triplet example will be smaller in diameter, which means that they can also be thinner and the housing can be smaller and lighter in weight. Telescopes, projectors, and other visual optical systems can have vignetting of about 30 to 40%, and the eye can generally “tolerate” this amount of vignetting. When we say that the eye can tolerate 30 to 40% vignetting, what we mean is that a slowly varying brightness over an image of this magnitude is generally not noticed. A good example is in overhead viewgraph and slide projectors where this amount of brightness falloff is common, yet unless it is pointed out, most people simply will not notice. If the film in a 35-mm camera has a large dynamic range, then this magnitude of vignetting is also acceptable in photography. In Fig. 2.3 a triplet lens example is shown first in its original form without vignetting (Fig. 2.3a). In the next step, the elements are sized for 40% vignetting, but with the rays traced as if there is no vignetting (Fig. 2.3b). In the last step, the lens is shown with the vignetted bundle of rays at the edge of the field (Fig. 2.3c). Although vignetting is acceptable and often desirable in visible optical systems, it can be devastating in thermal infrared optical systems because of image anomalies, as will be discussed in Chap. 12. One must also be very careful when specifying vignetting in laser systems, as will be discussed in Chap. 11.
Figure 2.2 Vignetting
32 Figure 2.3 Example of Vignetting
Figure 2.4 Matching of Pupils
Chapter 2
Stops and Pupils and Other Basic Principles
33
When a system is designed using off-the-shelf components with a combination of two or more modules or lens assemblies, it is very important to know the positions of the entrance and exit pupils of these modules. The exit pupil of the first module must coincide with the entrance pupil of the second module, etc. This is shown in Fig. 2.4. There can be a very serious pupil-matching problem when using offthe-shelf (or even custom) zoom lenses as modules in optical systems. Zoom lenses have a given size and position of their pupils which change as a function of zoom position or focal length. It is very easy to make a mistake when the exit pupil of the first module is matched to the entrance pupil of the second module for only one zoom position. When the pupils move with respect to one another through zoom and do not image from one to another, we can lose the entire image.
This page intentionally left blank
CHAPTER
3
Diffraction, Aberrations, and Image Quality
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
36
Chapter 3
What Image Quality Is All About Image quality is never perfect! While it would be very nice if the image of a point object could be formed as a perfect point image, in reality we find that image quality is degraded by either geometrical aberrations and/or diffraction. Figure 3.1 illustrates the situation. The top part of the figure shows a hypothetical lens where you can see that all of the rays do not come to a common focus along the optical axis. Rather, the rays entering the lens at its outer periphery cross the optical axis progressively closer to the lens than those rays entering the lens closer to the optical axis. This is one of the most common and fundamental aberrations, and it is known as spherical aberration. Geometrical aberrations are due to the failure of the lens or optical system to form a perfect geometrical image. These aberrations are fully predictable to many decimal places using standard well-known ray trace equations. If there were no geometrical aberrations of any kind, the image of a point source from infinity is called an Airy disk. The profile of the Airy disk looks like a small gaussian intensity function surrounded by lowintensity rings of energy, as shown in Fig. 3.1, exaggerated.
Figure 3.1 Image Quality, Geometrical Aberrations (Top) and Diffraction Limited (Bottom)
Diffraction, Aberrations, and Image Quality
37
If we have a lens system in which the geometrical aberrations are significantly larger than the theoretical diffraction pattern or blur, then we will see an image dominated by the effect of these geometrical aberrations. If, on the other hand, the geometrical aberrations are much smaller than the diffraction pattern or blur, then we will see an image dominated by the effect of the Airy disk. If we have a situation where the blur diameter from the geometrical aberration is approximately the same size as the theoretical diffraction blur, we will see a somewhat degraded diffraction pattern or Airy disk. Figure 3.1, while exaggerated, does show a situation where the resulting image would, in fact, be a somewhat degraded Airy disk.
What Are Geometrical Aberrations and Where Do They Come From? In the previous section, we have shown the distinction between geometrical aberrations and diffraction. The bottom line is that imagery formed by lenses with spherical surfaces simply is not perfect! We use spherical surfaces primarily because of their ease of manufacture. In Fig. 3.2, we show how a large number of elements can be ground and polished using a common or single tool. The elements are typically mounted to what is called a block. Clearly, the smaller the elements and the shallower the radius, the more elements can be mounted on a given block. The upper tool is typically a spherical steel tool. The grinding and polishing operation consists of a rotation about the vertical axis of the blocked elements along with a swinging motion of the tool from left to right, as indicated by the arrows. The nature of a sphere is that the rate of change of slope is constant everywhere on a sphere, and because of this mathematical definition, the tool and lens surfaces will only be in perfect contact with one another over the full range of motions involved when both are perfectly spherical. Due to asymmetries in the process, the entire surface areas of the elements and tool are not in contact the same period of time. Hence this process is not perfect. However, the lens surfaces are driven to a near-spherical shape in reasonable time by a skilled optician. This is the reason we use spherical surfaces for most lenses. Chapter 17 discusses optical component manufacturing in more detail.
38
Chapter 3
Figure 3.2 Manufacture of Spherical Lens Surfaces
We will discuss the use of nonspherical or aspheric surfaces in Chap. 8. Earlier we said that geometrical aberrations are due entirely to the failure of the lens or optical system to form a perfect geometrical image. Maxwell formulated three conditions that have to be met for the lens to form a perfect geometrical image: 1. All the rays from object point O after passing through the lens, must go through the image point O ′. 2. Every segment of the object plane normal to the optical axis that contains the point O must be imaged as a segment of a plane normal to the optical axis, which contains O ′. 3. The image height, h′, must be a constant multiple of the object height, h, no matter where O is located in the object plane. Violation of the first condition results in the image degradation, or image aberrations. Violation of the second condition results in the presence of image curvature, and violation of the third condition in image distortion. A different way to express the first condition is that all the rays from the object point, O, must have the same optical path length (OPL) to the image point, O ′. OPL
O′(x ′,y ′)
n (s)ds
O (x,y)
where n(s) is the index of refraction at each point along the ray path, s.
39
Diffraction, Aberrations, and Image Quality
The lenses that meet the first Maxwell condition are called stigmatic. Perfect stigmatic lenses are generally stigmatic only for one pair of conjugate on-axis points. If the lens shown in Fig. 3.3 is to be stigmatic not only for the points, O and O ′, but also for the points, P and P′, it must satisfy the Herschel condition u u′ n dz sin2 n′ dz′ sin2 2 2 If the same lens is to be stigmatic at the off-axis conjugate points, Q and Q′, it must satisfy the Abbe sine condition n dy sin u n′ dy′ sin u′ Generally, these two conditions cannot be met exactly and simultaneously. However, if the angles u and u′ are sufficiently small, and we can substitute the sine of the angle with the angle itself sin u ≈ u
and
sin u′≈u′
then both the Herschel and Abbe sine condition are satisfied. We say that the lens works in the paraxial region, and it behaves like a perfect stigmatic lens. The other common definition of paraxial optics is that paraxial rays are rays “infinitely close to the optical axis.” This is a fine and correct definition; however, it can become difficult to understand when we consider tracing a paraxial ray through the edge of a lens system, a long way from the optical axis. This creates a dilemma since rays traced through the edge of the system are hardly infinitely close to the optical axis! This is why the first definition of paraxial optics, i.e., using the small-angle approximation to the ray tracing equations, as would be the case for rays infinitely close to the optical axis, is easier to understand. Consider Fig. 3.4a, where we show how the rays are
Figure 3.3 Definition of Paraxial Lens
40
Chapter 3 refracted at the interface between two optical media, according to Snell’s law. n sin n′ sin ′ In Table 3.1 we show just how a real ray, according to Snell’s law, and a paraxial ray, using the small-angle approximation sin , refract or bend after refraction from a spherical surface at a glass-air interface (index of refraction of glass n 1.5). These data use the nomenclature of Fig. 3.4b. Note that the difference in angle between the paraxial and the real rays define the resulting image blur. For angles of incidence of 10° or less we see that the real refracted ray is descending within 0.1° of the paraxial ray (0.0981° difference at a 10° angle of incidence). However, as the angles of incidence increase, the difference between the real and the paraxial descending angles increases quite significantly. This is where aberrations come from. Along with this understanding, it is evident that in order to keep aberrations small, it is desirable if not mandatory to keep the angles of
Figure 3.4 A Real Ray Trace and a Paraxial Ray Trace through a Lens
TABLE 3.1 Paraxial Approximation Versus Real Ray Angles of Refraction
′ real (degrees)
′ paraxial (degrees)
1
0.5001
0.5
0
10
5.0981
5
0.0981
20
10.8659
10
0.8659
30
18.5904
15
3.5904
40
34.6186
20
14.6186
Difference (degrees)
Diffraction, Aberrations, and Image Quality
41
incidence as small as possible on the various surfaces within your system.
What Is Diffraction? Diffraction is a phenomena or effect resulting from the interaction of light (which of course is electromagnetic radiation) with the sharp limiting edge or aperture of an optical system. While we could very easily fill the next few pages with integral signs and Bessel functions, it is not the intention of the authors to provide this level of detail. Rather, the following explanation is easy to follow and should provide a sufficient level of understanding of the causes of diffraction and resultant observable effects. Imagine a swimming pool at 3 o’clock in the morning with no wind present; the water is like a sheet of glass. Imagine throwing a large rock into one end of the pool. Water waves will emanate outward from where the rock has entered the water as concentric, ever-expanding circles. Before proceeding onward, note that the physics of water waves is virtually identical to the physics of electromagnetic radiation, and all of the derivations are quite analogous. Now let us proceed to the other end of the swimming pool. If the pool is large enough, the water waves will be nearly straight and parallel to one another. In reality, of course, they are going to be curved and centered about the point where the rock entered the water. For this discussion, consider the water waves as straight. Let us now immerse a 1- by 2-m sheet of plywood partially into the pool, as shown at the top of Fig. 3.5. What you will see to a reasonable extent above the edge of the board at the top of Fig. 3.5 is that the water waves will continue to propagate left to right undisturbed. Below the edge where the major part of the board is located, you will see to the right of the board virtually no disturbance in the water. To the right of the intersection of the upper edge of the board and the water waves, you will see little curlicues traveling or emanating outward from the edge of the board. These curlicues are, in reality, diffraction of water waves. We sincerely hope that none of our readers would think there would be a sharp step in the water to the right of the edge…if you did think this was the case, we urge you to try this little experiment in your backyard swimming pool. The peaks of the water waves are called wavefronts. Perpendicular to the wavefronts are the rays. While we rarely if ever talk about “water
42
Chapter 3
Figure 3.5 Diffraction Effects
rays,” we certainly do talk all the time about light rays. The important point here is that the rays are perpendicular or normal to the wavefronts and the wavefronts are perpendicular to the rays. Throughout your reading of this book, we would like you to understand the difference between ray optics and wave optics. Now, back to our little example. If instead of our swimming pool example we were to have parallel or collimated light incident upon the edge of a razor blade, we would have diffraction of the electromagnetic radiation much in the same way as we showed diffraction of water waves. On a distant screen or card you will not see a very sharp edge or step function, but rather an intensity gradient with slight variations in intensity occurring in a similar fashion to the curlicues of the water waves.
Diffraction, Aberrations, and Image Quality
43
The previous explanation represents our attempt to illustrate how diffraction occurs without the lengthy and messy mathematical derivations. If we now have a typical lens system, it is easy to understand that there will, by definition, be a limiting edge or aperture at which the light effectively stops or is blocked. This edge, which in many cases is the aperture stop of your system, wraps around the optical axis generally in a symmetrical, circular fashion, and the resulting diffraction pattern acquires a rotationally symmetric shape known as the “Airy disk.” It is important to note that diffraction occurs perpendicular to an edge. Since a circular aperture, in effect, wraps around in a full 360°, the resulting diffraction pattern (the Airy disk) is a rotationally symmetrical blur. However, if your aperture were a triangular shape as shown in Fig. 3.6a, the resulting diffraction pattern would be star shaped with three spikes as shown in Fig. 3.6c. The reason there are three notable spikes is that the diffraction spreading has occurred perpendicular to the three straight edges of the aperture, as shown in Fig. 3.6b. Note that the relative length of the spikes is proportional to the length of the edge.
Diffraction-Limited Performance As discussed previously, if the geometrical aberrations are significantly smaller than the diffraction blur, the image is, in effect, well represented by the Airy disk. This form of optics is called diffraction-limited optics. Understanding the limits of diffraction-limited optics becomes extremely important, especially with today’s extremely demanding levels of performance. Figure 3.7 shows two very important principles: (1) the physical
Figure 3.6 Diffraction from a Triangular Aperture
44
Chapter 3 diameter of the Airy disk and (2) the angular diameter or subtense of the Airy disk. It can be shown that: Physical diameter of the Airy disk 2.44 ƒ/number Shown in the top part of Fig. 3.7 are three different lenses, all of diameter D. One lens focuses images fairly close to the lens, the second has a somewhat longer focal length, and the third a still longer focal length. For these three lenses, all of which have the same entrance pupil diameter D, the ƒ/# increases in proportion to the increase in focal length. From the equation, we see that the Airy disk increases in diameter in direct proportion to the ƒ/# increase and thus in proportion to the focal length as well. A very useful rule of thumb to remember is: The Airy disk diameter in the visible part of the spectrum is approximately equal to the ƒ/# expressed in microns.
Figure 3.7 A Clarifying Illustration of “DiffractionLimited” Imagery
Diffraction, Aberrations, and Image Quality
45
This is easy to see if you consider a wavelength of 0.5 m, which would be approximately the center of the visible spectrum. In this case, the physical diameter of the Airy disk D 2.44 0.5 ƒ/# 1.22 ƒ/# which is approximately equal to the ƒ/number itself expressed in microns! We now show three separate lenses of diameter D, 2D, and 3D, all of identically the same ƒ/#. What this means is that the Airy disk or diffraction blur will be identical in all three cases. You can see quite clearly that for each lens the focal length increases in proportion to the increase in diameter (since the ƒ/# is identical). What this means is that the angular subtense of the Airy disk also decreases in proportion to the diameter or the increase in focal length. The resulting relationship becomes 2.44 Angular diameter of the Airy disk clear aperture diameter The angular diameter is expressed in radians if the wavelength and the clear aperture diameter are in the same units. Note that in all of the preceding discussion, the diameter of the Airy disk is assumed to be the diameter of the first dark ring in the diffraction pattern.
Derivation of System Specifications There is a broad term “systems analysis” which generally refers to the task of deriving the basic optical system parameters based on the functional system performance requirements. We can apply what we learned earlier to perform a simple, yet noteworthy systems analysis example. Consider, for example, an optical system used in the long-wave infrared (LWIR) which operates in the 8- to 12-m spectral band. Our task is to derive the system ƒ/# and clear aperture diameter. Let us assume that the detector is mercury cadmium telluride or (HgCdTe) with a 50-m pixel pitch and further assume that we need to resolve 0.25 mrad in object space. These values are typical for an LWIR system such as a forward looking infrared (FLIR). Earlier in this chapter, we discussed that as a rule of thumb the smallest resolvable image blur should be matched to the pixel size of the
46
Chapter 3 detector (sensor), i.e., smallest element size. Thus, we would require that the diffraction blur or Airy disk should be approximately the same diameter as our 50-m pixel. Recall that the diameter of the Airy disk, D 2.44 ƒ/#, and we can solve for the ƒ/# to produce a 50-m Airy disk diameter, and the result is ƒ/2.2 at 10 m. Before we continue, it is interesting to note that for diffraction-limited optics, an ƒ/2.2 system that is 6 mm in diameter will have exactly the same diffraction blur diameter as an ƒ/2.2 system that is 3 m in diameter, and that is 50 m! For a given diffraction blur diameter, as the focal length increases, the angular subtense of the Airy disk decreases proportionally. We can use the relationship that the angular diameter of the Airy disk 2.44 /(clear aperture diameter) to solve for the clear aperture diameter required so that the 50-m Airy disk subtends 0.25 mrad in object space, and the result is a 100-mm-diameter clear aperture. Figure 3.8 shows parametrically how the ƒ/# and clear aperture diameters relate to the diffraction-limited image blur or Airy disk diameter and the angular subtense of the diffraction blur. This illustrates how we can quickly and easily take the most basic system functional requirements and derive the system ƒ/# and clear aperture diameters. Do keep in mind that this assumes diffraction-limited optics. Further, it is based on the criteria that the Airy disk is matched to the pixel pitch. These are generally good assumptions to work with, and as your system needs become better understood, you may need to revise the results. As we begin to learn more about image formation, it is important to understand just how light bends or refracts when passing through an air-glass or glass-air interface. As shown in Fig. 3.9, the refractive index of a material n, where n is the ratio of the velocity of light in a vacuum to the velocity of light in the denser material such as glass. Since the light or electromagnetic radiation slows down in the denser material, the refractive index is always greater than unity. For optical glass the refractive index ranges from about n 1.5 to n 1.85. According to the Snell’s law, n sin n′ sin ′. With air on the input side of the interface, the equation reduces to sin n′ sin ′. For small angles the equation further reduces to n′′. We will use this result later! We discussed earlier how light could be represented by either rays or wavefronts, where the two are orthogonal to one another. We will be using both representations throughout this book and we hope that you will become “bilingual” or fluent with both representations. To help understand these concepts, we show in Fig. 3.9 how a light ray, as well as a series of wavefronts, is incident on an air-glass interface and how the
Diffraction, Aberrations, and Image Quality
47
Figure 3.8 Example of Systems Analysis
Figure 3.9 Bending of Light at an Optical Surface
light bends or refracts. From ray optics, we can simply use Snell’s law to determine the angle of refraction. Consider how we represent the same thing using wave optics. The wavefronts are traveling from left to right, with their peaks separated by the wavelength of light. As the wavefront enters the denser medium such as glass, its velocity is reduced by 1/n, with the result being that the wavefronts are closer together. There is a fundamental law of physics, which says that the wavefronts must be continuous at the interface between the media. Considering the velocity reduction along with the wavefront continuity requirement, we can see how the entire wavefront is rotated around in a clockwise direction as it proceeds into the denser medium. Interestingly, you can use this construction to rederive Snell’s law!
This page intentionally left blank
CHAPTER
4
The Concept of Optical Path Difference
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
50
Chapter 4
Optical Path Difference (OPD) and The Rayleigh Criteria OPD is an extremely useful measure of the performance of an imaging optical system. If the wavefronts proceeding to a given point image are spherical, concentric, and centered at the point image for a given field of view, then the imagery will be geometrically perfect, or diffraction limited. As shown earlier, the image will then be a perfect Airy disk. This is, in effect, the reverse of our earlier example where we threw a rock into a pool of water to illustrate the wave nature of light and diffraction. If we think of the water waves traveling in reverse to where the rock entered the water, we will emulate light imaging to a point image. By definition, the wavefronts will be perfectly spherical, concentric, and centered where the rock entered the water. Recall also that rays are perpendicular to the wavefronts. It is thus clear that if the wavefronts are spherical, concentric, and centered at a point in the image, then the rays will all come to that same point as defined by the center of curvature of the wavefronts. As we learned earlier, diffraction at the limiting edge of the pupil will create an Airy disk, which is the reason why we do not have a perfect point image. Consider Fig. 4.1 where we show a hypothetical lens with a perfectly spherical reference wavefront and a real wavefront. The real wavefront departs from sphericity due to aberrations induced by the lens. The optical path difference is the difference between the real wavefront and a spherical reference wavefront, which is usually selected to be a near best fit to the aberrated wavefront. One of the reasons the OPD is so valuable a parameter is evident from the Rayleigh criteria. Lord Rayleigh (real name William Strutt, a Nobel Prize winner for discovering the gas argon) showed that An optical instrument would not fall seriously short of the performance possible with an absolutely perfect system if the distance between the longest and shortest paths leading to a selected focus did not exceed one-quarter of a wavelength.
What the Rayleigh criteria say is that if the OPD is less than or equal to one-quarter of a wave (one-quarter of the wavelength of the light), then the performance will be almost indistinguishable from perfect. If this is the case, then the imagery of a point object will be very nearly a
The Concept of Optical Path Difference
51
Figure 4.1 Optical Path Difference (OPD)
perfect Airy disk. This is a very useful tool, and as will become evident, its validity is quite broadly applicable. It is important to note, however, that it is not 100% infallible, and should only be used as a guide or relative measure of the level of optical performance. Figure 4.2 shows the appearance of the image of a point source, which is known as a point-spread function (PSF), for optical path differences of 0 waves (a perfect Airy disk), 0.25 wave, 0.5 wave, and 1.0 wave. Note that the 0.25 wave imagery is qualitatively nearly indistinguishable from the perfect Airy disk. The character of the central maximum is maintained, and the first bright ring is fully intact. As soon as we go to 0.5 wave and above, the imagery is clearly degraded from perfect. Figure 4.3 shows perspective views of the point spread function for the same values of the OPD; however, these data are for spherical aberration rather than coma. Here, too, we can conclude that the 0.25 wave imagery is nearly indistinguishable from perfect. We do see a drop in peak intensity; however, the overall character of the pattern is very similar to the perfect Airy disk.
52
Chapter 4
Figure 4.2 Image of a Point Source with Different Amounts of Peak-toValley Optical Path Difference Due to Coma
Peak-to-Valley and RMS Wavefront Error The OPD as shown here is known as peak-to-valley (P-V) optical path difference. Peak-to-valley is the total difference between the portion of the wavefront closest to the image (leading, or ahead of the reference wavefront) and the farthest lagging portion of the wavefront (lagging, or behind the reference wavefront). Figure 4.4 shows this as the separation between the two dashed reference spheres.
The Concept of Optical Path Difference
Figure 4.3 Image of a Point Source with Different Amounts of Peak-toValley Optical Path Difference Due to Spherical Aberration
Figure 4.4 Peak-to-Valley and rms Wavefront Error
53
54
Chapter 4 There is another term, and that is rms wavefront error. The definition of rms wavefront error is shown in Fig. 4.4 as the square root of the sum of the squares of the OPDs as measured from a best-fit reference spherical wavefront over the total wavefront area. The rms wavefront error represents more of an averaging over the wavefront than the P-V wavefront error. The example shown on the right-hand side of Fig. 4.4 has the same P-V OPD as the left-hand side; however, the rms would be lower. This is because most of the wavefront error, or wavefront distortion, is at the outer periphery of the aperture, and over most of the area of the wavefront, the wavefront is nearly perfect. Consider, for example, a large telescope mirror 3 m in diameter. In order to assure near-diffraction-limited performance, let us assume that the P-V wavefront error is specified as 0.125 wave on the surface. This is the P-V departure from the ideal or perfect surface profile. In reflection, the wavefront departure will be double this value, or 0.25 wave which just meets the Rayleigh criteria. Now let’s further assume that the optical shop produces a mirror which has a P-V surface departure from the nominal of 0.02 wave, with the exception of a small depression the size of a pencil eraser 0.5 wave deep. The mirror is clearly out of spec as the reflected wavefront will have a P-V error of 1.0 wave, which is four times the Rayleigh criteria. However, the area of this small depression in the surface would be 0.0004% of the total mirror area, an almost negligible amount. This will have virtually zero effect on the optical performance of our telescope, and if the scattering from such an error were of concern, we could simply paint the 6-mm-diameter depression with a flat black paint. While there will still be some scattering from the mirror/paint interface, this, too, will be extremely negligible in all but the most demanding applications (such as with space telescopes). The rms wavefront error typically ranges from approximately onefifth to one-third of the P-V error. This ratio is highly dependent on the correlation of the wavefront, where the correlation is the inverse number of bumps over the surface. For a given number of bumps, a lower correlation has greater surface slope errors and conversely if we assume a ratio of 5 between P-V and rms, the Rayleigh criteria of 0.25 wave P-V equates to 0.05 wave rms. Figure 4.5 shows an exaggerated illustration of just how an aberrated wavefront proceeds to an image. This figure reminds us of several key points such as the fact that rays are perpendicular to the wavefront. The peak-to-valley OPD is the maximum deviation from the real wavefront
The Concept of Optical Path Difference
55
Figure 4.5 OPD Showing Wavefronts and Ray Paths
and a spherical reference wavefront, which best fits the real wavefront. While the figure is quite exaggerated, it is drawn to scale and the various factors we have learned about all apply.
The Wave Aberration Polynomial The optical path difference, or the wave aberration function, can be mathematically expressed in the form of a polynomial for rotationally symmetric optical systems. A single ray proceeding from a given point in the object through an optical system is defined by the coordinates in the object plane and its coordinates in the pupil of the system. The wave aberration function can be expressed as a Taylor expansion polynomial in field and pupil coordinates. The wave aberration polynomial can be simplified by using the symmetrical properties of the optical system. In its final form the wave aberration polynomial has two quadratic terms which are not the intrinsic aberrations—they present a focal shift, five terms of the fourth power of the field and pupil coordinates which are primary aberrations,
56
Chapter 4 and sixth, eighth, and tenth, etc., power terms which are higher-order aberrations. In order to obtain the coefficients in the wave aberration polynomial, it is sufficient to trace a small number of rays and then fit the data to the polynomial. To obtain the higher-order aberrations, it is necessary to do finite ray tracing, but the primary ray aberrations can be calculated by a paraxial ray trace. In optical systems with moderate to small apertures and fields, primary aberrations dominate. The wave aberration polynomial, W, or OPD, is of the form W W020 r 2 W111 h r cos W040 r 4 W131 h r 3 cos W222 h r 2 (cos )2 W220 h 2 r 2 W311 h 3 r cos ...(higher-order terms) where h is the height of the object and r and are polar ray coordinates in the pupil (see Fig. 4.6). It can be shown that the ray coordinates in the image plane relative to the perfect image coordinates are proportional to the partial derivatives of the wave aberration polynomial, i.e. ∂W ∂y ´ ∂y
∂W ∂x ´ ∂x
This means that if the OPD or the wave aberration polynomial is known, the ray intersections in the image plane or spot diagrams can be easily calculated. The exponent of the pupil radius term is higher by one in the wave aberration polynomial than in the ray-intercept equations. Thus, for example, third-order spherical aberration affects the image blur diameter in proportion to the cube of the radius of the pupil, whereas the optical path difference is proportional to the fourth power of the pupil radius.
Depth of Focus As we now know, if the optical path difference is less than or equal to 1
4, our system meets the Rayleigh criteria and the system imagery is nearly indistinguishable from perfect. This result can be effectively used to determine just how much defocus is tolerable to maintain diffractionlimited performance.
The Concept of Optical Path Difference
57
Figure 4.6 Nomenclature for Wave Aberration Polynomial
Consider an otherwise perfect optical system, as shown in Fig. 4.7. The solid line in the upper part of Fig. 4.7 represents the nominally perfect spherical wavefront proceeding to the nominal image plane. If we now locate a compass point displaced fore and aft of the nominal image plane and draw two circles which touch the nominal wavefront on the optical axis, these circles will depart from the nominal wavefront along the limiting marginal ray by an amount which is, in effect, the optical path difference. We now adjust the compass point until this displacement from the nominal wavefront is ±0.25 wave. This yields the image plane locations which correspond to one-quarter wave of defocus. The depth of focus which corresponds to an OPD of ±1 4 is ±/(2 n sin2 ) ±2 (ƒ/#)2 An extremely useful rule of thumb is that the depth of focus in the visible is approximately ±(ƒ/#)2, in micrometers. Thus, for an ƒ/4 lens in the visible the depth of focus is approximately ±16 µm. For an ƒ/2 system the depth of focus is approximately ±4 µm, and so on. In the lower
58
Chapter 4
Figure 4.7 Depth of Focus
portion of Fig. 4.7, we show the depth of focus for systems in the visible, the medium-wave infrared (3 to 5 µm), and the long-wave infrared (8 to 12 µm), respectively. This is shown as a function of ƒ/#. It will become very apparent that as the ƒ/# and wavelength increase, the depth of focus increases as well. This increase is linear with wavelength and quadratic with ƒ/#. Do keep in mind that this assumes an otherwise perfect system. If your lens system has some inherent aberrations and/or wavefront errors due to design or manufacturing errors, then it will not be nominally perfect to begin with and you may not be able to allow a full one-quarter wave of depth of focus in image location or defocus before you degrade the performance by the quarter-wave limit.
The Concept of Optical Path Difference
59
There is another term, “depth of field,” which is often confused with depth of focus. Both terms are defined here, which should dispel any further confusion. Depth of focus. The amount of image defocus which corresponds to being out of focus by one-quarter wave. This means that the optical path difference between the real wavefront leaving the exit pupil at its outer periphery and a reference wavefront centered at the nominal image plane is one-quarter of the wavelength of light. Depth of field. This is a term used mostly in photography. What it means is that if you focus a camera at a given distance or range, how much further from the camera and closer to the camera than this distance will objects be in acceptable focus. This is analogous to depth of focus; however, it is not as stringent, and it is directly related to how acceptable the image looks to the eye.
This page intentionally left blank
CHAPTER
5
Review of Specific Geometrical Aberrations and How to Get Rid of Them
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
62
Chapter 5 As discussed in Chap. 3, aberrations are the failure of the optical system to produce a perfect or point image from a point object. The geometry of focusing light using spherical surfaces is simply not perfect, and spherical surfaces are used primarily due to their inherent ease of manufacturing. Many lenses can be ground and polished at the same time, as was shown in Fig. 3.2. Lenses are blocked together on the rotating part of the machine called a “block.” The top part, which is called a tool, has the desired radius of curvature, and it moves back and forth as the block rotates, forming spherical surfaces of the same radius on all lenses. As was discussed, paraxial optics applies Snell’s law using the small angle approximation where the sine of the angles of incidence on surfaces is equal to the angle, in radians. In paraxial optics, there are no aberrations whatsoever, and by definition, the image of a point object is a perfect point image. Aberrations occur because in a real system the angles of incidence are nearly always so large that the paraxial approximation is invalid and this causes the rays not to converge to a single point image. As will be discussed in Chap. 7, the use of nonspherical, or aspheric, surfaces can often help significantly in minimizing, if not eliminating, aberrations. It is important to note that the use of aspherics does not automatically guarantee that the aberrations will be zero; in fact, for the most part, this will not happen. Their use is yet another technique for minimizing and balancing aberrations. There are techniques for manufacturing aspheric surfaces or aspheric lenses such as injection molding of plastic lenses, compression molding of glass, or diamond-turning aspheric surfaces in plastic, some crystals, or metal. Aspheric surfaces are used for additional aberration correction, but for the most part, spherical surfaces are used in optical systems. Aspheric optical components are often expensive, such as diamond-turned surfaces and glass-molded lenses, and not sufficiently accurate, or unstable with a change of temperature such as plastic lenses. There is a class of small lenses used in optical storage applications such as CD read lenses where aspherics are mandatory. These lenses are about the diameter of an aspirin tablet and are compression molded or manufactured by other techniques. In addition, many of today’s digital cameras contain very small lenses (less than 6 to 8 mm in diameter) and glass aspherics are becoming more common in these application areas. The index of refraction of the glass and other transmitting materials is used for making lenses changes with the wavelength of light, a phenomena called dispersion. The result is aberrations which change as a
Review of Specific Geometrical Abberations
63
function of the wavelength. These aberrations are called chromatic aberrations. The image of a point is a superposition of the images for the entire wavelength band or spectral range, each of them blurred with the presence of monochromatic aberrations. With a well-chosen combination of optical parameters such as lens shapes, number of optical elements, and different optical materials, aberrations in real optical systems with large ray angles can be reduced to a minimum or may be able to be eliminated to the level of the diffraction limit.
Spherical Aberration If light is incident on the single lens shown in Fig. 5.1, rays that are infinitely close to the optical axis will come to focus at the paraxial image position. As the ray height above the optical axis at the lens increases, the rays in image space cross the axis or focus closer and closer to the lens. This variation of focus position with aperture is called spherical aberration. The magnitude of this spherical aberration depends on the height of the ray in the entrance pupil. The amount of spherical aberration is proportional to the cube of ray height incident onto the lens. If the spherical aberration is measured along the optical axis, it is called longitudinal spherical aberration. More often, it is measured as a lateral or transverse aberration, and it represents the image blur radius. For a given focal length lens, a lens with twice the diameter will have eight times larger image blur. For a given focal length and aperture of a single lens, spherical aberration is a function of the object distance and bending (shape) of the lens. Also shown in Fig. 5.1 are lenses of different bending. The meaning of the term “lens bending” is that the focal length and hence the power of the lens is maintained while changing the radii of both surfaces. This would be the same as physically bending a lens made of flexible plastic. Spherical aberration is highly dependent on the relative lens bending, as will be discussed later. Another powerful method of controlling spherical aberration is by splitting the optical power into more elements, as shown in the lower portion of Fig. 5.1. By splitting the optical power among several elements, the angles of incidence on each surface can be reduced, resulting
64
Chapter 5
Figure 5.1 Spherical Aberration
in reduced aberrations. As we learned earlier in Chap. 3, reducing the angle of incidence results in a smaller deviation between paraxial rays and real rays, and hence reduced aberrations. Consider Fig. 5.2 where we show a single ƒ/2 lens element with an enormous amount of spherical aberration. The lower part of Fig. 5.2 also shows an ƒ/2 lens; however, in this case the lens is bent for minimum spherical aberration. When the object point is at a finite distance, the shape of the lens changes for minimum spherical aberration. In a symmetrical case, when the distance of the object point from the lens is the same as the distance of the image, an equiconvex lens is the bending which produces minimum spherical aberration. Let’s look further into reducing the spherical aberration by splitting a lens into several elements. The resulting lens will perform the same
Review of Specific Geometrical Abberations
65
Figure 5.2 Spherical Aberration as a Function of Lens Bending
function, keeping the total optical power of the elements the same as of the original lens. We will demonstrate in a simple way how spherical aberration can be reduced by a factor of 2, if the lens is split into two lenses. We will do this in several logical steps: 1. The first step is to start with a lens bent for minimum spherical aberration, and this is shown in Fig. 5.3a for a 25-mm-diameter ƒ/2 lens of BK7 glass. The residual spherical aberration is 913 m from real ray tracing. 2. We now scale the lens up by a factor of 2, as shown in Fig. 5.3b. The focal length of our new lens is twice as large, the diameter is twice as large, and the spherical aberration is also twice as large. Note that when we scale a lens, all parameters with units of length scale by the same factor such as the radii and thickness. The refractive index is unitless, and thus remains unchanged. The spherical aberration is now doubled to 1826 m. 3. We now reduce the aperture of this scaled-up lens by a factor of 2, as shown in Fig. 5.3c. The spherical aberration reduces by the cube
66
Chapter 5
Figure 5.3 Splitting Optical Power to Reduce Spherical Aberration
of the aperture, which means by a factor of 8, which is 228 m. Real ray tracing gives 200 m, which is quite close. Now we have a lens with approximately four times less spherical aberration than the starting point. This new lens has the same aperture as the starting lens, but its focal length is twice as large. 4. Now we add one more identical lens of the same power (same focal length), as in Fig. 5.3d. The spherical aberration is doubled (approximately), but it is twice as small as the aberration of the starting lens. The real ray tracing shows that our final solution has 334 m of spherical aberration, which is 36% of the starting value with a single element of the same focal length. The new configuration consists of two lenses performing the same function as the single starting lens, but having one-half of the spherical aberration. The theoretical result of splitting a single lens into multiple lenses is shown in Fig. 5.4. This result shows that if we split an element into four to five elements, the spherical aberration will reduce to about 10 to 15% of the single-element starting point. As it turns out, when we split power in a real lens, the results are significantly better. This is because the light exiting the first element will be converging, and if the second element is now bent for minimum spherical aberration based on converging incident light, the resulting spherical aberration is reduced
Review of Specific Geometrical Abberations
67
Figure 5.4 Spherical Aberration as a Function of Number of Elements
even further. This way, by introducing even more optical elements, the spherical aberration can be reduced significantly. Figure 5.5 shows the situation. Figure 5.5a represents a single element bent for minimum spherical aberration. Figure 5.5b shows two identical elements as derived previously. Note that the light between the two elements is converging as it enters the second element. Figure 5.5c shows how the second element can more optimally “curl” or bend more strongly so as to minimize the angles of incidence onto its surfaces, thereby reducing the spherical aberration from the design in Fig. 5.5b with the identical elements. It is instructive to consider the design of an ƒ/2, 100-mm focal length lens for minimum spherical aberration with one, two, three, and four components, and we will do this for glasses with refractive indices ranging from 1.52 to 1.95. We will now plot the peak-to-valley optical path difference for all of these cases in Fig. 5.6. The results are quite dramatic. Note that for a single ƒ/2 element with a 100-mm focal length of BK7 glass (refractive index 1.517) the spherical aberration is approximately 40 to 50 waves P-V. Splitting the element into two elements reduces the OPD to about 6 to 8 waves, and splitting it into three elements further reduces it to about 2 waves. And four elements results in about 0.004 wave, a significant reduction. There is a
68
Chapter 5
Figure 5.5 Illustration of How to Achieve a Further Reduction of Spherical Aberration
further reduction in OPD as the refractive index is increased, especially for three and four elements where nearly six orders of magnitude reduction in OPD is achieved by simply increasing the refractive index from 1.5 to 1.9! This is for what we have termed the “classical” solution. This is where each element is bent somewhat more than its predecessor in order to minimize the angles of incidence and thus the overall spherical aberration. As we will see later, there is a configuration which yields an even better solution, and we call this the “optimum” configuration. It is characterized by a negatively powered meniscus first element, and it yields two orders of magnitude less OPD than the classical solution, even at the lower refractive index region.
Review of Specific Geometrical Abberations
69
Figure 5.6 Spherical Aberration as a Function of Number of Elements and Refractive Index
Note that the preceding parametric analysis is based on monochromatic light and was computed only on axis. While this is somewhat of an idealized situation, the insight we have gained into aberration reduction is of major significance and it further enhances our understanding of aberrations and where they come from. However, from the analysis thus far we really do not know just why such a dramatic reduction in the aberration is achieved. Spherical aberration terms in the wave aberration polynomial are the fourth, sixth, eighth, etc., order in terms of the pupil radius. The exponent of the pupil radius term is larger by one in the wave aberration polynomial than in the ray-intercept equations. When we talk about spherical aberration image blur size in the image plane, we talk about third, fifth, seventh, ninth, etc., order in terms of the pupil radius. Let us again look at three component lenses optimized for the smallest
70
Chapter 5 spherical aberration, and compare the lenses from low-index glass n 1.5, and then increase the index up to n 2. The spherical aberration as a function of the index of refraction is shown in Fig. 5.7. The contribution to the third-, fifth-, seventh-, and ninth-order spherical aberration is shown for refractive indices ranging from 1.5 to 2.0. Generally, lower orders of aberration have higher values, and they are predominant in the polynomial. As the index increases to somewhere around n 1.7, the fifth-order spherical aberration changes sign and starts to balance the third-order aberration, so that the overall spherical aberration has a significant drop. Although the spherical aberration changes a lot with the change of the index of the components, there is only an imperceptible change in the shape of the lenses. The surfaces become a little shallower, but the overall shape of the lens remains the same. As a final illustration of what is happening, consider Fig. 5.8 where we show the classical solutions for refractive indices from approximately 1.5 to 1.7. The graphical data is the deviation of the wavefront from perfect as a function of the normalized pupil radius. Note that the OPD decreases from about 2 waves P-V to about 0.25 wave. Figure 5.9 shows the data for refractive indices ranging from 1.8 to 1.95, and we see that the OPD reduces from 0.002 wave to several ten-thousandths of a wave.
Figure 5.7 Third-, Fifth-, Seventh-, and Ninth-Order Spherical Aberration Versus Refractive Index for Three Elements
Review of Specific Geometrical Abberations
71
Figure 5.8 Lens Configuration and Plot of Optical Path Difference for Optimized Lenses of Refractive Index 1.517 to 1.720
In all of these examples the relative shapes of the elements has remained nearly constant. We noted earlier that there is a more optimum solution, and we show the three-element “classical” and optimum solutions along with the plot of optical path difference in Fig. 5.10. We are able to reduce the P-V OPD from 2 waves to less than 0.007 wave by changing the configuration. Both of these configurations use BK7 glass. The reduction in aberration is due to balancing of the fifth-order spherical aberration against the thirdorder, as described previously. We have discussed orders of aberration in several contexts thus far. By carefully evaluating the plot of optical path difference, you can actually see visually the different orders. Consider Fig. 5.11 where we show again the plots of OPD for the “classical” and optimum designs just discussed. However, here we show each of the orders of spherical aberration. Recall that the exponent is one higher than the transverse ray aberration polynomial, so the third-order spherical aberration is proportional to the fourth-order in OPD, and so on. Of course, focus shift is thus quadratic
72
Chapter 5
Figure 5.9 Lens Configuration and Plot of Optical Path Difference for Optimized Lenses of Refractive Index 1.805 to 1.952
in OPD, as we would expect. Note that each time we see an inflection in the data this is equivalent to another order being added. There will almost, by definition, be higher orders than those shown; however, these data show clearly the presence of the different orders and how they tend to balance each other.
Coma When we move away from the optical axis in field of view, the image of a point becomes nonrotationally symmetric. In Fig. 5.12 parallel rays come from an infinitely distant point which does not lie on the optical axis of the lens. They enter the lens at an angle, and they are focused by the lens to a certain height from the optical axis, defined by the field angle and the focal length of the lens. If the lens itself limits the bundles of rays from different points in the field, we say that the aperture stop is located on the lens. Rays that go through the center of the
Review of Specific Geometrical Abberations
73
Figure 5.10 “Classical” and Optimum Solutions with Three Elements for BK7 Glass
aperture stop are called chief rays. There is only one chief ray for each point in the object. Rays that go through the aperture stop and lie in the plane of the drawing are called meridional rays. Rays which do not lie in the meridional plane are called skew rays. A plane perpendicular to the drawing in which lies the chief ray is called the sagittal plane. The meridional and sagittal planes have one common ray, the chief ray. In an optical system coma is defined as the variation of magnification with aperture. Rays that transmit through the lens through different portions of the aperture stop cross the image plane at different heights from the optical axis. In the case of the single positive lens shown in Fig. 5.12, a ray passing through the top and bottom edge portions of the lens converge to a point in the image plane which is further from the optical axis than the point of convergence of other skew rays. The shape of the image of a point as formed by a system with coma has the shape of a comet. The height of the image is usually defined by the position of the chief ray on the image plane. In the presence of coma, most of the light energy is concentrated in the vicinity of the chief ray. Coma is linearly proportional to the field of view and proportional to the square of the aperture.
74
Chapter 5
Figure 5.11 Illustration of the Orders of Wavefront Aberration
Figure 5.12 Coma
When the aperture stop is not on the lens, moving the position of the stop can control the coma. Having greater ray symmetry on the way through the lens about the aperture stop reduces the coma. Figures 5.13 and 5.14 show the aperture stop to the left and the right of the lens, respectively, and it is clear that the off-axis ray bundles have a higher degree of symmetry and hence significantly reduced coma when the stop is to the right of the lens. This is due to the greater symmetry on the first surface, which results in reduced angles of incidence and hence reduced aberration. We can best understand coma by looking at Fig. 5.15, which shows the cause of coma. In the top part of the Fig. 5.15, we show a collimated bundle of light incident obliquely onto a convex surface (we will only consider here the first surface of the lens). Note that the entire bundle is displaced from the normal to the surface, which is shown as a dashed line.
Review of Specific Geometrical Abberations
75
Figure 5.13 Coma with Stop in Front of Lens
Figure 5.14 Reduced Coma with Stop Aft of Lens
Note also that the upper ray is incident onto the lens surface at a very high angle of incidence with respect to the surface normal, and as we know, this results in a significant ray bending or angle of refraction. The angles of incidence decrease rapidly as we transition to the lower portion of the ray bundle. The coma formation in this situation is quite evident. Consider now the lower portion of Fig. 5.15, where we show a light bundle whose central or chief ray is normal to the surface. Now we have greatly reduced angles of incidence and, furthermore, the upper and lower limiting rays are symmetrical with each other. The net effect is that there is no coma contribution from this surface whatsoever, and the residual aberration is the same as spherical aberration.
76
Chapter 5
Figure 5.15 Where Does Coma Come From?
Astigmatism In the presence of astigmatism, rays in the meridional and sagittal planes are not focused at the same distance from the lens. An astigmatic image formed by a positive lens is shown in Fig. 5.16. Rays in the meridional plane focus along the line that is perpendicular to the meridional plane. Rays in the sagittal plane are focused further away from the lens, along the line perpendicular to the sagittal plane. Between the astigmatic foci, the image of a point is blurred. It takes the
Review of Specific Geometrical Abberations
77
Figure 5.16 Astigmatism
shape of an ellipse or circle. The smallest size of the image blur is halfway between two astigmatic foci when it is circular. Astigmatism is linearly proportional to the lens aperture and to the square of the field angle. Astigmatism can be controlled by changing the shape of the lens and its distance from the aperture stop, which limits the size and position of the bundle of rays passing through the lens. A tilted plate in a converging cone of light introduces astigmatism. A weak meniscus lens close to the image plane acts similar to a tilted plate with a tilt angle which changes from zero on axis to a certain angle at the edge of the field. This way, astigmatism created by the meniscus can partly or completely cancel the astigmatism of the rest of the optical system. Also shown in Fig. 5.16 is an example showing just how this works. Where does astigmatism come from? An oblique cone of light incident on a lens is shown in Fig. 5.17. Assume that this element is immersed somewhere in the middle of an optical system. The area or footprint on the surface of the light cone shown extends over more of the surface in the y or tangential direction than in the x or sagittal direction. Recall that the rate of change of slope of a sphere is constant
78
Chapter 5
Figure 5.17 Where Does Astigmatism Come From?
everywhere on the sphere. Thus, the extreme tangential rays see a greater slope change on the surface than the extreme sagittal rays and are hence refracted at greater angles. This causes the tangential ray fan to focus closer to the lens than the sagittal ray fan, and this is astigmatism. As the surface is spherical, we will also find in many cases an off-axis form of spherical aberration called “tangential oblique spherical aberration” which is introduced in the tangential direction.
Field Curvature and the Role of Field Lenses A positive lens forms an image on a curved surface, as shown in Fig. 5.18. In the absence of astigmatism, a surface on which the image is formed is called the Petzval surface. If a lens has no astigmatism, the sagittal and tangential images coincide with each other, and they coincide with the Petzval surface.
Review of Specific Geometrical Abberations
79
Figure 5.18 Field Curvature
In the presence of astigmatism, both sagittal and tangential image planes are closer to the lens than the Petzval surface, and the tangential image is three times further from the Petzval surface than the sagittal image. The curvature of the Petzval image is inversely proportional to the product of the index of refraction of the lens and its focal length. If there are many components in the optical system, the resulting Petzval curvature is a sum of Petzval curvature contributions from all lenses. We know that with a 35-mm camera, we can take nice sharp photographs using a flat film. Which method is then used in designing a lens to get a flat image plane? Since the contribution a lens element makes to the Petzval sum is proportional to its optical power, simply splitting of the elements will not change the field curvature. However, positive and negatively powered components can be combined to reduce the field curvature to zero. When negatively powered lenses are added to the system, the resulting power is also reduced. Fortunately, there is a solution to this problem. The contribution a lens element makes to the system power is proportional to the product of its power and the height of the marginal ray which is the ray going through the edge of the aperture stop. This way, if the position of a negative lens in an optical system is suitably chosen so that its power is substantial, but the height of the marginal ray on the lens is relatively low, its contribution to the overall optical power is relatively low while still having a significant field curvature. Two examples where a negative component is effectively used to reduce a field curvature are shown in Fig. 5.19. The first example is the Cooke triplet. A negative component is located in the middle between two positive lenses. The marginal ray height on both positive lenses is higher than on the negative lens. However, the power of the negative
80
Chapter 5
Figure 5.19 Negatively Powered Elements with Small Value of Y to Flatten Field
lens significantly reduces the field curvature created by the two positive lenses. The second example is a Petzval lens, where the negative component is located very close to the image plane. Its contribution to the power of the whole lens is very small, since the height of the marginal ray is extremely small when the lens is close to the image. If the lens is placed at the image plane, it does not change the overall power of the system. Is there any reason to put the lens at the image plane? Yes, indeed both positive- and negative-powered lenses are often located either in the image plane or very close to it. They are called field lenses. The first case when a lens is located at the image plane or just in front of the image plane is when the negative lens is used as a field flattener to correct the field curvature and flatten the field. This is common in complex wide field of view, fast (low ƒ/#) lenses. How does a negative lens flatten the field? Let us imagine the case of a simple positive lens that forms an image a certain distance from the lens. If we add a block of glass between the lens and the image plane, the image will move away from the lens. The image shift is proportional to the thickness of the glass block. In the case of the negative lens in front of the image plane, ray bundles that focus close to the edge of the field of view pass through the part of the lens where the glass thickness is larger than in the center of the lens. This way image points that are closer to the periphery of the image are shifted away from the focusing lens more than the ones in the center of the field. This results in a flatter image plane. A doublet lens forms a sharp image on a spherical surface shown in Fig. 5.20a. If an achromatic doublet is an objective lens of a telescope, which focuses the image on a reticle, or on a CCD detector, it is desirable to correct the field curvature of the lens. The reticle is usually engraved
Review of Specific Geometrical Abberations
81
on a flat piece of glass, and in the case of a CCD detector, the sensitive area is always flat. When the CCD detector is adjusted for best focus, both the center and the edge of the field are slightly blurred, as in Fig. 5.20b, and the sharpest image is obtained for the intermediate field. Figure 5.20c shows how a field lens in front of the image reduces the field curvature and the image blur at the edge of the field. The other types of field lenses are positive-powered lenses used in the systems with one or more intermediate images and relay optics. A submarine periscope is an example of such a system. The optics is inside a tube, which is 10 m long or even longer, but the diameter of the optics
Figure 5.20 Field Flattener Example: How a Negative Lens Flattens the Field
82
Chapter 5 does not exceed 250 to 300 mm. Another example is an endoscope, which is on a much smaller scale, but with a similar ratio of the system length and diameter. Schematically, these systems are shown in Fig. 5.21a, where lenses labeled O are objective lenses and lenses labeled F are field lenses. What is the function of these positive field lenses? They cannot correct the field curvature; they actually increase the field curvature already introduced by the other positive lenses. If we look at the axial beam shown in the schematic drawing, and assume from the beginning that there are no field lenses (only the O lenses are present), the axial beam will be focused at the first intermediate image plane, then relayed with two lenses to the second intermediate plane, and finally relayed with another two lenses to the final image plane. There is no problem
Figure 5.21 Field Lens Example: How a Positive Lens Reduces Vignetting
Review of Specific Geometrical Abberations
83
with the axial ray bundle. Now consider the beam entering the optical system at an angle. It will be focused at a certain height from the optical axis in the first intermediate image plane. However, the cone of light is so tilted that almost the whole ray bundle is going to miss the two relay lenses, and it will hit the housing. This is called vignetting in the optical system and it reduces the amount of light in the image periphery. If we now add a positive lens in the image plane, it will not do anything to the axial beam, but it will redirect the cone of light coming from the edge of the field into the relay lenses. There will be no vignetting and almost no change in the position and the size of the image. The image brightness is going to be uniform across the field, but the system will have a significant amount of field curvature. The primary purpose of these positive field lenses is to reduce or eliminate the vignetting in the system. There was a paper in 1980 given by Erhard Glatzel of Carl Zeiss in Germany, where he talked about designing lenses in microlithography that imaged a mask onto a 50-mm-diameter silicon wafer at a 5:1 reduction ratio. Microlithography lenses are the most sophisticated lenses in our industry, since they have to resolve submicrometer structures in the flat image, as shown in Fig. 5.22. Glatzel starts from the basic relation for the Petzval sum. Suppose that only one type of glass is used in the entire lens. In order to correct the field curvature, the sum of the powers of all components in the system has to be zero or very close to zero. At the same time, total power of the system has to be positive. The total power is proportional to the sum of weighted powers of the components, where the weighting factor is the normalized height of the marginal ray on the component. Glatzel first analyzes a so-called planar camera lens similar to a double Gauss-type lens. The positive-powered components are the first two and the last two components. The negatively powered components are located in the center of the lens. This power distribution is very similar to a Cooke triplet lens. Below the lens layout, Glatzel plots the contribution to the power sum as well as the weighted power sum from corresponding lens groups above. Petzval curvature in this first lens is not reduced to zero but has a residual of 0.46. In order to reduce the Petzval sum or field curvature, Glatzel forces the central elements to have a more negative optical power. The Petzval sum is lower than in the first example but it is still present. Unfortunately, the radii of the central elements have become quite strong or severe, thus increasing the angles of incidence on their surfaces (especially the short-radius inner concave surfaces), therefore introducing their own aberrations.
84
Chapter 5
Figure 5.22 Reduced Field Curvature Lenses as Described by Glatzel of Carl Zeiss
F = 1.0
F = 1.0 = 0.27
= 0.46
F = 1.0 = 0.14
The final step in the design of the flat-field lithography lens is the addition of a negative group in the front of the whole lens. This group has a very important role. Because of its negative power, it slightly reduces field curvature, but it expands the beam and makes it possible for the following positive group to make a high contribution to the total power of the system. The final lens design has 0.14 of field curvature. While this still has a noticeable result, the net aberration of the system is extremely well corrected. This form of lens still represents the state of the art in lithography optics. While we are discussing this design, we should take a few minutes to look at the design form. After the initial two negative elements in the
Review of Specific Geometrical Abberations
85
front, Glatzel uses four larger single elements to take the diverging light and converge it into the next group. He uses four elements in order to split the power and minimize angles of incidence so as to reduce aberrations. However, note that the second element seems to have most of the positive power, also the first element of this group seems to be quite concentric about the diverging light cone, and it seems to have little or no optical power. We point this out in order to suggest that this element may indeed be able to be removed from the design. This is something that you should always be looking for during the optimization of your design in order to, where possible, simplify the design. It is difficult, if not impossible, to make a definitive judgment on this without working with the specific design data and optimization. It is certainly possible that this element may be canceling some higher-order aberration residual. We show for interest in Fig. 5.23 a 30-element lithography lens from the patent literature. The many lens elements are, of course, used in order to reduce the angles of incidence and thus the residual aberrations. This lens will be extremely difficult to manufacture, assemble, and align due to the large number of surfaces.
Distortion The only aberration that does not result in image blur is distortion. If all other aberrations in the system, except distortion, are corrected, an object point is imaged onto a perfect image point, which is displaced from its paraxial position. The amount of distortion can be expressed either as a lateral displacement in length units or as a percentage of the paraxial image height. Distortion is defined as y yp Distortion yp where y is the height in the image plane and yp is the paraxial height.
Figure 5.23 A 30-Element Lithography Lens from the Patent Literature
86
Chapter 5 Third-order distortion increases with the cube of the field of view. A distorted image of a rectilinear object is shown in Fig. 5.24. Distortion can be positive or pincushion distortion or alternately negative or barrel distortion. For a thin lens with the aperture stop on the lens, distortion is equal to zero. The thickness of a lens and its position relative to the aperture stop determines its contribution to the system distortion. An example of a system where a correction of the distortion is a big challenge is a wide field-of-view eyepiece. Its field of view may be as high as 70°, and its aperture stop, which is the pupil of the eye, can be in the order of 20 mm away from the system. If the object and the image are interchanged, the lens that has a barrel distortion in one direction has a pincushion distortion in the opposite direction. This is a very interesting subtlety, and we urge the reader to spend due time thinking about it prior to predicting what a distorted image will look like to make sure your sign of distortion is modeling the real world properly. Figure 5.25 shows different amounts of negative and positive distortion. Since distortion is a cosmetic-type aberration not affecting
Figure 5.24 Distortion
Review of Specific Geometrical Abberations
87
Figure 5.25 Illustration of Different Amounts of Negative and Positive Distortion
resolution, its appearance is very important, especially in visual systems. Generally, distortion in the order of 2 to 3% is acceptable visually. Figure 5.26 shows where distortion comes from. In this situation, the aperture stop is located to the left of the lens, and the angle of incidence on the lens by the ray bundle is large enough so that there is a reasonable difference between the paraxial angle of refraction and the real ray angle of refraction. As with spherical aberration, the real rays are refracted more severely than the paraxial rays. In this case, this causes the real image to be pulled inward from the paraxial image thus causing negative or barrel distortion. Table 5.1 summarizes the aperture and field dependence of the primary aberrations.
88
Chapter 5
Figure 5.26 Where Does Distortion Come From?
TABLE 5.1 Summary of ThirdOrder Monochromatic Aberration Dependence on Aperture and Field Angle
Aberration
Aperture Dependence
Field Dependence
Spherical
Cubic
—
Coma
Quadratic
Linear
Astigmatism
Linear
Quadratic
Field curvature
Linear
Quadratic
Distortion
—
Cubic
Axial Color If white light is incident onto a glass wedge or a prism, it is decomposed into a rainbow. This is called dispersion. Blue light is refracted more severely than red light, since the index of refraction is higher for shorter wavelengths than for the longer wavelengths. The properties of lenses also vary with wavelength. White light coming from an axial infinitely distant object, which is incident upon a convergent lens, is shown in Fig. 5.27a. The edge of the lens acts like a wedge, refracting or bending the blue light more than the red light. This causes the blue light to focus closer to the lens than the red light. This longitudinal variation of focus with wavelength is called the axial chromatic aberration or axial color. In the absence of spherical aberration, a system with uncorrected chromatic aberration forms a bright spot surrounded with a purple halo coming from the blue and red light.
Review of Specific Geometrical Abberations
89
Is there a way to correct the axial color? A lens that focuses an infinitely distant object is shown as an example in Fig. 5.27b. In order to bring the blue and the red to focus together, a positive lens must be split into two lenses made of glasses with different dispersions. The first is a positive lens with low dispersion glass. This type of glass is called a crown glass. The second lens has a lower optical power than the first one, so that the total power of the doublet is positive. However, the second lens is made of a high-dispersion glass called a flint glass, which means that it spreads light more with color, and it cancels most of the axial chromatic aberration created by the first lens because of its negative power. This doublet is called an achromatic doublet.
Figure 5.27 Axial Chromatic Aberation
90
Chapter 5
Lateral Color When a lens forms an image of an off-axis point at different heights for different wavelengths, the lens has lateral chromatic aberration or chromatic difference of magnification. This aberration is quite common in wide field-of-view systems. A very descriptive name for lateral color is color fringing since this is what is seen when looking at an image formed by a lens with lateral color. Lenses that are further from the aperture stop in a system contribute more to lateral color than the lenses with smaller chief ray heights. Lateral color created by a lens is shown in Fig. 5.28. The chief ray is going through the single-lens element close to its outer periphery. Shorter wavelengths are bent or refracted more severely than the longer wavelengths. The blue image is formed closer to the optical axis than the red image. In wide field-of-view systems, lateral color is often the aberration that is the most difficult to correct. Its correction may require the use of anomalous dispersion glasses, which are often expensive, or diffractive elements. Visual systems often have lateral color due primarily to the eyepiece, which inherently has a lot of lateral color. If you look, for example, through a pair of binoculars at a sharp bright/dark edge close to and tangent to the edge of the field of view, you will likely see severe lateral color. This is often not a problem, as the user will most often place the object of interest at the center of the field of view. For this reason visual optical systems tend to be somewhat more forgiving than other systems.
Parametric Analysis of Aberrations Introduced by Plane Parallel Plates Let us assume that we have a diffraction-limited ƒ/1 lens. What is the spherical aberration introduced by a plane parallel plate inserted in the converging cone between the lens and the image plane? The spherical aberration introduced by the plate increases as a function of the plate thickness. Figure 5.29 shows how the blur diameter due to the spherical aberration changes as a function of the ƒ/# of the lens and the plate thickness. The shaded area is the region where the optical system is diffraction limited. For our ƒ/1 lens, the Airy disk diameter is 1.5 m. If a plane parallel plate of glass 50 mm thick is inserted in the ƒ/1 cone of
Review of Specific Geometrical Abberations
91
Figure 5.28 Off-Axis Lateral Color (Color Fringing)
Figure 5.29 Spherical Aberration of a Plane Glass Plate, Refractive Index 1.517 (BK7)
light, the spherical aberration in the focused image increases to 1.25 mm. The image blur is much larger than the Airy disk, which means that the glass plate significantly degrades the performance. We would have to stop down the aperture of the lens to about ƒ/5 to reduce the size of the image blur to the Airy disk. At the point where the diffraction blur and the aberrations of the glass plate are equal, the glass plate will not have a detrimental effect on the image quality. Third-order spherical aberration, coma, astigmatism, and distortion of a plane parallel plate depend on the index of refraction of the plate, n, and the thickness, d, and they are proportional to (n2 1) d n3
92
Chapter 5 What happens if a plane parallel plate is inserted in a converging cone of light at 45°? If the tilted plate is inserted in a rotationally symmetric optical system in a convergent beam, the optical system is no longer rotationally symmetrical. A result of this is the presence of field aberrations such as coma, astigmatism, and lateral color in the on-axis field position. Let us again assume that we have a diffraction-limited, very fast ƒ/1 lens and we need to split the beam into two beams, one reflected at 90° and the other beam transmitted through the tilted plate beamsplitter. The reflected beam is unchanged after reflection off the plate, but the transmitted beam has on-axis astigmatism introduced by the tilted plate. The thicker the plate, the more astigmatism is present. The blur diameter associated with third-order astigmatism as a function of the thickness of the tilted plate and the ƒ/# of the lens is shown in Fig. 5.30. Is there a way to correct this on-axis astigmatism? There are a few different viable methods of correction. Astigmatism is proportional to the square of the tilt angle, so it is therefore not dependent on the sign of the plate tilt. Thus, astigmatism cannot be compensated with a second plate tilted in the opposite direction from the first plate and in the same plane of tilt. This is shown in Fig. 5.31. However, if the second plate is tilted in a plane which is orthogonal to the plane of tilt of the first plate, the astigmatism can be corrected for the most part. The second method of correction involves the use of a weak spherical surface on the tilted plate or a weak wedge instead of the plane parallel plate. Although it is
Figure 5.30 Third-Order Astigmatism Blur Diameter, in Micron, as a Function of the Thickness of a 45° Tilted BK7 Plate and the ƒ/# of the Lens
Review of Specific Geometrical Abberations
Figure 5.31 Correction of Astigmatism from a Tilted Plate in a Converging Beam
Figure 5.32 Tangential Coma Blur Diameter As a Function of the Thickness of a 45° Tilted Plate of Index 1.5 and the ƒ/# of the Lens
Figure 5.33 Lateral Color Blur Diameter in Microns as a Function of the Thickness of a 45° Tilted BK7 Plate and the ƒ/# of the Lens
93
94
Chapter 5 more difficult for fabrication, a good correction of the astigmatism can be achieved with a decentered cylindrical surface on the tilted plate. You can also think of this component as a wedged cylinder. In this way, the astigmatism, as well as a smaller residual of coma, are reasonably well corrected. The most severe aberration introduced in an optical system by a tilted plate is astigmatism. However, coma and lateral color are also significant in the case of a fast lens even when the plate thickness is less than 1 mm. The residual tangential coma blur in a system with a 45° tilted plate is shown as a function of plate thickness and the ƒ/# of the lens in Fig. 5.32. Lateral color blur in a system with a 45° tilted plate is shown as a function of plate thickness and the ƒ/# of the lens in Fig. 5.33. Note that the lateral color is independent of the ƒ/number. This is because the lateral color is only dependent on the height of the chief rays in the different wavelengths.
CHAPTER
6
Glass Selection (Including Plastics)
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
96
Chapter 6
Material Properties Overview Every optical system works in its own particular wavelength region determined by the spectral characteristics of the light source, the spectral sensitivity of the sensor, as well as any other factors or components which alter the net sensitivity of the system. If an optical system is a visual system, the optical materials must be transmissive between approximately 425 and 675 nm, as determined by the photopic spectral response curve of the human eye. The photopic eye sensitivity is shown in Fig. 6.1. Optical glasses are the most commonly used materials in optical systems. However, there are some optical plastics with good transmission in the visible spectrum that can be injection molded. In high-volume production, this technology is significantly cheaper than classical glass manufacturing methods. Operating temperature range is very important when choosing optical materials. Optical materials change their index of refraction with temperature, and they also expand differently, changing the lens shape and optical power. Optical plastics have approximately one order of magnitude higher coefficient of thermal expansion than glasses. If the temperature in an optical system rises to a few hundred degrees Celsius, plastic materials cannot be used because the plastic will melt. Most optical glasses can withstand temperatures of a few
Figure 6.1 Photopic Spectral Eye Sensitivity Curve
Glass Selection (Including Plastics)
97
hundred degrees Celsius without changing their shape. In illumination systems close to the light source, the temperature can go up to 900°C. In this case, glass optics will melt too. Fused quartz or fused silica is often used in these systems because it can operate at temperatures close to 1000°C. Manufacturers of optical components usually include in their catalogues information about the standard optical materials they use. An example of the general information on optical materials for the visible, near ultraviolet (UV) and near infrared (IR) spectral regions as provided by Melles-Griot is shown in Fig. 6.2.
The Glass Map and Partial Dispersion The refractive index of all optical materials changes as a function of wavelength. The refractive index increases as the wavelength decreases. This means that optical systems with refractive components have chromatic aberrations. In fact, the performance of an optical system is often limited by chromatic aberrations rather than monochromatic aberrations. In the time of Sir Isaac Newton, it was believed that it was not possible to correct chromatic aberrations by combining different types of glasses. Newton thought that the chromatic aberrations of all lenses were proportional to their powers, with the same constant of proportionality for all glasses. This is the reason why Newton built a reflecting telescope. In the eighteenth century, however, it was found that, with the proper choice of glasses and powers, it was possible to design an achromatic doublet, which was chromatically corrected for two wavelengths. Let us consider two thin lenses made from two different glass types and cemented together as shown in Fig. 6.3. We want to find the condition for this doublet to be an achromatic doublet, chromatically corrected for the red C line wavelength 656.27 nm and for the blue F line 486.13 nm. Generally, the crown materials are less dispersive than the flints, and in an achromatic doublet we combine the less dispersive crown as the positive element and the more highly dispersive flint as the negative element. The central wavelength is usually chosen as the d line, which is 587.56 nm. If the power of the first lens is P1 and the second lens P2, then the total power of the doublet is
98 Figure 6.2 Material Properties Overview from Melles-Griot Catalog (Simplified)
Chapter 6
99
Glass Selection (Including Plastics)
Figure 6.3 Focusing of White Light with an Achromatic Doublet from BK7 and SF2 Glasses
P P1 P2 An achromatic doublet will have the same power for the C line wavelength and the F line wavelength if (P1 P2)C (P1 P2)F or n n n2C n2F 1C 1F P1 n1d 1 P2 n2d 1 where P1 and P2 are the powers of two thin lenses at 587.56 nm. The value (nF nC ) is called the main dispersion. The ratio nd 1 V nF n C is called the V number or the Abbe number. The condition for a doublet to be an achromatic doublet becomes P1 P2 V1 V2 From this relation we can obtain the focal lengths of two components of an achromatic doublet as
100
Chapter 6 V1 V 2 f1 f V1 V1 V 2 f2 f V2 where f is the focal length of the doublet. The net result of this is to derive the powers of the less dispersive crown element and the more dispersive flint element, so that the combined doublet focal length in the red and blue wavelengths are the same. When this condition is reached, the central wavelength (green) is defocused slightly toward the lens. In the second half of the eighteenth century, Ernst Abbe worked closely with Otto Schott on testing different types of optical glass and this encouraged the development of new glass types. It was found that the most suitable way to characterize optical glass was the specification of the index of refraction for the d line, nd , and the Abbe number, V, which determines the glass dispersion. Manufacturers of optical glasses provide a glass map or an nd /Vd diagram in which the Abbe number is plotted as the abscissa and the index, nd , as the ordinate. The glass map from the Schott glass catalogue is shown in Fig. 6.4. Schott is the largest manufacturer of glass in the world, but there are other manufacturers, including Hoya, Ohara, Pilkington, Corning, and Sovirel. The nd /V d diagram subdivides the various types of glasses into groups, each having a specific designation such as BK with BK7, BK1, and others. These designations are generally related to the fundamental materials used in the manufacture of the specific group such as LAFN31 which is a lanthanum flint glass. There is also a more general division of glasses into “crown” and “flint” glasses. The crown glasses are the ones with nd 1.60, Vd 50 or nd 1.60, Vd 55; the other glasses are flints. The available refractive indices range from 1.45 to 2 and the V number from 80 to 20. Mathematically, the dependence of refractive index on the wavelength of light can be expressed in a few different ways, but none of the expressions is highly accurate over the entire glass transmission range. These relationships are empirically derived from measured data. The Sellmeier dispersion formula is 1 2 n2 1 2 i2 ci i
and the formula from the 1967 Schott catalogue is
101
Glass Selection (Including Plastics)
Figure 6.4 Schott Glass Map (Abbe Diagram)
A2 A3 A4 A5 n2 A0 A12 2 4 6 8 These are the two most commonly used formulas. Beside these two formulas, the Hartmann and Conrady formulas are also offered in some of the lens design programs. The six constants that characterize glass dispersion vary considerably between glasses, and thus the general shapes of all dispersion curves are different. In addition to the main dispersion (nF nC ), which is the difference between the index of refraction for the blue and for the red line, the “partial dispersion” is also commonly used. Partial dispersion in the blue is the difference in index of refraction between 435.83 and 486.13 nm, and the red partial dispersion is the difference in index of refraction between 653.27 and 852.11 nm. Perhaps even more important is the “relative partial dispersion,” which is the ratio of the partial dispersion and the main dispersion. Generally, the relative partial dispersion is nx ny Px,y nF n C
102
Chapter 6 A glass map with the relative partial dispersion as a function of the Abbe number from the Schott catalogue is given in Fig. 6.5. The derived formulas for the design of an achromatic doublet provide a chromatic correction for F and C wavelengths. However, dependent on the choice of glasses, there will be a residual mismatch of dispersions, resulting in a larger or smaller “secondary spectrum.” This secondary spectrum is the difference in image position between the central wavelength (green or yellow) and the now common blue and red image position. In order to eliminate the secondary spectrum, we should find a pair of glasses with different V values but the same relative partial dispersion. Abbe showed that the majority of glasses, the so-called normal glasses, exhibit an approximately linear relationship between the relative partial dispersion and the Abbe number. Thus Px,y ≈ ax,y bx,y Vd (Px,y )normal which can be clearly seen in the relative partial dispersion map in Fig. 6.5. The reduction of the secondary spectrum requires the use of at least one glass type which does not lie on the (Px,y )normal line. The glasses that lie away from the line of normal glasses are often expensive and may be
Figure 6.5 Relative Partial Dispersion
Glass Selection (Including Plastics)
103
difficult to manufacture. Some of them are shown in the relative dispersion chart in Fig. 6.5. KZFSN4 is seven times more expensive than BK7, LaK8 is eight times, PSK53A is 11 times, and LaSFN30 24 times.
Parametric Examples of Glass Selection In this section we will show how secondary spectrum can be corrected and to which level, with the right choice of glasses. It will also be shown how the spherical aberration and the secondary spectrum of a doublet are dependent on the ƒ/#. These data are shown as parametric analyses. The first parametric study is shown for the case of an ƒ/10 achromatic doublet using different glass combinations. Four doublets will be compared, the first using two normal glasses, and then using anomalous dispersion glasses for one or both of the elements. The first doublet is designed with two normal glasses: BK7 and SF2. It is an ƒ/10 lens with a 100-mm focal length. The ray aberration curves are shown in Fig. 6.6. An
Figure 6.6 Secondary Spectrum Correction As a Function of Glass Selection
104
Chapter 6 explanation of these curves will be given in Chap. 10. The difference in the Abbe numbers between the two glasses should be sufficiently large, so that the shape or the power of each individual component is reasonable. Note that as the Abbe number difference between the two glasses of an achromatic doublet decreases, the relative powers of the positive and negative elements get stronger. This yields greater spherical aberration, as will be seen. F or the ƒ/10 lens the spherical aberration for the central wavelength is very small, the rms spot diameter is less than 1 m. However, both the red and the blue foci are away from the green focus, which means that the secondary spectrum aberration is not corrected. The second achromatic doublet is designed with PSK52 and SSKN8 glasses. SSKN8 is a normal glass, but PSK52 has anomalous dispersion. The green spot diameter is the same as in the case of the first doublet, but the polychromatic spot diameter is slightly smaller because the secondary spectrum is lower. Note here that we have an increase of spherical aberration which changes with wavelength. The blue has positive spherical aberration and the red has negative spherical aberration. This change in spherical aberration with wavelength is called spherochromatism. The third case is a doublet with FK54 and KF9 glasses. Although KF9 is a normal glass, FK54 has an extremely high anomalous dispersion, resulting in a much better secondary spectrum correction than in the previous case. FK54 is over 30 times the cost of standard BK7 glass! The fourth case is a doublet with FK52 and KZFSN4. Both glasses have anomalous dispersions. The polychromatic spot diameter is less than 1 m, and the secondary spectrum is completely corrected. Furthermore, the spherochromatism is extremely well corrected as well. The second parametric study is the analysis of spherical aberration and secondary spectrum correction as a function of the lens ƒ/# for a chosen set of glasses. The first pair of glasses are FK52 and KZFS1, as shown in Fig. 6.7. As demonstrated for an ƒ/10 lens, the secondary spectrum can be very well corrected, since both glasses have anomalous dispersion. The Abbe numbers for these two glasses are very different; however, the relative partial dispersion is not. In the case of the ƒ/2 lens, the spherical aberration is dominant, with the spot diameter close to 200 m. As the ƒ/# increases to ƒ/5, the spot diameter decreases dramatically to about 3 m. Chromatic aberration is more pronounced in this case. As the ƒ/# increases to ƒ/20, both the spherical and the chromatic aberrations are extremely well corrected, and the spot diameter is less than 1 m.
Glass Selection (Including Plastics)
105
Figure 6.7 Spherical Aberration and Secondary Spectrum Correction As a Function of ƒ/#
The second pair of glasses to be considered is LASFN31 and SFL6, as shown in Fig. 6.8. Although these glasses are high-index glasses and have anomalous dispersion, their relative partial dispersion is quite different and the secondary spectrum correction is poor. The difference in the Abbe numbers is not large. This makes it difficult to correct for the spherical aberration too, since we need to correct both aberrations simultaneously, trying to find the optimum balance between the two. In the case of the ƒ/2 lens, the spot diameter is around 400 m. As the ƒ/# increases, the spot diameter decreases to about 2 m at ƒ/20, largely because of the uncorrected secondary spectrum. The third parametric study is done for the case of an ƒ/4 achromatic doublet using different glass combinations but allowing one surface to be aspheric for nearly complete correction of spherical aberration. This allows us to better see the change in residual spherical aberration with wavelength or spherochromatism. Four doublets are compared, with the same glass combination as the first parametric study. Ray aberration curves are shown in Fig. 6.9. In all four cases, the spherical aberration for the central wavelength is almost perfectly corrected with the asphere on
106 Figure 6.8 Spherical Aberration and Secondary Spectrum Correction As a Function of ƒ/#
Figure 6.9 Secondary Spectrum Correction As a Function of Glass Selection with One Aspheric Surface
Chapter 6
Glass Selection (Including Plastics)
107
the front surface of the doublet. The spot diameter is determined by the chromatic blur of the blue and the red wavelength, and the difference between four cases of glass combination is small. Note that the shape of the ray aberration curves for the blue and the red color are similar in all cases.
How to Select Glass Let us imagine that we have to design a wide field-of-view objective that operates in the visible spectrum. We will most likely start with five to seven elements and select a starting configuration based on our prior work, a patent, or we may elect to derive the design from basic principles. In most cases, it is sufficient to optimize a lens for only three wavelengths if the system is a visual system. However, in the case of a large field of view, it is better to work with five wavelengths properly weighted and a larger number of field points because of the potential problems with lateral color correction. At some point in the design, we will start to change the glass types either manually or by varying the glass characteristics automatically in the optical design program, and allowing them to move across the glass map until they settle in the locations which provide the lowest merit function. We will notice that the glasses tend to go from FK, PSK, across SK, LaK, LaSF, to SF. Very rarely a chosen glass will be KF, LLF, LF, or F. Even the glasses, such as BaLF, BaF, or BaSF, are not so often chosen in the optimization process. However, there are some types of glasses that are in the central region of the glass map, such as KzFS and TiF, that are often chosen in the glass optimization process. The reason for this is that, unlike BaF or BaLF glasses, which are the normal glasses, these glasses have anomalous relative partial dispersions and color correction, particularly secondary spectrum, is much easier with these glasses. Generally, glasses in the central region of the glass map (BaLF, BaF, BaSF glasses) are not frequently used because they are normal glasses and secondary spectrum is not easily corrected with them. The other reason is that their V number has a medium value, which means that primary color is not easily corrected either. The exception is KzFS glasses, which have anomalous dispersion. Unfortunately, as will be discussed later, KzFS glasses are not preferred Schott glasses.
108
Chapter 6 Now comes a very important step in the optical design—we have to check many parameters for each glass, including its availability, price, transmission properties, thermal properties, staining, etc., and make sure that the glass choice is the optimum one. Here the most important parameters an optical designer has to consider in the process of glass selection will be described. This will also be covered in Chap. 17 from a manufacturer’s perspective. AVAILABILITY Glasses are divided into three groups: preferred, standard, and inquiry glasses. Preferred glasses are always available. Note that just because a glass is “preferred” does not mean that it is of good optical characteristics or low in cost, nor does it mean that the glass is easy to work in the shop; it only refers to availability. Quick delivery of standard glasses is generally possible as these glasses are generally in inventory. Inquiry glasses are available only on request, and they are normally not in stock. An optical designer should make every effort to design the system with preferred glasses. The optical design software program Zemax contains an option to use only preferred glasses from the Schott catalogue when a system is optimized with the “hammer” optimization and “substitute” glasses are used. This will be illustrated in the case studies in Chap. 21. TRANSMITTANCE Most optical glasses transmit light well in the visible and the near IR wavelength spectrum. However, in the near UV, the light is more or less absorbed by most glasses. If an optical system has to transmit UV light, the most commonly used materials are fused silica and fused quartz. Some optical glasses, such as a few SF glasses, have a reduced transmittance in the deep blue wavelength spectrum, and they have a yellowish appearance. Glass absorption as a function of wavelength is given in glass catalogues for 5- and 25-mm-thick glass plates. INFLUENCE OF STRESS ON THE REFRACTIVE INDEX Optically isotropic glasses become anisotropic through mechanically and thermally induced stress. This means that the s and p polarization components of light undergo refraction with different indices of refraction. High index alkali lead silicate glasses (dense flints) display a relatively large absolute refractive index change with a small stress birefringence. On the other hand, borosilicate glasses (crowns) exhibit a small absolute change in refractive index with a relatively large stress birefringence.
Glass Selection (Including Plastics)
109
If the optical system has to transmit polarized light and has to maintain the state of polarization throughout the system or part of it, the choice of materials is very important. For example, when there is a prism in such a system with a relatively large mass, and there is a source of heat in its proximity, there can be a gradient of temperature inside the prism. It will introduce stress birefringence, and the polarization axis will be rotated inside the prism. In this case a better choice for the prism material should be one of the SF glasses rather than crown glasses. CHEMICAL PROPERTIES Optical glasses acquire their properties through their chemical composition, melting process, and finishing methods. In order to achieve the desired optical properties, optical glasses often exhibit reduced resistance to environmental and chemical influence. There is no single test method sufficient to describe the chemical behavior of all optical glasses. Four characteristics of glass resistance to environmental and chemical influence are given for each type of glass. In the Schott catalogue, glasses are sorted in four groups depending on their climatic resistance, which is the resistance to the influence of water vapor in the air. Water vapor in the air, especially under high relative humidity and high temperature, can cause a change in the glass surface in the form of a cloudy film that generally cannot be wiped off. Glasses are sorted in six groups depending on their stain resistance, which is a resistance to the influence of lightly acidic water without vaporization and possible changes in the glass surface. When the glass is in contact with an acidic aqueous medium, not only can stains appear on the glass surface, but the glass can also be decomposed. Optical glasses are divided into eight groups according to their resistance to acids. The last division of glasses is in four groups according to their resistance to alkalis. THERMAL PROPERTIES Optical glasses have a positive coefficient of thermal expansion, which means that glasses expand with an increase in temperature. The expansion coefficient, , lies between 4 e-6 and 16 e6/K for optical glasses. There are a few things that one should consider when designing an optical system to work in the given temperature range: Thermal expansion or contraction of glass should not be in conflict with the expansion or contraction of the lens housing. The optical system may have to be athermalized, which means that the optical characteristics of the system are unchanged with
110
Chapter 6 a change in the lens shape and index of refraction with temperature change. Change in temperature can cause temperature gradient in glass, and this can result in temperature-induced stress birefringence. Most optical design programs have the capability of system optimization simultaneously at several different temperatures. The programs take into account both the expansion of glass elements and changing of their shape, expansion of the housing and the spacers between lenses, as well as the change of index of refraction of the glass materials.
Plastic Optical Materials In a high-volume production environment, optical components or optical systems require low-cost materials and low-cost fabrication techniques. Plastic optics are used frequently today primarily for this reason. Plastic optical materials also have lighter weight, higher impact resistance, and offer more configuration possibilities than glass materials. Configuration flexibility is one of the greatest advantages of plastic optics. Aspheric lenses and elaborate shapes can be molded, for example, lenses with integral mounting brackets, spacers, and mounting features for easy alignment. There are some issues, however, that must be considered when using plastic as an optical material. The principal disadvantage of plastic is its relatively low heat tolerance. Plastic melts at a much lower temperature than glass. It is less resistant to surface abrasion and chemicals. Adhesion of coatings on plastic is generally lower than on glass because of the limitation on the temperature at which the coatings are deposited, due to a low melting temperature of plastic. Further, the durability of coatings on plastic lenses is less robust than on glass. In addition, coatings on plastic often craze over time. The use of ion-assisted deposition of plastic coatings offers harder and more durable coatings on plastic. The choice of optical plastic materials is very limited, which means that there is not a lot of freedom in the optical design process. A very important limitation is the high thermal coefficient of expansion and a relatively large change in refractive index with temperature. The refractive index of plastic materials decreases with temperature (it increases in
Glass Selection (Including Plastics)
111
glasses), and the change is roughly 50 times greater than in glass. The thermal expansion coefficient of plastic is approximately 10 times higher than that of glass. High-quality optical systems can be designed with a combination of glass and plastic lenses. In a combination with glass components in the system, plastic lenses can reduce the price and complexity of the optical system tremendously. When the optical power is mainly distributed over the glass components in the system, with one or two weak-powered plastic aspheric correctors, optical aberrations, especially distortion in wide field-of-view systems, can be very efficiently removed. Weak-powered plastic elements are used to minimize the effect on focus with temperature change. Plastic optics can be injection molded, compression molded, or fabricated from cast plastic blocks. Fabrication of plastic elements by machining and polishing from cast plastic blocks is economical in the case of large optical elements, where the molding process has severe limitations. Compression molding offers a high degree of accuracy and control of optical parameters. However, injection molding is the most economical process. It offers moderate optical performance, which is acceptable in a lot of applications. Manufacturing of molds is an expensive process, but it pays off in high-volume production. During the system development phase, plastic optics can be very successfully diamond turned for prototyping, since the cost of diamond turning is lower than the cost of the manufacturing of molds. With today’s high-quality diamond turning, the scattering effect from the turning grooves is most often under control, and if you have a good vendor, this should not be of concern for visible applications. Sometimes “postpolishing” is required to remove the turning mark residuals. During the design of systems with plastic elements, the optical designer has to control the shape of the lenses more carefully than for glass elements. The shape (or bending) of the lens should be optimized for a good flow of the plastic material inside the molds. The thickness of the lens should be quite small, and the parting line, which is the line of contact of two molds, should go through the lens material. It is also important to eliminate inflection points on the lens surfaces in the case of compression molding. This limits the available lens shapes, and requires more parameters to be controlled in the optimization process. Additionally, the lens shape and the refractive index change with temperature have to be monitored, or the system has to be optimized for a given temperature range.
112
Chapter 6 A few of the most commonly used plastic materials are acrylic (polymethyl methacrylate), polystyrene, polycarbonate, and COC (cycloolefin copolymer): Acrylic. The most common and important optical plastic material. It has a good clarity and a very good transmission in the visible spectrum, a high Abbe number (55.3), and very good mechanical stability. Acrylic is easy to machine and polish, and it is a good material for injection molding. Polystyrene. Also a good plastic, cheaper than acrylic, but it has a slightly higher absorption in the deep blue spectrum. Its index of refraction (1.59) is higher than that of acrylic but the Abbe number is lower (30.9). It has a lower resistance to ultraviolet radiation and scratches than acrylic. Acrylic and polystyrene make a viable achromatic pair. Polycarbonate. More expensive than acrylic, but it has very high impact strength and a very good performance over a broad temperature range. Polycarbonate is often used for plastic eyeglasses. A common form of polycarbonate in eyeglasses is CR39. COC. A relatively new material in the optics industry, it has many characteristics similar to acrylic. However, its water absorption is much lower and it has a higher heat distortion temperature. COC is also brittle. A new brand name for COC is Zeonex. Comparative properties of optical plastics are shown in Table 6.1.
113
Glass Selection (Including Plastics) TABLE 6.1 Optical and Physical Properties of Optical Plastics
Property
Acrylic
Polystyrene
Index @588 nm
1.49
1.59
1.586
1.533
Abbe#
55.3
30.87
29.9
56.2
10
9
5
dn/dT 10 /°C Linear expansion coefficient/°C Transmission (%) Birefringence Tensile strength (lb/in2)
8.5 6.5 10
12 5
92 Low
6.3 10
5
88 High/low
Polycarbonate
6.8 10
5
90 High/low
COC
6.5 105 91 Low
10,000
6000
9000
8700
HDT at 264 lb/in2 (°C)
92
82
142
120−180
Impact strength (ft-lb/in)
0.3
0.4
5
0.45
Density (g/cm3)
1.2
1.05
1.2
1.02
Water absorption (%)
0.3
0.02
0.15
0.01
Advantages
Disadvantages
High stiffness, hardness, chemical resistance, and low cost
High index and low cost
Excellent impact resistance and high HDT
High stiffness, high HDT, low water absorption
Brittle and heat resistant
UV absorption, birefringence, and low-impact strength
High birefringence, low Abbe #, and poor scratch resistance
Brittle
This page intentionally left blank
CHAPTER
7
Spherical and Aspheric Surfaces
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
116
Chapter 7
Definition of an Aspheric Surface A spherical surface is defined by only one parameter, the radius or curvature of the surface. If the surface is refractive, with different indices of refraction before and after the surface, then the power of the surface is defined by the surface radius and the indices of refraction of the two media. Radius and curvature are reciprocal to one another. Figure 7.1a shows a plano convex lens element with a spherical radius, imaging an axial point from infinity. The spherical aberration is quite evident. The high angle of incidence of the upper limiting ray of approximately 45° to the surface normal causes this ray to refract very strongly and ultimately to cross the axis significantly closer to the lens than rays closer to the optical axis. A spherical surface has the property that the rate of change of the surface slope is exactly the same everywhere on the surface, and thus the aberration is inevitable. Let us consider reducing the slope of the surface toward the outer periphery of the surface in order to flatten the shape in the region surrounding the outer rays. If we make the surface shape gradually flatter as we proceed outward from the optical axis, we can differentially reduce the refracting ray angle so that the net effect is to bring all of the rays to a common focus position, as shown in Fig. 7.1b. Figure 7.1c compares the spherical surface, which is steeper at its edge, with the aspheric surface, which is flatter at its edge. While correction of spherical aberration is not the only application of aspheric surfaces, it is one of the major application areas. Aspheric surfaces cannot be defined with only one curvature over the entire surface because its localized curvature changes across the surface. An aspheric surface is usually defined by an analytical formula, but sometimes it is given in the form of a sag table for coordinate points across the surface. The sag of a surface is shown in Fig. 7.1. The most common form of an aspheric surface is a rotationally symmetric surface with the sag defined as c r2 z ∑air 2i 1 1(1 k)c 2r 2 where c is the base curvature at the vertex, k is a conic constant, r is the radial coordinate measured perpendicularly from the optical axis, and air2i are the higher-order aspheric terms.
Spherical and Aspheric Surfaces
117
Figure 7.1 Comparison of a Spherical and an Aspheric Lens
When an aspheric surface is not rotationally symmetric, it is given either as a biconic surface with two basic curvatures and two conic constants in two orthogonal directions or as an anamorphic asphere, which has additional higher-order terms in two orthogonal directions. Another form of aspheric surface is a toroid or toric. A toroid has, in effect, the shape of a doughnut. If a doughnut were sitting on the table, we all would agree that it had a basic outer diameter. If we now cut the doughnut vertically into two halves and we look at the cut, we see a circle whose diameter is less than the diameter by perhaps a factor of 5 or thereabouts. These two radii define a toroid, the overall outer radius of the doughnut and the smaller cross-sectional radius. If you work with torics in lens design, it is extremely important that you understand fully and completely the definition used by the computer program you are using, so take the time to study the manual in depth in this regard. In addition, if need be, set up a sample to assure that your understanding is correct. While a doughnut is one form of toroid, a football shape is
118
Chapter 7 another, and it is imperative to understand which one your equation is representing, especially if it is to be manufactured.
Conic Surfaces In the case where the higher-order aspheric terms are zero, the aspheric surface takes the form of a rotationally symmetric conic cross section with the sag defined as c r2 z 2r 2 1 1(1 k)c where c is the base curvature at the vertex, k is a conic constant, and r is the radial coordinate of the point on the surface. In Table 7.1, it is shown how a conic surface takes on the following surface types as a function of the conic constant, k, in the sag equation. Figure 7.2 shows five surfaces having different conic constants but the same curvature. Most of us are generally familiar with the surface shapes described. One surface we do not come across often is the oblate ellipsoid, sometimes called the oblate spheroid. This can be thought of as the shape of the Earth as it rotates about its axis. Due to centrifugal force, the diameter is greater at the equator than in the polar direction. The oblate ellipsoid has its foci orthogonal to the optical axis. Conic surfaces, either reflective or refractive, are free of spherical aberration for one particular set of conjugate points. Let us look into a set of different conic surfaces. A spherical surface forms an aberration-free image if the object is at the center of curvature of the surface. An ellipsoid forms an aberration-free image for a pair of real image conjugates
TABLE 7.1 Conic Section Types
Conic Constant k
Surface Type
0
Sphere
k 1
Hyperboloid
k 1
Paraboloid
1 k 0
Ellipsoid
k0
Oblate ellipsoid
Spherical and Aspheric Surfaces
119
Figure 7.2 Conic Surfaces with the Same Curvature and Different Conic Constants
on the same side of the surface and a hyperboloid for conjugates on two different sides of the surface. A parabolic mirror forms a perfect image of a point for an axial object at infinity. This is the reason why parabolic mirrors (sometimes combined with hyperbolic mirrors) are widely used in astronomical optics. When the object point is moved axially from the position of the aberration-free conjugate, a certain amount of spherical aberration is introduced. If the point is moved laterally, other aberrations, such as coma, astigmatism, and field curvature, contribute to image blurring.
Application of Aspheric Surfaces in Reflective and Refractive Systems Aspheric surfaces are widely used and often essential in reflective systems due to the small number of surfaces and typically large apertures. While a complex lens may consist of 18 spherical radii in order to minimize the aberrations, a reflective system can only have two surfaces in most cases. A simple spherical reflecting telescope suffers from spherical aberration and coma. A spherical mirror is shown in Fig. 7.3a. A point object at infinity is focused by the spherical mirror at a distance from the mirror equal to the one-half of the mirror radius, and this distance is the focal length. Third-order spherical aberration results, and the
120
Chapter 7
Figure 7.3 Conic Surfaces for Reflecting Systems
wavefront error or OPD is proportional to the (aperture)4, as described in Chap. 5. A parabolic reflecting telescope is shown in Fig. 7.3b. This is a classic example of how spherical aberration can be corrected. An infinitely distant axial point is imaged to a perfect aberration-free image point. Unfortunately, the image quality degrades quickly when the object is moved off axis. Coma is the aberration that restricts the field of view of the parabolic telescope to a very small field. A very common form of reflecting telescope is the two-mirror Cassegrain telescope, with both mirrors being conic surfaces. The classical Cassegrain telescope has a paraboloidal primary mirror and a hyperboloidal secondary mirror, as shown in Fig. 7.4. f1 is the location of the image which would be formed by the large primary mirror, and ƒ2 is the location of the image of the entire system. Note that the secondary mirror reimages f1 to f2. A similar configuration, called a Ritchey-Chrétien Cassegrain telescope, has both primary and the secondary hyperbolic mirrors. The classical Cassegrain performance is limited by off-axis coma while the Ritchey-Chrétien Cassegrain is, in effect, a coma-free Cassegrain. Its limiting aberration is astigmatism. Another well-known type of telescope is a Schmidt telescope, which is shown in Fig. 7.5. It consists of a spherical mirror with an aspheric corrector plate located at the center of curvature of the mirror. Thirdorder spherical aberration results in a wavefront aberration function proportional to the (aperture)4. If the aperture stop is located at the
Spherical and Aspheric Surfaces
121
center of curvature of the mirror, there is symmetry for all field positions. Apart from the aperture stop being obliquely viewed by the oblique bundle of off-axis rays, the oblique rays are focused in the same manner as the axial bundle. The chief ray is normally incident onto the mirror everywhere in the field of view. The image is formed on a spherical surface, with the image radius equal to one-half the mirror radius. Without any aberration correction, the rays that are closer to the aperture edge are focused closer to the mirror than the paraxial rays. The wavefront distortion, which is proportional to the fourth power of the aperture radius, can be corrected with a wavefront distortion of the opposite sign introduced by the aspheric corrector plate placed in the aperture stop as in Fig. 7.5b to provide effective “parabolization” of the spherical mirror. A fourth-order aspheric deviation from the flat base surface of the glass corrector introduces a negative fourth-order
Figure 7.4 Cassegrain Telescope
Figure 7.5 Schmidt Telescope
122
Chapter 7 wavefront distortion. The aspheric refractive corrector reduces the spherical aberration. However, some chromatic aberration is introduced by the wedged shape at the outer periphery of the corrector, close to the aperture edge. In order to minimize this chromatic aberration, a very weak positive power is added to the corrector, such that the corrector has zero power at 0.7 of its aperture, as shown in Fig. 7.5c. This shape of the corrector is not only the optimum shape for the correction of spherochromatism (the variation of spherical aberration with wavelength), it is also best suitable for manufacturing. The majority of optical systems are based on the use of spherical components because they are easier to manufacture. However, there are cases where aspheric optical components have a significant advantage over spherical ones. In astronomical optics, reflective aspheric components are widely used. Today, with the significant development of new plastic materials, low-cost molded aspheric refractive optics are finding their place in the large consumer market. Precision diamond grinding and compression molding of glass aspheric lenses is also becoming more common. Refractive aspheric lenses are widely used in many kinds of illumination systems, from the condensers in projection systems and microscopes, to street lamps and searchlights. Since in many cases these are not imaging systems, the manufacturing tolerances on these components are somewhat forgiving. In the case where the optical components are not exposed to the heat from the light source, aspheric optical elements can be injection molded. In projection systems, aspheric condensers are often molded glass lenses, mostly from B270 glass. B270 is a very common low-cost glass similar to BK7, which is used extensively in “float glass” for low-cost windows and mirrors. Glasses that are moldable have a lower temperature at which they become soft than the standard optical glasses. Heat generated by the light source, or by the absorption of light by the optical components themselves, is often a severe problem in optical systems and requires the use of heat-resistant materials such as fused silica or fused quartz. Another field where aspherics find their place is in systems for focusing of laser beams, for example, in CD players or data storage systems, when coupling light from a laser diode into a fiber, or when collimating light from laser diode arrays. These applications require high-precision optical components, as well as optically stable components in a given temperature range. The small size of these components makes them easier to mold. Optical plastics are used wherever they are acceptable,
Spherical and Aspheric Surfaces
123
because of the much lower manufacturing costs. However, accurate lens shape and the very good temperature stability of glass aspheric lenses make them a better solution for applications where high precision is required. Glass aspheric lenses are manufacturable in diameters smaller than 25 mm. At diameters greater than 25 mm, aspheric glass lenses become too expensive for high-volume manufacturing. Single-glass biaspheric lenses are used for focusing or collimation of NA 0.5 laser beams with diffraction-limited performance. An infinitely distant object imaged through a planohyperbolic lens is focused to an aberration-free spot. This feature is used in the case of a planohyperbolic fiber lens (the cross section of the fiber has a planohyperbolic shape) to collimate the fast axis of the laser diode arrays, as shown in Fig. 7.6. The distance of the laser diode from the lens is determined by the index of refraction of the lens. Improvements in the quality of injection-molded plastic optics make the use of them possible in camera lenses and projection lenses. The optical design of these kinds of lenses is difficult because many parameters have to be considered such as The location of the component in the lens to minimize the beam size over the plastic component. The shape of the lens to keep the molding parting line inside the component. Athermalization of the lens. In high-performance lenses, plastic components should be away from the aperture stop because it is very difficult to achieve diffraction-limited performance with injection-molded plastic components. However, they can be extremely useful in the correction of field aberrations such as astigmatism, field curvature, and also distortion. Much of the discussion thus far with respect to aspheric surfaces and their benefits has related to the correction of spherical aberration. If an
Figure 7.6 A Planohyperbolic Collimator
124
Chapter 7 aspheric surface is located at or near the aperture stop of a system, it will primarily affect or benefit spherical aberration, which is an axial aberration which, for the most part, carries across the field of view. As aspheric surfaces are located further from the stop, they can help to minimize some or all of the off-axis aberrations such as coma and astigmatism. A good example of the application of an aspheric surface used for astigmatism correction is shown in Fig. 7.7. In Fig. 7.7a, we see a singleelement lens with its aperture stop located far to the left of the lens. If the curved lens surface is spherical, the oblique rays create a footprint on the surface, which is larger in the plane of the figure than the orthogonal plane in/out of the figure. As we discussed in Chap. 5, this tends to refract and pull the rays in the plane of the figure inward from where they would otherwise focus. We now need to ask ourselves what would it take to push the focus position outward and compensate for this inward focus shift. The answer is to create a more negatively powered surface in the plane of the figure at the outer periphery of the lens. This is shown in proper scale in Fig. 7.7b and in an exaggerated form in Fig. 7.7c. This more negatively powered surface shape in the plane of the figure has virtually no effect in the orthogonal plane, hence the highly efficient correction of astigmatism by the aspheric surface. Another common use of aspherics is in the thermal infrared where the cost of materials is extremely high. With the use of aspherics, the number of elements can be reduced to a minimum.
Guidelines in the Use of Aspheric Surfaces The proper usage of aspheric surfaces is extremely important. This includes which surfaces to make aspheric and whether to use a conic section or, alternatively, a higher-order aspheric. The conic sections include paraboloids, hyperboloids, and ellipsoids, as discussed earlier in this chapter. The higher-order terms are surface departures from conic, which are proportional to r4, r6, r8, r10, and so on, where r is the radial distance from the optical axis. The simpler forms of reflective systems, such as the classical Cassegrain (paraboloidal primary, hyperboloidal secondary) and the Ritchey-Chrétien Cassegrain (two hyperboloids), were discussed earlier. The classical Cassegrain is limited by coma and field
Spherical and Aspheric Surfaces
125
Figure 7.7 Correction of Astigmatism with an Aspheric Surface
curvature, and the Ritchey-Chrétien is, in effec t, a coma-free Cassegrain which is limited by astigmatism and field curvature. Once the basic system is set up on your computer, varying the appropriate conic constants is all it takes to reach a viable solution. But how do we decide which surface, or surfaces, in a lens system should be made aspheric, and how do we decide what form of aspheric to use? To answer this question, first consider Fig. 7.8, where we show: (1) the aspheric surface departures from the base spherical surface and (2) the departures from what we call the “nearest sphere” or “best-fit sphere” to the aspheric surface. The nomenclature is shown in the top of Fig. 7.8 with accurate data below. If we now compute for our baseline spherical optical system a plot of the optical path difference, we should look for a form matching the basic profile or character of these data. For example, if the axial OPD plot resembles the form of the sag from the nearest sphere for the r 6 case, then varying the r 6 coefficient on a surface near the aperture stop will likely be beneficial. If we find a sharp increase or decrease in the OPD off axis at the edge of the pupil, then varying a higher-order term or two on a surface away from the stop will likely be beneficial. There are some basic guidelines, and these are listed here:
126
Chapter 7
Figure 7.8 Aspheric Sags from Vertex Sphere (Top) and Best-Fit Sphere (Bottom)
1. Conic surfaces can be used for correcting third-order spherical aberration and other low-order aberrations. 2. If you have a nearly flat surface, then use an r 4 and higher-order terms rather than a conic. 3. If you have at least a somewhat curved surface, then you can use the conic along with higher-order terms if required. 4. It is generally best not to use both a conic and an r 4 surface, as they are mathematically quite similar. This is because the first term of the expansion of a conic is r 4. While they can both literally be used, the optimization process often tends to beat one against the other, yielding artificially large coefficients, and this may have an effect on the convergence of the optimization. 5. Use aspherics beginning with the lower-order terms and working upward as required. If you can stay with conics, this may make testing more manageable. You should be able to assess the need for adding terms based on the character of the OPD plot.
Spherical and Aspheric Surfaces
127
6. It is very dangerous to use a large number of aspheric surfaces, especially with higher-order terms. This is because they will beat against each other. This means that as one surface adopts a certain aspheric profile or contour, it may increase in its asphericity, with its effect cancelled by adjacent surfaces. For example, if the first of two closely located aspheric surfaces has significant surface departure from sphericity, the neighboring aspheric surface could very likely cancel this effect. While the lens may perform well on paper, we now need to manufacture two highly aspheric surfaces, a difficult and expensive task which may not be necessary. 7. If possible, optimize your design first using spherical surfaces, and then use the conic and/or aspheric coefficients in the final stages of optimization. This may help in keeping the asphericities to a more manageable level.
Specification of Aspheric Surfaces It is important to specify an aspheric surface sufficiently enough to convey to the shop both what you want and what you need. The following items are most often included in specifying aspheric surfaces: 1. The surface to be aspheric is labeled aspheric on the component drawing. 2. You should include an equation of the surface shape along with the aspheric coefficients. A small sketch indicating the nomenclature and sign convention is recommended. 3. A table listing the sag as a function of the radial distance from the surface vertex normal to the optical axis, r, is imperative. You should list a sufficient number of data points to adequately sample the surface profile. 4. You should list how close the actual surface must come to the ideal design prescription. The form of this can be “surface to match nominal surface to within four visible fringes (or 0.001 mm) over clear aperture.” 5. You may need to call out higher-frequency surface irregularities and/or surface finish. The higher-frequency irregularities can be called out by indicating the maximum slope departure from
128
Chapter 7 nominal over the surface. Surface finish is normally called out by indicating the rms surface finish, in nanometers. This latter callout is generally used for diamond-turned surfaces, where surface roughness is sometimes a problem or where scattering and off-axis rejection is of major concern such as in space telescopes. 6. You should, if possible, indicate the form of testing to be used. Do keep in mind that the more callouts you list and the more extensive the testing, the more costly your optics will be, and they will likely take longer to manufacture. Your callouts should indicate only what you need functionally for your system to work properly.
CHAPTER
8
Design Forms
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
130
Chapter 8
Introduction In this chapter, we will discuss how we select the proper design form or configuration for both refractive and reflective image-forming systems. We will also consider fold mirrors and prisms since they have a significant influence on the system design configuration. The proper system design form or “configuration” of an optical system is generally the key to a successful design effort. The term “configuration” here means the basic form of the system which includes not only the number of elements, but also the relative optical power and distribution of the elements within the lens system. For example, an achromatic doublet of two cemented elements, as shown in Fig. 8.1a is clearly different in form from a Cooke triplet, which consists of three separated elements, as in Fig. 8.1b, with two outer positive crown elements and a negative flint element at the center. The Cooke triplet can be used over wider fields of view than a doublet due largely to a reasonable degree of symmetry fore and aft of the central element, which is at or near the aperture stop. The doublet and triplet are very different configurations. What if we were to add a single positively powered element immediately following a cemented doublet, as in Fig. 8.1c ? Would the lens configuration be called a triplet? It certainly would not be a Cooke triplet as the symmetry is not present. This is a very different configuration or design form from a Cooke triplet. However, it is, of course, a three-element lens. The same is true for Fig. 8.1d, where we again have three elements, only here the third element is very near to the image and is serving to both flatten the field as well as correct astigmatism. All three of the three-element configurations are quite different in configuration or form, each with their relative advantages. The selection of an optimum configuration prior to initiating a design effort provides the starting point from which the design optimization proceeds. While lens design software has improved significantly over the years, the programs are rarely capable of changing configurations, and never add or delete elements. Most of the time the program will reach an optimum or local minimum in the error function for the input configuration. For more information on the optimization process, see Chap. 9. The configuration selection is driven by many factors. Nearly every system specification can have an influence on the configuration. The major factors influencing the configuration selection are
131
Design Forms
Figure 8.1 Doublets and Triplets
Field of view Performance requirement ƒ/# Packaging requirements Spectral range
System Configurations for Refractive Systems We will review a progression of configurations for lenses in order to illustrate just what differentiates one from another. The following configuration forms are shown in Fig. 8.2. SINGLE-ELEMENT LENS (FIG. 8.2a) A single-lens element has generally poor image quality and a very small field of view. Further, it suffers
132 Figure 8.2 Progression of Configurations
Chapter 8
Design Forms
133 from chromatic aberrations and it can only be used at a high ƒ/#. We often think of a single element as of “magnifying glass quality.” It is important to note that the performance, which may be poor for one application, may be just fine for another. For example, we have stated that a single element generally has poor image quality. This is, for the most part, true for most critical imaging applications such as camera lenses, machine vision optics, and other similar applications. However, if you are looking for a photon collector with little or no image quality requirements, then a single element may be quite adequate for the task. Another good example is the optics used for optical data storage and other microoptics applications. For data storage applications, a laser diode is imaged to a micron or submicron spot diameter. Since the laser is nearly monochromatic (there may be thermally induced shifts in wavelength), the field of view is nearly zero and the scale or size of the system is extremely small, we often find that a single aspheric element is sufficient for the task. LANDSCAPE LENS (FIG. 8.2b) While a landscape lens is also a single element, it has an aperture stop which is remote or separated from the lens itself. Further, the lens is bent or “curled” around the stop for symmetry reasons. This reduces the angles of incidence on the surfaces and thereby reduces off-axis aberrations. Earlier in Chaps. 3 and 5 we discussed in greater depth how minimizing angles of incidence within a lens system reduces aberrations. A landscape lens can have its aperture stop either aft of the element as shown or in front of the element. It can be shown that the aberrations are somewhat reduced if the stop is in front of the lens, and many early box cameras were constructed this way. The landscape lens has chromatic aberration as well as residuals of many of the other third-order aberrations. We show in Fig. 8.3 two forms of landscape lenses, one with the stop aft of the lens and the other with the stop forward of the lens. It can be shown that the performance is slightly improved with the stop in front. Also shown are two photos of the front of an early Kodak Brownie camera with a flat window followed by its aperture stop and finally the lens, which is aft of the stop. ACHROMATIC DOUBLET (FIG. 8.2c) The achromatic doublet is capable of bringing the red and blue wavelengths to a common focus, with the central green or yellow wavelength defocused slightly toward the lens. A typical achromatic doublet has a blur diameter approximately
134
Chapter 8
Figure 8.3 Landscape Lens with Stop Aft and Forward of Lens
25 times smaller than an equivalent single-element lens (based on an ƒ/5 lens in the visible spectral band). A cemented doublet performs well only over a small field of view, and it cannot be used at low ƒ/#s due to higher orders of spherical aberration. In order to balance the inherent third-order spherical aberration of the cemented doublet, one can introduce a small airspace between the elements. This airspace will permit the balancing of fifth-order spherical aberration with the inherent third-order aberration for an
135
Design Forms
improved overall level of performance. Further improvement can be realized by adding an additional element near the image, which can be used as a field flattener, and often it is possible to bend this element to balance and eliminate some or most of the astigmatism. COOKE TRIPLET (FIG. 8.2d) This three-element lens form takes advantage of symmetry in order to minimize the angles of incidence of the rays as they proceed through the lens over the field of view, and hence it is capable of an acceptable level of performance for many applications. The Cooke triplet was first designed in England by H. D. Taylor at the “Cooke and Sons” optical company. The Cooke triplet is the first configuration we have presented in this review that allows for the optimization and balancing of the seven primary, or third-order, aberrations, as well as the control of focal length. There are eight “useful” variables in a Cooke triplet, the six radii and the two airspaces. Element center thicknesses are generally not of significant use in aberration control and, for the most part, element thicknesses that yield reasonable manufacturing ease are best. We can thus control or optimize the following: 1. Spherical aberration 2. Coma 3. Astigmatism 4. Axial color 5. Lateral color 6. Distortion 7. Field curvature 8. Control of the focal length It is important to note that just because we have the same number of useful variables as the number of primary aberrations (along with the focal length), this does not at all mean that the aberrations can be brought to zero or even close to zero. What it means is that for the ƒ/number and focal length is selected, the aberrations can be reasonably well balanced against one another, especially the third-order aberrations. Thus, for example, an ƒ/6 Cooke triplet covering a 10° full field of view over the visible spectrum will likely be capable of a reasonable level of performance. However, an ƒ/1.4 Cooke triplet covering a 30° full field of view will probably provide fair to poor performance, at best. The low ƒ/number will lead to significant spherical aberration residuals, and the
136
Chapter 8 wide field of view will lead to coma, astigmatism, and other off-axis aberrations. ZEISS TESSAR (FIG. 8.2e) The Zeiss Tessar is derived from, and is an improvement upon, the Cooke triplet. Paul Rudolph of Zeiss Jena replaced the original single rear lens in the Cooke triplet with a doublet lens, resulting in a better lens performance, with higher resolution, excellent contrast, and very low levels of distortion. There is a rule of thumb in lens design which says “clip it in the bud.” What is meant here is that the best place to correct or eliminate aberrations is as close to where they are being introduced as possible. In the case of a Cooke triplet we see that the first positive lens element takes collimated light from infinity and bends or converges it into the second negative lens element. The second element takes the slightly converging light and diverges it into the third and positive element. And finally, the third positive element takes the slightly diverging light and bends the rays so as to create the required ƒ/# of the lens. The amount of ray bending or redirection is greatest for the third element than for the first or second elements. Thus, the aberrations introduced by the third element will be greatest as well. This makes the third element an excellent candidate to convert to a doublet. As one of the more difficult aberrations to correct in a Cooke triplet is axial color (change in focal length with wavelength), making the third element a doublet (as in the Tessar) allows for a superior level of correction of this as well as other residual aberrations. Tessar designs can be effectively used at ƒ/numbers down to ƒ/4.5 or somewhat lower, depending on the relative mix and level of lens requirements. Further, as will become apparent, the Cooke triplet forms the basis of many more complex and high-performance configurations. DOUBLE GAUSS (FIG. 8.2f) The double Gauss lens is yet a further extension toward improved performance at lower ƒ/#s and wider fields of view. If we summarize what we have learned thus far, we can see more clearly the evolution of the double Gauss lens. The methodologies learned thus far include splitting optical power to minimize aberrations, using negative-powered elements with smaller beam diameters for field curvature correction as in the Cooke triplet, and using symmetry fore and aft of the aperture stop also for symmetry reasons, thereby minimizing the angles of incidence on the lens surfaces. As we will learn later, symmetry also allows for cancellation of several off-axis aberrations. The double Gauss lens uses at least two negatively powered elements near the stop
Design Forms
137 and two or more positive elements on the outsides. Furthermore, there is a reasonably high level of symmetry surrounding the aperture stop. The double Gauss lens is capable of good performance down to about ƒ/1.4 and even lower. Indeed, there have been several ƒ/1.0 double Gauss lenses in the 35-mm camera marketplace, including the famous Nocitlux designed by Walter Mandler of Ernst Leitz Canada. As with any lens, there are compromises, and at ƒ/1.0 the lens is hardly diffraction limited; however, from an overall performance standpoint and light-gathering capability, the lens is a top performer. We should note that for the more demanding levels of performance (such as the Nocitlux), higher refractive index materials are often used as they can significantly reduce aberrations, as well as anomalous dispersion glasses for superior chromatic aberration correction. Glass selection is discussed in Chap. 6. PETZVAL LENS (FIG. 8.2g) The Petzval lens represents a very different design philosophy. This lens is intended for smaller fields of view and only moderate ƒ/#s such as ƒ/3.5 or slower. The design philosophy here is to use two separated doublets with the power task shared between the two. This yields lower secondary chromatic aberrations than a single doublet of the same net ƒ/#. This form of design is used for high-performance small field-of-view lenses as one might encounter in aerial reconnaissance for example. As noted, the Petzval lens is not well suited for wide-angle applications, as there is little opportunity for symmetry as with the Cooke triplet or the double Gauss. TELEPHOTO LENS (FIG. 8.2h) The telephoto lens is a positive group of elements, followed by and separated from a negative group of elements. As we showed earlier in Fig. 8.1, this form of lens has a focal length longer than the physical length of the lens, hence the name “telephoto.” The ratio of the physical length to the focal length is called the telephoto ratio. In the case of a fast lens (low ƒ/number), with a low telephoto ratio below 0.6, for example, the lens configuration becomes quite complex. In the limit, if the light exits the second group collimated, we have a beam contractor or, in effect, a Galilean telescope, and the focal length is infinite. It is important to note that both the positive and the negative groups generally need to be separately achromatized in order to produce a complete lens with sufficiently low chromatic aberration. It is interesting to think about the use of the words “telephoto lens.” To a photographer a telephoto lens is generally a lens whose focal length is longer than a standard lens for a specific film format. For example, the
138
Chapter 8 standard focal length for a 35-mm camera lens is in the order of 50 to 55 mm. A lens with a 100- to 135-mm focal length or longer is generally considered to be a telephoto lens. This is because objects appear closer due to the smaller field of view covered by the longer focal length lens. An achromatic doublet with a focal length of 135 mm might, to a photographer, also be a telephoto lens because it brings the object closer. However, to a lens designer a telephoto must be of a form or configuration as shown using a positively powered front group and a negatively powered rear group so that the focal length is longer than the physical length of the lens. WIDE-ANGLE LENS (FIG. 8.2i ) A lens covering a substantially wider field of view than a normal lens (in photography, for example) is called a wide-angle lens. Thus, with a standard focal length of 50 to 55 mm in 35mm photography, a wide-angle lens is generally considered to be 35 mm or less. In order to cover the wider fields of view, we often use a strong negatively powered front element or group of elements to bend the rays outward to cover the wider field angles. In order to still image from infinity, the light in the space between the main body of the lens and the front negatively powered group needs to be converging toward the object as seen in Fig. 8.2i. We show the wide-angle lens as having a negatively powered threeelement front group, with a multielement configuration for the prime lens group. What is happening here is that the prime lens group, itself, is covering a smaller field of view, with the field angle increase happening only at the negatively powered front elements. EYEPIECE (FIG. 8.2j ) An eyepiece is used to visually view and magnify the image from a microscope objective or a telescope objective, or alternatively to view a display such as in a head-mounted display system. The eyepiece is a very different configuration of lens system in that the aperture stop is not only quite remote from the main part of the lens, but it is in reality the pupil of the eye. Eyepieces are normally designed by tracing rays from the eye, which is the aperture stop, to the image plane, as shown in Fig. 8.2j. As can be seen in Fig. 8.2j the rays at the extreme field of view are primarily using the outer periphery of the lens elements. Unfortunately, this often results in significant amounts of astigmatism, lateral color, coma, and distortion. These field aberrations can be quite significant and difficult if not impossible to correct for in extremely wide field-of-
139
Design Forms
view eyepieces with 60° field of view or more. The careful use of higherindex glasses combined with one or more aspheric surfaces (if possible) can help to mitigate the problems to some extent. Eyepieces represent a very different configuration form than other lenses discussed thus far.
System Configurations for Reflective Systems As with lenses, reflective or mirror systems can be of many varied configurations. There are, however, some inherent and very basic differences between refractive or lens systems and reflective or mirror systems. Lens systems are most often straight through and use the full clear aperture of the entrance pupil, as shown in the simple telephoto lens example in Fig. 8.4a. Mirrors have the fundamental challenge that they get in each others way as shown in the two-mirror Cassegrain system in Fig. 8.4b. The Cassegrain is the reflective analogy of the telephoto lens described earlier in this chapter. Note that the large objective lens shown as an achromatic doublet is the optical analogy of the large concave mirror
Figure 8.4 Telephoto and Cassegrain Configurations
140
Chapter 8 generally called the primary mirror. Further, the smaller lens in the refracting telephoto lens is the analogy of the small convex mirror in reflective systems, and it is generally called the secondary mirror. Note that both lens and mirror systems are in the form of the telephoto lens and the focal lengths are in fact equal in both systems. The fundamental issue of the mirrors getting in each others’ way in reflective systems leads to many significant differences between reflective and refractive systems. We will review a progression of configurations for reflective systems in order to illustrate just what differentiates one from another. The following configuration forms are shown in Fig. 8.5: PARABOLOID A single parabolic mirror has zero spherical aberration on axis for an infinitely distant object. It is, however, limited by coma off axis. As shown, the image-forming light is often folded out to
Figure 8.5 Reflective Configurations
Design Forms
141 the side via a tilted flat-fold mirror sometimes called a diagonal mirror. In this case it is called a Newtonian telescope. CASSEGRAIN The Cassegrain form of reflective system is perhaps the most common. In its “classical” design form, a parabolic primary mirror and a hyperbolic secondary are used. With this prescription, coma is the limiting aberration and is the same as a single parabolic mirror of the same ƒ/number. An improved level of performance is achieved by allowing the primary mirror to be hyperbolic along with a hyperbolic secondary. This solution is called the Ritchey-Chrétien form of Cassegrain. It is, in effect, a coma-free Cassegrain and is limited only by astigmatism and field curvature. The layout itself is virtually identical for the classical Cassegrain and the Ritchey-Chrétien forms. In most configurations, the Cassegrain has an inward or concave curving image field due to the Petzval contribution of the convex secondary mirror predominating over the concave primary mirror. GREGORIAN A concave parabolic primary mirror with a concave elliptical secondary mirror is the Gregorian form of telescope. In effect, the elliptical secondary mirror reimages the image formed by the primary mirror to its final position aft of the primary, as shown in Fig. 8.5. The Gregorian is not as common as it was some years ago, and the reason for this is that astronomers years ago did not believe that convex aspheric mirrors (as required by the Cassegrain) could be effectively fabricated and tested. With the advent of interferometry and other advances in optical metrology, testing convex aspheric surfaces became more viable and the more compact Cassegrain is now more widely used. MAKSUTOV The Maksutov uses a spherical primary mirror with a spherical weakly powered meniscus glass corrector plate to balance the spherical aberration of the mirror. This system has been popular with amateur astronomers for many years. A variation known as the MaksutovCassegrain locates the corrector closer to the primary, and an aluminized spot at the center of the convex surface acts like a Cassegrain secondary mirror, hence the name Maksutov-Cassegrain. This is the design form used in the well-known Questar telescope for many years. SCHMIDT The Schmidt system uses a thin aspheric corrector plate located at the center of curvature of a spherical primary mirror to effectively correct all orders of spherical aberration. The aperture stop is at
142
Chapter 8 the corrector plate, and is located at the center of curvature of the primary mirror. Due to this geometry, the chief rays at all field angles will be incident onto the primary perpendicular to its surface. To third order, the spherical aberration will be eliminated at all field angles. The image is formed on a spherical image whose radius is equal to the focal length of the primary mirror. Further, the Schmidt system works quite well at low ƒ/numbers, even as low as ƒ/1 or less. The fact that most aberrations are zero is due to what is known as the “Schmidt principal,” which has as its basis the aperture stop being located at the center of curvature of a spherical mirror. It can be shown that in addition to zero spherical aberration, there is no third-order coma, astigmatism, or distortion. The major residual aberration of tangential oblique spherical aberration is due to the ray obliquity on the corrector plate as well as the foreshortening of the entrance pupil at off-axis field angles. The Schmidt principal is an exceptionally powerful technique, which has been successfully applied in the design of many well-corrected optical systems. It is especially useful in wide-angle applications. A variation of the Schmidt, invented by Baker, uses three separated aspheric Schmidt plates for minimization of the off-axis residual aberrations. There is a variation of the Schmidt system known as a shortened Schmidt Cassegrain. In this configuration, we move the corrector plate closer to the primary mirror to a location where the ray bundle diameter is similar to what it would be in a Cassegrain system. Then a convex mirror is mounted on the interior of the corrector plate and the system geometry now resembles a Cassegrain. The fact that the corrector plate and the aperture stop are no longer at the center of curvature of the spherical primary mirror are cause for coma and other off-axis aberrations; however, the overall performance is reasonably good for small fields of view. This form of system is extremely popular in contemporary amateur telescopes due to its robust performance combined with aggressive packaging. BOWERS SCHMIDT This configuration uses a thin corrector plate, which is a shell concentric about the aperture stop. The aperture stop is at the center of curvature of the primary mirror as with the Schmidt telescope. The net result is a level of performance that comes close to the Schmidt telescope but without aspheric surfaces. If an aspheric corrector plate is now located at the aperture stop, the aberration correction becomes incredible. This is because the shell corrector is concentric about the stop, and only the weak aspheric corrector suffers from obliquity effects.
Design Forms
143 HYBRID A hybrid system is a combination of several pure or classical solutions. What we have here is a combination of the following: A multielement corrector group of a diameter equal to the entrance pupil. This near zero power group of elements is typically three to five lens elements and can be of the same glass type with no chromatic aberrations because it is of zero net optical power. The primary purpose of the corrector group is to balance and cancel the spherical aberration of the spherical primary mirror. The bulk of the optical power is from the primary mirror as well as the secondary, which itself is an aluminized area on the aft surface of the corrector group. Finally, there is a field-correcting group just before the image plane. This group of elements can effectively flatten the field of view and correct the residual off-axis aberrations such as coma and astigmatism. The beauty of working with the hybrid system configuration described here is that each functional attribute of the system is quite independent and can be easily understood. The front corrector group corrects the spherical aberration of the primary mirror. The fact that it is of near zero power means that a single glass will produce a result essentially free of chromatic aberration. And the rear field-correcting group can easily flatten the field curvature and simultaneously correct any residual offaxis aberrations, including coma and astigmatism. UNOBSCURED APERTURE SYSTEMS Finally, there is a class of reflective optical systems generally known as “unobscured aperture systems.” These include the three-mirror anastigmat (TMA) as well as other forms of all reflective nonrotationally symmetric optical systems. These systems eliminate the performance degrading and difficult to support secondary mirror of the Cassegrain. However, we sometimes require nonrotationally symmetric aspheric surfaces which are difficult to manufacture and test and which are generally costly. Figure 8.6 shows a typical form of TMA. This configuration is an afocal telescope and is per U.S. patent 5,173,801 by Cook. While the most obvious advantage of a TMA is in the hardware, especially as it relates to not needing to support a secondary mirror as in a Cassegrain form of system, the TMA can have significant advantages with respect to the suppression of unwanted diffracted light. Consider Fig. 8.7 where we show a system form developed for space applications. While there are variations on the basic
144
Chapter 8 theme, the essence of these systems is that they are used to image relatively close to a bright source as might be encountered in a space application when we are looking within several degrees of the sun. The sky is black, yet the intense solar radiation is just outside our field of view. In order to suppress the diffracted light, the aperture stop is reimaged to a location within the system where an aperture stop slightly smaller than that of the reimaged stop can be located so as to block the reimaged scattered light. This is known as a “Lyot stop” (pronounced “Leo,” after the French astronomer Bernard Lyot).
Reflective Systems, Relative Merits No chromatic aberrations. There are no chromatic aberrations whatsoever in all-reflecting systems. According to ray tracing theory and the use of Snell’s law, the refractive index of a mirror is 1.0 for all wavelengths. For this reason reflective optics can be extremely well suited for multispectral applications or situations where refractive materials are either expensive or unavailable. Central obscuration. Since mirrors get in each other’s way, there is often a central obscuration associated with reflective optical systems such as in the Cassegrain configuration. This obscuration affects the net photon throughput, affects the image contrast or
Figure 8.6 Three-Mirror Anastigmat
Design Forms
145
Figure 8.7 Three-Mirror AllReflective System Showing Lyot Stop for Stray Light Suppression
MTF (Chap. 15), and is difficult to mount and align. Needless to say, the support structure for this “secondary mirror” must be of a minimal obscuration to the incoming light, yet it must be strong and robust. Aspheric surfaces required. Due to the limited number of surfaces that can be effectively used in a reflective optical system, there are rarely enough surfaces to allow for minimization of aberrations as with refractive lens systems. For example, a typical double Gauss lens system may consist of seven elements. If there were no cemented elements, we would have 14 radii with which to minimize ray bendings and hence minimize the residual aberrations. In our Cassegrain reflective system configuration, we have only two surfaces, which are far too few for aberration control, thus leading us to require the use of nonspherical surfaces. One has only to ask the question of how a reflective system with 14 mirrors would look to appreciate the difficulty of working effectively with more than two to three mirrors. It is important to realize that aspheric surfaces are not necessarily bad. There are many contemporary methodologies for producing aspheric surfaces on both mirror as well as transmissive lens surfaces. For mirrors, we have ultraprecision machining or diamond turning as the most common.
146
Chapter 8 Small number of elements. The small number of elements together with the baffling issues, and the fact that the mirrors get in each other’s way, limits the field of view of reflective systems to be generally smaller than of the refractive systems. Can be low weight. Reflective systems can, in many cases, be made of aluminum, which is light in weight. Inherently athermalized. Reflective systems, if manufactured of a single material such as aluminum, are generally athermal. In other words, for a uniform temperature increase or decrease, the entire system expands or contracts by an amount dependent on the thermal coefficient of expansion. Since this is a uniform scaling of all system parameters, the image will still be in focus. If multiple materials and/or thermal gradients are used, then a careful assessment of the thermal properties of the imagery is critical. Zerodur is a glass material with almost zero coefficient of thermal expansion, and it is commonly used for large glass mirrors. The important message here is that reflective systems have the potential for being fully athermalized. To convince yourself that all reflective systems manufactured of the same material throughout are indeed athermal, consider the following explanation: Assume that our design is a Cassegrain reflective system where all components, including the mirrors and the support structure, are aluminum. If we heat or cool the system uniformly, then it will uniformly expand or contract according to the thermal coefficient of expansion of the material. This is, in effect, a scaling of the entire system. Imagine a drawing of our reflective system forming a perfectly focused image. Take this drawing to a copy machine and enlarge it by 20%. Now look at the drawing and ask yourself “is it still in focus?” Of course it is! Needless to say, if you have thermal gradients and/or different materials, you system may not be sufficiently athermal, and this may require active or passive athermalization. Stray light susceptibility. Reflective systems are often faced with problems associated with stray light. This stray light is often outof-field light which directly or indirectly reaches the final sensor. The Cassegrain is an example of a system, which needs to be properly baffled to suppress unwanted stray light that may directly go through, missing both mirrors.
147
Design Forms
Refractive Systems, Relative Merits Straight through. The system operates straight through without any central obscuration. This results in a potentially higher photon efficiency with none of the degradations associated with a central obscuration. Spherical surfaces, conventional manufacturing. Since we can add lens elements and use the necessary techniques to minimize aberrations, we can most often use spherical surfaces and thus avoid expensive manufacturing methods often associated with aspheric surfaces. Can add a lot of components. This makes it possible to design highspeed systems with large fields of view. Expensive materials and athermalization problems in the thermal infrared. Refractive systems used in the thermal infrared (the MWIR which is the 3- to 5-µm spectral band and the LWIR which is the 8- to 14-µm spectral band) often require materials that are very expensive and have a high dn/dt. For example, germanium is extremely expensive, and furthermore it has a dn/dt = 0.000396/°C.
Mirrors and Prisms Mirrors and prisms are the optical components used in optical systems to Change the direction of light. Fold an optical system for better packaging. Provide a proper image orientation. Combine or split the optical beams using beamsplitter coatings. Disperse light with wedged prisms. Provide the means for interpupillary distance change in binocular systems. Expand or contract a laser’s beam diameter, etc.
148
Chapter 8 Flat mirrors fold the optical path in a system. Prisms also fold the optical path, except that the reflecting surfaces of the prisms behave like mirrors rigidly mounted with respect to each other. The optical designer has to be careful to leave enough space during the design of the optical system to place the mirrors and prisms where they are needed. Prisms have flat polished surfaces and have no optical power. If prisms are used for the proper image orientation and location, they use refraction at the input and output surfaces and reflection on the intermediate surfaces. Reflection is a total internal reflection if the incident cone of light is small enough and/or the magnitude of the prism angle is such that the condition for the total internal reflection is satisfied for all rays. Otherwise, surfaces are mirror coated. Reflecting prisms are generally designed so that the entering and exit faces are parallel and perpendicular to the optical axis. This means that the prism can be represented as a plane parallel glass plate. The thickness of the glass plate is obtained by unfolding the prism around its reflecting surfaces. Unfolded prisms are shown in the form of a “tunnel diagram.” The Penta prism with its tunnel diagram is shown in Fig. 8.8. We use a tunnel diagram so as to be able to use a single block of glass with no folding of the optical path during the design. The prism of refractive index, n, and the glass thickness, d (thickness of the unfolded prism), has its equivalent path length in air, also called the prism apparent thickness, and is equal to d dapparent n If the prism is inserted in a convergent beam, the image will be shifted by d(n 1) d n Prism thickness and the apparent prism thickness are shown in Fig. 8.9. In the case of mirrors, the optical designer has to leave sufficient space in the optical path for the mirrors to be mounted. Prisms do not introduce aberrations only if they are located in a collimated beam. When the optical designer works on a system which contains, among other powered components, a prism of thickness d, he or she usually designs the system using a block of glass of thickness d because of the simplicity, smaller number of surfaces, and, consequently, faster ray tracing. In the case when the prism is located in a convergent or divergent beam, this block of glass introduces both monochromatic and chromatic aberrations, and
Design Forms
149
Figure 8.8 Penta Prism
Figure 8.9 Prism Thickness and the Apparent Prism Thickness
has to be present during the optimization of the system. The whole process is iterative. The optical designer starts with the rough size of the prism, and optimizes the system with the prism equivalent block of glass. At some point in the design, the designer checks the diameter of the input and the output beam, as well as the ray angles through the prism, and makes the necessary adjustments to the prism size and positioning. In a real system, the length of the prism along the optical axis is often significantly shorter than the glass equivalent plate, since the optical path in the prism is folded a few times. A good practice is to enter the real prism surfaces in the optical prescription when the design of the
150
Chapter 8 system is nearly finished and check the ray footprints on each prism surface as well as the optical performance of the whole system. It is also convenient to export a computer file with all the optical components in the system in a format that is suitable for the mechanical designer to design the mechanics around the optical components. When a ray is reflected from a flat mirror, the incident ray, the normal to the mirror at the point of incidence, and the reflected ray, all lie in a single plane, which is called the plane of incidence. Let us examine the orientation of the image after reflection from a flat mirror. If the observer looks directly at the object AB shown in Fig. 8.10, the point A appears to be the highest point of the object. If you look at the same object reflected from the mirror, it appears that the image is located behind the mirror in A′B′. However, this time it appears that point A′ is at the bottom of the image. One reflection changes the orientation of the image in the plane of incidence, which means in our example that the image is upside down. If the object is a two-dimensional object, there is no change in the image orientation in the plane perpendicular to the plane of incidence. In our example, this means that the left side of the object after reflection is seen as coming from the left side. Let us imagine that object AB has no symmetry. It could be, for example, letter the R. When viewed directly, the letter is oriented properly, and we can read it. After reflection in the mirror, the letter R is upside down, and even if we rotate it around the direction of image propagation, we can never orient it so that it will be readable. In the case when the image is readable, which is shown in Fig. 8.11a, we call it a “right-handed image.” If the image is as shown in Fig. 8.11b, where letter R is backwards, regardless of the orientation of the image, it is called a “left-handed image.” After multiple reflections off flat mirrors, or reflections inside a prism, a general rule says that an even number of reflections gives a right-handed image and an odd number of reflections gives a left-handed image. However, whether the number of reflections is even or odd does not tell us anything about the image orientation. Reflecting prisms are used to Erect the image in telescopes, which means that the top to bottom as well as the left to right are inverted, and the image is righthanded. Invert the image in one plane, either top to bottom or left to right. The image is left-handed. Deviate the optical axis, with inversion, erection, or no change in the image orientation.
Design Forms
151
Figure 8.10 Image Orientation after a Single Reflection from a Flat Mirror
Figure 8.11 Right- and Left-Handed Images
Displace the optical axis, with inversion, erection, or no change in the image orientation. Keep the unchanged image orientation, rotating the prism around the optical axis (these are prisms with no axis deviation or displacement) while the input image rotates around the center of the field of view (or around the input optical axis). As an example of an inverting prism, we will look at the Pechan prism. A Pechan prism is shown in Fig. 8.12. It consists of two prisms with a small air gap between them. There are a total of five reflections, which means that a right-handed image entering the prism is changed to a lefthanded image after the prism. All five reflections have a common plane
152
Chapter 8 of incidence, and the image is inverted in that plane. In the direction which is normal to the common plane of incidence, there is no change in the image orientation. Tracing of an image through a Pechan prism is shown in Fig. 8.12. The object chosen for tracing is a circle-arrow object. After refraction through the surface, AB, the image is totally internally reflected from surface BD. This TIR limits the field of view of the Pechan prism, which is about 10° for medium-index glasses. After surface BD, the rays reach the surface, AC, which has to be mirror coated. Small arrows on each surface show the orientation of the circle-arrow object as it falls on a given surface. The image is then refracted by the two surfaces with the air gap between them, and then totally internally reflected off surface EF. The next surface, GH, also has to be mirror coated for the rays to be reflected, and after the final TIR on surface EH, the image exits the prism as an inverted image with no deviation. Although the Pechan prism consists of two prisms, which means that the alignment and mounting of the prism is rather complicated, it is very commonly used to invert the image. Most of the systems that require image rotation or derotation, have a Pechan prism that rotates half the rotation angle of the scanning entrance mirror. It can be used in a convergent beam, and the clearance for the prism rotation is the smallest of all inverting prisms with no deviation.
Figure 8.12 Pechan Prism
Design Forms
153
Figure 8.13 Roof Pechan Prism
If surface GH of the Pechan prism is converted into a roof, where two sides of the roof are normal to each other, the prism is called a roof Pechan prism (Fig. 8.13). It has six reflections, so that the image is righthanded. The added reflection on the roof is in the plane which is normal to all other planes of reflection in the prism. This means that the image is right side up. Binoculars with a straight axis, which are Newtontype telescopes, use this type of prism for image erection. The prism is located between the objective and the image plane formed in the focus of the eyepiece. The light beam coming from one point in the field is split on the roof in two beam segments, each undergoing reflections on both sides of the roof. These two segments join after the roof, and form one image. However, if there is an error in the 90° roof angle, it may introduce the image blur or a double image. The tolerance on a roof angle is, in most cases, only a few arc-seconds. An optical designer has to be careful when designing the prisms, or using standard prisms in an optical system, because the prisms have to work properly for a specified field of view, or a given cone angle. Mistakes can result in the appearance of ghost images. For example, in the case of the Pechan prism, there are three surfaces where the beam is
154
Chapter 8 totally internally reflected. If the incident cone angle is too large for a chosen index of refraction of the prism, there will be one part of the field, which will not be properly reflected through the prism as the rest of the image. It will only be refracted and pass directly through the prism. The other case when the ghost images can appear is when the prism is not large enough and some skew rays undergo one extra reflection off the side surfaces. This can happen in the right-angle prism. The ghost reflections may be eliminated making the prism larger, and cutting notches in the prism. Let us now look at a right-angle telescope, determine what kind of prism can be used to deviate the optical axis by 90°, and also erect the image so that the viewer sees a noninverted right-handed image through the eyepiece. A Newtonian telescope creates an inverted right-handed image. If we put a screen in the focal plane of the objective, the image is both inverted and reverted. The objective creates an image which is right-handed, with an altered orientation both left to right and top to bottom. The eyepiece acts like a magnifier and it does not change the image orientation. In order to determine the image orientation at any location along the optical system, it is convenient to write on a small piece of paper an object with no symmetry. This can be a letter R, and this piece of paper should be moved through the space, simulating reflections off the prism mirror surfaces. You should always be located such that the image is moving toward your eyes. Do not forget to rotate the image left to right and top to bottom in the case of the objective lens or a relay lens, and do not rotate it through the eyepiece. Our problem is sketched in Fig. 8.14. The object is shown as a circle at the bottom, an arrow at the top, and a square on the left. After the objective, the image changes its orientation in both directions. Since the eyepiece does not change the image orientation, corrections in the image orientation in the horizontal and the vertical plane have to be done with the prism. If we would have only a plane mirror, the arrow and the circle would be properly oriented after the reflection. This is shown with the dotted lines drawn parallel to the optical axis. However, the square, which was turned to the right side after the objective, would stay on the right side after the reflection off the mirror. This means that we have to find a way to invert the image left to right, keeping only one reflection in the vertical plane. This can be accomplished using the right-angle prism and adding the roof on the hypotenuse surface. This prism is called the Amici prism, and it is shown in Fig. 8.15.
155
Design Forms
Figure 8.14 Right-Angle Telescope
There are many standard prism types. Useful information about prisms, their function, and the important dimensional relationships, can be found in the MIL-HDBK-141 (1962).
Design of Visual Systems Visual optics includes the wide variety of optical systems creating imagery to be viewed directly by the human eye. This includes telescopes, microscopes, binoculars, riflescopes, camera viewfinders, headmounted displays, magnifiers, and others. Common to all of these systems is that the eye is looking into some form of viewing optics such as an eyepiece.
Basic Parameters of the Human Eye The basic optical parameters of the human eye are listed in Table 8.1. Note that most of the data are listed as “approximately” due to the natural variation from person to person. The eye of an average young person can accommodate or focus to a distance in the order of 250 mm. Due to geometry, as a person looks at a progressively closer object, the two eyes must progressively increase their
156
Chapter 8
Figure 8.15 Amici Prism
angle of convergence. In the limit, for an interpupillary distance or IPD of 63.5 mm and an object at a 250-mm distance, the full convergence angle is 14.5°. If we work with a monocular system such as a riflescope, then convergence is not an issue; however, for a binocular, or even more for biocular systems, it can be quite important. A biocular system is a large field-of-view “eyepiece” about 100 mm in diameter, used for viewing a screen or display with both eyes. Figure 8.16 shows a binocular and a biocular system. The design of biocular systems is extremely difficult, and complex multielement designs often are required. One of the difficulties to the designer is that each eye is looking through the extreme edges of the biocular system, and this is the region of the pupil which generally is the most difficult to correct for aberrations. The user of a pair of binoculars will manually focus the binoculars. Since there is generally no convergence in the optical paths, the user will most often focus the binoculars at infinity, especially when looking at distant objects. This means that collimated light will exit the eyepiece and enter into the eye. If we were to design a riflescope, convergence is not an issue, so the user will focus the device to the most comfortable distance. This is often in the range of 2.5 to 6 m, although some research has shown that the resting state of the eye in a dark condition is more like 1 m. It is important to keep in mind that if you require the user to accommodate to some close distance, then you should consider converging the two optical paths (diverging them into the eyes).
157
Design Forms TABLE 8.1 Typical Human Eye Optical Parameters
Parameter
Value for Human Eye
Entrance pupil diameter (mm)
≈2.5 to ≈7
Focal length (mm)
≈16.9
ƒ/number
≈2.4 to ≈6.8
Distance from cornea to point of rotation (mm)
≈13.5
Radius of cornea (mm)
≈8
Interpupillary distance (IPD) (mm)
≈63.5 average, 46 to 80 range
Accurate seeing area (degrees)
≈1
Normal viewing angles (horizontal) (degrees)
≈±5 to ±30
Total visual limit (horizontal) (degrees)
≈±108
You can appreciate the situation if you consider providing diverging light into the two eyes from a virtual object 250 mm in front of the user. While the user can easily accommodate to a 250-mm distance, if the two optical paths were parallel to each other, then there would be potentially significant eye strain, since when accommodating to 250 mm, a person will naturally converge his or her eyes by about 14.5° as noted previously. There are a number of reasonably reliable eye models, and Figs. 8.17 and 8.18 show one of the more common models, the Lotmar eye model, for eye pupils of 7 and 3 mm in diameter, respectively. The data are shown for fields of view of 0, 22.5, and 45° off axis. You can see that there is a residual of spherical aberration which is, of course, more prominent with the larger pupil diameter. For the 7-mm-diameter pupil the spherical aberration equates to an rms blur diameter of about 8 min of arc on the retina, and this reduces to about 1.3 min of arc for the 3mm-diameter pupil. The eye was permitted to refocus for each pupil diameter. Note the significant off-axis coma and astigmatism residuals. It has been our experience that the residual eye aberrations are somewhat different for different eye models. This leads to the following question: Should the design of a visual system include the effects of the eye? In other words, should your optical design attempt to cancel the eye’s residual aberrations based on one of the eye models? In all likelihood you could do a reasonably good job of accomplishing this from a lens
158
Chapter 8
Figure 8.16 Biocular and Binocular Systems
Figure 8.17 Lotmar Eye Model with 7-mm-Diameter Pupil
design standpoint; however, the disadvantage is that the eye’s aberrations vary from person to person, and even the eye models available give somewhat different aberration residuals. It is generally accepted that it is most prudent to design visual optical systems assuming a perfect eye.
Pupil-Forming Systems Most (but not all) visual systems are known as “pupil-forming systems.” The term can be best illustrated by considering Fig. 8.19, where we show
Design Forms
159
Figure 8.18 Lotmar Eye Model with 3-mm-Diameter Pupil
a magnifying glass in Fig. 8.19a and a simple telescope in Fig. 8.19b. The magnifying glass is not a pupil-forming system. What this means is that there is no well-defined exit pupil from the magnifying glass which needs to be mated or matched to the entrance pupil of the eye. On the other hand, the exit pupil of the telescope (Fig. 8.19b) is well defined, and in order to see the imagery, the entrance pupil of the eye must be lined up with the exit pupil of the telescope. Another way to understand pupil-forming systems is to imagine placing a white card in place of the eye in both Figs. 8.19a and b. Further, assume a bright object which is being viewed. In the case of the magnifying glass, light from the object being viewed will fill a large area of diameter d1, which is effectively the diameter of the lens. In the case of the telescope, there will be a bright disk of diameter d2 at the exit pupil of the telescope. If the telescope were similar to a pair of 7 50 binoculars, this bright disk at d2 will be 7 mm in diameter. The important aspect of pupil-forming systems is that special attention must be given to assure that the light exiting the optical system does enter the pupil of the eye. There is a very interesting subtlety, and this can be understood by looking at Fig. 8.20. In Fig. 8.20a the eye is looking straight ahead to the left. The center of the field of view will be at or near the fovea, which is the highest acuity of the retina, and the user will see in his or her
160
Chapter 8
Figure 8.19 Pupil-Forming Optical Systems
peripheral vision the field stop of the eyepiece. In effect, the imagery will fall within a well-defined circle, and there is black outside of the circle. If the person now looks upward to the left by rotating his or her eye about the center of rotation of the eye, some of the light from the edge of the field will not enter the eye’s pupil. In situations where we have a wide apparent field-of-view telescope with a 7-mm or smaller exit pupil diameter, when the person looks upward toward the edge of the field stop, the light may even disappear completely! It is possible to move your eye closer to the eyepiece so that the exit pupil of the telescope is located at the point of rotation of the eye. Now the person can see clearly the field stop in the eyepiece when looking toward the field stop; however, when looking straight ahead, the field stop and the outer periphery of the field of view may completely disappear from view! This is a very striking, as well as a weird, effect, and if you ever have the opportunity to see it, it is worthwhile to do so.
Requirements for Visual Optical Systems When designing visual systems, a number of parameters must be considered which are unique to these systems, and these are listed here:
Design Forms
161
Figure 8.20 Telescope Showing Effect of Eye Rotation
For many hand-held systems such as binoculars, the user will most often bring the object of greatest interest to the center of the field of view. For this reason, off-axis performance is generally more forgiving for these systems. The eye relief is the clearance or distance from the last optical element in the viewing optics to the front of the cornea of the eye. For eyeglass users the generally accepted minimum eye relief is in the order of 25 mm. Larger values are, of course, helpful, but the diameter of the eyepiece grows with the eye relief. It is clear from the transverse ray aberration curves for the Lotmar eye model that the resolution of the eye degrades quite severely as we move away from the center of the field of view. The visual acuity of the eye is maximum at the fovea, which is very close to the center of the field of view of the eye. As an object moves away from the fovea, the visual acuity decreases dramatically, and at ±20° the visual acuity is only about 10% of that at the fovea. This is well illustrated in Fig. 18.21 where we show a series of letters of different sizes. The increase in letter size is inversely proportional to the decrease in visual acuity as we move from the fovea. Thus, if you look at the small spot at the center of the figure, all of the letters should be approximately equally resolved.
162
Chapter 8 Although it is true that the visual acuity drops quickly away from the fovea, visual systems should have relatively good imagery at the edge of the field. How good depends on the application of the system. For example, consider a binocular. A viewer can rotate his or her eyes to look toward the edge of the field, in which case the field periphery is the sharpest area the eye sees. This could lead us to a conclusion that the edge of the field should be very well corrected for aberrations. However, we all know that any object in the field can be brought to the center by simply rotating the whole binocular. So the quality of the imagery at the edge of the field in a binocular does not have to be as good as in the center, but it should not be so bad that the image blurring and coloring is immediately noticed when the eyes are pointed to the field edge.
Figure 8.21 Illustration of Visual Acuity As a Function of Distance from the Fovea
Design Forms
163 The most general and accepted metric that we often hear is that the eye resolves 1 min of arc. What this means is that the eye can resolve the capital letter E when each of the dark or bright bars forming the horizontal portions of the letter subtend 1 min of arc, as shown in Fig. 8.22. This means that the eye resolves 2 min per line pair, or 0.5 line pair per minute of arc. With respect to visual systems design, providing an image blur diameter from 1 min of arc to perhaps 3 min of arc is generally considered an acceptable level of performance in the center of the field of view. At the edge of the field, 20 to 40 arc min of image blur maximum may be acceptable. Table 8.2 shows a list of the typical tolerances associated with optics for the eye, as developed by Mouroulis. These data are for binocular viewing with two eyes. Note that items that the eye normally does not do are specified with tighter tolerances. This includes dipvergence (one eye looking upward and the other eye downward) and divergence for example. There is a rule of thumb that says that the eye can resolve a contrast of 5%. Thus, it is not uncommon to determine where the MTF drops to 0.05 and to conclude that the eye will resolve this spatial frequency. There is perhaps a better way, and this is to use the so-called aerial image modulation (AIM) curve. This is the relationship between the contrast and the number of line pairs per millimeter that the eye can resolve. Walker shows these data, and they are summarized in Fig. 18.23. The AIM curve is a relationship between the modulation required to resolve
Figure 8.22 Eye Resolution
164 TABLE 8.2 Typical Tolerances for Visual Systems
Chapter 8 Parameter
Typical Specification
Divergence (degrees)
0
Convergence (degrees)
1.5
Dipvergence (min)
8
Magnification difference (%)
±0.5 to ±1
Brightness difference (%)
±10
Best focus if fixed
1 diopter*
Accommodation
3 diopter to infinity is OK 1 to 1.5 diopter is best
Axial chromatic aberration
1 to 1.5 diopters
Lateral color (min)
2
Image quality
Integral of MTF from 0 to 20 line pairs/degree
*A diopter is the reciprocal focal length, in meters. As used in the table, 1 diopter means that the eye will be focusing to a distance of 1 m in front of the user.
a given target and the spatial frequency of the target. Using the Lotmar eye model with a 7-mm pupil diameter, we see that if the eye were diffraction limited in Fig. 8.23a, we would resolve 1.6 min/line pair, or 0.8 min/line; however, due to the spherical aberration, we can only resolve in the order of 3 min/line pair, or 1.5 min/line (Fig. 8.23b). In the case of a 3-mm pupil diameter the diffraction-limited eye would resolve about 1.6 mm/line pair (Fig. 8.23c) and the Lotmar model predicts about 1.7 mm/line pair (Fig. 8.23d). It is important to realize that these data are only as accurate as the Lotmar eye model and the referenced AIM threshold data. While they may not be precisely accurate, they do give us a good indication of the resolution of the eye. Distortion is an important criterion in visual systems. As we learned in Chap. 5, distortion is more of a mapping error rather than an imagedegrading aberration. Its primary effect is to the cosmetic appearance of the image. Distortion is a change in magnification with field of view. Generally, positive or negative distortion in the order of 2 to 2.5% is small enough to be almost imperceptible. Large amounts of distortion can be annoying in any visual system. Telescopes with a large apparent field of view often have up to 10% of distortion at the edge of the field.
165
Design Forms
Figure 8.23 Use of AIM Threshold Curve to Predict Visual Resolution
Summary on Design of Visual Systems It is best in the design of visual optical systems to assume a perfect eye model. Most of the computer design programs have the ability to model a so-called perfect lens or paraxial lens, which is used following the system being designed to emulate the eye (or any form of focusing lens). What these so-called perfect lenses do is to simply compute the angular aberrations in the optical system and multiply them by the focal length of the perfect lens which is input by the user. So if you are interested in the actual image blur on the retina, then use a perfect lens of focal length 16.9 mm, which is the approximate focal length of the eye. If you are designing a visual system which must be fixed focus, it is probably best to design and produce your system to provide light which is either collimated to the user or appears to come from a distance of from 3 to 6 m. Some data suggest a value closer to 1 m. If you can allow the user to refocus, this is generally preferred. The image quality, or blur diameter, should be in the order of 1 min of arc to 3 min of arc. The specific application will have a lot to do with how good the imagery needs to be. You should design your system for an exit pupil diameter of at least 7 mm (10 to 12 mm is better), and then evaluate the performance both at the 7-mm-diameter pupil as well as
166
Chapter 8 with reduced pupil diameters. Some detailed specifications include the eye being decentered to various positions within the exit pupil of the optical system. If the system is to be used in bright conditions, you may even evaluate your design in the 2.5- to 3-mm pupil diameter region. Our final note on the design of visual systems is to keep in mind that the eye is quite forgiving. Persons who get a new eyeglass prescription often notice color fringing or lateral color when looking toward the outer periphery of their field of regard (30 to 40° from straight ahead, for example). After several days to several weeks, this color fringing often seems to disappear. The eye, along with the rest of the human visual system, is, in effect, a very powerful computer with impressive image-processing capabilities. This does not mean that you can ignore the aberrations and image quality of visual systems, what it does mean, however, is that, in many situations, the optics for visual systems can be more forgiving than you might think.
CHAPTER
9
The Optical Design Process
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
168
Chapter 9 The optical design process includes a myriad of tasks that the designer must perform and consider in the process of optimizing the performance of an imaging optical system. While we often think primarily of the robustness of the optimization algorithm, reduction of aberrations, and the like, there is much more to do. The designer must be at what we sometimes call “mental and technical equilibrium with the task at hand.” This means that he or she needs to be fully confident that all of the following are understood and under control: All first-order parameters and specifications such as magnification, focal length, ƒ/number, full field of view, spectral band and relative weightings, and others. Assure that the optical performance is being met, including image quality, distortion, vignetting, and others. Assure that the packaging and other physical requirements, including the thermal environment, is being taken into account. Assure that the design is manufacturable at a reasonable cost based on a fabrication, assembly, and alignment tolerance analysis and performance error budget. Consider all possible problems such as polarization effects, including birefringence, coating feasibility, ghost images and stray light, and any other possible problems. Once every one of these items has been addressed and is at least recognized and understood, we start with the sketch of the system. First, the system is divided into subsystems if possible, and the firstorder parameters are determined for each subsystem. For example, if we are to design a telescope with a given magnification, the entrance pupil diameter should be chosen such that the exit pupil size matches the eye pupil. A focal length of the objective and the eyepiece should be chosen such that the eyepiece can have a sufficiently large eye relief. Now, when the specs for each subsystem are defined, it is time to use the computer-aided design algorithms and associated software to optimize the system, which will be discussed in the rest of this chapter. Each subsystem can be designed and optimized individually, and the modules joined together or, more often, some subsystems are optimized separately and some as an integral part of the whole system.
The Optical Design Process
169
What Do We Do When We Optimize a Lens System? Present-day computer hardware and software have significantly changed the process of lens design. A simple lens with several elements has nearly an infinite number of possible solutions. Each surface can take on an infinite number of specific radii, ranging from steeply curved concave, through flat, and on to steeply curved convex. There are a near infinite number of possible design permutations for even the simplest lenses. How does one optimize the performance with so many possible permutations? Computers have made what was once a tedious and timeconsuming task at least manageable. The essence of most lens design computer programs is as follows: First, the designer has to enter in the program the starting optical system. Then, each variable is changed a small amount, called an increment, and the effect to performance is then computed. For example, the first thickness may be changed by 0.05 mm as its increment. Once this increment in thickness is made, the overall performance, including image quality as well as physical constraints, are computed. The results are stored, and the second thickness is now changed by 0.05 mm and so on for all variables that the user has designated. Variables include radii, airspaces, element thicknesses, glass refractive index, and Abbe number. If you are using aspheric or diffractive surfaces, then the appropriate coefficients are also variables. The measure of performance as used here is a quantitative characterization of the optical performance combined with a measure of how well the system meets its first-order constraints set by the user such as focal length, packaging constraints, center and edge thickness violations, and others. The result of the computation is a single number called an error function or merit function. The lower the number, the better the performance. One typical error function criteria is the rms blur radius, which, in effect, is the radius of a circle containing 68% of the energy. Other criteria include optical path difference, and even MTF, as described in Chap. 15. The result is a series of derivatives relating the change in performance (P ) versus the change in the first variable (V1), the
170
Chapter 9 change in performance (P) versus the change in the second variable (V2), and so on. This takes on the following form: ∂P ∂P ∂P ∂P , , , … ∂V1 ∂V2 ∂V3 ∂V4 This set of partial derivatives tells in which direction each parameter has to change to reduce the value of the sum of the squares of the performance residuals. This process of simultaneous parameter changes is repeated until an optimum solution is reached. A lens system consists of a nearly infinite number of possible solutions in a highly multidimensional space, and it is the job of the designer to determine the optimum solution. Designers have used the following analogy to describe just how a lens design program works: Assume that you cannot see and you are placed in a threedimensional terrain with randomly changing hills and valleys. Your goal is to locate the lowest elevation or altitude, which in our analogy equates to the lowest error function or merit function. The lower the error function, the better the image quality, with the “goodness” of performance being inversely proportional to the elevation. You are given a stick about 2 m long, and you first stand in place and turn around tapping the stick on the ground trying to find which direction to walk so as to go down in elevation. Once you determine the azimuth resulting in the greatest drop in elevation, you step forward in that direction by 2 m. You now repeat this process until in every direction the elevation goes up or is level, in which case you have located the lowest elevation. But what if just over a nearby hill is an even lower valley than you are now in? How can you find this region of solution? You could use a longer stick, or you could step forward a distance several times as long as the length of your stick. If you knew that the derivative or slope downward is linear or at least will continue to proceed downward, this may be a viable approach. This is clearly a nontrivial mathematical problem for which many complex and
The Optical Design Process
171
innovative algorithms have been derived over the years. But the problem is so nontrivial as well as nonlinear that software algorithms to locate the so-called global minimum in the error function are still elusive. Needless to say, the true global minimum in the error function may be quite different or distant from the current location in our n-dimensional terrain. Figure 9.1 shows a two-dimensional representation of solution space as discussed previously. The ordinate is the error function or merit function, which is a measure of image quality, and the abscissa is, in effect, solution space. We may initiate a design on the left and the initial optimization brings the error function to the first minimum called a local minimum in the error function. We then change glasses and/or make other changes to the design and ultimately are able to move the design to the next lower local minimum. Finally, we add additional elements and make other changes and we may be able to reach the local minimum on the right. But how do we know that we are at, or even close to, a global minimum? Here lies the challenge as well as the excitement of lens design! It is important here to note that reaching global minimum in the error function is not necessarily the end goal for a design. Factors including tolerance sensitivity, packaging, viability of materials, number of elements, and many other factors influence the overall assessment or “goodness” of a design. Learning how to optimize a lens system is, of
Figure 9.1 Illustration of Solution Space in Lens Design
172
Chapter 9 course, quite critical to the overall effort, and learning how to reach a viable local or near-global minimum in the error function is very important to the overall success of a project.
How Does the Designer Approach the Optical Design Task? The following are the basic steps generally followed by an experienced optical designer in performing a given design task. Needless to say, due to the inherent complexity of optical design, the processes often becomes far more involved and time consuming. Figure 9.2 outlines these basic steps: 1. The first step in the design process is to acquire and review all of the specifications. This includes all optical specifications including focal
Figure 9.2 Lens Design and Optimization Procedure
The Optical Design Process
173
length, ƒ/number, full field of view, packaging constraints, performance goal, environmental requirements, and others. 2. Then we select a representative viable starting point. The starting point should, wherever possible, be a configuration which is inherently capable of meeting the specifications for the design. For example, if the specifications are for an ƒ/10 monochromatic lens covering a very small field of view and having an entrance pupil diameter of 5 mm, then the lens may very well be a single element. However, if the requirements call for an ƒ/1.2 lens over a wide spectral band covering a 40° full field of view, then the solution may very well be a very complex six- to seven-element double Gauss lens form. If we were to use a single element for this latter starting point, there would be no hope for a viable solution. Finding a good starting point is very important in obtaining a viable solution. The following are viable sources for starting points: You can use a patent as a starting point. There are many sources for lens patents including Warren Smith’s excellent book Modern Lens Design. There is also a CD-ROM called “LensView,” which contains over 20,000 designs from patents. These are all searchable by a host of key parameters. While the authors of this book are not patent attorneys, we can say with confidence that you may legally enter design data from a patent into your computer and work with it in any way that you would like to. If your resulting design is sold on the market, and if the design infringes on the patent you used (or any other for that matter), you could be cited for patent infringement. It is interesting to note that the purpose of our patent system in this country is to promote inventions and innovation. This is done by offering an inventor a 17-year exclusive right to his or her invention in exchange for teaching in the patent how to implement the invention. Thus, you are, in effect, invited to use the design data and work with it with the goal of coming up with a better design, which you can then go out and patent. By this philosophy, inventors are constantly challenged to improve upon an invention, which, in effect, advances technology, which is what the patent process is all about. Needless to say, we urge you to be careful in your use of patents. You could use a so-called hybrid design. We mean a hybrid to be the combining of two or more otherwise viable design approaches so as to yield a new system configuration. For example, a moderate field-of-view Tessar lens design form can be combined with one or more strongly negatively powered elements in the front to create an extremely
174
Chapter 9 wide-angle lens. In effect, the Tessar is now used over a field of view similar to its designed field, and the negative element or elements bend or “horse” the rays around to cover the wider field of view. An original design can, of course, be a viable starting point. As your experience continues to mature, you will eventually become comfortable with “starting from scratch.” With today’s computer-aided design software, this works most of the time with simple systems such as doublets and triplets; however, with more complex systems, you may have problems and will likely be better off resorting to a patent or other source for a starting point. 3. Once you have entered your starting point into the software package you are using, it is time to establish the variables and constraints. The system variables include the following: radii, thicknesses, airspaces, surface tilts and decenters, glass characteristics (refractive index and Abbe number), and aspheric and/or other surface variables, including aspheric coefficients. The constraints include items such as focal length, ƒ/number, packaging-related parameters (length, diameter, etc.), specific airspaces, specific ray angles, and virtually any other system requirement. Wavelength and field weights are also required to be input. It is important to note that it is not imperative (nor is it advisable) to vary every conceivable variable in a lens, especially early in the design phase. For example, your initial design optimization should probably be done using the glasses from the starting point, in other words do not vary glass characteristics initially. This will come later once the design begins to take shape and becomes viable. You may also want to restrict the radii or thicknesses you vary as well, at least initially. For example, if adjacent elements have a very small airspace in the starting design, this may be for a good reason, and you should probably leave them fixed. Also, element thicknesses are very often not of great value as variables, at least initially, in a design task, so it is usually best to keep element thicknesses set to values which will be viable for the manufacturer. 4. You now will set the performance error function and enter the constraints. Most programs allow the user to define a fully “canned” or automatically generated error function, which, as discussed earlier, may be the rms blur radius weighted over the input wavelengths and the fields of view. In the Zemax program the user selects the number of rings and arms for which rays will be traced into the entrance pupil (rays are traced at the respective intersection points of the designated number of rings and arms). Chapter 21 shows a detailed example of how we work with the error function.
The Optical Design Process
175
5. It is now time to initiate the optimization. The optimization will run anywhere from a few seconds for simple systems to many hours, depending on just how complex your system is and how many rays, fields of view, wavelengths, and other criteria are in the system. Today, a state-ofthe-art PC optimizing a six- to seven-element double Gauss lens with five fields of view will take in the order of 5 to 10 s per optimization cycle. Once the computer has done as much as it can and reaches a local minimum in the error function, it stops and you are automatically exited from the optimization routine. 6. You now evaluate the performance using whatever criteria were specified for the lens. This may include MTF, encircled energy, rms spot radius, distortion, and others. 7. You now repeat steps 3 and 5 until the desired performance is met. Step 3 was to establish the variables and constraints, and step 5 was to run the optimization, and these steps are repeated as many times as necessary to meet the performance goals. You will often reach a solution that simply does not meet your performance requirements. This is very common during the design evolution, so do not be surprised, depressed, or embarrassed if it happens to you…it happens to the best of us. When it does happen, you may need to add or split the optical power of one or more of the lens elements and/or to modify glass characteristics. As we have discussed previously, splitting optical power is extremely valuable in minimizing the aberrations of a lens. 8. There is a really simple way of splitting an element in two, and while it is not “technically robust,” it does work most of the time. What you do is insert two surfaces in the middle of the current element, the first of which will be air and the second is the material of your initial element. The thickness of each “new” element is one-half of the initial element and the airspace should be small, like 0.1, for example. Now simply enter twice the radius of the original element for both s1 and s 2 of the new elements. You will end up with two elements whose net power sum is nearly the same as your initial element. You can now proceed and vary their radii, the airspace, and, as required, the thicknesses. 9. If you still cannot reach a viable design, then at this point you will need to return to step 2 and select a new starting point. 10. Your final task in the design process is to perform a tolerance analysis and performance error budget. We will be discussing tolerancing in more depth in Chap. 16. In reality, you should be monitoring your tolerance
176
Chapter 9 sensitivities throughout the design process so that if the tolerances appear too tight, you can take action early in the design phase and perhaps select a less sensitive design form. 11. Finally, you will need to generate optical element prints, contact a viable lens manufacturer, and have your elements produced. You will also need to work with a qualified mechanical designer who will design the cell or housing as well as any required interfaces. It is important to note that while we list the mechanical design as taking place at this point after the lens design is complete, it is extremely important to work with your mechanical designer throughout the lens design process so as to reach an optimum for both the optics as well as the mechanics. Similarly, you should establish a dialog with the optical shop prior to completing the design so as to have time to modify parameters which the shop feels needs attention such as element thicknesses, glass types, and other parameters. 12. Once the components are in house, you will need to have the lens assembled and tested. Assembly should be done to a level of precision and cleanliness commensurate with the overall performance goals. Similarly, testing should be to a criterion which matches or can be correlated with your system specifications and requirements. We discuss testing in Chap. 15.
Sample Lens Design Problem There was a very interesting sample lens design problem presented at the 1980 International Lens Design Conference. The optimized design for an ƒ/2.0, 100-mm focal length, 30° full field-of-view double Gauss lens similar to a 35-mm camera lens was sent out to the lens design community. One of the tasks was to redesign the lens to be ƒ/5 covering a 55° full field with 50% vignetting permitted. Figure 9.3 shows the original starting design, as well as the design after changing the ƒ/number and field of view, without any optimization. Sixteen designers submitted their results, and they spent from 2 to 80 h working on the problem. We will present here three representative solutions in Fig. 9.4. The design in Fig. 9.4a is what we often call a happy lens. What we mean is that the lens is quite well behaved with no steep bending or severe angles of incidence. The rays seem to “meander” nicely
The Optical Design Process
177
Figure 9.3 Starting Design for Sample Lens Design Problem
through the lens. It is a comfortable design. We show to the right of the layout a plot of the MTF. MTF will be discussed in detail in Chap. 10. For the purpose of this discussion, consider the MTF to be contrast plotted in the ordinate as a function of the number of line pairs per millimeter in the abscissa. The different curves represent different positions in the field of view and different orientations of the resolution patterns. The higher the curves, the better the contrast and the overall performance. The MTF is reasonable for most of the field positions. As will be discussed in Chap. 21, a good rule of thumb for the MTF of a 35-mm camera lens is an MTF of 0.3 at 50 line pairs/mm and 0.5 at 30 line pairs/mm. The design in Fig. 9.4b has a serious problem; the rays entering the last element are at near-grazing angles of incidence. Notice that the exit pupil at full field is to the right of the lens (since the ray cone is descending toward the axis to the right), and at 70% of the field the exit pupil is to the left of the lens (since the ray cone is ascending to the right and therefore appears to have crossed the axis to the left of the lens). This is a direct result of the steep angles of incidence of rays entering the last element. The variation in exit pupil location described here would not itself be an issue unless this lens were used in conjunction with another optical system following it to the right; however, it does indicate clearly the presence of the severe ray bending which will inevitably lead to tight manufacturing and assembly tolerances. Further, the last element has a near-zero edge thickness which would need to be increased. The lens is large, bulky, and heavy. And finally, the MTF of this design is the lowest of the three designs presented.
178
Chapter 9
Figure 9.4 Representative Solutions to Sample Lens Design Problem
Finally, the design in Fig. 9.4c is somewhat of a compromise of the two prior designs in that it is somewhat spread out from the design in Fig. 9.4a but does not have the problems of the design in Fig. 9.4b. The MTF of the design in Fig. 9.4c is the best of the three designs. Comparing the three designs is very instructive as it shows the extreme variability of results to the same problem by three designers.
The Optical Design Process
179
The question to ask yourself is what would you do if you subcontracted the design for such a lens, and after a week or two the designer brought you a stack of paper 200-mm thick with the results of the design in Fig. 9.4b. And what if he or she said “wow, what a difficult design! But I have this fabulous solution for you!” Prior to reading this book, you might have been inclined to congratulate the designer on a job well done, only to have problems later on during manufacturing and assembly. Now, however, you know that there may be alternate solutions offering superior performance with looser tolerances and improved packaging. Remember that even a simple lens has a near infinite number of possible solutions in a multidimensional space.
This page intentionally left blank
CHAPTER
10 Computer Performance Evaluation
Copyright © 2000 by The McGraw-Hill Companies, Inc. Click here for terms of use.
182
Chapter 10
What Is Meant by Performance Evaluation The performance characteristics of an imaging optical system can be represented in many ways. Often the final optical performance specification is in terms of the modulation transfer function (MTF), encircled energy, rms blur diameter, or other image quality criteria. These criteria relate in different ways to the image quality of the system. Image quality can be thought of as resolution or how close two objects can approach each other while still being resolved or distinguished from one another. Image quality can also be thought of as image sharpness, crispness, or contrast. As discussed earlier, imagery is never perfect. It is limited by geometrical aberrations, diffraction, the effects of manufacturing and assembly errors, and other factors. The characterization of image quality by the methods described in the following sections will help you to assess just how your system performs with respect to its imagery. It is important to realize that the image quality or resolution of the entire system is not totally dependent on the optics, but may include the sensor, electronics, display device, and/or other system components making up the system. For example, if the eye is the sensor, it can accommodate for both defocus and field curvature, whereas a flat sensor such as a CCD cannot. In this chapter, we will be discussing only the optics contribution to image quality.
What Is Resolution? When we think about the image quality of an image-forming optical system such as a camera lens, the first parameter that often comes to mind is resolution or resolving power. Classically, the ability of an optical system to separate two closely spaced point sources at the nominal object distance is generally considered to be the resolution. Consider a perfect optical system which has an entrance pupil diameter, D, and focuses to an image with a given ƒ/#. Two point sources closely spaced will be imaged through the optical system, each of them forming a diffraction pattern. If two perfect diffraction patterns as in Fig. 10.1 are separated by the radius of the Airy disk (the radius of the
183
Computer Performance Evaluation
Figure 10.1 Two Resolvable Images of Closely Spaced Point Sources
first dark ring in the diffraction pattern), then the intensity midway between the two peaks in the pattern drops to 0.74 of the maximum intensity, and the two point images are said to be resolvable. This is the Rayleigh criterion for resolution. This, of course, assumes that the ultimate media or sensor is not the limiting factor. The separation, d, of the two points in the image plane is d 1.22 ƒ/# in units of wavelength. In object space, in radians, this becomes ( and pupil diameter in ssme units) 1.22 entrance pupil diameter or very frequently used as a rule of thumb, the resolution, in arc seconds, for the visible spectral range is 136 entrance pupil diameter where the entrance pupil diameter is given in millimeters. This is interesting and certainly of value in understanding the limiting resolution of the optical system with given first-order optical parameters, but it really does not help us to understand the performance of a specific optical system design. As will be shown in this chapter, there is far more to the characterization of optical performance than the theoretical resolution.
184
Chapter 10
Ray Trace Curves Most of the methods used in computing image quality, such as the modulation transfer function, spot diagrams, encircled energy, and the like, are functionally robust and represent different, yet similar representations of the net performance of the optical system as designed. However, there are two disadvantages with these metrics. First, they can sometimes take too much time to compute. This, however, is less and less of a problem as PCs have become faster and faster. Second, the real problem is that while these metrics do help to show the overall net resulting image quality, they do not provide a detailed indication to the designer of the specific aberrations present in the design over the field of view and over the spectral bandwidth. While some information can at times be derived, more often the user really cannot tell what aberrations are present and at what magnitudes. These data are important to the designer as an aid in correcting the residual aberrations. The solution is to generate what are called transverse ray aberration curves or simply ray trace curves. With these graphical data, a reasonably experienced designer can immediately tell just how much spherical aberration, coma, astigmatism, field curvature, axial color, lateral color, and field curvature are present. In addition, in many cases the user can also tell what orders of these aberrations are present. Finally, with this knowledge, the designer can often make a reliable judgment as to what to do next regarding further optimization of the lens. In spite of some fabulous advances in performance simulation and modeling, transverse ray aberration curves are still invaluable to the serious designer. We show in Fig. 10.2 the basic formation of the ray trace curve. This perspective figure (Fig. 10.2) shows a lens exit pupil with the lens imaging to an off-axis image position. First, consider tracing the chief ray to the image. The height on the image of the chief ray is our reference point, and is generally taken to be the image height. Now let us trace a ray through the top of the exit pupil. This ray, which is called the upper marginal ray, hits the image higher than the chief ray for the aberration shown, which is coma. Now let us trace a ray through the bottom of the exit pupil. This ray, which is called the lower marginal ray, also hits the image higher than the chief ray, and in fact for classical third-order coma it hits the image the same distance above the chief ray as the ray from the top of the pupil. In other words, both of the rays from the top and the bottom of the exit pupil hit the image vertically displaced by the same amount.
Computer Performance Evaluation
185
Figure 10.2 Explanation of Ray Trace Curves
We will now proceed to establish a set of coordinate axes for our ray trace curves. In the first set of coordinates (on the left in Fig. 10.2), the abscissa is the normalized exit pupil radius in the y direction, and the ordinate is the distance above or below the chief ray on the image that our ray intersects the image plane (y). Thus, both the upper and lower marginal rays form the end points on the curve. We now proceed to trace rays through each of the black dots from y 1 to y 1, with the intersection points relative to the chief ray plotted on the curve. For third-order coma the result will be a quadratic or parabolic curve since third-order coma is quadratic with aperture. Now we establish a second set of coordinate axes, as shown on the right in Fig. 10.2. Here we have the normalized X coordinate in the exit pupil in the abscissa, and the displacement of the ray in the x direction (x) as the ordinate. As it turns out, for third-order coma there is no x departure at all for these rays in the exit pupil. We will show why this is the case shortly. For now, you will see that for thirdorder coma a quadratic curve in the “tangential” ray fan and zero departure for the x rays in the “sagittal’ ray fan are the results. If any lens designer who is “worth his or her salt” sees this form of ray aberration curves with a quadratic in the tangential ray fan and virtually zero in the sagittal curve, then he or she should conclude instantly that the lens has third-order coma.
186
Chapter 10 Since these ray trace curves are so fundamentally important to the optical designer’s work, a more in-depth discussion is in order. As you will see, there are here, as with many other areas of optical design, subtleties that could easily be misleading if not fully understood. Consider our coma pattern where the ray trace curves suggest zero x departure of the rays hitting the image, which implies or suggests zero x width to the image blur. Yet we all know that coma does have width in the x direction. Just what is going on, and why are the data misleading? Figure 10.3 will explain the situation. Here we trace rays around the periphery of the exit pupil from positions 1 through 8. From our prior discussion, we know that the chief ray is our reference, and that rays 1 and 5 from the top and bottom of the exit pupil both hit the image high, above the chief ray. If you follow the numbers in Fig. 10.3, you will see how one rotation around the exit pupil results in two rotations around an ellipse in the image, and since positions 1 and 5 are both high, then positions 3 and 7 which are 180° opposed will be at the bottom of the elliptical pattern. Neither of these rays will have any x departure at all! Thus, the ray trace curve for rays traced in the x direction was
Figure 10.3 Formation of Comatic Image Blur
Computer Performance Evaluation
187
a horizontal line in Fig. 10.2. So where is the x spreading of the coma pattern coming from? The answer is from rays at positions 2, 4, 6, and 8, which are called skew rays. Since the rays making up the ray trace curves contain only the y (or tangential rays) and the x (or sagittal rays), the designer sees no indication or evidence whatsoever of the x spreading of the imagery. This is a real subtlety, and it is a fine example why one should never be totally dependent on only one form of image evaluation or analysis. By looking only at the ray trace curves, one could easily conclude that such a system had virtually zero x spreading of the offaxis imagery, and this could make its performance ideal for some system applications. For the most part use of the ray trace curves are wonderfully helpful and revealing; however, do be aware of subtleties as pointed out earlier. A further illustration of the ray trace curves, Fig. 10.4 shows how spherical aberration is formed and how the ray trace curves are derived. In the top of Fig. 10.4 the image is located at paraxial focus and it should be clear how each of the rays entering the lens from the left results in a corresponding intercept on the image plane and how this is plotted as the ray trace curve. Ray 1 strikes the image lowest and results
Figure 10.4 Formation of Ray Trace Curves for Spherical Aberration
188
Chapter 10 in point a in the plot. Ray 2 is the next ray lower down entering the entrance pupil and it results in point b in the plot, and so on. Since third-order spherical aberration is cubic with aperture, the resulting curve is cubic. Note the symmetry above and below the optical axis. Now consider what happens if we relocate the image plane to the “best focus” position. Following the same logic in generating the ray trace curves, we see a much lower departure of the ray intercept points making up the curve. This is true and quite real, and it tells us that the image blur diameter when we refocus the image will be significantly reduced from that at paraxial focus. As an exercise, what will the ray trace curve be for a perfect image where the image plane is intentionally defocused toward the lens? The answer is a straight line sloped upward to the right. So let’s use this as an aid in further understanding ray trace curves. Since defocus yields a sloped but otherwise straight line, we can easily determine what any ray trace curves for any lens will look like as we go through focus by simply drawing or imagining a sloped straight line as a new coordinate axis. This is an invaluable tool as you can now immediately assess the relative improvement after refocusing a given lens. And since field curvature is a quadratic change in focus with field of view, you can with a little practice assess immediately the benefits of curving your sensor if this is possible. We show in Fig. 10.5 ray trace curves for various typical aberrations and combinations of aberrations: Figure 10.5a is pure defocus. As noted earlier, defocus will produce equal sloped straight lines in the sagittal and tangential ray fans. Recall that the tangential ray fan is in the y-z direction and typically oriented parallel to the field-of-view direction. The sagittal ray fan is orthogonal to the tangential ray fan, and typically, the sagittal fan is fully symmetrical which is why we sometimes show only one-half of the fan. Figure 10.5b shows straight lines at different slopes. This is a combination of astigmatism (which is the difference between the slopes of the two curves) and defocus. Figure 10.5c shows that if we best focus for the residual astigmatism off axis as we might do with a curved image surface, we find the result here where an equal and opposite ray fan slope results in the tangential and sagittal directions. Figure 10.5d is negative or undercorrected third-order spherical aberration, which is, of course, a cubic with aperture.
Computer Performance Evaluation
189
Figure 10.5 Typical Transverse Ray Aberration Curves
The data in Fig. 10.5e are the same third-order spherical aberration as in Fig. 10.5d, only we have refocused the image to a more optimum focus position to minimize the residual blur diameter. Figure 10.5f shows negative third-order spherical aberration, which is being balanced by positive fifth-order spherical aberration. The data in Fig 10.5g are for pure third-order coma, which, as we know from before, is quadratic with aperture. We also know from before that the sagittal curve indicates zero image blurring in the sagittal direction. This may be misleading and is due to the nature of coma formation and the fact that the ray aberration curves show only the rays along two lines in the pupil plane. The data in Fig. 10.5h are for a combination of third-order coma and astigmatism. Figure 10.5i shows a combination of some negative third-order spherical aberration at the central wavelength as well as secondary axial color
190
Chapter 10 and spherochromatism. The secondary axial color is the focus difference between the central wavelength and the common red and blue focus, which together are focused beyond the central wavelength. The spherochromatism is the change in spherical aberration with wavelength. Finally, Fig. 10.5j shows an off-axis ray trace curve with primary lateral color or color fringing along with a small amount of coma and astigmatism. It should be quite apparent that the ray trace curves for each of the aberrations has its own distinctive form, and this is what makes them so useful. The aberrations, in effect, add algebraically, so it is easy to tell almost immediately what aberrations are present in a given design at the different field positions.
Spot Diagrams Spot diagrams are the geometrical image blur formed by the lens when imaging a point object. This is a more functionally useful form of output; however, it is sometimes difficult to distinguish the specific aberrations present. Figure 10.6 shows the spot diagrams for a Cooke triplet form of lens and shows both the transverse ray aberration curves as well as spot diagrams for the same field positions. Generally, the rms spot radius or diameter is output with the spot diagrams. The rms spot diameter is the diameter of a circle containing approximately 68% of the energy. This metric can be of great value, especially when working with pixelated sensors where one often wants the image of a point object to fall within a pixel. Note that in optical design software we often come across the terms “spot radius,” “spot diameter,” and “spot size.” While the designer is most interested in spot diameter, the software generally outputs spot radius. The use of the words “spot size” is fine for relative comparison (for example, “the spot size has increased by a factor of 2”); however, the term can cause undo confusion when tied to a specific value. For example, “the spot size is 50 m” does not really tell us whether this is the radius or diameter of the image blur, nor does it tell us whether this is for 100% of the energy or some other value such as the rms. Be careful in interpreting these forms of data from the software you are using.
Computer Performance Evaluation
191
Figure 10.6 Geometrical-Based Spot Diagrams and Transverse Ray Aberration Curves for Cooke Triplet Example
Optical Path Difference As we know from Chap. 4, if the peak-to-valley optical path difference (P-V OPD) is less than or equal to one-fourth of the wavelength of light, the image quality will be almost indistinguishable from perfect. It is known as diffraction limited. Just like transverse ray aberration curves, we can plot the optical path difference, and Fig. 10.7 shows a typical OPD
192
Chapter 10
Figure 10.7 Optical Path Difference for Cooke Triplet Example
plot for our sample Cooke triplet. In addition to the plotted data, we show also perspective views of the three-dimensional wavefront departure from perfect. Note how the curve and the perspective view correlate so well for the on-axis field position with the bump in the center as well as the turned up edge of the wavefront clearly evident in both data. It is a little difficult without extensive experience to quickly determine the residual aberrations from an OPD plot, so you will generally want to compute the more standard ray trace curves for this purpose.
Encircled Energy Encircled energy is energy percentage plotted as a function of image diameter. One good example of how we might use encircled energy is to specify an imaging optical system using a CCD sensor. Let us assume
Computer Performance Evaluation
193
Figure 10.8 Encircled Energy for Cooke Triplet Example
that the pixel pitch of our sensor is 7.5 m. A good reliable and simple specification is that 80% of the energy from a point object shall fall within a diameter of 7.5 m. Figure 10.8 shows an encircled energy plot for our sample Cooke triplet. Eighty percent of the energy is contained within a diameter of approximately 6 m, which is a good match to the sensor. It also leaves some margin for manufacturing tolerances.
MTF MTF is perhaps the most comprehensive of all optical system performance criteria, especially for image forming systems. Figure 10.9 is a representation of what is happening. We begin with a periodic object or target, which is varying sinusoidally in its intensity. This target is imaged by the lens under test, and we plot the resulting intensity pattern at the image. Due to aberrations, diffraction, assembly and alignment errors, and other factors, the imagery will be somewhat degraded and the brights will not be as bright and the darks will not be as dark as the original pattern. Let us define some terms: ImaxImin Modulation Imax Imin
modulation in image MTF modulation in object
194
Chapter 10
Figure 10.9 Illustration of the Meaning of the Modulation Transfer Function
The modulation is simply the maximum intensity minus the minimum intensity divided by the maximum plus the minimum. The MTF is the ratio of the modulation in the image to the modulation in the object as a function of spatial frequency, which is generally in the form of line pairs per millimeter. Thus, the modulation transfer function represents the transfer of modulation from the object to the image by the lens as a function of spatial frequency.. There is another term, contrast (sometimes called contrast ratio), which is given by I (max) Contrast I (min) Figure 10.10 shows several typical MTF curves. We show the MTF of a perfect optical system, a perfect system with a central obscuration (such as a Cassegrain telescope), and a typical real system. The MTF of the perfect obscured system has more diffraction due to its obstruction, and thus a lower MTF. The cutoff frequency, which is where the MTF goes to zero, is 1 cutoff (ƒ/#) The example shown is an ƒ/2 lens in the visible (0.55-m wavelength), and the cutoff frequency is approximately 882 line pairs/mm. A good rule of thumb to remember is that an ƒ/2 lens used at 0.5 m has a cutoff frequency of 1000 line pairs/mm, and it is very easy to scale from here. For example, an ƒ/4 lens has twice the Airy disk diameter and thus half the cutoff frequency of 500 line pairs/mm.
Computer Performance Evaluation
195
Recall that the MTF tells us how well the modulation in the object is transferred to the image by the lens. We show below the MTF curve in Fig. 10.10 a graphical representation of an object and of the resulting image at a low spatial frequency, a midspatial frequency, and at a high spatial frequency. Think of the low spatial frequency as being very large tree trunks with a bright sky between them, and the high spatial frequency as being tiny close tree branches with the same bright sky between them. The sky is the same for both and the darkness of the bark on the tree trunks and the branches is the same, hence the modulation of the objects is identical. However, the modulation of the image will be far lower at the higher spatial frequency of the branches since the MTF is lower. The MTF is generally computed or measured for bars that are radial and for bars that are tangential. The radial bars are like the spokes on a bicycle, and the tangential bars are tangential to the edge of the bicycle tire as well as tangential to the edge of a circular field of view. The tangential and radial bars are orthogonal to each other. There is a subtlety of some
Figure 10.10 Typical MTF Curves
196
Chapter 10 significance with respect to the preceding nomenclature and how we handle it in the various software packages. Consider a lens designed to cover a rectangular format with a 3 4 5 aspect ratio. We said earlier that the radial bars are parallel to spokes on a wheel and tangential bars are orthogonal to the radial bars. This is fine and true, and the definition is valid. How-ever, given the pixelated nature of many of today’s sensors such as CCD or CMOS detector arrays, or alternatively pixelated display devices as used in LCD and similar projection systems, it makes far more sense if the resolution bars and their associated nomenclature were consistent with the pixel rows and columns. What we mean is that it will be far more appropriate to refer to bars that are vertical and bars that are horizontal, rather than radial and tangential as shown in Fig. 10.10. Fortunately, most of the software packages use the terminology sagittal and tangential, and these refer to entrance and exit pupil coordinates. Tangential ray aberrations in the exit pupil are up and down in the plane of the paper in the y direction and sagittal ray aberrations are in and out of the plane of the paper in the x direction. We show in Fig. 10.11 the orientation of the bars using both nomenclatures. Regardless of which software package you use, it is imperative to understand what assumptions are being made with respect to target orientation. The bottom line here is as follows: Tangential aberrations are in the y direction and blur horizontal bars. Tangential bars are horizontal. Sagittal aberrations are in the x direction and blur vertical bars. Sagittal bars are vertical. Radial bars are bars parallel to spokes on a wheel.
Figure 10.11 Target Orientation Conventions
Computer Performance Evaluation
197
Tangential bars are tangent to the rim of a wheel. A good example of a computed MTF and the resulting image quality is shown in Fig. 10.12. Here we plot the MTF of a double Gauss lens at four fields of view (on axis