Nanometer CMOS ICs
Nanometer CMOS ICs From basics to ASICs
Harry Veendrick
~ Springer the languag of sci nee
my businessm edia
Nanometer CMOS ICs Author: Dr. Ir. H.J .M.Veendrick NXP Semicond uctors-Research E-m ail:
[email protected] Cover design: Bram Veendrick Photographs used in cover: NXP Semiconductors Typesetting and layout: Harold Bent en and Dre van den Elshout Illustrations: Kim Veendrick and Henny Alblas First English edition: 2008 This book is based on variou s previous publi cations. The first original 1990 publication (Delt a Press b.v.) was in t he Dutch language. In 1992 a revised , updated and translat ed English edit ion of that book was jointly published by VCR Verlagsgesellschaft (Weinheim, Germany) and VCR Publishers Inc. (NY, USA). The t hird book , ent it led Deep-Submicron CMOS ICs: from Basics to ASICs , was a joint publication of Ten Ragen en St arn, Devent er, The Netherland s, and Kluwer Acad emic Publishers, Boston, USA) and published in two edit ions (1998 and 2000). Thi s new book covers th e same subjects , but t hen t hey are completely revised and upd at ed with the most recent st ate-of-the-art material. It covers all subjects, related to nanomet er CMOS ICs: physics, technologies, design, t esting, packaging and failure ana lysis. The conte nts have increased by almost one third , leading to a much more detailed and complete description of most of th e subjects. Thi s new book is almost full colour .
ISBN 978-1-4020-8332-7
NUR 950
© 2008 Springer , Heidelberg, New York, Tokyo Mybus inessmedia, Deventer, The Netherlands All right s reserved. No part of this book may be reproduced , stored in a da tabase or retrieval system, or published, in any form or in any way, electronically, mechanically, by print , photo print, microfilm or any other means without prior written permission from the publisher. Information pub lished in t his work, in any form , may be subject to patent rights and is int ended for study purposes and privat e use only. Although this book and its conte nts were produced with great care, neither the author nor the publisher can guarantee th at th e information contained therein is free from err ors. Readers are advised to keep in mind th at st at ements , data, illustrations, pro cedural detai ls or other items may inadvertently cont ain inaccuracies. This book cont ains many sources and references of t ext , photographs and illustrations. Although the author has given a lot of atte nt ion to carefully refer to t he source of related material, he already apologi zes for th e one or few individu al occasions that this has slipp ed his final review.
Foreword CMOS scaling is now entering the deca-nanometer era. This enables the design of systems-on-a-chip containing more than 10 billion transistors. However, nanometer level device physics also causes a plethora of new challenges that percolate all the way up to the system level. Therefore system-on-a-chip design is essentially teamwork requiring a close dialogue between syst em designers, software engineers , chip architects, intellectual property providers, and process and device engineers. This is hardly possibl e without a common understanding of the nanometer CMOS medium, its terminology, its future opportunities and possible pitfalls. This is what this book provides . It is a greatly extended and revised version of the previous edition that was addressing deep-submicron CMOS systems. So besides the excellent coverage of all basic aspects of MOS devices, circuits and systems it leads the reader into the novel intricacies resulting from scaling CMOS down to the deca-nanometer level. New in this edition is the attention to the issues of increased leakage power and its mitigation, to strain induced mobility enhancement and to sub45 nm lithographic techniques. Immersion and double patterning litho the use of high index fluids as well as of extreme UV and other altern at ive litho approaches for sub 32 nm are extensively discussed together with their impact on circuit layout. The design section now also extensively covers design techniques for improved robustness, yield and manufacturing in view of increased device variability, soft errors and decreased reliability when reaching atomic dimensions. In the packaging section attention is paid to rapidly emerging 3D integration techniques. Finally the author shares his thoughts on the challenges of further scaling when approaching the end of the CMOS roadmap by 2015. This book is unique in that it covers in a very comprehensive way all aspects of the trajectory from process technology to the design and packaging of robust and testable systems in nanometer scale CMOS . It is the reflection of the author's own research in this domain but also of almost 30 years experience in interactive teaching of CMOS design to NXP and PHILIPS system designers and process engineers alike. It provides context and perspective to both sides . I strongly recommend this book to all engineers involved in the design and manufacturing of future systems-on-silicon as well as to engineering undergraduates who want to understand the basics that make electronics systems work. Leuven, February 2008 Hugo De Man Professor Emeritus K.U . Leuven Senior Fellow IMEC Leuven Belgium v
Preface An integrated circuit (IC) is a piece of semiconductor material, on which a number of electronic components are interconnected. These interconnected 'chip' components implement a specific function. The semiconductor material is usually silicon but alternatives include gallium arsenide. ICs are essential in most modern electronic products. The first IC was created by Jack Kilby in 1959. Photographs of this device and the inventor are shown in figure 3. Figure 1 illustrates the subsequent progress in IC complexity. This figure shows the numbers of components for advanced ICs and the year in which these ICs were first presented. This doubling in complexity every two years was predicted by Moore (Intel 1964), who's law is still valid today for the number of logic transistors on a chip . However, due to reaching the limits of scaling, the complexity doubling of certain memories now happens at a three-year cycle. This is shown by the complexity growth line which is slowly saturating. Figure 2 shows the relative semiconductor revenue per IC category. CMOS ICs take about 75% of the total semiconductor market . Today's digital ICs may contain several hundreds of millions to more than a billion transistors on one single 1 cm 2 chip. They can be subdivided into three categories: logic, microprocessors and memories . About 10% of the CMOS ICs are of an analog nature. Figures 4 to 7 illustrate the evolution in IC technology. Figure 4 shows a discrete BCI07 transistor. The digital filter shown in figure 5 comprises a few thousand transistors while the Digital Audio Broadcasting (DAB) chip in figure 6 contains more than six million transistors. The Intel Pentium4 Xeon dual-core processor in figure 7.25 (section 7.6), contains 1.3 billion transistors. Figure 7 shows an 8 Gb 63 nm multi-level NAND-flash memory chip. Figure 8 illustrates the sizes of various semiconductor components, such as a silicon atom, a single transistor and an integrated circuit, in perspective. The sizes of an individual MaS transistor are approaching the details of a virus.
vi
2T IT 156G 64G 16G 4G IG ...... 256 ~I :... ~ 64 M
:::..
~
::: ~ :::
~ ::.
~ '-'
'C'
c vpcctcd capa"-II)
(:)'4.cg~ii 6 Gbil
.0';Gbil
0~56 Mbil
•• •••0 64 Mbil 16 Mbil .04Mbil .0 " Mbil
/:J
156k Mk 16 k
....0
H Il
4
i;;, ( ibn
....A:>' .. , J:J'/>4 (;~II
16 .\1 4 ~l I ~I
156 64 16
?
li e ......· •
II
t:1' 15bLbil .6 64 kbil II>-kbil MO · DRA t
.,.6 I·kbil MO · DRAM
Ii"
/fJ
4·bil ITl-coonlcr
dua l flip- flop
:f!) RTl gale
\Ul , "" I -f-=-,...L--' '-=+---=:::;----L,.--...:.;:r'---,-.,.---,r--r- -.-- .,.---,r--r- -
1959 1965 1970 1975 19S0 19S5 19'10 1995 2000 2005 2010 1015 2020 1025
year
Figure 1: Growth in the number of components per IC
Di crete :::15.0%
Co mpound ::: 1%
..
Bipolar e 7%
Integrated Circ uits :::85% of the Total larket
MO :::92% of the integraded ircuit Market
Analog MO :::9%
1 Digital :::9 1% o f MOS
Figure 2: Relative semiconductor revenue by IC category (Source: IC Insights)
Vll
This book provides an insight into all aspects associated with CMOS ICs . The topics presented include relevant fundamental physics. Technology, design and implementation aspects are also explained and applications are discussed. CAD tools used for the realisation of ICs are described while current and expected developments also receive attention. The contents of this book are based on the CMOS section of an industry-oriented course entitled 'An introduction to IC techniques'. The course has been given almost three decades, formerly in Philips, currently in NXP Semiconductors. Continuous revision and expansion of the course material ensures that this book is highly relevant to the IC industry. The level of the discussions makes this book a suitable introduction for designers , technologists, CAD developers, test engineers, failure analysis engineers, reliability engineers, technical-commercial personnel and IC applicants. The text is also suitable for both graduates and undergraduates in related engineering courses. Considerable effort has been made to enhance the readability of this book and only essential formulae are included. The large number of diagrams and photographs should reinforce the explanations. The design and application examples are mainly digital. This reflects the fact that more than 90% of all modern CMOS ICs are digital circuits. However, the material presented will also provide the analogue designer with a basic understanding of the physics, manufacture and operation of nanometer CMOS circuits. The chapters are summarised below. For educational purposes the first four chapters each start with a discussion on nMOS physics, nMOS transistor operation, nMOS circuit behaviour, nMOS manufacturing process, etc. Because the pMOS transistor operation is fully complementary to that of the nMOS transistor, it is then easier to understand the operation and fabrication of complementary MOS (CMOS) circuits. The subjects per chapter are chosen in a very organised and logical sequence so as to gradually built the knowledge, from Basics to ASICs. The knowledge gathered from each chapter is required to understand the information presented in the next chapter(s) . Each chapter ends with a reference list and exercises. The exercises summarise the important topics of the chapter and form an important part of the complete learning process. Chapter 1 contains detailed discussions of the basic principles and fundamental physics of the MOS transistor. The derivation of simple current-voltage equations for MOS devices and the explanation of their characteristics illustrates the relationship between process parameters
Vlll
and circuit performance. The cont inuous redu ction of transistor dimensions leads to increased deviation between the performance predicted by the simple MOS formulae and actual transistor behaviour. The effects of temp erature and the impact of the cont inuous scaling of the geometry on this behaviour are explained in chapte r 2. In addition to their influence on transistor and circuit perform ance, t hese effects can also reduce device lifetime and reliability. The various technologies for the manufacture of CMOS ICs are examined in chapte r 3. After a summary on the available different substrat es (wafers) used as starting material, an explanation of the most important associated photolithographic and processing steps is provid ed. This precedes a discussion of an advanced nanom et er CMOS technology for the manufacture of modern VLSI circuits. The design of CMOS circuits is treated in chapter 4. An introduction to the performance aspects of nMOS circuits provides an ext remely useful background for the explanat ion of the CMOS design and layout procedures. MOS technologies and th eir derivatives are used to realise the special devices discussed in chapter 5. Charge-coupled devices (CCDs) , CMOS imagers and MOS power transistors are among t he special devices. Chapter 5 conclude s the presentation of the fund ament al concepts behind BICMOS circuit operation. Stand-alone memories currently repr esent about 25% of the tot al semiconductor market revenue. However , also in logic and microprocessor les embedded memories repr esent close to 80% of th e total transistor count . So, of all transistors produced in the world, tod ay, about 90% end up in either a st and-alone, or in an embedded memory. This share is expected to st ay at thi s level or to increase. The majority of available memory types are t herefore examined in chapter 6. The basic structures and the operating principles of th e various typ es are explained. In addit ion, the relationships between t heir respective prop erties and applicat ion areas is made clear. Development s in IC technology now facilitate the int egration of complete syst ems on a chip, which contain several hundreds of millions to more than a billion of transistors. The various IC design and realisation t echniqu es used for these VLSI ICs are present ed in chapter 7. The advantages and disadvantages of the techniqu es and the associated CAD tools are examined. Various modern technologies ar e used to realise a
IX
separate class of VLSI ICs, which are specified by applicants rather than manufacturers. These application-specific ICs (ASICs) are examined in this chapter as well. Motives for their use are also discussed. As a result of the continuous increase of power consumption, the maximum level that can be sustained by cheap plastic packages has been reached. Therefore, all CMOS designers must have a 'less-power attitude'. Chapter 8 presents a complete overview of less-power and less-leakage options for CMOS technologies, as well as for the different levels of design hierarchy. Increased VLSI design complexities, combined with higher frequencies create a higher sensitivity to physical effects. These effects dominate the reliability and signal integrity of nanometer CMOS ICs. Chapter 9 discusses these effects and the design measures to be taken to maintain both reliability and signal integrity at a sufficiently high level. Finally, testing, yield , packaging, debug and failure analysis are important factors that contribute to the ultimate costs of an IC. Chapter 10 presents an overview of the state-of-the-art techniques that support testing, debugging and failure analysis. It also includes a rather detailed summary on available packaging technologies and gives an insight into their future trends. Essential factors related to IC production are also examined; these factors include quality and reliability. The continuous reduction of transistor dimensions associated with successive process generations is the subject of the final chapter (chapter 11). This scaling has various consequences for transistor behaviour and IC performance. The resulting increase of physical effects and the associated effects on reliability and signal integrity are important topics of attention. The expected consequences of and road blocks for further miniaturisation are described. This provides an insight into the challenges facing the IC industry in the race towards nanometer devices . Not all data in this book is completely sprout from my mind . A lot of books and papers contributed to make the presented material stateof-the-art. Considerable effort has been made to make the reference list complete and correct. I apologize for possible imperfections. Acknowledgements I wish to express my gratitude to all those who contributed to the realisation of this book; it is impossible to include all their names. I greatly value my professional environment: Philips Research labs, of which the semiconductor research department is now part of NXP Semiconductors.
x
It offered me the opportunity to work with many internationally highly valued colleagues who are all real specialists in their field of semiconductor expertise. Their contributions included fruitful discussions, relevant texts and manuscript reviews. I would like to make an exception, here, for my colleagues Marcel Pelgrom and Maarten Vertregt, who greatly contributed to the discussions held on trends in MOS transistor currents and variability matters throughout this book and Roger Cuppens and Roelof Salters for the discussions on non-volatile and random-access memories , respectively. I would especially like to thank Andries Scholten and Ronald van Langevelde for reviewing chapter 2 and for the discussions on leakage mechanisms in this chapter, Casper Juffermans and Johannes van Wingerden for their inputs to and Ewoud vreugdenhil (ASM Lithography) for his review of the lithography section in chapter 3. I would also like to sincerely thank Robert Lander for his detailed review of the section on CMOS process technologies and future trends in CMOS devices and Gerben Doornbos for the correct sizes and doping levels used in the manufacture of state-of-the-art CMOS devices. I appreciate the many circuit simulations that Octavio Santana has done to create the tapering-factor table in chapter 4. I am grateful for the review of chapter 5 on special circuits and devices based on MOS transistor operation: Albert Theuwissen (Harvest Imaging) for the section on CCD and image sensors , Johan Donkers and Erwin Hijzen for the BICMOS section and Jan Sonsky for the high voltage section. I also appreciate their willingness to supply me with great photographic material. Toby Doorn and Ewoud Vreugdenhil are thanked for their review of the memory chapter (chapter 6). I appreciate Paul Wielage's work on statistical simulations with respect to memory yield loss. I thank Ad Peeters for information on and reviewing the part on asynchronous design in the low-power chapter (chapter 8). Reliability is an important part of chapter 9, which discusses the robustness of ICs. In this respect I want to thank Andrea Scarpa for reviewing the hot-carrier and NBTI subjects, Theo Smedes for the ESD and latch-up subjects and Yuang Li for the part on electromigration. I also greatly value the work of Bram Kruseman , Henk Thoonen and Frank Zachariasse for reviewing the sections on testing, packaging and failure analysis, respectively. I also like to express them my appreciation for supplying me with a lot of figures and photographs, which support and enrich the discussions on these subjects in chapter 10. Finally, I want to thank Chris Wyland and John Janssen,
xi
for their remarks and additions on electrical and thermal asp ects of Ie packages, respectively I am very grateful to all those who attended the course, because their feedback on educational aspects, their corrections and constructive criticism contributed to the quality and completeness of this book. In addition, I want to thank Philips Research and NXP Semiconductors, in general for the co-operation I was afforded. I thank my son Bram for the layout of the cover and the layout diagrams in chapter 4, and Ron Salfrais for the correctness of a large part of the English text . I would especially like to express my gratitude to my daughter Kim and Henny Alblas for the many hours they have spent on the creation of excellent and colourful art work, which contributes a lot to the quality and clarity of this book. Finally, I wish to thank Harold Benten and Dre van den Elshout for their conscientious editing and type-setting work. Their efforts to ensure high quality should not go unnoticed by the reader. However, the most important appreciation and gratitude must go to my family, again, and in particular to my wife, for her years of exceptional tolerance, patience and understanding. The year 2007 was particularly demanding. Lost hours can never be regained , but I hope that I can give her now a lot more free tim e in return. Harry J .M. Veendrick
Eindhoven, February 2008
xii
Fi gure 3: Th e developm ent of the first IC: in 1958 Jack Kilby demonstrated the feasibility of resistors and capacitors, in addition to transistors, based on semi conductor technology. Kil by, an employee of Texas Instrum ents, submitted the patent request entitled 'Miniaturized Electronic Circuits ' in 1959. His request was honoured. Recognition by a number of Japanese companies in 1990 means that Texas Instrum ents is still benefiting from Kilby 's patent (Source: Texas Instrum ents / Koning & Hartm an).
Xlll
Figure 4: A single BC107 bipolar transistor (Source: NXP Semiconductors)
XIV
Figure 5: A digital filter which com prises a few thou sand transistors (Source: NX P Semicondu ctors)
xv
Figure 6: A Digital Audio Broadcasting (DAB) chip, which comprises more th an six million transistors (Source: NXP Semiconductors)
xvi
Figure 7: An 8 Gb 63nm ML C NAND Chip Layou t (Source: Samsung)
xv ii
-~-100nm
IOOllm
Fi gure 8: Various semiconductor com ponent sizes (e.g., atom, transistor, int egrated circuit) in perspective
XV lll
Overview of symbols
a A A a (3 (30 (3n (3p (3total BV C Cb Cd Cdb
Cg Cgb Cgd Cgs Cgdo
Cgso C par C min
Cs Cox
C; Csb
Ct CD !:lL !:l VT Do
chann el-shor tening factor or clustering factor area aspect ratio activity factor MOS transistor gain factor gain factor for MOS tr ansistor with square channel nMOS transistor gain factor pMOS t ra nsistor gain factor equivalent gain factor for a combination of t ra nsistors breakdown voltage capacitance bitline capacitance depletion layer capacitance dr ain-substrate capacitance gate capacitance gate-substrate capacitance gate-drain capacitance gate-source capacitance voltage-independent gate-drain capacitance voltage-independent gate-source capacitance parasitic capacitance minimum capacitance scaled capacitance oxide capacitance silicon sur face-inte rior capacitance source-substrate (source-bulk) volt age total capacitance crit ical dimension difference between drawn and effective channel length t hreshold volt age variat ion defect density for uniformly distri buted errors (dust particles) xix
tax tr tsi
E Ec Er
z; Em x Eox Ev
Ex Ex c
s; cP
cPr cPs cPMS F
f fm ax
'Y
gm I
h Ids IdsO Ids 0 IdsL
Ids sat Idssub
I m ax Ion
IR i(t)
threshold-voltage channel-length dependence factor threshold-voltage channel-width dependence factor dielectric constant absolute permittivity relative permittivity of oxide relative permittivity relative permittivity of silicon electric field strength conduction band energy level Fermi energy level intrinsic (Fermi) energy level maximum horizontal electric field strength electric field across an oxide layer valence band energy level horizontal electric field strength critical horizontal field strength vertical electric field strength electric potential Fermi potential surface potential of silicon w.r.t. the substrate interior contact potential between gate and substrate feature size (= size of a half pitch used for stand-alone memories)) clock frequency maximum clock frequency factor which expresses relationship between drain-source voltage and threshold-voltage variation transconductance current substrate current drain-source current characteristic sub-threshold current for gate-substrate voltage of 0 V driver transistor drain-source current load transistor drain-source current saturated transistor drain-source current sub-threshold drain-source current maximum current on current current through resistance time-dependent current
xx
j
cur rent densisty k Boltzman's constant K K-factor; expresses relationship between source -subst rate volt age and threshold voltage amplificat ion factor K wavelength of light A effect ive transistor channel length and inductance L channel length reduction due to channel length modulation LCLM effect ive channel length L eff effect ive channel length of reference transistor Lref yield mod el par am eter !vI substrate carrier mobili ty /10 channel elect ron mobility /1n channel hole mobility /1p subst ra te doping concent rat ion NA numeric aperture N.A. charge density P power dissipati on P dynamic power dissipation Pdy n Pst at static power dissipation volt age scaling factor p charge Q q elementary cha rge of a single elect ron depletion layer charg e Qd gate cha rge Qg total mobil e cha rge in t he inversion layer Qrn mobil e cha rge per uni t area in t he channel Qn oxide cha rge total cha rge in t he semiconductor Qs resistan ce R junction-to-air thermal resistance RJA junction-to-case thermal resist an ce RJ C load resistance RL output resist an ce or cha nnel resist an ce Rout R th errn t hermal resist an ce of a package t apering factor r S scale factor Ssubth r sub-t hreshold slope delay time T
a;
xxi
fall time rise time TR dielectric relaxation time T clock period Tmin minimum clock period T emp te mperature T empi; ambient tem perature T empe case te mperature T empJ junction tem perature 1if t ra nsistor lifeti me t time t cond conducto r thickness t« depletion layer t hickness t d ielectric dielectric thickness t ox gate-oxide t hickness ti s isolat or thickness U comput ing power v carrier velocity Vsat car rier saturation velocity V voltage VB breakdown voltage v;. scaled voltage Va deplet ion layer voltage substrate voltage Vbb Vdd supply voltage ~ voltage at silicon surface Vd s dr ain-source voltage Vdssat drain-source voltage of saturated t ransistor VE Early voltage Vf b flat-band volt age Vg gate voltage Vgg ext ra supply volt age gat e-source volt age Vgs VgsL load t ra nsistor gate-source volt age VH high voltage level Vin input voltage Vj junction voltage VL low voltage level VPT t ra nsistor pu nch-through voltage Tf
Tr
XX ll
~b ~s
Vws VT VTo VT d ep
VT e n h VT L VTn VT p
VT pa r Vout V(X) Vx VX L VXo
W Wn Wp Wref W
L
Cf)n (If)p x y
z,
source-substrate (back-bias) voltage ground voltage well-source voltage threshold voltage driver transistor threshold voltage depletion transistor threshold voltage enhancement transistor threshold voltage load transistor threshold voltage nMOS transistor threshold voltage pMOS transistor threshold voltage parasitic transistor threshold voltage output voltage potential at position x process-dependent threshold voltage term process-dependent threshold voltage term for load transistor process-dependent threshold voltage term for driver transistor transistor channel width nMOS transistor channel width pMOS transistor channel width reference transistor channel width transistor aspect ratio nMOS transistor aspect ratio pMOS transistor aspect ratio distance w.r.t. specific reference point yield input impedance
xxiii
List of physical constants
EO Eox
Esi
cPr k q
= 8.85 X 10- 12 F j m
= 4 for silicon dioxide = 11.7 = 0.5 V for silicon substrate = 1.4 X 10- 23 JoulejK = 1.6 X 10- 19 Coulomb
xxiv
Contents v
Forewo rd
vi
Preface
xi x
Overview of sym b ols List of physical constants
x xiv
1 B a sic P rinciples 1.1 Introduct ion . . . . . . . . . . . . . . 1.2 The field-effect prin ciple . . . . . . . 1.3 The inversion-layer MaS tra nsisto r . 1.3.1 T he Metal-Oxide-Semiconducto r (MaS) capacitor " 1.3.2 The inversion-layer Ma S t rans istor 1.4 Derivation of simple Ma S formulae. . . . . . . . . . . . . 1.5 The back-bias effect (back-gate effect, body effect) and the effect of forward-bias " 1.6 Factors which characterise t he behaviour of t he MaS transist or. . . . . . . . . . . . . . . . . 1.7 Different typ es of MaS transistors 1.8 Parasitic MaS tr ansistors . . . . 1.9 MaS transistor symbols . . . . . 1.10 Capacitances in MaS structures 1.11 Conclusions 1.12 References . 1.13 Exercises .
1 1 1 4 11 15 23 27 30 32 34 36 38 48 49 50
2 Geometrical- , physi cal- and field-scaling impact on MOS t r a nsist or behaviour 57 2.1 Introduction . .. . . . . . . . . . .. . . . . . . . . . . . . 57 xxv
The zero field mobili ty . . . .. .. Carrier mobili ty reduction. .. 2.3.1 Vertical and lat eral field carrier mobility redu ction 2.3.2 St ress-induced carrier mobility effects 2.4 Channel length modulation 2.5 Short- and narrow-channel effects . 2.5.1 Short-channel effects . 2.5.2 Narrow-cha nnel effect 2.6 Temp erature influence on carrier mobility and threshold voltage . 2.7 MaS transist or leakage mechanisms 2.7.1 Weak-inversion (subthreshold ) behaviour of the MaS transistor . 2.7.2 Gate-oxide tunnelling 2.7.3 Reverse-bias junction leakage 2.7.4 Gate-induced dr ain leakage (GIDL) 2.7.5 Impact Ionisation . 2.7.6 Overall leakage int eractions and considerations 2.8 MaS transistor models . 2.9 Conclusions 2.10 References . 2.11 Exercises 2.2 2.3
3
Manufacture of M OS devices 3.1 Introduct ion. . . . . . . . . . .. .. . . . . . . . 3.2 Different substrates (wafers) as starting material 3.2.1 Wafer sizes . . . . . . . . . . . . . . . . . 3.2.2 Standard CMOS Ep i . . . . . . . . . . . . 3.2.3 Cryst alline orientation of the silicon wafer 3.2.4 Silicon-on-insulator (Sal) 3.3 Lithography in MaS processes . . . . . . . . . . 3.3.1 Lit hography basics . . . . . . . . . . . . . 3.3.2 Lithographic alte rn at ives beyond 40 nm . 3.3.3 Next generation lit hography. . . . . . . . 3.3.4 Mask cost redu ct ion techniques for low-volume produ ction . 3.4 Etching . . . 3.5 Oxidation . . . . 3.6 Deposition . .. . 3.7 Diffusion and ion impl ant ation .
xxv i
58 59 59 63 64 66 66 69 71 74 75 78 80 81 82 83 86 88 89 91 93 93 95 95 95 98 99 105 105 121 124
126 131 134 137 142
3.8 Planarisation . . . . . . . . . . . . . . . . . . . 3.9 Basic MOS technologies . . . . . . . . . . . . . . 3.9.1 The basic silicon-gate nMOS process. 3.9.2 The basic Complementary MOS (CMOS) process. 3.9.3 An advanced nanometer CMOS process . . 3.9.4 CMOS technology options beyond 45nm . . 3.10 Conclusions . 3.11 References . . 3.12 Exercises . .
4 CMOS circuits 4.1 Introduction... . . . . . 4.2 Th e basic nMOS inverter 4.2.1 Introduction . .. 4.2.2 The DC behaviour 4.2.3 Comparison of the different nMOS inverters . 4.2.4 Transforming a logic function into an nMOS transistor circuit 4.3 Electrical design of CMOS circuits 4.3.1 Introduction . . . . 4.3.2 The CMOS inverter 4.4 Digital CMOS circuits . . . 4.4.1 Introduction . . . . 4.4.2 Static CMOS circuits 4.4.3 Clocked static CMOS circuits . 4.4.4 Dynamic CMOS circuits . . . . 4.4.5 Other types of CMOS circuits. 4.4.6 Choosing a CMOS implementation 4.4.7 Clocking strategies . . . . . . . . 4.5 CMOS input and output (I/O) circuits. 4.5.1 CMOS input circuits. . . . . . 4.5.2 CMOS output buffers (drivers) 4.6 The layout process . . . . . 4.6.1 Introduction . . . . 4.6.2 Layout design rules. 4.6.3 Stick diagram . . . . 4.6.4 Example of the layout procedure 4.6.5 Guidelines for layout design 4.7 Conclusions 4.8 References . . . .. .. XXVII
. . . . .
146 153 153 158 160 168 178 179 183
185 185 186 186 188 196
. 197 . 200 . 200 . 201 . 218 . 218 . 219 . 225 . 228 . 234 . 235 . 236 . 237 . 237 . 238 . 240 . 240 . 241 . 245 . 248 . 252 . 254 . 255
4.9
Exercises
.
. 257
5 Special circuits, devices and technologies 5.1 Introduction .. .. . . . . . . . 5.2 CCD and CMOS image sensors 5.2.1 Introduction . . . . . 5.2.2 Basic CCD operation 5.2.3 CMOS image sensors . 5.3 Power MOSFET transistors . 5.3.1 Introduction .. . . . 5.3.2 Technology and operation 5.3.3 Applications .. 5.4 BICMOS digital circuits . . 5.4.1 Introduction .. .. 5.4.2 BICMOS technology 5.4.3 BIGMOS characteristics 5.4.4 BICMOS circuit performance 5.4.5 Future expectations and market trends. 5.5 Conclusions 5.6 References. 5.7 Exercises
261 . 261 . 262 . 262 . 262 . 267 . 270 . 270 . 271 . 274 . 275 . 275 . 276 . 279 . 280 . 283 . 284 . 285 . 287
6 Memories 6.1 Introduction .. . . . . . . . . . . . . . 6.2 Serial memories . . . . . . . . . . . . . 6.3 Content-addressable memories (CAM) 6.4 Random-access memories (RAM) 6.4.1 Introduction 6.4.2 Static RAMs (SRAM) . . 6.4.3 Dynamic RAMs (DRAM) 6.4.4 High-performance DRAMs 6.4.5 Single- and dual port memories 6.4.6 Error sensitivity 6.4.7 Redundancy .. 6.5 Non-volatile memories 6.5.1 Introduction .. 6.5.2 Read-Only Memories (ROM)
. . . . . . . . . . . . . .
289 289 293 294 294 294 294 310 321 327 328 328 329 329 329
6.5.3
Programmable Read-Only Memories
. 334
6.5.4 6.5.5
EEPROMs and flash memories Non-volatile RAM (NVRAM) .
. 337 . 345
xxviii
6.6 6.7 6.8 6.9 6.10
6.5.6 BRAM (battery RAM) 6.5.7 FRAM , MRAM, PRAM (PCM) and RRAM Embedded memories . . . . . . . . . . Classification of the various memories Conclusions References. Exercises .
. . . . . . .
346 346 350 353 355 357 362
7 Very Large Scale Integration (VLSI) and ASICs 365 7.1 Introduction . . . . . . . . . . 365 7.2 Digital ICs . 368 7.3 Abstraction levels for VLSI . 373 7.3.1 Introduction . . . 373 7.3.2 System level . . . . 376 7.3.3 Functional level . . 379 7.3.4 RTL level . . . . . 380 7.3.5 Logic-gate level . . 383 7.3.6 Transistor level . 384 7.3.7 Layout level. . 386 7.3.8 Conclusions. . 386 7.4 Digital VLSI design . 389 7.4.1 Introduction . 389 7.4.2 The design trajectory and flow . 389 7.4.3 Example of synthesis from VHDL description to layout . . . . . . . . . . . . . . . 394 7.5 The use of ASICs . . . . . . . . . . . . . 402 7.6 Silicon realisation of VLSI and ASICs . 403 7.6.1 Introduction . 403 7.6.2 Hand crafted layout implementation . 406 7.6.3 Bit-slice layout implementation . . . . 407 7.6.4 ROM, PAL and PLA layout implementations . 408 7.6.5 Cell-based layout implementation. . . . . . 413 7.6.6 (Mask programmable) gate array layout implementation . . . . . . . . . . . . . . . . . . . . . . . 415 7.6.7 Programmable Logic Devices (PLDs) 420 7.6.8 Embedded Arrays , Structured ASICs and platform ASICs . . . . . . . . . . . . . . . . . . . . 434 7.6.9 Hierarchical design approach . 438 7.6.10 The choice of a layout implementation form . 439 . . . . . . . . . . . . . . 443 7.7 Conclusions. .. . .. XXIX
7.8 7.9
8 Low 8.1 8.2 8.3 8.4
8.5
8.6 8.7 8.8 8.9
References . Exercises .
.444 .445
power, a hot topic in IC design 447 Introduction.............. . 447 Battery technology summary . . . . . 448 Sources of CMOS power consumption . 450 Technology options for low power . . . . 452 8.4.1 Reduction of l1eak by technological measures . 452 8.4.2 Reduction of Pdyn by technology measures . . . 457 8.4.3 Reduction of Pdyn by reduced-voltage processes . 459 Design options for power reduction . . . . . . . . . . . . 462 8.5.1 Reduction of Pshort by design measures . . . . . . 462 8.5.2 Reduction/elimination of P stat by design measures 464 8.5.3 Reduction of P dyn by design measures 465 Computing power versus chip power, a scaling perspective 501 Conclusions . 504 References. . 505 Exercises . . 509
9 Robustness of nanometer CMOS designs: signal integrity, variability and reliability 511 9.1 Introduction 511 9.2 Clock generation, clock distribution and critical timing. . 513 9.2.1 Introduction 513 514 9.2.2 Clock distribution and critical timing issues 9.2.3 Clock generation and synchronisation in different (clock) domains on a chip . . . . . . 523 9.3 Signal integrity . . . . . . . . . . . . . . . . . . . . 527 . 528 9.3.1 Cross-talk and signal propagation . . . . . . 535 9.3.2 Power integrity, supply an ground bounce . 539 9.3.3 Substrate bounce . . 542 9.3.4 EMC . .543 9.3.5 Soft errors . .547 9.3.6 Signal integrity summary and trends .550 9.4 Variability... .. . . . . . . . . . . . . 9.4.1 Spatial vs. time-based variations . 550 . 550 9.4.2 Global vs. local variations .. .. 9.4.3 Transistor matching . . . . . . . .554 9.4.4 From deterministic to probabilistic design .557 xxx
9.4.5 Can the variability problem be solved? . 9.5 Reliability . . .. . . . . 9.5.1 Punch-through.. . .. 9.5.2 Electromigration . . . . 9.5.3 Hot-carrier degradation 9.5.4 Negative bias temperature instability (NBTI) 9.5.5 Latch-up 9.5.6 Electro-Static Discharge (ESD) . . . . . . . . 9.5.7 Charge injection during th e fabrication process 9.5.8 Reliability summary and trends . 9.6 Design organisation. 9.7 Conclusions 9.8 References. 9.9 Exercises .
. . . . . . . . . . . . . .
559 559 560 560 563 568 569 573 578 578 579 581 583 587
10 Testing, yield, packaging, debug and failure analysis 589 10.1 Introduction . . . . . . . 589 10.2 Testing . 591 10.2.1 Basic IC tests. . . . . . 594 10.2.2 Design for testability . . 608 10.3 Yield . . . . . . . . . . . . . . . 610 10.3.1 A simple yield model and yield control. . 614 10.3.2 Design for manufacturability . 620 10.4 Packaging . . . . . . . . . . 623 10.4.1 Introduction . 623 10.4.2 Package categories . . . . 624 . 627 10.4.3 Packaging process flow . 10.4.4 Electrical aspects of packaging . 633 10.4.5 Thermal aspects of packaging . . 635 10.4.6 Reliability aspects of packaging . . 637 10.4.7 Future trends in packaging technology . 639 10.4.8 System-on-a-chip (SoC) versus system-in-a-package (SiP) . . . . . . . . . . . . . . . . . . . . . 641 10.4.9 Quality and reliability of packaged dies . 645 10.4.10 Conclusions . . . . . . . . 647 10.5 Potential first silicon problems . 648 10.5.1 Problems with testing . . . . . . . . . . . 648 10.5.2 Problems caused by marginal or out-of-specification processing . . . . . . . . . . . . . 650 10.5.3 Problems caused by marginal design . . . . . . . . 653 xxxi
10.6 First-silicon debug and failure analysis . 10.6.1 Introduction . 10.6.2 Iddq and Ll1ddq testin g . . . . . . 10.6.3 Traditional debug, diagnosis and failure analysis (FA) t echniques 10.6.4 More recent debug and failure analysis techniques 10.6.5 Observing the failure. . . . . . . . . . . . . . . . . 10.6.6 Circuit edit ing t echniques 10.6.7 Design for Debug and Design for Failure Analysis . 10.7 Conclusions . 10.8 References. . 10.9 Exercises . .
654 654 654 655 664 675 679 682 683 684 686
11 Effects of scaling on MOS Ie design and consequences for the roadmap 687 11.1 Introduction. . . . . . . . . . . 687 . 689 11.2 Transistor scaling effects . . . 11.3 Interconnection scaling effects . 690 11.4 Scaling consequences for overall chip performance and robustn ess . .695 11.5 Potenti al limit ati ons of t he pace of scaling .702 11.6 Conclusions .708 11.7 References . . 709 11.8 Exercises . . 710
XXXll
Chapter 1
Basic Principles 1.1
Introduction
The majority of current VLSI Very Large Scale Integration) circuits are manufactured in CMOS t echnologies. Familiar examples are memories (1 Gb , 4 Gb and 16 Gb) , micropro cessors and signal processors. A good fund ament al treat ment of basic MOS devices is therefore essential for an und erst anding of t he design and manufacture of modern VLSI circuits. This chapter describ es the operation and characte rist ics ofMOS devices. The material requir ement s for their realisation are discussed and equations that predict their behaviour are derived. The acronym MOS repr esents the Met al, Oxide and Semiconductor materials used to realise early versions of the MOS transistor. The fund ament al basis for the operation of MOS transistors is the field-effect prin ciple. This principle is quite old, with relat ed publications first appearing in the ninet een-thirties. These include a patent applicat ion filed by J.E. Lilienfeld in Canada and the USA in 1930 and one filed by O. Heil, independentl y of Lilienfeld, in England in 1935. At t hat t ime, however , insufficient knowledge of mat erial prop erties resulted in devices which were unfit for use. The rapid development of elect ronic valves probably also hind ered th e development of t he MOS tr ansistor by largely fulfilling the tr ansistor's envisaged role.
1.2
The field-effect principle
The field-effect principle is explained with the aid of figur e 1.1. This figure shows a rectangular conductor, called a channel, with length L, 1
width W and t hickness t cond ' The free elect rons present in t he cha nnel are t he mobile charge carriers. There are n electrons per m3 and t he cha rge q per elect ron equals -1.602 x 10- 19 C(coulomb). The applicat ion of a horizontal elect ric field of magnitude E t o the cha nnel causes the elect rons to acquire an average velocity v = - fLn . E . The electron mobility fLn is positive. The direction of v t herefore opposes t he dir ection of E . The resulting current density j is the product of t he average elect ron velocity and the mobile cha rge density p: j
= p . v = - n . q . fLn . E
(1.1)
t·I
-r-+-./ tcond
Figur e 1.1: The field-effect principle A gate electrode sit uated above t he cha nnel is sepa rated from it by an insulator of thickness tis' A cha nge in the gate volt age Vg influences the cha rge density p in the chann el. The current density j is therefore determined by Vg . Example: Suppose the insulator is silicon dioxide (Si0 2 ) wit h a thickness of 2 nm (tis = 2 x 1O- 9m). The gate capacitance will then be about 17 mF 1m2 . T he total gate capacitance Cg is therefore expressed as follows:
Cg
= 17 X 10- 3 .
W . L [F]
A cha nge in gate charge b..Qg = - Cg . b.. Vg causes t he following cha nge in channel cha rge:
+ Cg . b.. Vg = 17 X 10- 3 . W . L . b.. Vg = 2
W · L . t cond . b..p
Thus: 17
10- 3 . ~ V;g
X
C/m3
t cond
and: A Iu n
I = I -~p I=
10.6
16
X
q
10
.
~ Vg eectrons 1 / m3
t cond
If a 0.5 V change in gate voltage is t o cause a hundred times increase in current density i, t hen the following must apply: ~j
J ::::} tcond
=
~p
~n
p
n
10.6
X
1016 . 0.5
t cond .
n
100
5.3 x 1014 n
Examination of two materials reveals the implications of this expression for t cond :
Case a The channel material is copper. Thi s has n :=:::! 1028 elect rons/rn'' and hence tcond :=:::! 5.3 X 10- 14 m. The requir ed cha nnel t hickness is thus less tha n the size of one at om ( :=:::! 3 x 10- 10 m) . Thi s is impossible to realise and its excessive numb er of free carriers renders copper unsuitable as channel material. Case b The channel mat erial is 5ncm n-typ e silicon. This has n :=:::! 1021 electrons/rn'' and hence t cond :=:::! 530 nm . The transcondu ctance 9m of a MOS t ra nsist or is t he rat io of a change in channel (dr ain) curre nt to the corres ponding change in gate volt age: 9m =
However
If 1= i W·
t cond =
~Vg
~I
~j
I
J
-
Therefore
~I
9m
I
~j
~Vg
j
-- .-
1 mA, ~j /j = 100 and ~Vg = 0.5 V t hen: 9m
=
200 mA/V 3
In this case, a transconductance of 200 mA/V requires a channel thickness of tcond = 530 nm. Modern IC technologies allow the realisation of much thinner channels. From the above example, it is clear that field-effect devices can only be realised with semiconductor materials. Aware of this fact, Lilienfeld used copper sulphide as a semiconductor in 1930. Germanium was used during the early fifties. Until 1960, however, usable MOS transistors could not be manufactured. Unlike the transistor channel , which comprised a manufactured thin layer, the channel in these inversion-layer transistors is a thin conductive layer, which is realised electrically. The breakthrough for the fast development of MOS transistors came with advances in planar silicon technology and the accompanying research into the physical phenomena in the semiconductor surface. Generally, circuits are integrated in silicon because widely-accepted military specifications can be met with this material. These specifications require products to function correctly at a maximum operating temperature of 125°C. The maximum operating temperature of germanium is only 70°C, while that of silicon is 150°C. A comparison of a few other germanium (Ge) and silicon (Si) material constants is presented below:
Material constant Melting point [0C] Breakdown field [V/ f.lm] Relative expansion coeff. [0C]-l Er
Max . operating temp. [0C]
1.3
Germanium 937 8 5.8 x 10- 6 16.8 70
Silicon 1415 30 2.5 X 10- 6 11.7 150
The inversion-layer MOS transistor
A schematic drawing of the inversion-layer nMOS transistor, or simply 'nMOSt' , is shown in figure 1.2, which is used to explain its structure and operation. The two n" areas in the p-type substrate are called the source and drain. The gate electrode is situated above the p area between them. This electrode is either a metal plate, e.g., aluminium or molybdenum, a heavily doped and thus low-ohmic polycrystalline silicon layer, or a combination of both. Normally, the source and drain areas are also heavily doped to minimise series resistance. The resistance R 4
of a 10/-lm long and 2/-lm wide track is 120 • R o , where R o is the sheet resistance of the track material. The sheet resistance of the source and drain areas usually ranges from 3 to 100 njD with doping levels upto 5.10 19 to 2.10 20 atoms per em", The dope concentration in the p-type substrate is approximately 1014 _10 16 atoms per cm'', while the channel dope (by threshold adjustment implantation, etc.) is between 1017 _10 18 atoms per ern". A p-channel transistor differs from the above n-channel type in that it contains a p+ source and drain in an n-type substrate. gate
ourcc
drain
(bu lk) ub trate
Figure 1.2: Cross-section of an inversion-layer nMOS transistor Characteristic parameters of a MOS transistor are indicated in figure 1.2. These include the width Wand length L of the channel and the thickness tax of the insulating oxide which separates the gate and channel. In modern CMOS VLSI circuits, the minimum values of Wand L range from 40 nm to 120 nm and tax ~ 1.2 nm - 2.5 nm . Continuous development will reduce these values in the future . The depth of the source and drain junctions varies from 50 nm to 200 nm. The energy band theory and its application to the MOS transistor are briefly summarised below. An understanding of this summary is a pre-requisite for a detailed discussion of the behaviour of the MOS transistor. The structure of a free silicon atom is shown in figure 1.3. This atom comprises a nucleus , an inner shell and an outer shell. The nucleus contains 14 protons and 14 neutrons while the shells contain 14 electrons. Ten of the electrons are in the inner shell and four are in the outer shell. The positive charge of the protons and the negative charge of the electrons compensate each other to produce an atom with a net neutral charge . 5
nuclcu ,,--- -- ........
,{
,,/
••••-. ~ inner hell
>\
I I
(10 electron )
\ \
I
I
:
:
outer hell
:
(4 electron )
\
I
\
,.'
:
\
\"
-
_-_ .-' -4
Figure 1.3: Th e struct ure of a free silicon atom The elect rons in an at om may possess cert ain energy levels. These energy levels are grouped into energy bands, which are separated by energy gaps. An energy gap represents impossible levels of elect ron energy. The energy bands that apply to the electrons in an at om's outer shell are valence and conduction band s. Figure 1.4 shows these bands and the energy gap for a typical solid mat erial. The valence elect rons determine the physical and chemical prop erti es of a materi al. conduction band electron
} forbidden gap
energy
valence band
Figure 1.4: Schematic representation of electron energy bands in a typical solid material
The four elect rons in the outer shell of a silicon at om are in the mat erial 's valence band . Figure 1.5 shows the bonds that t hese electrons form with neighbouring atoms to yield a silicon crystal.
6
Figure 1.5: Silicon crystal The electrons in a conductor can easily go from the valence band to the conduction band. Therefore, the conduction and valence bands in a conductor partly overlap, as shown in figure 1.6a. In an insulator, however, none of the valence electrons can reach the conduction band. Figure 1.6b shows the large band gap generally associated with insulators. A semiconductor lies somewhere between a conductor and an insulator. The associated small band gap is shown in figure 1.6c. Valence electrons may acquire sufficient thermal energy to reach the conduction band and therefore leave an equal number of positively-charged ions, or 'holes', in the valence band. This produces a limited conduction mechanism in semiconductors.
7
(a)
(b)
(c)
;>.
~ (l) l::::
•
(l)
l:::: 0
t:to)
(l)
~
•• •• ••
• ••• •• •
•• •• •• •
Figure 1.6: En ergy bands of a conductor, an insulator and an intrin sic sem iconductor Semiconducto r materials are located in group IV of this syst em. The introduction of an element from group III or V in a semiconduct or crystal produces an 'acce ptor' or a 'donor' atom. This semiconductor doping process dr am ati cally cha nges t he crystal properties. The following t abl e shows t he location of semiconductor materials in the periodic syste m of elements .
III (Acceptors) Boron Aluminium Gallium Indium
Group IV Carbon Silicon Germ anium Stannic (tin)
V (Donors) Nitrogen Phosphorous Arsenic Stibnite
The presence of a group III at om in a silicon crystal lattice is considered first . The situation for boron (B) is illustrated in figur e 1.7a. Boron has one elect ron less than silicon and cannot therefore provid e an elect ron required for a bond with one of its four neighbouring silicon atoms. The hole in the resulting p-type semiconductor is a willing 'acceptor' for an elect ron from an alte rnative sour ce. This hole can be removed relatively easily with the ionisation energy of approximate ly 0.045 eV shown in the energy band diagram of figur e 1.7a. 8
Similar reasoning applies when a group V ato m, such as phosph orus (P) , is present in the silicon lattice. This sit uation is illustrat ed in figure 1.7c. The ext ra electron in the phosph orus atom cannot be accommodated in t he regular bondin g st ructure of the silicon lat tice. It is therefore easy to remove t his 'donor' electron in t he resulting n-type semiconductor. The mere 0.037 eV ionisation energy required is much lower t han t he 1.11 eV band gap energy of silicon. Figur e 1.7b shows the energy band diagram of an intrinsic silicon lattice, which contains no donor or acceptor 'impurity' atoms. The energy level indicat ed by Er in figure 1.7 is called t he Fermi level. An elect ron with t his energy has an equal probability of location in the valence band and the conduct ion band. This probability is exact ly 0.5. The Fermi level of an intrinsic semiconduct or is ofte n referr ed to as the intrinsic Fermi level Ej . The Fermi level Ef in a p-type semiconductor is sit uated near the valence band E v , while it is close to the conduct ion band E c in an n-type semiconductor . T he ab ove theory concerning t he different ty pes of semiconductors and their respective energy band diagrams will now be used to explain the behaviour of t he MOS tra nsistor. This explanation is preceded by a description of the st ructure and operation of t he MOS capacitor.
9
•
p-typc cmiconductor
intrinsic cmiconductor
/cxtm electron
n-type semiconductor
,
· B 0.045 c
EC}
1 Ef .1 ••••••• E\, E
(a)
•
•
•
• (b)
C
p , • • • • • E; 0.037 cV -', - - - - e,
• (c)
Figure 1.7: Energy band diagrams for p-type, intrinsic, and n-type semiconductor materials
10
1.3.1
The Metal-Oxide-Semiconductor (MOS) capacitor
F igure 1.8 shows a cross-sect ion of a basic MOS capac itor. This struc t ure is identic al to a MOS t ransistor exce pt t hat t he source and drain diffusion regions are om itted.
Vg < 0
------- j-------
Vg>O
++++++++++++++ ---=,...---=,....,
lox -+--,..--_ _
__ ~
C??
e+
~
e+ e+
J??
depletion layer
(b) Depletion
(a) Accumu lation
e: fixed negati
c charge carriers (acceptor atom.) + : mobile po itivc charge carriers (free hole) - : mobile negative charge carriers (free electron)
Fi gure 1.8: Cross-section of a MOS struct ure witho ut source and drain areas. Th ere is a capacitance between the gate and substrate. T he p-typ e substrate is mad e wit h an acceptor dop e mat erial , e.g., boron. The substrate is assumed to behave as a normal conductor and contains many free holes. The situation which occurs when t he p-typ e substrate is grounded and a negative voltage is applied t o t he gate elect ro de is shown in figure 1.8a . The negativ e cha rge on the gate is compe nsated by an equal but positive charge in t he substrate . This is accomplished by positively charged holes which accumulate at the SiSi0 2 int erface. These holes are the majority charge carriers in the subst rate. This 'acc um ulation' pr ocess continues until t he positive charge at t he subst rate sur face equals the negative cha rge on t he gate electro de . Ex tra holes are supplied t hrough t he ground contact to t he substrate. The resul t ing accumulation ca pac itor ca n be viewed as an ideal par allel plate capacitor. A different sit uation occurs when t he potenti al on t he gate elect rode is made positi ve wit h respect to t he gro unded substrate. This sit uation is shown in t he cross-section of figure 1.8b. T he pos itive charge which 11
is present on the gate must be counter-balanced by a negative charge at the Si-Si0 2 interface in the substrate. Free positively-charged holes are pushed away from the substrate surface to yield a negatively-charged depletion layer. This 'depletion ' process stops when the negative charge of the depletion layer equals the positive charge on the gate electrode. Clearly, the thickness td of the depletion layer in the equilibrium situation is proportional to the gate voltage. It is important to realise that a depletion layer only contains a fixed charge, i.e., ions fixed in the solid state lattice, and no mobile charge carriers. Various energy band diagrams are used to explain the behaviour of the inversion layer MOS transistor. To provide a better understanding of these diagrams, Poisson's law is first applied to the different regions of the MOS capacitor. These regions include the gate, the Si02 insulator, the depletion layer in silicon and the p-type silicon substrate. Poisson's law is used to investigate the charge distribution Q(z), the electric field E(z) and the electric potential¢(z) in these regions as a function of the distance z from the Si-Si02 interface. In its one dimensional form, Poisson's law is formulated as follows: p
(1.2)
E
where
p
electrical potential at position z; distance from the Si - Si02 interface; space charge ;
E
dielectric constant.
¢(z) z
The situation in which no space charge is present is considered first. This is almost true in the Si02 insulator, in which case p = O. Integration of formula (1.2) once gives the electric field: C1 = integration constant.
Integration of formula (1.2) twice gives the electric potential in Si02:
The electric field in the insulator is thus constant and the electric potential is a linear function of the distance z from the Si-Si0 2 interface.
12
Next, the situation in which a constant space charge is present is considered. This is assumed to be true in the depletion layer, whose width is Wo . In this case:
p where q and NA
-q·NA
the charge of an electron the total number of fixed ions in the depletion layer of thickness td.
Integrating formula (1.2) once gives the electric field: q ·NA
E(z) = - - · z + C1 E
Integrating formula (1.2) twice gives the electric potential in the depletion layer:
Therefore, the electric field in a depletion layer with constant space charge is a linear function of z, while the electric potential is a square function of z. The space charge in a depletion layer is only constant when the dope of the substrate has a constant value at all distances z from the Si-Si02 interface. In practice, the space-charge profile is related to the dope profile which exists in the substrate. The gate and the substrate region outside the depletion layer are assumed to behave as ideal conductors. The electric potentials in these regions are therefore constant and their electric fields are zero. The above results of the application of Poisson's law to the MOS capacitor are illustrated in figure 1.9. Discontinuities in the diagrams are caused by differences between the dielectric constant of silicon and silicon dioxide . The electric charge, the electric field and potential are zero in the grounded substrate outside the depletion region. The observation that the electric potential is a square function of z in the depletion layer is particularly important.
13
+Q Vg
-Q
e e e ee e eee e -
0--
II
i02
- lox
0
IVD
..
~ z
E (z)
t
this drop is caused by the
r====:fference in
Es,,, and Es; ~ z
¢(z)
t linear
square
~z
F ig ure 1.9: The sections of a MOS capacitor and the associated charge distribution Q(z), electric field E(z) and electric potential ¢ (z )
14
1.3.2
The inversion-layer MOS transistor
Figure 1.10 shows a cross-section of an nMOS transistor wit h OV on all of its te rminals. T he figure also cont ains t he associated energy band diag ram. Metal
Oxide
_ emiconductor (p-typc)
Ec
------- ---- .::~~:~~~ ~~!~~~~~~~~ ~~
r= Fermi potential
Ev
e :fixed charge (acceptor-atom) + - : mobile charge (hole or electron , re pectively) Figure 1.10: Cross-section of a MOS transistor with Vgs =Vds =V';;b=OV and th e associated energy band diagram It is assumed that t he presence of t he gate does not affect t he dist ribu t ion of holes and electrons in t he semiconduct or. With the exception of t he depletion areas around the n" areas , t he ent ire p-sub strate is assumed to be homogeneous and devoid of an electric field (E = 0). There is no charge on t he gate and no surface charge in t he silicon. Generally,
15
the electron energies at the Fermi levels of the different materials in the structure will differ. Their work functions (i.e., the energy required to remove an electron from the Fermi level to vacuum) will also differ. When the voltage between the gate and source is zero (Vgs = 0) and the metal gate is short circuited to the semiconductor, electrons will flow from the metal to the semiconductor or vice versa until a voltage potential is built up between the two materials. This voltage potential counter-balances the difference in their work functions . The Fermi levels in the metal and the semiconductor are then aligned. Therefore, there will be an electrostatic potential difference between the gate and substrate which will cause the energy bands to bend. The 'flat-band condition' exists when there is no band-bending at the metalsemiconductor interface. The 'flat-band voltage' Vfb is the gate voltage required to produce the flat-band condition. It is the difference between the work functions of the metal (1)M) and the semiconductor (1)5) , i.e., Vfb = 1>MS = 1>M - 1>5· Since equilibrium holds, the Fermi level in the semiconductor remains constant regardless of the value of the gate voltage. A negative charge is induced in the semiconductor surface when a small positive voltage is applied to the gate, while the source, drain and substrate are at OV, see also figure 1.11. The negative charge is caused by holes being pushed away from the insulator interface. The negatively charged acceptor atoms that are left behind form a negative space charge, i.e., a depletion layer. The thickness of this depletion layer is determined by the potential Vc at the silicon surface . The gate voltage Vgs now consists of two parts: a. The voltage across the oxide Vg
-
Vc ;
b. The voltage across the depletion layer
~.
The capacitance between the gate and substrate now consists of the series connection of the oxide capacitance Cox and the depletion-layer capacitance Cd. The term VT in figure 1.11 represents the threshold voltage of the transistor. This is the gate voltage at which the band-bending at the silicon surface is exactly 21>[. At this band bending, the electron concentration at the semiconductor surface becomes equal to the hole concentration in the bulk. This situation is called (strong) inversion, and the layer of free electrons created at the surface is called an inversion
16
layer. For t he pr esent , VT is ass umed to be positi ve for an inversion-l ayer nMOS transisto r. T his ass um ption is confirmed lat er in t he text .
o
(a)
- - - - - - -- z
b
Figur e 1.11: Cross-section of a MOS transistor with O< Vgs< VT and Vds =~b =O V and its corresponding energy band diagram If t he gate volt age is fur ther increase d (Vgs > VT) , t hen the band-b ending at t he silicon surface will be lar ger than 2¢f . This sit uation is illustrat ed in figure 1.12. A compa rison of figure 1.12 and figur e 1.7c reveals t ha t t he energy band at t he silicon sur face correspon ds to an n-typ e semiconductor.
17
M
0
~---
silicon urface
(a)
depletion layer inver ion layer
mobile charge
b
Figur e 1.12: Cross-section of a MOS transistor with Vgs> VT (VT> O) and
Vds=~b=O
V and its corresponding energy band diagram
Deep in t he subst rate , however , the energy band corresponds to a ptyp e semiconductor. A very narrow n-typ e layer has t herefore been crea ted at the surface of a p-typ e silicon subst rate. In addit ion t o the negative acceptor atoms alrea dy present , t his inversion layer contains elect rons which act as mobile negative cha rge car riers. Conduction in the n-typ e inversion layer is mainly perform ed by these electrons, which are minority carriers in th e p-type substrat e. The inversion layer forms a conduct ing channel between the t ra nsisto r' s source and dr ain . No cur rent flows in t his cha nnel if there is no voltage difference between the dr ain and source terminals, i.e., Ids = 0 A if Vd s = 0 V. The numb er of elect rons in the cha nnel can be cont rolled by t he gate-source volt age
Vgs .
18
Assuming that Vgs > VT, the effects of increasing Vds from 0 V are divided into the following regions: 1. 0 < Vds
< Vgs - VT.
This is called the linear or triode region of the MOS transistor's operating characteristic.
2. Vds = Vgs - VT. At this point , a transition takes place from the linear to the socalled saturation region. 3. Vds > Vgs - VT. This is the saturation region of the MOS transistor's operating characteristic. The three regions are discussed separately on the following pages .
19
The linear region Figure 1.13 shows the situation in the linear region, in which a current Ids (which flows from drain to source) causes a voltage difference in the channel. The surface potential under the gate decreases from Vds in the drain to 0 V in the source. The maximum potential difference between the gate and channel is at the source . Therefore, the strongest inversion and the highest concentration of electrons in the inversion layer occur adjacent to the source. The maximum potential difference between the channel and substrate is at the drain. The depletion layer is therefore thickest here. In the linear region, the drain current Ids increases with increasing Vds for a constant V gs.
in er ion layer 0.5 nm to 5 nm thick
g ~ ._~-~
0/
-e-e e--- -e-ee e-ee e -
----- -----{2
e- e e- " e e-----------..' e+ ----------e+ ",-e -e e -ee e+ e e e+ - e+ ~~-----e-----e+ e+ e+ p- e e+ e+ e e b Figure 1.13: Cross-section ofa transistor operating in th e linear (triode) region
20
The transition region An increase in Vds, with Vgs constant, decreases the voltage difference between the gate and channel at the drain. The inversion layer disappears at the drain when the voltage difference between the gate and channel equals the threshold voltage VT. The channel end then coincides with the drain-substrate junction. This situation occurs when Vds = Vgs - VT , and is shown in figure 1.14.
IVg . > vT >ol
___.1.£
_
e
e
e
b Figure 1.14: Situation during transition from triode to saturation region, i.e., Vds=Vgs- VT
21
The saturation region
T he cha nnel end no longer coincides with the drain when tha n Vgs - VT. Thi s sit uation is shown in figure 1.15.
8
-0---- - --
Vds
is larger
8
8 8 8 8 8 8 8 8 8 8,,·------__ 8 ------------,,' ----- 8 8 - - 8 8+ + --------: 8 8 8 8 8 + -----___ 8 8 8 p- 8 + 8 +----(;+--8+--b Figure 1.15: Sit uation in the sat uration region, i.e., Vd s > Vgs
-
VT
The volt age Vx at the end point x of t he inversion layer equals Vgs - VT. Therefore, VT is t he voltage difference between the gate and channel at position x . If t his pinch-off point is considered to be t he virt ual drain of t he tra nsistor, then Ids is determin ed by the voltage Vx = Vgs - VT. In ot her words, the dr ain current in the saturation region equals the drain current at the tra nsit ion point between t he linear and sat uration regions. The value of t he sat uration current is clearly proportional to Vgs . Electrons are emitted from t he inversion layer into the deplet ion layer at t he pinch-off point. Th ese electrons will be at t racted and collected by the dr ain because Vds > Vx , which builds a large electric field across t he very narrow pinch-off region. Figure 1.16 shows the Ids = f (Vds) characteristic for various gate volt ages. If Vds = 0 V, t hen Ids = 0 A. If Vds is less than Vgs - VT, then t he t ra nsistor operates in the tri ode region and the current Ids displays an almost linear relationship with Vds ' Curr ent Ids increases to its saturation value when Vds = Vgs - VT. Fur th er increases of Vds above 22
VT no longer cause increases in I ds ' T he transit ion between t he t riode and saturation regions is characte rised by t he cur ve Vds = Vgs - VT. Vgs -
Rout = finite (real transistor)
•
3
saturation region
linear or triode region 1-,"
./ ._.-.-.-.-.-.-.- I •
,~
Vgs = IV
....Rout = infinite ...
(ideal current source)
•• ••
/~VdS = Vgs -Vr
.'
o- F - - , . - - - , . - - - , . - - - , . - - - , . - - - - ' o 0.25V O.5V O.75V 1V 1.25V -
Vds[V]
Figure 1.16: T he Ids=! (Vds) characteristic Eor various values oEVgs
1.4
Derivation of simple MOS formulae
The inversion layer nMOS t ransisto r shown in figur e 1.17 has a width W perp endi cular to t he plane of t he page and an oxide capacitance Cox per unit area . A commonly-used unit for Cox is fF/ J-lm 2 , where 1 fF = 10- 15 F.
23
inver ion layer depIction layer
x =o
x =L
x
Figure 1.17: Charges in a MOS transistor operating in th e linear region Based on the law for conservation of charge , the following equality must hold at any position x between the source and drain: (1.3) The components in this equation are charges per unit area, specified as follows:
Qg = t he gate charge [C/m 2 ] ; Qox= primarily a small fixed charge which in practice always appears to be present in the thin gate oxide [C/m 2 ] ; Qn = the mobile charge in the inversion layer [C/m 2 ] ; 2 Qd = the fixed charge in the depletion layer [C/m ] . For gate voltages larger than VT , the inversion layer shields the depletion layer from the gate. The charge in the depletion layer can then be considered constant: (1.4) The threshold voltage VT is assumed to be constant. The potential in the channel at a position x is V( x). With Qg = Cox[Vgs - V( x)] and substituting (1.4) into (1.3) yields: Qn = -Cox[Vgs - VT 24
-
V(x)]
The total mobile charge dQm in a sect ion of the channel with lengt h dx is defined as: dQm = Qn . W . dx = - W . Cox [Vgs - VT - V (x)] . dx dQ m
- W· Cox [Vgs - VT - V (x)]
~ =
=}
The drain current
(1.5)
(1.6)
is expressed as:
Ids
I
_ dQm _ dQm dx ili - d;- . dt
ds -
(1.7)
where d~xm is defined in equat ion (1.6) and ~~ is the velocity v at which th e charge Qm moves from t he source to t he drain region. This is t he velocity of t he electrons in the inversion layer and is expressed as:
v
dV (x) dx
= Mn . E = - Mn . - -
(1.8)
where E is t he electric field st rengt h and Mn repr esents t he electron mobility in t he inversion layer. The mobility repr esents the ease in which charge carriers move within a semiconducto r. In practice, the effective mobility appears to be less t han one third of t he electron mobility in t he subst rate (see section 2.3). Combining equations (1.6), (1.7) and (1.8) yields: Ids =
dV(x) Mn . Cox ' W · [Vgs - VT - V( x)] . - dx
(1.9)
Substituting (30 = Mn . Cox yields: Ids '
dx = (30 ' W . [Vgs - VT - V (x )] . dV (x)
(1.10)
Integrating the left-hand side from 0 to L and t he right-hand side from o to Vd s yields:
(1.11) 25
Equation (1.11) has a maximum value when Vds = Vgs - VT. In this case, the current Ids is expressed as:
Ids =
1 W 2. L . (30 . (Vgs -
VT)
2
(1.12)
If Vgs = VT then Ids = 0 A. This clearly agrees with the earlier assumption that VT is positive for an inversion-layer nMOS transistor. The term (3 is usually used to represent ~ . (30. This factor is called the transistor gain factor and depends on geometry. The gain term (30 is a process parameter which depends on such things as the oxide thickness t ox : (30
EOE
ox = f-Ln . Cox = f-Ln . -t -
(1.13)
ox
The unit of measurement for both (3 and (30 is A/y2. However, f-LA/y2 and mA/y2 are the most commonly-used units. For an n-channel MOS transistor, (30 varies from 360 f-LA/y2 to 750 f-LA/y2 for oxide thicknesses of 3.2 nm and 1.6 nm, respectively. Note that these values for (30 resemble the zero-field mobility in the substrate. The effective mobility in the channel, and so the effective gain factor, is much lower due to several second order effects as discussed in chapter 2. According to equation (1.11), Ids would reach a maximum value and then decrease for increasing Vds - In the discussion concerning figures 1.15 and 1.16, however, it was stated that the current remains constant for an increasing Vds once Vds > Vgs - VT. The transistor has two operating regions which are characterised by corresponding expressions for Ids' These regions and their Ids expressions are defined as follows:
1. The linear or triode region. 0 < Vds < Vgs - VT. (1.14) 2. The saturation region. Vds :?: Vgs - VT. (1.15) According to equation (1.15), Ids is independent of Vds in the saturation region. The output impedance dVds/dIds should then be infinite and the transistor should behave like an ideal current source . In practice,
26
however, MOS transistors show a finite output impedance which is dependent on geomet ry. This is explained in chapte r 2. Figure 1.16 shows both the ideal (theoreti cal) and t he real current-voltage characterist ics of a transistor with a t hreshold voltage VT = 0.25 V. The I ds = !(Vds)IVgs= constant curves in figure 1.16 are joined by the dotted curve Vd s= V gs- VT at the points where equat ion (1.14) yields maximum values for I ds' This curve divides the Ids- V ds plane into two regions: 1. Left of the dot ted curve: t he triode or linear region, which defined by equation (1.14);
IS
2. Right of the dotted curve: t he saturation region, which is defined by equation (1.15).
1.5
The back-bias effect (back-gate effect, body effect) and the effect of forward-bias
The simple MOS formulae derived in section 1.4 appear to be reasonably satisfactory in most cases. The very important back-bias effect is, however , not included in t hese formul ae. Thi s effect accounts for the modul ation of the threshold volt age by t he subst rate bias and the subsequent effects on the drain current . During normal operation (when V gs > VT and Vd s > V gs - V T) a depletion layer is formed , as shown in figure 1.15. However , t he t hickness of the depletion region und er t he channel increases when a negat ive back-bias voltage (l!,;b) is applied to the bulk (b) with respect to the source . This is caused by t he increased reverse-bias voltage across the fictive cha nnel-substra te junction. The increased depletion layer requires additional charge . T he cha nnel charge therefore decreases if V gs is held constant . T he channel conduct ivity can only be maint ained if Vgs is increased. The t hreshold voltage is t herefore relat ed to the back-bias voltage l!,;b. This dependence is expressed as follows:
+ K J~b + 2(jJf Vx + K J2"1X Vx
The term s in t hese formulae are as follows:
Vx
= pro cess-related constant threshold voltage t erm ; 27
(1.16) (1.17)
VT O = VTIV';,b=OY ; K = process parameter equal to -ri-y'2NAQfOfsi ; vox
also known as the 'body factor' or K-factor; NA = substrate (bulk) dope concentration; V';,b = source-bulk (back-bias) voltage ; 2
VTl
Vx + K JV';,lb + 2
VT 2
Vx + K JV';,2b + 2
If the output is 'high' (~ O.7V) , the source-bulk voltages of T 1 and T2 are V';,l b = V';,s - Vbb = 0 V and V';,2 b = Vout - Vb b = 0.7 V, respectively. The source-bulk voltage can therefore cause the threshold voltage VT 2 of the upper transistor to be considerably larger than the threshold voltage VTl of the lower transistor. Vdd=
1.2V
Figure 1.18: nMOS-inverter with enhancement load Figure 1.19 shows the influence of the back-bias effect on different transistor characteristics. Formula (1.16) clearly shows that the threshold voltage VT increases with an increasing back-gate voltage v;,b. For a constant Vgs , the drain-source current therefore decreases for an increasing V';,b. This is illustrated in figure 1.19b. 28
(a)
(b)
Vsb = 0 0.5 I 1.5V Vds = 1.2V
I
Vsb ._------0 V . _ - - - - - - O.5V ._-------1 V
I o
o
0.25 0.5 0.75 1 1.25
-
. _ - - - - - - - 1.5V
Vgs[V]
0.25 0.5 0.75 1 1.25
-
Vds[V]
Figure 1.19:
Back-bias effect on MOS transistor characteristics: (a) Ids= !(Vgs)IVds=const (b) Ids= !(Vds)IVgs=const
Figure 1.20 shows the dependence of VT on ~b' The starting-point of this graph is determined by VTO in equation (1.17) while its curve depends on the K -factor.
0.50
VT[V]
I
_
-------_._------------_.
## ##
0.25
o Figure 1.20: VT=! ("Veb) : Threshold voltage as a function ofsource-bulk voltage
The back-bias effect must be accurately treated when dimensioning MOS circuits. The most important reasons for using a back-bias voltage are as follows: • Normally, the term Vx in equations (1.16) and (1.17) spreads more than the K-factor. The influence of the K-factor on the threshold voltage is larger when a back-bias voltage is applied. This results in a more stable threshold voltage. 29
• The depletion layer around the source and drain junctions of the MOS transistor becomes thicker as a result of the increased reverse voltage across these p-n junctions. This reduces the parasitic capacitances of the source and drain. • Negative voltage pulses which may occur in dynamic MOS logic circuits may forward-bias the p-n diode between the substrate and a source or drain. Application of a negative voltage to the substrate virtually removes this possibility. • Because an additional back-bias voltage increases the VT , it reduces the subthreshold leakage current. This usage is described in chapter 8. Next to the back-bias effect, there also exists a forward-bias effect. This effect is sometimes used to reduce the threshold voltage in order to improve the performance of certain logic or memory cores on a chip. In such cases, the source-to-substrate junction is put in forward bias, but with a voltage level below the junction voltage , which is equal to about 0.6V. The MOS transistor formulae are summarised as follows:
- linear region - saturation region (1.18)
where and
1.6
Factors which characterise the behaviour of the MOS transistor
The previously-discussed current-voltage characteristics represent the relationship between a transistor's current (Ids) and its various applied 30
voltages (Vgs, Vds and v'b)' A number of important par ameters which are frequently used to describe t he behaviour of a t ra nsisto r are explained below. The transconductance grn describes the relat ionship between t he change aIds in the t ra nsistor current caused by a change avgs in t he gate voltage: (1.19) Referring to figure 1.16, it is clear t hat the value of grn depends on the t ransistor's operating region: Linear region : grn Saturation region : grnsat.
(3 . Vds
(1.20)
(3. (Vgs - VT)
(1.21)
Another par amet er t hat characterises conduct ion in a t ra nsistor is its output conductance. In the t ransistor's linear operating region, this conductance (which is also called t he channel conductance) is defined as: dIds ) { gds = ( dVds = f3 (Vgs - VT )
-
f3 Vds}
(1.22)
If Vds is small, t hen: (1.23) For an ideal MOS t rans istor operating in t he saturation region, we have ~~~ = O. The trans istor current is t hen independent of Vds ' The out put resistance is t herefore infinit e and t he t ra nsistor acts as an ideal current source. In pr actice, however , the MOS t ransistor always has a finit e out put resist ance and its curre nt remains dependent on Vds' This is illustrat ed in figure 1.16 and is t reated in sect ion 2.4. We will now briefly discuss two ot her figure-of-merits, which represent t he frequency response of a MOS transistor. If we ignore parasit ic effects, the average transit t ime T of a carrier across t he cha nnel L of an int rinsic device, operating in its linear region is equal to:
£ T= -
pE
£2 = -
-
p Vdd
(1.24)
and T= -
t.
Vsat 31
(1.25)
when the device is in velocity saturation (see chapter 2) and where equals the saturation speed of the carriers in the channel. In most tradition al CMOS technologies Vsat ~ 10- 11 cm/s, so t hat T ~ 10 ps for a transistor with a channel length L = 100 nm . This leads to t he so-called cut-off (or t hreshold) frequency iT at which the device can fill and empty t he channel as a respon se to an ac signal: Vsat
iT -
-
1 _
gm
Vsat _
- - - - --
27fT
27f L
27fCgs
(1.26)
with the average carrier velocity in the channel equal to gm / Cox ~ gm /Cgs' In saturation it is clear that Vaverage = Vsat . Scaling thus leads to a reduction of t he transit tim e and to an increase of the transconductance and cut-off frequency.
1. 7
Different types of MOS transistors
1. The previous discussions are all related to n-channel MOS transistors. The subst rate material of these nMOS t ra nsist ors is p-typ e and the drain and gate voltages are positive with respect t o t he source during normal operation. The substrate is the most negative electrode of an nMOS tra nsistor. 2. P-chann el MOS transistors are produced on an n-type subst rate. The voltages at t he gate and drain of th ese pMOS transistors are negative with respect to th e source during normal operation. The subst rate is the most positive electrode. Generally, nMOS circuits are fast er than those with pMOS tr ansist ors. The power-delay (TD) product of a logic gate is th e product of its delay T and dissipation D . The T D products of nMOS logic gates are lower than tho se of pMOS logic gat es. This is becaus e of the difference between the mobility of elect rons and holes. Electron mobility is a factor of about 2.5 t imes higher than hole mobility in both the bulk silicon and inversion layers of t he respective devices. Figure 2.1 illustrat es thi s relationship , which is expressed as follows: I-ln
~
2.5 . I-lp
The following relationship t hen follows from equation (1.13): 32
f30 n ;:::; 2.5 . f30 p An nMOS transistor therefore conducts approximately two and a half times as much current as a pMOS transistor of equal dimensions and with equal absolute voltages. Advanced CMOS technologies, today, apply different channel-stress and crystal-orientation techniques to improve the transistor drive currents and which also drives the performance of the pMOSts closer to that of the nMOSts . These are discussed in chapter 3. Figure 1.21 shows a schematic overview of transistors which are distinguished on the basis of threshold voltage VT. This distinction applies to both pMOS and nMOS transistors and results in th e following types: • Enhancement or normally-off transistors: No current flows through an enhancement transistor when Vgs = O. VT > a for an nMOS enhancement t ransist or and VT < a for a pMOS enhancement transistor. • Depletion or normally-on transistors: Current flows through a depletion transistor when Vgs = O. VT < a for an nMOS depletion transistor and VT > a for a pMOS depletion transistor.
33
n-channel
Ids enhancement type
t
p-channel
Vds > 0
Ids
t
ornormally off
depletion type ornormally on
Figure 1.21: Schema tic overview of th e different types of MOS transistors
1.8
Parasitic MOS transistors
MOS (V)LSI circuits comprise many closely-packed t ra nsistors. This leads to t he presence of parasitic MOS t ra nsist ors, as illust rated in figure 1.22.
34
metal track gate I
gate 3
thick field oxide (= 100 - 500nm)
thin gate-oxide (Inm - 5nm)
Figure 1.22: Example of a parasitic MOS transistor Transistors T 1 and T 2 are separated by the field oxide. Parasitic MaS transistor T3 is formed by a metal interconnection track on the field oxide and the n" areas of transistors T 1 and T2. This field oxide is thick in comparison with the gate oxide, which ensures that the threshold voltage VTpar of transistor T3 is larger than the threshold voltages of transistors T 1 and T 2. The field strength at the silicon surface in T 3 is therefore lower than in T 1 and T 2. Transistor T 3 will never conduct if its gate voltage never exceeds VTpar ' Many MaS production processes use an extra diffusion or ion implantation to artificially increase the threshold voltage VT par of parasitic transistors. For this purpose, boron is used to create a p-type layer beneath the thick oxide in processes that use p--type substrates. This makes it much more difficult to create an n-type inversion layer in these areas. Processes that use n" -type substrates use phosphorus to increase IVTpar I· The terms channel stopper implant is used to refer to these boron and phosphorous implantations. Note: Parasitic MaS transistors also appear in bipolar circuits. The absolute value of parasitic threshold voltages is always higher in n-type substrates than in p-type substrates. This is one of the reasons why planar Ie technologies were mainly developed on n-epi layers .
35
1.9
MOS transistor symbols standard symbols
r___---- -------~A~- ----- ------~,
(a)
d
J g---1 ! l
s
s
(b)
(c)
(d)
d
b
g---1 ~b
s
s
s
(e)
(f)
(g)
Figure 1.23: Various transistor symbols Figure 1.23 shows various symbols used in literature to represent MOS t ra nsistors. Their meanings are as follows: a) The inward pointing arrow indicates th at the tra nsistor is n-channel and the broken line between s and d indicat es that it is an enhancement transistor. b) The solid line from s to d indicates t hat this n-channel transistor is a depletion device. c) The outward pointing arrow indicates that the transistor is p-channel and t he broken line between sand d indicates that it is an enhancement transisto r. d) The solid line from s to d indicates that thi s p-chann el transistor is a depletion device. e) This symbo l for an n-channel enhancement tra nsistor is analogous to t he npn transistor symbol.
36
f) This p-channel transistor is by definition not necessarily an enhancement type. g) This general symbol represents a MOS transistor of any type. Adaptations of the above symbols are also used. MOS symbols must therefore be interpreted with caution. The following rules are generally applied : 1. A transistor symbol with a broken line between its source and drain is always an enhancement or normally-off type; 2. Arrows indicate the forward directions of the substrate-channel 'junctions'. The symbols in figure 1.24 are used throughout this book.
nMOS enhancement transistor
nMOS depletion transistor
pMOS enhancement transistor
Figure 1.24: Transistor symbols used throughout this book
37
1.10
Capacitances in MOS structures
Figure 1.25 illust rates t he MOS capacitance, whose value depen ds on such t hings as Vg and t he frequency at which it varies. Section 1.3.1 describ es t he MOS capacitance and presents a qualit at ive discussion of its relat ed charges, fields and volt ages. Figure 1.26 shows a plot of t he total capacitance C, between t he gate and ground terminals as a funct ion of t heir voltage difference. Vg
_ _1_ _ .-
..t,fox
p-
Figure 1.25: T he MOS capacitance The var ious regions of the C-V curve in figure 1.26 are explained as follows: 1. Vg « VT for a p-type substrate; Vg » VT for an n-type substrate. Here, the surface pot enti al
riers in t he p-typ e subst rate will form a surface layer of holes. T his accumulation layer is t hin in comparison with the oxide t hickness and exists as long as Vg is much smaller t han VT. Now, t he silicon behaves like a met al plate, and t he MOS capacitance is equal to the oxide capacitance Cox. Deviat ions only appear at very high frequencies (> 1 GHz), where t he dielectric relaxation time TR is impo rt ant . For t he 10ncm silicon, TR :=::::10 ps (=10- 11 s). 2. Vg :=: : VT , thus O. A voltage change ~ V at the gate causes a cha nge ~Q in t he charge at the edge of t he depletion layer. In fact , the tot al capacitance is now determin ed by t he series connect ion of t he gate capacitance and t he depletion layer capacitance. T he capaci tance t herefore decreases.
38
3. Vg » VT for a p-type substrate; Vg « VT for an n-type subst rate. Now, ¢s is highly positive and an inversion layer is created. This
layer is t hin compared to the oxide thickness. At low frequencies « 100 kHz), t he capacitance will again be equal to the oxide capacitance Cox . However, the inversion layer for a p-type subst rate consists of electrons that are supplied and absorbed by the substrate. T his relies on the process of thermal generation and recombination of minorities, i.e., t he electrons. With a constant temperature, the speed of t he generation/recombination process is limited. Thi s accounts for t he lower capacitance shown in figure 1.26 at higher frequencies (> 1 MHz). At t hese high frequencies, the capacitance Ct will be about equal to the series connect ion of t he gate capacitance and t he depletion layer capacitance.
Vg
~ / channel depletion layer C ox
at low - - - - - -- frequencie
1==== . . .
C
i
o o o o o
Cmin
-_ ..-
--_
- ..
-
o o o o o o o
...
1 0_._._'-'_._._._._._'-'_._'_0_._._' ._0_01-
·,, ··, o
o
at high freque ncie
. o
---_ . ~---~ ._-----~
accumu lation dep letion
inversion
Figure 1.26: Capacitance behaviour of a MOS struct ure As discussed, t he MOS capacitance can be considered as a series connection of two capacitances: t he oxide capacitance Cox between t he gate and the silicon surface and a capacitance Cs between t he silicon surface and the subst rate interior. T his is explained below. 39
The voltage Vg can be expressed as follows: Vg =
Vox
+ ¢ms + ¢s
(1.27)
The law for conservation of charge yields the following equat ion: (1.28) where: Vox = voltage across the oxide between gate and silicon surfaces; ¢ms = cont act potenti al between gate and substrat e; ¢s = surface potenti al of the silicon with respect t o t he subst rate interior ; Qg = charge on the gate; Q ox = charge in the oxide; Qn = charge in t he inversion layer; Qd = charge in the depletion layer.
The following expression for a change ~ Vg in gate volt age can be derived from equat ion (1.27): ,6.Vg =
,6.Vox
+ ,6.¢s
(¢ms is constant , t hus ~ ¢ms = 0) (1.29)
Substituting Qn+ Qd= Q s in equat ion (1.28) yields: ,6.Qg
=
-,6.Qox - ,6.Qs
(1.30)
If Q ox is considered constant, t hen: ,6.Qg = -,6.Qs
(1.31)
Equ ations (1.29) and (1.31) yield the following expressions: ,6.Vg ,6.Qg
,6. Vox ,6.Qg
~ ¢s
~ Vox
,6.Qg
,6.Qg
,6.¢s
- - = - - + - - = -- - -
so,
where:
so;
LWi
= C; = the total capacitance of t he MOS st ruct ure; = Cox = oxide capacitance;
-
~~:
= Cs = capacitance between t he silicon surface and the
semiconduct or interior (depletion layer capacitance).
40
Ct can now be expressed as follows: 1
1 _1
Ct = ( - +-)
c,
Cox
(1.32)
Capacitance Os is responsible for the drop in the G - V cur ve. The value of Gs is determined by the subst rate doping concentration and the potential difference across the depletion layer. The minimum value Gmin in t he C - V curve is also det ermined by Cox . A small er Cox leads to a larger -ri- and a smaller Cmin . Cmin can be as low as O.lGox. v ox The C - V curve is often used during MOS manufacturing processes to get a quick impression of the value of VT. Figur e 1.27 shows a MOS capacitance with an additional n+ area, which causes significant changes in the capacitance behaviour. The st ruct ure is in fact equivalent to a MOS transistor without a dr ain or to a MOS t ra nsist or with an exte rnal short circuit between its dr ain and sourc e. This structure is genera lly called a MOS capacita nce or a MOS varactor. Dynamic MOS circuits , in particular, use t his device very often .
pb Figur e 1.27: MOS capacitance with source and/or drain area Whil e Vgs < VT , there is no inversion layer in a MOS capacitan ce, and the behaviour of the gat e capacitance is unchanged. However , an inversion layer is crea ted when Vgs > VT . The elect rons in this inversion layer are supplied by the n" area instead of by therm al gener ation/recombination processes of minorities in the substrate. This n+ area can generate and absorb electrons at very high frequencies (> 1 GHz). Therefore, 41
will now equal C ox und er all norm al opera t ing conditions. In this case, Ct represents the capacitance between t he gat e and source, i.e., C t = C gs = Cox(L + b.L) . W. The dependence of the capacitance C gs on the applied volt age Vgs is summarised as follows: Ct
• When Vgs < VT , there is no inversion layer . Here, the value of C gs is determined by the channel width W and the gate overlap !:lL on the source/dra in area : C gs = !:lL . W · Cox ' • When Vgs > VT , there is an inversion layer. Here, C gs is determined by the channel length L : C gs = (L + !:lL) . W . Cox' The above non-linear behaviour of Cgs = f (Vgs ) is shown in figure 1.28.
u~
(L + M) . W · Cox
I
~
M· W · Cox 1 - - - - 0 /
o Figure 1.28: Non-linear behaviour of a MOS capacitance Note: There is no inversion layer when Vgs < VT. Figure 1.26 shows how the gate-subst rate capacitance then behaves.
Figure 1.29 shows t he lar ge numb er of capacitances in a real MOS t ra nsistor. These capacitances, which are largely non-linear , are defined as follows: C db , Csb
C gdo, C gso : Cgd , C gs
drain-substrat e and source-subst rate capacitances, which are non-linearly dependent on Vdb and ~b, respectively. gate-drain and gate-source capacitances, which are voltage-independent . gate-dra in and gate-source capacitances (via t he inversion layer) , which are non-lin early dependent on Vgs , 42
C gb
:
Vgd and Vgb . gate-subst rate capacitance, which is non-linearly dependent on Vgb .
p" ub trate
(a)
g
s
d
(b)
b Figure 1.29: Capacita nces in a MO S transistor
43
The values of the C db and C sb diode capacitances in figur e 1.29 are expressed as follows:
C(V) _ Co - (1 + ~)l /m
(1.33)
J
where:
= capacitance when V =0; Vj = junction voltage (0.6 V to 0.9 V);
Co
m = grading fact or , 2 ::; m ::; 3: m = 2 for an abru pt junction and m = 3 for a linear junction. Terms Cgdo and C gso represent gate overlap capacitances that are det ermined by t he t ransistor width, the length of the overla p on t he drain and source ar eas, and t he t hickness of the gate oxide. These capacitances are clearl y voltage-ind epend ent. The gate-substrate capacitance Cgb is only imp ortant if Vgs« VT . Now, C gb is often expressed as C gb::::::: (0.12 to 0.2) . W . L . Cox. The inversion layer shields t he subst rate from t he gate and Cgb= O when Vgs~ VT· Terms Cgd and C gs represent gate-drain and gate-source capacitances, respectively, which are present via the inversion layer (figure 1.28). T he values of t hese capacitances depend st rongly on t he bias voltage on the te rmina ls of t he MOS t ra nsisto r. The following cases are distinguished: Case a Vgs< VT ; no inversion layer, thus Cgd=Cgs= O. Case b Vgs> VT and Vds =O. For reasons of symmet ry, Cgs =Cgd = ~ . W . L . Cox' Case c Vgs> VT and Vds > Vd sat (Vdsat = Vgs - VT). T he transist or is in saturat ion and t here is no inversion layer at the dr ain: Cgd = O and C gs = ~ . W · L . Cox. This expression for Cgs is derived below. Case d Vgs> VT and 0 < Vds< Vd sa t ' In t his case, a linear interpolation between t he values in cases b and c closely corresponds to the actual values, which are shown in figur e 1.30.
44
\.) C gIOI =
1
2/3 CgtOI
W· L·
Cox
-----------~-~--:--~ - ww--~~
1/2 Cg10 l
Figure 1.30: Cgs and Cgd depend ence on Vds for Vgs> VT The above expression in case c for the gate-source capacitance Cgs of a saturat ed MOS transistor is explained with t he aid of figure 1.31. This figure shows a cross-sect ion of a MOS tran sistor biased in the saturat ed region . The cha nnel does not reach the drain ar ea , but stops at a point where the channel potential is exac t ly Vgs - VT.
p- sub trate ---~ x
x =o
x =L
Figure 1.31: Cross-section of a saturat ed MOS transistor. Cgs = ~ . W . L . Cox '
C gd
= 0 and
Equation (1.5) leads to the following expression for the charg e dQ in a cha nnel section of length dx at position x :
dQ(x) = Qn ' W · dx = -W . Cox[Vgs - VT - V( x)] . dx 45
(1.34)
The following expression for dx is derived from equation (1.9):
dx =
j.tn . Cox'
W . [Vgs - VT - V(x)] . dV(x) Ids
(1.35)
Combining equations (1.34) and (1.35) yields the following expression for dQ(x) :
dQ(x) =
j.tn ·
Cox
2 .
W
2 .
[Vgs - VT - V(x)F . dV(x) Ids
(1.36)
Equation (1.15) yields the following expression for the drain current Ids in a saturated MOS transistor:
Ids =
f3 ( "2' Vgs -
)2 VT =
j.tn . Cox
2
.
W L . (Vgs -
VT
)2
(1.37)
Substituting equation (1.37) in equation (1.36) yields:
Integrating equation (1.38) from the source to the imaginary drain gives:
Q =
=?
Q =
rVgS-VT
lv.
2
"3' W
Cox'
[Vgs - VT - V(x)F . dV(x) (Vgs - VT ) 2
W · L·
2 ·
. L . Cox' (Vgs - VT)
(1.39)
The gate-source capacitance Cgs can be found by differentiating Q in equation (1.39) with respect to Vgs:
dQ
C gs
2
= dVgs ="3' W· L · Cox
(1.40)
The Cgs of a saturated MOS transistor is therefore only two thirds of the total value, while the gate-drain capacitance is zero.
46
In summary: Most capacitances in a MOS transistor are non-linearly dependent on the terminal voltages. For each capacitance, these dependencies are as follows : 1. The diode capacitances Cdb and Csb: C(V)
= (1+f')l/m' where Vj ;: ;:; 0.6 . .. 0.9 V and 2 ~ m ~ 3. J
2. Figure 1.28 shows the voltage dependence of gate-channel capacitances Cgd and Cgs when the drain and source are short circuited, as is the case in a MOS capacitance. Figure 1.30 shows the voltage dependence of Cgd and Cgs when the drain and source are at different voltages, i.e., during normal transistor operation. 3. The gate-substrate capacitance Cgb is 0 when Vgs> VT and Cgb= 0.2· W· L· Cox if Vgs< VT . 4. The overlap capacitances Cgdo and Cgso are the only capacitances which are not dependent on the terminal voltages .
47
1.11
Conclusions
The basic principles of the operation of the MaS transistor can be explained in different ways. The fairly simple approach adopted in this chapter should provide a good fundamental understanding of this operation. The current-voltage characteristics presented are derived by means of the simplest mathematical expressions for MaS transistor behaviour. Second-order and parasitic effects are not essential to an understanding of the basic principles of MaS transistor operation. They have therefore been neglected in this chapter. However, these effects should be included in accurate descriptions of MaS transistors and are therefore discussed in chapter 2. Most of these effects are includ ed in the MaS transistor models used by commonly-used compact MaS models in circuit simulation programs.
48
1.12
References
General basic physics [1] R.S.C. Cobbold, 'Theory and applications of field effect transistors' , Wiley, New York [2] S.M. Sze, 'Semiconductor Devices: Physics and Technology', 2nd Edition (Illustrated) , John Wiley & Sons Inc., September 2001 [3] Y.P. Tsividis , 'Operation and modelling of the MOS transistor', WCB Mc Graw-Hill, Boston 1999 [4] C. Kittel, 'Int roduction to Solid State Physics (7t h edition)', Wiley, 1996, New York MOS capacitances [5] E.W . Greenwich, 'An Analytical Model for the gate Capacity of Small-Geometry MOS structures' , IEEE Transactions on Electron Devices, ED-30, pp 1838-1839, 1983 [6] J .J .Paulos , D.A. Antoniadis, and Y.P. Tsividis , 'Measurement of Intrinsic Capacitances of MOS Transistors', ISSCC Digest of technical papers, pp 238-239, 1982 [7] D.E. Ward and R.W . Dutton, 'A Charge-Oriented Model for MOS Transistor Capacitances', IEEE Journal of Solid-State Circuits, pp 703-707, 1978 [8] H. Kogure, et al., 'Analysis of CMOS ADC Non-linear Input Capacitance', IEICE Trans . Electron. , Vol. E85-C, No.5, May 2002
49
1.13
Exercises
Note: 24>f=1 V throughout t hese exercises. 1. What happens to t he depletion layer in figure 1.12 when the subst rate (b) is connected to a negati ve voltage (~ -1 V) instead of
ground? What effect does this have on t he threshold voltage VT ?
(r
2. Current I ds in a t ra nsistor = 2) is 100/-LA when its gate-source volt age V is 0.8 V . The curre nt is 324/-LA when V = 1.2 V .
WIL = r - l 1.2 V g
: i~-----'beI
s
a) Which t ra nsistor operating regions (linear or saturated) do t hese values of V correspond t o? b) Calculate
f30 and
VT for the given tra nsistor.
3. Given:
d
g
I..---f?fb
+
1.2 V
s
a) What typ e is t he t ransistor shown? b) Calculat e I ds when this t ransisto r has t he same f3 as t he t ra nsistor in exercise 2 and VT= -1 V.
50
4. Given:
-------~
d
If this is an n-type enhancement MOS transistor and the current Ids> 0, explain the following: a) This transistor is always in its saturation region. b) This connection is often called a MOS diode. 5. For this exercise , the threshold voltage VT is 0.25 V. There is no thermal generation of electron/hole pairs.
Vg
___1 _ p: ub trate
b
a) The above structure exists when the source and drain areas of an nMOS transistor are excluded. Copy this structure and include the possible depletion and inversion layers for the following values of Vg : -0.6 V, 0.1 V, 0.6 V and 1.2 V. b) An n+ area is now added to the structure in exercise 5a.
51
Vg
r
Vs
p- ub tratc
b
Repeat exercise 5a for
~
= 0 V and for
Vs
= 0.5 V.
c) The sub strate of the st ructure in exercise 5b is connecte d to a negative voltage: Vbb=-l V. What happ ens to the depletion and inversion layers if ~ = 0 V and Vg = 0.5 V? d) A second n" area is added to the st ructure of exercise 5b to yield the following struct ure.
p- ubs tratc b
Repeat exercise 5a for
~
= 0 V and
Vd
= 0.8 V.
e) In pr acti ce, there are t hermally-generated electron hole pairs in t he silicon subs trat e. The resulting free electrons in t he deplet ion layer move in t he opposite directi on to the applied exte rnal elect ric field. Draw the direction of movement of the t hermally-generated electrons and holes for Vg=1.2 V in t he struct ure of exercise 5a. If this sit uat ion cont inues for a longer period, a new equilibrium is reached and the elect rons and holes accumulate in the structure. Draw thi s sit uat ion.
52
------eF--- Vdd
d
g 6. The following values apply in the figure shown: Vdd=1.2Y , ,6=lmA/V 2 , Vx=-l Y, Vbb = - l Y .
s +
_ _ _--.1._ _
V ss
a) What type is the transistor and why? b) Calculate and draw the graph Ids=!(Vds) for K=Oy 1/ 2 and Vds=O, 0.2, 0.4, 0.6, 0.8, 1.0 and 1.2 Y. c) Repeat b) for K =0.2 y 1/ 2 . d) Assuming K =0 .2 y 1/ 2 , calculate the output impedance of the transistor for Vds=50 mV and for Vds=0.6 Y. (Note: the drain remains at 1.2 Y).
- - - , . - - - - Vdd
w
- = 0.12/0.06
L
7. The following values apply
for the circuit shown: Vd d = 1.2Y, Vbb = -1 Y, V';;s = 0 Y, K =0.2 y 1/ 2 , 2 ,60 = 400 p,A/y , VX L = -1 Y and VX o = 0.2Y.
: --1
load transistor
"----+---0 Vout
Vin
:
W -=4
: L
~- Vss
driver transistor
a) Calculate Vout for Vin=1.2Y. b) Determine the transconductance of both MOS transistors for this situation. c) What value does Vout reach when Vin=O.lY? d) The same low output level must be maintained when the load transistor is replaced by an enhancement-type transistor of the 53
same size and with its gate at ~jd' Does this require a driver transistor with the same and with a smaller or a larger channel width W? Explain your answer.
If
8. The aspect ratio of this transistor is W/ L = 200nm/50nm. Results of measurements on it are summarised in the following table:
d g
I~b I
~b[V]
Ids [tt A ]
40
Vgs = IV 360
10
-
Vgs = 0.5V 0 1.25
a) Determine Vx , K and
!3o
1
8
for this transistor.
b) Calculate and draw the graph VT=f(~b) for at least five ~b values (0 V <~b<2 V). 9. Define an expression for the transconductance with respect to the substrate voltage ~b when the transconductance with respect to
the normal gate voltage is defined as gm = :~: .
10. Assume that we build a decoupling capacitor between
Vdd and using an nMOS transistor with a gate-oxide thickness t ox 1.6nm.
~s
a) Draw how this nMOS transistor is connected between the Vdd and ~s lines to form this capacitor. b) What would be its capacitance value per unit area? c) Assuming a pMOS transistor operates fully complementary to an nMOSt, how would you connect such a pMOSt as an additional capacitor in the same circuit as in a).
54
11. The following values apply in the figure shown: both nMOS transistors are identical, Vdd = 1 Y, VT = 0.3 Y when k = 0 y 1 / 2.
~v
~ a) With what type of device could you compare T 1? b) With what type of device could you compare T2? c) What would be the voltage Va when k = 0 y 1/ 2? d) What would be the voltage Va when k = 0.2 yl /2? e) If one of the ~s connections of T 2 would be left open (floating) , what would be the result in terms of operation of the device T 2 and of the operation of the total circuit?
55
Chapter 2
Geometrical-, physical- and field-scaling impact on MOS transistor behaviour 2.1
Introduction
The simple formulae derived in sect ions 1.4 and 1.5 account for the firstord er effects which influence t he behaviour of MOS t ransistors. Unt il t he mid-seventies , formulae (1.18) appeared quite adequate for predicting the performan ce of MOS circuits. However , t hese tr ansistor formulae ignore severa l physical and geomet rical effects which significant ly degrade t he behaviour of MOS transistors. The results are therefore considera bly more optimi sti c tha n the actual performance observed in MOS circuits. T he deviation becomes more significant as MOS tra nsist or sizes decrease in VLSI circuits. This chapter contains a brief overvi ew of t he most import ant effect s, in nanomet er CMOS technologies, which degrade the performance of MOS devices. The cha pte r concludes with a det ailed discussion on transist or leakage mechanisms.
57
2.2
The zero field mobility
As discussed in chapte r 1, th e MOS transist or current is heavily det ermined by t he gain factor f3 of the transistor :
f3 =
w . f30
-
L
w . /-L . Cox
= -
(2.1)
L
where Wand L represent t he transist or channel width and length respectively, Cox represents t he gate oxide capacitance per unit of area and /-L represents the act ual mobility of t he carriers in t he channel. Thi s mobility can be quite different from th e zero-field or subst rate mobility /-Lo, which depends on the doping concent ration in the subst rate . Figure 2.1 shows zero-field elect ron and hole mobilities in silicon at room temp erature as a function of the doping concent rat ion. [cm 2 /Vs]
1500
~
1250
[cm 2 / s)
~Ino
35
cI ctron
~
0 0
l"'l
30 E <:> 'u 25 Eu
~
0
13. 1000
g
0
u
:.E 750
20
0
c 0
' Vi
E
500
15 @
!lpo
~
10
hole '
250
5
10 15
1016
10 17
lOl l!
1019
1020
1021
[atom /cm 3]
Figure 2.1: Zero-field carrier mobility and diffusion coeflicient as a function of doping concent ration in silicon at room tem perat ure
For a channel dopin g concentration of 1017 atoms/crrr' , the mobility of electrons (/-Lno) is about three tim es that of holes (/-Lpo), in t he absence of an elect ric field. This is t he major reason that the Ion current (which is the saturation current when Vgs = Vdd) of an nMOS transistor is abo ut 58
two to four times higher than t he Ion of an equally sized pMOS transistor, depending on the technology node. It also depends on the transistor st ress engineering and crystal orientation. However , severa l other effects dramatic ally reduce the mobility of t he carriers in the channel. These are discussed in section 2.3.
2.3
Carrier mobility reduction
During norm al transisto r operation, electrical fields are applied in both t he lat eral (horizont al) and transversal (vertical) directions, which influence t he mobility of the carri ers in t he channel. Moreover , when the chip temp erature is increased, eit her by an increase of the ambient t emperat ure or by t he chip's own dissipat ion, thi s will have a negative effect on t he carrier mobility and thus on t he (3 of each t ransisto r.
2.3.1
Vertical and lateral field carrier mobility reduction
During norm al operat ion, the effect ive mobility /-l of t he carriers in the transistor channel is degraded by t he mechani sms indicat ed in figure 2.2. These include the vertical electric field E z , the lat eral elect ric field Ex and the carrier velocity v .
gate
L
p- sub trate Figure 2.2: Compo nents which affect carrier m obility in MOS transistors
When the vertical electric field E; is high, t he minority carriers in an n-chann el device are st rongly attracted to the silicon surface, where they 59
rebound. The resulting 'surface scattering' is indicated by the dashed lines in figure 2.2. This causes a reduction of the recombination time and of carrier mobility f-l with increasing E z . In [1], some experimental results are presented with respect to the vertical field carrier mobility degradation. The vertical electric field depends on the gate voltage and on the substrate voltage . The relationship between these voltages and the mobility can be expressed as follows: f-lo
f-l
= 1 + 01 (Vgs - VT )
+ 02( V~b + 2
(2.2)
where, f-lo represents the zero-field substrate mobility,
=
f-l
(2.3)
where (2.4) Substituting equation (2.4) into equation (2.3) yields: f-l
where
=
f-lo
1 + 03 , Vds 1 03 = L · ».:
(2.5) (2.6)
The above effects are included in the following expression for carrier mobility: f-lo
f-l
= (1 + 01 (Vgs - VT) + 02(V~b + 2
(2.7)
At high gate voltages, the vertical field influence (represented by t he voltage terms containing Vgs and ~b) may reduce the transistor current 60
by about 50 %. The lateral field influence may be of the same order of magnitude. Note that this lateral field close to the source dominates the drain-source current. At a level of about 1 V/ J-Lm , this lat eral field also reduces t he electron mobility in t he chann el of an nMOS transistor by almost 50 %. Thus, t he total field-dependent mobility reduction can amount to a fact or four . The act ual mobility is equal to the substrate mobility when E z = O. Some t ransist or models include the series resist ance of t he source (Rs ) and the drain (Rd) in t he surface scattering factor 01 and in the velocity-saturation factor 03 . Moreover , these resist ances are weakly dependent on t he te rminal voltages and are therefore included in the device equat ions. Their influence can be incorporat ed in equat ion (2.7) by replacing 01 and 03 by 0/ and 03 ' , respectively, where
(2.8) and
(2.9) Because these resistances are in series with the transistor terminals, t hey have a reducin g effect on t he transistor current. Due to the ultra-short channel lengths, to day, t ransistors show elect ric fields that exceed 10 V/ J-Lm. Because E Xsa t is smaller for electrons t han for holes, t he performance of nMOS t ransistors (conduct ion by electrons) is more degraded by velocity saturation t han t hat of pMOS transistors (conduct ion by holes). Figure 2.3 shows the carr ier velocity v as a functi on of the electric field E x in t he channel. The criti cal field E X s at to reach velocity satura t ion depends on the doping level and is about 3 V/ J-Lm for electrons and about 10 V/ J-Lm for holes. In fact , holes may reach a saturation velocity comparable to the Vsat of electrons.
61
Temp = 300 K
I 0 5 L..-....I..4......... ..L.U.J.I.l...---J.......J....l..l..:..u..:.l....-...l......L-:..J..U.lJJ....---l......I....I..L.J:.u.lJ 0 .0 I
O. I
10
100
Electric Field [ V/~lIl1 ]
Figure 2.3: Carrier velocity as a function of the lateral electric field in the channel
This carrier velocity is defined by:
(2.10) So, in t he derivation of t he current expression (1.12), we can replace 11' Vdsl L by v. Part icularly in 90 nm CMOS processes and beyond, most car riers in t he channel t ravel at a maximum sat uration velocity Vsat . This would lead to a sat uration current equal to: I
-
ds -
VsatCox W
2
. (Vdd
-
V; ) T
(2.11)
This reduces the channel length's influence on the current, which is one of the reasons that the transistor's drive current has shown negligible increase over the last couple of t echnology generations. This is not expected to change for future generat ions; for almost all CMOS pro cesses from 180 nm to 45 nm , t he I on for t he nMOS and pMOS transistors remain approximate ly equal to 650 mA l 11 m and 270 mAl 11 m , respectively. As a result , the effective gain factor f30eff of a t ransistor with minimum drawn gate length (Ldrawn) almost remains at a constant value, which is close to or somewhat below 100 I1A/V 2 . Figure 2.4 shows t his gain factor as a function of the drawn channel length for various technology generations [2]. LSTP and LOP refer to a low standby power and a low operating power, respectively.
62
450
...... 180nmLSTP -+- 65 nm L TP .... 45nmLSTP --- 32 nm LOP
~
~2-
400
.
300
1::
350
~ 250 200
I
.
150
-...;w improvement of 13
50
-
•
~
100
IT
0 0.0
0.1
0.2
0.3
-----}~ ~
0.4
0.5
Ldrav..,. [11m]
Figure 2.4: The effective gain factor versus the drawn channel length for various technology generations {2} It also shows that ,BOeff improves dramatically with increasing Ldrawn ' For example an increas e of Ldrawn in the 45 nm CMOS node from minimum length to about 100 nm , will double the value of ,BOeff. For digital circuits this channel length increase is certainly not an appropriate solution for performance increase, because it also increases the chip area. However, if we compare a minimum drawn transistor (Ldrawn = 0.18 f.Lm) in 0.18 f.Lm technology with a transistor with the same Ldrawn = 0.18 f.Lm in 32 nm technology, the performance improvement is close to a factor of four. So, for analog circuits, which usually take a small portion of the chip area on a mixed analog/digital design , a larger channel length serves two goals. First it improves the transconductance (gm rv ,BOeff( Vgs - VT)) and , secondly, it redu ces the threshold voltage variation, which improves the transistor matching properties and enables a better performance prediction. These variability-related topics are discussed in chapter 9. Chapter 3 presents a few mobility enhancement techniques which will improve the performance of both the digital and analog circuits in advanced and future nanometer CMOS lCs.
2.3 .2
Stress-induced carrier mobility effects
The mechanical stress induced by shallow-trench isolation (STI) has an increasing effect on the carrier mobility of the nMOS and pMOS devices.
63
It degrades the mobility of nMOS devices, while it slight ly improves it of t he pMOS. Chapte r 3 discusses mobility enhancement techniques t o improve transistor device performance in advanced CMOS technologies.
Channel length modulation
2.4
The ideal Ids vs Vds characte ristics illustrat ed in figure 1.16 do not show the influence of Vds on Ids in t he saturation region. In practice, an increase in Vds in t he sat uration region causes an increase in Ids' This phenomenon is particularly obvious in short-channel devices and is caused by channel length modulation . The distribution of carriers in an nMOS t ra nsistor operating in the sat uration region (Vds > Vdssat = Vgs- VT ) is illustrated in figure 2.5. T he operation of t he basic MOS t ransist or in this region is discussed in section 1.3. Clearly, the end of the inversion layer (which is called the virtual dr ain) does not reach t he act ual drain . T he effective channel length t herefore equals L - LlLcLM. JIgs > JI,. > 0
-8-
8
8
8- I1
8
8
1
8+ 8+
8
8+ 8+
8 8
8+ 8+
p-
8+
8 8
8 + 8+
b
Figure 2.5: A MOS transistor in the sat uration region (Vd s > Vgs - VT ) The saturat ion curre nt specified in equation (1.15) must be changed to account for the effect ive channel length. T he modified expression is as
64
shown in equation (2.12). Idssat
=L
w
-
b..L
f30
CLM
. -2 . (Vgs - VT)
2
(2.12)
where b..L is the lengt h of the depletion region at the silicon surface between the inversion layer and the drain. In the above expression, th e total field-dependent mobility degradation, as discussed before, is not included. The voltage Vds - Vdssat across t his 'pinch-off' region modulates b..LCLM. Thi s effect can be modelled by:
b..LZ u vI = a In (1 + Vds ~;dssat )
(2.13)
where a and Vp are constants , which may vary with the tra nsisto r geomet ry. The expression clearly shows t he relation between b..LCLM and t he amount of Vds voltage above Vdssat . T he above discussions show t hat t he additional cont ribut ion to t he drain current of a MOS tra nsistor operating in t he saturation region is proportional to Vds - Vdssat . This effect is somet imes approximated by t he following modified current expression: (2.14) Where I dsQ is the tra nsistor current when t he channel length modul ation is ignored, and oX is a semi-empirical channel length modul ation par amete r, whose reciprocal value (1/ oX ) is analogous to t he BJ T Early voltage . The effect of this channel length modul ation on t he I ds = !(Vds) characte rist ics is shown in figur e 2.6, where t he extrapolation of t he curves in t he saturation region would all intersect t he x-axis closely to the point
it».
65
1.5 [V] 2
1.25 1.0 0.75 0.5 O~-----i---+---+
o
0.5 -----~~~
1.5 Vds [V]
Figure 2.6: Effect of channel length mo dulation on the MOS transistor characteristic
Channel-lengt h modulation is an undesired effect, which is par ticularl y an issue for analog design. Because channel-lengt h modulation is a shortchannel effect which rapidly decreases with longer cha nnels, analog designs ty pically require larger t han minimum t ransist or channel lengths to improve t he performance and operating margins.
2 .5
Short- and narrow-channel effects
T he electrical behaviour of a MOS t ra nsistor is primar ily det ermi ned by its gain factor {3, its t hreshold voltage VT and its body fact or K. Generally, t he values of these parameters are largely depe ndent on t he width W and length L of a tra nsistor. T he influence of t hese dependencies increases as t ra nsistor dimensions decrease. T hese small-channel effects, which are discussed below, are part icularly significant in deep-subrnicron and nanometer MOS processes.
2.5.1
Short-channel effects
The cross-secti on present ed in figure 2.7 is used to explain short-channel effects.
66
- - - - -L - - - -..
Depletion boundary
Figure 2.7: Cross-section of a short-channel transistor, showing several depletion areas that affect each other
Even in the absence of a gate voltage, the regions under the gate close to the source and drain are inherently depleted of majority carriers, i.e., holes and electrons in nMOS and pMOS transistors, respectively. In a short-channel transistor, the distance between these depletion regions is small. The creation of a complete depletion area under the gate therefore requires a relatively small gate voltage . In other words, the threshold voltage is reduced. This is a typical two-dimensional effect, which can be reduced by shallow source and drain diffusions. However, the associated smaller diffusion edge radii cause a higher electric field near the drain edge in the channel when Vds> Vgs>VT. One way to overcome this problem is to reduce the supply voltage. This short-channel effect on the threshold voltage occurs at shorter gate lengths and causes threshold voltage roll-off, see figure 2.8).
67
0.60
~ 0
00
.s
"0 ;. "0
til
~ ..c
reverse short-c hanne l effec t
0.50
0040 0.30
"0
..c
/
0.20
hort-ehannel effect (thre hold voltage roll-on)
f-
0. 10 0.00 0. 1
1.0
10.0 [prn]
Gate Length
Figure 2.8: Short-channel and reverse short-channel effect on the threshold voltage VT of an nMOS transistor
The use of shallow source and drain exte nsions (see figure 3.39), with less doping than the real source and drain implants, in combination with local higher doped cha nnel regions (so-called halo or po cket implants) suppresses the depletion-layer width in the channel and cont ributes to a reduction of the short-channel effect (SeE). The implant is optimised for tra nsist ors with t he smallest chann el lengths in a given pro cess. These transistors will have the nomin al threshold voltage while t ra nsistors with longer channels will have higher threshold voltages. A second effect that depends on t he channel length is the reverse short-channel effect (RSCE). In convent ional CMOS devices, thi s effect, which involves increasing t hreshold voltages VT with decreasing gate length, is caused by a lateral non-uniform channel dopin g induced by locally enhanced diffusion. As describ ed before, current devices use so-called halo implants to suppress short -channel effects. Figure 2.9 shows a possible dope profile in a device with halos. In devices with relatively long channels, these halos occupy a smaller region of the channel. When the channel becomes shorte r, these halos get closer to one anot her and will also cause VT rollup. In 180 nm CMOS t echnologies and beyond , these halos int entionally cause roll-up and suppress t he onset of roll-off.
68
ource
drain
L
Figure 2.9: Potential doping profile in the channel of a MOS device including the halos
2.5 .2
Narrow-channel effect
Also, t he width of an act ive device influences t he t hreshold volt age. Th e depletion layer extends under t he edges of t he gat e, where t he gate electrode crosses t he field oxide. With a LOCOS ty pe of field isolation, see figure 2.10, t his effect is primarily caused by t he encroachment of the cha nnel stop dopant at th e edge of t he field isolati on.
LO 0
t----l~'---__ ,
'---------------------~---
channel top implant
"r---.......----~
depletion layer
p" ub tratc
Figure 2.10: Cross-section of a narrow-channel transistor showing the distribution of electric field lines under the gate Th e addit ional depletion region charge has to be compensated by an 69
additional gate voltage. This results in an increase of the threshold voltage at reduced width of the device. The encroachment of channel stop dopant is especially pronounced for a conventional diffused well technology. The channel stop dopants are implanted prior to the hightemperature LOCOS oxidation and cause a large shift in VT. In a retrograde implanted well process, the field oxidation is performed prior to the well implants and less encroachment of dopant atoms occurs under the gate edge. However, the threshold voltage is still increased as a result of the bird's beak and two-dimensional spreading of the field lines at the edge. Figure 2.11 shows this narrow-channel effect, together with the influence of the channel width on the threshold voltage in a Shallow-Trench Isolation (see chapter 3) scheme. In contrast to the conventional narrowwidth effect, the threshold voltage is even decreased at very narrow channel widths of around 0.2 /-lm. This Inverse Narrow- Width Effect (INWE) is attributed to a sharp corner at the top of the shallow-trench isolation. The fringing field at this corner results in an increased electrical field strength and reduces the threshold voltage. Also, the quality of the oxide used to fill the trench is not as good as the thermally grown LOCOS field oxide. A positive fixed oxide charge is present in the oxide and, in nMOS devices, it contributes to the decreased threshold voltage. This contribution of the fixed oxide charge is less severe than the fringing field compound and depends also on the deposition method used to fill the trench.
70
,.......,
LOCOS + Conventional well
100
>
S ......... II)
-'"
01l
'0 > "0
'0
50 LOCOS + Retrograde well
0
~
'" ~
~
Eo-<
STI + Retrograde well
-50 -100 0.0
0.5
1.0
1.5
2.0
2.5
Active area width [11m]
Figure 2.11: Shift of threshold voltage of nMOS devices as a function of the active area width for different well technology and field isolation schemes
2.6
Temperature influence on carrier mobility and threshold voltage
An increase in t he operating tem perat ure of a MOS t ra nsistor affects its behaviour in two different ways: 1. T he mobility of t he majority carriers, e.g., electrons in an nMOS
t ransistor, in t he channel decreases. Consequently, t he transisto r gain factor (30 also decreases. It s temperature dependence is expressed as follows [3]: 298 (30 (Temp) = (30 (298 K ) · ( T em p
)3/2
(2.15)
T he exponent 3/2 in this expression is more applicable to th e electron mobility. For holes thi s exponent is closer to 1. PMOS t ransisto r currents are therefore less tempera t ure dependent than those of nMOS transistors. 2. The threshold volt age VT of both nMOS and pMOS t ra nsist ors decreases slightly. T he magnitude of t he influence of tempera ture 71
change on threshold voltage variation LlVT depends on the substrate doping level. A variation of -0.7 mV C is quite typical.
r
Both effects have different consequences for the speed of an IC. This speed is determined by the speed T of a logic gate, which is defined as:
CV
T
=I
CV
= 2 . ,6(Vgs
_
VT)2
(2.16)
In conventional CMOS processes the overall circuit performance reduces with increasing temperatures, because its effect on the mobility reduction in the transistor current was traditionally larger than the effect on the reduction of the threshold voltage. This was one of the reasons to keep high-speed processors cool, by using a fan. Also worst-case corner simulations were usually done at high temperatures. However, today's CMOS technologies offer several different threshold voltages to support both high-speed and low-leakage applications. For general-purpose and high-speed processes, VT is relatively low and a further reduction with 0.7mV has less influence on this speed than the reduction in the,6. For low-leakage processes, with a relatively large VT , both effects partly compensate each other, because of the increasing competition between mobility and threshold voltage, so that there is a reduced influence on the speed. At a certain supply voltage the above two mechanisms fully cancel each others contribution to the transistor current, such that the circuit speed has no longer a relation with the temperature. This is the so-called zero-temperature-coeflicient (ZTC) voltage [4,5] . This reducing temperature dependence, which is expected to continue with further scaling of the supply voltage, has serious consequences for the static timing analysis, as it may invalidate the approach of defining PVT (process, voltage and temperature) corners , by independently varying voltage and temperature [6] . Figure 2.12 shows the frequency response of a highVT ring oscillator as a function of the supply voltage , for different operating temperatures.
rC
72
0.14 0.12
..........
0.10
:r: ~ 0.08 ...... >. Co)
5 0.06 ::l 0'"
U
tot
0.04
ZTCvol tagc
0.02 0.00
L
0.8
0.9
1.1
1.2
1.3
1.4
I.S
Voltage [V ]
Figur e 2.12: Rin g osci11ator frequency response as a function of the supply voltage at different temperatures
Above the ZTC volt age of 1.1 V, which is close to th e nomin al supply voltage of 1.2 V in this t echnology, t he frequency redu ces with increasing te mperature, while below thi s volt age t he effect is opposit e. For t he same ring oscillator fabricated with a standard VT , this ZTC is reduced to 0.95 V. As a result of this var ying temperature behaviour, the worst-case and best- case corners for simulat ion need t o be reconsidered, since for modern CMOS technologies a higher te mpera t ure not automatically corresponds t o a lower performan ce! For t he 45 nm technology nod e and beyond , the temp erature effect will diminish further , because of an increas ing compensat ion of t he f3 and VT cont ribut ions to t he transistor current [7] . ZTC also has consequences for certain failure analysis methods (see chapt er 10) that use local heating to det ect cha nges in circuit behaviour , because t hese cha nges will become smaller and less visible in mod ern technologies.
73
2.7
MOS transistor leakage mechanisms
Due to the continuous scaling of the physical MOS device dimensions, such as channel length and gate-oxide thickness, and increasing doping levels to suppress short-channel effects (SeEs), MOS devices will increasingly drift away from an ideal switching behaviour. As a result , an increasing number of leakage mechanisms is influencing their performance , particularly during off-state. Figure 2.13 shows the major contributions to the total transistor leakage current.
d
I) = Sub-threshold Leakage (inc!. Drain-Induced Barrier Lowering (DIBL» 1 = Gate Oxide Tunneling 2
1 3 = Reverse Bias Junction Leakage
1 4 = Gate-Induced Barrier Drain Leakage (GIDL) 1 5 = Impact Ionisation current
Figure 2.13: Leakage mechanisms in nanometer CMOS technologies The reduction of the supply voltage (Vdd) for a series of technology generations has caused the threshold voltage (VT) to reduce accordingly, in order to achieve sufficient performance increase. A lower VT leads to a larger off-current: a larger drain-to-source leakage current when the gate-to-source voltage is zero: subthreshold leakage current. The reduction of the gate-oxide thickness below 2.5 nm has resulted in charge carriers tunnelling through the oxide from the channel to the gate or vice versa and causes a gate-leakage current. This tunnelling is not caused by the field only, but mainly by the penetration of the carriers into the oxide. A potential difference of 2 V across an oxide thickness of 2 nm will cause tunnelling, while a 5 V potential difference
74
across 5 nm oxide won't. Fin ally, the increasing number of SeEs, in particular t he t hreshold voltage roll-off effect, requires addit ional local pocket implants in t he channel region close to the source and dra in. This leads to a larger reverse-bias drain junction leakage current . A few ot her leakage mechanisms cont ribute to the total leakage, such as gate-induced dra in leakage (GIDL) and impact ionisation current. T he next subsections will discuss t he mechanisms behind these leakage currents in more detail. Particularl y during t he stand by mode of most port able electronic devices t hese leakage currents cause a relat ively large standby power , t hereby limit ing t he battery lifetime. Design methods to reduce these leakage power components are present ed in chapte r 8.
2.7.1
Weak-inversion (subthreshold) behaviour of the MOS transistor
An nMOS transist or operates in the 'weak-inversion' region when its gate-source voltage (Vgs ) is below its t hres hold voltage (VT), see figure 2.14.
10-4
0.1
10-5
[mNllm] 0.08
Ids [Nllm]
i
Ids log scale
i
10,6
0.06
10,7
0.04 linear scale
10,8 10,9 0
0.2
0.4
0.6
--Vgs
0.8
1.0
0.02
0 1.2
[V]
Figur e 2.14: MOSFET current representation on linear scale (right axis) and log scale (left axis)
75
Below the threshold voltage, the current decreases exponentially. On a logarithmic scale, the slope (for gate voltages below the threshold voltage this slope is called the subthreshold slope) is inversely proportional to the thermal energy kT. Some electrons still have enough thermal energy to cross the gate-controlled potential barrier (figure 2.15) and travel to the drain. At (very) low threshold voltages, the resulting subthreshold leakage current may lead to an unacceptably high power consumption. This leakage current should not exceed a few tens of nano-amperes for a one hundred million transistor chip in standby mode (no circuit activity and at zero gate voltage) . This operating region is also called the 'subthreshold region'. The subthreshold slope (Ssubthr) depends on the technology and is expressed in mV/ dec. The lower the value , the steeper the slope. It ranges from Ssubthr ;::;:; 63 mV/ dec for sor processes to Ssubthr ;::;:; 80 mV/ dec for bulk CMOS processes. This means that the subthreshold leakage current increases about 18 times for every 100 mV reduction in VT , for bulk CMOS transistors. The normal strong-inversion equations (that apply above the threshold voltage) do not apply to the weak-inversion region. The drain-source current in a transistor with a long channel and a constant drain-source voltage operating in the weak-inversion region is expressed as follows:
Idssub -- WeI L . dsO eVgs /mUT
(2.17)
The terms in equation (2.17) are defined as follows:
C
1 - e-Vds /UT
kT - ;::;:; 25 mV at room temperature q
m
characteristic current at Vgs = aV; 1 dsO ex: e- VT/mUT slope ;::;:; 1.5 and depends on the channel length
Equation (2.17) applies when Vgs is not larger than a few UT below VT. The subthreshold transistor current 1dssub can lead to a considerable standby current in transistors that are supposedly inactive. Expression (1.16) in chapter 1 shows that when we apply a negative (positive) voltage to the substrate or back gate of an nMOS (pMOS) transistor, we can increase the threshold voltage, thereby reducing the subthreshold leakage. Methods to use this back-bias effect in reducing the standby power of CMOS rcs, are discussed in chapter 8.
76
An accurate description of the behaviour of a transistor operating in the weak-inversion region is contained in references [8,9]. The following statements briefly summarise this operating region: 1. At low VT, there is a significant subthreshold current when Vgs aV. This has the following consequences:
=
(a) There is a considerable standby current in (C)MOS VLSI and memory circuits; (b) The minimum required clock frequency of dynamic circuits is increased as a result of leakage currents. DRAMs are among the circuits affected. 2. In long-channel transistors, the source and drain depletion regions have a limited influence on the electric field in the channel. These devices show a much lower threshold-voltage dependence on channel length and drain voltage. In short-channel transistors, on the contrary, the source and drain depletion layers cover a much larger part of the channel (see figure 2.7). They interact with each other, such, that the drain voltage reduces the potential barrier at the source. Figure 2.15 shows the influence of the drain voltage and channel length on the barrier height . An increase of the drainsource voltage in short-channel transistors will reduce the barrier height. This Drain-Induced Barrier Lowering effect (DIBL) leads to a reduction of the threshold voltage VT of th e transistor.
77
short channel
Vs source
~DIBL
long channel
•
• L
drain F igure 2.15: The effect of the drain voltage on lowering the barrier
In a 65nm CMOS technology, for examp le, a transistor wit h a channel length of 60 nm can carry a 6 times larger subthreshold leakage current t ha n one wit h a channel length of 90 nm at t he same operating voltages! T he total subthres hold leakage cur rent is also depend ent on t he temperature : it almost doubl es for every 25°C increase in te mperature . It is clear t ha t these effects are very impo rtant in t he development and the modelling of deepsubmicron techno logies. 3. Analogue circuit techniques use weak-inversion behaviour in lowcur rent applications. The volt age gain of a MOS t ransistor operating in t he weak-inversion region is relatively high and comparable to the voltage gain of bipolar transist ors.
2.7.2
Gate-oxide tunnelling
The conti nuous scaling of MOS devices over t he past four decad es has caused a redu cti on of t heir lateral dimensions with an average scaling factor s :::::! 0.7. In order to achieve a higher speed, the transistor cur rent
78
needs to be increased. From t he current expressions, derived in chapter 1, it can be seen, t hat we need to increase t he tra nsistor gain factor {3, in order to achieve a higher current drive. Because {3 is inversely proportional to t he gate-oxide t hickness t ox . This t hickness was requir ed to be reduced wit h the same factor, leading to an increasing probability of direct electron t unnelling through it. However , when t ox becomes less t han 2.5 nm , t his tunnelling becomes visible in t he total t ransist or leakage picture. Both t his probability and t he resultin g leakage current are st rong exponent ial functions of t ox , as well as a functi on of t he voltage across the gate oxide [11] . It is not only t he electrical field across the oxide t hat det ermin es t he amount of t unnelling, but also, and even more dominantly, the penetr ation of carriers into t he oxide , e.g., 2 V across 2 nm oxide causes tunnelling, while 5 V across 5 nm does not. Figure 2.16 shows these relationship s [8] . Th e gate leakage increases roughly by a factor of ten for every 0.2 nm reduction in oxide thickness. It also increases by about a factor of ten with the doublin g of the voltage across t he oxide.
,.......,
'"E u
----c
'--' """-)ell
2 10 1 10 0 10 10- 1
lo ~- 1.4nm
;::;-' 40
E u
s---
10-2 10-3
ell
"""-)
10-4 10-5
20
0 0
0
1.5
0.5
1.5
0.5
Vg [V]
V. [V]
Figure 2.16: Gate-oxide leakage current density as a function of the oxide thickness and oxide voltage
The tot al gate-oxide leakage is dependent on the state of the transistor. In t he tr ansistor on-st at e, the whole channel area cont ributes to the gateoxide leakage current . In the off-state, only t he gate-to-source and/or gate-to-dra in overlap area cont ribute , depending on t he volt age on these terminals. It should be not ed that gate-oxide (Si0 2 ) leakage will be dominated by t he n-MOS device, beca use t he p-MOS device shows an increased barrier for hole t unneling. As a result , a pMOS transistor will exhibit
79
roughly an order of magnitude lower gate-oxide leakage current than its nMOS counterpart [9] . The gate-oxide leakage can be reduced by applying an isolating material with a relatively high dielectric constant, so that the dielectric thickness can be increased and the gate-oxide leakage reduced. Researchers are currently exploring the potential of hafnium-based dielectrics (e.g., Hf0 2 , HfSiO, HfSiON), but most of these materials show poor electrical stability, low charge-trapping capability, yield and reliability. Further research is still required to improve the quality of a new gate dielectric.
2.7.3
Reverse-bias junction leakage
In commonly used CMOS circuits, when the source and drain junctions are biased, they are reverse biased. The larger reverse bias across the drain junction is particularly responsible for the increasing junction leakage. There are several mechanisms that contribute to this junction leakage. Two of them, which are commonly known from the basic conventional diode operation, are diffusion and drift of minority carriers and electron-hole pair (Shockley-Read-Hall; SRH) generation in the depletion region of the reverse biased junction. For the lower temperature range, the generation mechanism dominates and is proportional to the intrinsic carrier concentration tu. The diffusion mechanism is dependent on the thermal energy kT, which causes the carriers to move at random even when no field is applied. At high temperatures, this dominates the leakage contribution, which is then more proportional to ni 2 . If the reverse electrical field increases but is still in the relatively low region, the reverse leakage current is mainly assisted by interface traps. This so-called trap-assisted tunnelling (TAT) increases with the density of traps and can be increased by electrical stress. If no special technology measures had been taken, four decades of transistor channel length scaling would have resulted in the source and drain depletion layers touching each other, causing the SCE as discussed in section 2.5.1. To suppress SCE , close to the source and drain regions in the channel, halos (pockets) are implanted with increasing peak doping levels (::::::: 1 - 2.10 19 atoms/em") , depending on the technology node . Because of this, the depletion layers become so thin, that also here direct tunnelling of carriers will occur , just like through the thin gate oxide. A high field across the reverse-biased p-n junction at the drain causes significant tunnelling of electrons through this junction, from the valence 80
band of the p-halo to the conduction band of the n-drain (figure 2.17). This so-called sub-surface band-to-band tunnelling (sub-surface BTBT) is a major contribution to the total reverse-bias junction leakage current at high reverse electrical fields. £ c - - - - --.
" -- - - - - £v
n-drain
p-halo
Figure 2.17: Sub-surface BTBT through an nMOS drain junction This BTBT-Ieakage current is exponentially dependant on the reversebias electric field across the junction and on the doping levels at both sides of the junction. The use of a negative back-bias voltage increases the reverse-bias potential and may lead to a dramatic increase of this BTBT leakage. So, the use of a reverse body-bias to reduce the overall transistor leakage becomes questionable, since it influences the various leakage components in a different way: it will reduce the subthreshold leakage, but it will increase the reverse-bias junction leakage. Section 2.7.6 presents a discussion on the combined leakage behaviour in relation with the temperature and the use of a reverse body bias.
2.7.4
Gate-induced drain leakage (GIDL)
When a large drain-to-gate bias is applied, a deep depletion condition is created in the drain region underneath the gate. This can create a sufficient energy-band bending (greater than the silicon bandgap) at the Si-Si0 2 interface in the drain for valence-band electrons to tunnel into the conduction band. In other words: when , in case of an nMOS transistor, Vgs ::; 0 V while Vds = Vdd, electrons may tunnel through this deep-depletion layer and flow to the drain terminal, while the remaining holes flow to the substrate. Figure 2.18 shows the effect by the energy band diagram. 81
Ib
.........................................
p-type ubstrate
gate
I
oxide
drain
Figure 2.18: Cross-section and energy-band diagram used to explain the GIDL effect
This surface BTBT together with trap-assisted tunnelling current at the interface are the main causes of the so-called gate-induced drain leakage (GIDL) current [10]. This current only depends upon the conditions near the gate to drain overlap. A decreasing gate-oxide thickness causes an increase of the drain-to gate electrical field and results in an increase of the GIDL current. The resulting drain and substrate currents increase exponentially with Vdg . The effects of GIDL remain almost constant with constant-field scaling (see chapter 11). It is not expected that the use of high-s dielectrics will have much impact on GIDL .
2.7.5
Impact Ionisation
As a result of the continuous scaling of the devices, the electric field near the drain has reached extraordinary large values in short-channel devices. Consequently, a carrier can acquire sufficient energy that it can cause impact ionisation upon impact with an atom, e.g., such a hot carrier can cause the transition of an electron from the valence band to the conduction band , leaving a free hole behind. This produces an ext ra conduction electron and a hole. These generated carriers face the same large electric field that has caused their formation. Therefore, in an nMOS device, both electrons will flow to the drain, while the hole drifts to the substrate. In other words: impact ionisation occurs , when the excess of energy that a carrier has collected , from passing a high electric field, is used to create other carriers. This gives rise to an increase in 82
t he drain-sour ce current I ds and to a subst rate current h. The degree to which impact ionisation occurs and t he magnitude of h are directly proport ional to t he square of the maximum electric field in the pinch-off region near t he drain. Every measure to reduce this max imum causes a reduction in h . In an nMOS device, a carrier impact may generate high-energy electrons which may be scattered toward t he substrate-to-gate oxide int erface. Electrons wit h the highest energy can even be inject ed into t he gate oxide. This so-called hot-carrier effect will degrade t he device performance and it may lead to reliability problems (see chapter 9). Impact ionisation and t he occurrence of hot carriers are more pronounced in short-c hannel devices operating at t he maximum drain source voltage (equa l to the suppl y volt age), when the gate source volt age is equal to half of the suppl y volt age. Because analog circuits te nd to be designed with non-minimum channel length devices, t hey will suffer less from t hese effects. Because t he bandgap of silicon is 1.15 V, the t rend of reducing t he supply voltages further below 1.2 V, will cause a reduction of occurre nce of impact ionisation in fut ure CMOS devices.
2.7.6
Overall leakage interactions and considerations
T he previous subsectio ns presented the most impo rtant individual leakage components in an MOS transistor. However, these leakage components are int erd ependent and respond differently to a change in one or more of the parameters (e.g., oxide thickness, channel length, channel doping, source and drain doping, gate material/ doping, terminal voltages, chip temperature). Figure 2.19 (top) shows an example of the gate, dr ain , and bulk currents of an nMOS transistor in a 65 nm low-leakage (LST P ) CMO S t echnology as a function of t he gate voltage at 25 "C and 125 "C. Figure 2.19 (bottom) shows the influence of an additional reverse subst ratebias voltage on t he curre nt-to -voltage behaviour .
83
10-2
-
10-3 10-1
-
-
-
-
-
--------,
- - Temp = 250 ------ Temp = 1250
, / drain
/,:'
10-5
10-6
.,, . . .. ,, .. ,.
10-7
IO-K 10-9 10-10 10-11 10-12 10-13 10-14
current
,
bulk
curr mt
IO - I S ~'- - - - - - ' - - - ' - - - - - ' - - - - - ' - - '
-1.0
-0.5
0.0
0.5
1.0
Vgs [V] 10-2 10-3
10-1 subthreshold leakage
10-5
10-(,
.......
s
-
Vb, = 0 Vbs = - I V
10-7
IO-K
-~\ / l> l 'b - -3
10-9
-1.0
-0.5
0.0
0_5
1.0
Vgs [V]
Figure 2.19: Most dominant contrib utions to the tota l leakage current in an nMO S transistor in a low-leakage 65 nm CMOS technology at 25 0 C and 125 0 C (top), and at different back bias voltages (bottom) The subthreshold current is exponent ially proportional with t he te mperature , while the gate t unnelling current is almost completely independent of it . For an nMOS tra nsisto r in a general-purpose 65 nm CMOS technology, t he cont ribut ions of the gate and subt hreshold currents will
84
dramatically increase, because such a process has a much thinner gate oxide and a smaller VT.
130nm
IOOnm
65nm •
ubthre hold leakage from ource
•
Gate-induced drain leakage (GIDL)
•
Junction rever e-bia leakage Gate-leakage (direct tunneling)
Figure 2.20: Relative contributions of the various leakage mechanisms to the total transistor leakage current [12J Figure 2.20 shows an example of the relative contributions of the various leakage mechnisms to the total transistor leakage current [12], which itself increases exponentially (Figure 2.21; [13]) with further technology scaling. It reflects a process with very thin gate oxide . However, these contributions may vary dramatically between different technology nodes and between low-power and general-purpose processes from different foundries.
85
Intel 20 nm / trans: lor
I. E-04
t--~--,.'--'-"===-------------
I. E-06
t--z-__'-""oli,.........z....- - - - - - - - - - - -
E
~ I . E-08
f---;------""""':O<'---"'dIf - - - - - - - - - -
'--'
!::: ......0
I. E-IO I - - - - - - T - - - --"o,c--- - - - - - I. E-12
t------------~_----
I. E-14 + - - - - -10
-
-
- , . -100
-
-
-
-
-
-
--, 1000
Physical gate length [nm]
Figure 2.21: Exponent ial increase of th e total leakage current vs channel length (technology generation) [13} More on leakage current mechanisms can be found in [14]. Altern ative technology and design solut ions t o reduce leakage currents are presented in chapte r 8.
2.8
MOS transistor models
All previously discussed physical mechanisms, combined with an accurate description of t he (overlap) capacitances, are included in today's (compact) MaS models. A MaS model gives a description of the physical behaviour of a Ma S device from weak-inversion to strong-inversion operation and calculates the device currents, charges and noise as a function of the te rminal volt ages. Par ticularl y the analog and RF applications of the MaS t ra nsistor require an accurate description of their operation over t he full range of operat ing volt ages. A compact model is based on only a limited numb er of parameters. In combination with a circuit simulat or, a compact model allows full simulation of t he electrical behaviour of rather complex analog and RF circuits and predicts their behaviour, before they are integrat ed on real silicon.
86
The majority of recently developed MOS models are based on socalled surface-potential (SP) models, in which the surface potential equations at both ends of the channel are solved. In December 2005 the Compact MOS Council (CMC) has selected the PSP model, which was a merge of two existing SP models, to replace BSIM as the industrial standard MOSFET model for future CMOS technologies [10,15]. More details about the physical and mathematical basics of MOS modeling are beyond the scope of this book, but are largely available through the internet.
87
2.9
Conclusions
The formulae derived in chapter 1 provide a good insight into the fundamental behaviour of MOS devices. These formulae were used to predict circuit behaviour with reasonable accuracy until the mid 1980-ies. The continuous drive for higher circuit densities with smaller transistors, however, has given rise to an increased contribution from physical and geometrical effects. These effects cause deviations from the ideal transistor behaviour assumed in chapter 1. In addition, the magnitude of these deviations increases as transistor dimensions shrink. These effects combine to reduce the ideal transistor current by more than a factor four for channel lengths below 0.25 tu», There are also effects that permanently degrade the performance of a MOS transistor. Particularly its behaviour in off-state has a great impact on the standby power consumption of CMOS ICs. Therefore weak-inversion behaviour and transistor leakage-current mechanisms have been discussed in detail, to allow better understanding of the low-standby power solutions presented in chapter 8. The continuous scaling of both devices and interconnects also has severe consequences for the reliability of the IC and may dramatically reduce its lifetime. These consequences and potential technology and design solutions are discussed in chapter 9.
88
2.10
References
[1] A.J . Walker and P.H. Woerlee, 'A mobility model for MOSFET device simulations', Journal de Physique, colloque C4, Vol. 49, No.9, Sept. 1988, p. 256 [2] M.Vertregt, 'T he Analog Challenge in Nanometer CMOS' , IEDM Digest of Technical Papers, pp. 11-18, December 2006 [3] RS.C. Cobbold, 'T heory and applications of field effect transistors', John Wiley & Sons, Inc. New York [4] LM. Filanovsky, A Allam , 'Mutual Compensation of Mobility and Threshold Voltage Temperature Effects with Applications in CMOS Circuits', IEEE Transactions on Circuits and Systems : Fundamental Theory and applications, vol. 48, no. 7, pp. 876-884, July 2001 [5] E. Long, et al. 'Detect ion of Temperature Sensitive Defects Using ZTC', Proceedings of 22nd IEEE VLSI Test Symposium (VTS 2004) [6] A. Dasnan, et aI., 'Handling Inverted Temperature Dependance in Static Timing Analysis', ACM Transactions on Design Automation of Electronic Systems, Vol. 11, No.2, April 2006, pp. 306-324 [7] RKumar, et aI., 'Reversed Temperature-Dependent Propagation Delay Characteristics in Nanometer CMOS Circuits', IEEE Transactions on Circuits and Systems-II: Express Briefs, Vol. 53, No. 10, October 2006, pp. 1078-1082 [8] R van Langevelde, et aI., 'Gate current: modelling, LlL extraction and impact on RF performance' IEDM Technical Digest , pp. 289-292, 2001 [9] F .Hamzaoglu , et aI., 'Circuit-Level Techniques to Control Gate Leakage for Sub-100nm 89
CMOS' Proceedings of the 2002 ISLPED Symposium, pp. 60-63 [10] G. Gildenblat, et al., 'PSP: An Advanced Surface-Potential-Based MOSFET Model for Circuit Simulation', IEEE Transactions on Electron Devices, Vol. 53, No.9, pp.1979-1993 , September 2006 [11] D. Lee, et al. , 'Gate Oxide Leakage Current Analysis and Reduction for VLSI Circuits', IEEE Transactions on VLSI Systems, Vol. 12, No.2, February 2004, pp. 155-166 [12] J. Assenmacher, 'BSIM4 modelling and Parameter Extraction', http: / /www.ieee.org/ r5/ denver / sscs/ References/ 2003_03_Assenmacher.pdf [13] G. Marcyk, et al. , 'New Transistors for 2005 and Beyond ', http: / /www.eas.asu.edu / vasilesk/EEE531 / TeraHert zlong.pdf [14] A. Scholten, et al., 'T he Physical Background of JUNCAP2 ', IEEE Transactions on Electron Devices, Vol. 53, No.9, pp.2098-2107 , September 2006 [15] R.Woltjer, et al. , 'An industrial view on compact modeling' , Proceedings of the 36th European Solid-State Device Research Conference, Sept. 2006, Page(s):41 - 48
General basic physics [16] S.M. Sze, 'Very Large Scale Integration Technology ', Mc Graw-Hill, 2nd edition, 1998
90
2.11
Exercises
1. At 25°C the magnitude of an nMOS transistor's gain factor 240/JAjV2 and its threshold voltage VT is 0.4 V.
f3 is
a) Calculate the gain factor (3 when th e t ransistor is operating at 65°C . b) Calculate the threshold voltage for th e temperature in a). c) What would be the consequences of this reduced threshold voltage for the standby current in an SRAM, for instance? 2. Assume the transistor in exercise 1 is saturated with its gate connected to its drain. At what Vgs would th e influence of the temperature difference in exercise 1 on the gain factor (3 and on the threshold voltage VT fully compensate each other (in other words: what would be the ZTC voltage value of Vgs )? 3. a) What is the effect on the gain factor (3 of a pMOS transistor with L = 60 nm when the mobility is only influenced by velocity saturation caused by a very large horizontal electric field, Ex = 0.9· Ex sat ? b) Calculate th e drain-source voltage at which the relevant reduction in mobility occurs if 03 = 0.45 V-I. 4. Assume equat ion (2.7) can be approximated by:
What can you say about the relation between the mobility and the series resistance of the drain (Rd) , when the transistor operates in the saturation region?
91
Chapter 3
Manufacture of MOS devices 3.1
Introduction
Until the mid-eighties , the nMOS silicon-gate pro cess was the most commonly-used pro cess for MOS LSI and VLSI circuits. However, nearly all modern VLSI and memory circuits are made in CMOS processes. CMOS circuits are explained in chapte r 4; t he technology used for t heir manufacture is discussed in this chapte r. Modern nanom et er CMOS pro cesses, with channel lengths below 100 nm , have emerged from the numerous manufacturing pro cesses which have evolved since the introduction of the MOS transistor in integrated circuits. Differences between the processes were mainly characte rised by the following features: • The minimum feature sizes that can be produced. • The gate oxide thickness. • The numb er of int erconn ection levels. • The typ e of substrat e material. Alternatives include n-type and p-typ e, high-resistive or low-resistive, bulk silicon, epit axial or SOl wafers. • The choice of the gate material. Initially, the gate material was th e alum inium implied in the acronym MOS (Metal Oxide Semicondu ctor). Molybd enum has also been used. Until 120nm MOS 93
processes and above, however, nearly all use polycrystalline silicon (polysilicon) as gate material. One of the main reasons is that a polysilicon gate facilitates the creation of self-aligned source and drain areas. Another reason for using polysilicon as gate material is that it allows accurate control of the formation of the gate oxide. From 90 nm onwards, a stack of W-WN-polysilicon and SiOxNy is used. A combination of a metal gate with high-s dielectrics is first introduced in the 45 nm node , but will certainly be an option in the 32 nm node . • The method to isolate transistors. Conventional CMOS processes used the so-called LOCOS isolation while most of today's processes use Shallow-Trench Isolation (STI), see section 3.5. • The type of transistors used: nMOS , pMOS, enhancement and /or depletion, etc. Many of the transistor parameters, in terms of performance, power consumption, and reliability, are determined by the substrate that is used as starting material. A short summary on the properties and use of the different substrate materials will therefore be presented first. Modern manufacturing processes consist of numerous photolithographic, etching, oxidation, deposition, implantation, diffusion and planarisation steps. These steps are frequently repeated throughout the process and they currently total more than 500. The IC fabrication discussion starts with a brief description of each step. Most processes use masks to define the required patterns in all or most of the IC diffusion and interconnect layers. Modern CMOS manufacturing processes use between 25 and 50 masks. However, the initial discussion of IC manufacturing processes in this chapter focuses on a basic nMOS process with just five masks. Subsequently, a basic CMOS process flow is briefly examined. fundamental differences between various CMOS processes are then highlighted. Finally, a sample nanometer CMOS process is explained. Many of the associated additional processing steps are an extension of those in the basic CMOS process flow. Therefore, only the most fundamental deviations from the conventional steps are explained. The quality and reliability of packaged dies are important issues in the IC manufacture industry. An insight into the associated tests concludes the chapter.
94
3.2
Different substrates (wafers) as starting material
A very critical element in the operation of an integrated circuit is the electrical isolation between th e individual devices. Unintended electrical interference can dramatically affect their performance. Smaller minimum feature sizes reduce the distance between devices and increase their sensitivity at the same time . An important factor in the isolation properties is the substrate on which the devices are built. In all discussions , so far, we have assumed a bulk silicon substrate (wafer) as the starting material for our (C)MOS processes. However, most standard CMOS technologies today use epitaxial wafers, while several high-performance microprocessors are made on SOl wafers. The properties and use of these substrates (wafers) will be discussed next.
3.2.1
Wafer sizes
From an economical perspective, larger wafers have lead to reduced IC manufacturing costs. This rule drove the wafer diameter from about 1 inch (~ 25mm) , about four decades ago, to 12 inches (= 300mm) today. This has put severe pressure on maintaining the wafer flatness , its resistivity and low crystal defect density homogeneous across a rapidly increasing wafer area. However, the introduction of a new wafer diameter generation requires a huge amount of development costs. A possible move from 300 mm wafer fabs to 450 mm wafer fabs may need $15 billion to $20 billion of development costs [1] . According to the International Technology Roadmap for Semiconductors (ITRS) , a 450 mm fab is projected to emerge around 2012 or so. This huge investment can only be earned back by those companies that run expensive products in very high volumes. All semiconductor tool vendors currently have no investments in the development of 450 mm tools, so it is questionable whether the first 450 mm waferfab will be built before 2015.
3.2.2
Standard CMOS Epi
Epitaxial wafers consist of a thin, mono-crystalline silicon layer grown on the polished surface of a bulk silicon substrate [2] . This so-called epi layer is defined to meet the specific requirements of the devices in terms of performance, isolation and reliability. This layer must be free of surface imperfections to guarantee a low defect density and limit the 95
number of device failures. Since t he carriers in a t ra nsisto r cha nnel only t ravel in the sur face region of t he device, the epi layer t hickness is only defined by t he tra nsistor architecture (source/drain and ST I depths) and ranges from one to a few microns . Usually t he total wafer t hickness is ty pically 750 J.lm , but may range betwee n 400 usi: and 1 mm , depending on the wafer size and technology node. It mean s t hat t he to p epi layer form s only less than one percent of t he total wafer and that t he maj or par t of the wafer mainly serves as a substrate carrier for the ICs made on it. Although t he resist an ce of this substrate hardly affects the performan ce of digit al circuits it has influence on t he robu stness of the ICs buil t on it . Most convent ional CMOS pro cesses, including t he 180 nm node, use/used low-resistivity (5-lOmOcm at doping levels between 5.1018 and 1.1019 atoms /crrr") wafers, in ord er to reduce the cha nce of latch-up occur rence (see cha pte r 9) . Wi th reducing supply volt ages the chance for tri ggering the par asiti c t ra nsist or to initiat e lat ch-up, is also diminishing. This, combined with t he increasing int egration of GHz RF functions, has mad e t he use of high-resisti vity (l0-50 n cm at doping levels between 1.1015 and 1.5 15 atoms /cm''] substrates very popul ar from the 120 nm CMOS node onwards. It leads to perform an ce increase of passive components, such as inductors, but also to a bett er elect rical isolation between t he noisy digit al circuits and t he sensitive RF and analog ones (less substrate noise; cha pter 9). Becau se t he full device ope ration occur s wit hin t his thin to p epi layer , it pu ts severe demand s on t he homogeneity of the layer t hickness , of t he resisti vity and of t he crystal defecti vity. Wh en growing single crystal silicon, eit her for creating bulk silicon wafers or for creating t hin epi layers, a few ty pical defects in the silicon may show up. Point defects may originate from single empty locations (vacancies ) in th e monocrys tallin e ato mic stru ct ure (figure 3.1) , while micro defects or crystal-oriented particles (COP) can be t he result of a cluster of voids.
96
Microdefects
Point Def ects
-
1 ~
\ oid» (r-clu tcr .
Vacancic
[) D . feels or (01' )
T Bdc~
(1·c1US1cn)
Dislocations (i-clusters. A Defects dislocation loops from inter stitial agglomcrute, )
Lanitt
lntcrstitials B J."!.cu inlalli«
Figur e 3.1: Defects in silicon (Sour ce: MEMC)
Interstitials are at oms located in between the atoms of the crystal, while dislocations may be caused by clusters of interstitials. The average at omic spacing is also dependant on the covalent atomic radius of the specific material: Silicon (Si) 1.17 A, Boron (B) 0.88 A, Phosphorous (P) 1.10 A, Arsenic (As) 1.18 A, St ibnite (Sn) 1.36 A. So, B is a smaller atom than Si. Doping Si with B (or P) reduces the average atomic spacing of t he Si crystal. Another result of thi s is t hat the average atomic spacing in the p- epi layer is larger than t hat in the p" subst rate, because the substrate cont ains a higher concent ration of smaller atoms. Large differences in the atomic spacing of different layers may lead to so-called misfit dislocation s. To prevent misfit dislocations in a t hin epi layer on a resistive substrate a simple rule of t humb is applied [3,4] : epi thickness in tun ::; substrate resistivity in
illn
Stand -alone memories may require their own substrates. Trench capacit or DRAMs (chap ter 6), for instance, in which t he trench capacitor cells are fabric at ed inside the substrate using depths over 7/-lm , have much more int eraction with the silicon (defects , leakage, st ress) tha n st ackedcapacitor DRAMs (chapter 6), where t he capacit or is located fully above the silicon. They t herefore need a low-COP or defect-free top layer with 97
a thickness larger than the trench depth, to prevent substrate defect generation during the deep-trench fabrication . These examples show that not all ICs can be made on the same substrate. The following subjects discuss substrates that enhance the device performance.
3.2.3
Crystalline orientation of the silicon wafer
As discussed in chapter 2, the effective mobility of the carriers in the channel has reduced dramatically over time, due to the continuous scaling of the transistors. Suppressing short-channel effects by increasing the channel doping has led to an increased density of charged impurity scattering sites, thereby reducing the mobility of the carriers in the channel. The intrinsic speed of a logic gate, in first approximation, is proportional to the mobility. Therefore, a lot of research is currently performed in a variety of ways to improve carrier mobility. In this respect also the crystalline orientation of the silicon substrate plays an important role. Traditionally, CMOS has been fabricated on wafers with a (100) crystalline orientation, mainly due to the high electron mobility and low interface trap density. However, the pMOS transistors on this substrate suffer from a low mobility. By moving away from the (100) orientation, electron mobility is degraded, while hole mobility is improved. Compared to a traditional (100) wafer, a (110) wafer can show hole mobility improvements up to 30% in practice, while electron mobility may have degraded by about 5-10%. An optimum technology, with a much better balance between nMOS and pMOS device performance would be a hybrid-orientation technology: the (100) plane for NMOSts and the (110) plane for the pMOSts [5,6], see also section 3.9.4. If the pMOS channel is oriented along the < 100> direction on a (100) wafer, its mobility and performance may be increased by about 15%, with almost no degradation of the nMOSt performance. Another advantage is that the pMOS transistor will also exhibit a reduced variability. This is only a minor change in the starting wafer, with no further consequences for the device technology and layout (figure 3.2).
98
(100) surface orientation <100>
<100>
- - - - - notch - - - Figure 3.2: a) traditional notch grinding and b) grinding the notch in the <100> direction (Source: MEMC) The only difference is that the wafer fiat alignment or notch is changed from the standard <110 > direction to the < 100> direction. Traditionally, the notch is cut during crystal grinding in the < 110> direction (figure 3.2.a) . To orient the channel direction along <100 > , requires a crystal rotation of 45° to grind the not ch in < 100> direction (figure 3.2.b) . This orientation change is a low cost solution to enhance the pMOS device, logic gate and memory cell performance with no risk or consequences for the integration process. This wafer option is already in use in high volume production
3.2.4
Silicon-an-insulator (SOl)
Bulk-CMOS devices show relatively large source/drain capacitances . This can be avoided with the SOl-CMOS devices illustrated in figure 3.3. The complete isolation of nMOS and pMOS transistors associated with this process also completely removes the possibility of lat ch-up.
99
nMOST
pMOST
i olating substrate
Figure 3.3: Cross-section of a basic SOl-CMOS process Neither the nMOS nor pMOS transistor channels require over-compensating impurity dopes. Very small body effects and source /drain capacitances are therefore possible for both types of transistor. In addition, the n" and p+ source and drain regions do not have bottom junctions. Consequently, the parasitic capacitances are much less than those of the bulk-CMOS processes. This makes the SOl-CMOS process particularly suitable for high-speed and /or low-power circuits. Murphy's law, however, ensures that there are also several disadvantages associated with SOl-CMOS processes . The absence of substrate diodes, for example, complicates the protection of inputs and outputs against the ESD pulses discussed in chapter 9. Sapphire was originally used as the isolating substrate in SOl-circuits, despite the fact that it is substantially more expensive than silicon. The SIMOX ('Separation by IMplantation of OXygen ') process provides a cheap alternative for these silicon-on-sapphire or 'SOS-CMOS' processes. Several modern SOl-CMOS processes are based on SIMOX. These processes use a retrograde implantation of oxide atoms to obtain a highly concentrated oxygen layer beneath the surface of a bare silicon wafer. The resulting damage to the wafer's crystalline structure is corrected in an annealing step. The result is shown in figure 3.4.
100
/ 0.2 J.I m
/
Si
S i~
./
Si- ub.trlllC )
(b)
(a)
Figure 3.4: (a) Cross-section of a SIM OX wafer and (b) SEM photograph of such a cross-section SIMOX wafers are delivered with a buried-oxide layer (BOX layer) (Si02) varying from less than 50 nm to 150 nm , with a t op silicon layer varying from less than 10 nm to 100 nm [7]. This is done to reduc e the consequences of damage on the wafer surface. Fully deplet ed devices can be realised by reducin g the t hickness of the t op layer to below 50 nm , for example, during processing. An alt ernative to the SIMOX process flow to create SOl , is the Smart Cut pro cess flow (figure 3.5)
hydrogen implantation
iO~
"handle" wafer
..
! bonding
plitting
Figur e 3.5: Smart-C ut process flow (So urce: SOITEC) After t he original wafer is first oxidized to create an isolatin g layer , H+ ions are implanted to form a "weak" layer at a certain dist ance 101
below the surface. The thickness of the top layer is determined by the implantation energy. Next the wafer is cleaned and bonded upside-down to another wafer for further handling. During the "smart cut" step, the wafer is heated, such that the wafer is split exactly at the implanted weak H+ layer. The remaining part of the wafer is reused again as original wafer, or as carrier for a new SOl wafer, and the process cycle starts again. Finally, the SOl wafer needs an annealing step to recover the atomic structure, which was damaged during the implantation step. After a CMP planarisation step, the SOl wafer is ready. This smart-cut technology can be used for a wide range of SOl and BOX thickness. In an SOl device with a thick top silicon layer (figure 3.6.a), this layer can only become partially depleted (PD-SOI) during operation, showing such parasitic effects as the floating-body and Kink effect. A thin-body device «50 nm) (figure 3.6.b) will become fully depleted (FD-SOI) and does not show these effects .
thin silicon (sub -1 Onm)
thick silicon (1 OOnm or more)
(b)
(a)
Figure 3.6: Cross section of a (a) partially-depleted SOl device and (b) a fully-depleted 501 device For advanced low-voltage CMOS (::;1 V) system-on-chip designs with digital, analogue and RF parts, SOl is expected to offer a better performance than bulk CMOS technology [8,9]. SOl is said to deliver more speed at the same power consumption, or to consume less power at the same speed. Furthermore, SOl realises better isolation between digital, analogue and RF parts on the IC. Those circuits will therefore be less affected by substrate noise. Additionally an SOl transistor has lower parasitic capacitances and consequently exhibits a better RF performance. SOl devices are thermally insulated from the substrate by the
102
buried-oxide layer. This leads to a substantial elevation of temperature (self-heating) within the SOl device, which consequently modifies the output IV-characteristics of the device, showing negative conductance. These effects, which are considerably larger in SOl than in bulk devices under similar conditions, must be taken into account by device technology engineers , model builders and designers. Since the body is isolated, SOl circuits show several advantages, compared to bulk-CMOS: • smaller junction capacitances • no deep well required (this is especially an advantage for FD-SOI) • less n+ to p+ spacing, due to absence of wells • significant reduction in substrate noise (questionable at high frequencies > 1.5 GHz) • no manifestation of latch-up • reduced soft-error rate (SER) , because the electron-hole pairs generated in the substrate can not reach the transistors • steeper subthreshold slope, which can be close to the theoretical limit of 63 mV/ decade, compared to around 80 mV/ decade for bulk CMOS devices The future for planar partially depleted SOl devices is not completely clear. The relative performance benefit due to the smaller junction capacitances of SOl will gradually reduce because this advantage diminishes with scaling. Junction area capacitance decreases with the square of the scaling factor while gate and perimeter capacitances decrease only linearly. Next to this, the increasing impacts of interconnect capacitances and delays will also reduce the performance benefits of SOL For the 45 nm node most semiconductor manufacturers still use bulk CMOS as their main process technology. However, beyond this node, FD-SOI may become a good alternative to bulk-CMOS. Since the channel region is fully depleted, it largely eliminates the neutral body. It therefore hardly exhibits the floating-body, history and kink effects. Moreover, it is expected to show improved short-channel effects (SCE) and drain-induced barrier lowering (DIBL) . FD-SOI requires a reduced channel-doping concentration, leading to a higher mobility and a much steeper subthreshold slope, which almost matches the ideal value of ~
103
63 mV/ decad e (figur e 3.7), compa red to t he se 80 mV/ decade for a bulkCMOS pro cess.
--
01 : less leakage compared (0 bulk with same VI
bulk with arne leakage
1'1
"I
1101
V
I bull
Vgs
reduced
Figure 3.7: Schematic illustration of current characteristics and subthreshold behaviour of bulk-CMO S and FD-SOI
The diagr am shows that in an SOl process, a t ra nsistor may have a lower VT than in a bulk-CMOS pro cess, while carrying t he same subt hreshold leakage cur rent . This advantage can eit her be used for sp eed improvement , when running SOl at the same supply voltage as bulk- CMOS , or for power redu ction , when running SOl at a lower supply voltage bu t at the same speed. FD-SOI allows sub-IV RF circuits, with improved Ft and Fm a x and redu ced noise levels. The tran sisto rs in such a nanomet er FD-SOI pro cess are fabricated in a thin film, with a thickness se 10-20 nm. Because the body between source and dr ain is fully depleted , t he VT-spread in these devices is much less dominat ed by the doping levels. Inst ead , it now dep ends heavily on t he film thickness, whose un iformity across an 8 inch or 12 inch wafer has become a major criterion in the success of FD-SOI. This uniformity is t herefore likely t o have a more global (int er-chip) t ha n local (intra-chip) impact on the vari abili ty in device operation. Below the 22nm nod e planar Sal devices are expecte d to show device current degrad ation due to " quant um confinement" [10] . 104
Many other altern ative device and proc ess options are seen as potent ial candida tes for technologies beyond t he 45 nm node. A flavour of technology options in both t he devices and interconnects is pr esented in sect ion 3.9.4.
Figure 3.8: Example of a complex signal processor chip, containing several synthesized functional blocks (Source: NX P Semiconductors)
3.3 3.3 .1
Lithography in MOS processes Lithogr aphy basics
The integration of a circuit requires a t ra nslation of its specifications into a description of the layers necessar y for Ie manufacture. Usua lly, 105
these layers are represented in a layout. The generation of such a layout is usually done via an interactive graphics display for handcrafted layouts, or by means of synthesis and place-and-route tools, as discussed in chapter 7. Figure 3.8 shows an example of a complex Ie containing several synthesized functional blocks. A complete design is subjected to functional, electrical and layout design rule checks. If these checks prove satisfactory, then the layout is stored in a computer file (gds2 file). A software program (post-processor) is used to convert this database to a series of commands. These commands control an Electron-Beam Pattern Generator (EBPG) or a LaserBeam Pattern Generator (LBPG), which creates an image of each mask on a photographic plate called a reticle. Such a reticle contains a magnified copy of the mask patterns. The reticle pattern is thus demagnified as it passes through the projection optics. During the printing process , often pellicles are used to protect the reticle from harmful particles. A pellicle is a very thin transparent membrane adhered to a metal frame, which keeps particles out of focus during the lithographic process, so it will not image onto the wafer and reduces the possibility of printing defects. Particularly with the introduction of 193 nm, the light transmission loss in the pellicles increases with the number of exposures, such that they frequently need to be replaced.
106
PGZ
RI
R2
RP - - tPI. --t--fSfq-- I':l1
BE E B2
PI.
PI.
RP
RP
R3
B1 B2 E
HR C
I
MA P
Bar code area ba rcode rea for 24 character barcode (opbona l) Edge length of the reticle (6" = 152.4 mm ) Human Read ble Code Image field Re ticle alignment mark (PAS 5500 only) Reticle pre alignment mark
Add~iona l
BE
PL
R RP
S
PGZ R1.R4
Bev ened Edge Pellicl e po sition line Canter of reli cle layout Release Pin area Genter of substra te Pellicl e Glue Zone T IS marl<
Figure 3.9: Schematic layout of a 4x reduction reticle for st ep and scan systems (Source: ASML)
107
Small feature sizes, such as currently required in deep-submicron « 0.25 11m channel lengt hs) and nanometer « 100 nm) CMOS processes, are obtained by using reduction steppers or scanners. Current redu ction steppers and scanners use four-to-one (4:1) red uction step-and-repeat and scan-and-repeat operations, respectively. The reduction is achieved by means of a system of (very) complex lenses. Figure 3.10 shows a basic schematic of a gener ic optical projection system.
light
source
illuminator lens reticle
projection lens wafer Figure 3.10: Basic schema tic of generic optical proje ction system 108
Limitations of these projection lithography techniques are not only determined by the wavelength A of the applied light source and the Numerical Aperture N A. A stepper/scanner also needs to create clear , high-contrast images, while it must offer a sufficient depth of focus DOF to accommodate system and process-focus (height) variations which also lead to critical dimensions (CD) variation. The combination of a large number of metal layers and extremely-large-area designs create significant topographies across these designs and put stringent demands to the DOF. Current CMP planarisation technology limits topology variations to below 80 nm. The resolution of the resulting projections is limited by diffraction and also depends on the properties of the photo-resist. Better photoresists allow smaller minimum feature sizes. There are two expressions, developed by Ernst Abbe around 1867, which describe the most important characteristics of a lithographic imaging system. Firstly, the feature size F (= half pitch for memories), which refers to the minimum width of the printed patterns, is defined by:
A
A
F=k1·-=k1 · - NA nsino:
(3.1)
where k1 is a constant, which is a function of the resist, the mask, illumination and resolution enhancement techniques (RET), which will be discussed later. With "conventional" three-beam imaging, where only the zero- (0) and first-diffraction order rays (-1 and +1) pass the lens, the value of k1 is restricted to: k1 2': ~ . When phase-shift masks (PSM) or off-axis illumination (both techniques are explained later in this section) are applied, only two diffraction orders pass through the lens and k1 can be further reduced to : ~ ::; k1 < ~. These techniques are usually also referred to as two-beam imaging. N A represents the numerical aperture and n the refraction index of the medium between the lens and the wafer (1 for an air-based system) and 0: is the collection half angle as shown in figure 3.17. Secondly, the depth of focus DOF , which refers to the distance along the optical axis over which features of illuminated surface are in focus and can be exposed with sufficient accuracy, is defined by: DOF = k 2
n 'A NA2
· -
(3.2)
where k 2 represents another lithographic constant, determining the allowable image blur from defocus. Current values for k2 are around 0.5.
109
Needles to say that F should be minimized and DOF should be maximized. In fact, a trade off has to be made . Whereas the resolution of the imaging system is improving (reducing F) by increasing N A, its depth of focus will be reduced. This reduction can be compensated by a highly planarized top surface for exposure and by DOF enhancement techniques, which are outside the scope of of this text . For many technology generations in the past, the values for k1 and N A were about the same , resulting in minimum feature sizes, which were about equal to the wavelength of the used light source . 0.35 f1m feature sizes were mostly printed on i-line (365 nm) steppers. From a cost perspective, there is a strong drive to extend the wavelength of the light source to smaller technologies . The 248 nm Deep-UV (DUV) steppers, with a krypton-fluoride (KrF) light source, are even used for 90 nm feature sizes, while the argon-fluoride (ArF) 193 nm DUV can potentially be used for feature sizes until 60 nm with dry lithography and until 40 nm with immersion lithography. Steppers (scanners) with shorter wavelengths will become very expensive and need many workarounds, as traditional optical lithography will no longer be viable at much shorter wavelengths. Wh en creating smaller feature sizes with the same wave length, we need to compensate for non-ideal patterning, such as: lens aberrations, variations in exposure dose, pattern sensitivity, die distribution across the reticle and the field (reticle) size. The extension of the use of the 193 nm wavelength to sub 100 nm technologies can not be done without the use of several additional Resolution Enhanc ement Techniques (RET): Optical-Proximity Correction (OPC), Off-Axis illumination (OAI) , Phase-Shift Masks (PSM) , better resist technologies, immersion lithography and design support. In the following these techniques are discussed in some detail to present the reader a flavour of the increasing complexity and costs of the lithographic process, starting with the basic conventional binary mask. The conventional binary mask is used in combination with the 193 nm light source to depict features with half pitch (HP) sizes as small as 90 nm. A binary (photo) mask is composed of quartz and chrome features (figure 3.11) [11] . Light passes through the clear quartz areas and is blocked by the opaque chrome areas. Where the light reaches the wafer, the photo-resist is exposed, and those areas are later removed in the develop process , leaving the unexposed areas as features on the wafer. Binary masks are relatively cheap and they show long life times , because 110
t hey can be clean ed an almost infinite numb er of t imes. Moreover , they use t he lowest exposure dose and ena ble high t hro ughput rates. Preferab ly all masks should be binary masks since it would redu ce t he overa ll production costs .
reticle
••I. --..-.. .
quartz(clear)
r.~.Ii-- chrome (opaque)
pha c
(energy)
intcn ity
(energy')
wafer
-.L_
.....L.....L.....J......I--.L...J'--''-I-........- I - _''''-
remaining
rcsi 'I after develop
Figure 3.11: Basic use of a binary photo mask (Source: ASML) As feature sizes and pit ches shrink, t he resolution of the projection optics begins to limit t he quality of the resist image. In the exa mple above, t here is significant energy (and int ensity, which is proportional to t he square of t he energy) even below the opaqu e chro me areas, due t o t he very close proximity of t he neighbouring clear quar tz areas . This " unwanted" energy influences the quality of the resist profiles, which are ideally vertical. A convent ional binar y mask with a dense pat tern of lines will produce a pat t ern of discret e light diffraction ord ers (-n, -(n-l ),.., -2, -1, 0, 1, 2,.., n-l , n). The example in figur e 3.12 shows a so-called three-beam im aging system. Here a binary mask is used in combination wit h a proj ect ion lens that act s as a first order ray filter. This prevent s t he capture of higher order rays.
111
51 2oc1 and higher order ray arc not captured by reduction lens
/' +2
light A.
photoresist layer
on wafer
---~'l:':': ': : : : : Figure 3.12: Three-beam imaging concept
The interference of the zero-order diffracted light beam with the two first-order diffracted light beams produces a reduced (4:1) image of the pattern. If the line pitch in the pattern becomes smaller, the first-order light beam diffracts with an angle, which is too large to be captured by the lens, which is then incapable of producing the right image. Therefore phase-shift techniques, such as off-axis illumination and PSM, are designed to "sharpen" the intensity profile , and thus the resist profile, which allows smaller features to be printed. When a binary mask is illuminated at a different from normal angle, this angle can be chosen such that one of the first-order diffracted light beams can no longer be captured by the lens and the image is produced by only two diffracted beams (the zero and remaining first-order). This so-called off-axis illumination (OAl) technique (figure 3.13) is therefore an example of two-beam imaging. A further optimisation of this imaging technique can be achieved by choosing the angle of illumination such that the remaining beams are symmetric with respect to the center of the lens. An OAl system can improve the resolution limit of a dense line pattern with a factor of two.
112
one I" and all higher order rays are OT captured by reduction lens
Photoresist layer on wafer
-Me::;"::': ":
..............
Figure 3.13: Off-axis illumination (two-beam imaging concept) However, another benefit from a two-beam imaging system comes from the enhanced depth-of-focus (DOF) . It can be seen that in a three-beam imaging system (figure 3.12), the first-order diffracted beams travel across a different path than the zero-order beam, before arriving at the wafer surface. It can therefore provide only a very narrow range, in which the zero and first diffraction orders remain in phase (basically only in the focal plane) , limiting its depth of focus. Outside this range it creates a phase error. A minor displacement of the wafer out of the focal plane causes an increase of this phase error and leads to a degraded image at the wafer surface. In a two-beam imaging system (figure 3.13), assuming full spatial symmetry, the diffraction patterns are in phase and will interfere properly. The same wafer displacement in such a system will result in a satisfactory image over a longer range, thereby increasing its depth of focus. An alt ernative to off-axis illumination is the Phase-Shift Mask (PSM) technology, which has been pioneered in recent years to extend the limits of optical lithography. PSM technology is divided into two categories: attenuated PSM and alternating PSM. Attenuated Phase Shift Masks (AttPSM) form their patterns through adjacent areas of quartz and , for example, molybdenum silicide (MoSi). Unlike chrome , MoSi allows a small percentage of the light to pass through (typically 6% or 18%). However, the thickness of the MoSi is chosen so that the transmitted light is 1800 out of phase with the light that passes through the neighboring clear quartz areas (figure 3.14) [11]. The light that passes through the MoSi areas is too weak to expose the resist, and its 1800 phase shift reduces the intensity in these areas such that they appear to be "darker" than similar features in chrome . The 113
result is a sharper intensity profile which allows smaller features to be printed on the wafer. The 1800 phase shift is only achieved for light at a given fixed wave length. At tPSM masks can t herefore only be used for one type of scanners only, while binary masks can be used for scanners with different wavelengths. MoSi feature phase c 180 transmiss ion is 6% reticle
quanz phase = 0" transmission = 100% chrome
phase (energy)
intensity (energy)
wafer
....... ... resist threshold
-"_....I..-~.L.....J..........---'-..........~L..-'--........._
remaining resist after develop
Figure 3.14: Basi c use of an at tenuated ph ase-shift m ask (at tP SM) (Source: ASML)
In fact , the use of attPSM filters one of the first order diffracted light beams of a three-beam imaging syst em (figure 3.12), which makes it a two-beam imaging syst em, similar to OAI imaging (figure 3.13). F igure 3.15 shows a comparison of the three different imaging systems. It clearly shows t he improvement of the DOF in the two-beam imaging syste ms.
114
aperture
aperture
reticle
:3 U
U
u
:3
:3
<2 .... +--*1-----,..... o
<2 -t---t-:f-.... o
E. 4J
E. 4J
..c +---,f+-' t t - - "0
..c -t----f-Jt--
-
"0
conventional illumination binary
<2 .... o
..c
+--+f'----
E. 4J
+--+-1.----- -
"0
conventional illumination phase shift reticle altPSM
ofT-axis illumination OAIand AuPSM
Figure 3.15: Comparison of the three different imaging systems (Source : ASML)
OAl systems and attenuated phase-shift masks are used for critical patterns that require higher resolution than photolithography systems that employ binary masks only. An alternative powerful but complex twobeam illumination system is the alternating phase-shift mask (altPSM) concept (figure 3.16). Such masks employ alternating areas of chrome, 0° phase quartz and 180° phase-shifted quartz to form features on the wafer [l1J. The pattern is etched into the quartz on the reticle causing a 180° phase shift compared to the unetched areas (0° phase). As the phase goes from positive to negative, it passes through O. The intensity (proportional to the square of the phase) also goes through 0, making a very dark and sharp line on the wafer. The process of manufacturing the mask is considerably more demanding and expensive than that for binary masks. Furthermore, the AltPSM requires an additional binary "trim" mask and exposure step, resulting in extra costs and decreased stepper/scanner throughput, however it enables excellent CD control. 115
reticle phase (energy)
+
intensity (energy')
wafer
chrome
.. ..
- - I ._
...................I..-.L-..l..........- . L.........................._
resisl threshold
'--
remaining resist af1er develop
Figure 3.16: Basic use of an alternating phase-shift mask (altPSM) (Source: ASML) AltPSM is used for the production of high-performance res that only allow extremely limited variations in line width, such as high-speed microprocessors. As explained, the above presented lithographic techniques are basically applied to increase the resolution and/or depth of focus of the total illumination system. Another technique, which is currently already applied to enhance the lithographic properties is called immersion lithography. If we immerse the photolithographic process in water (n = 1.43) and if we assume that sine in the expression (3.1) can reach a maximum value of 0.95, then this "water-immersion lithography" can yield an N A close to 1.37. Only the lower part of the optics is immersed in water (figure 3.17).
116
Figure 3.17: Basic principle of immersion lithography (Source: ASML) The left half in the figure shows the diffraction of the light beams in air, with a diffraction index n = 1 and some of the beams being reflected. The right halve uses an immersion liquid with n > 1, which reduces the amount of reflected light, increasing the resolving power and allowing finer feature sizes. Immersion lithography also improves the DOF, which may resolve some of the related topography problems. Compared to an air-based system, immersion lithography shows a number of additional problems. To achieve a high throughput, the stage has to step quickly from one chip position to the next, which may create bubbles into the water, deteriorating the imaging capability of the system. There are several solutions to this problem, but these are beyond the scope of this text . Using one of the above described resolution enhancement techniques (RETs) is a prerequisite to create lithographic images with a satisfactory resolution and DOF. But it is not sufficient. When printing patterns with sub-wavelength resolution they need to be compensated for the aberrations in the patterning. In other words: the fabricated IC patterns are no longer accurate replica of the originally designed patterns. So, we need already to compensate (make corrections) for these shortcomings in the mask. Figure 3.18 shows how optical proximity correction (Ope) is applied in the mask-definition process. The right mask pattern is used during lithography, to get left (original layout) pattern image on the chip . More optimal imaging results can be achieved by using socalled subresolution assist features (SRAFs) , such as scattering bars and hammerheads, which are not printed onto the wafer , but help to reduce resolution enhancement variations across the mask. 117
I I
rn
original pattern
II I
I
II
SRAFs
.,
~
II t,
rm
pattern after OPC
Figure 3.18: ope (including SRAFs) applied in the mask-definition process (Source: ASML)
This has several consequences for the layout designer: he should leave enough space to add OPC features and /or he should draw the patterns with constant proximity and/or he should leave enough space to add SRAFs. It will certainly make the design process more complex. While the above described RETs improve the resolution of the imaging system, the use of OPC masks will make them work. Mask costs , however, very much depend on the applied technology. When normalising the costs of a binary mask to 1, then an attPSM (without OPC) mask would cost 1.2 times as much and an attPSM (with OPC) mask 2.5 times. The use of altPSM is much more costly (6 times and 10 times more for altPSM without and with OPC , respectively), since it requires an additional binary trim mask and thus needs double exposure. For the time being, we still have to rely on innovations that extend the use of photolithography beyond the 40 nm node. Therefore suppor t from the design side might alleviate some of the expected problems when extending the use of 193 nm lithography into the sub 50 nm CMOS technologies. To improve yield, complex Design for Manufacturability (DfM) design rules have already been used in many technology nodes . For the 45 nm node this is certainly not enough. It will also require strict Design for Lithography (DEL) design rules. DfL, also called lithofriendly design , litho-driven design , or litho-centric DflVI , is focused on more regular layout structures. It will simplify the lithographic process , it supports SRAFs and might reduce the mask costs. It may also lead to a more aggressive scaling and to yield improvement due to a smaller variety of patterns to be printed. Moreover, more regularity in the 118
standard cells may also lead to a better portability to the next technology node. Figure 3.19 shows two layout versions of a standard cell: the original layout with a plot of simulated line widths and the litho-friendly layout with a plot of simulated line widths, showing more regularity.
•••••••
Figure 3.19: Comparison of an original (a) and a litho-friendly layout (b) with more regularity (Source: NXP Semiconductors)
For this particular cell, litho-friendly design shows a relatively large impact on the cell area. For an average library, however, the area increase can be limited to just a few percent. Next to the already discussed implications of RET and DfL for layout design, these techniques are increasingly being supported by the design flow and get more and more attention from Design for Yield (DfY) EDA-tools and tool vendors. An overview of EDA-vendor DfY activities is presented in [12]. Litho-friendly design usually uses a limited number of poly pitches. Such a fixed-pitch litho-friendly library design is a step towards a fullyregular library architecture. Next to the process spread caused by lithographic imperfections, such an architecture may also reduce the influence of other process-spread mechanisms, by using only one size NMOS and one size pMOS transistor. The high-density gate-array architecture shown in figure 7.34 is an example of such an architecture, which can also be used as standard-cell template. Before we continue our discussions, it is good to present some typical sizes and dimensions which are characteristic for a 45 nm CMOS process (table 3.1). It shows that there are different definitions for critical dimensions, feature sizes and pitches. They not only depend on the type 119
of circuit , but also on t he particular phase during the lith ographic and manufacturing process.
Ta ble 3.1: Various definitions for critical dimensions (CD), feature sizes (F), pitches and channel lengths (L, L eff ) depending on the lithographic and manufacturing process step and on the type of circuit, for a 45 nm process D im e n sio n pit ch litho print resist trim poly etch out diffusion
Low co st
180 65 = CD 50 45 = L = F 40 = Leff
LOGIC High performance
150 55-70 45 40 35
Stand-alone memory (excluding SRAM)
90 45 -
45 45
Let's summa rize t he individual cont ribut ions of the above-described RETs: t he combination of PSM and OP C may lead to a minimum k1 of about 0.25, while water immersion can lead to a maximum N A of ap proximately 1.37. Using these values, for a 193 nm lithography, in expression (3.1) for F , leads to a minimum feature size (= half pitch; most common for memories) of around 40 nm. Sma ller line widt hs, e.g., 30 nm , can be obtained, but wit h lar ger spa cings, e.g., 90 nm , at t he cost of addit iona l area . This will most commonly be used for the manufacture of logic ICs (ASICs) . It is t hus expected that the lifetime of 193 nm optical lithography can be exte nded for one or more technology nodes. Potenti ally, the feature size can be smaller by using a light-transpar ent liquid with a lar ger refraction index than water. It is clear that all addit iona l lithographic solut ions to enable sma ller feature sizes, will redu ce pat tern ab errations, bu t not pr event th em . Aft er reaching the limit s of 193 nm imm ersion lithography, so afte r the year 2010, 157 nm DUV (deep ultra violet )-line (from a fluorin e laser source) lithography could have been an opt ion. However , other imm ersion liquid s have to be explored (e.g., Fomblin oil), as the transparency of wate r is lost at wavelengt hs below 185 nm. According to to day 's knowledge, 193 nm lithography allows imm ersion liquids wit h a lar ger refracti on ind ex (n) t ha n t ha t of suitable liquid s in 157 nm imm ersion lith ography. This lat ter lith ography is expected 120
to only extend the lifetime of photolithography for one more technology node. Industry has therefore decided to skip the 157nm lithography because the development costs are not expected to be recovered. Below 157 nm optically transparent materials used for lens and mask will become increasingly absorbent. A potential work-around for this absorption problem would be to build a completely reflective optical system, but the reflection efficiency of even the best-polished optical devices is limited to only a few percent. Extreme-UV lithography, which will discussed below, uses reflective optics. Finally, particularly the semiconductor memory vendors have found a way to increase bit density without the use of very advanced and expensive lithography tools. By using multiple layers of silicon (3-D stacked silicon), memory capacity can be increased dramatically, without increasing the footprint of the memory chip. Some SRAM products use cells with three vertically stacked transistors, while some flash memories are currently being fabricated using two layers of memory cells. OTPs may be built from four layers already. NAND-flashes with eight layers of silicon are in development. 3-D technologies are currently only economically viable when the complexity of the devices fabricated in these stacked layers is very limited. Because non-volatile memories use only one type of transistor in the cells (see chapter 6) they are particularly suited for 3-D stacking. Therefore these layers are only used to fabricate arrays of memory cells and require only three masks per layer, which can be fabricated by existing photolithography tools. These arrays use the peripheral address selection and sense amplifier circuits of the original first memory array.
3.3.2
Lithographic alternatives beyond 40 nrn
Beyond 40 nm there are a couple of alternative solutions: • Use of an immersion liquid with higher refraction index, creating a so-called super-fluid NA in the range of 1.55 to 1.75. This would also require different lenses. • Use of a Double Patterning Technology (DPT). When the pitch of two lines in a dense pattern is less than 80 nm , it becomes a subresolution pitch, which can no longer be imaged correctly, with current lithographic techniques. Therefore this can be done with an image split: first image the odd lines with twice the minimum 121
feature pit ch (figure 3.20) and then image t he even lines, also with twice the pitch.
print target \ ith ub-re olution piteh
1 ..
.
r-
2p
....
~
first rna k• with double pitch pattern (uneven line) second mask. with double pitch pattern (even line)
2p
11111
final pattern. after rna k alignment and double expo urc
Figur e 3.20: Example of double pat terning
This pro cedure requires two masks and two exposures . The biggest challenge is the high accuracy of t he alignment of the masks during exposure . • Use of spacer lithography .
122
a
.......
print target with ub-resolution pitch
optical pitch
b
.....,
c spacer pitch ~
d
~r.~,~
'"
.__.":",
--',
-
spacer formaton
. . .-,- --silicon etch
pattern transfer into hardmask layer
e f
mask layout; poly ilicon pattern on hard rna k layer
. . . . . . . .....----I
final pattern on wafer
Figure 3.21: Basic steps in spacer lithography
In this technology the final pattern on the wafer is created by the formation of sub-resolution features during semiconductor process steps, rather than by sub-resolution lit hography. The process flow in this technology is as follows (figure 3.21). The print target is shown in (a). As a first step, a hard mask layer is deposited or grown on the wafer. To support the format ion of sub-resolution space rs a sacrificial polysilicon layer is deposited on the wafer and patterned with a relatively large optical lit hography pitch (b) . Next , an oxide (or nit ride or other) layer is deposited on top of the structure and then etched back until sub-resolution sidewall spacers are left (c). Then t he sacr ificial polysilicon is removed (etched) (d), followed by a pattern transfer from spacer to hard mask (e). Finally the pattern in the hard mask is used to create the final pattern on the wafer (f) . This spacer technology is a conve123
nient approach to achieve sub-resolut ion patternin g with relatively large optical resolut ion pitches, avoiding problems of e.g., overlay between successive exposures in a double patterning technology. Anot her advantage of t his technique is that the printed crit ical dimension uniformity (CDU) is independent of the line-edge roughness (LER). LER is caused by the diffusion ofresist during a heat ste p afte r t he exposure (post-exposure bake at 200-220°C), but before the development of the resist. This diffusion is rand om and may lead to diffusion length s of 40 nm, which causes int ra-line variations leading to frayed lines. In spacer technology, however, t he pat tern t ransfer is done t hrough spacers and not t hrough resists, showing almost no LER. A disadvantage of t he spacer lithography is that it is only ap plicable for mono CD (crit ical dim ension) which reflects t he smallest geomet rical features (cont acts, met al width, t renches, etc . which can be fabri cated), so, for pat terns with only one width. Pat terns with features t hat also have two t imes the line width can be produced by the format ion of two spacers directly positioned next to each other. For print ing patterns wit h different widths, DP T needs to be used. An example of nanofabrication spacer lithography can be found in [13] .
3.3.3
Next generation lithography
• Use of Extrcme-UV (EUV) lith ography. With a light source wave length of 13.5 nm, EUV is often regarded as the most probable pot enti al lithography solut ion for technology nodes beyond 30 nm. However , EUV " light" is absorbed by all materials, including air. T herefore mirrors have to be used in a vacuum-based system wit h reflective instead of refractive opt ics and reticles. St ill a lot of problems need to be solved before it can be used in high-volume productio n. A few of them will be mentioned here. First, there is no suitable resist for high-volume pro duct ion available, yet . Second, because the light needs to propagate t hrough a system of six to seven mirr ors, and one mirro r absorbs about 70% of t he light inte nsisty at t he EUV-wavelengt h, ext remely powerfull light sources are needed in combination with relatively long expos ure times. To generate 1 W of EUV power, t he RF power needed to act ivate t he plasma light source may be as high as 500 kW. T he lack of appropriate power sources and resists is a major bottleneck for bringing 124
t his lithography quickly to t he market . Thi s explains the need for an impr oved light-transmission system to impr ove t he t hroughput time and reduce t he power consumpt ion. In 2006 t he first EUV lith ography too ls (demo too l: US$ 65 million!!) have already been shipped. It is not meant for produ ction but it will suppo rt R&D programs at nvIEC (Leuven, Belgium) and at CNSE (University of Albany, New York) [14]. Produ ction EUV tools are not expected to ente r t he mar ket before 2010. • Use of alternative techniques to fabric ate image-crit ical pat terns in sub 30 nm technologies. For many years, X-ray lithography (X RL) has been a pot enti al candidate for next-generation lithography (NGL). It uses x-rays, which generate photons with a wavelength of roughly 1nm to expose the resist film deposited on the wafer, enabling much finer features t han current opt ical lith ography tools. However, it has some major disadvant ages. Convent ional lenses are unable to focus x-rays and, consequently, XRL too ls can not use a lens to shrink a mask's features. Th erefore its 1:1 pattern tra nsfer meth odology requires mask pat terns wit h only one-fourth of the feature sizes used in the 4:1 photo-lith ography masks. In addition, it requires an ext remely expensive synchrot ron, which converts an electro n beam into an x-ray beam. It is t herefore expected that the use of XRL will be limited to fabricat ion processes t hat create niche devices, such as MEMS. • An alternative to photolith ography is t he nano-imprint lith ography (NIL) , which may also be an opt ion for t he 32 nm node and/or beyond. T his 1:1 technology is based on physically pressing a hard mold (typically ident ical to the quartz / chrome material commonly used for opt ical lithography) with a pat tern of nano st ructures onto a thin blanket of t hermal plastic monomer or polymer resist layer on the sampl e subst ra te, to which th e st ruct ure needs to be replicated. Thi s impri ntin g ste p is usually done with th e resist heat ed, such th at it becomes liquid and can be deformed by t he pattern on t he mold. After cooling down, the mold is separated from the sample, which now contains a copy of the original pat tern. It s mayor advantage is that it can replicate features with nanometer dimensions [15] . T his process is already used in volume production in electrical, optical and biological applications. For semiconductor ap plicat ions, the "step-and-flash" imprint (SFIL) seems to be t he 125
most viable one. It allows imprinting at room temperature with only a little pressure using a low-viscosity UV curing solution instead of the resist layer. The higher the sensitivity to UV, the less exposure time the solution needs and the higher the throughput . In this imprint technology some of the wafer process complexity has moved to the fabrication of the mold. Still a lot of key issues, particularly related to overlay and defects, need to be solved, but the results of this disruptive technology, so far, are promising. A potential barrier for using the imprint lithography is that it requires very advanced lithographic processes to create the patterns on the mold. Because it is a 1:1 pattern transfer process , the pattern dimensions are only one-fourth of those printed on a photo mask, which is one of its major challenges. Moreover, low throughput may become the real show stopper for this technology. Reference [15] discusses the process and potentials of nano-irnprint in more detail. Moore's law is driven by the economical requirements of the semiconductor markets. This means that all semiconductor technologies (litho, diffusion, packaging , testing, etc.) are cost driven. For the lithography it means that there is a constant drive to make masks cheaper or to use cheaper masks for certain low-resolution process steps. Binary masks are relatively simple and cheap, but guarantee high throughput and can be non-destructively cleaned . Attenuated PSM masks are immersed in a chemical liquid for cleaning, which is a destructive process, such, that they can only be cleaned about three times and are therefore much more expensive . To minimise mask costs during the fabrication process, the more expensive masks are only used to image those patterns that really need the smallest feature sizes. For the production of one type of memory for example, different mask categories can be used. To reduce the production costs of a flash memory process of 22 masks, it may use 4 ArF (attPSM + OPC) masks , 12 KrF (6 binary and 6 attPSM) and 6 l-Iine (binary) masks.
3.3.4
Mask cost reduction techniques for low-volume production
On so-called multi-project wafers (MPW) several products are included on the same maskset to reduce overal mask costs (figure 3.22). 126
Figure 3.22: Example of a multi-project wafer (MPW) Another way to share the mask costs is the multi-layer reticle (MLR) , on which several mask layers of the same product are grouped together to reduce the physical number of masks. These MLRs do not combine designs of different products. Both techniques are particularly used for small-volume designs, for prototyping, and for educational purposes. To save mask costs completely, direct writing techniques use an electronbeam (e-beam) or laser-beam system, which writes the layout pattern directly onto a wafer resist layer , without using a mask. It requires the deposition of an additional conductive layer on the resist layer, to prevent damage by electron charging during the patterning process. The resolution yielded by an e-bearn machine is better than 5 nm , but at a lower throughput, because it writes every feature individually. It is free of wavelength aberration. Laser-beam systems are gaining market share at the cost of e-beam systems, because they are cheaper since they do not require a vacuum environment. Because of their low throughput, both 127
e-beam and laser-b eam systems usage, to day, is limited to fabricate lowvolume samples, such as MPWs, prototyping products and test silicon for process development . Next to t hat these techn iques are used to fabricate the physical glass-chrome masks (ret icles) for use in photolithography processes. These direct-writin g techniques are also called mask-less lith ography (MLL or ML2) and are curre ntly also being explored as an alternative for, or successor of the conventional photol ithogra phy, even for high volume prod uctio n. T he main reason is t he rapidly increasing costs of an optical mask set, which reaches the $2 million mark for the 65 nm node, although t hese costs will reduce when t he process is getting more mature . Over the last decade, a lot of progress has already been made to improve t hroughput. T he potentials of mask-less e-beam lithography are furt her discussed in [16]. More information on fut ure lit hography techniques can be found in numerous publicat ions and also on the internet and is beyond the scope of t his book. To summa rise t he evolution of the wafer stepper/scanner, table 3.2 presents several key parameters which reflect t he improvements made over different generations of ste ppers/scanners.
Table 3.2: The evolution of the wafer scanner (Source: ASML) Status @ 2007 of most-advance d litho-to ol s I-line DUV 193 Name Hg lamp KrF laser ArF laser Illu minat ion source 4x 4x 4x Reduction 248 193 nm 365 Wavelength 0.65 0.93 0.93 N A m a x projection lens 0.25 0.5 0.25 kL m i n 104 562 133 nm Minimum pitch 150 Depth of Focus Dense Lines 600 300 12 6 SMO 6 Overlay 20 MMO 10 10 4 10 6 nm Stage Repeatability 1.7 3.5 nm n.a. Lens distortion 8" /12" 8" /12" 8" / 12" inch Wafer size wph T hro ughput 165/135 165/ 135 150/122 13 19 5 Cost (MillionUS$)
128
193i ArF laser
4x 193 1.35 0.25 71 150 7 12 4 1.4 8" / 12" 165/122 > 36
EU' DPI
4x
13.E 0.2E
0.4 43 150 4 6 -
-
12" -
> 51
Pattern imaging The photolithographic steps involved in the transfer of a mask pattern to a wafer are explained with the aid of figure 3.23. Usually, the first step is oxidation and comprises the growth of a 30 to 50 nm thick silicondioxide (Si02) layer on the wafer. Subsequently, a nitride (Si3N4 ) layer is deposited (figure 3.23.a) . Next , this nitride layer is covered with a photoresist layer (3.23.b) . The mask is used to selectively expose the photoresist layer to light (3.23.c+d). The photoresist is then developed, which leads to th e removal of the exposed areas if the photoresist is positive. The resulting pattern in the resist after development (3.23.e) acts as an etch barrier in the subsequent nitride etching step (3.23.f), in which the unprotected nitride is removed (stripped). Finally, the remaining resist is removed and an image of the mask pattern remains in the nitride layer (3.23.g). This nitride pattern acts as a barrier for a subsequent processing step .
129
i3 4 (nitride) i 2 wafer + oxide (or nitride)
a
~~~~~~~~~~I - photo re i t layer b
c
coverage with photo lacquer
~~~~~~~~~~4_ mask t! rna king + expo ure expo ed photo resist
d
~~~~
expo ed photo re ist
development of the photo resist
e
etching of the nitride f
removal of the photo resist layer g)
Figure 3.23:
Pat t ern tra nsfer from mask to wafer
Both positive and negative resists exist . Th e differences in physical propert ies of thes e resist materials result in invert ing images, see figure 3.24. The combination of pattern transfer and one or more pro cessing st eps is repeated for all masks required to manufacture t he Ie. The types of layers used for t he pattern transfer may differ from the silicon-dioxide and silicon-nit ride layers described above.
130
r* 1 W
~"MI"'iIIi.!
__ exposed rcsi t positive resi t
nega~i\'c / rc
resist
sub trate
ISy
Figure 3.24: Th e use of positi ve and negative resist for pattern imaging The prin ciple, however , remains the same. The processing ste ps that follow pat tern transfer may comprise etching, oxidat ion, implant ation or diffusion and planarisation. Deposition is also an import ant pro cessing step. These ste ps are described in det ail in the following sect ions.
3.4
Etching
The previously described photolithographi c ste ps produce a pattern in a nitride or equivalent barri er layer. Thi s pattern acts as a protect ion while its image is duplic at ed on its und erlying layer by means of etching pro cesses. T here are several different etching t echniqu es. The etching pro cess must fulfil the following requir ements: a high degree of anisot ropy, good dimensional cont rol, a high etching rate to minimi ze processing t ime, a high selectivity for different materials, a perfect homogeneity and reprodu cabil ity (e.g., 1 billion trenches in a Gb DRA M) and a limit ed damage or contamination to sat isfy reliability standa rds. The degree of anisot ropy depends on t he requir ement s of the pro cess step, e.g., during t he STI etch an extremely vertical and sha rp profile 131
may increase st ress and t he occurrence of defects. With wet etching , t he wafer is immersed in a chemical etching liquid. The wet-etching methods are isotropic, i.e., t he etching rat e is t he same in all directions. The associated 'under-etch ' problem illustrated in figure 3.25(a) becomes serious when the minimum line width of t he etched layer approac hes its t hickness. rna k
layer ubstratc isotropic (a)
anisotropic (b)
Figure 3.25: T he results of different etching m eth ods Dry etching methods may consist of both physical and chemical processes (anisotropic) or of a chemical process only (isotro pic). Dry-et ching methods, which use a plasma, allow anisotropic etching, i.e., t he etching process is limit ed to one direction by t he perp endicular t rajectory of t he ions used at t he wafer sur face. The result , shown in figure 3.25(b), is an accurate copy of t he mask patt ern on the und erlying layer. With plasma etching techniques i17] , the wafers are immersed in a plasma cont aining chlorine or fluorine ions t hat etch, e.g., Al and Si02 respectively. It comprises a plasma cha mber, which contains a certain process gas. To transfer from the gas state into the plasma st ate, the chamber is pumped to the required pressur e and energy is supplied to produce a glow-discharge plasma by a radio frequency (RF) electromagnetic field. This causes ionisation of the low-temp erature plasma: aft er collision with molecules, they create many different gaseous species: free radicals, electrons, ions, neutrals, photons and by-products. These are then accelerated by an electrical field towards t he surface mat erial, which can then be etched quickly and selectively. The etching pro cess depends on the gas pressur e and flux and on t he applied RF field. In sputter etching techniques, the wafer is bombard ed by gas ions such as argon (Ar" ). As a result , the atoms at the wafer surface are physically dislodged and removed. 132
Finally, a combination of plasma and sputter etching techniques is used in Reactive Ion Etching (RIE). During RIE ionised gaseous molecules from the plasma are accelerated by an electric field toward the surface and react with the surface atoms forming new electrically neutral molecules which then floats away. Satisfactory etching processes have been developed for most materials that are currently used in IC manufacturing processes . New process generations, however, require improved selectivity, uniformity, reproducibility and process control. Selectivity can be improved by the compound of the gaseous plasma or by the creation of polymers at the underlying layer. The use of an additional carbonaceous substance such as CHF 3 during etching enhances its anisotropic properties. The use of this substance creates a thin layer close to the side wall of a contact hole, for example, which improves the anisotropy of the etching process . A second advantage is that carbon reacts with oxygen. It therefore increases the selectivity of the etching process because, when used in the etching of a contact-to-silicon, the reaction is stopped immediately on arrival at the silicon surface. Carbon does not react with silicon. For critical anisotropic etching steps, both low-pressure etching techniques and High-Density Plasma (HDP) techniques are used. In HDP, energy is coupled into the plasma inductively to increase the number of free electrons. HDP is operated at low (some mtorr) pressure. This in turn results in a higher plasma density and a higher degree of ionisation. HDP is used to provide high-aspect ratios. The focus on new etching techniques does not preclude further development of existing techniques such as high-pressure etching and RIE. Many process steps use plasma or sputter-etching techniques, in which charged particles are collected on conducting surface materials (polysilicon, metals) . Also during ion implantation, charge can be built up . These techniques can create significant electrical fields across the thin gate oxides; this is called the antenna effect . The gate oxide can be stressed to such an extend that it can be damaged (so-called process or plasma-induced damage: PID) and the transistor's reliability can no longer be guaranteed. The antenna effect can also cause a VT-shift, which affects matching of transistors in analog functions. It is industry practice to introduce additional "antenna design rules" to limit the ratio of antenna area to gate oxide area. There are different rules for polysilicon, contact, via and metal-antenna ratioes. These ratioes may vary e.g., from 10 (contact-on-poly area to poly-gate area) to 5000 (accumulated-
133
metal area to poly-gate area). Also, protection diodes are used to shunt the gate. Each input to a logic gate in a standard-cell library then contains a protection diode.
3.5
Oxidation
The dielectrics used in the manufacture of nanometer CMOS circuits must fulfil several important requirements [18]: • high breakdown voltage • low dielectric constant of inter metal dielectrics • high dielectric constant for gate dielectric • no built-in charge • good adhesion to other process materials • low defect density (no pinholes) • easy to be etched • permeable to hydrogen. One of the materials that incorporates most of these properties is silicon dioxide (Si02)' Si02 can be created by different processes: thermal oxidation or deposition. A thermal oxide was used to isolate the transistor areas in conventional MOS Ies. In these isolation areas , the oxide must be relatively thick to allow low capacitive values for signals (tracks) which cross these areas. This thick oxide was created by exposing the monocrystalline silicon substrate to pure oxygen or water vapour at a high temperature of 900°C to 1200°C. The oxygen and water vapour molecules can easily diffuse through the resulting silicon dioxide at these temperatures. The following respective chemical reactions occur when the oxygen and water vapour reach the silicon surface: Dry oxidation: Si (solid) Wet oxidation: Si (solid)
+ 02 (vapour) ---+ Si02 (solid) + 2H20 (vapour) ---+ Si02 (solid) + 2 H2
The Local Oxidation of Silicon (LOCOS) process is an oxidation technique which has found universal acceptance in MOS processes with gate 134
lengths down to 0.5/-Lm. Silicon is substantially consumed at the wafer surface during this process . The resulting silicon-dioxide layer extends about 46% below the original wafer surface and about 54% above it. The exact percentages are determined by the concentration of the oxide, which contains about 2.3 . 1022 atoms /em" , while silicon contains about 5 . 1022 atoms /em". A disadvantage of the LOCOS process is the associated rounded thick oxide edge. This bird '8 beak is shown in figure 3.26(a).
(b)
(a)
Figure 3.26: Comparison of (a) a conventional LOCOS process and (b) a new oxide formation process which yields a suppressed bird's beak
The formation of the bird 's beak causes a loss of geometric control, which becomes considerable as transistor sizes shrink. Intensive research efforts aimed at suppression of bird 's beak formation have resulted in lengths of just 0.1-0.15 usi: for an oxide thickness of 0.5 uui. Such a bird 's beak is shown in figure 3.26(b). Even with a suppressed bird 's beak , the use of LOCOS is limited to the isolation of over-0.25 /-Lm transistors. An important alternative to these LOCOS techniques, already used in 0.35/-Lm CMOS technologies and below, is the Shallow-Trench Isolation (STI) . STI uses deposited dielectrics to fill trenches which are etched in the silicon between active areas. The use of STI for nanometer technologies is discussed later in this chapter (section 3.9.3). Another important application of thermally grown oxide is the oxide layer between a transistor gate and the substrate in conventional CMOS processes. This 'gate oxide' must be of high quality and very reliable. 135
Defects such as pinholes and oxide charges have a negative effect on electrical performance and transistor lifetime. Because t he gate oxide is only a few atoms thick, it is particularly a challenge for t he indust ry to scale it further and/or find alternative ways to increase its capacitance. Figure 3.27 shows a cross sect ion of a MOS transistor. source
gale
drain
(bulk) ubstrate
Figure 3.27: Schematic cross section of a MO S transistor The gate-oxide thickness must be sufficient ly uniform across the die, die to die, wafer to wafer , and from run t o run . It scales with t he technology node according to t able 3.3, which shows representative values for various technology nodes. L represents t he physical gate length .
Table 3.3: Trends in gate-oxide thickness and threshold voltage Technology L [nm] t ox [nm] V dd [V] Vi [V] 3.3 0.6 350 7 0.35 /-t m 250 2.5 0.55 5 0.25 /-t m 180 3.2 1.8 0.55/0.45 0. 18 /-t m 120 2 1.2 0.45/0 .35/0.2 0. 13 /-t m 90nm 80 2.2/1.6 1.2/1. 0 0.45/0.4/0.35/0. 3/0.2 65nm 60 1.8/1.2 1.2/1.0 0.5/0.4/0 .3/0.2 45nm 40 1.1/ 0.9 1.8/1 0.5/0.4/0 .3/0.1 The table also shows the divergence in gate oxide thicknesses, supply and threshold voltages. This is du e to t he fact that today's semiconducto r t echnologies must support applicat ions with a wide range of performance requirements: high-density, low act ive power, low standby power , high 136
speed , etc . In each technology node, the input- and output (I/O) transistors usually operate at a larger voltage (1.8 V, 2.5 V and/or 3.3 V) and require an additional oxide thickness and threshold voltage. The simultaneous use of more oxide thicknesses and threshold voltages in one process is of course at the cost of more mask , lithograhpy and processing steps. Technology nodes , today, offer different process versions , e.g., a general-purpose (GP) process and a low-leakage (LL) , also called low-standby power (LSTP) , process. Each of the processes offers usually only two or three different threshold voltages, to limit the number of masks , lithography and processing st eps. The use of dielectric Si0 2 layers below about 2 nm thickness causes gate oxide direct tunnelling , resulting in currents which may exceed a level of 1 A/cm 2 . At th ese gat e-oxide thicknesses, pMOS transistors with heavily boron-doped polysilicon suffer from boron penetration into the gate oxide, causing an undesirable positive threshold-voltage shift and a performance and reliability degradation. The quality of the gate oxide is greatly improved with nitrided gate oxide. It reduces boron pen etration and improves gate oxide charge-to-breakdown [19]. On the other hand, too much nitrogen close to the gate-oxide/Si-substrate interface enhances Negative Bias Temperature Instability (NBTI; see also chapter 9) [20]. Moreover , the combination of thinner gate oxide and increased channel doping also causes depletion of t he bottom region of the gat e material and this effect becomes more pronounced with further scaling of the oxide thickness. This is called gate depletion. As a result of these effects, the current ly-used double-fl avoured polysilicon (n ! dop ed gate for nMOS transistors and p+ doped gate for pMOS transistors) is most likely to be replaced by a met al. Other alternat ives, which are currently und er research and also prevent gat e depletion, include fully-silicid ed (PUSI) polysilicon gates. Most advanc ed CMOS processes use at omic-layer deposition (ALD) to fabricat e the very thin gat e-oxide layer. This is discussed in the next subsection.
3.6
Deposition
The deposition of thin layers of dielectrical material, polysilicon and met al is an important aspe ct of IC production. The growth of an epitaxial film (layer) is the result of a deposition step combined with a chemical reaction between the deposited and substrate material. If the deposited layer is the sam e mat erial as the substrate, it 137
is called homo-epitaxy or epi-layer for short. Silicon on sapphire is an example of hetero-epitaxy, in which the deposited and substrate materials differ [21]. Epitaxial deposition is created by a Chemical Vapour Deposition (CVD) process. This is a process during which vapour-phase reactants are transported to and react with the substrate surface, thereby creating a film and some by-products. These by-products are then removed from the surface. Normally, the actual film created by a CVD process is the result of a sequence of chemical reactions. However, a different overall reaction can generally be given for each of the silicon sources . The hydrogen reduction of silicon tetrachloride (SiCI4), for example, can be represented as: SiCl4 + 2H2 ----+ Si
+ 4 HCI
Several parameters determine the growth rate of a film, including the source material and deposition temperature. Usually, high temperatures (> 1000°C) are used for the depositions because the growth rate is then less dependent on the temperature and thus shows fewer thickness variations. The overall reaction for the deposition of polysilicon is: SiH4 (vapour)
----+
Si (solid)
+ 2 H2 (vapour)
This reaction can take place at lower temperatures, because SiH4 decomposes at a higher rate. The creation of dielectric layers during IC manufacture is also performed by some form of CVD process. The most commonly-used dielectric materials are silicon dioxide (Si02) and silicon nitride (SbN 4). In an Atmospheric-Pressure CVD (APCVD) process, the material is deposited by gas-phase reactions. This deposition generally results in overhangs and a poor step coverage (figure 3.29). APCVD is currently used to deposit Boron PhosphoSilicate Glass (BPS G) epitaxial layers and form the scratch-protection layer (PSG). BPSG is a dielectric which is deposited on top of polysilicon (between polysilicon and first metal). BPSG contains boron and phosphorus for a better flow (spread) of the dielectric. The phosphorus also serves to improve internal passivation. The following reactions apply for the deposition of Si02 and Si3N4, respectively: LPCVD: PECVD: LPCVD:
Si(OC 2H5)4 Si(OC 2H5)4 3SiChH2
----+
+ 02 ----+ + 4NH3 ----+
138
Si0 2 + by-products Si0 2 + by-products Si3N4 + 6HCL + 6H2
Two versions of CVD have been introduced by the above reactions: LP CVD and P ECVD. LP CVD is a low-pressur e CVD process, usually performed in a vacuum chamber at medium vacuum (0.25-2.0 torr) and at tem peratures between 550 and 750 "C. Under t hese conditions, t he vapour-phase reactions are suppressed, while the decomposition now occurs at t he surface , leading to a much bet ter step coverage . In the previously-discussed CVD process, t he chemical reacti ons are initi ated and sustained only by t hermal energy. PECVD is a plasma-enhanced CVD process. A plasma is defined to be a part ially ionised gas which contains ions, electrons and neutrals. T he plasma is generated by applying an RF field to a low-pressur e gas, t hereby creating free electrons within t he discharge regions [21]. The electrons gain sufficient energy so t hat they collide with gas molecules, t hereby causing gas-phase dissociat ion and ionisation of the reactant gases. At room temperature, a plasma therefore already contains high-energy electrons. Thus, even at low temperat ures, a PECVD process can generate reactive particles; it t herefore has a higher deposition rate tha n ot her CVD processes. If we compare t he previous reactions to depositin g Si02, we see t hat t he LP CVD which occurs at high te mperature t herefore needs no additional oxygen, while t he P ECVD process needs addit ional oxygen because t he oxygen cannot be dissociat ed from the TE GS (tetra et hylorthosilicat e: Si(OC2Hs )4) at low te mperatures . A Sub-Atmospheric CVD (SACVD) process occurs at temperatures around 700 to 800 "C. Because of t he high pressure (:::::; 1/2 atmosphere instead of a few torr) , t he deposition speed will be higher , resulting in a higher t hroughput . T his form of CVD is part icularly used for BP SG. Metal layers are deposited by both physical and chemical methods. In Physical Vapour Deposition (PVD) methods, such as evaporation and sputtering, the material is physically moved onto t he subst ra te . PVDEvaporation is a deposition process, in which a vap our of t he mat erial to be deposited is tra nsported to the wafer in a low-pressure environment. After condensation at t he wafer surface, it forms a thin film on it. Wh en using t he PVD- spu t tering t echnique for the deposition of aluminium, for inst ance, an aluminium target is bombarded with argon ions, which physically dislodge aluminium molecules from the target, causing a flux of aluminium to flow from the target to t he wafer surface. The aluminium was alloyed with 0.5% copper to improve elct romigrat ion behaviour. After deposition of t he aluminium phot olitho graphi c and etching ste ps are used to create t he required metal patt ern. 139
Copp er cannot be deposit ed and etched as easy as aluminium. Potent ial etching plasmas create non-volatil e residuals that remain on the wafer. Moreover , Copp er defuses through oxides leadin g to t ra nsistor threshold volt age shifts and reliability probl ems. Therefore, a copper back-end technology is quite different from a convent ional aluminium one. In the latter , t he aluminium deposition ste p is followed by a dry etching step to etch t he met al away accordin g to the mask pat tern and then filling t he gaps with a dielect ric. A copper back-end uses a socalled damascene process flow, in which the convent iona l subt ractive met al etching pro cess flow is replaced by a met al inlay process flow. Figure 3.28 shows a comparison of both flows. conventional
damascene
___l~,---__ ILD
photoresist patterning
photoresist patterning
- - _L...J- - -i dry etching of metal
oxide etching + barrier deposition
oxide deposition
copper deposition
r-----'-'----CMP + barrier coverage
Figure 3.28: Comparison of convent ional and damascene processing In a damascene process, first trenches are etched in t he inter-level dielectric (ILD) layer , most commonly an oxide layer. Then a t hin barrier layer is deposited by an atomic layer deposition (ALD) ste p on top of the ILD layer and prevent s the diffusion of copper. Next , a seed layer is deposited to provide a conduct ive layer , which is requir ed for t he electroplate-deposition process of t he copper, to improve copper adhesion and coverage . T hen, copper deposition is done, using an electro-
140
chemical process: elect roplating, in which t he wafer is immersed in a (salt/acid) solut ion of copper sulfate (and some ot her acids and/or additives to enhance t he filling capabilities) and connected to a negative terminal of t he power supply. T he positive supply te rminal is connected to a copper body, which creates copper ions into the salt solut ion. These positively charged copper ions are attracted to t he negative wafer surface and form a t hick copper blanket across t he total wafer. Then a planarisation ste p, called CMP (sect ion 3.8) polishes t he wafer until it has reached t he bot tom of the barrier layer (copper and barri er are removed in one ste p!). Copper tracks are then remainin g as a met al inlay in the t renches (Damascene processing), similar to t he met al inlay in swords, made in ancient t imes in Damascus, Syria. Then again a barri er layer is deposited t o cover t he top of the copper inlays, such that copper is fully enca psulated within the barrier mat erial. Today, most fabs use a dual-damascene backend , in which both t he vias (also called st uds, or pillars, which are contacts between two metal layers) and t renches are simultaneously etched int o the ILD layer. Also in t he next sequence of deposition ste ps for t he barr ier, the seed layer and t he electro plate copper, respectively, t he vias and tracks are simultaneously filled, t hereby reducing processing costs. Alt hough t he resist ance of copper is 40% less tha n that of aluminium , this advantage can not fully be exploited , beca use part of t he available track volume is occupied by the barrier material, which has a much higher resist ance value. The use of copper instead of aluminium for interconnection resulted in only a limited reduction of t he effect ive inte rconnect resist ivity by 25 to 30%. In combination with t he use of low-E dielectri cs, t he int erconnect capacitance is reduced and leads to faster or less-power circuits. Copper can also withst and higher current densities, resulting in a reduced chance of elect romigration (see chapte r 9). CVD methods form the chemical altern ative for the deposition of met als. Tungsten (W) , for example, may yield the following CVD react ion:
WF6 + 3H2 ---t W
+ 6HF
The choice of deposition method is determined by a numb er of factors, of which step coverage is the most imp ortant . Figure 3.29 shows an example of bad aluminium ste p coverage on a contact hole in a conventional CMOS process. Such a ste p coverage can dramatically reduce the lifetime of an IC. It also causes problems duri ng further processing 141
steps and the associated temperature varia tions can lead to voids in the aluminium. Moreover , t he local narrowings cannot withstand high current densities. Current densities of:::::: 105 A/ cm 2 are not except ional in mod ern int egrated circuits. Excessive current densities in metal tracks cause electromigration. This leads to the physical destruction of metal tracks and is another phenomenon that reduces the reliability of lCs . This topic is examined more closely in chapter 9.
Figure 3.29: Example of poor step coverage in a convention al CMOS process
One depo sition step that got a lot of atte nt ion over the last decade is the so called atomic layer deposition (ALD) , particularly for its potential applications in advanced (high-E) gate dielectrics, DRAM capacitor dielectrics and copper diffusion barriers in advanced CMOS and memory pro cesses. Without going deep into the chemical and physical reactions, ALD basically uses pulses of gas, creating one atomic layer at a t ime. So, the deposited film thickness is only dep endent on the numb er of deposition cycles providing extremely high uniformity and thickness control. It is therefore also of int erest in all (sub) nanom et er applicat ions that benefit from accurate control of (ultra-) thin films. More details on ALD can be found in [22] .
3.7
Diffusion and ion implantation
Diffusion and ion implant ation are the two most commonly-used methods to force impurities or dopants into the silicon.
142
Diffusion Diffusion is the process by which the impurities are sprea d as a result of t he exist ing gradient in the concent rat ion of t he chemical. Diffusion is oft en a two-st ep pro cess. The first st ep is called pre-deposition and comprises t he deposition of a high concent ration of t he required impurity. The impuriti es penetrate some tent hs of a microm eter into the silicon, genera lly at temperatures between 700 to 900°C . Assum ing t hat t he impurities flow in one direct ion, t hen t he flux is expressed as:
J = - D . 8C(x , t ) 8x where D represent s the diffusion coefficient of the impurity in [cm 2 / s] and ~~ is the impurity concent rat ion gradient . As t he diffusion strongly depends on te mperature, each different diffusion process requires individua l calibration for different pro cessing conditions. During t he diffusion process , silicon atoms in the lat t ice are then substit ute d by impurity atoms. The second step is called drive-in diffusion. This high-t emp erature (> 1000 °C) ste p decreases t he surface impurity concentration, forces t he impurity deeper int o the wafer , creat es a better homogeneous distribution of the impurities and activates the dopants. This driv e-in diffusion also causes an ident ical lat eral diffusion. As a result of t he increased requirements of accurate doping and doping profiles, diffusion techniques are losing favour and ion impl ant ation has become t he most popul ar method for introducing impuriti es into silicon. Ion Implantation The ion imp lantation pro cess is quite different from the diffusion pro cess. It takes place in an ion implanter , which comprises a vacuum chamber and an ion source t hat can supply phosphoru s, arsenic or boron ions, for example. The silicon wafers are placed in the vacuum cha mber and t he ions are accelerated towards t he silicon under the influence of elect ric and magnetic fields. The penetration depth in the silicon depend s on the ion energy. This is determined by t he mass and electrica l cha rge of t he ion and the value of the accelerat ing voltage. Ion imp lanters are 143
equipped with a mass spectromete r (analysing magnet ), which ensures t hat only ions of t he correct mass and charge can reach t he silicon wafer. Ion implantation is characterised by the following four parameters: • T he type of ion. Generally, t his is phosphorus, arsenic or boron. T he mass and electrical charge of t he ion are import ant. • The accelerating voltage (V), which varies from a few kilovolt to hundreds of kilovolts. • The curre nt strengt h (1), which lies between O. l J1A and 1mA. • T he implant ation dur ation (t), which is in the order of tens of seconds per wafer. The total charge Q = I . t det ermin es t he numb er of ions that will ente r the silicon. Typical doses range from 1011_1016 ato rns/crrr'. Variables V , I and t can be measur ed with very high accuracy. This makes ion implantation much more reproducible for doping silicon t han classical diffusion techniques. In addition, V and I can be varied as a funct ion of t to produ ce a large variety of doping profiles that are not possible with diffusion. The maximum impurity concentration is almost always at t he surface when diffusion techniques are used. T he ion implant at ion technique, however, can be used to selectively create profiles with peaks below t he wafer surface. T he concentration of impurities decreases toward the wafer surface in these 'retrograde profiles'. The most import ant material t hat is used to mask ion implantin g is photoresist . Ion implantation causes serious damage (disorder) in t he crystal lat t ice of t he target. In addition, only a fraction of the implanted ions occupies a silicon ato m location. The ot her part does not occupy lattice sites. The interstitial dope at oms are electr ically inactive and do not opera te as donors or acceptors. A subsequent t hermal ste p, at te mperatures between 800 to 1000°C, is used to recover the crystal struc t ure . The intention of thi s annealing process is to cause t he vast majority of t he dopants to become electrically act ive on t he lat t ice sites . Ion implant at ion adds flexibility and increased process contr ol to CMOS manufacture. It is superior to chemical deposition techniques for t he cont rol of impurities ranging from 1014 to 1021 ato ms/em". The heart of an ion implanter is formed by an ion source , usually an RFactivate d plasma, from which ions are ext racted by a small electric field, and a 90° analysing magnet. Because t he ion beam is a mixture of different fractions of molecules and ato ms of t he source material, t he 90° 144
analysing magnet causes only t he selected ions, wit h exactly the right charge and mass, t hat face equal cent rifugal and cent ripetal forces, to reach t he wafer t hrough t he accelerator column and the resolving aperture , see figure 3.30 and [23] . Lighter ions st rike the inner wall; heavier ions st rike the out er wall. beam guide analy ing magnet
~
too
hcavy
accelerator column
wa cr
Figure 3.30: Schematic drawing of an ion implanter Examples of t he use of ion implant ation are: • threshold voltage adjustment (e.g., 1 . 1018 - 5 . 1018 ato ms /c m' , however t his leads to a stee p retrograde dope profile, in which the surface (channel) dope concent ration is between 1 . 1017 and 5. 1017 atoms /c m'' : see table 3.3 for t he different t hreshold volt ages t hat are current ly applied in the different technology nodes.) • retrograd e-well implant at ion • channel-st op implantation • source/dra in format ion (0.15-0.4fLm shallow regions) • etc . Non-ideal aspects of ion implantation: • lateral distribution of impurities is not complete ly zero 145
• throughput is lower t han in diffusion process • complex and expensive implant ers • initial cost of equipment : 2 t o 5 M$. The use of ion implant at ion in t he format ion of source/dra in regions becomes increasingly challenging as these junctions become very shallow in scaled proc esses. The dopin g concent rat ion does not increase with scaling. Only t he energy during implantat ion must be adjusted to create thos e shallow junctions. Silicidation of sources and drains becomes a probl em in that silicide can penetrate through the shallow junction s. This is called junction spiking . Unsilicided sources and drains show a five to ten times higher sheet and cont act resistance, affecting the electrical properties of the transistors. Because of thi s, all modern CMOS pro cesses today use silicided sources and dr ains.
3.8
Planarisation
The increase in t he numb er of processing ste ps, combined with a decrease in feature sizes, results in an increasingly uneven surface. For example: afte r complet ing t he tra nsisto rs, an isolation layer is deposited before t he metal layers are deposited and patterned. The ste p height of t he und erlying surface is replicated int o this isolation layer. This int roduces two potential probl ems in t he fabri cation process. When t he first met al is directly deposited onto t his layer , its t hickness can dramatically reduce at these ste ps, causing an increase in met al resistance and an increase in the occurrence of electromigrat ion. Secondly, as already discussed in the lithography section, new litho graphy tools allow a smaller depth-of-fo cus (DOF), tolerating only very small height variations. During imaging, these variations can introduce focus probl ems at the high and low areas. Therefore, all current CMOS processes use several planarisation steps. These steps flatten or 'planarise' the surface before the next processing ste p is performed. In convent ional CMOS pro cesses, planarisation was used during t he back-end of the process, i.e., in between t he formation of successive met al layers t o flatten the surface before the next metal layer was defined. In such a Spin -On-Glass (SOG) formation, t he surface was coated with a liquid at room te mperature . After t his, t he wafer was rot ated (spun) , such that the liquid flowed all over t he wafer to equalise t he surface. 146
Next, the wafer undergoes a high-temperature curing process to form a hard silicate or siloxane film. To prevent cracking , phosphorus was often incorporated in the film. The resulting dielectric layer was planarised to a certain extent. An advantage of SaG is that very small gaps are easy to fill. However, with SaG, the surface is locally, but not globally, planarised, see figure 3.31. On locally rough areas (A and B), the surface is reasonably planarised. A
B
'...._---
,'-----------.
- - - -
Figure 3.31: SOG planarisation results There is still a global height difference after SaG planarisation, depending on the local pattern densities (area A, B and C). In a multilevel metal chip, this effect would be much worse and would lead to etching problems and problems with the DOF of the stepper. In all CMOS technologies below O.25/-Lm, a very good alternative planarisation technique is used: Chemical Mechanical Polishing (CMP) . CMP is based on the combination of mechanical action and the simultaneous use of a chemical liquid (slurry) and actually polishes the surface, see figure 3.32.
147
down force
wafer
(device up ide down}--1:=========:::::::t poli hing pad rotating poli hing table
F igur e 3.32: Schematic overview of the eM? polishing process The slurry contains polishing par ticles (e.g., silica or alumina) and an etching substance (KOH or NH40 H (e.g. , ammonia)) . A polishing pad together wit h t he slurry plan arises the wafer surface . Because CMP is also base d on a mechanical action, it is much better suited for the local and globa l plan arisation of roug h areas , by offering a reduced to pography for a more consiste nt focus across the field of expos ure . It is par t icularly used for t he creation and oxide filling of trenches (ST I; sect ion 3.9.3) and during t he met allisation (bac k-end) par t of a multi-l ayer met al process. From t he pr evious text the reader might conclude t hat CMP lead s to an ideal planarisation result. However, there are severa l issues related to differences in pattern densities and differences in polishing rates of th e various mat erials. Figur e 3.33 shows t he polishing results at three different phases of the CMP process.
148
initial wafer topography with different pattern densities
wafer topography after intermediate poli hing pha c
final wafer topography aftcr
MP completed
Figure 3.33: Changing wafer topography after different CMP polishing phases
The forces, exhibited during the polishing process, cause a higher pressure on the individual features in sparsely dense areas than in high dense areas. As a result, an increased polishing rate is observed on areas with very sparse patterns, compared to areas with the high-density patterns. This may lead to problems with the DOF during the lithography process and to reliability problems because of different contact heights.
dishing
erosion
I
Figure 3.34: Potential problems of copper CMP As discussed in section 3.6, the copper CMP process includes the simultaneous removal of copper and barrier. The soft center of relatively large copper areas (wide copper lines and pads) polishes faster than the barrier/dielectric interface. This so-called dishing effect (figure 3.34) increases the resistance of these lines and reduces pad reliability. Also due to the difference in polishing rates, areas with dense copper patterns will polish faster than areas with only sparse copper patterns. This so-called
149
erosion will also lead to thinner copper lines with higher resistance. These polishing problems, in combination with the increased porosity of the inter-metal dielectrics, require constant monitoring through test structures for maintaining or improving both yield and reliability. Particularly the mechanical degradation of the pads may lead to problems as cracking and peeling-off during packaging . Measures to prevent planarisation problems in the back-end metallisation process include the creation of dummy metal patterns in scarcelyfilled areas. The idea is to create metal patterns with as uniform a density as possible . These dummy metal patterns, sometimes also called tiles, should be automatically defined during chip finishing. Figure 3.35 shows an example of the use of tiling to achieve an improved metal distribution for optimised planarisation.
Figure 3.35: Improved homogenous metal distribution by the use of tiles (purple)
150
The use of tiles improves the quality of global planarisation and also results in a better charge distribution (reduced antenna effect) during back-end processing (deposition and etching of the successive metal layers). The shape of the individual tiles should be chosen such that it hardly affects the yield, performance, and signal integrity of a logic block. A disadvantage of CMP is the mechanical wear of the polishing pad. As a result , the speed of polishing is reduced and, sometimes after each wafer, a diamond-brush step is performed to recondition the pad. After about 500 wafers, the polishing pad must be completely replaced. Figure 3.36 shows the result of the CMP planarisation technique in a multi-metal layer process.
151
Figure 3.36: Cross sections of CMOS back end, showing the pot entials of CMP planarisation (Source: NXP Semiconductors)
152
3.9
Basic MOS technologies
Sections 3.3 to 3.8 illustrate t hat MOS processes mainly consist of severa l basic act ions t hat are repeated. In modern CMOS processes , the total numbe r of act ions has increased to several hundreds. In t his sect ion, a basic nMOS process with just five masks is discussed. A good underst anding of t his silicon-gate nMO S process enables a smooth tra nsit ion to t he complex modern CMOS processes. With t he exception of some new ste ps, t hese CMOS processes are just an exte nsion of t he basic nMOS process presented here. A good insight into both technology ty pes is a prerequisite when comparing t he advantages and disadvant ages of nMOS and CMOS. Fina lly, a nanometer CMOS process is presented and t he associated fund amentally new ste ps are discussed. The section is concluded with a quantitative discussion of CMOS technology opt ions beyond 45 nm.
3.9.1
The basic silicon-gate nMOS process
An nMOS process which uses a mere five masks is explained with the aid of figure 3.37. First, an oxide is grown on t he base silicon wafer. Next , t he oxidised silicon wafer is coated with a silicon nitride (Si3N4 ) layer , as shown in figure 3.37(a) . The first mask is the ACT IVE mask , which is used to define nitride areas corresponding to subst rate regions where transistors should be formed . Aft er t he nit ride is etched , boron is implanted t hrough t he resulting holes to produ ce t he channel stopper, discussed in section 1.8 and indicated in figure 3.37(b). The wafer is t hen oxidised to produce t he LOCOS areas in figur e 3.37(c). The result ing thick oxide only exists at places that were not covered by t he nitride. T he channel st opper is t hus auto matically present everywhere beneath t he LOCOS oxide. Thi s is a great advantage of t he LOCOS process. The removal of the remainin g nitride reveals the areas in which t ransistors will be created. Now, the oxide is removed by a wet HF dip . The next ste p is the growth of a t hin oxide in t hese areas. The thickness of t his oxide varies from a few to a few tens of nanometers in most MOS processes. T he t hreshold voltage adjust ment implantation which follows t his oxidation damages t he t hin oxide. The implantation is therefore done through t his sacrificial pad oxide . Low-energy impurity atoms such as iron (Fe) and/or copper (Cu) from t he ion implanter may be caught in and/or masked by t he sacri ficial gate oxide
153
during the implantation. This sacrificial pad oxide is subsequently removed and the actual thin gate oxide is grown. In some processes , however, impurities are implanted through the sacrificial pad oxide, e.g., during a threshold voltage (correction) implant. The properties of a MOS transistor are largely determined by the gate oxide. Gate oxidation is therefore one of the most critical processing steps. Its thickness is between 1 and 7 nm (see table 3.3). After this, a polysilicon layer of about 0.1 to 0.4 /Lm thickness is deposited. A subsequent phosphorus diffusion, used to dope the polysilicon, is followed by photolithographic and etching steps, which yield polysilicon of the required pattern on the wafer. The POLY mask is the second mask step in this process and is used to define the pattern in the polysilicon layer. This step corresponds to figure 3.37(d) . The polysilicon is used both as MOS transistor gate material, where it lies on thin oxide, and as an interconnection layer, where it lies on thick oxide (LOCOS) . The sheet resistance of polysilicon interconnections lies between 20 and 3000/0. Polysilicon can therefore only be used for very short interconnections (inside library cells). Phosphorus (P) or arsenic (As) are mainly used to create the source and drain areas. The sheet resistance of these areas is about the same as that of polysilicon. Today's polysilicon source and drain areas are silicided to reduce the resistance values to about 50D /D (see section 3.9.3). The edges of the n+ areas are defined by the LOCOS and the polysilicon gate. Source and drain areas are thus not defined by a mask but are self-aligned , according to the location of the gate. The overlap of the gate on the source and drain areas is therefore determined by the lateral diffusion of the source and drain under the gate. In the nMOS processes that used diffusion to create sources and drains, the length of the lateral diffusion is about 60% of the diffusion depth of the drain and source. Currently, lower doped thin drain extensions are used which show a lateral diffusion of about 40% of their depth, see also section 3.9.3. With a drain extension of 20 nm , the lateral diffusion is only about 8 nm in a 45 nm process . The effective transistor channel length is therefore equal to the polysilicon width minus twice the lateral diffusion. The wafer is then covered with a new oxide layer, deposited by an LPCVD step. The resulting SILOX layer indicated in figure 3.37(e) is about 300 to 800 nm thick. The CONTACT mask is the third mask step in this process and is used to define contact holes in the SILOX layer, see also figure 3.37(e). The metal layer is then deposited by means of 154
sputtering, see sect ion 3.6. T he METAL mask is the four th mask in t his sam ple process. It is used to define t he pattern in the aluminium or t ungsten layer. Basically, the processing is now completed, see figure 3.37(f). However , as a final ste p, the entire wafer is covered wit h a plasma-nitride passivation layer. This scratch -protection layer protects the integrat ed circuit from external influences. Figure 3.37(f) shows the sit uation before deposition of t he scratch protection. With a final mask ste p, t he scratch protection is etched away at t he bonding pad positions to be able to make wiring connect ions from the chip to t he package. This mask and the associated processing ste ps are not includ ed in the figure. In summary, t he mask sequence for t he considered basic silicon-gate nMOS proc ess is as follows: 1. ACTIVE
2. POLY 3. CONTACT 4. METAL
definition of act ive areas polysilicon pat t ern definition definition of contact holes between aluminium and monocrystalline silicon or polysilicon interconnection pat tern definition in aluminium.
Finally, the NIT RIDE mask is used to etch open ings in t he nitride passivatio n layer , to be ab le to connect bond ing pads with package leads. Note: T he tem peratures used for the source and drain diffusion exceed 900°C. Aluminium evaporates at t hese temperatures . Self-aligned source/drain formation is t herefore impossible in an aluminium-gate process. Molybdenum gates have also been exper imented wit h. However , t hey have never been industrially applied. In current CMOS technologies t he sources and drains are implante d rather than diffused, due to the very high accuracy of t he channel length definition.
The silicon-gate nMO S process has the following propert ies: • Small gat e-source and gate-drain overlap capacitances, caused by t he self-aligned implant ations . • A relatively low numb er of masks, i.e., basica lly five to six. • Three interconnection layers, i.e., n+ diffusion, polysilicon and aluminium. However , intersections of n+ and ·polysilicon interconnect ions are not possible as these result in t he formation of a t ransistor. Chapter 4 presents a basic summary on t he prop erties of nMOS circuits.
155
(a)
T
silicon nitride
I
SiD,
boron implant
(b) "--
polysilicon
'-J~~~~~_!!!!!III. ===:=::~ ~+t=======1 La as
(c)
-
channel stopper ---' implant
I
p-
p
----J
Mask layout - .1----_._-_. Active mask
phosphorus or ar enic
_ ! /-----
(d)
Active ilox
(e)
----I
L...-
metal
(f) Figure 3.37: The basic silicon-gate nMOS process with LOCOS isolation
156
(a) definition of isolation areas (active areas as well)
(b) formation of the LOCOS isolation (alternative: shallow trench isolation)
L
n-well
':::J"
Si02
(c) formation of the well(s) (retrograde)
(d) - definition and etching of polysilicon - source and drain implants for nMOS and pMOS transistors
(e) -
silox deposition contact etching metal definition finally: formation of passivation layer
Figure 3.38: The basic CMOS process with LOCOS isolation
157
3.9.2
The basic Complementary MOS (CMOS) process
CMOS circuits and technologies are more complex than their nMOS counterparts. In addition, a static CMOS circuit contains more transistors than its nMOS equivalent and occupies a larger area in the same process generation. However, CMOS circuits dissipate less power than their nMOS equivalents. This is an important consideration when circuit complexity is limited by the 1W maximum power dissipation associated with cheap plastic IC packages. In fact, reduced dissipation is the main reason for using CMOS instead of nMOS. Both n-type and p-type transistors are integrated in CMOS processes. Figure 3.38 illustrates the flow of a simple CMOS process with an n-well , or n-tub, in which the pMOS transistors are implemented. This process serves as an example for the many existing CMOS technologies. The basic CMOS process begins with the oxidation, to some tens of nanometers, of a monocrystalline p-type silicon wafer. A layer of silicon nitride (Si3N4) is then deposited on the wafer. This is followed by a photoresist layer. A mask is used to produce a pattern in the photoresist layer corresponding to active areas. Circuit elements will be created in these areas. The defined pattern determines which silicon nitride remains during a subsequent etching step. The photoresist is then completely removed , as shown in figure 3.38(a). LOCOS oxide is then grown by exposing the wafer to oxygen at a high temperature. This oxide will not be grown on the areas that are still covered by the nitride. The LOCOS oxide separates active areas, see figure 3.38(b) for an indication of the result. Instead of LOCOS , STI is used in deep-submicron and nanometer CMOS processes to separate active areas (see next subsection). A new photoresist layer is then deposited and the p-type transistor areas are 'opened' during photolithographic steps. In convent ional processes , the n-well was created by depositing a high concentration of donors (mostly phosphorous) in these areas, as shown in figure 3.38(c). Initially, these ions collect at the silicon surface but they diffuse more deeply during a subsequent high temperature step. Today, the n-well (and p-well) are implanted (see next subsection) . A layer of polysilicon is then deposited on the wafer, which now consists of n-type n-well areas with a limited submicrometer depth and p-type substrate areas. Polysilicon doping reveals either n-type polysilicon for both nMOS and pMOS transistor gates, or double-flavoured polysilicon (n-type and p-type polysilicon for nMOS and pMOS transistor gates , respectively) . 158
Thi s is also sometim es referred to as n" /p+ dual polysilicon. A photolithograph ic ste p follows and t he polysilicon pat tern is etched. The resulting polysilicon is used for short interconnections and for t ra nsistor gates . Separate masks are used for t he self-aligned source/drain implantations: nplus and pplus for t he nMOS and pMOS tra nsisto rs in t he subst rate and n-well, respectively. The result is shown in figure 3.38(d). The first step in t he creation of interconnections between t he different tra nsistor areas is to deposit an Si02 (SILOX) layer on t he wafer. Cont act holes are etched in thi s layer to allow connect ions to the gates , dr ains and sources of the tra nsisto rs. A metal layer is t hen deposited , in which the final interconnect pattern is created by means of photolithogra phic and etching st eps. Figure 3.38(e) shows t he final result . Modern CMOS processes use 25 to 35 masks. Basically, these processes are all extensions of the simple CMOS process described above. VLSI and memory processes now use channel (gate ) lengths of 45 nm to 0.35 J.Lm and offer several levels of polysilicon and /or metal. These multipl e interconnection layers facilitate higher circuit densities. The next sect ion discusses a state-of-t he-art nanometer CMOS process.
159
3.9.3
An advanced nanometer CMOS process
nitride pa si ation layer
tung tcn contact plug TI
rctrogrndc n-wcll
Figure 3.39: An advanced nanometer process with ST I isolation Compared to the basic CMOS process discussed before, an advanced nanomet er CMOS process, with channel lengths below 100nm , incorporates several major different processing steps. These differences will now be discussed in some det ail.
Shallow-trench isolation Actually, LOCOS is t hick Si0 2 t hat is thermally grown between t he act ive areas . In contrast, Shallow- Trench Isolation (STI) is implemented at significant ly lower tem peratures, prevent ing many warpage and stress problems associated with a high-t emperature ste p. T he STI process starts wit h a t hermally-grown oxide with a t hickness between 10 nm to 14 nm . T his is followed by an LP CVD deposition of 100 nm to 160 nm 160
nitride. Next , the active areas are masked and a dry etch step is applied to create the trenches, which have a typical depth between 250 nm and 500 nm. The corners at the bottom and the top of the trench are rounded by a thermally-grown oxide layer (between 20 nm and 50 nm) along the side walls of the trench, see figure 3.40.
Figure 3.40: Cross-section after etching the trenches in the silicon After removing the resist, a thick oxide High-Density Plasma (HDP), typically 700 nm to 1100 nm, is deposited. HDP is capable of filling the high asp ect ratio of the trenches, which includes the pad oxide and nitride layer thicknesses. As shown in figure 3.41, the step coverage of the oxide is dependent on the geometry of the active area mask.
161
c V Spot 00 IN 3 0
~ a9n
~ OO O OX
wo
t:xp 10 '1 3
WGJ 929 13' 16
bOO nm lIt:>d Hor oXldo
Figur e 3.41: STI process cross-section after thi ck oxide deposition In dense areas, the oxide level is well above the silicon nitride, while the oxide t hickness equals the deposited oxide t hickness in large open areas. The remainin g topology is planarised using CMP , see section 3.8. The nitride layer is used as chemical etch stop, see figure 3.42.
Figure 3.42: SEM cross-section after eMP 162
Next, the nitride masking layer is removed, using a wet etch and subsequently sacrificial oxide, gate oxide (by ALD) and polysilicon is deposited, etc. Figure 3.43 shows a cross-section through the width of the device. The gate oxide between the polysilicon layer and the monocrystalline silicon substrate can be as thin as 1 nm in very advanced nanometer CMOS ICs.
Figure 3.43: TEM cross-section through the width of the device In this way, device widths far below 100 nm can be well defined. Figure 3.44 shows a comparison between LOCOS and STI field isolation techniques. It is clear that the STI is much more accurately defined and enables the creation of high aspect-ratio field-oxide isolation areas to improve the circuit density in nanometer CMOS ICs.
163
Figure 3.44: Comparison between LOCOS (top) and STI field isolation (bottom) techniques
Retrograde-well formation
A retrograde-well process (figure 3.39) uses both n-wells and p-wells, and is also called a twin-well process . These wells form the substrate for p-type and n-type devices, respectively. High-energy implantation of the wells yields doping profiles with maxima between 250 and 6