Air Pollution Modeling and Its Application XVIII
Previous Volumes in this Mini-Series Volumes I–XII were included in the NATO Challenges of Modern Society Series. AIR POLLUTION MODELING AND ITS APPLICATION I Edited by C. De Wispelaere AIR POLLUTION MODELING AND ITS APPLICATION II Edited by C. De Wispelaere AIR POLLUTION MODELING AND ITS APPLICATION III Edited by C. De Wispelaere AIR POLLUTION MODELING AND ITS APPLICATION IV Edited by C. De Wispelaere AIR POLLUTION MODELING AND ITS APPLICATION V Edited by C. De Wispelaere, Francis A. Schiermeier, and Noor V. Gillani AIR POLLUTION MODELING AND ITS APPLICATION VI Edited by Han van Dop AIR POLLUTION MODELING AND ITS APPLICATION VII Edited by Han van Dop AIR POLLUTION MODELING AND ITS APPLICATION VIII Edited by Han van Dop and Douw G. Steyn AIR POLLUTION MODELING AND ITS APPLICATION IX Edited by Han van Dop and George Kallos AIR POLLUTION MODELING AND ITS APPLICATION X Edited by Sven-Erik Gryning and Milla´n M. Milla´n AIR POLLUTION MODELING AND ITS APPLICATION XI Edited by Sven-Erik Gryning and Francis A. Schiermeier AIR POLLUTION MODELING AND ITS APPLICATION XII Edited by Sven-Erik Gryning and Nadine Chaumerliac AIR POLLUTION MODELING AND ITS APPLICATION XIII Edited by Sven-Erik Gryning and Ekaterina Batchvarova AIR POLLUTION MODELING AND ITS APPLICATION XIV Edited by Sven-Erik Gryning and Francis A. Schiermeier AIR POLLUTION MODELING AND ITS APPLICATION XV Edited by Carlos Borrego and Guy Schayes AIR POLLUTION MODELING AND ITS APPLICATION XVI Edited by Carlos Borrego and Selahattin Incecik AIR POLLUTION MODELING AND ITS APPLICATION XVII Edited by Carlos Borrego and Ann-Lise Norman
Air Pollution Modeling and Its Application XVIII
Edited by Carlos Borrego University of Aveiro Aveiro, Portugal Eberhard Renner Leibniz-Institute for Tropospheric Research Leipzig, Germany
Amsterdam – Boston – Heidelberg – London – New York – Oxford Paris – San Diego – San Francisco – Singapore – Sydney – Tokyo
Elsevier Radarweg 29, PO Box 211, 1000 AE Amsterdam, The Netherlands Linacre House, Jordan Hill, Oxford OX2 8DP, UK First edition 2007 Copyright r 2007 Elsevier Ltd. All rights reserved No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher Permissions may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone (+44) (0) 1865 843830; fax (+44) (0) 1865 853333; email:
[email protected]. Alternatively you can submit your request online by visiting the Elsevier web site at http://www.elsevier.com/locate/permissions, and selecting Obtaining permission to use Elsevier material Notice No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein. Because of rapid advances in the medical sciences, in particular, independent verification of diagnoses and drug dosages should be made Library of Congress Cataloging-in-Publication Data A catalog record for this book is available from the Library of Congress British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library ISBN: 978-0-444-52987-9 ISSN: 1474-8177 For information on all Elsevier publications visit our website at books.elsevier.com
Printed and bound in Italy 07 08 09 10 11 10 9 8 7 6 5 4 3 2 1
v
Contents
List of participants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The members of the scientific committee for the 28th NATO/ CCMS international technical meeting on air pollution modeling and its application . . . . . . . . . . . . . . . . . . . . . . History of NATO/CCMS air pollution pilot studies . . . . . . . Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . xvii
. . . xxxiii . . . xxxv . . xxxvii
Section 1: Local and urban scale modelling 1.1.
Application and validation of FLUENT flow and dispersion modelling within complex geometries Silvana Di Sabatino, Riccardo Buccolieri, Beatrice Pulvirenti and Rex Britter . . . . . . . . . . . . . . . . . . . . 3
1.2.
Turbulence, atmospheric dispersion and mixing height in the urban area, recent experimental findings Sven-Erik Gryning and Ekaterina Batchvarova . . . . . . . . . . 12
1.3.
Inverse modelling of local surface emissions with the CHIMERE-adjoint model: The case of the Paris area during the ESQUIF field experiment L. Menut, I. Pison and N. Blond . . . . . . . . . . . . . . . . . . . . 21
1.4.
Numerical simulations of microscale urban flow using the RAMS model Tamir Reisin, Orit Altaratz Stollar and Silvia Trini Castelli . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
1.5.
Assessment of dust forecast errors by using lidar measurements over Rome P. Kishcha, P. Alpert, A. Shtivelman, S. O. Krichak, J. H. Joseph, G. Kallos, P. Katsafados, C. Spyrou, G. P. Gobbi, F. Barnaba, S. Nickovic, C. Perez and J. M. Baldasano . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Contents
vi
1.6.
Modelling urban heat island in the context of a Mediterranean city F. Santese, S. Di Sabatino, E. Solazzo and R. Britter . . . . . 55
1.7.
Evaluation of land surface scheme modifications on atmospheric transport and deposition patterns in Copenhagen metropolitan area Alexander Mahura, Alexander Baklanov, Steen Hoe, Jens H. Sorensen, Claus Petersen and Kai Sattler . . . . . . . . 64
Section 2. Regional and intercontinental modelling 2.1.
Modelling of secondary aerosols in Switzerland in summer 2003 S. Andreani–Aksoyoglu, J. Keller, A.S.H. Prevot, U. Baltensperger and J. Flemming . . . . . . . . . . . . . . . . . . . 75
2.2.
Application of the CMAQ mercury model for U.S. EPA regulatory support O. Russell Bullock Jr. and Thomas Braverman . . . . . . . . . . 85
2.3.
Multi-objective analysis to control ozone exposure Claudio Carnevale, Giovanna Finzi, Enrico Pisoni and Marialuisa Volta . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
2.4.
Atmo-rhenA: a common air quality modelling system in the Upper Rhine Valley R. Deprost, J. Bernard, E. Riviere, N. Leclerc and C. Schillinger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
2.5.
Perturbational downscaling and its applications in air pollution and meteorological problems Eugene Genikhovich and Guy Schayes . . . . . . . . . . . . . . . 123
2.6.
Increase in nitrate deposition as a result of sulfur dioxide emission increase in Asia: Indirect acidification Mizuo Kajino and Hiromasa Ueda . . . . . . . . . . . . . . . . . 134
2.7.
Predicted aerosol concentrations over East Asia and evaluation of relative contribution of various sources with global chemical transport model T. Kitada, Y. Shirakawa, K. Wagatani, G. Kurata and K. Yamamoto . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Contents
vii
2.8.
Long-term simulations of photo-oxidants and particulate matter over Europe with emphasis on North Rhine-Westphalia M. Memmesheimer, S. Wurzler, E. Friese, H. J. Jakobs, H. Feldmann, A. Ebel, C. Kessler, J. Geiger, U. Hartmann, A. Brandt, U. Pfeffer and H.P. Dorn . . . . . . . . . . . . . . . . . . . . . . . . 158
2.9.
Developing and implementing an updated chlorine chemistry into the community multiscale air quality model Golam Sarwar, Deborah Luecken and Greg Yarwood . . . . 168
2.10. Modeling assessment of the impact of nitrogen oxides emission reductions on ozone air quality in the Eastern United States: Offsetting increases in energy use P. Steven Porter, Edith Ge´go, Alice Gilliland, Christian Hogrefe, James Godowitch and S. Trivikrama Rao.. . . . . . . . . . . . . . . . . . . . . . . . . . 177 2.11. Dispersion modelling of the concentrations of the fine particulate matter in Europe Mikhail Sofiev, Erwan Jourden, Liisa Pirjola, Leena Kangas, Niko Karvosenoja, Ari Karppinen and Jaakko Kukkonen . . . . . . . . . . . . . . . . . . . . . . . . . . 189 2.12. The use of meteorological and dispersion models in stratified atmospheric boundary layers M. R. Soler, M. Bravo and S. Ortega . . . . . . . . . . . . . . . . 200 2.13. Modelling regional air quality over decades: Past and future trends in photochemical smog Robert Vautard, Sophie Szopa, Matthias Beekmann, Laurent Menut, Didier A. Hauglustaine and Laurence Rouil. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 210 2.14. Forecasting ozone PM2.5 in southeastern U.S. M. Talat Odman, Yongtao Hu, Michael E. Chang and Armistead G. Russell . . . . . . . . . . . . . . . . . . . . . . . . 220 2.15. Integrated observational and modelling approaches for evaluating the effectiveness of ozone control policies J. Godowitch, A. Gilliland, E. Gego, R. Draxler and S. Trivikrama Rao . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Contents
viii
2.16. Medium-range puff growth Torben Mikkelsen, Søren Thykier-Nielsen and Steen Hoe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 243 2.17. Operational evaluation of the Eastern Texas air quality (ETAQ) forecasting system based on MM5/SMOKE/CMAQ Daewon W. Byun, Meong-Do Jang, Chang-Keun Song, Soontae Kim, Fang-Yi Cheng, Ryan Perna and Hyun-CHeol Kim. . . . . . . . . . . . . . . . . . . . . . . . . . . 253 Section 3. Data assimilation and air quality forecasting 3.1.
Improvement in particles (PM10) urban air quality mapping interpolation using remote sensing data Nuno Grosso, Francisco Ferreira and Sandra Mesquita . . . 265
3.2.
The use of ensemble weather forecast for dispersion uncertainty modelling Lennart Robertson, Andrew Jones, Francois Bonnardot and Stefano Galmarini . . . . . . . . . . . 275
3.3.
Forward and inverse modelling of radioactive pollutants dispersion after Chernobyl accident Mikhail Sofiev, Ilkka Valkama, Carl Fortelius and Pilvi Siljamo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
3.4.
PREV’AIR: A platform for air quality monitoring and forecasting C. Honore´, L. Menut, B. Bessagnet, F. Meleux, L. Rouı¨ l, R. Vautard, N. Poisson and V. H. Peuch . . . . . . . . . . . . . 293
3.5.
Estimation of sulphur emissions using ensemble smoothers Alina L. Barbu, Remus G. Hanea, Arnold W. Heemink, Martijn Schaap and Pierre Girardeau. . . . . . . . . . . . . . . . 301
3.6
Application of a four-dimensional variational (4DVAR) data assimilation for optimal estimation of mineral dust and CO emissions in eastern Asia Keiya Yumimoto and Itsushi Uno . . . . . . . . . . . . . . . . . . 318
Section 4: Model assessment and verification 4.0.
A review of uncertainty and sensitivity analyses of atmospheric transport and dispersion models Steven R. Hanna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
Contents
ix
4.1.
Lagrangian particle model simulation of tracer dispersion in stable low wind speed conditions D. Anfossi, S. Alessandrini, S. Trini Castelli, E. Ferrero, D. Oettl and G. Degrazia . . . . . . . . . . . . . . . . 352
4.2.
Application and sensitivity analysis of CAMx and CHIMERE air quality models in a coastal area Isabelle Coll, Guido Pirovano, Fanny Lasry, Stefano Alessandrini, Marco Bedogni, Matteo Costa, Veronica Gabusi, Laurent Menut and Robert Vautard . . . 362
4.3.
A comparison between CHIMERE, CAMx and CMAQ air quality modelling systems to predict ozone maxima during the 2003 episode in Europe: Spain case study R. San Jose´, J. L. Pe´rez and R.M. Gonza´lez . . . . . . . . . . . 374
4.4.
Final results of the model inter-comparison of very high-resolution simulations with numerical weather prediction models for eight urban air pollution episodes in four European cities B. Fay, L. Neunha¨userer, A. Baklanov, G. Bonafe´, S. Jongen, J. Kukkonen, V. Ødegaard, J. L. Palau, G. Perez-Landa, M. Rantama¨ki, A. Rasmussen, R. S. Sokhi and Y. Yu . . . . . . . . . . . . . . . . . . . . . . . . . . 383
4.5.
Uncertainty in air pollution models used for regulatory and risk assessment purposes Bernard Fisher and Robert Willows . . . . . . . . . . . . . . . . . 395
4.6.
Aerosol mass budget analysis over Berlin city area by means of the CTM REM_Calgrid Andreas Kerschbaumer, Matthias Beekmann and Eberhard Reimer . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
4.7.
The use of CFD and mesoscale air quality modelling systems for urban applications: Madrid case study R. San Jose´, J. L. Pe´rez and R.M. Gonza´lez . . . . . . . . . . . 416
4.8.
Modelling the dynamics of air pollutants over the Iberian Peninsula under typical meteorological situations P. Jime´nez, O. Jorba and J.M. Baldasano . . . . . . . . . . . . . 425
Contents
x
4.9.
Modelling of the July 10 STERAO storm with the RAMS model: Chemical species redistribution including gas phase and aqueous phase chemistry Maud Leriche, Sylvie Cautenet, Mary Barth and Nadine Chaumerliac . . . . . . . . . . . . . . . . . . . . . . . . . 437
4.10. A study of process contributions to ozone formation during the 2004 ICARTT period using the Eta-CMAQ forecast model over the northeastern U.S. Shaocai Yu, Rohit Mathur, Kenneth Schere, Daiwen Kang, Jonathan Pleim, Jeffrey Young and Tanya Otte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 447 4.11. Validation of the integrated RAMS-Hg modelling system Antigoni Voudouri and George Kallos . . . . . . . . . . . . . . . 457 4.12. Analyzing the response of a chemical transport model to emissions reductions utilizing various grid resolutions Rainer Stern, Robert J. Yamartino and Arno Graff. . . . . . 467 Section 5: Aerosols in the atmosphere 5.1. Modelling of pollen dispersion with a weather forecast modelsystem H. Vogel, B. Vogel and Ch. Kottmeier . . . . . . . . . . . . . . . 481 5.2. Aerosol forecast over the Great Lakes for a February 2005 episode Pius Lee, Jeffery McQueen, Marina Tsidulko, Mary Hart, Shobha Kondragunta, Daiwen Kang, Geoff DiMego and Paula Davidson . . . . . . . . . . . . . . . . . 492 5.3. On the contribution of the heterogeneous chemistry to nitrate concentrations over Europe based on modelling results and long-term and campaign measurements Alma Hodzic, Laurent Menut, Bertrand Bessagnet and Robert Vautard . . . . . . . . . . . . . . . . . . . . . . . . . . . . 503 5.4. Modelling seasonal changes of aerosol compositions over Belgium and Europe Felix Deutsch, Filip Lefebre, Liliane Janssen, Jean Vankerkom and Clemens Mensink . . . . . . . . . . . . . . 514
Contents
5.5.
xi
Modelling of Saharan dust events within SAMUM: Implications for regional radiation balance and mesoscale circulation Ju¨rgen Helmert, Bernd Heinold, Ina Tegen, Olaf Hellmuth and Ralf Wolke . . . . . . . . . . . . . . . . . . . . 523
5.6. Long-term aerosol simulation for Portugal using the CHIMERE model C. Borrego, A. Monteiro, J. Ferreira, A. I. Miranda, R. Vautard and A. T. Perez. . . . . . . . . . . . . . . . . . . . . . . 534 5.7. Radiative effects of natural PMs on photochemical processes in the Mediterranean Region Marina Astitha, George Kallos, Petros Katsafados, Ioannis Pytharoulis and Nikos Mihalopoulos . . . . . . . . . . 548 5.8. Modelling of mineral dust emissions and transport with CHIMERE-DUST model: Preliminary analysis of dust events for the AMMA field campaign L. Menut, C. Schmechtig, R. Vautard and B. Marticorena . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 560 5.9. Comparison of modelled and measured aerosol optical depth over southwestern Germany R. Rinke, D. Ba¨umer, B. Vogel, St. Versick and Ch. Kottmeier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 568 5.10. On the direct aerosol forcing of nitrate over Europe: Simulations with the new LOTOS-EUROS model Martijn Schaap, Ferd Sauter and Peter Builtjes . . . . . . . . . 582 5.11. Causes for spread between global models w.r.t. Lifetime and distribution of particulate sulphate Øyvind Seland and Trond Iversen . . . . . . . . . . . . . . . . . . 592 5.12. Modelling of aerosol composition using the MARS/MUSE dispersion model A. Arvanitis, E. Debry, I. Douros and N. Moussiopoulos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 601 5.13. Interpretation of new particle formation bursts in the planetary boundary layer using a high-order columnar model Olaf Hellmuth. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610
Contents
xii
5.14. Mixing of plumes with ambient background air: Effects of particle size variations close to the source T. Engelke, A. Hugo, E. Renner, F. Schmidt, R. Wolke and J. Zoboki . . . . . . . . . . . . . . . . . . . . . . . . . 621
Section 6: Interactions between climate change and air quality 6.1.
Examining the impact of changing climate on regional air quality over the U. S. Ellen J. Cooter, Robert Gilliam, William Benjey, Chris Nolte, Jenise Swall and Alice Gilliland. . . . . . . . . . . 633
6.2.
Analyzing the impacts of climate change on ozone and particulate matter with tracer species, process analysis, and multiple regional climate scenarios C. Hogrefe, D. Werth, R. Avissar, B. Lynn, C. Rosenzweig, R. Goldberg, J. Rosenthal, K. Knowlton and P.L. Kinney. . . . . . . . . . . . . . . . . . . . . 648
6.3.
Dimethylsulphide (DMS) flux and DMS oxidation over the North Atlantic: Comparison of a top-down & bottom-up approach A.L. Norman, M.A. Wadleigh, S. Eaton, C. Burridge, C. Zaganescu, J.P. Blanchet, M. Scarratt, S. Michaud, M. Levasseur, A. Merzouk, M. Lizotte, S. Sharma and R. Leaitch . . . . . . . . . . . . . . . . . . . . . . . . 661
Section 7: Air quality and human health 7.1.
Calculations of personal exposure to particulate matter in urban areas Inga Fløisand, Herdis Laupsa, David Broday, Trond Bøhler, Werner Holla¨nder, Susanne Lu¨tzenkirchen, Christos Housiadas, Thanos Stubos and Harold McInnes . 679
7.2.
Lagrangian particle model simulation to assess air quality along the Brenner transit corridor through the Alps D. Oettl, P. Sturm, D. Anfossi, S. Trini Castelli, P. Lercher, G. Tinarelli and T. Pittini. . . . . . . . . . . . . . . . 689
7.3.
Optimum exposure fields for epidemiology and health forecasting Bill Physick, Martin Cope, Sunhee Lee and Peter Hurley . . 698
Contents
xiii
7.4.
On influence of long-range transport of pollen grains onto pollinating seasons Pilvi Siljamo, Mikhail Sofiev, Elena Severova, Hanna Ranta and Svetlana Polevova . . . . . . . . . . . . . . . . 708
7.5.
Air quality characterization for environmental public health tracking Timothy Watkins, Fred Dimmick, David Holland, Alice Gilliland, Vickie Boothe, Chris Paulu and Andrew Smith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 717
Section 8: Poster session 1.
Mass flux balance at an urban intersection Sandro Baldi, Matteo Carpentieri and Alan G. Robins . . . 731
2.
Wind tunnel experiments of flow and dispersion in idealised urban areas Matteo Carpentieri, Andrea Corti and Paolo Giambini . . . 734
3.
Improving the Martilli’s urban boundary layer scheme: Off-line validation over different urban surfaces R. Hamdi and G. Schayes . . . . . . . . . . . . . . . . . . . . . . . . 737
4.
Wind shear distortion of concentration fluctuations from an elevated source Trevor Hilderman and David J. Wilson . . . . . . . . . . . . . . 740
5.
Inter-comparison of CFD, wind tunnel and Gaussian plume models for estimating dispersion from a complex industrial site P. Jenkinson, R. Hill, E. Lutman, A. Arnott and T.G. Parker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 742
6.
Nowcasting and forecasting the street pollution dispersion for Tallinn metropolitan area Marko Kaasik, Triinu Lukk, Kuido Kartau and Tanel Dovnar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 744
7.
Wind-driven NOx removal by flow-through fences with ACF (Activated Carbon Fiber): Evaluation of the fence’s efficiency in reduction of ambient NOx Toshihiro Kitada, Makoto Nagano, Takaaki Shimohara and Takayuki Tokairin . . . . . . . . . . . 747
Contents
xiv
8.
Radiative transfers in CFD modelling of the urban canopy Maya Milliez, Luc Musson-Genon and Bertrand Carissimo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 750
9.
Evaluation of passive pollutants residence time in a deep street canyon by CFD simulations F. Murena and G. Favale . . . . . . . . . . . . . . . . . . . . . . . . 754
10. Modelling integrated system for urban air quality in Bologna Linda Passoni, Vanes Poluzzi, Marco Deserti, Enrico Minguzzi, Michele Stortini and Giovanni Bonafe` . . 758 11. Long-term evaluation of secondary atmospheric pollution over Italy M. P. Costa, S. Alessandrini, M. bedogni, B. Bessagnet, E. Bossi, G. Maffeis, C. Pertot, G. Pirovano and R. Vautard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 761 12. Modelling past and future trends in sulphur and nitrogen deposition in the United Kingdom A. J. Dore, M. B"as´ , M. Kryza, J. Hall, C. J. Dore, M. Vieno, K. J. Weston and M. A. Sutton . . . . . . . . . . . . 764 13. Long-term simulation and validation of ozone and aerosol in the Po Valley M. Stortini, M. Deserti, G. Bonafe and E. Minguzzi . . . . . 768 14. Biogenic emission modelling in Lithuania Vidmantas Ulevicius, Vytautas Vebra, Kestutis Senuta and Kristina Plauskaite . . . . . . . . . . . . . . . . . . . . . . . . . . 771 15. The use of a photochemical trajectory model to estimate pollution levels within the West Midlands conurbation, UK Helen L. Walker, Jacob Baker, Richard G. Derwent and Rossa G. Donovan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 774 16. Producing high-resolution spatial maps of ambient ozone concentrations in Belgium Stijn Janssen, Jef Hooyberghs, Clemens Mensink, Gerwin Dumont and Frans Fierens . . . . . . . . . . . . . . . . . 784 17. 2D variational data assimilation of near-surface chemical species Lennart Robertson and Michael Kahnert . . . . . . . . . . . . . 787
Contents
xv
18. Principal component and multiple linear regressions to predict ozone concentrations Sofia I. V. Sousa, Fernando G. Martins, Jose´ C. M. Pires, Maria C. M. Alvim-Ferraz and Maria C. Pereira . . . . . . . 790 19. Relationships between nitrogen oxide emissions from electrical generating units in the U.S. and Meteorology P. Steven Porter, S.T. Rao and E.L. Gego . . . . . . . . . . . . 793 20. Validation of the meteorological input for air quality simulations in Northern Italy Giovanni Bonafe`, Marco Deserti, Suzanne Jongen, Enrico Minguzzi and Michele Stortini . . . . . . . . . . . . . . . 795 21. The North American mercury model inter-comparison study (NAMMIS) O. Russell Bullock, Dwight Atkinson, Thomas Braverman, Ashu Dastoor, Didier Davignon, Noelle Selin, Daniel Jacoby, Kristen Lohman, Christian Seigneur, Krish Vijayaraghavan, Tom Myers, Kevin Civerolo and Christian Hogrefe. . . . . . . . . . . . . . . . . . . . . . . . . . . 798 22. Two-dimensional steady state advection-diffusion equation: An analytical solution Daniela Buske, Marco Tullio Vilhena, Davidson Moreira and Tiziano Tirabassi . . . . . . . . . . . . . . . . . . . . . 802 23. The new GIADMT approach to simulate the pollutant dispersion in the planetary boundary layer Camila Costa, Marco Tullio Vilhena, Davidson Moreira and Tiziano Tirabassi . . . . . . . . . . . . . . . . . . . . . 805 24. One-dimensional eddy diffusivities for growing turbulence in the convective boundary layer Antonio Goulart, Umberto Rizza, Davidson Moreira, Marco T. Vilhena, Gerva´sio Degrazia and Jonas Carvalho. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 808 25. Impact of meteorological factors on turbulent dispersion over complex terrain S. Saavedra, J. A. Souto and J. Vila`-Guerau de Arellano . . 811 26. An air pollution model applying a semi-analytical solution for low wind conditions Tiziano Tirabassi, Davidson Moreira, Daniela Buske and Antoˆnio Goulart . . . . . . . . . . . . . . . . 814
xvi
Contents
27. Modeling of Saharan dust events within SAMUM: On the description of the Saharan dust cycle using LM-MUSCAT Bernd Heinold, Ju¨rgen Helmert, Ina Tegen, Olaf Hellmuth and Ralf Wolke . . . . . . . . . . . . . . . . . . . . . . . . 817 28. An improved coupling scheme in the parallel modelling system LM-MUSCAT R. Wolke, M. Lieber, B. Heinold, J. Helmert, W. Schro¨der and E. Renner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 820 29. Identification of aerosol sources in the Baikal region by receptor modeling methods Ekaterina V. Kuchmenko, Elena V. Molozhnikova, Alexandre V. Keiko and Maxim S. Zarodnyuk . . . . . . . . . 823 30. Small-scale modeling of PM deposition and re-suspension in inner part of urban area Jiri Pospisil and Miroslav Jicha . . . . . . . . . . . . . . . . . . . . 826 31. Enhanced characterization of ambient air quality to study the link between climate variability, air quality, and health C. Hogrefe, K. Knowlton, R. Goldberg, J. Rosenthal, C. Rosenzweig, B. Lynn and P.L. Kinney . . . . . . . . . . . . . 829 32. Preparatory work for optimised European air quality and health effect monitoring (EURAQHEM) T. Kuhlbusch, A. John, U. Quass, A. Hugo, A. Peters, S. von Klot, J. Cyrys and E. Wichmann . . . . . . . . . . . . . . 832 33. PM levels and their health implications in Lisbon Hugo Tente, Francisco Ferreira, Luı´ sa Nogueira, Carlos Silva Santos and Sandra Moreira. . . . . . . . . . . . . . 835 34. Spatial and temporal variation in particulate Polycyclic Aromatic Hydrocarbons (PAH) levels Menen (Belgium) and their relation with air mass trajectories Khaiwal Ravindra, Eric Wauters and Rene´ Van Grieken . . 838 Author Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 843 Subject Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 865
xvii
List of participants
The 28th NATO/CCMS International Technical Meeting on Air Pollution Modeling and Its Application, Leipzig, Germany, May 15–19, 2006.
Australia Physick, Bill
CSIRO Marine and Atmospheric Research 107-121 Station Street; Private Bag 1, Aspendale, 3195 Melbourne
[email protected]
Austria Herman, Friedl
Federal Research and Training Centre for Forests Seckendorf-Gudentweg 8, A-1130 Vienna
[email protected]
Pechinger, Ulrike
Central Institute for Meteorology and Geodynamics, Environmental Meteorology Hohe Warte 38, A-1191 Vienna
[email protected]
Uhrner, Ulrich
Institute for Internal Combustion Engines and Thermodynamics, A-Graz University of Technology Inffeldgasse 21, A-8010 Graz
[email protected]
Belgium Delcloo, Andy
Royal Meteorological Institute of Belgium, Observations Ringlaan 3, 1180 Brussels
[email protected]
xviii
List of Participants
Janssen, Stijn
VITO NV, Integral Environmental Studies Boeretang 200, 2400 Mol
[email protected]
Khaiwal, Ravindra
University of Antwerp, Department of Chemistry Universiteitsplein 1, B-2610 Wilrijk, Antwerp
[email protected]
Mensink, Clemens
VITO NV, Integral Environmental Studies Boeretang 200, 2400 Mol
[email protected]
Schayes, Guy H.
Institute of Astronomy and Geophysics, Universite´ de Louvain Ch. Du Cyclotron 2, B-1348 Louvain-La-Neuve
[email protected]
Brasil Buske, Daniela
UFRGS–Federal University of Rio Grande do Sue, PROMEC–Graduate Program in Mechanical Engineering Av. Dr. Carlos Barbosa, n. 1454 Aptoo 3, 90880-000, Porto Alegra/RS
[email protected]
Bulgaria Batchvarova, Ekaterina
National Institute of Meteorology and Hydrology Blvd. Tzarigradsko Chaussee 66, 1784 Sofia
[email protected]
Ganev, Kostadin
Geophysical Institute, BAS, Physics of the Atmosphere Acad. G. Bonchev, block 3, 1113 Sofia
[email protected]
Canada Hilderman, Trevor
Coanda Research and Development Corp. IIOA-3430 Brighton Ave., V5A 3H4 Burnaby, BC
[email protected]
List of Participants
xix
Kaminski, Jacek
York University, AMDAL/CRESS 4700 Keele St., M3J-1P3, Toronto, Ontario
[email protected]
Norman, Ann-Lise
The University of Calgary, Department of Physics and Astronomy 2500 University Dr., N.W., T2N 1N4 Calgary
[email protected]
Steyn, Douw
University of British Columbia, Department of Earth & Ocean Sciences 6339 Stores Road, V6T 1Z4 Vancouver, B.C.
[email protected]
Czech Republic Brechler, Josef
Charles University, Faculty of Mathematics and Physics, Department of Meteorology & Environmental Protection V Holesˇ ovicˇka´ch 2, 18000 Prague
[email protected]
Halenka, Toma´sˇ
Charles University, Faculty of Mathematics and Physics, Department of Meteorology & Environmental Protection V Holesˇ ovicˇka´ch 2, 18000 Prague
[email protected]
Jicha, Miroslav
Brno University of Technology, Department Mechanical Engineering Technicka 2, 61669 Brno
[email protected]
Pospisil, Jiri
Brno University of Technology, Energy Institute Technicka 2896/2, 61669 Brno
[email protected]
Denmark Gryning, Sven-Erik
Risø National Laboratory, Wind Energy Department, DK-4000 Roskilde
[email protected]
xx
List of Participants
Mahura, Alexander
Danish Meteorological Institute, Department of Research and Development Lyngbyvej 100, DK-2100 Copenhagen
[email protected]
Thykier-Nielsen, Søren
Risø National Laboratory Wind Energy Department, DK-4000 Roskilde
[email protected]
Estonia Kaasik, Marko
Institute of Environmental Physics, University of Tartu U¨likooli 18, 50090 Tartu
[email protected]
Finland Jantunen, Matti
National Public Health Institute (KTL), Department of Environmental Health P.O. Box 95 (Neulaniementie 4), FI 70101 Kuopio matti.jantunen@ktl.fi
Siljamo, Pilvi
Finnish Meteorological Institute, Meteorological Research Erik Palme´nin Aukio 1 (P.O. Box 503), FI 00101 Helsinki pilvi.siljamo@fmi.fi
Sofiev, Mikhail
Finnish Meteorological Institute, Air Quality Erik Palme´nin Aukio 1 (P.O. Box 503), 00561 Helsinki mikhail.sofiev@fmi.fi
France Chaumerliac, Nadine
CNRS—LaMP, Universite´ Blaise Pascal 24 avenue des Landais, 63177 Aubie`re
[email protected]
Deprost, Raphaelle
ASPA—Air Quality Monitoring Network of Alsace, France 5 rue de Madrid, 673000 Schiltigheim
[email protected]
List of Participants
xxi
Leriche, Maud
CNRS—LaMP, Universite´ Blaise Pascal 24 avenue des Landais, 63177 Aubie`re
[email protected]
Menut, Laurent
Laboratoire de Me´te´orologie Dynamique, IPSL/ CNRS E´cole Polytechnique, 91128 Palaiseau
[email protected]
Milliez, Maya
CEREA (ENPC/EDF R&D) 6-8 av. Blaise Pascal, 77455 Champs sur Marne
[email protected]
Vautard, Robert
LSCE/IPSL—Laboratoire CEA/CNRS/UVSQ CEDEX (Bat 701), 91191 Gif sur Yvette
[email protected]
Germany Ebel, Adolf
Rheinish Institute for Environmental Research, University of Cologne Aachener Str. 209, 50931 Ko¨ln
[email protected]
Fay, Barbara
Deutscher Wetterdienst (DWD) (German Weather Service) Kaiserleistr. 42, 63067 Offenbach
[email protected]
Graff, Arno
Umweltbundesamt Wo¨rlitzer Platz 1, 06844 Dessau
[email protected]
Gru¨tzun, Verena
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Heinold, Bernd
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Hellmuth, Olaf
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
xxii
List of Participants
Helmert, Ju¨rgen
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Hugo, Achim
Institut fu¨r Energie-und Umwelttechnik IUTA e. V. Bliersheimer Str. 60, 47229 Duisburg
[email protected]
Kerschbaumer, Andreas
Institut fu¨r Meteorologie, FU Berlin Carl-Heinrich-Becker-Weg 6-10, 12165 Berlin
[email protected]
Klug, Werner
Mittermayerweg 21, 64289 Darmstadt
[email protected]
Knoth, Oswald
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Kotova, Lola
Max-Planck Institute for Meteorology, The Atmoshpere in the Earth System Bundesstr. 53, 20146 Hamburg
[email protected]
Martens, Reinhard
Gesellschaft fu¨r Anlagen- und Reaktorsicherheit Schwertnergasse 1, 50667 Ko¨ln
[email protected]
Memmesheimer, Michael
Rheinish Institute for Environmental Research, University of Cologne Aachener Str. 201, 50931 Cologne
[email protected]
Reimer, Eberhard
Freie Universita¨t Berlin, Institut fu¨r Meteorologie Carl-Heinrich-Becker-Weg 6-10, 12165 Berlin
[email protected]
Renner, Eberhard
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Rinke, Rayk
Institut fu¨r Meteorologie und Klimaforschung, Forschungszentrum Karlsruhe/Universtita¨t Karlsruhe Postfach 3640, 76021 Karlsruhe
[email protected]
List of Participants
xxiii
Schlink, Uwe
Umweltforschungszentrum Leipzig-Halle GmbH (UFZ), Department Expositionsforschung und Epidemiologie Permoserstr. 15, 04318 Leipzig
[email protected]
Stern, Rainer
Freie Universita¨t Berlin, Institut fu¨r Meteorologie Carl-Heinrich-Becker-Weg 6-10, 12165 Berlin
[email protected]
Streuber, Oliver
Peutz Consult GmbH Kolberger Str. 19, 40599 Du¨sseldorf
[email protected]
Tegen, Ina
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Torras Ortiz, Sandra
IER, Universita¨t Stuttgart, TFU Heßbru¨hlstr. 49-A, 70565 Stuttgart
[email protected]
Trukenmu¨ller, Alfred
Federal Environment Agency (UBA) of Germany Wo¨rlitzer Platz 1, 06844 Dessau
[email protected]
Vogel, Heike
Leibniz Institut fu¨r Meteorologie und Klimaforschung, Forschungszentrum Karlsruhe/ Universtita¨t Karlsruhe Postfach 3640, 76021 Karlsruhe
[email protected]
Wolke, Ralf
Leibniz Institute for Tropospheric Research Permoserstr. 15, 04318 Leipzig
[email protected]
Greece Astitha, Marina
University of Athens, Department of Applied Physics University Campus, Bldg. PHYS-V, 15784 Zografou, Athens
[email protected]
List of Participants
xxiv
Douros, John
Aristotle University of Thessaloniki, Mechanical Engineering University Campus, BOX 483, 54124 Thessaloniki
[email protected]
Kallos, George
University of Athens, School of Physics University Campus, Bldg. PHYS-5, 15784 Athens
[email protected]
Israel Haikin, Nitsa
NRCN P.O.B. 9001, 84190 Beer-Sheva
[email protected]
Kishcha, Pavel
Tel-Aviv University, Department of Geophysics and Planetary Sciences Ramat Aviv, 69978 Tel-Aviv
[email protected]
Reisin, Tamir
Soreq Nuclear Research Center, Applied Physics 81800 Yavne
[email protected]
Italy Anfossi, Domenico
CNR—ISAC Corso Fiume 4, 10133 Torino
[email protected]
Bedogni, Marco
Agenzia Mobilita` E Ambiente, Ambiente E Energia Via Beccaria 19, 20122 Milano
[email protected]
Borghi, Sergio
Osservatorio Meteorologico di Milano-Duomo Piazza Duomo 21, 20121 Milano
[email protected]
Carnevale, Claudio
University of Brescia, DEA Via Branze 38, 25123 Brescia
[email protected]
List of Participants
xxv
Carpentieri, Matteo
University of Florence, Dipartimento di Energetica Via S. Marta 3, 50139 Firenze
[email protected]fi.it
Di Sabatino, Silvana
University of Lecce, Dipartimento di Scienza dei Materiali SP Lecce—Monteroni, 73100 Lecce
[email protected]
Favale, Giuseppe
University of Naples ‘‘Federico II’’, Chemical Engineering Department P. le Tecchio 80, 80100 Napoli
[email protected]
Favaron, Maurizio
Servizi Territorio Via Garibaldi 21, 20092 Cinisello Balsamo
[email protected]
Minguzzi, Enrico
Regional Meteorological Service of Emilia Romagna—Italy (ARPA—SIM) Viale Silvani 6, 40726 Bologna
[email protected]
Murena, Fabio
University of Naples, Chemical Engineering Department P. le Tecchio 80, 80125 Napoli
[email protected]
Santese, Federica
University of Lecce, Material Science Department Prov. Lecce—Monteroni—Polo Scientifico, 73100 Lecce
[email protected]
Trini Castelli, Silvia
Institute of Atmospheric Sciences and Climate— C.N.R. Corso Fiume 4, 10133 Torino
[email protected]
Zappala`, Daniele
Osservatorio Meteorologico di Milano-Duomo Piazza Duomo 21, 20121 Milano
[email protected]
xxvi
List of Participants
Japan Kajino, Mizuo
Division of Global Atmospheric Environment Research Center for Advanced Science and Technology, The University of Tokyo, 4-6-1 Komaba, Meguro, Tokyo, Japan
[email protected]
Kitada, Toshihiro
Toyohashi University of Technology, Department of Ecological Engineering Tempaku-cho, 441-8580 Toyohashi
[email protected]
Yumimoto, Keiya
Kyushu University, Department of Earth System Science Kasuga Park 6—1, 816-8580 Kasuga, Fukuoka
[email protected]
Lithuania Ulevicius, Vidmantas
Institute of Physics, Environmental Physics and Chemistry Savanoriu 231, LT-02300 Vilnius
[email protected]
Norway Fløisand, Inga
Norwegian Institute for Air Research (NILU) P.O. Box 100, 2027 Kjeller
[email protected]
Seland, Øyvind
University of Oslo, Department of Geosciences P.O. Box 1022 Blindern, 0315 Oslo
[email protected]
Portugal Alvim-Ferraz, Maria C.
LEPAE, Departamento de Engenharia Guinia, Fauldade de Engenharia, Universidade do Porto Dr. Roberto Frias, 4200-461 Porto
[email protected]
Borrego, Carlos
Universidade de Aveiro, Departamento Ambiente e Ordenanento Campus Universita´rio de Santiago, 3810 193 Aveiro
[email protected]
List of Participants
xxvii
Grosso, Nuno
New University of Lisbon, Department of Science and Environmental Engineering Campus da Caparica, Quinta da Torre, 2829-516 Caparica
[email protected]
Mesquita, Sandra
New University of Lisbon, Department of Science and Environmental Engineering Campus da Caparica, Quinta da Torre, 2829-516 Caparica
[email protected]
Miranda, Ana Isabel
Universidade de Aveiro, Departamento Ambiente e Ordenanento Campus Universita´rio de Santiago, 3810-193 Aveiro
[email protected]
Monteiro, Maria Alexandra
Universidade de Aveiro, Departamento Ambiente e Ordenanento Campus Universita´rio de Santiago, 3810-193 Aveiro
[email protected]
Tente, Hugo
New University of Lisbon, Department of Science and Environmental Engineering Campus da Caparica, Quinta da Torre, 2829-516 Caparica
[email protected]
Valente, Joana
Universidade de Aveiro, Departamento Ambiente e Ordenanento Campus Universita´rio de Santiago, 3810-193 Aveiro
[email protected]
Russia Genikhovich, Eugene
Main Geophysical Observatory, Department of Monitoring of Air Pollution 7 Karbyshev St., 194021 St. Petersburg
[email protected]
xxviii
Kuchmenko, Ekaterina
List of Participants
Melentiev Energy Systems Institute, Siberian branch RAS Lermontova 130, 664033 Irkutsk
[email protected]
Spain Baldasano, Jose M.
Barcelona Supercomputing Center (BSC), Earth Sciences Jordi Girona 29 (Edificeo Nexus II), 08034 Barcelona
[email protected]
San Jose, Roberto
Technical University of Madrid (UPM), Environmental Software and Modelling Group Campus de Montegancedo, ES 28660 Boadilla del Monte (Madrid) roberto@fi.upm.es
Soler, Maria Rosa
University of Barcelona, Astronomy and Meteorology Avinguda Diagonal 647, 08028 Barcelona
[email protected]
Souto, Jose A.
University of Santiago de Compostela, Chemical Engineering Campus sur School of Engineering, 15782 Santiago de Compostela
[email protected]
Sweden Kahnert, Michael
Swedish Meteorological and Hydrological Institute (SMHI) Folkborgsva¨gen 1, 60176 Norrko¨ping
[email protected]
Robertson, Lennart
Swedish Meteorological and Hydrological Institute (SMHI) Folkborgsva¨gen 1, 60176 Norrko¨ping
[email protected]
List of Participants
xxix
Switzerland Andreani-Aksoyoglu, Sebnem
Paul Scherrer Institute (PSI), Laboratory of Atmospheric Chemistry 5232 Villigen PSI
[email protected]
The Netherlands Barbu, Alina Lavinia
Delft University of Technology, Delft Institute of Applied Mathematics Mekelweg 4, 2628 CD Delft
[email protected]
Builtjes, Peter
TNO, Environmental Quality P.O. Box 342, 7300 AH (7204 AT) Apeldoorn
[email protected]
Koopmans, Ferry
Peutz bv, Industrial Department Lindenlaan 41, 6584 AC Molenhoek
[email protected]
Sauter, Ferd
RIVM (Nat. Inst. of Public Health and the Environment) P.O. Box 1, 3720 BA Bilthoven
[email protected]
Schaap, Martijn
TNO, Environment, Health and Safety Laan van Westenenk 501, 7300 AH Apeldoorn
[email protected]
van den Akker, Stephan
Peutz bv, Industrial Department Lindenlaan 41, 6584 AC Molenhoek
[email protected]
van Dop, Han
Institute for Marine and Atmospheric Research (IMAK), Utrecht University P.O. Box 80.005, 3508 TA Utrecht
[email protected]
xxx
List of Participants
Turkey Incecik, Selahattin
Istanbul Technical University, Faculty of Aeronautics and Astronautics, Department of Meteorological Engineering Campus Maslak, 34469 Maslak
[email protected]
United Kingdom Baldi, Sandro
University of Surrey, Fluids & Systems/School of Engineering University Campus, G02 7XH Guildford
[email protected]
Dore, Anthony
Centre for Ecology & Hydrology, Atmospheric Sciences Bush Estate, EH26 9HF Penicuik, Midlothian
[email protected]
Fisher, Bernard
Environment Agency, Risk and Forecasting Kings Meadow Road, RG1 8DQ Reading bernard.fi
[email protected]
Jenkinson, Pete
Westlakes Scientific Consulting Ltd., Air Pollution Group Westlakes Science & Technology Park, CA24 3LN Moor Row
[email protected]
Shi, Ji Ping
The Environment Agency, Air Quality Modelling and Assessment Unit 29 Newport Road, CF24 0TP Cardiff
[email protected]
Smith, Justin Gillett
Health Protection Agency HPA-RPD Chilton, OX11 ORQ Didcot
[email protected]
Walker, Helen L.
University of Birmingham, Geography Edgbaston, B15 2TT Birmingham
[email protected]
List of Participants
xxxi
USA Bullock, Russell
NOAA Air Resources Laboratory/U.S. EPA U.S. EPA, Mail Drop E243-03, 27711 Research Triangle Park, NC
[email protected]
Byun, Daewon
University of Houston, Department of Geosciences 312 Science & Research Building. 1, TX 77204 Houston, Texas
[email protected]
Cooter, Ellen
NOAA/Atmospheric Sciences Modeling Division (In Partnership with the U.S. Environmental Protection Agency) 109 TW Alexander Drive U.S. Environmental Protection Agency (MD- E243-4) Research Triangle Park, NC 27711
[email protected]
Hanna, Steven
Harvard University 7 Crescent Ave., 04046 Kennebunkport, Maine
[email protected]
Hodzic, Alma
National Center for Atmospheric Research (NCAR) Atmospheric Chemistry Division 3450 Mitchell Lane Boulder, CO 80301
[email protected]
Hogrefe, Christian
University of Albany, Atmospheric Sciences Research Center 251 Fuller Road, 12203 Albany
[email protected]
Kang, Daiwen
U.S. EPA 27711 Research Triangle Park, NC
[email protected]
Lee, Pius
National Centers for Environmental Prediction USA (NOAA), DOC 5200 Auth Rd., MD 20746 Camp Springs
[email protected]
xxxii
List of Participants
Odman, Mehmet Talat
Georgia Institute of Technology, Civil & Environmental Engineering 311 Ferst Drive, 30322-0512 Atlanta, GA
[email protected]
Porter, P. Steven
University of Idaho, Civil Engineering 1776 Science Center, Suite 306, 83402 Idaho Falls
[email protected]
Rao, S. Trivikrama
NOAA/EPA Atmospheric Sciences Modeling Division 106 TW Alexander Drive, Room E 242, 27711 Research Triangle Park, NC
[email protected]
Sarwar, Golam
U.S. EPA/Atmospheric Modeling Division 106 TW Alexander Drive, Mail Drop E 243-3, 27711 Research Triangle Park, NC
[email protected]
Schiermeier, Frank
U.S. NOAA (Retired) 303 Glasgow Road, 27511 Cary, NC
[email protected]
Watkins, Timothy
United States Environmental Protection Agency (U.S. EPA), Office of Research and Development MD E205-01, 27711 Research Triangle Park, NC
[email protected]
Yu, Shaocai
U.S. EPA, Department AMD (E243-01) NERL, 27711 Research Triangle Park, NC
[email protected]
xxxiii
The members of the scientific committee for the 28th NATO/ CCMS international technical meeting on air pollution modeling and its application
G. Schayes, Belgium D. Syrakov, Bulgaria D. Steyn, Canada S.-E. Gryning, Denmark N. Chaumerliac, France E. Renner, Germany G. Kallos, Greece D. Anfossi, Italy
P. Builtjes, The Netherlands T. Iversen, Norway C. Borrego, Portugal (Chairman) J. M. Baldasano, Spain S. Incecik, Turkey B. Fisher, United Kingdom F. Schiermeier, United States S. Trivikrama Rao, United States
This page intentionally left blank
xxxv
History of NATO/CCMS air pollution pilot studies
Pilot Study on Air Pollution: International Technical Meetings (ITM) on Air Pollution Modeling and Its Application Dates of Completed Pilot Studies: 1969
–
1975
–
1980
–
1974 Air Pollution Pilot Study (Pilot Country– United States) 1979 Air Pollution Assessment Methodology and Modelling (Pilot Country–Germany) 1984 Air Pollution Control Strategies and Impact Modeling (Pilot Country–Germany)
Dates and Locations of Pilot Study Follow-Up Meetings: Pilot Country
–
February 1971
–
July 1971
–
United States (R. A. McCormick, L. E. Niemeyer) Eindhoven, The Netherlands First Conference on Low Pollution Power Systems Development Paris, France Second Meeting of the Expert Panel on Air Pollution Modelling
All of the following meetings were entitled–NATO/CCMS International Technical Meetings (ITM) on Air Pollution Modeling and Its Application. October 1972 May 1973
– –
June 1974 Pilot Country September 1975
– – –
Paris, France Third ITM Oberursel, Federal Republic of Germany Fourth ITM Roskilde, Denmark Fifth ITM Germany (Erich Weber) Frankfurt, Federal Republic of Germany, Sixth ITM
History of NATO/CCMS Air Pollution Pilot Studies
xxxvi
September 1976 September 1977 August 1978 October 1979 Pilot Country November 1980 August 1981 September 1982 September 1983 April 1985 Pilot Country April 1987
– – – – – – – – – – – –
September 1988
–
May 1990
–
September 1991 Pilot Country November 1993 November 1995
– – – –
June 1997
–
September 1998 May 2000
– –
Pilot Country October 2001
– –
May 2003 October 2004 May 2006
– – –
Airlie House, Virginia, USA, Seventh ITM Louvain-la-Neuve, Belgium, Eighth ITM Toronto, Ontario, Canada, Ninth ITM Rome, Italy, Tenth ITM Belgium (C. De Wispelaere) Amsterdam, The Netherlands, Eleventh ITM Menlo Park, California, USA, Twelfth ITM Ile des Embiez, France, Thirteenth ITM Copenhagen, Denmark, Fourteenth ITM St. Louis, Missouri, USA, Fifteenth ITM The Netherlands (Han van Dop) Lindau, Federal Republic of Germany, Sixteenth ITM Cambridge, United Kingdom, Seventeenth ITM Vancouver, British Columbia, Canada, Eighteenth ITM Ierapetra, Crete, Greece, Nineteenth ITM Denmark (Sven-Erik Gryning) Valencia, Spain, Twentieth ITM Baltimore, Maryland, USA, Twenty-First ITM Clermont-Ferrand, France, Twenty-Second ITM Varna, Bulgaria, Twenty-Third ITM Boulder, Colorado, USA (Millennium), Twenty-Fourth ITM Portugal (Carlos Borrego) Louvain-la-Neuve, Belgium, Twenty-Fifth ITM Istanbul, Turkey, Twenty-Sixth ITM Banff, Canada, Twenty-Seventh ITM Leipzig, Federal Republic of Germany, Twenty-Eighth ITM
xxxvii
Preface
In 1969, the North Atlantic Treaty Organization (NATO) established the Committee on Challenges of Modern Society (CCMS). The subject of air pollution was from the start one of the priority problems under study within the framework of various pilot studies undertaken by this committee. The organization of a periodic conference dealing with air pollution modelling and its application has become one of the main activities within the pilot study relating to air pollution. The first five international conferences were organized by the United States as the pilot country, the second five by the Federal Republic of Germany, the third five by Belgium, the fourth four by The Netherlands, the next five by Denmark and the last four by Portugal. This volume contains the abstracts of papers and posters presented at the 28th NATO/CCMS International Technical Meeting on Air Pollution Modeling and Its Application, held in Leipzig, Germany, during May 15–19, 2006. This ITM was jointly organized by the University of Aveiro, Portugal (pilot country), and by the Leibniz-Institute for Tropospheric Research, Germany (host organization). The key topics distinguished at this ITM included: Local and urban scale modeling; Regional and intercontinental modelling; Data assimilation and air quality forecasting; Model assessment and verification; Aerosols in the atmosphere; Interactions between climate change and air quality; Air quality and human health. The ITM was attended by 129 participants representing 27 countries from Asia, Australia, Europe as well as North and South America. Invited papers were presented by J. W Kaminski, Canada (Multiscale air quality modelling: Progress and challenges), M. Jantunen, Finland (Air pollution exposure modelling for risk assessment and for risk management) and S. R. Hanna (A review of uncertainty and sensitivity analyses of atmospheric transport and dispersion models). On behalf of the ITM Scientific Committee and as organizers and editors, we would like to thank all the participants who made the meeting so successful. Among the participants, we especially recognize the efforts of the chairpersons and rapporteurs. Finally, special thanks to the
xxxviii
Preface
sponsoring institutions University of Aveiro, Portugal, Leibniz-Institute for Tropospheric Research, Germany and the sponsoring organizations NATO Committee on the Challenges of Modern Society and GRICES (Office for International Relations in Science and Higher Education, Portugal). A special grant was given by EURASAP (European Association for the Sciences of Air Pollution) to award a prize to young researchers for the best paper or poster. The next conference will be held in 2007 in Portugal. Eberhard Renner (Local Conference Organizer) Germany Carlos Borrego (Scientific Committee Chairperson) Portugal
Local and urban scale modelling Chairpersons: Domenico Anfossi Guy Schayes Rapporteurs: Matteo Carpentieri Ana Margarida Costa
This page intentionally left blank
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06011-1
3
Chapter 1.1 Application and validation of FLUENT flow and dispersion modelling within complex geometries Silvana Di Sabatino, Riccardo Buccolieri, Beatrice Pulvirenti and Rex Britter Abstract Flow patterns around buildings have a strong influence on pollutant dispersion derived from sources placed within the urban area. Computational fluid dynamics (CFD) codes are used to provide solutions to the fundamental fluid dynamics equations at spatial scales smaller than the typical urban ones. In this work, dispersion of pollutant from sources near buildings forming various street canyons is studied by means of the general purpose CFD code FLUENT to investigate the influence of small geometric features on pollutant concentration distributions. Firstly, we study the effects of a complex geometry on the flow near the ground by considering a finite array of rectangular and square-shaped rings of buildings with different aspect ratios. Secondly, we study transport and diffusion of pollutant within a finite array of rectangular buildings. FLUENT concentration results are validated against wind tunnel data (CEDVAL, 2002). Numerical simulations are performed using the Reynolds Averaged Nervier– Stokes (RANS) k–e turbulence model and the advection–diffusion model. The paper documents the potential of a general purpose CFD model for the simulation of pollutant dispersion close to emission sources and within complex building arrangements in an operational context. 1. Introduction
Predicting pollutant dispersion in urban areas is currently one of the most important environmental problems, especially because of the risks associated with the exposition of a large part of the population to high pollutant concentrations.
4
Silvana Di Sabatino et al.
Studies in complex building configurations have shown that a variation of small-scale features of the building geometry has a strong influence on the flow and pollutant concentration distribution in street canyons. Dispersion is affected by a number of different factors: emission source characteristics, meteorological conditions, complex geometries and building arrangements within the urban area. Among all methods to study flow and dispersion in urban areas, computational fluid dynamics (CFD) modelling plays an important role. CFD models are useful tools for predicting air quality (Craig et al., 2001). In particular, they allow the study of flow characteristics and concentration patterns in street canyons and within urban areas, interpret wind tunnel and field data and therefore improve operational models. However, up to now most available general purpose models still need to be validated against wind tunnel or field data to obtain confidence before applying them to a particular case study. Pollutant concentration distribution at a given location is very sensitive to geometry simplifications which, however, are often applied in typical numerical dispersion modelling. The great advantage of numerical models seems to be reduced if many simplifications of the urban morphometry are made (Chauvet et al., 2001). Wind tunnel experiments have demonstrated that the street ventilation is reduced in the presence of upstream buildings. This seems to be because of the upward displacement of the flow and the consequent perturbed momentum exchange between the street canyon and the outer region of the flow (Kastner-Klein and Plate, 1999). Also, numerical results have indicated that surrounding building configuration affects pollutant dispersion in a street canyon, therefore it should be taken into account in numerical dispersion modelling (Xie et al., 2005). This paper is an attempt to investigate if a general purpose CFD model such as FLUENT (Fluent, Inc., 2005) can be used as a practical tool for the study of pollutant dispersion distributions in complex geometry such as an urban area. The modelling of flow and dispersion is based on the Reynolds Averaged Navier–Stokes (RANS) flow equations. RANS has been widely used for flow and pollutant dispersion modelling in street canyons, showing to perform well when compared with wind tunnel and field data (see for example Xie et al. (2005) and Santiago et al. (2006)).
2. Description of CEDVAL experiments
In this paper, we validate FLUENT simulations with wind tunnel experiments CEDVAL (2002). We consider the following three cases.
Application and Validation of FLUENT Flow and Dispersion Modelling
5
Configuration B1-1. This experiment was made in a boundary layer wind tunnel to simulate the case of dispersion of pollutants from naturally ventilated underground parking garages (Leitl and Schatzmann, 2000). A finite array of idealized building blocks with 0.1 m by 0.15 m base dimensions and 0.125 m height (three buildings crosswind and seven buildings along wind direction) are considered as shown in Fig. 1 (top, left). The aspect ratio of the street canyons resulting from the building arrangement is W ¼ H ¼ 0.8. Four ground level CO emission sources were mounted close to the building as shown in Fig. 1 (top, right). Flow and CO dispersion were measured within the street canyon, downwind the building equipped with the sources. Concentrations are shown in a dimensionless form using the following expression: K¼
C means U ref H 2 C source Q
(1)
where Cmeans is the measured tracer concentration, Csource is the tracer concentration at the source (1 in this case), Uref is the reference wind speed (undisturbed flow) at 3H, H is the building height and Q the emission source strength (m3s1). Configuration B1-2. In this case, a regular array of street canyons with 56 square-shaped building rings was considered. These buildings, having dimensions of 0.25 m by 0.25 m by 0.06 m, were mounted in rows of four rings across the wind tunnel. The configuration is shown in Fig. 1
Figure 1. Geometry of CEDVAL experiments: B1-1 (top) and B1-2 (bottom).
Silvana Di Sabatino et al.
6
(bottom). The aspect ratio of the street canyons resulting from the building arrangements is W ¼ H ¼ 1. Flow within the street canyons was measured. Configuration B1-3. This case is the same as B1-2 with a different aspect ratio of W ¼ H ¼ 3. 3. FLUENT flow and dispersion modelling 3.1. Flow setup
All FLUENT simulations were carried out by considering a neutral boundary layer. The size of the computational domain used to simulate the boundary layer is 7 m by 2 m in the horizontal plane and 0.5 m in the vertical direction. The computational domain was built using hexahedral elements with finer resolution close to the ground and in those regions where the plume is evolving. The overall number of computational cells used is about half million for case B1-1 and about one million for cases B1-2 and B1-3. The smallest dimensions of the elements are equal to 0.005 m while they are about 0.025 m outside the intersection. Several tests to verify grid size independence were made with increasing mesh numbers until further refinements give no significant improvements. The k–e model (Launder and Spalding, 1974) was used. Recently, Xie et al. (2005) found a good performance of the k–e model in simulating emissions from vehicle exhausts in a street canyon within an urban environment. We used the same boundary conditions as in Di Sabatino et al. (2005). Based on CEDVAL experiments, the inlet wind speed was assumed to be described by a power law profile with height z: p uðzÞ z ¼ (2) uref zref where u(z) is the average wind speed at the height z above the ground, uref the reference wind speed at the reference height zref and p is the vertical wind profile exponent. Turbulent kinetic energy and dissipation rate profiles are specified as follows: ! 2 u z k ¼ pffiffiffiffiffiffi 1 (3) d Cm
¼
! 3 u z 1 d kz
(4)
Application and Validation of FLUENT Flow and Dispersion Modelling
7
where d is the boundary layer height, Cm ¼ 0.09 a coefficient used to define the eddy viscosity in k–e models, u the friction velocity and k the von Karman’s constant. 3.2. Dispersion setup
CO was considered as the pollutant emitted from the sources. The advection diffusion (AD) module was used. In turbulent flows, FLUENT computes the mass diffusion that satisfies the conservation of mass as follows: m J CO ¼ rDCO þ t rY CO (5) Sct where DCO is the diffusion coefficient for CO in the mixture, mt ¼ ð1=2ÞC m k2 = is the turbulent viscosity, YCO is the mass fraction of CO, r is the mixture density. Sct ¼ mt =ð1=2Dt Þ is the turbulent Schmidt number, where Dt is the turbulent diffusivity. Sources were simulated by separating four volumes in the geometry at the required discharge position and by setting CO source terms (3 103 g s1) for these volumes. These volumes have the same dimensions of the sources used in wind tunnel experiments (CEDVAL, 2002). 4. Results 4.1. Flow field in a finite array of rectangular buildings and square-shaped rings of buildings
FLUENT flow results are compared with CEDVAL data obtained from configurations B1-1, B1-2 and B1-3. Wind tunnel experiments and numerical simulations show that a recirculation flow region forms within a street canyon exposed to a perpendicular flow. The ability of capturing the right dimension of the vortex is very important as the vortex drives the distribution of pollutants within the street canyon. Figure 2 shows velocity vectors on the vertical plane in the middle of the street canyon for configuration B1-1. The figure shows that the shape and the dimension of the vortex predicted by FLUENT is very similar to that observed by CEDVAL experiments. Both wind tunnel measurements and FLUENT predictions show that for aspect ratio W ¼ H ¼ 0.8 a single vortex forms inside the canyon. For aspect ratio equal to 1 (case B1-2), we observe a single vortex inside the street canyon, while for aspect ratio equal to 3 (case B1-3), a wake
8
Silvana Di Sabatino et al.
Figure 2. Velocity vectors from CEDVAL experiment: B1-1 (left) and FLUENT results (right).
Figure 3. Velocity vectors from FLUENT for configurations B1-2 (left) and B1-3 (right).
interference flow regime is observed, as shown by Fig. 3 and as already pointed out by Johnson and Hunter (1999). Also, velocity profiles show a very good agreement between FLUENT and CEDVAL data as shown in Fig. 4, where dimensionless velocity profiles u/Uref are plotted versus dimensionless height z/H, for configurations B1-1, B1-2 and B1-3 (top, middle and bottom, respectively).
4.2. Dispersion in a finite array of rectangular buildings
Riddle et al. (2004) showed that FLUENT dispersion spread from high level point source, calculated by using algebraic Reynolds stress models (RSM) is smaller than that predicted by the well-validated integral model ADMS-Urban. We found the same results for both the point source and the line source using the standard k–e model (Di Sabatino et al., 2005).
Application and Validation of FLUENT Flow and Dispersion Modelling
9
Figure 4. Comparisons between velocity profiles from FLUENT and from CEDVAL experiments: B1-1 (top), B1-2 (middle) and B1-3 (bottom); on three different planes: leeward (left), in the middle of the canyon (middle) and windward (right).
Therefore, we performed some sensitivity tests for the choice of the most suitable Sct in order to artificially increase plume dispersion. From the sensitivity test, the value of 0.4 resulted to be the most appropriate one. So in this paper, both the calculated results with Sct ¼ 0.4 and Sct ¼ 0.7 (the standard value) are compared with wind tunnel data (CEDVAL). Figure 5 (top) shows the dimensionless coordinate y ¼ H versus the dimensionless concentration K near the floor (z ¼ H ¼ 0.06) within the street canyon. Figure 5 (bottom) shows dimensionless concentration K versus dimensionless coordinate x ¼ H on the same vertical plane. The horizontal velocity near the floor is negative because the vortex in the canyon is clockwise. So pollutants are carried towards the leeward side and mixed in the street canyon. FLUENT results agree well with wind tunnel measurements.
10
Silvana Di Sabatino et al.
Figure 5. Dimensionless CO concentration profiles along y for x ¼ H ¼ 1 (top) and along x for y ¼ H ¼ 1 (bottom), for configuration B1-1.
5. Conclusions
In this paper, the k–e turbulence model of the CFD code FLUENT was used to simulate flow and pollutant dispersion within street canyons resulting from complex building configurations. The validation of numerical results is done using a compilation of wind tunnel data available on the web (CEDVAL). The validation showed that there is a good agreement between the model and wind tunnel measurements from which we can conclude that a general purpose CFD model can be used to simulate pollutant dispersion in the atmosphere. However, the analysis has shown that a number of considerations are required before achieving the final results, i.e., about the grid resolution, inlet conditions, discretization methods and the selection of the appropriate turbulence and dispersion models. To make our conclusions more general, we suggest that the accuracy of FLUENT results in complex building configurations should be further assessed by considering other turbulence models and by improving the modelling of pollutant emissions.
REFERENCES CEDVAL, 2002. http://www.mi.uni-hamburg.de/cedval-validation-data.427.0.html Tech. rep categories B1-1, B1-2 and B1-3.
Application and Validation of FLUENT Flow and Dispersion Modelling
11
Chauvet, C., Kastner-Klein, P., Kovar-Panskus, A., Savory, E., Schatzmann, M., 2001. The use of wind tunnels in modelling air quality street canyons. Final Report of the TMR Research Network TRAPOS: Optimization of Modelling Methods for Traffic Pollution Streets. European Commission. Craig, K.J., De Kock, D.J., Snyman, J.A., 2001. Minimizing the effect of automotive pollution in urban geometry using mathematical optimization. Atmos. Environ. 35, 579–587. Di Sabatino, S., Buccolieri, R., Pulvirenti, B., Britter, R., 2005. Flow and pollutant dispersion modelling in street canyons using Fluent and ADMS-Urban. 5th International Conference on Urban Air Quality. Valencia. Fluent, Inc., 2005. 6.2 User Manual. http://www.fluent.com Johnson, G., Hunter, L., 1999. Some insights into typical urban canyon airflows. Atmos. Environ. 33, 3991–3999. Kastner-Klein, P., Plate, E., 1999. Wind tunnel study of concentration fields in street canyons. Atmos. Environ. 33, 3973–3979. Launder, B., Spalding, D., 1974. The numerical computation of turbulent flows. Comput. Methods Appl. Mech. Eng. 3, 269–289. Leitl, B., Schatzmann, M., 2000. Physical modelling of emissions from naturally ventilated underground parking garages. Environ. Monit. Assess. 65, 221–229. Riddle, A., Carruthers, D., Sharpe, A., McHugh, C., Stocker, J., 2004. Comparisons between FLUENT and ADMS for atmospheric dispersion modelling. Atmos. Environ. 38, 1029–1038. Santiago, J., Martilli, A., Martin, F., 2006. Validation of CFD simulation of turbulent air 1ow over a regular array of cubes against wind tunnel data and 3D analysis of the 1ow. Proc. 14th Joint Conference on the Applications of Air Pollution Metereology with the Air and Waste Management Assoc., Atlanta. Xie, X., Huang, Z., Wang, J., 2005. Impact of building configuration on air quality in street canyon. Atmos. Enviro. 39, 4519–4530.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06012-3
12
Chapter 1.2 Turbulence, atmospheric dispersion and mixing height in the urban area, recent experimental findings Sven-Erik Gryning and Ekaterina Batchvarova Abstract The parameterisation of the complex structure of the atmosphere over urban areas has large implication in running and testing mesoscale meteorological and air pollution models. The typical size for the urban area is of the order of 20–50 km. It is subdivided into a large number of areas (neighbourhoods) reflecting the development of the town, such as the central inner, residential, recreation and industrial parts. The description of the ceaseless adjustments of the flow in the urban area is simplified by introducing neighbourhoods that are complexly interacting with the flow and forming internal boundary layers. On the level of street canyons, the roughness sublayer, the flow varies in space and time. At a level of 3–5 times, the average building height the flow is in equilibrium with the underlying surface, known as inertial sub-layer. Higher up, the differences in meteorological fields introduced by surface characteristics of different neighbourhoods are blended and the boundary layer is forced by area-aggregated features. Within this framework, the parameterisation of some meteorological quantities is reviewed. Based on tracer experiments, it is found that the ability to predict the crosswind spread of the plume as well as maximum concentrations in the urban environment is within a factor of 2. 1. Introduction
The dynamical effects of urban and areas with high surface roughness are traditionally modelled by only one parameter, the roughness length. This is a highly simplified approach because the roughness is not a physical length scale. It is defined by extrapolation of the logarithmic wind profile down to the level where the wind disappears. Therefore the surface roughness can only be defined when a logarithmic wind profile exists. In
Turbulence, Atmospheric Dispersion and Mixing Height
13
an urban area, the character of the surface changes between the different areas. Hence it is not obvious that a logarithmic wind profile even exists and the roughness length becomes an artefact. In the real atmosphere, the surface roughness and thermal effects are combined, which adds time dependence on the various scales to the flow. Figure 1 shows a sketch of an urban area with an indication of the scales and their regimes. It looks complicated but constitutes a considerable idealization. At the abrupt change between rural and urban surface, an internal boundary layer starts to form, as shown in the left panel of Fig. 1. Mixing above the city is in this case confined within the internal boundary layer. The situation is also found in coastal areas. In simplified form, the growth of the neutral internal boundary layer is given in the following equation: dh u dt
(1)
A fully developed mixed layer is illustrated in the right panel of Fig. 1. In the case of neutral conditions the mixing reaches: h
0:1u f
(2)
where h is the height of the (internal) boundary layer, u* is the friction velocity, f is the Coriolis parameter and t is time. Integrating Eq. (1),
Figure 1. Schematic picture of the boundary layer structure over an urban area. The different hatchings represent the underlying surface of the various neighbourhoods. Broad spaced patterns represent the urban internal boundary layers where advection processes are important. Fine spaced patterns show the inertial sub-layers that are in equilibrium with the underlying surface and where Monin–Obukhov scaling applies. The forward slash pattern is the roughness sub-layer that is highly inhomogeneous in its vertical and horizontal structure. Between the buildings, the momentum is transformed into heat by pressure and viscous forces. Dotted pattern represents adjustment between neighbourhoods with large accelerations and shear in the flow near the top of the canopy. At the height where the internal boundary layers are intermixed, the effects of the individual neighbourhoods cannot be distinguished any more—the so-called blended layer.
14
Sven-Erik Gryning and Ekaterina Batchvarova
setting t ¼ x/u and comparing with Eq. (2), we obtain a rough estimate of the distance x where the internal boundary layer reaches its equilibrium height: x
0:1u f
(3)
Beyond this distance, the boundary layer is forced by the urban surface conditions only. It can be noted that the distance does not depend on surface roughness but only on wind speed and f. At a wind speed of 5 m s1 and the Coriolis parameter 104 s1, the equilibrium distance is about 5 km. The atmospheric dispersion parameters in each of the layers are vastly different, and as a consequence, the models to simulate the dispersion process are also of different nature. The complex structure of the urban atmosphere makes the simulation of the dispersion process a real challenge. Some success has been achieved for the canopy layer (forward slash pattern in the sketch) and at larger scales (blended layer). The challenge in the transition layers (broad and fine space horizontal patterns) is still considerable. 2. Tracer experiments
Measurements from the Copenhagen and BUBBLE full-scale tracer experiments are used to investigate the ability to model the dispersion process in an urban area. 2.1. Copenhagen experiment
Atmospheric dispersion experiments were carried out in the Copenhagen area with tracer released from an elevated source in the urban/residential area (Gryning and Lyck, 1984). The tracer sulphur hexafluoride, an inert gas tracer, was released from a tower at a height of 115 m and collected near ground level in crosswind arcs 2–6 km from the source (see Fig. 2). Data from the experiment are available in Gryning and Lyck (2002). The tracer sampling time was 1 h. The site in both the upwind and the downwind directions was mainly residential. The meteorological measurements included turbulence at the height of the tracer release, profiles of temperature and wind along the mast and the standard routine radiosoundings launched 4 km northeast of the tracer release point. All tracer experiments were performed during daytime in neutral to slightly convective atmospheric conditions.
Turbulence, Atmospheric Dispersion and Mixing Height
15
Figure 2. Copenhagen experiment. Left: Tracer sampling set up for the experiments in Copenhagen. Typically 20 locations in each arc situated in the actual plume direction for the individual experiments were used. Right: View from the tracer release point.
Figure 3. BUBBLE tracer experiment. Left: Tracer sampling set up for the experiments in Basel (Switzerland). Typical 12 locations in the actual plume direction for the individual experiments were used. Right: Tracer unit at roof sampling position.
2.2. BUBBLE tracer experiment
The BUBBLE tracer experiment represents the dispersion characteristics over a typical European city (Rotach et al., 2004, Batchvarova and Gryning, 2006). It was designed as an urban roof-level tracer experiment (Fig. 3). Four tracer experiments were performed, all during very unstable meteorological conditions. The tracer was released and sampled at roof level in arcs up to 1.6 km from the tracer release. A considerable amount
Sven-Erik Gryning and Ekaterina Batchvarova
16
of information on the meteorology over the urban area is available. The data for the tracer experiments are available in Gryning et al. (2005).
3. Plume dispersion and urban areas
The study is based on well-known and commonly used semi-empirical estimates that as starting point take Taylor’s famous formula for plume dispersion: t t sz ¼ sw tf z (4) sy ¼ sv tf y Ty Tz where t is travel time of the plume and fy and fz are functions of the dimensionless travel time where Ty and Tz are Lagrangian time scales for the lateral and vertical dispersion processes. The approximations fy ¼
sffiffiffiffiffiffiffiffi!1 t 1þ 2T y
fz ¼
1þ
rffiffiffiffiffiffiffiffi1 t 2T z
(5)
are often recommended for applied dispersion modelling (Gryning et al., 1987). For ground-level sources Ty ¼ 200 s is recommended and Ty ¼ 600 s for elevated sources and when the vertical extent of the plume is larger than 10% of the depth of the mixing layer, for unstable atmospheric conditions Tz ¼ 300 s. 3.1. Lateral dispersion
The simulation of the lateral spread is performed in two ways. Firstly, the observed sv values (Copenhagen at 115 m and BUBBLE at 31.7 m) are used. Figure 4 shows the measurements and model simulations of sy from the Copenhagen experiment, using measured values of sv (left panel) and parameterized values (right panel). In both cases the agreement with the measurements is within a factor of 2. The analysis for the BUBBLE experiments is illustrated in Fig. 5. Simulations were performed for both Ty ¼ 200 s, which is the recommended value for ground level sources, and Ty ¼ 600 s as suggested for plumes larger than 10% of the mixed layer height. Both values of Ty in combination with the observed sv provide fair estimates of the lateral spread with the better given by Ty ¼ 600 s. This suggests that over urban areas the plume behaves more like from elevated than a low-level source.
Turbulence, Atmospheric Dispersion and Mixing Height 800 y (parameterisation of v)
800 Copenhagen
y (measured v)
17
600 400 200 0 0
Copenhagen
600 400 200
200 400 600 800 Measurements of y
0 0
200 400 600 800 Measurements of y
Figure 4. Measured and modelled values of sy for the Copenhagen experiment. The left panel shows simulations based on measurements of sv at 115 m. The right panel shows simulations using parameterized values of sv, also at 115 m. The lines show the 1:1 relationship and its factor of 2 range.
800 Parameterised y (m)
Parameterised y (m)
800 600 400 200
600 400 200 0
0 0
200
400
600
Measurements of y (m)
800
0
200 400 600 800 Measurements of y (m)
Figure 5. Measured and modelled values of sy for the BUBBLE tracer experiment for Ty ¼ 600 s (filled circles) and Ty ¼ 200 s (crosses). Left panel shows simulations based on measurements of sv at 31.7 m. The right panel is obtained using parameterized values of sv, also at 31.7 m. The lines show the 1:1 relationship and its factor of 2 range.
3.2. Maximum concentrations
Here we apply a very simple modelling approach to the very complex dispersion process of the urban area. For the Gaussian plume model, the ground-level centreline concentration Cmax(x) at downwind distance x can be expressed as Q h2 exp 2 C max ðxÞ ¼ 2sz psy sz u
(6)
C max (measured v and w)
20 16 12 8 4 0 0
4
8 12 16 C max measured
20
C max (parameterisation of v and w)
Sven-Erik Gryning and Ekaterina Batchvarova
18
20 16 12 8 4 0 0
4
8 12 16 C max measured
20
Figure 6. Measured and modelled normalized values of the maximum concentrations for the Copenhagen experiment. The left panel shows simulations based on hourly measurements of sv and sw at 115 m. The right panel is obtained by using parameterized values of sv and sw, also at 115 m. The lines show the 1:1 relationship and its factor of 2 range.
where h is the tracer release height, and Q the release rate. Figure 6 illustrates the results from a comparison between model simulations and measured tracer concentrations from the Copenhagen experiment. The measured arc-wise maximum concentration has been compared to the modelled centreline concentration. The values of sy and sz were derived from expressions (4) and (5), respectively, using Ty ¼ 600 s and Tz ¼ 300 s. The left panel in Fig. 6 illustrates the comparison when the measured values of sv and sw were applied in the expressions for sy and sz. The right panel refers to the case when the parameterized values of sv and sw were applied. The agreement can be seen to be within a factor of 2. A somewhat similar comparison is shown for the BUBBLE tracer experiment conducted on 26 June (Fig. 7), being the only one of the four tracer experiments with a well-developed tracer plume that is covered by the tracer sampling network. Because it is a low-level release, an even more simple modelling approach as compared to the Copenhagen experiment is used. Inserting the near-field expressions for sy and sz: x x sz ¼ sw (7) sy ¼ sv u u in the Gaussian plume formula, the ground level concentration at the centreline (maximum) Cmax at a given downwind distance x can be expressed as C max ðxÞ ¼
Qu psv sw x2
(8)
100
100
80
80
Prediction of C max
Prediction of C max
Turbulence, Atmospheric Dispersion and Mixing Height
60 40 20 0
19
60 40 20 0
0
20 40 60 80 100 Measurements of C max
0
20
40
60
80
100
Measurements of C max
Figure 7. Measured and modelled values of the maximum concentrations for the BUBBLE tracer experiment conducted on 26 June. Left: Simulations based on measurements of sv and sw at 31.7 m. Right: Simulations using parameterized values of sv and sw, also at 31.7 m.
where Q is the tracer release rate. Input to the model is measurements of sv, sw and wind speed u at a representative height for the dispersion of the plume. The maximum tracer concentrations are drawn from two arcs about 700 and 1200 m from the tracer source. Input to the model is half-hourly observations of sv, sw and the wind speed at a height of 31.7 m. The lines show the 1:1 relationship and its factor of 2 range. Concentration units are in ng m3 with a tracer release rate of 0.0503 g s1. Figure 7 shows the comparison between the maximum observed and predicted half-hourly tracer concentration in the two sampling arcs during the experiment conducted on 26 June. It can be seen that 11 out of 12 half-hourly concentrations fall within the range of a factor of 2. 4. Concluding remarks
We have applied simple models for the lateral and vertical atmospheric dispersion in an urban environment and found an agreement of about a factor of 2 between model results and measurements. This result is very promising when considering the complex structure of the urban boundary layer.
ACKNOWLEDGMENT
The authors are thankful to the BUBBLE community, and especially to Dr. Mathias Rotach (Meteo Swiss), Dr. Roland Vogt and Andreas
20
Sven-Erik Gryning and Ekaterina Batchvarova
Christen (University of Basel) for the discussions on the tracer experiment results. This study was supported by NATO (ESP.EAP.EV 981781) and the EU FP6 ACCENT Network of Excellence. REFERENCES Batchvarova, E., Gryning, S.-E., 2006. Progress in urban dispersion studies. Theor. Appl. Climatol. 84, 57–67. Gryning, S.-E., Batchvarova, E., Rotach, M., Christen, A., Vogt, R., 2005. Roof-level SF6 tracer experiments in the city of Basel. Verlag Institut fu¨r Atmospha¨re und Klima ETH, Zu¨rich. (Zu¨rcher Klima-Schriften, 83) p. 97. Gryning, S.-E., Holtslag, A.A.M., Irwin, J.S., Sivertsen, B., 1987. Applied dispersion modelling based on meteorological scaling parameters. Atmos. Environ. 21, 79–89. Gryning, S.-E., Lyck, E., 1984. Atmospheric dispersion from elevated sources in an urban area: Comparison between tracer experiments and model calculations. J. Climate Appl. Meteorol. 23, 651–660. Gryning, S.-E., Lyck, E., 2002. The Copenhagen tracer experiments: Reporting of measurements. Risø-R-1054(rev.1)(EN) p. 74 (only available on the Internet: www. risoe.dk/rispubl/VEA/ris-r-1054_rev1.htm). Rotach, M.W., Gryning, S.-E., Batchvarova, E., Christen, A., Vogt, R., 2004. Pollutant dispersion close to an urban surface—BUBBLE tracer experiment. Meteorol. Atmos. Phys. 87, 39–56.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06013-5
21
Chapter 1.3 Inverse modeling of local surface emissions with the CHIMERE-adjoint model: The case of the Paris area during the ESQUIF field experiment L. Menut, I. Pison and N. Blond Abstract The aim of this study is to define, test and apply a methodology to optimize surface emissions of anthropogenic species such as NOx at a local scale by using routine measurements of the air quality monitoring networks (measurements available in numerous areas and for long periods). A new methodology in which analyzed maps of concentrations obtained through a kriging technique are used as constraints for the inversion is proposed. The methodology is tested and applied to the Paris area because (i) the kriging technique has been developed for and first applied to this area because of the fully developed AIRPARIF measurement network and (ii) the layout of the area is representative of a simple type of large urbanized area. The NOx emission fluxes were particularly studied because (i) they are ozone precursors with large uncertainties, particularly in their 24-h time profile (Vautard et al., 2003) and (ii) they are directly linked to NO concentrations that are measured by AIRPARIF and can be analyzed by kriging.
1. Modeling system
The principle of the proposed inversion methodology is displayed on Fig. 1. The optimized concentrations provided by the inverse are used to perform a new kriging analysis. The new analyzed concentrations are then used as constraints for a second inversion. This gives the possibility of refining the results of the optimization by iterating several kriging-inversion cycles. The cost function to be minimized is in the form of J(e) ¼ (ysimya)T 1 R (ysimya) where ya contains the analyzed concentrations, corresponding
22
L. Menut et al.
Figure 1. Flowchart of the modeling system.
to each simulated concentration in ysim, and R is taken to be diagonal since the kriging technique does not provide the extra-diagonal terms. Note that information on the first-guess inventory is included in the analyzed concentrations. Therefore, this formulation of J avoids the problem of estimating a ‘‘background’’ matrix. Our modeling system is based on CHIMERE chemistry-transport model (Vautard et al., 2001) and its adjoint (Menut et al., 2000a; Menut, 2003). The adjoint approach was chosen because it makes it easy to take the trajectory of the model into account and perform 4D-integration. The kriging technique used here is called ‘‘INK’’ and has been developed by Blond et al. (2003). At any given hour, for any location s, the analysis ya(s) is a correction of the CHIMERE simulation yb(s) by a linear combination of the innovations yo(sk)yb(sk), where sk, k ¼ 1,y,K are the locations of the K measurement values yo(sk) provided by the network monitoring stations. The INK technique and CHIMERE are used by the Paris area air quality network, AIRPARIF, to produce daily maps of air quality forecasts (www.airparif.org). The minimizer called by the inverse code is N1QN3 (Gilbert and Lemare´chal, 1989).
Inverse Modeling of Local Surface Emissions
23
2. The pollution event of the 7th of August 1998
On the second day of the Intensive Observation Period (IOP) 2 of the Atmospheric Pollution Over the Paris Area (ESQUIF) campaign, a local photo-oxidant pollution event occurred (Menut, 2003), in which the local emissions play a major role (Menut et al., 2000a). An ozone plume developed in the Southwest of Paris and the difference between upstream and downstream ozone concentrations due to local emissions was at least 50 ppb. The event was simulated with the forecast version of CHIMERE (25 25 cells over 11 vertical levels, covering a 150 150 km area). The emission inventory was elaborated by AIRPARIF for the summer of 1998 (described in details in Vautard et al., 2003). It gives the hourly 6 6 km fluxes of 16 anthropogenic emitted species among which NOx speciated in 10% of NO2 and 90% of NO. The studies led during the ESQUIF campaign have shown that ozone concentrations simulated in the afternoon plume were underestimated by around 8%. In parallel, NO concentrations simulated downtown during the morning were overestimated as compared to measurements, particularly between 6 and 10 am (Menut et al., 2000b).
3. Application to the real case 3.1. The inverted problem: spatial aggregation
Considering the possible link between ozone and NO miss-estimations, NOx emissions from 3 to 10 am are inverted, assuming that (i) the distribution inside the family remains unchanged (ii) all the other parameters and parameterizations are perfect or at least do not explain the discrepancies between simulation and measurements. To better satisfy the latter assumption, the BLH, that was found to be underestimated by the meteorological data used by the model as compared to measurements made during the field campaign, has been corrected to match the more reliable data. Since the number of individual fluxes is very high, it is necessary to reduce the size of the problem to match the available quantity of information. First, fluxes less than 5 1011 molecules cm2 s1 located in the rural areas surrounding the domain are not inverted. Then, zones are defined to aggregate the fluxes to be inverted. In each zone, the same correction is applied to all the aggregated fluxes. In order to satisfy this assumption, the zones are defined by taking into account (i) the intensity of the emission fluxes and (ii) the sensitivity of the concentrations to these
24
L. Menut et al.
Figure 2. Principle of spatial aggregation.
emissions. This leads to a dynamical spatial aggregation that makes use of the a priori information available in the emission space. A simple example of aggregation is shown on Fig. 2: the four big zones are broken into smaller ones acknowledging for the gradient of intensity in the emission fluxes. 3.2. Results 3.2.1. Spatial distribution of corrections
The inversion time-window ranging from 3 to 10 am, the spatial distributions of the corrections at 5 and 8 am are displayed on Fig. 3. This shows that the pattern of corrections in not homogeneous, neither in time nor in space. At 5 am, after the optimization, the most intense fluxes located downtown are decreased (multiplied by 0.5–0.75) whereas the intense fluxes located outside the city upstream are increased (multiplied by 1.25–2.75). On the contrary, at 8 am, the most intense fluxes are almost unchanged by the optimization with corrections less than 5% whereas less intense fluxes located outside the city are decreased (multiplied by 0.75–0.95). Since the situation differs according to the location, the time evolution of the optimized fluxes is studied for two locations representative of the results obtained downtown and in the suburbs. 3.2.2. Optimized emissions downtown
The time evolution of NO emissions in the city are displayed on Fig. 4 for the Southwest part of Paris that is representative of the whole town. The morning emission peak is reduced from 5 h long (from 5 to 9 am) to only 2 h long (from 8 to 9 am). Since (i) the time profile of the optimized emissions does not show oscillations and (ii) the decrease in intensity is
Inverse Modeling of Local Surface Emissions
25
Figure 3. Spatial distribution of corrections.
consistent with the fact that the first-guess inventory has actually been built for July 1998 (traffic is generally lighter in August in the Paris area), the inversion methodology seems to be reliable for real studies. 3.2.3. Optimized emissions in the suburbs
Four fluxes located in the suburbs upstream Paris were hugely corrected (shown in orange on Fig. 3) for 1 or 2 h. The time evolution of NO emissions is displayed on Fig. 4 for Tremblay that is representative of these suburban fluxes.
26
L. Menut et al.
Figure 4. Time evolution of first-guess and optimized NO emissions.
If the peak in the optimized emissions is correctly timed as compared to the measured concentrations, its intensity (more than 4.75 1012 molecules cm2 s1) seems unrealistic. It was then assumed that the optimized peak corresponds to a real traffic peak, that has been measured but not
Inverse Modeling of Local Surface Emissions
27
Figure 5. Difference (ppb) between optimized and first-guess ozone concentrations.
simulated and was maybe due to departures on holiday, but the intensity of which is exaggerated probably because of a lack of representativity of the constraints. This problem, which arises for only four isolated fluxes, may indicate that the realism of the corrections decreases with the density of the measurement network. 3.2.4. Impact on ozone concentrations
To validate optimized emissions, their impact on ozone concentrations is examined. Figure 5 presents ozone concentrations simulated in the afternoon plume at 3 pm, which are increased by less than 5% by NOx emissions optimized in the city during the morning. Nevertheless, since first-guess ozone concentrations were underestimated by 8%, the optimization thus reduces the underestimation to only 3.5%. This shows that the inversion is able to lead to a better simulation of key events.
4. Conclusion
A new inversion methodology has been designed. It uses an iterative scheme calling on a kriging technique to generate the constraints.
28
L. Menut et al.
Focusing on the Paris area and NOx emission fluxes, it is shown that the constraints provided by kriging make it possible to retrieve an emission inventory with a good accuracy, for a wide range of quality of measurements and first-guess inventories. The new methodology is applied to the pollution event that occurred on the 7th of August 1998, second day of the IOP 2 of the ESQUIF field campaign. A dynamic spatial aggregation technique has been specially elaborated to further reduce the size of the problem. The optimization of NOx emissions has particularly lead to a reduction of the duration of the morning peak and to a decrease of the underestimation of ozone concentrations in the plume. An operational limitation has nevertheless been encountered: the reliability of the results decreases with the density of the measurement network, which explains that ozone measurements cannot be used presently. The prospects of this work include (i) a quantification of the uncertainty on optimized inventories, possibly by interacting with Monte-Carlo simulations, (ii) the application to other areas and (iii) the use of satellite data instead of/together with surface data.
Discussion
T. Odman:
L. Menut:
P. Builtjes:
I thought you were using this approach in forecasting. I must have misunderstood but I will ask the question anyway. Given that you are only associating errors with emissions, if you were using this approach for forecasting would you select a day from the past with meteorology similar to the forecasting day or just use the previous day’s corrected emissions? The best use of this methodology is in the framework of past events analysis. We are not using this approach in forecast mode but this is in the course: the goal is to inverse the emissions of the day before in order to rerun the model with ‘‘optimized emissions’’ and, thus, to have ‘‘best’’ modeled chemical concentrations fields to initiate the forecast model simulation. Is there a limit to the improvement of the errors in the emission by inverse modeling, and would that be in the order of 20%?
Inverse Modeling of Local Surface Emissions
L. Menut:
E. Genikhovich:
L. Menut:
B. Physick:
L. Menut:
29
It is very difficult to answer this interesting question. This type of percentage depends on the source types, the studied domain, the studied time periods and thus their corresponding characteristics (extreme event, usual polluted situationy). We agree with P. Builtjes for our specific study over the Paris area but over several months the improvement of errors in the emissions is certainly more or less 20%. In your approach, all the discrepancies between model and measurement results are attributed to the errors in emissions. Such an approach could be applied to any model, even simple Gaussian ones with linear chemistry, for example. How can you be sure that your corrected emissions are realistic if they strongly depend on the error of the model etc.? For the first part of the question: Yes, the discrepancies between model and measurements are all attributed to potential lacks in emissions but only after a systematic debiasing of the other input parameters such as boundary conditions, boundary layer height and temperature (on an hourly basis). The corrected emissions depend on the model error (this is the main hypothesis in inverse modeling whatever the studied problem and the model used). We think that our corrected emissions are realistic because: (i) the modeled concentrations fields of various species (and not only one) are better, (ii) this latter point is true for a long period whatever the meteorological situation, the location of the measurements station within the studied domain, i.e., the whole Paris area (including urban, suburban and rural areas). If you are primarily interested in ozone forecasting, you will have to adjust the VOC emission fluxes as well as the NOx fluxes. Have you done any work on this? Of course, there would be less routine measurements and the VOC flux dependence on temperature is an additional complication. No, the work is not already done for VOCs. The reasons are mainly (i) our first goal was to
L. Menut et al.
30
elaborate a new methodology, (ii) to achieve this, we select the most uncertain source i.e., the traffic (and thus NOx) over Paris, (iii) our sensitivity tests about the minimum number of required measurements versus the model grid cell numbers to be inverted showed that not enough measurements are available for VOCs.
ACKNOWLEDGMENTS
This work was done under a TOTAL-CNRS grant and in the framework of the PRIMEQUAL2 project OPTEMI supported by the French Ministry of Environment. REFERENCES Blond, N., Bel, L., Vautard, R., 2003. Three-dimensional ozone data analysis with an air quality model over the Paris area. J. Geophy. Res. 108(D23), 4744. Gilbert, J.-C., Lemare´chal, C., 1989. Some numerical experiments with variable-storage quasi-Newton algorithms. Math. Prog. 45, 407–435. Menut, L., 2003. Adjoint modelling for atmospheric pollution processes sensitivity at regional scale during the ESQUIF IOP2. J. Geophy. Res. 108(D17), 8562. Menut, L., Vautard, R., Beekmann, M., Honore´, C., 2000a. Sensitivity of photochemical pollution using the adjoint of a simplified chemistry-transport model. J. Geophy. Res. 105(D12), 15379–15402. Menut, L., Vautard, R., Flamant, C., Abonnel, C., Beekmann, M., Chazette, P., Flamant, P.H., Gombert, D., Gue´dalia, D., Lefebvre, M.P., Lossec, B., Martin, D., Me´gie, G., Perros, P., Sicard, M., Toupance, G., 2000b. Measurements and modelling of atmospheric pollution over the Paris area: An overview of the ESQUIF Project. Ann. Geophys. 18(11), 1467–1481. Vautard, R., Beekmann, M., Roux, J., Gombert, D., 2001. Validation of a hybrid forecasting system for the ozone concentrations over the Paris area. Atmos. Env. 35(14), 2449–2461. Vautard, R., Martin, D., Beekmann, M., Drobinski, P., Friedrich, R., Jaubertie, A., Kley, D., Lattuati, M., Moral, P., Neininger, B., Theloke, J., 2003. Paris emission inventory diagnostics from ESQUIF airborne measurements and a chemistry transport model. J. Geophy. Res. 108(D17), 8564.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06014-7
31
Chapter 1.4 Numerical simulations of microscale urban flow using the RAMS model Tamir Reisin, Orit Altaratz Stollar and Silvia Trini Castelli Abstract The RAMS model, in its latest version (V6), is used to simulate the flow around a set of buildings with a resolution of 1-2 meters in all directions. The k-e and k-e RNG turbulence parameterization were implemented in the RAMS model. The first one is commonly used in urban environments, however it was found to have some deficiencies when applied to the simulation of flow impingement and separation. The second parameterization is found to overcome these deficiencies. Results show that the flow that develops around the buildings simulated in the present work is notably complex and was found to be sensitive both to the turbulence closure scheme and to the boundary conditions as specified at the buildings’ walls. 1. Introduction
There is renewed interest in urban dispersion modeling due to the need for tools that can be employed for responding to, planning for, and assessing the consequences of an airborne release of toxic materials potentially threatening to human life. Releases of hazardous gases and aerosols may result from on-site accidents as in the case of industrial chemical releases, occur during transport of hazardous chemicals as in tanker truck or railroad spills, or may be premeditated as in a chemical, biological, or radiological agent terrorist attack (Brown, 2004). Although, the dispersion models perform well in open terrain, additional work is required in order to predict dispersal in urban environments (Davis and Prosnitz, 2003), and in particular to make the operational models accurate enough that first responders can make decisions on protective intervention with a reasonable degree of confidence.
32
Tamir Reisin et al.
Transport and dispersion in urban environments is extremely complicated and modeling atmospheric flows and pollutant dispersion over urban areas is a problem of unique characteristics. Buildings alter the flow field, causing updrafts and downdrafts, channeling between buildings, areas of calm winds adjacent to strong winds, horizontally and vertically rotating eddies between buildings, at street corners, and other places within the urban canopy (Hosker, 1984). Accounting for the impacts of buildings on the transport and dispersion is crucial in estimating the travel direction, areal extent, toxicity levels of the contaminant plume, and the extent of population exposure (Brown, 2004). The airflow around buildings involves impingement and separation regions, building wakes with multiple vortices, interference from adjacent buildings and jetting effects in street canyons. Thus, accurate simulations of building-scale transport and dispersion require appropriate physics sub-models and also significant computing resources, making its numerical modeling a challenging task (Chan et al., 2000). Urban emissions occur mainly within or shortly above the canopy layer, i.e., within a zone where the atmospheric flow is heavily disturbed by buildings and other obstacles. In comparison to unobstructed terrain, building effects can change local concentrations by more than an order of magnitude. As a consequence, it is inappropriate to consider only buildings within a surface roughness parameterization, particularly on the scale of a few streets or city blocks (Schatzmann and Leitl, 2002). The urban scales span a large range, from the microscale characteristic of the physical processes in a street canyon (1–10 m) to the regional scale through the city scale (tens of km), so that buildings and complex terrain are to be considered simultaneously to characterize the city’s inhomogeneities. The interaction of the urban site with atmosphere complicates boundary layer variables, which require specific studies, since the urban small-scale fluid dynamics superposes to the atmospheric mesoscale flow and turbulence. Thus, in order to treat the urban modeling problem in a comprehensive way, a merging of the characteristics and performances of atmospheric models and complex geometry fluid-dynamics models is necessary. This article presents the work performed, thus far, on the modeling of the microscale flow, in the framework of a collaboration for the development of a modeling system for urban air pollution, which encompasses the simulation of all relevant scales: synoptic, mesoscale, and the urban microscales. The main purpose of the project at this initial stage was to adapt the regional atmospheric modeling system (RAMS) atmospheric model to simulate the flow around buildings.
Numerical Simulations of Microscale Urban Flow Using the RAMS Model
33
2. The numerical model
The RAMS is a well-known and worldwide used atmospheric model, simulating atmospheric circulations ranging in scales from an entire hemisphere down to eddies in the planetary boundary layer. A comprehensive review of the RAMS model can be found in Pielke et al. (1992) and Cotton et al. (2003). In the latest version of RAMS (RAMS6.0), an alternative option to the traditionally employed terrain-following coordinates makes possible the use of a Cartesian grid extending from sea level to the model top. In this coordinate system, low elevation grid cells are completely or partially submerged beneath elevated topography. The new approach, called ADAP (or ADaptive APerture), allows for arbitrarily steep and even overhanging topography. This method is especially suitable for application such as flow around buildings (Walko and Tremback, 2002). This version of RAMS enables simulation with very high resolution (several meters) of the flow in an urban environment. The standard RAMS model includes turbulence parameterizations that are suitable to atmospheric flow (e.g., Mellor and Yamada 2.5). In urban environments, turbulence models of the kind k–e have been commonly used. In recent years, a standard version of the k–e turbulence closure model was implemented and tested in RAMS (Trini Castelli et al., 1999, 2001, 2005; Ferrero et al., 2003). This scheme, even though widely used, has some deficiencies when applied to the simulation of flow impingement and separation (Castro and Apsley, 1997). An improved model has been developed by Yakhot and Orszag (1986) that applied the renormalization group method to the Navier-Stokes equations and the equations of passive scalar to evaluate turbulence statistics. This is called the renormalization group (RNG) k–e turbulence model. The principal idea of the RNG method lies in the systematic removal of small-scales of turbulence by representing their effects in terms of larger scale motions and a modified viscosity (Yakhot et al., 1992). In the present work, we implemented in RAMS the formulation of the RNG k–e scheme as suggested by Kim and Baik (2004). The Reynolds stresses and turbulent fluxes in the Navier-Stokes equations and in the transport equation for a passive scalar are parameterized in terms of grid resolvable variables on the basis of the K-theory as @U i @U j 2 dij k þ (1) ui uj ¼ K m 3 @xj @xi
Tamir Reisin et al.
34
and cuj ¼ K c
@C @xj
(2)
where Ui is the ith components of the mean velocity, C is the mean concentration of any passive scalar (e.g., a pollutant), and ui and c the fluctuations from their respective means. Km and Kc are the turbulent viscosities of momentum and pollutant concentration respectively, dij the Kroenecker delta, and k the turbulent kinetic energy (TKE). In the RNG k–e turbulence scheme, Km is given by !2 1=2 Cm k (3) Km ¼ n 1 þ n 1=2 where Cm is an empirical constant. This last expression for Km includes molecular kinematic viscosity as well. The value for Kc is calculated from the Schmidt number Sc ( ¼ Km/Kc) that is specified as 0.9. The RNG k–e turbulence scheme as presented by Yakhot et al. (1992) differs from the standard k–e turbulence scheme in that it includes an additional sink term in the turbulence dissipation equation to account for non-equilibrium strain rates, and employs different values for the model coefficients. The prognostic equations of TKE and its dissipation rate can be written as @k @k @U i @ K m @k (4) ¼ ui uj þ þ Uj @xj @xj sk @xj @t @xj @ @ @U i @ K m @ 2 þ Uj C 2 R ¼ C 1 ui uj þ @xj @xj s @xj k @t @xj k
(5)
where sk, se, Ce1, and Ce2 are empirical constants. The last term in the last equation is an extra strain rate term given by C m Z3 ð1 Z=Z0 Þ2 ð1 þ b0 Z3 Þk
(6)
@U i @U j @U i 1=2 þ @xj @xi @xj
(7)
R¼ where k Z¼
The constants in the parameterization scheme were set as ðC m ; sk ; s ; C 1 ; C 2 ; b0 ; Z0 Þ ¼ ð0:0845; 0; 7179; 0:7179; 1:42; 1:68; 0:012; 4:377Þ Special consideration was given to the near-wall region flow, to account for the influence of walls’ friction on the flow and for the heat fluxes from
Numerical Simulations of Microscale Urban Flow Using the RAMS Model
35
buildings’ walls. For this purpose, in this initial work we have chosen for a simplified approach to determine the boundary conditions at the building faces. An ‘‘influence region’’ was defined around the buildings, in which the walls affect the values of the dynamic and thermo-dynamic atmospheric variables of wind and temperature. In the influence region, a logarithmic interpolation between the values at the building face and the values of the variable in the ambient atmosphere near the buildings was imposed. For the wind velocity components, the no-slip condition was used for the tangential component. For the temperature, the logarithmic interpolation is between the value of the temperature at the building faces, and the atmospheric values at the second grid points closest to the building faces. For the turbulence variables k and e, we imposed null values at the grid points identified as the building faces. Then, as analogously done for the first level close to the ground, a boundary condition derived from the surface layer similarity theory is imposed at the first atmospheric grid points proximate to the building faces as follows: u2n Cm
(8)
u3n KC m
(9)
kbc ¼ and bc ¼
where u* is the friction velocity and K is the von Karman constant. 3. Model and simulation setup
The RAMS model was used to simulate atmospheric flow in the surroundings of Igud Arim Ashdod (IAA, Regional Environmental Authorities) building in the city of Ashdod, Israel. The location was chosen because it is a relatively isolated building in an industrial zone and is a candidate for a future field campaign of tracer measurements. The buildings complex includes an upside down U-shape building 9 m height and a 15 m height building to its south (see Figs. 3 and 4 for a plan view). Two sets of test simulations were performed. In the first, corresponding to a nighttime simulation on September 3, 2004, a qualitative comparison between the standard k–e and the RNG-k–e closure simulations was conducted. The meteorological situation was a ground inversion with southwesterly wind with a speed around 1 m s1 at the buildings’ height. The second set of simulations was devoted to an analysis of the effects of the buildings’ temperature on the flow. The nighttime development of
36
Tamir Reisin et al.
atmospheric conditions was simulated for December 3, 2004, corresponding to a synoptic situation of a high pressure over Israel with northeasterly winds and a stable atmosphere. During nighttime the effect of the buildings’ temperature on the wind field is expected to be more significant because the atmosphere is more stable and calmer than during the day. Two runs were conducted; in the first the temperature of the buildings’ walls was set to 51C and in the second to 201C. According to the initial conditions, corresponding to the profiles provided by larger scale RAMS simulations at IAA grid point and used as a homogeneous base state environment, the surrounding temperature of the air at 1 m was 11.51C, and the ambient wind speed at the buildings heights was between 1 and 2 m s1. Some preliminary simulations were conducted in order to find a spatial resolution that enables resolution of the main characteristics of the flow. Since the narrowest ‘‘flow channel’’ in the domain was around 6 m, a resolution of 1 m was found to be sufficient to appropriately describe the local flow (including the description of vortices development) while maintaining affordable computation times. Therefore, the simulations were conducted with a spatial resolution of 1 m in the horizontal directions, the vertical resolution was of 1 m up to a height of 20 m (5 m higher than the highest building), and then it was gradually increased up to 10 m between 130 m and 230 m height. The horizontal domain was 120 m in the x direction and 140 m in the y direction. The time step was automatically set by RAMS in order to maintain numerical stability (around 0.01 s).
4. Results
Figures 1 and 2 show XZ cuts for both wind and TKE fields for the first set of calculations, following 3.5 min of model simulation. The cut is at the middle of the domain in the Y direction (see Figs. 3 and 4). The figures show relatively consistent differences when using the k–e or the RNG-k–e closure models. The main characteristics of the mean flow and turbulence, like the horizontal and vertical vortices between the two buildings and the reverse flow and recirculation over the roof of the western building, are similar, but a rather different energy distribution is produced. In fact, the k–e model transfers more energy from the mean flow to turbulence, generating consistently higher values of TKE than with the RNG-k–e closure, which shows larger values for the wind speed. We notice that already at 1 m resolution, both closures are able to produce flow separation at the front corner of the impact building and
Numerical Simulations of Microscale Urban Flow Using the RAMS Model
37
Figure 1. k–e closure scheme, wind vectors and turbulent kinetic energy after 3.5 min of simulation.
38
Tamir Reisin et al.
Figure 2. RNG-k–e closure scheme, wind vectors and turbulent kinetic energy after 3.5 min of simulation.
Numerical Simulations of Microscale Urban Flow Using the RAMS Model
39
Figure 3. Horizontal and vertical wind vectors after 5 min of simulation with walls temperature of 51C.
40
Tamir Reisin et al.
Figure 4. Horizontal and vertical wind vectors after 5 min of simulation with walls temperature of 201C.
Numerical Simulations of Microscale Urban Flow Using the RAMS Model
41
reverse flow on the roof, while this was found to be occasionally a problem with standard k–e in Kim and Baik (2004). Figures 3 and 4 show wind vectors for the second set of simulations. Figure 3 corresponds to the case with walls’ temperature of 51C and Fig. 4 for the 201C case. The bold line in XY plane shows the location of the vertical XZ cut, and the horizontal cut is at 5 m height. In the following discussion the focus is on the flow characteristics along the passage between the northern buildings and the southern one. The effect of the walls’ temperature on the surrounding flow was very significant, as not only the wind speed was different but the flow direction was completely different in the region of interest. Because of the stable atmosphere at nighttime, the impact of the cool walls (51C) was more distinct. It was characterized by the relatively strong downdrafts that developed. The effect of the warm walls (201C) was dumped by the atmospheric stability. Regarding the 51C case, the northeasterly air flowing along the roofs of the buildings cools down and sinks at the southern/western faces of the buildings. At the eastern buildings, the air sinks at the gap with the southern building and the cooling effect is increased due to the effect of the surrounding walls around the narrow passage and the downdrafts increase. These downdrafts diverge at the surface resulting in horizontal winds at different directions on both sides of the passage. On the western side the easterly winds along the passage are enhanced when they encounter the easterly component of the downdrafts coming from the western building’s roof. The maximum horizontal wind speed at 5 m height reached 1.2 m s1 at the western outlet of the passage and about 0.9 m s1 on the eastern outlet. The maximum downdrafts were of the order of 1 m s1. In the 201C case the air flowing along the roofs is expected to warm up; therefore, downdrafts are not expected to develop. Updrafts along the walls are weak because of the nighttime stable atmosphere. The air that flows along the eastern face of the eastern building enters the passage between the buildings producing an easterly wind within it. The wind slows down towards the western outlet and encounters a westerly component resulting in a vortex at the southwestern corner of the western building. The flow in the passage is mainly horizontal at the eastern side while an updraft appears on the western side due to convergence with the flow coming from that direction. The maximum horizontal wind speed at the passage was reached between the eastern building and the southern one and was of the order of 1 m s1; on the western side it was considerably lower being around 0.5 m s1. The updrafts that appear between the two buildings were lower than 0.5 m s1, while those on the western side of the buildings were larger than 1 m s1.
42
Tamir Reisin et al.
5. Conclusions
The latest version of the RAMS model was found to be suitable to simulate the flow around buildings. The flow that develops around the buildings simulated in the present work is notably complex and was found to be sensitive both to the turbulence closure scheme and to the boundary conditions as specified at the buildings’ walls. Obviously, the impact of the changing flow and turbulence characteristics on pollutants dispersion is expected to be significant. Efforts in the next stages of this research will be devoted primarily to a more quantitative comparison between the two turbulent models and then to issues related to boundary conditions. A criterion to establish the length scales of the IR needs to be found, on the basis of possible studies of the effects of the building presence on the environment. The introduction of boundary conditions derived by the similarity theory and the correspondent variables’ profiles depending on the stability will be considered. In the present case, the main similarity parameters need to be redefined in order to properly account for the influence of the building. Alternatively, the boundary conditions at the building walls could be defined computing the momentum flux on the basis of the shear and a drag coefficient and the heat flux on the basis of heat transfer laws.
REFERENCES Brown, M.J., 2004. Urban dispersion—Challenges for fast response modeling. AMS Conference on Applications of Air Pollution Meteorology. Castro, I.P., Apsley, D.D., 1997. Flow and dispersion over topography: A comparison between numerical and laboratory data for two-dimensional flows. Atmos. Environ. 31, 839–850. Chan, S.T., Stevens, D.E., Lee, R.L., 2000. A model for flow and dispersion around buildings and its validation using laboratory measurements, Proc. 3rd Symposium on the Urban Environment, 14–18 August, Davis, CA, pp. 56–57. Cotton, W.R., Pielke, R.A., Walko, R. Sr., Liston, G.E., Tremback, C.J., Jiang, H., McAnelly, R.L., Harrington, J.Y., Nicholls, M.E., 2003. RAMS 2001—Current status and future directions. Meteor. Atmos. Phys. 82, 5–29. Davis, J., Prosnitz, D., 2003. Technical and policy issues of counterterrorism—a primer for physicists. Phys. Today, April 2003, 39–44. Ferrero, E., Trini Castelli, S., Anfossi, D., 2003. Turbulence fields for atmospheric dispersion models in horizontally non-homogeneous conditions. Atmos. Environ. 37(17), 2305–2315. Hosker, R.P. Jr., 1984. Flow and diffusion near obstacles. In: Randerson, D. (Ed.), Atmospheric Science and Power Production, DOE/TIC-27601. U.S. Dept. of Energy, Washington, DC, pp. 241-326, Ch. 7.
Numerical Simulations of Microscale Urban Flow Using the RAMS Model
43
Kim, J.-J., Baik, J.-J., 2004. A numerical study of the effects of ambient wind direction on flow and dispersion in urban street canyons using the RNG k–e turbulence model. Atmos. Environ. 38, 3039–3048. Pielke, R.A., Cotton, W.R., Walko, R.L., Tremback, C.J., Lyons, W.A., Grasso, L.D., Nicholls, M.E., Moran, M.D., Wesley, D.A., Lee, T.J., Copeland, J.H., 1992. A comprehensive meteorological modeling system—RAMS. Meteorol. Atmos. Phys. 49, 69–91. Schatzmann, M., Leitl, B., 2002. Validation and application of obstacle-resolving urban dispersion models. Atmos. Environ. 36, 4811–4821. Trini Castelli, S., Ferrero, E., Anfossi, D., 2001. Turbulence closures in neutral boundary layers over complex terrain. Bound. Layer Meteorol. 100, 405–419. Trini Castelli, S., Ferrero, E., Anfossi, D., Ohba, R., 2005. Turbulence closure models and their application in RAMS. Environ. Fluid Mech. 5, 169–192. Trini Castelli, S., Ferrero, E., Anfossi, D., Ying, R., 1999. Comparison of turbulence closure models over a schematic valley in a neutral boundary layer. Proceeding of the 13th Symposium on Boundary Layers and Turbulence—79th AMS Annual Meeting, pp. 601–604. Walko, R., Tremback, C., 2002. The Adaptive Aperture (ADAP) Coordinate. 5th RAMS Workshop and Related Applications, Santorini, Greece. Yakhot, V., Orszag, S.A., 1986. Renormalization group analysis of turbulence. J. Sci. Comput. 1, 3–51. Yakhot, V., Orszag, S.A., Thangam, S., Gatski, T.B., Speziale, C.G., 1992. Development of turbulence models for shear flows by a double expansion technique. Phy. Fluids A 4, 1510–1520.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06015-9
44
Chapter 1.5 Assessment of dust forecast errors by using lidar measurements over Rome P. Kishcha, P. Alpert, A. Shtivelman, S.O. Krichak, J.H. Joseph, G. Kallos, P. Katsafados, C. Spyrou, G.P. Gobbi, F. Barnaba, S. Nickovic, C. Perez and J.M. Baldasano Abstract In this study, forecast errors in dust vertical distributions were analyzed. This was carried out by using quantitative comparisons between dust vertical profiles retrieved from lidar measurements over Rome, Italy, and those predicted by models. Three models were used: the four-particle-size Dust Regional Atmospheric Model (DREAM), the older one-particle-size version of the SKIRON model from the University of Athens (UOA), and the pre-2006 oneparticle-size Tel Aviv University (TAU) model. SKIRON and DREAM are initialized on a daily basis using the dust concentration from the previous forecast cycle, while the TAU model initialization is based on the Total Ozone Mapping Spectrometer aerosol index (TOMS AI). The quantitative comparison shows that (1) the use of four-particle-size bins in the dust modeling instead of only one-size bin improves dust forecasts, (2) cloud presence could contribute to additional dust forecast errors in SKIRON and DREAM, (3) as far as the TAU model is concerned, its forecast errors were mainly caused by technical problems with TOMS measurements from the Earth Probe satellite. As a result, dust forecast errors in the TAU model could be significant even under cloudless conditions. 1. Introduction
In order to evaluate the model capabilities for providing reliable forecast of 3D-dust distributions in the atmosphere, we used dust forecasts of three different forecasting systems: the four-particle-size Dust Regional Atmospheric Model (DREAM) (Nickovic et al., 2001), the pre-2006 one-particle-size Tel Aviv University (TAU) dust prediction system
Dust Forecast Errors by Using Lidar Measurements Over Rome
45
(Alpert et al., 2002), and the older one-particle-size version of the SKIRON model of the University of Athens (UOA) (Kallos et al., 1997). All these three model versions have their origin in the same predecessors described by Nickovic and Dobricic (1996), Kallos et al. (1997), and Nickovic et al. (1997), with various components upgraded afterwards. The dust forecasts were compared against lidar remote soundings over Rome, Italy (41.81N, 12.61E) performed over the 3-year period 2001–2003 (e.g., Gobbi et al., 2004). The full description of this study has been previously submitted for publication to the Journal of Geophysical Research (Kishcha et al., 2007).
2. Dust prediction system
The older version of SKIRON forecasting system of the University of Athens, used in this study, includes a dust module with the one-particle-size representation of dust aerosol (Kallos et al., 1997). This SKIRON system has been in operational use since 1998 providing 72-h weather and dust forecasts for the Mediterranean region. Dust is driven by the hydrostatic NCEP/Eta model (Mesinger, 1997). The SKIRON system covers a domain including the Mediterranean Sea, Europe, North Africa, and Middle East. In the vertical, 32 levels are using stretching from the ground to the model top (15,800 m). In the horizontal, a grid increment of 0.241 is applied. The system includes packages for dust initialization, transport, and wet/dry deposition, developed within the framework of the Mediterranean Dust Experiment (MEDUSE) EU project (Janjic, 1994; Nickovic and Dobricic, 1996; Nickovic et al., 1997). The dust module is dynamically coupled with the atmospheric model; therefore, at each time step, the prognostic atmospheric and hydrological conditions are used to calculate the effective rates of the injected dust concentration based on the viscous/turbulent mixing, shear-free convection diffusion, and soil moisture. Special care was taken to define as accurately as possible the dust productive areas since soil properties (soil structure, soil wetness, vegetation cover) dictate the dust quantity that may be available when the turbulent state of the surface atmosphere triggers its injection into the atmosphere. The specification of the model dust sources and the calculation of dust-related processes are obtained from high-resolution data sets of vegetation and soil texture types. For the geographical distribution of the land cover and the dust sources, Olson World Ecosystem Data of 10 min resolution and with 59 vegetation types are used. For the soil texture distribution, the UNEP/FAO data set is applied after its
46
P. Kishcha et al.
conversion from soil type to soil textural ZOBLER classes (Papadopoulos et al., 1997). The dust is considered as a passive substance, i.e., no dust feedback effects are included in the radiation transfer calculations. It should be mentioned that a new version of SKIRON has been developed at the University of Athens, which includes a dust module with the fourparticle-size representation of dust aerosol (Nickovic et al., 2001; Kallos et al., 2006). Being in operational use since January 2003, it has the same elements as DREAM described below, since their development was done in the framework of the SKIRON and MEDUSE and later the ADIOS projects. The one-particle-size SKIRON system, after modification, was put into operation and has been used for short-term dust predictions at TAU since November 2000 until the end of 2005 (Alpert et al., 2002). Several modifications were made to the model including development of a new dust initialization procedure, determination of the dust sources employing Ginoux et al.’s (2001) method, and expansion of the forecast area to include the Atlantic Ocean. These improvements were undertaken in order to support the joint Israeli–American Mediterranean Dust Experiment (MEIDEX). The model domain is 0–501N, 501W–501E. The model has a horizontal resolution of 0.51 and 32 vertical levels. Dust forecasts are initialized with the aid of the Total Ozone Mapping Spectrometer aerosol index (TOMS AI) measurements (Alpert et al., 2002). The initial dust vertical distribution over each grid-point, within the model domain, is determined according to the value of TOMS indices among four categories of model-calculated averaged dust profiles over the Mediterranean and among four other profiles over North Africa. The dust component is based on a single-particle-size bin with radius of 2–2.5 microns. The four-particle-size DREAM model incorporates the state-of-the-art parameterizations of all the major phases of atmospheric dust life such as production, diffusion, advection, and removal (Nickovic et al., 2001). In DREAM, the emission parameterization combines the flux scheme of Shao et al. (1993) and viscous sub-layer model of Janjic (1994). Its dust module includes effects of the particle-size distribution on aerosol dispersion. In particular, special attention was made in order to properly parameterize the dust production phase. Dust productive areas in the model are specified using the US Geological Survey (USGS) data of 30 s resolution on land cover. For each soil texture class the fractions of clay, small silt, large silt, and sand are estimated with four-particle-size radii of 0.7, 6.1, 18.0, and 38 microns, respectively. In DREAM, the dust cycle is described by a set of K-independent Euler-type concentration equations allowing no inter-particle interactions, where K ¼ 4 indicates the number of particle size class. The area covered by the model is 201W–451E and
Dust Forecast Errors by Using Lidar Measurements Over Rome
47
151N–501N. The model has a horizontal resolution of 0.31 and 24 vertical levels between the surface and 16,000 m. To compare the dust forecast with lidar-derived volume profiles, modeled mass concentration profiles over Rome were divided by dust density, assumed as 2.5 gcm3, in agreement with the majority of other dust models, e.g., Kinne et al. (2003, their Table 4). 3. Lidar data
Lidar measurements employed in this study were collected by a singlewavelength, polarization-sensitive lidar system (VELIS), operational since February 2001 in the ISAC laboratories (41.841N–12.641E, 130 m above sea level) at the outskirts of Rome. Measurements were carried out daily at non-synchronous times between 7 am and 9 pm (UTC). The lidar radiation source is a frequency-doubled Nd:YAG laser, emitting planepolarized pulses at 532 nm. The intensity and repetition rate of laser pulses are generally set as 30 mJ and 10 Hz, respectively. The system set up allows collecting the complete tropospheric backscatter profile between 300 m and 14 km from the ground. Backscattered light is recorded on either the parallel (//) or the perpendicular (?) polarization planes with respect to the laser one. Lidar profiles are obtained as 10-min averages and their vertical resolution is 37.5 m. A thorough description of the lidar signal analysis is given by Gobbi et al. (2002). The Barnaba and Gobbi (2001) approach was used in the current study to derive heightresolved dust volumes from lidar measurements of backscatter. In particular, comparisons between lidar data and in situ measurements showed a slight (1%) lidar tendency to underestimate desert dust volume, and an average agreement within 720% (Gobbi et al., 2003). Since those comparisons were performed in the near range portion of the lidar trace (lidar levelso500 m), we expect an additional random error to affect the farther ranges: 8% at 4–6 km and 30% at 6–8 km. In this study, the dust forecasts were compared against lidar data for 34 days taken randomly during the 3-year period 2001–2003, for the high dust activity season from March to June. Further details about the selected days are in Kishcha et al. (2005). Since this study was aimed at checking the quality of dust forecasts available at 12 UTC, the lidar profiles closest to 12 UTC were selected for the analysis. 4. Quantitative inter-comparison
The correspondence between model data and lidar measurements over Rome is evaluated by means of scatter plots with lidar-derived versus
P. Kishcha et al.
48
model-simulated dust volumes (not shown). Examples of such scatter plots are in Kishcha et al. (2005). The bisector curves indicate ideally accurate forecasts, i.e., the points on or close to the bisector represent the best correspondence between the model-simulated data and the lidar ones.
4.1. The TAU model vs. lidar
The distribution of points in the scatter plot reveals that the model results vary between 0.04 1012 and 95.0 1012 cm3cm3, whereas the lidar data are between the lower detection limit of 3.62 1012 and 163.0 1012 cm3cm3. Overall, for the 34 days under consideration, the correlation (r ¼ 0.47) between lidar and model derived data was found, as displayed in Table 1. The correlation is statistically significant within the 0.05 level. In a previous paper (Kishcha et al., 2005), attention was paid to the fact that inaccurate forecasts were associated with cloudiness over the area where the initial 3-D dust distribution had been obtained (with the aid of TOMS indices on the day previous to the forecast). Earth Probe Total Ozone Mapping Spectrometer reflectivity measurements (see http://daac.gsfc.nasa.gov) were used in order to identify cloudy conditions for all points in the above-discussed scatter plots. Averaged reflectivity of less than 20% over the area, where dust was initialized 24 h before the forecast time, was found to correspond mainly to acceptable forecast points. The area, where dust was initialized, is defined by the rectangular area around the starting points of 24-h back trajectories. However, as found in the current study for the TAU model, the forecast errors could be significant even in cloudless conditions. In particular, the correlation for 22 cases with reflectivity less than 20 over the area, where dust was initialized, was rather low (r ¼ 0.44) (Table 1). This is mainly caused by technical problems with TOMS measurements in accordance with NASA announcements (http://daac.gsfc.nasa.gov/data/ dataset/TOMS).
Table 1. Correlation between lidar data and 24-h model-predicted dust volumes, averaged within the dust layer (following Kishcha et al., 2007) Model Four-particle-size DREAM One-particle-size SKIRON One-particle-size TAU
All 34 days
22 days with low cloud presence
0.60 0.49 0.47
0.71 0.54 0.44
Dust Forecast Errors by Using Lidar Measurements Over Rome
49
4.2. SKIRON vs. lidar
The distribution of points in the scatter plot reveals that the model results vary between 0.42 1012 and 211.16 1012 cm3cm3. The SKIRON data correspond a little better to the lidar ones compared with the TAU model results; the correlation (r ¼ 0.49) was found for all 34 days under consideration (Table 1). However, it was surprising that for 22 days with low or without cloud presence over the area, where dust was initialized, the model-lidar correspondence is noticeably better, a higher correlation (r ¼ 0.54) was found. 4.3. DREAM vs. lidar
The distribution of points in the scatter plot indicates that the DREAM data better correspond to the lidar ones compared with other two models. As shown in Table 1, this is supported by higher correlation (r ¼ 0.60) for all 34 days under consideration. It is noticeable that for 22 days with low or without cloud presence over the area, where dust was initialized, the model-lidar correspondence is distinctly better, a higher correlation (r ¼ 0.71) was found. This suggests that non-included dust-radiation and dust–cloud interactions in the modeling system could result in the forecast of lower accuracy in the presence of clouds. In general, the correlation analysis between lidar data and all three models in question gave an indication that multi-particle-size-bin DREAM is always better than other two one-particle models both for all 34 days and also for cloudless conditions. As for the TAU model, its forecast could be less accurate both for all days and for cloudless conditions. Our analysis gave us proof that the accuracy of TOMS measurements is not satisfactory for dust forecasting because of problems connected with inaccurate spectrometer calibration, as announced by NASA. 4.4. Statistical histograms of forecast errors
An analysis of statistical distributions of forecast mean errors allows the clarification of the difference between the three dust prediction systems under investigation. To this end, statistical histograms of 24-h forecast errors for averaged dust volume within the dust layer over Rome were constructed, as shown in Fig. 1. The forecast mean error was defined as the difference between the common logarithm of lidar-derived dust volume and the one simulated by the model. Consequently, positive errors mean underestimating of lidar data by the model, while negative ones
50
P. Kishcha et al.
Figure 1. Statistical distributions of 24-h forecast errors for model-simulated dust volume over Rome (averaged dust volume within the dust layer): (a) for all the 34 days under investigation, (b) for the 22 days with low cloudiness less than 20%, and (c) for the 10 days with cloudiness exceeding 20% over the area where the dust originated (after Kishcha et al., 2007).
mean overestimating. Different histograms are analyzed in Fig. 1: (1) for all the 34 days in question (Fig. 1a), (2) only for the 22 days with low or without cloudiness, and (3) for the 10 days with cloudiness exceeding 20%, as characterized by the averaged TOMS reflectivity (Fig. 1c). The histograms in Fig. 1a reveal the following characteristic features of forecast-error distributions: (a) Maxima of the histograms are close to zero, meaning that, on average, both SKIRON and DREAM produce acceptable forecasts. (b) However, the TAU model errors are spread over a wide range, indicating that the TAU model predictions tend to underestimate lidar data; the errors are mainly positive. (c) The error distribution for the SKIRON model is more symmetric; DREAM more overestimates lidar data.
Dust Forecast Errors by Using Lidar Measurements Over Rome
51
Figure 1b demonstrates that for days with low or without cloud presence, forecast errors are spread over a narrower range. This highlights the fact that the cases without clouds are mainly associated with dust forecasts of higher accuracy. As for the TAU model, forecast errors are spread over a wider range because of inaccurate TOMS data. In contrast, as shown in Fig. 1c for cloudy days, for all models errors are spread over a wider range, pointing to that these cases are frequently associated with dust forecasts of lower accuracy. The TAU model errors shift to positive values (underestimation), while those for DREAM/ SKIRON shift to negative values (overestimation).
5. Conclusions
Our comparative analysis of model capabilities for providing reliable forecasts of dust vertical distribution in the atmosphere highlights the following (Kishcha et al., 2007): The model vs. lidar comparison clearly shows the advantage of using multiple-particle-size representation in dust modeling. The use of fourparticle-size bins in the dust model DREAM (and evidently in the newer four-particle-size version of SKIRON), instead of the use of only one-size bins in the older one-particle-size version of SKIRON, improves dust forecasts. The correlation between model and lidar data for all 34 days under consideration is equal to 0.60 for DREAM against 0.49 for the one-particle-size SKIRON model. This is also supported by the correlation estimates for cloudless conditions. For cases with low or without cloud presence over the area where the dust originated, a higher correlation was found: 0.71 for DREAM and 0.54 for SKIRON. This highlights that cloud presence could contribute to additional dust forecast errors in SKIRON and DREAM. Two possible reasons are suggested: (1) Weather forecast errors in cloud position, amount, and structure could affect the radiation balance over the dust sources. This implies additional errors in dust emission because of its link with the sensible heat flux over dust sources (Perez et al., 2006). In particular, a smaller outgoing sensible turbulent heat flux reduces both dust emission and the turbulent momentum transfer from the atmosphere; (2) non-included dust-radiation and dust–cloud interactions in the modeling systems could result in the forecast of lower accuracy in the presence of clouds. Recently, Perez et al. (2006) introduced the dust-radiative effect into DREAM, outlining its critical influence on the weather and dust forecasts produced by the model.
52
P. Kishcha et al.
The present study, however, has the following limitations: (1) uncertainties in the lidar data, (2) only one lidar station (Rome) was used in the validation of the models, and (3) a limited number of dust episodes were analyzed. For these reasons, the hypotheses aforementioned should be explored in detail, using a larger set of episodes and measurements. As for the pre-2006 TAU model, its forecast errors were mainly caused by the TOMS measurement problems. The TOMS problems took place even in the absence of cloudiness. Therefore, for the TAU model, the forecast errors could be significant even in cloudless conditions. The technical problems with TOMS measurements explain NASA’s decision to replace the calculation of TOMS indices based on the Earth Probe satellite measurements by OMI indices from the AURA Earth Observing System; this was put into practice from January 1, 2006.
Discussion
Ø. Seland: P. Kishcha:
I. Tegen:
P. Kishcha
Are there any changes in the vertical distribution due to precipitation not reaching the ground? A dry and wet dust deposition scheme with a constant washout parameter is included in all three models under discussion. Therefore, the precipitation effects on dust are taken into consideration. However, there is no parameterization considering the case with precipitation not reaching the ground. The speaker identified the difference in size bins as the largest difference between the DREAM and SKIRION models. To which extent could differences in the initialization contribute to differences in the results? Regarding the comparison of modeled dust loads and lidar retrievals of dust volumes, the main differences were found at low dust concentrations. Do the lidar results only show dust concentrations or could other aerosols ‘‘contaminate’’ the lidar retrievals? The discussed models (DREAM, the older one-particle version of SKIRON, and the pre-2006 TAU model) have much in common because of their origin in the same predecessors with various components upgraded afterwards. On the other hand, the main differences between the models are (a) multiple particle representation in DREAM in contrast to others, (b) their
Dust Forecast Errors by Using Lidar Measurements Over Rome
53
approach to dust initialization: DREAM and SKIRON use their previous forecast while the pre-2006 TAU model uses TOMS aerosol indices. The mode –vs. lidar comparison showed that (1) the use of four particle size classes instead of only one improves dust forecast, (2) using TOMS indices for dust initialization could result sometimes in significant forecast errors because of the technical problems with TOMS measurements, as announced by NASA. In particular, at low dust concentrations the forecast errors caused by incorrect TOMS indices were frequently detected. Lidar-derived vertical profiles, used in the quantitative model vs. lidar comparison, related only to mineral dust volume in accordance with the special technique developed by G.P. Gobbi’s group (e.g., Barnaba and Gobbi, 2001). ACKNOWLEDGMENTS
This study was supported by the Israeli Ministry of Environment’s grant, by the Urban air pollution Italian–Israeli joint project, and also by the GLOWA-Jordan River BMBF-MOS project. The authors gratefully acknowledge Boris Starobinets for helpful comments and discussion. REFERENCES Alpert, P., Krichak, S.O., Tsidulko, M., Shafir, H., Joseph, J.H., 2002. A dust prediction system with TOMS initialization. Mon. Weather Rev. 130(9), 2335–2345. Barnaba, F., Gobbi, G.P., 2001. Lidar estimation of tropospheric aerosol extinction, surface area and volume: Maritime and desert-dust cases. J. Geophys. Res. 106(D3), 3005–3018. (Correction: J. Geophys. Res., 10.1029/2002 JD002340, 2002). Ginoux, P., Chin, M., Tegen, I., Prospero, J.M., Holben, B., Dubovik, O., Lin, S.-J., 2001. Sources and distributions of dust aerosols simulated with the GOCART model. J. Geophys. Res. 106, 20255–20274. Gobbi, G.P., Barnaba, F., Ammannato, L., 2004. The vertical distribution of aerosols, Saharan dust and clouds at Rome (Italy) in the year 2001. Atmos. Chem. Phys. 3, 2161–2172. Gobbi, G.P., Barnaba, F., Blumthaler, M., Labow, G., Herman, J., 2002. Observed effects of particles non-sphericity on the retrieval of marine and desert-dust aerosol optical depth by lidar. Atmos. Res. 61, 1–14. Gobbi, G.P., Barnaba, F., Van Dingenen, R., Putaud, M., Mircea, M., Facchini, M.C., 2003. Lidar and in situ observations of continental and Saharan aerosol: Closure analysis of particles optical and physical properties. Atmos. Chem. Phys. 3, 2161–2172.
54
P. Kishcha et al.
Janjic, Z.I., 1994. The step-mountain Eta coordinate model: Further developments of the convection, viscous sublayer and turbulence closure schemes. Mon. Weather Rev. 122, 927–945. Kallos, G., Katsafados, P., Papadopoulos, A., Nickovic, S., 2006. Transatlantic Saharan dust transport: Model simulation and result. J. Geophys. Res. 111, D09204, doi:10.1029/2005JD006207. Kallos, G., Nickovic, S., Papadopoulos, A., Jovic, D., Kakaliagou, O., Misirlis, N., Boukas, L., Mimikou, N., Sakellaridis, G., Papageorgiou, J., Anadranistakis, E., Manousakis, M., 1997. The regional weather forecasting system SKIRON: An overview. Paper presented at the International Symposium on Regional Weather Prediction on Parallel Computer Environment, University of Athens, Athens, Greece, 15–17 October 1997. Kinne, S., Lohmann, U., Ghan, S., Easter, R., Chin, M., Ginoux, P., Takemura, T., Tegen, I., Koch, D., Herzog, M., Penner, J., Pitari, G., Holben, B., Eck, T., Smirnov, A., Dubovik, O., Slutsker, I., Tanre, D., Torres, O., Mishchenko, M., Geogdzhayev, I., 2003. Monthly averages of aerosol properties: A global comparison among models, satellite data and AERONET ground data. J. Geophys. Res. 108(D20), 4634, doi:10.1029/2001JD002011. Kishcha, P., Alpert, P., Shtivelman, A., Krichak, S.O., Joseph, J.H., Kallos, G., Katsafados, P., Spyrou, C., Gobbi, G.P., Barnaba, F., Nickovic, S., Perez, C., Baldasano, J.M., 2007. Forecast errors in dust vertical distributions over Rome (Italy): Multiple particle size representation and cloud contributions. J. Geophys. Res. in press. Kishcha, P., Barnaba, F., Gobbi, G.P., Alpert, P., Shtivelman, A., Krichak, S.O., Joseph, J.H., 2005. Vertical distribution of Saharan dust over Rome (Italy): Comparison between 3-year model predictions and lidar soundings. J. Geophys. Res. 110, D06208, doi:10.1029/2004JD005480. Mesinger, E., 1997. Dynamics of limited area models: Formulation and numerical methods. Meteor. Atmos. Phys. 63, 3–14. Nickovic, S., Dobricic, S., 1996. A model for long-range transport of desert dust. Mon. Weather Rev. 124, 2537–2544. Nickovic, S., Kallos, G., Kakaliagou, O., Jovic, D., 1997. Aerosol production/transport/ deposition processes in the Eta model: Desert cycle simulations. Preprints. Proc. Symp. on Regional Weather Prediction on Parallel Computer Environments, University of Athens, Athens, Greece, pp. 137–145. Nickovic, S., Kallos, G., Papadopoulos, A., Kakaliagou, O., 2001. A model for prediction of desert dust cycle in the atmosphere. J. Geophys. Res. 106, 18113–18129. Papadopoulos, A., Kallos, G., Nickovic, S., Jovic, D., Dacic, M., Katsafados, P., 1997. Sensitivity studies of the surface and radiation parameterization schemes of the SKIRON system, In: Kallos, G., Kotroni, V., Lagouvardos, K. (Eds.), Proceedings of Symposium on Regional Weather prediction on Parallel Computer Environments. The University of Athens, Greece, pp. 155–164. ISBN: 960-8468-22-1. Perez, C., Nickovic, S., Pajanovic, G., Baldasano, J.M., Ozsoy, E., 2006. Interactive dustradiation modeling: A step to improve weather forecasts. J. Geophys. Res. 111(D16206), doi:10.1029/2005JD006717. Shao, Y., Raupach, M.R., Findlater, P.A., 1993. Effects of saltation bombardment on the entrainment of dust by wind. J. Geophys. Res. 98, 12719–12726.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06016-0
55
Chapter 1.6 Modelling urban heat island in the context of a Mediterranean city F. Santese, S. Di Sabatino, E. Solazzo and R. Britter Abstract Urban heat island (UHI) is one of the most well known forms of localised anthropogenic climate modification. It causes a local alteration of atmospheric stability. According to a top-down methodology, mesoscale meteorological modelling is a commonly used approach to study the impact of UHI on atmospheric stability at the urban scale. Our work is an effort to investigate UHI using a bottom-up approach by looking at the UHI through a computational fluid dynamics (CFD) model applied to the street canyons of a neighbourhood area. The CFD code is set up to model the thermal response (structure surface temperature and ambient air temperature) of an urban system to the outside climate. The determination of the air temperature in an urban unit allows the calculation of the DTur factor representing the difference between the air temperature in the urban system (u) and the air temperature recorded at the closest meteorological station (r), generally situated in the countryside. This factor, introduced by Oke in Boundary Layer Climate, (1987), enables the analysis of the heat island generated by an urban system. The simulation results obtained from the CFD model allows the estimation of the DTur factor in relation to physical aspects and geometrical configurations. We apply this technique to study UHI of a Mediterranean city of which some urban temperature measurements and morphometry from a digital elevation model (DEM) are available. 1. Introduction
The urban heat island (UHI) effect is the result of many complex processes and although it has been well described in many experimental and
56
F. Santese et al.
numerical works, simple prediction methods are still required. In particular, it is of interest to estimate UHI intensity within an urban area as a function of time, weather conditions and building characteristics and for practical applications such as road climatology, phenology, energy conservation and weather forecasting. In the last 30 years, much research has been devoted to the study of UHI both to understand if and how it influences mesoscale circulation and how it impacts on human life. Following Oke’s original framework in which there is a distinction between UHI in the urban boundary layer (UBL) and UHI in the urban canopy layer (UCL), it has been clarified that within an urban area, many UHIs exist, each with their own characteristics controlled by different combinations of energy exchange processes. However, both definitions have historically in common the fact that they have an air temperature excess over rural environs. In other words an urban heat island develops when rural cooling rates are greater than the urban ones (Oke and Maxwell, 1975). The major challenge still remains in the modelling of such phenomena. Many numerical studies based on mesoscale modelling are available (Murakami et al., 1997; Ichinose et al., 1999; Martilli et al., 2002). Conversely, at the street scale the so-called urban canyon models (Kondo and Liu, 1998) allow the estimation of the UHI from a local energy balance. Many studies deal with the influence of building geometry on the flow, using field and wind tunnel experiments, numerical and theoretical models (Sini et al., 1996; Bentham and Britter, 2003; Kastner-Klein and Rotach, 2004). There are few studies dealing with thermal aspects of the urban environment and the influence of the temperature distribution on the urban climatology is not well understood yet. The study of the transfer of scalars requires a separate study and analysis from what we know about the momentum exchange (Barlow et al., 2004). This work represents our first step towards the characterisation of UHIs-type in a Mediterranean medium-size city. We use a bottom-up approach by analysing the influence of building configurations at the urban scale on both the flow and temperature distributions through computational fluid dynamics (CFD) simulations in a neighbourhood zone where temperature measurement campaigns are currently being ongoing. Before proceeding with the real simulation and using the CFD code as an instrument for investigating temperature patterns at the neighbourhood area, we have validated the CFD model against wind tunnel experiments (Uehara et al., 2000). In the experimental work, thermal stratification is created by controlling wind temperature and wind tunnel floor temperature. We compare experimental measurements of wind speed and temperature profile with our computational results.
Modelling Urban Heat Island in the Context of a Mediterranean City
57
2. Fluent modelling set up for all simulations
The computational study was made using Fluent, a finite-volume based commercial code (Fluent, Inc., 2003). A standard steady case k–e turbulence model was used for all simulations. At the inlet the profiles for wind velocity U(z), turbulent kinetic energy k(z) and turbulent dissipation rate e(z) were provided by the following formulas: u zd u2 z u3 z 1 ; ðzÞ ¼ 1 (1) ; kðzÞ ¼ ð1=2Þ UðzÞ ¼ ln k kz z0 d d Cm where d is the height of the boundary layer, z0 is the roughness length, d is the zero-plane displacement length; u is the friction velocity, Cm( ¼ 0.09) and k( ¼ 0.40) are constants. Boussinesq approximation and the thermal expansion coefficient were set out. The CFD code is set up to model the thermal response (building surface temperature and ambient air temperature) of an urban system to the outside climate using a similar set up as in Solazzo et al., 2005. 2.1. Wind tunnel simulation runs
For the validation of our simulations on an array of buildings, wind tunnel experiments from Uehara et al. (2000) were used. Those experiments were conducted using a model that represented city streets with simple shaped block forms, while varying atmospheric stability across seven stages from stable (bulk Richardson number—Rb ¼ 0.79) to unstable (Rb ¼ 0.21). The Richardson number that defines atmospheric stability (Snyder, 1972; U.S. Environmental Protection Agency, 1981; Cermak, 1984) is given by Rb ¼ gHðT H T 0 Þ=ðU 2H TÞ; where g is the acceleration due to gravity, H the building height, TH the temperature at the top of the street canyon, T0 the temperature of the ground, UH the mean wind speed at the top of the canyon and T the mean temperature. The wind speed range in the wind tunnel was between 0.2 and 10 m s1. For our computational runs, we used a tetrahedric unstructured mesh, with the smaller cell size equal to 15 mm and an expansion rate of 1.25. This resulted in a computational domain of about 714,000 computational cells. All parameters were set as suggested in Uehara et al. (2000) for the approaching flow that is the boundary layer height d ¼ 0.7 m; the roughness length z0 ¼ 3.3 103 m, the displacement height d ¼ 35 103 m. UrefU700 ¼ 1.5 m s1, the friction velocity u is given by u/Uref.. Figure 1 shows the geometry configuration reproducing blocks arrangement in the wind tunnel. The dimensions of the computational domain are
F. Santese et al.
58
Figure 1. Computational domain size and geometry configuration of CFD simulations used for comparison with measurements from a wind tunnel experiment. Table 1. Temperature and Rb set-up values in the wind tunnel and in the CFD model Rb Ta (K) Tf (K)
0.79 351 294
0.43 331 294
0.11 311 294
0 293 293
0.12 292 313
0.19 292 332
0.21 293 352
6 m along X-axis, 1.5 m along Y-axis and 1 m along Z-axis. Each block is 100 mm by 100 mm by 100 mm; all elements are spaced 100 mm apart in X direction and 50 mm in Y direction giving an aspect ratio of 1:1. The distance between the inlet surface and the first row of blocks was set to be equal to 5H, where H is the height of the element block, while the distance between the last row of elements and the output surface is set to be equal to 20H; the distance between the elements and the right-hand side symmetry is equal to 5H. Figure 1 also shows the measurement axis along which we calculated velocity and temperature profiles. In the wind tunnel it indicates the position where measurements were made that is between the fifth and sixth rows of building, 1 m leeward from the leading edge of city blocks. We set symmetry condition at the top of the domain and at the two sides, an outflow condition at the downstream edge of the domain, and a no-slip condition at the side facets, street and roof of the buildings. The temperature distribution was set at the inlet zone (wind temperature, Ta) and at the bottom (Tf) of our domain, following the indication from the wind tunnel setting for thermal stratification and fixing temperature as thermal boundary condition. According to wind tunnel experimental readings, we set our computational runs with multiple sets of temperature for both the flow and the floor. Table 1 reports temperatures with related Rb used in the wind tunnel and in our CFD simulations.
Modelling Urban Heat Island in the Context of a Mediterranean City
59
2.2. Simulation runs on DEM
Geometry configuration for the real case is available through a digital elevation model (DEM) (Chirizzi, 2004) of a neighbourhood zone of Lecce, a Mediterranean city in southern Italy (Fig. 2). City zone occupies an area of 210 m by 230 m and the chosen 3D computational domain has dimensions of 960 m by 310 m by 300 m. The black line in Fig. 2 indicates the only street canyon within the area where we imposed a temperature difference between the walls and the flow. We chose to heat the building facets in the east direction (negative Y-axis), in order to simulate eastward solar radiation (particular of heated facets in Fig. 3). We created an unstructured mesh with over 1,700,000 cells with a minimum volume cell equal to 5.5 102 m3. Morphological parameters were calculated according to methodology developed by Ratti et al. (2002) which gave: z0 ¼ 0.1 m, u ¼ 0.446 m s1, d ¼ 10.1 m, d ¼ 200 m. 2.2.1. Boundary condition
North wind direction was chosen for our runs (along X-axis in Fig. 2). We set air temperature (in inlet) at 303 K (this value was derived by
Figure 2. Geometry of the neighbourhood city area used in the CFD modelling.
60
F. Santese et al.
Figure 3. Details of the city geometry showing the heated facets of buildings in the eastward side.
several measurements taken during summer 2005, in situ); temperature of heated facets was initially set to 305 K and 313 K in subsequent runs.
3. Results and discussion 3.1. Evaluation of computational results against wind tunnel data
In Fig. 4 wind profiles calculated with Fluent are compared against wind tunnel profiles. Both profiles are similar, qualitatively speaking but we observe that when zoH for all case that is the stable case (Rb ¼ 0.79), neutral case (Rb ¼ 0) and unstable case (Rb ¼ 0.21) simulated wind speeds are greater than the measured ones. However, above the buildings top, simulated wind speeds are lower than wind tunnel measurements for the first two cases; conversely, for the unstable case (and for intermediate others), calculated values are slightly larger than the measured ones. In general, we can say that wind speed in and above the street canyon, U/ U700, diminishes as the stratification strengthened (it drops almost to zero), but wind speed increases as instability increases (inside the street canyon the reverse flow is strong because of the instability). With Fluent results the effect of reverse flow is less evident. A possible explanation for this to happen is that the vortex that forms in the street canyon becomes weaker when the atmosphere is stable, and stronger when the atmosphere is unstable. On the other hand, we may expect that when atmosphere is unstable mixing processes in the street canyon cause the vertical temperature gradient to grow smaller (see Fig. 5), and thus the instability to decrease.
Modelling Urban Heat Island in the Context of a Mediterranean City
61
Figure 4. Comparison of the experimental and modelled non-dimensional wind profiles (u/ Uref) as a function of the non-dimensional height for different Rb values.
Figure 5. Comparison of the experimental and modelled non-dimensional temperature profiles (TTf)/(TaTf) as a function of the non-dimensional height for different Rb values.
62
F. Santese et al.
Figure 6. Modelled temperature profiles at different distances from the heated wall.
3.2. Evaluation of DEM simulation
In Fig. 6 modelled temperature profiles for different distances from wall are shown. The first plot refers to simulation with DT ¼ |TwallTair| ¼ 2 K, the second one to DT ¼ 10 K. It is evident that there is a temperature gradient only for positions near the heated facet (at 1 m from this one). At the centre of street canyon temperature profile seems to be uniform, as a strong mixing is taking place. Calculated wind profiles appear to be unaffected by the imposition of different temperatures on the wall. 4. Conclusion
Results of the comparison of computational CFD simulations of urban street canyons with heated walls and wind tunnel data show a good agreement in terms of qualitative behaviour of temperature profiles. Results of CFD simulations of a real neighbourhood area where a street canyon was partially heated confirm that vortex circulation and mixing tend to uniform temperature distribution, even in the case of asymmetric thermal boundary condition. Temperature patterns and their possible role in flow modification will be also investigated by addressing the study of the effect of UHI on urban stability by a top-down approach and by looking at the relationship between the heated surface and exchange processes at the top of street canyons. REFERENCES Barlow, J.F., Harman, I.N., Belcher, S.E., 2004. Scalar fluxes from urban street canyon. Part I: Laboratory simulation. Bound. Layer Meteorol. 113, 369–385.
Modelling Urban Heat Island in the Context of a Mediterranean City
63
Bentham, T., Britter, R., 2003. Spatially averaged flow within obstacle arrays. Atmos. Environ. 37, 2037–2043. Cermak, J.E., 1984. Physical modelling of flow and dispersion over complex terrain. Bound. Layer Meteorol. 30, 261–292. Chirizzi, C., 2004. Realizzazione ed analisi di Modelli Digitali di Elevazione (DEM), Tesi di Laurea, A.A.2003–2004, Universita` degli Studi di Lecce. Fluent Inc., 2003. FLUENT 6.2 user’s manual. http://www.fluent.com Ichinose, T., Shimodozono, K., Hanaki, K., 1999. Measurement of thermal environment in Kyoto city and its prediction by CFD simulation. Atmos. Environ. 33, 3897–3909. Kastner-Klein, P., Rotach, M.W., 2004. Mean flow and turbulence characteristics in an urban roughness sublayer. Bound. Layer Meteorol. 111, 55–84. Kondo, H., Liu, F., 1998. Study on the urban thermal environment obtained through onedimensional urban canopy model. J. Jpn. Soc. Atmos. Environ. 33(3), 179–192. Martilli, A., Clappier, A., Rotach, M.W., 2002. An urban surface exchange parameterisation for mesoscale models. Bound. Layer Meteorol. 104, 261–304. Murakami, S., Mochida, A., Kim, S., Ooka, R., 1997. Influence of land-use conditions on velocity and temperature fields over Kanto Plane. Trans. AIJ 491, 31–39. Oke, T.R., Maxwell, G.B., 1975. Urban heat island dynamics in Montreal and Vancouver. Atmos. Environ. 9, 191–200. Ratti, C., Di Sabatino, S., Caton, F., Britter, R., Brown, M., Burian, S., 2002. Analysis of 3-D urban databases with respect to pollution dispersion for a number of European and American cities. Water, Air and Soil Pollution: Focus 2, 459–469. Sini, J.-F., Anquetin, S., Mestayer, P.G., 1996. Pollutant dispersion and thermal effects in urban street canyons. Atmos. Environ. 30, 2659–2677. Snyder, W.H., 1972. Similarity criteria for the application of fluid models to the study of air pollution meteorology. Bound. Layer Meteorol. 3, 113–134. Solazzo, E., Di Sabatino, S., Britter, R., 2005. Transfer processes in a simulated urban street canyon using morphological parameters from DEM analysis. Proceedings of the 5th International Conference on Urban Air Quality, Valencia 29–31 March 2005. Uehara, K., Murakami, S., Oikawa, S., Wakamatsu, S., 2000. Wind tunnel experiments on how thermal stratification affects flow in and above urban street canyons. Atmos. Environ. 34, 1553–1562. U.S. Environmental Protection Agency, 1981. Guidelines for fluid modeling of atmospheric diffusion, EPA-600/8-81-009, EPA, Office of Air Quality Planning and Standards, Research Triangle Park, North Carolina.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06017-2
64
Chapter 1.7 Evaluation of land surface scheme modifications on atmospheric transport and deposition patterns in Copenhagen metropolitan area Alexander Mahura, Alexander Baklanov, Steen Hoe, Jens H. Sorensen, Claus Petersen and Kai Sattler Abstract The spatial and temporal variability of the concentration and deposition fields simulated by the Local Scale Model Chain (LSMC) of ARGOS system (resulted from hypothetical accidental releases occurred in the metropolitan area of Copenhagen, Denmark) are evaluated. For that, the HIgh Resolution Limited Area Model (HIRLAM) is used to simulate meteorological fields taking into account urban-related modifications of the land surface scheme. In this study, several specific dates—typical, low, and high winds and high precipitation—are studied in details. 1. Introduction
The generated output of the Numerical Weather Prediction (NWP) models serves as an input in many applications, and especially in those related to atmospheric pollution tasks. In particular, the 3D meteorological fields are used to simulate atmospheric transport, dispersion, and deposition of short- and/or long-term releases of harmful matter. Although the resolution of current operational NWP models has increased up to almost 1 km resolution, the urban areas are still poorly resolved in models and especially in parameterizations for the surface and boundary layers. The EU-project entitled ‘‘Integrated Systems for Forecasting Urban Meteorology, Air Pollution and Population Exposure, FUMAPEX’’ (http:// fumapex.dmi.dk) suggested several approaches for urbanization of NWP models (Baklanov et al., 2005a, b). These (all having different computational requirements and time) included modifications of the effective roughness and urban heat fluxes approach (Baklanov et al., 2005a, b), the
Land Surface Scheme Modifications in Copenhagen
65
building effect parameterization urban sub-layer module (Martilli et al., 2002), and the soil model for submeso scales urbanized version (Dupont et al., 2004; Otte et al., 2004). In this paper, following example of Baklanov et al. (2007), the first mentioned inexpensive way of urbanization of NWP model, based on modifications of the ISBA scheme, was used. The diurnal variations of wind and temperature, fluxes fields in the low surface layer produced by the DMI HIgh Resolution Limited Area Model (HIRLAM) model were evaluated taking into account modifications done in the Interaction Soil– Biosphere–Atmosphere (ISBA) scheme with respect to urban roughness and anthropogenic heat flux (AHF). The variability in spatial distribution of concentration and deposition patterns produced by the Local Scale Chain Model of the ARGOS system was analyzed. Combined impacts were estimated for the Copenhagen (CPH) metropolitan area of Denmark and surroundings.
2. Methods 2.1. Meteorological modelling
The present DMI weather forecasting system (Sass et al., 2002) performs daily forecasts of meteorological fields employing the HIRLAM model (Unden et al., 2002) consisted of two nested models called DMIHIRLAM-S05 and -T15. Both models are identical, except for horizontal resolution (5 vs. 15 km) and boundaries of domains. The lateral boundary values for T15 (modelled every 6 h) are from the ECMWF model. The current operational DMI-model is semi-implicit, with semi-Lagrangian advection and leapfrog time stepping (with the semi-Lagrangian advection as optional). Physics such as short- and long-wave radiation, turbulence (except gravity wave drag), deep and shallow convection, cloud and precipitation generation, and air–sea/air–land interactions are parameterized and included. The operational model applies an implicit digital filter initialization technique in order to remove the large amplitude gravity wave oscillations in the first few hours of forecast. There are also several experimental research DMI-HIRLAM models with a high resolution of 1.4 km. Currently, these are run for limited periods for selected territories mostly with a focus on the CPH metropolitan area. The main assumptions in these models are identical to the operational versions, and boundary conditions are taken from T15 and S05. Modifications for the urban effects, considered in the following section, were included into high-resolution runs.
66
Alexander Mahura et al.
2.2. Land use classification and urban features
The land use classification for the current version of DMI-HIRLAM is based on several datasets including high-resolution CORINE dataset. In HIRLAM some fields, such as roughness, albedo, vegetation type, orography, etc., are assumed to be constant in modelling domains during operational runs. These fields are once produced and stored in the climate generation files and are available for analyses and forecasts. The reclassification of datasets into 20 major classes is performed following Sattler (2000). Then, it is reduced (based on the dominating and secondary class approach) into five major tiles of the ISBA land surface scheme (Navascue´s et al., 2003; Rodrı´ guez et al., 2003) in HIRLAM represented by water, ice, low vegetation, forest, and no vegetation. The characteristics (such as monthly leaf area index, albedo, roughness, etc.) of dominating types (from 20 classes) are used further in the ISBA calculation. In the scheme, the urban class was treated with characteristics of bare soils modified with accordance of urbanized features. 2.3. Pollution modelling
In our study, the ARGOS system (Hoe et al., 2002) with the Local Scale Model Chain (LSMC) (Mikkelsen et al., 1997) was employed to simulate atmospheric transport, dispersion, and deposition resulting from hypothetical accidental releases of radioactive matter from a selected location. It consists of the atmospheric dispersion model called RIso Mesoscale PUFF (RIMPUFF) model (Mikkelsen et al., 1984). It is consisted of plume rise, inversion, ground level reflection, and gamma dose formulations and algorithms. The model output includes the surface level air concentration, deposition, and gamma dose rates. As input, the 3D meteorological fields produced by the DMIHIRLAM-U01 model were used. For all selected dates, the release point is located in the CPH metropolitan area, the duration of release is equal to 12 h (i.e., starting at 03 UTC and ending at 15 UTC), the radionuclide considered is 137Cs, and the emission rate is equal to 1011 Bq s 1. 3. Results and discussion
Based on long-term runs of the DMI-HIRLAM high-resolution model during summer of 2005, several specific dates were selected using the wind velocity and direction from the surface and radiosounding observations as criteria. These dates have represented typical winds (18 Jun), low winds
Land Surface Scheme Modifications in Copenhagen
67
(19 Jun), high winds (4 Jun), and high precipitation (30 Jul) conditions for atmospheric transport over the Island of Zeeland, Denmark where CPH is situated. In these runs in the ISBA scheme, the roughness for cells (where the urban class was represented in the modelling domain) was increased up to 2 m; and second, the contribution of AHF up to 200 W m 2 was incorporated into the scheme. The generated meteorological output was further used to simulate atmospheric transport, dispersion, and deposition of pollution over the metropolitan area. In this paper, the diurnal cycle (i.e., 00 UTC+24-h forecast) variability of meteorological and pollution (concentration and deposition) output fields were analyzed for mentioned dates. The meteorological fields’ simulations for the urbanized areas were driven using boundary conditions of the DMI-HIRLAM-S05 model. These conditions were used as input for simulation of meteorological fields for the DMI-HIRLAM research version with resolution of 1.4 km, which includes the CPH and Malmo¨ metropolitan areas and surroundings. The diurnal cycle of meteorological variables such as wind velocity (at 10 m) and temperature (at 2 m) as well as concentration and deposition patterns were analyzed comparing outputs of the control run vs. runs with modified parameters for urban class. At each UTC term, the 2D (values in latitude vs. longitude gridded domain) difference fields for mentioned variables were produced/analyzed by subtracting outputs from the control run without any changes made vs. run with changes made for roughness and AHF. It was found, that for the low wind conditions (LWC) date, the modified run showed increase in temperature at 2 m over the urban areas. This increase was more than 11C during 18–06 UTC (with a maximum of 1.61C at 04–05 UTC), and it was less than 0.91C during 07–17 (with a minimum of 0.51C at 16–17 UTC). On average, decrease in wind velocity at 10 m was around 2 m s 1 during nighttime, and it was around 1.5 m s 1 during daytime, with a maximum of up to 5 m s 1. An example is shown in Fig. 1. For the typical wind conditions (TWC) date, the urbanized run also showed an increase in temperature at 2 m, but this increase was substantially lower than for LWC, i.e., on average, during 06–17 UTC it was less than 0.31C over most parts of the urbanized areas. During 18–05 UTC, it was within a range of 0.4–0.71C with a maximum of 1.11C at 20 UTC. On average, the decrease in wind velocity at 10 m was around 1.7 m s 1 during nighttime, and it varied 1–2 m s 1 during daytime, with a maximum of up to 4 m s 1. For the high wind conditions (HWC) date, during all terms the temperature increase over the urbanized areas was always less than 0.21C
68
Alexander Mahura et al.
Figure 1. Difference plots (between outputs of the DMI-HIRLAM-U01 control vs. urbanized runs) for temperature at 2 m (top) and for wind velocity at 10 m (bottom) at 03 UTC forecast on 19 May 2005.
Land Surface Scheme Modifications in Copenhagen
69
(with a maximum of 0.81C at 04 UTC). On average, the decrease in wind velocity at 10 m was less than 0.5 m s 1 during evening hours and nighttime, and it became slightly larger after 10 UTC reaching a maximum of 1.6 m s 1 at 15 UTC. For the high precipitation conditions (HPC) date, the synoptic situation had been characterized by a relatively continuous precipitation pattern during daytime. The temperature differences over the urban areas varied 0.2–11C. A clear pattern on a diurnal cycle was not identified because it was also significantly affected by the frontal passage. The same situation was characteristic for wind at 10 m (with an observed maximum of 1.5 m s 1). Only for the LWC date, the differences in concentration and deposition patterns were significant as shown in Fig. 2. As seen it has been characterized by a wider spreading of the contaminated cloud over the urbanized area and surroundings, and hence, affecting a larger group of population. For the TWC and HWC dates, there are no significant differences between the control vs. urban runs, due to smaller changes in meteorological variables’ values on a scale of diurnal cycle (as described above) as well as smaller sizes of urbanized areas affected by these changes. For the HPC date, the situation is more complex for analysis due to substantial removal of pollution from the contaminated cloud at the initial stages of emissions into the atmosphere.
4. Conclusion
In this study, we evaluated diurnal variability of meteorological and pollution patterns based on changes (as a function of roughness and AHF) in the ISBA land surface scheme. The four specific—low, high, and typical winds, and high precipitation—cases/dates during summer of 2005 were analyzed. It was found that changes in roughness and AHF modify the structure of the surface layer wind and temperature fields over urban areas. On average, the decrease in wind velocity is the highest (1.5 m s 1) for LWC, and it is the lowest (less than 0.5 m s 1) for HWC. Similarly, the average increase in temperature is the highest (more than 0.51C) for LWC, and it is the lowest (less than 0.31C) for HWC and HPC. The significant differences in concentration and deposition patterns were observed for LWC. For TWC and HWC, there are no large differences in spatial and temporal structure of pollution-related patterns. For HPC, this impact was not observed due to substantial removal of pollution at the initial stages.
70
Alexander Mahura et al.
Figure 2. Total deposition patterns of 137Cs at 17 UTC forecast on 19 May 2005 for the DMI-HIRLAM-U01 control (top) vs. urbanized (bottom) runs resulting from hypothetical accidental release.
Land Surface Scheme Modifications in Copenhagen
71
Discussion
E. Batchvarova: In the 1.4 km grid resolution of HIRLAM, do you assign the dominant class of land use to the grid cell or do you combine/average between several classes? A. Mahura: For this resolution, in the ISBA land surface scheme of HIRLAM model, the first dominating class was assigned for each grid cell. In these urban grid cells situated over the Copenhagen metropolitan area, the urban class was treated with characteristics similar to the bare soils’ tail of the scheme. E. Genikhovich: In your talk you presented results from sensitivity studies rather than a validation of the model. Do you have results of a validation against field measurement data on scales corresponding to the accidental release of atmospheric pollutants from a point source? A. Mahura: To simulate atmospheric transport, dispersion, and deposition of caesium resulted from hypothetical accidental releases in the Copenhagen metropolitan area, the dispersion RIMPUFF model was employed. It is a part of the ARGOS system. This model, at least, was verified vs. the Chernobyl, ETEX, and Algeciras data and it showed a relatively good performance of the model on local and mesoscales.
ACKNOWLEDGMENTS
Thanks to the DMI Computer Support and HIRLAM group for the collaboration. Financial support of this study came from EU FUMAPEX (EVK4-CT-2002-00097) and HIRLAM international projects. REFERENCES Baklanov, A., Ha¨nninen, O., Slørdal, L.H., Kukkonen, J., Bjergene, N., Fay, B., Finardi, S., Hoe, S.C., Jantunen, M., Karppinen, A., Rasmussen, A., Skouloudis, A., Sokhi, R.S., Sørensen, J.H., Ødegaard, V., 2007. Integrated systems for forecasting urban meteorology, air pollution and population exposure. Atmos. Chem. Phys. 7, 855–874. Baklanov, A., Mahura, A., Nielsen, N.W., Petersen, C., 2005a. Approaches for urbanization of DMI-HIRLAM NWP model. HIRLAM Newslett. 49, 61–75. Baklanov, A., Mestayer, P., Clappier, A., Zilitinkevich, S., Joffre, S., Mahura, A., Nielsen, N.W., 2005b. On the parameterisation of the urban atmospheric sublayer in meteorological models. Atmos. Chem. Phys. Discuss. 5, 12119–12176.
72
Alexander Mahura et al.
Dupont, S., Otte, T.L., Ching, J., 2004. Simulation of meteorological fields within and above urban and rural canopies with a mesoscale model (MM5). Boundary-Layer Meteorol. 113, 111–158. Dupont, S., Mestayer, P., Guilloteau, E., Berthier, E., Andrieu, H., 2005. Parameterization of the urban water budget with the submesoscale soil model. J. Appl. Meteorol. and Climatol. 45(4), 624–648. Hoe, S.C., Muller, A., Gering, F., Thykier-Nielsen, S., Sorensen, J.H., 2002. ARGOS Decision Support System for Nuclear Emergencies. In: Proceeding of the Radiation Protection and Shielding Division Topical Meeting, 14–17 April 2002, Santa Fe, New Mexico, USA. Martilli, A., Clappier, A., Rotach, M., 2002. An urban surface exchange parameterisation for mesoscale models. Boundary Layer Meteorology 104, 261–304. Mikkelsen, T., Larsen, S., Thykier-Nielsen, S., 1984. Description of the Riso puff diffusion model. Nucl. Technol. 67, 56–65. Mikkelsen, T., Thykier-Nielsen, S., Astrup, P., Santabarbara, J., Sorensen, J., Rasmussen, A., Robertson, L., Ullerstig, A., Deme, S., Martens, R., Bartiz, J., Pasler-Sauer, J., 1997. MET-RODOS: A comprehensive atmospheric dispersion module. Radiat. Prot. Dosim. 73, 45–56. Navascue´s, B., Rodrı´ guez, E., Ayuso, J.J., Ja¨rvenoja, S., 2003. Analysis of surface variables and parameterization of surface processes in HIRLAM. Part II: Seasonal assimilation experiment, Norrko¨ping. HIRLAM Techn. Rep. 59, 38. Otte, T.L., Lacser, A., Dupont, S., Ching, J., 2004. Implementation of an urban canopy parameterization in a mesoscale meteorological model. J. Applied Meteorol. 43, 1648–1665. Rodrı´ guez, E., Navascue´s, B., Ayuso, J.J., Ja¨rvenoja, S., 2003. Analysis of surface variables and parameterization of surface processes in HIRLAM. Part I: Approach and verification by parallel runs, Norrko¨ping. HIRLAM Tech. Rep. 58, 52. Sass, B., Nielsen, N.W., Jørgensen, J.U., Amstrup, B., Kmit, M., Mogensen, K.S., 2002. The operational DMI-HIRLAM system—2002-version. DMI Tech. Rep. 02-05, 60. Sattler, K., 2000. New high resolution physiographic data and climate generation in the HIRLAM forecasting system at DMI, an overview. HIRLAM Newslett. 33, 96–100. Unden, P., Rontu, L., Ja¨rvinen, H., Lynch, P., Calvo, J., Cats, G., Cuhart, J., Eerola, K., et al. 2002. HIRLAM-5 scientific documentation. December 2002, HIRLAM-5 Project Report, SMHI.
Regional and intercontinental modelling Chairpersons: Carlos Borrego Douw Steyn Sven-Erik Gryning Nadine Chaumerliac Adolf Ebel Rapporteurs: Joana Valente Bernd Heinold Oswald Knoth Maya Milliez Ralf Wolke
This page intentionally left blank
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06021-4
75
Chapter 2.1 Modeling of secondary aerosols in Switzerland in summer 2003 S. Andreani-Aksoyoglu, J. Keller, A.S.H. Prevot, U. Baltensperger and J. Flemming Abstract The formation and transport of secondary aerosols during a 4-day period in summer 2003 were studied using the three-dimensional air quality model CAMx (Comprehensive Air quality Model with eXtensions) and meteorological model MM5 over an area covering Switzerland and part of the surrounding countries. The modeled components are particulate sulfate, nitrate, ammonium, and secondary organic aerosols (SOA) with a particle diameter smaller than 2.5 mm. Higher concentrations are predicted in southern Switzerland and northern Italy. Differences between the regions in the north and the south of the Alps are discussed with respect to the aerosol concentrations and to the sensitivity of aerosol formation. Sensitivity tests using reduced NH3 and NOx emissions suggest that in northern Switzerland secondary aerosol formation is unlikely to be limited by NH3 but rather by HNO3. On the other hand, aerosol formation around Milan seems to be similarly dependent on HNO3 and NH3 most of the time. However, there are times when limitation by NH3 is stronger. The contribution of biogenic sources to SOA was predicted to be rather high, about 70% in the north, matching the measurements whereas it was lower in southern Switzerland (40%). In northern Italy, anthropogenic sources contribute much more to SOA formation. 1. Introduction
Atmospheric aerosols play an important role in climate change by modifying the radiative balance of the atmosphere (IPCC, 2001) and they are also known to have adverse health effects. The legal threshold for the yearly average for PM10 (particles smaller than 10 mm in aerodynamic diameter d) is 20 mg m 3 in Switzerland. As a short-term threshold, the
76
S. Andreani-Aksoyoglu et al.
concentration averaged over 24 h may exceed 50 mg m 3 only once a year. PM10 concentrations in Switzerland frequently exceed the threshold values, especially in the south of the Alps. While the formation of gaseous pollutants such as ozone is well known, there is still a lack of knowledge about aerosol formation. Gehrig and Buchmann (2003) evaluated the long-term PM2.5 and PM10 measurements at various Swiss sites. The chemical composition of atmospheric PM was investigated by Hueglin et al. (2005). Understanding the partitioning behavior of semivolatile species between the gas and aerosol phases can help us predict how changes in anthropogenic and biogenic activity will influence the formation of aerosols in the atmosphere. In recent years, several air quality models have been upgraded to include aerosol dynamical processes (Schell et al., 2001; Hass et al., 2003; Held et al., 2004; Zhang et al., 2004). Recent experimental evidence for oligomerization reactions in organic aerosols indicated the need to readdress the current assumptions in models about the partitioning of oxidation products (Kalberer et al., 2004). Applications of aerosol models are partly limited due to the lack of speciated aerosol measurements at high temporal and spatial resolution. Most of the aerosol model applications have been performed in the United States and Canada (Held et al., 2004; Yin et al., 2004). In Europe, there are relatively few applications (Bessagnet et al., 2004; Cousin et al., 2005). In Switzerland, there is hardly any model study on aerosols yet (Andreani-Aksoyoglu et al., 2003, 2004). In view of the forthcoming European legislation on particles, air quality simulations including aerosol processes are urgently needed. This study on modeling of secondary aerosols will provide more information in this field.
2. Modeling method
In this study, the three-dimensional photochemical model CAMx (Comprehensive Air Quality Model with Extensions, version 4.11s) was used with two nested domains (Environ, 2003). The coarse domain is 945 km 783 km with a resolution of 27 km 27 km. The fine domain has a resolution of 9 km 9 km and covers all Switzerland and the greater Milan area. There are 10 s-layers in a terrain-following coordinate system (Lambert Conic Conformal). Simulations started on August 4, 2003 at 0000 UTC and ended on August 7, at 2400 UTC. Meteorological data were calculated by the MM5 meteorological model (PSU/NCAR, 2004). MM5 was initialized by data of the Alpine Model (aLMo) of MeteoSwiss. The emission inventory was prepared by compiling European and Swiss
Modeling of Secondary Aerosols in Switzerland in Summer 2003
77
anthropogenic emissions from various data sources. Using land-use and meteorological data, biogenic emissions were calculated by means of temperature and irradiance dependent algorithms. Initial and boundary conditions were obtained from the regional European model REM-3/ CALGRID. Calculations of aerosols with do2.5 mm were performed with the fine/coarse option of the aerosol module. Primary particle emissions were not considered due to the lack of a particle emission inventory. The CBM-IV mechanism with the extensions for aerosol modeling (mechanism 4) was used for the simulations of this study (Gery et al., 1989). Dry deposition of gases is based on the resistance model of Wesely (1989). The aerosol precursors are supplied to the aerosol chemistry module, which performs the following processes: aqueous sulfate and nitrate formation in cloud water using the RADM aqueous chemistry algorithm (Chang et al., 1987), partitioning of condensable organic gases to secondary organic aerosols to form a condensed organic solution phase using a semivolatile equilibrium scheme called SOAP (Strader et al., 1998), partitioning of inorganic aerosol constituents (sulfate, nitrate, ammonium, sodium, and chloride) between the gas and particle phases using the ISORROPIA thermodynamic module (Nenes et al., 1998).
3. Results and discussion 3.1. Secondary aerosols
The modeled secondary PM2.5 concentrations averaged over the entire period varied between 5 and 10 mg m 3. As seen in Fig. 1, the highest afternoon secondary aerosol mass concentrations were predicted in the polluted area of Milan. The relatively higher levels in the southern part of Switzerland are probably due to the vicinity of the Milan area with high emissions of gaseous precursors for secondary aerosols and the thermal winds towards the Alps advecting also high ozone concentrations. The diurnal variations of predicted individual particulate components in Fig. 2 show a good correlation between ammonium and nitrate concentrations at locations in the north such as Zurich whereas sulfate levels remain almost constant, around 3 mg m 3. These results suggest that in northern Switzerland, enough ammonia exists to neutralize sulfate and then to produce ammonium nitrate. On the other hand, at the southern site Lugano, nitrate levels are very low, and sulfate and ammonium are well correlated. Around Milan, aerosol concentrations are higher than in Switzerland. The average secondary PM2.5 during the studied period is about 15 mg m 3. Especially sulfate concentrations are higher than those
S. Andreani-Aksoyoglu et al.
78
Y (km)
100
0
−100
−200 −300
−200
−100
0 x (km)
100
200
Figure 1. Modeled total secondary aerosol (o2.5 mm) mass concentrations (mg m 3) on 7 August 2003, 1500 UTC.
in the north. At night and in the morning, the correlation between nitrate and ammonium at both Zurich and Milan indicates the formation of ammonium nitrate. The sulfate and ammonium peaks at southern sites in the afternoon show ammonium sulfate production. The model results are compared with all the available ambient aerosol measurements (Fisseha et al., 2005; Hueglin et al., 2005). Measurements of inorganic aerosols are available only for the years 1998 and 2002. The measured PM2.5 concentrations were higher in August 2003 than in previous years. Assuming that the relative increase in measured PM2.5 was the same also for the inorganic aerosol concentrations, the sum of sulfate, nitrate and ammonium for 2003 was estimated. These estimations are close to the model predictions. In order to make a better validation, more detailed measurements of aerosol species are needed. Calculations suggest that the contribution of biogenic SOA to total SOA is rather high, about 70% in the north. 14C measurements of different carbonaceous particle fractions from ambient aerosols showed that the water soluble organic compounds (WSOC) comprised 65–82% biogenic carbon at Zurich in summer 2002 (Szidat et al., 2004). The reported SOA concentration of 2.3 mg m 3 and the high biogenic fraction (65–82%) agree very well with the model prediction of 2.7 mg m 3 and
Modeling of Secondary Aerosols in Switzerland in Summer 2003 zurich secondary PM2.5 (microg/m3)
secondary PM2.5 (microg/m3)
payerne 40
(thick) sec. PM2.5 NO3 SO4
30
(thin) NH4 SOA
20
10 0 24
12
24
12
24
12
24
12
40
(thick) sec. PM2.5 NO3 SO4
30
(thin) NH4 SOA
20
10 0
24
12
24
4 - 7 August 2003
12
NO3 SO4 (thin) NH4 SOA
20
10
12
24
12
24
12
4 - 7 August 2003
12
24
12
24
24
12
24
milano secondary PM2.5 (microg/m3)
secondary PM2.5 (microg/m3)
lugano (thick) sec. PM2.5
0 24
24
4 - 7 August 2003
40 30
79
24
12
24
40 (thick) sec. PM2.5 NO3
30
SO4 (thin) NH4 SOA
20
10 0 24
12
24
12
24
12
4 - 7 August 2003
Figure 2. Diurnal variation of modeled secondary particle (o2.5 mm) concentration (mg m 3) at Payerne (rural), Zurich (urban, north), Lugano (urban, south), Milan (urban, Italy).
65% biogenic contribution in Zurich. On the other hand, the biogenic contribution to SOA is substantially lower in southern Switzerland (about 40%) and around the polluted area in northern Italy (15–25%). In order to check for the effects of initial and boundary conditions (IC and BC, respectively) two more simulations using different IC and BC values for particles were carried out. The concentrations of gaseous species were the same in all cases. In the first case (set 1), no particle concentration was given in the IC and BC files; therefore, the model uses the constant default values (1.10 9 mg m 3) for particles. In the second case (set 2), annual means of long-term measurements at a rural site were used (Hueglin et al., 2005). The last case (set 3) is the base case where IC and BC were taken from the REM3/CALGRID output and the data are variable in time and space. Results of these tests are shown in Fig. 3 for Zurich. The use of low data (set 1) leads to the lowest values during the first two days. On the other hand, results of simulations using long-term measurements (set 2) are slightly higher than the base case (set 3). Differences between various cases are evident for the first 36 h. Later on, the results of all three cases are similar.
S. Andreani-Aksoyoglu et al.
80 zurich 40
secondary PM2.5 (microg/m3)
set 1 set 2 set 3 30
20
10
0 24
12
24
12
24 12 4 − 7 August 2003
24
12
24
Figure 3. Sensitivity of modeled secondary aerosols to initial (IC) and boundary conditions (BC) at Zurich. Set 3 refers to the base case.
3.2. Sensitivity to NH3 and HNO3
The reaction of ammonium with sulfate leads to the formation of ammonium sulfate. After all available sulfate is neutralized, ammonia reacts with nitric acid leading to the formation of ammonium nitrate. The concentration of ammonia is, therefore, crucial for aerosol formation. At low ammonia levels, formation of ammonium nitrate is limited by the availability of ammonia. On the other hand, in regions with high ammonia concentrations, ammonium nitrate formation may depend on the availability of nitric acid. In order to investigate the sensitivity of aerosol formation to emissions, additional simulations were carried out with 50%, 70%, and 90% emissions of NH3 and NOx separately. The sum of the secondary aerosol concentrations was calculated for each case. The relative changes in the diurnal variation of total secondary aerosol mass concentrations due to various reductions of NH3 and NOx emissions give detailed information about the sensitivity of aerosol formation on emissions (Fig. 4). Under the conditions used in this study, aerosol formation in Switzerland is unlikely to be limited by ammonia. In the region of Milan on the other hand, aerosol formation seems to be more sensitive to
Modeling of Secondary Aerosols in Switzerland in Summer 2003
−40 −60 24 12 24 12 24 12 24 12 24
0 −20 −40 −60 24 12 24 12 24 12 24 12 24
4 − 7 August 2003
20
lugano 90% NH3 70% NH3 50% NH3
0 −20 −40
40 20 0 −20 −40
4 − 7 August 2003
0 −20 −40 −60 24 12 24 12 24 12 24 12 24 4 − 7 August 2003
40 change in aerosol mass (%)
change in aerosol mass (%)
20
−20 −40
40 20
−20 −40 −60 24 12 24 12 24 12 24 12 24
20
4 − 7 August 2003
milano 90% NOx 70% NOx 50% NOx
0 −20 −40 −60 24 12 24 12 24 12 24 12 24 4 − 7 August 2003
lugano 70% NOx 70% NO3
0
4 − 7 August 2003
milano 90% NH3 70% NH3 50% NH3
0
4 − 7 August 2003
lugano 90% NOx 70% NOx 50% NOx
zurich 70% NOx 70% NO3
−60 24 12 24 12 24 12 24 12 24
−60 24 12 24 12 24 12 24 12 24
−60 24 12 24 12 24 12 24 12 24
40
20
4 − 7 August 2003
change in aerosol mass (%)
change in aerosol mass (%)
40
40 change in aerosol mass (%)
−20
20
zurich 90% NOx 70% NOx 50% NOx
change in aerosol mass (%)
0
40
40 change in aerosol mass (%)
20
zurich 90% NH3 70% NH3 50% NH3
change in aerosol mass (%)
change in aerosol mass (%)
40
81
20
milano 70% NOx 70% NO3
0 −20 −40 −60 24 12 24 12 24 12 24 12 24 4 − 7 August 2003
Figure 4. Diurnal variation of the change in secondary aerosol mass (%) relative to base case for various NH3 (left) and NOx (middle) emissions. Comparison of the effect of NOx and NH3 emissions on secondary aerosol mass is shown on the right for 30% reduction.
ammonia levels. However, it has to be kept in mind that such sensitivity analyses strongly depend on NH3 emissions, which have high uncertainties. The time when the changes occur differs from one site to the other. In Zurich, in the north of the Alps, reduction in aerosol levels takes place mainly at night and during the morning hours and corresponds to the nitrate peak. In Lugano, south of the Alps, a relatively small decrease in the aerosol concentration due to reduced emissions corresponds to sulfate peaks in the afternoon. The reduction of NOx emissions is predicted to be
82
S. Andreani-Aksoyoglu et al.
more effective to reduce secondary aerosol mass concentrations in Zurich than in Lugano. In Milan, in northern Italy, the results look different than in the two locations in Switzerland. Both, the nitrate peak in the morning and the sulfate peak in the afternoon, decrease when ammonia emissions are reduced. On the other hand, the reduction of NOx emissions leads to a decrease in nitrate in the morning. The aerosol mass increases at noon due to increasing particulate sulfate concentrations. Ozone concentrations increase when NOx emissions are reduced as expected at urban areas with high emissions. The increase in ozone and OH concentrations is probably the cause of the increase in particulate sulfate levels. Aerosol formation seems to be similarly dependent on HNO3 and NH3 most of the time, although there are times when limitation is stronger by ammonia.
4. Conclusions
The modeled average secondary aerosol mass concentrations in Switzerland were predicted to vary between 5 and 10 mg m 3 depending on the location. Comparisons with a few available measurement data suggest that the CAMx model is able to reproduce the secondary aerosol formation and distribution reasonably well. As suggested also by the PM2.5 measurements, the modeled secondary particle concentrations are higher in southern Switzerland. This is most probably due to the vicinity of the polluted Milan area with high emissions of precursors and the thermal winds advecting the pollutants towards the Alps as well as to higher solar radiation increasing photochemical activity. Sensitivity tests indicate that the initial and boundary conditions could affect the modeled particle concentrations especially during the first 36 h. Formation of inorganic aerosols in northern Switzerland is predicted to be limited by nitric acid and therefore by NOx emissions, while it is similarly dependent on nitric acid and ammonia around Milan. The model prediction of a high biogenic SOA fraction (about 70%) in northern Switzerland is supported by the 14C data. This high fraction can be attributed to the large amount of monoterpene emissions in the Swiss Plateau. In southern Switzerland the biogenic contribution to SOA formation drops to 40%. In northern Italy anthropogenic sources contribute much more to SOA formation, supporting our previous calculations. For further studies in this field, a complete emission inventory including the primary particle emissions as well as more aerosol measurements are needed.
Modeling of Secondary Aerosols in Switzerland in Summer 2003
83
Discussion
M. Kaasik: S. Andreani-Aksoyoglu:
How did you calculate the biogenic VOC emissions? Biogenic emissions were calculated using temperature and irradiance dependent algorithms as described in AndreaniAksoyoglu, Keller, 1995. J. Atmos. Chem. 20, 71–87; and Keller et al., 1995. Air Pollution III, WIT Publications. We have a detailed speciation of forest types, not only as deciduous and coniferous, which is very important for biogenic emissions.
ACKNOWLEDGMENTS
We are grateful to the following people for providing various data: F. Schubiger and C. Voisard (MeteoSwiss), R. Stern (FUB), A. Graff (UBA), M. van Loon (TNO), R. Zbinden, M. Keller and J. Heldstab (INFRAS), Th. Kuenzle and B. Rihm (METEOTEST), S. Szidat (University of Bern), C. Hueglin (EMPA), and R. Weber (BUWAL). This project was supported by BUWAL as well as the SBF in the framework of the Network of Excellence ACCENT.
REFERENCES Andreani-Aksoyoglu, S., Keller, J., Dommen, J., Pre´voˆt, A.S.H., 2003. Modelling of air quality with CAMx: A case study in Switzerland. Water, Air & Soil Pollution: Focus 3, 281–296. Andreani-Aksoyoglu, S., Pre´voˆt, A.S.H., Baltensperger, U., Keller, J., Dommen, J., 2004. Modeling of formation and distribution of secondary aerosols in the Milan area (Italy). J. Geophys. Res. 109, doi:10.1029/2003JD004231. Bessagnet, B., Hodzic, A., Vautard, R., Beekmann, M., Cheinet, S., Honore, C., Liousse, C., Rouil, L., 2004. Aerosol modeling with CHIMERE: Preliminary evaluation at the continental scale. Atmos. Environ. 38, 2803–2817. Chang, J.S., Brost, R.A., Isaksen, I.S.A., Madronich, S., Middleton, P., Stockwell, W.R., Walcek, C.J., 1987. A three-dimensional eulerian acid deposition model: Physical concepts and formulation. J. Geophys. Res. 92, 14681–614700. Cousin, F., Liousse, C., Cachier, H., Bessagnet, B., Guillaume, B., Rosset, R., 2005. Aerosol modeling and validation during ESCOMPTE 2001. Atmos. Environ. 39, 1539–1550. Environ., 2003. User’s Guide, Comprehensive Air Quality Model with Extensions (CAMx), Version 4.00. Environ. International Corporation, California.
84
S. Andreani-Aksoyoglu et al.
Fisseha, R., Dommen, J., Gutzwiller, L., Weingartner, E., Gysel, M., Emmenegger, C., Kalberer, M., Baltensperger, U., 2005. Seasonal and diurnal characteristics of water soluble inorganic compounds in the gas and aerosol phase in the Zurich area. Atmos. Chem. Phys. Discuss. 5, 5809–5839. Gehrig, R., Buchmann, B., 2003. Characterizing seasonal variations and spatial distribution of ambient PM10 and PM2.5 concentrations based on long-term Swiss monitoring data. Atmos. Environ. 37, 2571–2580. Gery, M.W., Whitten, G.Z., Killus, J.P., Dodge, M.C., 1989. A photochemical kinetics mechanism for urban and regional scale computer modeling. J. Geophys. Res. 94, 925–956. Hass, H., Loon, M. v., Kessler, C., Stern, R., Matthijsen, J., Sauter, F., Zlatev, Z., Langner, J., Foltescu, V., Schaap, M., 2003. Aerosol modeling: Results and intercomparison from European regional-scale modeling systems. A contribution to EUROTRAC-2 subproject GLOREAM. Held, T., Ying, Q., Kaduwela, A., Kleeman, M., 2004. Modeling particulate matter in the San Joaquin Valley with a source-oriented externally mixed three-dimensional photochemical grid model. Atmos. Environ. 38, 3689–3711. Hueglin, C., Gehrig, R., Baltensperger, U., Gysel, M., Monn, C., Vonmont, H., 2005. Chemical characterization of PM2.5, PM10 and coarse particles at urban, near-city and rural sites in Switzerland. Atmos. Environ. 39, 637–651. IPCC, 2001. Climate change 2001: The scientific basis. Contribution of working group I to the third assessment report of the international panel on climate change. Cambridge University Press, Cambridge, UK, New York, USA. Kalberer, M., Paulsen, D., Sax, M., Steinbacher, M., Dommen, J., Pre´voˆt, A.S.H., Fisseha, R., Weingartner, E., Frankevic, V., Zenobi, R., Baltensperger, U., 2004. Identification of polymers as major components of atmospheric organic aerosols. Science 303, 1659–1662. Nenes, A., Pandis, S.N., Pilinis, C., 1998. ISORROPIA: A new thermodynamic equilibrium model for multiphase multicomponent inorganic aerosols. Aquat. Geoch. 4, 123–152. PSU/NCAR, 2004. MM5 Version 3 Tutorial Presentations. Schell, B., Ackermann, I.J., Hass, H., Binkowski, F.S., Ebel, A., 2001. Modeling the formation of secondary organic aerosol within a comprehensive air quality model system. J. Geophys. Res. 106, 28275–28293. Strader, R., Gurciullo, C., Pandis, S.N., Kumar, N., Lurmann, F.W., 1998. Development of gas-phase chemistry, secondary organic aerosol, and aqueous-phase chemistry modules for PM modeling. Sonoma Technology, Inc., Petaluma, CA, STI-97510-1822-FR. Szidat, S., Jenk, T.M., Gaggeler, H.W., Synal, H.-A., Fisseha, R., Baltensperger, U., Kalberer, M., Samburova, V., Reimann, S., Kasper-Giebl, A., Hajdas, I., 2004. Radiocarbon (14C)-deduced biogenic and anthropogenic contributions to organic carbon (OC) of urban aerosols from Zurich, Switzerland. Atmos. Environ. 38, 4035–4044. Wesely, M.L., 1989. Parameterization of surface resistances to gaseous dry deposition in regional-scale numerical models. Atmos. Environ. 23, 1293–1304. Yin, D., Jiang, W., Roth, H., Giroux, E., 2004. Improvement of biogenic emissions estimation in the Canadian Lower Fraser Valley and its impact on particulate matter modeling results. Atmos. Environ. 38, 507–521. Zhang, Y., Pun, B., Vijayaraghavan, K., Wu, S.-Y., Seigneur, C., Pandis, S.N., Jacobson, M.Z., Nenes, A., Seinfeld, J. H., Binkowski, F.S., 2004. Development and application of the model of aerosol dynamics, reaction, ionization and dissolution (MADRID). J. Geophys. Res. 109, doi:10.1029/2003JD003501.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06022-6
85
Chapter 2.2 Application of the CMAQ mercury model for U.S. EPA regulatory support$ O. Russell Bullock Jr. and Thomas Braverman Abstract On March 15, 2005, the U.S. Environmental Protection Agency (EPA) issued its Clean Air Mercury Rule (CAMR) to permanently cap and reduce mercury emissions from coal-fired Electric Generating Units (EGUs). Part of the development of the CAMR involved simulations of atmospheric mercury emission, transport and deposition across a large part of North America using a special version of the Community Multi-scale Air Quality (CMAQ) model to assess the expected decrease in mercury deposition from various emission control options. CMAQ model simulations of a 2001 base case and a 2020 case with full implementation of the CAMR and the separate Clean Air Interstate Rule (CAIR) showed that mercury emissions from EGUs are expected to decrease by 48% by 2020. Emission reductions of 68% were shown for reactive gaseous mercury, the form of mercury most readily deposited from the atmosphere. Simulated wet deposition of atmospheric mercury for 2001 was compared to observations from the Mercury Deposition Network (MDN). The CMAQ modeling was able to resolve about 60% of the observed site-to-site variance. The modeling also showed that the reduction in mercury deposition expected by 2020 from the CAIR and CAMR is similar to that which would have been obtained by completely eliminating mercury emissions from EGUs in the U.S. in 2001. Most of the emission reductions from the CAMR are in the form of elemental mercury. The CMAQ modeling showed nearly all of these emissions were exported from the modeling domain. Thus, it is expected that the CAMR will result in a reduction of the transport of mercury to other parts of the world. $
This work constitutes a contribution to the NOAA Air Quality Program. Although it has been reviewed by EPA and NOAA and approved for publication, it does not necessarily reflect their policies or views.
O. Russell Bullock Jr. and Thomas Braverman
86 1. Introduction
This paper describes the air quality modeling performed by the U.S. Environmental Protection Agency (EPA) as part of a benefits analysis for the Clean Air Mercury Rule (CAMR). EPA used the Community Multiscale Air Quality (CMAQ) model to simulate mercury (Hg) deposition for a 2001 base case, a 2001 test case with Hg emissions from Electric Generating Units (EGUs) removed from the simulation, and a 2020 case assuming implementation of both the Clean Air Interstate Rule (CAIR) and the CAMR. CMAQ is a three-dimensional Eulerian-type air quality model designed to estimate pollutant concentrations and depositions over a range of spatial scales from urban to continental. For this analysis, CMAQ was applied for an area covering all of the contiguous United States and most of southern Canada and northern Mexico. The boundary and initial pollutant concentrations for all cases were developed from a simulation of 2001 using the GEOS-Chem model, a three-dimensional global atmospheric chemistry and transport model (Yantosca, 2005). Estimates of future-year Hg emissions were obtained through application of EPA’s Integrated Planning Model (IPM) which is described at www.epa.gov/airmarkets/epa-ipm. 2. Emissions inventories and estimated emissions reductions
The CAMR Emissions Inventory Technical Support Document (TSD) provides detailed information on development of the 2001 and 2020 emissions inventories used in this air quality modeling study (U.S. EPA, 2005). These inventories are summarized in Table 1. Approximately 115 Table 1. Summary of mercury emissions by species: 2001 and 2020 Emissions source
Mercury emissions species (tons)
Total mercury (tons)
Elemental
Reactive gaseous
Particulate
26.26 37.85 5.05 69.16
20.58 13.33 1.53 35.44
1.73 7.60 0.96 10.29
48.57 58.78 7.54 114.89
2020 (with CAIR and CAMR) EGUs 17.65 Non-EGU point 28.03 Non-point 5.69 Total, all sources 51.37
6.57 10.37 1.30 18.24
0.83 6.61 0.77 8.21
25.05 45.01 7.76 77.82
2001 base year EGUs Non-EGU point Non-point Total, all sources
CMAQ Mercury Model for U.S. EPA Regulatory Support
87
tons of Hg was emitted from all U.S. sources in 2001 based on the EPA inventory. EGUs emitted 48.6 tons, or 42.3% of Hg emissions from all sources during this base year. About 20.6 tons of reactive gaseous Hg (RGM) was emitted by these EGUs, comprising 42.4% of their total Hg emissions in all forms. The 2020 emissions inventory accounts for increases in economic activity and population growth between 2001 and 2020, as well as implementation of regulatory policies from Maximum Achievable Control Technology (MACT) standards (primarily on non-EGU sources) and CAIR and CAMR controls as applied to EGUs in the U.S. Total anthropogenic Hg emissions in 2020 are estimated at roughly 78 tons, reflecting a net reduction of about 37 tons (or 32%) from 2001 levels. The reduction in Hg emissions from EGUs is over 23 tons, a 48% reduction from 2001 levels. EGU emissions of RGM, the most rapidly deposited form of Hg, are reduced by 14 tons or 68% relative to 2001.
3. Model description
The CMAQ modeling system is a comprehensive three-dimensional gridbased Eulerian air quality model designed to operate on a range of domain sizes from urban to continental (Byun and Schere, 2006). CMAQ reflects the state-of-the-science in addressing the atmospheric processes critical for simulating oxidant precursors and non-linear chemistry associated with the transformation and deposition of Hg. CMAQ version 4.3 was used as a basis for Hg modeling for CAMR. Various updates to the base model were made to improve the underlying science and address comments from peer review. The updates in Hg chemistry used for CAMR from those described in the first published version of the CMAQ Hg model (Bullock and Brehme, 2002) are as follows: (1) the gaseous elemental Hg (Hg0) reaction with H2O2 assumes the formation of RGM rather than particulate Hg (PHg); (2) the gaseous Hg0 reaction with ozone assumes the formation of 50% RGM and 50% PHg rather than 100% PHg; (3) the gaseous Hg0 reaction with OH assumes the formation of 50% RGM and 50% PHg rather than 100% PHg; and (4) the kinetic rate constant for the gaseous Hg0+OH reaction was lowered slightly to 7.7 10 14 cm3 molecules 1 s 1. CMAQ requires a variety of input files that contain information pertaining to the modeling domain and simulation period. These include hourly emissions estimates and meteorological data in every grid cell as well as a set of pollutant concentrations to initialize the model and to specify concentrations along the boundaries of the modeling domain.
88
O. Russell Bullock Jr. and Thomas Braverman
Key science options for the CMAQ as applied for the CAMR analysis include: Gas-phase chemical solver: Euler Backward Iterative (EBI) scheme Advection scheme (vertical and horizontal): Piecewise Parabolic Method (PPM) Vertical diffusion: K-theory eddy diffusivity with 1 m2 s 1 minimum Dry deposition: M3DRY module with Pleim-Xiu land surface model Aqueous chemistry: RADM bulk scheme Cloud scheme: RADM cloud scheme Vertical coordinate: Terrain-following sigma-pressure coordinate 3.1. CMAQ modeling domain and configuration
The CMAQ horizontal modeling domain employed for this study encompasses all of the lower 48 states and a large part of Canada and Mexico and consists of 16,576 grid cells with dimensions of 36 km by 36 km. The vertical modeling domain contains 14 layers extending from the surface to the 10 kPa (100 mbar) pressure level in a sigma-pressure terrain-following coordinate system. 3.2. Time period modeled for mercury deposition
CMAQ was run for a full calendar year using 2001 meteorology and boundary concentration data for each of the scenarios modeled. The overall wall-clock time for completing an annual simulation was reduced by dividing the year into two 6-month periods, which were simulated in parallel. One simulation was for January through June and the other was for July through December. Each 6-month simulation included a 10-day ‘‘spin-up’’ period designed to minimize the influence of the initial condition used at the start of the simulation. Model predictions from these spin-up periods were not used in analyses of the modeling results. The meteorological conditions, initial conditions and boundary conditions (BCs) were the same for each of the annual scenarios modeled. 3.3. Meteorological inputs to CMAQ
The CMAQ model requires a specific suite of meteorological input files in order to simulate the physical and chemical processes affecting Hg and the other pollutants. Meteorological input files were derived from a simulation of the Pennsylvania State University/National Center for Atmospheric Research Mesoscale Model (Grell et al., 1994) for the entire year
CMAQ Mercury Model for U.S. EPA Regulatory Support
89
of 2001. This limited-area, non-hydrostatic model is commonly referred to as MM5. For this analysis, version 3.6.1 of MM5 was used. The MM5 horizontal domain consisted of 36 36 km grid cells just like the CMAQ domain, except the MM5 domain was expanded by six grid cells on all four sides to avoid boundary effects from the meteorological model being incorporated into the CMAQ chemical modeling. The MM5 vertical domain was comprised of 34 layers interspersed within the 14 CMAQ layers using the same sigma-pressure coordinate system. Some of the key model physics options employed were as follows:
Cumulus parameterization: Kain-Fritsch Planetary boundary layer scheme: Pleim-Chang Explicit moisture scheme: Reisner 2 Radiation scheme: RRTM longwave scheme Land surface model: Pleim-Xiu Four-dimensional data assimilation (FDDA): analysis nudging only
The MM5 outputs were processed to create model-ready inputs for CMAQ using the Meteorology–Chemistry Interface Processor (MCIP) (U.S. EPA, 1999). MCIP version 2.2 gvm was used to convert the MM5 output to CMAQ meteorological input. This version contained two differences from the main MCIP version 2.2 in that (1) it allowed for treatment of the graupel associated with the Reisner 2 microphysics scheme and (2) it included a patch to compensate for a minor error in MM5 associated with vegetation fractions. 3.4. Initial and boundary condition inputs to CMAQ
Limited-area modeling as performed for this analysis requires the definition of BCs to account for the influx of pollutants and precursors from upwind source areas outside the modeling domain. A number of recent studies show that long-range, intercontinental transport of pollutants is important for simulating seasonal/annual ozone, PM and Hg (Jacob et al., 1999; Fiore et al., 2003; Jaffe et al., 2003; Selin, 2005). A commonly employed approach to estimate incoming pollutant concentrations associated with intercontinental transport is to use a global chemistry model to provide dynamic BCs for the regional model simulations. For all CAMR Hg modeling cases, we used an annual simulation of calendar year 2001 obtained from a global three-dimensional chemistry model, the GEOS-Chem model (Yantosca, 2005), to provide the BCs and initial concentrations. The global GEOS-Chem model simulates atmospheric chemical and physical processes driven by assimilated meteorological observations from the NASA Goddard Earth Observing System (GEOS).
90
O. Russell Bullock Jr. and Thomas Braverman
This model was run for the entire year with a grid resolution of 2.01 2.51 (latitude–longitude) and 20 vertical layers. The results were used to provide one-way dynamic BCs at 3-h intervals and initial concentration field for all CMAQ simulations. We used an interface utility tool developed at the University of Houston (Moon and Byun, 2004) to link the GEOSChem with CMAQ. 3.5. CMAQ model applications
For this analysis, the following modeling cases were studied: a 2001 base case, a 2001 test case with utility Hg emissions zeroed-out and a 2020 projection with CAIR, CAMR and all expected non-utility Hg controls incorporated. 4. CMAQ model performance evaluation
An operational model performance evaluation for Hg wet deposition for 2001 was performed to estimate the ability of the CMAQ modeling system to replicate base-year wet depositions of Hg. Comparisons of model predictions to the corresponding measurements from the Mercury Deposition Network (MDN) were made. Only sites where data was available for more than half of all four seasons were used for the annual performance evaluation. There were 52 MDN sites in 2001 that meet the data completeness requirements, of those sites 48 were located east of 1001W and 4 were located west of 1001W. A scatter plot of the observed versus predicted annual Hg wet deposition for all the sites is shown in Fig. 1. Although the CMAQ model tends to underestimate Hg wet deposition to a small degree, the majority of predictions are within 30% of observed values. Most of the remaining sites have predictions that are within 50% of observations. There is one MDN site in British Columbia where the model overestimates by greater than a factor of 2. However, the precipitation at this site was overestimated by the meteorological input model by 55%. With this observation removed from the analysis, CMAQ was able to explain 60% of the variance in the observed data. 5. Impacts of CAMR on mercury depositions
Total Hg deposition for the 2001 base case as simulated by the CMAQ model is displayed in Fig. 2. The simulated reduction in total Hg deposition resulting from elimination of all U.S. power plant Hg emissions in 2001 is presented in Fig. 3. The projected reduction in total Hg deposition
CMAQ Mercury Model for U.S. EPA Regulatory Support
91
Figure 1. Comparison of CMAQ-simulated total Hg wet deposition for 2001 to observations from the Mercury Deposition Network (MDN).
Figure 2. Total Hg deposition (mg m 2) from the base-case 2001 simulation of CMAQ.
92
O. Russell Bullock Jr. and Thomas Braverman
Figure 3. Percent reduction in mercury deposition from the 2001 base case when EGU mercury emissions are eliminated.
Figure 4. Percent reduction in mercury deposition from the 2001 base case when CAMR, CAIR and other non-utility emission controls are implemented in 2020.
CMAQ Mercury Model for U.S. EPA Regulatory Support
93
from the 2001 base case when CAMR, CAIR and other non-utility emission controls are implemented in 2020 is given in Fig. 4. The modeling results reveal that the reduction in Hg deposition stemming from the implementation of CAIR, CAMR and other minor non-utility Hg emission decreases by 2020 is similar to that obtained by completely eliminating EGU Hg emissions in the U.S. in 2001. CAIR eliminates over 60% of RGM emissions from EGUs through the implementation of scrubber control technology. However, most of the Hg emission reductions from CAMR are in the form of Hg0. This form of Hg is not readily deposited and nearly all of it is transported outside the modeling domain with no impact on the Hg deposition flux in the modeling domain. Thus, it is expected that CAMR will result in a reduction of the transport of Hg to other parts of the world. Discussion
B. Fisher:
O.R. Bullock Jr.:
M. Sofiev:
O.R. Bullock Jr.:
Could you explain what kind of mercury specific controls will be applied to U.S. generating units to achieve the 2020 mercury emission limit? Much of the mercury control expected in 2020 will be achieved as a co-benefit from sulfur controls that are a part of the U.S. EPA’s Clean Air Interstate Rule. The Clean Air Mercury Rule specifies emission reductions for mercury, but does not dictate the technology that is to be used. The U.S. EPA believes that carbon particle injection and recovery can achieve the necessary mercury emission reductions, but any other suitable technology that may be developed can be used. Hg is known to have a very inertial background contamination level (1.5 ng m 3). Have you seen any impact of the U.S. emission measures to this level? Is the territory of the U.S. a net importer or exporter of the Hg species? Assessment of the expected impact of U.S. mercury emission reductions on the global background level would require global-scale modeling that the U.S. EPA has not yet performed. However, we know that the U.S. electric utility emissions of mercury are currently a very small fraction of the total mercury emission flux worldwide, so we would expect the impact of these future controls on the background level to be minimal. Our modeling shows total
O. Russell Bullock Jr. and Thomas Braverman
94
mercury deposition to the U.S. is larger than the current industrial emission flux of mercury. In that sense, you could say that the U.S. is a net importer. However, this does not take into account emissions of mercury from natural processes that take place in the U.S. Those emissions are a combination of natural geologic mercury and mercury from past atmospheric deposition that is revolatilized. Therefore, the question of import versus export of mercury is very complicated and has no certain answer. ACKNOWLEDGMENTS
The research presented here was performed under the Memorandum of Understanding between the U.S. Environmental Protection Agency (EPA) and the U.S. Department of Commerce’s National Oceanic and Atmospheric Administration (NOAA) and under agreement number DW13921548. REFERENCES Bullock, O.R., Brehme, K.A., 2002. Atmospheric mercury simulation using the CMAQ model: Formulation, description, and analysis of wet deposition results. Atmos. Environ. 36, 2135–2146. Byun, D., Schere, K.L., 2006. Review of the governing equations, computational algorithms, and other components of the models-3 Community Multiscale Air Quality (CMAQ) modeling system. Appl. Mech. Rev. 59, 51–77. Fiore, A.M., Jacob, D.J., Liu, H., Yantosca, R.M., Fairlie, T.D., Li, Q., 2003. Variability in surface ozone background over the United States: Implications for air quality policy. J. Geophys. Res. 108, 4787–4803. Grell, G.J., Dudhia, J., Stauffer, D., 1994. A description of the fifth-generation Penn State/ NCAR Mesoscale Model (MM5). Publication NCAR/TN-398+STR. National Center for Atmospheric Research, Boulder, Colorado, p. 138. Jacob, D.J., Logan, J.A., Murti, P.P., 1999. Effect of rising Asian emissions on surface ozone in the United States. Geophys. Res. Lett. 26, 2175–2178. Jaffe, D., McKendry, I., Anderson, T., Price, H., 2003. Six ‘new’ episodes of trans-Pacific transport of air pollutants. Atmos. Environ. 37, 391–404. Moon, N.K., Byun, D.W., 2004. A simple user’s guide for GEOS2CMAQ code: Linking CMAQ with GEOS-Chem, version 1.0. Interim Report from Institute for Multidimensional Air Quality Studies (IMAQS), University of Houston, TX. Selin, N.E., 2005. Mercury rising: Is global action needed to protect human health and the environment? Environment. 47, 22–35. U.S. EPA, 1999. Science algorithms of the EPA models-3 Community Multi-scale Air Quality (CMAQ) modeling system. U.S. Environmental Protection Agency publication EPA/600/R-99/030.
CMAQ Mercury Model for U.S. EPA Regulatory Support
95
U.S. EPA, 2005. Clean air mercury rule emission inventory technical support document. U.S. Environmental Protection Agency web publication, http://www.epa.gov/ttn/atw/ utility/emiss_inv_oar-2002-0056-6129.pdf Yantosca, B., 2005. GEOS-Chem v7-03-06 User’s Guide. Atmospheric Chemistry Modeling Group, Harvard University, Cambridge, MA, posted 8 November 2005 at http:// www-as.harvard.edu/chemistry/trop/geos/doc/man/index.html
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06023-8
96
Chapter 2.3 Multi-objective analysis to control ozone exposure Claudio Carnevale, Giovanna Finzi, Enrico Pisoni and Marialuisa Volta Abstract Regional authorities need suitable tools to develop air quality plans, in particular when dealing with secondary pollutants, such as ozone, characterized by complex and non–linear dynamics. This work presents a two objective problem considering both effectiveness and costs of alternative environmental policies. To solve the multiobjective problem, an integrated modeling system has been designed and implemented. It includes (1) pollutant-precursor models identified by processing the simulations of the GAMES modeling system, and (2) cost functions computing emission reduction costs. The methodology has been applied to a complex domain in Northern Italy, including Milan metropolitan area, a region characterized by high ozone levels in the summer season. 1. Introduction
In recent years, tropospheric secondary pollution (namely PM10 and ozone) episodes have become more and more critical all over Europe. A major task of regulatory agencies is to develop plans to mitigate such heavy pollution episodes and direct their effort towards a stable solution of this problem. These plans must be formulated in terms of precursor emission reduction, as nitrogen oxides (NOx) and volatile organic compounds (VOC). In principle, such reductions should be fixed on the basis of techniques such as cost–benefit analysis, cost-effectiveness analysis (Schleiniger, 1999; Streets et al., 2001) or multi-objective optimization (Finzi and Guariso, 1992). Cost–benefit analysis selects best plans minimizing the sum of two or more objectives, i.e., pollution damages and emission abatement costs. Cost-effectiveness analysis also permits to treat not economically assessable objectives. The multi-objective problem (Finzi and Guariso, 1992; Shih et al., 1998; Scho¨pp et al., 1999; Friedrich
Multi-Objective Analysis to Control Ozone Exposure
97
and Reis, 2000; Guariso et al., 2004) allows to consider separately different objectives. In the multi-objective approach, the pollution–precursor relationship can be simulated by deterministic 3D modeling systems, describing transport and chemical phenomena. Such models have so high computational costs that they are not of practical use in a multi-objective mathematical program. So the identification of simplified models synthesizing the relationship between the precursor emissions and secondary pollutant concentrations is required. To get round the problem, in literature the source–receptor relationship has been described using ozone isopleths (Flagen and Seinfeld, 1988; Loughlin, 1998) or with reduced-form models. The latter can be divided into (1) simplified photochemical models as in Venkatram et al. (1994) and (2) statistical models on the results of deterministic 3D transport-chemical models (long-term simulations in Friedrich and Reis (2000), short-term simulations in Barazzetta et al. (2002). In this paper, a two-objective analysis (air quality and costs) aimed to select effective AOT40 control plans is presented. The non-linear relations between emissions and ozone are identified for Lombardia region (Northern Italy) by means of neural network models, calibrated processing longterm simulations, performed in the frame of Citydelta II project by means of GAMES multi-phase modeling system (Volta and Finzi, 2006). Cost functions are calculated for emission reductions for each CORINAIR macrosector and then the two-objective problem is solved using as decision variables NOx and VOC reductions.
2. Problem formulation
Ground-level ozone control can be formulated as a two-objective mathematical programming problem including the effectiveness of emission reduction policies and their costs. As photochemical pollution is formed from emissions of nitrogen oxides and of VOC in the presence of sunlight, the daily cell exposure to ozone is function of meteorological parameters (that cannot be handled) and of precursor emissions (decision variables). A regional authority can impose a reduction to a certain emission sector, and so the daily cell emissions are expressed with respect to a reference situation and split in 11 sectors according to the CORINAIR classification (EMEP/CORINAIR, 1999). The first objective considered is the minimization of seasonal domain ozone exposure (OE), expressed in terms of seasonal accumulated ozone dose (AOT40) above the 40 ppb cut-off value for daylight hours over a
Claudio Carnevale et al.
98
grid domain. The objective can be expressed as minðOEÞ ¼ min W
D XX
N m V ½AOT40i;j ðN m i;j ðdÞ ð1 rm Þ; V i;j ðdÞ ð1 rm ÞÞ
8i;j d¼1
(1) where AOT40i,j is the daily value of AOT40 for cell i, j; D is the amount of m the summer days; N m i;j ðdÞ and V i;j ðdÞ are respectively the daily cell NOx V and VOC emissions in the reference case for sector m; WðrN m ; rm Þm¼1;...;11 is the decision variable set, namely the percentage of sector precursor emission reductions (respectively for NOx and VOC); m ¼ 1,y,11 is the CORINAIR emission sector. The second objective of the ozone planning is the minimization of precursor (NOx and VOC) emission reduction costs: minðCostsÞ ¼ min W
11 X N N m V V V ðN m rN m cm ðrm Þ þ V rm cm ðrm ÞÞ
(2)
m¼1
with the constraints: N 0 rN m Rm V 0 rV m Rm N V V where cN m ðrm Þ and cm ðrm Þ are functions giving the unit costs related respectively to NOx and VOC emission reduction for sector s; Nm and Vm are the seasonal domain NOx and VOC emissions in the reference case for V sector s; RN m and Rm are the maximum feasible reductions allowed by the available technologies for sector s.
3. Precursor-pollutant models
The precursor–ozone relationship should be given by the results of deterministic 3D modeling system simulations, but they require so high computing times that such models cannot be used in an optimization problem. In this section, neural network precursor–ozone simplified models, tuned processing deterministic 3D modeling system simulations, are formalized and implemented for a domain placed in Northern Italy (Fig. 1), a densely inhabited and industrialized area that is regularly affected by high ozone concentrations.
Multi-Objective Analysis to Control Ozone Exposure
99
5150
SONDRIO TRENTO
5100
(m) 3000
VARESE
2800
BERGAMO
2600
5050
BRESCIA NOVARA
MILANO
2400 VERONA
2200 2000
5000
1800 TORINO
1600 PIACENZA
1400
ALESSANDRIA
1200
PARMA
1000
4950
MODENA
800 600 400
GENOVA
200
4900
0
400
450
500
550
600
650
Figure 1. The simulation domain orography (in meters above sea level).
3.1. GAMES long-term simulations
Ground-level ozone concentrations have been simulated by the GAMES modeling system consisting of (a) the multiphase eulerian 3D photochemical model TCAM (Carnevale et al., 2005) and (b) the meteorological pre-processor CALMET (Scire et al., 1990); the emission processor POEM-PM (Carnevale et al., 2006). The modeling system has been run over Northern Italy (Fig. 1), in the frame of CityDelta-CAFE project. The domain (300 300 km2) has been horizontally subdivided into 60 60 cells, with a resolution of 5 5 km2 each. Vertical domain extends up to 3900 m above sea level, subdivided into 11 layers of growing thickness. Simulations have been performed getting initial and boundary conditions by a nesting procedure from the results of the EMEP Unified Model working at European scale (Simpson et al., 2003). Assuming the actual meteorology, emission scenarios and boundary conditions of that period, the base case simulation has been performed, supplying pollutant hourly concentration fields.
100
Claudio Carnevale et al.
The run of such a simulation takes about 12 days of CPU time, and this explains why GAMES cannot be directly integrated in an optimization procedure that should process hundreds of model runs. Keeping the same meteorology in input and applying two different emission control strategies (current legislation (CLE) and most feasible reduction (MFR), http://www.iiasa.ac.at) reducing ozone precursor emissions, two alternative scenarios have been simulated in the frame of CityDelta-CAFE EU Project (http://aqm.jrc.it/citydelta/). Their outputs have been used for the calibration of the simplified source-receptor models described in the following section. 3.2. Neural network models
Simplified source-receptor models have been set up by means of neural networks. Several network structures have been considered. The chosen architecture for this work is the Elman Neural Network (Elman, 1990). One neural network has been identified for each group of 2 2 (10 10 km2) domain cells. The input data are the daily NOx and VOC emissions estimated for each cell group. The inputs are pre-processed by means of a normalization procedure. The target data are the AOT40 daily mean values computed by the GAMES system. The tuning and validation data series are selected processing the GAMES simulations performed on the three different emission scenarios. Each simulation covers a period from April to September. The validation set has been yielded extracting, from the simulation data set, the third week of each month. The identification set includes the remaining patterns. The identified nets are characterized by the features shown in Table 1. The scatter plot presented in Fig. 2 shows that the neural network system ensures high capability to simulate the non-linear source-receptor relationship between AOT40 and the emission of ozone precursors. The scatter plot highlights that all the points are very close to the bisecting line, even if the identified neural networks slightly overestimate AOT40. Table 1. Neural network architecture NN features Nodes of the input layer Nodes of the output layer Nodes of the hidden layer Training set Validation set
Value 3 1 8 423 126
Multi-Objective Analysis to Control Ozone Exposure
Figure 2. Neural network versus GAMES ozone concentrations on each grid point of the domain.
101
102
Claudio Carnevale et al.
4. Cost functions
In this work, NOx and VOC reductions are considered as decision variables. These reductions are defined according to the CORINAIR emission classification, which considers emissions as grouped in 11 sectors. Not all the sector emission reductions can be considered during the optimization, due to the fact that for some CORINAIR sectors reduction costs are not available; so cost functions cannot be identified. More precisely, macrosectors 1 and 10 are not considered for VOC, while macrosectors 1, 5, 6, 9 and 10 are not considered for NOx reductions. Biogenic emission reductions (macrosector 11) also are not considered. The abatement cost curves used are estimated on the basis of a large data set collected for Italy by RAINS-IIASA database (http://www. iiasa.ac.at). The cost of a unit emission reduction, incurred by adopting several technological alternatives for each activity included in each sector, has been assessed. These data allow to estimate an emission abatement cost function for each sector, fitting the costs and the efficiency of the available technologies (Fig. 3). This fitting has been performed only within zero and the maximum feasible reduction, with the constraint of estimating a monotonically increasing and convex function. As an example, Fig. 3 shows the cost curves estimated for road traffic (SNAP macrosector 7).
5. Results
The base emission scenario implies no costs and produces a reference air pollution index. Instead, if one adopts the best (and more expensive) reduction technologies in all the sectors considered, the cost is about 974,000 Keuro (see Fig. 4) with a decrease of the other objective of about 44% with respect to the base case value. This corresponds to emission reduction close to 40% for VOC and 30% for NOx. Figure 4 (left) depicts the set of non-dominated solutions of the two objective problems. At right in the same figure, the both axes have been rescaled to the maximum feasible variation. In Fig. 5, the values of the decision variables giving the optimal solutions are presented. The figure suggests the set of macrosector emission reductions that are more efficient to reach optimal solutions, in other words, the reduction priorities to be implemented in AOT40 ablation. In terms of absolute values, Fig. 6 stresses the macrosector emissions corresponding to the optimal solution curve.
Multi-Objective Analysis to Control Ozone Exposure
103
VOC 4000
Unit cost (Keuro)
3500 y = 10513x2 + 1671,6x R2 = 0.7942
3000 2500 2000 1500 1000 500 0 0%
10%
20%
30%
40%
50%
Emission reduction (%)
NOX 10000 9000
y = 31114x2 + 12715x R2 = 0.8336
Unit Cost (Keuro)
8000 7000 6000 5000 4000 3000 2000 1000 0 0%
5%
10%
15%
20%
25%
30%
Emission reduction (%)
Figure 3. Cost curves estimated for road traffic (SNAP macrosector 7) for VOC and NOx.
A solution corresponding to 50% of the maximum air quality improvement (in Fig. 4 stressed with a vertical line) can be attained with only 13% of the maximum cost, while the marginal costs grow with the increase of emission reductions. As shown in Fig. 6, to obtain a reduction of 50% of the air quality objective a decision maker needs to focus on solvent use (n. 6), road transport (n. 7) and other mobile sources (n. 8) for VOC reduction, and production processes (n. 4) and road traffic (n. 7) for NOx reduction. The other sectors become of interest only when very strong emission reduction is required.
Claudio Carnevale et al.
104 3,1E+07 2,9E+07
AOT40 (ppb*h)
2,7E+07 2,5E+07 2,3E+07 2,1E+07 1,9E+07 1,7E+07 1,5E+07 0,E+00
1,E+05
2,E+05
3,E+05
4,E+05
5,E+05
6,E+05
7,E+05
8,E+05
9,E+05
1,E+06
Cost (Keuro) 100% 90%
AOT40 reduction (% max)
80% 70% 60% 50% 40% 30% 20% 10% 0% 0%
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
Cost (% max)
Figure 4. Set of non-dominated solutions.
6. Conclusion
A procedure to formulate a multi-objective analysis to control ozone exposure has been presented. The procedure implements Elman neural networks tuned by the output of a deterministic 3D model and cost functions of different emission abatement strategies. The methodology has been applied over a Northern Italy domain, often affected by high ozone levels, using as data set the outputs of the GAMES modeling
Multi-Objective Analysis to Control Ozone Exposure
105
80%
VOC emission reduction (%)
70% 60% S2 S4 S5 S6 S7 S8 S9
50% 40% 30% 20% 10% 0% 0%
20%
40%
60%
80%
100%
AOT40 reduction (% max) 90%
NOx emission reduction (%)
80% 70% 60% S2 S3 S4 S7 S8
50% 40% 30% 20% 10% 0% 0%
20%
40%
60%
80%
100%
AOT40 reduction (% max) Figure 5. VOC and NOx reductions in each sector to generate an optimal solution.
system for three different simulations (a base case and two alternative emission scenarios obtained varying the ozone precursors emission). Results of the optimization point out which are the emission sectors that the regional authorities should first take into consideration to reduce ground-level ozone concentration with minimum abatement costs. Furthermore, it is shown that a consistent reduction of ozone peaks can be attained in Lombardy with a small fraction (about 13%) of the costs of adopting the best reduction technologies.
Claudio Carnevale et al.
106 300000
VOC emissions (ton/year)
250000
2 4 5 6 7 8 9
200000
150000
100000
50000
0 0%
20%
40%
60%
80%
100%
AOT40 reduction (% max) 180000
NOX emissions (ton/year)
160000 140000 120000 2 3 4 7 8
100000 80000 60000 40000 20000 0 0%
20%
40%
60%
80%
100%
AOT40 reduction (% max) Figure 6. VOC and NOx emission required to generate an optimal solution.
Discussion
F. Murena:
Does the neural network model still effectively evaluate O3 concentrations if emission rates are strongly reduced following the optimization procedure?
Multi-Objective Analysis to Control Ozone Exposure
C. Carnevale:
B. Fisher:
C. Carnevale:
E. Genikhovich:
C. Carnevale:
107
During the identification phase, one of the three emission scenarios used concerns the most feasible reduction available for each pollutant. The reductions assumed in this scenario are also used as bounds for the decision variable of the optimization problem; so the emission values in the optimization phase have to be inside the bounds of the identification set. Can one generalize the neural network so that there are more input nodes representing different VOC species with different reactivities? In principle, this generalization is possible. Therefore, due to the increasing in the number of the neural network inputs, a very large number of scenarios have to be simulated by GAMES modeling system in order to create the identification set. In order to avoid the high sensitivity of the optimization plan to the errors in the cost function, one should use a regularization procedure. Did you apply any in your work? In this first analysis, no regularization procedure has been applied, but this is one of the topics we intend to investigate in the future.
ACKNOWLEDGMENTS
This work has been partially supported by the Italian Ministry of University and Research (MIUR). The work has been developed in the frame of CityDelta-CAFE project and ACCENT EU Excellence Network. The authors are grateful to Davide Fasoli (Universita` di Brescia) for his kind and valuable co-operation in data processing.
REFERENCES Barazzetta, S., Corani, G., Guariso, G., 2002. A neural emission-receptor model for ozone reduction planning. In: Proc. iEMSs 2002. Vol. 2. pp. 130–135. Carnevale, C., Finzi, G., Volta, M., 2005. Design and validation of a multiphase 3D model to simulate tropospheric pollution, 44th IEEE Conference on Decision and Control and European Control Conference 2005, Seville (E).
108
Claudio Carnevale et al.
Carnevale, C., Gabusi, V., Volta, M., 2006. POEM-PM: An emission model for secondary pollution control scenarios. Environ. Modell. Softw. 21, 320–329. Elman, J., 1990. Finding structure in time. Cogn. Sci. 14, 179–211. EMEP/CORINAIR, 1999. Atmospheric Emission Inventory Guidebook, second ed. Tech. rep., European Environment Agency. Finzi, G., Guariso, G., 1992. Optimal air pollution control strategies: A case study. Ecol. Model. 64, 221–239. Flagen, R.C., Seinfeld, J.H., 1988. Fundamentals of Air Pollution Engineering. PrenticeHall, Englewood, NJ. Friedrich, R., Reis, S., 2000. Tropospheric Ozone Abatement. Springer-Verlag, Berlin Heidelberg. Guariso, G., Pirovano, G., Volta, M., 2004. Multi-objective analysis of ground level ozone concentration control. J. Environ. Manage. 71, 25–33. Loughlin, D.H., 1998. Genetic algorithm-based optimization in the development of tropospheric ozone control strategies. PhD thesis. Graduate Faculty of North Carolina State University. Schleiniger, R., 1999. Comprehensive cost-effectiveness analysis of measures to reduce nitrogen emissions in Switzerland. Ecol. Econ. 30, 147–159. Scho¨pp, W., Amann, M., Cofala, J., Heyes, C., Klimont, Z., 1999. Integrated assessment of European air pollution emission control strategies. Environ. Modell. Softw. 14, 1–9. Scire, J.S., Insley, E.M., Yamartino, R.J., 1990. Model formulation and User’s Guide for the CALMET meteorological model. Tech. Rep. A025-1, California Air Resources Board, Sacramento, CA. Shih, J., McRae, G.J., Russell, A.G., 1998. An optimization model for photochemical air pollution control. Eur. J. Oper. Res. 106(1), 1–14. Simpson, D., Fagerli, H., Jonson, J., Tsyro, S., Wind, P., 2003. Transboundary acidification, eutrophication and ground level ozone in Europe—Part I: Unified EMEP model description. Tech. Rep. 1/2003, EMEP MSC-W. Streets, D.G., Chang, Y.S., Tompkins, M., Ghim, Y.S., Carter, L.D., 2001. Efficient regional ozone control strategies for eastern United States. J. Environ. Manage. 61, 345–365. Venkatram, A., Karamchandani, P., Pai, P., Goldstein, R., 1994. The development and application of a simplified ozone modelling system (SOMS). Atmos. Environ. 28, 3665–3678. Volta, M., Finzi, G., 2006. GAMES, a comprehensive Gas Aerosol Modelling Evaluation System. Environ. Modell. Softw. 21, 587–594.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06024-X
109
Chapter 2.4 Atmo-rhenA: a common air quality modelling system in the Upper Rhine Valley R. Deprost, J. Bernard, E. Riviere, N. Leclerc and C. Schillinger Abstract The ASPA is in charge of regional air quality assessment and forecast (measurements and modelling), emission inventory realisation and gridding, and population information. In the frame of the European INTERREG III program, it is working together with the networks of Baden Wu¨rttemberg (Landesanstalt fu¨r Umwelt, Messungen und Naturschutz Baden-Wu¨rttemberg, LUBW) and Basel (Lufthygieneamt beider Basel, LHA) towards a ‘‘common air quality assessment and information system in the Upper Rhine Valley’’. The current and last step of the project is the set up of a common regional air quality modelling platform (simulation and forecast), which completes the bilingual website presenting daily measurements of the networks. The Atmo-rhenA platform is based on the CHIMERE (Institut Pierre Simon Laplace, IPSL, http://euler.lmd.polytechnique.fr/ chimere) chemistry-transport model (CTM) and the MM5 meteorological model (National Centre for Atmospheric Research, NCAR). It is fed up with a detailed transboundary inventory update on the domain, integrating a speciation of non-methane volatile organic compounds (NMVOC) (Sambat et al., 2004) and particulate matter (PM) (Pregger et al., 2004) worked out by IER (Institut fu¨r Energiewirtschaft und Rationelle Energieanwendung) and CITEPA (Centre Interprofessionnel Technique d’Etudes de la Pollution Atmosphe´rique). Daily forecasts for the Upper Rhine Valley are operational since the beginning of 2005 and will be soon available on Internet. Indicators on the forecasting performances of the platform are calculated thanks to comparison with the routine measurements. Further, Atmo-rhenA allows the study of ozone production in the Upper Rhine Valley and the simulation of the impact of emission
110
R. Deprost et al.
reduction scenarios on ozone peaks. For instance it has been used to assess the impact of a local short-term scenario (application of emergency measures) and of European long-term scenarios from the European Clean Air For Europe (CAFE) programme, both applied on the transboundary emission cadaster.
1. Introduction and context
During the first INTERREG project between 1993 and 1995, the ASPA and the LUBW realised the atmosphere protection plan for the transboundary space Strasbourg/Ortenau. During the second INTERREG project between 1996 and 2000, the same working community realised a transboundary analysis of the air quality in the Upper Rhine Valley, with emission and immission cadasters of the Valley and geostatistical study of population exposition to NO2 and C6H6 thresholds exceedance. Within the French-German-Swiss Upper Rhine Conference, the Expert Group on Air quality of the Working Group Environment initiated this third INTERREG programme in the region and is in charge of the work validation, while the action programmes INTERREG PAMINA and Upper Rhine Centre South are responsible for the FEDER funds management. In the frame of this third INTERREG project named Atmo-rhenA, three regions are working together towards a ‘‘common assessment and information system on air quality in the Upper Rhine Valley’’: the BadenLand and the South-Palatinate in Germany, the two cantons of Basel in Switzerland and the Alsace region in France. The project started in 2001 and will be completed at the end of 2006. The financial partners represent 3 Mh, with about the half of the funds coming from the three air quality networks, one-third being FEDER funds and complementary funds coming from the Alsace Region and from the French Government Agency for Environment and Energy Management (ADEME).
2. The third INTERREG programme on air quality in the Upper Rhine Valley 2.1. Common air quality measurements web page
The first part of the programme was headed by the LUBW, and its aim was to set up a common and permanent information on air quality in the Upper Rhine Valley: daily and long-term cartographic information on air quality measurements, daily diffusion of common air quality indexes with trend forecast for the next day and special communications in case of
A Common Air Quality Modelling System in the Upper Rhine Valley
111
particulate matter (PM) pollution episodes particularly in winter or ozone (O3) pollution episodes particularly in summer. To meet these objectives a bilingual website was designed and is available since June 2005 on http://www.atmo-rhinsuperieur.net (in French) or http://www.luft-am-oberrhein.net (in German). 2.2. Transboundary emission inventory and its gridding
In the frame of the second part of the programme, piloted by the ASPA, a transboundary communal and annual emission inventory was realised and gridded into a kilometre and hourly cadaster. Primary data on emissions activities and factors for the French part, and on emissions for the German and Swiss parts were gathered. Then the EMISS’AIR software tool was designed at the ASPA to compute the transboundary inventory by integrating emissions of the three parts into a common database: surfacic, linear and ponctual sources are considered, with 40 pollutants, 10 sectors, 50 sub-sectors and different fuels. MANAGAIR was created at the ASPA to grid the inventory using a geographic information system (GIS) and a detailed land use, to introduce a detailed PM (Pregger et al., 2004) and NMVOC (Sambat et al., 2004) speciation of IER and CITEPA, and to give an hourly distribution of emissions for each sector, under-sector and day type (week, Saturday, Sunday). The sides of the domain are completed with EMEP data (Fig. 1).
Figure 1. From transboundary primary data on emission to a gridded and hourly distributed emission cadastre as air quality models input.
112
R. Deprost et al.
The cadaster is used as input in the CHIMERE CTM. This tool can be used for any domain or spatial resolution and allows the preparation of emission scenarios by cutting or reducing emissions of chosen activity sectors. 2.3. Transboundary air quality modelling platform
In the third and last part of this INTERREG programme, headed by the ASPA, a regional deterministic modelling platform has been set up and is used for daily air quality forecasts as well as for studies like determination of local and regional pollution influence, biogenic and anthropic emissions influence or simulation of emission reduction scenarios. 3. Description of the modelling system
For the study of a domain like the Upper Rhine Valley, 3-dimensions deterministic meteorological and CTMs are necessary. Indeed it combines most of the key factors in air pollution: urban areas, roads and motorways, strong industrial areas with refineries, petrochemistry, power plants and a complex regional meteorology due to the topography with the Vosges Mountains in the West and the Black Forest in the East. There are also strong biogenic emissions over the extended areas of grass, forest and farming in the valley. Moreover, the CHIMERE CTM is now known for its good performances as predicting tool both for short-term forecasts and for the assessment of long-term emission abatement strategies. For the meteorology, the MM5 model is used with a 12 by 12 km resolution over the ‘‘Central Europe’’ mother domain and with a 4 by 4 km resolution over the ‘‘Upper Rhine Valley’’ domain nudged in the first one. MM5 runs with 25 pressure sigma-levels from surface to 100 hPa, and is forced at the lateral boundaries by GFS 6-hourly analyses or forecasts (NCEP). Its output fields are provided to the CHIMERE CTM (Vautard et al., 2004). The CHIMERE CTM is used over a 4 by 4 km resolution grid, with 48 cells in longitude and 64 in latitude (Fig. 2). It is used with 8 vertical pressure layers (vertical coordinate being terrain-following), going from surface to 500 hPa, so it encloses the boundary layer. The CTM is nested within European PREVAIR (http://www.prevair.org) analyses and/ or forecasts according to the scenario or forecast mode of the simulation. 4. Assessment and validation of the modelling system
The regional modelling system reliability assessment was based on the comparison of simulations with the observations of the transboundary
A Common Air Quality Modelling System in the Upper Rhine Valley
113
Figure 2. Grid of the CHIMERE chemistry-transport model (CTM) and topography of the Upper Rhine Valley.
measurement campaign that took place in the Upper Rhine Valley in 2003, from the 19th of May to the 16th of June. For this validation part a cooperation took place with the LPAS of the EPFL, which studied the field campaign with the deterministic models METHPOMOD and FVM/ TAPOM, identified the ozone regimes of the valley and the parts of the
114
R. Deprost et al.
domain where regional pollution phenomena are predominant, which means that local actions on emissions can have a real impact on pollution episodes.
4.1. Transboundary measurement campaign
Near the fixed measurement networks (ASPA, LUBW, LHA and METEO FRANCE), there were 12 laboratory trucks of air quality networks participating in the campaign. There were 17 French, German, Swiss and Italian research teams working in 3 specific measurement sites. The measurement campaign began with an intercomparison of measurement devices. The two intensive observation periods (IOPs) were from the 3rd to the 5th and from the 10th to the 12th of June 2003. The measured chemical fields were O3, NO, NO2, NOx, NOy, SO2, CO, CO2, PM10, PM2.5, COV, NMVOC, HONO, HCHO, H2O2, HNO3, MHP, HMHP, etc. For the meteorology, only variables in direct interaction with photochemistry (wind field, pressure, nebulosity, radiation, mixing height, humidity, temperature, precipitations y) have been measured. In 2004, the whole data were made available to all participants on a server, where they can extract data by FTP for their own studies (a workshop with presentation of the results took place in January 2006 in Strasbourg). NETCDF observations files have been built and have been used to compare measurements directly with simulated fields.
4.2. Validation of the modelling system
The main results are that MM5 reproduces well the temperature fields and accounts properly for heat storage in the urban canopy during summertime, especially in bigger cities. However, there is a small underestimation of temperatures during the night over the whole domain. The relative humidity is well reproduced. Horizontal wind fields are also very well reproduced (Fig. 3), and the model also produces diurnal mountain and valley breezes on the sides of the valley (positive vertical wind during the day and negative vertical wind during the night). CHIMERE accounts properly for the ozone concentrations in the first and in other layers of the model (Fig. 4). The NOx are well reproduced by the model, showing the good quality of the temporal profiles of the emission cadaster.
A Common Air Quality Modelling System in the Upper Rhine Valley
115
Figure 3. Horizontal wind direction in degrees during the first IOP, measured (gray) and modelled (black).
5. Transboundary daily air quality forecasts
Daily air quality forecasts for the Upper Rhine Valley are operational since January 2005. The skill of the whole system in simulating and forecasting ozone and aerosols at the ground level is quantified with classical statistical parameters (mean bias and Root Mean Square Error, RMSE) using the routine measurements (Table 1). In June 2005, the performances of the model in forecasting the ozone maxima of the day were pretty good compared to other known modelling systems.
R. Deprost et al.
116
Figure 4. Measured (gray) and modelled (black) ozone concentrations during the first IOP in mg m 3 for three station types: urban (left), suburban (middle) and rural (right). Table 1. Statistical indicators on the forecasts skill of the modelling system for O3 in summer 2005 (daily maxima, only French stations) Station type/ term (mg m 3)
Urban Suburban Rural Traffic
D 1
D
D+1
D+2
Mean Bias
RMSE
Mean Bias
RMSE
Mean Bias
RMSE
Mean Bias
RMSE
15 9 8 15
25 20 19 25
14 7 7 14
24 21 20 24
11 5 5 11
24 21 20 24
12 6 6 12
24 22 21 24
The regional modelling system provides daily boundary conditions to URBAN’AIR, an urban deterministic platform with a few hundred meters resolution used at the ASPA to get daily air quality forecasts over the city of Strasbourg (Fig. 5). 6. Origin of ozone plumes in the Upper Rhine Valley
For the last day of the first IOP, the model gives ozone concentration maxima up to 160 mg m 3 in the plume of Strasbourg. Like anthropic
A Common Air Quality Modelling System in the Upper Rhine Valley
117
Figure 5. PM10 forecasts for the 01/02/2006 by urban modelling system URBA’NAIR (www.atmo-alsace.net).
Figure 6. For the typical summer days studied the influence of boundary conditions (light gray) and of local biogenic (middle gray) and anthropic (dark gray) emissions was like represented on the left for ozone on the edges of the valley including Vosges and Black Forest (left), in the valley (middle) and in the plume (right).
emissions, the calculation of biogenic emissions by the modelling system has been updated and adapted to the tree and forest distribution of the Upper Rhine Valley. It is possible to suppress all local emissions in the model, which allows to assess the contribution of chemical boundary conditions to the local ozone plume. The same work can be done for local biogenic emissions alone (Fig. 6).
118
R. Deprost et al.
7. Ozone regimes in the Upper Rhine Valley
Ozone isopleths show the non-linearity of ozone concentrations towards anthropic NMVOC and NOx emissions (Couach, 2003). Some examples of ozone isopleths are shown in Fig. 7: for the 11th of June 2003, Mannheim Centre (urban area) is clearly VOC limited, whereas Strasbourg Ouest (suburban area) is rather NOx limited and Schwarzwald Sud (rural area) is clearly NOx limited. Other methods have been investigated to determine ozone regimes in the Upper Rhine Valley. Maps of ozone concentrations differences obtained with same reductions of anthropic NMVOC and NOx have shown strong VOC limited regimes in urban areas and very lightly NOx limited regimes in suburban and rural areas (Clappier et al., 2005). The Sillman indicator H2O2/HNO3 has also been determined, it was generally between
Figure 7. Ozone isopleths in mg m 3 for the 11th of June 2003 for Mannheim Centre, Strasbourg Ouest and Schwarzwald Sud.
A Common Air Quality Modelling System in the Upper Rhine Valley
119
0.1 and 0.2 and its cartography did not always give the same results as the emission reduction scenarios.
8. Emission reduction scenarios studies
Several short-term local emission reductions like emergency measures as well as long-term European emission scenarios have been tested. Longterm evolutions are taken from the CAFE propositions. The differences between the following emissions and the EMEP 2000 base case are
Figure 8. Decrease of the number of threshold exceedance hours (gray squares) with the application of the 2020 CLE scenario on the 12th of June 2003. Former and new geographic zone of threshold exceedance in gray and black lines.
R. Deprost et al.
120
applied to the local transboundary emission inventory: 2020 Current Legislation Europe (CLE), 2020 Low, Medium and High Scenarios Ambitions, and 2020 MTFR scenario (CAFE). The figure shows one of the examples of the result: the application of the CLE scenario to boundary conditions and to local emissions on the 12th of June 2003. During this day an ozone threshold exceedance was observed and reproduced by the model in the base case. With the application of the scenario, an exceedance is still observed but the geographic area is restricted and the number of hours of threshold exceedance decreases for 60% of the population in the Upper Rhine Valley (Fig. 8). 9. Conclusion and perspectives
The MM5 and CHIMERE modelling system simulates the meteorological and chemical parameters with a sufficient skill to allow its use for operational air quality forecasts, and for the studies performed in the frame of the INTERREG programme in the Upper Rhine Valley in 2006. For instance it allows to assess the efficiency of local short-term emission reduction like emergency measures or European long-term scenarios like those elaborated in the CAFE programme. Discussion
P. Builtjes:
R. Deprost:
In case of exceedances of limit values of NO2 and/or PM10/2.5, is there the effort to have similar abatement strategies across the borders of the three countries? The cross-border cooperation in the Upper Rhine Valley as regards air quality is essentially present within the Upper Rhine Conference. This intergovernmental institution gives the ‘‘environment’’ working group the mandate to launch projects that are then developed within the ‘‘air quality’’ experts group. The ‘‘air quality’’ experts group is linked with the ‘‘environment’’ working group. The mandate that led to achieve the INTERREG III project presented in Leipzig, was financed by the European Union and included the common broadcast of information and the setting of a modelling. As regards the long-term policy, the setting of common cross-border strategies of pollutant emission reduction in order to reduce the continuous background pollution has
A Common Air Quality Modelling System in the Upper Rhine Valley
121
been dealt within the frame of an INTERREG I project concerning the creation of a cross-border air protection plan for Strasbourg/Ortenau (approved on the 8th of December 1995). Taking into account the regulatory abilities of the Rhine’s both sides, this plan just resulted in combining two different catalogues of measures: one for the Communaute´ Urbaine de Strasbourg and the other for the Ortenau Kreise including three cross-border topics about (I) the proposal of a cross-border tariff union for public transports (including rail), (II) to check whether it is possible for the city of Kehl to join the public transport network of Strasbourg and (III) the creation of another common cycle track. As a consequence, the matter of the long-term common measures has only been orally mentioned during one or the other meeting, just as a possible topic of an INTERREG IV project in the Upper Rhine region for example. The experts know how necessary it is to conclude first the different preliminary reviews. The organised exchange on the air quality protection plans represented a part of it. The INTERREG III conclusions are in progress (end 2006) and will represent another part, especially with the air quality simulation for 2020 from more or less controlled scenarios. Concerning the setting of short-term emergency measures when ozone peaks appear, the Upper Rhine Conference asked the question of the available means set up by the different authorities in the Upper Rhine region after the heat wave in 2003 in order to restrict pollution peaks and their effects. A progressive working programme was chosen: (I) to identify the short-term measures set up for each of the three countries, (II) to analyse the coordination possibilities of the measures and (III) to define the effectiveness of their setting. In order to deepen the first topic mentioned the ‘‘air quality’’ experts group received another term of reference. A report on the first topic is in progress at the moment. On the other side, the chairman of the Communaute´ Urbaine de Strasbourg also asked all the Upper Rhine communities after the heat wave of 2003 for a study to know whether it is possible to reduce the common emissions that are under their responsibilities. The
R. Deprost et al.
122
working group dealing with this question applied to the ‘‘air quality’’ experts group to define the feasibility, which is done within the frame of the INTERREG III project. One of the topic difficulties consists in the difference between French (regulatory emergency measures that have to be set up within the frame of the Air Act and the European Ozone Directive) and German (emergency measures do not have a significant effect for possible emission reduction) policies.
ACKNOWLEDGMENTS
We are thankful to NCAR, IPSL, NCEP and INERIS for the daily use of the MM5 and CHIMERE models, and of the GFS and PREVAIR systems outputs. REFERENCES Clappier, A., Couach, O., Kirchner, F., 2005. Simulations des Pe´riodes d’Observation Intensives et de diffe´rents sce´narios de re´duction d’e´missions, Rapport Final, LPAS – Laboratoire De Pollution Atmosphe´rique et Sol, EPFL Ecole Polytechnique Fe´de´rale de Lausanne. Couach, O., 2003. Eude et mode´lisation de la pollution photochimique dans l’espace du Rhin Supe´rieur-Analyse des re´gimes de production d’ozone-Elaboration de sce´narios de re´ductions des e´missions, Syste`me commun d’e´valuation et d’information sur la qualite´ de l’air dans l’espace du Rhin Supe´rieur, Projet INTERREG III, Theme3 (E23.1-8A). Pregger, T., Sambat, S., Friedrich, R., 2004. Study on particulate matter emissions: Particle size distribution and chemical composition, IER—Institut fu¨r Energiewirtschaft und Rationelle Energieanwendung, Universita¨t Stuttgart, CITEPA—Centre Interprofessionnel Technique d’Etudes de la Pollution Atmosphe´rique, November 2004. Sambat, S., Theloke, J., Friedrich, R., Allemand, N., 2004. Bibliographic study concerning the speciation of NMVOC, IER—Institut fu¨r Energiewirtschaft und Rationelle Energie-anwendung, Universita¨t Stuttgart, CITEPA—Centre Interprofessionnel Technique d’Etudes de la Pollution Atmosphe´rique, November 2004. Vautard, R., Beekmann, M., Bessagnet, B., Blond, N., Hodzic, A., Honore´, C., Malherbe, L., Menut, L., Rouil, L., Roux, J., 2004. The use of MM5 for operational ozone/ NOx/aerosols prediction in Europe: strengths and weaknesses of MM5, Institut Pierre-Simon Laplace, CNRS, Paris, France, INERIS, Verneuil en Halatte, France, Laboratoire interuniversitaire des Syste`mes Atmosphe´riques, CNRS, Cre´teil, France.
Developments in Environmental Science, Volume 6 C. Borrego and E. Renner (Editors) Copyright r 2007 Elsevier Ltd. All rights reserved. ISSN: 1474-8177/DOI:10.1016/S1474-8177(07)06025-1
123
Chapter 2.5 Perturbational downscaling and its applications in air pollution and meteorological problems Eugene Genikhovich and Guy Schayes Abstract A widely used approach to reduction of the downscaling errors was suggested by Davis and based on the brute-force dumping of distortions of the numerical solution in a ‘‘strip’’ of the sub-domain adjacent to the boundary. It produces noticeable unphysical effects, especially in the near-boundary strip, so that the applicability of the whole numerical solution looks questionable. An alternative approach is based on the reformulation of the governing equations in the perturbation form. The governing equations derived for this perturbation are to be solved on the fine grid mesh to generate, as a result, the downscaled fields, reducing considerably the interference between coarse and fine grid solutions. In this paper, the efficiency of such an approach is demonstrated not only on model examples but also on mesometeorological applications using the non-hydrostatic Thermal Vorticity Mesoscale (TVM) model which solves the dynamic equations using the transformation into the vorticity. Also, by construction, this approach automatically satisfies the continuity equation that is of utmost importance when the computed wind fields are used to drive the models of the atmospheric transport and dispersion of tracers. 1. Introduction
Numerous applications require more detailed description of meteorological fields than allowed by ‘‘standard’’ Numerical Weather Prediction (NWP) models. These applications, which vary from regional and local weather forecasting and nowcasting to dispersion modelling and applied climatology, usually exploit the approach known as nesting. One-way nesting (referred also as downscaling) procedures are aimed to increase the resolution of the NWP model inside a certain sub-domain of the
Eugene Genikhovich and Guy Schayes
124
computational domain; in two-way nesting procedures, the detailed solution obtained in this sub-domain is used to correct meteorological fields in the rest of the domain under consideration. Other techniques are also used to increase the resolution of NWP models (e.g., multiscale grids). In this paper, however, our focus is only on downscaling (i.e., one-way nesting) based on solution of dynamic equations. In a usual downscaling procedure, the data from the coarse grid, being used to determine initial and boundary conditions in a sub-domain of interest, drive a solution in this sub-domain on a finer grid mesh. As simple as this idea is, its practical implementation is complicated because these initial and boundary conditions are obtained by a kind of interpolation from the coarse grid to the fine one. The main problem that arises here is that these interpolated initial and boundary conditions are, generally speaking, incompatible with the governing equations though the fields on the coarse grid were obtained as a solution of those equations. In order to demonstrate the nature of this problem, let us consider the simplest case of the linear equation @u ¼ Lu þ f ; @t
ujt¼t0 ¼ u0 ;
ujz¼zs ¼ g;
ujG ¼ uG
(1)
where z ¼ zs corresponds to the underlying surface, G denotes other boundaries of the computational domain D; u0, f and g are given functions. For the sake of simplicity, it is assumed here that the only goal of downscaling is to improve the resolution of the numerical solution in a sub-domain S of the computational domain. To justify the need for downscaling, let us assume that the part g of the underlying surface in S is more inhomogeneous than in the rest of the computational domain D. In order to visualize L, one can assume, for example, that L is the advectiondiffusion operator, i.e., L ¼ (@i(Kij@j)Ui@il), where @i means the partial derivative along the xi axis (x3 z corresponds to the vertical direction); Ui and Kij are components of the wind velocity and the eddy-diffusivity tensor; l is inversely proportional to the half-life time scale of the pollutant considered; and the Einstein rule of summation from 1 to 3 over repeated indexes is implied (in this case u is the concentration of the pollutant). As a result of the numerical solution of Eq. (1) in the domain D with characteristic resolution h, one can obtain a grid function that is defined only at the grid points. Let us denote as uh the ‘‘smooth’’ function defined at all points of the computation domain that is a ‘‘continuator’’ of this
Perturbational Downscaling and Its Applications
125
grid function. Then, uh should satisfy the following equation: @uh ¼ Luh þ f þ h ; uh jt¼t0 ¼ u0h ; uh jz¼zs ¼ gh ; uh jG ¼ uGh (2) @t where u0h and uGh denote continuators of uh at the initial time and at the boundary, respectively, and gh denotes the continuator of the grid function with resolution h, which corresponds to g. Actually, Eq. (2) could be considered as a definition of the term eh, which results from the errors of discretization, numerical solution, etc., and, if the numerical scheme is ‘‘efficient’’, should, generally speaking, tend to zero when h tends to zero. Let us assume first that one has obtained in the domain D the numerical solution corresponding to the resolution h ¼ h1, which is not sufficient to resolve the small-scale features of g in S but reproduces this function fairly well at all other points of the underlying surface. Then downscaling means that, starting at the moment of time t ¼ t0, one should calculate in the sub-domain S the solution sought with the resolution h ¼ h2oh1. It means that, using uh1 ; one should reconstruct the values of uh2 jt¼t0 in S, and on its boundary, Gs, the next step being to solve the corresponding equation with reconstructed initial and boundary conditions. Let us denote these results of reconstruction as uh2 ðh1 Þjt¼t0 and uGh2 ðh1 Þ; similarly, the notation gh2 ðh1 Þ is used here but, in fact, for the sake of simplicity it is assumed further that gh2 ðh1 Þ ¼ gh2 : Thus, the ‘‘standard’’ downscaling procedure is based on solution of the following problem: @v ¼ Lv þ f þ h2 ; vjt¼t1 ¼ uh2 ðh1 Þjt¼t0 ; vjz¼zsjg ¼ gh2 ðh1 Þ; vjGs ¼ uGh2 ðh1 Þ (3) @t
where z ¼ zs|g indicates the points of the underlying surface located in S. In fact, however, the ‘‘exact’’ (global) numerical solution w with resolution h2, which is supposed to be reproduced with the downscaling procedure, should satisfy in S the following equation: @w ¼ Lw þ f þ h2 ; wjt¼t0 ¼ uh2 jt¼t1 ; wjz¼zsjg ¼ gh2 ; wjGs ¼ uGh2 (4) @t Subtracting Eq. (4) from Eq. (3), one could find the equation describing the error d ¼ vw of the standard downscaling procedure @d ¼ Ld; djt¼t0 ¼ uh2 ðh1 Þ uh2 ; djz¼zsjg ¼ gh2 ðh1 Þ gh2 ; djGs ¼ uGh2 ðh1 Þ ujGh2 (5) @t
For the sake of simplicity, one can assume here that d|z ¼ zs ¼ 0 (actually, it is not always true, especially, if the conditions at the underlying surface include the fluxes of the substances of interest). Now it is
126
Eugene Genikhovich and Guy Schayes
obvious that the standard downscaling procedure has an inherent drawback because its result is visibly influenced by the propagation of the errors of the coarse-grid solution, represented in the initial and boundary conditions of Eq. (5), into the downscaling domain. Because h1 is assumed to be larger than h2, one can expect that the errors of the coarsegrid (‘‘outer’’) problem should dominate in forming the error d. Usually Eq. (5) describes the attenuation of the influence of errors in initial and boundary conditions with time and distance from the boundaries. It seems to be not the best idea, however, to impose the ‘‘task of reduction’’ of the errors of the ‘‘outer’’ problem on the solution of the fine grid (‘‘inner’’) problem, in particular, because of influence on these errors of ‘‘outer’’ initial and boundary conditions that are not reproduced directly in the downscaled sub-domain. One can see from Eq. (5) that the major source of the error in downscaling is due to the interpolation of the computed fields from the coarse grid into the finer one. As a possible way to reduce its influence, Davies (1976) and Miyakoda and Rosati (1977) suggested the use of numerical procedures of damping of corresponding errors inside a strip of grid cells located near the boundaries of the downscaled sub-domain. Indeed, if certain mathematical restrictions are satisfied in the problem (Eq. (1)), one could expect that the initial perturbations due to the erroneous initial conditions should decrease in time and that the perturbations due to the erroneous boundary conditions should decrease with the distance from the boundary. The brute-force damping suggested by Davies and Miyakoda and Rosati should evidently speed up these processes. Still, such an approach does not look logical enough because one first introduces the errors in the initial and boundary conditions and then tries to suppress these errors. Moreover, the dumping procedure actually results in decoupling of the inner and outer solutions and, when applied to NWP problems, in non-physical effects reproduced in the grid cells corresponding to the above mentioned strip. In this paper, we discuss a different approach to reduction of the errors of downscaling which is based on the ideas of the perturbation theory (e.g., Nayfeh, 1973).
2. General formalism of the perturbational downscaling
The general idea of the proposed approach is to eliminate the terms uh2 ðh1 Þjt¼t0 ; uGh2 ðh1 Þ and, possibly, gh2 ðh1 Þ ¼ gh2 from the initial and boundary conditions for the downscaling domain. The corresponding technique has been widely used in perturbation methods. It is based on decomposition of the problem, which is characterized by the presence of
Perturbational Downscaling and Its Applications
127
two significantly different length scales. A typical example of such a problem (the Blasius problem) is dealing with the formation of the thin boundary layer above the flat plate placed in the free large-scale viscous flow. In this case, the perturbation method recommends decomposing the problem into two successive ones. The solution of the first (‘‘outer’’) problem describes the large-scale outer flow with no account for the viscosity effects near the surface of the plate; the second (‘‘inner’’) one describes the effects of friction in a smaller domain adjacent to the plate surface using the solution of the first problem to derive the boundary conditions for the second one. One of the principal features of the perturbation method is that one should not correct the