Introduction to Health and Safety at Work, Third Edition: The Handbook for the NEBOSH National General Certificate

Introduction to Health and Safety at Work This page intentionally left blank Introduction to Health and Safety at W...

Author: Phil Hughes | Ed Ferrett

298 downloads 2352 Views 13MB Size Report

This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!

Report copyright / DMCA form

DOWNLOAD PDF

Introduction to Health and Safety at Work

This page intentionally left blank

Introduction to Health and Safety at Work Third edition The handbook for students on NEBOSH and other introductory H&S courses Phil Hughes MBE, MSc, FIOSH, RSP, Chairman NEBOSH 1995–2001 Ed Ferrett PhD, BSc, (Hons Eng), CEng, MIMechE, MlEE, MI0SH, Deputy Chairman NEBOSH

AMSTERDAM • BOSTON • HEIDELBERG • LONDON • NEW YORK • OXFORD PARIS • SAN DIEGO • SAN FRANCISCO • SINGAPORE • SYDNEY • TOKYO Butterworth–Heinemann is an imprint of Elsevier

Butterworth-Heinemann is an imprint of Elsevier Linacre House, Jordan Hill, Oxford OX2 8DP 30 Corporate Road, Burlington, MA 01803 First edition 2003 Reprinted 2003 (twice) Second edition 2005 Reprinted 2006 Third edition 2007 Copyright © 2005, 2007, Phil Hughes and Ed Ferrett. Published by Elsevier Limited. All rights reserved The right of Phil Hughes and Ed Ferrett to be identiﬁed as the authors of this work has been asserted in accordance with the Copyright, Designs and Patents Act 1988 No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher Permission may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone (44) (0) 1865 843830; fax (44) (0) 1865 853333; email: [email protected]. Alternatively you can submit your request online by visiting the Elsevier web site at http://elsevier.com/locate/permissions, and selecting Obtaining permission to use Elsevier material Notice No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein. Because of rapid advances in the medical sciences, in particular, independent veriﬁcation of diagnoses and drug dosages should be made British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library Library of Congress Cataloguing in Publication Data A catalogue record for this book is available from the Library of Congress ISBN 978-0-7506-8503-0 For information on all Butterworth-Heinemann publications visit our web site at www.books.elsevier.com Typeset by Charon Tec Ltd (A Macmillan Company) Printed and bound in Slovenia 07 08 09 10 11

10 9 8 7 6 5 4 3 2 1

Contents PREFACE TO THE THIRD EDITION ACKNOWLEDGEMENTS ABOUT THE AUTHORS LIST OF PRINCIPAL ABBREVIATIONS ILLUSTRATIONS CREDITS 1

HEALTH AND SAFETY FOUNDATIONS 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12 1.13 1.14 1.15 1.16 1.17

2

1

Introduction Some basic deﬁnitions The legal framework for health and safety The legal system in England and Wales The legal system in Scotland European Courts Sources of law (England and Wales) Common law torts and duties Levels of statutory duty The inﬂuence of the European Union (EU) on health and safety The Health and Safety at Work Act 1974 The Management of Health and Safety at Work Regulations 1999 Role and function of external agencies Sources of information on health and safety Moral, legal and ﬁnancial arguments for health and safety management The framework for health and safety management Practice NEBOSH questions for Chapter 1

1 1 3 4 5 5 5 6 7 8 9 14 14 15 16 19 21

POLICY 2.1 2.2 2.3 2.4 2.5

3

xi xiii xv xvi xviii

23

Introduction Legal requirements Key elements of a health and safety policy Review of health and safety policy Practice NEBOSH questions for Chapter 2 Appendix 2.1 – Health and Safety Policy Checklist

23 23 24 26 27 29

ORGANIZING FOR HEALTH AND SAFETY

31

3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10

31 31 32 32 32 33 35 35 36 38

Introduction Control Employers’ responsibilities Employees’ responsibilities Organizational health and safety responsibilities Role and functions of health and safety and other advisers Persons in control of premises Self-employed The supply chain Contractors

v

Contents 3.11 3.12 3.13

4

5

6

Joint occupation of premises Cooperation with the workforce Practice NEBOSH questions for Chapter 3 Appendix 3.1 – Typical organizational responsibilities Appendix 3.2 – Checklist for supply chain health and safety management

PROMOTING A POSITIVE HEALTH AND SAFETY CULTURE

49

4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 4.9 4.10 4.11

49 49 50 51 56 58 60 60 62 63 65

Introduction Deﬁnition of a health and safety culture Safety culture and safety performance Human factors and their inﬂuence on safety performance Human errors and violations The development of a positive health and safety culture Effective communication Health and safety training Internal inﬂuences External inﬂuences Practice NEBOSH questions for Chapter 4

RISK ASSESSMENT

67

5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11

67 67 68 68 70 70 70 70 71 73 75 77 78

Introduction Legal aspects of risk assessment Forms of risk assessment Some deﬁnitions The objectives of risk assessment Accident categories Health risks The management of risk assessment The risk assessment process Special cases Practice NEBOSH questions for Chapter 5 Appendix 5.1 – Hazard checklist Appendix 5.2 – Example of a risk assessment record

PRINCIPLES OF CONTROL 6.1 Introduction 6.2 Principles of prevention 6.3 Hierarchy of risk control 6.4 Controlling health risks 6.5 Safe systems of work 6.6 Lone workers 6.7 Permits to work 6.8 Emergency procedures 6.9 First aid at work 6.10 Practice NEBOSH questions for Chapter 6 Appendix 6.1 – Fire notice Appendix 6.2 – Job safety analysis form Appendix 6.3 – Essential elements of a permit-to-work form

7

MONITORING, REVIEW AND AUDIT 7.1 7.2 7.3

vi

42 42 43 45 47

Introduction The traditional approach to measuring health and safety performance Why measure performance?

80 80 80 81 84 86 89 89 92 94 97 99 100 101

102 102 102 103

Contents 7.4 7.5 7.6 7.7 7.8 7.9 7.10 7.11

What to measure Measuring failure – reactive monitoring Active monitoring – how to measure performance Who should monitor performance? Frequency of monitoring and inspections Report writing Review and audit Practice NEBOSH questions for Chapter 7 Appendix 7.1 – Workplace inspection exercises Appendix 7.2 – Basic checklist of items to be covered in an area inspection

8 INCIDENT AND ACCIDENT INVESTIGATION AND REPORTING 8.1 8.2 8.3 8.4 8.5 8.6 8.7 8.8

Introduction Reasons for incident/accident investigation Which incidents/accidents should be investigated? Investigations and causes of incidents Legal recording and reporting requirements Internal systems for collecting and analysing incident data Compensation and insurance issues Practice NEBOSH questions for Chapter 8 Appendix 8.1 – Injury report form Appendix 8.2 – Information for insurance/compensation claims

9 MOVEMENT OF PEOPLE AND VEHICLES – HAZARDS AND CONTROL 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8

Introduction Hazards to pedestrians Control strategies for pedestrian hazards Hazards in vehicle operations Control strategies for safe vehicle operations The management of vehicle movements Managing occupational road safety Practice NEBOSH questions for Chapter 9

10 MANUAL AND MECHANICAL HANDLING HAZARDS AND CONTROL 10.1 10.2 10.3 10.4 10.5 10.6 10.7

Introduction Manual handling hazards and injuries Manual handling risk assessments Safety in the use of lifting and moving equipment Types of mechanical handling and lifting equipment Requirements for the statutory examination of lifting equipment Practice NEBOSH questions for Chapter 10 Appendix 10.1 – Manual handling of load assessment checklist

11 WORK EQUIPMENT HAZARDS AND CONTROL 11.1 11.2 11.3 11.4 11.5 11.6 11.7 11.8 11.9

Introduction Suitability of work equipment and CE marking Use and maintenance of equipment with specific risks Information, instruction and training Maintenance and inspection Operation and working environment User responsibilities Hand-held tools Mechanical machinery hazards

104 105 105 107 107 107 109 111 112 114

116 116 117 118 118 121 123 124 125 126 128

130 130 130 132 135 136 137 137 141

143 143 143 144 148 149 154 155 156

159 159 159 161 161 162 163 164 164 167

vii

Contents 11.10 11.11 11.12 11.13 11.14 11.15 11.16 11.17

Mobile work equipment Non-mechanical machinery hazards Examples of machinery hazards Practical safeguards Other safety devices Application of safeguards to the range of machines Guard construction Practice NEBOSH questions for Chapter 11

12 ELECTRICAL HAZARDS AND CONTROL 12.1 12.2 12.3 12.4 12.5 12.6 12.7 12.8

Introduction Principles of electricity and some deﬁnitions Electrical hazards and injuries General control measures for electrical hazards The selection and suitability of equipment Inspection and maintenance strategies Portable electrical appliances testing Practice NEBOSH questions for Chapter 12

13 FIRE HAZARDS AND CONTROL 13.1 13.2 13.3 13.4 13.5 13.6 13.7 13.8 13.9 13.10 13.11 13.12 13.13 13.14 13.15 13.16 13.17

Introduction The Regulatory Reform (Fire Safety) Order 2004 (RRFSO) – Requirements Basic principles of ﬁre Methods of extinction Classiﬁcation of ﬁre Principles of heat transmission and ﬁre spread Common causes of ﬁre and consequences Fire risk assessment Dangerous substances Fire detection and warning Means of escape in case of ﬁre Principles of ﬁre protection in buildings Provision of ﬁre-ﬁghting equipment Maintenance and testing of ﬁre-ﬁghting equipment Planning for an emergency and training staff Fire procedures and people with a disability Practice NEBOSH questions for Chapter 13

14 CHEMICAL AND BIOLOGICAL HEALTH HAZARDS AND CONTROL 14.1 14.2 14.3 14.4 14.5 14.6 14.7 14.8 14.9 14.10 14.11 14.12 14.13 14.14 14.15

viii

Introduction Forms of chemical agent Forms of biological agent Classiﬁcation of hazardous substances and their associated health risks Routes of entry to the human body Health hazards of speciﬁc agents Requirements of the COSHH Regulations Details of a COSHH assessment The control measures required under the COSHH Regulations Health surveillance and personal hygiene Maintenance and emergency controls The transport of hazardous substances by road An illustrative example using COSHH controls Environmental considerations Practice NEBOSH questions for Chapter 14

169 171 171 173 176 177 185 185

187 187 187 189 194 195 197 197 200

201 201 202 204 206 206 206 208 209 212 214 215 217 219 220 220 220 221

223 223 223 224 224 225 228 232 232 236 242 243 243 244 244 246

Contents 15 PHYSICAL AND PSYCHOLOGICAL HEALTH HAZARDS AND CONTROL 15.1 15.2 15.3 15.4 15.5 15.6 15.7 15.8 15.9

Introduction Task and workstation design Welfare and work environment issues Noise Heat and radiation hazards The causes and prevention of workplace stress Causes and prevention of workplace violence The effects of alcohol and drugs Practice NEBOSH questions for Chapter 15 Appendix 15.1 – Smokefree workplace

16 CONSTRUCTION ACTIVITIES – HAZARDS AND CONTROL 16.1 16.2 16.3 16.4 16.5 16.6 16.7

Introduction The scope of construction Construction hazards and controls The management of construction activities Working above ground level or where there is a risk of falling Excavations Practice NEBOSH questions for Chapter 16 Appendix 16.1 – Inspection report Appendix 16.2 – Summary of proposed application and notiﬁcation under CDM 2007 Appendix 16.3 – Pre-Construction information Appendix 16.4 – Construction Phase Plan

17 SUMMARY OF THE MAIN LEGAL REQUIREMENTS 17.1 17.2 17.3 17.4 17.5 17.6 17.7 17.8 17.9 17.10 17.11 17.12 17.13 17.14 17.15 17.16 17.17 17.18 17.19 17.20 17.21 17.22 17.23 17.24 17.25 17.26 17.27

Introduction The legal framework List of Acts, Order and Regulations summarized Health and Safety at Work etc. Act (HSW Act) 1974 Environmental Protection Act 1990 Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 and 2005 amendment Regulations Conﬁned Spaces Regulations 1997 Construction (Design and Management) (CDM) Regulations 2007 Construction (Head Protection) Regulations 1989 Health and Safety (Consultation with Employees) Regulations 1996 Control of Substances Hazardous to Health Regulations (COSHH) 2002 and 2005 Amendment Dangerous Substances and Explosive Atmospheres Regulations (DSEAR) 2002 Health and Safety (Display Screen Equipment) Regulations 1992 Electricity at Work Regulations 1989 Employers’ Liability (Compulsory Insurance) Act 1969 and Regulations 1998 Regulatory Reform (Fire Safety) Order 2005 Health and Safety (First aid) Regulations 1981 Health and Safety (Information for Employees) Regulations 1989 Hazardous Waste (England and Wales) Regulations 2005 Ionising Radiations Regulations 1999 Lifting Operations and Lifting Equipment Regulations 1998 as amended in 2002 Management of Health and Safety at Work Regulations 1999 as amended in 2003 Manual Handling Operations Regulations (MHO) 1992 as amended in 2002 Control of Noise at Work Regulations 2005 Personal Protective Equipment at Work Regulations 1992 as amended in 2002 Provision and Use of Work Equipment Regulations 1998 (except part IV) as amended in 2002 The Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995

250 250 250 258 259 265 269 270 273 274 277

278 278 278 279 285 291 297 298 300 303 304 305

307 307 307 308 309 312 320 324 326 337 338 339 342 345 347 349 351 358 358 359 360 362 365 367 369 374 376 380

ix

Contents 17.28 17.29 17.30 17.31 17.32 17.33 17.34

Safety Representatives and Safety Committees Regulations 1977 Health and Safety (Safety Signs and Signals) Regulations 1996 Supply of Machinery (Safety) Regulations 1992 Control of Vibration at Work Regulations 2005 Workplace (Health, Safety and Welfare) Regulations 1992 as amended in 2002 Work at Height Regulations 2005 Other relevant Regulations in brief

18 INTERNATIONAL ASPECTS OF HEALTH AND SAFETY 18.1 18.2 18.3 18.4 18.5 18.6 18.7 18.8 18.9

Introduction The role and function of the International Labour Organization (ILO) Major occupational health and safety management systems Other key characteristics of a health and safety management system The role of the regulatory authorities The beneﬁts and problems associated with occupational health and safety management systems Conclusions on the three health and safety management systems Other minor additions to the International General Certiﬁcate Practice NEBOSH questions for the International General Certiﬁcate

19 STUDY SKILLS 19.1 19.2 19.3 19.4 19.5 19.6 19.7 19.8 19.9 19.10 19.11 19.12 19.13

Introduction Finding a place to study Planning for study Blocked thinking Taking notes Reading for study Organizing for revision Organizing information How does memory work? How to deal with exams The examiners’ reports Conclusion References

20 SPECIMEN ANSWERS TO NEBOSH EXAMINATIONS 20.1 20.2 20.3

INDEX

x

Introduction The written examinations NGC3 – The practical application Appendix 20.1 – Practical Assessment

383 384 386 389 392 394 396

402 402 404 405 411 414 414 415 415 417

418 418 418 418 419 419 419 419 420 420 422 423 424 424

425 425 425 431 436

443

Preface to the Third Edition

Introduction to Health and Safety at Work has quickly established itself, in its ﬁrst four years, as the foremost text for students taking the NEBOSH National General Certiﬁcate. It is also of great value to those studying for level 3 N/SVQ, the IOSH Managing Safely Award and similar management and supervisor focused learning. It has become a signiﬁcant work of reference for managers with health and safety responsibilities and it is therefore a matter of primary importance that it should be kept up-to-date, as far as is possible, with new legislation and recent developments. This third edition has been produced in order to update the health and safety legislation, with particular regard to changes in legislation relating to ﬁre, construction (CDM), asbestos, vibration, noise, hazardous waste and the environment. The most signiﬁcant change since the second edition has been the introduction of the unitized NEBOSH National General Certiﬁcate. The course has been divided into three distinct units each of which is assessed separately. This development offers the opportunity for additional and more ﬂexible course formats and students may now study parallel courses (in, say, ﬁre and construction) without repeating the management unit. Students who decide to take individual units will, on passing, receive a Unit Certiﬁcate. There were also some minor changes to the syllabus – safety in the use of lifting and moving equipment, construction health hazards, further controls of substances that can cause cancer, asthma or damage to genes and the safe storage of incompatible wastes. Following advice from several reviewers, we have taken the opportunity to introduce a new chapter on NEBOSH assessment – Specimen answers to NEBOSH examinations (Chapter 20). This includes two long answer questions, four short answer questions and a specimen practical application (or assessment). Some more recent examination questions have been added. Since the ﬁrst edition of this book was published, there has been a change in the style of examination questions and some topics, such as swimming pools and kitchens, are not speciﬁcally mentioned in the syllabus. Many questions now cover the contents of more than one chapter. It is recommended that students have sight of the published examiners’ reports which are available from NEBOSH. These reports not only provide an excellent guide on the expected answers to the questions but also indicate areas of student misunderstanding. Since 1 September 2004 there have been changes in the National Qualiﬁcations Framework (NQF) that are relevant to the NEBOSH General Certiﬁcate. However, up to Level 3 the NQF is unchanged and therefore its effect on the certiﬁcate will be minimal. The certiﬁcate syllabus is designed to provide the underpinning knowledge for the ‘Health and Safety for People at Work’ standard, an approved level 3 vocational standard developed by the Employment National Training Organization (ENTO). The syllabus is unitized to make it as compatible as possible with short courses based on the eight units of the ENTO standard. The NEBOSH National General Certiﬁcate is accredited as a level 3 award by the Qualiﬁcations and Curriculum Authority (QCA). More detailed information on these eight units is available in the guide to the NEBOSH National General Certiﬁcate. The third edition, which continues to closely follow the eight units, will therefore be particularly useful to people involved with the ‘Health and Safety for People at Work’ level 3 ENTO standard. As mentioned earlier, the certiﬁcate syllabus has been updated to include much of the new legislation. However, it is the policy of NEBOSH to examine new relevant legislation six months after its introduction whether it is speciﬁcally mentioned in the syllabus document or not. Finally, one of the objectives of the book is to provide a handbook for the use of any person who has health and safety as part of their responsibilities. We thought that it would be helpful, therefore, to keep the few useful topics

xi

Preface to the third edition which are outside the syllabus. These include more on the International Labour Organization, managing occupational road safety (Chapter 9), fast track settlement of compensation claims following the Woolfe reforms (Chapter 8) and the effects of alcohol and drugs on occupational health and safety (Chapter 15). A sample question on the effects of alcohol has also been included. We hope that you ﬁnd this new edition to be useful. Phil Hughes Ed Ferrett

xii

Acknowledgements

Throughout the book deﬁnitions used by the relevant legislation, the Health and Safety Commission, the Health and Safety Executive, and advice published in Approved Codes of Practice or various Health and Safety Commission/ Executive publications have been utilized. Most of the references produced at the end of each Act or Regulation summary in Chapter 20, are drawn from the HSE Books range of publications. At the end of each chapter, there are some examination questions taken from recent NEBOSH National General Certiﬁcate papers. Some of the questions may include topics which are covered in more than one chapter. The answers to these questions are to be found within the preceding chapter of the book. NEBOSH publishes a very full examiners’ report after each public examination which gives further information on each question. Most accredited NEBOSH training centres will have copies of these reports and further copies may be purchased directly from NEBOSH. The authors would like to thank NEBOSH for giving them permission to use these questions. The authors’ grateful thanks go to Liz Hughes for proof reading and patience and to Jill Ferrett for encouraging Ed Ferrett to keep at the daunting task of text preparation. The authors are particularly grateful to Liz for the excellent study guide that she has written for all NEBOSH students, which is included at the end of this book and for the section on Report Writing (8.9). Liz gained an honours degree in psychology at the University of Warwick, later going on to complete a masters degree at the same university. She taught psychology in further and higher education, where most of her students were either returning to education after a gap of many years, or were taking a course to augment their existing professional skills. She went on to qualify as a social worker specializing in mental health, and later moved into the voluntary sector where she managed development for a number of years. Liz then helped to set up and manage training for the National Schizophrenia Fellowship (now called Rethink) in the Midlands. We would also like to acknowledge the contribution made by Hannah Ferrett for the help that she gave during the research for the book and with some of the word processing. The advice given on the specimen practical application by John Tremelling, Health and Safety Consultant from Penzance, is also gratefully acknowledged. We would like to thank Teresa Budworth, the Chief Executive of NEBOSH, for her support during this third edition and various HSE staff for their generous help and advice. Finally, we would like to thank Stephen Vickers the immediate past Chief Executive of NEBOSH for his encouragement at the beginning of the project and Doris Funke and all the production team at Elsevier who have worked hard to translate our dream into reality.

xiii

This page intentionally left blank

About the authors

Phil Hughes MBE is a well-known UK safety professional with over thirty years world-wide experience as Head of Environment Health and Safety at two large multinationals, Courtaulds and Fisons. Phil started in health and safety in the Factory Inspectorate at the Derby District in 1969 and moved to Courtaulds in 1974. He joined IOSH in that year and became Chairman of the Midland Branch, National Treasurer and then President in 1990–91. Phil has been very active on the NEBOSH Board for over ten years and served as Chairman from 1995–2001. He is also a Professional Member of the American Society of Safety Engineers and has lectured widely throughout the world. Phil received the RoSPA Distinguished service award in May 2001 and became a Director and Trustee of RoSPA in 2003. He received an MBE in the New Year Honours List 2005 for services to Health and Safety.

Ed Ferrett is an experienced health and safety consultant who has practised for over twenty years. With a PhD and honours degree in Mechanical Engineering from Nottingham University, Ed spent thirty years in Higher and Further Education, retiring as the Head of the Faculty of Technology of Cornwall College in 1993. Since then he has been an independent consultant to several public and private sector organizations including construction businesses, the Regional Health and Safety Adviser for the Government Ofﬁce (West Midlands) and was Chair of West of Cornwall Primary Care NHS Trust for 6 years until 2006. Ed has been a member of the NEBOSH Board since 1995 and Vice Chair for the last 8 years. He has delivered many health and safety courses and is a lecturer in NEBOSH courses at the Cornwall Business School and for other course providers. Ed is a Chartered Engineer and a Member of IOSH.

xv

List of principal abbreviations

Most abbreviations are defined within the text. Abbreviations are not always used if it is not appropriate within the particular context of the sentence. The most commonly used ones are as follows: ACOP ACM CAR CBI CECA CDM CHIP CIRA CONIAC COSHH dB(A) dB(C) DSE DSEAR EAV EC ELV EMAS EPA EU FPA HAV HSC HSE HSW Act IOSH LEAL LOLER MCG MHSW MHOR MEL MoT NAWR NEBOSH OHSAS OSH PPE PUWER

xvi

Approved Code of Practice Asbestos containing material Control of Asbestos Regulations The Confederation of British Industry The Civil Engineering Contractors Association The Construction (Design and Management) Regulations Chemicals(Hazard Information and Packaging) Regulations Construction Industry Research and Information Association Construction Industry Advisory Committee Control of Substances Hazardous to Health Regulations Decibel (A-weighted) Decibel (C-weighted) Display Screen Equipment Regulations Dangerous Substances and Explosive Atmospheres Regulation Exposure Action Value European Community Exposure Limit Value Employment Medical Advisory Service Environmental Protection Act 1990 European Union Fire Precautions Act 1971 Hand-Arm Vibration Health and Safety Commission Health and Safety Executive Health and Safety at Work etc. Act 1974 Institution of Occupational Safety and Health Lower Exposure Action Level Lifting Operations and Lifting Equipment Regulations 1998 The Major Contractors Group Management of Health and Safety at Work Regulations Manual Handling Operations Regulations Maximum exposure limit Ministry of Transport (still used for vehicle tests) Control of Noise at Work Regulations National Examination Board in Occupational Safety and Health Occupational Health and Safety Assessment Series Occupational Safety and Health Personal Protective Equipment The Provision and Use of Work Equipment Regulations

List of principal abbreviations RIDDOR ROES RRFSO SPL STEL TUC UEAL UK VAWR WAHR WBV WEL WRULD

The Reporting of Injuries, Diseases and Dangerous Occurrences Regulations Representative(s) of Employee Safety Regulatory Reform Fire Safety Order Sound Pressure Level Short-term Exposure Limit Trades Union Congress Upper Exposure Action Level United Kingdom Vibration At Work Regulations Work at Height Regulations Whole Body Vibration Workplace Exposure Limit Work-related Upper Limb Disorder

xvii

Illustrations credits

Figure 1.5

Source HSE. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 1.12

From HSG 65 Successful Health and Safety Management (HSE Books 1997) ISBN 0717612767. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 4.3

From HSG 57 Seating at Work (HSE Books 1998) ISBN 0717612317. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 4.7

From HSG 48 Reducing Error and Influencing Behaviour (HSE Books 1999) ISBN 0717624528. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 5.1

From HSG 149 Backs for the Future: Safe Manual Handling in Construction (HSE Books 2000) ISBN 0717611221. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 6.1

Reproduced with permission from The Argus, Brighton.

Figure 6.4

From HSG 150 (rev1) Health and Safety in Construction (HSE Books 2001) ISBN 0717621065. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 6.7

From PUWER 1998. Provision and Use of Work Equipment Regulations 1998: Open Learning Guidance (HSE Books 1999) ISBN 0717624595. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 6.8

Cover of INDG 98 Permit-to-Work Systems (HSE 1998) ISBN 0717613313. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 7.1

From HSG 65 Successful Health and Safety Management (HSE Books 1997) ISBN 0717612767. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 7.2

From Guide to Measuring Health and Safety Performance (HSE 2001). © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 8.4

From BI 510 Accident Book (HSE Books 2003) ISBN 0717626032. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 8.5

From HSE 31 REV1 RIDDOR Explained: Reporting of Injuries, Diseases and Dangerous Occurances Regulations (HSE Books 1999) ISBN 0717624412. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 9.1

From HSG 155 Slips and Trips (HSE Books 1996) ISBN 0717611450. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 9.4a

For (a) only: From HSG 76 Health and Safety in Retail and Wholesale Warehouses (HSE Books 1992) ISBN 0118857312. © Crown copyright material is reproduced with the permission of the Controller of HMSO and the Queen’s Printer for Scotland.

xviii

Illustrations credits Figure 9.6

From HSG 6 Safety in Working with Lift Trucks (HSE Books 2000) ISBN 0717617815. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 9.7

From HSG 136 Workplace Transport Safety (HSE Books 1995) ISBN 0717609359. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.4

From L 23 Manual Handling Operations – Guidance on Regulations (HSE Books 2004) ISBN 071762823X. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.5

From Manual Handling in the Health Services (HSE Books 1998) ISBN 0717612481. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.6

From HSG 115 Manual Handling Solutions You Can Handle (HSE Books 1994) ISBN 0717606937. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.8a

From HSG 115 Manual Handling Solutions You Can Handle (HSE Books 1994) ISBN 0717606937. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.8b

From HSG 115 Manual Handling Solutions You Can Handle (HSE Books 1994) ISBN 0717606937. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.8c

From HSG 115 Manual Handling Solutions You Can Handle (HSE Books 1994) ISBN 0717606937. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.9

From HSG 149 Backs for the Future: Safe Manual Handling in Construction (HSE Books 2000) ISBN 0717611221. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 10.10

From HSG 76 Health and Safety in Retail and Wholesale Warehouses (HSE Books 1992) ISBN 0118857312. Crown copyright material is reproduced with the permission of the Controller of HMSO and the Queen’s Printer for Scotland.

Figure 10.13

From HSG 150 (rev1) Health and Safety in Construction (HSE Books 2001) ISBN 0717621065. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 11.4

Courtesy of Draper.

Figure 11.6

Courtesy of Draper.

Figure 11.10

Reprinted from Safety with Machinery, John Ridley and Dick Pearce, pages 20–29, 2005, with permission from Elsevier.

Figure 11.12

Reprinted from Safety with Machinery, John Ridley and Dick Pearce, pages 20–29, 2005, with permission from Elsevier.

Figure 11.13

Courtesy of Allen-Bradley Guardmaster brand from Rockwell Automation.

Figure 11.14

Reprinted from Safety with Machinery, John Ridley and Dick Pearce, page 63, 2005, with permission from Elsevier.

Figure 11.15a Reprinted from Safety with Machinery, John Ridley and Dick Pearce, pages 61 and 62, 2005, with permission from Elsevier.

xix

Illustrations credits Figure 11.15b Reprinted from Safety with Machinery, John Ridley and Dick Pearce, pages 61 and 62, 2005, with permission from Elsevier. Figure 11.16

Courtesy of Allen-Bradley Guardmaster brand from Rockwell Automation.

Figure 11.17

Reprinted from Safety with Machinery, John Ridley and Dick Pearce, page 79, 2005, with permission from Elsevier.

Figure 11.18

Courtesy of Canon.

Figure 11.19

Courtesy of Fellowes.

Figure 11.20

Courtesy of Draper.

Figure 11.21a Courtesy of Draper. Figure 11.21b Courtesy of Draper. Figure 11.22

Courtesy of Atco-Qualcast.

Figure 11.25

Picture supplied courtesy of STIHL GB.

Figure 11.26

Courtesy of Pakawaste.

Figure 11.27

Courtesy of Winget.

Figure 11.28

From L 114 Safe Use of Woodworking Machinery (HSE Books 1998) ISBN 0717616304. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 12.2

Courtesy of Stocksigns.

Figure 12.6a

Courtesy of DeWalt.

Figure 12.6b

Courtesy of DeWalt.

Figure 12.6c

Courtesy of DeWalt.

Figure 12.7a

From Essentials of Health and Safety (HSE Books 1999) ISBN 071760716X. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 12.7b

From Essentials of Health and Safety (HSE Books 1999) ISBN 071760716X. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 12.8a

From Essentials of Health and Safety (HSE Books 1999) ISBN 071760716X. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 12.8b

From Essentials of Health and Safety (HSE Books 1999) ISBN 071760716X. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 13.12a Courtesy of Armagard. Figure 13.12b Courtesy of Armagard. Figure 13.12c Courtesy of Armagard. Figure 13.13

Courtesy of NEBOSH.

Figure 14.2a

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, pages 240 and 248, 2002, with permission from Elsevier.

Figure 14.2b

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, pages 240 and 248, 2002, with permission from Elsevier.

xx

Illustrations credits Figure 14.3

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, page 9, 2002, with permission from Elsevier.

Figure 14.4

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, page 8, 2002, with permission from Elsevier.

Figure 14.5

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, page 340, 2002, with permission from Elsevier.

Figure 14.6

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, page 363, 2002, with permission from Elsevier.

Figure 14.8

Courtesy of Draeger Safety UK Limited.

Figure 14.9

From HSG 54 Maintenance, Examination and Testing of Local Exhaust Ventilation (HSE Books 1998) ISBN 0717614859. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 14.10

From HSG 202 General Ventilation in the Workplace (HSE Books 2000) ISBN 0717617939. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 14.11

Courtesy of Draper.

Figure 14.12a From HSG 53 The Selection, Use and Maintenance of Respiratory Protective Equipment (HSE Books 1998) ISBN 0717615375. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland. Figure 14.12b From HSG 53 The Selection, Use and Maintenance of Respiratory Protective Equipment (HSE Books 1998) ISBN 0717615375. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland. Figure 14.12c From HSG 53 The Selection, Use and Maintenance of Respiratory Protective Equipment (HSE Books 1998) ISBN 0717615375. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland. Figure 14.13

Courtesy of Draper.

Figure 15.1

From HSG 121 A Pain in Your Workplace (HSE Books 1994) ISBN 0717606686. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 15.3

From INDG 175 REV1 Health Risks from Hand-Arm Vibration (HSE Books 1998) ISBN 0717615537. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 15.4

From HSG 170 Vibration Solutions (HSE Books 1997) ISBN 0717609545. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 15.7a

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, page 195, 2002, with permission from Elsevier.

Figure 15.7b

Reprinted from Anatomy and Physiology in Health and Illness Ninth edition, Waugh and Grant, page 195, 2002, with permission from Elsevier.

Figure 15.9

From L 108 Reducing Noise at Work (HSE Books 1998) ISBN 0717615111. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 15.10

Source: Heat Stress Card published by the Occupational Safety & Health Administration, U.S.A.

xxi

Illustrations credits Figure 15.12

From INDG 69 (REV) Violence at Work: A Guide for Employers (HSE Books 2000) ISBN 0717612716. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 16.1

From HSG 151 Protecting the Public – Your Next Move (HSE Books 1997) ISBN 0717611485. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 16.3

From HSG 185 Health and Safety in Excavations (HSE Books 1999) ISBN 0717615634. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 16.4

From CIS 49 REV1 General Access Scaffolds and Ladders. Construction Information Sheet No. 49 (revision) (HSE Books 2003). © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 16.5

From www.brattsladders.com

Figure 16.6b

From HSG 149 Backs for the Future: Safe Manual Handling in Construction (HSE Books 2000) ISBN 0717611221. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 16.8

From HSG 150 (rev1) Health and Safety in Construction (HSE Books 2001) ISBN 0717621065. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 16.9

From HSG 185 Health and Safety in Excavations (HSE Books 1999) ISBN 0717615634. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

Figure 17.1

From INDG 350 The idiot’s guide to CHIP: Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 (HSE Books 2002) ISBN 0717623335. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer.

Figure 18.6

From HSG 65 Successful Health and Safety Management (HSE Books 1997) ISBN 0717612767. © Crown copyright material is reproduced with the permission of the Controller of HMSO and Queen’s Printer for Scotland.

xxii

1

Health and safety foundations

1.1 Introduction Occupational health and safety is relevant to all branches of industry, business and commerce including traditional industries, information technology companies, the National Health Service, care homes, schools, universities, leisure facilities and ofﬁces. The purpose of this chapter is to introduce the foundations on which appropriate health and safety systems may be built. Occupational health and safety affects all aspects of work. In a low hazard organization, health and safety may be supervised by a single competent manager. In a high hazard manufacturing plant, many different specialists, such as engineers (electrical, mechanical and civil), lawyers, medical doctors and nurses, trainers, work planners and supervisors, may be required to assist the professional health and safety practitioner in ensuring that there are satisfactory health and safety standards within the organization. There are many obstacles to the achievement of good standards. The pressure of production or performance targets, ﬁnancial constraints and the complexity of the organization are typical examples of such obstacles. However, there are some powerful incentives for organizations to strive for high health and safety standards. These incentives are moral, legal and economic. Corporate responsibility, a term used extensively in the 21st Century world of work, covers a wide range of issues. It includes the effects that an organization’s business has on the environment, human rights and third world poverty. Health and safety in the workplace is an important corporate responsibility issue. Corporate responsibility has various deﬁnitions. However, broadly speaking it covers the ways in which organizations manage their core business to add social, environmental and economic value in order to produce

a positive, sustainable impact on both society and the business itself. Terms such as ‘corporate social responsibility’, ‘socially responsible business’, and ‘corporate citizenship’ all refer to this concept. The UK Health and Safety Executive believes that its mission is to ensure that the risks to health and safety of workers are properly controlled. In terms of corporate responsibility, they are working to encourage organizations to: ➤ improve management systems to reduce injuries and ill health ➤ demonstrate the importance of health and safety issues at board level ➤ report publicly on health and safety issues within their organization, including their performance against targets. The HSE believe that effective management of health and safety: ➤ is vital to employee well-being ➤ has a role to play in enhancing the reputation of businesses and helping them achieve high-performance teams ➤ is ﬁnancially beneﬁcial to business.

1.2 Some basic definitions Before a detailed discussion of health and safety issues can take place, some basic occupational health and safety deﬁnitions are required: Health – the protection of the bodies and minds of people from illness resulting from the materials, processes or procedures used in the workplace.

1

Introduction to Health and Safety at Work Safety – the protection of people from physical injury. The borderline between health and safety is ill-deﬁned and the two words are normally used together to indicate concern for the physical and mental well-being of the individual at the place of work. Welfare – the provision of facilities to maintain the health and well-being of individuals at the workplace. Welfare facilities include washing and sanitation arrangements, the provision of drinking water, heating, lighting, accommodation for clothing, seating (when required by the work activity), eating and rest rooms. First aid arrangements are also considered as welfare facilities. Occupational or work-related ill-health – is concerned with those illnesses or physical and mental disorders that are either caused or triggered by workplace activities. Such conditions may be induced by the particular work activity of the individual or by activities of others in the workplace. The time interval between exposure and the onset of the illness may be short (e.g. asthma attacks) or long (e.g. deafness or cancer).

Figure 1.1

2

At work.

Environmental protection – arrangements to cover those activities in the workplace which affect the environment (in the form of ﬂora, fauna, water, air and soil) and, possibly, the health and safety of employees and others. Such activities include waste and efﬂuent disposal and atmospheric pollution. Accident – deﬁned by the Health and Safety Executive as ‘any unplanned event that results in injury or ill health of people, or damage or loss to property, plant, materials or the environment or a loss of a business opportunity’. Other authorities deﬁne an accident more narrowly by excluding events that do not involve injury or illhealth. This book will always use the Health and Safety Executive deﬁnition. Near miss – is any incident that could have resulted in an accident. Knowledge of near misses is very important since research has shown that, approximately, for every 10 ‘near miss’ events at a particular location in the workplace, a minor accident will occur. Dangerous occurrence – is a ‘near miss’ which could have led to serious injury or loss of life. Dangerous

Health and safety foundations occurrences are deﬁned in the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995 (often known as RIDDOR) and are always reportable to the Enforcement Authorities. Examples include the collapse of a scaffold or a crane or the failure of any passenger carrying equipment. Hazard and risk – a hazard is the potential of a substance, activity or process to cause harm. Hazards take many forms including, for example, chemicals, electricity and working from a ladder. A hazard can be ranked relative to other hazards or to a possible level of danger. A risk is the likelihood of a substance, activity or process to cause harm. A risk can be reduced and the hazard controlled by good management. It is very important to distinguish between a hazard and a risk – the two terms are often confused and activities such as construction work are called high risk when they are high hazard. Although the hazard will continue to be high, the risks will be reduced as controls are implemented. The level of risk remaining when controls have been adopted is known as the residual risk. There should only be high residual risk where there is poor health and safety management and inadequate control measures.

1.3 The legal framework for health and safety 1.3.1

Sub-divisions of law

There are two sub-divisions of the law that apply to health and safety issues: criminal law and civil law.

Criminal law Criminal law consists of rules of behaviour laid down by the Government or the State and, normally, enacted by Parliament through Acts of Parliament. These rules or Acts are imposed on the people for the protection of the people. Criminal law is enforced by several different Government Agencies who may prosecute individuals for contravening criminal laws. It is important to note that, except for very rare cases, only these Agencies are able to decide whether to prosecute an individual or not. An individual who breaks criminal law is deemed to have committed an offence or crime and, if he is prosecuted, the court will determine whether he is guilty or not. If he is found guilty, the court could sentence him to a ﬁne or imprisonment. Due to this possible loss of liberty, the level of proof required by a criminal court is very high and is known as proof ‘beyond reasonable doubt’, which is as near certainty as possible. While the prime object of a criminal court is the allocation

of punishment, the court can award compensation to the victim or injured party. One example of criminal law is the Road Trafﬁc Acts which are enforced by the police. However, the police are not the only criminal law enforcement agency. The Health and Safety at Work Act is another example of criminal law and this is enforced either by the Health and Safety Executive or Local Authority Environmental Health Ofﬁcers. Other agencies which enforce criminal law include the Fire Authority, the Environment Agency, Trading Standards and Customs and Excise. There is one important difference between procedures for criminal cases in general and criminal cases involving health and safety. The prosecution in a criminal case has to prove the guilt of the accused beyond reasonable doubt. While this obligation is not totally removed in health and safety cases, section 40 of the Health and Safety at Work Act 1974 transferred, where there is a duty to do something ‘so far as is reasonably practicable’ or ‘so far as is practicable’ or ‘use the best practicable means’, the onus of proof to the accused to show that there was no better way to discharge his duty under the Act. However, when this burden of proof is placed on the accused, they need only satisfy the court on the balance of probabilities that what they are trying to prove has been done.

Civil law Civil law concerns disputes between individuals or individuals and companies. An individual sues another individual or company to address a civil wrong or tort (or delict in Scotland). The individual who brings the complaint to court is known as the plaintiff (pursuer in Scotland) and the individual or company who is being sued is known as the defendant (defender in Scotland). The civil court is concerned with liability and the extent of that liability rather than guilt or non-guilt. Therefore, the level of proof required is based on the ‘balance of probability’, which is a lower level of certainty than that of ‘beyond reasonable doubt’ required by the criminal court. If a defendant is found to be liable, the court would normally order him to pay compensation and possibly costs to the plaintiff. However, the lower the balance of probability, the lower the level of compensation awarded. In extreme cases, where the balance of probability is just over 50%, the plaintiff may ‘win’ his case but lose ﬁnancially because costs may not be awarded and the level of compensation low. The level of compensation may also be reduced through the defence of contributory negligence, which is discussed later under ‘Common Torts and Duties’. For cases involving health and safety, civil disputes usually follow accidents or illnesses and concern negligence or a breach of statutory duty. The vast majority of cases are settled

3

Introduction to Health and Safety at Work ‘out of court’. While actions are often between individuals, where the defendant is an employee who was acting in the course of his employment during the alleged incident, the defence of the action is transferred to his employer – this is known as vicarious liability. The civil action then becomes one between the individual and a company. The Employers’ Liability (Compulsory Insurance) Act makes it a legal requirement for all employers to have employers’ liability insurance. This ensures that any employee, who successfully sues his or her employer following an accident, is assured of receiving compensation irrespective of the ﬁnancial position of the employer.

court by enforcement ofﬁcers (Health and Safety Executive or Local Authority Environmental Health Ofﬁcers) and they are tried by a bench of three lay magistrates (known as Justices of the Peace) or a single district judge. The lay magistrates are members of the public, usually with little previous experience of the law, whereas a district judge is legally qualiﬁed. The Magistrates Court has limited powers with a maximum ﬁne of £5000 (for employees) to £20 000 for employers or for those who ignore prohibition notices. Magistrates are also able to imprison for up to six months for breaches of enforcement notices. The vast majority of health and safety criminal cases are dealt with in the Magistrates Court.

Crown Court

1.4 The legal system in England and Wales The description which follows applies to England and Wales (and, with a few minor differences to Northern Ireland). Only the court functions concerning health and safety are mentioned. Figure 1.2 shows the court hierarchy in schematic form.

1.4.1

Criminal law

Magistrates Courts Most criminal cases begin and end in the Magistrates Courts. Health and safety cases are brought before the

The Crown Court hears the more serious cases, which are passed to them from the Magistrates Court – normally because the sentences available to the magistrates are felt to be too lenient. Cases are heard by a judge and jury, although some cases are heard by a judge alone. The penalties available to the Crown Court are an unlimited ﬁne and up to two years imprisonment for breaches of enforcement notices. The Crown Court also hears appeals from the Magistrates Court. Appeals from the Crown Court are made to the Court of Appeal (Criminal Division) who may then give leave to appeal to the most senior court in the country – the House of Lords. The most senior judge at the Court of Appeal is the Lord Chief Justice.

European Courts

House of Lords

Court of Appeal

Figure 1.2

4

Employment Appeals Tribunal

High Court Queens Bench Division

Crown Court

Employment Tribunal

County Court

Magistrates Court

Civil Law

Criminal Law

The court system in England and Wales for health and safety.

Health and safety foundations 1.4.2

Civil law

County Court The lowest court in civil law is the County Court which only deals with minor cases (for compensation claims of up to £50 000 if the High Court agrees). Cases are normally heard by a judge sitting alone. For personal injury claims of less than £5000, a small claims court is also available.

The High Court of Judiciary, in which a judge and jury sit, has a similar role to the Crown Court and appeals are made to the Court of Criminal Appeal. The Outer House of the Court of Session deals with civil cases in a similar way to the English High Court. The Inner house of the Court of Session is the Appeal Court for civil cases. For both appeal courts, the House of Lords is the ﬁnal court of appeal. There are Industrial Tribunals in Scotland with the same role as those in England.

High Court Most health and safety civil cases are heard in the High Court (Queens Bench Division) before a judge only. It deals with compensation claims in excess of £50 000 and acts as an appeal court for the County Court. Appeals from the High Court are made to the Court of Appeal (Civil Division). The House of Lords receives appeals from the Court of Appeal or, on matters of law interpretation, directly from the High Court. The most senior judge at the Court of Appeal is the Master of the Rolls. The judges in the House of Lords are called Law Lords and are sometimes called upon to make judgments on points of law, which are then binding on lower courts. Such judgments form the basis of Common Law, which is covered later.

Other courts – Employment Tribunals These were established in 1964 and primarily deal with employment and conditions of service issues, such as unfair dismissal. However, they also deal with appeals over health and safety enforcement notices, disputes between recognized safety representatives and their employers and cases of unfair dismissal involving health and safety issues. There are usually three members who sit on a Tribunal. These members are appointed and are often not legally qualiﬁed. Appeals from the Tribunal may be made to the Employment Appeal Tribunal or, in the case of enforcement notices, to the High Court. Appeals from Tribunals can only deal with the clariﬁcation of points of law.

1.5 The legal system in Scotland Scotland has both criminal and civil courts but prosecutions are initiated by the procurator-ﬁscal rather than the Health and Safety Executive. The lowest criminal court is called the District Court and deals with minor offences. The Sheriff Court has a similar role to that of the Magistrates Court (for criminal cases) and the County Court (for civil cases), although it can deal with more serious cases involving a sheriff and jury.

1.6 European Courts There are two European Courts – the European Court of Justice and the European Court of Human Rights. The European Court of Justice, based in Luxembourg, is the highest court in the European Union (EU). It deals primarily with community law and its interpretation. It is normally concerned with breaches of community law by Member States and cases may be brought by other Member States or institutions. Its decisions are binding on all Member States. There is currently no right of appeal. The European Court of Human Rights, based in Strasbourg, is not directly related to the EU – it covers most of the countries in Europe including the 15 EU member states. As its title suggests, it deals with human rights and fundamental freedoms. With the introduction of the Human Rights Act 1998 in October 2000, many of the human rights cases are now heard in the UK.

1.7 Sources of law (England and Wales) There are two sources of law – common law and statute law.

1.7.1

Common law

Common law dates from the eleventh century when William I set up Royal Courts to apply a uniform (common) system of law across the whole of England. Prior to that time, there was a variation in law, or the interpretation of the same law, from one town or community to another. Common law is based on judgments made by courts (or strictly judges in courts). In general, courts are bound by earlier judgments on any particular point of law – this is known as ‘precedent’. Lower courts must follow the judgments of higher courts. Hence judgments made by the Law Lords in the House of Lords form the basis of most of the common law currently in use. In health and safety, the legal deﬁnition of negligence, duty of care and terms such as ‘practicable’ and ‘as

5

Introduction to Health and Safety at Work Sub-divisions of Law Criminal Law Civil Law

Sources of Law Common Law Statute Law Overall Framework Law

Criminal

Common Law

Figure 1.3

Civil

Statute Law

The relationship between the sub-divisions and sources of law

The two sub-divisions of law may use either of the two sources of law. For example, murder is a common law crime. In terms of health and safety, however, criminal law is only based on statute law, whereas civil law may

6

be based on either common law or statute law. This relationship is shown in Figure 1.3. In summary, criminal law seeks to protect everyone in society whereas civil law seeks to recompense the individual citizen.

Statute law

Statute law is law which has been laid down by Parliament as Acts of Parliament. In health and safety, an Act of Parliament, the Health and Safety at Work Act 1974, lays down a general legal framework. Speciﬁc health and safety duties are, however, covered by Regulations or Statutory Instruments – these are also examples of statute law. If there is a conﬂict between statute and common law, statute law takes precedence. However, as with common law, judges interpret statute law usually when it is new or ambiguous. Although for health and safety, statute law is primarily the basis of criminal law, there is a tort of breach of statutory duty which can be used when a person is seeking damages following an accident or illness. Breaches of the Health and Safety at Work Act 1974 cannot be used for civil action but breaches of most of the Regulations produced by the Act may give rise to civil actions.

1.7.3

Statute Law

Sub-divisions and sources of law.

far as is reasonably practicable’ are all based on legal judgments and form part of the common law. Common law also provides the foundation for most civil claims made on health and safety issues.

1.7.2

Common Law

1.8

Common law torts and duties

1.8.1

Negligence

The only tort (civil wrong) of real signiﬁcance in health and safety is negligence. Negligence is the lack of reasonable care or conduct which results in the injury, damage (or ﬁnancial loss) of or to another. Whether the act or omission was reasonable is usually decided as a result of a court action. There have been two important judgments that have deﬁned the legal meaning of negligence. In 1856, negligence was judged to involve actions or omissions and the need for reasonable and prudent behaviour. In 1932, Lord Atkin said, You must take reasonable care to avoid acts or omissions which you reasonably foresee would be likely to injure your neighbour. Who then, in law is my neighbour? The answer seems to be persons who are so closely and directly affected by my act that I ought reasonably to have them in contemplation as being so affected when I am directing

Health and safety foundations my mind to the acts or omissions which are called in question. It can be seen, therefore, that for negligence to be established, it must be reasonable and foreseeable that the injury could result from the act or omission. In practice, the Court may need to decide whether the injured party is the neighbour of the perpetrator. A collapsing scaffold could easily injure a member of the public who could be considered a neighbour to the scaffold erector. An employee who is suing his employer for negligence, needs to establish the following three criteria: ➤ a duty was owed to him by his employer since the incident took place during the course of his employment ➤ there was a breach of that duty because the event was foreseeable and all reasonable precautions had not been taken ➤ the breach resulted in the speciﬁc injury, disease, damage and/or loss suffered. These tests should also be used by anyone affected by the employer’s undertaking (such as contractors and members of the public) who is suing the employer for negligence. If the employer is unable to defend against the three criteria, two further partial defences are available. It could be argued that the employee was fully aware of the risks that were taken by not complying with safety instructions (known as volenti non fit injuria or ‘the risk was willingly accepted’). This defence is unlikely to be totally successful because courts have ruled that employees have not accepted the risk voluntarily since economic necessity forces them to work. The second possible defence is that of ‘contributory negligence’ where the employee is deemed to have contributed to the negligent act. This defence, if successful, can signiﬁcantly reduce the level of compensation (up to 80% in some cases). Any negligence claim must be made within a set time period.

1.8.2

Duties of care

Several judgments have established that employers owe a duty of care to each of their employees. This duty cannot be assigned to others, even if a consultant is employed to advise on health and safety matters or if the employees are sub-contracted to work with another employer. These duties may be sub-divided into four groups. Employers must: ➤ provide a safe place of work, including access and egress

➤ ➤ ➤ ➤

provide safe plant and equipment provide a safe system of work provide safe and competent fellow employees provide adequate levels of supervision, information, instruction and training.

Employer duties under common law are often mirrored in statute law. This, in effect, makes them both common law and statutory duties. These duties apply even if the employee is working at a third party premises or if he has been hired by his employer to work for another employer. The requirements of a safe workplace, including the maintenance of ﬂoors and the provision of walkways and safe stairways, for example, are also contained in the Workplace (Health, Safety and Welfare) Regulations 1992. The requirement to provide competent fellow employees includes the provision of adequate supervision, instruction and training. As mentioned earlier, employers are responsible for the actions of their employees (vicarious liability) provided that the action in question took place during the normal course of their employment.

1.9 Levels of statutory duty There are three levels of statutory duty which form a hierarchy of duties. These levels are used extensively in health and safety statutory (criminal) law but have been deﬁned by judges under common law. The three levels of duty are absolute, practicable and reasonably practicable.

1.9.1

Absolute duty

This is the highest level of duty and, often, occurs when the risk of injury is so high that injury is inevitable unless safety precautions are taken. It is a rare requirement regarding physical safeguards, although it was more common before 1992 when certain sections of the Factories Act 1961 were still in force. No assessment of risk is required but the duty is absolute and the employer has no choice but to undertake the duty. The verbs used in the Regulations are ‘must’ and ‘shall’. An example of this is Regulation 11(1) of the Provision and Use of Work Equipment Regulations concerning contact with a rotating stock bar which projects beyond a headstock of a lathe. Although this duty is absolute, it may still be defended using, for example, the argument that ‘all reasonable precautions and all due diligence’ were taken. This particular defence is limited to certain health and safety regulations such as The Electricity at Work Regulations and The Control of Substances Hazardous to Health Regulations.

7

Introduction to Health and Safety at Work Many of the health and safety management requirements contained in health and safety law place an absolute duty on the employer. The need for written safety policies and risk assessments when employee numbers rise above a basic threshold are examples of this.

1.9.2

Practicable

This level of duty is more often used than the absolute duty as far as the provision of safeguards is concerned and, in many ways, has the same effect. A duty that ‘the employer ensure, so far as is practicable, that any control measure is maintained in an efﬁcient state’ means that if the duty is technically possible or feasible then it must be done irrespective of any difﬁculty, inconvenience or cost. Examples of this duty may be found in the Provision and Use of Work Equipment Regulations (Regulation 11(2) (a and b)) and the Control of Lead at Work Regulations where Regulation 8 states, ‘Every employer who provides any control measure … shall ensure, so far as is practicable, that it is maintained in an efﬁcient state … in good repair …’.

1.9.3

Reasonably practicable

is a gross disproportion between them – the risk being insignificant in relation to the sacrifice – the defendants discharge the onus on them. In other words, if the risk of injury is very small compared to the cost, time and effort required to reduce the risk, then no action is necessary. It is important to note that money, time and trouble must ‘grossly outweigh’ not balance the risk. This duty requires judgment on the part of the employer (or his adviser) and clearly needs a risk assessment to be undertaken with conclusions noted. Continual monitoring is also required to ensure that risks do not increase. There are numerous examples of this level of duty, including the Manual Handling Operations Regulations and The Control of Substances Hazardous to Health Regulations. If organizations follow ‘good practice’, deﬁned by the HSE as ‘those standards which satisfy the law’, then they are likely to satisfy the ‘reasonably practicable’ test. Approved codes of practice and guidance published by the HSE describe and deﬁne many of these standards. The term ‘suitable and sufﬁcient’ is used to deﬁne the scope and extent required for health and safety risk assessment and may be interpreted in a similar way to reasonably practicable. More information is given on this deﬁnition in Chapter 5.

This is the most common level of duty in health and safety law and was deﬁned by Judge Asquith in Edwards v. the National Coal Board (1949) as follows: ‘Reasonably practicable’ is a narrower term than ‘physically possible’, and seems to me to imply that computation must be made by the owner in which the quantum of risk is placed on one scale and the sacrifice involved in the measures necessary for averting the risk (whether in time, money or trouble) is placed in the other, and that, if it be shown that there

Quantum of risk severity and likelihood of event

Sacrifice in time, money and trouble

Figure 1.4 Diagrammatic view of ‘reasonably practicable’.

8

1.10 The influence of the European Union (EU) on health and safety As Britain is part of the European Union, much of the health and safety law originates in Europe. Proposals from the European Commission may be agreed by member states. The member states are then responsible for making them part of their domestic law. In Britain itself and in much of Europe, health and safety law is based on the principle of risk assessment described above. The main role of the EU in health and safety is to harmonize workplace and legal standards and remove barriers to trade across member states. A directive from the EU is legally binding on each member state and must be incorporated into the national law of each member state. Directives set out speciﬁc minimum aims which must be covered within the national law. Some states incorporate Directives more speedily than others. Directives are proposed by the European Commission, comprising 25 commissioners, who are citizens of each of the member states. The proposed Directives are sent to the European Parliament which is directly elected from the member states. The European Parliament may accept, amend or reject the proposed Directives. The proposed Directives are then passed to the Council of Ministers who may accept the proposals on a qualiﬁed

Health and safety foundations majority vote, unless the European Parliament has rejected them, in which case, they can only be accepted on a unanimous vote of the Council. The Council of Ministers consists of one senior Government minister from each of the member states. The powers of the EU in health and safety law are derived from the Treaty of Rome 1957 and the Single European Act 1986. For health and safety, the Single European Act added two additional Articles – 100A and 118A. The 1997 Treaty of Amsterdam renumbered them as 95A and 138A respectively. Article 95A is concerned with health and safety standards of equipment and plant and its Directives are implemented in the UK by the Department of Trade and Industry. Article 138A is concerned with minimum standards of health and safety in employment and its Directives are implemented by the Health and Safety Commission/Executive. The objective of the Single European Act 1986 is to produce a ‘level playing ﬁeld’ for all member states so that goods and services can move freely around the EU without any one state having an unfair advantage over another. The harmonization of health and safety requirements across the EU is one example of the ‘level playing ﬁeld’. The ﬁrst introduction of an EU Directive into UK Health and Safety law occurred on 1 January 1993 when a Framework Directive on Health and Safety management and ﬁve daughter directives were introduced using powers contained in the Health and Safety at Work Act 1974 (Figures 1.5 and 1.6). These directives, known as the European Six Pack, covered the following areas: ➤ ➤ ➤ ➤ ➤ ➤

Figure 1.5 Health and Safety Law Poster – must be displayed or brochure given to employees.

Management of Health and Safety at Work Workplace Provision and Use of Work Equipment Manual Handling Personal Protective Equipment Display Screen Equipment.

Since 1993, several other EU Directives have been introduced into UK law. Summaries of the more common UK regulations are given in Chapter 17.

1.11 The Health and Safety at Work Act 1974 1.11.1

Background to the Act

The Health and Safety at Work Act resulted from the ﬁndings of the Robens Report, published in 1972. Earlier legislation had tended to relate to speciﬁc industries or workplaces. This resulted in over 5 m workers

Figure 1.6

Health and Safety at Work Act.

being unprotected by any health and safety legislation. Contractors and members of the public were generally ignored. The law was more concerned with the requirement for plant and equipment to be safe rather than the development of parallel arrangements for raising the health and safety awareness of employees. A further serious problem was the difﬁculty that legislation had in keeping pace with developments in technology. For example, following a court ruling in 1955 which, in effect, banned the use of grinding wheels throughout industry, it took 15 years to produce the Abrasive Wheels Regulations 1970 to address

9

Introduction to Health and Safety at Work the problem raised by the 1955 court judgment (John Summers and Sons Ltd. v. Frost). In summary, health and safety legislation before 1974 tended to be reactive rather than proactive. Lord Robens was asked, in 1970, to review the provision made for the health and safety of people at work. His report produced conclusions and recommendations upon which the Health and Safety at Work Act 1974 was based. The principal recommendations were as follows: ➤ there should be a single Act that covers all workers and that Act should contain general duties which should ‘inﬂuence attitudes’; ➤ the Act should cover all those affected by the employer’s undertaking such as contractors, visitors, students and members of the public; ➤ there should be an emphasis on health and safety management and the development of safe systems of work. This would involve the encouragement of employee participation in accident prevention. (This was developed many years later into the concept of the health and safety culture); ➤ enforcement should be targeted at ‘self-regulation’ by the employer rather than reliance on prosecution in the courts. These recommendations led directly to the introduction of the Health and Safety at Work etc. Act in 1974.

1.11.2

An overview of the Act

Health and Safety Commission (HSC) The Health and Safety at Work Act established the HSC and gave it the responsibility to draft new Regulations and to enforce them either through its executive arm, known as the Health and Safety Executive (HSE), or through the Local Authority Environmental Health Ofﬁcers (EHO). The HSC has equal representation from employers, trade unions and special interest groups. There is a proposal, currently out to consultation, to merge the HSC with the HSE into a single body with the HSC functions being performed by a non-executive board acting within the HSE.

Regulations The Health and Safety at Work Act is an Enabling Act which allows the Secretary of State to make further laws (known as regulations) without the need to pass another Act of Parliament. Regulations are law, approved by Parliament. These are usually made under the Health and Safety at Work Act, following proposals from the HSC. This applies to regulations based on EC Directives as well as ‘home-grown’ ones. It is a criminal offence to breach

10

a regulation and any breaches may result in enforcement action as explained later in this chapter (1.11.4). The Health and Safety at Work Act, and general duties in the Management Regulations, aim to help employers to set goals, but leave them free to decide how to control hazards and risks which they identify. Guidance and Approved Codes of Practice give advice, but employers are free to take other routes to achieving their health and safety goals, so long as they do what is reasonably practicable. But some hazards are so great, or the proper control measures so expensive, that employers cannot be given discretion in deciding what to do about them. Regulations identify these hazards and risks and set out speciﬁc action that must be taken. Often these requirements are absolute – employers have no choice but to follow them and there is no qualifying phrase of ‘reasonably practicable’ included. Some regulations apply across all organizations – the Manual Handling Regulations would be an example. These apply wherever things are moved by hand or bodily force. Equally, the Display Screen Equipment Regulations apply wherever visual display units are used at work. Other regulations apply to hazards unique to speciﬁc industries, such as mining or construction. Wherever possible, the HSC will set out the regulations as goals, and describe what must be achieved, but not how it must be done. Sometimes it is necessary to be prescriptive, and to spell out what needs to be done in detail, since some standards are absolute. For example, all mines should have two exits; contacts with live electrical conductors should be avoided. Sometimes European law requires prescription. Some activities or substances are so dangerous that they have to be licensed, for example, explosives and asbestos removal. Large, complex installations or operations require ‘safety cases’, which are large-scale risk assessments subject to scrutiny by the regulator. An example would be the recently privatized railway companies. They are required to produce safety cases for their operations.

Approved Code of Practice (ACOP) An ACOP is produced for most sets of regulations by the HSC and attempts to give more details on the requirements of the regulations. It also attempts to give the level of compliance needed to satisfy the regulations. ACOPs have a special legal status (sometimes referred to as quasi-legal). The relationship of an ACOP to a regulation is similar to the relationship of the Highway Code to the Road Trafﬁc Acts. A person is never prosecuted for contravening the Highway Code but can be prosecuted for contravening the Road Trafﬁc Acts. If a company is prosecuted for a breach of health and safety law and it is proved that it has not followed the relevant

Health and safety foundations provisions of the ACOP, a court can ﬁnd them at fault, unless the company can show that it has complied with the law in some other way. Since most health and safety prosecutions take place in a Magistrates Court, it is likely that the lay magistrates will consult the relevant ACOP as well as the regulations when dealing with a particular case. Therefore, in practice, an employer must have a good reason for not adhering to an ACOP. Codes of Practice generally are only directly legally binding if: ➤ the regulations or Act indicates that they are, for example, the Safety Signs and Signals Regulations Schedule 2 specify British Standard Codes of practice for alternative hand signals; or ➤ they are referred to in an Enforcement Notice.

Guidance Guidance, which has no formal legal standing, comes in two forms – legal and best practice. The Legal Guidance series of booklets is issued by the HSC and/or the HSE to cover the technical aspects of health and safety regulations. These booklets generally include the Regulations and the ACOP, where one has been produced. Best practice guidance is normally published in the HSG series of publications by the HSE. Examples of best practice guidance books include Health and safety in Construction HSG 150 and Lighting at Work HSG 38. An example of the relationship between these three forms of requirement/advice can be shown using a common problem found throughout industry and commerce – minimum temperatures in the workplace. Regulation 7 of the Workplace (Health, Safety and Welfare) Regulations states ‘(1) During working hours, the temperature in all workplaces inside buildings shall be reasonable’. The ACOP states ‘The temperature in workrooms should normally be at least 16 degrees Celsius unless much of the work involves severe physical effort in which case the temperature should be at least 13 degrees Celsius …’ It would, therefore, be expected that employers would not allow their workforce to work at temperatures below those given in the ACOP unless it was reasonable for them to do so (if, for example, the workplace was a refrigerated storage unit). Best practice guidance to cover this example is given in HSG 194 (Thermal Comfort in the Workplace) in which possible solutions to the maintenance of employee welfare in low temperature environments is given.

Health and Safety Executive (HSE) The prime function of the HSE is to monitor, review and enforce health and safety law and to produce codes of

practice and guidance. However, the HSE also undertakes many other activities, such as the compilations of health and safety statistics, leading national health and safety campaigns, investigations into accidents or complaints, visiting and advising employers and the production of a very useful website.

1.11.3

General duties and key sections of the act

A summary of the Health and Safety at Work Act is given under Chapter 17 (17.4) – only an outline will be given here.

Section 2 Duties of employers to employees To ensure, so far as is reasonably practicable, the health, safety and welfare of all employees. In particular: ➤ safe plant and systems of work ➤ safe use, handling, transport and storage of substances and articles ➤ provision of information, instruction, training and supervision ➤ safe place of work, access and egress ➤ safe working environment with adequate welfare facilities ➤ a written safety policy together with organizational and other arrangements (if there are 5 or more employees) ➤ consultation with safety representatives and formation of safety committees where there are recognized trade unions.

Section 3 Duties of employers to others affected by their undertaking A duty to safeguard those not in their employment but affected by the undertaking. This includes members of the public, contractors, patients, customers and students.

Section 4 Duties of landlords or owners To ensure that means of access and egress are safe for those using the premises.

Section 6 Duties of suppliers Persons who design, manufacture, import or supply any article or substance for use at work must ensure, so far as is reasonably practicable, that they are safe and without risk to health. Articles must be safe when they are set, cleaned, used and maintained. Substances must be without risk to health when they are used handled, stored or transported. This requires that information must be supplied on the safe use of the articles and substances. There may be a need to guarantee the required level of safety by undertaking tests and examinations.

11

Introduction to Health and Safety at Work

Figure 1.7

Employees at work.

Section 7 Duties of Employees Two main duties: ➤ to take reasonable care for the health and safety of themselves and others affected by their acts or omissions ➤ to co-operate with the employer and others to enable them to fulﬁl their legal obligations.

Section 8 No person is to misuse or interfere with safety provisions. (sometimes known as the‘horseplay section’)

Section 9

Figure 1.8

The inspector inspects.

Employees cannot be charged for health and safety requirements such as personal protective equipment.

Section 37 Personal liability of directors Where an offence is committed by a corporate body with the consent or connivance of, or is attributable to any neglect of a director or other senior ofﬁcer of the body, both the corporate body and the person are liable to prosecution.

1.11.4

Enforcement of the Act

Powers of inspectors Inspectors under the Act work either for the HSE or the Local Authority. Local Authorities are responsible for retail and service outlets such as shops (retail and wholesale), restaurants, garages, ofﬁces, residential homes, entertainment and hotels. The HSE are responsible for

12

all other work premises including the Local Authorities themselves. Both groups of inspectors have the same powers. The detailed powers of inspectors are given in Chapter 17. In summary an inspector has the right to: ➤ enter premises at any reasonable time, accompanied by a police ofﬁcer, if necessary ➤ examine, investigate and require the premises to be left undisturbed ➤ take samples, photographs and, if necessary, dismantle and remove equipment or substances ➤ require the production of books or other relevant documents and information ➤ seize, destroy or render harmless any substance or article ➤ issue enforcement notices and initiate prosecutions.

Health and safety foundations An inspector may issue a formal caution when an offence has been committed but it is deemed that the public interest does not require a prosecution. Formal cautions are not normally considered if the offender has already had a formal caution.

Enforcement notices

The courts also have the power to disqualify directors who are convicted of health and safety offences up to 5 years at the lower court and 15 years at the higher court. Finally, it is important to stress that imprisonment for health and safety offences is rare. From 1996 until 2005, only 5 people were sent to prison for health and safety offences.

There are two types of enforcement notices. Improvement notice – This identiﬁes a speciﬁc breach of the law and speciﬁes a date by which the situation is to be remedied. An appeal must be made to the Employment Tribunal within 21 days. The notice is then suspended until the appeal is either heard or withdrawn. Prohibition notice – This is used to halt an activity which the inspector feels could lead to a serious personal injury. The notice will identify which legal requirement is being or is likely to be contravened. The notice takes effect as soon as it is issued. As with the improvement notice, an appeal may be made to the Employment Tribunal but, in this case, the notice remains in place during the appeal process. There are two forms of prohibition notice: ➤ an immediate prohibition notice – this stops the work activity immediately until the speciﬁed risk is reduced ➤ a deferred prohibition notice – this stops the work activity within a speciﬁed time limit.

Penalties Magistrates Court (or Lower Court) The Magistrates Court deals with summary offences. For health and safety offences under sections 2–6 of the HSW Act, employers and others (self-employed, manufacturers and suppliers) may be ﬁned up to £20 000. For all other breaches of the HSW Act and breaches of health and safety regulations made under the Act, the maximum ﬁne is £5 000. Thus the maximum ﬁne that may be imposed on an employee is £5 000. For failure to comply with an enforcement notice or a court order, anybody may be ﬁned up to £20 000 or imprisoned for up to 6 months.

Crown Court (or Higher Court) The Crown Court deals with indictable offences. Fines are unlimited in the Crown Court for all health and safety offences and the possible imprisonment for up to 2 years for failure to comply with an enforcement notice or a court order. For the contravention of licensing requirements for nuclear installations, asbestos removal and the storage and manufacture of explosives, the lower court can ﬁne up to £5 000 whereas the higher court can impose an unlimited ﬁne and/or 2 years imprisonment.

Summary of the actions available to an Inspector Following a visit by an inspector to premises, the following actions are available to an inspector: ➤ ➤ ➤ ➤ ➤ ➤ ➤

take no action give verbal advice give written advice. formal caution serve an improvement notice serve a prohibition notice prosecute.

In any particular situation, more than one of these actions may be taken. The decision to prosecute will be made either when there is sufﬁcient evidence to provide a realistic possibility of conviction or when prosecution is in the public interest. Work-related deaths are investigated by the police jointly with the HSE or Local Authority to ascertain whether a charge of manslaughter (culpable homicide in Scotland) is appropriate. If the police decide not to pursue such a charge, the HSE or Local Authority will continue the investigation under health and safety law. A Corporate Manslaughter Bill is currently passing through Parliament and this offers the possibility of a new statutory offence when a work related death results from serious management failure. However, it is unlikely that there will be individual liability for company directors under the bill. Finally, the Health and Safety (Information for Employees) Regulations require that the Approved Poster entitled ‘Health and safety Law – what you should know’ is displayed or the Approved Leaﬂet is distributed. This information tells employees in general terms about the requirements of health and safety law. Employers must also inform employees of the local address of the enforcing authority (either the HSE or the local authority) and the Employment Medical Advisory Service. This should be marked on the poster or supplied with the leaﬂet. Since 1 July 2000 the latest version of the poster must be displayed or distributed. The revised text focuses on the modern framework of general duties of the employer and employee, supplemented by the some basic information on health and safety management and risk assessment. It includes two additional boxes: one

13

Introduction to Health and Safety at Work for details of trade union or other safety representatives and one of competent persons appointed to assist with health and safety and their responsibilities. The poster is shown in Figure 1.5.

1.12 The Management of Health and Safety at Work Regulations 1999 As mentioned earlier, on 1 January 1993, following an EC Directive, the Management of Health and Safety at Work Regulations became law in the United Kingdom. These regulations were updated in 1999 and are described in detail in Chapter 17. In many ways the regulations were not introducing concepts or replacing the 1974 Act – they simply reinforced or amended the requirements of the Health and Safety at Work Act. Some of the duties of employers and employees were re-deﬁned.

The information that should be supplied by employers under the regulations is: ➤ risks identiﬁed by any risk assessments including those notiﬁed to him by other employers sharing the same workplace ➤ the preventative and protective measures that are in place ➤ the emergency arrangements and procedures and the names of those responsible for the implementation of the procedures. Finally, it is important to note that the regulations outline the principles of prevention which employers and the self-employed need to apply so that health and safety risks are addressed and controlled. These principles are discussed in detail in Chapter 6.

1.12.2

Employees duties

Employees must:

1.12.1

Employers duties

Employers must: ➤ undertake suitable and sufﬁcient written risk assessments when there are 5 or more employees ➤ put in place effective arrangements for the planning, organization, control, monitoring and review of health and safety measures in the workplace (including health surveillance). Such arrangements should be recorded if there are more than four employees ➤ employ (to be preferred) or contract competent persons to help them comply with health and safety duties ➤ develop suitable emergency procedures. Ensure that employees and others are aware of these procedures and can apply them ➤ provide health and safety information to employees and others, such as other employers, the selfemployed and their employees who are sharing the same workplace and parents of child employees or those on work experience ➤ co-operate in health and safety matters with other employers who share the same workplace ➤ provide employees with adequate and relevant health and safety training ➤ provide temporary workers and their contract agency with appropriate health and safety information ➤ protect new and expectant mothers and young persons from particular risks ➤ under certain circumstances, as outlined in Regulation 6, provide health surveillance for employees.

14

➤ use any equipment or substance in accordance with any training or instruction given by the employer ➤ report to the employer any serious or imminent danger ➤ report any shortcomings in the employer’s protective health and safety arrangements.

1.13 Role and function of external agencies The Health and Safety Commission, Health and Safety Executive and the Local Authorities (a term used to cover County, District and Unitary Councils) are all external agencies which have a direct role in the monitoring and enforcement of health and safety standards. There are, however, three other external agencies which have a regulatory inﬂuence on health and safety standards in the workplace (see Figure 1.9).

1.13.1

Fire and Rescue Authority

The Fire and Rescue Authority is situated within a single or group of local authorities and is normally associated with rescue, ﬁre ﬁghting and the offering of general advice. It has also been given powers to enforce ﬁre precautions within places of work under ﬁre safety law. The powers of the Authority are very similar to those of the HSE on health and safety matters. The Authority issues Alteration Notices to work places and conducts routine and random ﬁre inspections (often to examine ﬁre risk

Health and safety foundations Health and Safety Commission District and Unitary Councils

Country Councils

HSE

FIre and rescue authorities

Workplace

Insurance companies

Home Office

Environment agency

Figure 1.9

The main external agencies that impact on the workspace.

assessments). It should be consulted during the planning stage of proposed building alterations when such alterations may affect the ﬁre safety of the building (e.g. means of escape). The Fire and Rescue Authority can issue both Enforcement and Prohibition Notices. The Authority can prosecute for offences against ﬁre safety law.

1.13.2 The Environment Agency (Scottish Environmental Protection Agency) The Environment Agency was established in 1995 and was given the duty to protect and improve the environment. It is the regulatory body for environmental matters and has an inﬂuence on health and safety issues. It is responsible for authorising and regulating emissions from industry. Other duties and functions of the agency include: ➤ ensuring effective controls of the most polluting industries ➤ monitoring radioactive releases from nuclear sites ➤ ensuring that discharges to controlled waters are at acceptable levels ➤ setting standards and issuing permits for the collection, transportation, processing and disposal of waste (including radioactive waste) ➤ enforcement of the Producer Responsibility Obligations (Packaging Waste) Regulations 1997. These result from an EC Directive which seeks to minimize packaging and re-cycle at least 50% of it ➤ enforcement of the Waste Electrical and Electronic Equipment (WEEE) Directive and its associated directives.

The Agency may prosecute in the criminal courts for the infringement of environmental law – in one case a ﬁne of £4 m was imposed.

1.13.3

Insurance companies

Insurance companies play an important role in the improvement of health and safety standards. Since 1969, it has been a legal requirement for employers to insure against liability for injury or disease to their employees arising out of their employment. This is called employers’ liability insurance and was covered earlier in this chapter. Certain public sector organizations are exempted from this requirement because any compensation is paid from public funds. Other forms of insurance include ﬁre insurance and public liability insurance (to protect members of the public). Premiums for all these types of insurance are related to levels of risk which is related to standards of health and safety. In recent years, there has been a considerable increase in the number and size of compensation claims and this has placed further pressure on insurance companies. Insurance companies are becoming effective health and safety regulators by weighing the premium offered to an organization according to its safety and/or ﬁre precaution record.

1.14 Sources of information on health and safety When anybody, whether a health and safety professional, a manager or an employee, is confronted with a health and safety problem, they will need to consult various

15

Introduction to Health and Safety at Work

Figure 1.10

Good standards prevent harm and save money.

items of published information to ascertain the scale of the problem and its possible remedies. The sources of this information may be internal to the organization and/ or external to it. Internal sources, which should be available within the organization include: ➤ accident and ill-health records and investigation reports ➤ absentee records ➤ inspection and audit reports undertaken by the organization and by external organizations such as the HSE ➤ maintenance, risk assessment (including COSHH) and training records ➤ documents which provide information to workers ➤ any equipment examination or test reports. External sources, which are available outside the organization, are numerous and include: ➤ health and safety legislation ➤ HSC/HSE publications, such as approved codes of practice, guidance documents, leaﬂets, journals, books and their website ➤ international (eg. ILO), European and British standards ➤ health and safety magazines and journals ➤ information published by trade associations, employer organizations and trade unions ➤ specialist technical and legal publications ➤ information and data from manufacturers and suppliers ➤ the internet and encyclopaedias.

16

Many of these sources of information will be referred to throughout this book.

1.15 Moral, legal and financial arguments for health and safety management 1.15.1

Moral arguments

The moral arguments are reﬂected by the occupational accident and disease rates.

Accident rates Accidents at work can lead to serious injury and even death. Although accident rates are discussed in greater detail in later Chapters, some trends are shown in Tables 1.1–1.4 below. A major accident is a serious accident typically involving a fracture of a limb or a 24 hour stay in a hospital. An ‘over three-day accident’s an accident which leads to more than 3 days off work. Statistics are collected on all people who are injured at places of work not just employees. It is important to note that since 1995 suicides and trespassers on the railways have been included in the HSE ﬁgures – this has led to a signiﬁcant increase in the ﬁgures. Table 1.1 details accidents involving all people at a place of work over a four year period. In 2005/06, there were 384 fatal injuries to members of the public and about 66% of these were due to acts of suicide or trespass on the railways. Table 1.2 shows, for the year 2004/05, the breakdown in accidents between employees, self-employed and members of the public. Table 1.3 shows the ﬁgures for

Health and safety foundations Table 1.1 Accidents involving all people at a place of work Injury

2002/03

2003/04

2004/05

2005/06

Death

623

606

593

596

Major

41 985

45 516

46 018

45 230

129 135

130 247

122 922

118 645

Over 3 day

Table 1.2 2004/05

Major

Over 3 day

Total

593

46 018

122 922

Employees

172 (29%)

30 451

121 779

51 (9%)

1 251

1 143

370 (62%)

14 316

Self employee Members of the public

n/a

Table 1.3 Accidents involving employees in the workplace 2002/03

2003/04

2004/05

2005/06

Death

183

168

172

160

Major

28 113

30 666

30 451

28 605

128 184

129 143

121 779

117 471

Over 3 day

Sector

Deaths

Majors

Agriculture

4.6

211.7

Construction

3.5

310.2

Transport

3.1

398.2

Manufacturing

1.4

180.3

Retail and wholesale

1.3

257.6

Hotel and catering

0.1

65.4

Health services

0.1

70.8

Accidents for different groups of people for

Deaths

Injury

Table 1.4 Accidents (per 100 000 workers) to all workers in various employment sectors (2005/06)

employees only. It shows that whilst there has been a decline in fatalities, major accidents have increased. Table 1.4 gives an indication of accidents in different employment sectors. These ﬁgures indicate that there is a need for health and safety awareness even in occupations which many would consider very low hazard, such as schools, the health services and hotels. In fact over 70% of all deaths occur in the service sector and manufacturing is considerably safer than construction and agriculture. In 2005/06, slips and trips accounted for 38% of major accidents whereas 41% of over three-day injuries were caused by handling, lifting and carrying. Although there has been a decrease in fatalities over recent years, there is still a very strong moral case for improvement in health and safety performance.

Disease rates Work related ill-health and occupational disease can lead to absence from work and, in some cases, to death.

Such occurrences may also lead to costs to the state (the Industrial Injuries Scheme) and to individual employers (sick pay and, possibly, compensation payments). In 2004/05 a major survey was undertaken into selfreported work related illness. In that year there were 2.0 m people in the UK suffered from work related illness of whom 600 000 were new cases in that year. This led to 28 m working days lost compared to 6 m due to workplace injury. The top four illnesses were: ➤ ➤ ➤ ➤

musculoskeletal disorders stress related lower respiratory disease deafness, tinnitus and other ear problems

1010 k 509 k 137 k 74 k

11.6 m working days were lost due to musculoskeletal disorders causing each sufferer to have 21 days off work on average and 12.8 m working days were lost due to stress, depression and anxiety causing each sufferer to have 31 days off work on average. Recent research has shown that one in ﬁve people who are on sickness leave from work for six weeks, will stay off work and leave paid employment. III-health statistics are estimated either from selfreported cases (Table 1.5) or from data supplied by hospital specialists and occupational physicians (Table 1.6). The number of self-reported cases will always be much higher than those seeking advice from hospitalbased specialists.

1.15.2

Legal arguments

The legal arguments, concerning the employer’s duty of care in criminal and civil law, have been covered earlier. Some statistics on legal enforcement indicate the legal consequences resulting from breaches in health and safety law. There have been some very high compensation

17

Introduction to Health and Safety at Work Table 1.5

Self-reported work-related illness for 2005/06

Type of Illness

Prevalence (thousands)

Musculoskeletal disorders of the back

437

Musculoskeletal disorders of the neck or upper limbs

374

Musculoskeletal disorders of the lower limbs

209

Musculoskeletal disorders in total

1020

Stress, depression or anxiety

420

Breathing or lung problems

156

Hearing problems Other (eg. skin or heart problems) Total

Prohibition Notice

2003/04

6798

4537

2004/05

5186

3285

2005/06

3787

2596

Year

Offences prosecuted

Convictions

2003/04

1720

1317

2004/05

1320

1025

2005/06

1012

741

294

1958

7 200

Musculoskeletal disorders

6 400

Dermatitis and other skin disorders

3 500

Respiratory Disease

3 200

Infections

1 300 400 22 000

awards for health and safety cases in the civil courts and ﬁnes in excess of £100,000 in the criminal courts. Table 1.7 shows the number of enforcement notices served over a three year period by the HSE. Most notices are served in the manufacturing sector followed by construction and agriculture. Local Authorities serve 40% of all improvement notices and 20% of all prohibition notices. Table 1.8 shows the number of prosecutions by the HSE over the same three year period and it can be seen that approximately 70% of those prosecuted are convicted. There was a reduction in the number of prosecutions over the three year period but provisional ﬁgures for 2006/07 show an increase of 20% in the number of prosecutions. HSE present 80% of the

18

Improvement Notice

68

Mental Health (stress, anxiety)

Total

Year

Table 1.8 Number of prosecutions by the HSE over a three year period

Table 1.6 Average annual incidence of new work-related illness reported by specialist doctors for 2003–05

Hearing Loss

Table 1.7 Number of enforcement notices issued over a three year period by the HSE

prosecutions and the remainder are presented by Local Authority Environmental Health Ofﬁcers. Most of these prosecutions are for infringements of the Construction Regulations and the Provision and Use of Work Equipment Regulations. There are some clear legal reasons for sound health and safety management systems.

1.15.3

Financial arguments

Costs of accidents Any accident or incidence of ill-health will cause both direct and indirect costs and incur and insured and an uninsured cost. It is important that all of these costs are taken into account when the full cost of an accident is calculated. In a study undertaken by the HSE, it was shown that indirect costs or hidden costs could be 36 times greater than direct costs of an accident. In other words, the direct costs of an accident or disease represent the tip of the iceberg when compared to the overall costs (Figure 1.11).

Direct costs These are costs which are directly related to the accident and may be insured or uninsured. Insured direct costs normally include: ➤ claims on employers and public liability insurance ➤ damage to buildings, equipment or vehicles ➤ any attributable production and/or general business loss.

Health and safety foundations Accident Iceberg Insured costs

£1

Injury, ill-health damage

Uninsured costs Product and material damage Legal costs Emergency supplies Cleaning up site Production delays Temporaray labour Lost orders Investigation time Fines Loss of expertise etc.

£8-36

Figure 1.11

Insured and uninsured costs.

Uninsured direct costs include: ➤ ﬁnes resulting from prosecution by the enforcement authority ➤ sick pay ➤ some damage to product, equipment, vehicles or process not directly attributable to the accident (e.g. caused by replacement staff) ➤ increases in insurance premiums resulting from the accident ➤ any compensation not covered by the insurance policy due to an excess agreed between the employer and the insurance company ➤ legal representation following any compensation claim.

Indirect costs These are costs which may not be directly attributable to the accident but may result from a series of accidents. Again these may be insured or uninsured. Insured indirect costs can include: ➤ a cumulative business loss ➤ product or process liability claims ➤ recruitment of certain replacement staff. Uninsured indirect costs include: ➤ loss of goodwill and a poor corporate image ➤ accident investigation time and any subsequent remedial action required ➤ production delays ➤ extra overtime payments ➤ lost time for other employees, such as a First Aider, who attend to the needs of the injured person

➤ the recruitment and training of most replacement staff ➤ additional administration time incurred ➤ ﬁrst aid provision and training ➤ lower employee morale possibly leading to reduced productivity Some of these items, such as business loss, may be uninsurable or too prohibitively expensive to insure. Therefore, insurance policies can never cover all of the costs of an accident or disease either because some items are not covered by the policy or the insurance excess is greater than the particular item cost.

1.16 The framework for health and safety management Most of the key elements required for effective health and safety management are very similar to those required for good quality, ﬁnance and general business management. Commercially successful organizations usually have good health and safety management systems in place. The principles of good and effective management provide a sound basis for the improvement of health and safety performance (see Figure 1.12). HSE, in HSG 65, have identiﬁed ﬁve key elements involved in a successful health and safety management system. The following Chapters will describe and discuss this framework in detail. The ﬁve elements are: 1.

Policy – a clear health and safety policy contributes to business efﬁciency and continuous improvement

19

Introduction to Health and Safety at Work

Information link

Policy development

Policy

Control link

Organizing

Auditing

Organizational development

Planning and implementing

Measuring performance

Developing techniques of planning, measuring and reviewing

Reviewing performance Feedback loop to improve performance

Figure 1.12

2.

3.

4.

Key elements of successful health and safety management.

throughout the operation. The demonstration of senior management involvement provides evidence to all stakeholders that responsibilities to people and the environment are taken seriously. The policy should state the intentions of the organization in terms of clear aims, objectives and targets. Organizing – A well deﬁned health and safety organization offering a shared understanding of the organization’s values and beliefs, at all levels of the organization is an essential component of a positive health and safety culture. An effective organization will be noted for good staff involvement and participation; high quality communications; the promotion of competency; and the empowerment and commitment of all employees to make informed contributions. Planning and implementing – A clear health and safety plan involves the setting and implementation of performance standards, targets and procedures through an effective health and safety management system. The plan is based on risk assessment methods to decide on priorities and set objectives for the effective control or elimination hazards and the reduction of risks. Measuring success requires the establishment of practical plans and performance targets against which achievements can be identiﬁed. Measuring performance – This includes both active (sometimes called proactive) and reactive monitoring to see how effectively the health and safety

20

5.

6.

management system is working. Active monitoring involves looking at the premises, plant and substances plus the people, procedures and systems. Reactive monitoring discovers through investigation of accidents and incidents why controls have failed. It is also important to measure the organization against its own long term goals and objectives. Reviewing performance – The results of monitoring and independent audits should be systematically reviewed to evaluate the performance of the management system against the objectives and targets established by the health and safety policy. It is at the review stage that the objectives and targets set in the health and safety policy may be changed. Changes in the health and safety environment in the organization, such as an accident, should also trigger a performance review – this is discussed in more detail in Chapter 2. Performance reviews are not only required by the HSW Act but are part of any organization’s commitment to continuous improvement. Comparisons should be made with internal performance indicators and the external performance indicators of similar organizations with exemplary practices and high standards. Auditing – An independent and structured audit of all parts of the health and safety management system reinforces the review process. Such audits may be internal and external (the differences are discussed in Chapters 7 and 18). The audit assesses compliance with the health and safety management

Health and safety foundations arrangements and procedures. If the audit is to be really effective, it must assess both the compliance with stated procedures and the performance in the workplace. It will identify weaknesses in the health and safety policy and procedures and identify unrealistic or inadequate standards and targets. The conclusions from an audit of an organization’s health and safety performance should be included in the annual report for discussion at Board meetings. This is considered best corporate practice. More detail is given on HSG65 and other health and safety management systems in Chapter 18.

1.17 Practice NEBOSH questions for Chapter 1 1. Explain, using an example EACH case, the meaning of the following terms: (i) ‘hazard’ (ii) ‘risk’ 2. (a) Outline the main functions of: (i) criminal law (ii) civil law (b) Explain the principal differences between common law and statute law. 3. Outline the four key differences between civil law and criminal law. 4. An employer has common law duty of care for the health, safety and welfare of their employees. Giving an example in EACH case, identify what the employer must provide in order to fulﬁll this common law duty of care. 5. (a) Define the term ‘negligence’. (b) Outline the three standard conditions that must be met for an injured employee to prove a case of negligence against his/her employer following an accident at work. (c) Outline the general defences available to an employer in a case of alleged negligence brought by an employee. (d) State the circumstances in which an employer may be held vicariously liable for the negligence of an employee. 6. Explain the meaning of the phrase ‘so far as is reasonable practicable’. 7. State the general and speciﬁc duties of employers to their employees under section 2 of the Health and Safety at Work etc. Act 1974.

8. Outline the general duties placed on employees by: (i) the Health and Safety at Work etc Act 1974 (ii) the Management of Health and Safety at Work Regulations 1999 9. With respect to section 6 of the Health and Safety at Work etc. Act 1974, outline the general duties of designers, manufacturers and supplies of articles and substances for use at work to ensure that they are safe and without risk. 10. With reference to the Management of Health and Safety at Work Regulations 1999: (i) outline the information that an employer must provide to his employees (ii) identify FOUR classes of persons, other than his own employees, to whom an employer must provide health and safety information. (iii) identify the speciﬁc circumstances when health and safety training should be given to employees. 11. Explain the meaning, status and roles of: (i) health and safety regulations (ii) HSC Approved Codes of Practice (iii) HSE guidance 12. Outline, with an example of each, the differences between health and safety regulations and HSC approved codes of practice. 13. Explain the differences between HSC Approved codes of Practice and HSE guidance, giving an example of EACH. 14. List the powers given to inspectors appointed under the Health and Safety at Work etc. Act 1974. 15. (a) Outline FOUR powers available to an inspector when investigating a workplace accident. (b) Identify the two types of enforcement notice that may be served by an inspector, stating the conditions that must be satisﬁed before each type of notice is served. 16. (a) Explain, using a relevant example, the circumstances under which a health and safety inspector may serve an improvement notice. (b) Identify the time period within which an appeal may be lodged against an improvement notice AND state the effect that the appeal will have on the notice. (c) State the penalties for contravening the requirements of an improvement notice when heard BOTH summarily AND on indictment.

21

Introduction to Health and Safety at Work 17. (a) Explain, giving an example in each case, the circumstances under which a health and safety inspector may serve: (i) an improvement notice (ii) a prohibition notice (b) State the effect on each type of enforcement notice of appealing against it. 18. Outline ways in which the Health and Safety Executive can inﬂuence the health and safety performance of an organization. 19. Outline the sources of published information that may be consulted when dealing with a health and safety problem at work. 20. (a) Outline the purpose of employer liability insurance. (b) Outline SIX costs of a workplace accident that might be uninsured. 21. Replacement or repair of damaged equipment is a cost that an organization may incur following an accident at work. List EIGHT other possible costs to the organization following a workplace accident. 22. List EIGHT possible costs to an organization when employees are absent due to work-related ill-health.

22

23. Outline reasons for maintaining good standards of health and safety within an organization. 24. (a) Draw a ﬂowchart to show the relationships between the six elements of the health and safety management model in HSE’s “Successful Health and Safety Management” (HSG65). (b) Outline the part that EACH element of the HSG65 model plays within the health and safety management system. 25. (a) Draw a ﬂowchart to identify the main components of the health and safety management system described in the HSE publication “Successful Health and Safety Management” (HSG65). (b) Outline TWO components of the health and safety management system identiﬁed in (a). 26. Outline the main components of a health and safety management system. 27. Outline the economic beneﬁts that an organization may obtain by implementing a successful health and safety management system.

Policy

2.1 Introduction Every organization should have a clear policy for the management of health and safety so that everybody associated with the organization is aware of its health and safety aims and objectives. For a policy to be effective, it must be honoured in the spirit as well as the letter. A good health and safety policy will also enhance the performance of the organization in areas other than health and safety, help with the personal development of the workforce and reduce ﬁnancial losses.

2.2 Legal requirements Section 2(3) of the Health and Safety at Work Act and the Employers’ Health and Safety Policy Statements

2 (Exception) Regulations 1975 require employers, with ﬁve or more employees, to prepare and revise on a regular basis a written health and safety policy together with the necessary organization and arrangements to carry it out and to bring the statement and any revision of it to the notice of their employees. This does not mean that organizations with four or less employees do not need to have a safety policy – it simply means that it does not have to be written down. The number of employees is the maximum number at any one time whether they are full time, part time or seasonal. This obligation on employers was introduced for the ﬁrst time by the HSW Act and is related to the reliance in the Act on self-regulation by employers to improve health and safety standards rather than on enforcement alone. A good health and safety policy involves the development, monitoring and review of the standards needed to address and reduce the risks to health and safety produced by the organization. The law requires that the written health and safety policy should include the following three sections: ➤ a health and safety policy statement of intent which includes the health and safety aims and objectives of the organization ➤ the health and safety organization detailing the people with health and safety responsibilities and their duties ➤ the health and safety arrangements in place in terms of systems and procedures.

Figure 2.1

Well presented policy documents.

The Management of Health and Safety at Work Regulations also requires the employer to ‘make and give effect to such arrangements as are appropriate, having regard to the nature of his activities and the size of his undertaking,

23

Introduction to Health and Safety at Work for the effective planning, organization, control, monitoring and review of the preventative and protective measures.’ It further requires that these arrangements must be recorded when there are ﬁve or more employees. When an inspector from the HSE or Local Authority visits an establishment, it is very likely that they will wish to see the health and safety policy as an initial indication of the management attitude to health and safety. There have been instances of prosecutions being made due to the absence of a written health and safety policy. (Such cases are, however, usually brought before the courts because of additional concerns.)

2.3 Key elements of a health and safety policy 2.3.1

Policy statement of intent

The health and safety policy statement of intent is often referred to as the health and safety policy statement or simply (and incorrectly) as the health and safety policy. It should contain the aims (which are not measurable) and objectives (which are measurable) of the organization or company. Aims will probably remain unchanged during policy revisions whereas objectives will be reviewed and modiﬁed or changed each year. The statement should be written in clear and simple language so that it is easily understandable. It should also be fairly brief and broken down into a series of smaller statements or bullet points. The statement should be signed and dated by the most senior person in the organization. This will demonstrate management commitment to health and safety and give authority to the policy. It will indicate where ultimate responsibility lies and the frequency with which the policy statement is reviewed.

The policy statement should be written by the organization and not by external consultants since it needs to address the speciﬁc health and safety issues and hazards within the organization. In large organizations, it may be necessary to have health and safety policies for each department and/or site with an overarching general policy incorporating the individual policies. Such an approach is often used by local authorities and multinational companies. The following points should be included or considered when a health and safety policy statement is being drafted: ➤ the aims should cover health and safety, welfare and relevant environmental issues ➤ the position of the senior person in the organization or company who is responsible for health and safety (normally the chief executive) ➤ the names of the Health and Safety Adviser and any safety representatives ➤ a commitment to the basic requirements of the Health and Safety at Work Act (access, egress, risk assessments, safe plant and systems of work, use, handling, transport and handling of articles and substances, information, training and supervision) ➤ a commitment to the additional requirements of the Management of Health and Safety at Work Regulations (risk assessment, emergency procedures, health surveillance and employment of competent persons) ➤ duties towards the wider general public and others (contractors, customers, students, etc.) ➤ the principal hazards in the organization ➤ speciﬁc policies of the organization (e.g. smoking policy, violence to staff, etc.) ➤ a commitment to employee consultation possibly using a safety committee or plant council ➤ duties of employees (particularly those deﬁned in the Management of Health and Safety at Work Regulations) ➤ speciﬁc performance targets for the immediate and long term future. Health and safety performance targets are an important part of the statement of intent because: ➤ they indicate that there is management commitment to improve health and safety performance ➤ they motivate the workforce with tangible goals resulting, perhaps, in individual or collective rewards ➤ they offer evidence during the monitoring, review and audit phases of the management system.

Figure 2.2

24

Part of a policy commitment.

The type of target chosen depends very much on the areas which need the greatest improvement in the

Policy organization. The following list, which is not exhaustive, shows common health and safety performance targets: ➤ a speciﬁc reduction in the number of accidents, incidents and cases of work-related ill-health (perhaps to zero) ➤ a reduction in the level of sickness absence ➤ a speciﬁc increase in the number of employees trained in health and safety ➤ an increase in the reporting of minor accidents and ‘near miss’ incidents ➤ a reduction in the number of civil claims ➤ no enforcement notices from the HSE or Local Authority ➤ a speciﬁc improvement in health and safety audit scores ➤ the achievement of a nationally recognised health and safety management standard, such as OHSAS 18001. The policy statement of intent should be posted on prominent notice boards throughout the workplace and brought to the attention of all employees at induction and refresher training sessions. It can also be communicated to the workforce during team brieﬁng sessions, at ‘toolbox’ talks which are conducted at the workplace or directly by email, intranet, newsletters or booklets. It should be a permanent item on the agenda for health and safety committee meetings where it should be reviewed at each meeting.

2.3.2

➤ employees (responsible for taking reasonable care of the health and safety of themselves and others who may be affected by their acts or omissions) ➤ ﬁre marshals (responsible for the safe evacuation of the building in an emergency) ➤ ﬁrst aiders (responsible for administering ﬁrst aid to injured persons) For smaller organizations, some of the specialists mentioned above may well be employed on a consultancy basis. For the health and safety organization to work successfully, it must be supported from the top (preferably at Board level) and some ﬁnancial resource made available. It is also important that certain key functions are included in the organization structure. These include: ➤ accident investigation and reporting ➤ health and safety training and information ➤ health and safety monitoring and audit

Organization of health and safety

This section of the policy deﬁnes the names, positions and duties of those within the organization or company who have a responsibility for health and safety. Therefore, it identiﬁes those health and safety responsibilities and the reporting lines through the management structure. This section will include the following groups together with their associated responsibilities: ➤ directors and senior managers (responsible for setting policy, objectives and targets) ➤ supervisors (responsible for checking day-to-day compliance with the policy) ➤ safety advisers (responsible for giving advice during accident investigations and on compliance issues) ➤ other specialist, such as an occupational nurse, chemical analyst and an electrician (responsible for giving specialist advice on particular health and safety issues) ➤ safety representatives (responsible for representing employees during consultation meetings on health and safety issues with the employer)

Figure 2.3 Good information, training and working with employees is essential.

25

Introduction to Health and Safety at Work ➤ health surveillance ➤ monitoring of plant and equipment and its maintenance ➤ liaison with external agencies ➤ management and/or employee safety committees – the management committee will monitor day to day problems and any concerns of the employee health and safety committee. The role of the health and safety adviser is to provide specialist information to managers in the organization and to monitor the effectiveness of health and safety procedures. The adviser is not ‘responsible’ for health and safety or its implementation; that is the role of the line managers. Finally the job descriptions, which deﬁne the duties of each person in the health and safety organizational structure, must not contain responsibility overlaps or blur chains of command. Each individual must be clear about his/her responsibilities and the limits of those responsibilities.

2.3.3

Arrangements for Health and Safety

The arrangements section of the health and safety policy gives details of the speciﬁc systems and procedures used to assist in the implementation of the policy statement. This will include health and safety rules and procedures and the provision of facilities such as a ﬁrst aid room and wash rooms. It is common for risk assessments (including COSHH, manual handling and PPE assessments) to be included in the arrangements section particularly for those hazards referred to in the policy statement. It is important that arrangements for ﬁre and other emergencies and for information, instruction, training and supervision are also covered. Local codes of practice (e.g. for fork lift drivers) should be included. The following list covers the more common items normally included in the arrangements section of the health and safety policy: ➤ employee health and safety code of practice ➤ accident and illness reporting and investigation procedures ➤ emergency procedures, ﬁrst aid ➤ procedures for undertaking risk assessments ➤ control of exposure to speciﬁc hazards (noise, vibration, radiation, manual handling, hazardous substances etc.) ➤ machinery safety (including safe systems of work, lifting and pressure equipment) ➤ electrical equipment (maintenance and testing) ➤ maintenance procedures ➤ permits to work procedures ➤ use of personal protective equipment

26

➤ monitoring procedures including health and safety inspections and audits ➤ procedures for the control and safety of contractors and visitors ➤ provision of welfare facilities ➤ training procedures and arrangements ➤ catering and food hygiene procedures ➤ arrangements for consultation with employees ➤ terms of reference and constitution of the safety committee ➤ procedures and arrangements for waste disposal. The three sections of the health and safety policy are usually kept together in a health and safety manual and copies distributed around the organization.

2.4 Review of health and safety policy It is important that the health and safety policy is monitored and reviewed on a regular basis. For this to be successful, a series of benchmarks need to be established. Such benchmarks, or examples of good practice, are deﬁned by comparison with the health and safety performance of other parts of the organization or the national performance of the occupational group of the organization. The Health and Safety Executive publish an annual report, statistics and a bulletins all of which may be used for this purpose. Typical benchmarks include accident rates per employee and accident or disease causation. There are several reasons to review the health and safety policy. The more important reasons are: ➤ signiﬁcant organizational changes have taken place ➤ there have been changes in personnel ➤ there have been changes in legislation ➤ the monitoring of risk assessments or accident/ incident investigations indicate that the health and safety policy is no longer totally effective ➤ enforcement action has been taken by the HSE or Local Authority ➤ a sufﬁcient period of time has elapsed since the previous review. A positive promotion of health and safety performance will achieve far more than simply prevent accidents and ill-health. It will: ➤ support the overall development of personnel ➤ improve communication and consultation throughout the organization ➤ minimize ﬁnancial losses due to accidents and illhealth and other incidents

Policy

Safety, quality and production will receive equal priority Policy Statement View

Figure 2.4

Sound policy but not put into practice–blocked fire exit.

➤ directly involve senior managers in all levels of the organization ➤ improve supervision, particularly for young persons and those on occupational training courses ➤ improve production processes ➤ improve the public image of the organization or company. It is apparent, however, that some health and safety policies appear to be less than successful. There are many reasons for this. The most common are: ➤ the statements in the policy and the health and safety priorities are not understood by or properly communicated to the workforce ➤ minimal resources are made available for the implementation of the policy ➤ too much emphasis on rules for employees and too little on management policy ➤ a lack of parity with other activities of the organization (such as ﬁnance and quality control) due to mistaken concerns about the costs of health and safety and the effect of those costs on overall performance. This attitude produces a poor health and safety culture ➤ lack of senior management involvement in health and safety, particularly at board level ➤ employee concerns that their health and safety issues not being addressed or that they are not receiving adequate health and safety information. This can lead to low morale amongst the workforce and, possibly, high absenteeism

➤ high labour turnover ➤ inadequate personal protective equipment ➤ unsafe and poorly maintained machinery and equipment ➤ a lack of health and safety monitoring procedures. In summary, a successful health and safety policy is likely to lead to a successful organization or company. A checklist for assessing any safety policy has been produced by the HSE and has been reproduced in Appendix 2.1.

2.5 Practice NEBOSH questions for Chapter 2 1. (a) Outline the legal requirements whereby an employer must prepare a written health and safety policy. (b) Identify the three main sections of a health and safety policy document and explain the purpose and general content of each section. 2. (a) State the legal requirements whereby employers must prepare a written statement of their health and safety policy. (b) Outline the various methods for communicating the contents of a health and safety policy to a workforce.

27

Introduction to Health and Safety at Work 3. Explain why a health and safety policy should be signed by the most senior person in an organization, such as a Managing Director or Chief Executive. 4. (a) Identify the typical content of the ‘statement of intent’ section of an organization’s health and safety policy document. (b) Outline the factors that may indicate that health and safety standards within an organization do not reﬂect the objectives within the ‘statement of intent’. 5. Identify the purposes of each of the following sections of a health and safety policy document: (i) ‘statement of intent’ (ii) ‘organization’ (iii) ‘arrangements’. 6. Identify SIX categories of persons who may be shown in the ‘organization’ section of a health and

28

safety policy document AND state their likely general or speciﬁc health and safety responsibilities. 7. Outline the issues that are typically included in the arrangements section of a health and safety document. 8. Outline the key areas that should be addressed in the ‘arrangements’ section of a health and safety policy document. 9. (a) Explain why it is important for an organization to set targets in terms of its health and safety performance (b) Outline SIX types of target that an organization might typically set in relation to health and safety. 10. Outline the circumstances that would require a health and safety policy of be reviewed.

Policy Appendix 2.1 Health and Safety Policy Checklist

The following checklist is intended as an aid to the writing and review of a safety policy. It is derived from the booklet Writing a safety policy statement published by the HSE in booklet HSC 6.

General policy and organization ➤ Does the statement express a commitment to health and safety and are your obligations towards your employees made clear? ➤ Does it say which senior manager is responsible for seeing that it is implemented and for keeping it under review, and how this will be done? ➤ Is it signed and dated by you or a partner or senior director? ➤ Have the views of managers and supervisors, safety representatives and of the safety committee been taken into account? ➤ Were the duties set out in the statement discussed with the people concerned in advance, and accepted by them, and do they understand how their performance is to be assessed and what resources they have at their disposal? ➤ Does the statement make clear that co-operation on the part of all employees is vital to the success of your health and safety policy? ➤ Does it say how employees are to be involved in health and safety matters, for example, by being consulted, by taking part in inspections, and by sitting on a safety committee? ➤ Does it show clearly how the duties for health and safety are allocated and are the responsibilities at different levels described?

Figure 2.5

Emergency procedures.

➤ Does it say who is responsible for the following matters (including deputies where appropriate)? – reporting investigations and recording accidents – ﬁre precautions, ﬁre drill, evacuation procedures – ﬁrst aid – safety inspections – the training programme – ensuring that legal requirements are met, for example, regular testing of lifts and notifying accidents to the health and safety inspector.

Arrangements that need to be considered ➤ Keeping the workplace, including staircases, ﬂoors, ways in and out, washrooms, etc. in a safe and clean condition by cleaning, maintenance and repair ➤ The requirements of the Work at Height Regulations ➤ Any suitable and sufﬁcient risk assessments.

Plant and substances ➤ Maintenance of equipment such as tools, ladders, etc. Are they in a safe condition? ➤ Maintenance and proper use of safety equipment such as helmets, boots, goggles, respirators, etc. ➤ Maintenance and proper use of plant, machinery and guards. ➤ Regular testing and maintenance of lifts, hoists, cranes, pressure systems, boilers and other dangerous machinery, emergency repair work, and safe methods of doing it.

Figure 2.6

Responsibilities.

29

Introduction to Health and Safety at Work

operators or operators under instruction (which should deal fully with safety aspects).

Emergencies ➤ Ensuring that ﬁre exits are marked, unlocked and free from obstruction ➤ Maintenance and testing of ﬁre-ﬁghting equipment, ﬁre drills and evacuation procedures ➤ First aid, including name and location of person responsible for ﬁrst aid and deputy, and location of ﬁrst aid box.

Communication Figure 2.7

Fork lift truck.

➤ Maintenance of electrical installations and equipment. ➤ Safe storage, handling and, where applicable, packaging, labelling and transport of dangerous substances. ➤ Controls of work involving harmful substances such as lead and asbestos. ➤ The introduction of new plant, equipment or substances into the workplace by examination, testing and consultation with the workforce.

➤ Giving your employees information about the general duties under the Health and Safety at Work Act and speciﬁc legal requirements relating to their work. ➤ Giving employees necessary information about substances, plant, machinery, and equipment with which they come into contact. ➤ Discussing with contractors, before they come on site, how they plan to do their job, whether they need any equipment from your organization to help them, whether they can operate either in a segregated area or only when part of the plant is shut down and, if not, what hazards they may create for your employees and vice versa.

Other hazards ➤ Noise problems – wearing of hearing protection, and control of noise at source ➤ Vibration problems – hand-arm and whole-body control techniques and personal protection ➤ Preventing unnecessary or unauthorized entry into hazardous areas ➤ Lifting of heavy or awkward loads ➤ Protecting the safety of employees against assault when handling or transporting the employer’s money or valuables ➤ Special hazards to employees when working on unfamiliar sites, including discussion with site manager where necessary ➤ Control of works transport, e.g. fork lift trucks by restricting use to experienced and authorized

30

Training ➤ Training employees, supervisors and managers to enable them to work safely and to carry out their health and safety responsibilities efﬁciently.

Supervising ➤ Supervising employees so far as necessary for their safety – especially young workers, new employees and employees carrying out unfamiliar tasks.

Keeping Check ➤ Regular inspections and checks of the workplace, machinery appliances and working methods.

Organizing for health and safety

3.1 Introduction This chapter is about managers in businesses, or other organizations, setting out clear responsibilities and lines of communications for everyone in the enterprise. The chapter also covers the legal responsibilities that exist between people who control premises and those who use them; between contractors and those who hire them; and the duties of suppliers, manufacturers and designers of articles and substances for use at work. Chapter 2 is concerned with policy, which is an essential ﬁrst step. The policy will only remain as words on paper, however good the intentions, until there is an effective organization set up to implement and monitor its requirements.

PLC Director

3

The policy sets the direction for health and safety within the enterprise and forms the written intentions of the principals or directors of the business. The organization needs to be clearly communicated and people need to know what they are responsible for in the day-to-day operations. A vague statement that ‘everyone is responsible for health and safety’ is misleading and fudges the real issues. Everyone is responsible but management in particular. There is no equality of responsibility under law between those who provide direction and create policy and those who are employed to follow. Principals, or employers in terms of the HSW Act, have substantially more responsibility than employees. Some policies are written so that most of the wording concerns strict requirements laid on employees and only a few vague words cover managers’ responsibilities. Generally, such policies do not meet the HSW Act or the Management of Health and Safety at Work Regulations 1999, which require an effective policy with a robust organization and arrangements to be set up.

Divisional Director

3.2 Control Site Manager

Deputy Manager

Senior Supervisor

Figure 3.1 Everyone from senior managers down has health and safety responsibilities.

Like all management functions, establishing control and maintaining it day in day out is crucial to effective health and safety management. Managers, particularly at senior levels, must take proactive responsibility for controlling issues that could lead to ill-health, injury or loss. A nominated senior manager at the top of the organization needs to oversee policy implementation and monitoring. The nominated person will need to report regularly to the most senior management team and will be a director or principal of the organization.

31

Introduction to Health and Safety at Work Health and safety responsibilities will need to be assigned to line managers and expertise must be available, either inside or outside the enterprise, to help them achieve the requirements of the HSW Act and the regulations made under the Act. The purpose of the health and safety organization is to harness the collective enthusiasm, skills and effort of the entire workforce with managers taking key responsibility and providing clear direction. The prevention of accidents and ill-health through management systems of control becomes the focus rather than looking for individuals to blame after the incident occurs. The control arrangements should be part of the written health and safety policy. Performance standards will need to be agreed and objectives set which link the outputs required to speciﬁc tasks and activities for which individuals are responsible. For example, the objective could be to carry out a workplace inspection once a week to an agreed checklist and rectify faults within three working days. The periodic, say annual, audit would check to see if this was being achieved and if not the reasons for non-compliance with the objective. People should be held accountable for achieving the agreed objectives through existing or normal procedures such as: ➤ job descriptions, which include health and safety responsibilities ➤ performance appraisal systems, which look at individual contributions ➤ arrangements for dealing with poor performance ➤ where justiﬁed, the use of disciplinary procedures. Such arrangements are only effective if health and safety issues achieve the same degree of importance as other key management concerns and a good performance is considered to be an essential part of the career and personal development.

3.3 Employers’ responsibilities Employers have duties under both criminal and civil law. The civil law duties are covered in Chapter 1. The general duties of employers under HSW Act relate to: ➤ the health, safety and welfare at work of employees and other workers, whether part-time, casual, temporary, homeworkers, on work experience, Government Training Schemes or on site as contractors – i.e. anyone working under their control or direction ➤ the health and safety of anyone who visits or uses the workplace ➤ the health and safety of anyone who is allowed to use the organization’s equipment

32

➤ the health and safety of those affected by the work activity, for example neighbours, and the general public. Other duties on employers are covered in Chapter 1 and the summary of the HSW Act in Chapter 17.

3.4 Employees’ responsibilities Employees have speciﬁc responsibilities under the HSW Act, which are: ➤ to take reasonable care for the health and safety of themselves and of other persons who may be affected by their acts or omissions at work. This involves the same wide group that the employer has to cover, not just the people on the next desk or bench ➤ to cooperate with employers in assisting them to fulﬁl their statutory duties ➤ not to interfere with deliberately or misuse anything provided, in accordance with health and safety legislation, to further health and safety at work.

3.5 Organizational health and safety responsibilities In addition to the legal responsibilities on management, there are many speciﬁc responsibilities imposed by each organization’s health and safety policy. Appendix 3.1 to this chapter shows a typical summary of the health and safety responsibilities and accountability of each level of the line organization to provide an understanding of how health and safety responsibilities and accountability are integrated within the total organization. The responsibilities cover directors, senior managers, site managers, department managers, supervisors and employees. Many organizations will not ﬁt this exact structure but most will have those who direct, those who manage or supervise and those who have no line responsibility but have responsibilities to themselves and fellow workers. Because of the special role and importance of directors, these are covered here in detail.

3.5.1

Directors’ responsibilities

The Chairman of the Health and Safety Commission said at the launch of the guidance on Directors’ responsibilities: Health and safety is a boardroom issue. Good health and safety reflects strong leadership from the top and that is what we want

Organizing for health and safety to see. The company whose chairperson or chief executive is the champion of health and safety sends the kind of message which delivers good performance on the ground. Those who are at the top have a key role to play, which is why boards are being asked to nominate one of their members to be a ‘health and safety’ director. But appointing a health and safety director or department does not absolve the Board from its collective responsibility to lead and oversee health and safety management. Directors’ Responsibility for Health & Safety INDG 343, sets out the following action points for directors: ➤ the Board needs to accept formally and publicly its collective role in providing health and safety leadership in its organization ➤ each member of the Board needs to accept their individual role in providing health and safety leadership for their organization ➤ the Board needs to ensure that all board decisions reﬂect its health and safety intentions, as articulated in the health and safety policy statement. It is important for boards to remember that, although health and safety functions can (and should) be delegated, legal responsibility for health and safety rests with the employer ➤ the Board needs to recognize its role in engaging the active participation of workers in improving health and safety ➤ the Board needs to ensure that it is kept informed of, and alert to, relevant health and safety risk management issues. The Health and Safety Commission recommends that boards appoint one of their number to be the ‘Health and Safety Director’. Directors need to ensure that the Board’s health and safety responsibilities are properly discharged. The Board will need to: ➤ carry out an annual review of health and safety performance ➤ keep the health and safety policy statement up to date with current board priorities and review the policy at least every year ➤ ensure that there are effective management systems for monitoring and reporting on the organization’s health and safety performance ➤ ensure that any signiﬁcant health and safety failures and their investigation are communicated to board members ➤ ensure that when decisions are made the health and safety implications are fully considered

➤ ensure that regular audits are carried out to check that effective health and safety risk management systems are in place. By appointing a ‘Health and Safety Director’ there will be a board member who can ensure that these health and safety risk management issues are properly addressed, both by the Board and more widely throughout the organization. The Chairman and/or Chief Executive have a critical role to play in ensuring risks are properly managed and that the Health and Safety Director has the necessary competence, resources and support of other board members to carry out their functions. Indeed, some boards may prefer to see all the health and safety functions assigned to their Chairman and/or Chief Executive. As long as there is clarity about the health and safety responsibilities and functions, and the Board properly addresses the issues, this is acceptable. The health and safety responsibilities of all board members should be clearly articulated in the organization’s statement of health and safety policy and arrangements. It is important that the role of the Health and Safety Director should not detract either from the responsibilities of other directors for speciﬁc areas of health and safety risk management or from the health and safety responsibilities of the Board as a whole.

3.6 Role and functions of health and safety and other advisers 3.6.1

Competent person

One or more competent persons must be appointed to help managers comply with their duties under health and safety law. The essential point is that managers should have access to expertise to help them fulﬁl the legal requirements. However, they will always remain as advisers and do not assume responsibility in law for health and safety matters. This responsibility always remains with line managers and cannot be delegated to an adviser whether inside or outside the organization. The appointee could be: ➤ the employers themselves if they are sure they know enough about what to do. This may be appropriate in a small low hazard business ➤ one or more employees, as long as they have sufﬁcient time and other resources to do the task properly ➤ someone from outside the organization who has sufﬁcient expertise to help. The HSE have produced two leaﬂets entitled Need help on health and safety? Guidance for employers on when

33

Introduction to Health and Safety at Work representatives with authority and independence. They need to be able to advise on:

Figure 3.2

Safety practitioner at the front line.

and how to get advice on health and safety (INDG 322) and Selecting a Health & Safety Consultancy. If an employer decides to seek outside help they have to ensure that no employees are competent to assist. Many health and safety issues can be tackled by people with an understanding of current best practice and an ability to judge and solve problems. Some help is needed long term, others for a one-off short period. There are a wide range of experts available for different types of health and safety problem. For example: ➤ engineers for specialist ventilation or chemical processes ➤ occupational hygienists for assessment and practical advice on exposure to chemical (dust, gases, fumes, etc.), biological (viruses, fungi, etc.) and physical (noise, vibration, etc.) agents ➤ occupational health professionals for medical examinations and diagnosis of work-related disease, pre-employment and sickness advice, health education, etc. ➤ ergonomists for advice on suitability of equipment, comfort, physical work environment, work organization, etc. ➤ physiotherapists for treatment and prevention of musculoskeletal disorders, etc. ➤ radiation protection advisers for advice on compliance with the Ionising Radiation Regulations 1999 ➤ health and safety practitioner for general advice on implementation of legislation, health and safety management, risk assessment, control measures and monitoring performance, etc.

3.6.2

Health and safety adviser

Status and competence are essential to the role of health and safety and other advisers. They must be able to advise management and employees or their

34

➤ creating and developing health and safety policies. These will be for existing activities plus new acquisitions or processes ➤ the promotion of a positive health and safety culture. This includes helping managers to ensure that an effective health and safety policy is implemented ➤ health and safety planning. This will include goalsetting, deciding priorities and establishing adequate systems and performance standards. Short- and long-term objectives need to be realistic ➤ day-to-day implementation and monitoring of policy and plans. This will include accident and incident investigation, reporting and analysis ➤ performance reviews and audit of the whole health and safety management system.

3.6.3

To do this properly, health and safety advisers need to

➤ have proper training and be suitably qualiﬁed – e.g. NEBOSH Diploma or competence based IOSH membership, relevant degree and, where appropriate, a Chartered Safety and Health Practioner. NEBOSH Certiﬁcate in small to medium-sized low hazard premises, like ofﬁces and retail stores ➤ keep up-to-date information systems on such topics as civil and criminal law, health and safety management and technical advances ➤ know how to interpret the law as it applies to their own organization ➤ actively participate in the establishment of organizational arrangements, systems and risk control standards relating to hardware and human performance. Health and safety advisers will need to work with management on matters such as legal and technical standards ➤ undertake the development and maintenance of procedures for reporting, investigating, recording and analysing accidents and incidents ➤ develop and maintain procedures to ensure that senior managers get a true picture of how well health and safety is being managed (where a benchmarking role may be especially valuable). This will include monitoring, review and auditing ➤ be able to present their advice independently and effectively.

3.6.4

Relationships within the organization

Health and safety advisers: ➤ support the provision of authoritative and independent advice;

Organizing for health and safety ➤ report directly to directors on matters of policy and have the authority to stop work if it contravenes agreed standards and puts people at risk of injury; ➤ are responsible for professional standards and systems. They may also have line management responsibility for other health and safety professionals, in a large group of companies or on a large and/or highhazard site.

reasonable in their position to ensure that there are no risks to the health and safety of people who are not employees but use the premises. This duty extends to:

3.6.5

Those in control of premises are required to take a range of steps depending on the likely use of the premises and the extent of their control and knowledge of the actual use of the premises. Persons in control of premises must also prevent harmful emissions into the atmosphere under section 5 of the HSW Act, but this has been repealed (Subject to Commencement Order) by the Environmental Protection Act 1990. In the interim period any action for emissions is likely to be under the 1990 Act and not the HSW Act.

Relationships outside the organization

Health and safety advisers also have a function outside their own organization. They provide the point of liaison with a number of other agencies including the following: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

environmental health ofﬁcers and licensing ofﬁcials architects and consultants HSE and the Fire Authorities the police HM Coroner or the Procurator Fiscal local authorities insurance companies contractors clients and customers the public equipment suppliers the media general practitioners IOSH and occupational health specialists and services.

3.7 Persons in control of premises Section 4 of the HSW Act requires that ‘Persons in control of non-domestic premises’ take such steps as are

Figure 3.3

➤ people entering the premises to work ➤ people entering the premises to use machinery or equipment, for example, a launderette ➤ access and exit from the premises ➤ corridors, stairs, lifts and storage areas.

3.8 Self-employed The duties of the self-employed under the HSW Act are fairly limited. The Revitalising Health and Safety Strategy document expressed concern about whether the HSW Act sufﬁciently covers the area, in view of the huge growth in the use of contractors and sub-contractors throughout the UK. At December 2001 they are still being reviewed to consider how adjustments should be made. Under the HSW Act the self-employed are: ➤ responsible for their own health and safety ➤ responsible to ensure that others who may be affected are not exposed to risks to their health and safety.

NEBOSH is in control here.

35

Introduction to Health and Safety at Work These responsibilities are extended by the Management of Health and Safety at Work Regulations 1999, which requires self-employed people to: ➤ carry out risk assessment ➤ cooperate with other people who work in the premises and, where necessary, in the appointment of a health and safety coordinator ➤ provide comprehensible information to other peoples’ employees working in their undertaking.

3.9 The supply chain 3.9.1

Introduction

Market leaders in every industry are increasing their grip on the chain of supply. They do so by monitoring rather than managing, and also by working more closely with suppliers. The result of this may be that suppliers or contractors are absorbed into the culture of the dominant ﬁrm, while avoiding the costs and liabilities of actual management. Powerful procurement departments emerge, to deﬁne and impose the necessary quality standards and guard the lists of preferred suppliers. The trend in many manufacturing businesses is to involve suppliers in a greater part of the manufacturing process so that much of the ﬁnal production is the assembly of pre-fabricated subassemblies. This is particularly true of the automotive and aircraft industries. This is good practice as it: ➤ involves the supplier in the design process ➤ reduces the number of items being managed within the business ➤ reduces the number of suppliers ➤ improves quality management by placing the onus on suppliers to deliver fully checked and tested components and systems. In retail, suppliers are even given access to daily sales and forecasts of demand which would normally be considered as highly conﬁdential information. In the process, the freedom of local operating managers to pick and choose suppliers is reduced. Even though the responsibility to do so is often retained, it is strongly qualiﬁed by centrally imposed rules and lists, and assistance or oversight. Suppliers have to be:

In these conditions, suppliers and contractors looking for business with major ﬁrms need greater ﬂexibility and wider competence than previously. This often implies increased size and perhaps mergers, though in principle bids could be, and perhaps are, made by loose partnerships of smaller ﬁrms organized to secure such business.

3.9.2

Advantages of good supply chain management

(a) Reduction of waste This is an important objective of any business and involves not only waste of materials but also time-related waste. Examples of waste are: ➤ unwanted materials due to over ordering, damage or incorrect speciﬁcations ➤ extraneous activities like double handling, for example between manufacturer, builders merchant and the site ➤ re-working re-ﬁtting due to poor quality, design, storage or manufacture ➤ time waste such as waiting for supplies due to excessive time from ordering to delivery or early delivery long before they are needed. (b) Faster reaction A well managed supply chain should be able to respond rapidly to changing requirements. Winter conditions require very different materials than during warmer or drier seasons. A contractor may have to modify plans rapidly and suppliers may need to ramp up or change production at short notice.

Customer

Supplies work, information, car, limits on cost

Supplies payment

Supplies invoice keys, car, report

Service Reception

Supplies car, keys, information on work done and problems

Supplies job sheet, car

Supplies parts as requested Parts Department

Fitter

➤ trusted ➤ treated with fairness in a partnership ➤ given full information to meet the demands being placed on them.

36

Supplies request for parts and consumables

Figure 3.4

Typical supply chain.

Organizing for health and safety (c) Reduction in accidents A closer relationship between client, designers, principal contractors, and suppliers of services and products can result not only in a safer ﬁnished product but, in construction, a safer method of erection. If more products are pre-assembled in ideal factory conditions and then ﬁxed in place on site it is often safer than utilizing a full assembly approach in poor weather conditions on temporary work platforms. Examples are made-up roof trusses and prefabricated doors and windows already ﬁtted to their frames.

3.9.3

Legislation

The HSW Act Section 6 places a duty on everyone in the supply chain, from the designer to the ﬁnal installer, of articles of plant or equipment for use at work or any article of fairground equipment to: ➤ ensure that the article will be safe and without risk to health at all time when it is being set, used, cleaned or maintained ➤ carry out any necessary testing and examination to ensure that it will be safe, and ➤ provide adequate information about its safe setting, use, cleaning, maintenance, dismantling and disposal. There is an obligation on designers or manufacturers to do any research necessary to prove safety in use. Erectors or installers have special responsibilities to make sure, when handed over, that the plant or equipment is safe to use. Similar duties are placed on manufacturers and suppliers of substances for use at work to ensure that the substance is safe when properly used, handled, processed, stored or transported, to provide adequate information and do any necessary research, testing or examining. Where articles or substances are imported, the suppliers’ obligations outlined above attach to the importer, whether a separate importing business or the user personally. Often items are obtained through hire purchase, leasing or other ﬁnancing arrangements with the ownership of the items being vested with the ﬁnancing organization. Where the ﬁnancing organization’s only function is to provide the money to pay for the goods, the supplier’s obligations do not attach to them.

3.9.4

Information for customers

The quality movement has drawn attention to the need to ensure that there are processes in place which ensure

quality, rather than just inspecting and removing defects when it is too late. In much the same way, organizations need to manage health and safety rather than acting when it is too late. Customers need information and speciﬁcations from the manufacturer or supplier – especially where there is a potential risk involved for them. When deciding what the supplier needs to pass on, careful thought is required about the health and safety factors associated with any product or service. This means focusing on four key questions and then framing the information supplied so that it deals with each one. The questions are: ➤ are there any inherent dangers in the product or service being passed on – what could go wrong? ➤ what can the manufacturer or supplier do while working on the product or service to reduce the chance of anything going wrong later? ➤ what can be done at the point of handover to limit the chances of anything going wrong? ➤ what steps should customers take to reduce the chances of something going wrong? What precisely would they need to know? Depending on what is being provided to customers, the customer information may need to comply with the following legislation: ➤ Supply of Machinery (Safety) Regulations 1992 and amendment 1994 ➤ Provision and Use of Work Equipment Regulations 1998 ➤ Control of Substances Hazardous to Health Regulations 2002 ➤ Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 & 2005 amendments. This list is not exhaustive.

3.9.5

Buying problems

Examples of problems that may arise when purchasing include: ➤ second-hand equipment which does not conform to current safety standards ➤ starting to use new substances which do not have safety data sheets ➤ machinery which, while well guarded for operators, may pose risks for a maintenance engineer ➤ ofﬁce chairs which do not provide adequate back support. A risk assessment should be done on any new product, taking into account the likely life expectancy (e.g. delivery,

37

Introduction to Health and Safety at Work ➤ they must provide adequate health and safety information, instructions, training and supervision for operators. Manufacturers and suppliers are required by law to provide information that will enable safe use of the equipment, substances, etc. and without risk to health. Some of the issues that will need to be considered when buying in product or plant include:

Figure 3.5 Inadequate chair – take care when buying second-hand.

installation, use, cleaning, maintenance, disposal, etc). The supplier should be able to provide the information needed to do this. This will help the purchaser make an informed decision on the total costs because the risks will have been identiﬁed as will the precautions needed to control those risks. A risk assessment will still be needed for a CE-marked product. The CE marking signiﬁes the manufacturer’s declaration that the product conforms to relevant European Directives. Declarations from reputable manufacturers will normally be reliable. However, purchasers should be alert to fake or inadequate declarations and technical standards which may affect the health and safety of the product despite the CE marking. The risk assessment is still necessary to consider how and where the product will be used, what effect it might have on existing operations and what training will be required. Employers have some key duties when buying plant and equipment: ➤ they must ensure that work equipment is safe, suitable for its purpose and complies with the relevant legislation. This applies equally to equipment which is adapted to be used in ways for which it was not originally designed ➤ when selecting work equipment, they must consider existing working conditions and health and safety issues

38

➤ ergonomics – risk of work-related upper limb disorders (WRULD) ➤ manual handling needs ➤ access/egress ➤ storage, e.g. of chemicals ➤ risk to contractors when decommissioning old plant or installing new plant ➤ hazardous materials – provision of extraction equipment or personal protective equipment ➤ waste disposal ➤ safe systems of work ➤ training ➤ machinery guarding ➤ emissions from equipment/plant, such as noise, heat or vibration.

3.10 Contractors 3.10.1

Introduction

The use of contractors is increasing as many companies turn to outside resources to supplement their own staff and expertise. A contractor is anyone who is brought in to work who is not an employee. Contractors are used for maintenance, repairs, installation, construction, demolition, computer work, cleaning, security, health and safety and many other tasks. Sometimes there are several contractors on site at any one time. Clients need to think about how their work may affect each other and how they interact with the normal site occupier.

3.10.2

Legal considerations

The HSW Act applies to all work activities. It requires employers to ensure, so far as is reasonably practicable, the health and safety of: ➤ their employees ➤ other people at work on their site, including contractors ➤ members of the public who may be affected by their work.

Organizing for health and safety ➤ setting up emergency procedures ➤ providing training ➤ cooperating with others on health and safety matters, for example, contractors who share the site with an occupier ➤ providing temporary workers such as contractors, with health and safety information.

Figure 3.6

Contractors at work.

All parties to a contract have speciﬁc responsibilities under health and safety law, and these cannot be passed on to someone else: ➤ employers are responsible for protecting people from harm caused by work activities. This includes the responsibility not to harm contractors and subcontractors on site ➤ employees and contractors have to take care not to endanger themselves, their colleagues or others affected by their work ➤ contractors also have to comply with the HSW Act and other health and safety legislations. Clearly, when contractors are engaged, the activities of different employers do interact. So cooperation and communication are needed to make sure all parties can meet their obligations ➤ employees have to cooperate with their employer on health and safety matters, and not do anything that puts them or others at risk ➤ employees must be trained and clearly instructed in their duties ➤ self-employed people must not put themselves in danger, or others who may be affected by what they do ➤ suppliers of chemicals, machinery and equipment have to make sure their products or imports are safe, and provide information on this. The Management of Health and Safety at Work Regulations apply to everyone at work and encourage employers to take a more systematic approach to dealing with health and safety by: ➤ assessing the risks which affect employees and anyone who might be affected by the site occupier’s work, including contractors

The principles of cooperation, coordination and communication between organizations underpin the Management of Health and Safety at Work Regulations and the CDM Regulations, explained next. See later section 3.11 on joint occupation of premises. For more information on the Management of Health and Safety at Work Regulations, read the summary in Chapter 17.

3.10.3

Construction Design and Management (CDM2007) Regulations

Businesses often engage contractors for construction projects at one time or another to build plant, convert or extend premises and demolish buildings. The CDM2007 regulations apply to all construction projects. Larger projects which are notiﬁable, (see details in Chapters 16 and 17) have more extensive requirements. All projects require: ➤ non-domestic clients to check the competence of all their appointees; ensure there are suitable management arrangements for the project; allow sufﬁcient time and resources for all stages; provide preconstruction information to designers and contractors ➤ designers to eliminate hazards and reduce risks during design; and provide information about remaining risks ➤ contractors to plan, manage and monitor their own work and that of workers; check the competence of all their appointees and workers; train their own employees; provide information to their workers; comply with the requirements for health and safety on site detailed in Part 4 of the Regulations and other regulations such as the Work at Height Regulations; and ensure there are adequate welfare facilities for their workers ➤ everyone to assure their own competence; co-operate with others and co-ordinate work so as to ensure the health and safety of construction workers and others who may be affected by the work; report obvious risks; take account of the general principles of prevention in planning or carrying out construction work; and comply with the requirements in Schedule 3, Part 4 of CDM2007 and other regulations for any work under their control.

39

Introduction to Health and Safety at Work For even small projects clients should ensure that contractors provide: (a) information regarding the contractor’s Health & Safety policy (b) the contractor’s health and safety organization detailing the responsibilities of individuals (c) information on the contractor’s procedures and standards of safe working (d) the method statements for the project in hand (e) details on how the contractor will audit and implement their health and safety procedures. Smaller contractors may need some guidance to help them produce suitable method statements. While they do not need to be lengthy they should set out those features essential to safe working, e.g. access arrangements, personal protective equipment, control of chemical risks, etc. Copies of relevant risk assessments for the work to be undertaken should be requested. These need not be very detailed but should indicate the risk and the control methods to be used. The Client, Designer, CDM Coordinator, Principal Contractor and other Contractors all have speciﬁc roles under CDM 2007 Regulations. For more information see Chapter 16 on Construction and Chapter 17 on the Summary of Legislation.

3.10.4

Contractor selection

The selection of the right contractor for a particular job is probably the most important element in ensuring that the risks to the health and safety of everybody involved on the activity and people in the vicinity are reduced as far as possible. Ideally, selection should be made from a list of approved contractors who have demonstrated that they are able to meet the client’s requirements. The selection of a contractor has to be a balanced judgement with a number of factors taken into account. Fortunately, a contractor who works well and meets the client’s requirements in terms of the quality and timeliness of the work is likely also to have a better than average health and safety performance. Cost, of course, will have to be part of the judgement but may not provide any indication of which contractor is likely to give the best performance in health and safety terms. In deciding which contractor should be chosen for a task, the following should be considered: ➤ Do they have an adequate health and safety policy? ➤ Can they demonstrate that the person responsible for the work is competent? ➤ Can they demonstrate that competent safety advice will be available?

40

➤ Do they monitor the level of accidents at their work site? ➤ Do they have a system to assess the hazards of a job and implement appropriate control measures? ➤ Will they produce a method statement, which sets out how they will deal with all signiﬁcant risks? ➤ Do they have guidance on health and safety arrangements and procedures to be followed? ➤ Do they have effective monitoring arrangements? ➤ Do they use trained and skilled staff who are qualiﬁed where appropriate? (Judgement will be required, as many construction workers have had little or no training except training on the job.) Can the company demonstrate that the employees or other workers used for the job have had the appropriate training and are properly experienced and, where appropriate, qualiﬁed? ➤ Can they produce good references indicating satisfactory performance?

3.10.5

Contractor authorization

Contractors, their employees, sub-contractors and their employees, should not be allowed to commence work on any client’s site without authorization signed by the Company contact. The authorization should clearly deﬁne the range of work that the contractor can carry out and set down any special requirements, for example, protective clothing, ﬁre exits to be left clear, isolation arrangements, etc. Permits will be required for operations such as hot work, etc. All contractors should keep a copy of their authorization at the place of work. A second copy of the authorization should be kept at the site and be available for inspection. The Company contact signing the authorization will be responsible for all aspects of the work of the contractor. The contact will need to check as a minimum the following: ➤ that the correct contractor for the work has been selected ➤ that the contractor has made appropriate arrangements for supervision of staff ➤ that the contractor has received and signed for a copy of the contractor’s safety rules ➤ that the contractor is clear what is required, the limits of the work and any special precautions that need to be taken ➤ that the contractor’s personnel are properly qualiﬁed for the work to be undertaken. The Company contact should check whether subcontractors will be used. They will also require authorization, if deemed acceptable. It will be the responsibility of the

Organizing for health and safety Company contact to ensure that sub-contractors are properly supervised. Appropriate supervision will depend on a number of factors, including the risk associated with the job, experience of the contractor and the amount of supervision the contractor will provide. The responsibility for ensuring there is proper supervision lies with the person signing the contractor’s authorization. The Company contact will be responsible for ensuring that there is adequate and clear communication between different contractors and Company personnel where this is appropriate.

3.10.6

Safety rules for contractors

In the conditions of contract there should be a stipulation that the contractor and all of their employees adhere to the contractor’s safety rules. Contractor’s safety rules should contain as a minimum the following points: ➤ health & safety: that the contractor operates to at least the minimum legal standard and conforms to accepted industry good practice ➤ supervision: that the contractor provides a good standard of supervision of their own employees ➤ sub-contractors: that they may not use subcontractors without prior written agreement from the Company ➤ authorization: that each employee must carry an authorization card issued by the Company at all times while on site.

3.10.7

Example of rules for contractors

Contractors engaged by the organization to carry out work on its premises will: ➤ familiarize themselves with so much of the organization’s safety policy as affects them and will ensure that appropriate parts of the policy are communicated to their employees, and any sub-contractors and employees of sub-contractors who will do work on the premises ➤ cooperate with the organization in its fulﬁlment of its health and safety duties to contractors and take the necessary steps to ensure the like cooperation of their employees ➤ comply with their legal and moral health, safety and food hygiene duties ➤ ensure the carrying out of their work on the organization’s premises in such a manner as not to put either themselves or any other persons on or about the premises at risk ➤ where they wish to avail themselves of the organization’s ﬁrst aid arrangements/facilities while on

the premises, ensure that written agreement to this effect is obtained prior to ﬁrst commencement of work on the premises ➤ where applicable and requested by the organization, supply a copy of its statement of policy, organization and arrangements for health and safety written for the purposes of compliance with The Management of Health and Safety at Work Regulations and Section 2(3) of the Health and Safety at Work Act 1974 ➤ abide by all relevant provisions of the organization’s safety policy, including compliance with health and safety rules and CDM 2007 ➤ ensure that on arrival at the premises, they and any other persons who are to do work under the contract report to reception or their designated organization contact. Without prejudice to the requirements stated above, contractors, sub-contractors and employees of contractors and sub-contractors will, to the extent that such matters are within their control, ensure: ➤ the safe handling, storage and disposal of materials brought onto the premises ➤ that the organization is informed of any hazardous substances brought onto the premises and that the relevant parts of the Control of Substances Hazardous to Health Regulations in relation thereto are complied with ➤ that ﬁre prevention and ﬁre precaution measures are taken in the use of equipment which could cause ﬁres ➤ that steps are taken to minimize noise and vibration produced by their equipment and activities ➤ that scaffolds, ladders and other such means of access, where required, are erected and used in accordance with Work at Height Regulations and good working practice ➤ that any welding or burning equipment brought onto the premises is in safe operating condition and used in accordance with all safety requirements ➤ that any lifting equipment brought onto the premises is adequate for the task and has been properly tested/certiﬁed ➤ that any plant and equipment brought onto the premises is in safe condition and used/operated by competent persons ➤ that for vehicles brought onto the premises, any speed, condition or parking restrictions are observed ➤ that compliance is made with the relevant requirements of the Electricity at Work Regulations 1989 ➤ that connection(s) to the organization’s electricity supply is from a point speciﬁed by its management and is by proper connectors and cables

41

Introduction to Health and Safety at Work ➤ that they are familiar with emergency procedures existing on the premises ➤ that welfare facilities provided by the organization are treated with care and respect ➤ that access to restricted parts of the premises is observed and the requirements of food safety legislation are complied with ➤ that any major or lost-time accident or dangerous occurrence on the organization’s premises is reported as soon as possible to their site contact ➤ that where any doubt exists regarding health and safety requirements, advice is sought from the site contact. The foregoing requirements do not exempt contractors from their statutory duties in relation to health and safety, but are intended to assist them in attaining a high standard of compliance with those duties.

3.11 Joint occupation of premises The Management of Health and Safety at Work Regulations speciﬁcally states that where two or more employers share a workplace – whether on a temporary or a permanent basis – each employer shall: ➤ cooperate with other employers ➤ take reasonable steps to coordinate between other employers to comply with legal requirements ➤ take reasonable steps to inform other employers where there are risks to health and safety. All employers and self-employed people involved should satisfy themselves that the arrangements adopted are adequate. Where a particular employer controls the premises, the other employers should help to assess the shared risks and coordinate any necessary control procedures. Where there is no controlling employer the organizations present should agree joint arrangements to meet regulatory obligations, such as appointing a health and safety coordinator.

3.12 Cooperation with the workforce It is important to gain the cooperation of all employees if a successful health and safety culture is to become established. This cooperation is best achieved by consultation. The easiest and potentially the most effective method of consultation is the health and safety committee. It will realize its full potential if its recommendations are seen to be implemented and both management and

42

employee concerns are freely discussed. It will not be so successful if it is seen as a talking shop. The committee should have stated objectives, which mirror the objectives in the organization’s health and safety policy statement, and its own terms of reference. Terms of reference could include the following: ➤ the study of accident and notiﬁable disease statistics to enable reports to be made of recommended remedial actions ➤ the examination of health and safety audit and statutory inspection reports ➤ the consideration of reports from the external enforcement agency ➤ the review of new legislation, approved codes of practice and guidance and its effect on the organization ➤ the monitoring and review of all health and safety training and instruction activities in the organization ➤ the monitoring and review of health and safety publicity and communication throughout the organization. There are no ﬁxed rules on the composition of the health and safety committee except that it should be representative of the whole organization. It should have representation from the workforce and the management including at least one senior manager. There are two pieces of legislation that cover health and safety consultation with employees and both are summarized in Chapter 17.

3.12.1

The Safety Representatives and Safety Committees Regulations 1977

These regulations only apply to those organizations that have recognized trade unions for collective bargaining purposes. The recognized trade union may appoint safety representatives from among the employees and notify the employer in writing. The safety representative has several functions (not duties) including: ➤ representing employees in consultation with the employer ➤ investigating potential hazards and dangerous occurrences ➤ investigating the causes of accidents ➤ investigating employee complaints relating to health, safety and welfare ➤ making representations to the employer on health, safety and welfare matters ➤ carrying out inspections ➤ representing employees at the workplace in consultation with enforcing inspectors ➤ receiving information ➤ attending safety committee meetings.

Organizing for health and safety ➤ any information resulting from risk assessments or their resultant control measures which could affect the health, safety and welfare of employees ➤ the planning and organization of any health and safety training required by legislation ➤ the health and safety consequences to employees of the introduction of new technologies into the work-place. However, the employer is not expected to disclose information if:

Figure 3.7

Working together.

Representatives must be allowed time off with pay to fulﬁl these functions and to undergo health and safety training. They must also be allowed to inspect the workplace at least once a quarter or sooner if there has been a substantial change in the conditions of work. Finally, if at least two representatives have requested in writing that a safety committee be set up, the employer has three months to comply.

➤ it violates a legal prohibition ➤ it could endanger national security ➤ it relates speciﬁcally to an individual without their consent ➤ it could harm substantially the business of the employer or infringe commercial security ➤ it was obtained in connection with legal proceedings. Finally, an employer should ensure that the representative receives reasonable training in health and safety at the employer’s expense, is allowed time during working hours to perform his duties and provide other facilities and assistance that the representative should reasonably require.

3.12.2 The Health and Safety (Consultation with Employees) Regulations 1996 These regulations were introduced so that employees working in organizations without recognized trade unions would still need to be consulted on health and safety matters. All employees must now be consulted either on an individual basis (e.g. very small companies) or through safety representatives elected by the workforce, known as ROES (Representative(s) of Employee Safety). The guidance to these regulations emphasizes the difference between informing and consulting. Consultation involves listening to the opinion of employees on a particular issue and taking it into account before a decision is made. Informing employees means providing information on health and safety issues such as risks, control systems and safe systems of work. The functions of these representatives are similar to those under the Safety Representatives and Safety Committees Regulations 1977 as are the rights to health and safety training (i.e. time off and costs covered by the employer). The employer must consult on the following: ➤ the introduction of any measure or change which may substantially affect employees’ health and safety ➤ the arrangements for the appointment of competent persons to assist in following health and safety law

3.13 Practice NEBOSH questions for Chapter 3 1. Outline the factors that will determine the level of supervision that a new employee should receive during their initial period of employment within an organization. 2. (a) Explain the meaning of the term ‘competent person’ (b) Outline the organizational factors that may cause a person to work unsafely even though they are competent. 3. Outline a procedure designed to ensure the health and safety of visitors to work premises. 4. List the factors that should be considered when assessing the health and safety competence of a contractor. 5. Outline the checks that could be made in assessing the health and safety competence of a contractor.

43

Introduction to Health and Safety at Work 6. A contractor has been engaged by a manufacturing company to undertake extensive maintenance work on the interior walls of a factory workshop. (a) State the legal duties that the manufacturing company owes the contractor’s employees under the Health and Safety at Work etc. Act 1974 (b) Outline the information relevant to health and safety that should be provided before work commences by: (i) the manufacturing company to the contractor, AND (ii) the contractor to the manufacturing company. (c) Describe additional procedural measures that the manufacturing company should take to help ensure the health and safety of their own and the contractor’s employees. 7. (a) State the circumstances under which an employer must establish a health and safety committee (b) Give six reasons why a health and safety committee may prove to be ineffective in practice. 8. Outline ways to help ensure the effectiveness of a safety committee. 9. Outline the beneﬁts to an organization of having a health and safety committee. 10. In relation to the Safety Representatives and Safety Committees Regulations 1977, outline: (i) the rights and functions of a trade union appointed safety representative (ii) the facilities that an employer may need to provide to safety representatives.

44

11. With respect to the Safety Representatives and Safety Committees Regulations 1977, state when a safety representative is legally entitled to inspect the workplace. 12. By reference to the Safety Representatives and Safety Committees Regulations 1977: (a) explain the circumstances under which an employer must form a health and safety committee (b) identity TWO reasons why a safety representative may have cause to complain to an Employment Tribunal and state the period of time within which such a complaint must be made. 13. In relation to the Health and Safety (Consultation with Employees) Regulations 1996, identify: (i) the health and safety matters on which employers have a duty to consult their employees (ii) four types of information that an employer is not obliged to disclose to an employee representative. 14. With reference to the Health and Safety (Consultation with Employees) Regulations 1996: (i) explain the difference between consulting and informing (ii) outline the health and safety matters on which employers must consult their employees (iii) outline the entitlements of representatives of employee safety who have been elected under the Regulations. 15. In relation to the Health and Safety (Consultation with Employees) Regulations 1996, outline the types of facility that an employer may need to provide to representatives of employee safety.

Organizing for health and safety Appendix 3.1

Typical organizational responsibilities

Senior managers ➤ Are responsible and held accountable for the relevant organization’s health and safety performance. ➤ Develop strong, positive health and safety attitudes among those employees reporting directly to them. ➤ Provide guidance to their management team. ➤ Establish minimum acceptable health and safety standards within the organization. ➤ Provide necessary stafﬁng and funding for the health and safety effort within the organization. ➤ Authorize necessary major expenditures. ➤ Evaluate, approve, and authorize health and safety-related projects developed by members of the organization’s health and safety advisers. ➤ Review and approve policies, procedures, and programmes developed by group staff. ➤ Maintain a working knowledge of areas of health and safety that are regulated by governmental agencies. ➤ Keep health and safety in the forefront by including it as a topic in business discussions. ➤ Review health and safety performance statistics and provide feedback to the management team. ➤ Review and act upon major recommendations submitted by outside loss-prevention consultants. ➤ Make health and safety a part of site tours by making speciﬁc remarks about observations of acts or conditions that fall short of or exceed health and safety standards. ➤ Personally investigate fatalities and major property losses. ➤ Personally chair the organization’s main health and safety committee (if applicable).

Site managers ➤ Are responsible and held accountable for their site’s health and safety performance. ➤ Establish, implement, and maintain a formal, written site health and safety programme, encompassing applicable areas of loss prevention, that is consistent with the organization’s health and safety policy. ➤ Establish controls to ensure uniform adherence to health and safety programme elements. These controls should include corrective action and follow-up. ➤ Develop, by action and example, a positive health and safety attitude and a clear understanding of speciﬁc responsibilities in each member of management.

➤ Approve and adopt local health and safety policies, rules, and procedures. ➤ Chair the site health and safety committee. ➤ Personally investigate fatalities, serious lost workday case injuries, and major property losses. ➤ Review monthly health and safety activity reports and performance statistics. ➤ Review lost workday cases injury/illness investigation reports. ➤ Review health and safety reports submitted by outside agencies. ➤ Attend site health and safety audits regularly to appraise the programme’s effectiveness. ➤ Review annually the health and safety programme’s effectiveness and make adjustments where necessary. ➤ Evaluate the functional performance of the health and safety staff and provide guidance or training where necessary. ➤ Personally review, sign and approve corrective action planned for lost-time accidents. ➤ Monitor staff’s progress toward achieving their health and safety goals and objectives.

Department managers ➤ Are responsible and held accountable for their department’s or area’s health and safety performance. ➤ Contact each supervisor frequently (daily) about health and safety. ➤ Hold departmental health and safety meetings for staff at least once a month. ➤ Make daily observations of supervisors’ health and safety activities. ➤ Review and approve all job procedures developed as a result of job safety analyses; install approved procedures; require each supervisor to check use of the procedures. ➤ Approve and annually review all departmental health and safety risk assessments, rules and regulations; maintain strict enforcement; and develop plans to ensure employee instruction and re-instruction. ➤ Establish acceptable housekeeping standards, deﬁning speciﬁc areas of responsibility, assign areas to supervisors; make a daily spot check of some area; hold formal inspection with supervisors at least monthly, submit written reports with assignments and deadlines for corrections. ➤ Authorize purchases of tools and equipment necessary to attain compliance with site speciﬁcations and statutory regulations.

Introduction to Health and Safety at Work

➤ Develop a training plan that includes speciﬁc job instructions for new or transferred employees; follow up on training by supervisors. ➤ Review the health and safety performance of their area of responsibility. ➤ Personally investigate all lost workday cases and signiﬁcant losses and report to the site manager; follow up on corrective action. ➤ Adopt standards for assigning personal protective equipment to employees; insist on strict enforcement; and make spot ﬁeld checks to determine compliance. ➤ Evaluate supervisors’ health and safety performances. ➤ Develop in each member of management strong health and safety attitudes and clear-cut understanding of speciﬁc duties and responsibilities. ➤ Instil, by action, example, and training, a sincere health and safety attitude. ➤ Instruct supervisors in site procedures for the care and treatment of sick or injured employees.

Supervisors ➤ Are responsible and held accountable for their group’s health and safety performance. ➤ Conduct health and safety meetings for employees at least monthly. ➤ Enforce safe job procedures, such as those developed by job safety analyses. ➤ Report to manager and act upon any weaknesses in safe job procedures, as revealed by health and safety risk assessments and observations. ➤ Report jobs not covered by safe job procedures. ➤ Review unsafe acts and conditions and direct daily health and safety activities to correct the causes. ➤ Instruct employees in health and safety rules and regulations; make records of instruction; and enforce all health and safety rules and regulations. ➤ Make daily inspections of assigned work areas and take immediate steps to correct unsafe or unsatisfactory conditions; report to the manager those conditions that cannot be immediately corrected; instruct employees on housekeeping standards. ➤ Instruct employees that tools/equipment are to be inspected before each use; make spot checks of tools’/equipment’s condition. ➤ Instruct each new employee personally on job health and safety requirements in assigned work areas. ➤ Enforce the organization’s/site’s medical recommendations with respect to an employee’s physical limitations. Report on employee’s apparent physical limitations to their manager; and request physical examination of the employee. ➤ Enforce personal protective equipment requirements; make spot checks to determine that protective apparel is being used; and periodically appraise condition of equipment.

➤ See that, in a case of serious injury, the injured employee receives prompt medical attention; isolate the area or shut down equipment, as necessary; and immediately report to the manager the facts regarding the employee’s accident or illness and any action taken. In serious incident cases, the supervisor determines the cause, takes immediate steps to correct an unsafe condition, and isolates area and/or shuts down the equipment, as necessary. They immediately report facts and action taken to the manager. ➤ Make thorough investigation of all accidents, serious incidents, and cases of ill-health involving employees in assigned work areas; immediately after the accident, prepare a complete accident investigation report and include recommendations for preventing recurrence. ➤ Check changes in operating practices, procedures, and conditions at the start of each shift/day and before relieving the ‘on-duty’ supervisor (if applicable), noting health and safety-related incidents that have occurred since their last working period. ➤ Make, at the start of each shift/day, an immediate check to determine absentees. If site injury is claimed, an immediate investigation is instituted and the department manager is notiﬁed. ➤ Make daily spot checks and take necessary corrective action regarding housekeeping, unsafe acts or practices, unsafe conditions, job procedures and adherence to health and safety rules. ➤ Attend all scheduled and assigned health and safety training meetings. ➤ Instruct personally or provide on-the-job instruction on safe and efﬁcient performance of assigned jobs. ➤ Act on all employee health and safety complaints and suggestions. ➤ Maintain, in their assigned area, health and safety signs and notice boards in a clean and legible condition.

Employees ➤ Are responsible for their own safety and health. ➤ Ensure that their actions will not jeopardize the safety or health of other employees. ➤ Are alert to observe and correct, or report, unsafe practices and conditions. ➤ Maintain a healthy and safe place to work and cooperate with managers in the implementation of health and safety matters. ➤ Make suggestions to improve any aspect of health and safety. ➤ Maintain an active interest in health and safety. ➤ Learn and follow the operating procedures and health and safety rules and procedures for safe performance of the job. ➤ Follow the established procedures if accidents occur.

Organizing for health and safety Appendix 3.2

Checklist for supply chain health and safety management

This checklist is taken from the HSE leaﬂet INDG268 Working Together: Guidance on Health and Safety for Contractors and Suppliers 2002. It is a reminder of the topics that might need to be discussed with people who individual contractors may be working with. It is not intended to be exhaustive and not all questions will apply at any one time, but it should help people to get started.

1

Responsibilities

➤ ➤ ➤ ➤

What are the hazards of the job? Who is to assess particular risks? Who will co-ordinate action? Who will monitor progress?

2

The job

➤ ➤ ➤ ➤ ➤

Where is it to be done? Who with? Who is in charge? How is the job to be done? What other work will be going on at the same time? ➤ How long will it take? ➤ What time of day or night? ➤ Do you need any permit to do the work?

3

Is any monitoring required? Is health surveillance necessary, e.g. for work with sensitizers? (refer to health and safety data sheet).

Plant and equipment ➤ What are the supplier/hirer/manufacturer’s instructions? ➤ Are any certiﬁcates of examination and test needed? ➤ What arrangements have been made for inspection and maintenance? ➤ What arrangements are there for shared use? ➤ Are the electrics safe to use? Check the condition of power sockets, plugs, leads and equipment. (Don’t use damaged items until they have been repaired.) ➤ What assessments have been made of noise levels?

4

People

➤ Is information, instruction and training given, as appropriate? ➤ What are the supervision arrangements? ➤ Are members of the public/inexperienced people involved? ➤ Have any disabilities/medical conditions been considered?

The hazards and risk assessments

Site and location

5

Consider the means of getting into and out of the site and the particular place of work – are they safe; and

➤ What arrangements are there for warning systems in case of ﬁre and other emergencies? ➤ What arrangements have been made for ﬁre/ emergency drills? ➤ What provision has been made for ﬁrst aid and ﬁre-ﬁghting equipment? ➤ Do you know where your nearest ﬁre exits are? ➤ What are the accident reporting arrangements? ➤ Are the necessary arrangements made for availability of rescue equipment and rescuers?

➤ ➤ ➤ ➤

Will any risks arise from environmental conditions? Will you be remote from facilities and assistance? What about physical/structural conditions? What arrangements are there for security?

Substances ➤ ➤ ➤ ➤

What supplier’s information is available? Is there likely to be any microbiological risk? What are the storage arrangements? What are the physical conditions at the point of use? Check ventilation, temperature, electrical installations etc. ➤ Will you encounter substances that are not supplied, but produced in the work, e.g. fumes from hot work during dismantling plant? Check how much, how often, for how long, method of work, etc. ➤ What are the control measures? For example, consider preventing exposure, providing engineering controls, using personal protection (in that order of choice);

6

Emergencies

Welfare

Who will provide: ➤ ➤ ➤ ➤ ➤

shelter food and drinks washing facilities toilets (male and female) and clothes changing/drying facilities?

There may be other pressing requirements which make it essential to re-think health and safety as the work progresses.

This page intentionally left blank

Promoting a positive health and safety culture

4.1 Introduction In 1972, the Robens report recognized that the introduction of health and safety management systems was essential if the ideal of self-regulation of health and safety by industry was to be realized. It further recognized that a more active involvement of the workforce in such systems was essential if self-regulation was to work. Selfregulation and the implicit need for health and safety management systems and employee involvement was incorporated into the Health and Safety at Work Act 1974. Since the introduction of the HSW Act, health and safety standards have improved considerably but there have been some catastrophic failures. One of the worst was the ﬁre on the off-shore oil platform, Piper Alpha, in 1988 when 167 people died. At the subsequent inquiry, the concept of a safety culture was deﬁned by the Director General of the HSE at the time, J R Rimington.

Figure 4.1

Safety investment.

4

This deﬁnition has remained as one of the main checklists for a successful health and safety management system.

4.2 Definition of a health and safety culture The health and safety culture of an organization may be described as the development stage of the organization in health and safety management at a particular time. HSG 65 gives the following deﬁnition of a health and safety culture: The safety culture of an organization is the product of individual and group values, attitudes, perceptions, competencies and patterns of behaviour that determine the commitment to, and the style and proficiency of, an organization’s health and safety management. Organizations with a positive safety culture are characterized by communications founded on mutual trust, by shared perceptions of the importance of safety and by confidence in the efficacy of preventive measures. There is concern among some health and safety professionals that many health and safety cultures are developed and driven by senior managers with very little input from the workforce. Others argue that this arrangement is sensible because the legal duties are placed on the employer. A positive health and safety culture needs the involvement of the whole workforce just as a successful quality system does. There must be a joint commitment in terms of attitudes and values. The workforce must believe that the safety measures put in place will

49

Introduction to Health and Safety at Work be effective and followed even when ﬁnancial and performance targets may be affected.

4.3 Safety culture and safety performance 4.3.1

The relationship between health and safety culture and health and safety performance

The following elements are the important components of a positive health and safety culture: ➤ leadership and commitment to health and safety throughout and at all levels of the organization ➤ acceptance that high standards of health and safety are achievable as part of a long-term strategy formulated by the organization ➤ a detailed assessment of health and safety risks in the organization and the development of appropriate control and monitoring systems ➤ a health and safety policy statement outlining shortand long-term health and safety objectives. Such a policy should also include codes of practice and required health and safety standards ➤ relevant employee training programmes and communication and consultation procedures ➤ systems for monitoring equipment, processes and procedures and the prompt rectiﬁcation of any defects ➤ the prompt investigation of all incidents and accidents and reports made detailing any necessary remedial actions. If the organization adheres to these elements, then a basis for a good performance in health and safety will have been established. However, to achieve this level of performance, sufﬁcient ﬁnancial and human resources must be made available for the health and safety function at all levels of the organization. All managers, supervisors and members of the governing body (e.g. directors) should receive training in health and safety and be made familiar during training sessions with the health and safety targets of the organization. The depth of training undertaken will depend on the level of competence required of the particular manager. Managers should be accountable for health and safety within their departments and be rewarded for signiﬁcant improvements in health and safety performance. They should also be expected to discipline employees within their departments who infringe health and safety policies or procedures.

50

4.3.2

Important indicators of a health and safety culture

There are several outputs or indicators of the state of the health and safety culture of an organization. The most important are the numbers of accidents, near misses and occupational ill-health cases occurring within the organization. While the number of accidents may give a general indication of the health and safety culture, a more detailed examination of accidents and accident statistics is normally required. A calculation of the rate of accidents enables health and safety performance to be compared between years and organizations. The simplest measure of accident rate is called the incident rate and is deﬁned as: Total number of accidents 1000 Number of persons employed or the total number of accidents per 1000 employees. A similar measure (per 100 000) is used by the HSC in its annual report on national accident statistics and enables comparisons to be made within an organization between time periods when employee numbers may change. It also allows comparisons to be made with the national occupational or industrial group relevant to the organization. There are four main problems with this measure which must be borne in mind when it is used. These are: ➤ there may be a considerable variation over a time period in the ratio of part-time to full-time employees ➤ the measure does not differentiate between major and minor accidents and takes no account of other incidents, such as those involving damage but no injury (although it is possible to calculate an incidence rate for a particular type or cause of accident) ➤ there may be signiﬁcant variations in work activity during the periods being compared ➤ under-reporting of accidents will affect the accuracy of the data. Subject to the above limitations, an organization with a high accident incidence rate is likely to have a negative or poor health and safety culture. There are other indications of a poor health and safety culture or climate. These include: ➤ a high sickness, ill-health and absentee rate amongst the workforce ➤ the perception of a blame culture ➤ high staff turnover leading to a loss of momentum in making health and safety improvements ➤ no resources (in terms of budget, people or facilities) made available for the effective management of health and safety

Promoting a positive health and safety culture ➤ a lack of compliance with relevant health and safety law and the safety rules and procedures of the organization ➤ poor selection procedures and management of contractors ➤ poor levels of communication, cooperation and control ➤ a weak health and safety management structure ➤ either a lack or poor levels of health and safety competence ➤ high insurance premiums.

Major accident 1

Minor accident 30

Near miss (no injury) 300

In summary, a poor health and safety performance within an organization is an indication of a negative health and safety culture.

4.3.3

Factors affecting a health and safety culture

The most important factor affecting the culture is the commitment to health and safety from the top of an organization. This commitment may be shown in many different ways. It needs to have a formal aspect in terms of an organizational structure, job descriptions and a health and safety policy, but it also needs to be apparent during crises or other stressful times. The health and safety procedures may be circumvented or simply forgotten when production or other performance targets are threatened. Structural reorganization or changes in market conditions will produce feelings of uncertainty among the workforce which, in turn, will affect the health and safety culture. Poor levels of supervision, health and safety information and training are very signiﬁcant factors in reducing health and safety awareness and, therefore, the culture. Finally, the degree of consultation and involvement with the workforce in health and safety matters is crucial for a positive health and safety culture. Most of these factors may be summed up as human factors.

4.4 Human factors and their influence on safety performance

Figure 4.2

This study indicated that for every 10 near misses, there will be an accident. While the accuracy of this study may be debated and other studies have produced different ratios, it is clear that if near misses are continually ignored, an accident will result. Further, the HSE Accident Prevention Unit has suggested that 90% of all accidents are due to human error and 70% of all accidents could have been avoided by earlier (proactive) action by management. It is clear from many research projects that the major factors in most accidents are human factors. The HSE has deﬁned human factors as, ‘environmental, organizational and job factors, and human and individual characteristics which inﬂuence behaviour at work in a way which can affect health and safety’. In simple terms, the health and safety of people at work are inﬂuenced by: ➤ the organization ➤ the job ➤ personal factors. These are known as human factors since they each have a human involvement. The personal factors which differentiate one person from another are only one part of those factors – and not always the most important. Each of these elements will be considered in turn.

4.4.2 4.4.1

Heinrich’s accidents/incidents ratios.

The organization

Human factors

Over the years, there have been several studies undertaken to examine the link between various accident types, graded in terms of their severity, and near misses. One of the most interesting was conducted in the USA by H W Heinrich in 1950. He looked at over 300 accidents/ incidents and produced the ratios illustrated in Figure 4.2.

The organization is the company or corporate body and has the major inﬂuence on health and safety. It must have its own positive health and safety culture and produce an environment in which it: ➤ manages health and safety throughout the organization, including the setting and publication of a health

51

Introduction to Health and Safety at Work and safety policy and the establishment of a health and safety organizational structure ➤ measures the health and safety performance of the organization at all levels and in all departments. The performance of individuals should also be measured. There should be clear health and safety targets and standards and an effective reporting procedure for accidents and other incidents so that remedial actions may be taken ➤ motivates managers within the organization to improve health and safety performance in the workplace in a proactive rather than reactive manner. The HSE has recommended that an organization needs to provide the following elements within its management system: ➤ a clear and evident commitment from the most senior manager downwards, which provides a climate for safety in which management’s objectives and the need for appropriate standards are communicated and in which constructive exchange of information at all levels is positively encouraged ➤ an analytical and imaginative approach identifying possible routes to human factor failure. This may well require access to specialist advice ➤ procedures and standards for all aspects of critical work and mechanisms for reviewing them ➤ effective monitoring systems to check the implementation of the procedures and standards ➤ incident investigation and the effective use of information drawn from such investigations ➤ adequate and effective supervision with the power to remedy deﬁciencies when found. It is important to recognize that there are often reasons for these elements not being present resulting in weak management of health and safety. The most common reason is that individuals within the management organization do not understand their roles – or their roles have never been properly explained to them. The higher a person is within the structure the less likely it is that he has received any health and safety training. Such training at board level is rare. Objectives and priorities may vary across and between different levels in the structure leading to disputes which affect attitudes to health and safety. For example, a warehouse manager may be pressured to block walkways so that a large order can be stored prior to dispatch. Motivations can also vary across the organization which may cause health and safety to be compromised. The production controller will require that components of a product are produced as near simultaneously as possible so that their ﬁnal assembly is performed as quickly as

52

possible. However, the health and safety adviser will not want to see safe systems of work compromised. In an attempt to address some of these problems, the HSC produced guidance in 2001 on the safety duties of company directors. Each director and the Board, acting collectively, will be expected to provide health and safety leadership in the organization. The Board will need to ensure that all its decisions reﬂect its health and safety intentions and that it engages the workforce actively in the improvement of health and safety. The Board will also be expected to keep itself informed of changes in health and safety risks. (See Chapter 3 for more details on directors’ responsibilities.) The following simple checklist may be used to check any organizational health and safety management structure. Does the structure have: ➤ an effective health and safety management system? ➤ a positive health and safety culture? ➤ arrangements for the setting and monitoring of standards? ➤ adequate supervision? ➤ effective incident reporting and analysis? ➤ learning from experience? ➤ clearly visible health and safety leadership? ➤ suitable team structures? ➤ efﬁcient communication systems and practices? ➤ adequate stafﬁng levels? ➤ suitable work patterns? HSG48 gives the following causes for failures in organizational and management structures: ➤ ➤ ➤ ➤ ➤ ➤ ➤

poor work planning, leading to high work pressure lack of safety systems and barriers inadequate responses to previous incidents management based on one-way communications deﬁcient coordination and responsibilities poor management of health and safety poor health and safety culture.

Organizational factors play a signiﬁcant role in the health and safety of the workplace. However, this role is often forgotten when health and safety is being reviewed after an accident or when a new process or piece of equipment is introduced.

4.4.3

The job

Jobs may be highly dangerous or present only negligible risk of injury. Health and safety is an important element during the design stage of the job and any

Promoting a positive health and safety culture equipment, machinery or procedures associated with the job. Method study helps to design the job in the most cost effective way and ergonomics helps to design the job with health and safety in mind. Ergonomics is the science of matching equipment and machines to man rather than the other way round. An ergonomically designed machine will ensure that control levers, dials, meters and switches are sited in a convenient and comfortable position for the machine operator. Similarly, an ergonomically designed workstation will be designed for the comfort and health of the operator. Chairs, for example, will be designed to support the back properly throughout the working day. Physically matching the job and any associated equipment to the person will ensure that the possibility of human error is minimized. It is also important to ensure that there is mental matching of the person’s information and decision-making requirements. A person must be capable, either through past experience or through speciﬁc training, to perform the job with the minimum potential for human error. The major considerations in the design of the job, which would be undertaken by a specialist, have been listed by the HSE as follows: ➤ the identiﬁcation and detailed analysis of the critical tasks expected of individuals and the appraisal of any likely errors associated with those tasks ➤ evaluation of the required operator decision making and the optimum (best) balance between the human and automatic contributions to safety actions (with the emphasis on automatic whenever possible) ➤ application of ergonomic principles to the design of man–machine interfaces, including displays of plant and process information, control devices and panel layout ➤ design and presentation of procedures and operating instructions in the simplest terms possible ➤ organization and control of the working environment, including the workspace, access for maintenance, lighting, noise and heating conditions ➤ provision of the correct tools and equipment ➤ scheduling of work patterns, including shift organization, control of fatigue and stress and arrangements for emergency operations ➤ efﬁcient communications, both immediate and over a period of time. For some jobs, particularly those with a high risk of injury, a job safety analysis should be undertaken to check that all necessary safeguards are in place. All jobs should carry a job description and a safe system of work for the particular job. The operator should have sight of the job description and be trained in the safe system of work

Figure 4.3 standing.

Well-designed workstation for sitting or

before commencing the job. More information on both these latter items is given in Chapter 6. The following simple checklist may be used to check that the principal health and safety considerations of the job have been taken into account: ➤ have the critical parts of the job been identiﬁed and analysed? ➤ have the employee’s decision-making needs been evaluated? ➤ has the best balance between human and automatic systems been evaluated? ➤ have ergonomic principles been applied to the design of equipment displays, including displays of plant and process information, control information and panel layouts? ➤ has the design and presentation of procedures and instructions been considered? ➤ has the guidance available for the design and control of the working environment, including the workspace, access for maintenance, lighting, noise and heating conditions, been considered? ➤ have the correct tools and equipment been provided? ➤ have the work patterns and shift organization been scheduled to minimize their impact on health and safety? ➤ has consideration been given to the achievement of efﬁcient communications and shift handover?

53

Introduction to Health and Safety at Work

Figure 4.4

Poor working conditions.

HSG48 gives following causes for failures in job health and safety: ➤ ➤ ➤ ➤ ➤ ➤

illogical design of equipment and instruments constant disturbances and interruptions missing or unclear instructions poorly maintained equipment high workload noisy and unpleasant working conditions.

It is important that health and safety monitoring of the job is a continuous process. Some problems do not become apparent until the job is started. Other problems do not surface until there is a change of operator or a change in some aspect of the job. It is very important to gain feedback from the operator on any difﬁculties experienced because there could be a health and safety issue requiring further investigation.

4.4.4

Personal factors

Personal factors, which affect health and safety, may be deﬁned as any condition or characteristic of an individual which could cause or inﬂuence him to act in an unsafe manner. They may be physical, mental or psychological in nature. Personal factors, therefore, include issues such as attitude, motivation, training and human error and their interaction with the physical, mental and perceptual capability of the individual. These factors have a signiﬁcant effect on health and safety. Some of them, normally involving the personality of the individual, are unchangeable but others, involving skills, attitude, perception and motivation can be changed, modiﬁed or improved by suitable training or other measures. In summary, the person needs to be matched to the job. Studies have shown that the most common personal factors which contribute to accidents are low skill and

54

competence levels, tiredness, boredom, low morale and individual medical problems. It is difﬁcult to separate all the physical, mental or psychological factors because they are interlinked. However, the three most common factors are psychological factors – attitude, motivation and perception. Attitude is the tendency to behave in a particular way in a certain situation. Attitudes are inﬂuenced by the prevailing health and safety culture within the organization, the commitment of the management, the experience of the individual and the inﬂuence of the peer group. Peer group pressure is a particularly important factor among young people and health and safety training must be designed with this in mind by using examples or case studies that are relevant to them. Behaviour may be changed by training, the formulation and enforcement of safety rules and meaningful consultation – attitude change often follows. Motivation is the driving force behind the way a person acts or the way in which people are stimulated to act. Involvement in the decision-making process in a meaningful way will improve motivation as will the use of incentive schemes. However, there are other important inﬂuences on motivation such as recognition and promotion opportunities, job security and job satisfaction. Self-interest, in all its forms, is a signiﬁcant motivator and personal factor. Perception is the way in which people interpret the environment or the way in which a person believes or understands a situation. In health and safety, the perception of hazards is an important concern. Many accidents occur because people do not perceive that there is a risk. There are many common examples of this, including the use of personal protective equipment (such as hard hats) and guards on drilling machines and the washing of hands before meals. It is important to understand that when perception leads to an increased health and safety risk, it is not always caused by a conscious decision of the individual concerned. The stroboscopic effect caused by the rotation of a drill at certain speeds under ﬂuorescent lighting will make the drill appear stationary. It is a well-known phenomenon, especially among illusionists, that people will often see what they expect to see rather than reality. Routine or repetitive tasks will reduce attention levels leading to the possibility of accidents. Other personal factors which can affect health and safety include physical stature, age, experience, health, hearing, intelligence, language, skills, level of competence and qualiﬁcations. Finally, memory is an important personal factor since it is inﬂuenced by training and experience. The efﬁciency of memory varies considerably between people and during the lifetime of an individual. The overall health of a person can affect memory as can personal crises. Due to these possible problems with memory, important

Promoting a positive health and safety culture

(a)

(b)

Figure 4.5

(c)

Visual perception (a) Are the lines the same length? (b) Face or vase? (c) Face or saxophone player?

safety instructions should be available in written as well as verbal form. The following checklist given in HSG48 may be used to check that the relevant personal factors have been covered: ➤ has the job speciﬁcation been drawn up and included age, physique, skill, qualiﬁcations, experience, aptitude, knowledge, intelligence and personality? ➤ have the skills and aptitudes been matched to the job requirements? ➤ have the personnel selection policies and procedures been set up to select appropriate individuals? ➤ has an effective training system been implemented? ➤ have the needs of special groups of employees been considered? ➤ have the monitoring procedures been developed for the personal safety performance of safety critical staff? ➤ have ﬁtness for work and health surveillance been provided where it is needed? ➤ has counselling and support for ill-health and stress been provided?

Setting goals leads to vigorous activity if: The goal is realistic. A serious commitment is made, especially if it is made publicly. Feedback is received.

Figure 4.6

Motivation and activity.

Personal factors are the attributes that employees bring to their jobs and may be strengths or weaknesses. Negative personal factors cannot always be neutralized by improved job design. It is, therefore, important

55

Introduction to Health and Safety at Work to ensure that personnel selection procedures should match people to the job. This will reduce the possibility of accidents or other incidents.

4.5 Human errors and violations Human failures in health and safety are either classiﬁed as errors or violations. An error is an unintentional deviation from an accepted standard, while a violation is a deliberate deviation from the standard (see Figure 4.7).

4.5.1

Human errors

Human errors fall into three groups – slips, lapses and mistakes, which can be further sub-divided into rulebased and knowledge-based mistakes.

Slips and lapses These are very similar in that they are caused by a momentary memory loss often due to lack of attention or loss of concentration. They are not related to levels of training, experience or motivation and they can usually be reduced by re-designing the job or equipment or minimizing distractions. Slips are failures to carry out the correct actions of a task. Examples include the use of the incorrect switch, reading the wrong dial or selecting the incorrect component for an assembly. A slip also describes an action taken too early or too late within a given working procedure. Lapses are failures to carry out particular actions which may form part of a working procedure. A fork lift truck driver leaving the keys in the ignition lock of his truck is an example of a lapse as is the failure to replace the petrol cap on a car after ﬁlling it with petrol. Lapses

Slips of action Skill-based errors Lapses of memory Errors Rule-based mistakes Mistakes Knowledgebased mistakes

Human failures

Routine

Violations

Situational

Exceptional

Figure 4.7

56

Types of human failure.

Promoting a positive health and safety culture may be reduced by re-designing equipment so that, for example, an audible horn indicates the omission of a task. They may also be reduced signiﬁcantly by the use of detailed checklists.

Mistakes Mistakes occur when an incorrect action takes place but the person involved believes the action to be correct. A mistake involves an incorrect judgement. There are two types of mistakes – rule-based and knowledge-based. Rule-based mistakes occur when a rule or procedure is remembered or applied incorrectly. These mistakes usually happen when, due to an error, the rule that is normally used no longer applies. For example, a particular job requires the counting of items into groups of ten followed by the adding together of the groups so that the total number of items may be calculated. If one of the groups is miscounted, the ﬁnal total will be incorrect even though the rule has been followed. Knowledge-based mistakes occur when well-tried methods or calculation rules are used inappropriately. For example, the depth of the foundations required for a particular building was calculated using a formula. The formula, which assumed a clay soil, was used to calculate the foundation depth in a sandy soil. The resultant building was unsafe. The HSE has suggested the following points to consider when the potential source of human errors are to be identiﬁed: ➤ What human errors can occur with each task? There are formal methods available to help with this task ➤ What inﬂuences are there on performance? Typical inﬂuences include, time pressure, design of controls, displays and procedures, training and experience, fatigue and levels of supervision ➤ What are the consequences of the identiﬁed errors? What are the signiﬁcant errors? ➤ Are there opportunities for detecting each error and recovering it? ➤ Are there any relationships between the identiﬁed errors? Could the same error be made on more than one item of equipment due, for example, to the incorrect calibration of an instrument? Errors and mistakes can be reduced by the use of instruction, training and relevant information. However, communication can also be a problem, particularly at shift handover times. Environmental and organizational factors, involving workplace stress will also affect error levels. The following steps are suggested to reduce the likelihood of human error: ➤ examine and reduce the workplace stressors (e.g. noise, poor lighting, etc.) which increase the frequency of errors

➤ examine and reduce any social or organizational stressors (e.g. insufﬁcient stafﬁng levels, peer pressure, etc.) ➤ design plant and equipment to reduce error possibilities – poorly designed displays, ambiguous instructions ➤ ensure that there are effective training arrangements ➤ simplify any complicated or complex procedures ➤ ensure that there is adequate supervision, particularly for inexperienced or young trainees ➤ check that job procedures, instructions and manuals are kept up to date and are clear ➤ include the possibility of human error when undertaking the risk assessment ➤ isolate the human error element of any accident or incident and introduce measures to reduce the risk of a repeat ➤ monitor the effectiveness of any measures taken to reduce errors.

4.5.2

Violations

There are three categories of violation – routine, situational and exceptional. Routine violation occurs when the breaking of a safety rule or procedure is the normal way of working. It becomes routine not to use the recommended procedures for tasks. An example of this is the regular speeding of fork lift trucks in a warehouse so that orders can be fulﬁlled on time. There are many reasons given for routine violation – the job would not be completed on time, lack of supervision and enforcement or, simply, the lack of knowledge of the procedures. Routine violations can be reduced by regular monitoring, ensuring that the rules are actually necessary or redesigning the job. The following features are very common in many workplaces and often lead to routine violations: ➤ poor working posture due to poor ergonomic design of the workstation or equipment ➤ equipment difﬁcult to use and/or slow in response ➤ equipment difﬁcult to maintain or pressure on time available for maintenance ➤ procedures unduly complicated and difﬁcult to understand ➤ unreliable instrumentation and/or warning systems ➤ high levels of noise and other poor aspects to the environment (fumes, dusts, humidity) ➤ associated personal protective equipment either inappropriate, difﬁcult and uncomfortable to wear or ineffective due to lack of maintenance. Situational violations occur when particular job pressures at particular times make rule compliance difﬁcult.

57

Introduction to Health and Safety at Work They may happen when the correct equipment is not available or weather conditions are adverse. A common example is the use of a ladder rather than a scaffold for working at height to replace window frames in a building. Situational violations may be reduced by improving job design, the working environment and supervision. Exceptional violations rarely happen and usually occur when a safety rule is broken to perform a new task. A good example are the violations which can occur during the operations of emergency procedures such as ﬁres or explosions. These violations should be addressed in risk assessments and during training sessions for emergencies (e.g. ﬁre training). Everybody is capable of making errors. It is one of the objectives of a positive health and safety culture to reduce them and their consequences as much as possible.

4.6 The development of a positive health and safety culture No single section or department of an organization can develop a positive health and safety culture on its own. There needs to be commitment by the management, the promotion of health and safety standards, effective communication within the organization, cooperation from and with the workforce and an effective and developing training programme. Each of these topics will be examined in turn to show their effect on improving the health and safety culture in the organization.

4.6.1

➤ review the status of the health and safety committees and health and safety practitioners. Ensure that any recommendations are acted upon or implemented ➤ ensure that senior managers receive regular reports on health and safety performance and act on them ➤ ensure that any appropriate health and safety actions are taken quickly and are seen to have been taken ➤ any action plans should be developed in consultation with employees, based on a shared perception of hazards and risks, be workable and continuously reviewed.

Commitment of management

As mentioned earlier, there needs to be a commitment from the very top of the organization and this commitment will, in turn, produce higher levels of motivation and commitment throughout the organization. Probably the best indication of this concern for health and safety is shown by the status given to health and safety and the amount of resources (money, time and people) allocated to health and safety. The management of health and safety should form an essential part of a manager’s responsibility and they should be held to account for their performance on health and safety issues. Specialist expertise should be made available when required (e.g. for noise assessment), either from within the workforce or by the employment of external contractors or consultants. Health and safety should be discussed on a regular basis at management meetings at all levels of the organization. If the organization employs sufﬁcient people to make direct consultation with all employees difﬁcult, there should be a health and safety committee

58

at which there is employee representation. In addition, there should be recognized routes for anybody within the organization to receive health and safety information or have their health and safety concerns addressed. The health and safety culture is enhanced considerably when senior managers appear regularly at all levels of an organization whether it be the shop ﬂoor, the hospital ward or the general ofﬁce and are willing to discuss health and safety issues with staff. A visible management is very important for a positive health and safety culture. Finally, the positive results of a management commitment to health and safety will be the active involvement of all employees in health and safety, the continuing improvement in health and safety standards and the subsequent reduction in accident and occupational illhealth rates. This will lead, ultimately, to a reduction in the number and size of compensation claims. HSG48 makes some interesting suggestions to managers on the improvements that may be made to health and safety which will be seen by the workforce as a clear indication of their commitment. The suggestions are:

4.6.2

The promotion of health and safety standards

For a positive health and safety culture to be developed, everyone within the organization needs to understand the standards of health and safety expected by the organization and the role of the individual in achieving and maintaining those standards. Such standards are required to control and minimize health and safety risks. Standards should clearly identify the actions required of people to promote health and safety. They should also specify the competencies needed by employees and they should form the basis for measuring health and safety performance. Health and safety standards cover all aspects of the organization. Typical examples include: ➤ the design and selection of premises ➤ the design and selection of plant and substances (including those used on site by contractors)

Promoting a positive health and safety culture ➤ the recruitment of employees and contractors ➤ the control of work activities, including issues such as risk assessment ➤ competence, maintenance and supervision ➤ emergency planning and training ➤ the transportation of the product and its subsequent maintenance and servicing. Having established relevant health and safety standards, it is important that they are actively promoted within the organization by all levels of management. The most effective method of promotion is by leadership and example. There are many ways to do this such as: ➤ the involvement of managers in workplace inspections and accident investigations ➤ the use of personal protective equipment (e.g. goggles and hard hats) by all managers and their visitors in designated areas ➤ ensuring that employees attend specialist refresher training courses when required (e.g. ﬁrst aid and fork lift truck driving) ➤ full cooperation with ﬁre drills and other emergency training exercises ➤ comprehensive accident reporting and prompt follow up on recommended remedial actions. The beneﬁts of good standards of health and safety will be shown directly in less lost production, accidents and compensation claims and lower insurance premiums. It may also be shown in higher product quality and better resource allocation. An important and central necessity for the promotion of high health and safety standards is health and safety competence. What is meant by ‘competence’?

4.6.3

Competence

The word ‘competence’ is often used in health and safety literature. One deﬁnition, made during a civil case in 1962, stated that a competent person is: a person with practical and theoretical knowledge as well as sufficient experience of the particular machinery, plant or procedure involved to enable them to identify defects or weaknesses during plant and machinery examinations, and to assess their importance in relation to the strength and function of that plant and machinery. This deﬁnition concentrates on a manufacturing rather than service industry requirement of a competent person. Regulation 6 of the Management of Health and Safety at Work Regulations requires that ‘every employer shall employ one or more competent persons to assist

him in undertaking the measures he needs to take to comply with the requirements and prohibitions imposed upon him by or under the relevant statutory provisions’. In other words, competent persons are required to assist the employer in meeting his obligations under health and safety law. This may mean a health and safety adviser in addition to, say, an electrical engineer, an occupational nurse and a noise assessment specialist. The number and range of competent persons will depend on the nature of the business of the organization. It is recommended that competent employees are used for advice on health and safety matters rather than external specialists (consultants). It is recognized, however, that if employees, competent in health and safety, are not available in the organization, then an external service may be enlisted to help. The key is that management and employees need access to health and safety expertise. The regulations do not deﬁne ‘competence’ but do offer advice to employers when appointing health and safety advisers who should have: ➤ a knowledge and understanding of the work involved, the principles of risk assessment and prevention and current health and safety applications ➤ the capacity to apply this to the task required by the employer in the form of problem and solution identiﬁcation, monitoring and evaluating the effectiveness of solutions and the promotion and communication of health and safety and welfare advances and practices. Such competence does not necessarily depend on the possession of particular skills or qualiﬁcations. It may only be required to understand relevant current best practice, be aware of one’s own limitations in terms of experience and knowledge and be willing to supplement existing experience and knowledge. However, in more complex or technical situations membership of a relevant professional body and/or the possession of an appropriate qualiﬁcation in health and safety may be necessary. It is important that any competent person employed to help with health and safety has evidence of relevant knowledge, skills and experience for the tasks involved. The appointment of a competent person as an adviser to an employer does not absolve the employer from his responsibilities under the Health and Safety at Work Act and other relevant statutory provision. Finally, it is worth noting that the requirement to employ competent workers is not restricted to those having a health and safety function but covers the whole workforce. Competent workers must have sufﬁcient training, experience, knowledge and other qualities to enable them to properly undertake the duties assigned to them.

59

Introduction to Health and Safety at Work 4.7 Effective communication Many problems in health and safety arise due to poor communication. It is not just a problem between management and workforce – it is often a problem the other way or indeed at the same level within an organization. It arises from ambiguities or, even, accidental distortion of a message. The Health and Safety (Information for Employees) Regulations require that the latest version of the approved health and safety poster be displayed prominently in the workplace. Additional information on these regulations is given in Chapter 1. There are three basic methods of communication in health and safety – verbal, written and graphic. Verbal communication is the most common. It is communication by speech or word of mouth. Verbal communication should only be used for relatively simple pieces of information or instruction. It is most commonly used in the workplace, during training sessions or at meetings. There are several potential problems associated with verbal communication. The speaker needs to prepare the communication carefully so that there is no confusion about the message. It is very important that the recipient is encouraged to indicate their understanding of the communication. There have been many cases of accidents occurring because a verbal instruction has not been understood. There are several barriers to this understanding from the point of view of the recipient, including language and dialect, the use of technical language and abbreviations, background noise and distractions, hearing problems, ambiguities in the message, mental weaknesses and learning disabilities, lack of interest and attention. Having described some of the limitations of verbal communication, it does have some merits. It is less formal, enables an exchange of information to take place quickly and the message to be conveyed as near to the workplace as possible. Training or instructions that are delivered in this way are called toolbox talks and can be very effective. Written communication takes many forms from the simple memo to the detailed report. A memo should contain one simple message and be written in straightforward and clear language. The title should accurately describe the contents of the memo. In recent years, e-mails have largely replaced memos since it has become a much quicker method to ensure that the message gets to all concerned (although a recent report has suggested that many people are becoming overwhelmed by the number of e-mails which they receive!). The advantage of memos and e-mails is that there is a record of the message after it has been

60

delivered. The disadvantage is that they can be ambiguous or difﬁcult to understand or, indeed, lost within the system. Reports are more substantial documents and cover a topic in greater detail. The report should contain a detailed account of the topic and any conclusions or recommendations. The main problem with reports is that they are often not read properly due to the time constraints on managers. It is important that all reports have a summary attached so that the reader can decide whether it needs to be read in detail (see Section 7.9). The most common way in which written communication is used in the workplace is the notice board. For a notice board to be effective, it needs to be well positioned within the workplace and there needs to be a regular review of the notices to ensure that they are up to date and relevant. There are many other examples of written communications in health and safety, such as employee handbooks, company codes of practice, minutes of safety committee meetings and health and safety procedures. Graphic communication is communication by the use of drawings, photographs or videos. It is used either to impart health and safety information (e.g. ﬁre exits) or health and safety propaganda. The most common forms of health and safety propaganda are the poster and the video. Both can be used very effectively as training aids since they can retain interest and impart a simple message. Their main limitation is that they can become out of date fairly quickly or, in the case of posters, become largely ignored. There are many sources of health and safety information which may need to be consulted before an accurate communication can be made. These include regulations, judgments, approved codes of practice, guidance, British and European standards, periodicals, case studies and HSE publications.

4.8 Health and safety training Health and safety training is a very important part of the health and safety culture and it is also a legal requirement, under the Management of Health and Safety at Work Regulations and other regulations, for an employer to provide such training. Training is required on recruitment, at induction or on being exposed to new or increased risks due to: ➤ being transferred to another job or given a change in responsibilities ➤ the introduction of new work equipment or a change of use in existing work equipment ➤ the introduction of new technology

Promoting a positive health and safety culture ➤ the introduction of a new system of work or the revision of an existing system of work ➤ an increase in the employment of more vulnerable employees (young or disabled persons) ➤ particular training required by the organization’s insurance company (e.g. speciﬁc ﬁre and emergency training). Additional training may well be needed following a single or series of accidents or near misses, the introduction of new legislation, the issuing of an enforcement notice or as a result of a risk assessment or safety audit. It is important during the development of a training course that the target audience is taken into account. If the audience are young persons, the chosen approach must be capable of retaining their interest and any illustrative examples used must be within their experience. The trainer must also be aware of external inﬂuences, such as peer pressures, and use them to advantage. For example, if everybody wears personal protective equipment then it will be seen as the thing to do. Levels of literacy and numeracy are other important factors. The way in which the training session is presented by the use of videos, power point slides, case studies, lectures or small discussion groups needs to be related to the material to be covered and the backgrounds of the trainees. Supplementary information in the form of copies of slides and additional background reading is often useful. The environment used for the training sessions is also important in terms of room layout and size, lighting and heating. Attempts should be made to measure the effectiveness of the training by course evaluation forms issued at the time of the session, by a subsequent refresher session and by checking for improvements in health and safety performance (such as a reduction in speciﬁc accidents). There are several different types of training, these include induction, job speciﬁc, supervisory and management, and specialist. Informal sessions held at the place of work are known as ‘toolbox talks’. Such sessions should only be used to cover a limited number of issues. They can become a useful route for employee consultation.

4.8.1

Most induction training programmes would include the following topics: ➤ the health and safety policy of the organization including a summary of the organization and arrangements including employee consultation ➤ a brief summary of the health and safety management system including the name of the employee’s direct supervisor, safety representative and source of health and safety information ➤ the employee responsibility for health and safety including any general health and safety rules (e.g. smoking prohibitions) ➤ the accident reporting procedure of the organization, the location of the accident book and the location of the nearest ﬁrst aider ➤ the ﬁre and other emergency procedures including the location of the assembly point ➤ a summary of any relevant risk assessments and safe systems of work ➤ the location of welfare, canteen facilities and rest rooms. Additional items, which are speciﬁc to the organization, may need to be included such as: ➤ internal transport routes and pedestrian walkways (e.g. fork lift truck operations) ➤ the correct use of personal protective equipment and maintenance procedures ➤ manual handling techniques and procedures ➤ details of any hazardous substances in use and any procedures relating to them (e.g. health surveillance). There should be some form of follow-up with each new employee after 3 months to check that the important messages have been retained. This is sometimes called a refresher course, although it is often better done on a one-to-one basis. It is very important to stress that the content of the induction course should be subject to constant review and updated following an accident investigation, new legislation, changes in the ﬁndings of a risk assessment or the introduction of new plant or processes.

Induction training 4.8.2

Induction training should always be provided to new employees, trainees and possibly contractors. While such training covers items such as pay, conditions and quality, it must also include health and safety. It is useful if the employee signs a record to the effect that training has been received. This record may be required as evidence should there be a subsequent legal claim against the organization.

Job-specific training

Job-speciﬁc training ensures that employees undertake their job in a safe manner. Such training, therefore, is a form of skill training and is often best done ‘on the job’ – sometimes known as ‘toolbox training’. Details of the safe system of work or, in more hazardous jobs, a permit to work system should be covered. In addition to normal safety procedures, emergency procedures and

61

Introduction to Health and Safety at Work the correct use of personal protective equipment also needs to be included. The results of risk assessments are very useful in the development of this type of training. It is important that any common causes of human errors (e.g. discovered as a result of an accident investigation), any standard safety checks or maintenance requirements are addressed. It is common for this type of training to follow an operational procedure in the form of a checklist which the employee can sign on completion of the training. The new employee will still need close supervision for some time after the training has been completed.

4.8.3

Supervisory and management training

Supervisory and management health and safety training follows similar topics to those contained in an induction training course but will be covered in more depth. There will also be a more detailed treatment of health and safety law. There has been considerable research over the years into the failures of managers that have resulted in accidents and other dangerous incidents. These failures have included: ➤ lack of health and safety awareness, enforcement and promotion (in some cases there has been an encouragement to circumvent health and safety rules) ➤ lack of consistent supervision of and communication with employees ➤ lack of understanding of the extent of the responsibility of the supervisor. It is important that all levels of management, including the board, receive health and safety training. This will not only keep everybody informed of health and safety legal requirements, accident prevention techniques and changes in the law, but also encourage everybody to monitor health and safety standards during visits or tours of the organization.

4.8.4

Specialist training

Specialist health and safety training is normally needed for activities that are not related to a speciﬁc job but more to an activity. Examples include ﬁrst aid, ﬁre prevention, fork lift truck driving, overhead crane operation, scaffold inspection and statutory health and safety inspections. These training courses are often provided by specialist organizations and successful participants are awarded certiﬁcates. Details of two of these courses will be given here by way of illustration. Fire prevention training courses include the causes of ﬁre and ﬁre spread, ﬁre and smoke alarm

62

systems, emergency lighting, the selection and use of ﬁre extinguishers and sprinkler systems, evacuation procedures, high risk operations and good housekeeping principles. A fork lift truck drivers’ course would include the general use of the controls, loading and unloading procedures, driving up or down an incline, speed limits, pedestrian awareness (particularly in areas where pedestrians and vehicles are not segregated), security of the vehicle when not in use, daily safety checks and defect reporting, refuelling and/or battery charging and emergency procedures. Details of other types of specialist training appear elsewhere in the text. Training is a vital part of any health and safety programme and needs to be constantly reviewed and updated. Many health and safety regulations require speciﬁc training (e.g. manual handling, personal protective equipment and display screens). Additional training courses may be needed when there is a major reorganization, a series of similar accidents or incidents or a change in equipment or a process. Finally, the methods used to deliver training must be continually monitored to ensure that they are effective.

4.9 Internal influences There are many inﬂuences on health and safety standards, some are positive and others negative. No business, particularly small businesses, is totally divorced from their suppliers, customers and neighbours. This section considers the internal inﬂuences on a business, including management commitment, production demands, communication, competence and employee relations.

4.9.1

Management commitment

Managers, particularly senior managers, can give powerful messages to the workforce by what they do for health and safety. Managers can achieve the level of health and safety performance that they demonstrate they want to achieve. Employees soon get the negative message if directors disregard safety rules and ignore written policies to get urgent production to the customer or to avoid personal inconvenience. It is what they do that counts not what they say. In Chapter 3 managers’ organizational roles were listed showing the ideal level of involvement for senior managers. Depending on the size and geography of the organization, senior managers should be personally involved in: ➤ health and safety inspections or audits ➤ meetings of the central health and safety or joint consultation committees

Promoting a positive health and safety culture ➤ involvement in the investigation of accidents, illhealth and incidents. The more serious the incident the more senior the manager who takes an active part in the investigation.

4.9.2

Production/service demands

Managers need to balance the demands placed by customers and action required to protect the health and safety of their employees. How this is achieved has a strong inﬂuence on the standards adopted by the organization. The delivery driver operating to near impossible delivery schedules; the manager agreeing to the strident demands of a large customer regardless of the risks to employees involved, are typical dilemmas facing workers and managers alike. The only way to deal with these issues is to be well organized and agree with the client/ employees ahead of the crisis how they should be prioritized. Rules and procedures should be intelligible, sensible and reasonable. They should be designed to be followed under normal production or service delivery conditions. If following the rules involves very long delays or impossible production schedules, they should be revised rather than ignored by workers and managers alike, until it is too late and an accident occurs. Sometimes the safety rules are simply used in a court of law, in an attempt to defend the company concerned, following the accident. Managers who plan the impossible schedule or ignore a safety rule to achieve production or service demands, are held responsible for the outcomes. It is acceptable to balance the cost of the action against the level of risk being addressed but it is never acceptable to ignore safety rules or standards simply to get the work done. Courts are not impressed by managers who put proﬁt considerations ahead of safety requirements.

Managers and supervisors should plan to have regular discussions to learn about the problems faced by employees and discuss possible solutions. Some meetings, like the safety committee, are speciﬁcally planned for safety matters, but this should be reinforced by discussing health and safety issues at all routine management meetings. Regular one-to-one talks should also take place in the workplace, preferably to a planned theme or safety topic, to get speciﬁc messages across and get feedback from employees.

4.9.4

Competence

Competent people, who know what they are doing and have the necessary skills to do the task correctly and safely, will make the organization effective. Competence can be bought in through recruitment or consultancy but is often much more effective if developed from among employees. It demonstrates commitment to health and safety and a sense of security for the workforce. The loyalty that it develops in the workforce, can be a signiﬁcant beneﬁt to safety standards. Earlier in this chapter there is more detail on how to achieve competence.

4.9.5

Employee representation

Enthusiastic, competent employee safety representatives given the resources and freedom to fulﬁl their function effectively can make a major contribution to good health and safety standards. They can provide the essential bridge between managers and employees. People are more willing to accept the restrictions that some precautions bring if they are consulted and feel involved, either directly in small workforces or through their safety representatives. See earlier in chapter 3 for the details.

4.10 External influences 4.9.3

Communication

Communications are covered in depth earlier in the chapter but clearly will have signiﬁcant inﬂuence on health and safety issues. This will include: ➤ poorly communicated procedures that will not be understood or followed ➤ poor verbal communications which will be misunderstood and will demonstrate a lack of interest by senior managers ➤ missing or incorrect signs may cause accidents rather than prevent them ➤ managers who are nervous about face-to-face discussions with the workforce on health and safety issues will have a negative effect.

The role of external organizations is set out in Chapter 1. Here the inﬂuence they can have is brieﬂy discussed, including societal expectations, legislation and enforcement, insurance companies, trade unions, economics, commercial stakeholders.

4.10.1

Societal expectations

Societal expectations are not static and tend to rise over time, particularly in a wealthy nation like the UK. For example, the standards of safety accepted in a motor car ﬁfty years ago would be considered to be totally inadequate at the beginning of the 21st century. We expect safe, quiet, comfortable cars that do not break down and retain their appearance for many thousands of miles.

63

Introduction to Health and Safety at Work Industry should strive to deliver these same high standards for the health and safety of employees or service providers. The question is whether societal expectations are as great an inﬂuence on workplace safety standards as they are on product safety standards. Society can inﬂuence standards through: ➤ people only working for good employers. This is effective in times of low unemployment ➤ national and local news media highlighting good and bad employment practices ➤ schools teaching good standards of health and safety ➤ the purchase of fashionable and desirable safety equipment, like trendy crash helmets on mountain bikes ➤ only buying products from responsible companies. The difﬁculty of deﬁning what is responsible has been partly overcome through ethical investment criteria but this is possibly not widely enough understood to be a major inﬂuence ➤ watching TV and other programmes which improve safety knowledge and encourage safe behaviour from an early age. It will be interesting to see if ‘Bob the Builder’ and all the books, videos and toys produced to enhance sales will have a positive effect on future building and DIY health and safety standards.

4.10.2

Legislation and enforcement

Good comprehensible legislation should have a positive effect on health and safety standards. Taken together legislation and enforcement can affect standards by: ➤ providing a level to which every employer has to conform ➤ insisting on minimum standards which also enhances peoples’ ability to operate and perform well ➤ providing a tough, visible threat of getting shut down or a heavy ﬁne ➤ stiﬂing development by being too prescriptive. For example, woodworking machines did not develop quickly in the 20th century, partly because the regulations were so detailed in their requirements that new designs were not feasible ➤ providing well presented and easily read guidance for speciﬁc industries at reasonable cost or free. On the other hand a weak enforcement regime can have a powerful negative effect on standards.

4.10.3

Insurance companies

Insurance companies can inﬂuence health and safety standards mainly through ﬁnancial incentives. Employers’ liability insurance is a legal requirement in the UK and therefore all employers have to obtain this type of

64

insurance cover. Insurance companies can inﬂuence standards through: ➤ discounting premiums to those in the safest sectors or best individual companies ➤ insisting on risk reduction improvements to remain insured. This is not very effective where competition for business is ﬁerce ➤ encouraging risk reduction improvements by bundling services into the insurance premium ➤ providing guidance on standards at reasonable cost or free.

4.10.4

Trade unions

Trade unions can inﬂuence standards by: ➤ providing training and education for members ➤ providing guidance and advice cheaply or free to members ➤ inﬂuencing governments to regulate, enhance enforcement activities and provide guidance ➤ inﬂuencing employers to provide high standards for their members. This is sometimes confused with ﬁnancial improvements with health and safety getting a lower priority ➤ encouraging members to work for safer employers ➤ helping members to get proper compensation for injury and ill-health if it is caused through their work.

4.10.5

Economics

Economics can play a major role in inﬂuencing health and safety standards. The following ways are the most common: ➤ lack of orders and/or money can cause employers to try to ignore health and safety requirements ➤ if employers were really aware of the actual and potential cost of accidents and ﬁres they would be more concerned about prevention. The HSE believe that the ratio between insured and uninsured costs of accidents is between 1:8 and 1:36 (see The Costs of Accidents at Work, HSE Books, HSG96) ➤ perversely when the economy is booming activity increases and, particularly in the building industry, accidents can sharply increase. The pressures to perform and deliver for customers can be safety averse ➤ businesses that are only managed on short-term performance indicators seldom see the advantage of the long-term gains that are possible with a happy safe and ﬁt workforce. The cost of accidents and ill-health, in both human and ﬁnancial terms, needs to be visible throughout the

Promoting a positive health and safety culture organization so that all levels of employee are encouraged to take preventative measures.

4.10.6

Commercial stakeholders

A lot can be done by commercial stakeholders inﬂuence standards. This includes: ➤ insisting on proper arrangements for health and safety management at supplier companies before they tender for work or contracts ➤ checking on suppliers to see if the workplace standards are satisfactory ➤ encouraging ethical investments ➤ considering ethical standards as well as ﬁnancial when banks provide funding ➤ providing high quality information for customers ➤ insisting on high standards to obtain detailed planning permission (where this is possible) ➤ providing low cost guidance and advice.

7. (a) Giving a practical example, explain the meaning of the term ‘human error’ (b) Outline individual (or personal) factors that may contribute to human errors occurring at work. 8. Describe, using practical examples, four types of human error that can lead to accidents in the workplace. 9. (a) Outline ways of reducing the likelihood of human error in the workplace (b) Give FOUR reasons why the seriousness of a hazard may be underestimated by someone exposed to it (c) Outline ways in which managers can motivate employees to work safely. 10. Outline the ways in which the health and safety culture of an organization might be improved. 11. Outline the factors that might cause the safety culture within an organization to decline.

4.11 Practice NEBOSH questions for Chapter 4 1. Describe FIVE components of a positive health and safety culture. 2. (a) Define the term ‘accident incidence rate’ (b) Outline how information on accidents could be used to promote health and safety in the workplace. 3. Outline the personal factors that might place an individual at a greater risk of harm while at work. 4. (a) Explain, using an example, the meaning of the term ‘attitude’ (b) Outline THREE inﬂuences on the attitude towards health and safety of employees within an organization

12. Outline the practical means by which a manager could involve employees in the improvement of health and safety in the workplace. 13. Following a signiﬁcant increase in accidents, a health and safety campaign is to be launched within a organization to encourage safer working by employees. (i) Outline how the organization might ensure that the nature of the campaign is effectively communicated to, and understood by, employees (ii) Explain why it is important to use a variety of methods to communicate health and safety information in the workplace (iii) Other than poor communications, describe the organizational factors that could limit the effectiveness of the campaign 14. Give reasons why a verbal instruction may not be clearly understood by an employee.

5. (a) Explain the meaning of the term ‘motivation’ (b) Other than lack of motivation, outline SIX reasons why employees may fail to comply with safety procedures at work (c) Outline ways in which employers may motivate their employees to comply with health and safety procedures.

16. Outline FOUR advantages and FOUR disadvantages of using ‘propaganda’ posters to communicate health and safety information to the workforce.

6. (a) Explain the meaning of the term ‘perception’ (b) Outline the factors relating to the individual that may inﬂuence a person’s perception of an occupational risk (c) Outline ways in which employees’ perceptions of hazards in the workplace might be improved.

17. (a) Identify FOUR types of health and safety information that might usefully be displayed on a notice board with a workplace (b) Explain how the effectiveness of notice boards as a means of communicating health and safety information to the workforce can be maximized.

15. Explain why employees may fail to comply with safety procedures at work.

65

Introduction to Health and Safety at Work 18. Identify a range of methods that an employer can use to provide health and safety information directly to individual employees. 19. (a) Identify the TWO means by which employers may provide information to employees in order to comply with the Health and Safety Information for Employees Regulations 1989 (b) Outline the categories of information provided to employees by the means identiﬁed in (a). 20. Explain how induction training programmes for new employees can help to reduce the number of accidents in the workplace. 21. A contractor has been engaged to undertake building maintenance work in a busy warehouse. Outline the issues that should be covered in an induction programme for the contractor’s employees.

66

22. An independent audit of an organization has concluded that employees have received insufﬁcient health and safety training. (i) Describe the factors that should be considered when developing an extensive programme of health and safety training within an organization (ii) Outline the various measures that might be used to assess the effectiveness of such training (iii) Give FOUR reasons why it is important for an employer to keep a record of the training provided to each employee. 23. Outline reasons why an employee might require additional health and safety training at a later stage of employment within an organization. 24. Describe TWO internal and TWO external inﬂuences on the health and safety culture of an organization.

Risk assessment

5

5.1 Introduction Risk assessment is an essential part of the planning stage of any health and safety management system. HSE, in the publication HSG 65 Successful Health and Safety Management, states that the aim of the planning process is to minimize risks. Risk assessment methods are used to decide on priorities and to set objectives for eliminating hazards and reducing risks. Wherever possible, risks are eliminated through selection and design of facilities, equipment and processes. If risks cannot be eliminated, they are minimized by the use of physical controls or, as a last resort, through systems of work and personal protective equipment.

5.2 Legal aspects of risk assessment The general duties of employers to their employees in section 2 of the Health and Safety at Work Act 1974 imply the need for risk assessment. This duty was also extended by section 3 of the Act to anybody else affected by activities of the employer – contractors, visitors, customers or members of the public. However, the Management of Health and Safety at Work Regulations are much more speciﬁc concerning the need for risk assessment. The following requirements are laid down in those regulations: the risk assessment shall be ‘suitable and sufficient’ and cover both employees and

Figure 5.1 Reducing the risk – finding an alternative to fitting a wall-mounted boiler.

67

Introduction to Health and Safety at Work non-employees affected by the employer’s undertaking (e.g. contractors, members of the public, students, patients, customers, etc.); every self-employed person shall make a ‘suitable and sufficient’ assessment of the risks to which they or those affected by the undertaking may be exposed; any risk assessment shall be reviewed if there is reason to suspect that it is no longer valid or if a significant change has taken place; where there are more than four employees, the significant findings of the assessment shall be recorded and any specially at risk group of employees identified. (This does not mean that employers with four or less employees need not undertake risk assessments.) The term ‘suitable and sufﬁcient’ is important since it deﬁnes the limits to the risk assessment process. A suitable and sufﬁcient risk assessment should: ➤ identify the signiﬁcant risks and ignore the trivial ones; ➤ identify and prioritize the measures required to comply with any relevant statutory provisions; ➤ remain appropriate to the nature of the work and valid over a reasonable period of time. When assessing risks under the Management of Health and Safety at Work Regulations, reference to other regulations may be necessary even if there is no speciﬁc requirement for a risk assessment in those regulations. For example, reference to the legal requirements of the Provision and Use of Work Equipment Regulations will be necessary when risks from the operation of machinery are being considered. However, there is no need to repeat a risk assessment if it is already covered by other regulations (e.g. a risk assessment involving personal protective equipment is required under the COSHH Regulations so there is no need to undertake a separate risk assessment under the Personal Protective Equipment Regulations). Apart from the duty under the Management of Health and Safety at Work Regulations to undertake a health and safety risk assessment of any person (employees, contractors or members of the public), who may be affected by the activities of the organization, the following regulations require a speciﬁc risk assessment to be made: ➤ ➤ ➤ ➤ ➤

Ionising Radiation Regulations Control of Asbestos Regulations The Control of Noise at Work Regulations Manual Handling Operations Regulations Health and Safety (Display Screen Equipment) Regulations

68

➤ The Personal Protective Equipment at Work Regulations ➤ The Conﬁned Spaces Regulations ➤ Work at Height Regulations ➤ The Regulatory Reform (Fire Safety) Order ➤ The Control of Vibration at Work Regulations ➤ Control of Lead at Work Regulations ➤ Control of Substances Hazardous to Health Regulations. A detailed comparison of the risk assessments required for most of these and more specialist regulations is given in the HSE Guide to Risk Assessment Requirements, INDG218.

5.3 Forms of risk assessment There are two basic forms of risk assessment. A quantitative risk assessment attempts to measure the risk by relating the probability of the risk occurring to the possible severity of the outcome and then giving the risk a numerical value. This method of risk assessment is used in situations where a malfunction could be very serious (e.g. aircraft design and maintenance or the petrochemical industry). The more common form of risk assessment is the qualitative assessment, which is based purely on personal judgement and is normally deﬁned as high, medium or low. Qualitative risk assessments are usually satisfactory since the deﬁnition (high, medium or low) is normally used to determine the time frame in which further action is to be taken. The term ‘generic’ risk assessment is sometimes used and describes a risk assessment which covers similar activities or work equipment in different departments, sites or companies. Such assessments are often produced by specialist bodies, such as trade associations. If used, they must be appropriate to the particular job and they will need to be extended to cover additional hazards or risks.

5.4 Some definitions Some basic deﬁnitions were introduced in Chapter 1 and those relevant to risk assessment are reproduced here. Electricity is an example of a high hazard since it has the potential to kill a person. The risk associated with electricity – the likelihood of being killed on coming into contact with an electrical device – is, hopefully, low.

Risk assessment

5.4.1

Hazard and risk

A hazard is the potential of a substance, activity or process to cause harm. Hazards take many forms including, for example, chemicals, electricity and the use of a ladder. A hazard can be ranked relative to other hazards or to a possible level of danger. A risk is the likelihood of a substance, activity or process to cause harm. Risk (or strictly the level of risk) is also linked to the severity of its consequences. A risk can be reduced and the hazard controlled by good management. It is very important to distinguish between a hazard and a risk – the two terms are often confused and activities often called high risk are in fact high hazard. There should only be high residual risk where there is poor health and safety management and inadequate control measures.

5.4.2

Occupational or work-related ill-health

This is concerned with those illnesses or physical and mental disorders that are either caused or triggered by workplace activities. Such conditions may be induced by the particular work activity of the individual or by activities of others in the workplace. The time interval between exposure and the onset of the illness may be short (e.g. asthma attacks) or long (e.g. deafness or cancer).

5.4.3

Accident

Figure 5.2

5.4.5

Accident at work.

Dangerous occurrence

This is a ‘near miss’ which could have led to serious injury or loss of life. Dangerous occurrences are deﬁned in the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995 (often known as RIDDOR) and are always reportable to the Enforcement Authorities. Examples include the collapse of a scaffold or a crane or the failure of any passenger carrying equipment. In 1969, F E Bird collected a large quantity of accident data and produced a well-known triangle (Figure 5.3). It can be seen that damage and near miss accidents occur much more frequently than injury accidents and are, therefore, a good indicator of hazards. The study also shows that most accidents are predictable and avoidable.

This is deﬁned by the Health and Safety Executive as ‘any unplanned event that results in injury or ill-health of people, or damage or loss to property, plant, materials or the environment or a loss of a business opportunity’. Other authorities deﬁne an accident more narrowly by excluding events that do not involve injury or illhealth. This book will always use the Health and Safety Executive deﬁnition.

Serious or disabling injuries 1

10

Minor injuries (first aid injuries)

Damage accidents

5.4.4

30

Near miss

This is any incident that could have resulted in an accident. Knowledge of near misses is very important since research has shown that, approximately, for every 10 ‘near miss’ events at a particular location in the workplace, a minor accident will occur.

Near miss accidents 600

Figure 5.3

F E Bird’s well-known accident triangle.

69

Introduction to Health and Safety at Work 5.5 The objectives of risk assessment The main objective of risk assessment is to determine the measures required by the organization to comply with relevant health and safety legislation and, thereby, reduce the level of occupational injuries and ill-health. The purpose is to help the employer or self-employed person to determine the measures required to comply with their legal statutory duty under the Health and Safety at Work Act 1974 or its associated Regulations. The risk assessment will need to cover all those who may be at risk, such as customers, contractors and members of the public. In the case of shared workplaces, an overall risk assessment may be needed in partnership with other employers. In Chapter 1, the moral, legal and ﬁnancial arguments for health and safety management were discussed in detail. The important distinction between the direct and indirect costs of accidents is reiterated here. Any accident or incidence of ill-health will cause both direct and indirect costs and incur an insured and an uninsured cost. It is important that all of these costs are taken into account when the full cost of an accident is calculated. In a study undertaken by the HSE, it was shown that indirect costs or hidden costs could be 36 times greater than direct costs of an accident. In other words, the direct costs of an accident or disease represent the tip of the iceberg when compared to the overall costs (The Cost of Accidents at Work HSG 96). Direct costs are costs that are directly related to the accident. They may be insured (claims on employers’ and public liability insurance, damage to buildings, equipment or vehicles) or uninsured (ﬁnes, sick pay, damage to product, equipment or process). Indirect costs may be insured (business loss, product or process liability) or uninsured (loss of goodwill, extra overtime payments, accident investigation time, production delays). There are many reasons for the seriousness of a hazard not to be obvious to the person exposed to it. It may be that the hazard is not visible (radiation, certain gases and biological agents) or have no short-term effect (work related upper limb disorders). The common reasons include lack of attention, lack of experience, the wearing of personal protective equipment, sensory impairment and inadequate information, instruction and training.

5.6 Accident categories There are several categories of accident, all of which will be dealt with in more detail in later chapters. The principal categories are as follows: ➤ contact with moving machinery or material being machined

70

➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

struck by moving, ﬂying or falling object hit by a moving vehicle struck against something ﬁxed or stationary injured while handling, lifting or carrying slips, trips and falls on the same level falls from a height trapped by something collapsing drowned or asphyxiated exposed to, or in contact, with a harmful substance exposed to ﬁre exposed to an explosion contact with electricity or an electrical discharge injured by an animal physically assaulted by a person other kind of accident.

5.7 Health risks Risk assessment is not only concerned with injuries in the workplace but also needs to consider the possibility of occupational ill-health. Health risks fall into the following four categories: ➤ ➤ ➤ ➤

chemical (e.g. paint solvents, exhaust fumes) biological (e.g. bacteria, pathogens) physical (e.g. noise, vibrations) psychological (e.g. occupational stress).

There are two possible health effects of occupational ill-health. They may be acute which means that they occur soon after the exposure and are often of short duration, although in some cases emergency admission to hospital may be required. They may be chronic which means that the health effects develop with time. It may take several years for the associated disease to develop and the effects may be slight (mild asthma) or severe (cancer). Health risks are discussed in more detail in Chapter 14.

5.8

The management of risk assessment

Risk assessment is part of the planning and implementation stage of the health and safety management system recommended by the HSE in its publication HSG 65. All aspects of the organization, including health and safety management, need to be covered by the risk assessment process. This will involve the assessment of risk in areas such as maintenance procedures, training programmes and supervisory arrangements. A general risk

Risk assessment assessment of the organization should reveal the signiﬁcant hazards present and the general control measures that are in place. Such a risk assessment should be completed ﬁrst and then followed by more speciﬁc risk assessments that examine individual work activities. HSE has produced a free leaﬂet entitled Five steps to risk assessment. It gives practical advice on assessing risks and recording the ﬁndings and is aimed at small and medium-sized companies in the service and manufacturing sectors. The ﬁve steps are: ➤ look for the hazards ➤ decide who might be harmed, and how ➤ evaluate the risks and decide whether existing precautions are adequate or more should be done ➤ record the signiﬁcant ﬁndings ➤ review the assessment and revise it if necessary. Each of these steps will be examined in turn in the next section. Finally, it is important that the risk assessment team is selected on the basis of its competence to assess risks in the particular areas under examination in the organization. The team leader or manager should have health and safety experience and relevant training in risk assessment. It is sensible to involve the appropriate line manager, who has responsibility for the area or activity being assessed, as a team member. Other members of the team will be selected on the basis of their experience, their technical and/or design knowledge and any relevant standards or regulations relating to the activity or process. At least one team member must have communication and report writing skills. It is likely that team members will require some basic training in risk assessment.

5.9 The risk assessment process The HSE approach to risk assessment (5 steps) will be used to discuss the process of risk assessment. It is, however, easier to divide the process into six elements: ➤ ➤ ➤ ➤ ➤ ➤

hazard identiﬁcation persons at risk evaluation of risk level risk controls (existing and additional) record of risk assessment ﬁndings monitoring and review.

Each element will be discussed in turn.

5.9.1

Hazard identification

Hazard identiﬁcation is the crucial ﬁrst step of risk assessment. Only signiﬁcant hazards, which could result

in serious harm to people, should be identiﬁed. Trivial hazards should be ignored. A tour of the area under consideration by the risk assessment team is an essential part of hazard identiﬁcation as is consultation with the relevant section of the workforce. A review of accident, incident and ill-health records will also help with the identiﬁcation. Other sources of information include safety inspection, survey and audit reports, job or task analysis reports, manufacturers’ handbooks or data sheets and approved codes of practice and other forms of guidance. Hazards will vary from workplace to workplace but the checklist in Appendix 5.1 shows the common hazards that are signiﬁcant in many workplaces. Many questions in the NEBOSH examinations involve several common hazards found in most workplaces. It is important that unsafe conditions are not confused with hazards, during hazard identiﬁcation. Unsafe conditions should be rectiﬁed as soon as possible after observation. Examples of unsafe conditions include missing machine guards, faulty warning systems and oil spillage on the workplace ﬂoor.

5.9.2

Persons at risk

Employees and contractors who work full time at the workplace are the most obvious groups at risk and it will be necessary check that they are competent to perform their particular tasks. However, there may be other groups who spend time in or around the workplace. These include young workers, trainees, new and expectant mothers, cleaners, contractor and maintenance workers and members of the public. Members of the public will include visitors, patients, students or customers as well as passers by. The risk assessment must include any additional controls required due to the vulnerability of any of these groups, perhaps caused by inexperience or disability. It must also give an indication of the numbers of people from the different groups who come into contact with the hazard and the frequency of these contacts.

5.9.3

Evaluation of risk level

During most risk assessment it will be noted that some of the risks posed by the hazard have already been addressed or controlled. The purpose of the risk assessment, therefore, is to reduce the remaining risk. This is called the residual risk. The goal of risk assessment is to reduce all residual risks to as low a level as reasonably practicable. In a relatively complex workplace, this will take time so that a system of ranking risk is required – the higher the risk level the sooner it must be addressed and controlled.

71

Introduction to Health and Safety at Work For most situations, a qualitative risk assessment will be perfectly adequate. (This is certainly the case for NEBOSH Certiﬁcate candidates and is suitable for use during the practical assessment.) During the risk assessment, a judgement is made as to whether the risk level is high, medium or low in terms of the risk of somebody being injured. This designation deﬁnes a timetable for remedial actions to be taken thereby reducing the risk. High-risk activities should normally be addressed in days, medium risks in weeks and low risks in months or in some cases no action will be required. It will usually be necessary for risk assessors to receive some training in risk level designation. A quantitative risk assessment attempts to quantify the risk level in terms of the likelihood of an incident and its subsequent severity. Clearly the higher the likelihood and severity, the higher the risk will be. The likelihood depends on such factors as the control measures in place, the frequency of exposure to the hazard and the category of person exposed to the hazard. The severity will depend on the magnitude of the hazard (e.g. voltage, toxicity, etc.). HSE suggest in HSG 65 a simple 33 matrix to determine risk levels.

A risk management matrix has been developed which combines these two risk levels as shown below.

Likelihood of occurrence Harm is certain or near certain to occur Harm will often occur Harm will seldom occur

The next stage in the risk assessment is the control of the risk. In established workplaces, some control of risk will already be in place. The effectiveness of these controls needs to be assessed so that an estimate of the residual risk may be made. Many hazards have had speciﬁc acts, regulations or other recognized standards developed to reduce associated risks. Examples of such hazards are ﬁre, electricity, lead and asbestos. The relevant legislation and any accompanying approved codes of practice or guidance should be consulted ﬁrst and any recommendations implemented. Advice on control measures may also be available from trade associations, trade unions or employers’ organizations. Where there are existing preventative measures in place, it is important to check that they are working properly and that everybody affected has a clear understanding of the measures. It may be necessary to strengthen existing procedures, for example, by the introduction of a permit to work system. More details on the principles of control are contained in Chapter 6.

Severity of harm Death or major injury (as deﬁned by RIDDOR) 3 day injury or illness (as deﬁned by RIDDOR) All other injuries or illnesses Risk ⴝ Severity ⴛ Likelihood

Likelihood

Likelihood level High 3 Medium 2 Low 1 Severity level Major 3 Serious 2 Slight 1

Severity Slight 1

Serious 2

Major 3

Low 1

Low 1

Low 2

Medium 3

Medium 2

Low 2

Medium 4

High 6

Medium 3

High 6

High 9

High 3

Thus: 6–9 High risk 3–4 Medium risk 1–2 Low risk

It is possible to apply such methods to organizational risk or to the risk that the management system for health and safety will not deliver in the way in which it was expected or required. Such risks will add to the activity or occupational risk level. In simple terms, poor supervision of an activity will increase its overall level of risk.

72

Occupational risk level

Organizational risk level

L Low risk

Low

Medium

High

Low

L

L

M

Medium

L

M

H

High

M

H

Unsatisfactory

M Medium risk

H High risk

Whichever type of risk evaluation method is used, the level of risk simply enables a timetable of risk reduction to be formulated. The legal duty requires that all risks should be reduced to as low as is reasonably practicable.

5.9.4

Risk control measures

Hierarchy of risk control When assessing the adequacy of existing controls or introducing new controls, a hierarchy of risk controls should be considered. The Management of Health and Safety at Work Regulations 1999 Schedule 1 speciﬁes the general principles of prevention which are set out in the European Council Directive. These principles are: 1. 2.

Avoiding risks Evaluating the risks which cannot be avoided

Risk assessment 3. 4.

5. 6. 7.

8. 9.

Combating the risks at source Adapting the work to the individual, especially as regards the design of the workplace, the choice of work equipment and the choice of working and production methods, with a view, in particular, to alleviating monotonous work and work at a predetermined work-rate and to reducing their effects on health Adapting to technical progress Replacing the dangerous by the non-dangerous or the less dangerous Developing a coherent overall prevention policy which covers technology, organization of work, working conditions, social relationships and the inﬂuence of factors relating to the working environment Giving collective protective measures priority over individual protective measures and Giving appropriate instruction to employees.

These principles are not exactly a hierarchy but must be considered alongside the usual hierarchy of risk control which is as follows: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

elimination substitution changing work methods/patterns reduced or limited time exposure engineering controls (e.g. isolation, insulation and ventilation) good housekeeping safe systems of work training and information personal protective equipment welfare monitoring and supervision review.

Prioritization of risk control The prioritization of the implementation of risk control measures will depend on the risk rating (high, medium and low) but the time scale in which the measures are introduced will not always follow the ratings. It may be convenient to deal with a low level risk at the same time as a high level risk or before a medium level risk. It may also be that work on a high risk control system is delayed due to a late delivery of an essential component – this should not halt the overall risk reduction work. It is important to maintain a continuous programme of risk improvement rather than slavishly following a predetermined priority list.

5.9.5

Record of risk assessment findings

It is very useful to keep a written record of the risk assessment even if there are less than ﬁve employees in the organization. For an assessment to be ‘suitable and

sufﬁcient’ only the signiﬁcant hazards and conclusions need be recorded. The record should also include details of the groups of people affected by the hazards and the existing control measures and their effectiveness. The conclusions should identify any new controls required and a review date. The HSE booklet Five steps to risk assessment provides a very useful guide and examples of the detail required for most risk assessments. There are many other possible layouts which can be used for the risk assessment record. One example is given in Appendix 5.2. The written record provides excellent evidence to a health and safety inspector of compliance with the law. It is also useful evidence if the organization should become involved in a civil action. The record should be accessible to employees and a copy kept with the safety manual containing the safety policy and arrangements.

5.9.6

Monitoring and review

As mentioned earlier, the risk controls should be reviewed periodically. This is equally true for the risk assessment as a whole. Review and revision may be necessary when conditions change as a result of the introduction of new machinery, processes or hazards. There may be new information on hazardous substances or new legislation. There could also be changes in the workforce, for example, the introduction of trainees. The risk assessment only needs to be revised if signiﬁcant changes have taken place since the last assessment was done. An accident or incident or a series of minor ones provides a good reason for a review of the risk assessment. This is known as the post-accident risk assessment.

5.10 Special cases There are several groups of persons who require an additional risk assessment due to their being more ‘at risk’ than other groups. Three such groups will be considered – young persons, expectant and nursing mothers and disabled workers.

5.10.1

Young persons

There were 21 fatalities of young people at work in 2002/03 and more recent ﬁgures have not shown much of an improvement. A risk assessment involving young people needs to consider the particular vulnerability of young persons in the workplace. Young workers clearly have a lack of experience and awareness of risks in the workplace, a tendency to be subject to peer pressure and a willingness

73

Introduction to Health and Safety at Work to work hard. Many young workers will be trainees or on unpaid work experience. Young people are not fully developed and are more vulnerable to physical, biological and chemical hazards than adults. An amendment to the Health and Safety at Work Act enables trainees on Government sponsored training schemes to be treated as employees as far as health and safety is concerned. The Management of Health and Safety at Work Regulations deﬁnes a young person as anybody under the age of 18 years and stipulates that a special risk assessment must be completed, which takes into account their immaturity and inexperience. The assessment must be completed before the young person starts work. If the young person is of school age (16 years or less), the parents or guardian of the child should be notiﬁed of the outcome of the risk assessment and details of any safeguards which will be used to protect the health and safety of the child. The following key elements should be covered by the risk assessment: ➤ details of the work activity, including any equipment or hazardous substances ➤ details of any prohibited equipment or processes ➤ details of health and safety training to be provided ➤ details of supervision arrangements. The extent of the risks identiﬁed in the risk assessment will determine whether employers should restrict the work of the people they employ. Except in special circumstances, young people should not be employed to do work which: ➤ is beyond their physical or psychological capacity ➤ exposes them to substances chronically harmful to human health, e.g. toxic or carcinogenic substances, or effects likely to be passed on genetically or likely to harm the unborn child ➤ exposes them to radiation ➤ involves a risk of accidents which they are unlikely to recognize because of e.g. their lack of experience, training or attention to safety ➤ involves a risk to their health from extreme heat, noise or vibration. These restrictions will not apply in ’special circumstances’ where young people over the minimum school leaving age are doing work necessary for their training, under proper supervision by a competent person, and providing the risks are reduced to the lowest level, so far as is reasonably practicable. Under no circumstances can children of compulsory school age do work involving these risks, whether they are employed or under training such as work experience.

74

Induction training is important for young workers and such training should include site rules, restricted areas, prohibited machines and processes, ﬁre precautions and details of any further training related to their particular job. At induction, they should be introduced to their mentor and given close supervision, particularly during the ﬁrst few weeks of their employment. A guide is available to employers who organize site visits for young people. The guide (www.safevisits.org. uk) gives practical advice and a checklist that can be used during the organization of the visit. More detailed guidance is available from HSE Books – HSG 165 ‘Young people at work’ and HSG 199 ‘Managing health and safety on work experience’.

5.10.2

Expectant and nursing mothers

The Management of Health and Safety at Work Regulations 1999 incorporates the Pregnant Workers Directive from the EU. If any type of work could present a particular risk to expectant or nursing mothers, the risk assessment must include an assessment of such risks. Should these risks be unavoidable, then the woman’s working conditions or hours must be altered to avoid the risks. The alternatives are for her to be offered other work or be suspended from work on full pay. The woman must notify the employer in writing that she is pregnant, or has given birth within the previous six months and/or is breastfeeding. Pregnant workers should not be exposed to chemicals such as pesticides and lead or to biological hazards, such as hepatitis. Female agricultural workers, veterinaries or farmer’s wives who are pregnant, should not assist with lambing so that any possible contact with ovine chlamydial is avoided. Typical factors which might affect such women are: ➤ ➤ ➤ ➤ ➤ ➤ ➤

manual handling chemical or biological agents ionising radiation passive smoking lack of rest room facilities temperature variations ergonomic issues related to prolonged standing, sitting or the need for awkward body movement ➤ issues associated with the use and wearing of personal protective equipment ➤ working excessive hours ➤ stress and violence to staff. Detailed guidance is available in New and expectant mothers at work, HSG 122, HSE Books.

5.10.3

Workers with a disability

Organizations have been encouraged for many years to employ workers with disabilities and to ensure that

Risk assessment their premises provide suitable access for such people. From a health and safety point of view, it is important that workers with a disability are covered by special risk assessments so that appropriate controls are in place to protect them. For example, employees with a hearing problem will need to be warned when the ﬁre alarm sounds or a fork lift truck approaches. Special vibrating signals or ﬂashing lights may be used. Similarly workers in wheelchairs will require a clear, wheelchair friendly, route to a ﬁre exit and onwards to the assembly point. Safe systems of work and welfare facilities need to be suitable for any workers with disabilities. The ﬁnal stage of the goods and services provisions in Part III of the Disability Discrimination Act came into force on 1 October 2004. The new duties apply to service providers where physical features make access to their services impossible or unreasonable for people with a disability. The Act requires equal opportunities for employment and access to workplaces to be extended to all people with disabilities.

5.10.4

Lone workers

People who work alone, like those in small workshops, remote areas of a large site, social workers, sales personnel or mobile maintenance staff, should not be at more risk than other employees. It is important to consider whether the risks of the job can be properly controlled by one person. Other considerations in the risk assessment include: ➤ whether the particular workplace presents a special risk to someone working alone

➤ is there safe egress and exit from the workplace? ➤ can all the equipment and substances be safely handled by one person? ➤ is violence from others a risk? ➤ would women and young persons be specially at risk? ➤ is the worker medically ﬁt and suitable for working alone? ➤ are special training and supervision required? For details of further precautions for lone workers, see paragraph 6.6 of Chapter 6.

5.11 Practice NEBOSH questions for Chapter 5 1. (a) Explain, using examples, the meaning of the following terms: (i) hazard (ii) risk (b) Outline the key stages of a general risk assessment (c) Give THREE reasons why the seriousness of a hazard may not be obvious to someone exposed to it (d) Outline the logical steps to take in managing risks at work. 2. (a) Identify the particular requirements of Regulation 3 of the Management of Health and Safety at Work Regulations 1999 in relation to an employer’s duty to carry out risk assessments (b) Outline the factors that should be considered when selecting individuals to assist in carrying out risk assessments in the workplace. 3. A factory manager intends to introduce a new work process for which a risk assessment is required under Regulation 3 of the Management of Health and Safety at Work Regulations 1999. (i) Outline the factors that should be used in carrying out the risk assessment, identifying the issues that would need to be considered at EACH stage (ii) Explain the criteria that must be met of the assessment to be deemed ‘suitable and sufﬁcient’ (iii) Identify the various circumstances that may require a review of the risk assessment at a later date.

Figure 5.4 required.

A lone worker – special arrangements are

4. With respect to undertaking general risk assessments on activities within a workplace: (i) outline the FIVE key stages of the risk assessment process, identifying the issues that would need to be considered at EACH stage

75

Introduction to Health and Safety at Work (ii) identify FOUR items of information from within and FOUR items of information from outside the organization that may be useful when assessing the activities (iii) state the legal requirements for recording workplace risk assessments.

11. (a) Identify FOUR ‘personal’ factors that may place young persons at a greater risk from workplace hazards (b) Outline FOUR measures that could be taken to minimize the risks to young persons in the workplace.

5. (a) Identify the ‘five’ steps involved in the assessment of risk from workplace activities (as described in HSE’s “Five steps to risk assessment” (INDG 163)) (b) Explain the criteria that should be applied to help develop an action plan to prioritize the control of health and safety risks in the workplace.

12. Outline the factors that may increase risks to pregnant employees.

6. Outline the hazards that might be encountered in a busy hotel kitchen.

13. (a) Outline three work activities that may present a particular risk to pregnant women (b) Outline the actions that an employer may take when a risk to a new or expectant mother cannot be avoided.

7. Identify SIX hazards that might be considered when assessing the risk to health and safety of a multistorey car park attendant.

14. An employee who works on a production line has notiﬁed her employer that she is pregnant. Outline the factors that the employer should consider when undertaking a speciﬁc risk assessment in relation to this employee.

8. Outline the hazards that might be encountered by a gardener employed by a local authority parks department.

15. Outline the issues to be considered to ensure the health and safety of disabled workers in the workplace.

9. Outline the content of a training course for staff who are required to assist in carrying out risk assessments.

16. Identify the factors to be considered to ensure the health and safety of persons who are required to work on their own away from the workplace.

10. An employer has agreed to accept a young person on a work experience placement for one week. Outline the factors that the employer should consider prior to the placement.

17. Outline the issues that should be considered to ensure the health and safety of cleaners employed in a school out of normal working hours.

76

Risk assessment Appendix 5.1

Hazard checklist

The following checklist may be helpful

1. Equipment/mechanical Entanglement Friction/abrasion Cutting Shearing Stabbing/puncturing Impact Crushing Drawing-in Air or high pressure ﬂuid injection Ejection of parts Pressure/vacuum Display screen equipment Hand tools 2. Transport Works vehicles Mechanical handling People/vehicle interface 3. Access Slips, trips and falls Falling or moving objects Obstruction or projection Working at height Conﬁned spaces Excavations 4. Handling/lifting Manual handling Mechanical handling 5. Electricity Fixed installation Portable tools and equipment 6. Chemicals Dust/fume/gas Toxic Irritant Sensitizing Corrosive Carcinogenic Nuisance

7. Fire and Explosion Flammable materials/gases/ liquids Explosion Means of escape/alarms/detection 8. Particles and dust Inhalation Ingestion Abrasion of skin or eye 9. Radiation Ionising Non-ionising 10. Biological Bacterial Viral Fungal 11. Environmental Noise Vibration Light Humidity Ventilation Temperature Overcrowding 12. The individual Individual not suited to work Long hours High work rate Violence to staff Unsafe behaviour of individual Stress Pregnant/nursing women Young people 13. Other factors to consider Poor maintenance Lack of supervision Lack of training Lack of information Inadequate instruction Unsafe systems

77

Introduction to Health and Safety at Work Appendix 5.2

Example of a risk assessment record

General Health and Safety Risk Assessment

No

Firm/Company

Department

Contact Name

Nature of Business

Telephone Number Principal Hazards Risks to employees and members of the public could arise due to the following hazards: 1. hazardous substances 2. electricity 3. ﬁre 4. dangerous occurrences or other emergency incidents 5. 6. Persons at Risk Employees, contractors, and members of the public. Main Legal Requirements Main Legal Requirements 1. Health and Safety at Work Act 1974 – Section 2 and 3 2. Management of Health and Safety at Work Regulations 1999 3. The Noise at Work Regulations 1989 4. Common Law Duty of Care 5. ? Significant Risks • Acute and chronic health problems caused by the use or release of hazardous substances. • Injuries to employees and members of the public due to equipment failure such as electric shock. • Injuries to employees and members of the public from slips, trips and falls. • Injuries to employees and members of the public caused by ﬁre. • ? Consequences Fractures, bruising, smoke inhalation and burns, acute and chronic health problems and death.

78

Risk assessment

Existing Control Measures Possible examples include: 1. All sub-contractors are vetted prior to appointment. 2. All hazardous and harmful materials are identiﬁed and the risks to people assessed. COSHH assessments are provided and the appropriate controls are implemented. Health surveillance is provided as necessary. 3. Fire risk assessment has been produced. Fire procedures are in place and all employees are trained to deal with ﬁre emergencies. A carbon dioxide ﬁre extinguisher is available at every work site. 4. A minimum of ﬂammable substances are used on the premises, no more than a half days supply at a time. Kept in ﬁre resistant store. 5. No smoking is allowed on the premises. 6. Manual handling is kept to a minimum. Where there is a risk of injury manual handling assessments are carried out. 7. Method statements are used for complex and/or hazardous jobs and are followed at all times. 8. All accidents on or around the site are reported and investigated by management. Any changes found necessary are quickly implemented. All accidents, reportable under RIDDOR 1995, are reported to the HSE on form F2508. 9. At least 1 qualiﬁed First Aider is available during working hours. 10. ? Residual Risk i.e. after controls are in place. Severity ..................................... Likelihood ...................................

Residual Risk .......................................

Information Details of various relevant HSE and trade publications. Comments from Line Manager

Comments from the Risk Assessor

Signed ............................

Signed ...........................

Date .............................

Date ..............................

Review Date

Likelihood

Severity Slight 1

Serious 2

Major 3

Low 1

Low 1

Low 2

Medium 3

Medium 2

Low 2

Medium 4

High 6

Medium 3

High 6

High 9

High 3

79

6

Principles of control

6.1 Introduction The control of risks is essential to secure and maintain a healthy and safe workplace which complies with the relevant legal requirements. Hazard identiﬁcation and risk assessment are covered in Chapter 5 and these together with appropriate risk control measures form the core of HSG 65 ‘implementing and planning’ section of the management model. Chapter 1 covers this in more detail. This chapter concerns the principles that should be adopted when deciding on suitable measures to eliminate or control both acute and chronic risks to the health and safety of people at work. The principles of control can be applied to both health risks and

safety risks, although health risks have some distinctive features that require a special approach. Chapters 9 to 16 deal with speciﬁc workplace hazards and controls subject by subject. The principles of prevention now enshrined in the Management of Health and Safety at Work (MHSW) Regulations need to be used jointly with the hierarchy of control methods which give the preferred order of approach to risk control. When risks have been analysed and assessed, decisions can be made about workplace precautions. All ﬁnal decisions about risk control methods must take into account the relevant legal requirements, which establish minimum levels of risk prevention or control. Some of the duties imposed by the HSW Act and the relevant statutory provisions are absolute and must be complied with. Many requirements are, however, qualiﬁed by the words, so far as is reasonably practicable, or so far as is practicable. These require an assessment of cost, along with information about relative costs, effectiveness and reliability of different control measures. Further guidance on the meaning of these three expressions is provided in Chapter 1.

6.2 Principles of prevention

Figure 6.1

80

When controls break down.

The MHSW Regulations Schedule 1 speciﬁes the general principles of prevention which are set out in article 6(2) of the European Council Directive 89/391/EEC. For the ﬁrst time the principles have been enshrined directly in regulations which state, at Regulation 4, that Where an employer implements any preventative measures he

Principles of control shall do so on the basis of the principles specified in Schedule 1. These principles are: 1.

Avoiding risks This means, for example, trying to stop doing the task or using different processes or doing the work in a different safer way.

2.

Evaluating the risks which cannot be avoided This requires a risk assessment to be carried out.

3.

Combating the risks at source This means that risks, such as a dusty work atmosphere, are controlled by removing the cause of the dust rather than providing special protection; or that slippery ﬂoors are treated or replaced rather than putting up a sign.

4.

Adapting the work to the individual, especially as regards the design of the workplace, the choice of work equipment and the choice of working and production methods, with a view, in particular, to alleviating monotonous work and work at a predetermined work-rate and to reducing their effect on health This will involve consulting those who will be affected when workplaces, methods of work and safety procedures are designed. The control individuals have over their work should be increased, and time spent working at predetermined speeds and in monotonous work should be reduced where it is reasonable to do so.

5.

6.

7.

Adapting to technical progress It is important to take advantage of technological and technical progress, which often gives designers and employers the chance to improve both safety and working methods. With the Internet and other international information sources available a very wide knowledge, going beyond what is happening in the UK or Europe, will be expected by the enforcing authorities and the courts. Replacing the dangerous by the non-dangerous or the less dangerous This involves substituting, for example, equipment or substances with non-hazardous or less hazardous substances. Developing a coherent overall prevention policy which covers technology, organization of work, working conditions, social relationships and the inﬂuence of factors relating to the working environment Health and safety policies should be prepared and applied by reference to these principles.

8.

Giving collective protective measures priority over individual protective measures This means giving priority to control measures which make the workplace safe for everyone working there so giving the greatest beneﬁt, for example, removing hazardous dust by exhaust ventilation rather than providing a ﬁltering respirator to an individual worker. This is sometimes known as a ‘Safe Place’ approach to controlling risks.

9.

Giving appropriate instruction to employees This involves making sure that employees are fully aware of company policy, safety procedures, good practice, ofﬁcial guidance, any test results and legal requirements. This is sometimes known as a ‘Safe Person’ approach to controlling risks where the focus is on individuals. A properly set up health and safety management system should cover and balance both a Safe Place and Safe Person approach.

6.3 Hierarchy of risk control When assessing the adequacy of existing controls or introducing new controls, a hierarchy of risk controls should be considered. The principles of prevention in the MHSW Regulations are not exactly a hierarchy, but must be considered alongside the usual hierarchy of risk controls, which is as follows: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

elimination substitution changing work methods/patterns reduced or limited time exposure engineering controls (e.g. isolation, insulation and ventilation) good housekeeping safe systems of work training and information personal protective equipment welfare monitoring and supervision review.

6.3.1

Elimination or substitution

This is the best and most effective way of avoiding a severe hazard and its associated risks. Elimination occurs when a process or activity is totally abandoned because the associated risk is too high. Substitution describes the use of a less hazardous form of the substance. There are many examples of substitution, such as the use of waterbased rather than oil-based paints, the use of asbestos

81

Introduction to Health and Safety at Work substitutes and the use of compressed air as a power source rather than electricity. Care must be taken not to introduce additional hazards and risks as a result of a substitution.

6.3.2

Changing work methods/patterns

6.3.4

This describes the control of risks by means of engineering design rather than a reliance on preventative actions by the employee. There are several ways of achieving such controls:

In some cases it is possible to change the method of working so that exposures are reduced. For example use rods to clear drains instead of strong chemicals; use disposable hooks for holding articles being sprayed instead of exposing people during the cleaning of reusable hooks. Sometimes the pattern of work can be changed so that people can do things in a more natural way, for example when removing components and packing them consider whether people are right or left handed; encourage people in ofﬁces to take breaks from computer screens by getting up to photocopy, fetch ﬁles or printed documents.

1.

6.3.3

6.3.5

Reduced time exposure

This involves reducing the time during the working day that the employee is exposed to the hazard, either by giving the employee other work or rest periods. It is only suitable for the control of health hazards associated with, for example, noise, display screens and hazardous substances. However, it is important to note that for many hazards there are short-term exposure limits as well as normal working workplace exposure limits (WELS) over an 8-hour period (see Chapter 14). Shortterm limits must not be exceeded during the reduced time exposure intervals.

2.

control the risks at the source (e.g. the use of more efﬁcient dust ﬁlters or the purchase of less noisy equipment) control the risk of exposure by: – isolating the equipment by the use of an enclosure, a barrier or guard – insulating any electrical or temperature hazard – ventilate away any hazardous fumes or gases, either naturally or by the use of extractor fans and hoods.

82

Proper control of gases and vapours in a

Housekeeping

Housekeeping is a very cheap and effective means of controlling risks. It involves keeping the workplace clean and tidy at all times and maintaining good storage systems for hazardous substances and other potentially dangerous items. The risks most likely to be inﬂuenced by good housekeeping are ﬁre and slips, trips and falls.

6.3.6

Safe systems of work

A safe system of work is a requirement of the HSW Act and is dealt with in detail later. The system of work describes the safe method of performing the job activity. If the risks involved are high or medium, the details of the system should be in writing and should be communicated to the employee formally in a training session. Systems for low risk activities may be conveyed verbally. There should be records that the employee (or contractor) has been trained or instructed in the safe system of work and that he or she understands it and will abide by it.

6.3.7

Figure 6.2 laboratory.

Engineering controls

Training and information

Both these topics are important but should not be used in isolation. Information includes such items as signs, posters, systems of work and general health and safety arrangements. Details on the categories and design of safety signs are given in Chapter 17 (Health and Safety [Safety Signs and Signals] Regulations 1996).

Principles of control 6.3.8

Personal protective equipment

Personal protective equipment (PPE) should only be used as a last resort. There are many reasons for this. The most important limitations are that PPE: ➤ only protects the person wearing the equipment not others nearby ➤ relies on people wearing the equipment at all times ➤ must be used properly ➤ must be replaced when it no longer offers the correct level of protection. This last point is particularly relevant when respiratory protection is used. The beneﬁts of PPE are: ➤ it gives immediate protection to allow a job to continue while engineering controls are put in place ➤ in an emergency it can be the only practicable way of effecting rescue or shutting down plant in hazardous atmospheres ➤ it can be used to carry out work in conﬁned spaces where alternatives are impracticable. But it should never be used to allow people to work in dangerous atmospheres, which are, for example, enriched with oxygen or explosive.

Figure 6.4

sanitation and washing facilities. There is also a requirement to provide eating and rest rooms. Risk control may be enhanced by the provision of eye washing and shower facilities for use after certain accidents. Within this area of welfare, ﬁrst aid and health surveillance are important services that should be available.

6.3.10

Figure 6.3

PPE used for loading a textile dye vessel.

(See Chapter 14, Section 14.9.5 for more details on personal protective equipment.)

6.3.9

Welfare

Welfare facilities include general workplace ventilation, lighting and heating and the provision of drinking water,

Welfare – washing facilities.

Monitoring and supervision

All risk control measures, whether they rely on engineered or human behavioural controls, must be monitored for their effectiveness and supervised to ensure that they have been applied correctly. Competent people, who have a sound knowledge of the equipment or process, should undertake monitoring. Checklists are useful to ensure that no signiﬁcant factor is forgotten. Any statutory inspection or insurance company reports should be checked to see whether any areas of concern were highlighted and if any recommendations were implemented. Details of any accidents, illnesses or other incidents will give an indication of the effectiveness of the risk control measures. Any emergency arrangements should be tested during the monitoring phase, including ﬁrst aid provision. It is crucial that the operator should be monitored to ascertain that all relevant procedures have been understood and followed. The operator may also be able to suggest improvements to the equipment or system of work. The supervisor is an important source of information during the monitoring process.

83

Introduction to Health and Safety at Work Where the organization is involved with shift work, it is essential that the risk controls are monitored on all shifts to ensure the uniformity of application. The effectiveness and relevance of any training or instruction given should be monitored.

6.3.11

Review

Periodically the risk control measures should be reviewed. Monitoring and other reports are crucial for the review to be useful. Reviews often take place at safety committee and/or at management meetings. A serious accident or incident should lead to an immediate review of the risk control measures in place.

Risks to health from work activities include: ➤ skin contact with irritant substances, leading to dermatitis etc. ➤ inhalation of respiratory sensitizers, triggering immune responses such as asthma ➤ badly designed workstations requiring awkward body postures or repetitive movements, resulting in upper limb disorders, repetitive strain injury and other musculoskeletal conditions ➤ noise levels which are too high, causing deafness and conditions, such as tinnitus ➤ too much vibration, for example, from hand-held tools leading to hand – arm vibration syndrome and circulatory problems

6.4 Controlling health risks 6.4.1

Types of health risk

The principles of control for health risks are the same as those for safety. However, the nature of health risks can make the link between work activities and employee ill-health less obvious than in the case of injury from an accident. The COSHH Amendment Regulations 2005 sets out the principles of control (see box). Figure 6.6 shows a route map for achieving adequate control. Unlike safety risks, which can lead to immediate injury, the results of daily exposure to health risks may not manifest itself for months, years and, in some cases, decades. Irreversible health damage may occur before any symptoms are apparent. It is, therefore, essential to develop a preventive strategy to identify and control risks before anyone is exposed to them.

Figure 6.5

84

Health risk – checking on the contents.

Principles of good practice for the control of exposure to substances hazardous to health (a) Design and operate processes and activities to minimize emission, release and spread of substances hazardous to health. (b) Take into account all relevant routes of exposure – inhalation, skin absorption and ingestion – when developing control measures. (c) Control exposure by measures that are proportionate to the health risk. (d) Choose the most effective and reliable control options which minimize the escape and spread of substances hazardous to health. (e) Where adequate control of exposure cannot be achieved by other means, provide, in combination with other control measures, suitable personal protective equipment. (f) Check and review regularly all elements of control measures for their continuing effectiveness. (g) Inform and train all employees on the hazards and risks from the substances with which they work and the use of control measures developed to minimize the risks. (h) Ensure that the introductin of control measures does not increase the overall risk to health and safety.

Principles of control

What substances (products) do you use?

What are the health hazards (see R-phrases on Safety Data Sheets and/or product label)?

Are you following the principles of good control practice? Or Are your controls equivalent to those suggested by COSHH Essentials? Or Can you demonstrate your controls are adequate?

Figure 6.6

Yes

Don't know

No

Maintain current controls

Seek advice e.g. COSHH Essentials or equivalent

Route map for adequate control for SMEs/non-experts.

➤ exposure to ionising and non-ionising radiation including ultraviolet in the sun’s rays, causing burns, sickness and skin cancer ➤ infections ranging from minor sickness to lifethreatening conditions, caused by inhaling or being contaminated by microbiological organisms ➤ stress causing mental and physical disorders.

➤ ➤ ➤ ➤

Some illnesses or conditions, such as asthma and back pain, have both occupational and non-occupational causes and it may be difﬁcult to establish a deﬁnite causal link with a person’s work activity or their exposure to particular agents or substances. But, if there is evidence that shows the illness or condition is prevalent among the type of workers to which the person belongs or among workers exposed to similar agents or substances, it is likely that their work and exposure has contributed in some way.

6.4.2

Investigate improvements (apply COSHH Essentials guidance or equivalent)

Control hierarchy for exposure to substances hazardous to health

The following shows how the general principles and hierarchy can be applied to substances hazardous to health, which come under the COSHH Regulations: ➤ change the process or task so that there is no need for the hazardous substance ➤ replace the substance with a safer material ➤ use the substance in a safer form, for example, in liquid or pellets to prevent dust from powders. The HSE has produced a useful booklet on 7 steps to

➤

successful substitution of hazardous substances HSG 110, HSE Books, which should be consulted totally enclose the process partially enclose the process and use local exhaust ventilation to extract the harmful substance provide high quality general ventilation, if individual exposures do not breach the exposure limits use safe systems of work and procedures to minimize exposures, spillage or leaks reduce the number of people exposed or the duration of their exposure.

If none of the above control measures prove to be adequate on their own, PPE should be provided. This is a last resort and is only permitted by the COSHH Regulations in conjunction with other means of control if they prove inadequate. Special control requirements are needed for carcinogens, which are set out in the Carcinogen Approved Code of Practice.

6.4.3

Assessing exposure and health surveillance

Some aspects of health exposure will need input from specialist or professional advisers, such as occupational health hygienists, nurses and doctors. However, considerable progress can be made by taking straightforward measures such as: ➤ consulting the workforce on the design of workplaces ➤ talking to manufacturers and suppliers of substances and work equipment about minimizing exposure

85

Introduction to Health and Safety at Work ➤ enclosing machinery to cut down dust, fume and noise ➤ researching the use of less hazardous substances ➤ ensuring that employees are given appropriate information and are trained in the safe handling of all the substances and materials to which they may be exposed. To assess health risks and to make sure that control measures are working properly, it may be necessary, for example, to measure the concentration of substances in air to make sure that exposures remain within the assigned Workplace Exposure Limits (WELs). Sometimes health surveillance of workers who may be exposed will be needed. This will enable data to be collected to check control measures and for early detection of any adverse changes to health. Health surveillance procedures available include biological monitoring for bodily uptake of substances, examination for symptoms and medical surveillance – which may entail clinical examinations and physiological or psychological measurements by occupationally qualiﬁed registered medical practitioners. The procedure chosen should be suitable for the case concerned. Sometimes a method of surveillance is speciﬁed for a particular substance, for example, in the COSHH ACOP. Whenever surveillance is undertaken, a health record has to be kept for the person concerned. Health surveillance should be supervised by a registered medical practitioner or, where appropriate, it should be done by a suitably qualiﬁed person (e.g. an occupational nurse). In the case of inspections for easily detectable symptoms like chrome ulceration or early signs of dermatitis, health surveillance should be done by a suitably trained responsible person. If workers could be exposed to substances listed in Schedule 6 of the COSHH Regulations, medical surveillance, under the supervision of an HSE employment medical adviser or a doctor appointed by HSE, is required.

6.5 Safe systems of work 6.5.1

What is a safe system of work?

A safe system of work has been deﬁned as: The integration of personnel, articles and substances in a laid out and considered method of working which takes proper account of the risks to employees and others who may be affected, such as visitors and contractors, and provides a formal framework to ensure that all of the steps necessary for safe working have been anticipated and implemented.

86

Multi-padlockable hasp for locking off isolating valve

Figure 6.7 tion valve.

Multi-padlocked hasp for locking off an isola-

In simple terms, a safe system of work is a deﬁned method for doing a job in a safe way. It takes account of all foreseeable hazards to health and safety and seeks to eliminate or minimize these. Safe systems of work are normally formal and documented, for example, in written operating procedures but, in some cases, they may be verbal. The particular importance of safe systems of work stems from the recognition that most accidents are caused by a combination of factors (plant, substances, lack of training, supervision, etc.). Hence prevention must be based on an integral approach and not one which only deals with each factor in isolation. The adoption of a safe system of work provides this integral approach because an effective safe system: ➤ is based on looking at the job as a whole ➤ starts from an analysis of all foreseeable hazards, e.g. physical, chemical, health; ➤ brings together all the necessary precautions, including design, physical precautions, training, monitoring, procedures and personal protective equipment. It follows from this that the use of safe systems of work is in no way a replacement for other precautions, such as good equipment design, safe construction and the use of physical safeguards. However, there are many situations where these will not give adequate protection in themselves, and then a carefully thought-out and properly implemented safe system of work is especially important. The best example is maintenance and repair work, which will often involve as a ﬁrst stage dismantling the guard or breaking through the containment, which exists for the protection of the ordinary process operator. In some of these operations, a permit to work procedure will be the most appropriate type of safe system of work.

Principles of control The operations covered may be simple or complex, routine or unusual. Whether the system is verbal or written, and whether the operation it covers is simple or complex, routine or unusual, the essential features are forethought and planning – to ensure that all foreseeable hazards are iidentiﬁed and controlled. In particular, this will involve scrutiny of: ➤ the sequence of operations to be carried out ➤ the equipment, plant, machinery and tools involved ➤ chemicals and other substances to which people might be exposed in the course of the work ➤ the people doing the work – their skill and experience ➤ foreseeable hazards (health, safety, environment), whether to the people doing the work or to others who might be affected by it ➤ practical precautions which, when adopted, will eliminate or minimize these hazards ➤ the training needs of those who will manage and operate under the procedure ➤ monitoring systems to ensure that the deﬁned precautions are implemented effectively.

6.5.2

Legal requirements

The HSW Act Section 2 requires employers to provide safe plant and systems of work. In addition, many regulations made under the Act, such as the Provision and Use of Equipment Regulations 1998, require information and instruction to be provided to employees and others. In effect, this is also a more speciﬁc requirement to provide safe systems of work. Many of these safe systems, information and instructions will need to be in writing.

6.5.3

Assessment of what safe systems of work are required

Requirement It is the responsibility of the management in each organization to ensure that its operations are assessed to determine where safe systems of work need to be developed. This assessment must, at the same time, decide the most appropriate form for the safe system, that is: ➤ is a written procedure required? ➤ should the operation only be carried out under permit to work? ➤ is an informal system sufﬁcient?

Factors to be considered It is recognized that each organization must have the freedom to devise systems that match the risk potential

of their operations and which are practicable in their situation. However, they should take account of the following factors in making their decision: ➤ types of risk involved in the operation ➤ magnitude of the risk, including consideration of the worst foreseeable loss ➤ complexity of the operation ➤ past accident and loss experience ➤ requirements and recommendations of the relevant health and safety authorities ➤ the type of documentation needed ➤ resources required to implement the safe system of work (including training and monitoring).

6.5.4

Development of safe systems

Role of competent person Primarily management is responsible to provide safe systems of work. Managers and employees know the detailed way in which the task should be carried out. The competent person appointed under the MHSW Regulations should assist managers to draw up guidelines for safe systems of work with suitable forms and should advise management on the adequacy of the safe systems produced.

Analysis The safe system of work should be based on a thorough analysis of the job or operation to be covered by the system. The way this analysis is done will depend on the nature of the job/operation. If the operation being considered is a new one involving high loss potential, the use of formal hazard analysis techniques such as HAZOP (Hazard and Operability study), FTA (Fault Tree Analysis) or Failure Modes and Effects Analysis should be considered. However, where the potential for loss is lower, a more simple approach, such as JSA (Job Safety Analysis), will be sufﬁcient. This will involve three key stages: ➤ identiﬁcation of the key steps in the job/operation – what activities will the work involve? ➤ analysis and assessment of the risks associated with each stage – what could go wrong? ➤ deﬁnition of the precautions or controls to be taken – what steps need to be taken to ensure the operation proceeds without danger, either to the people doing the work, or to anyone else? The results of this analysis are then used to draw up the safe operating procedure. (See Appendix 6.2 for a suitable form.)

87

Introduction to Health and Safety at Work Consultation Many people operating a piece of equipment or process are in the best position to help with the preparation of safe systems of work. Consultation with those employees who will be exposed to the risks, either directly or through their representatives, is also a legal requirement. The importance of discussing the proposed system with those who will have to work under it, and those who will have to supervise its operation, cannot be emphasized enough.

6.5.5

Preparation of safe systems

A checklist for use in the preparation of safe systems of work is set out as follows: ➤ what is the work to be done? ➤ what are the potential hazards? ➤ is the work covered by any existing instructions or procedures? If so, to what extent (if any) do these need to be modiﬁed? ➤ who is to do the work? ➤ what are their skills and abilities – is any special training needed? ➤ under whose control and supervision will the work be done? ➤ will any special tools, protective clothing or equipment (e.g. breathing apparatus) be needed? Are they ready and available for use? ➤ are the people who are to do the work adequately trained to use the above? ➤ what isolations and locking-off will be needed for the work to be done safely? ➤ is a permit to work required for any aspect of the work? ➤ will the work interfere with other activities? Will other activities create a hazard to the people doing the work? ➤ have other departments been informed about the work to be done, where appropriate? ➤ how will the people doing the work communicate with each other? ➤ have possible emergencies and the action to be taken been considered? ➤ should the emergency services be notiﬁed? ➤ what are the arrangements for handover of the plant/ equipment at the end of the work? (For maintenance/ project work etc.) ➤ do the planned precautions take account of all foreseeable hazards? ➤ who needs to be informed about or receive copies of the safe system of work? ➤ what arrangements will there be to see that the agreed system is followed and that it works in practice?

88

➤ what mechanism is there to ensure that the safe system of work stays relevant and up-to-date?

6.5.6

Documentation

Safe systems of work should be properly documented. Wherever possible, they should be incorporated into normal process operating procedures. This is so that: ➤ health and safety are seen as an integral part of, and not add-on to, normal production procedures ➤ the need for operators and supervisors to refer to separate manuals is minimized. Whatever method is used, all written systems of work should be signed by the relevant managers to indicate approval or authorization. Version numbers should be included so that it can quickly be veriﬁed that the most up-to-date version is in use. Records should be kept of copies of the documentation, so that all sets are amended when updates and other revisions are issued. As far as possible, systems should be written in a non-technical style and should speciﬁcally be designed to be as intelligible and user-friendly as possible. It may be necessary to produce simple summary sheets, which contain all the key points in an easy-to-read format.

6.5.7

Communication and training

People doing work or supervising work must be made fully aware of the laid-down safe systems that apply. The preparation of safe systems will often identify a training need that must be met before the system can be implemented effectively. In addition, people should receive training in how the system is to operate. This applies not only to those directly involved in doing the work but also to supervisors/managers who are to oversee it. In particular, the training might include: ➤ ➤ ➤ ➤

why a safe system is needed what is involved in the work the hazards which have been identiﬁed the precautions which have been decided and, in particular ➤ the isolations and locking-off required, and how this is to be done ➤ details of the permit to work system, if applicable ➤ any monitoring (e.g. air testing) which is to be done during the work, or before it starts ➤ how to use any necessary personal protective equipment ➤ emergency procedures.

Principles of control 6.5.8

Monitoring safe systems

Safe systems of work should be monitored to ensure that they are effective in practice. This will involve: ➤ reviewing and revising the systems themselves, to ensure they stay up-to-date ➤ inspection to identify how fully they are being implemented. In practice, these two things go together, since it is likely that a system that is out of date will not be fully implemented by the people who are intended to operate it. All organizations are responsible for ensuring that their safe systems of work are reviewed and revised as appropriate. Monitoring of implementation is part of all line managers’ normal operating responsibilities, and should also take place during health and safety audits.

6.6 Lone workers People who work by themselves without close or direct supervision are found in many work situations. In some cases they are the sole occupant of small workshops or warehouses; they may work in remote sections of a large site; they may work out of normal hours, like cleaners or security personnel; they may be working away from their main base as installers, or maintenance people; they could be people giving a service, like social workers, home helps, drivers and estate agents. There is no general legal reason why people should not work alone but there may be special risks which require two or more people to be present, for example, during entry into a conﬁned space in order to effect a rescue. It is important to ensure that a lone worker is not put at any higher risk than other workers. This is achieved by carrying out a speciﬁc risk assessment and introducing special protection arrangements for their safety. People particularly at risk, like young people or women, should also be considered. People’s overall health and suitability to work alone should be taken into account. Procedures may include: ➤ periodic visits from the supervisor to observe what is happening ➤ regular voice contact between the lone worker and the supervisor ➤ automatic warning devices to alert others if a speciﬁc signal is not received from the lone worker ➤ other devices to raise the alarm, which are activated by the absence of some speciﬁc action ➤ checks that the lone worker has returned safely home or to their base

➤ special arrangements for ﬁrst aid to deal with minor injuries, this may include mobile ﬁrst aid kits ➤ arrangements for emergencies should be established and employees trained.

6.7 Permits to work 6.7.1

Introduction

Safe systems of work are crucial in work such as the maintenance of chemical plant where the potential risks are high and the careful coordination of activities and precautions is essential to safe working. In this situation and others of similar risk potential, the safe system of work is likely to take the form of a permit to work procedure. The permit to work procedure is a specialized type of safe system of work for ensuring that potentially very dangerous work (e.g. entry into process plant and other conﬁned spaces) is done safely. Although it has been developed and reﬁned by the chemical industry, the principles of permit to work procedures are equally applicable to the management of complex risks in other industries. Its fundamental principle is that certain deﬁned operations are prohibited without the speciﬁc permission of a responsible manager, this permission being only granted once stringent checks have been made to ensure that all necessary precautions have been taken and that it is safe for work to go ahead. The people doing the work take on responsibility for following and maintaining the safeguards set out in the permit, which will deﬁne the work to be done (no other work being permitted) and the timescale in which it must be carried out. To be effective, the permit system requires the training needs of those involved to be identiﬁed and met, and monitoring procedures to ensure that the system is operating as intended.

6.7.2

Permit to work procedures

The permit to work procedure is a specialized type of safe system of work under which certain categories of high risk-potential work may only be done with the speciﬁc permission of an authorized manager. This permission (in the form of the permit to work) will only be given if the laid-down precautions are in force and have been checked. The permit document will typically specify: ➤ what work is to be done ➤ the plant/equipment involved, and how they are identiﬁed

89

Introduction to Health and Safety at Work ➤ who is authorized to do the work ➤ the steps which have already been taken to make the plant safe ➤ potential hazards which remain, or which may arise as the work proceeds ➤ the precautions to be taken against these hazards ➤ for how long the permit is valid ➤ that the equipment is released to those who are to carry out the work.

2.

3.

4. 5.

In accepting the permit, the person in charge of doing the authorized work normally undertakes to take/maintain whatever precautions are outlined in the permit. The permit will also include spaces for: ➤ signature certifying that the work is complete ➤ signature conﬁrming re-acceptance of the plant/ equipment.

6.7.3

Principles

Permit systems must adhere to the following eight principles: 1.

6.

wherever possible, and especially with routine jobs, hazards should be eliminated so that the work can be done safely without requiring a permit to work

7.

8.

although the Site Manager may delegate the responsibility for the operation of the permit system, the overall responsibility for ensuring safe operation rests with him/her the permit must be recognized as the master instruction which, until it is cancelled, overrides all other instructions the permit applies to everyone on site, including contractors information given in a permit must be detailed and accurate. It must state: (a) which plant/equipment has been made safe and the steps by which this has been achieved (b) what work may be done (c) the time at which the permit comes into effect the permit remains in force until the work has been completed and the permit is cancelled by the person who issued it, or by the person nominated by management to take over the responsibility (e.g. at the end of a shift or during absence) no work other than that speciﬁed is authorized. If it is found that the planned work has to be changed, the existing permit should be cancelled and a new one issued responsibility for the plant must be clearly deﬁned at all stages.

6.7.4

Work requiring a permit

The main types of permit and the work to be covered by each are identiﬁed below. Appendix 6.3 illustrates the essential elements of a permit form with supporting notes on its operation.

General permit The general permit should be used for work such as: ➤ alterations to or overhaul of plant or machinery where mechanical, toxic or electrical hazards may arise ➤ work on or near overhead crane tracks ➤ work on pipelines with hazardous contents ➤ repairs to railway tracks, tippers, conveyors ➤ work with asbestos-based materials ➤ work involving ionising radiation ➤ roof work ➤ excavations to avoid underground services.

Confined space permit

Figure 6.8

90

Permit to work.

Conﬁned spaces include chambers, tanks (sealed and open-top), vessels, furnaces, ducts, sewers, manholes, pits, ﬂues, excavations, boilers, reactors and ovens. Many fatal accidents have occurred where inadequate precautions were taken before and during work involving entry into conﬁned spaces. The two main hazards

Principles of control

Figure 6.9

Entering a confined space.

are the potential presence of toxic or other dangerous substances and the absence of adequate oxygen. In addition, there may be mechanical hazards (entanglement on agitators) ingress of ﬂuids, risk of engulfment in a free ﬂowing solid like grain or sugar, and raised temperatures. The work to be carried out may itself be especially hazardous when done in a conﬁned space, for example, cleaning using solvents, cutting/welding work. Should the person working in a conﬁned space get into difﬁculties for whatever reason, getting help in and getting the individual out may prove difﬁcult and dangerous. Stringent preparation, isolation, air testing and other precautions are therefore essential and experience shows that the use of a conﬁned space entry permit is essential to conﬁrm that all the appropriate precautions have been taken. The Conﬁned Spaces Regulations 1997 are summarized in Chapter 17. They detail the speciﬁc controls that are necessary when people enter conﬁned spaces.

Work on high voltage apparatus (including testing) Work on high voltage apparatus (over about 600 volts) is potentially high risk. Hazards include: ➤ possibly fatal electric shock/burns to the people doing the work ➤ electrical ﬁres/explosions ➤ consequential danger from disruption of power supply to safety-critical plant and equipment. In view of the risk, this work must only be done by suitably trained and competent people acting under the terms of a high voltage permit.

Figure 6.10 Hot work permit is usually essential except in designated areas.

Hot work Hot work is potentially hazardous as: ➤ a source of ignition in any plant in which ﬂammable materials are handled ➤ a cause of ﬁres in all processes, regardless of whether ﬂammable materials are present. Hot work includes cutting, welding, brazing, soldering and any process involving the application of a naked ﬂame. Drilling and grinding should also be included where a ﬂammable atmosphere is potentially present. Hot work should therefore be done under the terms of a hot work permit, the only exception being where hot work is done in a designated maintenance area suitable for the purpose.

6.7.5

Responsibilities

The effective operation of the permit system requires the involvement of many people. The following speciﬁc responsibilities can be identiﬁed: (Note: all appointments, deﬁnitions of work requiring a permit etc. must be in writing. All the categories of people identiﬁed below should receive training in the operation of the permit system as it affects them.)

91

Introduction to Health and Safety at Work Site manager ➤ has overall responsibility for the operation and management of the permit system ➤ appoints a senior manager (normally the chief engineer) to act as senior authorized person.

Senior authorized person ➤ is responsible to the site manager for the operation of the permit system ➤ deﬁnes the work on the site which requires a permit ➤ ensures that people responsible for this work are aware that it must only be done under the terms of a valid permit ➤ appoints all necessary authorized persons ➤ appoints a deputy to act in his/her absence.

Authorized persons ➤ issue permits to competent persons and retain copies ➤ personally inspect the site to ensure that the conditions and proposed precautions are adequate and that it is safe for the work to proceed ➤ accompany the competent person to the site to ensure that the plant/equipment is correctly identiﬁed and that the competent person understands the permit ➤ cancel the permit on satisfactory completion of the work.

Competent persons ➤ receive permits from authorized persons ➤ read the permit and make sure they fully understand the work to be done and the precautions to be taken ➤ signify their acceptance of the permit by signing both copies ➤ comply with the permit and make sure those under their supervision similarly understand and implement the required precautions ➤ on completion of the work, return the permit to the authorized person who issued it.

➤ using suitable techniques and equipment to monitor the working environment for toxic or ﬂammable materials, or for lack of oxygen ➤ giving advice to managers on safe methods of working. Specialists must not assume responsibility for the permit system. This lies with the site manager and the senior authorized person.

Engineers (and others responsible for work covered by permits) ➤ ensure that permits are raised as required.

Contractors The permit system should be applied to contractors in the same way as to direct employees. The contractor must be given adequate information and training on the permit system, the restrictions it imposes and the precautions it requires.

6.8 Emergency procedures 6.8.1

Introduction

Most of this chapter is about the principles of control to prevent accidents and ill-health. Emergency procedures, however, are about control procedures and equipment to limit the damage to people and property caused by an incident. Local ﬁre authorities will often be involved and are normally prepared to give advice to employers. Under Regulation 8 of the Management of Health and Safety at Work Regulations 1999, procedures must be established and set in motion when necessary to deal with serious and imminent danger to persons at work. Necessary links must be maintained with local authorities,

Operatives ➤ read the permit and comply with its requirements, under the supervision of the competent person.

Specialists A number of permits require the advice/skills of specialists in order to operate effectively. Such specialists may include chemists, electrical engineers, health and safety advisers and ﬁre ofﬁcers. Their role may involve: ➤ isolations within his/her discipline – e.g. electrical work

92

Figure 6.11

Emergency services at work.

Principles of control particularly with regard to ﬁrst aid, emergency medical care and rescue work. Although ﬁre is the most common emergency likely to be faced, there are many other possibilities, which should be considered including: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

gas explosion electrical burn or electrocution escape of toxic gases or fumes discovery of dangerous dusts like asbestos in the atmosphere bomb warning large vehicle crashing into the premises aircraft crash if near a ﬂight path spread of highly infectious disease severe weather with high winds and ﬂooding.

6.8.2

Fire routines and fire notices

Site managers must make sure that all employees are familiar with the means of escape in case of ﬁre and their use, and with the routine to be followed in the event of ﬁre. To achieve this, routine procedures must be set up and made known to all employees, generally outlining the action to be taken in case of ﬁre and speciﬁcally laying down the duties of certain nominated persons. Notices should be posted throughout the premises. While the need in individual premises may vary, there are a number of basic components which should be considered when designing any ﬁre routine procedures: ➤ ➤ ➤ ➤ ➤ ➤ ➤

the action to be taken on discovering a ﬁre the method of operating the ﬁre alarm the arrangements for calling the ﬁre brigade the stopping of machinery and plant ﬁrst-stage ﬁre ﬁghting by employees evacuation of the premises assembly of staff, customers and visitors and, carrying out a roll call to account for everyone on the premises.

The procedures must take account of those people who may have difﬁculty in escaping quickly from a building because of their location or a disability. Insurance companies and other responsible people may need to be consulted where special procedures are necessary to protect buildings and plant during or after people have evacuated. For example, there may be some special procedures necessary to ensure that a sprinkler system is operating in the event of ﬁre.

6.8.3

Supervisory duties

A member of the staff should be nominated to supervise all ﬁre and emergency arrangements. This person should

be in a senior position or at least have direct access to a senior manager. Senior members of the staff should be appointed as departmental ﬁre wardens, with deputies for every occasion of absence, however brief. In the event of ﬁre or other emergency, their duties would be, while it remains safe to do so, to ensure that: ➤ the alarm has been raised ➤ the whole department, including toilets and small rooms, has been evacuated ➤ the ﬁre brigade has been called ➤ ﬁre doors are closed to prevent ﬁre spread to adjoining compartments and to protect escape routes ➤ plant and machinery are shut down wherever possible and any other actions required to safeguard the premises are taken where they do not expose people to undue risks ➤ a roll call is carried out at the assembly point and the result reported to whoever is in control of the evacuation. Under normal conditions ﬁre wardens should check that good standards of housekeeping and preventive maintenance exist in their department, that exits and escape routes are kept free from obstruction, that all ﬁre-ﬁghting appliances are available for use and ﬁre points are not obstructed, that smoking is rigidly controlled, and that all members of staff under their control are familiar with the emergency procedure and know how to use the ﬁre alarm and ﬁre ﬁghting equipment.

6.8.4

Assembly and roll call

Assembly points should be established for use in the event of evacuation. It should be in a position, preferably under cover, which is unlikely to be affected at the time of ﬁre. In some cases it may be necessary to make mutual arrangements with the occupiers of nearby premises. In the case of small premises, a complete list of the names of all staff should be maintained so that a roll call can be made if evacuation becomes necessary. In those premises where the number of staff would make a single roll call difﬁcult, each departmental ﬁre warden should maintain a list of the names of staff in their area. Roll call lists must be updated regularly.

6.8.5

Fire notices

Printed instructions for the action to be taken in the event of ﬁre should be displayed throughout the premises. The information contained in the instructions should be stated brieﬂy and clearly. The staff and their deputies to whom speciﬁc duties are allocated should be identiﬁed.

93

Introduction to Health and Safety at Work Instruction for the immediate calling of the ﬁre brigade in case of ﬁre should be displayed at telephone switchboards, exchange telephone instruments and security lodges. A typical ﬁre notice is given in Appendix 6.1.

Many small ﬁrms will only need to make the minimum ﬁrst-aid provision. However, there are factors which might make greater provision necessary. The following checklist covers the points that should be considered.

6.9.2 6.8.6

The alarm system should be tested every week, while the premises are in normal use. The test should be carried out by activating a different call point each week, at a ﬁxed time. (See Chapter 13 for more information on ﬁre hazards and control.)

6.8.7

Aspects to consider

Testing

Fire drills

Once a ﬁre routine has been established it must be tested at regular intervals in order to ensure that all staff are familiar with the action to be taken in an emergency. The most effective way of achieving this is by carrying out ﬁre drills at prescribed intervals. Drills should be held at least twice a year other than in areas dealing with hazardous processes where they should be more frequent. A programme of ﬁre drills should be planned to ensure that all employees, including shift workers and part-time employees, are covered.

The risk assessments carried out under the MHSW and COSHH regulations should show whether there any speciﬁc risks in the workplace. The following should be considered: ➤ are there hazardous substances, dangerous tools and equipment; dangerous manual handling tasks, electrical shock risks, dangers from neighbours or animals? ➤ are there different levels of risk in parts of the premises or site? ➤ what is the accident and ill-health record, type and location of incidents? ➤ what is the total number of persons likely to be on site?

6.9 First aid at work 6.9.1

Introduction

People at work can suffer injuries or fall ill. It does not matter whether the injury or the illness is caused by the work they do. What is important is that they receive immediate attention and that an ambulance is called in serious cases. First aid at work covers the arrangements employers must make to ensure this happens. It can save lives and prevent minor injuries becoming major ones. The Health and Safety (First-Aid) Regulations 1981 requires employers to provide adequate and appropriate equipment, facilities and personnel to enable ﬁrst aid to be given to employees if they are injured or become ill at work. What is adequate and appropriate will depend on the circumstances in a particular workplace. The minimum ﬁrst-aid provision on any worksite is: ➤ a suitably stocked ﬁrst-aid box ➤ an appointed person to take charge of ﬁrst-aid arrangements. It is also important to remember that accidents can happen at any time. First-aid provision needs to be available at all times people are at work.

94

Figure 6.12 (a) First aid and stretcher sign: (b) first aid sign.

Principles of control ➤ are there young people, pregnant or nursing mothers on site, employees with disabilities or special health problems? ➤ are the facilities widely dispersed with several buildings or compact in a multi-storey building? ➤ what is the pattern of working hours, does it involve night work? ➤ is the site remote from emergency medical services? ➤ do employees travel a lot or work alone? ➤ do any employees work at sites occupied by other employers? ➤ are members of the public regularly on site?

6.9.3

Impact on first-aid provision if risks are significant

First aiders may need to be appointed if risks are signiﬁcant. This will involve a number of factors which must be considered, including: ➤ training for ﬁrst aiders ➤ additional ﬁrst-aid equipment and the contents of the ﬁrst-aid box ➤ siting of ﬁrst-aid equipment to meet the various demands in the premises. For example, provision of equipment in each building or on several ﬂoors. There needs to be ﬁrst-aid provision at all times during working hours ➤ informing local medical services of the site and its risks ➤ any special arrangements that may be needed with the local emergency services. If employees travel away from the site the employer needs to consider: ➤ issuing personal ﬁrst-aid kits and providing training ➤ issuing mobile phones to employees ➤ making arrangements with employers on other sites. Although there are no legal responsibilities for nonemployees, the HSE strongly recommends that they are included in any ﬁrst-aid provision.

6.9.4

Table 6.1

Contents of first aid box – low risk

Stock for up to 50 persons: A leaﬂet giving general guidance on ﬁrst aid, e.g. HSE leaﬂet Basic advice on first aid at work. • Medical adhesive plasters

40

• Sterile eye pads

4

• Individually wrapped triangular bandages

6

• Safety pins

6

• Individually wrapped: medium sterile unmedicated wound dressings

8

• Individually wrapped: large sterile unmedicated wound dressings

4

• Individually wrapped wipes

10

• Paramedic shears

1

• Pairs of latex gloves

2

• Sterile eyewash if no clean running water

2

6.9.5

Appointed persons

An appointed person is someone that is appointed by management to: ➤ take charge when someone is injured or falls ill. This includes calling an ambulance if required ➤ look after the ﬁrst-aid equipment, for example, keeping the ﬁrst-aid box replenished ➤ keeping records of treatment given. Appointed persons should never attempt to give ﬁrst aid for which they are not competent. Short emergency ﬁrstaid training courses are available. Remember that an appointed person should be available at all times when people are at work on site – this may mean appointing more than one. The training should be repeated every three years to keep up to date.

Contents of the first-aid box 6.9.6

There is no standard list of items to put in a ﬁrst-aid box. It depends on what the employer assesses the needs to be. Where there is no special risk in the workplace, a minimum stock of ﬁrst-aid items is listed in Table 6.1. Tablets or medicines should not be kept in the ﬁrst-aid box. Table 6.1 is a suggested contents list only; equivalent but different items will be considered acceptable.

A first aider

A ﬁrst aider is someone who has undergone an HSE approved training course in administering ﬁrst aid at work and holds a current ﬁrst aid at work certiﬁcate. Lists of local training organizations are available from the local environmental ofﬁcer or HSE Ofﬁces. The training should be repeated every three years to maintain a valid certiﬁcate and keep the ﬁrst aider up to date.

95

Introduction to Health and Safety at Work Table 6.2

Number of first-aid personnel

Category of risk

Numbers employed at any location

Suggested number of first-aid personnel

Fewer than 50 50–100 More than 100

At least one appointed person At least one ﬁrst aider One additional ﬁrst aider for every 100 employed

Fewer than 20 20–100 More than 100

At least one appointed person At least one ﬁrst aider for every 50 employed (or part thereof) One additional ﬁrst aider for every 100 employed

Fewer than 5 5–50 More than 50

At least one appointed person At least one ﬁrst aider One additional ﬁrst aider for every 50 employed

Lower risk e.g. shops and ofﬁces, libraries

Medium risk e.g. light engineering and assembly work, food processing, warehousing

Higher risk e.g. most construction, slaughterhouses, chemical manufacture, extensive work with dangerous machinery or sharp instruments Source HSE

It is not possible to give hard and fast rules on when or how many ﬁrst aiders or appointed persons might be needed. This will depend on the circumstances of each particular organization or worksite. Table 6.2 offers suggestions on how many ﬁrst aiders or appointed persons might be needed in relation to categories of risk and number of employees. The details in the table are suggestions only, they are not deﬁnitive, nor are they a legal requirement. Employees must be informed of the first-aid arrangements. Putting up notices telling staff who and where the ﬁrst aiders or appointed persons are and where the ﬁrst-aid box is will usually be enough. Special arrangements will be needed for employees with reading or language difﬁculties.

6.9.7

Suggested numbers of first-aid personnel

To ensure cover at all times when people are at work and where there are special circumstances, such as remoteness from emergency medical services, shiftwork, or sites with several separate buildings, there may need to be more ﬁrst-aid personnel than set out in Table 6.2.

6.9.8 Provision must be sufficient to cover for absences. In June 2006 the HSE indicated that upon their review of the First Aid Regulations they decided to retain approval of the training courses within the HSE but make changes to the structure of the course. The intention is that in

96

future, employers will be able to send suitable employees on either a 6 hour (minimum) emergency ﬁrst aid at work (EFAW) or an 18 hour (minimum) FAW course, based on the ﬁndings of their ﬁrst aid needs assessment (see Fig. 6.13). After 3 years, ﬁrst aiders will need to complete another course (either a 6 hour EFAW or 12 hour FAW requaliﬁcation course, as appropriate) to obtain a new certiﬁcate. Within any 3 year certiﬁcation period, ﬁrst aiders should complete two annual refresher courses, covering basic life support/skills updates, that will each last for at least 3 hours. No date for the introduction of these courses has been set but HSE is aware that FAW training providers require an adequate lead-in period. There are a number of additional issues to be clariﬁed before a date can be ﬁnalized. Firstly, whether the 3 day FAW course needs to be trialed in a pilot study prior to its introduction. Secondly, consideration will be given to any arrangements that need to be put in place for the approval and monitoring of those providers wishing to offer the EFAW course and whether these arrangements should be extended to those offering annual refresher training. HSE will revise the guidance for employers in its publication: First Aid at Work: The Health and Safety (First-Aid) Regulations 1981 Approved Code of Practice and Guidance (L74). This will help employers understand the new training regime and will provide more detailed information on how to conduct a ﬁrst aid needs assessment. HSE recognizes this is crucial in ensuring employers send

Principles of control

First aid needs assessment

Year 0

Emergency first aid at work (EFAW) (6 Hours) Certificate valid for 3 years

First aid at work (FAW) (18 Hours) Certificate valid for 3 years

Year 1

Basic skills update (3 Hours)

Year 2

Basic skills update (3 Hours)

Year 3

EFAW (6 Hours – same course as year 0) Certificate valid for 3 years

FAW requalification (12 Hours) Certificate valid for 3 years

Figure 6.13 Flow chart showing courses to be completed over a 3 year certification period for emergency first aid at work and first aid at work. The dotted line indicates the route to be taken in subsequent years after completion of the relevant course at year 3.

prospective ﬁrst aiders on the course that most closely meets the needs of their workplace. The guidance will also strongly emphasize that HSE will consider it good practice for ﬁrst aiders to undertake annual refresher training. Once the guidance has been drafted, it will be subject to a consultation process with stakeholders, as appropriate. Summary of the HSE’s review is that: ➤ HSE recognizes the FWC as the lead industry body with representation from all sectors f the FAW training provider industry ➤ HSE will not transfer FAAMS to the FWC and will retain it in-house ➤ HSE has made some modiﬁcations to the structure of FAW training courses since its Position Statement was published ➤ HSE needs to resolve a number of issues before a date for the introduction of the new courses is announced and an adequate lead-in period will be given for FAW training providers.

Any further signiﬁcant development will be published on the ﬁrst aid web pages of HSE’s website.

6.10 Practice NEBOSH questions for Chapter 6 1. With respect to the management of risk within the workplace: (i) explain the meaning of the term ‘hierarchy of control’ (ii) outline, with example, the standard hierarchy that should be applied with respect to controlling health and safety risks in the workplace. 2. Outline the possible effects on health and safety of poor standards of housekeeping in the workplace. 3. Name and describe FOUR classes of safety sign prescribed by the Health and Safety (Safety Signs and Signals) Regulations 1996.

97

Introduction to Health and Safety at Work 4. State the shape and colour, and give a relevant example, of each of the following types of safety sign: (i) prohibition (ii) warning (iii) mandatory (iv) emergency escape or ﬁrst-aid. 5. Explain why personal protective equipment (PPE) should be considered as a last resort in the control of occupational health hazards. 6. (a) Explain the meaning of the term ‘safe system of work’ (b) Describe the enforcement action that could be taken by an enforcing authority when a safe system of work has not been implemented. 7. Outline the factors that should be considered when developing a safe system of work. 8. Identify EIGHT sources of information that might usefully be consulted when developing a safe system of work. 9. Outline the reasons why employees may fail to comply with safety procedures at work. 10. Due to an increase in knife related accidents amongst hotel kitchen staff who use the sharp tools in the preparation of food for the restaurant, a safe system of work is to be developed to minimize the risk of injury to this group of employees. (i) Identify the legal requirements, under which the employer must provide a safe system of work (ii) Describe the issues to be addressed when developing the safe system of work for the hotel kitchen staff who use the knives as part of their work (iii) Outline the ways in which the employer could motivate the hotel kitchen staff to follow the safe system of work. 11. (a) Define term ‘permit-to-work system’ (b) Outline THREE types of work situations that may require a permit-to-work system, giving reasons in EACH case for the requirement (c) Outline the speciﬁc details that should be included in a permit-to-work for entry into a conﬁned space.

98

12. (a) Identify TWO speciﬁc work activities for which a permit-to-work system might be needed (b) Outline the key elements of a permit-to-work system. 13. Outline the issues to be addressed in a training session on the operation of a permit-to-work system. 14. With reference to the Conﬁned Space Regulations 1997: (i) define the meaning of ‘conﬁned space’, giving TWO workplace examples (ii) outline speciﬁc hazards associated with working in conﬁned spaces (iii) identify FOUR ‘speciﬁed risks’ that may arise from work in a conﬁned space. 15. Outline the precautions that should be taken in order to ensure the safety of employees undertaking maintenance work in an underground storage vessel. 16. Outline the factors that should be considered when preparing a procedure to deal with a workplace emergency. 17. (a) Identify FOUR types of emergency procedure that an organization might need to have in place (b) Explain why visitors to workplace should be informed of the emergency procedures. 18. (a) Identify THREE types of emergencies in the workplace for which employees may need to be evacuated (b) Explain why it is important to develop workplace procedures to enable the safe evacuation of employees during an emergency. 19. (a) Identify the TWO main functions of ﬁrst-aid treatment (b) Outline the factors to consider when making an assessment of ﬁrst-aid provision in a workplace. 20. Outline the factors to consider when making an assessment of ﬁrst-aid provision in a workplace.

Principles of control Appendix 6.1

Fire notice

99

Introduction to Health and Safety at Work Appendix 6.2

Job safety analysis form

JOB SAFETY ANALYSIS Job

Date

Department

Carried out by

Description of job Legal requirements and guidance Task steps

Safe system of work

Job Instruction

Training requirements

Review date

100

Hazards

Consequence

Severity

Risk C S

Controls

Principles of control Appendix 6.3

Essential elements of a permit-to-work form

2. Should have any reference to other relevant permits or isolation certiﬁcates.

1 Permit Title

2 Permit Number

3 Job Title 4 Plant identiﬁcation 5. Description of work to be done and its limitations.

5 Description of Work

6. Hazard identiﬁcation including residual hazards and hazards introduced by the work.

6 Hazard Identiﬁcation

7. Precautions necessary – person(s) who carry out precautions, e.g. isolations, should sign that precautions have been taken.

7 Precautions necessary

.......................................... .......................................... .......................................... 8. Protective equipment needed for the task.

8 Protective Equipment

9. Authorization signature conﬁrming that isolations have been made and precautions taken, except where these can only be taken during the work. Date and time duration of permit.

9 Authorization

10. Acceptance signature conﬁrming understanding of work to be done, hazards involved and precautions required. Also conﬁrming permit information has been explained to all workers involved.

10 Acceptance

11. Extension/Shift handover signature conﬁrming checks have been made that plant remains safe to be worked on, and new acceptance/workers made fully aware of hazards/precautions. New time expiry given.

11 Extension/Shift handover

12. Hand back signed by acceptor certifying work completed. Signed by issuer certifying work completed and plant ready for testing and re-commissioning.

12 Hand back

13. Cancellation certifying work tested and plant satisfactorily re-commissioned.

13 Cancellation

7 Signatures

.................................... .................................... ....................................

Source HSE

101

7

Monitoring, review and audit

7.1 Introduction This chapter concerns the monitoring of health and safety performance, including both positive measures like inspections and negative measures like injury statistics. It is about reviewing progress to see if something better can be done and auditing to ensure that what has been planned is being implemented. Measurement is a key step in any management process and forms the basis of continuous improvement. If measurement is not carried out correctly, the effectiveness of the health and safety management system is undermined and there is no reliable information to show managers how well the health and safety risks are controlled. Managers should ask key questions to ensure that arrangements for health and safety risk control are in place, comply with the law as a minimum, and operate effectively. Proactive monitoring, by taking the initiative before things go wrong, involves routine inspections and checks to make sure that standards and policies are being implemented and that controls are working. Reactive monitoring, after things go wrong, involves looking at historical events to learn from mistakes and see what can be put right to prevent a recurrence. The UK HSE’s experience is that organizations ﬁnd health and safety performance measurement a difﬁcult subject. They struggle to develop health and safety performance measures which are not based solely on injury and ill-health statistics.

102

7.2 The traditional approach to measuring health and safety performance Senior managers often measure company performance by using, for example, percentage proﬁt, return on investment or market share. A common feature of the measures would be that they are generally positive in nature – which demonstrates achievement – rather than negative, which demonstrates failure. Yet, if senior managers are asked how they measure their companies’ health and safety performance, it is likely that the only measure would be accident or injury statistics. While the general business performance of an organization is subject to a range of positive measures, for health and safety it too often comes down to one negative measure, injury and ill-health statistics – measures of failures. Health and safety differs from many areas measured by managers because improvement in performance means fewer outcomes from the measure (injuries or ill-health) rather than more. A low injury or ill-health rate trend over years is still no guarantee that risks are being controlled and that incidents will not happen in the future. This is particularly true in organizations where major hazards are present but there is a low probability of accidents. There is no single reliable measure of health and safety performance. What is required is a ‘basket’ of measures, providing information on a range of health and safety issues.

Monitoring, review and audit There are some signiﬁcant problems with the use of injury/ill-health statistics in isolation: ➤ there may be under-reporting – focusing on injury and ill-health rates as a measure, especially if a reward system is involved, can lead to non-reporting to keep up performance ➤ it is often a matter of chance whether a particular incident causes an injury, and they may not show whether or not a hazard is under control. Luck or a reduction in the number of people exposed, may produce a low injury/accident rate rather than good health and safety management ➤ an injury is the particular consequence of an incident and often does not reﬂect the potential severity. For example, an unguarded machine could result in a cut ﬁnger or an amputation ➤ people can be absent from work for reasons which are not related to the severity of the incident ➤ there is evidence to show that there is little relationship between ‘occupational’ injury statistics (e.g. slips, trip and falls) and the reasons for the lack of control of major accident hazards (e.g. loss of containment of ﬂammable or toxic material) ➤ a small number of accidents may lead to complacency ➤ injury statistics demonstrate outcomes not causes. Because of the potential shortcomings related to the use of accident/injury and ill-health data as a single measure of performance, more proactive or ‘up stream’ measures are required. These require a systematic approach to deriving positive measures and how they link to the overall risk control process, rather than a quick-ﬁx based on things that can easily be counted, such as the numbers of training courses or numbers of inspections, which has limited value. The resultant data provide no information on how the ﬁgure was arrived at, whether it is ‘acceptable’ (i.e. good/bad) or the quality and effectiveness of the activity. A more disciplined approach to health and safety performance measurement is required. This needs to develop as the health and safety management system develops.

7.3 Why measure performance? 7.3.1

Introduction You can’t manage what you can’t measure – Drucker

Measurement is an accepted part of the ‘plan-do-checkact’ management process. Measuring performance is as

Policy

Organizing

Auditing

Planning and implementing

Measuring performance

Reviewing performance

Figure 7.1

The health and safety management system.

much part of a health and safety management system as ﬁnancial, production or service delivery management. The HSG 65 framework for managing health and safety, discussed at the end of Chapter 1 and illustrated in Figure 7.1, shows where measuring performance ﬁts within the overall health and safety management system. The main purpose of measuring health and safety performance is to provide information on the progress and current status of the strategies, processes and activities employed to control health and safety risks. Effective measurement not only provides information on what the levels are but also why they are at this level, so that corrective action can be taken.

7.3.2

Answering questions

Health and safety monitoring or performance measurement should seek to answer such questions as: ➤ where is the position relative to the overall health and safety aims and objectives? ➤ where is the position relative to the control of hazards and risks? ➤ how does the organization compare with others? ➤ what is the reason for the current position? ➤ is the organization getting better or worse over time? ➤ is the management of health and safety doing the right things? ➤ is the management of health and safety doing things right consistently? ➤ is the management of health and safety proportionate to the hazards and risks?

103

Introduction to Health and Safety at Work ➤ is the management of health and safety efﬁcient? ➤ is an effective health and safety management system in place across all parts of the organization? ➤ is the culture supportive of health and safety, particularly in the face of competing demands?

there is an increasing need to demonstrate to external stakeholders (regulators, insurance companies, shareholders, suppliers, contractors, members of the public, etc.) that arrangements to control health and safety risks are in place, operating correctly and effectively.

These questions should be asked at all management levels throughout the organization. The aim of monitoring should be to provide a complete picture of an organization’s health and safety performance.

7.4 What to measure 7.4.1

7.3.3

Decision making

The measurement information helps in deciding: ➤ where the organization is in relation to where it wants to be ➤ what progress is necessary and reasonable in the circumstances ➤ how that progress might be achieved against particular restraints (e.g. resources or time) ➤ priorities – what should be done ﬁrst and what is most important ➤ effective use of resources.

7.3.4

Addressing different information needs

Information from the performance measurement is needed by a variety of people. These will include directors, senior managers, line managers, supervisors, health and safety professionals and employees/safety representatives. They each need information appropriate to their position and responsibilities within the health and safety management system. For example, what the chief executive ofﬁcer of a large organization needs to know from the performance measurement system will differ in detail and nature from the information needs of the manager of a particular location. A coordinated approach is required so that individual measuring activities ﬁt within the general performance measurement framework. Although the primary focus for performance measurement is to meet the internal needs of an organization,

INPUT Uncontrolled hazards The ‘Hazards Burden’

Figure 7.2

104

Introduction

In order to achieve an outcome of no injuries or workrelated ill-health, and to satisfy stakeholders, health and safety risks need to be controlled. Effective risk control is founded on an effective health and safety management system. This is illustrated in Figure 7.2.

7.4.2

Effective risk control

The health and safety management system comprises three levels of control (see Figure 7.2): ➤ level 3 – effective workplace precautions provided and maintained to prevent harm to people who are exposed to the risks ➤ level 2 – risk control systems (RCSs): the basis for ensuring that adequate workplace precautions are provided and maintained ➤ level 1 – the key elements of the health and safety management system: the management arrangements (including plans and objectives) necessary to organize, plan, control and monitor the design and implementation of RCSs. The health and safety culture must be positive to support each level. Performance measurement should cover all elements of Figure 7.2 and be based on a balanced approach which combines: ➤ input: monitoring the scale, nature and distribution of hazards created by the organization’s activities – measures of the hazard burden

PROCESS

OUTPUT

OUTCOME

Health and safety management systems Management arrangements (Level 1) Risk control systems (Level 2) Workplace precautions (Level 3) Positive health and safety culture

Controlled hazards/risks

1. No injuries 2. No occupational ill-health 3. No incidents 4. Stakeholder satisfaction

Health and safety management system.

Monitoring, review and audit ➤ process: active monitoring of the adequacy, development, implementation and deployment of the health and safety management system and the activities to promote a positive health and safety culture – measures of success ➤ outcomes: reactive monitoring of adverse outcomes resulting in injuries, ill-health, loss and accidents with the potential to cause injuries, ill-health or loss – measures of failure.

These information sources can be used independently or in combination. Direct observation includes inspection activities and the monitoring of the work environment (e.g. temperature, dust levels, solvent levels, noise levels) and people’s behaviour. Each risk control system should have a built-in monitoring element that will deﬁne the frequency of monitoring; these can be combined to form a common inspection system.

7.6.2

7.5 Measuring failure – reactive monitoring So far, this chapter has concentrated on measuring activities designed to prevent the occurrence of injuries and work-related ill-health (active monitoring). Failures in risk control also need to be measured (reactive monitoring), to provide opportunities to check performance, learn from failures and improve the health and safety management system. Reactive monitoring arrangements include systems to identify and report: ➤ injuries and work-related ill-health (details of the incident rate calculation is given in Chapter 4) ➤ other losses such as damage to property ➤ incidents, including those with the potential to cause injury, ill-health or loss (near misses) ➤ hazards and faults ➤ weaknesses or omissions in performance standards and systems, including complaints from employees and enforcement action by the authorities. Guidance on investigating and analysing these incidents is given in Chapter 8.

7.6 Active monitoring – how to measure performance 7.6.1

Introduction

The measurement process can gather information through: ➤ direct observation of conditions and of people’s behaviour (sometimes referred to as unsafe acts and unsafe conditions monitoring) ➤ talking to people to elicit facts and their experiences as well as gauging their views and opinions ➤ examining written reports, documents and records.

Inspections

General This may be achieved by developing a checklist or inspection form that covers the key issues to be monitored in a particular department or area of the organization within a particular period. It might be useful to structure this checklist using the ‘four Ps’ (note that the examples are not a deﬁnitive list): ➤ premises, including: ➤ access/escape ➤ housekeeping ➤ services like gas and electricity ➤ working environment ➤ ﬁre precautions ➤ plant and substances, including: ➤ machinery guarding ➤ tools and equipment ➤ local exhaust ventilation ➤ use/storage/separation of materials/chemicals ➤ procedures, including: ➤ safe systems of work ➤ permits to work ➤ use of personal protective equipment ➤ procedures followed ➤ people, including: ➤ health surveillance ➤ people’s behaviour ➤ training and supervision ➤ appropriate authorized person. It is essential that people carrying out an inspection do not in any way put themselves or anyone else at risk. Particular care must be taken with regard to safe access. In carrying out these safety inspections, the safety of people’s actions should be considered, in addition to the safety of the conditions they are working in – a ladder might be in perfect condition but it has to be used properly too.

Key points in becoming a good observer To improve health and safety performance, managers and supervisors must eliminate unsafe acts by observing them, taking immediate corrective action, and following

105

Introduction to Health and Safety at Work ➤ use all senses: sight, hearing, smell, touch ➤ maintain a balanced approach. Observe all phases of the job ➤ be inquisitive ➤ observe for ideas – not just to determine problems ➤ recognize good performance.

Daily/weekly/monthly safety inspections These will be aimed at checking conditions in a speciﬁed area against a ﬁxed checklist drawn up by local management. It will cover speciﬁc items, such as the guards at particular machines, whether access/agreed routes are clear, whether ﬁre extinguishers are in place, etc. The checks should be carried out by staff of the department who should sign off the checklist. It should not last more than half an hour, perhaps less. This is not a speciﬁc hazard spotting operation, but there should be a space on the checklist for the inspectors to note down any particular problems encountered.

(a)

Reports from inspections

(b)

Figure 7.3 (a) Poor conditions – inspection needed; (b) inspection in progress. up to prevent recurrence. To become a good observer, they must improve their observation skills and must learn how to observe effectively. Effective observation includes the following key points: ➤ ➤ ➤ ➤ ➤ ➤ ➤

be selective know what to look for practice keep an open mind guard against habit and familiarity do not be satisﬁed with general impressions record observations systematically.

Observation techniques In addition, to become a good observer, a person must: ➤ stop for 10 to 30 seconds before entering a new area to ascertain where employees are working ➤ be alert for unsafe practices that are corrected as soon as you enter an area ➤ observe activity – do not avoid the action ➤ remember ABBI – look Above, Below, Behind, Inside ➤ develop a questioning attitude to determine what injuries might occur if the unexpected happened and how the job might be accomplished more safely. Ask ‘why?’ and ‘what could happen if …?’

106

Some of the items arising from safety inspections will have been dealt with immediately, other items will require action by speciﬁed people. Where there is some doubt about the problem, and what exactly is required, advice should be sought from the site safety adviser or external expert. A brief report of the inspection and any resulting action list should be submitted to the safety committee. While the committee may not have the time available to consider all reports in detail, it will want to be satisﬁed that appropriate action is taken to resolve all matters; it will be necessary for the committee to follow up the reports until all matters are resolved.

Inspection standards In order to get maximum value from inspection checklists, they should be designed so that they require objective rather than subjective judgements of conditions. For example, asking the people undertaking a general inspection of the workplace to rate housekeeping as good or bad, begs questions as to what does good and bad mean, and what criteria should be used to judge this. If good housekeeping means there is no rubbish left on the ﬂoor; all waste bins are regularly emptied and not overﬂowing; ﬂoors are swept each day and cleaned once a week; decorations should be in good condition with no peeling paint, then this should be stated. Adequate expected standards should be provided in separate notes so that those inspecting know the standards that are required. The checklist or inspection form should facilitate: ➤ the planning and initiation of remedial action, by requiring those doing the inspection to rank deﬁciencies

Monitoring, review and audit in priority order (those actions which are most important rather than those which can be easily done quickly) ➤ identifying those responsible for taking remedial actions, with sensible timescales to track progress on implementation ➤ periodic monitoring to identify common themes which might reveal underlying problems in the system ➤ management information on the frequency or nature of the monitoring arrangements. Appendix 7.1 gives examples of poor workplaces which can be used for practice exercises. Appendix 7.2 shows a basic list of inspection issues, which can be adapted to any particular organization’s needs. A policy checklist is given in Chapter 2.

7.6.3

Safety sampling

Safety sampling is a helpful technique that helps organizations to concentrate on one particular area or subject at a time. A speciﬁc area is chosen which can be inspected in about thirty minutes. A checklist is drawn up to facilitate the inspection looking at speciﬁc issues. These may be different types of hazard; they may be unsafe acts or conditions noted; they may be pro-active, good behaviour or practices noted. The inspection team or person then carries out the sampling at the same time each day or week in the speciﬁed period. The results are recorded and analysed to see if the changes are good or bad over time. Of course, defects noted must be brought to the notice of the appropriate person for action on each occasion.

7.7 Who should monitor performance? Performance should be measured at each management level from directors downwards. It is not sufﬁcient to monitor by exception, where unless problems are raised, it is assumed to be satisfactory. Senior managers must satisfy themselves that the correct arrangements are in place and working properly. Responsibilities for both active and reactive monitoring must be laid down and managers need to be personally involved in making sure that plans and objectives are met and compliance with standards is achieved. Although systems may be set up with the guidance of safety professionals, managers should be personally involved and given sufﬁcient training to be competent to make informed judgements about monitoring performance. Other people like safety representatives will also have the right to inspect the workplace. Each employee

should be encouraged to inspect their own workplace frequently to check for obvious problems and rectify them if possible or report hazards to their supervisors. Speciﬁc statutory (or thorough) examinations of, for example, lifting equipment or pressure vessels, have to be carried out at intervals laid down in written schemes by competent persons – usually specially trained and experienced inspection/insurance company personnel.

7.8 Frequency of monitoring and inspections This will depend on the level of risk and any statutory inspection requirement. Directors may be expected to examine the premises formally at an annual audit, while departmental supervisors may be expected to carry out inspection each week. Senior managers should regularly monitor the health and safety plan to ensure that objectives are being met and to make any changes to the plan as necessary. Data from reactive monitoring should be considered by senior managers at least once a month. In most organizations serious events would be closely monitored as they happen.

7.9 Report writing There are three main aims to the writing of reports and they are all about communication. A report should aim to: ➤ get a message through to the reader ➤ make the message and the arguments clear and easy to understand ➤ make the arguments and conclusions persuasive. Communication starts with trying to get into the mind of the reader, imagining what would most effectively catch the attention, what would be most likely to convince, what will make this report stand out among others. A vital part of this is presentation; so while a handwritten report is better than nothing if time is short, a well organized, typed report is very much clearer. To the reader of the report, who may well be very busy with a great deal of written information to wade through, a clear, well presented report will produce a positive attitude from the outset, with instant beneﬁt to the writer. Five factors which help to make reports effective: ➤ ➤ ➤ ➤ ➤

structure presentation of arguments style presentation of data how the report itself is presented.

107

Introduction to Health and Safety at Work 7.9.1

Structure

Introduction The introduction should contain the following:

The structure of a report is the key to its professionalism. Good structuring will: ➤ Help the reader to understand the information and follow the arguments contained in the report ➤ Increase the writer’s credibility ➤ Ensure that the material contained in the report is organized to the best advantage. The following list shows a frequently used method of producing a report, but always bear in mind that different organizations use different formats. It is important to check with the organization requesting the report in case their in-house format differs. 1. 2. 3. 4. 5. 6. 7. 8. 9.

Title page Summary Contents list Introduction Main body of the report Conclusions Recommendations Appendices References.

Title page This will contain: ➤ a title and often a subtitle ➤ the name of the person or organization to whom the report is addressed ➤ the name of the writer(s) and their organization ➤ the date on which the report was submitted. As report writing is about communication, it is a good idea to choose a title that is eye-catching and memorable as well as being informative.

Summary Limit the summary to between 150 and 500 words. Do not include any evidence or data. This should be kept for the main report. Include the main conclusions and principal recommendations and place it near the front of the report.

Contents list Put the contents list near the beginning of the report. Short reports do not need a list but if there are several headings it does help the reader to grasp the overall content of the report in a short time.

108

➤ information about who commissioned the report and when ➤ the purpose of the report ➤ objectives of the report ➤ terms of reference ➤ preparation of the report (type of data, research undertaken, subjects interviewed, etc.) ➤ methodology used in any analysis ➤ problems and the methods used to tackle them ➤ details about consultation with clients, employees, etc. There may be other items that are speciﬁc to the report.

The main body of the report This part of the report should describe, in detail, what was discovered (the facts), the signiﬁcance of these discoveries (analysis) and their importance (evaluation). Graphs, tables and charts are often used at this stage in the report. These should have the function of summarizing information rather than giving large amounts of detail. The more detailed graphics should be made into appendices. To make it more digestible, this part of the report should be divided into sections, using numbered headings and sub-headings. Very long and complex reports will need to be broken down into chapters.

Conclusions The concluding part of the report should be a reasonably detailed ‘summing up’. It should give the conclusions arrived at by the writer and explain why the writer has reached these conclusions.

Recommendations The use of this section depends on the requirements of the person commissioning the report. If recommendations are required, provide as few as possible, to retain a clear focus. Report writers are often asked only to provide the facts.

Appendices This part of the report should contain sections that may be useful to a reader who requires more detail. Examples would be the detailed charts, graphs and tables mentioned in section 5, any questionnaires used in constructing the evidence, lists, forms, case studies and so on. The appendices are the background material of the report.

Monitoring, review and audit References If any books, papers or journal articles have been used as source material, this should be acknowledged in a reference section. There are a number of accepted referencing methods used by academics. Because the reader is likely to be a person with some degree of expertise in the subject, a report must be reliable, credible, relevant and thorough. It is therefore important to avoid emotional language, opinions presented as facts and arguments that have no supporting evidence. To make a report more persuasive, the writer needs to: ➤ ➤ ➤ ➤

present the information clearly provide reliable evidence present arguments logically avoid falsifying, tampering with or concealing facts.

Expertise in an area of knowledge means that distortions, errors and omissions will quickly be spotted by the reader and the presence of any of these will cast doubt on the credibility of the whole report. Reports are usually used as part of a decision making process. If this is the case, clear, unembellished facts are needed. Exceptions to this would be where the report is a proposal document or where a recommendation is speciﬁcally requested. Unless this is the case, it is better not to make recommendations. A report should play a key role in organizing information for the use of decision makers. It should review a complex and/or extensive body of information and make a summary of all the important issues. It is relatively straightforward to produce a report, as long as the writer keeps to a clear format. Using the format described here, it should be possible to tell the reader as clearly as possible: ➤ what happened ➤ what it cost ➤ what the result was, etc. There may be a request for a special report and this is likely to be longer and more difﬁcult to produce. Often it will relate to a ‘critical incident’ and the decision makers will be looking for information to help them: ➤ decide whether this is a problem or an opportunity ➤ decide whether to take action ➤ decide what action, if any, to take. Finally, report writing should be kept simple. Nothing is gained, in fact much is lost in the use of long, complicated sentences, jargon and ofﬁcial-sounding language. When the report is ﬁnished, it is helpful to run through it with the express intention of simplifying the language

and making sure that it says what was intended in a clear and straightforward way.

KEEP IT SHORT AND SIMPLE

7.10 Review and audit 7.10.1

Audits – purpose

The ﬁnal steps in the health and safety management control cycle are auditing and performance review. Organizations need to be able to reinforce, maintain and develop the ability to reduce risks. The ‘feedback loop’ produced by this ﬁnal stage in the process enables them to do this and to ensure continuing effectiveness of the health and safety management system. Audit is a business discipline which is frequently used, for example, in ﬁnance, environmental matters and quality. It can equally well be applied to health and safety. The term is often used to mean inspection or other monitoring activity. Here, the following deﬁnition is used, which follows HSG 65: The structured process of collecting independent information on the efficiency, effectiveness and reliability of the total health and safety management system and drawing up plans for corrective action. Over time, it is inevitable that control systems will decay and may even become obsolete as things change. Auditing is a way of supporting monitoring by providing managers with information. It will show how effectively plans and the components of health and safety management systems are being implemented. In addition, it will provide a check on the adequacy and effectiveness of the management arrangements and risk control systems (RCSs). Auditing is critical to a health and safety management system, but it is not a substitute for other essential parts of the system. Companies need systems in place to manage cash ﬂow and pay the bills – this cannot be managed through an annual audit. In the same way, health and safety needs to be managed on a day-to-day basis and for this organizations need to have systems in place. A periodic audit will not achieve this. The aims of auditing should be to establish that the three major components of a safety management system are in place and operating effectively. It should show that: ➤ appropriate place

management

arrangements

are

109

in

Introduction to Health and Safety at Work ➤ adequate risk control systems exist, are implemented, and consistent with the hazard proﬁle of the organization ➤ appropriate workplace precautions are in place. Where the organization is spread over a number of sites, the management arrangements linking the centre with the business units and sites should be covered by the audit. There are a number of ways in which this can be achieved and some parts of the system do not need auditing as often as others. For example, an audit to verify the implementation of risk control systems would be made more frequently than a more overall audit of the capability of the organization or of the management arrangements for health and safety. Critical risk control systems, which control the principal hazards of the business, would need to be audited more frequently. Where there are complex workplace precautions, it may be necessary to undertake technical audits. An example would be chemical process plant integrity and control systems. A well-structured auditing programme will give a comprehensive picture of the effectiveness of the health and safety management system in controlling risks. Such a programme will indicate when and how each component part will be audited. Managers, safety representatives and employees, working as a team, will effectively widen involvement and cooperation needed to put together the programme and implement it. The process of auditing involves: ➤ gathering information from all levels of an organization about the health and safety management system ➤ making informed judgements about its adequacy and performance.

7.10.2

Gathering information

Decisions will need to be made about the level and detail of the audit before starting to gather information about the health and safety management of an organization. Auditing involves sampling, so initially it is necessary to decide how much sampling is needed for the assessment to be reliable. The type of audit and its complexity will relate to its objectives and scope, to the size and complexity of the organization and to the length of time that the existing health and safety management system has been in operation. Information sources of interviewing people, looking at documents and checking physical conditions are usually approached in the following order:

Preparatory work ➤ meet with relevant managers and employee representatives to discuss and agree the objectives and scope of the audit

110

➤ gather and consider documentation ➤ prepare and agree the audit procedure with managers.

On-site ➤ interviewing ➤ review and assessment of additional documents ➤ observation of physical conditions and work activities.

Conclusion ➤ assemble the evidence ➤ evaluate the evidence ➤ write an audit report.

7.10.3

Making judgements

It is essential to start with a relevant standard or benchmark against which the adequacy of a health and safety management system can be judged. If standards are not clear, assessment cannot be reliable. Audit judgements should be informed by legal standards, HSE guidance and applicable industry standards. HSG 65 sets out benchmarks for management arrangements and for the design of risk control systems. This book follows the same concepts. Auditing should not be seen as a fault-ﬁnding activity. It should make a valuable contribution to the health and safety management system and to learning. It should recognize achievement as well as highlight areas where more needs to be done. Scoring systems can be used in auditing along with judgements and recommendations. This can be seen as a useful way to compare sites or monitor progress over time. However, there is no evidence that quantiﬁed results produce a more effective response than the use of qualitative evidence. Indeed, the introduction of a scoring system can, the HSE believes, have a negative effect as it may encourage managers to place more emphasis on high scoring questions which may not be as relevant to the development of an effective health and safety management system. To achieve the best results, auditors should be competent people who are independent of the area and of the activities being audited. External consultants can be used or staff from other areas of the organization. An organization can use its own auditing system or one of the proprietary systems on the market or, since it is unlikely that any ready made system will provide a perfect ﬁt, a combination of both. With any scheme, cost and beneﬁts have to be taken into account. Common problems include: ➤ systems which are too general in their approach. These may need considerable work to make them ﬁt the needs and risks of the organization

Monitoring, review and audit ➤ systems which are too cumbersome for the size and culture of the organization ➤ scoring systems may conceal problems in underlying detail ➤ organizations may design their management system to gain maximum points rather than using one which suits the needs and hazard proﬁle of the business. HSE encourages organizations to assess their health and safety management systems using in-house or proprietary schemes but without endorsing any particular one.

7.10.4

Performance review

When performance is reviewed, judgements are made about its adequacy and decisions are taken about how and when to rectify problems. The feedback loop is needed by organizations so that they can see whether the health and safety management system is working as intended. The information for review of performance comes from audits of risk control systems and workplace precautions, and from the measurement of activities. There may be other inﬂuences, both internal and external, such as re-organization, new legislation or changes in current good practice. These may result in the necessity to redesign or change parts of the health and safety management system or to alter its direction or objectives. Performance standards need to be established which will identify the systems requiring change, responsibilities, and completion dates. It is essential to feed back the information about success and failure so that employees are motivated to maintain and improve performance. In a review, the following areas will need to be examined: ➤ the operation and maintenance of the existing system ➤ how the safety management system is designed, developed and installed to accommodate changing circumstances. Reviewing is a continuous process. It should be undertaken at different levels within the organization. Responses will be needed as follows: ➤ by ﬁrst-line supervisors or other managers to remedy failures to implement workplace precautions which they observe in the course of routine activities ➤ to remedy sub-standard performance identiﬁed by active and reactive monitoring ➤ to the assessment of plans at individual, departmental, site, group or organizational level ➤ to the results of audits. The frequency of review at each level should be decided upon by the organization and reviewing activities should

be devised which will suit the measuring and auditing activities. The review will identify speciﬁc remedial actions which establish who is responsible for implementation and set deadlines for completion.

7.11 Practice NEBOSH questions for Chapter 7 1. Outline ways in which an organization can monitor its health and safety performance. 2. Identify EIGHT measures that could be used by an organization in order to monitor its health and safety performance. 3. Outline TWO reactive measures and TWO proactive (or active) measures that can be used in monitoring an organization’s health and safety performance. 4. Outline FOUR proactive (or active) monitoring methods that can be used in assessing the health and safety performance of an organization. 5. Identify FOUR active (or proactive) and FOUR reactive means by which an organization can monitor its health and safety performance. 6. An employer intends to implement a programme of regular workplace inspections following a workplace accident. (i) Outline the factors that should be considered when planning such inspections (ii) Outline THREE additional proactive (active) methods that could be used in the monitoring of health and safety performance (iii) Identify the possible costs to the organization as a result of the accident. 7. Identify the main topic areas that should be included in a planned health and safety inspection of a workplace. 8. Explain how the following may be used to improve safety performance within an organization: (i) accident data (ii) safety inspections. 9. Outline factors that would determine the frequency in which health and safety inspections should be undertaken in the workplace. 10. (a) Define the term ‘safety survey’ (b) Outline the issues which should be considered when a safety survey of a workplace is to be undertaken.

111

Introduction to Health and Safety at Work 11. Outline the strengths AND weaknesses of using a checklist to complete a health and safety inspection of a workplace.

(ii) Outline the practical measures that could be taken to motivate employees to comply with health and safety procedures.

12. Outline the topics that should be included in a health and safety audit.

15. List the documents that are likely to be examined during a health and safety audit.

13. Outline the reasons why an organization should review and monitor its health and safety performance.

16. Identify the advantages AND disadvantages of carrying out a health and safety audit of an organization’s activities by: (i) an internal auditor (ii) an external auditor.

14. A health and safety audit of an organization has identiﬁed a general lack of compliance with procedures. (i) Describe the possible reasons for procedures not being followed

Appendix 7.1

Workplace inspection exercises

The following four examples are given of workplaces with numerous inadequately controlled hazards. They can be used to practise workplace inspections and risk assessments.

Figure 7.4

112

Office.

Monitoring, review and audit

Figure 7.5

Road repair.

Figure 7.6

Workshop.

113

Introduction to Health and Safety at Work

Figure 7.7

Roof repair/Unloading.

Appendix 7.2

Basic checklist of items to be covered in an area inspection

1. Access equipment

Right equipment for the job? Properly erected? Maintained?

2. Access ways

Unobstructed?

3. Chemicals

COSHH assessments OK? Exposures adequately controlled? Data sheet information available? Spillage procedure available? Properly stored? Properly disposed of?

4. Cleaning

Slip risk controlled?

5. Contractors

Are there control rules and procedures? Are they followed?

6. Eating facilities

Clean and adequate/Means of heating food?

7. Electrical equipment

Portable equipment tested? Leads tidy not damanged?

8. Ergonomics

Tasks require uncomfortable postures or actions? Frequent repetitive actions accompanying muscular strain?

9. Eye-wash bottles

Full? In date?

10. Employers’ liability insurance

Notice displayed? In date?

11. Fire exits

Unobstructed? Easily opened? Properly signed?

12. Fire extinguishers

In place? Full? Correct type?

13 Fire instructions

Posted up? Not defaced or damaged?

114

Monitoring, review and audit 14 First Aid

Suitably placed and provisioned? Appointed person? Trained ﬁrst aider?

15 Flammable liquids

Stored properly? Used properly?

16 Flooring

Even and in good condition?

17 Hand tools

Right tool for the job? In good condition?

18 Health and Safety law poster

Displayed/completed?

19 Housekeeping

Tidy, clean, well organized?

20 Ladders/step ladders

Right equipment for the job? Secure base? Correct angle? Equipment in good condition?

21 Machinery

Guards in place? Effective? Service schedules available?

22 Manual handling

Moving excessive weight? Assessments carried out? Using correct technique? Could it be eliminated or reduced?

23 New or nursing mothers

Facilities for resting?

24 Noise

Normal conversation possible? Noise assessment needed/not needed? Noise areas designated?

25 PPE

Correct type? Worn correctly? Good condition?

26 Risk assessments

Carried out? General and ﬁre? Suitable and sufﬁcient?

27 Safe systems of work

Available? Satisfactory? Followed?

28 Sharps

Safety knives used? Knives/needles/glass properly used/disposed of?

29 Vehicles

Speeding? Following correct route? Driver looks where he is going? Properly maintained? Passengers only where speciﬁcally intended with suitable seat?

30 Visual display units

Workstation assessments needed/not needed Chairs adjustable/comfortable/maintained properly? Cables properly controlled? Lighting OK? No glare?

31 Vibration

Any vibration problems with hand held machinery or with whole body from vehicle seats etc?

32 Working environment

Crowded? Too hot/cold? Ventilation? Humidity? Dusty? Lighting?

33 Welfare

Washing and toilet facilities satisfactory? Kept clean, with soap and towels/ Adequate changing facilities

34 Work at height

Working platforms ok? Access? Use of mobile elevating work platforms ok? Trussing ok?

35 Young persons

Employed? Special risk assessments?

115

8

Incident and accident investigation and reporting

8.1 Introduction This chapter is concerned with the recording of incidents and accidents at work; their investigation; the legal reporting requirements; and simple analysis of incidents to help managers beneﬁt from the investigation and recording process. Incidents and accidents rarely result from a single cause and many turn out to be complex. Most incidents involve multiple, interrelated causal factors. They can occur whenever signiﬁcant deﬁciencies, oversights, errors, omissions or unexpected changes occur. Any one of these can be the precursor of an accident or

Figure 8.1

116

A dangerous occurrence – fire.

incident. There is a value on collecting data on all incidents and potential losses as it helps to prevent more serious events. (See Chapter 5 for accident ratios and deﬁnitions.) Incidents and accidents, whether they cause damage to property or more seriously injury and/or ill-health to people, should be properly and thoroughly investigated to allow an organization to take the appropriate action to prevent a recurrence. Good investigation is a key element to making improvements in health and safety performance. Incident investigation is considered to be part of a reactive monitoring system because it is triggered after an event.

Incident and accident investigation and reporting The range of events includes: ➤ injuries and ill-health, including sickness absence ➤ damage to property, personal effects, work in progress, etc. ➤ incidents which have the potential to cause injury, ill-health or damage.

➤ An understanding of the ways people are exposed to substances or situations which can cause them harm ➤ A snapshot of what really happens e.g. why people take shortcuts or ignore safety rules ➤ Identifying deﬁciencies in the control of risks in the organization.

Each type of event gives the opportunity to:

8.2.2

➤ check performance ➤ identify underlying deﬁciencies in management systems and procedures ➤ learn from mistakes and add to the corporate memory ➤ reinforce key health and safety messages ➤ identify trends and priorities for prevention ➤ provide valuable information if there is a claim for compensation ➤ helps to meet legal requirements for reporting certain incidents to the authorities.

The legal reasons for conducting an investigation are:

8.2 Reasons for incident/accident investigation 8.2.1

Legal reasons

➤ To ensure that the organization is operating in compliance with legal requirements ➤ That it forms an essential part of the MHSW Regulation 5 requirements to plan, organize, control, monitor and review health and safety arrangements ➤ To comply with the Woolfe Report on civil action which changed the way cases are run. Full disclosure of the circumstances of an accident has to be made to the injured parties considering legal action. The fact that a thorough investigation was carried out and remedial action taken would demonstrate to a court that a company has a positive attitude to health and safety. The investigation will also provide essential information for insurers in the event of an employer’s liability or other claim.

Logic and understanding

Incident/accident investigation is based on the logic that: ➤ all incidents/accidents have causes … eliminate the cause and eliminate future incidents ➤ the direct and indirect causes of an incident/accident can be discovered through investigation ➤ corrective action indicated by the causation can be taken to eliminate future incidents/accidents. Investigation is not intended to be a mechanism for apportioning blame. There are often strong emotions associated with injury or signiﬁcant losses. It is all too easy to look for someone to blame without considering the reasons why a person behaved in a particular way. Often short cuts to working procedures that may have contributed to the accident give no personal advantage to the person injured. The short cut may have been taken out of loyalty to the organization or ignorance of a safer method. Valuable information and understanding can be gained from carrying out accident/incident investigations. These include: ➤ An understanding of how and why problems arose which caused the accident/incident

8.2.3

Benefits

There are many beneﬁts from investigating accidents/ incidents. These include: ➤ The prevention of similar events occurring again. Where the outcomes are serious injuries the enforcing authorities are likely to take a tough stance if previous warnings have been ignored ➤ The prevention of business losses due to disruption immediately after the event, loss of production, loss of business through a lowering of reputation or inability to deliver, and the costs of criminal and legal actions ➤ Improvement in employee morale and general attitudes to health and safety particularly if they have been involved in the investigations ➤ Improving management skills to improve health and safety performance throughout the organization. The case for investigating near misses and undesired circumstances may not be so obvious but it is just as useful and much easier as there are no injured people to deal with. There are no demoralized people at work or distressed families and seldom a legal action to answer.

117

Introduction to Health and Safety at Work Witnesses will be more willing to speak the truth and help with the investigation.

8.2.4

Likelihood of recurrence

Potential worst injury consequences of accident / incident Minor

What managers need to do

Serious

Major

Fatal

Certain

Managers need to: Likely

➤ communicate the type of accident and incident that needs to be reported ➤ provide a system for reporting and recording ➤ check that the proper reports are being made ➤ make appropriate records of accidents and incidents ➤ investigate all incidents and accidents reported ➤ analyse the events routinely to check for trends in performance and the prevalence of types of incident or injury ➤ monitor the system to make sure that it is working satisfactorily.

8.3 Which incidents/accidents should be investigated? 8.3.1

Injury accident

Should every accident be investigated or only those that lead to serious injury? In fact the main determinant is the potential of the accident to cause harm rather than the actual harm resulting. For example, a slip can result in an embarrassing ﬂailing of arms or, just as easily, a broken leg. The frequency of occurrence of the accident type is also important – a stream of minor cuts from paper needs looking into. As it is not possible to determine the potential for harm simply from the resulting injury, the only really sensible solution is to investigate all accidents. The amount of time and effort spent on the investigation should, however, vary depending on the level of risk (severity of potential harm, frequency of occurrence). The most effort should be focused on signiﬁcant events involving serious injury, ill-health or losses and events which have the potential for multiple or serious harm to people or substantial losses. These factors should become clear during the accident investigation and be used to guide how much time should be taken. The following table has been developed by the HSE to help to determine the level of investigation which is appropriate. The worst case scenario for the consequences should be considered in using the table. A particular incident like a scaffold collapse may not have caused an injury but had the potential to cause major or fatal injuries.

118

Possible Unlikely Rare

Risk

Minimal

Low

Medium

High

Investigation level

Minimal level

Low level

Medium level

High level

➤ In a minimal level investigation, the relevant supervisor will look into the circumstances of the accident/ incident and try to learn any lessons which will prevent future incidents ➤ A low level investigation will involve a short investigation by the relevant supervisor or line manager into the circumstances and immediate underlying and root causes of the accident/incident, to try to prevent a recurrence and to learn any general lessons ➤ A medium level investigation will involve a more detailed investigation by the relevant supervisor or line manager, the health and safety adviser and employee representatives and will look for the immediate, underlying and root causes ➤ A high level investigation will involve a team-based investigation, involving supervisors or line managers, health and safety advisers and employee representatives. It will be carried out under the supervision of senior management or directors and will look for the immediate, underlying and root causes.

8.4 Investigations and causes of incidents 8.4.1

Who should investigate?

Investigations should be led by supervisors, line managers or other people with sufﬁcient status and knowledge to make recommendations that will be respected by the organization. The person to lead many investigations

Incident and accident investigation and reporting will be the department manager or supervisor of the person/area involved because they: ➤ know about the situation ➤ know most about the employees ➤ have a personal interest in preventing further incidents/ accidents affecting ‘their’ people, equipment, area, materials ➤ can take immediate action to prevent a similar incident ➤ can communicate most effectively with the other employees concerned ➤ can demonstrate practical concern for employees and control over the immediate work situation.

8.4.2

When should the investigation be conducted?

The investigation should be carried out as soon as possible after the incident to allow the maximum amount of information to be obtained. There may be difﬁculties which should be considered in setting up the investigation quickly – if, for example, the victim is removed from the site of the accident, or if there is a lack of a particular expert. An immediate investigation is advantageous because: ➤ factors are fresh in the minds of witnesses ➤ witnesses have had less time to talk (there is an almost automatic tendency for people to adjust their story of the events to bring it into line with a consensus view) ➤ physical conditions have had less time to change ➤ more people are likely to be available, for example, delivery drivers, contractors and visitors who will quickly disperse following an incident making contact very difﬁcult ➤ there will probably be the opportunity to take immediate action to prevent a recurrence and to demonstrate management commitment to improvement ➤ immediate information from the person suffering the accident often proves to be most useful. Consideration should be given to asking the person to return to site for the accident investigation if they are physically able, rather than wait for them to return to work. A second option, although not as valuable, would be to visit the injured person at home or even in hospital (with their permission) to discuss the accident.

8.4.3

Investigation method

There are four basic elements to a sound investigation: 1. 2.

collect facts about what has occurred assemble, and analyse the information obtained

Figure 8.2 happen. 3.

4.

Near miss event likely – accident waiting to

compare the information with acceptable industry and company standards and legal requirements to draw conclusions implement the ﬁndings and monitor progress.

Information should be gathered from all available sources, for example, witnesses, supervisors, physical conditions, hazard data sheets, written systems of work, training records, etc. The amount of time spent should not, however, be disproportionate to the risk. The aim of the investigation should be to explore the situation for possible underlying factors, in addition to the immediately obvious causes of the accident. For example, in a machinery accident it would not be sufﬁcient to conclude that an accident occurred because a machine was inadequately guarded. It is necessary to look into the possible underlying system failure that may have occurred. Investigations have three facets, which are particularly valuable and can be used to check against each other: ➤ direct observation of the scene, premises, workplace, relationship of components, materials and substances being used, possible reconstruction

119

Introduction to Health and Safety at Work of events, and injuries or condition of the person concerned ➤ documents including written instructions, training records, procedures, safe operating systems, risk assessments, policies, records of inspections or test and examinations carried out ➤ interviews (including written statements) with persons injured, witnesses, people who have carried out similar functions or examinations and tests on the equipment involved and people with specialist knowledge.

Immediate causes A detailed investigation should look at the following factors as they can provide useful information about immediate causes that have been manifested in the incident/accident. ➤ Personal factors: ➤ behaviour of the people involved ➤ suitability of people doing the work ➤ training and competence ➤ Task factors: ➤ workplace conditions and precautions or controls ➤ actual method of work adopted at the time ➤ ergonomic factors ➤ normal working practice either written or customary.

Underlying and root causes A thorough investigation should also look at the following factors as they can provide useful information about underlying and root causes that have been manifested in the incident/accident: Underlying causes are the less obvious system or organizational reasons for an accident or incident such as: ➤ pre-start-up machinery checks were not made by supervisors ➤ the hazard had not been considered in the risk assessment ➤ there was no suitable method statement ➤ pressures of production had been more important ➤ the employee was under a lot of personal pressure at the time ➤ have there been previous similar incidents? ➤ was there adequate supervision, control and coordination of the work involved?

➤ the adequacy and quality of communications and information ➤ deﬁciencies in risk assessments, plans and control systems ➤ deﬁciencies in monitoring and measurement of work activities ➤ quality and frequency of reviews and audits.

8.4.4

Investigation interview techniques

It must be made clear at the outset and during the course of the interview that the aim is not to apportion blame but to discover the facts and use them to prevent similar accidents in the future. A witness should be given the opportunity to explain what happened in their own way without too much interruption and suggestion. Questions should then be asked to elicit more information. These should be of the open type, which do not suggest the answer. Questions starting with the words in Figure 8.3 are useful. ‘Why’ should not be used at this stage. The facts should be gathered ﬁrst, with notes being taken at the end of the explanation. The investigator should then read them or give a summary back to the witness, indicating clearly that they are prepared to alter the notes, if the witness is not content with them. If possible, indication should be given to the witness about immediate actions that will be taken to prevent a similar occurrence and that there could be further improvements depending on the outcome of the investigation. Accidents can often be very upsetting for witnesses, which should be borne in mind. This does not mean they will not be prepared to talk about what has happened. They may in fact wish to help, but questions should be sensitive; upsetting the witness further should be avoided.

Root causes involve an initiating event or failing from which all other causes or failings arise. Root causes are generally management, planning or organizational failings including: ➤ quality of the health and safety policy and procedures ➤ quality of consultation and cooperation of employees

120

Figure 8.3

Questions to be asked in an investigation.

Incident and accident investigation and reporting 8.4.5

Comparison with relevant standards

There are usually suitable and relevant standards which may come from the HSE, industry or the organization itself. These should be carefully considered to see if: ➤ suitable standards are available to cover legal standards and the controls required by the risk assessments ➤ the standards are sufﬁcient and available to the organization ➤ the standards were implemented in practice ➤ the standards were implemented, why was there a failure? ➤ changes should be made to the standards.

8.4.6

Recommendations

The investigation should have highlighted both immediate causes and underlying causes. Recommendations, both for immediate action and for longer-term improvements, should come out of this, but it may be necessary to ensure that the report goes further up the management chain if the improvements recommended require authorization, which cannot be given by the investigating team.

8.4.7

Follow-up

It is essential that a follow-up is made to check on the implementation of the recommendations. It is also necessary to review the effect of the recommendations to check whether they have achieved the desired result and whether they have had unforeseen ‘knock-on’ effects, creating additional risks and problems.

8.4.8

Use of information

The accident investigation should be used to generate recommendations but should also be used to generate safety awareness. The investigation report or a summary should therefore be circulated locally to relevant people and, when appropriate, summaries circulated throughout the organization. The accident does not need to have resulted in a three-day lost time injury for this system to be used.

8.4.9

Training

A number of people will potentially be involved in accident investigation. For most of these people it will only be necessary on very few occasions. Training guidance and help will therefore be required. Training can be provided in accident investigation in courses run on site and also in numerous off-site venues. Computer-based training

courses are also available. These are intended to provide refresher training on an individual basis or complete training at ofﬁce sites, for example, where it may not be feasible to provide practical training.

8.4.10

Investigation form

Headings which could be used to compile an accident/ incident investigation form are given below: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

date and location of accident circumstances of accident immediate cause of accident underlying cause of accident immediate action taken recommendation for further improvement report circulation list date of investigation signature of investigation team leader names of investigating team.

Follow-up ➤ were the recommendations implemented? ➤ were the recommendations effective? An example of an investigation form using 16 different causes of accidents for analysis purposes is shown in Appendix 8.1.

8.5 Legal recording and reporting requirements 8.5.1

Accident book

Under the Social Security (Claims and Payments) Regulations 1979, regulation 25, employers must keep a record of accidents at premises where more than ten people are employed. Anyone injured at work is required to inform the employer and record information on the accident in an accident book, including a statement on how the accident happened. The employer is required to investigate the cause and enter this in the accident book if they discover anything that differs from the entry made by the employee. The purpose of this record is to ensure that information is available if a claim is made for compensation. The HSE has produced a new Accident Book BI 510 in May 2003 with notes on these Regulations, and the Reporting of Injuries Diseases and Dangerous Occurrences Regulations 1995 (RIDDOR) (see Figure 8.4) and now complies with the Data Protection Act 1998.

121

Introduction to Health and Safety at Work

Figure 8.4 The 0-7176-2603-2

8.5.2

Accident

Book

BI

510

ISBN

RIDDOR

RIDDOR requires employers, the self-employed and those in control of premises, to report certain more serious accidents and incidents to the HSE or other enforcing authority and to keep a record. There are no exemptions for small organizations. A full summary of the Regulations is given in Chapter 17. The reporting and recording requirements are as follows:

Death or major injury If an accident occurs at work and: ➤ an employee, or self-employed person working on the premise is killed or suffers a major injury (including the effects of physical violence) (see Chapter 17 under RIDDOR for deﬁnition of major injury) ➤ a member of the public is killed or taken to hospital. The responsible person must notify the enforcing authority without delay by the quickest practicable means, for example, telephone. They will need to give brief details about the organization, the injured person(s) and the circumstances of the accident and, within ten days, the responsible person must also send a completed accident report form, F2508.

Over three-day lost time injury If there is an accident connected with work (including physical violence) and an employee, or self-employed

122

Figure 8.5

RIDDOR leaflet from HSE Books.

person working on the premises, suffers an injury and is away from work or not doing their normal duties for more than three days (including weekends, rest days or holidays) but not counting the day of the accident, the responsible person must send a completed accident report form, F2508, to the enforcing authority within ten days.

Disease If a doctor notiﬁes the responsible person that an employee suffers from a reportable work-related disease a completed disease report form, F2508A, must be sent to the enforcing authority. A summary is included in Chapter 17 and a full list is included with a pad of report forms. The HSE InfoLine or the Incident Contact Centre can be contacted to check whether a particular disease is reportable.

Dangerous occurrence If an incident happens which does not result in a reportable injury, but obviously could have done, it could be a Dangerous Occurrence as deﬁned by a list in the regulations (see Chapter 17 for a summary of Dangerous Occurrences). All Dangerous Occurrences must be reported immediately by, for example, telephone, to the enforcing authorities. The HSE InfoLine or the Incident Contact Centre can be contacted to check whether a dangerous occurrence is reportable. A completed accident report form, F2508, must be sent to the enforcing authorities within ten days.

Incident and accident investigation and reporting 8.5.3

Whom to report to

Until 2001 all reports had to be made to the local HSE ofﬁce or local authority. This can still be done, but there is a centralized national system, called the Incident Contact Centre (ICC), which is a joint venture between the HSE and local authorities. All reports sent locally are now passed on to the ICC. This means that employers no longer need be concerned about which authority to report to, as all incidents can be reported to the ICC directly. Reports can be sent by telephone, fax, the Internet, or by post. If reporting by the Internet or telephone a copy of the report is sent to the responsible person for correction, if necessary, and for their records. ➤ Postal reports should be sent to: Incident Contact Centre Caerphilly Business Park Caerphilly CF83 3GG ➤ For Internet reports go to: www.riddor.gov.uk or link through www.hse.gov.uk ➤ By telephone (charged at local rates) 0845 300 9923 ➤ By fax (charged at local rates) 0845 300 9924 ➤ By email: [email protected]

8.6 Internal systems for collecting and analysing incident data

➤ how the incident data should be analysed and at what intervals ➤ the arrangements to ensure that action is taken on the data provided. The data should seek to answer the following questions: ➤ are failure incidents occurring, including injuries, illhealth and other loss incidents? ➤ where are they occurring? ➤ what is the nature of the failures? ➤ how serious are they? ➤ what were the potential consequences? ➤ what are the reasons for the failures? ➤ how much has it cost? ➤ what improvements in controls and the management system are required? ➤ how do these issues vary with time? ➤ is the organization getting better or worse?

Type of incident Most organizations will want to collect: ➤ ➤ ➤ ➤

all injury accidents cases of ill-health sickness absence damage to property, personal effects and work in progress ➤ incidents with the potential to cause serious injury, ill-health or damage. Not all of these are required by law, but this should not deter the organization that wishes to control hazards effectively.

Introduction Managers need effective internal systems to know whether the organization is getting better or worse; to know what is happening and why; and to assess whether objectives are being achieved. Chapter 16 deals with monitoring generally, but here, the basic requirements of a collection and analysis system for incidents are discussed. The incident report form (discussed earlier) is the basic starting point for any internal system. Each organization needs to lay down what the system involves and who is responsible to do each part of the procedure. This will involve: ➤ what type of incidents should be reported ➤ who completes the incident report form – normally the manager responsible for the investigation ➤ how copies should be circulated in the organization ➤ who is responsible to provide management measurement data

Analysis All the information, whether in accident books or report forms, will need to be analysed so that useful management data can be prepared. Many organizations look at analysis each month and annually. However, where there are very few incidents, quarterly may be sufﬁcient. The health and safety information should be used alongside other business measures and should receive equal status. There are several ways in which data can be analysed and presented. The most common ways are: ➤ by causation using the classiﬁcation used on the RIDDOR form F2508. This has been used on the example accident report form (see Appendix 8.1) ➤ by nature of the injury, such as cuts, abrasions, asphyxiation, amputations ➤ by the part of the body affected, such as hands, arms, feet, lower leg, upper leg, head, eyes, back

123

Introduction to Health and Safety at Work

➤ ➤ ➤ ➤

and so on. Sub-divisions of these categories could be useful if there were sufﬁcient incidents by age and experience at the job by time of day by occupation or location of the job by type of equipment used.

There are a number of up-to-date computer recording programs which can be used to manipulate the data if signiﬁcant numbers are involved. The trends can be shown against monthly, quarterly and annual past performance of, preferably, the same organization. If indices are calculated, such as Incident Rate, comparisons can be made nationally with HSE ﬁgures and with other similar organizations or businesses in the same industrial group. This is really only of major value to larger organizations with signiﬁcant numbers of events. (See Chapter 4 for more information on deﬁnitions and calculation of Incident Rates.) The HSE produces annual bulletins of national performance plus a detailed statistical report, which can be used for comparisons. There are difﬁculties in comparisons across Europe and say, with the USA, where the deﬁnitions of accidents or time lost vary. Reports should be prepared with simple tables and graphs showing trends and comparisons. Line graphs, bar charts and pie charts are all used quite extensively with good effect. All analysis reports should be made available to employees as well as managers. This can often be done through the health and safety committee and safety representatives, where they exist, or directly to all employees in small organizations. Other routine meetings, team brieﬁngs and notice boards can all be used to communicate the message. It is particularly important to make sure that any actions recommended or highlighted by the reports are taken quickly and employees kept informed.

8.7 Compensation and insurance issues Accidents arising out of the organization’s activities resulting in injuries to people and incidents resulting in damage to property can lead to compensation claims. The second objective of an investigation should be to collect and record relevant information for the purposes of dealing with any claim. It must be remembered that, in the longer term, prevention is the best way to reduce claims and must be the ﬁrst objective in the investigation. An overzealous approach to gathering information concentrating on the compensation aspect can, in fact, prompt a claim from the injured party where there was no particular intention to take this route before the investigation. Nevertheless, relevant information should

124

be collected. Sticking to the collection of facts is usually the best approach. As mentioned earlier the legal system in England and Wales changed dramatically with the introduction of the Woolf reforms in 1999. These reforms apply to injury claims. This date was feared by many because of the uncertainty and the fact that the pre-action protocols were very demanding. The essence of the pre-legal action protocols is as follows: 1. 2.

3.

‘Letter of claim’ to be acknowledged within 21 days 90 days from date of acknowledgement to either accept liability or deny. If liability is denied then full reasons must be given Agreement to be reached on using a single expert.

The overriding message is that to comply with the protocols quick action is necessary. It is also vitally important that records are accurately kept and accessible. Lord Woolf made it clear in his instructions to the judiciary that there should be very little leeway given to claimants and defendants who did not comply. What has been the effect of these reforms on day to day activity? At the present time there has been a dramatic drop in the number of cases moving to litigation. Whilst this was the primary objective of the reforms, the actual drop is far more signiﬁcant than any one anticipated. In large part this may simply be due to general unfamiliarity with the new rules and we can expect an increase in litigation as time goes by. However some of the positive effects have been ➤ the elimination of speculative actions due to the requirement to fully outline the claimant’s case in the letter of claim ➤ earlier and more comprehensive details of the claim allow a more focused investigation and response ➤ ‘Part 36 offers’ (payments into court) seem to be having greater effect in deterring claimants from pursuing litigation ➤ overall faster settlement. The negative effects have principally arisen from failure to comply with the timescales particularly relating to the gathering of evidence and records and having no time therefore to construct a proper defence. Whilst it is still too early to make a full assessment of the impact of Woolf there are reasons to be cautiously optimistic. Appendix 8.2 provides a checklist of headings, which may assist in the collection of information. It is not expected that all accidents and incidents will be investigated in depth and a dossier with full information prepared. Judgement has to be applied as to which incidents might

Incident and accident investigation and reporting give rise to a claim and when a full record of information is required. All accident report forms should include the names of all witnesses as a minimum. Where the injury is likely to give rise to lost time, a photograph(s) of the situation should be taken.

8.8 Practice NEBOSH questions for Chapter 8 1. (a) Give FOUR reasons why an organization should have a system for the internal reporting of accidents (b) Outline factors that may discourage employees from reporting accidents at work. 2. An employee has been seriously injured after being struck by a reversing vehicle in a loading bay. (i) Give FOUR reasons why the accident should be investigated by the person’s employer (ii) Outline the information that should be included in the investigation report (iii) Outline FOUR possible immediate causes and FOUR possible underlying (root) causes of the accident. 3. State the issues that should be included in a typical workplace accident reporting procedure. 4. An organization has decided to conduct an internal investigation of an accident in which an employee was injured following the collapse of storage racking. (i) Outline FOUR beneﬁts to the organization of investigating the accident (ii) Giving reasons in EACH case, identify FOUR people who may be considered useful members of the investigation team (iii) Having deﬁned the team, outline the factors that should be considered when planning the investigation. 5. Explain the purpose and beneﬁts of collecting ‘nearmiss’ incident data. 6. Explain the differences between the immediate and the root (underlying) causes of an accident. 7. Outline the immediate and longer term actions that should be taken following a major injury accident at work. 8. An employee slipped on a patch of oil on a warehouse ﬂoor and was admitted to hospital where he

remained for several days. The oil was found close to a stack of pallets that had been left abandoned on the designated pedestrian walkway. (i) Outline the legal requirements for reporting the accident to the enforcing authority (ii) Identify the possible immediate AND root causes of the accident (iii) Outline ways in which management could demonstrate their commitment to improve health and safety standards in the workplace following the accident. 9. Outline the key points that should be covered in a training session for employees on the reporting of accidents/incidents. 10. With reference to the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995: (i) State the legal requirements for reporting a fatality resulting from an accident at work to an enforcing authority (ii) Outline THREE further categories of work-related injury (other than fatal injuries) that are reportable (iii) State the requirements for reporting an ‘over three-day’ injury. 11. With reference to the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995: (i) List FOUR types of major injury (ii) Outline the procedures for reporting a major injury to an enforcing authority. 12. With reference to the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR) 1995: (i) Explain, using TWO examples, the meaning of the term ‘dangerous occurrence’ (ii) State the requirements for reporting a dangerous occurrence. 13. (a) Identify TWO ill-health conditions that are reportable under the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations (RIDDOR) 1995 (b) Outline reasons why employers should keep records of occupational ill-health amongst employees. 14. An employee is claiming compensation for injuries received during an accident involving a fork-lift truck. Identify the documented information that the employer might draw together when preparing a possible defence against the claim.

125

Introduction to Health and Safety at Work Appendix 8.1

Injury report form

INCIDENT/ACCIDENT REPORT INJURED PERSON:........................................................... Date of Accident: / /20 Time.......... am/pm POSITION:......................................................................... Place of Incident: ............................................................. DEPARTMENT:.................................................................. Details of Injury: ............................................................... Investigation carried out by: ......................................................................................................................................... Position: ............................................................................ Estimated Absence: ......................................................... Brief details of Accident (A detailed report together with diagrams, photographs and any witness statements should be attached where necessary. Please complete all details requested overleaf.)

Immediate Causes

Underlying Cause

Conclusions (How can we prevent this kind of incident/accident occurring again?)

Action to be taken:

Completion Date:

/

/20

IMPORTANT Please ensure that an accident investigation and report is completed and forwarded to Human Resources within 48 hours of the accident occurring.

Remember that accidents involving major injuries or dangerous occurrences have to be notiﬁed immediately by telephone to the HSE/Local authority.

Signature of manager making report: ............................................................................ Copies: Personnel Manager Health and Safety Manager Date: / /20 Payroll Controller

INJURED PERSON: Surname ................................................................... Forenames ............................................... Male/Female Home address ........................................................................................................................................ Age ............. Employee 䊐

126

Agency Temp 䊐

Contractor 䊐

Visitor 䊐

Youth Trainee 䊐

(Tick one box)

Incident and accident investigation and reporting Kind of Accident Indicate what kind of accident led to the injury or condition (tick one box)

Contact with moving machinery or material being machined

Injured while handling lifting or carrying 1

Struck by moving, ﬂying, or falling object

Drowning or asphyxiation 5

Slip, trip or fall on same level 2

Struck by moving vehicle

9 Exposure to or contact with harmful substance

6 Fall from height indicate approx distance of fall.........m

3 Struck against something ﬁxed or stationary

Contact with electricity or an electrical discharge

10 Exposure to ﬁre

4

14 Violence, physically assaulted by a person

7 Trapped by something collapsing

13 Injured by an animal

11 Exposure to an explosion

15 Other kind of accident

8

12

16

Detail any machinery, chemicals, tools etc. involved

Accident first reported to:

Name

Position &

Dept

First Aid/medical attention by:

First Aider Name

Dept

Doctor Name Medical centre WITNESSES Name

Position & Dept

Hospital

Statement obtained (yes/no) Attach all statements taken yes/no yes/no yes/no yes/no

For Ofﬁce use only If relevant:

Date reported to HSE/LA

a) by telephone

.../.../20

b) on form F2508

.../.../20

Date reported to organization’s insurers

.../.../20

WERE THE RECOMMENDATIONS EFFECTIVE ? YES/NO IF NO SAY WHAT ACTION SHOULD BE TAKEN.

127

Introduction to Health and Safety at Work Appendix 8.2

Information for insurance/compensation claims

Information for insurance/compensation purposes following accident or incident

➤ Housekeeping records ➤ Hazard warning signs or notices (Trafﬁc Routes).

Factual information needs to be collected where there is the likelihood of some form of claim either against the organization or by the organization (e.g. damage to equipment). This aspect should be considered as a second objective in accident investigation, the ﬁrst being to learn from the accident to reduce the possibility of accidents occurring in the future.

Section B – Provision and Use of Work Equipment Regulations 1998

Workplace Claims ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

➤

Accident book entry First aider report Surgery record Foreman/supervisor accident report Safety representatives accident report RIDDOR report to HSE Other communications between defendants and HSE Minutes of Health and Safety Committee meeting(s) where accident/matter considered Report to DSS Documents listed above relative to any previous accident/matter identiﬁed by the claimant and relied upon as proof of negligence Earnings information where defendant is employer.

Documents produced to comply with requirements of the Management of Health and Safety at Work Regulations 1999 ➤ Pre-accident Risk Assessment ➤ Post-accident Re-Assessment ➤ Accident Investigation Report prepared in implementing the requirements; Health Surveillance Records in appropriate cases; Information provided to employees ➤ Documents relating to the employee’s health and safety training.

WORKPLACE CLAIMS – Examples of disclosure where specific regulations apply Section A – Workplace (Health Safety and Welfare) Regulations 1992 ➤ Repair and maintenance records

128

➤ Manufacturers’ speciﬁcations and instructions in respect of relevant work equipment establishing its suitability to comply with Regulation 5 ➤ Maintenance log/maintenance records required; Documents providing information and instructions to employees; Documents provided to the employee in respect of training for use ➤ Any notice, sign or document relied upon as a defence to alleged breaches dealing with controls and control systems. Section C – Personal Protective Equipment at Work Regulations 1992 ➤ Documents relating to the assessment of the PPE ➤ Documents relating to the maintenance and replacement of PPE ➤ Record of maintenance procedures for PPE ➤ Records of tests and examinations of PPE ➤ Documents providing information, instruction and training in relation to the PPE ➤ Instructions for use of Personal Protective Equipment to include the manufacturers’ instructions Section D – Manual Handling Operations Regulations 1992 ➤ Manual Handling Risk Assessment carried out ➤ Re-assessment carried out post-accident ➤ Documents showing the information provided to the employee to give general indications related to the load and precise indications on the weight of the load and the heaviest side of the load if the centre of gravity was not positioned centrally ➤ Documents relating to training in respect of manual handling operations and training records Section E – Health and Safety (Display Screen Equipment) Regulations 1992 ➤ Analysis of work stations to assess and reduce risks ➤ Re-assessment of analysis of work stations to assess and reduce risks following development of symptoms by the claimant

Incident and accident investigation and reporting ➤ Documents detailing the provision of training including training records ➤ Documents providing information to employees. Section F – Control of Substances Hazardous to Health Regulations 2002 ➤ Risk assessments and any reviews ➤ Copy labels from containers used for storage handling and disposal of carcinogens ➤ Warning signs identifying designation of areas and installations which may be contaminated by carcinogens ➤ Documents relating to the assessment of the Personal Protective Equipment ➤ Documents relating to the maintenance and replacement of Personal Protective Equipment ➤ Record of maintenance procedures for Personal Protective Equipment

➤ Records of tests and examinations of Personal Protective Equipment ➤ Documents providing information, instruction and training in relation to the Personal Protective Equipment ➤ Instructions for use of Personal Protective Equipment to include the manufacturers’ instructions ➤ Air monitoring records for substances assigned a workplace exposure limit ➤ Maintenance examination and test of control measures records ➤ Monitoring records ➤ Health surveillance records ➤ Documents detailing information, instruction and training including training records for employees ➤ Labels and Health and Safety data sheets supplied to the employers

129

9

Movement of people and vehicles – hazards and control

9.1 Introduction People are most often involved in accidents as they walk around the workplace or when they come into contact with vehicles in or around the workplace. It is therefore important to understand the various common accident

causes and the control strategies that can be employed to reduce them. Slips, trips and falls account for the majority of accidents to pedestrians and the more serious accidents between pedestrians and vehicles can often be traced back to excessive speed or other unsafe vehicle practices, such as lack of driver training. Many of the risks associated with these hazards can be signiﬁcantly reduced by an effective management system.

9.2 Hazards to pedestrians The most common hazards to pedestrians at work are slips, trips and falls on the same level, falls from height, collisions with moving vehicles, being struck by moving, falling or ﬂying objects and striking against ﬁxed or stationary objects. Each of these will be considered in turn, including the conditions and environment in which the particular hazard may arise.

9.2.1

Figure 9.1

130

Tripping hazards.

Slips, trips and falls on the same level

These are the most common of the hazards facing pedestrians and accounted for 30% each year of all the major accidents and 20% of over three-day injuries reported to the HSE. It has been estimated that the annual cost of these accidents to the nation is £750 m and a direct cost to employers of £300 m. The highest reported injuries are reported in the food and related industries. Older workers, especially women, are the most severely injured group from falls resulting in fractures of the hips and/or femur. Civil compensation claims are becoming more common and costly to employers and such claims are now being made

Movement of people and vehicles – hazards and control ➤ poor housekeeping – obstacles left on walkways, rubbish not removed regularly ➤ poor lighting levels – particularly near steps or other changes in level ➤ sloping or uneven ﬂoors – particularly where there is poor lighting or no handrails ➤ unsuitable footwear – shoes with a slippery sole or lack of ankle support. The vast majority of major accidents involving slips, trips and falls on the same level result in dislocated or fractured bones.

9.2.2

Figure 9.2 slipping.

Cleaning must be done carefully to prevent

by members of the public who have tripped on uneven paving slabs on pavements or in shopping centres. The Health and Safety Commission has been so concerned at the large number of such accidents that it has identiﬁed slips, trips and falls on the same level as a key risk area. The costs of slips, trips and falls on the same level are high to the injured employee (lost income and pain), the employer (direct and indirect costs including lost production) and to society as a whole in terms of health and social security costs. Slip hazards are caused by:

Falls from work at height

These are the most common cause of serious injury or death in the construction industry and the topic is covered in Chapter 16. These accidents are often concerned with falls of greater than about 2 m and often result in fractured bones, serious head injuries, loss of consciousness and death. Twenty-ﬁve per cent of all deaths at work and 19% of all major accidents are due to falls from a height. Falls down staircases and stairways, through fragile surfaces, off landings and stepladders and from vehicles, all come into this category. Injury, sometimes serious, can also result from falls below 2 m, for example, using swivel chairs for access to high shelves.

9.2.3

Collisions with moving vehicles

➤ wet or dusty ﬂoors ➤ the spillage of wet or dry substances – oil, water, ﬂour dust and plastic pellets used in plastic manufacture ➤ loose mats on slippery ﬂoors ➤ wet and/or icy weather conditions ➤ unsuitable footwear or ﬂoor coverings or sloping ﬂoors.

These can occur within the workplace premises or on the access roads around the building. It is a particular problem where there is no separation between pedestrians and vehicles or where vehicles are speeding. Poor lighting, blind corners, the lack of warning signs and barriers at road crossing points also increase the risk of this type of accident. Eighteen per cent of fatalities at work are caused by collisions between pedestrians and moving vehicles with the greatest number occurring in the service sector (primarily in retail and warehouse activities).

Trip hazards are caused by:

9.2.4

➤ loose ﬂoorboards or carpets ➤ obstructions, low walls, low ﬁxtures on the ﬂoor ➤ cables or trailing leads across walkways or uneven surfaces. Leads to portable electrical hand tools and other electrical appliances (vacuum cleaners and overhead projectors). Raised telephone and electrical sockets are also a serious trip hazard (this can be a signiﬁcant problem when the display screen workstations are re-orientated in an ofﬁce) ➤ rugs and mats – particularly when worn or placed on a polished surface

This causes 18% of fatalities at work and is the second highest cause of fatality in the construction industry. It also causes 15% of all major and 14% of over three-day accidents. Moving objects include, articles being moved, moving parts of machinery or conveyor belt systems, and ﬂying objects are often generated by the disintegration of a moving part or a failure of a system under pressure. Falling objects are a major problem in construction (due to careless working at height) and in warehouse work (due to careless stacking of pallets on racking). The head

Being struck by moving, falling or flying objects

131

Introduction to Health and Safety at Work is particularly vulnerable to these hazards. Items falling off high shelves and moving loads are also signiﬁcant hazards in many sectors of industry.

9.2.5

Striking against fixed or stationary objects

This accounts for between 1200 and 1400 major accidents each year. Injuries are caused to a person either by colliding with a ﬁxed part of the building structure, work in progress, a machine member or a stationary vehicle or by falling against such objects. The head appears to be the most vulnerable part of the body to this particular hazard and this is invariably caused by the misjudgement of the height of an obstacle. Concussion in a mild form is the most common outcome and a medical check-up is normally recommended. It is a very common injury during maintenance operations when there is, perhaps, less familiarity with particular space restrictions around a machine. Effective solutions to all these hazards need not be expensive, time consuming or complicated. Employee awareness and common sense combined with a good housekeeping regime will solve many of the problems.

9.3 Control strategies for pedestrian hazards 9.3.1

Slips, trips and falls on the same level

These may be prevented or, at least, reduced by several control strategies. These and all the other pedestrian hazards discussed should be included in the workplace risk assessments required under the Management of Health and Safety at Work Regulations by identifying slip or trip hazards, such as poor or uneven ﬂoor/pavement surfaces, badly lit stairways and puddles from leaking roofs. There is also a legal requirement in the Workplace (Health, Safety and Welfare) Regulations for all ﬂoors to be suitable, in good condition and free from obstructions. Trafﬁc routes must be so organized that people can move around the workplace safely. The key elements of a health and safety management system are as relevant to these as to any other hazards: ➤ planning – remove or minimize the risks by using appropriate control measures and deﬁned working practices (e.g. covering all trailing leads) ➤ organization – involve employees and supervisors in the planning process by deﬁning responsibility for keeping given areas tidy and free from trip hazards ➤ control – record all cleaning and maintenance work. Ensure that anti-slip covers and cappings are placed

132

on stairs, ladders, catwalks, kitchen ﬂoors and smooth walkways. Use warning signs when ﬂoor surfaces have recently been washed ➤ monitoring and review – carry out regular safety audits of cleaning and housekeeping procedures and include trip hazards in safety surveys. Check on accident records to see whether there has been an improvement or if an accident black spot may be identiﬁed. Slip and trip accidents are a major problem for large retail stores both for customers and employees. The provision of non-slip ﬂooring, a good standard of lighting and minimizing the need to block aisles during the re-stocking of merchandise are typical measures that many stores use to reduce such accidents. Other measures include the wearing of suitable footwear by employees, adequate handrails on stairways, the highlighting of any ﬂoor level changes and procedures to ensure a quick and effective response to any reports of ﬂoor damage or spillages. Good housekeeping procedures are essential. The design of the store layout and any associated warehouse can also ensure a reduction in all types of accidents. Many of these measures are valid for a range of workplaces.

9.3.2

Falls from work at height

These may be controlled by the use of suitable guardrails and barriers and also by the application of the hierarchy of controls discussed in Chapters 6 and 16 which is: ➤ remove the possibility of falling a distance that could cause personal injury (e.g. by undertaking the work at ground level)

Figure 9.3

Falling from a height – tower scaffold.

Movement of people and vehicles – hazards and control ➤ protect against the hazard of falling a distance that could cause personal injury (e.g. by using handrails) ➤ stop the person from falling a distance that could cause personal injury (e.g. by the provision of safety harnesses) ➤ mitigate the consequences of falling a distance that could cause personal injury (e.g. by the use of air bags).

being loaded or unloaded. It is important that separate doorways are provided for pedestrians and vehicles and all such doorways should be provided with a vision panel and an indication of the safe clearance height, if used by vehicles. Finally, the enforcement of a sensible speed limit, coupled where practicable, with speed governing devices, is another effective control measure.

The principal means of preventing falls of people or materials includes the use of fencing, guardrails, toe boards, working platforms, access boards and ladder hoops. Safety nets and safety harnesses should only be used when all other possibilities are not practical. The use of banisters on open sides of stairways and handrails ﬁtted on adjacent walls will also help to prevent people from falling. Holes in ﬂoors and pits should always be fenced or adequately covered. Precautions should be taken when working on fragile surfaces (see Chapter 16 for details). Permanent staircases are also a source of accidents included within this category of falling from a height and the following design and safety features will help to reduce the risk of such accidents:

9.3.4

➤ adequate width of the stairway, depth of the tread and provision of landings and banisters or handrails and intermediate rails. The treads and risers should always be of uniform size throughout the staircase and designed to meet Building Regulations requirements for angle of incline (i.e. steepness of staircase) ➤ provision of non-slip surfaces and reﬂective edging ➤ adequate lighting ➤ adequate maintenance ➤ special or alternative provision for disabled people (for example, personnel elevator at the side of the staircase). Great care should be used when people are loading or unloading vehicles, as far as possible people should avoid climbing onto vehicles or their loads. For example sheeting of lorries should be carried out in designated places using properly designed access equipment.

9.3.3

Collisions with moving vehicles

These are best prevented by completely separating pedestrians and vehicles, providing well marked, protected and laid out pedestrian walkways. People should cross roads by designated and clearly marked pedestrian crossings. Suitable guardrails and barriers should be erected at entrances and exits from buildings and at ‘blind’ corners at the end of racking in warehouses. Particular care must be taken in areas where lorries are

Being struck by moving, falling or flying objects

These may be prevented by guarding or fencing the moving part (as discussed in Chapter 9) or by adopting the measures outlined for construction work (Chapter 16). Both construction workers and members of the public need to be protected from the hazards associated with falling objects. Both groups should be protected by the use of covered walkways or suitable netting to catch falling debris where this is a signiﬁcant hazard. Waste material should be brought to ground level by the use of chutes or hoists. Waste should not be thrown from a height and only minimal quantities of building materials should be stored on working platforms. Appropriate personal protective equipment, such as hard hats or safety glasses, should be worn at all times when construction operations are taking place. It is often possible to remove high-level storage in ofﬁces and provide driver protection on lift truck cabs in warehouses. (See the section on fork lift trucks later in this chapter.) Storage racking is particularly vulnerable and should be strong and stable enough for the loads it has to carry. Damage from vehicles in a warehouse can easily weaken the structure and cause collapse. Uprights need protection, particularly at corners. The following action can be taken to keep racking serviceable: ➤ inspect them regularly and encourage workers to report any problems ➤ post notices with maximum permissible loads and never exceed the loading ➤ use good pallets and safe stacking methods ➤ band, box or wrap articles to prevent items falling ➤ set limits on the height of stacks and regularly inspect to make sure that limits are being followed ➤ provide instruction and training for staff and special procedures for difﬁcult objects.

9.3.5

Striking against fixed or stationary objects

This can only be effectively controlled by: ➤ having good standards of lighting and housekeeping ➤ deﬁning walkways and making sure they are used

133

Introduction to Health and Safety at Work High level

Barrier

Barriers to personnel walking into vehicle area

Vehicle area Ground level

(a)

(b)

Figure 9.4 (a) Typical warehouse vehicle loading/unloading area with separate pedestrian access; (b) barriers to prevent collision with tank surrounds/bunds.

➤ the use of awareness measures, such as training and information in the form of signs or distinctive colouring ➤ the use of appropriate personal protective equipment, in some cases, as discussed previously.

9.3.6

General preventative measures for pedestrian hazards

Minimizing pedestrian hazards and promoting good work practices requires a mixture of sensible planning, good

134

housekeeping and common sense. A few of the required measures are costly or difﬁcult to introduce and, although they are mainly applicable to slips, trips and falls on the same level and collisions with moving vehicles, they can be adapted to all types of pedestrian hazard. Typical measures include: ➤ develop a safe workplace as early as possible and ensure that suitable ﬂoor surfaces and lighting are selected and vehicle and pedestrian routes are carefully planned. Lighting should not dazzle approaching

Movement of people and vehicles – hazards and control

(a)

Figure 9.5

➤

➤ ➤

➤

➤

➤

(b)

(a) Internal roadway with appropriate markings; (b) unsafe stacks of heavy boxes.

vehicles nor should pedestrians be obscured by stored products. Lighting is very important where there are changes of level or stairways. Any physical hazards, such as low beams, vehicular movements or pedestrian crossings, should be clearly marked. Staircases need particular attention to ensure that they are slip resistant and the edges of the stairs marked to indicate a trip hazard consider pedestrian safety when re-orientating the workplace layout (e.g. the need to reposition lighting and emergency lighting) adopt and mark designated walkways apply good housekeeping principles by keeping all areas, particularly walkways, as tidy as possible and ensure that any spillages are quickly removed ensure that all workers are suitably trained in the correct use of any safety devices (such as machine guarding or personal protective equipment) or cleaning equipment provided by the employer only use cleaning materials and substances that are effective and compatible with the surfaces being cleaned, so that additional slip hazards are not created ensure that a suitable system of maintenance, cleaning, fault reporting and repair are in place and working effectively. Areas that are being cleaned must be fenced and warning signs erected. Care must also be taken with trailing electrical leads used with the cleaning equipment. Records of cleaning, repairs and maintenance should be kept

➤ ensure that all workers are wearing appropriate footwear with the correct type of anti-slip soles suitable for the type of ﬂooring ➤ consider whether there are signiﬁcant pedestrian hazards present in the area when any workplace risk assessments are being undertaken.

9.4 Hazards in vehicle operations Many different kinds of vehicle are used in the workplace, including dumper trucks, heavy goods vehicles, all terrain vehicles and, perhaps the most common, the fork lift truck. Approximately 70 persons are killed annually following vehicle accidents in the workplace. There are also over 1000 major accidents (involving serious fractures, head injuries and amputations) caused by: ➤ ➤ ➤ ➤ ➤

collisions between pedestrians and vehicles people falling from vehicles people being struck by objects falling from vehicles people being struck by an overturning vehicle communication problems between vehicle drivers and employees or members of the public.

A key cause of these accidents is the lack of competent and documented driver training. HSE investigations, for example, have shown that in over 30% of dumper truck accidents on construction sites, the drivers had little experience and no training. Common forms of these accidents

135

Introduction to Health and Safety at Work ➤ roadways too narrow with insufﬁcient safe parking areas ➤ roadways poorly marked out and inappropriate or unfamiliar signs used ➤ too few pedestrian crossing points ➤ the non-separation of pedestrians and vehicles ➤ lack of barriers along roadways ➤ lack of directional and other signs ➤ poor environmental factors, such as lighting, dust and noise ➤ ill-deﬁned speed limits and/or speed limits which are not enforced ➤ poor or no regular maintenance checks ➤ vehicles used by untrained and/or unauthorized personnel ➤ poor training or lack of refresher training. Vehicle operations need to be carefully planned so that the possibility of accidents is minimized.

9.5 Control strategies for safe vehicle operations

Figure 9.6

Industrial counter-balanced lift truck.

include driving into excavations, overturning while driving up steep inclines and runaway vehicles which have been left unattended with the engine running. Risks of injuries to employees and members of the public involving vehicles could arise due to the following occurrences: ➤ ➤ ➤ ➤ ➤ ➤

collision with pedestrians collision with other vehicles overloading of vehicles overturning of vehicles general vehicle movements and parking dangerous occurrences or other emergency incidents (including ﬁre) ➤ access and egress from the buildings and the site. There are several other more general hazardous situations involving pedestrians and vehicles. These include the following: ➤ reversing of vehicles, especially inside buildings ➤ poor road surfaces and/or poorly drained road surfaces

136

Any control strategy involving vehicle operations will involve a risk assessment to ascertain where, on trafﬁc routes, accidents are most likely to happen. It is important that the risk assessment examines both internal and external trafﬁc routes, particularly when goods are loaded and unloaded from lorries. It should also assess whether designated trafﬁc routes are suitable for the purpose and sufﬁcient for the volume of trafﬁc. The following needs to be addressed: ➤ trafﬁc routes, loading and storage areas need to be well designed with enforced speed limits, good visibility and the separation of vehicles and pedestrians whenever reasonably practicable ➤ environmental considerations, such as visibility, road surface conditions, road gradients and changes in road level, must also be taken into account ➤ the use of one-way systems and separate site access gates for vehicles and pedestrians may be required ➤ the safety of members of the public must be considered, particularly where vehicles cross public footpaths ➤ all external roadways must be appropriately marked, particularly where there could be doubt on right of way, and suitable direction and speed limit signs erected along the roadways. While there may well be a difference between internal and external speed limits, it is important that all speed limits are observed ➤ induction training for all new employees must include the location and designation of pedestrian walkways and crossings and the location of areas in the factory

Movement of people and vehicles – hazards and control

Figure 9.7

Separate doors for vehicles and pedestrians.

where pedestrians and fork lift trucks use the same roadways ➤ the identiﬁcation of recognized and prohibited parking areas around the site should also be given during these training sessions.

9.6 The management of vehicle movements The movement of vehicles must be properly managed, as must vehicle maintenance and driver training. The development of an agreed code of practice for drivers, to which all drivers should sign up, and the enforcement of site rules covering all vehicular movements are essential for effective vehicle management. All vehicles should be subject to appropriate regular preventative maintenance programmes with appropriate records kept and all vehicle maintenance procedures properly documented. Consideration must be given to driver protection by ﬁtting driver restraint (seat belts), falling object protective structures (FOPS) and roll-over or tip-over protective structures known as ROPS. (See the summary of the Provision and Use of Work Equipment Regulations in Chapter 17 and Section 11.10 Mobile work equipment.) Many vehicles, such as mobile cranes, require regular inspection by a competent person and test certiﬁcates. Certain vehicle movements, such as reversing, are more hazardous than others and particular safe systems should be set up. The reversing of lorries, for example, must be kept to a minimum (and then restricted to particular areas). Vehicles should be ﬁtted with reversing warning systems as well as being able to give warning of approach. Refuges, where pedestrians can stand to avoid reversing vehicles are a useful safety measure.

Banksmen, who direct reversing vehicles, should also be alert to the possibility of pedestrians crossing in the path of the vehicle. Where there are many vehicle movements, consideration should be given to the provision of high visibility clothing. Fire is often a hazard which is associated with many vehicular activities, such as battery charging and the storage of warehouse pallets. All batteries should be recharged in a separate well-ventilated area. As mentioned earlier, driver training, given by competent people, is essential. Only trained drivers should be allowed to drive vehicles and the training should be relevant to the particular vehicle (e.g. fork lift truck, dumper truck, lorry, etc.). All drivers must receive speciﬁc training and instruction before they are permitted to drive vehicles. They must also be given refresher training at regular intervals. This involves a management system for ensuring driver competence, which must include detailed records of all drivers with appropriate training dates and certiﬁcation in the form of a driving licence or authorization. Competence and its deﬁnition are discussed in Chapter 4. The HSE publications Workplace Transport Safety. Guidance for Employers HSG136, and Managing Vehicle Safety at the Workplace INDG199, provide useful checklists of relevant safety requirements that should be in place when vehicles are used in a workplace.

9.7 Managing occupational road safety 9.7.1

Introduction

This section has been added outside the NEBOSH certiﬁcate because it is an important area of concern recently given more prominence by the UK’s HSE. It has been

137

Introduction to Health and Safety at Work estimated that up to a third of all road trafﬁc accidents involve somebody who is at work at the time. This may account for over 20 fatalities and 250 serious injuries every week. Some employers believe, incorrectly, that if they comply with certain road trafﬁc law requirements, so that company vehicles have a valid MOT certiﬁcate, and drivers hold a valid licence, this is enough to ensure the safety of their employees, and others, when they are on the road. However, health and safety law applies to on-the-road work activities as it does to all work activities, and the risks should be managed effectively within a health and safety management system. These requirements are in addition to the duties employers have under road trafﬁc law, e.g. the Road Trafﬁc Act and Road Vehicle (Construction and Use) Regulations, which are administered by the police and other agencies such as the Vehicle and Operator Services Agency. Health and safety law does not apply to commuting, unless the employee is travelling from their home to a location which is not their usual place of work.

9.7.2

Benefits of managing work-related road safety

The true costs of accidents to organizations are nearly always higher than just the costs of repairs and insurance

Figure 9.8

138

Occupational road risk.

claims. The beneﬁts of managing work-related road safety can be considerable, no matter what the size of the organizations. There will be beneﬁts in the area of: ➤ control: costs, such as wear and tear and fuel, insurance premiums and claims can be better controlled ➤ driver training and vehicle purchase: better informed decisions can be made ➤ lost time: fewer days will be lost due to injury, ill health and work rescheduling ➤ vehicles: fewer will need to be off the road for repair ➤ orders: fewer orders will be missed ➤ key employees: there is likely to be a reduction in driving bans.

9.7.3

Managing occupational road risks

Where work-related road safety is integrated into the arrangements for managing health and safety at work, it can be managed effectively. The main areas to be addressed are, policy, responsibility, organization, systems and monitoring. Employees should be encouraged to report all work-related road incidents and be assured that punitive action will not be taken against them? The risk assessment should: ➤ consider the use, for example, of air or rail transport as a partial alternative to driving

Movement of people and vehicles – hazards and control

Figure 9.9

Must have a licence valid for vehicle.

➤ attempt to avoid situations where employees feel under pressure ➤ make sure that maintenance work is organized to reduce the risk of vehicle failure ➤ insist that drivers and passengers are adequately protected in the event of an incident. Crash helmets and protective clothing for those who ride motorcycles and other two-wheeled vehicles should be of the appropriate colour and standard. ➤ ensure that company policy covers the important aspects of the Highway Code.

➤ Is the driving licence checked for validity on recruitment and periodically thereafter? ➤ When the driver is at work, is he or she aware of company policy on work-related road safety? ➤ Are written instructions and guidance available? ➤ Has the company speciﬁed and monitored the standards of skill and expertise required for the circumstances for the job?

Training Are drivers properly trained?

9.7.4

Evaluating the risks

The following considerations can be used to check on work-related road safety management

The driver Competency ➤ Is the driver competent, experienced and capable of doing the work safely? ➤ His or her licence valid for the type of vehicle to be driven? ➤ Is the vehicle suitable for the task or is it restricted by the driver’s licence? ➤ Does recruitment procedure include appropriate pre-appointment checks?

➤ Do drivers need additional training to carry out their duties safely? ➤ Does the company provide induction training for drivers? ➤ Are those drivers whose work exposes them to the highest risk given priority in training? ➤ Do drivers need to know how to carry out routine safety checks such as those on lights, tyres and wheel ﬁxings? ➤ Do drivers know how to adjust safety equipment correctly, for example seat belts and head restraints? ➤ Is the headrest 3.8 cm (1.5 inches) behind the driver’s head? ➤ Is the front of the seat higher than the back and are the legs 45º to the ﬂoor?

139

Introduction to Health and Safety at Work ➤ Is the steering wheel adjustable and set low to avoid shoulder stress? ➤ Are drivers able to use anti-lock brakes (ABS) properly? ➤ Do drivers have the expertise to ensure safe load distribution? ➤ If the vehicle breaks down, do drivers know what to do to ensure their own safety? ➤ Is there a handbook for drivers? ➤ Are drivers aware of the dangers of fatigue? ➤ Do drivers know the height of their vehicle, both laden and empty?

Fitness and health ➤ The driver’s level of health and ﬁtness should be sufﬁcient for safe driving? ➤ Drivers of HGV’s must have the appropriate medical certiﬁcate. ➤ Drivers who are most at risk, should also undergo regular medicals. Staff should not drive, or undertake other duties, while taking a course of medicine that might impair their judgement. ➤ All drivers should have regular (every 2 years) eye sight tests. Recent research has shown many drivers have poor eye sight which affects the standard of their driving.

The vehicle Suitability All vehicles should be ﬁt for the purpose for which they are used. When purchasing new or replacement vehicles, the management should look for vehicles that are most suitable for driving and public health and safety. The ﬂeet should be suitable for the job in hand. Where privately owned vehicles are used for work they should be insured for business use and have an appropriate MOT certiﬁcate (over 3 years old in the UK).

Condition and Safety Equipment Are vehicles maintained in a safe and ﬁt condition? There will need to be: ➤ Maintenance arrangements to acceptable standards ➤ basic safety checks for drivers ➤ a method of ensuring that the vehicle does not exceed its maximum load weight ➤ reliable methods to secure goods and equipment in transit ➤ checks to make sure that safety equipment is in good working order ➤ Checks on seatbelts and head restraints. Are they ﬁtted correctly and functioning properly? ➤ Drivers need to know what action to take if they consider their vehicle is unsafe.

140

Ergonomic considerations The health of the drivers, and possibly also their safety, may be put at risk from through an inappropriate seating position or driving posture. Ergonomic considerations should therefore be considered before purchasing or leasing new vehicles. Information may need to be provided to drivers about good posture and, where appropriate, on how to set their seat correctly?

The load For any lorry driving, most of the topics covered in this section are relevant. However, the load being carried is an additional issue. If the load is hazardous, emergency procedures (and possibly equipment) must be in place and the driver trained in those procedures. The load should be stacked safely in the lorry so that it cannot move during the journey. There must also be satisfactory arrangements for handling the load at either end of the journey.

The journey Routes Route planning is crucial. Safe routes should be chosen which are appropriate for the type of vehicle undertaking the journey wherever practicable. Motorways are the safest roads. Minor roads are suitable for cars, but they are less safe and could present difﬁculties for larger vehicles. Overhead restrictions for example bridges, tunnels and other hazards such as level crossings, may present dangers for long and/or high vehicles so route planning should take particular account of these.

Scheduling There are danger periods during the day and night when people are most likely, on average, to feel sleepy. These are between 2 am and 6 am and between 2 pm and 4 pm. Schedules need to take sufﬁcient account of these periods. Where tachographs are carried, they should be checked regularly to make sure that drivers are not putting themselves and others at risk by driving for long periods without a break. Periods of peak trafﬁc ﬂow should be avoided if possible and new drivers should be given extra support while training.

Time Has enough time been allowed to complete the driving job safely? A realistic schedule would take into account the type and condition of the road and allow the driver rest breaks. A non-vocational driver should not be expected to drive and work for longer than a professional driver. The recommendation of the Highway Code is for a 15 minute break every two hours. ➤ Are drivers put under pressure by the policy of the company? Are they encouraged to take unnecessary

Movement of people and vehicles – hazards and control risks, for example exceeding safe speeds because of agreed arrival times? ➤ Is it possible for the driver to make an overnight stay? This may be preferable to having to complete a long road journey at the end of the working day? ➤ Are staff aware that working irregular hours can add to the dangers of driving? They need to be advised of the dangers of driving home from work when they are excessively tired. In such circumstances they may wish to consider an alternative, such as a taxi.

Distance Managers need to satisfy themselves that drivers will not be put at risk from fatigue caused by driving excessive distances without appropriate breaks. Combining driving with other methods of transport may make it possible for long road journeys to be eliminated or reduced. Employees should not be asked to work an exceptionally long day.

Weather conditions When planning journeys, sufﬁcient consideration will need to be given to adverse weather conditions, such as snow, ice, heavy rain and high winds. Routes should be rescheduled and journey times adapted to take adverse weather conditions into consideration. Where poor weather conditions are likely to be encountered, vehicles should be properly equipped to operate, with, for example, anti-lock brakes. Where there are ways of reducing risk, for example when driving a high sided vehicle in strong winds with a light load, drivers should have the expertise to deal with the situation. In addition, they should not feel pressurized to complete journeys where weather conditions are exceptionally difﬁcult and this should be made clear by management.

9.7.5

➤ Plan the journey in advance to avoid, where possible, dangerous roads or trafﬁc delays ➤ Use headlights in poor weather conditions and fog lights in foggy conditions ➤ Use hazard warning lights if an accident or severe trafﬁc congestion is approached (particularly on motorways) ➤ All speed limits must be observed but speeds should always be safe for the conditions encountered ➤ Drivers must not drive continuously for more than 2 hours without a break of at least 15 minutes ➤ Mobile phones, including hands-free equipment, must not be used whilst driving. They must be turned off during the journey and only used during the rest periods or when the vehicle is safely parked and the handbrake on ➤ No alcohol must be consumed during the day of the journey until the journey is completed. Only minimal amounts of alcohol should be consumed on the day before a journey is to be made ➤ No recreational drugs should be taken on the day of a journey. Some prescribed and over the counter drugs and medicines can also affect driver awareness and speed of reaction. Always check with a doctor or pharmacist to ensure that it is safe to drive.

9.7.6

Further information

The Highway Code The Stationery Ofﬁce 2001 ISBN 0 11 552290 5 Can also be viewed on www.highwaycode. gov.uk Managing occupational road risk Royal Society for the Prevention of Accidents available from Edgbaston Park, 353 Bristol Road, Birmingham B5 7ST Tel: 0121 248 2000 Driving at work managing work-related road safety HSE INDG382 ISBN 0 -7176 2824 8

Typical health and safety rules for drivers of cars on company business

The following example shows typical rules that have been prepared for use of car drivers. Approximately 25% of all road accidents are work related accidents involving people who are using the vehicle on company business. Drivers are expected to understand and comply with the relevant requirements of the current edition of the Highway Code. The following rules have been produced to reduce accidents at work. Any breach of these rules will be a disciplinary offence. ➤ All drivers must have a current and valid driving licence ➤ All vehicles must carry comprehensive insurance for use at work

9.8 Practice NEBOSH questions for Chapter 9 1. (a) Identify the types of hazard that may cause slips or trips at work (b) Outline how slip and trip hazards in the workplace might be controlled. 2. A cleaner is required to polish ﬂoors using a rotary ﬂoor polisher. (i) Identify the hazards that might be associated with this operation (ii) Outline suitable control measures that might be used minimize the risk.

141

Introduction to Health and Safety at Work 3. Outline the precautionary measures that may be needed to prevent slips and trip hazards in an engineering factory. 4. Outline the measures that may be needed to reduce the risk of slip and trip accidents in a large supermarket. 5. List EIGHT design features and/or safe practices intended to reduce the risk of accidents on staircases used as internal pedestrian routes within work premises. 6. (a) Give FOUR reasons why accidents may occur on stairs (b) Outline ways in which accidents on stairs may be prevented. 7. Outline the factors that may increase the risk of injury to pedestrians who need to walk through a warehouse. 8. Describe the physical features of trafﬁc routes within a workplace designed to ensure the safe movement of vehicles.

142

9. Outline the factors that should be taken into account when planning trafﬁc routes for internal transport. 10. Outline measures to be taken to prevent accidents when pedestrians are required to work in vehicle manoeuvring areas. 11. Outline the means by which the risk of accidents from reversing vehicles within a workplace can be reduced. 12. The warehouse of a ceramic tile manufacturer is to be developed to increase its storage capacity and to enable the use of internal transport to transfer the goods to and from the loading bays. (a) Outline the design features of the trafﬁc routes that should be addressed in order to minimize the risk of fork lift truck related accidents. (b) Describe additional measures that need to be taken to protect pedestrians from the risk of being struck by a fork lift truck in the warehouse. 13. Outline the factors to consider when assessing the risks to a long distance delivery driver.

Manual and mechanical handling hazards and control

10.1 Introduction Until a few years ago, accidents caused by the manual handling of loads were the largest single cause of over three-day accidents reported to the HSE. The Manual Handling Operations Regulations recognized this fact and helped to reduce the number of these accidents. However, accidents due to poor manual handling technique still accounts for over 25% of all reported accidents and in some occupational sectors, such as the health service, the ﬁgure rises above 50%. An understanding of the factors causing some of these accidents is essential if they are to be further reduced. Mechanical handling methods should always be used whenever possible, but they are not without their hazards, many of which are outlined in Chapter 9 and later in Chapter 10.

10

Much mechanical handling involves the use of lifting equipment, such as cranes and lifts which present speciﬁc hazards to both the users and bystanders. The risks from these hazards are reduced by thorough examinations and inspections as required by the Lifting Operations and Lifting Equipment Regulations (LOLER).

10.2 Manual handling hazards and injuries The term ‘manual handling’ is deﬁned as the movement of a load by human effort alone. This effort may be applied directly or indirectly using a rope or a lever. Manual handling may involve the transportation of the load or the direct support of the load including pushing, pulling, carrying, moving using bodily force and, of course, straightforward lifting. Back injuries due to the lifting of heavy loads is very common and several million working days are lost each year as a result of such injuries. Typical hazards of manual handling include: ➤ lifting a load which is too heavy or too cumbersome resulting in back injury ➤ poor posture during lifting or poor lifting technique resulting in back injury ➤ dropping a load, resulting in foot injury ➤ lifting sharp-edged or hot loads resulting in hand injuries.

10.2.1 Figure 10.1 Handling goods onto a truck in a typical docking bay.

Injuries caused by manual handling

Manual handling operations can cause a wide range of acute and chronic injuries to workers. Acute injuries

143

Introduction to Health and Safety at Work

Back 45% Rest of torso 8% Arm 13% Hand 6% Fingers and thumb 16%

Lower limb 9%

Figure 10.2 hazards.

Manual handling – there are many potential

normally lead to sickness leave from work and a period of rest during which time the damage heals. Chronic injuries build up over a long period of time and are usually irreversible producing illnesses such as arthritic and spinal disorders. There is considerable evidence to suggest that modern lifestyles, such as a lack of exercise and regular physical effort, have contributed to the longterm serious effects of these injuries. The most common injuries associated with poor manual handling techniques are all musculoskeletal in nature and are: ➤ muscular sprains and strains – caused when a muscular tissue (or ligament or tendon) is stretched beyond its normal capability leading to a weakening, bruising and painful inﬂammation of the area affected. Such injuries normally occur in the back or in the arms and wrists ➤ back injuries – include injuries to the discs situated between the spinal vertebrae (i.e. bones) and can lead to a very painful prolapsed disc lesion (commonly known as a slipped disc). This type of injury can lead to other conditions known as lumbago and sciatica (where pain travels down the leg) ➤ trapped nerve – usually occurring in the back as a result of another injury but aggravated by manual handling ➤ hernia – this is a rupture of the body cavity wall in the lower abdomen causing a protrusion of part of the intestine. This condition eventually requires surgery to repair the damage ➤ cuts, bruising and abrasions – caused by handling loads with unprotected sharp corners or edges ➤ fractures – normally of the feet due to the dropping of a load. Fractures of the hand also occur but are less common

144

Figure 10.3 accidents.

Main injury sites caused by manual handling

➤ work-related upper limb disorders (WRULDs) – cover a wide range of musculoskeletal disorders which are discussed in detail in Chapter 15 ➤ rheumatism – this is a chronic disorder involving severe pain in the joints. It has many causes, one of which is believed to be the muscular strains induced by poor manual handling lifting technique. The sites on the body of injuries caused by manual handling accidents are shown in Figure 10.3. In general, pulling a load is much easier for the body than pushing one. If a load can only be pushed, then pushing backwards using the back is less stressful on body muscles. Lifting a load from a surface at waist level is easier than lifting from ﬂoor level and most injuries during lifting are caused by lifting and twisting at the same time. If a load has to be carried, it is easier to carry it at waist level and close to the body trunk. A ﬁrm grip is essential when moving any type of load.

10.3 Manual handling risk assessments 10.3.1

Hierarchy of measures for manual handling operations

With the introduction of the Manual Handling Operations Regulations, the emphasis during the assessment of lifting operations changed from a simple reliance on safe lifting techniques to an analysis, using risk assessment, of the need for manual handling. The Regulations

Manual and mechanical handling hazards and control established a clear hierarchy of measures to be taken when an employer is confronted with a manual handling operation: ➤ avoid manual handling operations so far as is reasonably practicable by either redesigning the task to avoid moving the load or by automating or mechanizing the operations ➤ if manual handling cannot be avoided, then a suitable and sufﬁcient risk assessment should be made ➤ reduce the risk of injury from those operations so far as is reasonably practicable, either by the use of mechanical handling or making improvements to the task, the load and the working environment. The guidance given to the Manual Handling Operations Regulations (available in the HSE Legal series – L23) is a very useful document. It gives very helpful advice on manual handling assessments and manual handling training. The advice is applicable to all occupational sectors. Appendix 10.1 gives an example of manual handling assessment forms.

10.3.2

Manual handling assessments

The Regulations specify four main factors which must be taken into account during the assessment. These are the task, the load, the working environment and the capability of the individual who is expected to do the lifting. The task should be analysed in detail so that all aspects of manual handling are covered including the use of mechanical assistance. The number of people involved and the cost of the task should also be considered. Some or all of the following questions are relevant to most manual handling tasks: ➤ is the load held or manipulated at a distance from the trunk? The further from the trunk, the more difﬁcult it is to control the load and the stress imposed on the back is greater ➤ is a satisfactory body posture being adopted? Feet should be ﬁrmly on the ground and slightly apart and there should be no stooping or twisting of the trunk. It should not be necessary to reach upwards since this will place additional stresses on the arms, back and shoulders. The effect of these risk factors is signiﬁcantly increased if several are present while the task is being performed ➤ are there excessive distances to carry or lift the load? Over distances greater than 10 m, the physical demands of carrying the load will dominate the operation. The frequency of lifting, and the vertical and horizontal distances the load needs to be carried (particularly if it has to be lifted from the ground

➤

➤ ➤

➤

➤

➤

➤

and/or placed on a high shelf) are very important considerations is there excessive pulling and pushing of the load? The state of ﬂoor surfaces and the footwear of the individual should be noted so that slips and trips may be avoided is there a risk of a sudden movement of the load? The load may be restricted or jammed in some way is frequent or prolonged physical effort required? Frequent and prolonged tasks can lead to fatigue and a greater risk of injury are there sufﬁcient rest or recovery periods? Breaks and/or the changing of tasks enables the body to recover more easily from strenuous activity is there an imposed rate of work on the task? This is a particular problem with some automated production lines and can be addressed by spells on other operations away from the line are the loads being handled while the individual is seated? In these cases, the legs are not used during the lifting processes and stress is placed on the arms and back does the handling involve two or more people? The handling capability of an individual reduces when he becomes a member of a team (e.g. for a three person team, the capability is half the sum of the individual capabilities). Visibility, obstructions and the roughness of the ground must all be considered when team handling takes place.

The load must be carefully considered during the assessment and the following questions asked: ➤ is the load too heavy? The maximum load that an individual can lift will depend on the capability of the individual and the position of the load relative to the body. There is therefore no safe load, but Figure 10.4 is reproduced from the HSE guidance, which does give some advice on loading levels. It does not recommend that loads in excess of 25 kg should be lifted or carried by a man (and this is only permissible when the load is at the level of and adjacent to the thighs). For women, the guideline ﬁgures should be reduced by about one third ➤ is the load too bulky or unwieldy? In general, if any dimension of the load exceeds 0.75 m (2 ft), its handling is likely to pose a risk of injury. Visibility around the load is important. It may hit obstructions or become unstable in windy conditions. The position of the centre of gravity is very important for stable lifting – it should be as close to the body as possible ➤ is the load difﬁcult to grasp? Grip difﬁculties will be caused by slippery surfaces, rounded corners or a lack of foot room

145

Introduction to Health and Safety at Work

Figure 10.4

HSE guidance for manual lifting – recommended weights.

➤ are the contents of the load likely to shift? This is a particular problem when the load is a container full of smaller items, such as a sack full of nuts and bolts. The movement of people (in a nursing home) or animals (in a veterinary surgery) are loads which fall into this category ➤ is the load sharp, hot or cold? Personal protective equipment may be required. The working environment in which the manual handling operation is to take place, must be considered during the assessment. The following areas will need to be assessed: ➤ any space constraints which might inhibit good posture. Such constraints include lack of headroom, narrow walkways and items of furniture ➤ slippery, uneven or unstable ﬂoors ➤ variations in levels of ﬂoors or work surfaces, possibly requiring the use of ladders ➤ extremes of temperature and humidity. These effects are discussed in detail in Chapter 15 ➤ ventilation problems or gusts of wind ➤ poor lighting conditions. Finally, the capability of the individual to lift or carry the load must be assessed. The following questions will need to be asked: ➤ does the task require unusual characteristics of the individual (e.g. strength or height)? It is important to remember that the strength and general manual handling ability depends on age, gender, state of health and ﬁtness ➤ are employees who might reasonably be considered to be pregnant or to have a health problem, put at

146

risk by the task? Particular care should be taken to protect pregnant women or those who have recently given birth from handling loads. Allowance should also be given to any employee who has a health problem, which could be exacerbated by manual handling. The assessment must be reviewed if there is reason to suspect that it is no longer valid or there has been a signiﬁcant change to the manual handling operations to which it relates.

10.3.3

Reducing the risk of injury

This involves the introduction of control measures resulting from the manual handling risk assessment. The guidance to the Regulations (L23) and the HSE publication Manual Handling – solutions you can handle (HSG 115) contain many ideas to reduce the risk of injury from manual handling operations. An ergonomic approach, discussed in detail in Chapter 15, is generally required to design and develop the manual handling operation as a whole. The control measures can be grouped under ﬁve headings. However, the ﬁrst consideration, when it is reasonably practicable, is mechanical assistance. Mechanical assistance involves the use of mechanical aids to assist the manual handling operation such as hand-powered hydraulic hoists, specially adapted trolleys, hoists for lifting patients and roller conveyors. The task can be improved by changing the layout of the workstation by, for example, storing frequently used loads at waist level. The removal of obstacles and the use of a better lifting technique that relies on the leg rather than back muscles should be encouraged. When pushing, the hands should be positioned correctly. The work routine should also be examined to see whether job

Manual and mechanical handling hazards and control

Figure 10.6

Figure 10.5

Mechanical aids to lift patients in hospital.

rotation is being used as effectively as it could be. Special attention should be paid to seated manual handlers to ensure that loads are not lifted from the ﬂoor while they are seated. Employees should be encouraged to seek help if a difﬁcult load is to be moved so that a team of people can move the load. Adequate and suitable personal protective equipment should be provided where there is a risk of loss of grip or injury. Care must be taken to ensure that the clothing does not become a hazard in itself (e.g. the snagging of fasteners and pockets). The load should be examined to see whether it could be made lighter, smaller or easier to grasp or manage. This could be achieved by splitting the load, the positioning of handholds or a sling, or ensuring that the centre of gravity is brought closer to the handler’s body. Attempts should be made to make the load more stable and any surface hazards, such as slippery deposits or sharp edges, should be removed. It is very important to ensure that any improvements do not, inadvertently, lead to the creation of additional hazards. The working environment can be improved in many ways. Space constraints should be removed or reduced. Floors should be regularly cleaned and repaired when damaged. Adequate lighting is essential and working at more than one level should be minimized so that hazardous ladder work is avoided. Attention should be given to the need for suitable temperatures and ventilation in the working area. The capability of the individual is the ﬁfth area where control measures can be applied to reduce the

A pallet truck.

risk of injury. The state of health of the employee and his/her medical record will provide the ﬁrst indication as to whether the individual is capable of undertaking the task. A period of sick leave or a change of job can make an individual vulnerable to manual handling injury. The Regulations require that the employee be given information and training. The information includes the provision, where it is reasonably practicable to do so, of precise information on the weight of each load and the heaviest side of any load whose centre of gravity is not centrally positioned. In a more detailed risk assessment, other factors will need to be considered such as the effect of personal protective equipment and psychosocial factors in the work organization. The following points may need to be assessed: ➤ Does protective clothing hinder movement or posture? ➤ Is the correct personal protective equipment being worn? ➤ Is proper consideration given to the planning and scheduling of rest breaks? ➤ Is there good communication between managers and employees during risk assessment or workstation design? ➤ Is there a mechanism in place to deal with sudden changes in the volume of workload? ➤ Have employees been given sufﬁcient training and information? ➤ Has the worker any learning disabilities and, if so, has this been taken into account in the assessment? HSE has developed a Manual Handling Assessment Chart (MAC) to help with the assessment of common

147

Introduction to Health and Safety at Work

1. Check suitable clothing and assess load. Heaviest side to body. 2. Place feet apart – bend knees. 1

2

3

4

3. Firm grip – close to body slight bending of back, hips and knees at start 4. Life smoothly to knee level and then waist level. No further bending of back. 5. With clear visibility move forward without twisting. Keep load close to the waist. Turn by moving feet. Keep head up do not look at load.

5

Figure 10.7

6. Set load down at waist level or to knee level and then floor.

6

The main elements of a good lifting technique.

risks associated with lifting, carrying and handling. The MAC is available on the HSE website. The training requirements are given in the next section.

10.4 Safety in the use of lifting and moving equipment

10.3.4

An amendment to the Lifting Operations and Lifting Equipment Regulations included the positioning and installation of lifting equipment and the organization of lifting operations.

Manual handling training

Training alone will not reduce manual handling injuries – there still need to be safe systems of work in place and the full implementation of the control measures highlighted in the manual handling assessment. The following topics should be addressed in a manual handling training session: ➤ types of injuries associated with manual handling activities ➤ the ﬁndings of the manual handling assessment ➤ the recognition of potentially hazardous manual handling operations ➤ the correct use of mechanical handling aids ➤ the correct use of personal protective equipment ➤ features of the working environment which aid safety in manual handling operations ➤ good housekeeping issues ➤ factors which affect the capability of the individual ➤ good lifting or manual handling technique as shown in Figure 10.7 Finally, it needs to be stressed that if injuries involving manual handling operations are to be avoided, planning, control and effective supervision are essential.

148

10.4.1

Positioning and installation of lifting equipment

Lifting equipment must be positioned and installed so as to reduce the risks, so far as is reasonably practicable, from: ➤ equipment or a load striking another person ➤ a load drifting, falling freely or being released unintentionally and it is otherwise safe. Lifting equipment should be positioned and installed to minimize the need to lift loads over people and to prevent crushing in extreme positions. It should be designed to stop safely in the event of a power failure and not release its load. Lifting equipment, which follows a ﬁxed path, should be enclosed with suitable and substantial interlocked gates and any necessary protection in the event of power failure.

Manual and mechanical handling hazards and control 10.4.2

The organization of lifting operations

Every lifting operation, that is lifting or lowering of a load, shall be: ➤ properly planned by a competent person ➤ appropriately supervised ➤ carried out in a safe manner. The person planning the operation should have adequate practical and theoretical knowledge and experience of planning lifting operations. The plan needs to address the risks identiﬁed by the risk assessment and identify the resources, the procedures and the responsibilities required so that any lifting operation is carried out safely. For routine simple lifts, a plan will normally be the responsibility of the people using the lifting equipment. For complex lifting operations, for example, where two cranes are used to lift one load, a written plan may need to be produced each time. The planning should include: the need to avoid suspending loads over occupied areas, visibility, the attaching/detaching and securing of loads, the environment, the location, the possibility of overturning, the proximity to other objects, any lifting of people and the pre-use checks required for the equipment.

10.4.3 Summary of the requirements for lifting operations There are four general requirements for all lifting operations: ➤ strong, stable and suitable lifting equipment ➤ the equipment should be positioned and installed correctly ➤ the equipment should be visibly marked with the safe working load ➤ lifting operations must be planned, supervised and performed in a safe manner by competent people.

10.5 Types of mechanical handling and lifting equipment There are four elements to mechanical handling, each of which can present hazards. These are handling equipment, the load, the workplace and the employees involved. The mechanical handling equipment must be capable of lifting and/or moving the load. It must be fault-free, well maintained and inspected on a regular basis. The hazards related to such equipment include collisions between people and the equipment and personal injury from being trapped in moving parts of the equipment (such as belt and screw conveyors).

The load should be prepared for transportation in such a way as to minimize the possibility of accidents. The hazards will be related to the nature of the load (e.g. substances which are ﬂammable or hazardous to health) or the security and stability of the load (e.g. collapse of bales or incorrectly stacked pallets). The workplace should be designed so that, whenever possible, workers and the load are kept apart. If, for example, an overhead crane is to be used, then people should be segregated away or barred from the path of the load. The employees and others and any other people who are to use the equipment must be properly trained and competent in its safe use.

10.5.1

Conveyors and elevators

Conveyors transport loads along a given level which may not be completely horizontal, whereas elevators move loads from one level or ﬂoor to another. There are three common forms of conveyor – belt, roller and screw conveyors. The most common hazards and preventative measures are: ➤ the in-running nip, where a hand is trapped between the rotating rollers and the belt. Protection from this hazard can be provided by nip guards and trip devices ➤ entanglement with the power drive requiring the ﬁtting of ﬁxed guards and the restriction of loose clothing which could become caught in the drive ➤ loads falling from the conveyor. This can be avoided by edge guards and barriers ➤ impact against overhead systems. Protection against this hazard may be given by the use of bump caps, warning signs and restricted access ➤ contact hazards prevented by the removal of sharp edges, conveyor edge protection and restricted access ➤ manual handling hazards ➤ noise and vibration hazards. Screw conveyors, often used to move very viscous substances, must be provided with either ﬁxed guards or covers to prevent accidental access. People should be prohibited from riding on belt conveyors and emergency trip wires or stop buttons must be ﬁtted and be operational at all times. Elevators are used to transport goods between ﬂoors, such as the transportation of building bricks to upper storeys during the construction of a building or the transportation of grain sacks into the loft of a barn. Guards should be ﬁtted at either end of the elevator and around the power drive. The most common hazard is injury due to loads falling from elevators. There are also

149

Introduction to Health and Safety at Work

(b)

(a)

(c)

Figure 10.8 Conveyor systems: (a) Roller conveyor (these may have powered and free running rollers); (b) An overhead conveyor handling wheels. Other designs of overhead conveyor are useful for transferring components and garments between workstations, in for example manufacture of machines or clothing: (c) A slat conveyor in use in the food industry.

potential manual handling problems at both the feed and discharge ends of the elevator.

10.5.2

Fork lift trucks

The most common form of mobile handling equipment is the fork lift truck (Figures 9.6 and 10.10). It comes from the group of vehicles, known as lift trucks, and can be used in factories, on construction sites and on farms. The term fork lift truck is normally applied to the counterbalanced lift truck, where the load on the forks is counterbalanced by the weight of the vehicle over the rear wheels. The reach truck is designed to operate in narrower aisles in warehouses and enables the load to be retracted within the wheelbase. The very narrow aisle (VNA) truck does not turn within the aisle to deposit or

150

retrieve a load. It is often guided by guides or rails on the ﬂoor. Other forms of lift truck include the pallet truck and the pallet stacker truck, both of which may be pedestrian or rider controlled. There are many hazards associated with the use of fork lift trucks. These include: ➤ overturning – manoeuvring at too high a speed (particularly cornering), wheels hitting an obstruction such as a kerb, sudden braking, poor tyre condition leading to skidding, driving forwards down a ramp, movement of the load, insecure, excessive or uneven loading, incorrect tilt or driving along a ramp ➤ overloading – exceeding the rated capacity of the machine

Manual and mechanical handling hazards and control

Figure 10.9

A brick elevator.

➤ collisions – particularly with warehouse racking which can lead to a collapse of the whole racking system ➤ silent operation of the electrically powered fork lift truck – can make pedestrians unaware of its presence ➤ uneven road surface – can cause the vehicle to overturn and/or cause musculoskeletal problems for the driver ➤ overhead obstructions – a particular problem for inexperienced drivers ➤ loss of load – shrink wrapping or sheeting will reduce this hazard ➤ inadequate maintenance leading to mechanical failure ➤ use as a work platform ➤ speeding – strict enforcement of speed limits is essential ➤ poor vision around the load ➤ pedestrians – particularly when pedestrians and vehicles use the same roadways. Warning signs, indicating the presence of fork lift trucks, should be posted at regular intervals ➤ dangerous stacking or de-stacking technique – this can destabilize a complete racking column ➤ carrying passengers – this should be a disciplinary offence ➤ battery charging – presents an explosion and ﬁre risk ➤ ﬁre – often caused by poor maintenance resulting in fuel leakages or engine/motor burn-out, or through using a fork lift truck in areas where ﬂammable liquids or gases are used and stored ➤ lack of driver training. If fork lift trucks are to be used outside, visibility and lighting, weather conditions and the movement of other vehicles become additional hazards. There are also the following physical hazards: ➤ noise – caused by poor silencing of the power unit ➤ exhaust fumes – should only be a problem when the maintenance regime is poor ➤ vibrations – often caused by a rough road surface or wide expansion joints. Badly inﬂated tyres will exacerbate this problem ➤ manual handling – resulting from manoeuvring the load by hand or lifting batteries or gas cylinders ➤ ergonomic – musculoskeletal injuries caused by soft tyres and/or undulating road surface or holes or cracks in the road surface (e.g. expansion joints). Regular and documented maintenance by competent mechanics is essential. However, the driver should undertake the following checks at the beginning of each shift:

Figure 10.10 Reach truck designed so that the load retracts within the wheelbase to save space.

➤ condition of tyres and correct tyre pressures ➤ effectiveness of all brakes ➤ audible reversing horn and light working properly

151

Introduction to Health and Safety at Work ➤ lights, if ﬁtted, working correctly ➤ mirrors, if ﬁtted, in good working order and properly set ➤ secure and properly adjusted seat ➤ correct ﬂuid levels, when appropriate ➤ fully charged batteries, when appropriate ➤ correct working of all lifting and tilting systems. A more detailed inspection should be undertaken by a competent person within the organization on a weekly basis to include the mast and the steering gear. Driver training is essential and should be given by a competent trainer. The training session must include the site rules covering items such as the fork lift truck driver code of practice for the organization, speed limits, stacking procedures and reversing rules. Refresher training should be provided at regular intervals and a detailed record kept of all training received. Table 10.1 illustrates some key requirements of fork lift truck drivers and the points listed should be included in most codes of practice. Finally, care must be taken with the selection of drivers, including relevant health checks and previous experience. Drivers should be at least 18 years of age

Table 10.1

Safe driving of lift trucks

Drivers must: • drive at a suitable speed to suit road conditions and visibility • use the horn when necessary (at blind corners and doorways) • always be aware of pedestrians and other vehicles • take special care when reversing (do not rely on mirrors) • take special care when handling loads which restrict visibility • travel with the forks (or other equipment ﬁtted to the mast) lowered • use the prescribed lanes • obey the speed limits • take special care on wet and uneven surfaces • use the handbrake, tilt and other controls correctly • take special care on ramps • always leave the truck in a state which is safe and discourages unauthorized use (brake on, motor off, forks down, key out) Drivers must not: • operate in conditions in which it is not possible to drive and handle loads safely (e.g. partially blocked aisles) • travel with the forks raised • use the forks to raise or lower persons unless a purposebuilt working cage is used • carry passengers • park in an unsafe place (e.g. obstructing emergency exits) • turn round on ramps • drive into areas where the truck would cause a hazard (ﬂammable substance store) • allow unauthorized use.

152

and their ﬁtness to drive should be reassessed at threeyearly intervals.

10.5.3

Other forms of lifting equipment

The other types of lifting equipment to be considered are cranes (mobile overhead and jib), lifts and hoists and lifting tackle. Cranes may be either a jib crane or an overhead gantry travelling crane. The safety requirements are similar for each type. All cranes need to be properly designed, constructed, installed and maintained. They must also be operated in accordance with a safe system of work. They should only be driven by authorized persons who are ﬁt and trained. Each crane is issued with a certiﬁcate by its manufacturer giving details of the safe working load (SWL). The safe working load must never be exceeded and should be marked on the crane structure. If the safe working load is variable, as with a jib crane (the safe working load decreases as the operating radius increases), a safe working load indicator should be ﬁtted. Care should be taken to avoid sudden shock loading since this will impose very high stresses to the crane structure. It is also very important that the load is properly shackled and all eyebolts tightened. Safe slinging should be included in any training programme. All controls should be clearly marked and be of the ‘hold to run’ type. Large cranes, which incorporate a driving cab, often work in conjunction with a banksman who will direct the lifting operation from the ground. It is important that banksmen are trained so that they understand recognized crane signals. The basic principles for the safe operation of cranes are as follows. For all cranes, the driver must: ➤ undertake a brief inspection of the crane and associated lifting tackle each time before it is used ➤ ensure that loads are not left suspended when the crane is not in use ➤ before a lift is made, ensure that nobody can be struck by the crane or the load ➤ ensure that loads are never carried over people ➤ ensure good visibility and communications ➤ lift loads vertically – cranes must not be used to drag a load ➤ travel with the load as close to the ground as possible ➤ switch off power to the crane when it is left unattended. For mobile jib cranes, the following points should be considered: ➤ each lift must be properly planned, with the maximum load and radius of operation known

Manual and mechanical handling hazards and control ➤ overhead obstructions or hazards must be identiﬁed, it may be necessary to protect the crane from overhead power lines by using goal posts and bunting to mark the safe headroom ➤ the ground on which the crane is to stand should be assessed for its load-bearing capacity ➤ if ﬁtted, outriggers should be used. The principal reasons for crane failure, including loss of load, are: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

overloading poor slinging of load insecure or unbalanced load loss of load overturning collision with another structure or overhead power lines foundation failure structural failure of the crane operator error lack of maintenance and/or regular inspections.

During lifting operations using cranes, it must be ensured that: ➤ the driver has good visibility ➤ there are no pedestrians below the load by using barriers, if necessary ➤ an audible warning is given prior to the lifting operation.

Figure 10.11

If lifting takes place in windy conditions, tag lines may need to be attached to the load to control its movement. A lift or hoist incorporates a platform or cage and is restricted in its movement by guides. Hoists are generally used in industrial settings (e.g. construction sites and garages), whereas lifts are normally used inside buildings. Lifts and hoists may be designed to carry passengers and/or goods alone. They should be of sound mechanical construction and have interlocking doors or gates, which must be completely closed before the lift or hoist moves. Passenger carrying lifts must be ﬁtted with an automatic braking system to prevent overrunning, at least two suspension ropes, each capable alone of supporting the maximum working load and a safety device which could support the lift in the event of suspension rope failure. Maintenance procedures must be rigorous, recorded and only undertaken by competent persons. It is very important that a safe system of work is employed during maintenance operations to protect others, such as members of the public, from falling down the lift shaft and other hazards. Other items of lifting tackle, usually used with cranes, include chain slings and hooks, wire and ﬁbre rope slings, eyebolts and shackles. Special care should be taken when slings are used to ensure that the load is properly secured and balanced. Lifting hooks should be checked for signs of wear and any distortion of the hook. Shackles and eyebolts must be correctly tightened. Slings should always be checked for any damage before they are used and only competent people should use

Manoeuvring a yacht using a large overhead travelling gantry and slings in a marina.

153

Introduction to Health and Safety at Work 10.6 Requirements for the statutory examination of lifting equipment

Figure 10.12

Hoist for lifting a car.

The Lifting Operations and Lifting Equipment Regulations specify examinations required for lifting equipment by using two terms – an inspection and a thorough examination. Both terms are deﬁned by the HSE in guidance accompanying various regulations. An inspection is used to identify whether the equipment can be operated, adjusted and maintained safely so that any defect, damage or wear can be detected before it results in unacceptable risks. It is normally performed by a competent person appointed by the employer (often an employee). A thorough examination is a detailed examination, which may involve a visual check, a disassembly and testing of components and/or an equipment test under operating conditions. Such an examination must normally be carried out by a competent person who is independent of the employer. The examination is usually carried out according to a written scheme and a written report is submitted to the employer. A detailed summary of the thorough examination and inspection requirements of the Lifting Operations and Lifting Equipment Regulations is given in Chapter 17. A thorough examination of lifting equipment should be undertaken at the following times: ➤ before the equipment is used for the ﬁrst time ➤ after it has been assembled at a new location ➤ at least every 6 months for equipment for lifting persons or a lifting accessory ➤ at least every 12 months for all other lifting equipment including the lifting of loads over people ➤ in accordance with a particular examination scheme drawn up by an independent competent person ➤ each time that exceptional circumstances, which are likely to jeopardize the safety of the lifting equipment, have occurred (such as severe weather). The person making the thorough examination of lifting equipment must:

Figure 10.13

Specially designed safety hooks.

them. Training and instruction in the use of lifting tackle is essential and should include regular inspections of the tackle, in addition to the mandatory thorough examinations. Finally, care should be taken when these items are being stored between use.

154

➤ notify the employer forthwith of any defect which, in their opinion, is or could become dangerous ➤ as soon as practicable (within 28 days) write an authenticated report to the employer and any person who leased or hired the equipment. The Regulations specify the information that should be included in the report. The initial report should be kept for as long as the lifting equipment is used (except for a lifting accessory which need only be kept for two years). For all other

Manual and mechanical handling hazards and control examinations, a copy of the report should be kept until the next thorough examination is made or for two years (whichever is the longer). If the report shows that a defect exists, which could lead to an existing or imminent risk of serious personal injury, a copy of the report must be sent, by the person making the thorough examination, to the appropriate enforcing authority. The equipment should be inspected at suitable intervals between thorough examinations. The frequency and the extent of the inspection is determined by the level of risk presented by the lifting equipment. A report or record should be made of the inspection which should be kept until the next inspection. Unless stated otherwise, lifts and hoists should be inspected every week.

10.7 Practice NEBOSH questions for Chapter 10 1.

(a) List TWO types of injury that may be caused by the incorrect manual handling of loads (b) Outline a good lifting technique that could be adopted by a person required to lift a load from the ground (c) Give TWO examples of how a manual handling task might be avoided.

2.

(a) List FOUR speciﬁc types of injury that may be caused by the incorrect manual handling of loads (b) Outline the factors in relation to the load that will affect the risk of injury.

3.

A storeman is required to place boxes of metal components by hand on to shelved racking. (i) List FOUR types of injury to which the storeman may be at risk while carrying out this operation (ii) Outline the factors in relation to the task that may affect the risk of injury.

Outline the factors associated with the task and work environment that would need to be considered in order to complete the assessment. 7. Outline the factors that may affect the risk from manual handling activities in relation to: (i) the load (ii) the individual. 8. An automated piece of equipment designed to lift boxes weighing 20 kg from a conveyor and place them on to pallets has failed and is likely to be out of action for several weeks. During this time, the task will be carried out manually. (i) Outline the factors that should be considered when undertaking a manual handling assessment of the task (ii) Outline the measures that may be needed in order to reduce the risk of injury to employees carrying out the manual handling task. 9. Outline the issues to be considered when undertaking a manual handling assessment of a task that involves lifting buckets of water out of a sink. 10. Newspapers are printed, bundled and placed on to roller conveyors at a publisher’s where they are transported to an area for despatch to the customer. Identify EIGHT hazards to which employees involved with the transport of the newspapers from the printing room to the despatch room may be exposed. 11. Outline factors to be considered when undertaking a manual handling assessment of the work undertaken by baggage handlers at a large, busy airport. 12. Outline FOUR hazards and the corresponding precautions to be taken when using conveyor systems for moving materials within a workplace.

4.

Employees working for a charity are required to collect plastic bags of clothes, books and other donated goods from outside householders’ premises and carry them to a waiting company van. Giving reasons in EACH case, outline the types of injury the employees may sustain from the activity.

13. Drivers of internal transport are required to be competent before they are permitted to drive vehicles within the workplace. (i) Explain the meaning of the term ‘competence’ (ii) Identify measures an employer can take in order to ensure that their drivers of internal transport are, and remain, competent.

5.

(a) Outline the main requirements of the Manual Handing Operations Regulations 1992 (b) List the possible indications of a manual handling problem in a workplace.

14. Outline the health and safety topics that should be covered in a training course for fork lift truck operators.

An assessment has concluded that the person carrying out a particular manual handling task is ﬁt and capable of lifting the loads involved.

15. Outline the health and safety considerations when a fork-lift truck is to be used to unload palletized goods from a vehicle parked in a factory car park.

6.

155

Introduction to Health and Safety at Work 16. Outline EIGHT types of hazard associated with the operation of fork lift trucks. 17. List EIGHT items to be included on a checklist for the routine inspection of a fork-lift truck at the beginning of a shift. 18. Battery operated fork-lift trucks are used to move materials within a warehouse. (i) Describe FOUR hazards associated speciﬁcally with battery-powered fork-lift trucks (ii) Outline the precautions that may be needed to ensure the safety of pedestrians in areas where the fork-lift trucks are operating (iii) Outline EIGHT rules to follow when a fork-lift truck is left unattended during a driver’s work break. 19. Identify EIGHT ways in which a fork lift truck may become unstable whilst in operation. 20. A driver of a fork-lift truck has been seriously injured after the vehicle he was driving overturned. Outline the possible immediate causes of the accident associated with: (i) the way in which the vehicle was driven (ii) the workplace (iii) the vehicle. 21. An organization is about to purchase a fork-lift truck. With reference to its possible intended use and working environment, outline the particular features of the vehicle that should be taken into account when determining its suitability for the job. 22. (a) List THREE types of cranes used for lifting operations

Appendix 10.1

(b) Outline a procedure for the safe lifting of a load by a crane, having ensured that the crane has been correctly selected and positioned for the job. 23. Outline the precautions to be taken when employees are working at ground level in a workshop where loads are lifted and transported by means of an overhead gantry crane. 24. An engineering workshop uses an overhead gantry crane to transport materials. (i) Identify TWO reasons why loads may fall from this crane (ii) Outline precautions to prevent accidents to employees working at ground level when overhead cranes are in use. 25. Outline the precautions that should be taken to reduce the risk of injury during lifting operations with a mobile jib crane. 26. (a) Identify TWO occasions when a thorough examination of a fork-lift truck is required under the Lifting Operations and Lifting Equipment Regulations 1998 (b) Outline a range of circumstances that may cause a fork-lift truck to become unstable (c) Other than those associated with instability, identify FIVE hazards presented by a diesel-powered fork-lift truck AND describe the precautions that might be necessary in EACH case. 27. Describe the occasions when a thorough examination of workplace lifting equipment should be undertaken.

Manual handling of load assessment checklist

Section A – Preliminary assessment Task description:

Factors beyond the limits of the guidelines?

Is an assessment needed? (i.e. is there a potential risk of injury, and are the factors beyond the limits of the guidelines?) Yes/No

If ‘YES’ continue. If ‘NO’ no further assessment required. Tasks covered by this assessment: Location:

156

Diagram and other information

Manual and mechanical handling hazards and control

People involved: Date of assessment: Section B – See detailed analysis form Section C – Overall assessment of the risk of injury? Low/Med/High Section D – Remedial action needed: Remedial action, in priority order: a b c d e f g h Date action should be completed:

Date for review:

Assessor’s name:

Signature: Manual Handling Risk Assessment

Task description

Employee I.D. Number Risk Factors

A. Task characteristics

Yes/No

Risk Level H

M

L

Current Controls See guidance

1. Loads held away from trunk? 2. Twisting? 3. Stooping? 4. Reaching upwards? 5. Extensive vertical movements? 6. Long carrying distances? 7. Strenuous pushing or pulling? 8. Unpredictable movements of loads? 9. Repetitive handling operations? 10. Insufﬁcient periods of rest/recovery? 11. High work rate imposed?

157

Introduction to Health and Safety at Work B. Load characteristics 1.

Heavy?

2.

Bulky?

3.

Difﬁcult to grasp?

4.

Unstable/unpredictable?

5.

Harmful (sharp/hot)?

C. Work environment characteristics 1.

Postural constraints?

2.

Floor suitability?

3.

Even surface?

4.

Thermal/humidity suitability?

5.

Lighting suitability?

D. Individual characteristics 1.

Unusual capability required?

2.

Hazard to those with health problems?

3.

Hazard to pregnant workers?

4.

Special information/training required?

E. Other factors to consider 1.

Movement or posture hindered by protective clothing?

2.

Absence of correct/ suitable PPE?

3.

Lack of planning and scheduling of basics/rest basics?

4.

Poor communication between managers and employees?

5.

Sudden changes in workload or seasonal changes in volume without mechanisms to deal with change?

6.

Lack of training and/or information?

7.

Any learning disabilities?

Any further action needed? Details:

158

Yes/No

Work equipment hazards and control

11.1 Introduction This chapter covers the scope and main requirements for work equipment as covered by Parts II and III of the Provision and Use of Work Equipment Regulations (PUWER). The requirements for the supply of new machinery are also included. Summaries of PUWER and The Supply of Machinery (Safety) Regulations are given in Chapter 17. The safe use of hand tools, hand-held power tools and the proper safe-guarding of a small range of machinery used in industry and commerce is included.

11

11.2 Suitability of work equipment and CE marking When work equipment is provided it has to conform to standards which cover its supply as a new or secondhand piece of equipment and its use in the workplace. This involves: ➤ its initial integrity ➤ the place where it will be used ➤ the purpose for which it will be used. There are two groups of law that deal with the provision of work equipment:

Figure 11.1

Typical machinery safety notice.

Any equipment used by an employee at work is generally covered by the term ‘Work Equipment’. The scope is extremely wide and includes, hand tools, power tools, ladders, photocopiers, laboratory apparatus, lifting equipment, fork lift trucks, and motor vehicles (which are not privately owned). Virtually anything used to do a job of work, including employees’ own equipment, is covered. The uses covered include starting or stopping the equipment, repairing, modifying, maintaining, servicing, cleaning and transporting. Employers and the self-employed must ensure that work equipment is suitable; maintained; inspected if necessary; provided with adequate information and instruction; and only used by people who have received sufﬁcient training.

➤ one deals with what manufacturers and suppliers have to do. This can be called the ‘supply’ law. One of the most common of these is the Supply of Machinery (Safety) Regulations 1992, which requires manufacturers and suppliers to ensure that machinery is safe when supplied and has CE marking. Its primary purpose is to prevent barriers to trade across the EU, and not to protect people at work ➤ the other deals with what the users of machinery and other work equipment have to do. This can be called the ‘user’ law, PUWER 98 and applies to most pieces of work equipment. Its primary purpose is to protect people at work.

Figure 11.2

CE mark.

159

Introduction to Health and Safety at Work Under ‘user’ law employers have to provide safe equipment of the correct type; ensure that it is correctly used; and maintain it in a safe condition. When buying new equipment the ‘user’ has to check that the equipment complies with all the ‘supply’ law that is relevant. The user must check that the machine is safe before it is used. Most new equipment, including machinery in particular, should have ‘CE’ marking when purchased. ‘CE’ marking is only a claim by the manufacturer that the equipment is safe and that they have met relevant supply law. If this is done properly manufacturers will have to do the following: ➤ ﬁnd out about the health and safety hazards (trapping, noise, crushing, electrical shock, dust, vibration, etc.) that are likely to be present when the machine is used ➤ assess the likely risks ➤ design out the hazards that result in risks or, if that is not possible ➤ provide safeguards (e.g. guarding dangerous parts of the machine, providing noise enclosures for noisy parts) or, if that is not possible ➤ use warning signs on the machine to warn of hazards that cannot be designed out or safeguarded (e.g. ‘noisy machine’ signs). Manufacturers also have to: ➤ keep information, explaining what they have done and why, in a technical ﬁle ➤ ﬁx CE marking to the machine where necessary, to show that they have complied with all the relevant supply laws ➤ issue a ‘Declaration of Conformity’ for the machine (see Figure 11.3). This is a statement that the machine complies with the relevant essential health and safety requirements or with the example that underwent type-examination. A declaration of conformity must ➤ state the name and address of the manufacturer or importer into the EU ➤ contain a description of the machine, its make, type and serial number ➤ indicate all relevant European directives with which the machinery complies ➤ state details of any notiﬁed body that has been involved ➤ specify which standards have been used in the manufacture (if any) ➤ be signed by a person with authority to do so ➤ provide the buyer with instructions to explain how to install, use and maintain the machinery safely.

160

Figure 11.3

Typical certificate of conformity.

This can help to decide which equipBefore buying new equipment may be suitable, ment the buyer will need particularly if buyto think about: ing a standard piece of equipment ‘off the ➤ where and how it will shelf’. be used If buying a more ➤ what it will be used complex or customfor built machine the ➤ who will use it (skilled buyer should discuss employees, trainees) their requirements with ➤ what risks to health potential suppliers. For and safety might a custom-built piece result of equipment, there ➤ how well health and is the opportunity to safety risks are conwork with the supplier trolled by different to design out the manufacturers. causes of injury and ill-health. Timespent now on agreeing the necessary safeguards, to control health and safety risks, could save time and money later. Note: Sometimes equipment is supplied via another organization, for example, an importer, rather than direct from the manufacturer, so this other organization is referred to as the supplier. It is important to realize that the supplier may not be the manufacturer. When the equipment has been supplied the buyer should look for CE marking, check for a copy of the Declaration of Conformity and that there is a set of instructions in English on how the machine should be used and most important of all, check to see if they think that it is safe.

Work equipment hazards and control 11.3 Use and maintenance of equipment with specific risks Some pieces of work equipment involve speciﬁc risks to health and safety where it is not possible to control adequately the hazards by physical measures alone, for example, the use of a bench-mounted circular saw or an abrasive wheel. In all cases the hierarchy of controls should be adopted to reduce the risks by: ➤ eliminating the risks or, if this is not possible ➤ taking physical measures to control the risks such as guards, but if the risks cannot be adequately controlled ➤ taking appropriate software measures, such as a safe system of work.

reduced by physical means, require enough information, instruction and training to operate safely. The information and instructions are likely to come from the manufacturer in the form of operating and maintenance manuals. It is up to the employer to ensure that what is provided is easily understood, set out logically with illustrations and standard symbols where appropriate. The information should normally be in good plain English but other languages may be necessary in some cases. The extent of the information and instructions will depend on the complexity of the equipment and the speciﬁc risks associated with its use. They should cover: ➤ ➤ ➤ ➤ ➤

all safety and health aspects any limitations on the use of the equipment any foreseeable problems that could occur safe methods to deal with the problems any relevant experience with the equipment that would reduce the risks or help others to work more safely, should be recorded and circulated to everyone concerned.

Everyone who uses and maintains work equipment needs to be adequately trained. The amount of training required will depend on: ➤ the complexity and level of risk involved in using or maintaining the equipment ➤ the experience and skills of the person doing the work, whether it is normal use or maintenance. Figure 11.4

Using a bench-mounted abrasive wheel.

PUWER 98 Regulation 7 restricts the use of such equipment to the persons designated to use it. These people need to have received sufﬁcient information, instruction and training so that they can carry out the work using the equipment safely. Repairs, modiﬁcations, maintenance or servicing is also restricted to designated persons. A designated person may be the operator if they have the necessary skills and have received speciﬁc instruction and training. Another person speciﬁcally trained to carry out a particular maintenance task, for example, dressing an abrasive wheel, may not be the operator but designated to do this type of servicing task on a range of machines.

11.4 Information, instruction and training People using and maintaining work equipment, where there are residual risks that cannot be sufﬁciently

Training needs will be greatest when a person is ﬁrst recruited but will also need to be considered: ➤ when working tasks are changed, particularly if the level of risk changes ➤ if new technology or new equipment is introduced ➤ where a system of work changes ➤ when legal requirements change ➤ periodically to update and refresh peoples’ knowledge and skills. Supervisors and managers also require adequate training to carry out their function, particularly if they only supervise a particular task occasionally. The training and supervision of young persons is particularly important because of their relative immaturity, unfamiliarity with a working environment and awareness of existing or potential risks. Some Approved Codes of Practice, for example on the Safe Use of Woodworking Machinery restrict the use of high-risk machinery, so that only young persons with sufﬁcient maturity and competence, who have ﬁnished their training, may use the equipment unsupervised.

161

Introduction to Health and Safety at Work 11.5 Maintenance and inspection 11.5.1

Maintenance

Work equipment needs to be properly maintained so that it continues to operate safely and in the way it was designed to perform. The amount of maintenance will be stipulated in the manufacturers’ instructions and will depend on the amount of use, the working environment and the type of equipment. High speed, high risk machines, which are heavily used in an adverse environment like salt water, may require very frequent maintenance, whereas a simple hand tool, like a shovel, may require very little.

Figure 11.5

Typical maintenance notice.

Maintenance management schemes can be based around a number of techniques designed to focus on those parts which deteriorate and need to be maintained to prevent health and safety risks. These techniques include: ➤ preventative planned maintenance – which involves replacing parts and consumables or making necessary adjustments at preset intervals, normally set by the manufacturer, so that there are no hazards created by component deterioration or failure. Vehicles are normally maintained on this basis ➤ condition based maintenance – this involves monitoring the condition of critical parts and carrying out maintenance whenever necessary to avoid hazards which could otherwise occur ➤ breakdown based maintenance – here maintenance is only carried out when faults or failures have occurred. This is only acceptable if the failure does not present an immediate hazard and can be corrected before the risk is increased. If, for example, a bearing overheating can be detected by a monitoring device, it is acceptable to wait for the overheating to occur as long as the equipment can be stopped and repairs carried out before the fault becomes dangerous to persons employed.

162

In the context of health and safety, maintenance is not concerned with operational efﬁciency but only with avoiding risks to people. It is essential to ensure that maintenance work can be carried out safely. This will involve: ➤ competent well-trained maintenance people ➤ the equipment being made safe for the maintenance work to be carried out. In many cases the normal safeguards for operating the equipment may not be sufﬁcient as maintenance sometimes involves going inside guards to observe and subsequently adjust, lubricate or repair the equipment. Careful design allowing adjustments, lubrication and observation from outside the guards, for example, can often eliminate the hazard. Making equipment safe will usually involve disconnecting the power supply and then preventing anything moving, falling or starting during the work. It may also involve waiting for equipment to cool or warm up to room temperature ➤ a safe system of work being used to carry out the necessary procedures to make and keep the equipment safe and perform the maintenance tasks. This can often involve a formal ‘permit to work’ scheme to ensure that the correct sequence of safety critical tasks has been performed and all necessary precautions taken ➤ correct tools and safety equipment being available to perform the maintenance work without risks to people. For example special lighting or ventilation may be required.

11.5.2

Inspection under PUWER

Complex equipment and/or high-risk equipment will probably need a maintenance log and may require a more rigid inspection regime to ensure continued safe operation. This is covered by PUWER 98, Regulation 6. PUWER requires that where safety is dependent on the installation conditions and/or the work equipment is exposed to conditions causing deterioration, which may result in a signiﬁcant risk and a dangerous situation developing, that the equipment is inspected by a competent person. In this case the competent person would normally be an employee, but there may be circumstances like fairground equipment, where an outside competent person would be used. The inspection must be done: ➤ after installation for the ﬁrst time ➤ after assembly at a new site or in a new location and thereafter ➤ at suitable intervals and ➤ each time exceptional circumstances occur which could affect safety.

Work equipment hazards and control The inspection under PUWER will vary from a simple visual inspection to a detailed comprehensive inspection, which may include some dismantling and/or testing. The level of inspection required would normally be less rigorous and intrusive than thorough examinations under the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) for certain lifting equipment. In the case of boilers and air receivers the inspection is covered by the Pressure Systems Safety Regulations 2000 which involves a thorough examination (see the summary in Chapter 17). The inspection under PUWER would only be needed in these cases if the examinations did not cover all the signiﬁcant health and safety risks that are likely to arise.

11.5.3

➤ that a report of the periodic examination is held on ﬁle giving the required particulars ➤ the actions required by the report are carried out ➤ any other safety critical maintenance work is carried out, whether or not covered by the report. In these cases the competent person is usually a specialist inspector from an external inspection organization. Many of these organizations are linked to the insurance companies who cover the ﬁnancial risks of the pressure vessel.

11.6 Operation and working environment

Examination of boilers and air receivers

Under the Pressure Systems Safety Regulations 2000, a wide range of pressure vessels and systems require thorough examination by a competent person to an agreed speciﬁcally written scheme. This includes steam boilers, pressurized hot water plants and air receivers which are contained in the Certiﬁcate syllabus. The Regulations place duties on designers and manufacturers but this section is only concerned with the duty on users to have the vessels examined. An employer who operates a steam boiler and/or a pressurized hot water plant and/or an air receiver must ensure: ➤ that it is supplied with the correct written information and markings ➤ that the equipment is properly installed ➤ that it is used within its operating limits ➤ there is a written scheme for periodic examination of the equipment certiﬁed by a competent person (in the case of standard steam boilers and air receivers the scheme is likely to be provided by the manufacturer) ➤ that the equipment is examined in accordance with the written scheme by a competent person within the speciﬁed period

Figure 11.6

Typical compressor and air receiver.

To operate work equipment safely it must be ﬁtted with easily reached and operated controls; kept stable; properly lit; kept clear; and provided with adequate markings and warning signs. These are covered by PUWER 98, which applies to all types of work equipment.

Equipment controls should: ➤ be easily reached from the operating positions ➤ not permit accidental starting of equipment ➤ move in the same direction as the motion being controlled ➤ vary in mode, shape and direction of movement to prevent inadvertent operation of the wrong control ➤ incorporate adequate red emergency stop buttons ➤ incorporate adequate red emergency stop buttons, of the mushroom headed type with lock-off ➤ have shrouded or sunk green start buttons to prevent accidental starting of the equipment ➤ be clearly marked to show what they do.

Equipment should be operated in clear unobstructed work areas, particularly if they are high-risk machines. Debris and rubbish given off from the equipment should be removed quickly. Sometimes there will be need for special systems to remove waste to prevent accumulations of dust and/or substances hazardous to health, for example, wood dust from wood working machinery. Equipment should be provided with efﬁcient means of isolating it from all sources of energy. In many cases this source is the mains electrical energy but it must cover

163

Introduction to Health and Safety at Work all sources such as steam, compressed air, hydraulic, batteries, heat, etc. In some cases special consideration is necessary where, for example, hydraulic power is switched off, not to let heavy pieces of equipment like the ram, fall under gravity. Emergency stop must be provided where the other safeguards in place are not adequate to prevent danger. Where appropriate, there should be an emergency stop at each control point and at other locations around the equipment so that action can be taken quickly. They should bring the equipment to a halt rapidly but this should be controlled where necessary so as not to create any additional hazards. Emergency stop buttons should be easily reached and operated. Common types are mushroom-headed buttons, bars, levers, kick-plates, or pressure sensitive cables. They are normally red and should need to be reset after use. With stop buttons this is either by twisting or a security key. See Figure 11.7. Stability is important and is normally achieved by bolting equipment in place or if this is not possible by using clamps. Some equipment can be tied down, counterbalanced or weighted, so that it remains stable under all operating conditions. If portable equipment is weighted or counterbalanced it should be reappraised when the equipment is moved to another position. If outriggers are needed for stability in certain conditions, for example, to stabilize mobile access towers, they

should be employed whenever conditions warrant the additional support. In severe weather conditions it may be necessary to stop using the equipment or reappraise the situation to ensure stability is maintained. The quality of general and local lighting will need to be considered to ensure the safe operation of the equipment. The level of lighting and its position relative to the working area are often critical to the safe use of work equipment. Poor levels of lighting, glare and shadows can be dangerous when operating equipment. Some types of lighting, for example, sodium lights, can change the colour of equipment, which may increase the level of risk. This is particularly important if the colour coding of pipe work or cables is essential for safety. Markings on equipment must be clearly visible and durable. They should follow international conventions for some hazards like radiation and lasers and, as far as possible, conform to the Health and Safety (Safety Signs and Signals) Regulations (see Chapter 17 for a summary). The contents, or the hazards of the contents, as well as controls, will need to be marked on some equipment. Warnings or warning devices are required in some cases to alert operators or people nearby to any dangers, for example, ‘wear hardhats’; a ﬂashing light on an airport vehicle; or a reversing horn on a truck.

11.7 User responsibilities The responsibilities on users of work equipment are covered in section 7 of HSW Act and regulation 14 of the Management Regulations. Section 7 requires employees to take reasonable care for themselves and others who may be affected and to cooperate with the employer. Regulation 12 requires employees to use equipment properly in accordance with instructions and training. They must also inform employers of dangerous situations and shortcomings in protection arrangements. The self-employed who are users have similar responsibilities to employers and employees combined.

11.8 Hand-held tools Work equipment includes hand tools and hand-held power tools. These tools need to be correct for the task, well maintained and properly used. Hazards from the misuse or poor maintenance of hand tools include:

Figure 11.7

164

Emergency stop buttons.

➤ broken handles on ﬁles/chisels/screwdrivers/hammers which can cause cut hands or hammer heads to ﬂy off ➤ incorrect use of knives, saws and chisels with hands getting injured in the path of the cutting edge

Work equipment hazards and control Suitability – all tools should be suitable for the purpose and location in which they are to be used. This will include: ➤ specially protected and insulated tools for electricians ➤ non-sparking tools for ﬂammable atmospheres and the use of non-percussion tools and cold cutting methods ➤ tools made of suitable quality materials which will not chip or splay in normal use ➤ the correct tools for the job, for example, using the right-sized spanner and the use of mallets on chisel heads ➤ safety knives with enclosed blades for regular cutting operations ➤ scissors with blunted ends. Inspection – all tools should be maintained in a safe and proper condition. This can be achieved through:

Figure 11.8

Typical range of hand tools.

➤ tools that slip causing stab wounds ➤ poor quality uncomfortable handles that damage hands ➤ splayed spanners that slip and damage hands or faces ➤ chipped or loose hammer heads that ﬂy off or slip ➤ incorrectly sharpened chisels that slip and cut hands ➤ ﬂying particles that damage eyes from breaking up stone or concrete ➤ electrocution or burns by using incorrect or damaged tools for electrical work ➤ use of poorly insulated tools for hot work in catering or food industry ➤ use of pipes or similar equipment as extension handles for a spanner which is likely to slip causing hand or face injury ➤ mushroom headed chisels or drifts which can damage hands or cause hammers (not suitable for chisels) and mallets to slip ➤ use of spark producing or percussion tools in ﬂammable atmospheres.

11.8.1

Hand tools

Hand tools should be properly controlled including those tools owned by employees. The following controls are important.

➤ the regular inspection of hand tools ➤ discarding or prompt repair of defective tools ➤ taking time to keep tools in the proper condition and ready for use ➤ proper storage to prevent damage and corrosion ➤ locking tools away when not in use to prevent them being used by unauthorized people. Training – all users of hand tools should be properly trained in their use. This may well have been done through apprenticeships and similar training. This will be particularly important with specialist working conditions or work involving young people.

11.8.2

Hand-held power tools

Hazards The electrical hazards of portable hand-held tools are covered in Chapter 10. This section deals with other physical hazards relating to this type of equipment, particularly a drill and sander. Other hazards involve: ➤ mechanical entanglement in rotating spindles or sanding discs ➤ waste material ﬂying out of the cutting area ➤ coming into contact with the cutting blades or drill bits ➤ risk of hitting electrical, gas or water services when drilling into building surfaces ➤ manual handling problem with a risk of injury if the tool is heavy or very powerful ➤ hand–arm vibration especially with petrol strimmers and chainsaws ➤ tripping hazard from trailing cables or power supplies ➤ eye hazard from ﬂying particles

165

Introduction to Health and Safety at Work

Figure 11.9

Typical range of hand-held power tools.

➤ explosion risk with petrol driven tools or when used near ﬂammable liquids or gases ➤ high noise levels with routers, planes and saws in particular (see Chapter 15) ➤ dust levels (see Chapter 14).

Typical safety instructions and controls When using power tools, the following basic safety measures should be observed to protect against electrical shock, personal injury, ill-health and risk of ﬁre. Operators should read these instructions before using the equipment and ensure that they are followed: ➤ maintain a clean and tidy working area that is well lit and clear of obstructions ➤ never expose power tools to rain. Do not use power tools in damp or wet surroundings ➤ do not use power tools in the vicinity of combustible ﬂuids or gases ➤ protect against electrical shock (if tools are electrically powered) by avoiding body contact with grounded objects such as pipes, radiators, stoves and refrigerators ➤ keep children away ➤ do not let other persons handle the tool or the cable. Keep them away from the working area

166

➤ store tools in a safe place when not in use where they are in a dry, locked area, which is inaccessible to children ➤ tools should not be overloaded as they operate better and safer in the performance range for which they were intended ➤ use the right tool. Do not use small tools or attachments for heavy work. Do not use tools for purposes and tasks for which they were not intended; for example, do not use a hand-held circle saw to cut down trees or cut off branches ➤ wear suitable work clothes. Do not wear loose ﬁtting clothing or jewellery. They can get entangled in moving parts. For outdoor work, rubber gloves and nonskid footwear are recommended. Long hair should be protected with a hair net ➤ use safety glasses ➤ also use a ﬁltering respirator mask for work that generates dust ➤ do not abuse the power cable ➤ do not carry the tool by the power cable and do not use the cable to pull the plug out of the power socket. Protect the cable from heat, oil and sharp edges ➤ secure the work piece. Use clamps or a vice to hold work piece. It is safer than using hands and it frees both hands for operating the tool ➤ do not overreach the work area. Avoid abnormal body postures. Maintain a safe stance and maintain a proper balance at all times ➤ maintain tools with care. Keep your tools clean and sharp for efﬁcient and safe work. Follow the maintenance regulations and instructions for the changing of tools. Check the plug and cable regularly and in case of damage, have repaired by a qualiﬁed service engineer. Also inspect extension cables regularly and replace if damaged ➤ keep the handle dry and free of oil or grease ➤ disconnect the power plug when not in use, before servicing and when changing the tool, i.e. blade, bits, cutter, sanding disc, etc. ➤ do not forget to remove key. Check before switching on that the key and any tools for adjustment are removed ➤ avoid unintentional switch-on. Do not carry tools that are connected to power with your ﬁnger on the power switch. Check that the switch is turned off before connecting the power cable ➤ outdoors use extension cables. When working outdoors, use only extension cables which are intended for such use and marked accordingly ➤ stay alert, keep eyes on the work. Use common sense. Do not operate tools when there are signiﬁcant distractions ➤ check the equipment for damage. Before further use of a tool, check carefully the protection devices

Work equipment hazards and control or lightly damaged parts for proper operation and performance of their intended functions. Check movable parts for proper function, whether there is binding or for damaged parts. All parts must be correctly mounted and meet all conditions necessary to ensure proper operation of the equipment ➤ damaged protection devices and parts should be repaired or replaced by a competent service centre unless otherwise stated in the operating instructions. Damaged switches must be replaced by a competent service centre. Do not use any tool which cannot be turned on and off with the switch ➤ only use accessories and attachments that are described in the operating instructions or are provided or recommended by the tool manufacturer. The use of tools other than those described in the

operating instructions or in the catalogue of recommended tool inserts or accessories can result in a risk of personal injury.

11.9 Mechanical machinery hazards Most machinery has the potential to cause injury to people, and machinery accidents ﬁgure prominently in ofﬁcial accident statistics. These injuries may range in severity from a minor cut or bruise, through various degrees of wounding and disabling mutilation, to crushing, decapitation or other fatal injury. Nor is it solely powered machinery that is hazardous, for many manually operated machines (e.g. hand-operated guillotines and ﬂy presses) can still cause injury if not properly safeguarded.

Scissor lifts

Trap against fixed structures

Crushing Hazards Rotating spoked wheels

Radial flow fans

Shear Hazards Band saw blades

Axial flow fans

Cutting Hazards

Figure 11.10

Range of mechanical hazards.

167

Introduction to Health and Safety at Work Chains and sprockets

Rack and pinion gears

Pulley belts

Belt conveyor

Meshing gears

Counter-rotating rolls

Drawing-in Hazards

Figure 11.10

Abrasive wheels

Shaft with projections

Abrasion and Ejection Hazard

Entanglement Hazard

Continued.

Machinery movement basically consists of rotary, sliding or reciprocating action, or a combination of these. These movements may cause injury by entanglement, friction or abrasion, cutting, shearing, stabbing or puncture, impact, crushing, or by drawing a person into a position where one or more of these types of injury can occur. The hazards of machinery are set out in BS EN ISO 12100 – Part 2: 2003 which covers the classiﬁcation of machinery hazards and how harm may occur. The following machinery hazards follow this standard. A person may be injured at machinery as a result of: ➤ a crushing hazard through being trapped between a moving part of a machine and a ﬁxed structure, such as a wall or any material in a machine ➤ a shearing hazard which traps part of the body, typically a hand or ﬁngers, between moving and ﬁxed parts of the machine ➤ a cutting or severing hazard through contact with a cutting edge, such as a band saw or rotating cutting disc

168

➤ entanglement hazard with the machinery which grips loose clothing, hair or working material, such as emery paper, around revolving exposed parts of the machinery. The smaller the diameter of the revolving part the easier it is to get a wrap or entanglement ➤ a drawing-in or trapping hazard such as between in-running gear wheels or rollers or between belts and pulley drives ➤ an impact hazard when a moving part directly strikes a person, such as with the accidental movement of a robot’s working arm when maintenance is taking place ➤ a stabbing or puncture hazard through ejection of particles from a machine or a sharp operating component like a needle on a sewing machine ➤ contact with a friction or abrasion hazard, for example, on grinding wheels or sanding machines ➤ high pressure fluid injection (ejection hazard), for example, from a hydraulic system leak.

Work equipment hazards and control In practice, injury may involve several of these at once, for example, contact, followed by entanglement of clothing, followed by trapping.

11.10.2

Employees carried on mobile work equipment – Regulation 25

No employee may be carried on mobile work equipment unless:

11.10

Mobile work equipment

11.10.1

Hazards of mobile equipment

Injuries from mobile equipment are predominantly related to:

➤ it is suitable for carrying persons ➤ it incorporates features to reduce risks as low as is reasonably practicable, including risks from wheels and tracks ➤ Where there is a signiﬁcant risk of falling materials ﬁt falling-object protective structures (FOPS)

➤ Poor maintenance with defective brakes, tyres and steering ➤ Poor visibility because of dirty mirrors and windows or loads which obstruct the drivers’ view ➤ Operating on rough ground or steep gradients which causes the mobile equipment to turn on its side 90º plus or roll over 180º or more ➤ Carrying of passengers without the proper accommodation for them ➤ People being ﬂung out as they overturn and being crushed by the vehicle ➤ Being crushed under wheels as the vehicle moves ➤ Being struck by a vehicle or an attachment ➤ Lack of driver training or experience ➤ Underlying causes of poor management procedures and controls, safe working practices, information, instruction, training and supervision.

Rolling over of mobile work equipment

The machines most at risk of roll over according to the HSE are:

➤ facilities to prevent unauthorized starting ➤ (with multiple rail-mounted equipment) facilities to minimize the consequences of collision ➤ a device for braking and stopping ➤ (where safety constraints so require) emergency facilities for braking and stopping, in the event of failure of the main facility, which have readily accessible or automatic controls ➤ (where the driver’s vision is inadequate) devices ﬁtted to improve vision ➤ (if used at night or in dark places) appropriate lighting ﬁtted or otherwise it shall be made sufﬁciently safe for its use ➤ if there is anything carried or towed that constitutes a ﬁre hazard liable to endanger employees (particularly if escape is difﬁcult such, as from a tower crane), appropriate ﬁre-ﬁghting equipment carried, unless it is sufﬁciently close by.

➤ compact dumpers ➤ agricultural tractors ➤ variable reach rough terrain trucks (telehandlers). The main purpose of the mobile work equipment PUWER 1998 Part III, Regulations 25 to 30 is to require additional precautions relating to work equipment while it is travelling from one location to another or where it does work while moving. All appropriate sections of PUWER 98 will also apply to mobile equipment as it does to all work equipment, for example dangerous moving parts of the engine would be covered by Part II Regulations 10, 11 and 12 of PUWER 98. If the equipment is designed primarily for travel on public roads the Road Vehicles (Construction and Use) Regulations 1986 will normally be sufﬁcient to comply with PUWER 98. Mobile equipment would normally move on, wheels, tracks, rollers, skids, etc. Mobile equipment may be selfpropelled, towed or remote controlled and may incorporate attachments. Pedestrian controlled work equipment, such as lawn mowers, are not covered by Part III.

Where there is a risk of overturning it must be minimized by: ➤ stabilizing the equipment ➤ ﬁtting a structure so that it only falls on its side ➤ ﬁtting a structure which gives sufﬁcient clearance for anyone being carried if it turns over further ROPS (Roll Over Protection Structure) ➤ a device giving comparable protection ➤ ﬁtting a suitable restraining system for people if there is a risk of being crushed by rolling over.

Self-propelled work equipment Where self-propelled work equipment may involve risks while in motion they shall have:

11.10.3

Rollover and falling object protection (ROPS and FOPS)

Rollover protective structures are now becoming much more affordable and available for most types of mobile

169

Introduction to Health and Safety at Work

Figure 11.11

Various construction plant with driver protection.

equipment where there is a high risk of turning over. There use is spreading across most developed countries and even some less well developed areas. A ROP is a cab or frame that provides a safe zone for the vehicle operator in the event of a rollover. The ROPS frame must pass a series of static and dynamic crush tests. These tests examine the ability of the ROPS to withstand various loads to see if the protective zone around the operator remains intact in an overturn. A home made bar attached to a tractor axle or simple shelter from the sun or rain cannot protect the operator if the equipment overturns. The ROPS must meet International Standards such as ISO 3471:1994. All mobile equipment safeguards should comply with the essential health and safety requirements of the Supply of Machinery (Safety) Regulations 1992 but need not carry a CE marking. ROPS must also be correctly installed strictly following the manufacturer’s instructions and using the correct strength bolts and ﬁxings. They should never be modiﬁed by drilling, cutting, welding or other means as this may seriously weaken the structure. Falling object protective structures (FOPS), are required where there is a signiﬁcant risk of objects falling on the equipment operator or other authorized person using the mobile equipment. Canopies that protect against

170

falling objects (FOPS) must be properly designed and certiﬁed for that purpose. Front loaders, working in woods or construction sites near scaffolding or buildings under construction and high bay storage areas are all locations where there is a risk of falling objects. Purchasers of equipment should check that any canopies ﬁtted are FOPS. ROPS should never be modiﬁed by the user to ﬁt a canopy without consultation with the manufacturers. ROPS provide some safety during overturning but operatives must be conﬁned to the protective zone of the ROPS. So where ROPS are ﬁtted a suitable restraining system must be provided to all seats. The use of seat restraints could avoid accidents where drivers are thrown from machines, through windows or doors or thrown around inside the cab. In agriculture and forestry, ﬁfty percent of overturning accidents occur on slopes of less than 10º and twenty ﬁve percent on slopes of 5º or less. This means that seat restraints should be used most of the time that the vehicle is being operated.

11.10.4

Fork lift trucks

The mast of a vertical-masted fork lift truck will generally prevent it turning over by more than 90º, provided it has sufﬁcient strength and dimensions for this purpose. A variable reach fork-lift truck, however, is capable of

Work equipment hazards and control rolling over 180º or more and would need to be ﬁtted with a ROPS where there is a risk of it rolling over. Fork lift trucks ﬁtted with either a mast or a roll-over protective structure, should be provided with driver restraining systems where appropriate, to prevent the driver being crushed between the truck and the ground.

11.10.5

Safe driving

Drivers have an important role to play in the safe use of mobile equipment. They should include the following in their safe working practice checklist: ➤ Make sure they understand fully the operating procedures and controls on the equipment being used ➤ Only operate equipment for which they are trained and authorized ➤ Never drive if abilities are impaired by, for example alcohol, poor vision or hearing, ill health or drugs whether prescribed or not ➤ Use the seat restraints where provided ➤ Know the site rules and signals ➤ Know the safe operating limits relating to the terrain and loads being carried ➤ Keep vehicles in a suitably clean and tidy condition with particular attention to mirrors and windows or loose items which could interfere with the controls ➤ Drive at suitable speeds and following site rules and routes at all times ➤ Only allow passengers when there are safe seats provided on the equipment ➤ Park vehicles on suitable ﬂat ground with the engine switched off and the parking brakes applied, use wheel chokes if necessary ➤ Make use of visibility aids or a signaller when vision is restricted ➤ Get off the vehicle during loading operations unless adequate protection is provided ➤ Ensure that the load is safe to move ➤ Do not get off vehicle until it is stationary, with the engine stopped and parking brake applied ➤ Where practicable remove the operating key when getting off the vehicle ➤ Take the correct precautions such as not smoking and switching off the engine when refuelling.

11.11

Non-mechanical machinery hazards

➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

lifting and handling electricity (including static electricity): shock, burns ﬁre and explosion noise and vibration pressure and vacuum high/low temperature inhalation of dust/fume/mist suffocation radiation: ionising and non-ionising biological: viral or bacterial. physiological effects (e.g. Musculo-skeletal disorders) ➤ psycho-physiological effects (e.g. mental overload or underload) ➤ human errors ➤ hazards from the environment where the machine is used (e.g. temperature, wind, snow, lightning). In many cases it will be practicable to install safeguards which protect the operator from both mechanical and non-mechanical hazards. For example, a guard may prevent access to hot or electrically live parts as well as to moving ones. The use of guards which reduce noise levels at the same time is also common. As a matter of policy machinery hazards should be dealt with in this integrated way instead of dealing with each hazard in isolation.

11.12

Examples of machinery hazards

The following examples are given to demonstrate a small range of machines found in industry and commerce, which are included in the Certiﬁcate syllabus.

Office – photocopier The hazards are: ➤ contact with moving parts when clearing a jam ➤ electrical – when clearing a jam, maintaining the machine or through poorly maintained plug and wiring ➤ heat through contact with hot parts when clearing a jam ➤ health hazard from ozone or lack of ventilation in the area.

Office – document shredder Non-mechanical hazards include:

The hazards are:

➤ access: slips, trips and falls; falling and moving objects; obstructions and projections

➤ drawing in between the rotating cutters when feeding paper into the shredder

171

Introduction to Health and Safety at Work ➤ contact with the rotating cutters when emptying the waste container or clearing a jam ➤ electrical through faulty plug and wiring or during maintenance ➤ noise from the cutting action of the machine ➤ possible dust from the cutting action.

➤ electrical if electrically powered, but this is unlikely ➤ possible sensitization health hazard from cutting grass, for example, hay fever ➤ possible health hazard from exhaust fumes.

Agriculture/horticultural – brush cutter/strimmer The hazards are:

Manufacturing and maintenance – bench top grinding machine The hazards are: ➤ contact with the rotating wheel causing abrasion ➤ drawing in between the rotating wheel and a badly adjusted tool rest ➤ bursting of the wheel, ejecting fragments which puncture the operator ➤ electrical through faulty wiring and/or earthing or during maintenance ➤ fragments given off during the grinding process causing eye injury ➤ hot fragments given off which could cause a ﬁre ➤ noise produced during the grinding process ➤ possible health hazard from dust/particles/fumes given off during grinding.

Manufacturing and maintenance – pedestal drill The hazards are: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

entanglement around the rotating spindle and chuck contact with the cutting drill or work-piece being struck by the work-piece if it rotates being cut or punctured by fragments ejected from the rotating spindle and cutting device drawing in to the rotating drive belt and pulley contact or entanglement with the rotating motor electrical from faulty wiring and/or earthing or during maintenance possible health hazard from cutting ﬂuids or dust given off during the process.

Agriculture/horticultural – cylinder mower The hazards are: ➤ trapping, typically hands or ﬁngers, in the shear caused by the rotating cutters ➤ contact and entanglement with moving parts of the drive motor ➤ drawing in between chain and sprocket drives ➤ impact and cutting injuries from the machine starting accidentally ➤ burns from hot parts of the engine ➤ ﬁre from the use of highly ﬂammable petrol as a fuel ➤ possible noise hazard from the drive motor

172

➤ entanglement with rotating parts of motor and shaft ➤ cutting from contact with cutting head/line ➤ electric shock, if electrically powered but this is unlikely ➤ burns from hot parts of the engine ➤ ﬁre from the use of highly ﬂammable petrol as a fuel ➤ possible noise hazard from the drive motor and cutting action ➤ eye and face puncture wounds from ejected particles ➤ health hazard from hand-arm vibration causing white ﬁnger and other problems ➤ back strain from carrying the machine while operating ➤ health hazards from animal faeces.

Chainsaw The hazards are: ➤ very serious cutting by contact with the high speed cutting chain ➤ kick back due to being caught on the wood being cut or contact with the top front corner of the chain in motion with the saw chain being kicked upwards towards the face in particular ➤ pull-in when the chain is caught and the saw is pulled forward ➤ pushback when the chain on the top of the saw bar is suddenly pinched and the saw is driven straight back towards the operator ➤ burns from hot parts of the engine ➤ high noise levels ➤ hand arm vibration causing white ﬁnger and other problems ➤ ﬁre from the use of highly ﬂammable petrol as a fuel ➤ eye and face puncture wounds from ejected particles ➤ back strain while supporting the weight of the chainsaw while operating ➤ electric shock if electrically powered ➤ falls from height if using the chainsaw in trees and the like ➤ lone working and the risk of serious injury ➤ contact with overhead powerlines if felling trees ➤ being hit by falling branches or whole trees while felling ➤ possible health hazards from cutting due to wood dust particularly if wood has been seasoned ➤ using chainsaw in poor weather conditions with slippery surfaces, poor visibility and cold conditions

Work equipment hazards and control ➤ health hazards from the engine fumes, (carbon dioxide and carbon monoxide) particularly if used inside a shed or other building.

Retail – compactor The hazards are: ➤ crushing hazard between the ram and the machine sides ➤ trapping between the ram and machine frame (shear action) ➤ crushing when the waste unit is being changed if removed by truck ➤ entanglement with moving parts of pump motor ➤ electrical from faulty wiring and/or earthing or during maintenance ➤ failure of hydraulic hoses with liquid released under pressure causing puncture to eyes or other parts of body ➤ falling of vertical ram under gravity if the hydraulic system fails ➤ handling hazards during loading and unloading.

Retail – checkout conveyor system

➤ ejection of the work-piece or timber as it closes after passing the cutting blade ➤ drawing-in between chain and sprocket or V belt drives ➤ contact and entanglement with moving parts of the drive motor ➤ likely noise hazards from the cutting action and motor ➤ health hazards from wood dust given off during cutting ➤ electric shock from faulty wiring and/or earthing or during maintenance.

11.13

Practical safeguards

PUWER requires that access to dangerous parts of machinery should be prevented in a preferred order or hierarchy of control methods. The standard required is a ‘practicable’ one, so that the only acceptable reason for non-compliance is that there is no technical solution. Cost is not a factor. (See Chapter 1 for more details on standards of compliance.) The levels of protection required are, in order of implementation:

The hazards are: ➤ ➤ ➤ ➤ ➤

entanglement with belt fasteners if ﬁtted drawing in between belt and rollers if under tension drawing in between drive belt and pulley contact or entanglement with motor drive electrical from faulty wiring and/or earthing or during maintenance.

Construction – cement/concrete mixer The hazards are: ➤ contact and entanglement with moving parts of the drive motor ➤ crushing between loading hopper (if ﬁtted) and drum ➤ drawing-in between chain and sprocket drives ➤ electrical, if electrically powered ➤ burns from hot parts of engine ➤ ﬁre if highly ﬂammable liquids used as fuel ➤ possible noise hazards from the motor and dry mixing of aggregates ➤ eye injury from splashing cement slurry ➤ possible health hazard from cement dust and cement slurry while handling.

➤ ﬁxed enclosing guarding ➤ other guards or protection devices, such as interlocked guards and pressure sensitive mats ➤ protection appliances, such as jigs, holders and push-sticks and ➤ the provision of information, instruction, training and supervision. Since the mechanical hazard of machinery arises principally from someone coming into contact or entanglement with dangerous components, risk reduction is based on preventing this contact occurring. This may be by means of: ➤ a physical barrier between the individual and the component (e.g. a ﬁxed enclosing guard) ➤ a device which only allows access when the component is in a safe state (e.g. an interlocked guard which prevents the machine starting unless a guard is closed and acts to stop the machine if the guard is opened) or ➤ a device which detects that the individual is entering a risk area and then stops the machine (e.g. certain photoelectric guards and pressure-sensitive mats).

Construction – bench-mounted circular saw The hazards are: ➤ contact with the cutting blade above and below the bench

The best method should, ideally, be chosen by the designer as early in the life of the machine as possible. It is often found that safeguards which are ‘bolted on’ instead of ‘built in’ are not only less effective in reducing

173

Introduction to Health and Safety at Work risk, but are also more likely to inhibit the normal operation of the machine. In addition, they may in themselves create hazards and are likely to be difﬁcult and hence expensive to maintain.

11.13.1

Fixed guards

Fixed guards have the advantage of being simple, always in position, difﬁcult to remove and almost maintenance free. Their disadvantage is that they do not always properly prevent access, they are often left off by maintenance staff and can create difﬁculties for the operation of the machine. A ﬁxed guard has no moving parts and should, by its design, prevent access to the dangerous parts of the machinery. It must be of robust construction and sufﬁcient to withstand the stresses of the process and environmental conditions. If visibility or free air ﬂow (e.g. for cooling) are necessary, this must be allowed for in the design and construction of the guard. If the guard can be

Shaft wit projectios

Adjustable guards

User adjusted guard These are ﬁxed or movable guards, which are adjustable for a particular operation during which they remain ﬁxed.

Counter-rotating rolls

Axial flow fans

174

11.13.2

Chain and sprockets

Meshing gears

Figure 11.12

opened or removed, this must only be possible with the aid of a tool. An alternative ﬁxed guard is the distance ﬁxed guard, which does not completely enclose a hazard, but which reduces access by virtue of its dimensions and its distance from the hazard. Where perimeter-fence guards are used, the guard must follow the contours of the machinery as far as possible, thus minimizing space between the guard and the machinery. With this type of guard it is important that the safety devices and operating systems prevent the machinery being operated with the guards closed and someone inside the guard, i.e. in the danger area. Figure 11.12 shows a range of ﬁxed guards for some of the examples shown in Figure 11.10.

Range of fixed guards.

Rack and pinion gears

Pulley belts

Belt conveyor

Work equipment hazards and control They are particularly used with machine tools where some access to the dangerous part is required (e.g. drills, circular saws, milling machines) and where the clearance required will vary (e.g. with the size of the cutter in use on a horizontal milling machine or with the size of the timber being sawn on a circular saw bench) (Figure 11.13). Adjustable guards may be the only option with cutting tools, which are otherwise very difﬁcult to guard, but they have the disadvantage of requiring frequent readjustment. By the nature of the machines on which they are most frequently used, there will still be some access to the dangerous parts, so these machines must only be used by suitably trained operators. Jigs, push sticks and false tables must be used wherever possible to minimize hazards during the feeding of the work-piece. The

working area should be well lit and kept free of anything which might cause the operator to slip or trip.

Self-adjusting guard A self-adjusting guard is one which adjusts itself to accommodate, for example, the passage of material. A good example is the spring-loaded guard ﬁtted to many portable circular saws. As with adjustable guards (see above) they only provide a partial solution in that they may well still allow access to the dangerous part of the machinery. They require careful maintenance to ensure they work to the best advantage (Figure 11.14).

11.13.3

Interlocking guard

The advantages of interlocked guards are that they allow safe access to operate and maintain the machine without dismantling the safety devices. Their disadvantage stems from the constant need to ensure that they are operating correctly and designed to be fail safe. Maintenance and inspection procedures must be very strict. This is a guard which is movable (or which has a movable part) whose movement is connected with the power or control system of the machine. An interlocking guard must be so connected to the machine controls such that: ➤ until the guard is closed the interlock prevents the machinery from operating by interrupting the power medium ➤ either the guard remains locked closed until the risk of injury from the hazard has passed or opening the guard causes the hazard to be eliminated before access is possible. Figure 11.13 Adjustable guard for a rotating shaft, such as a pedestal drill.

Figure 11.14

Self-adjusting guard on a wood saw.

A passenger lift or hoist is a good illustration of these principles: the lift will not move unless the doors are closed, and the doors remain closed and locked until the lift is stationary and in such a position that it is safe for the doors to open. Special care is needed with systems which have stored energy. This might be the momentum of a heavy moving part, stored pressure in a hydraulic or pneumatic system, or even the simple fact of a part being able to move under gravity even though the power is disconnected. In these situations, dangerous movement may continue or be possible with the guard open, and these factors need to be considered in the overall design. Braking devices (to arrest movement when the guard is opened) or delay devices (to prevent the guard opening until the machinery is safe) may be needed. All interlocking systems must be designed to minimize the risk of failureto-danger and should not be easy to defeat (Figure 11.15).

175

Introduction to Health and Safety at Work

Figure 11.15

Typical sliding and hinged interlocking guards.

11.14

Other safety devices

11.14.1

Trip devices

A trip device does not physically keep people away but detects when a person approaches close to a danger point. It should be designed to stop the machine before injury occurs. A trip device depends on the ability of the machine to stop quickly and in some cases a brake may need to be ﬁtted. Trip devices can be: ➤ mechanical in the form of a bar or barrier ➤ electrical in the form of a trip switch on an actuator rod, wire or other mechanism ➤ photoelectric or other type of presence-sensing device ➤ pressure-sensitive mat. They should be designed to be self-resetting so that the machine must be restarted using the normal procedure (Figure 11.16).

11.14.2

➤ the controls should be so placed, separated and protected as to prevent spanning with one hand only, being operated with one hand and another part of the body, or being readily bridged ➤ it should not be possible to set the dangerous parts in motion unless the controls are operated within approximately 0.5 seconds of each other. Having set the dangerous parts in motion, it should not be possible to do so again until both controls have been returned to their off position ➤ movement of the dangerous parts should be arrested immediately or, where appropriate, arrested and reversed if one or both controls are released while there is still danger from movement of the parts ➤ the hand controls should be situated at such a distance from the danger point that, on releasing the controls, it is not possible for the operator to reach the danger point before the motion of the dangerous parts has been arrested or, where appropriate, arrested and reversed (Figure 11.17).

Two-handed control devices

These are devices which require the operator to have both hands in a safe place (the location of the controls) before the machine can be operated. They are an option on machinery that is otherwise very difﬁcult to guard but they have the drawback that they only protect the operator’s hands. It is therefore essential that the design does not allow any other part of the operator’s body to enter the danger zone during operation. More signiﬁcantly, they give no protection to anyone other than the operator.

176

Where two-handed controls are used, the following principles must be followed:

11.14.3

Hold-to-run control

This is a control which allows movement of the machinery only as long as the control is held in a set position. The control must return automatically to the stop position when released. Where the machinery runs at crawl speed, this speed should be kept as low as practicable. Hold-to-run controls give even less protection to the operator than two-handed controls and have the same

Work equipment hazards and control

Figure 11.16

Schematic diagram of a telescopic trip device fitted to a redial drill.

Figure 11.18 Figure 11.17 Pedestal mounted free-standing two-hand control device.

main drawback in that they give no protection to anyone other than the operator. However, along with limited movement devices (systems which permit only a limited amount of machine movement on each occasion that the control is operated and are often called ‘inching devices’), they are extremely relevant to operations such as setting, where access may well be necessary and safeguarding by any other means is difﬁcult to achieve.

11.15

Typical photocopier.

Application of safeguards to the range of machines

The application of the safeguards to the Certiﬁcate range of machines is as follows.

Office – photocopier Application of safeguards (Figure 11.18) ➤ the machines are provided with an all-enclosing case which prevents access to the internal moving, hot or electrical parts

177

Introduction to Health and Safety at Work ➤ the access doors are interlocked so that the machine is automatically switched off when gaining access to clear jams or maintain the machine. It is good practice to switch off when opening the machine ➤ internal electrics are insulated and protected to prevent contact ➤ regular inspection and maintenance should be carried out ➤ the machine should be on the PAT (portable electrical testing) schedule ➤ good ventilation in the machine room should be maintained.

Office – document shredder Application of safeguards (Figure 11.19)

➤ noise levels should be checked and the equipment perhaps placed on a rubber mat if standing on a hard reﬂective ﬂoor.

Manufacturing and maintenance – bench top grinder Application of safeguards ➤ wheel should be enclosed as much as possible in a strong casing capable of containing a burst wheel ➤ an adjustable tool rest should be adjusted as close as possible to the wheel ➤ adjustable screen should be ﬁtted over the wheel to protect the eyes of the operator. Goggles should also be worn

➤ enclosed ﬁxed guards surround the cutters with restricted access for paper only, which prevents ﬁngers reaching the dangerous parts ➤ interlocks are ﬁtted to the cutter head so that the machine is switched off when the waste bin is emptied ➤ a trip device is used to start the machine automatically when paper is fed in ➤ machine should be on PAT schedule and regularly checked ➤ general ventilation will cover most dust problems except for very large machines where dust extraction may be necessary

Figure 11.20

Typical bench-mounted grinder.

➤ only properly trained people should mount an abrasive wheel ➤ the maximum speed should be marked on the machine so that the abrasive wheel can be matched to the machine speed ➤ noise levels should be checked and attenuating screens used if necessary ➤ the machine should be on the PAT schedule and regularly checked ➤ if necessary extract ventilation should be ﬁtted to the wheel encasing to remove dust at source.

Manufacturing and maintenance – pedestal drill Application of safeguards (Figure 11.21)

Figure 11.19

178

Typical office paper shredder.

➤ motor and drive should be ﬁtted with ﬁxed guard ➤ the spindle should be guarded by an adjustable guard, which is ﬁxed in position during the work ➤ a clamp should be available on the pedestal base to secure work-pieces

Work equipment hazards and control

Figure 11.21

Typical pedestal drill.

Agricultural/horticultural – cylinder mower Application of safeguards

Figure 11.22

Typical large cylinder mower.

➤ the machine should be on the PAT schedule and regularly checked ➤ cutting ﬂuid, if used, should be contained and not allowed to get onto clothing or skin. A splash guard may be required but is unlikely ➤ goggles should be worn by the operator.

➤ machine should be designed to operate with the grass collection box in position to restrict access to the bottom blade trap. A warning sign should be ﬁtted on the machine ➤ on pedestrian-controlled machines the control handle should automatically stop the blade rotation when the operators’ hands are removed. It should take two separate actions to restart ➤ ride on machines should be ﬁtted with a device to automatically stop the blades when the operator leaves the operating position. This is normally a switch under the seat and it should be tested to ensure that it is functioning correctly and has not been defeated ➤ drives and motor should be completely encased with a ﬁxed guard ➤ the machine should only be refuelled in the open air with a cool engine, using a proper highly ﬂammable fuel container with pourer to restrict spillage. No smoking should be allowed ➤ hot surfaces like the exhaust should be covered

179

Introduction to Health and Safety at Work 1

9 7 2

10

6

4

8

5

3

Figure 11.23 Typical chain saw with rear handle. These have the rear handle projecting from the back of the saw. They are designed to always be gripped with both hands, with the right hand on the rear handle. It may be necessary to have a range of saws with different guide bar lengths available. As a general rule, choose a chainsaw with the shortest guide bar suitable for the work. 1, Hand guard with integral chain brake; 2, Exhaust outlet directed to the RHS away from the operator; 3, Chain breakage guard at bottom of rear handle; 4, Chain designed to have low kickback tendancy; 5 Rubber anti-vibration mountings; 6, Lockout for the throttle trigger; 7, Guide bar (should be protected when transporting chainsaw); 8, Bottom chain catcher; 9, PPE hand/eye/ear defender signs; 10, On/off switch.

➤ engine must only be run in the open air to prevent a build up of fumes ➤ noise levels should be checked and an improved silencer ﬁtted to the engine and, if necessary, hearing protection used ➤ hay-fever-like problems from grass cutting are difﬁcult to control. A suitable dust mask may be required to protect the user.

Agricultural/horticultural – brush cutter/strimmer Application of safeguards (Figure 11.25)

Figure 11.24 Kevlar gloves, over trousers and over shoes providing protection against chainsaw cuts. Helmet, ear and face shields protect the head. Apprentice under instruction – first felling.

180

➤ moving engine parts should be enclosed ➤ rotating shafts should be encased in a ﬁxed drive shaft cover ➤ rotating cutting head should have a ﬁxed top guard, which extends out on the user side of the machine ➤ line changes must only be done either automatically or with the engine switched off ➤ engine should only be run in the open air ➤ refuelling should only be done in the open air using a proper highly ﬂammable liquid container with pouring spout ➤ boots with steel toe cap and good grip, stout trousers and non-snagging upper garments should be worn plus hard hat ﬁtted with full face screen and safety glasses

Work equipment hazards and control ➤ if the noise levels are sufﬁciently high (normally they are with petrol driven units) suitable hearing protection should be worn ➤ low vibration characteristics should be balanced with engine power and speed of work to achieve the minimum overall vibration exposure. Handles should be of an anti-vibration type. Engines should be mounted on ﬂexible mountings. Work periods should be limited to allow recovery ➤ washing arrangements should be provided and warm impervious gloves to guard against health risks ➤ properly constructed harness should be worn which comfortably balances the weight of the machine.

➤ ➤ ➤ ➤

Agriculture/Horticulture – Chainsaw Application of safeguards (Figure 11.23) ➤ May only be operated by fully trained, ﬁt and competent people. Using chainsaws in tree work requires a relevant certiﬁcate of competence or national competence award, unless the users are undergoing such training and are adequately supervised. However, in the agricultural sector, this requirement only applies to ﬁrst-time users of a chainsaw. This means everyone working with chainsaws on or in trees should hold such a certiﬁcate or award unless: ➤ it is being done as part of agricultural operations (e.g. hedging, clearing fallen branches, pruning trees to maintain clearance for machines); and ➤ the work is being done by the occupier or their employees; and ➤ they have used a chainsaw before 5 December 1998. In any case, operators using chainsaws for any task in agriculture or any other industry must be competent under PUWER 98. Competence assessment Lantra Awards, Stoneleigh Park, Kenilworth, Warwickshire CV8 2LG, Tel: 02476 419703, Fax: 02476 411655. NPTC, Stoneleigh Park, Kenilworth, Warwickshire CV8 2LG ➤ Avoid working alone with a chainsaw. Where this is not possible, establish procedures to raise the alarm if something goes wrong. These may include: ➤ regular contact with others using either a radio or telephone ➤ someone regularly visiting the worksite ➤ carrying a whistle to raise the alarm ➤ an automatic signalling device which sends a signal at a preset time unless prevented from doing so

➤

➤

➤ checks to ensure operators return to base or home at an agreed time. Moving engine parts should be enclosed Electrical units should be double insulated and cables ﬁtted with residual current devices Must be ﬁtted with a top handle and effective brake mechanism Chainsaws expose operators to high levels of noise and hand-arm vibration which can lead to hearing loss and conditions such as vibration white ﬁnger. These risks can be controlled by good management practice including: ➤ purchasing policies for low-noise/low-vibration chainsaws (e.g. with anti-vibration mounts and heated handles) ➤ providing suitable hearing protection ➤ proper maintenance schedules for chainsaws and protective equipment ➤ giving information and training to operators on the health risks associated with chainsaws and use of personal protective equipment (PPE), etc. Proper maintenance is essential for safe use and protection against ill-health from excessive noise and vibration. The saw must be maintained in its manufactured condition with all the safety devices in efﬁcient working order and all guards in place. It should be regularly serviced by someone who is competent to do the job. Operators need to be trained in the correct chainsharpening techniques and chain and guide bar maintenance to keep the saw in safe working condition. Operators should report any damage or excessive wear from daily checks on the following: ➤ on/off switch ➤ chain brake ➤ chain catcher ➤ silencer ➤ guide bar, drive sprocket and chain links ➤ side plate, front and rear hand guards ➤ anti-vibration mounts ➤ starting cord for correct tension. Make sure petrol containers are in good condition and clearly labelled, with securely ﬁtting caps. Use containers which are specially designed for chainsaw fuelling and lubrication. Fit an auto-ﬁller spout to the outlet of a petrol container to reduce the risk of spillage from over-ﬁlling. Operators should: ➤ avoid getting dirt in the fuel system (this may cause the chainsaw to be unreliable) ➤ securely replace all ﬁller caps immediately after fuelling/oiling ➤ wipe up any spilt petrol/oil ➤ during starting and use, keep fuel containers well away from ﬁres and other sources of ignition, including the saw itself (at least 4 m is recommended).

181

Introduction to Health and Safety at Work Do not allow operators to use discarded engine oil as a chain lubricant – it is a very poor lubricant and may cause cancer if it is in regular contact with an operator’s skin. ➤ When starting the saw, operators should maintain a safe working distance from other people and ensure the saw chain is clear of obstructions. ➤ Kickback is the sudden uncontrolled upward and backward movement of the chain and guide bar towards the operator. This can happen when the saw chain at the nose of the guide bar hits an object. Kickback is responsible for a signiﬁcant proportion of chainsaw accidents, many of which are to the face and parts of the upper body where it is difﬁcult to provide protection. A properly maintained chain brake and use of low-kickback chains (safety chains) reduces the effect, but cannot entirely prevent it. Make sure operators use the saw in a way which avoids kickback by: ➤ not allowing the nose of the guide bar to accidentally come into contact with any obstruction, e.g. branches, logs, stumps ➤ not over-reaching ➤ keeping the saw below chest height ➤ keeping the thumb of the left hand around the back of the front handle ➤ using the appropriate chain speed for the material being cut. ➤ To avoid pull-in always hold the spiked bumper securely against the tree or limb ➤ To avoid push-back be alert to conditions that may cause the top of the guide bar to be pinched and do not twist the guide bar in the cut ➤ Training in good manual handling techniques and using handling aids/tools should reduce the risk of back injuries ➤ To avoid overhead and other service hazards before felling starts on the worksite: ➤ contact the owners of any overhead power lines within a distance equal to twice the height of any tree to be felled to discuss whether the lines need to be lowered or made dead ➤ do not start work until agreement has been reached on the precautions to be taken ➤ check whether there are underground services such as power cables or gas pipes which could be damaged when the tree strikes the ground ➤ if there are roads or public rights or way within a distance equal to twice the height of the tree to be felled, ensure that road users and members of the public do not enter the danger zone. You may need to arrange warning notices, diversions or trafﬁc control. Safe working practices for felling are given in HSE’s AFAG leaﬂets 300 series.

182

➤ Suitable personal protective equipment (PPE) should always be worn, no matter how small the job. European standards for chainsaw PPE are published as part of EN 381 Protective clothing for users of hand-held chainsaws. Protective clothing complying with this standard should provide a consistent level of resistance to chainsaw cut-through. Other clothing worn with the PPE should be close ﬁtting and non-snagging.

NB No protective equipment can ensure 100% protection against cutting by a handheld chainsaw.

Safety helmet – to EN 397 (arborists working from a rope and harness may use a suitable adapted rockclimbing helmet) Hearing protection – to EN 352-1. Eye protection – mesh visors to EN 1731 or safety glasses to EN 166. Upper body protection* – chainsaw jackets to BS EN 381-11 Gloves – to EN 381-7. The use of appropriate gloves is recommended under most circumstances. The type of glove will depend on a risk assessment of the task and the machine. Consider the need for protection from cuts from the chainsaw, thorny material and cold/wet conditions. Leg protection – to EN 381-5 (all-round protection is recommended for arborists working in trees, and for occasional users such as those working in agriculture) Chainsaw boots – to BS EN ISO 20345:2004 and bearing a shield depicting a chainsaw to show compliance with EN 381-3 (for occasional users working on even ground where there is little risk of tripping or snagging on undergrowth or brash, protective gaiters conforming to EN 381-9 worn in combination with steel-toe-capped safety boots) * Chainsaw jackets can provide additional protection where operators are at increased risk (e.g. trainees, unavoidable use of a chainsaw above chest height). However, this needs to be weighed against increased heat stress generated by physical exertion (e.g. working from a rope and harness)

➤ If conditions are dustry, suitable ﬁltering face masks should be worn.

Retail – compactor Application of safeguards (Figure 11.25) ➤ access doors to the loading area, which gives access to the ram, should be positively interlocked with electrical and/or hydraulic mechanisms

Work equipment hazards and control ➤ the ram pressure should be dumped if it is hydraulic ➤ drives of motors should be properly guarded ➤ if the waste unit is removed by truck, the ram mechanism should be interlocked with the unit so that it cannot operate when the unit is changed for an empty one ➤ the machine should be regularly inspected and tested by a competent person

➤ if the hydraulic ram can fall under gravity, mechanical restraints should automatically move into position when the doors are opened ➤ emergency stop buttons should be ﬁtted on each side.

Retail – checkout conveyor Application of safeguards ➤ all traps between belt and rollers are either provided with ﬁxed guards or interlocked guards ➤ motor and drive unit should be provided with a ﬁxed guard and access to underside of conveyor is prevented by enclosure ➤ adequate emergency stop buttons must be provided by the checkout operator ➤ machine should be on the PAT electrical inspection schedule and regularly checked ➤ auto stop system should be ﬁtted so that conveyor does not push products into the operator’s working zone.

Construction – cement mixer Application of safeguards (Figure 11.27)

Figure 11.25 sional users.

STIHL petrol-driven brush cutter for profes-

Figure 11.26

Typical retail compactor.

➤ operating position for the hopper hoist should be designed so that anyone in the trapping area is visible to the operator. The use of the machine should be restricted to designated operators only. As far as possible the trapping point should be designed out. The hoist operating location should be fenced off

183

Introduction to Health and Safety at Work just allowing access for barrows etc., to the unloading area ➤ drives and rotating parts of engine should be enclosed

➤ the drum gearing should be enclosed and persons kept away from the rotating drum, which is normally fairly high on large machines ➤ no one should be allowed to stand on the machine while it is in motion ➤ goggles should be worn to prevent cement splashes ➤ if petrol driven, care is required with ﬂammable liquids and refuelling ➤ engines must only be run in the open air ➤ electric machines should be regularly checked and be on the PAT schedule ➤ noise levels should be checked and noise attenuation, for example, silencers and damping, ﬁtted if necessary.

Construction – bench-mounted circular saw Application of safeguards (Figure 11.28)

Figure 11.27

Typical cement/concrete mixer.

Figure 11.28

Bench-mounted circular saw.

184

➤ a ﬁxed guard should be ﬁtted to the blade below the bench ➤ ﬁxed guards should be ﬁtted to the motor and drives ➤ an adjustable top guard should be ﬁtted to the blade above the bench which encloses as much of the blade as possible. An adjustable front section should also be ﬁtted ➤ a riving knife should be ﬁtted behind the blade to keep the cut timber apart and prevent ejection

Work equipment hazards and control ➤ noise attenuation should be applied to the machine, for example, damping, special quiet saw blades and if necessary ﬁtting in an enclosure. Hearing protection may have to be used ➤ protection against wet weather should be provided ➤ the electrical parts should be regularly checked plus all the mechanical guards ➤ extraction ventilation will be required for the wood dust and shavings ➤ suitable dust masks should be worn.

11.16

Guard construction

The design and construction of guards must be appropriate to the risks identiﬁed and the mode of operation of the machinery in question. The following factors should be considered: ➤ strength – guards should be adequate for the purpose, able to resist the forces and vibration involved, and able to withstand impact (where applicable) ➤ weight and size – in relation to the need to remove and replace the guard during maintenance ➤ compatibility with materials being processed and lubricants etc. ➤ hygiene and the need to comply with food safety regulations ➤ visibility – it may be necessary to see through the guard for both operational and safety reasons ➤ noise attenuation – guards can often be used to reduce the noise levels produced by a machine. Conversely the resonance of large undamped panels may exacerbate the noise problem ➤ enabling a free ﬂow of air – where necessary (e.g. for ventilation) ➤ avoidance of additional hazards – for example, free of sharp edges ➤ ease of maintenance and cleanliness ➤ openings – the size of openings and their distance from the dangerous parts should not allow anyone to be able to reach into a danger zone. These values can be determined by experiment or by reference to standard tables. If doing so by experiment, it is essential that the machine is ﬁrst stopped and made safe (e.g. by isolation). The detailed information on openings is contained in EN 294:1992, EN 349:1993 and EN 811:1997.

11.17

Practice NEBOSH questions for Chapter 11

1. List the main requirements of the Provision and Use of Work Equipment Regulations 1998.

2. (a) Outline a hierarchy of control measures that may be used to prevent contact with dangerous parts of machinery (b) Identify FOUR non-mechanical hazards that may be encountered on woodworking machines and outline the possible health and safety effects from exposure in EACH case. 3. In order to meet a production deadline, a supervisor instructed an employee to operate a machine, which they both knew to be defective. Giving reasons in EACH case, identify possible breaches of the Health and Safety at Work etc. Act 1974 in relation to this scenario. 4. An employee was seriously injured while operating a machine, having disabled an interlocking device. The accident was properly reported to the enforcing authority and an HSE inspector has arrived to investigate the accident. (i) Outline the powers the inspector may use in order to gather information for the investigation (ii) Giving reasons in EACH case, identify the speciﬁc health and safety legislation that the machine operator may have breached (iii) Outline the action that management may take to prevent similar accidents. 5. Identify the factors to consider when assessing the suitability of controls (including emergency controls) of an item of work equipment. 6. Outline EIGHT factors that may be important in determining the maintenance requirements for an item of work equipment. 7. Identify the factors that would help to determine the maintenance procedures for an item of work equipment. 8. Outline the measures to be taken to reduce the risk of accidents associated with the routine maintenance of machinery. 9. Outline the practical precautions that might be needed prior to the repair of a large item of process machinery. 10. A decorator uses a hand-held electric sander for the preparation of wood prior to painting. (i) Outline the checks that should be made to ensure the electrical safety of the sander (ii) Other than electricity, identify FOUR hazards associated with the use of the sander.

185

Introduction to Health and Safety at Work 11. Provide sketches to show clearly the nature of the following mechanical hazards from moving parts of machinery: (i) entanglement (ii) crushing (iii) drawing-in (iv) shear. 12. Identify: (i) TWO mechanical hazards associated with moving parts of machinery (ii) TWO non-mechanical hazards to which a machine operator may be exposed. 13. List EIGHT types of mechanical hazard associated with moving parts of machinery. 14. (a) Identify THREE mechanical hazards associated with the use of a bench-top grinder (b) Outline the precautions to be taken to minimize the risk of injury to operators of bench-top grinders. 15. Identify FOUR mechanical hazards presented by pedestal drills and outline in each case how injury may occur. 16. With reference to an accident involving an operator who comes into contact with a dangerous part of a machine, describe: (i) the possible immediate causes (ii) the possible root (underlying) causes. 17. In relation to cutting timber using a bench-mounted circular saw: (i) outline the mechanical hazards to which an operator may be exposed (ii) identify the guards and protective devices designed to prevent contact with the saw blade, and in EACH case, explain how the operator is protected. (iii) outline FOUR non-mechanical hazards presented by the operation, identifying the possible health and safety effects in EACH case.

186

18. A chainsaw is to be used to fell a tree from ground level. In relation to this task: (i) identify FOUR hazards associated with the use of the chainsaw (ii) list the items of personal protective equipment that should be used by the chainsaw operative. 19. An employee is to use a petrol-driven chainsaw to fell a tree from ground level. Outline the hazards faced by the employee in carrying out this task. 20. Identify FOUR hazards when cutting grass on roadside verges with a rider-operated motor-mower and outline the precautions to be taken in EACH one. 21. Outline the FOUR main categories of guards and safeguarding devices that may be used to minimize the risk of contact with dangerous parts of machinery. 22. (a) Describe when a ﬁxed guard would be an appropriate means of providing protection against mechanical hazards (b) Outline the features of ﬁxed guards designed to minimize the risk of injury or ill health from dangerous parts of machinery. 23. (a) In relation to machine safety, outline the principles of operation of: (i) interlocked guards (ii) trip devices. (b) Other than contact with dangerous parts, identify FOUR types of danger against which ﬁxed guards on machines may provide protection. 24. (a) Outline the principles of the following types of machine guard: (i) ﬁxed guard (ii) interlocked guard. (b) Identify TWO advantages and TWO possible disadvantages of a ﬁxed machine guard.

12

Electrical hazards and control

12.1 Introduction Electricity is a widely used, efﬁcient and convenient, but potentially hazardous method of transmitting and using energy. It is in use in every factory, workshop, laboratory and ofﬁce in the country. Any use of electricity has the potential to be very hazardous with possible fatal results. Legislation has been in place for many years to control and regulate the use of electrical energy and the activities associated with its use. Such legislation provides a framework for the standards required in the design, installation, maintenance and use of electrical equipment and systems and the supervision of these activities to minimize the risk of injury. Electrical work from the largest to the smallest installation must be carried out by people known to be competent to undertake such work. New installations always require expert advice at all appropriate levels to cover both design aspects of the system and its associated equipment. Electrical systems and equipment must be properly selected, installed, used and maintained. Approximately 8% of all fatalities at work are caused by electric shock. Over the last few years, there

Figure 12.1

Beware of electricity – typical sign.

have been between 12 and 16 employee deaths due to electricity, between 210 and 258 major accidents and about 500 over three-day accidents each year. The majority of the fatalities occur in the agriculture, extractive and utility supply and service industries, while the majority of the major accidents happen in the manufacturing, construction and service industries. Only voltages up to and including mains voltage (220/240 V) will be considered in detail in this chapter and the three principal electrical hazards – electric shock, electric burns and electrical ﬁres and explosions.

12.2 Principles of electricity and some definitions 12.2.1

Basic principles and measurement of electricity

In simple terms, electricity is the ﬂow or movement of electrons through a substance which allows the transfer of electrical energy from one position to another. The substance through which the electricity ﬂows is called a conductor. This ﬂow or movement of electrons is known as the electric current. There are two forms of electric current – direct and alternating. Direct current (dc) involves the ﬂow of electrons along a conductor from one end to the other. This type of current is mainly restricted to batteries and similar devices. Alternating current (ac) is produced by a rotating alternator and causes an oscillation of the electrons rather than a ﬂow of electrons so that energy is passed from one electron to the adjacent one and so on through the length of the conductor.

187

Introduction to Health and Safety at Work It is sometimes easier to understand the basic principles of electricity by comparing its movement with that of water in a pipe ﬂowing downhill. The ﬂow rate of water through the pipe (measured in litres/s) is similar to the current ﬂowing through the conductor which is measured in amperes, normally abbreviated to amps. Sometimes very small currents are used and these are measured in milliamps (mA). The higher the pressure drop is along the pipeline, the greater will be the ﬂow rate of water and, in a similar way, the higher the electrical ‘pressure difference’ along the conductor, the higher the current will be. This electrical ‘pressure difference’ or potential difference is measured in volts. The ﬂow rate through the pipe will also vary for a ﬁxed pressure drop as the roughness on the inside surface of the pipe varies – the rougher the surface, the slower the ﬂow and the higher the resistance to ﬂow becomes. Similarly, for electricity, the poorer the conductor, the higher the resistance is to electrical current and the lower the current becomes. Electrical resistance is measured in ohms. The voltage (V ), the current (I) and the resistance (R) are related by the following formula, known as Ohm’s law: V I R (Volts) and, electrical power (P) is given by: P V I (Watts) These basic formulae enable simple calculations to be made so that, for example, the correct size of fuse may be ascertained for a particular piece of electrical equipment.

Conductors and insulators Conductors are nearly always metals, copper being a particularly good conductor, and are usually in wire form but they can be gases or liquids, water being a particularly good conductor of electricity. Super-conductors is a term given to certain metals which have a very low resistance to electricity at low temperatures. Very poor conductors are known as insulators and include materials such as rubber, timber and plastics. Insulating material is used to protect people from some of the hazards associated with electricity.

Short circuit Electrical equipment components and an electrical power supply (normally the mains or a battery) are joined together by a conductor to form a circuit. If the circuit is broken in some way so that the current ﬂows directly to earth rather than to a piece of equipment, a short circuit is made. Since the resistance is greatly reduced but the voltage remains the same, a rapid increase in current

188

occurs which could cause signiﬁcant problems if suitable protection were not available.

Earthing The electricity supply company has one of its conductors solidly connected to the earth and every circuit supplied by the company must have one of its conductors connected to earth. This means that if there is a fault, such as a break in the circuit, the current, known as the earth fault current, will return directly to earth, which forms the circuit of least resistance, thus maintaining the supply circuit. This process is known as earthing. Other devices, such as fuses and residual current devices, which will be described later, will also be needed within the circuit to interrupt the current ﬂow to earth so as to protect people from electric shock and equipment from overheating. Good and effective earthing is absolutely essential and must be connected and checked by a competent person. Where a direct contact with earth is not possible, for example, in a motor car, a common voltage reference point is used, such as the vehicle chassis. Where other potential metallic conductors exist near to electrical conductors in a building, they must be connected to the main earth terminal to ensure equipotential bonding of all conductors to earth. This applies to gas, water and central heating pipes and other devices such as lightning protection systems. Supplementary bonding is required in bathrooms and kitchens where, for example, metal sinks and other metallic equipment surfaces are present. This involves the connection of a conductor from the sink to a water supply pipe which has been earthed by equipotential bonding. There have been several fatalities due to electric shocks from ‘live’ service pipes or kitchen sinks.

12.2.2

Some definitions

Certain terms are frequently used with reference to electricity and the more common ones are deﬁned here. Low voltage – a voltage normally not exceeding 600 V ac between conductors and earth or 1000 V ac between phases. Mains voltage falls into this category. High voltage – a voltage normally exceeding 600 V ac between conductors and earth or 1000 V ac between phases. Mains voltage – this is the common voltage available in domestic premises and many workplaces and is normally taken from three pin socket points. In the UK it is distributed by the national grid and is usually supplied between 220 V and 240 V, ac and at 50 cycles/s. Maintenance – a combination of any actions carried out to retain an item of electrical equipment in, or restore it to, an acceptable and safe condition.

Electrical hazards and control Testing – a measurement carried out to monitor the conditions of an item of electrical equipment without physically altering the construction of the item or the electrical system to which it is connected. Inspection – a maintenance action involving the careful scrutiny of an item of electrical equipment, using, if necessary, all the senses to detect any failure to meet an acceptable and safe condition. An inspection does not include any dismantling of the item of equipment. Examination – an inspection together with the possible partial dismantling of an item of electrical equipment, including measurement and non-destructive testing as required, in order to arrive at a reliable conclusion as to its condition and safety. Isolation – involves cutting off the electrical supply from all or a discrete section of the installation by separating the installation or section from every source of electrical energy. This is the normal practice so as to ensure the safety of persons working on or in the vicinity of electrical components which are normally live and where there is a risk of direct contact with live electricity. Competent electrical person – a person possessing sufﬁcient electrical knowledge and experience to avoid the risks to health and safety associated with electrical equipment and electricity in general.

12.3 Electrical hazards and injuries Electricity is a safe, clean and quiet method of transmitting energy. However, this apparently benign source of energy when accidentally brought into contact with conducting material, such as people, animals or metals, permits releases of energy which may result in serious damage or loss of life. Constant awareness is necessary to avoid and prevent danger from accidental releases of electrical energy. The principal hazards associated with electricity are: ➤ ➤ ➤ ➤ ➤ ➤

electric shock electric burns electrical ﬁres and explosions arcing portable electrical equipment secondary hazards.

12.3.1

Electric shock and burns

Electric shock is the convulsive reaction by the human body to the ﬂow of electric current through it. This sense of shock is accompanied by pain and, in more severe cases, by burning. The shock can be produced by low voltages, high voltages or lightning. Most incidents of electric shock occur when the person becomes the

route to earth for a live conductor. The effect of electric shock and the resultant severity of injury depend upon the size of the electric current passing through the body which, in turn, depends on the voltage and the electrical resistance of the skin. If the skin is wet, a shock from mains voltage (220/240 V) could well be fatal. The effect of shock is very dependent on conditions at the time but it is always dangerous and must be avoided. Electric burns are usually more severe than those caused by heat, since they can penetrate deep into the tissues of the body. The effect of electric current on the human body depends on its pathway through the body (e.g. hand to hand or hand to foot), the frequency of the current, the length of time of the shock and the size of the current. Current size is dependent on the duration of contact and the electrical resistance of body tissue. The electrical resistance of the body is greatest in the skin and is approximately 100 000 ohm, however, this may be reduced by a factor of 100 when the skin is wet. The body beneath the skin offers very little resistance to electricity due to its very high water content and, while the overall body resistance varies considerably between people and during the lifetime of each person, it averages at 1000 ohm. Skin that is wounded, bruised or damaged will considerably reduce human electrical resistance and work should not be undertaken on electrical equipment if damaged skin is unprotected. An electric current of 1 mA is detectable by touch and one of 10 mA will cause muscle contraction which may prevent the person from being able to release the conductor, and if the chest is in the current path, respiratory movement may be prevented causing asphyxia. Current passing through the chest may also cause ﬁbrillation of the heart (vibration of the heart muscle) and disrupt the normal rhythm of the heart, though this is likely only within a particular range of currents. The shock can also cause the heart to stop completely (cardiac arrest) and this will lead to the cessation of breathing. Current passing through the respiratory centre of the brain may cause respiratory arrest that does not quickly respond to the breaking of the electrical contact. These effects on the heart and respiratory system can be caused by currents as low as 25 mA. It is not possible to be precise on the threshold current because it is dependent on the environmental conditions at the time, as well as the age, sex, body weight and health of the person. Burns of the skin occur at the point of electrical contact due to the high resistance of skin. These burns may be deep, slow to heal and often leave permanent scars. Burns may also occur inside the body along the path of the electric current causing damage to muscle tissue and blood cells. Burns associated with radiation and microwaves are dealt with in Chapter 15.

189

Introduction to Health and Safety at Work 12.3.2

Treatment of electric shock and burns

There are many excellent posters available which illustrate a ﬁrst-aid procedure for treating electric shock and such posters should be positioned close to electrical junction boxes or isolation switches. The recommended procedure for treating an unconscious person who has received a low voltage electric shock is as follows: 1.

2. 3. 4.

5.

On ﬁnding a person suffering from electric shock, raise the alarm by calling for help from colleagues (including a trained ﬁrst aider) Switch off the power if it is possible and/or the position of the emergency isolation switch is known Call for an ambulance If it is not possible to switch off the power, then push or pull the person away from the conductor using an object made from a good insulator, such as a wooden chair or broom. Remember to stand on dry insulating material, for example, a wooden pallet, rubber mat or wooden box. If these precautions are not taken, then the rescuer will also be electrocuted If the person is breathing, place them in the recovery position so that an open airway is maintained and the mouth can drain if necessary

Figure 12.3

6.

7.

8. 9.

Keep 18 m clear on high voltage lines.

If the person is not breathing apply mouth-to-mouth resuscitation and, in the absence of a pulse, chest compressions. When the person is breathing normally place them in the recovery position Treat any burns by placing a sterile dressing over the burn and secure with a bandage. Any loose skin or blisters should not be touched nor any lotions or ointments applied to the burn wound If the person regains consciousness, treat for normal shock Remain with the person until they are taken to a hospital or local surgery.

It is important to note that electrocution by high voltage electricity is normally instantly fatal. On discovering a person who has been electrocuted by high voltage electricity, the police and electricity supply company should be informed. If the person remains in contact with or within 18 m of the supply, they should not be approached to within 18 m by others until the supply has been switched off and clearance has been given by the emergency services. High voltage electricity can ‘arc’ over distances less than 18 m, thus electrocuting the would-be rescuer.

12.3.3

Figure 12.2

190

Typical electric shock treatment poster.

Electrical fires and explosions

Over 25% of all ﬁres have a cause linked to a malfunction of either a piece of electrical equipment or wiring or both. Electrical ﬁres are often caused by a lack of reasonable care in the maintenance and use of electrical installations and equipment. The electricity that provides heat and light and drives electric motors is capable of igniting insulating or other combustible material if the equipment is misused, is not adequate to carry the electrical load, or is

Electrical hazards and control not properly installed and maintained. The most common causes of ﬁre in electrical installations are short circuits, overheating of cables and equipment, the ignition of ﬂammable gases and vapours, and the ignition of combustible substances by static electrical discharges. Short circuits happen, as mentioned earlier, if insulation becomes faulty, and an unintended ﬂow of current between two conductors or between one conductor and earth occurs. The amount of the current depends, among other things, upon the voltage, the condition of the insulating material and the distance between the conductors. At ﬁrst the current ﬂow will be low but as the fault develops the current will increase and the area surrounding the fault will heat up. In time, if the fault persists, a total breakdown of insulation will result and excessive current will ﬂow through the fault. If the fuse fails to operate or is in excess of the recommended fuse rating, overheating will occur and a ﬁre will result. A ﬁre can also be caused if combustible material is in close proximity to the heated wire or hot sparks are ejected. Short circuits are most likely to occur where electrical equipment or cables are susceptible to damage by water leaks or mechanical damage. Twisted or bent cables can also cause breakdowns in insulation materials. Inspection covers and cable boxes are particular problem areas. Effective steps should be taken to prevent the entry of moisture as this will reduce or eliminate the risk. Covers can themselves be a problem especially in dusty areas where the dust can accumulate on ﬂat insulating surfaces resulting in tracking between conductors at different voltages and a subsequent insulation failure. The interior of inspection panels should be kept clean and dust free by using a suitable vacuum cleaner. Overheating of cables and equipment will occur if they become overloaded. Electrical equipment and circuits are normally rated to carry a given safe current which will keep the temperature rise of the conductors in the circuit or appliance within permissible limits and avoid the possibility of ﬁre. These safe currents deﬁne the maximum size of the fuse (the fuse rating) required for the appliance. A common cause of circuit overloading is the use of equipment and cables which are too small for the imposed electrical load. This is often caused by the addition of more and more equipment to the circuit thus taking it beyond its original design speciﬁcation. In ofﬁces, the overuse of multisocket unfused outlet adaptors can create overload problems (sometimes known as the Christmas tree effect). The more modern multiplugs are much safer as they lead to one fused plug and cannot be easily overloaded (see Figure 12.4). Another cause of overloading is mechanical breakdown or wear of an electric motor and the driven machinery. Motors must be maintained in good condition with particular attention paid to bearing surfaces. Fuses do not always provide total protection against the overloading

Figure 12.4

Modern multiplug.

of motors and, in some cases, severe heating may occur without the fuses being activated. Loose cable connections are one of the most common causes of overheating and may be readily detected (as well as overloaded cables) by a thermal imaging survey (a technique which indicates the presence of hot spots). The bunching of cables together can also cause excessive heat to be developed within the inner cable leading to a ﬁre risk. This can happen with cable extension reels, which have only been partially unwound, used for high-energy appliances like an electric heater. Ventilation is necessary to maintain safe temperatures in most electrical equipment and overheating is liable to occur if ventilation is in any way obstructed or reduced. All electric equipment must be kept free of any obstructions that restrict the free supply of air to the equipment and, in particular, to the ventilation apertures. Most electrical equipment either sparks in normal operation or is liable to spark under fault conditions. Some electrical appliances such as electric heaters, are speciﬁcally designed to produce high temperatures. These circumstances create ﬁre and explosion hazards, which demand very careful assessment in locations where processes capable of producing ﬂammable concentrations of gas or vapour are used, or where ﬂammable liquids are stored. It is likely that many ﬁres are caused by static electrical discharges. Static electricity can, in general, be eliminated by the careful design and selection of materials used in equipment and plant, and the materials used in products being manufactured. When it is impractical to avoid the generation of static electricity, a means of control must be devised. Where ﬂammable materials are present, especially if they are gases or dusts, then there is a great danger of ﬁre and explosion, even if there is only a small discharge of static electricity. The control and prevention of static electricity is considered in more detail later.

191

Introduction to Health and Safety at Work The use of electrical equipment in potentially ﬂammable atmospheres should be avoided as far as possible. However, there will be many cases where electrical equipment must be used and, in these cases, the standards for the construction of the equipment should comply with the Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations 1996, known as ATEX. Details on the classiﬁcation or zoning of areas is contained in the Dangerous Substances and Explosive Atmospheres Regulations and ACOPS. Before electrical equipment is installed in any location where ﬂammable vapours or gases may be present, the area must be zoned in accordance with the Dangerous Substances and Explosive Atmosphere Regulations and records of the zoned areas must be marked on building drawings and revised when any zoned area is changed. The installation and maintenance of electrical equipment in potentially ﬂammable atmospheres is a specialized task. It must only be undertaken by electricians or instrument mechanics who are trained to ATEX standards. In the case of a ﬁre involving electrical equipment, the ﬁrst action must be the isolation of the power supply so that the circuit is no longer live. This is achieved by switching off the power supply at the mains isolation switch or at another appropriate point in the system. Where it is not possible to switch off the current, the ﬁre must be attacked in a way which will not cause additional danger. The use of a non-conducting extinguishing medium, such as carbon dioxide or powder, is necessary. After extinguishing such a ﬁre careful watch should be kept for renewed outbreaks until the fault has been rectiﬁed. Re-ignition is a particular problem when carbon dioxide extinguishers are used, although less equipment may be damaged than is the case when powder is used. Finally, the chances of electrical ﬁres occurring are considerably reduced if the original installation was undertaken by competent electricians working to recognized standards, such as the Institution of Electrical Engineers’ Code of Practice. It is also important to have a system of regular testing and inspection in place so that any remedial maintenance can take place.

12.3.4

12.3.5

Static electricity

Static electricity is produced by the build-up of electrons on weak electrical conductors or insulating materials. These materials may be gaseous, liquid or solid and may include ﬂammable liquids, powders, plastic ﬁlms and granules. The generation of static may be caused by the rapid separation of highly insulated materials by friction or by transfer from one highly charged material to another in an electric ﬁeld by induction (see Figure 12.5). Discharges of static electricity may be sufﬁcient to cause serious electric shock and are always a potential source of ignition when ﬂammable liquid, dusts or powders are present. Flour dust in a mill, for example, has been ignited by static electricity. Static electricity may build up on both materials and people. When a charged person approaches ﬂammable gases or vapours and a spark ignites the substance, the resulting explosion or ﬁre often causes serious injury. Lightning strikes are a natural form of static electricity and result in large amounts of electrical energy being

Electric arcing

A person who is standing on earth too close to a high voltage conductor may suffer ﬂash burns as a result of arc formation. Such burns may be extensive and lower the resistance of the skin so that electric shock may add to the ill effects. Electric arc faults can cause temporary blindness by burning the retina of the eye and this may lead to additional secondary hazards. The quantity of electrical energy is as important as the size of the voltage since the voltage will determine the distance over which

192

the arc will travel. The risk of arcing can be reduced by the insulation of live conductors. Strong electromagnetic ﬁelds induce surface charges on people. If these charges accumulate, skin sensation is affected and spark discharges to earth may cause localized pain or bruising. Whether prolonged exposure to strong ﬁelds has any other signiﬁcant effects on health has not been proved. However, the action of an implanted cardiac pacemaker may be disturbed by the close proximity of its wearer to a powerful electromagnetic ﬁeld. The health effects of arcing and other nonionising radiation are covered in Chapter 15.

Figure 12.5 Prevention of static discharge – container connected to earthed drum.

Electrical hazards and control dissipated in a short time in a limited space with a varying degree of damage. The current produced in the vast majority of strikes exceeds 3000 amps over a short period of time. Before a strike, the electrical potential between the cloud and earth might be about 100 million volts and the energy released at its peak might be about 100 million watts per metre of strike. The need to provide lightning protection depends on a number of factors, which include: ➤ the risk of a strike occurring ➤ the number of people likely to be affected ➤ The location of structure and the nearness of other tall structures in the vicinity ➤ the type of construction, including the materials used ➤ the contents of structure or building (including any ﬂammable substances) ➤ the value of the building and its contents. Expert advice will be required from a specialist company in lightning protection, especially when ﬂammable substances are involved. Lightning strikes can also cause complete destruction and/or signiﬁcant disruption of electronic equipment.

12.3.6

Portable electrical equipment

Portable and transportable electrical equipment is deﬁned by the Health and Safety Executive as ‘not part of a ﬁxed installation but may be connected to a ﬁxed installation by means of a ﬂexible cable and either a socket and plug or a spur box or similar means. It may be hand held or hand operated while connected to the supply, or is intended or likely to be moved while connected to the supply’. The auxiliary equipment, such as extension leads, plugs and sockets, used with portable tools is also classiﬁed as portable equipment. The term ‘portable’ means both portable and transportable. Almost 25% of all reportable electrical accidents involve portable electrical equipment (known as portable appliances). While most of these accidents were caused by electric shock, over 2000 ﬁres each year are started by faulty cables used by portable appliances, caused by a lack of effective maintenance. Portable electrical tools often present a high risk of injury, which is frequently caused by the conditions under which they are used. These conditions include the use of defective or unsuitable equipment and, indeed, the misuse of equipment. There must be a system to record the inspection, maintenance and repair of these tools.

(a) (b)

(c)

Figure 12.6

Portable hand-held electric power tools.

193

Introduction to Health and Safety at Work Where plugs and sockets are used for portable tools, sufﬁcient sockets must be provided for all the equipment and adaptors should not be used. Many accidents are caused by faulty ﬂexible cables, extension leads, plugs and sockets, particularly when these items become damp or worn. Accidents often occur when contact is made with some part of the tool which has become live (probably at mains voltage), while the user is standing on, or in contact with, an earthed conducting surface. If the electric supply is at more than 50 V ac, then the electric shock that a person may receive from such defective equipment is potentially lethal. In adverse environmental conditions, such as humid or damp atmospheres, even lower voltages can be dangerous. Portable electrical equipment should not be used in ﬂammable atmospheres if it can be avoided and it must also comply with any standard relevant to the particular environment. Air operated equipment should also be used as an alternative whenever it is practical. Some portable equipment requires substantial power to operate and may require voltages higher than those usually used for portable tools, so that the current is kept down to reasonable levels. In these cases, power leads with a separate earth conductor and earth screen must be used. Earth leakage relays and earth monitoring equipment must also be used, together with substantial plugs and sockets designed for this type of system. Electrical equipment is safe when properly selected, used and maintained. It is important, however, that the environmental conditions are always carefully considered. The hazards associated with portable appliances increase with the frequency of use and the harshness of the environment (construction sites are often particularly hazardous in this respect). These factors must be considered when inspection, testing and maintenance procedures are being developed.

12.3.7

12.4 General control measures for electrical hazards The principal control measures for electrical hazards are contained in the statutory precautionary requirements covered by the Electricity at Work Regulations, the main provisions of which are outlined in Chapter 17. They are applicable to all electrical equipment and systems found at the workplace and impose duties on employers, employees and the self-employed. The regulations cover the following topics: ➤ the design, construction and maintenance of electrical systems, work activities and protective equipment ➤ the strength and capability of electrical equipment ➤ the protection of equipment against adverse and hazardous environments ➤ the insulation, protection and placing of electrical conductors ➤ the earthing of conductors and other suitable precautions ➤ the integrity of referenced conductors ➤ the suitability of joints and connections used in electrical systems ➤ means for protection from excess current ➤ means for cutting off the supply and for isolation ➤ the precautions to be taken for work on equipment made dead ➤ working on or near live conductors ➤ adequate working space, access and lighting ➤ the competence requirements for persons working on electrical equipment to prevent danger and injury.

Secondary hazards

It is important to note that there are other hazards associated with portable electrical appliances, such as abrasion and impact, noise and vibration. Trailing leads used for portable equipment and raised socket points offer serious trip hazards and both should be used with great care near pedestrian walkways. Power drives from electric motors should always be guarded against entanglement hazards. Secondary hazards are those additional hazards which present themselves as a result of an electrical hazard. It is very important that these hazards are considered during a risk assessment. An electric shock could lead to a fall from height if the shock occurred on a scaffold or it could lead to a collision with a vehicle if the victim collapsed on to a roadway. Similarly an electrical ﬁre could lead to all the associated ﬁre hazards outlined in Chapter 13 (e.g. suffocation,

194

burns and structural collapse) and electrical burns can easily lead to infections.

Detailed safety standards for designers and installers of electrical systems and equipment are given a code of practice published by the Institution of Electrical Engineers, known as the IEE Regulations. While these regulations are not legally binding, they are recognized as a code of good practice and widely used as an industry standard. The risk of injury and damage inherent in the use of electricity can only be controlled effectively by the introduction of employee training, safe operating procedures (safe systems of work) and guidance to cover speciﬁc tasks. Training is required at all levels of the organization ranging from simple on-the-job instruction to apprenticeship for electrical technicians and supervisory courses for experienced electrical engineers. First aid training related to the need for cardiovascular resuscitation and treatment

Electrical hazards and control of electric burns should be available to all people working on electrical equipment and their supervisors. A management system should be in place to ensure that the electrical systems are installed, operated and maintained in a safe manner. All managers should be responsible for the provision of adequate resources of people, material and advice to ensure that the safety of electrical systems under their control is satisfactory and that safe systems of work are in place for all electrical equipment. (Chapter 6 gives more information on both safe systems of work and permits-to-work.) For small factories and ofﬁce or shop premises where the system voltages are normally at mains voltage, it may be necessary for an external competent person to be available to offer the necessary advice. Managers must set up a high voltage permit-to-work system for all work at and above 600 V. The system should be appropriate to the extent of the electrical system involved. Consideration should also be given to the introduction of a permit system for voltages under 600 V when appropriate and for all work on live conductors. The additional control measures that should be taken when working with electricity or using electrical equipment are summarized by the following topics:

affect process plant and equipment. These are certain to happen at some time and the design of the installation should be such that a safe shut-down can be achieved in the event of a total mains failure. This may require the use of a battery backed shut-down system or emergency stand-by electric generators (assuming that this is cost effective). Finally, it is important to stress that electrical equipment must only be used within the rating performance given by the manufacturer and any accompanying instructions from the manufacturer or supplier must be carefully followed.

➤ the selection of suitable equipment ➤ the use of protective systems ➤ inspection and maintenance strategies.

A fuse will provide protection against faults and continuous marginal current overloads. It is basically a thin strip of conducting wire which will melt when the rated current passes through it, thus breaking the circuit. A fuse rated at 13 ampere (A) will melt when a current in excess of 13 ampere (A) passes through the fuse thus stopping the ﬂow of current. A circuit breaker throws a switch off when excess current passes and is similar in action to a fuse. Protection against overload is provided by fuses which detect a continuous marginal excess ﬂow of current and energy. This overcurrent protection is arranged to operate before damage occurs, either to the supply system or to the load which may be a motor or heater. When providing protection against overload, consideration needs to be made as to whether tripping the circuit could give rise to an even more dangerous situation, such as with ﬁre-ﬁghting equipment. The prime objective of a fuse is to protect equipment or an installation from overheating and becoming a ﬁre hazard. It is not an effective protection against electric shock due to the time that it takes to cut the current ﬂow. The examination of fuses is a vital part of an inspection programme to ensure that the correct size or rating is ﬁtted at all times.

These three groups of measures will be discussed in detail.

12.5 The selection and suitability of equipment Many factors which affect the selection of suitable electrical equipment, such as ﬂammable, explosive and damp atmospheres and adverse weather conditions, have already been considered. Other issues include high or low temperatures, dirty or corrosive processes or problems associated with vegetation or animals (for example, tree roots touching and displacing underground power cables, farm animals urinating near power supply lines and rats gnawing through cables). Temperature extremes will affect, for example, the lubrication of motor bearings and corrosive atmospheres can lead to the breakdown of insulating materials. The equipment selected must be suitable for the task demanded or either it will become overloaded or running costs will be too high. The equipment should be installed to a recognized standard and capable of being isolated in the event of an emergency. It is also important that the equipment is effectively and safely earthed. Electric supply failures may

12.5.1

The advantages and limitations of protective systems

There are several different types of protective systems and techniques that may be used to protect people, plant and premises from electrical hazards, some of which, for example, earthing, have already been considered earlier in this chapter. However, only the more common types of protection will be considered here.

Fuse

Insulation Insulation is used to protect both people from electric shock, the short circuiting of live conductors and the dangers associated with ﬁre and explosions. Insulation is achieved by covering the conductor with an insulating

195

Introduction to Health and Safety at Work material. Insulation is often accompanied by the enclosure of the live conductors so that they are out of reach to people. A breakdown in insulation can cause electric shock, ﬁre, explosion or instrument damage.

Isolation The isolation of an electrical circuit involves more than ‘switching off’ the current in that the circuit is made dead and cannot be accidentally re-energized. It, therefore, creates a barrier between the equipment and the electrical supply which only an authorized person should be able to remove. When it is intended to carry out work, such as mechanical maintenance or a cleaning operation on plant or machinery, isolation of electrical equipment will be required to ensure safety during the work process. Isolators should always be locked off when work is to be done on electrical equipment. Before earthing or working on an isolated circuit, checks must be made to ensure that the circuit is dead and that the isolation switch is ‘locked off’ and clearly labelled.

Figure 12.7

Transformer, RCD and isolators.

Reduced low voltage systems When the working conditions are relatively severe either due to wet conditions or heavy and frequent usage of equipment, reduced voltage systems should be used. All portable tools used on construction sites, vehicle washing stations or near swimming pools, should operate on 110 V or less, preferably with a centre tapped to earth at 55 V. This means that while the full 110 V are available to power the tool, only 55 V are available to shock the worker. At this level of voltage, the effect of any electric shock should not be severe. For lighting, even lower voltages can be used and are even safer. Another way to reduce the voltage is to use battery (cordless) operated hand tools.

Figure 12.8 Multiplugs, extension lead and special plugs and sockets. 250 mA. The protected equipment must be properly protected by insulation and enclosure in addition to the RCD. The RCD will not prevent shock or limit the current resulting from an accidental contact, but it will ensure that the duration of the shock is limited to the time taken for the RCD to operate. The RCD has a test button which should be tested frequently to ensure that it is working properly.

Residual current devices If electrical equipment must operate at mains voltage, the best form of protection against electric shock is the residual current device (RCD). RCDs, also known as earth leakage circuit breakers, monitor and compare the current ﬂowing in the live and neutral conductors supplying the protected equipment. Such devices are very sensitive to differences of current between the live and neutral power lines and will cut the supply to the equipment in a very short period of time when a difference of only a few milliamperes occurs. It is the speed of the reaction which offers the protection against electric shock. RCDs can be used to protect installations against ﬁre since they will interrupt the electrical supply before sufﬁcient energy to start a ﬁre has been dissipated. For protection against electric shock, the RCD must have a rated residual current of 30 mA or less and an operating time of 40 milliseconds or less at a residual current of

196

Double insulation To remove the need for earthing on some portable power tools, double insulation is used. Double insulation employs two independent layers of insulation over the live conductors, each layer alone being adequate to insulate the electrical equipment safely. Since such tools are not protected by an earth, they must be inspected and maintained regularly and must be discarded if damaged. Figure 12.9 shows the symbol which is marked on double insulated portable power tools.

Figure 12.9

Double insulation sign.

Electrical hazards and control 12.6 Inspection and maintenance strategies 12.6.1

All ﬁxed electrical installations should be inspected and tested periodically by a competent person, such as a member of the National Inspection Council for Electrical Installation Contracting (NICEIC).

Maintenance strategies

Regulation 4(2) of the Electricity at Work Regulations requires that ‘as may be necessary to prevent danger, all systems shall be maintained so as to prevent so far as is reasonably practicable, such danger’. Regular maintenance is, therefore, required to ensure that a serious risk of injury or ﬁre does not result from installed electrical equipment. Maintenance standards should be set as high as possible so that a more reliable and safe electrical system will result. Inspection and maintenance periods should be determined by reference to the recommendations of the manufacturer, consideration of the operating conditions and the environment in which equipment is located. The importance of equipment within the plant, from the plant safety and operational viewpoint, will also have a bearing on inspection and maintenance periods. The mechanical safety of driven machinery is vital and the electrical maintenance and isolation of the electrically powered drives is an essential part of that safety. The particular areas of interest for inspection and maintenance are: ➤ the cleanliness of insulator and conductor surfaces ➤ the mechanical and electrical integrity of all joints and connections ➤ the integrity of mechanical mechanisms, such as switches and relays ➤ the calibration, condition and operation of all protection equipment, such as circuit breakers, RCDs and switches. Safe operating procedures for the isolation of plant and machinery during both electrical and mechanical maintenance, must be prepared and followed. All electrical isolators must, wherever possible, be ﬁtted with mechanisms which can be locked in the ‘open/off’ position and there must be a procedure to allow fuse withdrawal wherever isolators are not ﬁtted. Working on live equipment with voltages in excess of 110 V must not be permitted except where fault ﬁnding or testing measurements cannot be done in any other way. Reasons, such as the inconvenience of halting production, are not acceptable. Part of the maintenance process should include an appropriate system of visual inspection. By concentrating on a simple, inexpensive system of looking for visible signs of damage or faults, many of the electrical risks can be controlled, although more systematic testing may be necessary at a later stage.

12.6.2

Inspection strategies

Regular inspection of electrical equipment is an essential component of any preventative maintenance programme and, therefore, regular inspection is required under Regulation 4(2) of the Electricity at Work Regulations, which is quoted previously. Any strategy for the inspection of electrical equipment, particularly portable appliances, should involve the following considerations: ➤ a means of identifying the equipment to be tested ➤ the number and type of appliances to be tested ➤ the competence of those who will undertake the testing (whether in-house or bought-in) ➤ the legal requirements for portable appliance testing (PAT) and other electrical equipment testing and the guidance available ➤ organizational duties of those with responsibilities for PAT and other electrical equipment testing ➤ test equipment selection and re-calibration ➤ the development of a recording, monitoring and review system ➤ the development of any training requirements resulting from the test programme.

12.7 Portable electrical appliances testing Portable appliances should be subject to three levels of inspection – a user check, a formal visual inspection and a combined inspection and test.

12.7.1

User checks

When any portable electrical hand tool, appliance, extension lead or similar item of equipment is taken into use, and at least once each week or, in the case of heavy work, before each shift, the following visual check and associated questions should be asked: ➤ is there a recent portable appliance test (PAT) label attached to the equipment? ➤ are any bare wires visible? ➤ is the cable covering undamaged and free from cuts and abrasions (apart from light scufﬁng)? ➤ is the cable too long or too short? (Does it present a trip hazard?)

197

Introduction to Health and Safety at Work Terminal screw

EARTH WIRE green/yellow NEUTRAL WIRE blue (formerly black)

Cartridge fuse

LIVE WIRE brown (formerly red) Cable grip shoud anchor the cable covering (sheath). not the internal wires Terminals tight Correctly wired Minimum bare wire Fuse in use

Figure 12.10

Cable cover (sheath)

Cable (lead/flex)

UK standard 3-pin plug wiring.

➤ is the plug in good condition, for example, the casing is not cracked and the pins are not bent (see Figure 12.10)? ➤ are there no taped or other non-standard joints in the cable? ➤ is the outer covering (sheath) of the cable gripped where it enters the plug or the equipment? (The coloured insulation of the internal wires should not be visible) ➤ is the outer case of the equipment undamaged or loose and are all screws in place? ➤ are there any overheating or burn marks on the plug, cable, sockets or the equipment? ➤ are the trip devices (RCDs) working effectively (by pressing the ‘test’ button)?

12.7.2

Formal visual inspections and tests

There should be a formal visual inspection routinely carried out on all portable electrical appliances. Faulty equipment should be taken out of service as soon as the damage is noticed. At this inspection the plug cover (if not moulded) should be removed to check that the correct fuse is included, but the equipment itself should not be taken apart. This work can normally be carried out by a trained person who has sufﬁcient information and knowledge. Some faults, such as the loss of earth continuity due to wires breaking or loosening within the equipment, the breakdown of insulation and internal contamination (for example, dust containing metal particles may

198

cause short circuiting if it gets inside the tool), will not be spotted by visual inspections. To identify these problems, a programme of testing and inspection will be necessary. This formal combined testing and inspection should be carried out by a competent person either when there is reason to suspect the equipment may be faulty, damaged or contaminated, but this cannot be conﬁrmed by visual inspection or after any repair, modiﬁcation or similar work to the equipment, which could have affected its electrical safety. The competent person could be a person who has been speciﬁcally trained to carry out the testing of portable appliances using a simple ‘pass/fail’ type of tester. When more sophisticated tests are required, a competent person with the necessary technical electrical knowledge and experience would be needed. The inspection and testing should normally include the following checks: ➤ ➤ ➤ ➤

that the polarity is correct that the correct fuses are being used that all cables and cores are effectively terminated that the equipment is suitable for its environment.

Testing need not be expensive in many low-risk premises like shops and ofﬁces, if an employee is trained to perform the tests and appropriate equipment is purchased.

12.7.3

Frequency of inspection and testing

The frequency of inspection and testing should be based on a risk assessment which is related to the usage, type and operational environment of the equipment. The harsher the working environment is, the more frequent the period of inspection. Thus tools used on a construction site should be tested much more frequently than a visual display unit which is never moved from a desk. Manufacturers or suppliers may recommend a suitable testing period. Table 12.1 lists the suggested intervals for inspection and testing derived from HSE publications Maintaining portable and transportable electrical equipment (HSG 107 and INDG 236 and 237). It is very important to stress that there is no ‘correct’ interval for testing – it depends on the frequency of usage, type of equipment, how and where it is used. A few years ago, a young trainee was badly scalded by a boiling kettle of water which exploded while in use. On investigation, an inspection report indicated that the kettle had been checked by a competent person and passed just a few weeks before the accident. Further investigation showed that this kettle was the only method of boiling water on the premises and was in use continuously for 24 hours each day. It was therefore unsuitable for the purpose and a plumbed-in continuous-use hot water heater would have been far more suitable.

Electrical hazards and control Table 12.1

Suggested intervals for portable appliance inspection and testing

Type of business/equipment

User checks

Formal visual inspection

Combined inspection and electrical tests

Equipment hire

Yes

Before issue and after return

Before issue

Construction

Yes

Before initial use and then every month

3 months

Industrial

Yes

Before initial use and then every 3 months

6–12 months

Hotels and ofﬁces low-risk environments Batter operated (less than 20 volts)

No

No

No

Extra low voltage: (less than 50 volts ac) e.g. telephone equipment, low voltage desk lights

No

No

No

Computer/photocopiers/fax machines

No

Yes 2–4 years

No if double insulated otherwise up to 5 years

Double insulated equipment: not hand-held. Moved occasionally, e.g. fans, table lamps, slide projectors

No

Yes 2–4 years

No

Double insulated equipment: hand-held e.g. some ﬂoor cleaners, some kitchen equipment and irons

Yes

Yes 6 months–1 year

Yes 1–2 years

Earthed equipment (class 1): e.g. electric kettles, some ﬂoor cleaners, portable electric heaters

Yes

Yes 6 months–1 year

Cables (leads) and plug connected to above. Extension leads (mains voltage)

Yes

Yes 6 months–4 years depending on the type of equipment it is connected to

Yes 1–5 years depending on the type of equipment it is connected to

Note: Operational experience may demonstrate that the above intervals can be reviewed. Derived from HSE

12.7.4

Records of inspection and testing

Schedules which give details of the inspection and maintenance periods and the respective programmes, must be kept together with records of the inspection ﬁndings and the work done during maintenance. Records must include both individual items of equipment and a description of the complete system or section of the system. They should always be kept up-to-date and with an audit procedure in place to monitor the records and any required actions. The records do not have to be paper based but could be stored electronically on a computer. It is good practice to label the piece of equipment with the date of the last combined test and inspection. The effectiveness of the equipment maintenance programme may be monitored and reviewed if a record of tests is kept. It can also be used as an inventory of portable appliances and help to regulate the use of unauthorized appliances. The record will enable any

adverse trends to be monitored and to check that suitable equipment has been selected. It may also give an indication as to whether the equipment is being used correctly.

12.7.5

Advantages and limitations of portable appliance testing

The advantages of portable appliance testing include: ➤ an earlier recognition of potentially serious equipment faults, such as poor earthing, frayed and damaged cables and cracked plugs ➤ discovery of incorrect or inappropriate electrical supply and/or equipment ➤ discovery of incorrect fuses being used ➤ a reduction in the number of electrical accidents ➤ the misuse of portable appliances may be monitored ➤ equipment selection procedures can be checked

199

Introduction to Health and Safety at Work ➤ an increased awareness of the hazards associated with electricity ➤ a more regular maintenance regime should result. The limitations of portable appliance testing include: ➤ some ﬁxed equipment is tested too often leading to excessive costs ➤ some unauthorized portable equipment, such as personal kettles, are never tested since there is no record of them ➤ equipment may be misused or over-used between tests due to a lack of understanding of the meaning of the test results ➤ all faults, including trivial ones, are included on the action list so that the list becomes very long and the more signiﬁcant faults are forgotten or overlooked ➤ the level of competence of the tester can be too low ➤ the testing equipment has not been properly calibrated and/or checked before testing takes place. Most of the limitations may be addressed and the reduction in electrical accidents and injuries enables the advantages of portable appliance testing to greatly outweigh the limitations.

12.8 Practice NEBOSH questions for Chapter 12 1. In relation to electrical safety, explain the meaning of the following terms: (i) ‘isolation’ (ii) ‘earthing’ (iii) ‘reduced low voltage’ (iv) ‘overcurrent protection’.

4. In relation to the use of electrical cables and plugs in the workplace: (i) identify FOUR examples of faults and bad practices that could contribute to electrical accidents (ii) outline the corresponding precautions that should be taken for EACH of the examples identiﬁed in (i). 5. Outline a range of checks that should be made to ensure electrical safety in an ofﬁce environment. 6. A joiner has received an electric shock from a handheld 230 V drill while ﬁtting ﬂoorboards to an upstairs room of a new property. The drill is ﬁve-years-old but has not been tested during this time. The injury to the joiner was fortunately not serious. (i) Identify the factors that may have limited the severity of injury on this occasion (ii) Outline the physical effects on the body that such contact with electricity could have caused under different circumstances (iii) Outline ways of minimizing the risk of serious injury from electricity when using a portable electrical drill (iv) Describe the types of inspection and/or test to which the drill should have been subjected, identifying the particular features that should be checked by EACH type and the factors that might affect the frequencies required. 7. Outline measures that should be taken to minimize the risk of ﬁre from electrical equipment. 8. List the items that should be included on a checklist for the routine visual inspection of portable electrical appliances.

2. (a) Outline the danger associated with electricity (b) Outline the emergency action to take if a person suffers a severe electric shock.

9. With respect to the use of portable electrical appliances in the workplace, identify EIGHT examples of faults and bad practices that could contribute to electrical accidents.

3. (a) Outline the effects on the human body from a severe electric shock (b) Describe how earthing can reduce the risk of receiving an electric shock (c) Outline FOUR factors that may affect the severity of injury from contact with electricity.

10. (a) Outline the THREE levels of inspection that should be included in a maintenance and inspection strategy for portable electrical appliances (b) Identify the reasons for keeping centralized records of the results of portable appliance testing within an organization.

200

Fire hazards and control

13.1 Introduction Chapter 13 covers ﬁre prevention in the workplace and how to ensure that people are properly protected if ﬁre does occur. Each year UK ﬁre brigades attend over 35 000 ﬁres at work in which about 30 people are killed and over 2500 are injured. Fire and explosions at work account for about 2% of the major injuries reported under RIDDOR. The ﬁnancial costs associated with serious ﬁres are very high including, in many cases (believed to be over 40%), the failure to start up business again. Never underestimate the potential of any ﬁre. What may appear to be a small ﬁre in a waste bin, if not dealt with can quickly spread through a building or structure. The Bradford City Football ground in 1985 or King’s Cross Underground station in 1987 are examples of where small ﬁres quickly became raging infernos, resulting in many deaths and serious injuries. The Bunceﬁeld fuel storage depot ﬁre in December 2005 is a further recent example of the destruction which a large ﬁre and explosion can cause. Since the introduction of the Fire Services Act of 1947, the ﬁre authorities have had the responsibility for ﬁghting ﬁres in all types of premises. In 1971, the Fire Precautions Act gave the ﬁre authorities control over certain ﬁre procedures, means of escape and basic ﬁre protection equipment through the drawing up and issuing of Fire Certiﬁcates in certain categories of building. The Fire Certiﬁcation was mainly introduced to combat a number of serious industrial ﬁres that had occurred, with a needless loss of life, where simple well-planned protection would have allowed people to escape unhurt. Following a Government review in the 1990s the Fire precautions (Workplace) Regulations 1999 came into

13 force in December of that year. These regulations were made under the HSW Act. They were amended in 1999 so as to apply to a wider range of premises including those already subject to the Fire Precautions Act 1971. In many ways these Regulations established the principles of ﬁre risk assessment which would underpin a reformed legislative framework for ﬁre safety. There remained a difference of opinion within Government, as to the right home for ﬁre legislation. The Home Ofﬁce believed that process ﬁre issues should remain with the HSW Act, while general ﬁre safety should have a different legislative vehicle. In 2000 the Fire Safety Advisory Board was established to reform the ﬁre legislation to simplify, rationalize and consolidate existing legislation. It would provide for a risk-based approach to ﬁre safety allowing more efﬁcient, effective enforcement by the ﬁre and rescue service and other enforcing authorities. The Regulatory Reform (Fire Safety) Order 2005 (RRFSO) SI No 2005 1541 was made on 7 June 2005. The Order came into force on the delayed date of 1 October 2006. A summary of the Order has been included in Chapter 17. The Fire Precautions Act 1971 is repealed and The Fire Precautions (Workplace) Regulations 1997 are revoked by the Order. Since the CDM2007 Regulations were approved, the RRFSO has been amended, as the ﬁre sections within the Construction (Health, Safety and Welfare) Regulations 1997 (now revoked) have been transferred to the CDM2007. The RRFSO reforms the law relating to ﬁre safety in non-domestic premises. The main emphasis of the changes is to move towards ﬁre prevention. Fire certiﬁcates under the Fire Precautions Act 1971 are abolished by the Order and cease to have legal status. The RRFSO replaces ﬁre certiﬁcation with a general duty to ensure, so far as is reasonably practicable, the safety of employees.

201

Introduction to Health and Safety at Work There is also a general duty in relation to nonemployees to take such ﬁre precautions as may reasonably be required in the circumstances, and a duty to carry out a risk assessment to ensure that premises are safe. The Order imposes a number of speciﬁc duties in relation to the ﬁre precautions to be taken. The Order provides for the enforcement of the Order, appeals, offences and connected matters. The Order also gives effect in England and Wales to parts of a number of EC Directives including the Framework, Workplace, Chemical Agents and Explosive Atmospheres directives.

13.2 The Regulatory Reform (Fire Safety) Order 2004 (RRFSO) – Requirements

Figure 13.1

13.2.1

The meaning of general ﬁre precautions is set out, which covers:

Outline of RRFSO

Fire is still a major risk in many workplaces.

Part 1 General – The RRFSO applies to all non-domestic premises other than those listed in article 6. The main duty-holder is the ‘responsible person’ in relation to the premises, deﬁned in article 3. The duties on the responsible person are extended to any person who has, to any extent, control of the premises to the extent of their control (article 5).

➤ ➤ ➤ ➤ ➤ ➤ ➤

Part 2 imposes duties on the responsible person in relation to ﬁre safety in premises.

But does not cover process-related fire precautions. These include the use of plant or machinery or the use or storage of any dangerous substances. Process related ﬁre precautions still come under either the HSE or local authority, and are covered by the general duties imposed by the HSW Act or other speciﬁc regulations like DSEAR.

Part 3 provides for enforcement. Part 4 provides for offences and appeals. Part 5 provides for miscellaneous matters including ﬁre-ﬁghters’ switches for luminous tube signs, maintenance of measures provided to ensure the safety of ﬁreﬁghters, civil liability for breach of statutory duty by an employer, special requirements for licensed premises and consultation by other authorities. Schedule 1 sets out the matters to be taken into account in carrying out a risk assessment (Parts 1 and 2), the general principles to be applied in implementing ﬁre safety measures (Part 3) and the special measures to be taken in relation to dangerous substances (Part 4). The Order is mainly enforced by the ﬁre and rescue authorities.

13.2.2

PART 1 General

Reduction of ﬁre risks and ﬁre spread Means of escape Keeping means of escape available for use Fire ﬁghting Fire detection and ﬁre warning Action to be taken in the event of ﬁre Instruction and training of employees.

Duties Duties are placed on a ‘Responsible Person’ who is: ➤ the employer in a workplace, to the extent they have control ➤ other person who has control of the premises or ➤ the owner of the premises. The obligations of a particular responsible person relate to matters within their control. It is therefore advisable that arrangements between responsible persons, where there may be more than one (such as contracts or tenancy agreements) should clarify the division of responsibilities to avoid unnecessary breaches of the Order, where one responsible person simply assumed the other would satisfy a particular requirement.

Meanings

Premises covered

The Order deﬁnes a responsible person, as the person who may be in control of the premises – this may be the owner or somebody else.

The RRFSO does not cover domestic premises, offshore installations, a ship (normal shipboard activities under a master), remote ﬁelds, woods or other land forming part

202

Fire hazards and control of an agricultural, or forestry operation (it does cover the buildings), means of transport, a mine (it does cover the buildings at the surface), and a borehole site. Other alternative provisions cover premises such as sports grounds.

13.2.3

PART 2 fire safety duties

The responsible person must take appropriate general ﬁre precautions to protect both employees and persons who are not employees to ensure that the premises are safe. Details are given in Chapter 17.

Risk assessment and arrangements The responsible person must: ➤ make a suitable and sufﬁcient risk assessment to identify the general ﬁre precautions required (usually known as a Fire Risk assessment) ➤ if a dangerous substance is or is liable to be present, this assessment must include the special provisions of part 1 of Schedule 1 to the Order; ➤ review the risk assessment regularly or when there have been signiﬁcant changes ➤ with regard to young persons, take into account part 2 of Schedule 1 ➤ record the signiﬁcant ﬁndings where more than 4 people are employed or there is a license or Alterations Notice in place for the premises ➤ apply the principles of prevention part 3 of schedule 1 ➤ set out appropriate ﬁre safety arrangements for planning, organization, control, monitoring and review ➤ eliminate or reduce risks from dangerous substances in accordance with part 4 of schedule 1.

Fire-fighting and fire detection The responsible person must ensure that the premises are provided with appropriate: ➤ ﬁre-ﬁghting equipment ➤ ﬁre detectors and alarms ➤ measures for ﬁre-ﬁghting which are adapted to the size and type of undertaking ➤ trained and equipped competent persons to implement ﬁre-ﬁghting measures ➤ contacts with external emergency services, particularly as regards ﬁre-ﬁghting, rescue work, ﬁrst-aid and emergency medical care.

Emergency routes, exits and emergency procedures The responsible person must ensure that routes to emergency exits and the exits themselves are kept clear and

ready for use. See Chapter 17 for speciﬁc requirements for means of escape. The responsible person must establish suitable and appropriate emergency procedures and appoint a sufﬁcient number of competent persons to implement the procedures. This includes arrangements for ﬁre drill and information and action regarding exposure to serious, imminent and unavoidable dangers. Where dangerous substances are used and/or stored, additional emergency measures covering the hazards must be set up. There should be appropriate visual or audible warnings and other communications systems to effect a prompt and safe exit from the endangered area. Where necessary to protect persons’ safety all premises and facilities must be properly maintained and subject to a suitable system of maintenance.

Safety assistance The responsible person must appoint (except in the case of the self - employed or partnerships where a person has the competence themselves) one or more people to assist in undertaking the preventative and protective measures. Competent persons must be given the time and means to fulﬁl their responsibilities. Competent persons must be kept informed of anything relevant to the role and have access to information on any dangerous substances present on the premises.

Provision of information The responsible person must provide: ➤ their own employees ➤ the employer of any employees of an outside undertaking with comprehensible and relevant information on the risks, precautions taken, persons appointed for ﬁre ﬁghting and ﬁre drills, appointment of competent persons. Additional information is also required for dangerous substances used and/or stored on the premises. Before a child (16–18 years old) is employed, information on special risks to children must be given to the child’s parent or guardian.

Capabilities, training and cooperation The responsible person must ensure that adequate training is provided when people are ﬁrst employed or exposed to new or increased risks. This may occur with new equipment, changes of responsibilities, new technologies, new systems of work and new substances used. The training has to be done in working hours and repeated periodically as appropriate. Where two or more responsible persons share duties or premises they are required to coordinate their activity

203

Introduction to Health and Safety at Work and co-operate with each other, including keeping each other informed of risks.

Duties of employees These are covered in Chapter 17 and are similar to requirements under the HSW Act. Employees must take care of themselves and other relevant persons. They must co-operate with the employer and inform them of any situation which they would reasonably consider to present a serious and immediate danger, or a shortcoming in the protection arrangements.

13.2.4

PART 3 enforcement

Enforcing authorities The ﬁre and rescue authority in the area local to the premises is normally the enforcing authority. However, in standalone construction sites, premises which require a Nuclear license, and where a ship is under repair, the HSE are the enforcing authority, except for the general means of escape and ﬁre emergency procedures under CDM2007. Fire and Rescue Authorities ofﬁcers appointed under the RRFSO have similar powers to those under the HSW Act. These include the power to enter premises, make inquiries, require information, require facilities and assistance, take samples, require an article or substance to be dismantled or subjected to a process or test and the power to issue enforcement notices. In addition to ﬁre safety legislation, health and safety at work legislation also covers the elimination or minimization of ﬁre risks. As well as the particular and main general duties under the HSW Act, ﬁre risks are also covered by speciﬁc rules, such as for dangerous substances and explosive atmospheres, work equipment, electricity and other hazards. Thus, environmental health ofﬁcers or HSE inspectors may enforce health and safety standards for the assessment and removal or control of process related ﬁre risks, where it is necessary, for the protection of workers and others.

Alterations and enforcement notices Enforcing authorities can issue (See Chapter 17 for details): Alterations notices – where the premises constitute a serious risk to people either due to the features of the premises, or hazards present in the premises. The notices require the responsible person to notify changes and may require them to record the signiﬁcant ﬁndings of the risk assessment and safety arrangements; and to supply a copy of the risk assessment before making changes.

204

Enforcement notices – where there is a failure to comply with the requirements of the Order. The notice must specify the provisions concerned and MAY include directions on remedial action. Prohibition Notices – where the risks are so serious that the use of the premises should be prohibited or restricted. The notice MAY include directions on remedial action.

13.2.5

PART 4 offences

Cases can be tried on summary conviction in a magistrates court or on indictment in the Crown Court. The responsible person can be liable: ➤ on summary conviction to a ﬁne not exceeding the statutory maximum; and ➤ on indictment to an unlimited ﬁne and/or imprisonment for up to two years for failure to comply with ﬁre safety duties where there is a risk of death or serious injury and for failure to comply with an Alterations, Enforcement or Prohibition Notice. Any person who fails to comply with their duties under the Order as regards ﬁre risks can be prosecuted alongside or instead of a responsible person. Fines are limited to the statutory maximum (or levels 3 or 5 on the standard scale) on summary conviction but on indictment, the ﬁne is unlimited.

13.3 Basic principles of fire 13.3.1

Fire triangle

Fire cannot take place unless three things are present. These are shown in Figure 13.2. The absence of any one of these elements will prevent a ﬁre from starting. Prevention depends on

Fuel Flammable gases, liquids, solids

Ignition source Hot surfaces Electrical equipment Static electricity Smoking materials Naked flame

Oxygen From the air Oxidizing substances

Figure 13.2

Fire triangle.

Fire hazards and control avoiding these three coming together. Fire extinguishing depends on removing one of the elements from an existing ﬁre, and is particularly difﬁcult if an oxidizing substance is present. Once a ﬁre starts it can spread very quickly from fuel to fuel as the heat increases.

13.3.2

and clothing), wall paper, hardboard and chipboard used as building materials, waste materials (e.g. wood shavings, dust, paper, etc.), hair.

Sources of ignition

Workplaces have numerous sources of ignition, some of which are obvious but others may be hidden inside machinery. Most of the sources may cause an accidental ﬁre from sources inside but, in the case of arson (about 13% of industrial ﬁres), the source of ignition may be brought from outside the workplace and will be deliberately used. The following are potential sources of ignition in the typical workplace: ➤ naked flames – from smoking materials, cooking appliances, heating appliances and process equipment ➤ external sparks – from grinding metals, welding, impact tools, electrical switch gear ➤ internal sparking – from electrical equipment (faulty and normal), machinery, lighting ➤ hot surfaces – from lighting, cooking, heating appliances, process equipment, poorly ventilated equipment, faulty and/or badly lubricated equipment, hot bearings and drive belts ➤ static electricity – causing signiﬁcant high voltage sparks from the separation of materials such as unwinding plastic, pouring highly ﬂammable liquids, walking across insulated ﬂoors, or removing synthetic overalls.

Liquids – these include, paint, varnish, thinners, adhesives, petrol, white spirit, methylated spirits, parafﬁn, toluene, acetone and other chemicals. Most ﬂammable liquids give off vapours which are heavier than air so they will fall to the lowest levels. A ﬂash ﬂame or an explosion can occur if the vapour catches ﬁre in the correct concentrations of vapour and air.

Gases – ﬂammable gases include LPG (liqueﬁed petroleum gas in cylinders, usually butane or propane), acetylene (used for welding) and hydrogen. An explosion can occur if the air/gas mixture is within the explosive range.

13.3.4 13.3.3

Oxygen

Sources of fuel

If it will burn it can be fuel for a ﬁre. The things which will burn easily are the most likely to be the initial fuel, which then burns quickly and spreads the ﬁre to other fuels. The most common things that will burn in a typical workplace are:

Oxygen is of course provided by the air all around but this can be enhanced by wind, or by natural or powered ventilation systems which will provide additional oxygen to continue burning. Cylinders providing oxygen for medical purposes or welding can also provide an additional very rich source of oxygen.

Solids – these include, wood, paper, cardboard, wrapping materials, plastics, rubber, foam (e.g. polystyrene tiles and furniture upholstery), textiles (e.g. furnishings

In addition some chemicals such as nitrates, chlorates, chromates and peroxides can release oxygen as they burn and therefore need no external source of air.

205

Introduction to Health and Safety at Work 13.4 Methods of extinction There are four main methods of extinguishing ﬁres, which are explained as follows: ➤ cooling – reducing the ignition temperature by taking the heat out of the ﬁre – using water to limit or reduce the temperature ➤ smothering – limiting the oxygen available by smothering and preventing the mixture of oxygen and ﬂammable vapour – by the use of foam or a ﬁre blanket ➤ starving – limiting the fuel supply – by removing the source of fuel by switching off electrical power, isolating the ﬂow of ﬂammable liquids or removing wood and textiles, etc. ➤ chemical reaction – by interrupting the chain of combustion and combining the hydrogen atoms with chlorine atoms in the hydrocarbon chain for example with Halon extinguishers. (Halons have generally been withdrawn because of their detrimental effect on the environment, as ozone depleting agents).

13.5 Classification of fire Fires are classiﬁed in accordance with British Standard EN 2:1992 Classification of Fires. However for all practical purposes there are FIVE main classes of ﬁre – A, B, C, D and F, plus ﬁres involving electrical equipment. BS 7937:2000 The Specification of Portable Fire Extinguishers for Use on Cooking Oil Fires introduced the new class F. The categories based on fuel and the means of extinguishing are as follows: Class A – ﬁres which involve solid materials such as wood, paper, cardboard, textiles, furniture and plastics where there are normally glowing embers during combustion. Such ﬁres are extinguished by cooling which is achieved using water Class B – ﬁres which involve liquids or liqueﬁed solids such as paints, oils or fats. These can be further subdivided into: Class B1 – ﬁres which involve liquids that are soluble in water such as methanol. They can be extinguished by carbon dioxide, dry powder, water spray, light water and vaporizing liquids Class B2 – ﬁres which involve liquids not soluble in water, such as petrol and oil. They can be extinguished by using foam, carbon dioxide, dry powder, light water and vaporizing liquid Class C – ﬁres which involve gases such as natural Methods of extinction gas or liqueﬁed gases such as butane or propane. They can be extinguished using

206

foam or dry powder in conjunction with water to cool any containers involved or nearby Class D – ﬁres which involve metals such as aluminium or magnesium. Special dry powder extinguishers are required to extinguish these ﬁres, which may contain powdered graphite or talc Class F – ﬁres which involve high temperature cooking oils or fats in large catering establishments or restaurants Electrical fires – ﬁres involving electrical equipment or circuitry do not constitute a ﬁre class on their own, as electricity is a source of ignition that will feed a ﬁre until switched off or isolated. But there are some pieces of equipment that can store, within capacitors, lethal voltages even when isolated. Extinguishers speciﬁcally designed for electrical use like carbon dioxide or dry powder should always be used for this type of ﬁre hazard. Fire extinguishers are usually designed to tackle one or more class of ﬁre. This is discussed later.

13.6 Principles of heat transmission and fire spread Fire transmits heat in several ways, which need to be understood in order to prevent, plan escape from, and ﬁght ﬁres. Heat can be transmitted by convection, conduction, radiation and direct burning (Figure 13.3).

13.6.1

Convection

Hot air becomes less dense and rises drawing in cold new air to fuel the ﬁre with more oxygen. The heat is transmitted upwards at sufﬁcient intensity to ignite combustible materials in the path of the very hot products of combustion and ﬂames. This is particularly important inside buildings or other structures where the shape may effectively form a chimney for the ﬁre.

13.6.2

Conduction

This is the transmission of heat through a material with sufﬁcient intensity to melt or destroy the material and ignite combustible materials which come into contact or close to a hot section. Metals like copper, steel and aluminium are very effective or good conductors of heat. Other materials like concrete, brickwork and insulation materials are very ineffective or poor conductors of heat. Poor conductors or good insulators are used in ﬁre protection arrangements. When a poor conductor is also incombustible it is ideal for ﬁre protection. Care is necessary to ensure that there are no other hazards like a health problem with such materials. Asbestos is a very poor conductor of heat and is incombustible. Unfortunately, it has, of course, very severe

Fire hazards and control

Heated air rises

CONVECTION CONDUCTION

RADIATION

Decomposition and/or vaporization

Figure 13.3

Principles of heat transmission.

health problems which now far outweigh its value as a ﬁre protection material and it is banned in the UK, although still found in many buildings where it was used extensively for ﬁre protection.

13.6.3

Radiation

Often in a ﬁre the direct transmission of heat through the emission of heat waves from a surface can be so intense that adjacent materials are heated sufﬁciently to ignite. A metal surface glowing red-hot would be typical of a severe radiation hazard in a ﬁre.

13.6.4

Direct burning

This is the effect of combustible materials catching ﬁre through direct contact with ﬂames which causes ﬁre to spread, in the same way that lighting an open ﬁre, with a range of readily combustible fuels is spread within a grate.

13.6.5

Smoke spread in buildings

Where ﬁre is not contained and people can move away to a safe location there is little immediate risk to those people. However, where ﬁre is conﬁned inside buildings the ﬁre behaves differently (Figure 13.4). The smoke rising from the ﬁre gets trapped inside the space by the immediate ceiling then spreads

Figure 13.4

Fire spread in buildings.

horizontally across the space deepening all the time until the entire space is ﬁlled. The smoke will also pass through any holes or gaps in the walls, ceiling or ﬂoor and get into other parts of the building. It moves rapidly up staircases or lift wells and into any areas that are left open, or rooms which have open doors connecting to

207

Introduction to Health and Safety at Work the staircase corridors. The heat from the building gets trapped inside, raising the temperature very rapidly. The toxic smoke and gases are an added danger to people inside the building who must be able to escape quickly to a safe location.

13.7 Common causes of fire and consequences 13.7.1

Causes

The Home Ofﬁce statistics show that the causes of ﬁres in buildings, excluding dwellings, in 2001 was as shown in Figure 13.5. The total was 43 600, a rise of 4% from the previous year but below the ten-year peak of 47 900 in 1995. The majority of ﬁres occurred in: ➤ ➤ ➤ ➤ ➤

Private garages and sheds 20% (8900 ﬁres) Retail distribution 13% (5700 ﬁres) Industrial premises 10% (4500 ﬁres) Restaurants, cafes, public houses etc 8% (3400 ﬁres) Hospitals 7% (3000 ﬁres)

The sources of ignition are shown in Figure 13.6. Out of the 23 800 accidental ﬁres in 2001, it shows that cooking appliances and electrical equipment account for nearly 50% of the total. Malicious ﬁres increased by 10% up to 19 700, although this is still 12% lower than the 1994 peak of 22 400.

13.7.2

Consequences

The main consequences of ﬁre are: ➤ death – although this is a very real risk, relatively few people die in building ﬁres that are not dwellings. In 2001, 38 (6%) people died out of a total of 613 in all ﬁres. The main causes of all deaths were: ➤ Overcome by gas or smoke 46% ➤ Burns 27% ➤ Burns and overcome by gas or smoke 20% ➤ Other 7% Clearly gas and smoke are the main risks ➤ personal injury – some 2100 people were injured (12%) of total injuries in all ﬁres ➤ building damage – can be very signiﬁcant, particularly if the building materials have poor resistance to ﬁre and there is little or no built in ﬁre protection ➤ ﬂora and fauna damage – can be signiﬁcant, particularly in a hot draught or forest ﬁre ➤ loss of business and jobs – it is estimated that about 40% of businesses do not start up again after a signiﬁcant ﬁre. Many are under-or not insured and small companies often cannot afford the time and expense of setting up again when they probably still have old debts to service ➤ transport disruption – rail routes, roads and even airports are sometimes closed because of a serious ﬁre. The worst case was of course 11 September 2001 when airports around the world were disrupted

20000 18000 Malicious 16000 Faulty fuel supplies 14000

Faulty appliances and leads

12000

Misuse of equipment

10000

Chip/fat pans

8000

Playing with fire

6000

Careless handling of hot substances

4000

Placing articles too close to heat Other accidental

2000

Unspecified 0

Figure 13.5

208

Causes of fire, 1999.

Number

Fire hazards and control 7000

Smokers' materials

6000

Matches

5000 4000 3000

Cooking appliances Space heating appliances Central and water heating Blowlamps, welding and cutting

2000

Electrical distribution

1000

Other electrical appliances Other/not specified

0

Figure 13.6

Accidental fires – sources of ignition.

➤ environmental damage from the ﬁre and/or ﬁghting the ﬁre – ﬁre-ﬁghting water, the products of combustion and exploding building materials, such as asbestos cement roofs, can contaminate signiﬁcant areas around the ﬁre site.

Of these smoke and other gaseous combustion products are the most common cause of death in ﬁres. For a ﬁre to occur it needs sources of heat and fuel. If these hazards can be kept apart, removed or reduced, then the risks to people and businesses are minimized. Identify fire hazards in the workplace is the ﬁrst stage as follows:

13.8 Fire risk assessment

identify any combustibles – Most workplaces contain combustible materials. Usually, the presence of normal stock in trade should not cause concern, provided the materials are used safely and stored away from sources of ignition. Good standards of housekeeping are essential to minimize the risk of a ﬁre starting or spreading quickly.

13.8.1

General

What ﬁre precautions are needed depends on the risks. There are several methods of carrying out a ﬁre risk assessment, the one described below is based on the method contained within ‘Fire Safety An Employers’ Guide’ published jointly by the Stationery Ofﬁce and HSE Books. A systematic approach, considered in ﬁve simple stages, is generally the best practical method. The ﬁre risk assessment under the RRFSO is separate from the Risk assessment under the HSW Act Management Regulations (see Chapter 5). Later guidelines may allow a joint risk assessment in low risk premises but at the time of writing this is not clear.

13.8.2

Stage 1 – Identify fire hazards

There are ﬁve main hazards produced by ﬁre that should be considered when assessing the level of risk: ➤ ➤ ➤ ➤ ➤

oxygen depletion ﬂames and heat smoke gaseous combustion products structural failure of buildings.

The amount of combustible material in a workplace should be kept as low as is reasonably practicable. Materials should not be stored in gangways, corridors or stairways or where they may obstruct exit doors and routes. Fires often start and are assisted to spread by combustible waste in the workplace. Such waste should be collected frequently and removed from the workplace, particularly where processes create large quantities of it. Some combustible materials, such as ﬂammable liquids, gases or plastic foams, ignite more readily than others and quickly produce large quantities of heat and/ or dense toxic smoke. Ideally, such materials should be stored away from the workplace or in ﬁre-resisting stores. The quantity of these materials kept or used in the workplace should be as small as possible, normally no more than one-half day’s supply. identify any sources of heat – All workplaces will contain heat/ignition sources, some will be obvious such as cooking sources, heaters, boilers, engines, smoking

209

Introduction to Health and Safety at Work HEATERS WITH NAKED FLAMES

DRINKS FRIDGE

HEATER

W.C.

HEATER

PAPERS & FANCY GOODS ETC.

DISPLAY WITH POSSIBLE LIGHTERS ON CARDS

PERSONS ESPECIALLY AT RISK

STORAGE & TEA AREA

SHELVES

C O U N T E R

NEWSPAPER RACK

SHOULD A FIRE OCCUR IN THE SERVING AREA THIS PERSON MAY BE TRAPPED BY THE FIRE

LOOSE PAPER ETC. GAS COOKER WITH NAKED FLAMES TO WARM FOOD

Figure 13.7

Simple line diagram to identify fire hazards.

materials or heat from processes, whether in normal use or through carelessness or accidental failure. Others may be less obvious such as heat from chemical processes or electrical circuits and equipment. The potential for an arson attack must be considered. Where possible, sources of ignition should be removed from the workplace or replaced with safer forms. Where this cannot be done the ignition source should be kept well away from combustible materials or made the subject of management controls. Particular care should be taken in areas where portable heaters are used or where smoking is permitted (now banned inside premises). Where heat is used as part of a process, it should be used carefully to reduce the chance of a ﬁre as much as possible. Good security both inside and outside the workplace will help to combat the risk of arson. identify any unsafe acts – Persons undertaking unsafe acts such as smoking next to combustible materials, etc. identify any unsafe conditions – These are hazards that may assist a ﬁre to spread in the workplace, e.g. if there are large areas of hardboard or polystyrene tiles etc., or open stairs that can cause a ﬁre to spread quickly, trapping people and involving the whole building. An ideal method of identifying and recording these hazards is by means of a simple single line plan, an example of which is illustrated in Figure 13.7. Checklists may also be used.

the risk(s) identiﬁed will not be signiﬁcant, and speciﬁc measures for persons in this category will not be required. There will, however, be some occasions when certain people may be especially at risk from the ﬁre, because of their speciﬁc role, disability, sleeping, location or the workplace activity. Special consideration is needed if: ➤ sleeping accommodation is provided ➤ persons are physically, visually challenged ➤ people are unable to react quickly ➤ persons are isolated.

or

mentally

People, such as visitors, the public or other workers, may come into the workplace from outside. The assessor must decide whether the current arrangements are satisfactory or if changes are needed. Because ﬁre is a dynamic event, which, if unchecked, will spread throughout the workplace, all people present will eventually be at risk if ﬁre occurs. Where people are at risk, adequate means of escape from ﬁre should be provided together with arrangements for detecting and giving warning of ﬁre. Fire-ﬁghting equipment suitable for the hazards in the workplace should be provided. Some people may be at signiﬁcant risk because they work in areas where ﬁre is more likely or where rapid ﬁre growth can be anticipated. Where possible, the hazards creating the high level of risk should be reduced. Speciﬁc steps should be taken to ensure that people affected are made aware of the danger and the action they should take to ensure their safety and the safety of others.

13.8.3 Stage 2 – Identify location and persons who are at significant risk

13.8.4

Consider the risk to any people who may be present. In many instances and particularly for most small workplaces

If the building has been built and maintained in accordance with Building Regulations and is being put to its

210

Stage 3 – Reduce the risks

Fire hazards and control designed use, it is likely that the means of escape provisions will either be adequate, or it will be easy to decide what is required in relation to the risk. Having identiﬁed the hazards, the next stage is to reduce the chance of a ﬁre occurring and spreading, thereby minimizing the chance of harm to persons in the workplace. The principles of prevention laid down in the RRFSO should be followed at this stage (see section 17.17.5). These are based on EC Directive requirements and are therefore the same as those used in the Management Regulations. See Chapter 6.

or more people are employed, or an Alterations Notice required, a formal record of the signiﬁcant ﬁndings and any measures proposed to deal with them must be recorded. See summary of the Order in section 17.17. The record should indicate: ➤ ➤ ➤ ➤

the date the assessment was made the hazards identiﬁed any staff and other people especially at risk what action needs to be taken, and by when (action plan) ➤ the conclusions arising.

Evaluate the risks Attempt to classify each area as ‘high’, ‘normal’ or ‘low risk’. If ‘high risk’, it may be necessary to reconsider the principles of prevention, otherwise additional compensatory measures will be required. Low risk – Areas where there is minimal risk to persons lives, where the risk of ﬁre occurring is low, or the potential for ﬁre, heat and smoke spreading is negligible and people would have plenty of time to react to an alert of ﬁre. Normal risk – Areas will account for nearly all parts of most workplaces; where an outbreak of ﬁre is likely to remain conﬁned or spread slowly, with an effective ﬁre warning allowing persons to escape to a place of safety. High risk – Areas where the available time needed to evacuate the area is reduced by the speed of development of a ﬁre, e.g. highly ﬂammable or explosive materials stored or used (other than small quantities under controlled conditions). Also where the reaction time to the ﬁre alarm is slower because of the type of person present or the activity in the workplace, e.g. the inﬁrm and elderly or persons sleeping on the premises. Determine if the existing arrangements are adequate, or need improvement. Matters that will have to be considered are: ➤ means for detecting and giving warning in case of ﬁre – can it be heard by all occupants? ➤ means of escape – are they adequate in size, number, location, well lit, unobstructed, safe to use, etc.? ➤ signs – for exits, ﬁre routines, etc. ➤ ﬁreﬁghting equipment – wall mounted by Exits, suitable types for hazards present and sufﬁcient in number?

13.8.5 Stage 4 – The findings (always recommended, see stage 5 review) The ﬁndings of the assessment and the actions (including maintenance) arising from it should be recorded. If ﬁve

The above guidelines are to be used with caution. Each part of the workplace must be looked at and a decision made on how quickly persons would react to an alert of ﬁre in each area. Adequate safety measures will be required if persons are identiﬁed as being at risk. Where maximum travel distances (see later) cannot be achieved, extra ﬁre safety precautions will be needed. Where persons are at risk or an unacceptable hazard still exists, additional ﬁre safety precautions will be required to compensate for this, or alternatively repeat previous stages to manage risk to an acceptable level.

13.8.6

Stage 5 – Monitor and review on a regular basis

The ﬁre risk assessment is not a one-off procedure. It should be continually monitored to ensure that the existing ﬁre safety arrangements and risk assessment remains realistic. The assessment should be reviewed if there is a signiﬁcant change in the occupancy, work activity, the materials used or stored when building works are proposed, or when it is no longer thought to be valid.

13.8.7

Structural features

The workplace may contain features that could promote the rapid spread of ﬁre, heat or smoke and affect escape routes. These features may include ducts or ﬂues, openings in ﬂoors or walls, or combustible wall or ceiling linings. Where people are put at risk from these features, appropriate steps should be taken to reduce the potential for rapid ﬁre spread by, for example, non-combustible automatic dampers ﬁtted in ducts or to provide an early warning of ﬁre so that people can leave the workplace before their escape routes become unusable. Combustible wall or ceiling linings should not be used on escape routes and large areas should be removed wherever they are found. Other holes in ﬁre resisting ﬂoors, walls or ceilings should be ﬁlled in with ﬁre resisting material to prevent the passage of smoke, heat and ﬂames.

211

Introduction to Health and Safety at Work 13.8.8

Maintenance and refurbishment

Sources of heat or combustible materials may be introduced into the workplace during periods of maintenance or refurbishment. Where the work involves the introduction of heat, such as welding, this should be carefully controlled by a safe system of work, for example, a Fire Permit (see Chapter 6 for details). All materials brought into the workplace in connection with the work being carried out should be stored away from sources of heat and not obstruct exit routes.

13.8.9

Fire plans

Fire plans should be produced and attached to the risk assessment. A copy should be posted in the workplace. A single line plan of the area or ﬂoor should be produced or an existing plan should be used which needs to show: ➤ escape routes, numbers of exits, number of stairs, ﬁre resisting doors, ﬁre resisting walls and partitions, places of safety, and the like ➤ ﬁre safety signs and notices including pictorial ﬁre exit signs and ﬁre action notices ➤ the location of ﬁre warning call points and sounders or rotary gongs ➤ the location of emergency lights ➤ the location and type of ﬁre-ﬁghting equipment.

13.9 Dangerous substances 13.9.1

Introduction

The Regulations give a detailed deﬁnition of ‘dangerous substance’, which should be referred to for more information. They include any substance or preparation which, because of its properties or the way it is used, could be harmful because of ﬁres and explosions. The list includes petrol, liqueﬁed petroleum gas (LPG), paints, varnishes, solvents and some dusts. These are dusts which, when mixed with air, can cause an explosive atmosphere. Dusts from milling and sanding operations are examples of this. Most workplaces contain a certain amount of dangerous substances. An explosive atmosphere is an accumulation of gas, mist, dust or vapour, mixed with air, which has the potential to catch ﬁre or explode. Although an explosive atmosphere does not always result in an explosion (detonation), if it catches ﬁre, ﬂames can quickly travel through the workplace. In a conﬁned space (e.g. in plant or equipment) the rapid spread of the ﬂame front or rise in pressure can itself cause an explosion and rupture of the plant and/or building. For a detailed summary of the Regulations see Chapter 17.

13.9.2

Risk assessment

This is the process of identifying and carefully examining the dangerous substances present or likely to be present in the workplace, the work activities involving them and how they might fail and cause ﬁre, explosion and similar events that could harm employees and the public. The purpose of a risk assessment is to enable the employer to decide what needs to be done to eliminate or reduce the safety risks from dangerous substances as far as is reasonably practicable. It should take account of the following:

The Dangerous Substances and Explosive Atmosphere Regulations (DSEAR) applies at most workplaces where a dangerous substance is present or could be present. The employer must:

➤ what hazardous properties the substance has ➤ the way they are used and stored ➤ the possibility of hazardous explosive atmospheres occurring ➤ any potential ignition sources.

➤ carry out a risk assessment of any work activities involving dangerous substances ➤ provide a way of eliminating or reducing risks as far as is reasonably practicable ➤ provide procedures and equipment to deal with accidents and emergencies ➤ provide training and information to employees ➤ classify places where explosive atmospheres may occur into zones and mark the zones where necessary. ( This duty is being phased in see table on page 9 of Fire and explosion how safe is your workplace? DSEAR)

Regardless of the quantity of dangerous substance present, the employer must carry out a risk assessment. This will enable them to decide whether existing measures are sufﬁcient or whether they need to make any additional controls or precautions. Non-routine activities need to be assessed as well as the normal activities within the workplace. For example, in maintenance work, there is often a higher potential for ﬁre and explosion incidents to occur. Unless the employer has already carried out a detailed assessment under the Management Regulations, there must be an assessment of the risks from ﬁre,

212

Fire hazards and control explosion and other events arising from dangerous substances, including addressing requirements speciﬁed by DSEAR. Employers are required to ensure that the safety risks from dangerous substances are eliminated or, whether this is not reasonably practicable, to take measures to control risks and to reduce the harmful effects of any ﬁre, explosion or similar events, so far as is reasonably practicable (i.e. mitigation).

13.9.3

Substitution

Substitution is the best solution. It is much better to replace a dangerous substance with a substance or process that totally eliminates the risk. In practice this is difﬁcult to achieve so it is more likely that the dangerous substance will be replaced with one that is less hazardous (e.g. by replacing a low-ﬂashpoint solvent with a high-ﬂashpoint one). Designing the process so that it is less dangerous is an alternative solution. For example, a change could be made from a batch production to a continuous production process; or the manner or sequence in which the dangerous substance is added could be altered. However, care must be taken when carrying out these steps to make sure that no other new safety or health risks are created or increased, as this would outweigh the improvements implemented as a result of DSEAR. The fact is, that where a dangerous substance is handled or stored for use as a fuel, there is often no scope to eliminate it and very little chance to reduce the quantities handled. Where risk cannot be entirely eliminated, control and mitigation measures should be applied. This should reduce risk as follows.

13.9.4

Control measures

Control measures should be applied in the following order of priority: ➤ reduce the amount of dangerous substances to a minimum ➤ avoid or minimize releases ➤ control releases at source ➤ prevent the formation of an explosive atmosphere ➤ use a method such as ventilation to collect, contain and remove any releases to a safe place ➤ avoid ignition sources ➤ avoid adverse conditions (e.g. exceeding the limits of temperature or other control settings) that could lead to danger ➤ keep incompatible substances apart.

13.9.5

Mitigation measures

Choose mitigation measures, which are consistent with the risk assessment and appropriate to the nature of the activity or operation. These can include: ➤ preventing ﬁres and explosions from spreading to other plant and equipment or to other parts of the workplace ➤ making sure that a minimum number of employees is exposed ➤ in the case of a process plant, providing plant and equipment that can safely contain or suppress an explosion, or vent it to a safe place. In workplaces where explosive atmospheres may occur you should ensure that: ➤ areas where hazardous explosive atmospheres may occur are classiﬁed into zones based on their likelihood and persistence ➤ areas classiﬁed into zones are protected from sources of ignition by selecting equipment and protective system meeting the requirements of the Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations 1996 although, equipment already in use before July 2003 can continue to be used indefinitely provided to risk assessment shows it is safe to do so; ➤ where necessary, areas classiﬁed into zones are marked with a speciﬁed “EX” sign at their points of entry ➤ employees working in zoned areas must be provided with appropriate clothing that does not create a risk of an electrostatic discharge igniting the explosive atmosphere ➤ before coming into operation for the ﬁrst time, areas where hazardous explosive atmosphere may be present are conﬁrmed as being safe (veriﬁed) by a person (or organization) competent in the ﬁeld of explosion protection. The person carrying out the veriﬁcation must be competent to consider the particular risks at the workplace and the adequacy of control and other measures put in place.

13.9.6

Storage

Dangerous Substances should be kept in a safe place in a separate building or the open air. For ﬂammable liquids that have a ﬂashpoint above the maximum ambient temperature (normally taken as 32ºC), this small quantity that may be stored in the workroom is considered to be an amount up to 250 litres. For extremely and highly ﬂammable liquids, and those ﬂammable liquids with a ﬂashpoint below the maximum

213

Introduction to Health and Safety at Work ➤ kept clear of combustible materials such as cardboard or foam plastic packaging materials.

13.9.7

Flammable gases

Flammable gas cylinders also need to be stored and used safely. The following guidance should be adopted:

Figure 13.8 Various storage arrangement for highly flammable liquids.

ambient temperature, the small quantity is considered to be up to 50 litres and this should be held in a special metal cupboard or container. (Figure 13.8). Any larger amounts should be kept in special ﬁreresisting store, which should be:

➤ both full and empty cylinders should be stored outside. They should be kept in a separate secure compound at ground level with sufﬁcient ventilation. Open mesh is preferable ➤ valves should be uppermost during storage to retain them in the vapour phase of the LPG ➤ cylinders must be protected from mechanical damage. Unstable cylinders should be together, for example and cylinders must be protected from the heat of the summer sun ➤ the correct ﬁttings must be used. These include hose, couplers, clamps and regulators ➤ gas valves must be turned off after use at the end of the shift ➤ precautions must be taken against to avoid welding ﬂame ‘ﬂash back’ into the hoses or cylinders. People need training in the proper lighting up and safe systems of work procedures; non-return valves and ﬂame arrestors also need to be ﬁtted ➤ cylinders must be changed in a well-ventilated area remote from any sources of ignition ➤ joints should be tested for gas leaks using soapy/ detergent water – never use a ﬂame ➤ ﬂammable material must be removed or protected before welding or similar work ➤ cylinders should be positioned outside buildings with gas piped through in ﬁxed metal piping ➤ both high and low ventilation must be maintained where LPG application are being used ➤ ﬂame failure devices are necessary to shut off the gas supply in the event of ﬂame failure.

13.10 ➤ properly ventilated ➤ provided with spillage retaining arrangement such as sills ➤ free of sources of ignition, such as unprotected electrical equipment, sources of static electrical sparks, naked ﬂames or smoking materials ➤ arranged so that incompatible chemicals do not become mixed together either in normal use or in a ﬁre situation ➤ of ﬁre resisting construction ➤ used for empty as well as full containers – all containers must be kept closed

214

Fire detection and warning

In the event of ﬁre it is vital that everyone in the workplace is alerted as soon as possible. The earlier the ﬁre is discovered, the more likely it is that people will be able to escape before the ﬁre takes hold and before it blocks escape routes or makes escape difﬁcult. Every workplace should have detection and warning arrangements. Usually the people who work there will detect the ﬁre and in many workplaces nothing further will be needed. It is important to consider how long a ﬁre is likely to burn before it is discovered. Fires are likely to be

Fire hazards and control accommodation for fewer than six people, interlinked domestic smoke alarms (wired to the mains electricity supply) can be used provided that they are audible throughout the workplace while people are present.

Figure 13.9 Typical fire point in offices with extinguishers, fire notice and alarm break-glass call point.

discovered quickly if they occur in places that are frequently visited by employees, or in occupied areas of a building. For example, employees are likely to smell burning or see smoke if a ﬁre breaks out in an ofﬁce. Where there is concern that ﬁre may break out in an unoccupied part of the premises, for example, in a basement, some form of automatic ﬁre detection should be ﬁtted. Commercially available heat or smoke detection systems can be used. In small premises a series of interlinked domestic smoke alarms that can be heard by everyone present will be sufﬁcient. In most cases, staff can be relied upon to detect a ﬁre. In small workplaces where occupancy is low, a shouted warning should be all that is needed, so long as the warning can be heard and understood everywhere on the premises. If the size or occupancy of a workplace means that a shouted warning is insufﬁcient, hand-operated devices such as bells, gongs or sirens can be used. They should be installed on exit routes and should be clearly audible throughout the workplace. In all other places an electrically operated ﬁre alarm system should be ﬁtted. This will have call points adjacent to exit doors and enough bells or sounders to be clearly audible throughout the premises. If it is thought that there might be some delay in ﬁre being detected, automatic ﬁre detection should be considered, linked into an electrical ﬁre alarm system. Where a workplace provides sleeping accommodation or where ﬁres may develop undetected, automatic detection must be provided. If a workplace provides sleeping

13.11

Means of escape in case of fire

13.11.1

General

It is essential to ensure that people can escape quickly from a workplace if there is a ﬁre. Normally the entrances and exits to the workplace will provide escape routes, particularly if staff have been trained in what to do in case of ﬁre and if it is certain that an early warning will be given. In modern buildings which have had Building Regulation approval, and where there have not been signiﬁcant changes to the building or where the workplace has recently been inspected by the ﬁre authorities and found to be satisfactory, it is likely that the means of escape will be adequate. It may occasionally be necessary to improve the ﬁre protection on existing escape routes, or to provide additional exits. In making a decision about the adequacy of means of escape, the following points should be considered: ➤ people need to be able to turn away from a ﬁre as they escape or be able to pass a ﬁre when it is very small ➤ if a single-direction escape route is in a corridor, the corridor may need to be protected from ﬁre by ﬁreresisting partitions and self-closing ﬁre doors ➤ stair openings can act as natural chimneys in ﬁres. This makes escape from the upper parts of some workplaces difﬁcult. Most stairways, therefore, need to be separated from the workplace by ﬁre-resisting partitions and self-closing ﬁre doors. Where stairways serve no more than two open areas, in shops for example, which people may need to use as escape routes, there may be no need to use this type of protection.

13.11.2

Doors

Some doors may need to open in the direction of travel, such as: ➤ doors from a high-risk area, such as a paint spraying room or large kitchen ➤ doors that may be used by more than 50 persons ➤ doors at the foot of stairways where there may be a danger of people being crushed

215

Introduction to Health and Safety at Work ➤ some sliding doors may be suitable for escape purposes provided that they do not put people using them at additional risk, slide easily and are marked with the direction of opening ➤ doors which only revolve and do not have hinged segments are not suitable as escape doors.

checked to ensure doors close fully, including those ﬁtted with automatic release mechanisms. The maximum advisable travel distances from any area in a workplace to a ﬁre exit door leading out to a relative place of safety should be in accordance with the Table 13.1.

13.11.3

13.11.4

Escape routes

Escape routes should meet the following criteria: ➤ where two or more escape routes are needed they should lead in different directions to places of safety ➤ escape routes need to be short and to lead people directly to a place of safety, such as the open air or an area of the workplace where there is no immediate danger ➤ it should be possible for people to reach the open air without returning to the area of the ﬁre. They should then be able to move well away from the building ➤ escape routes should be wide enough for the volume of people using them. A 750 mm door will allow up to 40 people to escape in one minute, so most doors and corridors will be wide enough. If the routes are likely to be used by people in wheelchairs, the minimum width will need to be 800 mm. While the workplace is in use, it must be possible to open all doors easily and immediately from the inside, without using a doors must readily be escape. Make sure that on the ﬂoor. Fire doors should be self-closing (ﬁre doors to cupboards or lockers can be simply latched or locked). Make sure that there are no obstructions on escape routes, especially on corridors and stairways where people who are escaping could dislodge stored items or be caused to trip. Any ﬁre hazards must be removed from exit routes as a ﬁre on an exit route could have very serious consequences. Escape routes need regular checks to make sure that they are not obstructed and that exit doors are not locked. Self-closing ﬁre-resisting doors should be

Lighting

Escape routes must be well lit. If the route has only artiﬁcial lighting or if it is used during the hours of darkness, alternative sources of lighting should be considered in case the power fails during a ﬁre. Check the routes when it is dark as, for example, there may be street lighting outside that provides sufﬁcient illumination. In small workplaces it may be enough to provide the staff with torches that they can use if the power fails. However, it may be necessary to provide battery operated emergency lights so that if the mains lighting fails the lights will operate automatically. Candles, matches and cigarette lighters are not adequate forms of emergency lighting.

13.11.5

Signs

Exit signs on doors or indicating exit routes should be provided where they will help people to ﬁnd a safe escape route. Signs on exit routes should have directional arrows, ‘up’ for straight on and ‘left, right or down’ according to the route to be taken. Advice on the use of all signs including exit signs can be found in an HSE publication, Safety Signs and Signals, available from HSE Books.

13.11.6

Escape times

Everyone in the building should be able to get to the nearest place of safety in between 2 and 3 minutes. This

Table 13.1 Maximum Travel Distances* (Measured to a relative place of safety)

Low Fire Risk

Normal Risk – Production Areas (Factory Only)

Normal Fire Risk

Normal Fire Risk Sleeping

High Fire Risk

More than one route is provided

60 m

45 m

45 m

32 m

25 m

Only a single escape route is provided

45 m

25 m

18 m

16 m

12 m

*To an exit (open air where persons can disperse safely) storey exit (staircase separated from the remainder of the premises by ﬁre resisting walls and self closing ﬁre doors, etc) or a compartment wall (ﬁre resisting wall and self closing ﬁre doors).

216

Fire hazards and control means that escape routes should be kept short. Where there is only one means of escape, or where the risk of ﬁre is high, people should be able to reach a place of safety, or a place where there is more than one route available, in one minute. The way to check this is to pace out the routes, walking slowly and noting the time. Start from where people work and walk to the nearest place of safety. Remember that the more people there are using the route, the longer they will take. People take longer to negotiate stairs and they are also likely to take longer if they have a disability. Where ﬁre drills are held, check how long it takes to evacuate each ﬂoor in the workplace. This can be used as a basis for assessment. If escape times are too long, it may be worth re-arranging the workplace so that people are closer to the nearest place of safety, rather than undertake expensive alterations to provide additional escape routes. Reaction time needs to be considered. This is the amount of time people will need for preparation before they escape. It may involve, for example, closing down machinery, issues of security or helping visitors or members of the public out of the premises. Reaction time needs to be as short as possible to reduce risk to staff. Assessment of escape routes should include this. If reaction times are too long, additional routes may need to be provided. It is important that people know what to do in case of ﬁre as this can speed up the time needed to evacuate the premises.

13.12

Principles of fire protection in buildings

13.12.1

General

The design of all new buildings and the design of extensions or modiﬁcations to existing buildings must be approved by the local planning authority. Design data for new and modiﬁed buildings must be retained throughout the life of the structure. Building Legislation Standards are concerned mainly with safety to life. Therefore, it is necessary to consider the early stage of ﬁre and how it affects the means of escape, and also aim to prevent eventual spread to other buildings. Asset protection requires extra precautions that will have an effect at both early and later stages of the ﬁre growth by controlling ﬁre spread through and between buildings and preventing structural collapse. However, this extra ﬁre protection will also improve life safety not only for those escaping at the early stages of the ﬁre but also for ﬁre ﬁghters who will subsequently enter.

If a building is carefully designed and suitable materials are used to build it and maintain it, then the risk of injury or damage from ﬁre can be substantially reduced. Three objectives must be met: ➤ it must be possible for everyone to leave the building quickly and safely ➤ the building must remain standing for as long as possible ➤ the spread of ﬁre and smoke must be reduced. These objectives can be met through the selection of materials and design of buildings.

13.12.2

Fire loading

The ﬁre load of a building is used to classify types of building use. It may be calculated simply by multiplying the weight of all combustible materials by their energy values and dividing by the ﬂoor area under consideration. The higher the ﬁre load, the more the effort needed to offset this by building to higher standards of ﬁre resistance.

13.12.3

Surface spread of fire

Combustible materials, when present in a building as large continuous areas, such as for lining walls and ceilings, readily ignite and contribute to spread of ﬁre over their surfaces. This can represent a risk to life in buildings, particularly where walls of ﬁre escape routes and stairways are lined with materials of this nature. Materials are tested by insurance bodies and ﬁre research establishments. The purpose of the tests is to classify materials according to the tendency for ﬂame to spread over their surfaces. As with all standardized test methods, care must be taken when applying test results to real applications.

Figure 13.10 a fire.

Steel structures will collapse in the heat of

217

Introduction to Health and Safety at Work In the UK, a material is classiﬁed as having a surface in one of the following categories: ➤ ➤ ➤ ➤

Class 1 – Surface of very low ﬂame spread Class 2 – Surface of low ﬂame spread Class 3 – Surface of medium ﬂame spread Class 4 – Surface of rapid ﬂame spread.

The test shows how a material would behave in the initial stages of a ﬁre. As all materials tested are combustible, in a serious ﬁre they would burn or be consumed. Therefore, there is an additional Class 0 of materials which are noncombustible throughout or, under speciﬁed conditions, noncombustible on one face and combustible on the other. The spread of ﬂame rating of the combined Class 0 product must not be worse than Class 1. Internal partitions of walls and ceilings should be Class 0 materials wherever possible and must not exceed Class 1.

13.12.4

Fire resistance of structural elements

If elements of construction such as walls, ﬂoors, beams, columns and doors are to provide effective barriers to ﬁre spread and to contribute to the stability of a building, they should be of a required standard of ﬁre resistance. In the UK, tests for ﬁre resistance are made on elements of structure, full size if possible, or on a representative portion having minimum dimensions of 3 m long for columns and beams and 1 m2 for walls and ﬂoors. All elements are exposed to the same standard ﬁre provided by furnaces in which the temperature increases with time at a set rate. The conditions of exposure are appropriate to the element tested. Freestanding columns are subjected to heat all round, and walls and ﬂoors are exposed to heat on one side only. Elements of structure are graded by the length of time they continue to meet three criteria: ➤ the element must not collapse ➤ the element must not develop cracks through which ﬂames or hot gases can pass ➤ the element must have enough resistance to the passage of heat so the temperature of the unexposed face does not rise by more than a prescribed amount. The term ﬁre resistance has a precise meaning. It should not be applied to such properties of materials as resistance to ignition or resistance to ﬂame propagation. For example, steel has a high resistance to ignition and ﬂame propagation but will distort quickly in a ﬁre and

218

allow the structure to collapse – it therefore has poor ‘Fire Resistance’. It must be insulated to provide good ﬁre protection. This is normally done by encasing steel frames in concrete. In the past, asbestos has been made into a paste and plastered onto steel frames, giving excellent ﬁre protection, but it has caused major health problems and its use in new work is banned. Building materials with high ﬁre resistance are, for example, brick, stone, concrete, very heavy timbers (the outside chars and insulates the inside of the timber), and some specially made composite materials used for ﬁre doors.

13.12.5

Insulating materials

Building materials used for thermal or sound insulation could contribute to the spread of ﬁre. Only approved ﬁre resisting materials should be used.

13.12.6

Fire compartmentation

A compartment is a part of a building that is separated from all other parts by walls and ﬂoors, and is designed to contain a ﬁre for a speciﬁed time. The principal object is to limit the effect of both direct ﬁre damage and consequential business interruption caused by not only ﬁre spread but also smoke and water damage in the same ﬂoor and other storeys. Buildings are classiﬁed in purpose groups, according to their size. To control the spread of ﬁre, any building whose size exceeds that speciﬁed for its purpose group must be divided into compartments that do not exceed the prescribed limits of volume and ﬂoor area. Otherwise, they must be provided with special ﬁre protection. In the UK, the normal limit for the size of a compartment is 7000 m3. Compartments must be separated by walls and ﬂoors of sufﬁcient ﬁre resistance. Any openings needed in these walls or ﬂoors must be protected by ﬁre-resisting doors to ensure proper ﬁretight separation. Ventilation and heating ducts must be ﬁtted with ﬁre dampers where they pass through compartment walls and ﬂoors. Firebreak walls must extend completely across a building from outside wall to outside wall. They must be stable; they must be able to stand even when the part of the building on one side or the other is destroyed. No portion of the wall should be supported on unprotected steelwork nor should it have the ends of unprotected steel members embedded in it. The wall must extend up to the underside of a non-combustible roof surface, and sometimes above it. Any openings

Fire hazards and control must be protected to the required minimum grade of ﬁre resistance. If an external wall joins a ﬁrebreak wall and has an opening near the join, the ﬁrebreak wall may need to extend beyond the external wall. An important function of external walls is to contain a ﬁre within a building, or to prevent ﬁre spreading from outside. The ﬁre resistance of external walls should be related to the: ➤ purpose for which the building is used ➤ height, ﬂoor area and volume of the building ➤ distance of the building from relevant boundaries and other buildings ➤ extent of doors, windows and other openings in the wall. A wall, which separates properties from each other, should have no doors or other openings in it.

Blue

Provision of fire-fighting equipment

If ﬁre breaks out in the workplace and trained staff can safely extinguish it using suitable ﬁre-ﬁghting equipment, the risk to others will be removed. Therefore, all workplaces where people are at risk from ﬁre should be provided with suitable ﬁre-ﬁghting equipment. The most useful form of ﬁre-ﬁghting equipment for general ﬁre risks is the water-type extinguisher or suitable alternative. One such extinguisher should be provided for around each 200 m2 of ﬂoor space with a minimum of one per ﬂoor. If each ﬂoor has a hose reel, which is known to be in working order and of sufﬁcient length for the ﬂoor it serves, there may be no need for water-type extinguishers to be provided. Areas of special risks involving the use of oil, fats or electrical equipment may need carbon dioxide, dry powder or other types of extinguisher.

For liquid and electrical fires. DO NOT USE on metal fires

Cream

AFFF (Aqueous Film Forming Foam)

A multipurpose extinguisher to be used on Class B fires.

Cream

Foam

For use on liquid fires. DO NOT USE on electrical or metal fires

Red

Water

For wood, paper, textile and solid material fires. DO NOT USE on liquid, electrical or metal fires

Black

Carbon dioxide CO2

Canary Yellow

Figure 13.11

Standard dry powder or multi-purpose dry powder

13.13

Wet Chemical

For liquid and electrical fires. DO NOT USE metal

Cooking oils [Specially designed for high temperature cooking oils used in large industrial catering kitchens, restaurants and takeaway establishments etc.]

Types of fire extinguishers and labels.

219

Introduction to Health and Safety at Work Fire extinguishers should be sited on exit routes, preferably near to exit doors or where they are provided for speciﬁc risks, near to the hazards they protect. Notices indicating the location of ﬁre-ﬁghting equipment should be displayed where the location of the equipment is not obvious or in areas of high ﬁre risk where the notice will assist in reducing the risk to people in the workplace. All Halon ﬁre extinguishers, other than in deﬁned critical uses such as aircraft, military vehicles and vessels, have been decommissioned as of 31 December 2003 and disposed of safely.

13.14

Maintenance and testing of fire-fighting equipment

It is important that equipment is ﬁt for its purpose and is properly maintained and tested. One way in which this can be achieved, is through companies that specialize in the test and maintenance of ﬁre-ﬁghting equipment. All equipment provided to assist escape from the premises, such as ﬁre detection and warning systems and emergency lighting, and all equipment provided to assist with ﬁghting ﬁre, should be regularly checked and maintained by a suitably competent person in accordance with the manufacturer’s recommendations. Table 13.2 gives guidance on the frequency of test and maintenance and provides a simple guide to good practice. Table 13.2

13.15

Planning for an emergency and training staff

Each workplace should have an emergency plan. The plan should include the action to be taken by staff in the event of ﬁre, the evacuation procedure and the arrangements for calling the ﬁre brigade. For small workplaces this could take the form of a simple ﬁre action notice posted in positions where staff can read it and become familiar with it. High-ﬁre-risk or larger workplaces will need more detailed plans, which take account of the ﬁndings of the risk assessment, for example, the staff signiﬁcantly at risk and their location. For large workplaces, notices giving clear and concise instructions of the routine to be followed in case of ﬁre should be prominently displayed. The notice should include the method of raising an alarm in the case of ﬁre and the location of an assembly point to which staff escaping from the workplace should report. This information is given in Chapter 6.

13.16

Fire procedures and people with a disability

People with a disability (including members of the public) need special consideration, when planning for

Maintenance and testing of fire equipment

Equipment

Period

Action

Fire-detection and firewarning systems including self-contained smoke alarms and manually operated devices

Weekly

• Check all systems for state of repair and operation • Repair or replace defective units • Test operation of systems, self-contained alarms and manually operated devices

Annually

• Full check and test of system by competent service engineer • Clean self-contained smoke alarms and change batteries

Weekly

• Operate torches and replace batteries as required • Repair or replace any defective unit

Monthly

• Check all systems, units and torches for state of repair and apparent function

Annually

• Full check and test of systems and units by competent service engineer • Replace batteries in torches

Weekly

• Check all extinguishers including hose-reels for correct installation and apparent function

Annually

• Full check and test by competent service engineer

Emergency lighting including self-contained units and torches

Fire-fighting equipment including hose-reels

220

Fire hazards and control emergencies. But the problems this raises are seldom great. Employers should:

➤ identify everyone who may need special help to get out ➤ allocate responsibility to speciﬁc staff to help people with a disability in emergency situations ➤ consider possible escape routes ➤ enable the safe use of lifts ➤ enable people with a disability to summon help in emergencies ➤ train staff to be able to help their colleagues.

Advice on the needs of people with a disability, including sensory impairment, is available from the organizations which represent various groups. (Names and addresses can be found in the telephone directory.) People with impaired vision must be encouraged to familiarize themselves with escape routes, particularly those not in regular use. A ‘buddy’ system would be helpful. But, to take account of absences, more than one employee working near anyone with impaired vision should be taught how to help them. Staff with impaired hearing may not hear alarms in the same way as those with normal hearing but may still be able to recognize the sound. This may be tested during the weekly alarm audibility test. There are alternative means of signalling, such as lights or other visual signs, vibrating devices or specially selected sound signals. The Royal National Institute for Deaf People (19– 23 Featherstone St, London EC1) can advise. Ask the ﬁre brigade before installing alternative signals. Wheelchair users or others with impaired mobility may need help to negotiate stairs, etc. Anyone selected to provide this help should be trained in the correct methods. Advice on the lifting and carrying of people can be obtained from the Fire Service, Ambulance Service, British Red Cross Society, St John Ambulance Brigade or certain disability organizations. Lifts should not be used as a means of escape in the event of a ﬁre. If the power fails, the lift could stop between ﬂoors, trapping occupants in what may become a chimney of ﬁre and smoke. But BS 5588: Part 8 provides advice on specially designed lifts for use by the disabled in the event of a ﬁre. Employees with learning difﬁculties may also require special provision. Management should ensure that the colleagues of any employee with a learning difﬁculty know how to reassure them and lead them to safety.

13.17

Practice NEBOSH questions for Chapter 13

1. Explain the differences between the three types of enforcement notice which may be issued under the Regulatory Reform (Fire Safety) Order. 2. (a) With reference to the ﬁre triangle. outline TWO methods of extinguishing ﬁres. (b) State the ways in which persons could be harmed by a ﬁre in work premises. 3. (a) Explain using a suitable sketch, the signiﬁcance of the ‘ﬁre triangle’ (b) Identify FOUR different types of ignition source that may cause a ﬁre to occur, and give a typical workplace example of EACH type (c) For each type of ignition source identiﬁed in (b), outline the precautions that could be taken to prevent a ﬁre starting. 4. Identify the FOUR methods of heat transfer and explain how each can cause the spread of ﬁre. 5. (a) With reference to methods of heat transfer, explain how ﬁre in a workplace may spread. (b) Outline measures that should be taken to minimize the risk of ﬁre from electrical equipment. (c) Explain why water should not be used on ﬁres involving electrical equipment and identify TWO suitable extinguishing agents that could be used in such circumstances. 6. List EIGHT ways of reducing the risk of a ﬁre starting in a workplace. 7. Identify the FIVE stages of a ﬁre risk assessment in a low risk workplace. 8. In relation to a workplace ﬁre risk assessment, outline the issues that should be taken into account when assessing the means of escape. 9. Outline the precautions necessary for the safe storage and handling of small containers containing ﬂammable solvents. 10. Outline the main requirements for a safe means of escape from a building in the event of a ﬁre.

221

Introduction to Health and Safety at Work 11. List EIGHT features of a safe means of escape from a building in the event of ﬁre. 12. Give reasons that may delay the safe evacuation of employees from a workplace during a ﬁre. 13. (a) Outline the main factors to be considered in the siting of ﬁre extinguishers (b) Outline suitable arrangements for the inspection and maintenance of ﬁre extinguishers in the workplace. 14. (a) Identify TWO ways in which an alarm can be raised in the event of a ﬁre in a workplace (b) Outline the issues to consider the selection and siting of portable ﬁre extinguishers. 15. (a) Outline TWO advantages and TWO disadvantages of using hose reels as a means of extinguishing ﬁres (b) Outline the main factors to consider in the siting of hose reels.

222

16. With respect to the design features of a building: (i) identify TWO types of emergency warning systems that can be installed in the building to ensure that all employees can be made aware of the need to evacuate the building (ii) outline SIX structural measures that can help to prevent the spread of ﬁre and smoke. 17. Outline: (i) the various ways in which persons might be harmed by a ﬁre in work premises (ii) the additional measures that may be required to ensure the safe evacuation of employees with a range of physical impairments in the event of ﬁre. 18. Outline reasons and beneﬁts for undertaking regular ﬁre drills in the workplace. 19. Outline the issues that should be included in a training programme for employees on the emergency action to take in the event of ﬁre.

Chemical and biological health hazards and control

14.1 Introduction Occupational health is as important as occupational safety but generally receives less attention from managers. Every year twice as many people suffer ill-health caused or exacerbated by the workplace than suffer workplace injury. Although these illnesses do not usually kill people, they can lead to many years of discomfort and pain. Such illnesses include respiratory disease, hearing problems, asthmatic conditions and back pain. Furthermore, it has been estimated in the UK that 30% of all cancers probably have an occupational link – that linkage is known for certain in 8% of cancer cases. Work in the ﬁeld of occupational health has been taking place for the last four centuries and possibly longer. The main reason for the relatively low proﬁle for occupational health over the years has been the difﬁculty in linking the ill-health effect with the workplace cause. Many illnesses, such as asthma or back pain, can have a workplace cause but can also have other causes. Many of the advances in occupational health have been as a result of statistical and epidemiological studies (one wellknown such study linked the incidence of lung cancer to cigarette smoking). While such studies are invaluable in the assessment of health risk, there is always an element of doubt when trying to link cause and effect. The measurement of gas and dust concentrations is also subject to doubt when a correlation is made between a measured sample and the workplace environment from which it was taken. Occupational health, unlike occupational safety, is generally more concerned with probabilities than certainties. In this chapter, chemical and biological health hazards will be considered – other forms of health hazard will be covered in Chapter 15.

14

The chemical and biological health hazards described in this chapter are covered by the following health and safety regulations: ➤ Control of Substances Hazardous to Regulations ➤ Control of Lead at Work Regulations ➤ Control of Asbestos at Work Regulations.

Health

14.2 Forms of chemical agent Chemicals can be transported by a variety of agents and in a variety of forms. They are normally deﬁned in the following ways. Dusts are solid particles slightly heavier than air but often suspended in it for a period of time. The size of the particles ranges from about 0.4 μm (ﬁne) to 10 μm (coarse). Dusts are created either by mechanical processes (e.g. grinding or pulverizing) or construction processes (e.g. concrete laying, demolition or sanding), or by speciﬁc tasks (e.g. furnace ash removal). The ﬁne dust is much more hazardous because it penetrates deep into the lungs and remains there – known as respirable dust. In rare cases, respirable dust enters the bloodstream directly causing damage to other organs. Examples of such ﬁne dust are cement, granulated plastic materials and silica dust produced from stone or concrete dust. Repeated exposure may lead to permanent lung disease. Any dusts, which are capable of entering the nose and mouth during breathing, are known as inhalable dusts. Gases are any substances at a temperature above their boiling point. Steam is the gaseous form of water. Common gases include carbon monoxide, carbon dioxide,

223

Introduction to Health and Safety at Work nitrogen and oxygen. Gases are absorbed into the bloodstream where they may be beneﬁcial (oxygen) or harmful (carbon monoxide). Vapours are substances which are at or very close to their boiling temperatures. They are gaseous in form. Many solvents, such as cleaning ﬂuids, fall into this category. The vapours, if inhaled, enter the bloodstream and some can cause short-term effects (dizziness) and long-term effects (brain damage). Liquids are substances which normally exist at a temperature between freezing (solid) and boiling (vapours and gases). They are sometimes referred to as ﬂuids in health and safety regulations. Mists are similar to vapours in that they exist at or near their boiling temperature but are closer to the liquid phase. This means that there are suspended very small liquid droplets present in the vapour. A mist is produced during a spraying process (such as paint spraying). Many industrially produced mists can be very damaging if inhaled producing similar effects to vapours. It is possible for some mists to enter the body through the skin or by ingestion with food. Fume is a collection of very small metallic particles (less than 1 μm) which have condensed from the gaseous state. They are most commonly generated by the welding process. The particles tend to be within the respirable range (approximately 0.4–1.0 μm) and can lead to long-term permanent lung damage. The exact nature of any harm depends on the metals used in the welding process and the duration of the exposure.

14.3 Forms of biological agent As with chemicals, biological hazards may be transported by any of the following forms of agent. Fungi are very small organisms, sometimes consisting of a single cell, and can appear as plants (e.g. mushrooms and yeast). Unlike other plants, they cannot produce their own food but either live on dead organic matter or on living animals or plants as parasites. Fungi reproduce by producing spores which can cause allergic reactions when inhaled. The infections produced in man by fungi may be mild, such as athlete’s foot, or severe such as ringworm. Many fungal infections can be treated with antibiotics. Moulds are a particular group of very small fungi which, under damp conditions, will grow on surfaces such as walls, bread, cheese, leather and canvas. They can be beneﬁcial (penicillin) or cause allergic reactions (asthma). Asthma attacks, athlete’s foot and farmer’s lung are all examples of fungal infections. Bacteria are very small single-celled organisms which are much smaller than cells within the human body.

224

They can live outside the body and be controlled and destroyed by antibiotic drugs. There is evidence that bacteria are becoming resistant to most antibiotics. This has been caused by the widespread misuse of antibiotics. It is important to note that not all bacteria are harmful to humans. Bacteria aid the digestion of food and babies would not survive without their aid to break down the milk in their digestive systems. Legionella, tuberculosis and tetanus are all bacterial diseases. Viruses are minute non-cellular organisms which can only reproduce within a host cell. They are very much smaller than bacteria and cannot be controlled by antibiotics. They appear in various shapes and are continually developing new strains. They are usually only defeated by the defence and healing mechanisms of the body. Drugs can be used to relieve the symptoms of a viral attack but cannot cure it. The common cold is a viral infection as are hepatitis, AIDS (HIV) and inﬂuenza.

14.4 Classification of hazardous substances and their associated health risks A hazardous substance is one which can cause ill-health to people at work. Such substances may include those used directly in the work processes (glues and paints), those produced by work activities (welding fumes) or those which occur naturally (dust). Hazardous substances are classiﬁed according to the severity and type of hazard which they may present to people who may come into contact with them. The contact may occur while working or transporting the substances or might occur during a ﬁre or accidental spillage. There are several classiﬁcations but here only the ﬁve most common will be described. Irritant is a non-corrosive substance which can cause skin (dermatitic) or lung (bronchial) inﬂammation after repeated contact. People who react in this way to a particular substance are sensitized or allergic to that substance. In most cases, it is likely that the concentration of the irritant may be more signiﬁcant than the exposure time. Many household substances, such as wood preservatives, bleaches and glues are irritants. Many chemicals used as solvents are also irritants (white spirit, toluene and acetone). Formaldehyde and ozone are other examples of irritants. Corrosive substances are ones which will attack, normally by burning, living tissue. Usually a strong acid or alkali, examples include sulphuric acid and caustic soda. Many tough cleaning substances, such as kitchen oven cleaners, are corrosives as are many dishwasher crystals. Harmful is the most commonly used classiﬁcation and describes a substance which, if swallowed, inhaled or penetrates the skin, may pose limited health risks. These

Chemical and biological health hazards and control

Harmful (Xn)

Figure 14.1

Irritant (Xi)

Corrosive (C)

Toxic (T)

Carcinogenic (T)

Classification symbols.

risks can usually be minimized or removed by following the instruction provided with the substance (e.g. by using personal protective equipment). There are many household substances which fall into this category including bitumen-based paints and paint brush restorers. Many chemical cleansers, such as trichloroethylene, are categorized as harmful. It is very common for substances labelled harmful also to be categorized as irritant. Toxic substances are ones which impede or prevent the function of one or more organs within the body, such as the kidney, liver and heart. A toxic substance is, therefore, a poisonous one. Lead, mercury, pesticides and the gas carbon monoxide are toxic substances. The effect on the health of a person exposed to a toxic substance depends on the concentration and toxicity of the substance, the frequency of the exposure and the effectiveness of the control measures in place. The state of health and age of the person and the route of entry into the body have inﬂuence on the effect of the toxic substance. Carcinogenic substances are ones which are known or suspected of promoting abnormal development of body cells to become cancers. Asbestos, hard wood dust, creosote and some mineral oils are carcinogenic. It is very important that the health and safety rules accompanying the substance are strictly followed. Mutagenic substances are those which damage genetic material within cells causing abnormal changes that can be passed from one generation to another. Each of the classiﬁcations may be identiﬁed by a symbol and a symbolic letter – the most common of these are shown in Figure 14.1. The effects on health of hazardous substances may be either acute or chronic. Acute effects are of short duration and appear fairly rapidly, usually during or after a single or short-term exposure to a hazardous substance. Such effects may be severe and require hospital treatment but are usually reversible. Examples include asthma-type attacks, nausea and fainting. Chronic effects develop over a period of time which may extend to many years. The word ‘chronic’ means ‘with time’ and should not be confused with ‘severe’ as its use in everyday speech often implies. Chronic health effects are produced from prolonged or repeated exposures to

hazardous substances resulting in a gradual, latent and often irreversible illness, which may remain undiagnosed for many years. Many cancers and mental diseases fall into the chronic category. During the development stage of a chronic disease, the individual may experience no symptoms.

14.4.1 The role of COSHH The Control of Substances Hazardous to Health Regulations 1988 (COSHH) were the most comprehensive and signiﬁcant piece of Health and Safety legislation to be introduced since the Health and Safety at Work Act 1974. They were enlarged to cover biological agents in 1994 and further amended in 1997, 1999, 2002, and 2005. A detailed summary of these Regulations appears in Chapter 17. The Regulations impose duties on employers to protect employees and others who may be exposed to substances hazardous to their health and requires employers to control exposure to such substances. The COSHH Regulations offer a framework for employers to build a management system to assess health risks and to implement and monitor effective controls. Adherence to these Regulations will provide the following beneﬁts to the employer and employee: ➤ Improved productivity due to lower levels of illhealth and more effective use of materials ➤ Improved employee morale ➤ lower numbers of civil court claims ➤ better understanding of health and safety legal requirements. Organizations which ignore COSHH requirements, will be liable for enforcement action, including prosecution, under the Regulations.

14.5 Routes of entry to the human body There are three principal routes of entry of hazardous substances into the human body: ➤ inhalation – breathing in the substance with normal air intake. This is the main route of contaminants

225

Introduction to Health and Safety at Work into the body. These contaminants may be chemical (e.g. solvents or welding fume) or biological (e.g. bacteria or fungi) and become airborne by a variety of modes, such as sweeping, spraying, grinding and bagging. They enter the lungs where they have access to the bloodstream and many other organs ➤ absorption through the skin – the substance comes into contact with the skin and enters either through the pores or a wound. Tetanus can enter in this way as can toluene, benzene and various phenols ➤ ingestion – through the mouth and swallowed into the stomach and the digestive system. This is not a signiﬁcant route of entry to the body. The most common occurrences are due to airborne dust or poor personal hygiene (not washing hands before eating food). Another very rare entry route is by injection. The abuse of compressed air lines by shooting high pressure air at the skin can lead to air bubbles entering the bloodstream. Accidents involving hypodermic syringes in a health or veterinary service setting are rare but illustrate this form of entry route. The most effective control measures which can reduce the risk of infection from biological organisms are disinfection, proper disposal of clinical waste Routes of entry to the human body (including syringes), good personal hygiene and, where appropriate, personal protective equipment. Other measures include vermin control, water treatment and immunization. There are ﬁve major functional systems within the human body – respiratory, nervous, cardiovascular (blood), urinary and the skin.

14.5.1 The respiratory system This comprises the lungs and associated organs (e.g. the nose). Air is breathed in through the nose, passes through the trachea (windpipe) and the bronchi into the two lungs. Within the lungs, the air enters many smaller passageways (bronchioli) and thence to one of 300 000 terminal sacs called alveoli. The alveoli are approximately 0.1 mm across, although the entrance is much smaller. On arrival in the alveoli, there is a diffusion of oxygen into the bloodstream through blood capillaries and an effusion of carbon dioxide from the bloodstream. While soluble dust which enters the alveoli will be absorbed into the bloodstream, insoluble dust (respirable dust) will remain permanently, leading to possible chronic illness. The whole of the bronchial system is lined with hairs, known as cilia. The cilia offer some protection against insoluble dusts. These hairs will arrest all non-respirable dust (above 5 μm) and, with the aid of mucus, pass the dust from one hair to a higher one and thus bring the dust back to the throat. (This is known as the ciliary escalator). It has been shown that smoking damages this action. The nose will normally trap large particles (greater than 20 mm) before they enter the trachea. Respirable dust tends to be long thin particles with sharp edges which puncture the alveoli walls. The puncture heals producing scar tissues which are less ﬂexible than the original walls – this can lead to ﬁbrosis. Such dusts include asbestos, coal, silica, some plastics and talc. Acute effects on the respiratory system include bronchitis and asthma and chronic effects include ﬁbrosis

Nose Pharynx Epiglottis Larynx

Trachea Apex

Apex Left primary br onchus

Right lung

Ribs Bronchiole Heart space

Figure 14.2

226

Alveoli (air sacs)

Diaphragm Base of left lung

Inferior vena cava

Aorta

The upper and lower respiratory system.

Vertebral column

Chemical and biological health hazards and control Brain

Trachea Primary bronchus

Spinal cord

Lobar bronchus

Passages of air conduction

Segmental bronchus

Peripheral nerves

Bronchioles

Central nervous system Respiratory bronchioles

Lobule

Peripheral nervous system Passages where gases exchange

Figure 14.3

The nervous system.

Alveolar duct Alveolus

Figure 14.2

Continued. Heart

and cancer. Hardwood dust, for example, can produce asthma attacks and nasal cancer. Finally, asphyxiation, due to a lack of oxygen, is a problem in conﬁned spaces particularly when MIG (metal inert gas) welding is taking place.

Blood vessels

14.5.2 The nervous system The nervous system consists primarily of the brain, the spinal cord and nerves extending throughout the body. Any muscle movement or sensation (e.g. hot and cold) is controlled or sensed by the brain through small electrical impulses transmitted through the spinal cord and nervous system. The effectiveness of the nervous system can be reduced by neurotoxins and lead to changes in mental ability (loss of memory and anxiety), epilepsy and narcosis (dizziness and loss of consciousness). Organic solvents (trichloroethylene) and heavy metals (mercury) are well-known neurotoxins. The expression ‘mad hatters’ originated from the mental deterioration of top hat polishers in the 19th century who used mercury to produce a shiny ﬁnish on the top hats.

Figure 14.4

The cardiovascular system.

within which are red cells, white cells and platelets. The system has three basic objectives:

14.5.3 The cardiovascular system

➤ to transport oxygen to vital organs, tissues and the brain and carbon dioxide back to the lungs (red cell function); ➤ to attack foreign organisms and build up a defence system (white cell function); ➤ to aid the healing of damaged tissue and prevent excessive bleeding by clotting (platelets).

The blood system uses the heart to pump blood around the body through arteries, veins and capillaries. Blood is produced in the bone marrow and consists of a plasma

There are several ways in which hazardous substances can interfere with the cardiovascular system. Benzene can affect the bone marrow by reducing the number

227

Introduction to Health and Safety at Work of blood cells produced. Carbon monoxide prevents the red cells from absorbing sufﬁcient oxygen and the effects depend on its concentration. Symptoms begin with headaches and end with unconsciousness and possibly death.

14.5.4 The urinary system The urinary system extracts waste and other products from the blood. The two most important organs are the liver (normally considered part of digestive system) and the kidneys, both of which can be affected by hazardous substances within the bloodstream. The liver removes toxins from the blood, maintains the levels of blood sugars and produces protein for the blood plasma. Hazardous substances can cause the liver to be too active or inactive (e.g. xylene), lead to liver enlargement (e.g. cirrhosis caused by alcohol) or liver cancer (e.g. vinyl chloride). The kidneys ﬁlter waste products from the blood as urine, regulate blood pressure and liquid volume in the body and produce hormones for making red blood cells. Heavy metals (e.g. cadmium and lead) and organic solvents (e.g. glycol ethers used in screen printing) can restrict the operation of the kidneys possibly leading to failure.

Inferior vena cava

Left kidney Pancreas

Duodenum Aorta Left ureter

Right ureter

Bladder

228

The skin holds the body together and is the ﬁrst line of defence against infection. It regulates body temperature, is a sensing mechanism, provides an emergency food store (in the form of fat) and helps to conserve water. There are two layers – an outer layer called the epidermis (0.2 mm) and an inner layer called the dermis (4 mm). The epidermis is a tough protective layer and the dermis contains the sweat glands, nerve endings and hairs. The most common industrial disease of the skin is dermatitis (non-infective dermatitis). It begins with a mild irritation on the skin and develops into blisters which can peel and weep becoming septic. It can be caused by various chemicals, mineral oils and solvents. There are two types: ➤ irritant contact dermatitis occurs soon after contact with the substance and the condition reverses after contact ceases (detergents and weak acids) ➤ allergic contact dermatitis is caused by a sensitizer such as turpentine, epoxy resin, solder ﬂux and formaldehyde. For many years, dermatitis was seen as a ‘nervous’ disease which was psychological in nature. Nowadays, it is recognized as an industrial disease which can be controlled by good personal hygiene, personal protective equipment, use of barrier creams and health screening of employees. Dermatitis can appear anywhere on the body but it is normally found on the hands. Therefore, gloves should always be worn when there is a risk of dermatitis. The risks of dermatitis occurring increases with the presence of skin cuts or abrasions, which allow chemicals to be more easily absorbed, and the type, sensitivity and existing condition of the skin.

14.6 Health hazards of specific agents

Right kidney

Figure 14.5

14.5.5 The skin

Parts of the urinary system.

The health hazards associated with hazardous substances can vary from very mild (momentary dizziness or a skin irritation) to very serious, such as a cancer. Cancer is a serious body cell disorder in which the cells develop into tumours. There are two types of tumour – benign and malignant. Benign tumours do not spread but remain localized within the body and grow slowly. Malignant tumours are called cancers and often grow rapidly, spreading to other organs using the bloodstream and lymphatic glands. Survival rates have improved dramatically in recent years as detection methods have improved and the tumours are found in their early stages of development. A minority of cancers are believed to be occupational in origin.

Chemical and biological health hazards and control

Hair shaft Stratum corneum

Opening of sweat ducts

Epidermis

Germinative layer

Dermal papilla

Dermis

Meissner’s corpuscle Sebaceous gland

Subcutaneous tissue

Arrector pili muscle Hair follicle Hair root Cutaneous nerve

Figure 14.6

Pacinian corpuscle Sweat gland

The skin – main structures in the dermis.

Occupational asthma has approximately 4 m suffers in the UK and it is estimated that 13 m working days are lost each year as a result of it. It is mainly caused by breathing in respiratory sensitizers, such as wood dusts, organic solvents, solder ﬂux fumes or animal hair. The symptoms are coughing, wheezing, tightness of the chest and breathlessness due to a constriction of the airways. It can be a mild attack or a serious one that requires hospitalization. There is some evidence that stress can trigger an attack. The following common agents of health hazards will be described together with the circumstances in which they may be found: Ammonia is a colourless gas with a distinctive odour which, even in small concentrations, causes the eyes to smart and run and a tightening of the chest. It is a corrosive substance which can burn the skin, burn and seriously damage the eye, cause soreness and ulceration of the throat and severe bronchitis and oedema (excess of ﬂuid) of the lungs. Good eye and respiratory protective equipment is essential when maintaining equipment containing ammonia. Any such equipment should be tested regularly for leaks and repaired promptly if required. Ammonia is also used in the production of fertilizers and synthetic ﬁbres. Most work on ammonia plant should require a permit-to-work procedure. Chlorine is a greenish, toxic gas with a pungent smell which is highly irritant to the respiratory system, producing severe bronchitis and oedema of the lungs and may also cause abdominal pain, nausea and vomiting. It is

used as a disinfectant for drinking water and swimming pool water and in the manufacture of chemicals. Organic solvents are used widely in industry as cleansing and degreasing agents. There are two main groups – the hydrocarbons (includes the aromatic and aliphatic hydrocarbons) and the non-hydrocarbons (such as toluene, white spirit, trichloroethylene and carbon tetrachloride). All organic solvents are heavier than air and most are sensitizers and irritants. Some are narcotics, while others can cause dermatitis and after long exposure periods liver and kidney failure. It is very important that the hazard data sheet accompanying the particular solvent is read and the recommended personal protective equipment is worn at all times. Solvents are used extensively in a wide variety of industries as varnishes, paints, adhesives, glue strippers, printing inks and thinners. They are at highest risk when used as sprays. One of the most hazardous is dichloromethane (DCM) also known as methylene chloride. It is used as a paint stripper normally as a gel. It can produce narcotic effects and has been classiﬁed as a category 3 carcinogen in the European Community. The minimum personal protective equipment requirements are impermeable overalls, apron, footwear, long gloves and gauntlet and chemically resistant goggles or visor. Respiratory protection equipment is also required if it cannot be demonstrated that exposure is below the workplace exposure limit (WEL). Carbon dioxide is a colourless and odourless gas which is heavier than air. It represses the respiratory system,

229

Introduction to Health and Safety at Work eventually causing death by asphyxiation. At low concentrations it will cause headaches and sweating followed by a loss of consciousness. The greatest hazard occurs in conﬁned spaces, particularly where the gas is produced as a by-product. Carbon monoxide is a colourless, tasteless and odourless gas which makes it impossible to detect without special measuring equipment. As explained earlier, carbon monoxide enters the blood (red cells) more readily than oxygen and restricts the supply of oxygen to vital organs. At low concentrations in the blood (less than 5%), headaches and breathlessness will occur, while at higher concentrations unconsciousness and death will result. The most common occurrence of carbon monoxide is as an exhaust gas either from a vehicle or a heating system. In either case, it results from inefﬁcient combustion and, possibly, poor maintenance. Isocyanates are volatile organic compounds widely used in industry for products such as printing inks, adhesives, two-pack paints (particularly in vehicle body shops) and in the manufacture of plastics (polyurethane products). They are irritants and sensitizers. Inﬂammation of the nasal passages, the throat and bronchitis are typical reactions to many isocyanates. When a person becomes sensitized to an isocyanate, very small amounts of the substance often provoke a serious reaction similar to an extreme asthma attack. Isocyanates also present a health hazard to ﬁre ﬁghters. They are subject to a workplace exposure limit (WEL) and respiratory protective equipment should normally be worn. Asbestos appears in three main forms – crocidolite (blue), amosite (brown) and chrysotile (white). The blue and brown asbestos are considered to be the most dangerous and may be found in older buildings where they were used as heat insulators around boilers and hot water pipes and as ﬁre protection of structure. White asbestos has been used in asbestos cement products and brake linings. It is difﬁcult to identify an asbestos product by its colour alone – laboratory identiﬁcation is usually required. Asbestos produces a ﬁne ﬁbrous dust of respirable dust size which can become lodged in the lungs. The ﬁbres can be very sharp and hard causing damage to the lining of the lungs over a period of many years. This can lead to one of the following diseases: ➤ asbestosis or ﬁbrosis (scarring) of the lungs ➤ lung cancer ➤ mesothelioma – cancer of the lining of the lung or, in rarer cases, the abdominal cavity. If asbestos is discovered during the performance of a contract, work should cease immediately and the employer be informed. Typical sites of asbestos include ceiling tiles, asbestos cement roof and wall sheets, sprayed asbestos coatings on structural members, loft

230

insulation and asbestos gaskets. Asbestos has its own set of Regulations (Control of Asbestos Regulations) and a summary of these is given in Chapter 17. These cover the need for a risk assessment, a method statement covering the removal and disposal, air monitoring procedures and the control measures (including personal protective equipment and training) to be used. The most recent set of asbestos regulations has removed textured coatings (decorative products, such as Artex, Wondertex and Pebblecoat) from the asbestos licensing regime. Until 1992, these products contained white asbestos. This amendment by the HSE followed research work by the Health and Safety Laboratory. The new regulations introduce an additional training requirement for asbestos awareness training. Such training should include: ➤ the health risks caused by exposure to asbestos ➤ the materials that are likely to contain asbestos and where they are likely to be found ➤ the methods to reduce asbestos risks during work, and ➤ the action to take in an emergency, such as an uncontrolled release of asbestos dust. Asbestos is responsible for at least 4000 deaths in the UK each year and the HSE felt that there was a need to increase awareness amongst the workforce of the risks associated with this material. Lead is a heavy, soft and easily worked metal. It is used in many industries but is most commonly associated with plumbing and rooﬁng work. Lead enters the body normally by inhalation but can also enter by ingestion and skin contact. The main targets for lead are the spinal cord and the brain, the blood and blood production. The effects are normally chronic and develop as the quantity of lead builds up. Headaches and nausea are the early symptoms followed by anaemia, muscle weakening and (eventually) coma. Regular blood tests are a legal and sensible requirement as are good ventilation and the use of appropriate personal protective equipment. High personal hygiene standards and adequate welfare (washing) facilities are essential and must be used before smoking or food is consumed. The reduction in the use of leaded petrol was an acknowledgement of the health hazard represented by lead in the air. Lead is covered by its own set of regulations – the Control of Lead at Work Regulations (summarized in Chapter 17). These regulations require risk assessments to be undertaken and engineering controls to be in place. They also recognize that lead can be transferred to an unborn child through the placenta and, therefore, offer additional protection to women of reproductive capacity. Medical surveillance, in the form of a blood test, of all employees, who come into

Chemical and biological health hazards and control contact with lead operations, is required by the regulations. Such tests should take place at least once a year. Silica is the main component of most rocks and is a crystalline substance made of silicon and oxygen. It occurs in quartz (found in granite), sand and ﬂint. Harm is caused by the inhalation of silica dust which can lead to silicosis (acute and chronic), ﬁbrosis and pneumoconiosis. The dust which causes the most harm is respirable dust which becomes trapped in the alveoli. This type of dust is sharp and very hard and, probably, causes wounding and scarring of lung tissue. As silicosis develops, breathing becomes more and more difﬁcult and eventually as it reaches its advanced stage, lung and heart failure occur. It has also been noted that silicosis can result in the development of tuberculosis as a further complication. Hard rock miners, quarrymen, stone and pottery workers are most at risk. Health surveillance is recommended for workers in these occupations at initial employment and at subsequent regular intervals. Prevention is best achieved by the use of good dust extraction systems and respiratory personal protective equipment. Leptospirosis and Weil’s disease is caused by a bacterium found in the urine of rats. In humans, the kidneys and liver are attacked causing high temperatures and headaches followed by jaundice and, in up to 20% of cases, it can be fatal. It enters the body either through the skin or by ingestion. The most common source is contaminated water in a river, sewer or ditch and workers, such as canal or sewer workers, are most at risk. Leptospirosis is always a risk where rats are present, particularly if the associated environment is damp. Good impervious protective clothing, particularly wellington boots, is essential in these situations and the covering of any skin wounds. For workers who are frequently in high-risk environments (sewer workers), immunization with a vaccine may be the best protection. Weil’s disease is strictly a severe form of leptospirosis. The symptoms of leptospirosis are similar to inﬂuenza but those for Weil’s disease are anaemia, nose bleeds and jaundice. While the most common source of infection is from the urine of rats, it has been found in other animals, such as cattle; therefore, farm and veterinary workers may also be at risk. Legionella is an airborne bacterium and is found in a variety of water sources. It produces a form of pneumonia caused by the bacteria penetrating to the alveoli in the lungs. This disease is known as Legionnaires’ disease, named after the ﬁrst documented outbreak at a State Convention of the American Legion held at Pennsylvania in 1976. During this outbreak, 200 men were affected, of whom 29 died. That outbreak and many subsequent ones were attributed to air-conditioning systems. The legionella bacterium cannot survive at temperatures above 608ºC but grows between 20 and

458ºC, being most virulent at 378ºC. It also requires food in the form of algae and other bacteria. Control of the bacteria involves the avoidance of water temperatures between 20 and 458ºC, avoidance of water stagnation and the build-up of algae and sediments and the use of suitable water treatment chemicals. This work is often done by a specialist contractor. The most common systems at risk from the bacterium are: ➤ water systems incorporating a cooling tower ➤ water systems incorporating an evaporative condenser ➤ hot and cold water systems and other plant where the water temperature may exceed 208ºC. An approved code of practice (Legionnaires’ disease – The control of legionella bacteria in water systems – L8) was produced by the Health and Safety Executive in 2000. Where plant at risk of the development of legionella exists, the following is required: ➤ a written ‘suitable and sufﬁcient’ risk assessment ➤ the preparation and implementation of a written control scheme involving the treatment, cleaning and maintenance of the system ➤ appointment of a named person with responsibility for the management of the control scheme ➤ the monitoring of the system by a competent person ➤ record keeping and the review of procedures developed within the control scheme. The code of practice also covers the design and construction of hot and cold water systems and cleaning and disinfection guidance. There have been several cases of members of the public becoming infected from a contaminated cooling tower situated on the roof of a building. It is required that all cooling towers are registered with the local authority. People are more susceptible to the disease if they are older or weakened by some other illness. It is, therefore, important that residential and nursing homes and hospitals are particularly vigilant. Hepatitis is a disease of the liver and can cause high temperatures, nausea and jaundice. It can be caused by hazardous substances (some organic solvents) or by a virus. The virus can be transmitted from infected faeces (hepatitis A) or by infected blood (hepatitis B and C). The normal precautions include good personal hygiene particularly when handling food and in the use of blood products. Hospital workers who come into contact with blood products are at risk of hepatitis as are drug addicts who share needles. It is also important that

231

Introduction to Health and Safety at Work workers at risk regularly wash their hands and wear protective disposable gloves.

14.7 Requirements of the COSHH Regulations When hazardous substances are considered for use (or in use) at a place of work, the COSHH Regulations impose certain duties on employers and require employees to cooperate with the employer by following any measures taken to fulﬁl those duties. The principal requirements are as follows: 1.

2.

3. 4.

5.

6.

7.

employers must undertake a suitable and sufﬁcient assessment of the health risks ocreated by work which is liable to expose their employees to substances hazardous to health and of the steps that need to be taken by employers to meet the requirements of these Regulations (Regulation 6) employers must prevent, or where this is not reasonably practicable, adequately control the exposure of their employees to substances hazardous to health. Workplace exposure limits (WEL), which should not be exceeded, are speciﬁed by the Health and Safety Executive for certain substances. As far as inhalation is concerned, control should be achieved by means other than personal protective equipment. If, however, respiratory equipment, for example, is used, then the equipment must conform to HSE standards (Regulation 7) employers and employees must make proper use of any control measures provided (Regulation 8) employers must maintain any installed control measures on a regular basis and keep suitable records (Regulation 9) monitoring must be undertaken of any employee exposed to items listed in schedule 5 of the Regulations or in any other case where monitoring is required for the maintenance of adequate control or the protection of employees. Records of this monitoring must be kept for at least 5 years, or 40 years where employees can be identiﬁed (Regulation 10) health surveillance must be provided to any employees who are exposed to any substances listed in schedule 6. Records of such surveillance must be kept for at least 40 years after the last entry (Regulation 11) employees who may be exposed to substances hazardous to their health must be given information, instruction and training sufﬁcient for them to know the health risks created by the exposure and the precautions which should be taken (Regulation 12).

232

14.8 Details of a COSHH assessment Not all hazardous substances are covered by the COSHH Regulations. If there is no warning symbol on the substance container or it is a biological agent which is not directly used in the workplace (such as an inﬂuenza virus), then no COSHH assessment is required. The COSHH Regulations do not apply to those hazardous substances which are subject to their own individual regulations (asbestos, lead or radioactive substances). The COSHH Regulations do apply to the following substances: ➤ substances having occupational exposure limits as listed in the HSE publication EH40 (Occupational Exposure Limits) ➤ substances or combinations of substances listed in the Chemicals (Hazard, Information and Packaging for Supply) Regulations better known as the CHIP Regulations ➤ biological agents connected with the workplace ➤ substantial quantities of airborne dust (more the 10 mg/m3 of total inhalable dust or 4 mg/m3 of respirable dust, both 8 hour time-weighted average, when there is no indication of a lower value) ➤ any substance creating a comparable hazard which for technical reasons may not be covered by CHIP.

14.8.1 Assessment requirements A COSHH assessment is very similar to a risk assessment but is applied speciﬁcally to hazardous substances. There are six stages to a COSHH assessment: 1.

2. 3. 4. 5. 6.

identify the hazardous substances present in the workplace and those who could be affected by them gather information about the hazardous substances evaluate the risks to health decide on the control measures, if any, required, including information, instruction and training record the assessment review the assessment.

It is important that the assessment is conducted by somebody who is competent to undertake it. Such competence will require some training, the extent of which will depend on the complexities of the workplace. For large organizations with many high-risk operations, a team of competent assessors will be needed. If the assessment is simple and easily repeated, a written record is not necessary. In other cases, a concise and dated record of the assessment together with recommended control measures should be made available to all those likely to be affected by the hazardous substances. The assessment

Chemical and biological health hazards and control should be reviewed on a regular basis, particularly when there are changes in work process or substances or when adverse ill-health is reported.

14.8.2 Workplace exposure limits One of the main purposes of a COSHH assessment is to adequately control the exposure of employees and others to hazardous substances. This means that such substances should be reduced to levels which do not pose a health threat to those exposed to them day after day at work. Under the 2005 amendments to the COSHH Regulations 2002, the Health and Safety Commission has assigned workplace exposure limits (WELs) to a large number of hazardous substances and publishes an annual update in a publication called ‘Occupational Exposure limits’ EH40. The workplace exposure limit is related to the concentration of airborne hazardous substances that people breathe over a speciﬁed period of time – known as ‘time weighted average’. Before the introduction of WELs, there were two types of exposure limits published – the maximum exposure limit (MEL) and the occupational exposure standard (OES). The COSHH (Amendment) Regulations 2005 replaced the OES/MEL system with a single Workplace Exposure Limit (WEL). THis removed the concern of HSC that the OES was seen as a ‘safe’ limit rather than a ‘likely safe’ limit. Hence, the Workplace Exposure Limit (WEL) must not be exceeded. Hazardous substances which have been assigned a WEL fall into two groups: 1.

2.

Substance which are carcinogenic or mutagenic (having a risk phase R45, R46 or R49) or could cause occupational asthma (having a risk phase R42, or R42/43 or listed in section C of the HSE publication ‘Asthmagen? Critical assessment for the agents implicated in occupational asthma’ as updated from time to time) or are listed in Schedule 1 of the COSHH Regulations. These are substances which were assigned a maximum exposure limit (MEL) before 2005. The level of exposure to these substances should be reduced as far as is reasonably practicable. All other hazardous substances which have been assigned a WEL. Exposure to these substances by inhalation must be controlled adequately to ensure that the WEL is not exceeded. These substances were previously assigned an occupational exposure standard (OES) before 2005. For these substances, employers should achieve adequate control of exposure by inhalation by applying the principles of good practice outlined in the approved code of practice and listed in section 14.9.1. The implication of these principles is discussed later in this chapter.

The workplace exposure limits are subject to timeweighted averaging. There are two such time-weighted averages (TWA): the long-term exposure limit (LTEL) or 8 hour reference period, and the short-term exposure limit (STEL) or 15 minute reference period. The 8 hour TWA is the maximum exposure allowed over an 8 hour period so that if the exposure period was less than 8 hours the workplace exposure limit is increased accordingly with the proviso that exposure above the LTEL value continues for no longer than 1 hour. Table 14.1 shows some typical workplace exposure limits for various hazardous substances. For example, If a person was exposed to a hazardous substance with a WEL of 100 mg/m3 (8 hour TWA) for 4 hours, no action would be required until an exposure level of 200 mg/m3 was reached (further exposure at levels between 100 and 200 mg/m3 should be restricted to 1 hour). If, however, the substance has an STEL of 150 mg/m3, then action would be required when the exposure level rose above 150 mg/m3 for more than 15 minutes. The STEL always takes precedence over the LTEL. When a STEL is not given, it should be assumed that it is three times the LTEL value. The publication EH40 is a valuable document for the health and safety professional since it contains much additional advice on hazardous substances for use during the assessment of health risks, particularly where new medical information has been made public. The HSE are constantly revising WELs and introducing new ones and it is important to refer to the latest publication of EH40. It is important to stress that if a WEL from Group 1 is exceeded, the process and use of the substance should cease immediately and employees removed from the immediate area until it can be made safe. In the longer term the process and the control and monitoring measures should be reviewed and health surveillance of the affected employees considered.

Table 14.1 Examples of Workplace Exposure Limits (WELs)

Group 1 WELs

LTEL (8 hr TWA)

STEL (15 min)

All isocyanates

0.02 mg/m3

0.07 mg/m3

Styrene

430 mg/m3

1080 mg/m3

Ammonia

18 mg/m3

25 mg/m3

Toluene

191 mg/m3

574 mg/m3

Group 2 WELs

233

Introduction to Health and Safety at Work Adjustments must be made when exposure occurs over a continuous period longer than 8 hours ➤ they can only be used for exposure in a workplace and not to evaluate or control non-occupational exposure (e.g. to evaluate exposure levels in a neighbourhood close to the workplace, such as a playground) ➤ WELs are only approved where the atmospheric pressure varies from 900 to 1100 millibars. This could exclude their use in mining and tunnelling operations ➤ they should also not be used when there is a rapid build-up of a hazardous substance due to a serious accident or other emergency. Emergency arrange ments should cover these eventualities. The fact that a substance has not been allocated a WEL does not mean that it is safe. The exposure to these substances should be controlled to a level to which nearly all of the working population could be exposed all the time without any adverse effects to their health. Detailed guidance and references are given for such substances in the HSE ACOP and guidance to the COSHH Regulations (L5). HSC has publishing a revised ACOP and EH40 to include these changes. More information on the latest COSHH Regulations is given in Chapter 17.

14.8.3 Sources of information There are other important sources of information available for a COSHH assessment in addition to the HSE Guidance Note EH40.

Figure 14.7

Typical product labels and data sheets.

The over-riding requirement for any hazardous substance, which has a WEL from Group 1, is to reduce exposure to as low as is reasonably practicable. Finally, there are certain limitations on the use of the published workplace exposure limits: ➤ they are speciﬁcally quoted for an 8 hour period (with an additional STEL for many hazardous substances).

234

Product labels include details of the hazards associated with the substances contained in the product and any precautions recommended. They may also bear one or more of the CHIP hazard classiﬁcation symbols. Product safety data sheets are another very useful source of information for hazard identiﬁcation and associated advice. Manufacturers of hazardous substances are obliged to supply such sheets to users giving details of the name, chemical composition and properties of the substance. Information on the nature of the health hazards and any relevant exposure standard (WEL) should also be given together with recommended exposure control measures and personal protective equipment. The sheets contain useful additional information on ﬁrst aid and ﬁre-ﬁghting measures and handling, storage, transport and disposal information. The data sheets should be stored in a readily accessible and known place for use in the event of an emergency, such as an accidental release. Other sources of information include trade association publications, industrial codes of practice and specialist reference manuals.

Chemical and biological health hazards and control 14.8.4 Survey techniques for health risks An essential part of the COSHH assessment is the measurement of the quantity of the hazardous substance in the atmosphere surrounding the workplace. This is known as air sampling. There are four common types of air sampling techniques used for the measurement of air quality: 1.

Stain tube detectors use direct reading glass indicator tubes ﬁlled with chemical crystals which change colour when a particular hazardous substance passes through them. The method of operation is very similar to the breathalyser used by the police to check alcohol levels in motorists. The glass tube is opened at each end and ﬁtted into a pumping device (either hand or electrically operated). A speciﬁc quantity of contaminated air, containing the hazardous substance, is drawn through the tube and the crystals in the tube change colour in the direction of the air ﬂow. The tube is calibrated such that the extent of the colour change along the tube indicates the concentration of the hazardous substance within the air sample.

This method can only be effective if there are no leakages within the instrument and the correct volume of sampled air is used. The instrument should be held within 30 cm of the nose of the person whose atmosphere is being tested. A large range of different tubes is available. This technique of sampling is known as grab or spot sampling since it is taken at one point. The advantages of the technique are that it is quick, relatively simple to use and inexpensive. There are, however, several disadvantages: ➤ the instrument cannot be used to measure concentrations of dust or fume ➤ the accuracy of the reading is approximately 25% it will yield a false reading if other contaminants present react with the crystals ➤ it can only give an instantaneous reading not an average reading over the working period (TWA) ➤ the tubes are very fragile with a limited shelf life. 2.

3.

Passive sampling is measured over a full working period by the worker wearing a badge containing absorbent material. The material will absorb the contaminant gas and at the end of the measuring period, the sample is sent to a laboratory for analysis. The advantages of this method over the stain tube are that there is less possibility of instrument errors and it gives a time-weighted average reading (TWA). Sampling pumps and heads can be used to measure gases and dusts. The worker, whose breathing zone is being monitored, wears a collection head

Figure 14.8

4.

Hand pump and stain detector.

as a badge and a battery operated pump on his back at waist level. The pump draws air continuously through a ﬁlter, ﬁtted in the head, which will either absorb the contaminant gas or trap hazardous dust particles. After the designated testing period, it is sent to a laboratory for analysis. This system is more accurate than stain tubes and gives a TWA result but can be uncomfortable to wear over long periods. Such equipment can only be used by trained personnel. Direct reading instruments are available in the form of sophisticated analysers which can only be used by trained and experienced operatives. Infrared gas analysers are the most common but other types of analysers are also available. They are very accurate and give continuous or TWA readings. They tend to be very expensive and are normally hired or used by specialist consultants.

Other common monitoring instruments include vane anemometers used for measuring air ﬂow speeds and hygrometers which are used for measuring air humidity. Qualitative monitoring techniques include smoke tubes and the dust observation lamp. Smoke tubes generate a white smoke which may be used to indicate the direction of ﬂow of air – this is particularly useful when the air speed is very low or when testing the effectiveness of ventilation ducting. A dust observation lamp enables dust particles which are normally invisible to the human eye to be observed in the light beam. This dust is usually in the respirable range and, although the lamp does not enable any measurements of the dust to be made, it will illustrate the operation of a ventilation system and the presence of such dust. Regulation 10 requires routine sampling or monitoring of exposure where there could be serious health effects if the controls failed, exposure limits might be exceeded or the control measures may not be working properly. Air

235

Introduction to Health and Safety at Work monitoring should also be undertaken for any hazardous substances listed in Schedule 5 of the COSHH Regulations. Records of this monitoring should be kept for 5 years unless an employee is identiﬁable in the records in which case they should be kept for 40 years.

14.9 The control measures required under the COSHH Regulations 14.9.1 The principles of good practice for the control of exposure to substances hazardous to health The objective of the COSHH Regulations is to prevent ill-health due to the exposure to hazardous substances. Employers are expected to develop suitable and sufﬁcient control measures by: 1. 2. 3.

identifying hazards and potentially signiﬁcant risks taking action to reduce and control risks keeping control measures under regular review.

In order to assist employers with these duties, the HSE have produced the following eight principles of good practice: (a) Design and operate processes and activities to minimize the emission, release and spread of substances hazardous to health (b) Take into account all relevant routes of exposure – inhalation, skin absorption and ingestion – when developing control measures (c) Control exposure by measures that are proportionate to the health risk (d) Choose the most effective and reliable control options which minimize the escape and spread of substances hazardous to health (e) When adequate control of exposure cannot be achieved by other means, provide, in combination with other control measures, suitable personal protective equipment (f) Check and review regularly all elements of control measures for their continuing effectiveness (g) Inform and train all employees on the hazards and risks from the substances with which they work and the use of control measures developed to minimize the risks (h) Ensure that the introduction of control measures does not increase the overall risk to health and safety. All these principles are embodied in the following sections on COSHH control measures.

236

14.9.2 Hierarchy of control measures The COSHH Regulations require the prevention or adequate control of exposure by measures other than personal protective equipment, so far as is reasonably practicable, taking into account the degree of exposure and current knowledge of the health risks and associated technical remedies. The hierarchy of control measures are as follows: ➤ elimination ➤ substitution ➤ provision of engineering controls provision of supervisory (people) controls ➤ provision of personal protective equipment. Examples where engineering controls are not reasonably practicable include emergency and maintenance work, short-term and infrequent exposure and where such controls are not technically feasible. Measures for preventing or controlling exposure to hazardous substances include one or a combination of the following: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

elimination substitution total or partial enclosure of the process local exhaust ventilation dilute or general ventilation reduction of the number of employees exposed to a strict minimum reduced time exposure housekeeping training personal protective equipment welfare (including ﬁrst aid) medical records health surveillance.

14.9.3 Preventative control measures Prevention is the safest and most effective of the control measures and is achieved either by changing the process completely or by substituting for a less hazardous substance (the change from oil-based to water-based paints is an example of this). It may be possible to use a substance in a safer form, such as a brush paint rather than a spray. The EU has introduced a chemical safety regime REACH (Registration, Evaluation and Authorisation of Chemicals) Regulations which restricts the use of high risk substances or substances of very high concern and requires that safer substitute must be used. Manufacturers and importers of chemicals are responsible for understanding and managing the risks associated with their products.

Chemical and biological health hazards and control 14.9.4 Engineering controls The simplest and most efﬁcient engineering control is the segregation of people from the process and a chemical fume cupboard is an example of this as is the handling of toxic substances in a glove box. Modiﬁcation of the process is another effective control to reduce human contact with hazardous substances. More common methods, however, involve the use of forced ventilation – local exhaust ventilation and dilute ventilation.

Local exhaust ventilation Local exhaust ventilation removes the hazardous gas, vapour or fume at its source before it can contaminate the surrounding atmosphere and harm people working in the vicinity. Such systems are commonly used for the extraction of welding fumes and dust from woodworking machines. All exhaust ventilation systems have the following ﬁve basic components: 1.

a collection hood and intake – sometimes this is a nozzle-shaped point which is nearest to the workpiece, while at other times it is simply a hood placed over the workstation. The speed of the air entering the intake nozzle is important, if it is too low then hazardous fume may not be removed (air speeds of up to 1 m/s are normally required)

2.

3.

4.

5.

ventilation ducting – this normally acts as a conduit for the contaminated air and transports it to a ﬁlter and settling section. It is very important that this section is inspected regularly and any dust deposits removed. It has been known for ventilation ducting attached to a workshop ceiling to collapse under the added weight of metal dust deposits filter or other air cleaning device – normally located between the hood and the fan, the ﬁlter removes the contaminant from the air stream. The ﬁlter requires regular attention to remove contaminant and to ensure that it continues to work effectively fan – this moves the air through the system. It is crucial that the correct type and size of fan is ﬁtted to a given system and it should only be selected by a competent person. It should also be positioned so that it can easily be maintained but does not create a noise hazard to nearby workers exhaust duct – this exhausts the air to the outside of the building. It should be checked regularly to ensure that the correct volume of air is leaving the system and that there are no leakages. The exhaust duct should also be checked to ensure that there is no corrosion due to adverse weather conditions.

An Introduction to Local Exhaust Ventilation, HSG 37, HSE Books, is a very useful document on ventilation systems. The COSHH Regulations require that such ventilation systems must be inspected at least every 14 months by a competent person to ensure that they are still operating effectively. The effectiveness of a ventilation system will be reduced by damaged ducting, blocked or defective ﬁlters and poor fan performance. More common problems include the unauthorized extension of the system, poor initial design, poor maintenance, incorrect adjustments and a lack of inspection or testing. Routine maintenance should include repair of any damaged ducting, checking ﬁlters, examination of the fan blades to ensure that there has been no dust accumulation, tightening all drive belts and a general lubrication of moving parts. The local exhaust ventilation system will have an affect on the outside environment in the form of noise and odour. Both these problems can be reduced by regular routine maintenance of the fan and ﬁlter. The waste material from the ﬁlter may be hazardous and require the special disposal arrangements described later in the chapter (14.14.3)

Dilution (or general) ventilation Figure 14.9

Typical local exhaust and ventilation system.

Dilution (or general) ventilation uses either natural ventilation (doors and windows) or fan-assisted forced

237

Introduction to Health and Safety at Work

Figure 14.10

Natural ventilation in a building.

ventilation system to ventilate the whole working room by inducing a ﬂow of clean air, using extraction fans ﬁtted into the walls and the roof, sometimes assisted by inlet fans. It operates by either removing the contaminant or reducing its concentration to an acceptable level. It is used either when airborne contaminants are of low toxicity, low concentration and low vapour density or contamination occurs uniformly across the workroom. Paint spraying operations often use this form of ventilation as does the glass reinforced plastics (GRP) boat-building industry – these being instances where there are not discrete points of release of the hazardous substances. It is also widely used in kitchens and bathrooms. It is not suitable for dust extraction and where it is reasonably practicable to reduce levels by other means. There are limitations to the use of dilution ventilation. Certain areas of the work room (e.g. corners and beside cupboards) will not receive the ventilated air and a build-up of hazardous substances occurs. These areas are known as ‘dead areas’. The ﬂow patterns are also signiﬁcantly affected by doors and windows being opened or the rearrangement of furniture or equipment.

14.9.5 Supervisory or people controls Many of the supervisory controls required for COSHH purposes are part of a good safety culture and were discussed in detail in Chapter 4. These include items such as systems of work, arrangements and procedures, effective

238

communications and training. Additional controls when hazardous substances are involved are as follows: ➤ reduced time exposure – thus ensuring that workers have breaks in their exposure periods. The use of this method of control depends very much on the nature of the hazardous substance and its shortterm exposure limit (STEL) ➤ reduced number of workers exposed – only persons essential to the process should be allowed in the vicinity of the hazardous substance. Walkways and other trafﬁc routes should avoid any area where hazardous substances are in use ➤ eating, drinking and smoking must be prohibited in areas where hazardous substances are in use ➤ any special rules, such as the use of personal protective equipment, must be strictly enforced.

14.9.6 Personal protective equipment Personal protective equipment is to be used as a control measure only as a last resort. It does not eliminate the hazard and will present the wearer with the maximum health risk if the equipment fails. Successful use of personal protective equipment relies on good user training, the availability of the correct equipment at all times and good supervision and enforcement. The ‘last resort’ rule applies in particular to respiratory protective equipment (RPE) within the context of hazardous

Chemical and biological health hazards and control Types of personal protective equipment There are several types of personal protective equipment, such as footwear, hearing protectors and hard hats, which are not primarily concerned with protection from hazardous substances; those which are used for such protection, include: ➤ ➤ ➤ ➤

Figure 14.11

Personal protective equipment at work.

substances. There are some working conditions when RPE may be necessary: ➤ during maintenance operations ➤ as a result of a new assessment, perhaps following the introduction of a new substance ➤ during emergency situations, such as ﬁre or plant breakdown ➤ where alternatives are not technically feasible. All personal protective equipment, except respiratory protection equipment (which is covered by speciﬁc Regulations, such as COSHH, lead, etc.) is controlled by its own set of regulations – the Personal Protective Equipment at Work Regulations. A detailed summary of these Regulations is given in Chapter 17 and needs to be studied in detail with this section. The principal requirements of these regulations are as follows: ➤ personal protective equipment which is suitable for the wearer and the task ➤ compatibility and effectiveness of the use of multiple personal protective equipment ➤ a risk assessment to determine the need and suitability of proposed personal protective equipment ➤ a suitable maintenance programme for the personal protective equipment ➤ suitable accommodation for the storage of the personal protective equipment when not in use ➤ information, instruction and training for the user of personal protective equipment ➤ the supervision of the use of personal protective equipment by employees and a reporting system for defects.

respiratory protection hand and skin protection eye protection protective clothing.

For all types of personal protective equipment, there are some basic standards that should be reached. The personal protective equipment should ﬁt well, be comfortable to wear and not interfere either with other equipment being worn or present the user with additional hazards (e.g. impaired vision due to scratched eye goggles). Training in the use of particular personal protective equipment is essential, so that it is not only used correctly, but the user knows when to change an air ﬁlter or to change a type of glove. Supervision is essential with disciplinary procedures invoked for noncompliance with personal protective equipment rules. It is also essential that everyone who enters the proscribed area, particular senior managers, wear the speciﬁed personal protective equipment.

Respiratory protection equipment Respiratory protection equipment can be sub-divided into two categories – respirators (or face masks), which ﬁlter and clean the air, and breathing apparatus which supplies breathable air. Respirators should not be worn in air which is dangerous to health, including oxygen deﬁcient atmospheres. They are available in several different forms but the common ones are: ➤ a filtering half mask often called disposable respirator – made of the ﬁltering material. It covers the nose and mouth and removes respirable size dust particles. It is normally replaced after 8/10 hours of use. It offers protection against some vapours and gases ➤ a half mask respirator – made of rubber or plastic and covers the nose and mouth. Air is drawn through a replaceable ﬁlter cartridge. These can be used for vapours, gases or dusts but it is very important that the correct ﬁlter is used (a dust ﬁlter will not ﬁlter vapours) ➤ a full face mask respirator – similar to the half mask type but covers the eyes with a visor ➤ a powered respirator – a battery-operated fan delivers air through a ﬁlter to the face mask, hood, helmet or visor.

239

Introduction to Health and Safety at Work

Figure 14.12 Types of respiratory protective equipment. (a) Filtering half mask; (b) half mask reusable with filters; (c) compressed air the breathing apparatus with full face mask fitted with demand valve.

Breathing apparatus is used in one of three forms: ➤ self-contained breathing apparatus – where air is supplied from compressed air in a cylinder and forms a completely sealed system; ➤ fresh air hose apparatus – fresh air is delivered through a hose to a sealed face mask from an uncontaminated source. The air may be delivered by the wearer, by natural breathing or mechanically by a fan; ➤ compressed air line apparatus – air is delivered through a hose from a compressed air line. This can be either continuous ﬂow or on demand. The air must be properly ﬁltered to remove oil, excess water and other contaminants and the air pressure must be reduced. Special compressors are normally used. The selection of appropriate respiratory protective equipment and correct ﬁlters for particular hazardous substances is best done by a competent specialist person.

240

There are several important technical standards which must be considered during the selection process. Respiratory protective equipment must either be CE marked or HSE approved (HSE approval ceased on 30 June 1995 but such approved equipment may still be used). Other standards include the minimum protection required (MPR) and the assigned protection factor (APF). The CE mark does not indicate that the equipment is suitable for a particular hazard. The following information will be needed before a selection can be made: ➤ details of the hazardous substance in particular whether it is a gas, vapour or dust or a combination of all three ➤ presence of a beard or other facial hair which could prevent a good leak-free ﬁt (a simple test to see whether the ﬁt is tight or not is to close off the air supply, breathe in and hold the breath. The respirator

Chemical and biological health hazards and control

Figure 14.12

Continued.

should collapse onto the face. It should then be possible to check to see if there is a leak) ➤ the size and shape of the face of the wearer and physical ﬁtness ➤ compatibility with other personal protective equipment, such as ear defenders ➤ the nature of the work and agility and mobility required.

Hand and skin protection

Filters and masks should be replaced at the intervals recommended by the supplier or when taste or smell is detected by the wearer. All respiratory protective equipment should be examined at least once a month except for disposable respirators. A record of the inspection should be kept for at least 5 years. There should be a routine cleaning system in place and proper storage arrangements.

Hand and skin protection is mainly provided by gloves (arm shields are also available). A wide range of safety gloves is available for protection from chemicals, sharp objects, rough working and temperature extremes. Many health and safety catalogues give helpful guidance for the selection of gloves. For protection from chemicals, including paints and solvents, impervious gloves are recommended. These may be made of PVC, nitrile or neoprene. For sharp objects, such as trimming knives, a

Respiratory protective equipment – a practical guide for users, HSG 53, HSE Books, contains comprehensive advice and guidance on respiratory protective equipment selection, use, storage, maintenance and training and should be consulted for more information.

241

Introduction to Health and Safety at Work Kevlar based glove is the most effective. Gloves should be regularly inspected for tears or holes since this will obviously allow skin contact to take place. Another effective form of skin protection is the use of barrier creams and these come in two forms – pre-work and after-work. Pre-work creams are designed to provide a barrier between the hazardous substance and the skin. After-work creams are general purpose moisteners which replace the natural skin oils removed either by solvents or by washing.

Eye protection Eye protection comes in three forms – spectacles (safety glasses), goggles and face visors. Eyes may be damaged by chemical and solvent splashes or vapours, ﬂying particles, molten metals or plastics, non-ionizing radiation (arc welding and lasers) and dust. Spectacles are suitable for low-risk hazards (low speed particles such as machine swarf). Some protection against scratching of the lenses can be provided but this is the common reason for replacement. Prescription lenses are also available for people who normally wear spectacles. Goggles are best to protect the eyes from dust or solvent vapours because they ﬁt tightly around the eyes. Visors offer protection to the face as well as the eyes and do not steam up so readily in hot and humid environments. For protection against very bright lights, special light ﬁltering lenses are used (e.g. in arc welding). Maintenance and regular cleaning are essential for the efﬁcient operation of eye protection. When selecting eye protection, several factors need to be considered. These include the nature of the hazard (the severity of the hazard and its associated risk will determine the quality of protection required), comfort and user acceptability, compatibility with other personal protective equipment, training and maintenance requirements and costs.

Protective clothing Protective clothing includes aprons, boots and headgear (hard hats and bump caps). Aprons are normally made

Figure 14.13

242

Variety of eye protection goggles.

of PVC and protect against spillages but can become uncomfortable to wear in hot environments. Other lighter fabrics are available for use in these circumstances. Safety footwear protects against falling objects, collision with hard or sharp objects, hot or molten materials, slippery surfaces and against chemical spills. They have a metal toe-cap and come in the form of shoes, ankle boots or knee-length boots and are made of a variety of materials dependent on the particular hazard (e.g. thermally insulated against cold environments). They must be used with care near live unprotected electricity. Specialist advice is needed for use with ﬂammable liquids. It is important to note that appropriate personal protective equipment should be made available to visitors and other members of the public when visiting workplaces where hazardous substances are being used. It is also important to stress that managers and supervisors must lead by example, particularly if there is a legal requirement to wear particular personal protective equipment. Refusals by employees to wear mandatory personal protective equipment must lead to some form of disciplinary action.

14.10

Health surveillance and personal hygiene

Health surveillance enables the identiﬁcation of those employees most at risk from occupational ill-health. It should not be confused with health monitoring procedures such as pre-employment health checks or drugs and alcohol testing, but it covers a wide range of situations, from a responsible person looking for skin damage on hands to medical surveillance by a medical doctor. Health surveillance detects the start of an ill-health problem and collects data on ill-health occurrences. It also gives an indication of the effectiveness of the control procedures. Health surveillance is needed to protect workers, identify as early as possible any health changes related to exposure and warn of any lapses in control arrangements. Simple health surveillance is normally sufﬁcient for skin problems and takes the form of skin inspections by a ‘responsible person’. A ‘responsible person’ is a person who has been trained by a competent medical practitioner. It is required when there appears to be a reasonable chance that ill-health effects are occurring in a particular workplace as a result of reviewing sickness records or when a substance listed in Schedule 6 under Regulation 11 of the COSHH Regulations is being used. Schedule 6 lists the substances and the processes in which they are used. There is a limited number of such substances.

Chemical and biological health hazards and control Emergencies can range from fairly trivial spillages to major ﬁres involving serious air pollution incidents. The following points should be considered when emergency procedures are being developed:

Figure 14.14

Health commitment.

The health surveillance includes medical surveillance by an employment medical adviser or appointed doctor at intervals not exceeding 12 months. Records of the health surveillance must contain approved particulars and be kept for 40 years. The need for health surveillance is not common and further advice on the necessary procedures is available from the Employment Medical Advisory Service. Personal hygiene has already been covered under supervisory controls. It is very important for workers exposed to hazardous substances to wash their hands thoroughly before eating, drinking or smoking. Protection against biological hazards can be increased signiﬁcantly by vaccination (e.g. tetanus). Finally, contaminated clothing and overalls need to be removed and cleaned on a regular basis.

14.11

Maintenance and emergency controls

Engineering control measures will only remain effective if there is a programme of preventative maintenance available. Indeed the COSHH Regulations require that systems of adequate control are in place and the term ‘adequate control’ spans normal operations, emergencies and maintenance. Maintenance will involve the cleaning, testing and, possibly, the dismantling of equipment. It could involve the changing of ﬁlters in extraction plant or entering conﬁned spaces. It will almost certainly require hazardous substances to be handled and waste material to be safely disposed. It may also require a permit-to-work procedure to be in place since the control equipment will be inoperative during the maintenance operations. Records of maintenance should be kept for at least 5 years.

➤ the possible results of a loss of control (e.g. lack of ventilation) ➤ dealing with spillages and leakages (availability of effective absorbent materials) ➤ raising the alarm for more serious emergencies ➤ evacuation procedures, including the alerting of neighbours ➤ ﬁre-ﬁghting procedures and organization ➤ availability of respiratory protection equipment ➤ information and training. The Emergency Services should be informed of the ﬁnal emergency procedures and, in the case of the Fire Service, consulted for advice during the planning of the procedures. (See Chapter 6 for more details on emergency procedures.)

14.12

The transport of hazardous substances by road

Although this topic is not in the NEBOSH National General Certiﬁcate syllabus, a brief mention of the main precautions required to safeguard the health and safety of those directly involved in the transport of hazardous substances and of general members of the public is important. Data sheets from the manufacturer of the hazardous substance should indicate the safest method of handling it and will give information on emergency procedures (e.g. for spillages and ﬁre). These sheets should be available to all concerned with the transportation of the substance; in particular those responsible for loading/unloading, as well as the driver. The hazardous substance should be loaded correctly on the vehicle in suitable containers and segregated from incompatible materials. There must be adequate emergency information with the substance containers and attached to the vehicle. Drivers of the vehicles must receive special training which covers issues such as emergency procedures and route planning. There should also be emergency provisions for ﬁrst aid and personal protective equipment on the vehicle. Finally, the Transport of Dangerous Goods (Safety Adviser) Regulations require the appointment of a trained and competent safety adviser to ensure the safe loading, transportation and unloading of the hazardous substance. HSE have produced several guidance publications which offer more detailed advice on this topic.

243

Introduction to Health and Safety at Work 14.13

An illustrative example using COSHH controls

Organic solvents are widely used throughout industry and commerce in paints, inks, glues and adhesives. The COSHH hierarchy discussed under 14.9 should be applied to minimize the health risks from the use of these solvents. The top of this hierarchy is to eliminate or substitute the use of the organic solvent by using a less volatile or water-based alternative. If this is not possible, then some from of engineering control should be applied, such as dilution or local exhaust ventilation. Alternatively, the workplace, where the solvents are being used, could be enclosed or isolated from the main work activities. Other engineering type controls could include the use of properly labeled anti-spill containers, the use of covered disposal units for any used cloths and the transfer of large quantities using a pumping/pipe arrangements rather than simply pouring the solvent. Supervisory controls include the reduction in the length of time any employee is exposed to the solvent and the provision of good housekeeping, such as ensuring that containers are kept closed when not in use and any spills are quickly removed. The provision of barrier creams and personal protective equipment (eye protection, gloves and aprons) and respiratory protective equipment may also be required. Welfare issues will include ﬁrst aid provision, washing facilities and the encouragement of high levels of personal hygiene. Smoking and the consumption of food and drink should be prohibited where there might be contamination from organic solvents. All these supervisory items should be reinforced in training sessions and employees given appropriate information on the risks associated with the solvents. Finally, some form of health surveillance will be needed so that employees who show allergies to the solvents can be treated and, possibly, assigned other duties.

14.14

Environmental considerations

Organizations must also be concerned with aspects of the environment. There will be an interaction between the health and safety policy and the environmental policy which many organizations are now developing. Many of these interactions will be concerned with good practice, the reputation of the organization within the wider community and the establishment of a good health and safety culture. The health and safety data sheet, used for a COSHH assessment, also contains information of an environmental nature covering ecological information and disposal considerations.

244

There are three environmental issues which place statutory duties on employers and are directly related to the health and safety function. These are: ➤ air pollution ➤ water pollution ➤ waste disposal. The statutory duties are contained in the Environmental Protection Act (EPA) 1990 and several of its subsequent regulations. The Act is enforced by various state agencies (the Environment Agency, Local Authorities) and these agencies have very similar powers to the Health and Safety Executive (e.g. enforcement, prohibition notices and prosecution). The Act is divided into nine parts but this chapter will only be concerned with Part 1 (the control of pollution into the air, water or land) and Part 2 (waste disposal). Pollution is a term that covers more than the effect on the environment of atmospheric emissions, efﬂuent discharges and solid waste disposal from industrial processes. It also includes the effect of noise, vibration, heat and light on the environment. This was recognized in the 1996 EU Directive on Integrated Pollution Prevention and Control and The Pollution Prevention and Control Act 1999 replaced the Integrated Pollution Control Regulations made under Part 1 of the EPA by extending those powers to cover waste minimization, energy efﬁciency, noise and site restoration. Thus the Pollution Prevention and Control Act has now replaced Part 1 of the EPA.

14.14.1 Air pollution The most common airborne pollutants are carbon monoxide, benzene, 1,3-Butadiene, sulphur dioxide, nitrogen dioxide and lead. Air pollution is monitored by Integrated Pollution Prevention and Control (IPPC). This is a system which extends the Integrated Pollution Control (IPC) system established by Part 1 of the EPA by introducing three tiers of pollution control. ➤ Regime A1 Processes, which are certain largescale manufacturing processes with a potential to cause serious environmental damage to the air, water or the land. In England and Wales this is enforced by the Environment Agency. In Scotland there is a parallel system enforced by the Scottish Environmental Protection Agency. ➤ Regime A2 processes, which produce emissions to air, water and land with a much smaller potential to pollute than regime A1 processes. The local authority is the regulator for these processes.

Chemical and biological health hazards and control

To minimize the production of waste, emissions to air and noise.

To make efficient use of energy resources.

must have authorization. An operator of a prescribed process (such as a vehicle spray booth) must apply to the Environment Agency for prior authorization to operate the process. If the application is granted, the operator must monitor emissions and report them to the Environment Agency on a yearly basis. The Agency has the power to revoke the authorization, enforce the terms of the authorization or prohibit the operation of the process. Further information on the authorization process is given in Chapter 17.

14.14.2 Water pollution Figure 14.15

Environmental protection commitment.

➤ Part B processes, which may be classiﬁed as those from less polluting industries with only emissions released to air being subject to regulatory control. For such processes local authorities are the enforcing body through the Environmental Health Ofﬁcers and the system is known as Local Air Pollution Control (LAPC). This division has led to some anomalies in that some Part A processes create less pollution than some Part B processes. However, the grouping of three pollution destinations under one arrangement tends to a more holistic approach. The aim of IPPC is to control pollution of the whole environment under a single enforcement system and offers three principles to prevent and control pollution. These are: ➤ The ‘Best Practicable Environmental Option (BPEO)’ which considers both the environmental and economic costs and beneﬁts of the possible options available to deal with the pollution problem. BPEO is a legal requirement for Part A processes. It normally requires a technical solution. ➤ The ‘Best Available Techniques’ and is similar to BATNEEC (Best Available Techniques Not Entailing Excessive Cost) introduced by the EPA to minimize the overall environmental impact of a process. Part B processes only need satisfy the BATNEEC requirement which is not restricted to pollution control technology but can include employee training and competence and building design and maintenance ➤ As low as reasonably practicable applies the same test to an environmental problem as is applied to a health and safety problem. Any high or unacceptable environmental risk should be reduced to as low as is reasonably practicable. The EPA prescribes certain listed substances from being released to air, water or land. All prescribed processes

Pollution of rivers and other water courses can produce very serious effects on the health of plants and animals which rely on that water supply. The Environment Agency, is responsible for coastal waters, inland fresh water and ground waters (known as ‘controlled waters’). The EC Groundwater Directive seeks to protect ground water from pollution since this is a source of drinking water. Such sources can become polluted by leakage from industrial soakaways. Discharges to a sewer are controlled by the Water Industry Act that deﬁnes trade efﬂuent and those substances which are prohibited from discharge (e.g. petroleum spirit) and the Water Resources Act that covers discharge consent to controlled waters. It is an offence to pollute any controlled waters or sewage system. If hazardous substances are being used by the organization, safety data sheets give advice on the safe disposal of any residues that remain after the particular process has been completed. The local Water Company has a right to sample discharges into its sewers because it is required to keep a public trade efﬂuent register. There are two lists of prescribed substances which can only be discharged into a public sewer with the permission of the Water Company. Finally, if oil is stored on the premises, a retaining bund wall should surround the oil store. This will not only ensure that any oil leakage is contained but will also stop the contamination of ground water by ﬁre ﬁghting foam in the event of a ﬁre. This is a requirement of the Control of Pollution (Oil Storage) Regulations 2001.

14.14.3 Waste disposal The statutory duty of care for the management of waste derives from Part 2 of the EPA. The principal requirements are as follows: ➤ to handle waste so as to prevent any unauthorized escape into the environment ➤ to pass waste only to an authorized person as deﬁned by EPA

245

Introduction to Health and Safety at Work ➤ to ensure that a written description accompanies all waste. The Environmental Protection (Duty of Care) Regulations 1991 requires holders or producers of waste to complete a ‘Transfer Note’ giving full details of the type and quantity of waste for collection and disposal. Copies of the note should be kept for at least 2 years ➤ to ensure that no person commits an offence under the Act.

drains must be protected and bunds used to restrict spreading of the substance as a result of spills. A hierarchy for the management of waste streams has been recommended by the Environmental Agency:

The EPA is concerned with controlled waste. Controlled waste comprises household, industrial or commercial waste. It is a criminal offence to deposit controlled waste without a waste management licence and/or in a manner likely to cause environmental pollution or harm to human health. The EPA also covers ‘hazardous wastes’ which can only be disposed using special arrangements. These are sometimes substances which are life threatening (toxic, corrosive or carcinogenic) or highly ﬂammable. Clinical waste falls within this category. A consignment note system accompanies this waste at all the stages to its ﬁnal destination. Before hazardous waste is removed from the originating premises, a contract should be in place with a licensed carrier. Hazardous waste should be stored securely prior to collection to ensure that the environment is protected. The Hazardous Waste Regulations replace the Special Waste Regulations and cover many more substances; for example, computer monitors, ﬂuorescent tubes end-of-life vehicles and television sets. Hazardous waste is waste which can cause damage to the environment or to human health. Such waste is deﬁned in the List of Waste Regulations and producers of such waste may need to notify the Environment Agency. The Regulations seek to ensure that hazardous waste is safely managed and its movement is documented. The following points are important for construction sites:

3.

➤ Sites that produce more that 200 kg of hazardous waste each year for removal, treatment of disposal must register with the Environment Agency ➤ Different types of hazardous waste must not be mixed ➤ Producers must maintain registers of their hazardous wastes. Some form of training may be required to ensure that employees segregate hazardous and non-hazardous wastes on site and fully understand the risks and necessary safety precautions which must be taken. Personal protective equipment, including overalls, gloves and eye protection, must be provided and used. The storage site should be protected against trespassers, ﬁre and adverse weather conditions. If ﬂammable or combustible wastes are being stored, adequate ﬁre protection systems must be in place. Finally, in the case of liquid wastes, any

246

1.

2.

4.

5.

Prevention – by changing the process so that the waste is not produced (e.g. substitution of a particular material) Reduction – by improving the efﬁciency of the process (e.g. better machine maintenance) Reuse – by recycling the waste back into the process (e.g. using reground waste plastic products as a feed for new products) Recovery – by releasing energy through the combustion, recycling or composting of waste (e.g. the incineration of combustible waste to heat a building) Responsible disposal – by disposal in accordance with regulatory requirements.

In 1998, land disposal accounted for approximately 58% of waste disposal, 26% was recycled and the remainder was incinerated with some of the energy recovered as heat. The Producer Responsibility Obligations (Packaging Waste) Regulations 1997 placed legal obligations on employers to reduce their packaging waste by either recycling or recovery as energy (normally as heat from an incinerator attached to a district heating system). A series of targets have been stipulated which will reduce the amount of waste progressively over the years. These regulations are enforced by the Environment Agency which has powers of prosecution in the event of non-compliance. There is more information on the Environmental Protection Act (EPA), Integrated Pollution Prevention and Control (IPPC) and waste disposal in Chapter 17. The Environmental Agency has similar powers following the introduction of the Waste Electrical and Electronic Equipment (WEEE) directive, the Restrictions of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS) and the End of Life Vehicle (ELV) directive. The aim of the WEEE directive is to minimize the environmental impact of electrical and electronic equipment both during their lifetimes and when they are discarded. All electrical and electronic equipment must be returned to the retailer from its end user and reused or reprocessed by the manufacturer. Manufacturers must register with the Environment Agency who will advise on these obligations.

14.15

Practice NEBOSH questions for Chapter 14

1. Health hazards in the workplace may be transported by various chemical and biological agents.

Chemical and biological health hazards and control Describes THREE chemical and THREE biological hazardous agents giving an example in each case. 2. (a) Define the term ‘respirable dust’ (b) Outline methods used to measure the levels of airborne dust in the workplace. 3. For each of the following types of hazardous substance, give a typical example and state its primary affect on the body: (i) toxic (ii) corrosive (iii) carcinogenic (iv) irritant. 4. (a) Describe the differences between acute and chronic health effects (b) Identify the factors that could affect the level of harm experienced by an employee exposed to a toxic substance (c) Give TWO acute and TWO chronic health affects on the body from exposure to lead. 5. (a) Identify possible routes of entry of biological organisms into the body (b) Outline control measures that could be used to reduce the risk of infection from biological organisms. 6. (a) Define the term ‘target organ’ within the context of occupational health (b) Outline the personal hygiene practices that should be followed to reduce the risk of ingestion of a hazardous substance (c) Describe the respiratory defence mechanisms of the body against atmospheric dust.

10. For EACH of the following agents, outline the principal health affects AND identify a typical workplace situation in which a person might be exposed: (i) carbon monoxide (ii) silica (iii) legionella bacteria (iv) hepatitis virus. 11. For EACH of the following agents, outline the principal health affects AND identify a typical workplace situation in which a person might be exposed: (i) isocyanates (ii) asbestos (iii) leptospira bacteria (iv) lead. 12. (a) Identify TWO respiratory diseases that may be caused by exposure to asbestos (b) Identify the common sources of asbestos in buildings that should be considered when conducting an asbestos survey of work premises. 13. Outline the control measures that could be used to minimize the health risks from the use of organic solvents in the workplace. 14. (a) Outline the main requirements of the Control of Substances Hazardous to Health Regulations. (b) Brieﬂy outline a typical COSHH assessment of health risks as described by the regulations. 15. Outline the factors to be taken into account when undertaking an assessment of health risks from hazardous substances to be used in the workplace.

7. (a) Describe the typical symptoms of occupational dermatitis (b) Identify the factors that could affect the likelihood of dermatitis occurring in workers handling dermatitic substances.

16. (a) Explain the meaning of the term ‘workplace exposure limit’ (WEL) (b) Outline FOUR actions management could take when a WEL has been exceeded.

8. In relation to occupational dermatitis: (i) identify TWO common causative agents (ii) describe the typical symptoms of the condition (iii) state the sources of information that may help to identify dermatitic substances in the workplace (iv) outline speciﬁc measures designed to prevent the occurrence of occupational dermatitis.

17. A engineering company has noticed a recent increase in work-related ill health amongst shop ﬂoor workers who use a degreasing solvent for which a workplace exposure limit (WEL) has been assigned. (i) Explain the meaning of the term ‘workplace exposure limit’ (WEL) (ii) Give reasons for the possible increase in work-related ill health amongst the shop ﬂoor workers.

9. (a) Explain the health and safety beneﬁts of restricting smoking in the workplace (b) Outline the ways in which an organization could effectively implement a no-smoking policy.

18. Identify the information that should be included on a manufacturer’s safety data sheet supplied with a hazardous substance.

247

Introduction to Health and Safety at Work 19. The manager of a company is concerned about a substance to be introduced into one of its manufacturing processes. Outline FOUR sources of information that might be consulted when assessing the risk from this substance. 20. (a) Describe, by means of a labelled sketch, a chemical indicator (stain detector) tube suitable for atmospheric monitoring (b) List the main limitations of chemical indicator (stain detector) tubes. 21. (a) List FOUR respiratory diseases that could be caused by exposure to dust at work (b) Identify the possible indications of a dust problem in a workplace. 22. An essential raw material for a process is delivered in powdered form and poured by hand from bags into a mixing vessel. Outline the control measures that might be considered in this situation in order to reduce employee exposure to the substance. 23. (a) Describe how the body may defend itself against the harmful effects of airborne dust (b) Outline, using practical examples where appropriate, the control measures that may be used to reduce levels of dust in a work environment. 24. Outline the factors that need to be considered when managing the risk of exposure to hazardous chemicals at work. 25. An employees is engaged in general cleaning activities in a large veterinary practice. (i) Identify FOUR speciﬁc types of hazard that the cleaner might face when undertaking the cleaning (ii) Outline the precautions that could be taken to minimize the risk of harm from these hazards. 26. A furniture factory uses solvent-based adhesives in its manufacturing process. (i) Identify the possible affects on the health of employees using the adhesives (ii) State FOUR control measures to minimize such health effects. 27. An employee is required to install glass-ﬁbre insulation in a loft. (i) Identify FOUR hazards connected with this activity (ii) Outline the precautions that might be taken to minimize harm to the employee carrying out this operation.

248

28. Outline the precautions to ensure the health and safety of persons engaged in paint spraying in a motor vehicle repair shop. 29. (a) Explain the meaning of the term ‘dilution ventilation’ (b) Outline the circumstances in which the use of dilution ventilation may be appropriate. 30. A local exhaust ventilation (LEV) system is used to extract welding fume from the working environment in a fabrication workshop. (i) Ouline the factors that might reduce the effectiveness of the LEV system (ii) Identify the possible affects that the use of the LEV system may have on the local and wider environment. 31. Local exhaust ventilation (LEV) systems must be thoroughly examined at least every 14 months. Outline the routine maintenance that should be carried out between statutory examinations in order to ensure the continuing efﬁciency of a LEV system. 32. (a) Outline the requirements of the Personal Protective Equipment at Work Regulations (b) Outline the factors which should be considered when selecting personal protective equipment. 33. An organization uses various types of personal protective equipment (PPE). Outline the general issues relating to the selection and use of PPE that will help to ensure its effectiveness in controlling hazards. 34. (a) Explain the difference between breathing apparatus and respirators (b) Outline the main limitations of a half-mask re-usable respirator. 35. (a) Identify the types of hazard against which gloves could offer protection (b) Outline the practical limitations of using gloves as a means of protection. 36. (a) Identify THREE types of hazard for which personal eye protection would be required (b) Outline the range of issues that should be addressed when training employees in the use of personal eye protection. 37. (a) Identify ONE advantage and ONE disadvantage of safety goggles compared with safety spectacles (b) Outline SIX factors to be considered in the selection of eye protection for use at work.

Chemical and biological health hazards and control 38. Identify FOUR different types of hazard that may necessitate the use of special footwear, explaining in EACH case how the footwear affords protection. 39. (a) Outline the health and safety risks associated with welding operations (b) Outline the factors to be considered in the selection of respiratory protective equipment for persons carrying out welding activities. 40. Outline the meaning of the term ‘health surveillance’ as described by the Control of Substances Hazardous to Health Regulations. 41. A large item of process machinery is to be cleaned manually with a ﬂammable solvent before being partially dismantled for repair. (i) Identify FOUR possible health effects from exposure to the solvent (ii) Outline the safety precautions that should be taken when using such ﬂammable solvents (iii) Outline further precautions that might be needed in order to ensure the health and safety of those carrying out the maintenance work.

44. A company produces a range of solid and liquid wastes, both hazardous and non-hazardous. Outline the arrangements that should be in place to ensure the safe storage of the wastes prior to their collection and disposal. 45. Absorbent mats and granules have been used to soak up a chemical spillage. Outline the issues that will need to be considered in relation to the handling, temporary storage and ﬁnal disposal of the waste material. 46. Outline the issues that should be addressed by an organization when developing a system for the safe collection and disposal of waste. 47. Outline the hazards that may be encountered by refuse collectors employed to remove waste from domestic premises and load it into a refuse vehicle. 48. Identify EIGHT safe practices to be followed when using a skip for the collection and removal of waste from a construction site.

42. Outline the main precautions to be taken to ensure the safe transport of hazardous substances by road. 43. In relation to the spillage of a toxic substance from a ruptured drum stored in a warehouse: (i) Identify THREE ways in which persons working in close vicinity to the spillage might be harmed (ii) Outline a procedure to be adopted in the event of such a spillage.

249

Physical and psychological health hazards and control

15.1 Introduction Occupational health is concerned with physical and psychological hazards as well as chemical and biological hazards. The physical occupational hazards have been well-known for many years and the recent emphasis has been on the development of lower risk workplace environments. Physical hazards include topics such as electricity and manual handling which were covered in earlier chapters and noise, display screen equipment and radiation which are discussed in this chapter. However, it is only really in the last twenty years that psychological hazards have been included among the occupational health hazards faced by many workers. This is now the most rapidly expanding area of occupational health and includes topics such as mental health and workplace stress, violence to staff, passive smoking, drugs and alcohol. The physical and psychological hazards discussed in this chapter are covered by the following health and safety regulations: ➤ Workplace (Health, Safety and Welfare) Regulations ➤ Health and Safety (Display Screen Equipment) Regulations ➤ Manual Handling Operations Regulations ➤ Noise at Work Regulations ➤ Ionising Radiations Regulations

15.2 Task and workstation design 15.2.1

The principles and scope of ergonomics

Ergonomics is the study of the interaction between workers and their work in the broadest sense, in that it

250

15

encompasses the whole system surrounding the work process. It is, therefore, as concerned with the work organization, process and design of the workplace and work methods as it is with work equipment. The common deﬁnitions of ergonomics, the ‘man–machine interface’ or ‘ﬁtting the man to the machine rather than vice versa’ are far too narrow. It is concerned about the physical and mental capabilities of an individual as well as their understanding of the job under consideration. Ergonomics includes the limitations of the worker in terms of skill level, perception and other personal factors in the overall design of the job and the system supporting and surrounding it. It is the study of the relationship between the worker, the machine and the environment in which it operates and attempts to optimize the whole worksystem, including the job, to the capabilities of the worker so that maximum output is achieved for minimum effort and discomfort by the worker. Cars, buses and lorries are all ergonomically designed so that all the important controls, such as the steering wheel, brakes, gear stick and instrument panel are easily accessed by most drivers within a wide range of sizes. Ergonomics is sometimes described as human engineering and as working practices become more and more automated, the need for good ergonomic design becomes essential. The scope of ergonomics and an ergonomic assessment is very wide incorporating the following areas of study: ➤ personal factors of the worker, in particular physical, mental and intellectual abilities, body dimensions and competence in the task required ➤ the machine and associated equipment under examination ➤ the interface between the worker and the machine – controls, instrument panel or gauges and any aids including seating arrangements and hand tools

Physical and psychological health hazards and control

Figure 15.1

Workstation ergonomic design improvements.

➤ environmental issues affecting the work process such as lighting, temperature, humidity, noise and atmospheric pollutants ➤ the interaction between the worker and the task, such as the production rate, posture and system of working ➤ the task or job itself – the design of a safe system of work, checking that the job is not too strenuous or repetitive and the development of suitable training packages ➤ the organization of the work, such as shift work, breaks and supervision. The reduction of the possibility of human error is one of the major aims of ergonomics and an ergonomic assessment. An important part of an ergonomic study is to design the workstation or equipment to ﬁt the worker. For this to be successful, the physical measurement of the human body and an understanding of the variations in these measurements between people is essential. Such a study is known as anthropometry, which is deﬁned as the scientiﬁc measurement of the human body and its movement. Since there are considerable variations in, for example, the heights of people, it is common for some part of the workstation to be variable (e.g. an adjustable seat).

15.2.2

The ill-health effects of poor ergonomics

Ergonomic hazards are those hazards to health resulting from poor ergonomic design. They generally fall within the physical hazard category and include the manual handling and lifting of loads, pulling and pushing loads, prolonged periods of repetitive activities and work with vibrating tools. The condition of the working environment, such as low lighting levels, can present health hazards to the eyes. It is also possible for psychological conditions, such as occupational stress, to result from ergonomic hazards.

The common ill-health effects of ergonomic hazards are musculoskeletal disorders (back injuries, covered in Chapter 10, and work-related upper limb disorders (WRULDs) including repetitive strain injury being the main disorders) and deteriorating eyesight.

Work Related Upper Limb Disorders (WRULDs) WRULDs describe a group of illnesses which can affect the neck, shoulders, arms, elbows, wrists, hands and ﬁngers. Tenosynovitis (affecting the tendons), carpal tunnel syndrome (affecting the tendons which pass through the carpal bone in the hand) and frozen shoulder are all examples of WRULDs which differ in the manifestation and site of the illness. The term repetitive strain injury (RSI) is commonly used to describe WRULDs. WRULDs are caused by repetitive movements of the ﬁngers, hands or arms which involve pulling, pushing, reaching, twisting, lifting, squeezing or hammering. These disorders can occur to workers in ofﬁces as well as in factories or on construction sites. Typical occupational groups at risk include painters and decorators, riveters and pneumatic drill operators and desk top computer users. The main symptoms of WRULDs are aching pain to the back, neck and shoulders, swollen joints and muscle fatigue accompanied by tingling, soft tissue swelling, similar to bruising, and a restriction in joint movement. The sense of touch and movement of ﬁngers may be affected. The condition is normally a chronic one in that it gets worse with time and may lead eventually to permanent damage. The injury occurs to muscle, tendons and/or nerves. If the injury is allowed to heal before being exposed to the repetitive work again, no long-term damage should result. However, if the work is repeated again and again, healing cannot take place and permanent damage can result leading to a restricted blood ﬂow to the arms, hands and ﬁngers.

251

Introduction to Health and Safety at Work

Figure 15.2

Poor workstation layout may cause WRULD.

The risk factors, which can lead to the onset of WRULDs, are repetitive actions of lengthy duration, the application of signiﬁcant force and unnatural postures, possibly involving twisting and over-reaching and the use of vibrating tools. Cold working environments, work organization and worker perception of the work organization have all been shown in studies to be risk factors, as is the involvement of vulnerable workers such as those with pre-existing ill-health conditions and pregnant women.

cases, gangrene can develop leading to the amputation of the affected hand or ﬁnger. VWF was ﬁrst detailed as an industrial disease in 1911. The risk of developing HAVS depends on the frequency of vibration, the length of exposure and the tightness of the grip on the machine or tool. Some typical values of vibration measurements for common items of equipment used in industry are given in Table 15.1.

Whole-body vibration (WBV) Ill-health due to vibrations Hand-held vibrating machinery (such as pneumatic drills, sanders and grinders, powered lawn mowers and strimmers and chainsaws) can produce health risks from hand–arm or whole body vibrations.

Hand–arm vibration syndrome (HAVS) HAVS describes a group of diseases caused by the exposure of the hand and arm to external vibration. Some of these have been described under WRULDs, such as carpal tunnel syndrome. However, the best known disease is vibration white finger (VWF) in which the circulation of the blood, particularly in the hands, is adversely affected by the vibration. The early symptoms are tingling and numbness felt in the ﬁngers, usually some time after the end of the working shift. As exposure continues, the tips of the ﬁngers go white and then the whole hand may become affected. This results in a loss of grip strength and manual dexterity. Attacks can be triggered by damp and/or cold conditions and, on warming, ‘pins and needles’ are experienced. If the condition is allowed to persist, more serious symptoms become apparent including discoloration and enlargement of the ﬁngers. In very advanced

252

WBV is caused by vibration from machinery passing into the body either through the feet of standing workers or the buttocks of sitting workers. The most common ill-health affect is severe back pain which, in severe cases, may result in permanent injury. Other acute affects include reduced visual and manual control, increased heart rate and blood pressure. Chronic or long-term affects include permanent spinal damage, damage to the central nervous system, hearing loss and circulatory and digestive problems. The most common occupations which effect WBV, are driving fork lift trucks, construction vehicles and agricultural or horticultural machinery and vehicles. There is growing concern throughout the European Union about this problem. Control measures include the proper use of the equipment including correct adjustments of air or hydraulic pressures, seating and, in the case of vehicles, correct suspension, tyre pressures and appropriate speeds to suit the terrain. Other control measures include the selection of suitable equipment with low vibration characteristics, work rotation, good maintenance and fault reporting procedures. HSE commissioned measurements of WBV on several machines and some of the results are shown in Table 15.2

Physical and psychological health hazards and control Table 15.1 Examples of vibration exposure values measured by HSE on work equipment

Preventative and precautionary measures The control strategy outlined in Chapter 6 can certainly be applied to ergonomic risks. The common measures used to control ergonomic ill-health effects are:

Equipment

Condition

Vibration Reading (m/s2)

Road Breakers

Typical Modern design and trained operator Worst tools and operating conditions

12 5

Demolition hammers

Modern Tools Typical Worst tools

8 15 25

Hammer drills

Typical Best tools and operating conditions Worst tools and operating conditions

9 6

Machine

Activity

Vibration reading (m/s2)

25

3 tonne articulated site

Removal of spoil

0.78

Modern vibrationreduced designs Other types

4

Dumper truck

Transport of soil

1.13

8

Transport of soil

0.91

Small angle grinders

Typical

2–6

25 tonne articulated dumper truck Bulldozer

Dozing

1.16

Chainsaws

Typical

6 0.86

Typical Best

4 2

4 tonne Twin-drum

Finishing tarmac

Brush cutter or strimmer

1.03

Typical

7–10

80 tonne Rigid Dumper Truck

Transport of soil

Sanders (orbital)

Large angle grinders

➤ results of task analysis and identiﬁcation of repetitive actions ➤ the elimination of vibrating or hazardous tasks by performing the job in a different way

20

Table 15.2 Machines which could produce significant whole-body vibration

Regular exposure to HAV can cause a range of permanent injuries to hands and arms, collectively known as hand-arm vibration syndrome (HAVS). The injuries can incluse damage to the: Blood circulatory system (e.g. vicbration white finger);

Pins and needles Sensory nerves;

Severe pain and numbness Muscles; Bones; Joints

Loss of sense of touch

Loss of grip strength

Painful wrist (carpal tunnel syndrome)

Figure 15.3

Injuries which can be caused by hand-arm vibration.

253

Introduction to Health and Safety at Work ➤ ensure that the correct equipment (properly adjusted) is always used ➤ introduce job rotation so that workers have a reduced time exposure to the hazard ➤ during the design of the job ensure that poor posture is avoided ➤ undertake a risk assessment ➤ reports from employees and safety representatives ➤ ill-health reports and absence records ➤ introduce a programme of health surveillance ➤ ensure that employees are given adequate information on the hazards and develop a suitable training programme ➤ ensure that a programme of preventative maintenance is introduced and include the regular inspection of items such as vibration isolation mountings, and ➤ keep up-to-date with advice from equipment manufacturers, trade associations and health and safety sources (more and more low vibration equipment is becoming available). A very useful and extensive checklist for the identiﬁcation and reduction of work-related upper limb disorders is given in Appendix 2 of the HSE Guide to work-related upper limb disorders HSG 60. HSE have also produced two very useful guides – Hand-arm vibration, The Control of Vibration at Work Regulations 2005 Guidance on Regulations L140 and Whole-body vibration, The Control of Vibration at Work Regulations 2005 Guidance on Regulations L141. These guidance documents offer detailed advice on the implementation of the regulations.

15.2.3

The Control of Vibration at Work Regulations 2005

The Control of Vibration at Work Regulations introduce, for both hand-arm and whole-body vibration, a daily exposure limit and action values. These values are as follows: 1.

2.

For hand-arm vibration (a) the daily exposure limit value normalized to an 8-hour reference period is 5 m/s2 (b) the daily exposure action value normalized to an 8-hour reference period is 2.5 m/s2 For whole-body vibration (a) the daily exposure limit value normalized to an 8-hour reference period is 1.15 m/s2 (b) the daily exposure action value normalized to an 8-hour reference period is 0.5 m/s2

An exposure limit value must not be exceeded. If an exposure action value is exceeded, then action must be taken to reduce the value. The expression A(8) is added to the exposure limit or action value to denote that it is an average value spread over an 8-hour working day. Thus the daily exposure limit value for hand-arm vibration is 5 m/s2 A(8).

Hand-arm vibration Many machines and processed used in industry produce hand-arm vibration. Typical high risk processes include: ➤ ➤ ➤ ➤ ➤

grinding, sanding and polishing wood and stone cutting stone, metal and wood riveting, caulking and hammering compacting sand, concrete and aggregate drilling and breaking rock, concrete and road surfaces, and ➤ surface preparation, including de-scaling and paint removal. There are several ways to ascertain the size of the vibration generated by equipment and machines. Manufacturers must declare vibration emission values for portable hand-held and hand guided machines and provide information on risks. Other important sources for vibration information include scientiﬁc and technical journals, trade associations and on-line databases. HSE experience has shown that the vibration level is higher in practice than that quoted by many manufacturers. The reasons for this discrepancy may be that:

Figure 15.4

254

Mounted breaker to reduce vibrations.

➤ the equipment is not well maintained ➤ the equipment is not suitable for the material being worked ➤ the accessories are not appropriate or badly ﬁtted, or ➤ the operative is not using the tool properly.

Physical and psychological health hazards and control Table 15.3

The change in exposure times as vibration increase

Value of vibration (m/s2)

2.5

3.5

5

7

10

14

20

Exposure time to reach action value (hours)

8

4

2

1

30 min

15 min

8 min

Exposure time to reach limit value (hours)

over 24

16

8

4

2

1

30 min

In view of these problems, it is recommended that the declared value should be doubled when comparisons are made with exposure limits. Since the exposure limit or action value is averaged over 8 hours, it is possible to work with higher values for a reduced exposure time. Table 15.3 shows the reduction in exposure time as the size of the vibration increases. The Guidance (L140) gives very useful advice on the measurement of vibration, undertaking a suitable and sufﬁcient risk assessment, control measures, health surveillance and training of employees. The following points summarise the important measures which should be taken to reduce the risks associated with hand-arm vibration: 1. 2.

3.

4. 5.

6.

avoid, whenever possible, the need for vibration equipment undertake a risk assessment which includes a soundly based estimate of the employees’ exposure to vibration develop a good maintenance regime for tools and machinery. This may involve ensuring that tools are regularly sharpened, worn components are replaced or engines are regularly tuned and adjusted introduce a work pattern that reduces the time exposure to vibration issue employees with gloves and warm clothing. There is a debate as to whether anti-vibration gloves are really effective but it is agreed that warm clothing helps with blood circulation which reduces the risk of vibration white ﬁnger. Care must be taken so that the tool does not cool the hand of the operator, and introduce a reporting system for employees to use so that concerns and any symptoms can be recorded and investigated.

been caused by other activities but WBV will aggravate it. The reasons for back pain in drivers include: ➤ poor posture while driving ➤ incorrect adjustment of the driver’s seat ➤ difﬁculty in reaching all relevant controls due to poor design of the controls layout ➤ frequent manual handling of loads, and ➤ frequent climbing up and down from a high cab. The regulations require that where there is a likelihood of WBV, the employer must undertake a risk assessment. The HSE Guidance document, L141, gives detailed advice to help with this risk assessment and on estimating daily exposure levels. Whole-body vibration risks are low for exposures around the action value and usually only simple control measures are necessary. The regulations allow a transitional period for the limit value until July 2010 for vehicles supplied before July 2007. The measurement of WBV is very difﬁcult and may only be measured accurately by a specialist competent person. If the risk assessment has been made and the recommended control actions are in place, there is no need to measure the exposure of employees to vibration. However, HSE have suggested that employers can use the following checklist to estimate whether exposure to WBV is high: 1. 2. 3. 4.

Whole-body vibration (WBV) Whole-body vibration in industry arises from driving vehicles, such as tractors or fork lift trucks, over rough terrain or uneven ﬂoors. It is highly unlikely that driving vehicles on smooth roads will produce WBV problems. As explained earlier, the most common health problem associated with WBV is back pain. This pain may well have

5. 6. 7. 8.

There is a warning in the machine manufacturer’s handbook that there is a risk of WBV The task is not suitable for the machine or vehicle being used Operators or drivers are using excessive speeds or operating the machine too aggressively Operators or drivers are working too many hours on machines or vehicles that are prone to WBV Road surfaces are too rough and potholed or ﬂoors uneven Drivers are being continuously jolted or when going over bumps rising from their seats Vehicles designed to operate on normal roads are used on rough or poorly repaired roads Operators or drivers have reported back problems.

255

Introduction to Health and Safety at Work If one or more of the above applies, then exposure to WBV may be high. The actions for controlling the risks from WBV include the following: Ensure that: ➤ the driver’s seat is correctly adjusted so that all controls can be reached easily and that the driver weight setting on their suspension seat, if available, is correctly adjusted. The seat should have a back rest with lumbar support ➤ anti-fatigue mats are used if the operator has to stand for long periods ➤ the speed of the vehicle is such that excessive jolting is avoided. Speeding is one of the main causes of excessive whole-body vibration ➤ all vehicle controls and attached equipment are operated smoothly ➤ only established site roadways are used ➤ only suitable vehicles and equipment are selected to undertake the work and cope with the ground conditions ➤ the site roadway system is regularly maintained ➤ all vehicles are regularly maintained with particular attention being paid to tyre condition and pressures, vehicles suspension systems and the driver’s seat ➤ work schedules are regularly reviewed so that long periods of exposure on a given day are avoided and drivers have regular breaks

➤ prolonged exposure to WBV is avoided for at risk groups (older people, young people, people with a history of back problems and pregnant women) and ➤ employees are aware of the health risks from WBV, the results of the risk assessment and the ill-health reporting system. They should also be trained to drive in such a way that excessive vibration is reduced. A simple health monitoring system that includes a questionnaire checklist should be agreed with employees or their representatives (available on the HSE website) to be completed once a year by employees at risk. More information on the Control of Vibration at Work Regulations is given in Chapter 17.

15.2.4

Display screen equipment (DSE)

Display screen equipment, which includes visual display units, is a good example of a common work activity which relies on an understanding of ergonomics and the ill-health conditions which can be associated with poor ergonomic design. Legislation governing DSE is covered by the Health and Safety (Display Screen Equipment) Regulations 1992 and a detailed summary of them is given in Chapter 17. The regulations apply to a user or operator of DSE and deﬁne a user or operator. The deﬁnition is not as tight as many employers would like it to be, but usage in excess of approximately one hour continuously each day would

Seating and posture for typical office tasks Forearms approximately horizontal Seat back adjustability

Minimal extension, flexion or deviation of wrist

Screen height and angle should allow comfortable head position

Good lumbar support

Seat height adjustability

Space in front of the keyboard to support hands or wrists during pauses in keying Space for postural change – no obstacles under desk

No execess pressure on underside of thighs and backs of knees

Figure 15.5

256

Workstation design.

Foot support if required

Physical and psychological health hazards and control deﬁne a user. The deﬁnition is important since users are entitled to free eye tests and, if required, a pair of spectacles. The basic requirements of the regulations are: ➤ a suitable and sufﬁcient risk assessment of the workstation, including the software in use, trip and electrical hazards from trailing cables and the surrounding environment ➤ workstation compliance with the minimum speciﬁcations laid down in the schedules appended to the regulations ➤ a plan of the work programme to ensure that there are adequate breaks in the work pattern of workers ➤ the provision of free eye sight tests and, if required, spectacles to users of DSE ➤ a suitable programme of training and sufﬁcient information given to all users. There are three basic ill-health hazards associated with DSE. These are: ➤ musculoskeletal problems ➤ visual problems ➤ psychological problems. A fourth hazard, of radiation, has been shown from several studies to be very small and is now no longer normally considered in the risk assessment. Similarly, in the past, there have been suggestions that DSE could cause epilepsy and there were concerns about adverse health effects on pregnant women and their unborn children. All these risks have been shown in various studies to be very low.

Musculoskeletal problems Tenosynovitis is the most common and well-known problem which affects the wrist of the user. The symptoms and effects of this condition have already been covered. Sufﬁce it to say that if the condition is ignored, then the tendon and tendon sheath around the wrist will become permanently injured. Tenosynovitis, better known as RSI, is caused by the continual use of a keyboard and can be relieved by the use of wrist supports. Other WRULDs are caused by poor posture and can produce pains in the back, shoulders, neck or arms. Less commonly, pain may also be experienced in the thighs, calves and ankles. These problems can be mitigated by the application of ergonomic principles in the selection of working desks, chairs, foot rests and document holders. It is also important to ensure that the desk is at the correct height and the computer screen is tilted at the correct angle to avoid putting too much strain on the neck. (Ideally the user should look down on the screen at a slight angle.)

The keyboard should be detachable so that it can be positioned anywhere on the desktop and a correct posture adopted while working at the keyboard. The chair should be adjustable in height, stable and have an adjustable backrest. If the knees of the user are lower than the hips when seated, then a footrest should be provided. The surface of the desk should be non-reﬂecting and uncluttered but ancillary equipment (e.g. telephone and printer) should be easily accessible.

Visual problems There does not appear to be much medical evidence that DSE causes deterioration in eye sight, but many users suffer from visual fatigue which results in eye strain, sore eyes and headaches. Less common ailments are skin rashes and nausea. The use of DSE may indicate that reading spectacles are needed and the Regulations make provision for this. It is possible that any prescribed lenses may only be suitable for DSE work since they will be designed to give optimum clarity at the normal distance at which screens are viewed (50–60 cm). Eye strain is a particular problem for people who spend a large proportion of their working day using display screen equipment. A survey has indicated that up to 90% of DSE users complain of eye fatigue. Unnecessary eye strain can be reduced by the following additional steps to those already identiﬁed in this section: ➤ Train staff in the correct use of the equipment ➤ Ensure that a font size of at least 12 is used on the screen, and ➤ Ensure that users take regular breaks away from the screen (every 20 minutes). The screen should be adjustable in tilt angle and screen brightness and contrast. Finally, the lighting around the workstation is important. It should be bright enough to allow documents to be read easily but not too bright so that either headaches are caused or there are reﬂective glares on the computer screen.

Psychological problems These are generally stress-related problems. They may have environmental causes, such as noise, heat, humidity or poor lighting, but they are usually due to high speed working, lack of breaks, poor training and poor workstation design. One of the most common problems is the lack of understanding of all or some of the software packages being used. There are several other processes and activities where ergonomic considerations are important. These include the assembly of small components (microelectronics

257

Introduction to Health and Safety at Work assembly lines) and continually moving assembly lines (car assembly plants). Many of these processes including some of the chemical hazards (such as soldering fumes) are described in the previous chapter.

15.3 Welfare and work environment issues Welfare and work environment issues are covered by the Workplace (Health, Safety and Welfare) Regulations 1992 together with an Approved Code of Practice and add-itional guidance.

15.3.1

Welfare

Welfare arrangements include the provision of sanitary conveniences and washing facilities, drinking water, accommodation for clothing, facilities for changing clothing and facilities for rest and eating meals. First-aid provision is also a welfare issue, but is covered in Chapter 6. Sanitary conveniences and washing facilities must be provided together and in a proportion to the size of the workforce. The Approved Code of Practice provides two tables offering guidance on the requisite number of water closets, wash stations and urinals for varying sizes of workforce (approximately one of each for every 25 employees). Special provision should be made for disabled workers and there should normally be separate facilities for men and women. A single convenience would only be acceptable if it were situated in a separate room whose door could be locked from the inside. There should be adequate protection from the weather and only as a last resort should public conveniences be used. A good supply of warm water, soap and towels must be provided as close to the sanitary facilities as possible. The facilities should be well lit and ventilated and their walls and ﬂoors easy to clean. It may be necessary to install a shower for certain types of work. Hand dryers are permitted but there are concerns about their effectiveness in drying hands completely and thus removing all bacteria. In the case of temporary or remote worksites, sufﬁcient chemical closets and sufﬁcient washing water in containers must be provided. All such facilities should be well ventilated and lit and cleaned regularly. Drinking water must be readily accessible to all the workforce. The supply of drinking water must be adequate and wholesome. Normally mains water is used and should be marked as ‘drinking water’ if water not ﬁt for drinking is also available. Accommodation for clothing and facilities for changing clothing must be provided which is clean,

258

warm, dry, well-ventilated and secure. Where workers are required to wear special or protective clothing, arrangements should be such that the workers’ own clothing is not contaminated by any hazardous substances. Facilities for rest and eating meals must be provided so that workers may sit down during break times in areas where they do not need to wear personal protective equipment. From 1 July 2007 smoking was banned inside public premises (see Appendix 15.1). Facilities should also be provided for pregnant women and nursing mothers to rest. Arrangements must be in place to ensure that food is not contaminated by hazardous substances.

15.3.2

Workplace environment

The issues governing the workplace environment are ventilation, heating and temperature, lighting, workstations and seating.

Ventilation Ventilation of the workplace should be effective and sufﬁcient and free of any impurity and air inlets should be sited clear of any potential contaminant (e.g. a chimney ﬂue). Care needs to be taken to ensure that workers are not subject to uncomfortable draughts. The ventilation plant should have an effective visual or audible warning device ﬁtted to indicate any failure of the plant. The plant should be properly maintained and records kept. The supply of fresh air should not normally fall below 5 to 8 litres per second per occupant.

Heating and temperature During working hours, the temperature in all workplaces inside buildings shall be reasonable (not uncomfortably high or low). ‘Reasonable’ is deﬁned in the Approved Code of Practice as at least 16ºC, unless much of the work involves severe physical effort in which case the temperature should be at least 13ºC. These temperatures refer to readings taken close to the workstation at working height and away from windows. The Approved Code of Practice recognizes that these minimum temperatures cannot be maintained where rooms open to the outside or where food or other products have to be kept cold. A heating or cooling method must not be used in the workplace which produces fumes, injurious or offensive to any person. Such equipment needs to be regularly maintained. A sufﬁcient number of thermometers should be provided and maintained to enable workers to determine the temperature in any workplace inside a building (but need not be provided in every workroom). Where, despite the provision of local heating or cooling, the temperatures are still unreasonable, suitable protective clothing and rest facilities should be provided.

Physical and psychological health hazards and control Lighting

Workstations and seating

Every workplace shall have suitable and sufﬁcient lighting and this shall be natural lighting so far as is reasonably practicable. Suitable and sufﬁcient emergency lighting must also be provided and maintained in any room where workers are particularly exposed to danger in the event of a failure of artiﬁcial lighting (normally due to a power cut and/or a ﬁre). Windows and skylights should be kept clean and free from obstruction so far as is reasonably practicable unless it would prevent the shading of windows or skylights or prevent excessive heat or glare. When deciding on the suitability of a lighting system, the general lighting requirements will be affected by the following factors:

Workstations should be arranged so that work may be done safely and comfortably. The worker should be at a suitable height relative to the work surface and there should be no need for undue bending and stretching. Workers must not be expected to stand for long periods of time particularly on solid ﬂoors. A suitable seat should be provided when a substantial part of the task can or must be done sitting. The seat should, where possible, provide adequate support for the lower back and a footrest provided for any worker whose feet cannot be placed ﬂat on the ﬂoor. It should be made of materials suitable for the environment, be stable and, possibly, have arm rests. It is also worth noting that sitting for prolonged periods can present health risks, such as blood circulation and pressure problems, vertebral and muscular damage. Seating at work, HSG 57, HSE Books, provides useful guidance on how to ensure that seating in the workplace is safe and suitable.

➤ the availability of natural light ➤ the speciﬁc areas and processes, in particular any colour rendition aspects or concerns over stroboscopic effects (associated with ﬂuorescent lights) ➤ the type of equipment to be used and the need for speciﬁc local lighting ➤ The lighting characteristics required (type of lighting, its colour and intensity) ➤ the location of visual display units and any problems of glare ➤ structural aspects of the workroom and the reduction of shadows ➤ the presence of atmospheric dust ➤ the heating effects of the lighting ➤ lamp and window cleaning and repair (and disposal issues) ➤ the need and required quantity of emergency lighting. Light levels are measured in illuminance, having units of lux (lx), using a light meter. A general guide to lighting levels in different workplaces is given in Table 15.4. Poor lighting levels will increase the risk of accidents such as slips, trips and falls. More information is available on lighting from Lighting at work, HSG 38, HSE Books.

Table 15.4

15.4 Noise There was considerable concern for many years over the increasing cases of occupational deafness and this led to the introduction of Noise at Work Regulations in 1989 and the revised Noise at Work Regulations in 2005. HSE have estimated that an additional 1.1 m workers will be covered by the revised regulations. These regulations which are summarized in Chapter 17, require the employer to: ➤ assess noise levels and keep records ➤ reduce the risks from noise exposure by using engineering controls in the ﬁrst instance and the provision and maintenance of hearing protection as a last resort

Typical workplace lighting levels

Workplace or type of work

Illuminance (lx)

Warehouses and stores

150

General factories or workshops

300

Ofﬁces

500

Drawing ofﬁces (detailed work)

700

Fine working (ceramics or textiles)

1000

Very ﬁne work (watch repairs or engraving)

1400

Figure 15.6 Better to control noise at source rather than wear ear protection.

259

Introduction to Health and Safety at Work ➤ provide employees with information and training ➤ if a manufacturer or supplier of equipment, to provide relevant noise data, on that equipment (particularly if any of the three action levels is likely to be reached). The main purpose of the Noise Regulations is to control noise levels rather than measuring them. This involves the better design of machines, equipment and work processes, ensuring that personal protective equipment is correctly worn and employees are given adequate training and health surveillance. Sound is transmitted through the air by sound waves which are produced by vibrating objects. The vibrations cause a pressure wave which can be detected by a receiver, such as a microphone or the human ear. The ear may detect vibrations which vary from 20 to 20 000 (typically 50–16 000) cycles each second (or Hertz – Hz). Sound travels through air at a ﬁnite speed (342 m/s at 20ºC and sea level). The existence of this speed is shown by the time lag between lightning and thunder during a thunderstorm. Noise normally describes loud, sudden, harsh or irritating sounds. Noise may be transmitted directly through the air, by reﬂection from surrounding walls or buildings or through the structure of a ﬂoor or building. In construction work, the noise and vibrations from a pneumatic drill will be transmitted from the drill itself, the ground being drilled and from the walls of surrounding buildings.

15.4.1

Ill-health effects of noise Noise can lead to ear damage on a temporary (acute) or permanent (chronic) basis. There are three principal acute effects: ➤ temporary threshold shift – caused by short excessive noise exposures and affects the cochlea by reducing the ﬂow of nerve impulses to the brain. The result is a slight deafness, which is reversible when the noise is removed ➤ tinnitus – is a ringing in the ears caused by an intense and sustained high noise level. It is caused by the over-stimulation of the hair cells. The ringing sensation continues for up to 24 hours after the noise has ceased ➤ acute acoustic trauma – caused by a very loud noise such as an explosion. It affects either the eardrum or the bones in the middle ear and is usually reversible. Severe explosive sounds can permanently damage the eardrum. Occupational noise can also lead to one of the following three chronic hearing effects: ➤ noise-induced hearing loss – results from permanent damage to the cochlea hair cells. It affects the ability

Oval Scala window vestibuli

Cochlear duct

Health effects of noise

The human ear

260

Chain of ossicles

Auditory Round tube window

Outer ear

Middle ear

Sound waves in air

Hammer Anvil Stirrup

Scala tympani

Basilar membrane and spiral organ

Inner ear

Oval window

Mechanical movement of ossicles

Perilymph

Endolymph

Perilymph

Fluid wave

Fluid wave stimulates basilar membrane and spiral organ

Fluid wave

Round window

Tympanic (a) membrane

Tympanic membrane

There are three sections of the ear – the outer (or external) ear, the middle ear and the inner (or internal) ear. The sound pressure wave passes into and through the outer ear and strikes the eardrum causing it to vibrate. The eardrum is situated approximately 25 mm inside the head. The vibration of the eardrum causes the proportional movement of three interconnected small bones in the middle ear, thus passing the sound to the cochlea situated in the inner ear. Within the cochlea the sound is transmitted to a ﬂuid causing it to vibrate. The motion of the ﬂuid induces a membrane to vibrate which, in turn, causes hair cells attached to the membrane to bend. The movement of the hair cells causes a minute electrical impulse to be transmitted to the brain along the auditory nerve. Those hairs nearest to the middle ear respond to high frequency, while those at the tip of the cochlea respond to lower frequencies. There are about 30 000 hair cells within the ear and noise-induced hearing loss causes irreversible damage to these hair cells.

(b)

Figure 15.7 Passage of sound waves. (a) The ear with cochlea uncoiled; (b) summary of transmission.

Physical and psychological health hazards and control to hear speech clearly but the ability to hear is not lost completely ➤ permanent threshold shift – this results from prolonged exposure to loud noise and is irreversible due to the permanent reduction in nerve impulses to the brain. This shift is most marked at the 4000 Hz frequency, which can lead to difﬁculty in hearing certain consonants and some female voices; ➤ tinnitus – is the same as the acute form but becomes permanent. It is a very unpleasant condition, which can develop without warning. It is important to note that, if the level of noise exposure remains unchanged, noise-induced hearing loss will lead to a permanent threshold shift affecting an increasing number of frequencies. Presbycusis is the term used for hearing loss in older people which may have been exacerbated by occupational noise earlier in their lives.

Table 15.5 Some typical sound pressure levels (SPL) dB(A) values Activity or environment

SPL (dBA)

Threshold of pain

140

Pneumatic drill

125

Pop group or disco

110

Heavy lorry

93

Street trafﬁc

85

Conversational speech

65

Business ofﬁce

60

Living room

40

Bedroom

25

Threshold of hearing

15.4.2

0

Noise assessments

The Control of Noise at Work Regulations specify action levels at which the hearing of employees must be protected. The conclusion as to whether any of those levels has been breached, is reached after an assessment of noise levels has been made. However, before noise assessment can be discussed, noise measurement and the statutory action levels must be described.

Noise measurement Sound intensity is measured by a unit known as a pascal (Pa – N/m2), which is a unit of pressure similar to that used when inﬂating a tyre. If noise was measured in this way, a large scale of numbers would be required ranging from 1 at one end to 1 million at the other. The sound pressure level (SPL) is a more convenient scale because: ➤ it compresses the size of the scale by using a logarithmic scale to the base 10 ➤ it measures the ratio of the measured pressure, p, to a reference standard pressure, p0, which is the pressure at the threshold of hearing (2 105 Pa). The unit is called a decibel (dB) and is deﬁned as: SPL 20 log10(p/p0) dB It is important to note that since a logarithmic scale to the base 10 is used, each increase of 3 dB is a doubling in the sound intensity. Thus, if a sound reading changes from 75 dB to 81 dB, the sound intensity or loudness has increased by four times. Finally, since the human ear tends to distort its sensitivity to the sound it receives by being less sensitive

to lower frequencies, the scale used by sound meters is weighted so that readings mimic the ear. This scale is known as the A scale and the readings known as dB(A). There are also three other scales known as B, C and D. Finally, since the human ear tends to distort its sensitivity to the sound it receives by being less sensitive to lower frequencies, the scale used by sound meters is weighted so that readings mimic the ear. This scale is known as the A scale and the readings known as dB(A). There are also three other scales known as B, C and D. Originally the A scale was used for sound pressure levels up to 55 dB, the B scale for levels between 55 dB and 85 dB and the C scale for values above 85 dB. However today, the A scale is used for nearly all levels except for very high sound pressure levels when the C scale is used. The B scale is rarely used and the D scale is mainly used to monitor jet aircraft engine noise. Table 15.5 gives some typical dB readings for common activities. Noise is measured using a sound level meter which reads sound pressure levels in dB(A) and the peak sound pressure in pascals (Pa), which is the highest noise level reached by the sound. There are two basic types of sound meter – integrated and direct reading meters. Meters which integrate the reading provide an average over a particular time period which is an essential technique when there are large variations in sound levels. This value is known as the continuous equivalent noise level (LEq) which is normally measured over an 8-hour period. Direct reading devices, which tend to be much cheaper, can be used successfully when the noise levels are continuous at a near constant value.

261

Introduction to Health and Safety at Work Table 15.6

Simple observations to determine the need for a noise risk assessment

Observation at the workplace

Likely noise level

The noise is noticeable but does not interfere with normal conversation – equivalent to a domestic vacuum cleaner

80 dB(A)

6 hours

People have to shout to be heard if they are more than 2 m apart

85 dB(A)

2 hours

People have to shout to be heard if they are more than 1 m apart

90 dB(A)

45 minutes

Another important noise measurement is the daily personal exposure level of the worker, LEP,d, which is measured over an 8-hour working day. Hence, if a person was exposed to 87 dB(A) over 4 hours, this would equate to a LEP,d of 84 dB(A) since a reduction of 3 dB(A) represents one half of the noise dose. The HSE Guidance on the Control of Noise at Work Regulations, L108, offers some very useful advice on the implementation of the Regulations and should be read by anyone who suspects that they have a noise problem at work. The guidance covers ‘equipment and procedures for noise surveys’ and contains a noise exposure readyreckoner which can be used to evaluate LEP,d when the noise occurs during several short intervals and/or at several different levels during the 8-hour period.

Noise action levels Regulation 6, of the Control of Noise at Work Regulations places a duty on employers to reduce the risk of damage to the hearing of their employees from exposure to noise to the lowest level reasonably practicable. The regulations introduce exposure action level values and exposure limit values. An exposure action value is a level of noise at which certain action must be taken. An exposure limit value is a level of noise at the ear above which an employee must not be exposed. Therefore if the workplace noise levels are above this value, any ear protection provided to the employee must reduce the noise level to the limit value at the ear. These exposure action and limit values are: 1.

2.

The lower exposure action levels are: (a) a daily or weekly personal noise exposure of 80 dB(A); and (b) a peak sound pressure of 135 dB(C) The upper exposure action levels are: (a) a daily or weekly personal noise exposure of 85 dB(A); and (b) a peak sound pressure of 137 dB(C)

262

3.

A noise risk assessment must be made if this noise level persists for

The exposure limit values are: (a) a daily or weekly personal noise exposure of 87 dB(A); and (b) a peak sound pressure of 140 dB(C).

The peak exposure action and limit values are deﬁned because high level peak noise can lead to short-term and long-term hearing loss. Explosives, guns (including nail guns), cartridge tools, hammers and stone chisels can all produce high peak sound pressures. If the daily noise exposure exceeds the lower exposure action level, then a noise assessment should be carried out and recorded by a competent person. There is a very simple test which can be done in any workplace to determine the need for an assessment. Table 15.6 gives information on the simple test to determine the need for a noise risk assessment. If there is a marked variation in noise exposure levels during the working week, then the regulations allow a weekly rather than daily personal exposure level, (LEP,w), to be used. It is only likely to be signiﬁcantly different to the daily exposure level if exposure on one or two days in the working week is 5 dB(A) higher than on the other days, or the working week has three or fewer days of exposure. The weekly exposure rate is not a simple arithmetic average of the daily rates. If an organization is considering the use of a weekly exposure level, then the following provisions must be made: ➤ hearing protection must be provided if there are very high noise levels on any one day ➤ the employees and their representatives must be consulted on whether weekly averaging is appropriate ➤ an explanation must be given to the employees on the purpose and possible effects of weekly averaging. Finally, if the working day is 12 hours, then the action levels must be reduced by 3 dB(A) because the action levels assume an 8-hour working day.

Physical and psychological health hazards and control The HSE Guidance document L108 gives detailed advice on noise assessments and surveys. The most important points are that the measurements should be taken at the working stations of the employees closest to the source of the noise and over as long a period as possible, particularly if there is a variation in noise levels during the working day. Other points to be included in a noise assessment are: ➤ details of the noise meter used and the date of its last calibration ➤ the number of employees using the machine, time period of usage and other work activities ➤ an indication of the condition of the machine and its maintenance schedule ➤ the work being done on the machine at the time of the assessment ➤ a schematic plan of the workplace showing the position of the machine being assessed ➤ other noise sources, such as ventilation systems, should be considered in the assessment. The control of these sources may help to reduce overall noise levels ➤ recommendations for future actions, if any. Other actions which the employer must undertake when the lower exposure action level is exceeded are: ➤ inform, instruct and train employees on the hearing risks ➤ supply hearing protection to those employees requesting it ➤ ensure that any equipment or arrangements provided under the regulations are correctly used or implemented. The additional measures which the employer must take if the upper exposure action level is reached are: ➤ reduce and control exposure to noise by means other than hearing protection ➤ establish hearing protection zones, marked by notices and ensure that anybody entering the zone is wearing hearing protection ➤ supply hearing protection and ensure that it is worn. The Control of Noise at Work Regulations place a duty on the employer to undertake health surveillance for employees whose exposure regularly exceeds the upper action level irrespective of whether ear protection was worn. The recommended health surveillance is a hearing test at induction, followed by an annual check and review of hearing levels. The checks may be extended to every three years if no adverse effects are found during earl-ier tests. If exposure continues over a long period,

Ear protection zone Ear protectors must be worn in this area Figure 15.8

Typical ear protection zone sign.

health surveillance of employees is recommended using a more substantial audiometric test. This will indicate whether there has been any deterioration in hearing ability. Where exposure is between the lower and upper exposure action levels or occasionally above the upper action values, health surveillance will only be required if information becomes available, perhaps from medical records, that the employee is particularly sensitive to noise-induced hearing loss. The Regulations also place the following statutory duties on employees: ➤ for noise levels above the lower exposure action level, they must use any control; equipment (other than hearing protection), such as silencers, supplied by the employer and report any defects ➤ for noise levels above the upper exposure action level, they fulﬁl the obligations given above and wear the hearing protection provided ➤ they must take care of any equipment provided under these regulations and report any defects ➤ they must see their doctor if they feel that their hearing has become damaged. The Management of Health and Safety Regulations prohibits the employment of anyone under the age of 18 years where there is a risk to health from noise.

15.4.3

Noise control techniques

In addition to reduced time exposure of employees to the noise source, there is a simple hierarchy of control techniques: ➤ reduction of noise at source ➤ reduction of noise levels received by the employee (known as attenuation) ➤ personal protective equipment, which should only be used when the above two remedies are insufﬁcient.

263

Introduction to Health and Safety at Work

Figure 15.9

Segregation of a noisy operation to benefit the whole workplace.

Reduction of noise at source

➤ change the process or equipment (e.g. replace solid tyres with rubber tyres or replace diesel engines with electric motors) ➤ change the speed of the machine ➤ improve the maintenance regime by regular lubrication of bearings, tightening of belt drives.

Lagging – the insulation of pipes and other ﬂuid containers to reduce sound transmission (and, incidentally, heat loss). Silencers – normally ﬁtted to engines which are exhausting gases to atmosphere. Silencers consist of absorbent material or bafﬂes. Isolation of the workers – the provision of soundproofed workrooms or enclosures isolated away from noisy equipment (a power station control room is an example of worker isolation).

Attenuation of noise levels

15.4.4

There are several means by which noise could be reduced at source:

There are many methods of attenuating or reducing noise levels and these are covered in detail in the guide to the Regulations. The more common ones will be summarized here. Orientation or re-location of the equipment – turn the noisy equipment away from the workforce or locate it away in separate and isolated areas. Enclosure – surrounding the equipment with a good sound insulating material can reduce sound levels by up to 30 dB(A). Care will need to be taken to ensure that the machine does not become overheated. Screens or absorption walls – can be used effectively in areas where the sound is reﬂected from walls. The walls of the rooms housing the noisy equipment are lined with sound absorbent material, such as foam or mineral wool, or sound absorbent (acoustic) screens are placed around the equipment. Damping – the use of insulating ﬂoor mountings to remove or reduce the transmission of noise and vibrations through the structure of the building such as girders, wall panels and ﬂooring.

264

Personal ear protection

The provision of personal hearing protection should only be considered as a last resort. There is usually resistance from the workforce to use them and they are costly to maintain and replace. They interfere with communications, particularly alarm systems, and they can present hygiene problems. The following factors should be considered when selecting personal ear protection: ➤ suitability for the range of sound spectrum of frequencies to be encountered ➤ noise reduction (attenuation) offered by the ear protection ➤ pattern of the noise exposure ➤ acceptability and comfort of the wearer, particularly if there are medical problems ➤ durability ➤ hygiene considerations ➤ compatibility with other personal protective equipment ➤ ease of communication and able to hear warning alarms

Physical and psychological health hazards and control ➤ maintenance and storage arrangements ➤ cost. There are two main types of ear protection – earplugs and ear defenders (earmuffs). Earplugs are made of sound absorbent material and ﬁt into the ear. They can be reusable or disposable, are able to ﬁt most people and can easily be used with safety glasses and other personal protective equipment. Their effectiveness depends on the quality of the ﬁt in the ear which, in turn, depends on the level of training given to the wearer. Permanent earplugs come in a range of sizes so that a good ﬁt is obtained. The effectiveness of earplugs decreases with age and should be replaced at the intervals speciﬁed by the supplier. A useful simple rule to ensure that the selected ear plug reduces the noise level at the ear to 87 dB(A) is to choose one with a manufacturers rating of 83 dB(A). This should compensate for any ﬁtting problems. The main disadvantage of ear plugs is that they do not reduce the sound transmitted through the bone structure which surrounds the ear and they often work loose with time. Ear defenders (earmuffs) offer a far better reduction of all sound frequencies. They are generally more acceptable to workers because they are more comfortable to wear and they are easy to monitor since they are clearly visible. They also reduce the sound intensity transmitted through the bone structure surrounding the ear. A communication system can be built into earmuffs. However, they may be less effective if the user has long hair or is wearing spectacles or large ear rings. They may also be less effective if worn with helmets or face shields and uncomfortable in warm conditions. Maintenance is an important factor with earmuffs and should include checks for wear and tear and general cleanliness. Selection of suitable ear protection is very important since they should not just reduce sound intensities below the statutory action levels but also reduce those intensities at particular frequencies. Normally advice should be sought from a competent supplier who will be able to advise ear protection to suit a given spectrum of noise using ‘octave band analysis’. Finally, it is important to stress that the use of ear protection must be well supervised to ensure that, not only is it being worn correctly, but that it is, in fact, actually being worn.

energy and the build-up of fat reserves, but also generates heat which needs to be dissipated to the surrounding environment. The body also receives heat from its surroundings. The body temperature is normally around 37ºC and will attempt to maintain this temperature irrespective of the temperature of the surroundings. Therefore, if the surroundings are hot, sweating will allow heat loss to take place by evaporation caused by air movement over the skin. On the other hand, if the surroundings are cold, shivering causes internal muscular activity, which generates body heat. At high temperatures, the body has more and more difﬁculty in maintaining its natural temperature unless sweating can take place and therefore water must be replaced by drinking. If the surrounding air has high humidity, evaporation of the sweat cannot take place and the body begins to overheat. This leads to heart strain and, in extreme cases, heat stroke. It follows that when working is required at high temperatures, a good supply of drinking water should be available and, further, if the humidity is high, a good supply of ventilation air is also needed. Heat exhaustion is a particular hazard in conﬁned spaces. At low temperatures, the body will lose heat too rapidly and the extremities of the body will become very cold leading to frostbite and possibly the loss of

The Heat Equation HIGH TEMPERATURE + HIGH HUMIDITY + PHYSICAL WORK = HEAT ILLNESS When the body is unable to cool itself through sweating, serious heat illnesses may occur. The most severe heat induced illnesses are heat exhaustion and heat stroke. If left untreated, heat exhaustion could progress to heat stroke and possible death.

15.5 Heat and radiation hazards

Relative humidity

Temperature

70%

100 F 37.8 C

60%

95 F 37 C

50%

90 F 32.2 C

40%

85 F 29.4 C

30%

80 F 26.7 C

Danger Caution

15.5.1

Extremes of temperature

The human body is very sensitive to relatively small changes in external temperatures. Food not only provides

Less hazardous

Figure 15.10

The heat equation.

265

Introduction to Health and Safety at Work limbs. Under these conditions, thick warm clothing and external heating will be required. In summary, extremes of temperature require special measures, particularly if accompanied by extremes of humidity. Frequent rest periods will be necessary to allow the body to acclimatize to the conditions. An index called WBGT (Wet Bulb Globe Temperature) is normally used.

15.5.2

Ionising radiation

Ionising radiation is emitted from radioactive materials, either in the form of directly ionising alpha and beta particles or indirectly ionising X- and gamma rays or neutrons. It has a high energy potential and an ability to penetrate, ionise and damage body tissue and organs. All matter consists of atoms within which is a nucleus, containing protons and neutrons, and orbiting electrons. The number of electrons within the atom deﬁnes the element – hydrogen has 1 electron and lead has 82 electrons. Some atoms are unstable and will change into atoms of another element, emitting ionising radiation in the process. The change is called radioactive decay and the ionising radiations most commonly emitted are alpha and beta particles and gamma rays. X-rays are produced by bombarding a metal target with electrons at very high speeds using very high voltage electrical discharge equipment. Neutrons are released by nuclear ﬁssion and are not normally found in manufacturing processes. Alpha particles consist of two protons and two neutrons and have a positive charge. They have little power to penetrate the skin and can be stopped using very ﬂimsy material, such as paper. Their main route into the body is by ingestion. Beta particles are high speed electrons whose power of penetration depends on their speed, but penetration is usually restricted to 2 cm of skin and tissue. They can be stopped using aluminium foil. There are normally two routes of entry into the body – inhalation and ingestion. Gamma rays, which are similar to X-rays, are electromagnetic radiations and have far greater penetrating power than alpha or beta particles. They are produced from nuclear reactions and can pass through the body.

There are two principal units of radiation – the becquerel (1 Bq) which measures the amount of radiation in a given environment and the millisievert (1 mSv) which measures the ionising radiation dose received by a person. Ionising radiation occurs naturally as well as from man-made processes and about 87% of all radiation exposure is from natural sources. The Ionising Radiations Regulations specify a range of dose limits, some of which are given in Table 15.7.

Harmful effects of ionising radiation Ionising radiation attacks the cells of the body by producing chemical changes in the cell DNA by ionising it (thus producing free radicals) which leads to abnormal cell growth. The effects of these ionising attacks depend on the following factors: ➤ the size of the dose – the higher the dose then the more serious will be the effect ➤ the area or extent of the exposure of the body – the effects may be far less severe if only a part of the body (e.g. an arm) receives the dose ➤ the duration of the exposure – a long exposure to a low dose is likely to be less harmful than a short exposure to the same quantity of radiation. Acute exposure can cause, dependent on the size of the dose, blood cell changes, nausea and vomiting, skin burns and blistering, collapse and death. Chronic exposure can lead to anaemia, leukaemia and other forms of cancer. It is also known that ionising radiation can have an adverse effect on the function of human reproductive organs and processes. Increases in the cases of sterility, stillbirths and malformed foetuses have also been observed.

Table 15.7

Typical radiation dose limits Dose (mSv)

Area of body

20

Whole body per year

Trainees 16–18 years

6

Whole body per year

Any other person

1

Whole body per year

Employees aged 18 years

Figure 15.11

266

Typical ionising sign.

Women employees of child-bearing age

13

Pregnant employees

1

The abdomen in any consecutive 3-month period During the declared term of the pregnancy

Physical and psychological health hazards and control The health effects of ionising radiation may be summarized into two groups – somatic effects which refers to cell damage in the person exposed to the radiation dose and genetic effects which refers to the damage done to the children of the irradiated person.

Sources of ionising radiation The principal workplaces which could have ionising radiation present are the nuclear industry, medical centres (hospitals and research centres) and educational centres. Radioactive processes are used for the treatment of cancers and radioactive isotopes are used for many different types of scientiﬁc research. X-rays are used extensively in hospitals, but they are also used in industry for nondestructive testing (e.g. crack detection in welds). Smoke detectors, used in most workplaces, also use ionising radiations. Ionising radiations can also occur naturally – the best example being radon, which is a radioactive gas that occurs mainly at or near granite outcrops where there is a presence of uranium. It is particularly prevalent in Devon and Cornwall. The gas enters buildings normally from the substructure through cracks in ﬂooring or around service inlets. The Ionising Regulations have set two action levels above which remedial action, such as sumps and extraction fans, have to be ﬁtted to lower the radon level in the building. The ﬁrst action level is 400 Bq/m3 in workplaces and 200 Bq/m3 in domestic properties. At levels above 1000 Bq/m3, remedial action should be taken within one year. Personal radiation exposure can be measured using a ﬁlm badge, which is worn by the employee over a ﬁxed time interval. The badge contains a photographic ﬁlm which, after the time interval, is developed and an estimate of radiation exposure is made. A similar device, known as a radiation dose meter or detector, can be positioned on a shelf in the workplace for three months, so that a mean value of radiation levels may be measured. Instantaneous radiation values can be obtained from portable hand-held instruments, known as geiger counters, which continuously sample the air for radiation levels. Similar devices are available to measure radon levels.

15.5.3

Non-ionising radiation

Non-ionising radiation includes ultraviolet, visible light (this includes lasers which focus or concentrate visible light), infrared and microwave radiations. Since the wavelength is relatively long, the energy present is too low to ionise atoms which make up matter. The action of non-ionising radiation is to heat cells rather than change their chemical composition. Other than the Health and Safety at Work Act there is no speciﬁc set of regulations governing non-ionising

radiation. However, the Personal Protective Equipment at Work Regulations are particularly relevant since the greatest hazard is tissue burning of the skin or the eyes. Ultraviolet radiation occurs with sunlight and with electric arc welding. In both cases, the skin and the eyes are at risk from the effect of burning. The skin will burn (as in sunburn) and repeated exposure can lead to skin cancer. Skin which is exposed to strong sun light, should be protected either by clothing or barrier creams. This problem has become more common with the reduction in the ozone layer (which ﬁlters out much ultraviolet light). The eyes can be affected by a form of conjunctivitis which feels like grit in the eye, and is called by a variety of names dependent on the activity causing the problem. Arc welders call it ‘arc eye’ or ‘welder’s eye’ and skiers ‘snow blindness’. Cataracts caused by the action of ultraviolet radiation on the eye lens is another possible outcome of exposure. With growing concern following the rise in skin cancers, the HSE has suggested the following hierarchy of controls for outdoor working: ➤ Relocate some jobs inside a building or to a shady location ➤ Undertake some outdoor work earlier or later in the day ➤ Provide personal protection (hats and/or sun cream) ➤ Provide suitable education and training to outdoor workers. Lasers use visible light and light from the invisible wavelength spectrum (infra-red and ultraviolet). As the word laser implies, they produce ‘light ampliﬁcation by stimulated emission of radiation’. This light is highly concentrated and does not diverge or weaken with distance and the output is directly related to the chemical composition of the medium used within the particular laser. The output beam may be pulsating or continuous – the choice being dependent on the task of the laser. Lasers have a large range of applications including bar code reading at a supermarket checkout, the cutting and welding of metals and accurate measurement of distances and elevations required in land and mine surveying. They are also extensively used in surgery for cataract treatment and the sealing of blood vessels. Lasers are classiﬁed into ﬁve classes (1, 2, 3a, 3b and 4) in ascending size of power output. Classes 1 and 2 are relatively low hazard and only emit light in the visible band. Classes 3a, 3b and 4 are more hazardous and the appointment of a laser safety ofﬁcer is recommended. All lasers should carry information stating their class and any precautions required during use. The main hazards associated with lasers are eye and skin burns, toxic fumes, electricity and ﬁre. The vast majority of accidents with lasers affect the eyes. Retinal

267

Introduction to Health and Safety at Work damage is the most common and is irreversible. Cataract development and various forms of conjunctivitis can also result from laser accidents. Skin burning and reddening (erythema) are less common and are reversible. Infra-red radiation is generated by ﬁres and hot substances and can cause eye and skin damage similar to that produced by ultraviolet radiation. It is a particular problem to ﬁre ﬁghters and those who work in foundries or near furnaces. Eye and skin protection are essential. Microwaves are used extensively in cookers and mobile telephones and there are ongoing concerns about associated health hazards (and several inquiries are currently under way). The severity of any hazard is proportional to the power of the microwaves. The principal hazard is the heating of body cells, particularly those with little or no blood supply to dissipate the heat. This means that tissues such as the eye lens are most at risk from injury. However, it must be stressed that any risks are higher for items, such as cookers, than for lowpowered devices, such as mobile phones. The measurement of non-ionising radiation normally involves the determination of the power output being received by the worker. Such surveys are best performed by specialists in the ﬁeld, since the interpretation of the survey results requires considerable technical knowledge.

➤ procedures to deal with spillages and other accidents ➤ prominent signs and information regarding the radiation hazards ➤ medical surveillance of employees. The Ionising Radiations Regulations specify a range of precautions which must be taken, including the appointment of a Radiation Protection Supervisor and a Radiation Protection Adviser. The Radiation Protection Supervisor must be appointed by the employer to advise on the necessary measures for compliance with the Regulations and its Approved Code of Practice. The person appointed, who is normally an employee, must be competent to supervise the arrangements in place and have received relevant training. The Radiation Protection Adviser is appointed by the employer to give advice to the Radiation Protection Supervisor and employer on any aspect of working with ionising radiation including the appointment of the Radiation Protection Supervisor. The Radiation Protection Adviser is often an employee of a national organization with expertise in ionising radiation.

Non-ionising radiation 15.5.4

Radiation protection strategies

Ionising radiation Protection is obtained by the application of shielding, time and distance either individually or, more commonly, a mixture of all three. Shielding is the best method because it is an ‘engineered’ solution. It involves the placing of a physical shield, such as a layer of lead, steel and concrete, between the worker and the radioactive source. The thicker the shield the more effective it is. Time involves the use of the reduced time exposure principle and thus reduces the accumulated dose. Distance works on the principle that the effect of radiation reduces as the distance between the worker and the source increases. Other measures include the following: ➤ effective emergency arrangements ➤ training of employees ➤ the prohibition of eating, drinking and smoking adjacent to exposed areas ➤ a high standard of personal cleanliness and ﬁrst-aid arrangements ➤ strict adherence to personal protective equipment arrangements, which may include full body protection and respiratory protection equipment

268

For ultraviolet and infra-red radiation, eye protection in the form of goggles or a visor is most important, particularly when undertaking arc welding or furnace work. Skin protection is also likely to be necessary for the hands, arms and neck in the form of gloves, sleeves and a collar. For construction and other outdoor workers, protection from sunlight is important, particularly for the head and nose. Barrier creams should also be used. For laser operations, engineering controls such as ﬁxed shielding and the use of non-reﬂecting surfaces around the workstation are recommended. For laser in the higher class numbers, special eye protection is recommended. A risk assessment should be undertaken before a laser is used. Engineering controls are primarily used for protection against microwaves. Typical controls include the enclosure of the whole microwave system in a metal surround and the use of an interlocking device that will not allow the system to operate unless the door is closed. The non-ionising radiation hazards caused by arc welding are not the only hazards associated with welding operations. The hazards from fume inhalation, trailing cables and pipes and the manual handling of cylinders are also present. There have also been serious injuries resulting from explosions and ﬁres during welding processes. Many of these accidents occur on farms where welding equipment is used to make on-the-spot repairs to agricultural machinery.

Physical and psychological health hazards and control 15.6 The causes and prevention of workplace stress In 2001, the HSE estimated that stress in the workplace cost approximately 6.7 million days lost each year and society between £3.7 billion and £3.8 billion. This has been accompanied by an increase in civil claims resulting from stress at work. Stress is not a disease – it is the natural reaction to excessive pressure. Stress can lead to an improved performance, but is not a good thing, since it is likely to lead to both physical and mental ill-health, such as high blood pressure, peptic ulcers, skin disorders and depression. Most people experience stress at some time during their lives, during an illness or death of a close relative or friend. However, recovery normally occurs after the particular crisis has passed. The position is, however, often different in the workplace because the underlying causes of the stress, known as work-related stressors, are not relieved but continue to build up the stress levels until the employee can no longer cope. The basic workplace stressors are: ➤ the job itself – boring or repetitive, unrealistic performance targets or insufﬁcient training, job insecurity or fear of redundancy ➤ individual responsibility – ill-deﬁned roles and too much responsibility with too little power to inﬂuence the job outputs ➤ working conditions – cramped, dirty and untidy workplace; unsafe practices; lack of privacy or security; inadequate welfare facilities; threat of violence; excessive noise, vibration or heat; poor lighting; lack of ﬂexibility in working hours to meet domestic requirements and adverse weather conditions for those working outside ➤ management attitudes – poor communication, consultation or supervision, negative health and safety culture, lack of support in a crisis ➤ relationships – unhappy relationship between workers, bullying, sexual and racial harassment. Possible solutions to all these stressors have been addressed throughout this book and involve the creation of a positive health and safety culture, effective training and consultation procedures and a set of health and safety arrangements which work on a day-to-day basis. The HSE have produced its own generic stress audit survey tool which is available free of charge on its website and advises the following action plan: ➤ identify the problem ➤ identify the background to the problem and how it was discovered

➤ identify the remedial action required and give reasons for that action ➤ identify targets and reasonable target dates, and ➤ agree a review date with employees to check that the remedial action is working. The following additional measures have also been found to be effective by some employers: ➤ take a positive attitude to stress issues by becoming familiar with its causes and controls ➤ take employees’ concerns seriously and develop a counselling system which will allow a frank, honest and conﬁdential discussion of stress-related problems ➤ develop an effective system of communication and consultation and ensure that periods of uncertainty are kept to a minimum ➤ set out a simple policy on work-related stress and include stressors in risk assessments ➤ ensure that employees are given adequate and relevant training and realistic performance targets ➤ develop an effective employee appraisal system which includes mutually agreed objectives ➤ discourage employees from working excessive hours and/or missing break periods (this may involve a detailed job evaluation) ➤ introduce job rotation and increase job variety ➤ develop clear job descriptions and ensure that the individual is matched to them ➤ encourage employees to improve their lifestyle (e.g. many local health authorities provide smoking cessation advice sessions) ➤ monitor incidents of bullying, sexual and racial harassment and, where necessary, take disciplinary action ➤ train supervisors to recognise stress symptoms among the workforce ➤ avoid a blame culture over accidents and incidents of ill-health. The individual can also take action if he feels that he is becoming over-stressed. Regular exercise, change of job, review of diet and talking to somebody, preferably a trained counsellor, are all possibilities. Workplace stress has no speciﬁc health and safety regulations but is covered by the duties imposed by the Health and Safety at Work Act and the Management of Health and Safety at Work Regulations 1999 to: ➤ ensure so far as is reasonably practicable that workplaces are safe and without risk to health ➤ carry out a risk assessment relating to the risks to health ➤ introduce and maintain appropriate control measures. There have been several successful civil actions for compensatory claims resulting from the effects of workplace

269

Introduction to Health and Safety at Work stress. However, the Court of Appeal in 2002 redeﬁned the guidelines under which workplace stress compensation claims may be made. Their full guidelines should be consulted and consist of sixteen points. In summary, these guidelines are as follows: ➤ no occupations should be regarded as intrinsically dangerous to mental health ➤ it is reasonable for the employer to assume that the employee can withstand the normal pressures of the job, unless some particular problem or vulnerability has developed ➤ the employer is only in breach of duty if they have failed to take the steps that are reasonable in the circumstances ➤ the size and scope of the employer’s operation, its resources and the demands it faces are relevant in deciding what is reasonable; including the interests of other employees and the need to treat them fairly in, for example, the redistribution of duties ➤ if a conﬁdential counselling advice service is offered to the employee, the employer is unlikely to be found in breach of his duty ➤ if the only reasonable and effective action is to dismiss or demote the employee, the employer is not in breach of his duty by allowing a willing worker to continue in the same job ➤ the assessment of damages will take account of any pre-existing disorder or vulnerability and the chance that the claimant would have succumbed to a stress-related disorder in any event. Stress usually occurs when people feel that they are losing control of a situation. In the workplace, this means that the individual no longer feels that they can cope with the demands made on them. Many such problems can be partly solved by listening to rather than talking at people.

15.7 Causes and prevention of workplace violence Violence at work, particularly from dissatisﬁed customers, clients, claimants or patients, causes a lot of stress and in some cases injury. This is not only physical violence as people may face verbal and mental abuse, discrimination, harassment and bullying. Fortunately, physical violence is still rare, but violence of all types has risen signiﬁcantly in recent years. Violence at work is known to cause pain, suffering, anxiety and stress, leading to ﬁnancial costs due to absenteeism and higher insurance premiums to cover increased civil claims. It can be very costly to ignore the problem.

270

Figure 15.12 Security coded access and surveillance CCTV camera.

In 1999 the Home Ofﬁce and the Health and Safety Executive published a comprehensive report entitled Violence at Work: Findings from the British Crime Survey. This was updated with a joint report Violence at Work: New Findings of The British Crime Survey 2000, which was published in July 2001. This report shows the extent of violence at work and how it has changed during the period 1991–1999 (Table 15.8).

Table 15.8 Trend in physical assaults and threats at work, 1991–1999 (based on working adults of working age)

Number of incidents (000s)

1991

1993

1995

1997

1999

All violence

947

1275

1507

1226

1288

Assaults

451

652

729

523

634

Threats

495

607

779

703

654

All violence

472

530

570

649

604

Assaults

227

287

290

275

304

Threats

264

286

352

395

338

Number of victims (000s)

Source: British Crime Survey 1999

Physical and psychological health hazards and control The report deﬁnes violence at work as: All assaults or threats which occurred while the victim was working and were perpetuated by members of the public. Physical assaults include the offences of common assault, wounding, robbery and snatch theft. Threats include both verbal threats, made to or against the victim and non-verbal intimidation. These are mainly threats to assault the victim and, in some cases, to damage property. Excluded from the survey are violent incidents where there was a relationship between the victim and the offender and also where the offender was a work colleague. The latter category was excluded because of the different nature of such incidents. The British Crime Survey shows that the number of incidents and victims rose rapidly between 1991 and 1995 but then declined to 1997. Unfortunately, since 1997 the decline seems to have reversed as the number of incidents has increased by 5%. It is interesting that almost half of the assaults and a third of the threats happened after 1800 hrs which suggests that the risks are higher if people work at night or in the late evening. Sixteen per cent of the assaults involved offenders under the age of 16 and were mainly against teachers or other education workers. Violence at work is deﬁned by the HSE as: any incident in which an employee is abused, threatened or assaulted in circumstances relating to their work. In recognition of this, the HSE has produced a useful guide to employers which includes a four stage action plan and some advice on precautionary measures (Violence at Work a guide for employers, INDG69 (rev)). The employer is just as responsible, under health and safety legislation, for protecting employees from violence as they are for any other aspects of their safety. The Health and Safety at Work Act puts broad general duties on employers and others to protect the health and safety of staff. In particular, section 2 of the HSW Act gives employers a duty to safeguard, so far as is reasonably practicable, the health, safety and welfare at work of their staff. Employers also have a common law general duty of care towards their staff, which extends to the risk of violence at work. Legal precedents (see West Bromwich Building Society v Townsend [1983] IRLR 147 and Charlton v Forrest Printing Ink Company Limited [1980] IRLR 331) show that employers have a duty to take reasonable care to see that their staff are not exposed to unnecessary risks at work, including the risk of injury by criminals. In carrying out their duty to provide a safe system of work and a safe working place, employers should, therefore, have regard to,

and safeguard their staff against, the risk of injury from violent criminals. The HSE recommend the following four-point action plan: 1. 2. 3. 4.

ﬁnd out if there is a problem decide on what action to take take the appropriate action check that the action is effective.

15.7.1

Find out if there is a problem

This involves a risk assessment to determine what the real hazards are. It is essential to ask people at the workplace and, in some cases, a short questionnaire may be useful. Record all incidents to get a picture of what is happening over time, making sure that all relevant detail is recorded. The records should include: ➤ a description of what happened ➤ details of who was attacked, the attacker and any witnesses ➤ the outcome, including how people were affected and how much time was lost ➤ information on the location of the event. Due to the sensitive nature of some aggressive or violent actions, employees may need to be encouraged to report incidents and be protected from future aggression. All incidents should be classiﬁed so that an analysis of the trends can be examined. Consider the following: ➤ fatalities ➤ major injury ➤ less severe injury or shock which requires ﬁrst-aid treatment, outpatient treatment, time off work or expert counseling ➤ threat or feeling of being at risk or in a worried or distressed state.

15.7.2

Decide on what action to take

It is important to evaluate the risks and decide who may be harmed and how this is likely to occur. The threats may be from the public or co-workers at the workplace or it may be as a result of visiting the homes of customers. Consultation with employees or other people at risk will improve their commitment to control measures and will make the precautions much more effective. The level of training and information provided, together with the general working environment and the design of the job, all have a signiﬁcant inﬂuence on the level of risk. Those people at risk could include those working in: ➤ reception or customer service points ➤ enforcement and inspection

271

Introduction to Health and Safety at Work ➤ lone working situations and community based activities ➤ front line service delivery ➤ education and welfare ➤ catering and hospitality ➤ retail petrol and late night shopping operations ➤ leisure facilities, especially if alcohol is sold ➤ healthcare and voluntary roles ➤ policing and security ➤ mental health units or in contact with disturbed people ➤ cash handling or control of high value goods. Consider the following issues: ➤ ➤ ➤ ➤

quality of service provided design of the operating environment type of equipment used designing the job.

Some violence may be deterred if measures are taken which suggest that any violence may be recorded. Many public bodies use the following measures: ➤ informing telephone callers that their calls will be recorded ➤ displaying prominent notices that violent behaviour may lead to the withdrawal of services and prosecution ➤ using CCTV or security personnel.

Quality of service provided The type and quality of service provision has a signiﬁcant effect on the likelihood of violence occurring in the workplace. Frustrated people whose expectations have not been met and who are treated in an unprofessional way may believe they have the justiﬁcation to cause trouble. Sometimes circumstances are beyond the control of the staff member and potentially violent situations need to be defused. The use of correct skills can turn a dissatisﬁed customer into a conﬁrmed supporter simply by careful response to their concerns. The perceived lack of or incorrect information can cause signiﬁcant frustrations.

Design of the operating environment Personal safety and service delivery are very closely connected and have been widely researched in recent years. This has resulted in many organizations altering their facilities to reduce customer frustration and enhance sales. It is interesting that most service points experience less violence when they remove barriers or screens, but the transition needs to be carefully planned in consultation with staff and other measures adopted to reduce the risks and improve their protection.

272

The layout, ambience, colours, lighting, type of background music, furnishings including their comfort, information, things to do while waiting and even smell all have a major impact. Queue jumping causes a lot of anger and frustration and needs effective signs and proper queue management, which can help to reduce the potential for conﬂict. Wider desks, raised ﬂoors and access for special needs, escape arrangements for staff, carefully arranged furniture and screening for staff areas can all be utilized.

Type of security equipment used There is a large amount of equipment available and expert advice is necessary to ensure that it is suitable and sufﬁcient for the task. Some measures that could be considered include the following: ➤ Access control to protect people and property. There are many variations from staffed and friendly receptions, barriers with swipe-cards and simple coded security locks. The building layout and design may well partly dictate what is chosen. People inside the premises need access passes so they can be identiﬁed easily. ➤ Closed circuit television is one of the most effective security arrangements to deter crime and violence. Because of the high cost of the equipment, it is essential to ensure that proper independent advice is obtained on the type and the extent of the system required. ➤ Alarms – there are three main types: ➤ Intruder alarms ﬁtted in buildings to protect against unlawful entry, particularly after hours ➤ Panic alarms used in areas such as receptions and interview rooms covertly located so that they can be operated by the staff member threatened ➤ Personal alarms carried by an individual to attract attention and to temporarily distract the attacker ➤ Radios and pagers can be a great asset to lone workers in particular, but special training is necessary as good radio discipline with a special language and codes are required ➤ Mobile phones are an effective means of communicating and keeping colleagues informed of people’s movements and problems such as travel delays. Key numbers should be inserted for rapid use in an emergency.

Job design Many things can be done to improve the way in which the job is carried out to improve security and avoid violence. These include: ➤ using cashless payment methods ➤ keeping money on the premises to a minimum ➤ careful check of customer or client’s credentials

Physical and psychological health hazards and control ➤ careful planning of meetings away from the workplace ➤ team work where suspected aggressors may be involved ➤ regular contact with workers away from their base. There are special services available to provide contact arrangements ➤ avoidance of lone working as far as is reasonably practicable ➤ thinking about how staff who have to work shifts or late hours will get home. Safe transport and/or parking areas may be required ➤ setting up support services to help victims of violence and, if necessary, other staff who could be affected. They may need debrieﬁng, legal assistance, time off work to recover or counselling by experts.

15.7.3

Take the appropriate action

The arrangements for dealing with violence should be included in the safety policy and managed like any other aspect of the health and safety procedures. Action plans should be drawn up and followed through using the consultation arrangements as appropriate. The police should also be consulted to ensure that they are happy with the plan and are prepared to play their part in providing back up and the like.

15.7.4

Check that the action is effective

Ensure that the records are being maintained and any reported incidents are investigated and suitable action taken. The procedures should be regularly audited and changes made if they are not working properly. Victims should be provided with help and assistance to overcome their distress, through debrieﬁng, counselling, time off to recover, legal advice and support from colleagues.

15.8 The effects of alcohol and drugs Alcohol and drug abuse damages health and causes absenteeism and reduced productivity. The HSE is keen to see employers address the problem and offers advice in two separate booklets. Alcohol abuse is a considerable problem when vehicle driving is part of the job especially if driving is required on public roads. Misuse of alcohol can reduce productivity, increase absenteeism, increase accidents at work and, in some cases, endanger the public. Employers need to adopt an alcohol policy following employee consultation. The following matters need to be considered: ➤ how the organization expects employees to restrict their level of drinking

➤ how problem drinking can be recognized and help offered and ➤ at what point and under what circumstances will an employee’s drinking be treated as a disciplinary rather than a health problem. Prevention of the problem is better than remedial action after a problem has occurred. During working hours, there should be no drinking and drinking during break periods should be discouraged. Induction training should stress this policy and managers should set them. Posters can also help to communicate the message. However, it is important to recognize possible symptoms of an alcohol problem, such as lateness and absenteeism, poor work standards, impaired concentration, memory and judgement, and deteriorating relations with colleagues. It is always better to offer counselling rather than dismissal. The policy should be monitored to check on its effectiveness. Drug abuse presents similar problems to those found with alcohol abuse – absenteeism, reduced productivity and an increase in the risk of accidents. A recent study undertaken by Cardiff University found that ‘although drug use was lower among workers than the unemployed. One in four workers under the age of 30 years reported having used drugs in the previous year.… There are well documented links between drug use and impairments in cognition, perception, and motor skills, both at the acute and chronic levels. Associations may therefore exist between drug use and work performance’. The following conclusions were also drawn from the study: ➤ 13% of working respondents reported drug use in the previous year. The rate varied with age, from 3% of those over 50 to 29% of those under 30 ➤ drug use is strongly linked to smoking and heavy drinking in that order ➤ there is an association between drug use and minor injuries among those who are also experiencing other minor injury risk factors ➤ the project has shown that recreational drug use may reduce performance efﬁciency and safety at work. A successful drug misuse policy will beneﬁt the organization and employees by reducing absenteeism, poor productivity and the risk of accidents. There is no simple guide to the detection of drug abuse, but the HSE has suggested the following signals: ➤ ➤ ➤ ➤ ➤

sudden mood changes unusual irritability or aggression a tendency to become confused abnormal ﬂuctuations in concentration and energy impaired job performance

273

Introduction to Health and Safety at Work

Figure 15.13

Help needed here.

➤ poor time-keeping ➤ increased short-term sickness leave ➤ a deterioration in relationships with colleagues, customers or management ➤ dishonesty and theft (arising from the need to maintain an expensive habit). A policy on drug abuse can be established by: 1.

2.

3.

4.

Investigation of the size of the problem Examination of sicknesses, behavioural and productivity changes and accident and disciplinary records is a good starting point. Planning actions Develop an awareness programme for all staff and a special training programme for managers and supervisors. Employees with a drug problem should be encouraged to seek help in a conﬁdential setting. Taking action Produce a written policy that includes everyone in the organization and names the person responsible for implementing the policy. It should include details of the safeguards to employees and the conﬁdentiality given to anyone with a drug problem. It should also clearly outline the circumstances in which disciplinary action will be taken (the refusal of help, gross misconduct and possession/dealing in drugs). Monitoring the policy The policy can be monitored by checking for posi-

274

tive changes in the measures made during the initial investigation (improvements in the rates of sickness and accidents). Drug screening and testing is a sensitive issue and should only be considered with the agreement of the workforce (except in the case of pre-employment testing). Screening will only be acceptable if it is seen as part of the health policy of the organization and its purpose is to reduce risks to the misusers and others. Laboratories are accredited by the United Kingdom Accreditation Service (UKAS) and are able to undertake reliable testing. It is important to stress that some drugs are prescribed and controlled. The side effects of these can also affect performance and pose risks to colleagues. Employers should encourage employees to inform them of any possible side effects from prescribed medication and be prepared to alter work programmes accordingly.

15.9 Practice NEBOSH questions for Chapter 15 1. (a) Define the term ‘ergonomics’ (b) List SIX observations made during an inspection of a machine operation which may suggest that the machine has not been ergonomically designed.

Physical and psychological health hazards and control 2. In relation to work related upper limb disorders (WRULDs): (i) Identify the typical symptoms that might be experienced by affected individuals (ii) Outline the factors that would increase the risk of developing WRULDs. 3. (a) Identify TWO work activities that may give rise to work related upper limb disorders (WRULDs) (b) Outline measures that can be taken to reduce the risk of WRULDs. 4. The number of absences due to upper limb disorders in an organization appears to be increasing. Outline the possible sources of information that could be consulted when investigating this problem. 5. Outline the factors that could contribute towards the development of work-related upper limb disorders (WRULDs) amongst employees working at a supermarket checkout. 6. An increase in complaints of ill health effects associated with work-related upper limb disorder (WRULDs) has been reported amongst bricklayers who have been involved in building work on a long-term construction project. (i) Identify the typical symptoms the bricklayers would have shown (ii) Give reasons why the work undertaken by the bricklayers may increase the risk of them developing the condition (iii) Describe the measures that should be taken to minimize the risk to these workers. 7. In relation to the ill-health effects from the use of vibrating hand-held tools: (i) identify the typical symptoms that might be shown by affected individuals (ii) outline the control measures that may be used to minimize the risk of such effects. 8. Outline the factors to consider when making an assessment of a display screen equipment (DSE) workstation. 9. (a) Outline the possible risks to health associated with the use of display screen equipment (DSE) (b) Describe the precautionary measures which could be taken to eliminate or reduce the risks outlined in (a) above (c) Identify the features of a suitable seat for use at a DSE workstation.

10. A computer operator has complained of neck and back pain. Outline the features associated with the workstation that might have contributed towards this condition. 11. Employees who work for a computer manufacturer are required to solder components, some of which are less than 2 mm in size, onto printed circuit boards for up to 8 hours a day. (i) Giving reasons in EACH case, identify the risks to the health and safety of persons undertaking the work (ii) Outline the measures to take to minimize the risks identiﬁed in (i). 12. Outline the requirements of the Workplace (Health, Safety and Welfare) Regulations relating to the provision of welfare facilities. 13. Outline the health, safety and welfare issues that a company might need to consider before introducing a night shift to cope with an increased demand for its products. 14. Outline the speciﬁc factors that should be considered when assessing the risks to employees working on night shifts. 15. An ofﬁce building is about to be occupied by new owners. (i) Identify the factors that should be considered by the new owners when assessing the suitability of lighting within the building (ii) Other than lighting, outline FOUR factors associated the physical working environment that may affect the health and safety of employees (iii) Outline the requirements with respect to the welfare facilities that should be provided in the building. 16. Outline the factors to consider when assessing the adequacy of lighting within an open-plan ofﬁce. 17. (a) Outline the possible health risks associated with working in a seated position for prolonged periods of time (b) Outline the features of a suitable seat for ofﬁce work. 18. (a) Explain the following terms in relation to noise exposure at work: (i) ‘noise-induced hearing loss’ (ii) ‘tinnitus’. (b) Identify FOUR limitations of personal hearing protection as a means of protecting against the effects of noise.

275

Introduction to Health and Safety at Work 19. A pneumatic drill is to be used during extensive repair work to the ﬂoor of a busy warehouse. (i) Identify, by means of a labeled sketch, three possible transmission paths the noise from the drill could take. (ii) Outline appropriate control measures to reduce the noise exposures of the operator and the warehouse staff. 20. Maintenance workers in a factory are required to clean machinery on a regular basis using high pressure compressed air. Noise levels have been measured at 90 dB(A). (i) Explain the meaning of ‘dB(A)’ (ii) Outline the options that might be considered in order to reduce the risk of hearing damage BOTH to the maintenance staff AND to other employees (iii) Outline the criteria that should be used when selecting suitable hearing protection for the task, identifying the limitations of such protective equipment. 21. (a) Explain the meaning of the term ‘daily personal noise exposure’ (LEP’d) (b) Outline the actions required when employees’ exposure to noise are found to be in excess of 85 dB(A) LEP’d. 22. With respect to the Control of Noise at Work Regulations 2005: (i) state, in dB(A), Both the lower and the upper exposure action values (ii) outline the measures that the employer is required to take when employees are exposed to noise at or above an upper exposure action level. 23. An industrial washing machine has been installed on to the concrete ﬂoor of a bakery in order to clean the ﬂour off employees’ work clothes after their shift. When in use, employees are exposed to excessive noise levels that are emitted from the machine. (i) Identify FOUR possible affects on the health of the bakery employees from long-term exposure to the noise (ii) Outline practical measures that can be taken to reduce the levels of noise to which the employees are exposed. 24. Explain the meaning of the following terms in relation to noise control: (i) silencing (ii) absorption

276

(iii) damping (iv) isolation. 25. (a) Describe the TWO main types of personal hearing protection (b) Identify FOUR reasons why personal hearing protection may fail to provide adequate protection against noise (c) Outline the limitations of EACH of the above types of hearing protection. 26. (a) Identify the possible affects on health that may be caused by working in a hot environment such as a foundry (b) Outline measures that may be taken to help prevent the health affects identiﬁed in (a). 27. Outline the precautions to be taken to minimize the risks to persons working in cold stores operating at sub-zero temperatures. 28. (a) Identify the persons that an employer may need to appoint in order to comply with the Ionising Radiations Regulations (b) Outline the means of controlling exposure to ionising radiation. 29. (a) Identify TWO types of ionising radiation (b) Outline the ways in which exposure to ionising radiation at work may be controlled. 30. (a) Identify the possible affects on health arising from exposure to ionising radiation (b) Outline possible means of ensuring that workers are not exposed to unacceptable levels of ionising radiation. 31. (a) Identify TWO types of non-ionising radiation, giving an occupational source of each (b) Outline suitable control measures for ONE of the above sources of non-ionising radiation (c) Outline the health affects associated with exposure to non-ionising radiation. 32. (a) For each of the following types of non-ionising radiation, identify a source and state the possible ill health effects on exposed individuals: (i) infrared radiation (ii) ultraviolet radiation. (b) Identify the general methods for protecting people against exposure to non-ionising radiation. 33. Outline the factors that may lead to unacceptable levels of occupation stress amongst employees.

Physical and psychological health hazards and control 34. Other than those associated with the physical environment: (a) outline EIGHT possible causes of increased stress levels amongst employees (b) outline the options that might be available to an organization to reduce stress levels amongst its employees. 35. Inadequate lighting in the workplace may affect the level of stress amongst employees. Outline EIGHT

other factors associated with the physical environment that may increase stress at work. 36. Outline the practical measures that might be taken to reduce the risk of violence to employees who deal with members of the public as part of their work. 37. Outline FIVE possible indications that an employee may be suffering from alcohol or drug abuse.

Appendix 15.1 Smokefree workplace

Introduction Second-hand tobacco smoke is a major cause of heart disease and lung cancer amongst non-smokers who work with people who smoke. It is estimated that around 700 workers a year die as a direct result of second-hand tobacco smoke in their workplace. Second-hand smoke is also responsible for many thousands of episodes of illness. For example, Asthma UK reports that it is the second most common asthma trigger in the workplace. Eighty-two per cent of people with asthma say that other people’s smoke worsens their asthma and 1 in 5 people with asthma feel excluded from parts of their workplace where people smoke. In Summer 2007 legal restrictions on smoking in workplaces and public places were introduced in England. Similar legislation had been implemented in Wales and Scotland prior to that. The English legislation comes about through the Health Act 2006, which effectively bans smoking in all enclosed workplaces and public places, with some exemptions. The following information comes from the Department of Health website to ensure that it is correct for this radically new piece of legislation.

A quick guide to the new smokefree law ➤ England became smokefree on Sunday, 1 July 2007. The new law was introduced to protect employees and the public from the harmful effects of secondhand smoke. ➤ From 1 July 2007 it is against the law to smoke in virtually all enclosed public places, workplaces and public and work vehicles. There are be very few exemptions from the law. Indoor smoking rooms in virtually all public places and workplaces is no longer allowed.

➤ Managers of smokefree premises and vehicles have legal responsibilities to prevent people from smoking. ➤ The new law requires no-smoking signs to be displayed in all smokefree premises and vehicles. ➤ The new law applies to anything that can be smoked. This includes cigarettes, pipes (including water pipes such as shisha and hookah pipes), cigars and herbal cigarettes. ➤ Failure to comply with the new law is a criminal offence. Penalties and ﬁnes for smokefree offences are set out below (there are some discounted amounts for quick payment ): ➤ Smoking in smokefree premises or work vehicles: a ﬁxed penalty notice of £50 imposed on the person smoking. Or a maximum ﬁne of £200 if prosecuted and convicted by a court. ➤ Failure to display no-smoking signs: a ﬁxed penalty notice of £200 imposed on whoever manages or occupies the smokefree premises or vehicle. Or a maximum ﬁne of £1000 if prosecuted and convicted by a court. ➤ Failing to prevent smoking in a smokefree place: a maximum ﬁne of £2500 imposed on whoever manages or controls the smokefree premises or vehicle if prosecuted and convicted by a court. Local councils will be responsible for enforcing the new law. They will offer information and support to help businesses meet their legal obligations under the new law. You can ﬁnd out more information on the new law on the Smokefree England website at smokefreeengland.co.uk. You can also contact your local council for information.

277

16

Construction Construction activities – hazards activities – hazards and control and control

16.1 Introduction The construction industry covers a wide range of activities from large-scale civil engineering projects to very small house extensions. The construction industry has approximately 200 000 ﬁrms, of whom only 12 000 employ more than seven people – many of these ﬁrms are much smaller. The use of sub-contractors is very common at all levels of the industry. It is most likely that everybody will be aware or involved with some aspect of the construction industry at their place of work – either in terms of the repair and modiﬁcation of existing buildings or a major new engineering project. It is, therefore, important that the health and safety practitioner has some basic knowledge of the hazards and health and safety legal requirements associated with construction. Over many years, the construction industry has had a poor health and safety record. In 1966, there were 292 fatalities in the industry and by 1995 this ﬁgure had reduced to 62, but by 2000/2001 the ﬁgure had increased to 106. These ﬁgures include deaths of members of the public, including children playing on construction sites. Most of these fatalities (over 70%) were caused by falls from height. At a conference, organized by the Health and Safety Commission in February 2001, to address the problem, it was noted that at least two construction workers are being killed each week. Targets were set to reduce the number of fatalities and major injuries by 40% over a 4-year period. Due to the fragmented nature of the industry and its accident and ill-health record, the recent construction industry legal framework has concentrated on hazards

278

associated with the industry, welfare issues and the need for management and control at all stages of a construction project. In addition to the Health and Safety at Work Act 1974 and its associated relevant regulations, there are three sets of speciﬁc construction regulations which provide this legal framework, as follows: ➤ Construction (Head Protection) Regulations ➤ Construction (Design and Management) Regulations ➤ Work at Height Regulations A summary of these regulations is given in Chapter 17.

16.2 The scope of construction The scope of the construction industry is very wide. The most common activity is general building work which is domestic, commercial or industrial in nature. This work may be new building work, such as a building extension or, more commonly, the refurbishment, maintenance or repair of existing buildings. Larger civil engineering projects involving road and bridge building, water supply and sewage schemes and river and canal work all come within the scope of construction. The work could involve hazardous operations, such as demolition or roof work, or contact with hazardous materials, such as asbestos or lead. Construction also includes the use of woodworking workshops together with woodworking machines and their associated hazards, painting and decorating and the use of heavy machinery. It will often require work to take place in conﬁned spaces, such as excavations and underground chambers.

Construction activities – hazards and control Finally, at any given time, there are many young people receiving training on site in the various construction trades. These trainees need supervision and structured training programmes.

16.3 Construction hazards and controls The Construction (Design and Management (CDM) Regulations 2007 deal with many of the hazards likely to be found on a building site. In addition to these speciﬁc hazards, there will be the more general hazards (e.g. working at height, manual handling, electricity, noise, etc.) which have been discussed in more detail in earlier chapters. The hazards and controls identiﬁed in the CDM 2007 and Work at Height Regulations are as follows.

16.3.1

Safe place of work

Safe access to and egress from the site and the individual places of work on the site are fundamental to a good health and safety environment. This clearly requires that all ladders, scaffolds, gangways, stairways and passenger hoists are safe for use. It further requires that all excavations are fenced, the site is tidy and proper arrangements are in place for the storage of materials and the disposal of waste. The site needs to be adequately lit and secured against intruders, particularly children, when it is unoccupied. Such security will include: ➤ secure and locked gates with appropriate notices posted

Figure 16.1

➤ a secure and undamaged perimeter fence with appropriate notices posted ➤ all ladders either stored securely or boarded across their rungs ➤ all excavations covered ➤ all mobile plant immobilized and fuel removed, where practicable, and services isolated ➤ secure storage of all inﬂammable and hazardous substances ➤ visits to local schools to explain the dangers present on a construction site. This has been shown to reduce the number of child trespassers ➤ if unauthorized entry persists, then security patrols and closed circuit television may need to be considered.

16.3.2

Work at height

Work at height accounts for about 50–60 deaths – more than any other workplace activity – and 4000 injuries each year. This is being addressed by the introduction of the Work at Height Regulations which apply to all operations carried out at height, not just construction work, so that they are also relevant to, for example, window cleaning, tree surgery, maintenance work at height and the changing of street lamps. The Work at Height Regulations affect approximately 3 m workers where working at height is essential to their work. The Work at Height Regulations have no minimum height requirement for work at height. They include all work activities where there is a need to control a risk of falling a distance liable to cause personal injury. This is regardless of the work equipment being used, the duration of the work at height involved, or the height at

Secure site access gate.

279

Introduction to Health and Safety at Work which the work is performed. It includes access to and egress from a place of work. It would therefore include: ➤ Working on a scaffold or from a mobile elevated work platform (MEWP) ➤ Sheeting a lorry or dipping a road tanker ➤ Working on the top of a container in docks or on a ship or storage area ➤ Tree surgery and other forestry work at height ➤ Using cradles or rope for access to a building or other structure like a ship under repair ➤ Climbing permanent structures like a gantry or telephone pole ➤ Working near an excavation area or cellar opening if a person could fall into it and be injured ➤ Painting or pasting and erecting bill posters at height ➤ Work on staging or trestles. e.g. for ﬁlming or events ➤ Using a ladder/stepladder or kick stool for shelf ﬁlling, window cleaning and the like ➤ Using manriding harnesses in ship repair, off-shore or steeple jack work ➤ Working in a mine shaft or chimney ➤ Work carried out at a private house by a person employed for the purpose, e.g. painter and decorator (but not if the private individual carries out work on their own home).

➤ the employer shall take suitable and sufﬁcient measures to minimize the distance and consequences of a fall (collective measures, e.g. air bags or safety nets, must take precedence over individual measures, e.g. safety harnesses). The risk assessment and action required to control risks from using a kick stool to collect books from a shelf should be simple (e.g. not overloading, not overstretching, etc). However, the action required for a complex construction project would involve signiﬁcantly greater consideration and assessment of risk. A summary of the Regulations is given in Chapter 17.

16.3.3

Protection against falls from work at height

The Work at Height Regulations require that guard rails on scaffolds are at a minimum of 950 mm and the maximum unprotected gap between the toe and guard rail of a scaffold is 470 mm. This implies the use of an intermediate guard rail although other means, such as additional toe boards or screening, may be used. It also speciﬁes requirements for personal suspension equipment and means of arresting falls (such as safety nets). When working at height, a hierarchy of measures should then be followed, to prevent falls from occurring. These measures are:

However it would not include: ➤ Slips trips and falls on the same level ➤ Falls on permanent stairs if there is no structural or maintenance work being done ➤ Work in the upper ﬂoor of a multi storey building where there is no risk of falling (except separate activities like using a stepladder). At the centre of the regulations (Regulation 6), the employer is expected to apply a three stage hierarchy to all work which is to be carried out at height. The three steps are the avoidance of work at height, the prevention of workers from falling and the mitigation of the effect on workers of falls should they occur. The regulations require that: ➤ work is not carried out at height when it is reasonably practicable to carry the work out safely other than at height (e.g. the assembly of components should be done at ground level) ➤ when work is carried out at height, the employer shall take suitable and sufﬁcient measures to prevent, so far as is reasonably practicable, any person falling a distance liable to cause injury (e.g. the use of guard rails)

280

➤ avoid working at height, lf possible ➤ the provision of a properly constructed working platform, complete with toe boards and guard-rails ➤ if this is not practicable or where the work is of short duration, suspension equipment should be used and only when this is impracticable ➤ collective fall arrest equipment (air bags or safety nets) may be used. ➤ where this is not practicable individual fall restrainers (safety harnesses) should be used ➤ only when none of the above measures are practicable, should ladders of step ladders be considered.

16.3.4

Fragile roofs and surfaces

Work on or near fragile surfaces is also covered by the Work at Height Regulations (see summary in Chapter 17). Roof work, particularly work on pitched roofs, is hazardous and requires a speciﬁc risk assessment and method statement (see later under the management of construction activities for a deﬁnition) prior to the commencement of work. Particular hazards are fragile rooﬁng materials, including those materials which deteriorate and become more brittle with age and exposure to sunlight, exposed edges, unsafe access equipment

Construction activities – hazards and control

Figure 16.2

Proper precautions must always be taken when working on or near fragile roofs.

and falls from girders, ridges or purlins. There must be suitable means of access such as scaffolding, ladders and crawling boards. Suitable barriers, guard rails or covers where people work near to fragile materials and roof lights. Suitable warning signs indicating that a roof is fragile, should be on display at ground level. There are other hazards associated with roof work – overhead services and obstructions, the presence of asbestos or other hazardous substances, the use of equipment such as gas cylinders and bitumen boilers and manual handling hazards. It is essential that only trained and competent persons are allowed to work on roofs and that they wear footwear having a good grip. It is a good practice to ensure that a person does not work alone on a roof.

16.3.5

Protection against falling objects

Also now covered by the Work at Height Regulations (see summary of Chapter 17). Both construction workers and members of the public need to be protected from the hazards associated with falling objects. Both groups should be protected by the use of covered walkways or suitable netting to catch falling debris. Waste material should be brought to ground level by the use of chutes or hoists. Waste should not be thrown and only minimal quantities of building materials should be stored on working platforms. The Construction (Head Protection) Regulations 1989 virtually mandates employers to supply head protection (hard hats) to employees whenever there is a risk of head injury from falling objects. (Sikhs wearing turbans are exempted from this requirement.) The employer is also responsible for ensuring that hard hats are properly maintained and replaced when they are damaged in any way. Self-employed workers must supply and maintain their own head protection. Visitors to construction sites should always be supplied with

head protection and mandatory head protection signs displayed around the site.

16.3.6

Demolition

Demolition is one of the most hazardous construction operations and is responsible for more deaths and major injuries than any other activity. The management of demolition work is controlled by the Construction (Design and Management) Regulations and requires a planning supervisor and a health and safety plan (see the next section of this chapter). The principal hazards associated with demolition work are: ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

falls from height or on the same level falling debris premature collapse of the structure being demolished dust and fumes the silting up of drainage systems by dust the problems arising from spilt fuel oils manual handling presence of asbestos and other hazardous substances noise and vibration from heavy plant and equipment electric shock ﬁres and explosions from the use of ﬂammable and explosive substances smoke from burning waste timber pneumatic drills and power tools the existence of services, such as electricity, gas and water collision with heavy plant, and plant and vehicles overturning.

Before any work is started, a full site investigation must be made by a competent person to determine the

281

Introduction to Health and Safety at Work hazards and associated risks which may affect the demolition workers and members of the public who may pass close to the demolition site. The investigation should cover the following topics: ➤ construction details of the structures or buildings to be demolished and those of neighbouring structures or buildings ➤ the presence of asbestos, lead or other hazardous substances ➤ the location of any underground or overhead services (water, electricity, gas, etc.) ➤ the location of any underground cellars, storage tanks or bunkers, particularly if ﬂammable or explosive substances were previously stored ➤ the location of any public thoroughfares adjacent to the structure or building. The CDM co-ordinator, who is responsible for notifying the Health and Safety Executive of the proposed demolition work, must ensure that a written risk assessment is made of the design of the structure to be demolished and the inﬂuence of that design on the demolition method proposed. This risk assessment will normally be made by the project designer who will also plan the demolition work. A further risk assessment should then be made by the contractor undertaking the demolition – this risk assessment will be used to draw up a method statement for inclusion in the health and safety plan. A written method statement will be required before demolition takes place. The contents of the method statement will include the following: ➤ details of method of demolition to be used, including the means of preventing premature collapse or the collapse of adjacent buildings and the safe removal of debris from upper levels ➤ details of equipment, including access equipment, required and any hazardous substances to be used ➤ arrangements for the protection of the public and the construction workforce, particularly if hazardous substances, such as asbestos or other dust, are likely to be released ➤ details of the isolation methods of any services which may have been supplied to the site and any temporary services required on the site ➤ details of personal protective equipment which must be worn ➤ ﬁrst aid, emergency and accident arrangements ➤ training and welfare arrangements ➤ arrangements for waste disposal ➤ names of site foremen and those with responsibility for health and safety and the monitoring of the work ➤ COSHH and other risk assessments (personal protective equipment, manual handling, etc.) should be appended to the method statement.

282

There are two forms of demolition: ➤ piecemeal – where the demolition is done using hand and mechanical tools such as pneumatic drills and demolition balls ➤ deliberate controlled collapse – where explosives are used to demolish the structure. This technique should only be used by trained, specialist competent persons. A very important element of demolition is the training required by all construction workers involved in the work. Specialist training courses are available for those concerned with the management of the process, from the initial survey to the ﬁnal demolition. However, induction training, which outlines the hazards and the required control measures, should be given to all workers before the start of the demolition work. The site should be made secure with relevant signs posted to warn members of the public of the dangers.

16.3.7

Excavations

This topic will be covered in more detail later in this chapter. Excavations must be constructed so that they are safe environments for construction work to take place. They must also be fenced and suitable notices posted so that neither people nor vehicles fall into them as required by the Work at Height Regulations.

16.3.8

Prevention of drowning

Where construction work takes place over water, steps should be taken to prevent people falling into the water and rescue equipment should be available at all times.

16.3.9

Vehicles and traffic routes

All vehicles used on site should be regularly maintained and records kept. Only trained drivers should be allowed to drive vehicles and the training should be relevant to the particular vehicle (fork lift truck, dumper truck, etc.). Vehicles should be ﬁtted with reversing warning systems. HSE investigations have shown that in over 30% of dumper truck accidents, the drivers had little experience and no training. Common forms of accident include driving into excavations, overturning while driving up steep inclines and runaway vehicles which have been left unattended with the engine running. Many vehicles such as mobile cranes require regular inspection and test certiﬁcates. The small dumper truck is widely used on all sizes of construction site. Compact dumper trucks are involved

Construction activities – hazards and control

Figure 16.3

Barriers around excavation by footpath.

in about 30% of construction transport accidents. The three main causes of such accidents are: ➤ overturning on slopes and at the edges of excavations ➤ poorly maintained braking systems, and ➤ driver error due to lack of training and/or inexperience. Some of the hazards associated with this vehicle are: collisions with pedestrians, other vehicles or structures, such as scaffolding etc. They can be struck by falling materials and tools or be overloaded. The person driving the truck can be thrown from the vehicle, come into contact with moving parts on the truck, suffer the effects of whole body vibrations due to driving over potholes in the roadway and suffer from the effects of noise and dust. The precautions that can be taken to address these hazards include the use of authorized, trained, competent and supervised drivers only. As with so many other construction operations, risks should be assessed, safe systems of work followed and drivers forbidden from taking shortcuts. The following site controls should also be in place: ➤ ➤ ➤ ➤ ➤

designated trafﬁc routes and signs speed limits stop blocks used when the vehicle is stationary proper inspection and maintenance procedures procedures for starting, loading and unloading the vehicle ➤ provision of roll-over protective structures (ROPS) and seat restraints

➤ provision of falling-object protective structures (FOPS) when there is a risk of being hit by falling materials ➤ visual and audible warning of approach ➤ where necessary, hearing protection. For other forms of mobile construction equipment, such as fork lift trucks (covered in chapter 12), the risk to people from the overturning of the equipment must always be safeguarded. This can usually be achieved by the avoidance of working on steep slopes, the provision of stabilizers and ensuring that the load carried does not affect the stability of the equipment/vehicle. Chapter 14 describes the hazards, safeguards and precautions for several pieces of equipment and machinery used in construction work, such as the cement/concrete mixer and the bench-mounted circular saw. Trafﬁc routes and loading and storage areas need to be well designed with enforced speed limits, good visibility and the separation of vehicles and pedestrians being considered. The use of one-way systems and separate site access gates for vehicles and pedestrians may be required. Finally, the safety of members of the public must be considered, particularly where vehicles cross public footpaths.

16.3.10

Fire and other emergencies

Emergency procedures relevant to the site should be in place to prevent or reduce injury arising from ﬁre, explosions, ﬂooding or structural collapse. These procedures should include the location of ﬁre points and assembly

283

Introduction to Health and Safety at Work points, extinguisher provision, site evacuation, contact with the emergency services, accident reporting and investigation and rescue from excavations and conﬁned spaces. There also needs to be training in these procedures at the induction of new workers and ongoing for all workers.

16.3.11

Welfare facilities

The Health and Safety Executive has been concerned for some time at the poor standard of welfare facilities on many construction sites. Sanitary and washing facilities (including showers if necessary) with an adequate supply of drinking water should be provided for everybody working on the site. Accommodation will be required for the changing and storage of clothes and rest facilities for break times. There should be adequate ﬁrst-aid provision (an accident book) and protective clothing against adverse weather conditions.

16.3.12

Electricity

Electrical hazards have been covered in detail earlier in Chapter 12, and all the control measures mentioned apply on a construction site. However, due to the possibility of wet conditions, it is recommended that only 110 V equipment is used on site. Where mains electricity is used (perhaps during the ﬁnal ﬁtting out of the building), then residual current devices should be used with all equipment. Where workers or tall vehicles are working near or under overhead power lines, either the power should be turned off or ‘goal posts’ or taped markers used to prevent contact with the lines. Similarly, underground supply lines should be located and marked before digging takes place.

16.3.13

Noise

Noisy machinery should be ﬁtted with silencers. When machinery is used in a workshop (such as woodworking machines), a noise survey should be undertaken and, if the noise levels exceed the second action level, the use of ear defenders becomes mandatory.

16.3.14

Health hazards

Health hazards are present on a construction site. These hazards include vibration, dust (including asbestos), cement, solvents and paints and cleaners. A COSHH assessment is essential before work starts with regular updates as new substances are introduced. Copies of the assessment and the related safety data sheets should be kept in the site ofﬁce for reference after accidents or ﬁres. They will also be required to check that

284

the correct personal protective equipment is available. A manual handling assessment should also be made to ensure that the lifting and handling of heavy objects is kept to a minimum. Many of the health hazards (both chemical and biological) are covered in Chapter 14 including silica which is a commonly produced during construction activities. Such activities which can expose workers and members of the public to silica dust include: ➤ cutting building blocks and other stone masonry work ➤ cutting and/or drilling paving slabs and concrete paths ➤ demolition work ➤ sand blasting of buildings, and ➤ tunnelling. In general, the use of power tools to cut or dress stone and other silica containing materials will lead to very high exposure levels while the work is occurring. In most cases, exposure levels are in excess of workplace exposure limits (WELs) by factors greater than 2 and in some cases as high as 12. In response to the growing evidence of ill-health effects of silica inhalation, the HSE has recently revised the workplace exposure limit down from 0.3 mg/m3 to 0.1 mg/m3. The inhalation of very ﬁne silica dust can lead to the development of silicosis. HSE have produced a detailed information sheet on silica – CIS No 36 (Rev 1). In addition to silica, there are three additional hazardous substances that are particularly relevant to construction activities – cement dust and wet cement, wood dust and the biological hazard tetanus. Cement dust and wet cement is an important construction and is also a hazardous substance. Contact with wet cement can cause serious burns or ulcers which will take several months to heal and may need a skin graft. Dermatitis, both irritant and allergic, can be caused by skin contact with either wet cement or cement powder. Allergic dermatitis is caused by an allergic reaction to hexavalent chromium (chromate) which is present in cement. Cement powder can also cause inﬂammation and irritation of the eye, irritation of the nose and throat, and, possibly, chronic lung problems. Research has shown that between 5% and 10% of construction workers are probably allergic to cement. And plasterers, concreters and bricklayers or masons are particularly at risk. A plasterer, who knelt in wet cement for 5 hours while working, required skin grafts to his legs. Manual handling of wet cement or cement bags can lead to musculoskeletal health problems and cement bags weighing more that 25 kg should not be carried by a single worker. Personal protective equipment in the form of gloves, overalls with long sleeves and full length trousers and waterproof boots must be worn on

Construction activities – hazards and control all occasions. If the atmosphere is dusty, goggles and respiratory protection equipment must be worn. An important factor in the possibility of dermatitis occurring is the sensitivity of the worker to the chromate in the cement and the existing condition of the skin including cuts and abrasions. Finally, adequate welfare facilities are essential so that workers can wash their hands at the end of the job and before eating, drinking or using the toilet. If cement is left on the skin for long periods without being washed off, the risk of an allergic reaction to hexavalent chromium will increase. A 2005 amendment to the COSHH Regulations prohibits the supply of cement which has a concentration of more than 2 parts per million of Chromium VI. This measure is designed to prevent allergic contact dermatitis when wet cement comes into contact with the skin. However, since the strong alkalinity of cement will remain, there is still the potential for skin burns. The Approved Code of Practice gives useful advice on possible control measures by offering two routes for employers to comply with the amended COSHH Regulations. They can either use the generic advice given in COSHH Essentials HSG193 or design a solution themselves with the help of competent advice. In any event, the controls should be proportionate to the health risk. The regulations stress the need to provide adequate washing, changing, eating and drinking facilities. Wood dust can be hazardous, particularly when it is hard wood dust which is known, in rare cases, to lead to nasal cancer. Composite boards, such as medium-density ﬁbreboard (MDF), are hazardous due to the resin bonding material used which also can be carcinogenic. There are three types of wood based boards available: laminated board, particle board and ﬁbreboard. The resins used to bond the ﬁbreboard together contain formaldehyde (usually urea formaldehyde). It is generally recognised that formaldehyde is ‘probably carcinogenic to humans’ and is subject to a workplace exposure limit (WEL). At low exposure levels, it can cause irritation to the eyes, nose and throat and can lead to dermatitis, asthma and rhinitis. The main problems are most likely to occur when the MDF is being machined and dust is produced. A suitable risk assessment should be made and gloves and appropriate masks should always be worn when machining MDF. However, it is important to stress that safer materials are available which do not contain formaldehyde and these should be considered for use in the ﬁrst instance. Wood dust is produced whenever wood materials are machined, particularly sawed, sanded, bagged as dust from dust extraction units or during cleaning operations especially if compressed air is used. The main hazards associated with all wood dusts are skin disorders, nasal problems, such as rhinitis, and asthma. There is also a hazard from ﬁre and explosion. A COSHH

assessment is essential to show whether the particular wood dust is hazardous. When the wood dust is created inside a woodworking shop a well-designed extraction system is essential. Personal protective equipment in the form of gloves, suitable respiratory protective equipment, overalls and eye protection may also be necessary as a result of the assessment. Finally, good washing and welfare facilities are also essential. Tetanus is a serious, sometimes fatal, disease caused by a bacterium that lives in the soil. It usually enters the human body through a wound from an infected object, such as a nail, wood splinter or thorn. On entering the wound, it produces a powerful toxin which attacks the nerves that supply muscle tissue. It is commonly known as lockjaw because after an incubation period of approximately a week, stiffness of around the jaw area occurs. Later the disease spreads to other muscles including the breathing system and this can be fatal. The disease has been well controlled with anti-tetanus immunization and it is important that all construction workers are so immunized. Booster shots should be obtained every few years. Any ﬂesh wound should be thoroughly cleaned immediately and an anti-septic cream applied. Other health hazards which could affect construction workers are noise, vibration, asbestos, solvents, fumes, radiation (particularly from sunlight) and biological hazards, such as leptospirosis from sewer work). Health surveillance may well be required for some of these hazards (see Chapter 14).

16.3.15

Waste disposal

The collection and removal of waste from a construction site is normally accomplished using a skip. The skip should be located on ﬁrm, level ground away from the main construction work, particularly excavation work. This will allow clear access to the skip for ﬁlling and removal from site. On arrival on site, the integrity of the skip should be checked. It should be ﬁlled either by chute or by mechanical means unless items can be placed in by hand. Skips should not be overﬁlled and be netted or sheeted over when it is full. Any hazardous waste should be segregated as described in Chapter 14 which also mentioned disposal procedures.

16.4 The management of construction activities 16.4.1

Introduction

The management of construction work, including the selection and control of contractors, is governed by the

285

Introduction to Health and Safety at Work Construction (Design and Management) Regulations 2007 known as the CDM 2007. The CDM Regulations apply to the whole of a construction project, from the initial feasibility study to the hand-over of the completed structure to the customer. CDM 2007 came into force on 6 April 2007. They replace the Construction (Design and Management) Regulations 1994 (CDM 94) and the Construction (Health, Safety and Welfare) Regulations 1996 (CHSW). The new Approved Code of Practice replaces the ACOP under CDM 94. The key aim of the of CDM 2007 is to integrate health and safety into the management of the project and to encourage everyone involved to work together to. CDM 2007 is split into several main Parts: ➤ Part 2 – covers all construction projects and sets out general management duties ➤ Part 3 – sets out additional duties where the project is notiﬁable ➤ Part 4 – sets out the duties relating to health and safety on construction sites schedule 2 welfare arrangements (largely the former Construction (Health, safety and welfare) Regulations 1996 More details of CDM 2007 are given in Chapter 17.

16.4.2 Explanation of terms used in the CDM 2007 and Approved Code of Practice A CLIENT is an organization or individual for whom a construction project is carried out. Clients only have duties when the project is associated with a business or other undertaking (whether for proﬁt or not). This can include for example, local authorities, school governors, insurance companies and project originators or Private Finance Initiative (PFI) projects. Domestic clients are a special case and do not have duties under CDM 2007. Designer: Designers are those who have a trade or a business which involves them in: ➤ Preparing designs for construction work, including variations. This includes preparing drawings, design details, speciﬁcations, bills of quantities and the speciﬁcation (or prohibition) of articles and substances, as well as all the related analysis, calculations, and preparatory work; or ➤ Arranging for their employees or other people under their control to prepare designs relating to a structure or part of a structure. It does not matter whether the design is recorded (e.g. on paper or a computer) or not (e.g. it is only communicated orally).

286

Designers may include: ➤ architects, civil and structural engineers, building surveyors, landscape architects, other consultants, manufacturers and design practices (of whatever discipline) contributing to, or having overall responsibility for, any part of the design, for example drainage engineers ➤ anyone who speciﬁes or alters a design, or who speciﬁes the use of a particular method of work or material, such as a design manager, quantity surveyor who insists on speciﬁc material or a client who stipulates a particular layout for a new building ➤ building service designers, engineering practices or others designing plant which forms part of the permanent structure (including lifts, heating, ventilation and electrical systems), for example a specialist provider of permanent ﬁre extinguishing installations ➤ those purchasing materials where the choice has been left open, for example those purchasing building blocks and so deciding the weights that a bricklayer must handle ➤ contractors carrying out design work as part of their contribution to a project, such as an engineering contractor providing design, procurement and construction management services ➤ temporary works engineers, including those designing auxiliary structures, such as formwork, falsework, façade retention schemes, scaffolding and sheet piling ➤ interior designers, including shop-ﬁtters who also develop the design ➤ heritage organizations who specify how work is to be done in detail, for example providing detailed requirements to stabilize existing structures, and ➤ those determining how buildings and structures are altered, e.g. during refurbishment, where this has the potential for partial or complete collapse. CDM co-ordinator: means the person appointed as the CDM co-ordinator under regulation 14.(1) for notiﬁable projects only. The CDM Co-ordinator provides clients with a key project advisor in respect of construction health and safety risk management matters. Their main purpose is to help clients to carry out their duties; to co-ordinate health and safety aspects of the design work and to prepare the health and safety ﬁle. Principal contractor: This is the contractor appointed by the client for notiﬁable projects. The principal contractor can be an organization or an individual, and is the main or managing contractor. A principal contractor’s key duty is to co-ordinate and manage the construction phase to ensure the health and safety of everybody carrying out construction work, or who are affected by the work.

Construction activities – hazards and control Pre-construction health and safety information: The client must provide to designers and contractors and for notiﬁable projects the CDM co-ordinator speciﬁc health and safety information needed to identify the hazards and risks associated with the design and construction work. The information needs to be identiﬁed, assembled and sent out in good time, so that those who need it when preparing a bid or preparing for work can decide what resources will be needed to enable design, planning and construction work to be organized and carried out properly. The topics which should be addressed in the preconstruction information are given in Appendix 16.3.

Construction Phase Health and Safety Plan Principal Contractors must set out the way in which the construction phase will be managed and the key health and safety issues for the particular project must be set out in writing. The health and safety plan should set out the organization and arrangements that have been put in place to manage risks and co-ordinate the work on site. It should not be a repository for detailed generic risk assessments, records of how decisions were reached or detailed method statements; but it may, for example, set out when such documents will need to be prepared. It should be well focused, clear and easy for contractors and others to understand – emphasizing key points and avoiding irrelevant material. It is crucial that all relevant parties are involved and co-operate in the development and implementation of the plan as work progresses. The plan must be tailored to the particular project. Generic plans will not satisfy the requirements of Regulation 23. Photographs and sketches can greatly simplify and shorten explanations. It should also be organized so that relevant sections can easily be made available to designers and contractors. The Construction Phase health and safety plan for the initial phase of the construction work must be prepared before any work begins. Later details may need to be added as work and full designs become available. See Appendix 16.4 for details of what should be included in the Health and Safety Plan. Health and safety file This is a record of information for the client to retain which focuses on health and safety. It alerts those who are responsible for the structure and equipment in it of the signiﬁcant health and safety risks that will need to be dealt with during subsequent use, construction, maintenance, cleaning, repair, alterations, refurbishment and demolition work. See later for further information on the ﬁle. Method statement This is a written document laying out the work procedures and sequences of operations to

ensure health and safety. It results from the risk assessment carried out for the task or operation and the control measures identiﬁed. If the risk is low, a verbal statement may sufﬁce. Notifiable work Construction work (except for a domestic client) is notiﬁable to the Health and Safety Executive if it lasts longer than 30 working days or will involve more than 500 person days of work, e.g. 50 people working for 10 days. Holidays and weekends do not count if no construction work takes place on those days. The CDM co-ordinator is responsible to make the notiﬁcation as soon as possible after their appointment for a particular project. The notice must be displayed where it can be read by people working on the site. See Chapter 17 for details of the information required.

16.4.3

Part 1 Non-notifiable Projects Responsibilities of Duty Holders

A summary of duties is shown in table 17.3 in Chapter 17. Also see the ﬂow diagram in Appendix 16.2. The ACOP for CDM 2007 covers the competence of each duty holder in some depth. This is an essential part of the effective management of construction projects. The ACOP should be consulted for further details. Co-ordination and co-operation is a requirement for all members of the project team. However there is no requirement for the appointment of a CDM co-ordinator, principal contractor or a construction-phase health and safety plan for non-notiﬁable projects. For low risk projects a low-key approach will sufﬁce. However for higher risk projects, e.g. those involving demolition, a more rigorous approach is required. The architect or lead designer should normally lead the co-ordination of the design work while the main contractor or builder should co-ordinate the construction work. A brief summary plan may be all that is required in many cases but where the risks are higher, something close to the construction phase plan will be needed. For example where work involves: ➤ structural alterations ➤ deep excavations, and those in unstable or contaminated ground ➤ unusual working methods or safeguards ➤ ionising radiation or other signiﬁcant health hazards ➤ nearby high voltage power-lines ➤ a risk of falling into water which is, or may become fast ﬂowing ➤ diving ➤ explosives ➤ heavy or complex lifting operations.

287

Introduction to Health and Safety at Work For all Demolition work those in control of the work are required to produce a written plan showing how danger will be prevented.

Clients (Non domestic) Clients are not expected to manage or plan projects themselves. They are not expected to develop substantial expertise in construction health and safety, unless this is central to their business. Clients must ensure that various things are done, but are not normally expected to do them themselves. If help is needed this should be available from the competent person appointed under Regulation 7 of the Management of Health and Safety at Work Regulations 1999. Alternatively clients could seek advice from someone who has acted as a CDM co-ordinator on other projects. (The appointment of a CDM co-ordinator is not a requirement for non-notiﬁable projects.) The client must make sure that: ➤ designers, contractors and others who they propose to engage are competent or work under the supervision of competent people, are adequately resourced and appointed early enough to fulﬁl their duties ➤ they allow sufﬁcient time for each stage of the project ➤ they co-operate with others concerned as necessary to allow people to fulﬁl their duties ➤ they co-ordinate their own work with others to ensure the safety of those carrying out the construction work ➤ there are reasonable management arrangements in place throughout the project to ensure the work can be carried out, so far as is reasonably practicable, safely and without risks to health (this does not mean managing the risk themselves as few clients have the expertise) ➤ contractors have made arrangements for suitable welfare facilities to be provided from the start and throughout the project ➤ any ﬁxed workplaces which are to be constructed comply with the Workplace (Health Safety and welfare) Regulations ➤ relevant information (pre-construction information) likely to be needed by designers, contractors or others to plan and manage the work is passed to them. Clients should make periodic checks through the life of the project, for example to: ➤ check there is adequate protection for the client’s workers and/or members of the public ➤ check that adequate welfare facilities have been provided by the contractor ➤ check that there is good co-operation and communication between designers and contractors

288

➤ check that the arrangements which the contractor agreed to make to control key risks on site have been implemented.

Designers Designers should: ➤ make sure they are competent and adequately resourced to address the health and safety issues likely to be involved in the design ➤ check that clients are aware of duties ➤ when designing the project, avoid foreseeable risks to those involved in the construction and future use of the structure, and in so doing, they should eliminate hazards, so far as is reasonably practicable, and reduce risk associated with the hazards that remain ➤ provide adequate information about any signiﬁcant risks associated with the design ➤ co-ordinate their work with that of others in order to improve the way in which risks are managed and controlled. Designers need to consider risks to those carrying out the construction work; those cleaning and maintaining the structure (particularly windows or translucent panels; those who use the structure for a workplace; and those who may be affected by the work, e.g. the public or other customers.

Contractors For all projects contractors must: ➤ check clients are aware of their duties ➤ satisfy themselves that they and anyone they employ or engage are competent and adequately resourced ➤ plan, manage and monitor their own work to make sure that workers under their control are safe from the start of their work ➤ ensure that any contractor who they appoint or engage to work on the project is informed of the minimum amount of time which will be allowed for them to plan and prepare before starting work ➤ provide workers under their control (whether employed or self-employed) with any necessary information, including about relevant aspects of other contractors’ work, and site induction which they need to work safely, to report problems or to respond appropriately in an emergency ➤ ensure that any design work they do complies with the requirements on designers in Regulation 11 ➤ comply with any relevant requirement in Part 4 and schedule 2 of the regulations regarding health and safety on construction sites ➤ co-operate with others and co-ordinate their own work with others working on the project

Construction activities – hazards and control ➤ Obtain specialist advice where necessary when planning high risk work, e.g. alterations that could result in a structural collapse or is on contaminated ground.

16.4.4 Notifiable projects – additional responsibilities of duty holders Clients For notiﬁable projects the client has the following additional duties: ➤ Appoint a CDM co-ordinator to advise and assist with their duties and to co-ordinate the arrangements for health and safety during the planning phase ➤ Appoint a principal contractor to plan and manage the construction work – preferably early enough for them to work with the designer on issues relating to buildability, usability and maintainability ➤ Ensure that the construction phase does not start until the principal contractor has prepared a suitable health and safety plan and made arrangements for suitable welfare facilities to be present from the start of the work ➤ Make sure the health and safety ﬁle is prepared, reviewed, or updated ready for handover at the end of the construction work. This must be kept available for any future construction work or to pass onto a new owner. Early appointments are essential as the client is likely to have to rely on the advice from the CDM co-ordinator on the competence of appointees and the adequacy of the arrangements. If a client does not make these appointments they are liable for the work of the CDM coordinator and the principal contractor as well as not making the appointment.

CDM co-ordinators CDM co-ordinators must: ➤ give suitable and sufﬁcient advice and assistance to clients in order to help them to comply with their duties, in particular: ➤ the duty to appoint competent designers and contractors; and ➤ the duty to ensure that adequate arrangements are in place for managing the project ➤ notify the HSE about the project ➤ co-ordinate design work, planning and other preparation for construction where relevant to health and safety ➤ identify and collect the pre-construction information and advise the client if surveys need to be commissioned to ﬁll signiﬁcant gaps

➤ promptly provide in a convenient form to those involved with the design of the structure; and to every contractor (including the principal contractor) who may be or has been appointed by the client, such parts of the pre-construction information which are relevant to each ➤ manage the ﬂow of health and safety information between clients designers and contractors ➤ advise the client on the suitability of the initial construction phase plan and the arrangements made to ensure that welfare facilities are on site from the start ➤ produce or update a relevant, user friendly, health and safety ﬁle suitable for future use at the end of the construction phase.

Designers For notiﬁable projects designers have the following additional duties: ➤ ensure that the client has appointed a CDM co-ordinator and notiﬁed HSE ➤ ensure that they do not start design work other than initial design work unless a CDM co-ordinator has been appointed ➤ co-operate with the CDM co-ordinator, principal contractor and with any other designers or contractors as necessary for each of them to comply with their duties. This includes providing any information needed for the pre-construction information pack or health and safety ﬁle.

The Principal contractor Principal contractors must: ➤ satisfy themselves that clients are aware of their duties, that a CDM co-ordinator has been appointed and HSE notiﬁed before work starts ➤ make sure that they are competent to address the health and safety issues likely to be involved in the management of the construction project phase ➤ ensure that the construction phase is properly planned, managed and monitored, with adequately resourced, competent site management appropriate to the risk and activity ➤ ensure that every contractor who will work on the project is informed of the minimum amount of time which they will be allowed for planning and preparation before they begin work on site ➤ ensure that all contractors are provided with the information about the project that they need to enable them to carry out their work safely and without risks to health. Requests from contractors for information should be met promptly

289

Introduction to Health and Safety at Work ➤ ensure that a suitable construction phase health and safety plan is: ➤ prepared before construction work begins ➤ developed in discussion with, and communicated to, contractors affected by it ➤ implemented, and ➤ kept up to date as the project progresses. ➤ satisfy themselves that the designers and contractors they engage are competent and adequately resourced ➤ ensure suitable welfare facilities are provided from the start of the construction phase ➤ take reasonable steps to prevent unauthorized access to the site; prepare and enforce any necessary site rules ➤ provide (copies of or access to) relevant parts of the health and safety plan and other information to contractors including the self-employed in time for them to plan their work ➤ liaise with the CDM co-ordinator on design carried out during the construction phase, including design by specialist contractors, and its implications for the health and safety plan ➤ provide the CDM co-ordinator promptly with any information relevant to the health and safety ﬁle ➤ ensure that all the workers have been provided with suitable health and safety induction, information and training ➤ ensure that the workforce is consulted about health and safety matters ➤ display the project notiﬁcation.

16.4.5

The client should make sure that the CDM co-ordinator compiles the ﬁle. What is needed should be agreed in advance so that designers and contractors can produce the relevant documents as their work progresses. The ﬁle is a key part of the information that a client or their successors will need for future construction projects and so should be kept up-to-date after any relevant surveys or work. A ﬁle must be produced or updated (if one already exists) as part of all notiﬁable projects. CDM 2007 allows one ﬁle to be maintained for a site and then updated after subsequent projects have been completed. The information which should be included where they are relevant to the health and safety of any future construction project, is given in Chapter 17.

16.4.6

Selection and control of contractors

It is important that health and safety factors are considered as well as technical or professional competence when potential contractors are being short listed or employed. The following items will give a guide to health and safety attitudes:

The health and safety file

The health and safety ﬁle is a record of relevant information for the client or his customer. It will be developed as the construction progresses with various designers or contractors adding information as it becomes available. The ﬁle should be useful to: ➤ clients who have a duty to provide information about their premises to those who carry out work there ➤ designers during the development of further designs or alterations ➤ CDM co-ordinators preparing for construction work ➤ principal contractors and contractors preparing to carry out or manage such work. A number of people have legal duties with respect to the health and safety ﬁle: ➤ CDM co-ordinators must prepare review, amend or add to the ﬁle as the project progresses, and give it to the client at the end of the project

290

➤ clients, designers, principal contractors and other contractors must supply the information necessary for compiling or updating the ﬁle ➤ clients must keep the ﬁle to assist with future construction work, and ➤ everyone providing information should make sure that it is accurate, and provided promptly.

➤ registration with either the HSE or Environmental Health Department of a Local Authority ➤ a current health and safety policy ➤ details of any risk assessments made and control measures introduced ➤ any method statements required to perform the contract ➤ details of competence certiﬁcation, particularly when working with gas or electricity may be involved ➤ details of insurance arrangements in force at the time of the contract ➤ details of emergency procedures, including ﬁre precautions, for contractor employees ➤ details of any previous accidents or incidents reported under RIDDOR ➤ details of accident reporting procedure ➤ details of previous work undertaken by the contractor ➤ references from previous employers or main contractors ➤ details of any health and safety training undertaken by the contractor and his employees.

Construction activities – hazards and control On being selected, contractors should be expected to: ➤ familiarize themselves with those parts of the health and safety plan which affect them and their employees and/or sub-contractors ➤ cooperate with the principal contractor (or main if non-notiﬁable project) in their health and safety duties to contractors ➤ comply with their legal health and safety duties. On arrival at the site, sub-contractors should ensure that: ➤ they report to the site ofﬁce on arrival on site and report to the site manager ➤ they abide by any site rules, particularly in respect of personal protective equipment ➤ the performance of their work does not place others at risk ➤ they are familiar with the ﬁrst aid and accident reporting arrangements of the principal contractor ➤ they are familiar with all emergency procedures on the site ➤ any materials brought onto the site are safely handled, stored and disposed of in compliance, where appropriate, with the current Control of Substances Hazardous to Health Regulations ➤ they adopt adequate ﬁre precaution and prevention measures when using equipment which could cause ﬁres ➤ they minimize noise and vibration produced by their equipment and activities ➤ any ladders, scaffolds and other means of access are erected in conformance with good working practice and the Work at Height Regulations ➤ any welding or burning equipment brought onto the site is in safe operating condition and used safely with a suitable ﬁre extinguisher to hand ➤ any lifting equipment brought onto the site complies with the current Lifting Operation and Lifting Equipment Regulations ➤ all electrical equipment complies with the current Electricity at Work Regulations ➤ connections to the electricity supply is from a point speciﬁed by the principal contractor and is by proper cables and connectors. For outside construction work, only 110 V equipment should be used ➤ any restricted access to areas on the site is observed ➤ welfare facilities provided on site are treated with respect ➤ any vehicles brought onto the site observe any speed, condition or parking restriction. The control of sub-contractors can be exercised by monitoring them against the criteria listed above and by regular site inspections. On completion of the contract,

the work should be checked to ensure that the agreed standard has been reached and that any waste material has been removed from the site.

16.5 Working above ground level or where there is a risk of falling 16.5.1

Hazards and controls associated with working above ground level

The signiﬁcance of injuries resulting from falls from height, such as fatalities and other major injuries, have been dealt with earlier in the chapter as has the importance and legal requirements for head protection. Also covered were the many hazards involved in working at height, including fragile roofs and the deterioration of materials, unprotected edges and falling materials. Additional hazards include the weather and unstable or poorly maintained access equipment, such as ladders and various types of scaffold. The principal means of preventing falls of people or materials includes the use of fencing, guardrails, toe boards, working platforms, access boards, ladder hoops, safety nets and safety harnesses. Safety harnesses arrest the fall by restricting the fall to a given distance due to the ﬁxing of the harness to a point on an adjacent

Figure 16.4 Ladders should be correctly angled one out for every four up.

291

Introduction to Health and Safety at Work rigid structure. They should only be used when all other possibilities are not practical. ➤

16.5.2

Access equipment

There are many different types of access equipment, but only the following four categories will be considered here: ➤ ➤ ➤ ➤

ladders ﬁxed scaffold prefabricated mobile scaffold towers mobile elevated work platforms.

➤

➤

Ladders The main cause of accidents involving ladders is ladder movement while in use. This occurs when they have not been secured to a ﬁxed point, particularly at the foot. Other causes include over-reaching by the worker, slipping on a rung, ladder defects and, in the case of metal ladders, contact with electricity. The main types of accident are falls from ladders. There are three common materials used in the construction of ladders – aluminium, timber and glass ﬁbre. Aluminium ladders have the advantage of being light but should not be used in high winds or near live electricity. Timber ladders need regular inspection for damage and should not be painted since this could hide cracks. Glass ﬁbre ladders can be used with near electrical equipment and in food processing areas. The following factors should be considered when using ladders: ➤ ensure that the use of a ladder is the safest means of access given the work to be done and the height to be climbed ➤ the location itself needs to be checked. The supporting wall and supporting ground surface should be dry and slip free. Extra care will be needed if the area is busy with pedestrians or vehicles ➤ the ladder needs to be stable in use. This means that the inclination should be as near the optimum as possible (1 in 4 ratio of distance from the wall to distance up the wall). The foot of the ladder should be tied to a rigid support. Weather conditions must be suitable (no high winds or heavy rain). The proximity of live electricity should also be checked. (This last point is important when ladders are to be carried beneath power lines) ➤ there should be at least 1 m of ladder above the stepping off point ➤ the work activity must be considered in some detail. Over-reaching must be eliminated and consideration given to the storage of paints or tools which are to be used from the ladder and any loads to be carried

292

➤

up the ladder. The ladder must be matched to work required workers who are to use ladders must be trained in the correct method of use and selection. Such training should include the use of both hands during climbing, clean non-slippery footwear, clean rungs and an undamaged ladder ladders should be inspected (particularly for damaged or missing rungs) and maintained on a regular basis and they should only be repaired by competent persons the transportation and storage of ladders is important since much damage can occur at these times. They need to be handled carefully and stored in a dry place when a ladder is left secured to a structure during non-working hours, a plank should be tied to the rungs to prevent unauthorized access to the structure.

Certain work should not be attempted using ladders. This includes work where: ➤ ➤ ➤ ➤ ➤ ➤

a secure hand hold is not available the work is at an excessive height where the ladder cannot be secured or made stable the work is of long duration the work area is very large the equipment or materials to be used are heavy or bulky ➤ the weather conditions are adverse ➤ there is no protection from passing vehicles. There have been several rumours that the Work at Height Regulations have banned the use of ladders. This is not true. Ladders may be used for access and it is legal to work from ladders. Ladders may be used when a risk assessment shows that the risk of injury is low and the task is of short duration or there are unalterable features of the work site and that it is not reasonably practicable to use potentially safer alternative means of access. More information on ladders and their use within the requirements of the Work at Height Regulations is available from the British Ladder Manufacturers’ Association. Ladders for industrial work in the UK should be marked to: ➤ Timber BS1129: Kite marked Class 1 Industrial ➤ Aluminium BS2037: 1994 Kite Marked Class 1 Industrial ➤ Glass ﬁbre BSEN131: 1993 Kite marked Industrial ➤ Step stools BS7377: 1994.

Stepladders, trestles and staging Many of the points discussed for ladders apply to step ladders and trestles, where stability and over-reaching are the main hazards.

Construction activities – hazards and control Right way

Wrong Way

Stepladder too short

Steps at right height

Hazard overhead

No need to over-reach

Over-reaching up and sideways

Good grip on handrail

No grip on ladder

Working front-on

Sideways-on to work

Wearing good flat shoes

Foot on handrail

Clean undamaged steps

Wearing slippers

Firm level base

Loose tools on ladder

Undamaged stiles

Slippery and damaged steps

Rubber non-slip feet all in position

Uneven soft ground

Meets British or European standards

Damaged stiles Non-slip rubber foot missing

Figure 16.5

Working with Stepladders.

All equipment must be checked by the supervisor before use to ensure that there are no defects and must be checked at least weekly whilst in use on site. If a defect is noted, or the equipment is damaged, it must be taken out of use immediately. Any repairs must only be carried out by competent persons. Supervisors must also check that the equipment is being used correctly and not being used where a safer method should be provided. Where staging, such as a ‘Youngmans’ staging platform, is being used in roof areas, supervisors must ensure that only experienced operatives are permitted to carry out this work and that all necessary safety harnesses and anchorage points are provided and used. The main hazards associated with stepladders, trestles and staging are: ➤ unsuitable base (uneven or loose materials) ➤ unsafe and incorrect use of equipment (e.g. the use of staging for barrow ramps) ➤ overloading ➤ use of equipment where a safer method should be provided ➤ overhang of boards or staging at supports (‘trap ends’) ➤ use of defective equipment. Stepladders and trestles must be: ➤ manufactured to a recognized industrial speciﬁcation ➤ stored and handled with care to prevent damage and deterioration

➤ subject to a programme of regular inspection (there should be a marking, coding or tagging system to conﬁrm that the inspection has taken place) ➤ checked by the user before use ➤ taken out of use if damaged – and destroyed or repaired; ➤ used on a secure surface, and with due regard to ensuring stability at all times ➤ kept away from overhead cables and similar hazards. The small platform ﬁtted at the top of many stepladders is designed to support tools, paint pots and other working materials. It should not be used as a working place unless the stepladder has been constructed with a suitable handhold above the platform. Stepladders must not be used if they are too short for the work being undertaken, or if there is not enough space to open them out fully. Platforms based on trestles should be fully boarded, adequately supported (at least one support for each 1.5 m of board for standard scaffold boards) and provided with edge protection when there is a risk of falling a distance liable to cause injury.

Fixed scaffolds It is quicker and easier to use a ladder as a means of access, but it is not always the safest. Jobs, such as painting, gutter repair, demolition work or window replacement, are often easier done using a scaffold. Unless the work can be completed comfortably using ladders, then a scaffold should be considered. Scaffolds must be capable of supporting building workers, equipment, materials,

293

Introduction to Health and Safety at Work (a) Bay l length h

Toe board

Transoms fixed with putlog or right angle couplers

Guardrails fixed to the standards

Ledgers fixed to standards with right angle couplers

Joint pin or sleeve coupler

Reveal tie tube wedged into opening with reveal Longitudinal or pin and fixed with right facade bracing angle couplers Longitudinal bracing in zig zag pattern

tools and any accumulated waste. A common cause of scaffold collapse is the ‘borrowing’ of boards and tubes from the scaffold, thus weakening it. Falls from scaffolds are often caused by badly constructed working platforms, inadequate guardrails or climbing up the outside of a scaffold. Falls also occur during the assembly or dismantling process. There are two basic types of external scaffold:

Ledger bracing at right angles to building 38 225 mm timber sole plates when standing on soil

(b)

➤ independent tied – these are scaffolding structures which are independent of the building but tied to it often using a window or window recess. This is the most common form of scaffolding ➤ putlog – this form of scaffolding is usually used during the construction of a building. A putlog is a scaffold tube which spans horizontally from the scaffold into the building – the end of the tube is ﬂattened and is usually positioned between two brick courses. The important components of a scaffold have been deﬁned in a guidance note issued by the HSE as follows (Figure 16.6(a)). Standard an upright tube or pole used as a vertical support in a scaffold. Ledger a tube spanning horizontally and tying standards longitudinally. Transom a tube spanning across ledgers to tie a scaffold transversely. It may also support a working platform. Bracing tubes which span diagonally to strengthenand prevent movement of the scaffold.

294

Figure 16.6 (a) Typical independent tied scaffold. (b) fixed scaffold left in place to fit the gutters.

Guardrail a horizontal tube ﬁtted to standards along working platforms to prevent persons from falling. Toe boards these are ﬁtted at the base of working platforms to prevent persons, materials or tools falling from the scaffold.

Construction activities – hazards and control The following factors must be addressed if a scaffold is being considered for use for construction purposes: ➤ scaffolding must only be erected by competent people who have attended recognized training courses. Any work carried out on the scaffold must be supervised by a competent person. Any changes to the scaffold must be done by a competent person ➤ adequate toe boards, guardrails and intermediate rails must be ﬁtted to prevent people or materials from falling ➤ the scaffold must rest on a stable surface, uprights should have base plates and timber sole plates if necessary ➤ the scaffold must have safe access and egress ➤ work platforms should be fully boarded with no tipping or tripping hazards ➤ the scaffold should be sited away from or protected from trafﬁc routes so that it is not damaged by vehicles ➤ lower level uprights should be prominently marked in red and white stripes ➤ the scaffold should be properly braced, secured to the building or structure ➤ overloading of the scaffold must be avoided ➤ the public must be protected at all stages of the work ➤ regular inspections of the scaffold must be made and recorded.

Prefabricated mobile scaffold towers Mobile scaffold towers are frequently used throughout industry. It is essential that the workers are trained in their use since recent research has revealed that 75% of lightweight mobile prefabricated tower scaffolding is either erected, used, moved or dismantled in an unsafe manner (Figure 16.7). The following points must be considered when mobile scaffold towers are to be used:

➤ the selection, erection and dismantling of mobile scaffold towers must be undertaken by competent and trained persons with maximum height to base ratios not being exceeded ➤ diagonal bracing and stabilizers should always be used ➤ access ladders must be ﬁtted to the narrowest side of the tower or inside the tower and persons should not climb up the frame of the tower ➤ all wheels must be locked while work is in progress and all persons must vacate the tower before it is moved ➤ the tower working platform must be boarded, ﬁtted with guardrails and toe boards and not overloaded ➤ towers must be tied to a rigid structure if exposed to windy weather or to be used for work such as jet blasting

Boarding and toe boards

Internal ladders

Cross bracing

Outriggers

Locking wheels

Figure 16.7

Typical prefabricated tower scaffold.

295

Introduction to Health and Safety at Work ➤ persons working from a tower must not over-reach or use ladders from the work platform ➤ safe distances must be maintained between the tower and overhead power lines both during working operations and when the tower is moved ➤ the tower should be inspected on a regular basis and a report made.

Mobile elevated work platforms Mobile elevated work platforms are very suitable for high level work such as changing light bulbs in a warehouse. The following factors must be considered when using mobile elevated work platforms: ➤ the mobile elevated work platform must only be operated by trained and competent persons ➤ it must never be moved in the elevated position ➤ it must be operated on level and stable ground with consideration being given for the stability and loading of ﬂoors ➤ the tyres must be properly inﬂated and the wheels immobilized ➤ outriggers should be fully extended and locked in position ➤ due care must be exercised with overhead power supplies obstructions and adverse weather conditions ➤ warning signs should be displayed and barriers erected to avoid collisions

➤ it should be maintained regularly and procedures should be in place in the event of machine failure; and ➤ drivers of MEWPs must be instructed in emergency procedures particularly to cover instances of power failure. When working on a MEWP, there is a danger that the operator may become trapped against an overhead or adjacent object and preventing him from releasing the controls. There have also been accidents caused when a MEWP is reversed into areas where there is poor pedestrian segregation and the driver has limited visibility. During any manoeuvring operation, a dedicated banksman should be used.

16.5.3

Inspection and maintenance

Inspection Equipment for work at height needs regular inspection to ensure that it is ﬁt for use. A marking system is probably required to show when the next inspection is due. Formal inspections should not be a substitute for any pre-use checks or routine maintenance. Inspection does not necessarily cover the checks that are made during maintenance although there may be some common features. Inspections need to be recorded but checks do not. Under the Work at Height Regulations weekly inspections are still required for scaffolding used in construction, as required by the Construction (Design and Management) Regulations where a person could fall 2 m or more. The requirements for inspection are set out in to the regulations as follows: ➤ The name and address of the person for whom the inspection was carried out ➤ The location of the work equipment inspected ➤ A description of the work equipment inspected ➤ The date and time of the inspection ➤ Details of any matter identiﬁed that could give rise to a risk to the health or safety of any person ➤ Details of any action taken as a result of any matter identiﬁed in paragraph 5 ➤ Details of any further action considered necessary ➤ The name and position of the person making the report. Appendix 16.1 shows the inspection format under the CDM Regulations which still covers the essential items under the Work at Height Regulations and has been slightly adapted to suit.

Maintenance Figure 16.8 Mobile elevating work platform – one type of a wide range.

296

Inspections and even thorough examinations are not substitutes for properly maintaining equipment. The information gained in the maintenance work, inspections

Construction activities – hazards and control and thorough technical examinations should inform one another. A maintenance log should be kept and be up to date. The whole maintenance system will require proper management systems. The frequency will depend on the equipment, the conditions in which it is used and the manufacturers’ instructions.

16.6 Excavations 16.6.1

➤ contact with underground services ➤ access and egress to the excavation ➤ fumes, lack of oxygen and other health hazards (such as Weil’s disease). Clearly, alongside these speciﬁc hazards, more general hazards, such as manual handling, electricity, noise and vibrations, will also be present.

16.6.2

Precautions and controls required for excavations

Hazards associated with excavations

There are about seven deaths each year due to work in excavations. Many types of soil, such as clays, are selfsupporting but others, such as sands and gravel, are not. Many excavations collapse without any warning resulting in death or serious injury. Many such accidents occur in shallow workings. It is important to note that, although most of these accidents affect workers, members of the public can also be injured. The speciﬁc hazards associated with excavations are as follows: ➤ ➤ ➤ ➤ ➤ ➤

collapse of the sides materials falling on workers in the excavation falls of people and/or vehicles into the excavation workers being struck by plant specialist equipment such as pneumatic drills hazardous substances particularly near the site of current or former industrial processes ➤ inﬂux of ground or surface water and entrapment in silt or mud ➤ proximity of stored materials, waste materials or plant ➤ proximity of adjacent buildings or structures and their stability

Figure 16.9 Timbered excavation with ladder access and supported services (guard removed on one side for clarity).

The following precautions and controls should be adopted: ➤ at all stages of the excavation, a competent person must supervise the work and the workers given clear instructions on working safely in the excavation ➤ the sides of the excavation must be prevented from collapsing either by digging them at a safe angle (between 5º and 45º dependent on soil and dryness) or by shoring them up with timber, sheeting or a proprietary support system. Falls of material into the workings can also be prevented by not storing spoil material near the top of the excavation ➤ the workers should wear hard hats ➤ if the excavation is more than 2 m deep, a substantial barrier, consisting of guardrails and toe boards should be provided around the surface of the workings ➤ vehicles should be kept away as far as possible using warning signs and barriers. Where a vehicle is tipping materials into the excavation, stop blocks should be placed behind its wheels ➤ it is very important that the excavation site is well lit at night ➤ all plant and equipment operators must be competent and non-operators should be kept away from moving plant ➤ personal protective equipment must be worn by operators of noisy plant ➤ nearby structures and buildings may need to be shored up if the excavation may reduce their stability. Scaffolding could also be de-stabilized by adjacent excavation trenches ➤ the inﬂux of water can only be controlled by the use of pumps after the water has been channelled into sumps. The risk of ﬂooding can be reduced by the isolation of the mains water supply. ➤ the presence of hazardous substances or health hazards should become apparent during the original survey work and, when possible, removed or suitable control measures adopted. Any such hazards found after work has started, must be reported and noted in the inspection report and remedial measures taken. Exhaust fumes can be dangerous and petrol

297

Introduction to Health and Safety at Work or diesel plant should not be sited near the top of the excavation ➤ the presence of buried services is one of the biggest hazards and the position of such services must be ascertained using all available service location drawings before work commences. Since these will probably not be accurate, service location equipment should be used by speciﬁcally trained people. Only hand tools should be used in the vicinity of underground services. Overhead services may also present risks to cranes and other tall equipment ➤ safe access by ladders is essential, as are crossing points for pedestrians and vehicles. Whenever possible, the workings should be completely covered outside working hours, particularly if there is a possibility of children entering the site ➤ ﬁnally, care is needed during the ﬁlling in process.

16.6.3

Inspection and reporting requirements

The duty to inspect and prepare a report only applies to excavations which need to be supported to prevent accidental fall of material. Only persons with a recognized and relevant competence should carry out the inspection and write the report. Inspections should take place at the following timing and frequency: ➤ after any event likely to affect the strength or stability of the excavation ➤ before work at the start of every shift ➤ after an accidental fall of any material. Although an inspection must be made at the start of every shift, only one report is required of such inspections every seven days. However, reports must be completed following all other inspections. The report should be completed before the end of the relevant working period and a copy given to the manager responsible for the excavation within 24 hours. The report must be kept on site until the work is completed and then retained for 3 months at an ofﬁce of the organization which carried out the work. A suitable form is shown in the Appendix to this chapter.

16.7 Practice NEBOSH questions for Chapter 16 1. Outline a hierarchy of measures to be considered when a construction worker is likely to fall while working at height. 2. Outline EIGHT precautions that should be considered to prevent accidents to children who might

298

be tempted to gain access to a construction site. 3. A contractor has been engaged to undertake building maintenance work in a busy warehouse. Outline the issues that should be covered in an induction programme for the contractor’s employees. 4. The exterior paintwork of a row of shops in a busy high street is due to be repainted. Identify the hazards associated with the work and outline the corresponding precautions to be taken. 5. Outline the precautions to be taken when carrying out repairs to the ﬂat roof of a building. 6. Outline the precautions to be taken when repair work is to be carried out on the sloping roof of a building. 7. Outline the precautions to be taken to ensure the safety of workers required to undertake repair work on a fragile roof. 8. (a) Explain the meaning of the term ‘hazard’ (b) Outline the main hazards that may be present during the demolition of a multi-storey building. 9. (a) Outline the possible causes of a dumper truck overturn on a construction site (b) Identify the design features of a dumper truck intended to minimize the risk of, or severity of injury from, an overturn. 10. A manufacturing company is to relocate to premises that require refurbishment before equipment and staff can be moved. Outline the sanitary and washing facilities that should be considered when planning the refurbishment. 11. Outline the health and safety requirements relating to the provision of welfare, ﬁre prevention and ﬁrstaid facilities on construction sites. 12. (a) Outline the main duties of a CDM coordinator under the Construction (Design and Management) Regulations (a) Identify FOUR items of information in the health and safety ﬁle for an existing building that might be needed by a contractor carrying out refurbishment work. 13. With reference to the Construction (Design and Management) Regulations: (i) Identify the circumstances under which a construction project must be notiﬁed to an enforcing authority

Construction activities – hazards and control (ii) Outline the duties of the client under the Regulations.

(i) Identify the potential hazards associated with the task (ii) Outline the measures to be taken to ensure the safety of the maintenance workers and others who may be affected by the work.

14. Outline FOUR duties of each of the following persons under the Construction (Design and Management) Regulations: (i) the CDM coordinator (ii) the principal contractor.

25. Identify the main hazards associated with excavation work on construction sites.

15. Explain the issues that would need to be addressed if work is to be carried out safely from a ladder.

26. Outline the main precautions to be taken when carrying out excavation work.

16. Outline the main dangers and the corresponding precautions that should be taken with the use of ladders.

27. The water main supplying a school is to be replaced. The work will be carried out in a 1.5 metre deep excavation, which will be supported in order to ensure the safety of the employees working in the excavation. (i) Identify when the THREE statutory inspections of the supported excavation must be carried out by the competent person (ii) State the information that should be recorded in the excavation inspection report (iii) Other that the provision of supports for the excavation, outline additional precautions to be taken during the repair work in order to reduce the risk of injury to the employees and others who may be affected by the work.

17. Identify the ways in which accidents may be prevented when using ladders as a means of access. 18. Outline the precautions that might be taken in order to reduce the risk of injury when using stepladders. 19. Outline THREE causes of a scaffold collapse. 20. Mobile tower scaffolds should be used on stable, level ground. List EIGHT additional points that should be considered to ensure safe use of a mobile tower scaffold. 21. Identify measures that should be adopted in order to protect against the dangers of people and/or materials falling from a mobile tower scaffold. 22. Give reasons that may cause a mobile tower scaffold to become unstable. 23. Outline the precautions to be taken when using a mobile elevating platform (MEWP) to reach a high point such as a streetlight. 24. Fluorescent tubes in the roof space of a busy warehouse are to be replaced by maintenance workers using a mobile elevating working platform (MEWP).

28. Identify EIGHT possible health hazards to which construction workers may be exposed AND in EACH case give an example of a likely source. 29. (a) Identify FOUR possible ill-health effects that can be caused from working with cement (b) Outline ways in which the ill-health effects in (a) can be prevented. 30. (a) Identify the three types of asbestos commonly found in buildings (b) Explain where asbestos is likely to be encountered in a building during renovation work.

299

Introduction to Health and Safety at Work Appendix 16.1

Inspection report

Report of results of every inspection made in pursuance of Construction (Design and Management) Regulations 2007 or the Work at Height Regulations 2005) 1. Name and address of person for whom inspection was carried out.

2. Site address

3. Date and time of inspection.

4. Location and description of workplace (including any plant, equipment or materials) inspected.

5. Matters which give rise to any health and safety risks.

6. Can work be carried out safely? 7. If not, name of person informed.

8. Details of any other action taken as a result of matters identiﬁed in 5 above.

9. Details of any further action considered necessary.

10. Name and position of person making the report. 11. Date report handed over.

300

Y/N

Construction activities – hazards and control Inspection reports: Notes

Place of work requiring inspection

Any working platform or part thereof any personal suspension equipment.

Timing and frequency of inspection Before being used for the ﬁrst time.

After substantial addition, dismantling or alteration.

After any event likely to have affected its strength or stability.

At regular intervals not exceeding 7 days.

✓

✓

✓

✓

Before work at the start of every shift.

After accidental fall of rock, earth or any material.

✓

Excavations which are supported in pursuit of paragraphs (1), (2) or (3) of regulation 12 of construction regs.

✓

✓

Cofferdams and caissons.

✓

✓

NOTES General 1. The inspection report should be completed before the end of the relevant working period. 2. The person who prepares the report should, within 24 hours, provide either the report or a copy to the person on whose behalf the inspection was carried out. 3. The report should be kept on site until work is complete. It should then be retained for three months at an ofﬁce of the person for whom the inspection was carried out. Working platforms only 1. An inspection is only required where a person is liable to fall more than 2 metres from a place of work. 2. Any employer or any other person who controls the activities of persons using a scaffold shall ensure that it is stable and of sound construction and that the relevant safeguards are in place before his employees or persons under his control ﬁrst use the scaffold. 3. No report is required following the inspection of any mobile tower scaffold which remains in the same place for less than 7 days. 4. Where an inspection of a working platform or part thereof or any personal suspension equipment is carried out: i. before it is taken into use for the ﬁrst time; or ii. after any substantial addition, dismantling or other alteration; not more than one report is required for any 24 hour period. Excavations only 1. The duties to inspect and prepare a report apply only to any excavation which needs to be supported to prevent any person being trapped or buried by an accidental collapse, fall or dislodgement of material from its sides, roof or area adjacent to it. Although an excavation must be inspected at the start of every shift, only one report of such inspections is required every 7 days. Reports must be completed for all inspections carried out during this period for other purposes, e.g. after accidental fall of material.

301

Footings

Standards

Ledgers

Bracing

Putlogs and transoms

Couplings

Bridles

Ties

Boarding

Guard rails and toe boards

Ladders

Soft and uneven

Not plumb

Not level

Some missing

Wrongly spaced

Wrong ﬁtting

Wrong spacing

Some missing

Bad boards

Wrong height

Damaged

No base plates

Jointed at same height

Joints in same bay

Loose

Loose

Loose

Wrong couplings

Loose

Trap boards

Loose

Insufﬁcient length

No sole plates

Wrong spacing

Loose

Wrong ﬁttings

Wrongly supported

Damaged

No check couplers

Not enough

Incomplete

Some missing

Not tied

Undermined

Damaged

Damaged

No check couplers

Insufﬁcient supports

Introduction to Health and Safety at Work

302 Checklist of typical scaffolding faults

Construction activities – hazards and control Appendix 16.2 CDM 2007

Summary of proposed application and notification under

303

Introduction to Health and Safety at Work Appendix 16.3

Pre-Construction information

This is taken from Appendix 2 of the ACOP Managing Health and Safety in construction, L144 When drawing up the pre-construction information, each of the following topics should be considered. Information should be included where the topics is relevant to the work proposed. The preconstruction information provides information for those bidding for or planning work, and for the development of the construction phase plan. The level of detail in the information should be proportionate to the risks involved in the project.

Pre-construction information 1.

2.

304

Description of project (a) Project description and programme details including: ➤ key dates (including planned start and ﬁnish of the construction phase), and ➤ the minimum time to be allowed between appointment of the principal contractor and instruction to commence work on site. (b) Details of client, designers, CDM co-ordinator and other consultants (c) Whether or not the structure will be used as a workplace – in which case, the ﬁnished design will need to take account of the relevant requirements of the Workplace (Health, Safety and Welfare) Regulations (d) Extent and location of existing records and plans. Client’s considerations and management requirements (a) Arrangements for: ➤ planning for and managing the construction work, including any health and safety goals for the project ➤ communications and liaison between client and others ➤ security of the site ➤ welfare provisions. (b) Requirements relating to the health and safety of the client’s employees or customers or those involved in the project such as: ➤ site hoarding requirements ➤ site transport arrangements or vehicle movement restrictions

3.

➤ client permit-to-work systems ➤ ﬁre precautions ➤ emergency procedures and means of escape ➤ ‘no-go’ areas or other authorizations requirements for those involved in the project ➤ any areas the client has designated as conﬁned spaces ➤ smoking and parking restrictions. Environmental restrictions and existing on-site risks (a) Safety hazards, including: ➤ boundaries and access, including temporary access, e.g. narrow streets, lack of parking, turning or storage ➤ any restrictions on deliveries or waste collection or storage ➤ adjacent land uses, e.g. schools, railway lines or busy roads ➤ existing storage of hazardous materials ➤ location of existing services particularly those that are concealed – water, electricity, gas etc. ➤ ground conditions, underground structures or water courses where these might effect the safe use of plant, e.g. cranes, or the safety of ground work ➤ information about existing structures – stability, structural form, fragile or hazardous materials, anchorage points for fall arrest systems (particularly where demolition is involved) ➤ previous structural modiﬁcations, including weakening or strengthening of the structure (particularly where demolition is involved) ➤ ﬁre damage, ground shrinkage, movement or poor maintenance which may have adversely affected the structure ➤ any difﬁculties relating to plant and equipment in the premises, such as overhead gantries whose height restrict access ➤ health and safety information contained in earlier design, construction or ‘as-built’ drawings, such as details of pre-stressed or post-tensioned structures.

Construction activities – hazards and control

4.

(b) Health hazards, including: ➤ asbestos, including results of surveys (particularly where demolition is involved) ➤ existing storage of hazardous material ➤ contaminated land, including results of surveys ➤ existing structures containing hazardous materials ➤ health risks arising from client’s activities. Significant design and construction hazards (a) Signiﬁcant design assumptions and suggested work methods, sequences or other control measures

Appendix 16.4

5.

Description of its format and any conditions relating to its content.

Construction Phase Plan

This is taken from Appendix 3 of the ACOP Managing health and safety in construction, L144. When drawing up the construction phase plan, employers should consider each of the following topics: information should be included in the plan where the topic is relevant to the work proposed; the plan sets out how health and safety is to be managed during the construction phase. The level of detail should be proportionate to the risks involved in the project.

Construction phase plan 1.

2.

(b) Arrangements for co-ordination of on-going design work and handling design changes (c) Information on signiﬁcant risks identiﬁed during design (d) Materials requiring particular precautions. The health and safety file

Description of project (a) Project description and programme details including key dates (b) Details of client, CDM co-ordinator, designers, principal contractor and other consultants (c) Extent and location of existing records and plans that are relevant to health and safety on site, including information about existing structures when appropriate. Management of the work (a) Management structure and responsibilities (b) Health and safety goals for the project and arrangements for monitoring and review of health and safety performance. (c) Arrangements for: ➤ regular liaisons between parties on site ➤ consultation with the workforce ➤ exchange of design information between the client, designers, CDM co-ordinator and contractors on site ➤ handling design changes during the project

3.

➤ the selection and control of contractors ➤ the exchange of health and safety information between contractors ➤ site security ➤ site induction ➤ on site training ➤ welfare facilities and ﬁrst aid ➤ the reporting and investigation of accidents and incidents including near misses ➤ the production and approval of risk assessments and written systems of work ➤ site rules ➤ ﬁre and emergency arrangements. Arrangements for controlling significant site risks (a) Safety risks, including: ➤ delivery and removal of materials (including waste) and work equipment taking account of any risks to the public, e.g. during access to and egress from the site ➤ dealing with services – water, electricity and gas, including overhead powerlines and temporary electrical installations ➤ accommodating adjacent land use ➤ stability of structures whilst carrying out construction work, including temporary structures and existing unstable structures ➤ preventing falls ➤ work with or near fragile materials ➤ control of lifting operations ➤ the maintenance of plant and equipment

305

Introduction to Health and Safety at Work ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤ ➤

306

work on excavations and work where there are poor ground conditions work on well, underground earthworks and tunnels work on or near water where there is a risk of drowning work involving diving work in a caisson or compressed air working work involving explosives trafﬁc routes and segregation of vehicles and pedestrians storage of materials (particularly hazardous materials) and work equipment any other signiﬁcant safety risks.

4.

(b) health risks, including: ➤ the removal of asbestos ➤ dealing with contaminated land ➤ manual handling ➤ use of hazardous substances, particularly where there is a need for health monitoring ➤ reducing noise and vibration ➤ working with ionizing radiation; any other signiﬁcant health risks. The health and safety ﬁle (a) Layout and format (b) Arrangements for the collation and gathering of information (c) Storage of information.

Summary of the main legal requirements 17.1 Introduction The achievement of an understanding of the basic legal requirements can be a daunting task. However, the health and safety student should not despair because at NEBOSH National Certiﬁcate level they do not need to know the full history of UK health and safety legislation, the complete range of regulations made under the Health and Safety at Work Act 1974 or the details of the appropriate European Directives. These summaries, which are correct up to the 1 March 2006, cover those Acts and Regulations which are required for the Certiﬁcate student and will provide the essential foundation of knowledge. They will also cover the requirements for similar awards at Certiﬁcate level, like the British Safety Council’s Certiﬁcate in Occupational Safety and Health, and below this level, like the IOSH Managing Safely Award. Students should check the latest edition of the NEBOSH Certiﬁcate guide to ensure that the regulations summarized here are the latest for the course being undertaken. Many managers will ﬁnd these summaries a useful quick reference to health and safety legal requirements. However, anyone involved in achieving compliance with legal requirements should ensure they read the regulations themselves, any approved codes of practice and HSE guidance.

17.2 The legal framework 17.2.1

17

and also the duties that employees have to themselves and to each other. The term ‘so far as is reasonably practicable’ qualiﬁes the duties in the HSW Act. In other words, the degree of risk in a particular job or workplace needs to be balanced against the time, trouble, cost and physical difﬁculty of taking measures to avoid or reduce the risk. The law simply expects employers to behave in a way that demonstrates good management and common sense. They are required to look at what the hazards are and take sensible measures to tackle them. The Management of Health and Safety at Work Regulations 1999 (the Management Regulations) clariﬁes what employers are required to do to manage health and safety under the Health and Safety at Work Act. Like the Act, they apply to every work activity. The law requires every employer to carry out a risk assessment. If there are ﬁve or more employees in the workplace, the signiﬁcant ﬁndings of the risk assessment need to be recorded. In a place like an ofﬁce, risk assessment should be straightforward; but where there are serious hazards, such as those in a chemical plant, laboratory or an oil rig, it is likely to be more complicated. The Factories Act 1961 and The Ofﬁce Shops and Railway Premises Act of 1963, while still partly remaining on the Statute Book for most practical health and safety work can be ignored. However, strangely, the notiﬁcation to the authorities of premises which come within the deﬁnition of these two acts are carried out on Form 9 for factories, Form 10 for construction and OSR 1 for ofﬁce shop and railway premises.

General 17.2.2

The Health and Safety at Work etc. Act 1974 (HSW Act) is the foundation of British health and safety law. It describes the general duties that employers have towards their employees and to members of the public,

The relationship between the regulator and industry

The Health and Safety Commission (HSC) consults widely with those affected by its proposals.

307

Introduction to Health and Safety at Work The HSC/E work through:

17.3 List of Acts, Order and Regulations summarized

➤ the HSC’s Industry and Subject Advisory Committees, which have members drawn from the areas of work they cover, and focus on health and safety issues in particular industries (such as the textile industry, construction and education or areas such as toxic substances and genetic modiﬁcation) ➤ intermediaries, such as small ﬁrms’ organizations providing information and advice to employers and others with responsibilities under the HSW Act ➤ guidance to enforcers, both the Health and Safety Executive (HSE) inspectors and those of local authorities ➤ the day-to-day contact which inspectors have with people at work. The HSC consults with small ﬁrms through Small Firms Forums. It also seeks views in detail from representatives of small ﬁrms about the impact on them of proposed legislation. At the time of writing the HSC/HSE are considering merging into one body still called the HSE. A consultative document has been issued which is available on the www.hse.gov.uk.

17.3 List of Acts, Order and Regulations summarized The following Acts and Regulations are covered in this summary: ➤ The Health and Safety at Work etc. Act 1974 (HSW Act) ➤ The Environmental Protection Act 1990. By far the most important of these is the HSW Act. Most of the relevant regulations covering health and safety at work have been made under this Act since 1974. Those relevant to the Certiﬁcate student are listed here and summarized in this chapter. The ﬁrst list is alphabetical and some titles have been modiﬁed to allow an easier search. The second list is chronological with Statutory Instrument Numbers. The Regulatory Reform Fire Safety Order was made under the Regulatory Reform Act 2001, and the Hazardous Waste regulations under the Environmental Protection Act. The Regulations/Order covered are as follows.

17.3.1 Alphabetical list of regulations/order summarized ➤ Chemicals (Hazardous Information and Packaging for Supply) Regulations 2002 Plus 2005 amendments

308

➤ Conﬁned Spaces Regulations 1997 ➤ Construction (Design and Management) Regulations 2007 ➤ Construction (Head Protection) Regulations 1989 ➤ Control of Noise at Work Regulations 2005 ➤ Control of Substances Hazardous to Health Regulations 2002 and 2004 Amendment ➤ Control of Vibration at Work Regulations 2005 ➤ Dangerous Substances and Explosive Atmospheres Regulations 2002 ➤ Electricity at Work Regulations 1989 ➤ Employers Liability (Compulsory Insurance) Act 1969 and Regulations 1998 ➤ Fire (Scotland Act) 2005 ➤ Hazardous Waste (England and Wales) Regulations 2005 ➤ Health and Safety (First Aid) Regulations 1981 ➤ Health and Safety (Safety Signs and Signals) Regulations 1996 ➤ Health and Safety (Consultation with Employees) Regulations 1996 ➤ Health and Safety Display Screen Equipment Regulations 1992 ➤ Information for Employees Regulations 1989 ➤ Ionising Radiations Regulations 1999 ➤ Lifting Operations and Lifting Equipment Regulations 1998 ➤ Management of Health and Safety at Work Regulations ➤ Manual Handling Operations Regulations 1992 ➤ Personal Protective Equipment at Work Regulations 1992 ➤ Provision and Use of Work Equipment Regulations 1998 (except Part IV – Power Presses) ➤ Reporting of Injuries Diseases and Dangerous Occurrences Regulations 1995 ➤ Safety Representatives and Safety Committees Regulations 1977 ➤ Supply of Machinery (Safety) Regulations 1992 ➤ The Regulatory Reform (Fire Safety) Order 2004 ➤ Workplace (Health, Safety and Welfare) Regulations 1992 ➤ Work at Height Regulations 2005. The following Acts and Regulations have also been included even though they are not in the NEBOSH General Certiﬁcate syllabus. Very brief summaries only are given: Asbestos at Work Regulations 2006 Control of Lead at Work Regulations 2002 Disability Discrimination Act 1995 and 2005 Electrical Equipment (Safety) Regulations 1994 Gas Appliances (Safety) Regulations 1992 Gas Safety (Installation and Use) Regulations 1998

Summary of the main legal requirements Occupiers Liability Acts 1957 and 1984 Pesticides Regulations 1986 Pressure Systems Safety Regulations 2000 Working Time Regulations 1998, 2001 and 2003.

2002

2677

2002

2776

2004

3386

17.3.2 Chronological list of Regulations/Orders summarized

2005 2005

735 1541

The list below gives the correct titles, year produced and Statutory Instrument number.

2005

1093

2005 2007

1643 3140

1981

0917

1989 1989

0635 0682

1989

2209

1992

2792

1992

2793

1992

2966

1992

3004

1992

3073

1995

3246

1996

0341

1996

1513

1997 1998

1713 2306

1998

2307

1998

2573

1999

437

1999 1999

3232 3242

2002

1689

Title Safety Representatives and Safety Committees Regulations Health and Safety (First Aid) Regulations Electricity at Work Regulations Health and Safety (Information for Employees) Regulations Construction (Head Protection) Regulations Health and Safety (Display Screen Equipment) Regulations Manual Handling Operations Regulations Personal Protective Equipment at Work Regulations Workplace (Health, Safety and Welfare) Regulations Supply of Machinery (Safety) Regulations Reporting of Injuries Diseases and Dangerous Occurrences Regulations Health and Safety (Safety Signs and Signals) Regulations Health and Safety (Consultation with Employees) Regulations Conﬁned Spaces Regulations Provision and Use of Work Equipment Regulations (except Part IV – Power Presses) Lifting Operations and Lifting Equipment Regulations Employers Liability (Compulsory Insurance) Regulations Control of Substances Hazardous to Health Regulations Ionising Radiations Regulations Management of Health and Safety at Work Regulations Chemicals (Hazardous Information and Packaging for Supply) Regulations

Very brief summaries only for 1957 and Ch 31 1984 1986 1992 1998

Ch 3 1510 0711 2451

1994

3260

1998 2000 2002

1833 128 2676

2003

1684

2005 2006

2739

Occupiers Liability Acts Control of Pesticides Regulations Gas Appliances (Safety) Regulations Gas Safety (Installation and Use) Regulations Electrical Equipment (Safety) Regulations Working Time Regulations Pressure Systems Safety Regulations The Control of Lead at Work Regulations Working Time (Amendment) Regulations Disability Discrimination Act 1995 and 2005 Control of Asbestos Regulations 2006

17.4 Health and Safety at Work etc. Act (HSW Act) 1974 The HSW Act was introduced to provide a comprehensive and integrated piece of legislation dealing with the health and safety of people at work and the protection of the public from work activities. A small amount of pre1974 legislation is still in place despite strenuous efforts to repeal and replace it with updated legislation under the HSW Act. The Act imposes a duty of care on everyone at work related to their roles. This includes employers, employees, owners, occupiers, designers, suppliers and manufacturers of articles and substances for use at work. It also

309

Health and Safety at Work etc. Act (HSW Act) 1974

SI no 0500

17.4

Year 1977

Control of Substances Hazardous to Health Regulations Dangerous Substances and Explosive Atmospheres Regulations Control of Substances Hazardous to Health (Amendment) Regulations Work at Height Regulations The Regulatory Reform (Fire Safety) Order Control of Vibration at Work Regulations Control of Noise at Work Regulations Construction Design and Management) Regulations

Introduction to Health and Safety at Work includes self-employed people. The detailed requirements are spelt out in Regulations. The Act basically consists of four parts: PART 1 covers: ➤ the health and safety of people at work ➤ protection of other people affected by work activities ➤ the control of risks to health and safety from articles and substances used at work PART 2: sets up the Employment Medical Advisory Service. PART 3: makes amendments to the safety aspects of building regulations. PART 4: general and miscellaneous provisions.

17.4.1

Duties of owners/occupiers, Sections 3 and 5

Every employer and self-employed person is under a duty to conduct their undertaking in such a way as to ensure, so far as is reasonably practicable, that persons not in their employment (and themselves for selfemployed) who may be affected, are not exposed to risks to their health and safety. Those in control of non-domestic premises have a duty to ensure, so far as is reasonably practicable, that the premises, the means of access and exit, and any plant or substances are safe and without risks to health. The common parts of residential premises are non-domestic. Section 5 was repealed by the Environmental Protection Act 1990.

Duties of employers – Section 2

The employers’ main general duties are to ensure, so far as is reasonably practicable, the health, safety and welfare at work of all their employees, in particular: ➤ the provision of safe plant and systems of work ➤ the safe use, handling, storage and transport of articles and substances ➤ the provision of any required information, instruction, training and supervision ➤ a safe place of work including safe access and egress; and ➤ a safe working environment with adequate welfare facilities. When ﬁve or more people {The Employer’s health and safety Policy Statements (Exception) Regulations 1975 (SI No 1584) exempted an employer who employees less than 5 people} are employed the employer must: ➤ prepare a written general health and safety policy ➤ set down the organization and arrangements for putting that policy into effect ➤ revise and update the policy as necessary ➤ bring the policy and arrangements to the notice of all employees. Employers must also: ➤ consult safety representatives appointed by recognized trade unions* ➤ consult safety representatives elected by employees* ➤ establish a safety committee if requested to do so by recognized safety representatives*. *Note that these has been enacted by the Safety Representatives and Safety Committees Regulations 1977 and enhanced by the Health and Safety (Consultation with Employees) Regulations 1996 (see later summaries).

310

17.4.2

17.4.3

Duties of manufacturers/suppliers – Section 6

Persons who design, manufacture, import or supply any article or substance for use at work must ensure, so far as is reasonably practicable, that: ➤ they are safe and without risks to health when properly used (i.e. according to manufacturers’ instructions) ➤ carry out such tests or examinations as are necessary for the performance of their duties ➤ provide adequate information (including revisions) to perform their duties ➤ carry out any necessary research to discover, eliminate or minimize any risks to health or safety ➤ the installer or erector must ensure that nothing about the way in which the article is installed or erected makes it unsafe or a risk to health.

17.4.4

Duties of employees – Section 7

Two main duties are placed on employees: ➤ to take reasonable care for the health and safety of themselves and others who may be affected by their acts or omissions at work ➤ to co-operate with their employer and others to enable them to fulﬁll their legal obligations.

17.4.5

Other duties – Sections 8 and 9

No person may misuse or interfere with anything provided in the interest of health, safety or welfare in pursuance of any of the relevant statutory provisions. Employees cannot be charged for anything done, or provided, to comply with the relevant statutory provisions. For example employees cannot be charged

Summary of the main legal requirements for personal protective equipment required by a health and safety regulation.

17.4.6

Powers of inspectors – Sections 20 & 25

Inspectors appointed under this Act have the authorization to enter premises at any reasonable time (or anytime in a dangerous situation), and to: ➤ take a constable with them if necessary ➤ take with them another authorized person and necessary equipment ➤ examine and investigate ➤ require premises or anything in them to remain undisturbed for purposes of examination or investigation ➤ take measurements, photographs and recordings ➤ cause an article or substance to be dismantled or subjected to any test ➤ take possession of or retain anything for examination or legal proceedings ➤ take samples as long as a comparable sample is left behind ➤ require any person who can give information to answer questions and sign a statement. Evidence given under this Act cannot be used against that person or their spouse ➤ require information, facilities, records or assistance ➤ do anything else necessary to enable them to carry out their duties ➤ issue an Improvement Notice(s), which is a notice identifying a contravention of the law and specifying a date by which the situation is remedied. There is an appeal procedure which must be triggered within 21 days. The notice is suspended pending the outcome of the appeal ➤ issue a Prohibition Notice(s), which is a notice identifying and halting a situation which involves or will involve a risk of serious personal injury to which the relevant statutory provisions apply. A contravention need not have been committed. The notice can have immediate effect or be deferred, for example to allow a process to be shut down safely. Again there is provision to appeal against the notice but the order still stands until altered or rescinded by an Industrial tribunal ➤ initiate prosecutions ➤ seize, destroy or render harmless any article or substance which is a source of imminent danger.

17.4.7

Offences – Section 33

Offences prosecuted under the HSW Act or Regulations attract a maximum ﬁne of £5000 if tried on summary

conviction in a Lower Court (e.g. Magistrates Court). Exceptionally this is a maximum of £20 000 for breaches of Sections 2–6 (General duties) and £20 000 and/or 6 months imprisonment for contravening a prohibition notice, an improvement notice or remedy order of the court. A number of cases can also be tried on indictment, in a Higher Court (the Crown Court) where the ﬁnes are unlimited and the maximum prison sentence can be up to 2 years. However, prison sentences are limited to certain cases only. Table 17.1 summarizes the position. Note that offences relating to breaches of general health and safety requirements (shown in bold) do not attract a prison sentence. If a Regulation has been contravened, failure to comply with an approved code of practice is admissible in evidence as failure to comply. Where an offence is committed by a corporate body with the knowledge, connivance or neglect of a responsible person, both that person and the body. In proceedings the onus of proving the limits of what is reasonably practicable rests with the accused. On conviction of directors for indictable offences in connection with the management of a company, the courts may also make a disqualiﬁcation order. Lower court maximum Higher court maximum

17.4.8

5 years disqualiﬁcation 15 years disqualiﬁcation

The Health and Safety Commission/ Executive – Section 10

Section 10 of the Act establishes these two bodies whose chief functions are: ➤ The Health and Safety Commission (HSC) has the prime responsibility for administering the law and practice on occupational health and safety. Its nine members are appointed by the Government from industry, trade unions, local authorities and others. The HSC has wide powers to do anything (except borrow money) which is calculated to facilitate, or is conducive or incidental to, the performance of its functions. ➤ The Health and Safety Executive is the executive and enforcement arm of the HSC. The HSC may direct its work except where it involves enforcement of the law in individual cases. Enforcement of the law in certain premises like ofﬁces and shops is the responsibility of local authority environmental health departments, whose ofﬁcers have identical powers to HSE inspectors. ➤ Note that in December 2006 the HSC published a public consultation document seeking views on

311

Introduction to Health and Safety at Work Table 17.1

Offences and penalties under HSW Act

Offence

Summary conviction

Conviction on indictment

HSW Act s.33(1A) • breach of HSW Act ss. 2, 3, 4 or 6

Max. £20 000 ﬁne

Fine (unlimited)

HSW Act s.33(2) • obstructing an inspector, impersonating an inspector, contravening requirement of inspector under s.20, or similar

17.5

Environmental Protection Act 1990

HSW Act s.33(2A) • failure to comply with enforcement notice or court order

Max. £5000 ﬁne

Max. £20 000 and/or up to six months’ imprisonment

Fine (unlimited) and/or up to two years’ imprisonment

HSW Act s.33(3) • all other offences (except those specified in s.33(4)) • breach of HSW Act ss. 7, 8 or 9 • breach of Regulations made under the Act • making false statements or entries • using, or possessing a document with the intent to deceive

Max. £5000 ﬁne

Fine (unlimited)

HSW Act s.33(3) – offences specified in s.33(4) • operating without, or contravening the terms or conditions of, a licence when one is required (e.g. Under Asbestos (Licensing) Regulations 1983) • acquiring or attempting to acquire, possessing or using an explosive article or substance in contravention of the relevant statutory provisions • using or disclosing information in contravention of sections 27(4) and 28 (relates to information provided to HSC/E etc. by notice or under relevant statutory provisions)

Max. £5000 ﬁne

Fine (unlimited) and/or up to two years’ imprisonment

merging HSC and HSE into a single health and safety authority. ➤ HSC believes that merger with HSE will modernize their corporate governance and provide a stronger voice for health and safety. As part of this, the consultation discusses how the HSC would become the governing body of the new authority, retaining its current independence and links with stakeholders while strengthening its capacity to challenge and support delivery. The proposal recommends that the new body should retain the HSE name.

17.4.9

References

Health and Safety at Work etc. Act 1974, Chapter 37, London, The Stationery Ofﬁce An Introduction to Health and Safety: Guidance on a Health and Safety for small ﬁrms, INDG259 (rev1), reprinted 2006, HSE Books ISBN 0 7176 2685 7 The Health and Safety System in Great Britain, HSC, 2002 HSE Books ISBN 0 7176 2243 6

312

17.5 Environmental Protection Act 1990 17.5.1

Introduction

The Environmental Protection Act 1990 is still the centrepiece of current UK legislation on environmental protection. It is divided into nine parts, corresponding to the wide range of subjects dealt with by the Act. Integrated Pollution Control (IPC) was a system established by Part 1 of the Act. Part 1 introduced Part A Processes, which are the most potentially polluting or technologically complex processes. In England and Wales these are enforced by the Environment Agency. In Scotland there is a parallel system enforced by the Scottish Environment Protection Agency. Less polluting industries were classiﬁed as Part B, with only emissions released to air being subject to regulatory control. For such processes local authorities are the enforcing body and the system is known as Local Air Pollution Control (LAPC). Both IPC and LAPC have now been replaced by a Pollution Prevention and Control (IPPC) regime that

Summary of the main legal requirements

Box 17.1

Pollution Prevention and Control Regimes

IPC (regime A) Integrated Pollution Control LAPC (regime B) Local air Pollution Control

PPC REGIME Pollution Prevention and Control IPPC (regime A1 and A2) Integrated Pollution Prevention & Control LAPPC (regime B) Local air Pollution Prevention & Control

Under Environmental Protection Act 1990 Part 1

Under Pollution Prevention and Control Act 1999

Regime A – This is an integrated permitting regime. Emissions to the air, land and water of the potentially more polluting processes are regulated. The Environment Agency is the regulator.

Regime A1 – This is an integrated permitting regime. Emissions to the air, land and water of potentially more polluting processes are regulated. The Environment agency is the Regulator.

Regime B – This regime permits processes with a lesser potential for polluting emissions. Only emissions to the air are regulated. The Local Authority is the Regulator.

Regime A2 – This is an integrated permitting regime. Emissions to the air, land and water of processes with a lesser potential to pollute are regulated. The Local Authority agency is the regulator. Regime B – This is the permitting of processes with a lesser potential to pollute. Only emissions to the air are regulated. The Local Authority is the Regulator.

implements the requirements of the EC Directive 96/61 on integrated pollution prevention and control. This was introduced under the Pollution Prevention and Control Act of 1999 (1999 Chapter 24), which repealed Part 1 of the Environmental Protection Act. The change is outlined by Box 17.1.

17.5.2 Integrated Pollution Prevention and Control The system of Integrated Pollution Prevention and Control (IPPC) applies an integrated environmental approach to the regulation of certain industrial activities. This means that emissions to air, water (including discharges to sewer) and land, plus a range of other environmental effects, must be considered together. It also means that regulators must set permit conditions so as to achieve a high level of protection for the environment as a whole. These conditions are based on the use of the ‘Best Available Techniques’ (BAT), which balances the costs to the operator against the beneﬁts to the environment. IPPC aims to prevent emissions and waste production and where that is not practicable, reduce them to acceptable levels.

IPPC also takes the integrated approach beyond the initial task of permitting, through to the restoration of sites when industrial activities cease.

17.5.3

Setting the legal framework

The PPC Regulations implement the European Community (EC) Directive 96/61/EC on Integrated Pollution Prevention and Control (‘the IPPC Directive’), insofar as it relates to installations in England and Wales. Separate Regulations apply the IPPC Directive in Scotland and Northern Ireland and to the offshore oil and gas industries. ➤ Prior to the PPC Regulations coming into force, many industrial sectors covered by the IPPC Directive were regulated under Part I of the EPA 1990. This introduced the systems of Integrated Pollution Control (IPC), which controlled releases to all environmental media, and Local Air Pollution Control (LAPC), which controlled releases to air only. Other industrial sectors new to integrated permitting, such as the landﬁll, intensive farming and food and drink sectors were regulated, where appropriate, by separate waste management licences issued under Part II of the EPA

313

Introduction to Health and Safety at Work

➤

➤

➤

➤

and/or water discharge consents under the Water Resources Act 1991 or Water Industry Act 1991. The PPC Regulations create a coherent new framework to prevent and control pollution, with two parallel systems similar to the old regimes of IPC and LAPC. The ﬁrst of these – the ‘Part A’ regime of IPPC – applies a similar integrated approach to IPC while delivering the additional requirements of the IPPC Directive. ‘Part A’ extends the issues that regulators must consider alongside emissions into areas such as energy use and site restoration. The main provisions of IPPC apply equally to the ex-IPC processes and the other sectors new to integrated permitting. There are also some further requirements that apply solely to waste management activities falling under IPPC. The IPPC Directive applies to those landﬁlls receiving more than ten tonnes per day or with a total capacity exceeding 25 000 tonnes (but excluding landﬁlls taking only inert waste), the landﬁll directive applies to all landﬁlls. The PPC Regulations have been amended to include all landﬁlls. For landﬁlls the technical requirements are met through the Landﬁll Regulations. Defra issued separate guidance on the Landﬁll Regulations in 2004. The Environment Agency regulates Part A (1) installations. Part A (2) installations are regulated by the relevant local authority – usually the district, London or metropolitan borough council in England and the county or borough council in Wales. However, the local authority will always be a statutory consultee where the Environment Agency is the regulator, and vice versa. Moreover, the local authority and the Environment Agency will work together in the permitting process. Local authorities have expertise in setting standards for noise control, while the Environment Agency will ensure that permit conditions protect water adequately. Annex I describes how IPPC installations are classiﬁed into either Part A (1) or Part A (2) installations depending on what activities take place within them. The second new regime – the ‘Part B’ regime of Local Air Pollution Prevention and Control (LAPPC) – represents a continuation of the old LAPC regime. LAPPC is similar to IPPC from a procedural perspective, but it still focuses on controlling emissions to air only. Defra provides separate guidance on local authority air pollution control.

17.5.4

Overview of the regulatory process

The basic purpose of the IPPC regime is to introduce a more integrated approach to controlling pollution from industrial sources. It aims to achieve ‘a high level of protection of the environment taken as a whole by, in

314

particular, preventing or, where that is not practicable, reducing emissions into the air, water and land’ The main way of doing that is by determining and enforcing permit conditions based on BAT. ➤ The entire regulatory process for IPPC consists of a number of elements. These are outlined below. IPPC applies to speciﬁed ‘installations’ – both ‘existing’ and ‘new’ – requiring each ‘operator’ to obtain a permit from the regulator – either the Environment Agency or the local authority.

Stage 1 – Permitting 1.

2.

3. 4.

5.

The procedure begins with the preparation of an application by the operator. Once the regulator receives the application, they will consult various ‘statutory consultees’. Operators should be encouraged to engage the public at the earliest opportunity. Operators are required to advertise in one or more local papers and in the London Gazette details of the activity and its location together with a statement of where public representations should be made. After giving further public participation in the case of applications in respect of ‘new installations’, or ‘substantial changes’ to installations, the regulator will then determine the application, either granting a permit with conditions or refusing it. The Landﬁll Regulations required operators of all existing landﬁll sites to submit a conditioning plan (CP) by 16 July 2002 (if a site closed before 16 July 2002, then no plan was required). Otherwise the Environment Agency decides whether a landﬁll should continue operating on the basis of the conditioning plan. A PPC application building on the conditioning plan will then be required to be submitted by the date notiﬁed to the operator. In making an application the operator must cover various environmental issues. These include: The operator must also consider the condition of the site at the time of the original application. This will contribute to assessing the need for restoration when the installation closes (stage 3). In determining the application, the regulator must be satisﬁed that the operator has addressed the above points appropriately. It is therefore the operator’s responsibility to demonstrate that this is the case. ➤ Satisfactory environmental management of the installation and no signiﬁcant pollution is caused. ➤ Adequate compliance monitoring. ➤ Waste production is avoided and where waste is produced, it is recovered. Where that is not possible it is disposed of in a way producing the least impact on the environment, if any impact is produced at all.

Summary of the main legal requirements

Box 17.2 Best Available Techniques (BAT) This term is deﬁned as ‘the most effective and advanced stage in the development of activities and their methods of operation which indicates the practicable suitability of particular techniques for providing the basis for emission limit values designed to prevent, and where that is not practicable, generally to reduce the emissions and the impact on the environment as a whole’. This deﬁnition implies that BAT not only covers the technology used but also the way in which the installation is operated, to ensure a high level of environmental protection as a whole. BAT takes into account the balance between the costs and environmental beneﬁts (i.e. the greater the environmental damage that can be prevented, the greater the cost for the techniques).

➤ Assessment of polluting releases and the identiﬁcation of BAT (Best Available Techniques see Box 17.2 for a deﬁnition). ➤ Compliance with other EU directives, Community and national environmental quality standards (EQS,s) and domestic regulations. ➤ Energy is used efﬁciently. ➤ Measures are taken to avoid accidents and limit their consequences. ➤ Necessary measures are taken on the closure of an installation to avoid any pollution risk and return the site to a satisfactory condition. ➤ For landﬁlls, alternative requirements are speciﬁed by the Landﬁll Regulations.

Stage 2 – Operation 1.

2.

Once the regulator has issued a permit, the operator of an IPPC installation will have to carry out monitoring to demonstrate compliance with the permit conditions. Regulators will also carry out their own monitoring and inspections, and have a range of enforcement powers. Over time, regulators may vary permits to reﬂect changes in how installations are operated, or for other reasons. The regulator may vary permit conditions at either its own or the operator’s instigation, with the possibility of consultation in either case.

3.

The regulator may also transfer permits from one operator to another, for example when one operator is taken over by another. More generally, regulators must review permits periodically, or whenever circumstances make a review necessary, such as when signiﬁcant pollution occurs. Speciﬁc conditions may apply to individual installations that the regulator considers appropriate to ensure a high level of protection to the environment as a whole. If the regulator believes that the operator is breaching the conditions of a permit, enforcement options are available where: enforcement, suspension or a revocation notice can be served (the operator may appeal against this to the Secretary of State).

Stage 3 – Closure and Surrender When an installation closes, an operator should apply to surrender a permit, to end regulation under IPPC and payment of the associated annual charges to the regulator. The application to surrender the permit must include a site report identifying, in particular, any changes in the condition of the site since the time at which the permit was issued. The operator is required to identify any steps that have been taken to avoid any pollution risk resulting from the operation of the installation or return it to a satisfactory state. If on closure the operator satisﬁes the regulator that they have removed any pollution risks and restored the site to a satisfactory state, the regulator accepts the surrender and gives the operator notice of its determination. The permit then ceases to have effect on the date speciﬁed in the notice of determination. If the regulator is not satisﬁed, it has to give notice of its determination stating that the application has been refused.

17.5.5

Wider Scope of IPPC

IPPC takes a wider range of environmental impacts into account than IPC. The current system of IPC regulates emissions to land, water and air. The IPPC regime will additionally take into account: waste avoidance or minimization, energy efﬁciency, accident avoidance and minimization of noise, heat and vibrations. These aims will achieve a higher level of protection as a whole. IPPC also applies to a wider range of industries than IPC. These industries include all installations that are currently regulated under IPC, some installations currently under LAPC, and some installations that are not currently under either regime such as: landﬁll sites, intensive agriculture, large pig and poultry units, and food and drink manufacturers. Under IPPC regulated industries are referred to as ‘installations’ as oppose to ‘processes’ which is the term used for IPC. This change in terminology enables a more integrated approach to regulation; a whole installation

315

Introduction to Health and Safety at Work must be permitted rather than just individual processes within the installation. Guidelines to establish which techniques are BAT are published by the European Commission’s IPPC Bureau. These reference notes are known as BREF notes and provide the basis for national sectoral guidance. The Environment agency has supplementary guidance to cover many issues some; for example, energy efﬁciency, site remediation and noise, are new issues under IPPC. Industry sectors not previously regulated under the Environment Protection Act 1990 such as intensive farming and food and drink installations are also covered by guidance. Once issued, permits for IPPC are to be reviewed periodically in addition to any updating which is made necessary by technological or other changes. Permits have been required for all new installations and existing installations undergoing a substantial change (where there is a change in operation that may have a signiﬁcant negative effect on human beings or the environment) since 31 October 1999. For existing installations IPC permits will continue to be in force until IPPC permits are phased in on a sectoral basis by October 2007.

17.5.6

Duty of care

Waste and the duty of care The duty of care is covered in Part II of the Environmental Protection Act 1990. The duty of care applies to anyone who produces or imports, keeps or stores, transports, treats or disposes of waste. It also applies if they act as a broker and arrange these things. The duty holder is required to take all reasonable steps to keep waste safe. If they give waste to someone else, the duty holder must be sure they are authorized to take it and can transport, recycle or dispose of it safely. Penalty for breach of this law is an unlimited ﬁne. Waste can be anything owned, or a business produces, which a duty holder wants to get rid of. Controlled waste is deﬁned in Box 17.3.

Box 17.3 Controlled waste means household, commercial or industrial waste. It includes any waste from a house, school, university, hospital, residential or nursing home, shop, ofﬁce, factory or any other trade or business premises. It is controlled waste whether it is solid or liquid and even if it is not hazardous or toxic.

316

If the waste comes from a person’s own home, the duty of care does not apply to them. But if the waste is not from the house they live in – for example, if it is waste from their workplace or waste from someone else’s house – the duty of care does apply. Animal waste collected and transported under the Animal By-Products Order 1992 is not subject to the duty of care. Duty holders must take all reasonable steps to fulﬁll the duty and complete some paperwork. What is reasonable depends on what done with the waste. Steps to take if the duty of care applies: When a duty holder has waste they must ➤ stop it escaping from their control and store it safely and securely. They must prevent it causing pollution or harming anyone ➤ keep it in a suitable container. Loose waste in a skip or on a lorry must be covered ➤ if the duty holder gives waste to someone else, they must check that they have authority to take it. The law says the person to whom they give the waste must be authorized to take it. Box 17.4 explains who is allowed to take waste and how the duty holder can check ➤ describe the waste in writing. The duty holder must ﬁll in and sign a transfer note for it and keep a copy. To save on paperwork, the description of the waste can be written on the transfer note (see Box 17.5).

When a person takes waste from someone else they must ➤ be sure the law allows them to take it. Box 17.4 explains who is allowed to take waste ➤ make sure the person giving them the waste describes it in writing. The waste receiver must ﬁll in and sign a transfer note and keep a copy (see Box 17.5).

17.5.7

Hazardous waste

On 16 July 2005 the Hazardous Waste (England and Wales) Regulations and the List of Wastes (England) Regulations, replacing the Special Waste Regulations, come into force. The Special Waste Regulations 1996 transposed the requirements of the European Hazardous Waste Directive (91/689/EEC) which sets out requirements for the controlled management of hazardous (special) waste. The Regulations set out procedures to be followed when disposing of, carrying and receiving hazardous waste. The Special Waste Regulations 1996 were amended by the Special Waste (Amendment) Regulations 1996, the Special Waste (Amendment) Regulations 1997 and the Special Waste (Amendment) (England and Wales)

Summary of the main legal requirements

Box 17.4

Who has authority to take waste?

Council waste collectors The duty holder does not have to do any checking, but if they are not a householder, there is some paperwork to complete. This is explained in Box 17.5.

Registered waste carriers Most carriers of waste have to be registered with the Environment Agency or the Scottish Environment Protection Agency. Look at the carrier’s Certiﬁcate of Registration or check with the Agencies.

Exempt waste carriers The main people who are exempt are charities and voluntary organizations. Most exempt carriers need to register their exemption with the Environment Agency or the Scottish Environment Protection Agency. If someone says they are exempt, ask them why. Check with the Agencies that their exemption is registered.

Holders of waste management licences Some licences are valid only for certain kinds of waste or certain activities. Ask to see the licence. Check that it covers the kind of waste being consigned.

Businesses exempt from waste management licences There are exemptions from licensing for certain activities and kinds of waste. For example, the recycling of scrap metal or the dismantling of scrap

Regulations 2001. These can be found on The Ofﬁce of Public Sector Information (OPSI) website at: www.opsi. gov.uk/legislation/. The new regime includes a requirement for most producers of hazardous waste to notify their premises to the Environment Agency. The facility to notify premises has been available since April 2005. Preliminary guidance on notiﬁcation was published by Defra in January 2005. Guidance on notiﬁcation, including the on-line notiﬁcation facility, and more general guidance on the new regime can be found on the Environment Agency’s hazardous waste pages. See a brief summary of these Regulations in section 17.19.

cars. Most exempt businesses need to register their exemption with the Environment Agency or the Scottish Environment Protection Agency. Check with the Agencies that their exemption is registered.

Authorized transport purposes Waste can also be transferred to someone for ‘Authorized transport purposes’. This means: ➤ the transfer of controlled waste between different places within the same premises ➤ the transport of controlled waste into Great Britain from outside Great Britain, and ➤ the transport by air or sea of controlled waste from a place in Great Britain to a place outside Great Britain.

Registered waste brokers Anyone who arranges the recycling or disposal of waste, on behalf of someone else, must be registered as a waste broker. Check with the Environment Agency or the Scottish Environment Protection Agency that the broker is registered.

Exempt waste brokers Most exempt waste brokers need to register with the Environment Agency or the Scottish Environment Protection Agency. Those who are exempt are mainly charities and voluntary organizations. If someone tells you they are exempt, ask them why. You can check with the Environment Agencies that their exemption is registered.

17.5.8

Applying for a waste management licence

Introduction A waste management licence is a legal document issued under the Environmental Protection Act 1990. There are two types of waste management licence: ➤ a site licence – authorizing the deposit, recovery or disposal of controlled waste in or on land ➤ a mobile plant licence – authorizing the recovery or disposal of controlled waste using certain types of mobile plant.

317

Introduction to Health and Safety at Work

Box 17.5

Filling in paperwork

When waste is passed from one person to another the person taking the waste must have a written description of it. A transfer note must also be ﬁlled in and signed by both persons involved in the transfer. The duty holder can write the description of the waste on the transfer note. Who provides the transfer note is not important as long as it contains the right information. The Government has published a model transfer note with the Code of Practice which can be used if desired. Repeated transfers of the same kind of waste between the same parties can be covered by one transfer note for up to a year. For example, weekly collections from shops. The transfer note to be completed and signed by both persons involved in the transfer, must include: ➤ ➤ ➤ ➤ ➤

what the waste is and how much there is what sort of containers it is in the time and date the waste was transferred where the transfer took place the names and addresses of both persons involved in the transfer ➤ whether the person transferring the waste is the importer or the producer of the waste ➤ details of which category of authorized person each one is. If the waste is passed to someone

➤

➤

➤ ➤

for authorized transport purposes, you must say which of those purposes applies if either or both persons is a registered waste carrier, the certiﬁcate number and the name of the Environment Agency which issued it if either or both persons has a waste management licence, the licence number and the name of the Environment Agency which issued it the reasons for any exemption from the requirement to register or have a licence where appropriate, the name and address of any broker involved in the transfer of waste.

The written description must provide as much information as someone else might need to handle the waste safely. Keeping the papers Both persons involved in the transfer must keep copies of the transfer note and the description of the waste for two years. They may have to prove in Court where the waste came from and what they did with it. A copy of the transfer note must also be made available to the Environment Agency or the Scottish Environment Protection Agency if they ask to see it.

A licence has conditions to make sure that the authorized activities do not cause pollution of the environment, harm to human health or serious detriment to local amenities. Anyone who deposits, recovers or disposes of controlled waste must do so either:

➤ provide guidance on preparing a working plan ➤ set out in writing any additional information required speciﬁcally for the proposals ➤ help work out the application fee, and ➤ say who will deal with the application.

➤ within the conditions of a waste management licence, or ➤ within the conditions of an exemption from licensing

There are ﬁnancial and legal implications to holding a licence and the licensee may want to get independent advice about these.

and must not cause pollution of the environment, harm to human health or serious detriment to local amenities. Otherwise they could be ﬁned and sent to prison. The conditions of the exemptions from licensing are in the Waste Management Licensing Regulations 1994. If an activity may be exempt this should be discussed with the Environment Agency. Before applying for a licence contact the Environment Agency for advice. If a licence is needed the Environment Agency will: ➤ meet to discuss your proposals ➤ explain the application process and provide an application package

318

17.5.9

Applying for a licence

To apply for a waste management licence the licensee must send: ➤ a completed application form ➤ the fee for processing the application (this cannot be refunded) ➤ any additional information which the Agency has asked for in writing and ➤ the supporting information in the checklist on the application form to the Environment Agency at the address shown on the application form.

Summary of the main legal requirements

Box 17.6

What is a working plan?

As part of the licence application a working plan will need to be prepared. This is a document describing how the licensee intends to prepare, develop, operate and restore (where relevant) the site or plant. If they write a comprehensive working plan it will help to avoid delays in processing the application. It may also mean that some of the licence conditions could be less restrictive, giving more opportunity for ﬂexibility in the operations.

When all the information has been received the Environment Agency will write to conﬁrm that the application is complete and that the 4-month period allowed in law for deciding the application has started. The application form will be put on the public register. If the licensee feels that any information on the form should not be made public because it is commercially conﬁdential, they can apply to have that information withheld. The application form tells them how to do this.

17.5.10

Processing the application

Licence applications are processed by the Environment Agency using the waste management licensing process handbook which helps to ensure the licensing service is efﬁcient and consistent. The Environment Agency will consider whether it can write licence conditions which will make sure that the proposed activities do not cause pollution of the environment, harm to human health or serious detriment to local amenities. When processing an application the Agency will also: ➤ check that the activities to be licensed have planning permission or equivalent (where it is needed). It is the licensee’s responsibility to make sure that the activities have the necessary planning permission ➤ consult with other regulatory bodies and ➤ decide whether the licensee is a ﬁt and proper person. If the Environment Agency is not satisﬁed on any aspect, it will write and say what it needs. If the licensee is still unable to satisfy the Agency the application will be rejected.

17.5.11

After a licence is issued

Once the site is licensed, the licensee must comply with the licence conditions at all times. The Environment

Box 17.7 person?

What is a fit and proper

When considering whether the licensee is a ﬁt and proper person the Agency will look at: ➤ whether they have made adequate ﬁnancial provision to cover the licence obligations. If the Agency plans to issue a licence a draft of the licence conditions will be sent to the licensee. They should use this draft to help calculate the amount of ﬁnancial provision needed ➤ whether a technically competent person will be managing the licensed activities ➤ whether the licensee, or another relevant person, have been convicted of a relevant offence.

Agency will make visits to check that the licence conditions are being met. There will be an annual fee to cover the costs of these visits. The fees for waste management licensing are in the Waste Management Licensing (Charges) Scheme. The licence and working plan will be put on the public register. If the licensee thinks any of the information should not be made public because it is commercially conﬁdential, they can apply to have that information withheld. The licensee will be responsible for the obligations arising from that licence until: ➤ the Agency accepts an application to transfer the licence to another person ➤ for a site licence – the Agency accepts the surrender of the licence ➤ for a mobile plant licence – the licensee surrenders the licence. Changes to licence conditions can only be made by the Environment Agency. If the licensee wants to change their operations, this should be discussed with the Agency.

17.5.12

Further information

The law The Environmental Protection Act 1990 ISBN 0-10-544390-5 The Pollution Prevention and Control Act 1999, Stationery Ofﬁce 1999 ISBN 0 10 542499

319

Introduction to Health and Safety at Work The Waste Management Licensing Regulations 1994 Statutory Instrument 1994 No. 1056 (as amended) ISBN 0-11-044056-0 Hazardous Waste (England and Wales) Regulations 2005, The Stationery Ofﬁce SI 2005 No 894.

17.6

Chemicals Regulations 2002 and 2005 amendment Regulations

Government guidance Integrated Pollution Prevention and Control Practical guidance 4th edition Defra 2005. Waste Management Paper 4 Licensing of Waste Management Facilities ISBN 0-11-752727-0 DOE Circular 11/94 Environmental Protection Act 1990: Part II Waste Management Licensing The Framework Directive on Waste (Welsh Ofﬁce Circular 26/94, Scottish Ofﬁce Environment Department Circular 10/94) ISBN 0-11-752975-3 Environment Agency HWR01. A guide to the Hazardous waste Management regulations and the List of Waste regulations in England and Wales.

plant protection products, which have their own speciﬁc laws, have to be classiﬁed and labelled according to CHIP as of July 2004. CHIP 3 requires the supplier of a dangerous chemical to: ➤ identify the hazards (dangers) of the chemical (this is known as ‘classiﬁcation’) ➤ package the chemical safely, and ➤ give information about the hazards to their customers (usually by means of information on the package (e.g. a label) and, if supplied for use at work, a safety data sheet). These are known as supply requirements. ‘Supply’ is deﬁned as making a chemical available to another person. Manufacturers, importers, distributors, wholesalers and retailers are examples of suppliers. The Chemicals (Hazard Information and Packaging for Supply) (Amendment) Regulations 2005, entered into force on 31 October 2005. The regulations are known as

Table 17.2

17.6 Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 and 2005 amendment Regulations 17.6.1

Category of danger

A description of hazard type

Classification

Precise identiﬁcation of the hazard of a chemical by assigning a category of danger and a risk phrase using set criteria

Risk phrase (R-phrase)

A standard phrase which gives simple information about the hazards of a chemical in normal use

Safety phrase (S-phrase)

A standard phrase which gives advice on safety precautions which may be appropriate when using a chemical

Substance

A chemical element or one of its compounds, including any impurities

Preparation

A mixture of substances

Chemical

A generic term for substances and preparations

Tactile warning devices (TWDs)

A small raised triangle applied to a package intended to alert the blind and visually impaired to the fact that they are handling a container of a dangerous chemical

Child resistant fastenings (CRFs)

A closure which meets certain standards intended to protect young children from accessing the hazardous contents of a package

Chain of supply

The successive ownership of a chemical as it passes from manufacturer to its ultimate user

Introduction

CHIP is the Chemicals (Hazard Information and Packaging for Supply) Regulations 2002. Sometimes known as CHIP 3. The aim of CHIP 3 is to ensure that people who are supplied with chemicals receive the information they need to protect themselves, others and the environment. To achieve this, CHIP 3 obliges suppliers of chemicals to identify their hazards (e.g. ﬂammability, toxicity, etc.) and to pass on this information together with advice on safe use to the people they supply the chemicals to. This is usually done by means of package labels and safety data sheets. CHIP applies to most chemicals but not all. The exceptions (which generally have Regulations of their own) are set out in Regulation 3 of CHIP and include cosmetic products, medicinal products, foods, etc. CHIP 3, a new set of Regulations which consolidates and extends the previous ones came into force on 24 July 2003. CHIP 3 is intended to protect people and the environment from the harmful effects of dangerous chemicals by making sure users are supplied with information about the dangers. Many chemicals such as cosmetics and medicines are outside the scope of CHIP and have their own speciﬁc regulatory regimes. However, biocides and

320

Commonly used terms

Summary of the main legal requirements 17.6.2

CHIP 3.1. The regulations bring into legal effect all the new entries, revisions, deletions and amendments to the classiﬁcation and labelling requirements of hazardous substances set out in the 29th Adaptation to Technical Progress (29th ATP) to the Dangerous Substances Directive (European Commission Directive 2004/73/2004). Table 17.2 outlines a description of commonly used terms, and Figure 17.1 shows a summary of what needs to be done to comply.

Classification – Regulation 4

The basic requirement for CHIP 3 is for the supplier to decide whether the chemical is hazardous. CHIP 3 with its Approved Classiﬁcation and Labelling Guide (ACLG), sets out the rules for this. They tell the supplier how to: ➤ decide what kind of hazard the chemical has; and ➤ explain the hazard by assigning a simple sentence that describes it (known as a ‘risk phrase’ or

Are you supppling a chemical? Yes

No

No duties under CHIP

Is the chemical exempted from CHIP? No

Yes

Is the chemical a: Substance

Preparation

Is the substance in the Approved Supply List? Yes

No

Use conventional method or ACLG criteria to derive classification

Gather available data and classify using criteria in ACLG

Is it dangerous?

Use ASL classification and label

Yes

Is it for professional use? Yes

Derive label - decide on symbol (s) - decide on R-phrases - decide on S-phrases - is additional warning information required?

Does it need additional warning information?

No

Provide adequate information

Supply SDS

No

Is it a preparation containing certain amounts of dangerous substances and is for professional use and SDS has been requested? Yes

No

No further action required

Figure 17.1

Summary of what you need to do (Reproduced with courtesy of HSE).

321

Introduction to Health and Safety at Work R-Phrase). This is known as classiﬁcation. Many commonly used substances have already been classiﬁed. They are contained in the CHIP Approved Supply List (ASL) which must be used.

17.6.3 Information and labelling – Regulations 5, 6, 8, 9 and 10 Information has to be supplied for the customers by a data sheet and a label on the package (unless the substance is provided in bulk such as a tanker or by pipeline). If the chemical is supplied for use at work a safety data sheet (SDS) must be provided. CHIP gives sixteen headings for the SDS to set a standard for their quality. CHIP 3 speciﬁes what has to go on to the label including where it must be displayed, the size of the label, name and address of supplier, name of the substance, risk and safety phrases and indications of danger with symbols.

17.6.4 Packaging of Dangerous Substance – Regulation 7 Packaging used for a chemical must be suitable. That means: ➤ the receptacle containing the dangerous substance or dangerous preparation is designed and constructed so that its contents cannot escape ➤ the materials constituting the packaging and fastenings are not susceptible to adverse attack by the contents or liable to form dangerous compounds with the contents ➤ the packaging and fastenings are strong and solid throughout to ensure that they will not loosen and will meet the normal stresses and strains of handling, and ➤ any replaceable fastening ﬁtted to the receptacle containing the dangerous substance or dangerous preparation is designed so that the receptacle can be repeatedly refastened without the contents of the receptacle escaping.

17.6.5 Child resistant fastenings, tactile warnings and other consumer protection measures – Regulation 11 CHIP 3 sets out special requirements for chemicals that are sold to the public. Some have to be ﬁtted with a child-resistant closure to a laydown standard to prevent young children opening containers and swallowing the contents. Some must have tactile danger warning to alert the blind and partially sighted to the danger. This is often a raised triangle.

322

17.6.6

Retention of Data – Regulation 12

Data used for classiﬁcation, labelling, child resistant fasteners and, for preparing the safety data sheet, must be kept for at least three years after the dangerous chemical is supplied for the last time.

17.6.7

Chemical manufacture and storage – The European Commission’s New Chemical strategy. (REACH)

a) What is REACH? REACH stands for Registration, Evaluation, and Authorisation of Chemicals. It is the new EU Chemical legislation, which will come into force on 1 June 2007. The Department of Environment, Food and Rural Affairs (Defra) is responsible for implementing this European Regulation in the UK. In October 2006, Defra nominated HSE to be the UK Competent Authority for REACH, working closely with the Environment Agency, and other partners to manage certain key aspects of the REACH system in the UK. REACH aims to make the people who place chemicals on the market (mainly manufacturers and importers) responsible for understanding and managing the risks associated with their use. REACH is aimed at simplifying the control of chemicals in the European marketplace. It replaces a patchwork of European Directives with a single system. Different types of chemicals are considered in different ways by the legislation, and some are exempt, because they are already covered by speciﬁc laws. More detailed information about REACH can be found at the Defra REACH website, including impact assessment work at the national and Community levels, and consultations. A wide range of industry and commercial sources also offer commentary and advice regarding REACH. The following is a brief background of REACH and summary of key themes.

b) Background The European Commission’s (EC) White Paper of 2001 on a ‘future chemical strategy’ proposed a system that requires chemicals manufactured in quantities of greater than 1 tonne to be ‘registered’, those manufactured in quantities greater than 100 tonnes to be ‘evaluated’, and certain substances of high concern (for example carcinogenic, mutagenic and toxic to reproduction – CMR’s) to be ‘authorized’. The EC adopted its proposal for a new scheme to manage the manufacture, importation and supply of chemicals in Europe on in October 2003. The proposal was then forwarded to the European Parliament and EU’s Council of Ministers for adoption under the co-decision

Summary of the main legal requirements procedure. The European Parliament formally approved a ﬁnal text of REACH in December 2006, and it came into force on 1 June 2007.

that are very persistent and very bioaccumulative (vPvBs); and substances demonstrated to be of equivalent concern, such as endocrine disruptors.

c) Themes

g) Restrictions

The main themes of the REACH system are Registration, Evaluation, Authorization and restrictions, and information exchange.

The Regulation enable restrictions of use to be introduced across the European Community where this is shown to be necessary. Member States or the Commission may prepare such proposals.

d) Registration A requirement on industry to collect, collate and submit data to the European Chemicals Agency (ECHA) on the hazardous properties of all substances (except Polymers and non-isolated intermediates) manufactured or imported into the EU in quantities above 1 tonne per year; and certain substances of high concern, such as carcinogenic, mutagenic and reproductive toxic substances (CMRs) will have to be authorized. Chemicals will be registered in three phases according to the tonnage of the substance: ➤ more than 1000 tonnes a year, or substances of highest concern, must be registered in the ﬁrst 3 years ➤ 100–1000 tonnes a year must be registered in the ﬁrst 6 years ➤ 1–100 tonnes a year must be registered in the ﬁrst 11 years. In addition, industry should prepare risk assessments and provide controls measures for using the substance safely to downstream users.

e) Evaluation There are two types of evaluation: ➤ Dossier evaluation covers all substances manufactured or imported into the EU over 100 tonnes per year. Member States are required to examine and agree any testing proposals put forward by industry as part of their registration package. Member States may also check that the dossiers are complete and compliant. ➤ Substance evaluation permits Member State authorities to consider whether industry need to obtain more information for the Chemical Safety Report (CSR).

f) Authorization Industry must gain Community-wide authorizations for the use of substances considered to be of very high concern. These are substances that are identiﬁed as carcinogenic, mutagenic or toxic to reproduction (CMRs); persistent, bioaccumulative and toxic substances (PBTs); substances

h) Information exchange Manufacturers and/or importers should develop risk reduction measures for all known uses of the chemical including downstream uses. Downstream users should provide detail of their uses to their suppliers. In cases where downstream users decide not to disclose this information, they need to produce their own CSR.

i) European Chemicals Agency The Regulations create a European Chemicals Agency (ECHA) for managing the technical and administrative aspects of the REACH system at Community level. Work is underway to establish this central co-ordinating body, which will be operational in 2008, and will be based in Helsinki, Finland.

j) Competent authority Many European regulatory systems are operated at the national (‘Member State’) level by a Competent Authority in each Member State. Defra announced on 10 October 2006 that HSE has been asked to be the UK Competent Authority for REACH. The Competent Authority’s responsibilities under REACH will be to: ➤ provide advice to manufacturers, importers, downstream users and other interested parties on their respective responsibilities and obligations under REACH (Competent Authorities’ helpdesks) ➤ conduct substance evaluation of prioritized substances and prepare draft decisions ➤ propose harmonized Classiﬁcation and Labelling for CMRs and respiratory sensitizers ➤ identify substances of very high concern for authorization ➤ propose restrictions ➤ nominate candidates to membership of ECA committees on risk Assessment and Socio-economic Analysis ➤ appoint members for the Member State Committee to resolve differences of opinion on evaluation decisions ➤ appoint a member to the Forum for Information Exchange and meet to discuss enforcement matters

323

17.7

Confined Spaces Regulations 1997

Introduction to Health and Safety at Work ➤ provide adequate scientiﬁc and technical resources to the members of the Committees that they have nominated ➤ work closely with the European Chemical Agency in Helsinki. Although REACH will not come into force until June 2007, HSE has already set up an interim helpdesk. It can be contacted on 0845 408 9575 or via email at ukreachca@ hse.gsi.gov.uk.

k) Enforcement Enforcing this very wide-ranging new system presents new challenges to regulators across Europe. REACH places new duties on a range of different businesses. Mostly, the new duties will be on manufacturers and importers of chemicals, but there are also requirements for downstream users of chemicals to share information with their suppliers. Although HSE will play a key role in enforcing REACH, both as the UK Competent Authority and more generally as the UK occupational health and safety regulator, enforcing REACH will fall to a number of regulatory bodies. HSE are working closely with other regulators to support Defra in setting up the framework for enforcing REACH in the UK. Defra planned a consult on enforcement arrangements for REACH in early 2007.

17.6.8

References

Chemical (Hazard Information and Packaging for Supply) Regulations 2002, SI No 2002, 1689, The Stationery Ofﬁce Chemical (Hazard Information and Packaging for Supply) (Amendment) Regulations 2005, SI No 2005, 2571, The Stationery Ofﬁce Chip for Everyone HSG 228, HSE Books 2002 ISBN 07176 2370 X Approved classiﬁcation and labeling guide (ﬁfth edition) L131, HSE Books, 2002 ISBN 07176 2369 6 Approved Supply List. Information approved for the classiﬁcation and labeling of dangerous substances and preparations for supply (seventh edition) L129, HSE Books 2002 ISBN 07176 2368 8 Read the label INDG 352, HSE Books 2002 ISBN 07176 2366 1 Why do I need a safety data sheet? INDG 353 HSE Books 2002 ISBN 07176 2367 X The Idiot’s guide to CHIP INDG 350 HSE Books 2002 The compilation of safety data sheets. Approved Code of Practice (third edition) L130 HSE Books 2002 ISBN 07176 2371 8

324

HSE’s CHIP website:www.hse.gov.uk/hthdir/noframes/ chip/chip0.htm

17.7 Confined Spaces Regulations 1997 17.7.1

Introduction

These Regulations concern any work that is carried on in a place which is substantially (but not always entirely) enclosed, where there is a reasonably foreseeable risk of serious injury from conditions and/or hazardous substances in the space or nearby. Every year about 15 people are killed and a number seriously injured across a wide range of industries (e.g. from simple open top pits to complex chemical plants). Rescuers without proper training and equipment, often become the victims.

17.7.2

Definitions

Confined space – means any place, including any chamber, tank, vat, silo, pit, trench, pipe, sewer, ﬂue, well or similar space in which, by virtue of its enclosed nature, there arises a reasonably foreseeable speciﬁed risk. Specified risk – means a risk to any person at work of: ➤ serious injury arising from a ﬁre or explosion ➤ loss of consciousness arising from an increase in body temperature ➤ loss of consciousness or asphyxiation arising from gas, fume, vapour or the lack of oxygen ➤ drowning arising from the an increase in the level of liquid ➤ asphyxiation arising from a free ﬂowing solid or because of entrapment by it.

17.7.3

Employers duties – Regulation 3

Duties are placed on employers to: ➤ comply regarding any work carried out by employees and ➤ ensure, so far as is reasonably practicable, that other persons (e.g. use competent contractors) comply regarding work in the employer’s control. The self-employed also have duties to comply.

17.7.4 1.

Work in confined space – Regulation 4

No person at work shall enter a conﬁned space for any purpose unless it is not reasonably practicable to achieve that purpose without such entry.

Summary of the main legal requirements 2.

Other than in an emergency, no person shall enter, carry out work or leave a conﬁned space otherwise than in accordance with a safe system of work, relevant to the speciﬁed risks.

17.7.5

Risk assessment

Risk assessment is an essential part of complying with these Regulations and must be done (under the Management of Health and Safety at Work Regulations 1999) to determine a safe system of work. The risk assessment needs to follow a hierarchy of controls to comply. This should start with the measures – both in design and procedures – that can be adopted to enable any work to be carried out outside the conﬁned space. The assessment must be done by a competent person and will form the basis of a safe system of work. This will normally be formalized into a speciﬁc permit to work, applicable to a particular task. The assessment will involve: (a) The general conditions to assess what may or may not be present. Consider: ➤ what has been the previous contents of the space ➤ residues that have been left in the space, for example, sludge, rust, scale and what may be given off if they are disturbed ➤ contamination which may arise from adjacent plant, processes, services, pipes or surrounding land, soil or strata ➤ oxygen deﬁciency and enrichment. There are very high risks if the oxygen content differs signiﬁcantly from the normal level of 20.8%; if it is above this level increased ﬂammability exists, if it is below then impaired mental ability occurs, with loss of consciousness under 16% ➤ physical dimensions and layout of the space can affect air quality. (b) Hazards arising directly from the work being undertaken, consider: ➤ the use of cleaning chemicals and their direct effect or interaction with other substance ➤ sources of ignition for ﬂammable dusts, gases, vapours, plastics and the like. (c) The need to isolate the conﬁned space from outside services or from substances held inside such as liquids, gases, steam, water, ﬁre extinguishing media, exhaust gases, raw materials and energy sources. (d) The requirement for emergency rescue arrangements including trained people and equipment.

17.7.6

Safe system of work

The detailed precautions required will depend on the nature of the conﬁned space and the actual work being

carried out. The main elements of a safe system of work which may form the basis of a ‘permit-to-work’ are: ➤ the type and extent of supervision ➤ competence and training of people doing the work ➤ communications between people inside, from inside to outside and to summon help ➤ testing and monitoring the atmosphere for hazardous gas, fume, vapour, dust etc. and for concentration of oxygen ➤ gas purging of toxic or ﬂammable substances with air or inert gas, such as nitrogen ➤ good ventilation, sometimes by mechanical means ➤ careful removal of residues using equipment which does not cause additional hazards ➤ effective isolation from gases, liquids and other ﬂowing materials by removal of pieces of pipe, blanked off pipes, locked off valves ➤ effective isolation from electrical and mechanical equipment to ensure complete isolation with lock off and a tag system with key security. Need to secure against stored energy or gravity fall of heavy presses etc. ➤ if it is not possible to make the conﬁned space safe, the provision of personal and respiratory protective equipment ➤ supply of gas via pipes and hoses should be carefully controlled ➤ access and egress to give quick unobstructed and ready access and escape ➤ ﬁre prevention ➤ lighting, including emergency lighting ➤ prohibition of smoking ➤ emergencies and rescue ➤ limiting of working periods and the suitability of individuals.

17.7.7

Emergency arrangements – Regulation 5

Before people enter a conﬁned space suitable and sufﬁcient rescue arrangements must be set up. These must: ➤ reduce the risks to rescuers so far as is reasonably practicable ➤ include the provision and maintenance of suitable resuscitation equipment designed to meet the speciﬁed risks. To be suitable and sufﬁcient arrangements will need to cover: ➤ ➤ ➤ ➤ ➤

rescue and resuscitation equipment raising the alarm, alerting rescue and watch keeping safeguarding the rescuers ﬁre safety precautions and procedures control of adjacent plant

325

Introduction to Health and Safety at Work ➤ ➤ ➤ ➤

ﬁrst aid arrangements notiﬁcation and consultation with emergency services training of rescuers and simulations of emergencies size of access openings to permit rescue with full breathing apparatus, harnesses, fall arrest gear and lifelines, which is the normal suitable respiratory protection and rescue equipment for conﬁned spaces.

17.7.8

Training

17.8 Construction (Design and Management) (CDM) Regulations 2007

Speciﬁc, detailed and frequent training is necessary for all people concerned with conﬁned spaces, whether they are acting as rescuers, watchers or those carrying out the actual work inside the conﬁned space. The training will need to cover all procedures and the use of equipment under realistic simulated conditions.

17.7.9

References

Safe work in conﬁned spaces. Conﬁned Spaces Regulations 1997 Approved Code of Practice, Regulations and Guidance. L101 1997 HSE Books ISBN 0 7176 1405 0 Guidance on permit-to-work systems: A guide for the petroleum, chemical and allied industries. HSG250 HSE Books 2005 ISBN 0 7176 2943 0 The Selection Use and Maintenance of Respiratory Protective Equipment: A Practical Guide. HSG53 1998 second edition (reprinted 2001 with minor amendments, due to be updated) HSE Books ISBN 0 7176 61537 5 Respiratory Protective Equipment, Legislative requirements and lists of HSE approved standards and type approved equipment. Fourth edition 1995 HSE Books ISBN 0 7176 1036 5

17.8 Construction (Design and Management) (CDM) Regulations 2007

The key aim of the CDM2007 is to integrate health and safety into the management of the project and to encourage everyone involved to work together to: ➤ improve the planning and management of projects from the very start ➤ identify risks early on so they can be eliminated or reduced at the design or planning stage and the remaining risks can be properly managed ➤ target effort where it can be the most good in terms of health and safety ➤ discourage unnecessary bureaucracy. The regulations are intended to focus attention on planning and management throughout construction projects, from design concepts onwards. The aim is for health and safety considerations to be treated as an essential, but normal part of a projects development – not an after thought or bolt on extra. The effort devoted to planning and managing health and safety should be in proportion to the risks and complexity associated with the project. The focus should always be on action necessary to reduce and manage risks. Any paperwork produced should help with communication and risk management. Paperwork which adds little to the management of risk is a waste of effort, and can be a dangerous distraction from the real business of risk reduction and management. Time and thought invested at the start of the project will pay dividends not only in improved health and safety, but also in: ➤ reductions in the overall cost of ownership, because the structure is designed for safe and easy maintenance and cleaning work, and because key information is available in the health and safety ﬁle ➤ reduced delays ➤ more reliable costings and completion dates ➤ improved communication and co-operation between key parties, and ➤ improved quality of the ﬁnished product.

Note: 17.8.1

Background and Introduction

The following is extracted from the new Approved Code of Practice. The revised Construction (Design and Management) Regulations 2007 (CDM2007) came into force on 6 April 2007. They replace the Construction (Design and Management) Regulations 1994 (CDM94) and the Construction (Health, Safety and Welfare) Regulations 1996 (CHSW). The new Approved Code of Practice replaces the AcOP under CDM94.

326

Typical operating and owning cost of a building are in the ratio: ➤ 1 for construction costs ➤ 5 for maintenance and building operating costs ➤ 200 for business operating costs Source: Royal Academy of Engineering report on – ‘Long Term costs of Owning and Using Buildings’

Summary of the main legal requirements 17.8.2 Outline of Regulations, Application and Notification The Regulations are divided into ﬁve parts. Part 1 of the Regulations deals with matters of interpretation and application. The Regulations apply to all construction work in great Britain and it’s territorial waters, and apply to both employers and self-employed without distinction. Part 2 covers general management duties which apply to all construction projects, including those which are non-notiﬁable. Part 3 sets out additional management duties which apply to projects above the notiﬁcation threshold (projects lasting more than 3 days, or involving more than 500 person days of construction work). These additional duties require particular appointments or particular documents which will assist with the management of health and safety from concept to completion. Part 4 of the Regulations apply to all construction work carried out on construction sites, and covers physical safeguards which need to be provided to prevent danger. Duties to achieve these standards are held by contractors who actually carry out the work, irrespective of whether they are employers or are self-employed. Duties are also held by those who do not do construction work themselves, but control the way in which the work is done. In each case, the extent of the duty is in proportion to the degree of control which the individual or organization has over the work in question. This does not mean that everyone involved with design, planning or management of the project legally must ensure that all the speciﬁc requirements in Part 4 are complied with. They only have duties if, in practice, they exercise sufﬁcient control over the actual working methods, safeguards and site conditions. If, for example, a client speciﬁes that a particular job is done in a particular way then the client will have a duty to make sure that their instructions comply with the requirements. Contractors must not allow work to start or continue unless the necessary safeguards are in place; whether they are providing the safeguards, or using something; for example, a scaffold supplied by someone else. Part 5 of the Regulations covers issues of civil liability; transitional provisions which will apply during the period when the regulations come into force; and amendments and revocations of other legislation. The distinction in the CDM94 Regulations between their application and notiﬁcation of projects was confusing. For the purposes of CDM2007 Regulations, there should only be two types of construction projects:notiﬁable and non-notiﬁable. All of the requirements apply to notiﬁable projects, but the requirements relating to appointments, plans and other paperwork would not apply to non-notiﬁable projects.

SCHEDULE 1 PARTICULARS TO BE NOTIFIED TO THE EXECUTIVE 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.

Date of forwarding. Exact address of the construction site. The name of the local authority where the site is located. A brief description of the project and the construction work which it includes. Contact details of the client (name, address, telephone number and any e-mail address). Contact details of the CDM co-ordinator (name, address, telephone number and any e-mail address). Contact details of the principal contractor (name, address, telephone number and any e-mail address). Date planned for the start of the construction phase. The time allowed by the client to the principal contractor referred to in regulation 15(b) for planning and preparation for construction work. Planned duration of the construction phase. Estimated maximum number of people at work on the construction site. Planned number of contractors on the construction site. Name and address of any contractor already appointed. Name and address of any designer already engaged. A declaration signed by or on behalf of the client that he is aware of his duties under these Regulations.

Figure 17.2 Schedule 1 of CDM2007 Particulars to be notified to the HSE.

Except where the project is for domestic clients, the HSE must be notiﬁed of projects if the construction phase is likely to involve more than (a) 30 days, or (b) 500 person days, of construction work. A F10 (rev) may be used and is available from local HSE ofﬁces or can be completed on line. This form does not have to be used as long as all the particulars shown in Schedule 1 (See Fig 17.2) are provided.

17.8.3

Definition of Construction Regulation 2

Regulation 2 deﬁnes construction work as the following; ‘construction work’ means the carrying out of any building, civil engineering or engineering construction work and includes: (a) The construction, alteration, conversion, ﬁtting out, commissioning, renovation, repair, upkeep, redecoration or other maintenance (including cleaning which involves the use of water or an abrasive at high pressure or the use of corrosive or toxic substances), decommissioning, demolition or dismantling of a structure (b) The preparation for an intended structure, including site clearance, exploration, investigation (but not site survey) and excavation, and the clearance or preparation of the site or structure for use or occupation at its conclusion (c) The assembly on site of prefabricated elements to form a structure or the disassembly on site of

327

Introduction to Health and Safety at Work prefabricated elements which, immediately before such disassembly, formed a structure (d) The removal of a structure or of any product or waste resulting from demolition or dismantling of a structure or from disassembly of prefabricated elements which immediately before such disassembly formed such a structure, and (e) the installation, commissioning, maintenance, repair or removal of mechanical, electrical, gas, compressed air, hydraulic, telecommunications, computer or similar services which are normally ﬁxed within or to a structure. This means that there are some things which may take place on a construction site, like tree planting and horticulture work, putting up marquees, positioning lightweight panels in an open plan ofﬁce and surveying, which are not construction work. Domestic clients are people who have work done on their own home or the home of a family member, that does not relate to a trade or business whether for proﬁt or not. Where an insurance company arranges construction work to be done on a domestic dwelling the insurance company becomes the client for the purposes of CDM. If, however, the insured arranges the work and is reimbursed by the insurance company then the insured is the client. As with all projects, designers and contractors working for domestic clients will have to be competent and take reasonable steps to ensure that anyone they arrange for, or instruct, to manage, design or construct work is also competent. They will also have to co-operate with others involved in the project, to safeguard the health and safety of everyone involved. When preparing or modifying a design, designers will have to avoid risks to the health and safety of anyone constructing, maintaining, using or demolishing the structures concerned, by removing the hazards (and reducing the risks arising from any that remain). Contractors will have to plan, manage and monitor their own work; and ensure that there are suitable welfare facilities.

17.8.4 General Duties of Clients, CDM Coordinators, Principal Contractors and Contractors – Part 2 The Regulations require that appointees are competent and state that: No person on whom these Regulations place a duty shall: (a) appoint or engage a CDM co-ordinator, designer, principal contractor or contractor unless he has taken reasonable steps to ensure that the person to be appointed or engaged is competent (b) accept such an appointment or engagement unless he is competent

328

c)

arrange for or instruct a worker to carry out or manage design or construction work unless the worker is: (i) competent, or (ii) under the supervision of a competent person.

The AcOP goes into considerable detail about the assessment of organizational and individual competence. In both cases it lays down a two-stage approach. ➤ STAGE 1 – assessing a company’s organization and arrangements for health and safety and an individuals task knowledge to assess whether they appreciate the risks ➤ Stage 2 – assessing the company’s and individual’s experience and track record to see if they are capable of doing the work involved. To be competent, an organization or individual must have: ➤ sufﬁcient knowledge of the speciﬁc tasks to be undertaken and the risks which the work will entail ➤ sufﬁcient experience and ability to carry out their duties in relation to the project; to recognize their limitations and take appropriate action in order to prevent harm to those carrying out construction work, or those affected by the work. The Regulations require all duty holders to co-operate and co-ordinate their work with one another to enable people to carry out their duties effectively. Duties are placed on a number of people which is summarized in Table 17.3: All projects require: ➤ non-domestic clients to check the competence of all their appointees; ensure there are suitable management arrangements for the project; allow sufﬁcient time and resources for all stages; provide preconstruction information to designers and contractors ➤ designers to eliminate hazards and reduce risks during design; and provide information about remaining risks ➤ contractors to plan, manage and monitor their own work and that of workers; check the competence of all their appointees and workers; train their own employees; provide information to their workers; comply with the requirements for health and safety on site detailed in Part 4 of the Regulations and other regulations such as the Work at Height Regulations; and ensure there are adequate welfare facilities for their workers ➤ everyone to assure their own competence; co-operate with others and coordinate work so as to ensure the health and safety of construction workers and others who may be affected by the work; report obvious risks; take account of the general principles

Summary of the main legal requirements Table 17.3

Summary of duties under CDM 2007: Source HSE

Clients (excluding domestic clients)

All Construction projects (Part 2 of the Regulations)

Additional Duties for Notifiable projects (Part 3 of Regulations)

• Check competence and resources of all appointees • Ensure there are suitable management arrangements for the project including welfare facilities • Allow sufﬁcient time and resources for all stages • Provide pre-construction information to designers ad contractors

• • • •

CDM Co-ordinators

Designers

Appoint CDM co-ordinator* Appoint principal contractor* Provide pre-construction information to CDM co-ordinator Make sure that the construction phase does not start unless there are suitable: – welfare facilities, and – construction phase plan in place • Provide information relating to the health and safety ﬁle to the CDM co-ordinator • Retain and provide access to the health and safety ﬁle (*There must be a CDM co-ordinator and principal contractor until the end of the construction phase)

• Advise and assist the client with his/her duties; • Notify HSE; • Co-ordinate health and safety aspects of design work and cooperate with others involved in the project; • Facilitate good communication between client, designers and contractors; • Liaise with principal contractor re ongoing design; • Identify, collect and pass on pre-construction information; • Prepare/update health and safety ﬁle. • Eliminate hazards and reduce risks due to design • Provide information about remaining risks

Principal contractors

• Check client is aware of duties and CDM co-ordinator has been appointed • Check HSE has been notiﬁed • Provide any information needed for the health and safety ﬁle • Plan, manage and monitor construction phase in liaison with contractors; • Prepare, develop and implement a written plan and site rules. (Initial plan completed before the construction phase begins.); • Give contractors relevant parts of the plan; • Make sure suitable welfare facilities are provided from the start and maintained throughout the construction phase; • Check competence of all their appointees; • Ensure all workers have site inductions and any further information and training needed for the work; • Consult with the workers; • Liaise with CDM co-ordinator re ongoing design; • Secure the site.

Contractors

• Plan, manage and monitor own work and that of workers; • Check competence of all their appointees and workers; • Train own employees; • Provide information to their workers; • Comply with requirements in Part 4 of the Regulations; • Ensure there are adequate welfare facilities for their workers.

Everyone

• Check own competence • Cooperate with others and coordinate work so as to ensure the health and safety of construction workers and others who may be affected by the work • Report obvious risks • Comply with requirements in schedule 2 (ACOP says 3 but believed a mistake) and Part 4 of the regulations for any work under their control.

of prevention in planning or carrying out construction work; and comply with the requirements in Schedule 3, Part 4 of CDM2007 and other regulations for any work under their control.

• Check client is aware of duties and a CDM co-ordinator has been appointed and HSE notiﬁed before starting work • Co-operate with principal contractor in planning and managing work, including reasonable directions and site rules • Provide details to the principal contractor of any contractor whom he engages in connection with carrying out the work; • Provide any information needed for the health and safety ﬁle • Inform principal contractor of problems with the plan • Inform principal contractor of reportable accidents, diseases and dangerous occurrences

To ensure the revised Regulations are proportionate to risk and the needs of small businesses, and to minimize bureaucracy, the CDM94 requirement for appointment of a Planning Supervisor and Principal Contractor and

329

Introduction to Health and Safety at Work written plans for projects involving ﬁve or more workers has been withdrawn. This does not mean any lessening in the health and safety standards required by the CDM2007 Regulations, as they have strengthened or introduced other requirements. These place the emphasis on risk management, while avoiding disproportionate bureaucracy for smaller projects.

17.8.5 Additional duties where the project is Notifiable As well as the above requirements under 17.8.3, a notiﬁable project requires: ➤ non-domestic clients to appoint a CDM co-ordinator; appoint a Principal Contractor (PC); provide preconstruction information to CDM co-ordinator ➤ check (before construction work starts) that there is a construction phase plan and suitable welfare facilities; and retain and provide access to the health and safety ﬁle ➤ CDM co-ordinators to advise and assist clients with their duties; notify HSE; co-ordinate health and safety aspects of design work; provide pre-construction information to designers and contractors; facilitate good communications communication between client, designers and contractors; liaise with the PC on ongoing design issues; prepare and update the health and safety ﬁle ➤ designers to check, before they start work, that clients are aware of their duties and a CDM co-ordinator has been appointed; check HSE has been notiﬁed; and provide any information needed for the health and safety ﬁle ➤ PCs to plan, manage and monitor the construction phase in liaison with contractors; prepare, develop and implement a written plan (the initial plan to be completed before the construction phase begins); give contractors relevant parts of the plan; make sure suitable welfare facilities are provided from the start and maintained throughout the construction phase; check the competence of all their appointees; provide site inductions; consult with the workers; liaise with the CDM co-ordinator on ongoing design issues; and secure the site ➤ contractors to conﬁrm clients are aware of their duties and a CDM co-ordinator has been appointed; co-operate with the PC in planning and managing work; check HSE has been notiﬁed; and provide any information needed for the health and safety ﬁle; inform PC of problems with plan; inform PC of any reportable accidents, diseases and dangerous occurrences.

330

17.8.6

Roles of duty holders under CDM 2007

a) Clients The role of clients is one of the most difﬁcult areas to cover in law, because of the vast range of interest and expertise in construction, and clients have real questions as to why they should be involved. The HSC are very conscious of the substantial inﬂuence and control that clients exert over construction projects in practice. For example they: ➤ set the tone for projects ➤ control contractual arrangements ➤ make crucial decisions (e.g. budget, time, suitability of designs) select procurement method and construction team/supply chain ➤ may have essential information about site/building. There is a new duty on clients to ensure that suitable project management arrangements for health and safety are in place. Clients are not expected to develop these arrangements themselves and few have the expertise to do so. They should be able to rely on the advice and support of their construction team and, in particular, the CDM co-ordinator. What the HSC expect is for them to exercise their inﬂuence and control responsibly and with due regard for those who will construct, maintain and demolish the structure.

b) CDM Coordinator There is widespread agreement that the role of Planning Supervisor, as developed under CDM94, has not proved as effective as intended. However, views on this tend to be highly polarized. The main problems are that PSs: ➤ are not seen as a natural part of the construction team. To be effective they need to be better integrated with the rest of the design and construction team ➤ are often appointed too late in the project so that they cannot do their job ➤ frequently have to operate at a disadvantage, due to insufﬁcient allocation of resources by the client, in terms both of money and time ➤ have no authority to carry out their duties unless the client effectively empowers them and others co-operate, and ➤ have, fairly or not, become the scapegoat for the bureaucracy linked to CDM. To address these points CDM 2007: ➤ creates a new function – the CDM co-ordinator – to advise and assist the client

Summary of the main legal requirements ➤ places responsibility on clients to ensure that the co-ordinator’s duties are carried out – only they have the information and authority to empower the CDM co-ordinator ➤ explicitly requires the CDM co-ordinator to be appointed before design work starts, with corresponding duties on designers and contractors not to begin work unless a CDM co-ordinator has been appointed, and ➤ requires the client to ensure that the arrangements for managing projects include the allocation of adequate resources (including time).

c) Designers The HSC fully recognise that, as well as health and safety considerations, designers need to take into account issues such as aesthetics, buildability, and cost. The challenge is to ensure that health and safety considerations are not outweighed by aesthetic and commercial priorities and, conversely, that health and safety does not inhibit aesthetics. However, it is a truth, almost universally acknowledged, that designers have considerable potential to eliminate hazards and reduce risks associated with construction work, as well as those associated with building use, maintenance, cleaning, and eventual demolition. As part of balancing their design priorities, designers must take positive steps to use that potential and pay sufﬁcient regard to health and safety in their designs to ensure that in the construction, use, maintenance and demolition of the resulting structures, hazards are removed where possible and any remaining risks reduced. Although this is already stated in the draft guidance, the HSC have explicitly acknowledged the need for such balanced decisions in CDM2007. The HSC also want designers to focus on how their decisions are likely to affect those constructing, maintaining, using or demolishing the structures that they have designed and what they can do, in the design, to remove the hazards, e.g. by not specifying hazardous materials and avoiding the need for processes that create hazardous fumes, vapours, dust, noise or vibration, and reduce the resulting risks where the hazard cannot be removed. The ACoP under CDM94 and guidance already sets out most of this and there is no plan to change these standards. CDM2007 is intended to require designers to eliminate hazards where they can, and then reduce those risks which remain. It does not ask designers to minimize all risks, as the HSC do not expect structures to be restricted to a height of 1 metre! Also, There are often too many variables and no obvious safest design. The duty regarding maintenance is limited in CDM94 to structural matters, but it is important that designers also consider safety during routine maintenance that is affected by their designs – e.g. how are high-level lights and ventilation systems to be maintained?

Designers had no duty under CDM94 to ensure that their designs are safe to use. However, occupiers of workplaces have to ensure that the ﬁnished structure complies with other health and safety law, particularly the Workplace Regulations. To ensure that these issues are addressed at the design stage the CDM2007 extend designers’ duties for ﬁxed workplaces (e.g. ofﬁces, shops, schools, hospitals and factories) to cover safe use. Competent designers should be doing this already – so this is likely to require minimal additional work in practice.

d) Principal Contractor The role of Principal Contractor (PC), introduced when CDM94 came into force, and was built on the longstanding role of main or managing contractor and did not, therefore, require any substantial changes in industry practice. Because of this, as a role it has worked fairly well since CDM94 came into force, and has not changed signiﬁcantly in CDM07. The only substantial change is to make explicit, in the Regulations, the PC’s key role in managing the construction phase, to ensure that it is carried out, so far as is reasonably practicable, safely and without risk to health. This does not mean that the PC has to manage the work of contractors in detail – that is the contractors’ own responsibility. They do have to make sure that they themselves are competent to address the health and safety issues likely to be involved in the management of the construction phase; satisfy themselves that the designers and contractors that they engage are competent and adequately resourced; and ensure that the construction phase is properly planned, managed and monitored, with adequately resourced, competent site management appropriate to the risk and activity. The HSC did not feel it was necessary, legally or otherwise, to specify in CDM2007 that the PC must be a contractor. In over 90% of projects, contractors discharge the role of PC and those with contractor’s experience and expertise are most likely to have the competence and resources to manage the work. The HSC believed that few clients have the competence or resources to manage signiﬁcant construction work and do not want to encourage them to do so, although there is nothing to prevent this if they are competent – which is most likely in simple, low-risk projects.

e) Contractors The only substantive change regarding contractors is to make explicit their own duty to plan, manage and monitor their own work. The intention is that the management duties on PCs and contractors should complement one another, with the contractor’s duty focusing on their own work and the PC’s on the co-ordination of the work of the various contractors.

331

Introduction to Health and Safety at Work 17.8.7

Health and safety file

Under the CDM94 a separate health and safety ﬁle is required for each project. The HSC believe that it would be more useful to have one ﬁle for each site, structure or, occasionally, group of structures – for example, bridges along a road. The ﬁle can then be developed over time as information is added from different projects. The CDM Coordinator therefore has the responsibility to prepare a suitable health and safety ﬁle or update it if one already exists. There are also opportunities to link the health and safety ﬁle with other documents such as the Buildings Regulations Log Book. The potential practical value of the information contained in the ﬁle is also likely to increase as more clients make use of the Internet to share this information with designers and contractors (for example, maintenance contractors could check what access equipment and parts they are likely to need to repair a fault before leaving for the site, saving them and their clients inconvenience, time and money). The contents of the Health and Safety File are given in the ACoP as follows: ➤ a brief description of the work carried out ➤ any residual hazards which remain and how they have been dealt with (e.g. surveys or other information concerning asbestos; contaminated land; water bearing strata; buried services) ➤ key structural principles (e.g. bracing, sources of substantial stored energy – including pre or posttensioned members)and safe working loads for ﬂoors and roofs, particularly where these may preclude placing scaffolding or heavy machinery there ➤ hazardous material used (e.g. lead paint, pesticides, special coatings which should not be burnt off) ➤ information regarding the removal or dismantling of installed plant and equipment (e.g. any special arrangements for lifting, order or other special instructions for dismantling) ➤ health and safety information about equipment provided for cleaning or maintaining the structure ➤ The nature, location and markings of signiﬁcant services, including underground cables; gas supply equipment; ﬁre-ﬁghting services ➤ information and as built drawings of the structure, its plant and equipment (eg, the means of safe access to and from service voids, ﬁre doors and compartmentalization).

the work at height provisions (Regulations 6, 7 and 8), their requirements form the basis of Part 4 and Schedule 2 (Welfare facilities) of the CDM2007 Regulations. The revision is mainly intended to simplify and clarify the wording of the Regulations, without making substantive changes to what is expected in practice. One substantive change, however, has been to broaden the duty regarding explosives to cover the important issues of security and safety of storage and transport, as well as safety in use. However, some issues already covered by the Workplace Regulations are particularly important in construction. These include trafﬁc management and lighting. Because these are so important CDM2007 duplicate aspects of the Workplace Regulations requirements, although that was not legally necessary. The issues covered by Part 4 apply to all construction projects and are as follows.

a) General – Regulations 25 Duties to comply with this part are placed on contractor or other person who controls the way in which construction work is carried on. Duty placed on workers to report any defect they are aware of which may endanger the health and safety of themselves or another person.

b) Safe place of work – Regulation 26 This regulation requires so far as is reasonably practicable (sfarp): ➤ safe access and egress to places of work ➤ maintenance of access and egress ➤ that people are prevented from gaining access to unsafe access or workplaces ➤ provision of safe places of work with adequate space and suitable for workers.

c) Good order and site security – Regulation 27 ➤ Requires that all parts of a construction be kept, sfarp, in good order and in a reasonable state of cleanliness ➤ Where necessary in the interests of health and safety the site’s perimeter should be identiﬁed, signed and fenced off ➤ No timber or other materials with projecting nails or similar sharp objects shall be used or allowed to remain if they could be a source of danger.

17.8.8 Part 4 Health and Safety on Construction Sites

d) Stability of structures – Regulations 28

The Construction (Health, Safety and Welfare) Regulations 1996 (CHSW) have been revoked by CDM2007. Without

➤ any new or existing structure which may be, or become, weak does not collapse accidentally

332

All practical steps must be taken to ensure that:

Summary of the main legal requirements ➤ temporary supporting structures are designed installed and maintained so as to withstand all foreseeable loads ➤ a structure is not overloaded so as to be a source of danger.

e) Demolition or dismantling – Regulation 29 ➤ Demolition or dismantling must be planned and carried out so as to prevent danger or reduce it to as low a level as is reasonably possible ➤ Arrangements must be recorded before the work takes place.

f) Explosives – Regulation 30 ➤ Explosives, sfarp, shall be stored, transported and used safely and securely ➤ Explosives may only be ﬁred if suitable and sufﬁcient steps have been taken to ensure no one is exposed to risk of injury.

g) Excavations – Regulation 31

h) Cofferdams and caissons – Regulation 32 Every cofferdams or caissons must be: ➤ suitably designed and constructed ➤ appropriately equipped so that people can gain shelter or escape if water or material enters ➤ properly maintained. A cofferdam or caisson may be used to carry out construction only if: ➤ it and any work equipment and materials which affect its safety have been inspected by a competent person: ➤ at the start of the shift (only one report required every 7 days) ➤ after any event likely to affect its strength or stability ➤ the person inspecting is satisﬁed that it is safe. Where the person who carries out the inspection has informed the person on whose behalf the inspection was carried out, work must cease until the relevant matters have been corrected.

All practicable steps shall be taken to prevent danger to people including, where necessary, supports or battering to ensure that:

i) Reports of Inspection – Regulation 33

➤ excavations do not collapse accidentally ➤ no material from side, roof or adjacent is dislodged or falls ➤ a person is prevented from being buried or trapped by a fall of material ➤ persons, work equipment or any accumulation of material are prevented from falling into the excavation ➤ any part of an excavation or ground adjacent is not overloaded by work equipment or material.

➤ inform the person for whom they carried out the inspection if they are not satisﬁed that construction work can be carried out safely ➤ prepare a report with the particulars set out in schedule 3 to the Regulations as shown in Figure 17.3.

No construction work may be carried out in an excavation where any supports or battering have been provided unless: ➤ it has been inspected by a competent person: ➤ at the start of the shift (only one report required every 7 days) ➤ after any event likely to affect the strength or stability of the excavation ➤ after any material accidentally falls or is dislodged. ➤ the person inspecting is satisﬁed that it is safe. Where the person who carries out the inspection has informed the person on whose behalf the inspection was carried out, work must cease until the relevant matters have been corrected.

Before the end of the shift in which the report was completed, the person who carries out the inspection under Regulations 31 or 32 must:

A copy of the report must be provided within 24 hours of the relevant inspection. If the inspector is an employee

SCHEDULE 3 Regulation 33(1)(b) PARTICULARS TO BE INCLUDED IN A REPORT OF INSPECTION 1. Name and address of the person on whose behalf the inspection was carried out. 2. Location of the place of work inspected. 3. Description of the place of work or part of that place inspected (including any work equipment and materials). 4. Date and time of the inspection. 5. Details of any matter identiﬁed that could give rise to a risk to the health or safety of any person. 6. Details of any action taken as a result of any matter identiﬁed in paragraph 5 above. 7. Details of any further action considered necessary. 8. Name and position of the person making the report.

Figure 17.3

333

Introduction to Health and Safety at Work or works under someone else’s control, that person must ensure that these duties are performed. Records must be kept at the site where the inspection was carried out until the work is complete and then for 3 months. Extracts must be provided for an inspector as they require.

j) Energy Distribution installations – Regulation 34 Energy distribution installations must be suitably located, checked and clearly indicated. Where there is a risk from electric power cables: ➤ they should be routed away from the risk areas, or ➤ the power should be cut off, or ➤ if the above safety measures are not reasonably practicable suitable warning notices, with barriers to exclude work equipment and suspended protections where vehicles have to pass underneath, or ➤ something equally as safe must be done. No construction work which is liable to create a risk to health or safety from an underground service, or from damage to or disturbance of it, shall be carried out unless suitable and sufﬁcient steps have been taken to prevent such risk, sfarp.

them from a place of safety to see any approaching vehicle ➤ there is sufﬁcient separation between vehicles and pedestrians to ensure safety or, where this is not reasonably practicable: (i) there are provided other means for the protection of pedestrians, and (ii) there are effective arrangements for warning any person liable to be crushed or trapped by any vehicle of its approach ➤ any loading bay has at least one exit point for the exclusive use of pedestrians, and ➤ where it is unsafe for pedestrians to use a gate intended primarily for vehicles, one or more doors for pedestrians is provided in the immediate vicinity of the gate, is clearly marked and is kept free from obstruction. Every trafﬁc route shall be: ➤ indicated by suitable signs ➤ regularly checked, and ➤ properly maintained. No vehicle shall be driven on a trafﬁc route unless, sfarp, that trafﬁc route is free from obstruction and permits sufﬁcient clearance.

k) Prevention of drowning – Regulation 14 Where persons could fall into water or other liquid steps must be taken to: ➤ prevent, so far as is reasonably practicable, people from falling ➤ minimize the risk of drowning if people fall ➤ provide, use and maintain suitable rescue equipment to ensure prompt rescue. Transport to work by water must be suitable and sufﬁcient and any vessel must not be overcrowded or overloaded.

l) Traffic routes – Regulation 15 Every construction site shall be organized in such a way that, so far as is reasonably practicable, pedestrians and vehicles can move safely. Trafﬁc routes shall be suitable for the persons or vehicles using them, sufﬁcient in number, in suitable positions and of sufﬁcient size. Must take steps to steps ensure that: ➤ pedestrians or vehicles may use it without causing danger to the health or safety of persons near it ➤ any door or gate for pedestrians which leads onto a trafﬁc route is sufﬁciently separated from it to enable

334

m) Vehicles – Regulation 37 The unintended movement of any vehicle must be prevented or controlled. Suitable and sufﬁcient steps shall be taken to ensure that, where a person may be endangered by the movement of any vehicle, the person having effective control of the vehicle shall give suitable and sufﬁcient warning. Any vehicle being used for the purposes of construction work, shall when being driven, operated or towed: ➤ be driven, operated or towed in a safe manner; and ➤ be loaded so that it can be driven, operated or towed safely. No person shall ride on any vehicle being used for the purposes of construction work except in a safe place provided. No person shall remain on any vehicle during the loading or unloading of any loose material unless a safe place of work is provided and maintained. Suitable measures must be taken to prevent any vehicle from falling into any excavation or pit, or into water, or overrunning the edge of any embankment or earthwork.

Summary of the main legal requirements n) Prevention of risk from fire – Regulation 38

➤ ﬁres or explosions ➤ ﬂooding, or ➤ substances liable to cause asphyxiation.

Every person at work on a construction site shall, sfarp, be instructed in the correct use of any ﬁre-ﬁghting equipment which it may be necessary for them to use. Where a work activity may give rise to a particular risk of ﬁre, a person shall not carry out such work unless suitably instructed.

o) Emergency Procedures – Regulation 39

r) Fresh air – Regulation 42

Where necessary, emergency procedures must be prepared and, where necessary, implemented to deal with any foreseeable emergency. They must include procedures for any necessary evacuation of the site or any part thereof. The arrangements must take account of:

Steps must be taken to ensure, sfarp, that every place of work or approach has sufﬁcient fresh or puriﬁed air to ensure that the place or approach is safe and without risks to health. Any plant used for the provision of fresh, must include, where necessary, an effective device to give visible or audible warning of any failure of the plant.

Steps must be taken to prevent injury arising from:

(a) the type of work for which the construction site is being used (b) the characteristics and size of the construction site and the number and location of places of work on that site (c) the work equipment being used (d) the number of persons likely to be present on the site at any one time, and (e) the physical and chemical properties of any substances or materials on or likely to be on the site. Steps must be taken to make people on site familiar with the procedures and test the procedures at suitable intervals.

p) Emergency routes and exits – Regulation 40 A sufﬁcient number of suitable emergency routes and exits shall be provided to enable any person to reach a place of safety quickly in the event of danger. An emergency route or exit (or as appropriate trafﬁc route) provided must: ➤ lead as directly as possible to an identiﬁed safe area ➤ be kept clear and free from obstruction and, where necessary, provided with emergency lighting so that such emergency route or exit may be used at any time ➤ be indicated by suitable signs.

Temperature and weather protection – Regulation 43 Steps must be taken to ensure, sfarp, that during working hours the temperature at any place of work indoors is reasonable having regard to it’s purpose. Every place of work outdoors must, where necessary, sfarp, and having regard to the purpose for which that place is used and any protective clothing or work equipment provided, be so arranged that it provides protection from adverse weather.

s) Lighting – Regulation 44 Every place of work and approach thereto and every trafﬁc route shall be provided with suitable and sufﬁcient lighting, which shall be, sfarp, be by natural light. The colour of any artiﬁcial lighting provided shall not adversely affect or change the perception of any sign or signal provided for the purposes of health and safety. Suitable and sufﬁcient secondary lighting shall be provided in any place where there would be a risk to the health or safety of any person in the event of failure of primary artiﬁcial lighting.

17.8.8

a) Sanitary conveniences 1.

q) Fire detection and fire-fighting – Regulation 41 Where necessary duty holders must provide suitable and sufﬁcient: 2. ➤ ﬁre-ﬁghting equipment; and ➤ ﬁre detection and alarm systems; 3. which shall be suitably located. The equipment must be examined and tested at suitable intervals, properly maintained and suitably indicated by signs. If non-automatic must be easily accessible.

Welfare facilities – Schedule 2

Suitable and sufﬁcient sanitary conveniences shall be provided or made available at readily accessible places. So far as is reasonably practicable, rooms containing sanitary conveniences shall be adequately ventilated and lit. So far as is reasonably practicable, sanitary conveniences and the rooms containing them shall be kept in a clean and orderly condition. Separate rooms containing sanitary conveniences shall be provided for men and women, except where and so far as each convenience is in a separate room the door of which is capable of being secured from the inside.

335

Introduction to Health and Safety at Work b) Washing facilities 4.

5.

6.

7. 8. 9.

10.

Suitable and sufﬁcient washing facilities, including showers if required by the nature of the work or for health reasons, shall so far as is reasonably practicable be provided or made available at readily accessible places. Washing facilities shall be provided: (a) in the immediate vicinity of every sanitary convenience, whether or not provided elsewhere, and (b) in the vicinity of any changing rooms required by paragraph 15 whether or not provided elsewhere. Washing facilities shall include: (a) a supply of clean hot and cold, or warm, water (which shall be running water so far as is reasonably practicable) (b) soap or other suitable means of cleaning, and (c) towels or other suitable means of drying. Rooms containing washing facilities shall be sufﬁciently ventilated and lit. Washing facilities and the rooms containing them shall be kept in a clean and orderly condition. Subject to paragraph 10 below, separate washing facilities shall be provided for men and women, except where and so far as they are provided in a room the door of which is capable of being secured from inside and the facilities in each such room are intended to be used by only one person at a time. Paragraph 9 above shall not apply to facilities which are provided for washing hands, forearms and face only.

c) Drinking water 11.

12.

13.

An adequate supply of wholesome drinking water shall be provided or made available at readily accessible and suitable places. Every supply of drinking water shall be conspicuously marked by an appropriate sign where necessary for reasons of health and safety. Where a supply of drinking water is provided, there shall also be provided a sufﬁcient number of suitable cups or other drinking vessels unless the supply of drinking water is in a jet from which persons can drink easily.

d) Changing rooms and lockers 14

(1) Suitable and sufﬁcient changing rooms shall be provided or made available at readily accessible places if: (a) a worker has to wear special clothing for the purposes of their work, and (b) they cannot, for reasons of health or propriety, be expected to change elsewhere

336

being separate rooms for, or separate use of rooms by, men and women where necessary for reasons of propriety. 14(2) Changing rooms shall: (a) be provided with seating (b) include, where necessary, facilities to enable a person to dry any such special clothing and their own clothing and personal effects. 14(3) Suitable and sufﬁcient facilities shall, where necessary, be provided or made available at readily accessible places to enable persons to lock away: (a) any such special clothing which is not taken home (b) their own clothing which is not worn during working hours, and (c) their personal effects.

e) Facilities for rest 15(1) Suitable and sufﬁcient rest rooms or rest areas shall be provided or made available at readily accessible places. 15(2) Rest rooms and rest areas shall: (a) include suitable arrangements to protect nonsmokers from discomfort caused by tobacco smoke (b) be equipped with an adequate number of tables and adequate seating with backs for the number of persons at work likely to use them at any one time (c) where necessary, include suitable facilities for any person at work who is a pregnant woman or nursing mother to rest lying down (d) include suitable arrangements to ensure that meals can be prepared and eaten (e) include the means for boiling water, and (f) be maintained at an appropriate temperature.

17.8.9

Civil liability – Regulation 45

The Management Regulations (Management of Health and Safety at Work Regulations 1999) were amended in 2003 to provide employees with a right of action in civil proceedings, in relation to breach of duties by their employer. To maintain consistency CDM2007 carries forward with three small exceptions, the rights of civil action in CDM and CHSW and also allows employees to take action in the civil courts for injuries resulting from a failure to comply with duties under these Regulations.

17.8.10

Enforcement

General The enforcement demarcation between HSE and Local Authorities (LAs) in respect of construction work is

Summary of the main legal requirements

➤ all notiﬁable construction work, except that undertaken by people in LA–enforced premises who normally work on the premises ➤ work done to the exterior of the premises, and ➤ work done in segregated areas.

Fire safety in construction work, HSG 168, 1997 HSE Books ISBN 0-7176-1332-1 Health and safety in excavations, HSG 185, 1999 HSE Books ISBN 0-7176-1563-4 Health and safety in roof work, revised, HSG33, 1999 HSE Books ISBN 0-7176-1425-5 Safe use of vehicles on construction sites, HSG 144, 1998 HSE Books ISBN 0-7176-1610-X Backs for the future, HSG 149, HSE Books ISBN 0-7176-1122-1

Enforcement in respect of ﬁre – Regulation 46 This regulation of CDM2007 is given in full.

46. (1) Subject to paragraphs (2) and (3): (a) in England and Wales the enforcing authority within the meaning of article 25 of the Regulatory Reform (Fire Safety) Order 2005(a); or (b) in Scotland the enforcing authority within the meaning of section 61 of the Fire (Scotland) Act 2005(b), shall be the enforcing authority in respect of a construction site which is contained within, or forms part of, premises which are occupied by persons other than those carrying out the construction work or any activity arising from such work as regards regulations 39 and 40, in so far as those regulations relate to ﬁre, and regulation 41. (2) In England and Wales paragraph (1) only applies in respect of premises to which the Regulatory Reform (Fire Safety) Order 2005 applies. (3) In Scotland paragraph (1) only applies in respect of premises to which Part 3 of the Fire (Scotland) Act 2005 applies(c).

17.9 Construction (Head Protection) Regulations 1989 17.9.1

These Regulations apply to ‘building operations’ and ‘works of engineering construction’ as deﬁned originally by the Factories Act 1961.

17.9.2

Provision and maintenance

Every employer must provide suitable head protection for each employee and shall maintain it and replace it whenever necessary. A similar duty is placed on selfemployed people. The employer must make an assessment and review it as necessary, to determine whether the head protection is suitable. Accommodation must be provided for head protection when it is not in use.

17.9.3 17.8.11

Application

Ensuring that head protection is worn – Regulation 4

References

Construction (Design and Management) Regulations 2007, Approved Code of Practice, L144, 2007 HSE Books ISBN 9780717662234 Managing Health and safety in Construction, Guidance, HSG 224, 2007 HSE Books ISBN 0-7176-21391 Health and Safety in Construction HSG150 (rev1), 2001 HSE Books ISBN 0-7176-2106-5 Electrical safety on construction sites, HSG141, 1995 HSE Books ISBN 0-7176-1000-4

Every employer shall ensure, so far as is reasonably practicable, that each employee (and any other person over whom they have control) at work wears suitable head protection, unless there is no foreseeable risk of injury to their head other than through falling.

17.9.4

Rules and directions – Regulation 5

The person in control of a site may make rules regulating the wearing of suitable head protection. These must be in writing. An employer may give directions requiring their employees to wear head protection.

337

17.9 Construction (Head Protection) Regulations 1989

currently set out in the Health and Safety (Enforcing Authority) Regulations 1998, and in Regulations 3 (4) and 22 of CDM94. Interpretation of these requirements is not straightforward, but the practical effect is that LAs were prevented from enforcing CDM. The HSC wished to simplify this by omitting Regulations 3 (4) and 22 from CDM2007. The effect of this that under CDM2007 HSE would then be the enforcing authority for:

Introduction to Health and Safety at Work 17.9.5 Wearing of suitable head protection, reporting loss – Regulations 6, 7, 9 Every employee who has been provided with suitable head protection shall wear it when required to do so by rules made or directions given under Regulation 5 of these Regulations. They must make full and proper use of it and return it to the accommodation. Employees must take reasonable care of head protection, and report any loss or obvious defect. Exemption certiﬁcates, issued by the HSE, are allowed.

17.10

Health and Safety (Consultation with Employees) Regulations 1996

17.9.6

References

Head protection for Sikhs wearing turbans INDG262 Construction (Head Protection) Regulations 1989 Guidance on regulations L 102 (rev) 1998 HSE Books. ISBN 07176 1478 6

The guidance emphasizes the difference between informing and consulting. Consultation involves listening to employees’ views and taking account of what they say before any decision is taken.

17.10.3

Persons to be consulted – Regulation 4

Employers must consult with either: ➤ the employees directly, or ➤ one or more persons from a group of employees, who were elected by employees in that group to represent them under these regulations. They are known as ‘Representatives of Employee Safety’ (ROES). Where ROES are consulted, all employees represented must be informed of: ➤ the names of ROES ➤ the group of employees represented. Employers shall not consult a ROES if:

17.10

17.10.1

Health and Safety (Consultation with Employees) Regulations 1996 Application

These Regulations apply to all employers and employees in Great Britain except: ➤ where employees are covered by safety representatives appointed by recognized trade unions under the Safety Representatives and Safety Committees Regulations 1977 ➤ domestic staff employed in private households ➤ crew of a ship under the direction of the master.

17.10.2 Employers’ duty to consult – Regulation 3 The employer must consult relevant employees in good time with regard to: ➤ the introduction of any measure which may substantially affect their health and safety ➤ the employer’s arrangements for appointing or nominating competent persons under the Management of Health and Safety at Work Regulations 1999 ➤ any information required to be provided by legislation ➤ the planning and organization of any health and safety training required by legislation ➤ the health and safety consequences to employees of the introduction of new technologies into the workplace.

338

➤ ➤ ➤ ➤

the ROES does not wish to represent the group the ROES has ceased to be employed in that group the election period has expired the ROES has become incapacitated from carrying out their functions.

If an employer decides to consult directly with employees they must inform them and ROES of that fact. Where no ROES is elected employers will have to consult directly.

17.10.4

Duty to provide information – Regulation 5

Employers must provide enough information to enable ROES to participate fully and carry out their functions. This will include: ➤ what the likely risks and hazards arising from their work may be ➤ reported accidents and diseases etc. under RIDDOR 95 ➤ the measures in place, or which will be introduced, to eliminate or reduce the risks ➤ what employees ought to do when encountering risks and hazards. An employer need not disclose information which: ➤ could endanger national security ➤ violates a legal prohibition ➤ relates speciﬁcally to an individual without their consent

Summary of the main legal requirements ➤ could substantially hurt the employers undertaking or infringe commercial security ➤ was obtained in connection with legal proceedings.

ROES have the following functions (but no legal duties):

17.11.1

Introduction

➤ to make representations to the employer on potential hazards and dangerous occurrences related to the group of employees represented ➤ to make representations to the employer on matters affecting the general health and safety of relevant employees ➤ to represent the group of employees for which they are the ROES in consultation with inspectors.

The 2002 COSHH Regulations have updated the 1999 Regulations with a few changes which include: additional deﬁnitions like ‘inhalable dust’ and ‘health surveillance’; clarify and extend the steps required under risk assessment; introduces a duty to deal with accidents and emergencies. The 2005 Amendment Regulations replace Regulation 7 (7) and (8) by substituting new requirements to observe principles of good practice for the control of exposure to substances hazardous to health introduced by Schedule 2A, to ensure that workplace exposure limits are not exceeded, and to ensure in respect of carcinogens and asthmagens that exposure is reduced to as low a level as is reasonably practicable. They also introduce a single new Workplace Exposure Limit for substances hazardous to health which replaces occupational exposure standards and maximum exposure limits. The amendment regulations introduce a duty to review control measures other than the provision of plant and equipment, including systems of work and supervision, at suitable intervals. COSHH covers most substances hazardous to health found in workplaces of all types. The substances covered by COSHH include:

17.10.5

Functions of ROES – Regulation 6

17.10.6 Training, time off and facilities – Regulation 7 Where an employer consults ROES, they shall: ➤ Ensure that each ROES receives reasonable training at the employers’ expense ➤ allow time off with pay during the ROES working hours to perform the duties of a ROES and while a candidate for election ➤ such other facilities and assistance that ROES may reasonably require.

17.10.7 Civil liability and complaints – Regulation 9 and Schedule 2 Breach of these Regulations does not confer any right of action in civil proceedings subject to Regulation 7 (3) and schedule 2 relating to complaints to industrial tribunals. A ROES can complain to an industrial tribunal that: ➤ their employer has failed to permit time off for training or to be a candidate for election ➤ their employer has failed to pay them as set out in Schedule 1 to the Regulations.

17.10.8

Elections

The guidance lays down some ideas for the elections, although there are no strict rules. ROES do not need to be conﬁned to consultation related to these Regulations. Some employers have ROES sitting on safety committees and taking part in accident investigation similar to union Safety Representatives.

17.10.9

References

A guide to the Health and Safety (consultation with Employees) Regulations 1996. L95, HSE Books ISBN 0-7176-1234-1

➤ substances used directly in work activities (e.g. solvents, paints, adhesives, cleaners) ➤ substances generated during processes or work activities (e.g. dust from sanding, fumes from welding) ➤ naturally occurring substances (e.g. grain dust). But COSHH does not include: ➤ asbestos and lead, which have speciﬁc regulations ➤ substances which are hazardous only because they are: ➤ radioactive ➤ simple asphyxiants ➤ at high pressure ➤ at extreme temperatures ➤ have explosive or ﬂammable properties (separate Dangerous substances regulations, DSEAR, cover these) ➤ biological agents if they are not directly connected with work and are not in the employer’s control, such as catching ﬂu from a workmate.

339

Control of Substances Hazardous to Health Regulations (COSHH) 2002 and 2005 Amendment

Control of Substances Hazardous to Health Regulations (COSHH) 2002 and 2005 Amendment

17.11

17.11

Introduction to Health and Safety at Work 17.11.2 Definition of substance hazardous to health – Regulation 2 The range of substances regarded as hazardous under COSHH are: ➤ substances or mixtures of substances classiﬁed as dangerous to health under the Chemicals (Hazard, Information and Packaging for Supply) Regulations 2002 (CHIP). These have COSHH warning labels and manufacturers must supply data sheets. They cover substances that are: very toxic, toxic, harmful, corrosive or irritant under CHIP ➤ substances with a workplace exposure limit as listed in EH40 published by the HSE ➤ biological agents (bacteria and other microorganisms) if they are directly connected with the work ➤ any kind of dust in a concentration speciﬁed in the regulations, i.e. ➤ 10 mg/m3, as a time-weighted average over an 8-hour period, of total inhalable dust ➤ 4 mg/m3, as a time-weighted average over an 8-hour period, of respirable dust ➤ any other substance which has comparable hazards to people’s health but which, for technical reasons, is not covered by CHIP. ➤ Workplace exposure limit for a substance hazardous to health means the exposure limit approved by the HSC for that substance in relation to the speciﬁed reference period when calculated by a method approved by the HSC, as contained in HSE publication ‘EH/40 Workplace Exposure Limits 2005’ as updated from time to time.

17.11.3

Duties under COSHH – Regulation 3

The duties placed on employers under these Regulations are extended to (except for health surveillance, monitoring and information and training) persons who may be on the premises but not employed whether they are at work or not, for example, visitors and contractors.

17.11.4

General requirements

There are seven basic steps to comply with COSHH, they are: 1. 2. 3. 4. 5. 6.

Assess the risks to health Decide what precautions are needed Prevent or adequately control exposure Ensure that control measures are used and maintained Monitor the exposure of employees to hazardous substances Carry out appropriate health surveillance where necessary

340

7.

Ensure employees are properly informed, trained and supervised.

17.11.5

Steps 1 and 2 – assessment of health risk – Regulation 6

No work may be carried where employees are liable to be exposed to substances hazardous to health unless: ➤ a suitable and sufﬁcient risk assessment, including the steps need to meet COSHH, has been made. The assessment must be reviewed and changes made regularly and immediately if: ➤ if it is suspected that it is no longer valid ➤ there has been a signiﬁcant change in the work to which it relates. ➤ the results of any monitoring carried out in accordance with Regulation 10 show it to be necessary The assessment involves both identifying the substance present in the workplace; assessing the risk it presents in the way it is used; and deciding what precautions (and health surveillance) are needed. Where more than four employees are employed the signiﬁcant ﬁndings must be recorded and the steps taken to comply with Regulation 7.

17.11.6

Step 3 – prevention or control of exposure – Regulation 7

Every employer must ensure that exposure to substances hazardous to health is either: ➤ prevented or, where this is not reasonably practicable ➤ adequately controlled. Preference must be given to substituting with a safer substance. Where it is not reasonably practicable to prevent exposure, protection measures must be adopted in the following order of priority: ➤ The design and use of appropriate work processes, systems and engineering controls and the provision and use of suitable work equipment ➤ The control of exposure at source, including adequate ventilation systems and appropriate organizational measures, and ➤ Where adequate control of exposure cannot be achieved by other means, the additional provision of suitable personal protective equipment. The measures must include: ➤ Safe handling, storage and transport (plus waste) ➤ Reducing to a minimum required for the work the number of employees exposed, the level and duration

Summary of the main legal requirements of exposure, the quantity of substance present at the workplace ➤ The control of the working environment including general ventilation ➤ Appropriate hygiene measures. Control of exposure shall only be treated as adequate if: ➤ The principles of good practice as set out in schedule 2A are applied ➤ Any workplace exposure limit approved for that substance is not exceeded, and ➤ For a carcinogen (in schedule 1 or with risk phrase R45, R46 or R49) or sensitizer (Risk phrases R42 or R42/43) or asthmagen (Section C of HSE publication on Asthmagens (ISBN 0-7176-1465-4) exposure is reduced to as low a level as is reasonably practicable.

Principles of Good Practice for the Control of Exposure to Substances Hazardous to Health. (Schedule 2A) ➤ Design and operate processes and activities to minimize emission, release and spread of substances hazardous to health. ➤ Take into account all relevant routes of exposure – inhalation, skin absorption and ingestion – when developing control measures. ➤ Control exposure by measures that are proportionate to the health risk. ➤ Choose the most effective and reliable control options which minimize the escape and spread of substances hazardous to health. ➤ Where adequate control of exposure cannot be achieved by other means, provide, in combination with other control measures, suitable PPE. ➤ Check and review regularly all elements of control measures for their continuing effectiveness. ➤ Inform and train all employees on the hazards and risks from the substances with which they work and the use of control measures developed to minimize the risks. ➤ Ensure that the introduction of control measures does not increase the overall risk to health and safety.

Additionally, respiratory protective equipment must be: ➤ suitable for the purpose ➤ comply with the EC Directive Regulations or ➤ if there is no requirement imposed by these regulations, be of a type or shall conform to a standard, approved by the HSE. Where exposure to a Carcinogen or Biological Agent is involved, additional precautions are laid down in Regulation 7.

17.11.7

Step 4 – use, maintenance, examination and test of control measures – Regulations 8 and 9

➤ Every employer must take all reasonable steps to ensure that control measures, PPE or anything else provided under COSHH, are properly used or applied. ➤ Employees must make full and proper use of control measures, PPE or anything else provided. Employees must, as far as is reasonable, return items to accommodation and report defects immediately. Employers shall also: ➤ properly maintain and keep clean plant and equipment, other engineering controls and PPE. ➤ In the case of the provision of systems of work and supervision or similar review at suitable intervals and revise as necessary. ➤ carry out thorough examination and tests on engineering controls: ➤ in the case of Local Exhaust Ventilation (LEV) at least once every 14 months (except those in Schedule 4 which covers blasting of castings – monthly; dry grinding, polishing or abrading of metal for more than 12 hours per week – 6 months; and jute manufacture – 6 months) ➤ in any other case, at suitable intervals ➤ carry out thorough examination and tests where appropriate (except on disposable items) on respiratory protective equipment at suitable intervals ➤ keep a record of examination and tests for at least 5 years ➤ check, properly store, repair/replace and safely dispose of contaminated PPE as necessary.

17.11.8

Step 5 – monitoring exposure – Regulation 10

Employers must monitor exposure: PPE must conform to the Personal Protective Equipment (EC Directive) Regulations 2002.

➤ where this is necessary to ensure maintenance of control measures or the protection of health

341

Introduction to Health and Safety at Work ➤ speciﬁcally for vinyl chloride monomer or chromium plating as required by schedule 5 and ➤ keep a record of identiﬁable personal exposures for 40 years and any other exposures for 5 years.

17.12

Dangerous Substances and Explosive Atmospheres Regulations (DSEAR) 2002

17.11.9 Step 6 – health surveillance – Regulation 11 Employers must ensure employees, where appropriate, who are exposed or liable to be exposed, are under health surveillance. It is considered appropriate when: ➤ employee is exposed (if signiﬁcant) to substances or processes in schedule 6 ➤ an identiﬁable disease or adverse health effect may be related to the exposure, and there is a reasonable likelihood that disease may occur and there are valid disease indication or effect detection methods. Records of health surveillance containing approved particulars must be kept for 40 years or offered to HSE if trading ceases. If a person is exposed to a substance and/or process in schedule 6, the health surveillance shall include medical surveillance by an employment medical adviser or appointed doctor at intervals not exceeding 12 months. If a medical adviser certiﬁes that a person should not be engaged in particular work they must not be permitted to carry out that work except under speciﬁed conditions. Health records must be available for the individual employee to see after reasonable notice. Employees must present themselves, during working hours at the employer’s expense, for appropriate health surveillance. An employment medical adviser or appointed doctor has the power to inspect the workplace or look at records for the purpose of carrying out functions under COSHH.

17.11.10 Step 7 – information, instruction and training and emergencies – Regulation 12 and 13 Where employees are likely to be exposed to substances hazardous to health employers must provide: ➤ information, instruction and training on the risks to health and the precautions which should be taken (this duty is extended to anyone who may be affected) ➤ information on any monitoring of exposure (particularly if there is a workplace exposure limit where the employee or their representative must be informed immediately) ➤ information on collective results of health surveillance (designed so that individuals cannot be identiﬁed). ➤ Procedures for accidents and emergencies

342

17.11.11

Defence – Regulation 16

It is a defence under these regulations for a person to show that they have taken all reasonable precautions and exercised all due diligence to avoid the commission of an offence.

17.11.12

References

The Control of Substances Hazardous to Health Regulations 2002, SI 2002, 2677, 2002 Stationery Ofﬁce ISBN 0-11-042919-2 Control of substances hazardous to health Approved Code of Practice and Guidance L5 (5th Edition), 2005 HSE Books ISBN 0-7176-2981-3 COSHH: A brief guide to the Regulations, INDG136 (Rev3), HSE Books ISBN 0 7176 2982 1 COSHH Essentials: easy steps to control chemicals. HSG193 (2nd edition), 2003 HSE Books ISBN 0-7176-2737-3 EH40/2005 Workplace Exposure Limits HSE Books 2005 (revised annually) ISBN 0-7176-2977 5 Seven steps to successful substitution of hazardous substances. HSG110, 1994 HSE Books ISBN 0-7176-0695-3 Why do I need a safety data sheet? INDG353, 20002, HSE Books ISBN 0-7176-2367-X

17.12

Dangerous Substances and Explosive Atmospheres Regulations (DSEAR) 2002

17.12.1

Introduction

These Regulations are designed to implement the safety requirements of The EU Chemical Agents and Explosive Atmospheres Directives. DSEAR deals with the prevention of ﬁres, explosions and similar energy releasing events arising from dangerous substances. Following the introduction of DSEAR the opportunity will also be taken to modernize all the existing laws on the use and storage of petrol. In summary the DSEAR Regulations require employers and the self employed to: ➤ carry out an assessment of the ﬁre and explosion risks of any work activities involving dangerous substances ➤ provide measures to eliminate, or reduce as far as is reasonably practicable, the identiﬁed ﬁre and explosion risks

Summary of the main legal requirements ➤ apply measures, so far as is reasonably practicable, to control risks and to mitigate the detrimental effects of a ﬁre or explosion ➤ provide equipment and procedures to deal with accidents and emergencies, and ➤ provide employees with information and precautionary training. Where explosive atmospheres may occur: ➤ the workplaces should be classiﬁed into hazardous and non-hazardous places; and any hazardous places classiﬁed into zones on the basis of the frequency and duration of an explosive atmosphere, and where necessary marked with a sign ➤ equipment in classiﬁed zones should be safe so as to satisfy the requirements of the Equipment and Protective Systems Intended for Use in Potentially Explosive Atmospheres Regulations 1996, and ➤ the workplaces should be veriﬁed by a competent person, as meeting the requirements of DSEAR.

17.12.2

Scope of Regulations

Dangerous substance The regulations give a detailed interpretation of dangerous substance, which should be consulted. In summary it means: ➤ a substance or preparation that because of its chemical and sometimes physical properties and the way it is present and/or used at work, creates a ﬁre or explosion risk to people; for example, substances like petrol, LPG, paints, cleaners, solvents and ﬂammable gases ➤ any dusts which could form an explosive mixture in air (not included in a substance or preparation); for example, many dusts from grinding, milling or sanding.

Explosive atmosphere The Regulations give the deﬁnition as: a mixture under atmospheric conditions, of air and one or more dangerous substances in the form of gases, vapours, mists or dusts, in which, after ignition has occurred, combustion spreads to the entire unburned mixture.

17.12.3

Application

The Regulations do not in general apply to: ➤ ships under the control of a master, ➤ areas used for medical treatment of patients

➤ many gas appliances used for cooking, heating, hot water, refrigeration, etc. (except an appliance specifically designed for an industrial process), gas ﬁttings ➤ manufacture, use, transport of explosives or chemically unstable substances ➤ mine, quarry or borehole activities ➤ activity at an offshore installation ➤ the use of means of transport (but the Regulations do cover means of transport intended for use in a potentially explosive atmosphere).

17.12.4

Risk Assessment – Regulation 5

The risk assessment required by Regulation 5 must include: ➤ the hazardous properties of the dangerous substance ➤ suppliers information and safety data sheet ➤ the circumstances of the work including – ➤ work processes and substances used and their possible interactions ➤ the amount of substance involved ➤ risks of substances in combination ➤ arrangements for safe handling, storage and transport and any waste which might contain dangerous substances ➤ high risk maintenance activities ➤ likelihood of an explosive atmosphere ➤ likelihood of ignition sources, including electrostatic discharges being present ➤ scale of any possible ﬁre or explosion ➤ any places connected by openings to areas where there could be an explosive atmosphere ➤ any additional information which may be needed.

17.12.5

Elimination or reduction of risks – Regulation 6

Regulation 6 concerns the reduction of risks and tracks the normal hierarchy as follows: ➤ Substitution of a dangerous substance by a substance or process which eliminates or reduces the risk, for example the use of water based paints, or using a totally enclosed continuous process ➤ Reduce the quantity of dangerous substance to a minimum; for example, only a half day supply in the workroom ➤ Avoid releasing of a dangerous substance or minimize releases, for example keeping them in special closed containers ➤ Control releases at source ➤ Prevent the formation of explosive atmospheres, including the provision of sufﬁcient ventilation

343

Introduction to Health and Safety at Work ➤ Ensure that any releases are suitably collected, contained and removed; suitable local exhaust ventilation in a paint spray booth is an example ➤ Avoid ignition sources and adverse conditions, for example, keep electrical equipment outside the area ➤ Segregate incompatible dangerous substances, for example, oxidizing substances and other ﬂammable substances. Steps must also be taken to mitigate the detrimental effects of a ﬁre or explosion by: ➤ ➤ ➤ ➤ ➤

Keeping the number of people exposed to a minimum Avoidance of ﬁre and explosion propagation Provision of explosion relief systems Provision of explosion suppression equipment Provision of very strong plant which can withstand an explosion ➤ The provision of suitable personal protective equipment.

17.12.6 Classification of workplaces – Schedule 2 Where an explosive atmosphere may occur, work places must be classiﬁed into hazardous and non-hazardous places. Table 17.4 shows the zones speciﬁed by schedule 2 of the Regulations. Table 17.4

17.12.7

In addition to any normal ﬁre prevention requirements employers must under these Regulations ensure that: ➤ procedures and ﬁrst aid are in place with tested relevant safety drills ➤ provide information on emergency arrangements including work hazards and those that are likely to arise at the time of an accident ➤ provide suitable warning and other communications systems to enable an appropriate response, remedial actions and rescue operations to be made ➤ where necessary, before any explosion condition is reached provide visual or audible warnings and withdraw employees ➤ provide escape facilities where the risk assessment indicates it is necessary. In the event of an accident immediate steps must be taken to: ➤ mitigate the effects of the event ➤ restore the situation to normal, and ➤ inform employees who may be affected. Only essential persons may be permitted in the affected area. They must be provided with personal protective equipment, protective clothing and any necessary specialized safety equipment and plant.

Classification Zones

17.12.8 Zone 0

A place in which an explosive atmosphere consisting of a mixture with air of dangerous substances in the form of gas, vapour or mist is present continuously or for long periods.

Zone 1

A place in which an explosive atmosphere consisting of a mixture with air of dangerous substances in the form of gas, vapour or mist is likely to occur in normal operation occasionally.

Zone 2

A place in which an explosive atmosphere consisting of a mixture with air of dangerous substances in the form of gas, vapour or mist is not likely to occur in normal operation but, if it does, will persist for a short period only.

Zone 20

A place in which an explosive atmosphere in the form of a cloud of combustible dust in air is present continuously, or for long periods.

Zone 21

A place in which an explosive atmosphere in the form of a cloud of combustible dust in air is likely to occur in normal operation occasionally.

Zone 22

A place in which an explosive atmosphere in the form of a cloud of combustible dust in air is not likely to occur in normal operation but, if it does occur, will persist for a short period only.

344

Accidents, incidents and emergencies – Regulation 8

Information instruction and training – Regulation 9

Under Regulation 9 where a dangerous substance is present an employer must provide: ➤ suitable and sufﬁcient information, instruction and training on the appropriate precautions and actions ➤ plus details of the substances any relevant data sheets and legal provisions ➤ plus the signiﬁcant ﬁndings of the risk assessment.

17.12.9

Contents of containers and pipes – Regulation 10

Regulation 10 requires that for containers and pipes (except where they are marked under legislation contained in schedule 5 to the Regulations) the content and the nature of those contents and any associated hazards be clearly identiﬁed.

17.12.10

References

The Dangerous Substances and Explosive Atmosphere Regulations 2002 SI 2002 No 2776 ISBN 0-11-042957-5

Summary of the main legal requirements Fire and Explosions How safe is your workshop. A short guide to DSEAR, HSE INDG370 (rev1), 2002 HSE Books, ISBN 0-7176-2956 2 Safe use and handling of ﬂammable liquids HSG 140 HSE Books ISBN 0-7176-0967-7 Safe handling of combustible dusts; precautions against explosion HSG 103 HSE Books 1994 ISBN 0 7176 0725 9 Storage of dangerous substances, L135 Dangerous Substances and Explosive Atmospheres Regulations 2002. Approved Code of Practice and guidance First published 2003 HSE Books, ISBN 0 7176 2200 2 Control and mitigation measures, L136 Dangerous Substances and Explosive Atmospheres Regulations 2002 Approved Code of Practice and guidance, First published 2003 HSE Books, ISBN 0 7176 2201 0 Safe maintenance, repair and cleaning procedures, L137 Dangerous Substances and Explosive Atmospheres Regulations 2002 Approved Code of Practice and guidance, First published 2003 HSE Books, ISBN 0 7176 2202 9 Dangerous substances and explosive atmospheres, L138 Dangerous Substances and Explosive Atmospheres Regulations 2002 Approved Code of Practice, First published 2003 HSE Books ISBN 0 7176 2203 7

Work Regulations and the Provision and Use of Work Equipment Regulations.

17.13

Health and Safety (Display Screen Equipment) Regulations 1992

17.13.3

General

➤ ➤ ➤ ➤ ➤

(a) Display Screen Equipment (DSE) refers to any alphanumeric or graphic display screen, regardless of the display process involved (b) A user is an employee and an operator is a selfemployed person, both of whom habitually use display screen equipment as a signiﬁcant part of their normal work. Both would be people to whom most or all of the following apply. A person: ➤ who depends on the display screen equipment to do their job ➤ who has no discretion as to use or non-use ➤ who needs particular training and/or skills in the use of display screen equipment to do their job ➤ who uses display screen equipment for continuous spell of an hour or more at a time ➤ who does so on a more or less daily basis ➤ for whom fast transfer of data is important for the job ➤ of whom a high level of attention and concentration is required, in particular to prevent critical errors. (c) A workstation is an assembly comprising: ➤ display screen equipment with or without a keyboard, software or input device ➤ optional accessories ➤ disk drive, telephone, modem, printer, document holder, chair, desk, work surface, etc ➤ the immediate working environment.

Exemptions – Regulation 1(4)

Exemptions include display screen equipment used in connection with: drivers’ cabs or control cabs for vehicles or machinery on board a means of transport mainly intended for public operation portable systems not in prolonged use calculators, cash registers and small displays related to the direct use of this type of equipment ➤ window typewriters.

17.13.4

Assessment of risk – Regulation 2

Possible hazards associated with display screen equipment are physical (musculoskeletal) problems, visual fatigue and mental stress. They are not unique to display screen work, nor an inevitable consequence of it, and

345

Health and Safety (Display Screen Equipment) Regulations 1992

These Regulations cover the minimum health and safety requirements for the use of display screen equipment and are accompanied by a guidance note. They typically apply to computer equipment with either a cathode ray tube or liquid crystal monitors. But any type of display is covered with some exceptions, for example, on board a means of transport, or where the main purpose is for screening a ﬁlm or for a television. Multi-media equipment would generally be covered. Equipment not speciﬁcally covered by these Regulations or where it is not being used by a deﬁned ‘user’ are, nevertheless, covered by other requirements under the Management of Health and Safety at

Definitions – Regulation 1

17.13

17.13.1

17.13.2

Introduction to Health and Safety at Work indeed research shows that the risk to the individual from typical display screen work is low. However, as in other types of work, ill-health can result from poor work organization, working environment, job design and posture, and from inappropriate working methods. Employers must carry out a suitable and sufﬁcient analysis of users’ (regardless of who has provided them) and operators’ (provided by the employer) workstations in order to assess the risks to health and safety. The guidance gives detailed information on workstation minimum standards and possible effects on health. The assessment should be reviewed when major changes are made to software, hardware, furniture, environment or work requirements.

The employer must provide a further eye and eyesight test at regular intervals thereafter or when a user is experiencing visual difﬁculties which could be caused by working with display screen equipment. There is no reliable evidence that work with display screen equipment causes any permanent damage to eyes or eyesight, but it may make users with pre-existing vision defects more aware of them. An eye and eyesight test means a sight test as deﬁned in the Opticians Act 1989. These should be carried out by a registered ophthalmic optician or medical practitioner (normally only those with an ophthalmic qualiﬁcation do so). Employers shall provide special corrective appliances to users where:

17.13.5

➤ normal corrective appliances cannot be used ➤ the result of the eye and eyesight test shows that such provision is necessary.

Workstations – Regulation 3

All workstations must meet the requirements laid down in the schedule to the regulations. This schedule lays down minimum requirements for display screen workstations, covering the equipment, the working environment, and the interface between computer and user/operator.

17.13.6 Daily work routine of users – Regulation 4 The activities of users should be organized so that their daily work on display screen equipment is periodically interrupted by breaks or changes of activity that reduce their workload at the equipment. In most tasks, natural breaks or pauses occur from time to time during the day. If such breaks do not occur, deliberate breaks or pauses must be introduced. The guidance requires that breaks should be taken before the onset of fatigue and must be included in the working time. Short breaks are better than occasional long ones, for example, a 5–10 minute break after 50–60 minutes continuous screen and/or keyboard work is likely to be better than a 15-minute break every two hours. If possible, breaks should be taken away from the screen. Informal breaks, with time on other tasks, appear to be more effective in relieving visual fatigue than formal rest breaks.

17.13.7

17.13.8

Training – Regulation 6

Employers shall ensure that adequate health and safety training is provided to users and potential users in the use of any workstation and refresh the training following any re-organization. The guidance suggests a range of topics to be covered in the training. In summary these involve:

Eyes and eyesight – Regulation 5

Initially on request, employees have the right to a free eye and eyesight test conducted by a competent person where they are: ➤ already users (as soon as practicable after the request) ➤ to become a user (before they become a user).

346

The guidance indicates that the liability of the employer extends only to the provision of corrective appliances, which are of a style and quality adequate for its function. If an employee chooses a more expensive design or multi-function correction appliances, the employer need only pay a proportion of the cost. Employers are free to specify that users’ eye and eyesight tests and correction appliances are provided by a nominated company or optician. The conﬁdential clinical information from the tests can only be supplied to the employer with the employee’s consent. Vision screen tests can be used to identify people with defects but they are not a substitute for the full eyesight test and employees have the right to opt for the full test from the outset.

➤ the recognition of hazards and risks, including the absence of desirable features and the presence of undesirable ones ➤ causes of risk and how harm may occur ➤ what the user can do to correct them ➤ how problems can be communicated to management ➤ information on the regulations ➤ the user’s contribution to assessments.

Summary of the main legal requirements Table 17.5

Provision of information under Regulation 7 Information on

Does employer have to provide information to display screen workers who are:

Risks from DSE and workstation

Risk assessment and measures to reduce the risks Reg 2 & 3

Breaks and activity changes Reg 4

Eye and eyesight tests Reg 5

Initial training Reg 6(1)

Training when workstation modified Reg 6(2)

Users employed by the undertaking

Yes

Yes

Yes

Yes

Yes

Yes

Users employed by other employer

Yes

Yes

Yes

No

No

Yes

Operators in the undertaking

Yes

Yes

No

No

No

No

Reproduced from Introduction to Health and Safety in Construction, Butterworth-Heinemann, ISBN 075068111X

17.13.9

Information – Regulation 7

17.13.10

injury from electricity in work activities. The regulations impose duties on persons (‘duty holders’) in respect of systems, electrical equipment and conductors and in respect of work activities on or near electrical equipment. They apply to almost all places of work and electrical systems at all voltages. Guidance on the Regulations is contained in the Memorandum of Guidance on the Electricity at Work Regulations 1989, published by the HSE.

References 17.14.1

Work with display screen equipment, Health and Safety (Display Screen Equipment) Regulations 1992 as amended by the Health and Safety (Miscellaneous Amendments) Regulations 2002 Guidance on Regulations L26 2nd edition 2003, HSE Books ISBN 0-7176-2582-6 The law on VDU’s: An Easy Guide, HSG90, 2002 HSE Books ISBN 0-7176-2602-4 Working with VDU’s INDG 36 (rev1) 1998 HSE Books ISBN 0-7176-1504-9 VDU workstation checklist 2003 HSE Books ISBN 0-7176-2617-2

17.14

Electricity at Work Regulations 1989

The purpose of these Regulations is to require precautions to be taken against the risk of death or personal

Definitions

(a) Electrical equipment – includes anything used to generate, provide, transmit, rectify, convert, conduct, distribute, control, store, measure or use electrical energy. (b) Conductor – means a conductor of electrical energy. It means any material (solid liquid or gas), capable of conducting electricity. (c) System – means an electrical system in which all the electrical equipment is, or may be, electrically connected to a common source of electrical energy, and includes the source and equipment. It includes portable generators and systems on vehicles. (d) Circuit conductor – term used in Regulations 8 and 9 only, means a conductor in a system which is intended to carry electric current in normal conditions. It would include a combined neutral and earth conductor, but does not include a conductor provided solely to perform a protective connection to earth or other reference point and energized only during abnormal conditions.

347

17.14 Electricity at Work Regulations 1989

Operators and users shall be provided with adequate information on all aspects of health and safety relating to their workstation and what steps the employer has taken to comply with the Regulations (insofar as the action taken relates to that operator or user and their work). Under Regulation 7 speciﬁc information should be provided as outlined in Table 17.5.

Introduction to Health and Safety at Work (e) Danger – in the context of these Regulations means a risk of injury from any electrical hazard.

17.14.5

Adverse or hazardous environments – Regulation 6

Electrical equipment which may be exposed to: Every year about 30 people die from electric shock or electric burns at work. Each year several hundred serious burns are caused by arcing when the heat generated can be very intense. In addition, intense ultraviolet radiation from an electric arc can cause damage to the eyes – known as arc-eye. These hazards are all included in the deﬁnition of Danger.

➤ mechanical damage ➤ the effects of weather, natural hazards, temperature or pressure ➤ the effects of wet, dirty, dusty or corrosive conditions ➤ any ﬂammable or explosive substances including dusts, vapours or gases

17.14.2

shall be so constructed and protected that it prevents danger.

Duties – Regulation 3

Duties are imposed on employers, self-employed and employees. The particular duties on employees are intended to emphasize the level of responsibility which many employees in the electrical trades and professions are expected to take on as part of their job. They are: ➤ to co-operate with their employer so far as is necessary to enable any duty placed on the employer to be complied with (this reiterates section 7 (b) of the HSW Act) ➤ to comply with the provisions of these Regulations in so far as they relate to matters which are within their control. (This is equivalent to duties placed on employers and self-employed where these matters are within their control.)

17.14.3 Systems, work activities and protective equipment – Regulation 4 Systems must, at all times, be of such construction as to prevent danger. Construction covers the physical condition, arrangement of components and design of the system and equipment. All systems must be maintained so as to prevent danger. Every work activity, including operation, use and maintenance or work near a system shall be carried out in a way, which prevents danger. Protective equipment shall be suitable, suitably maintained and used properly.

17.14.4 Strength and capability of equipment – Regulation 5

17.14.6

All conductors in a system which may give rise to danger shall either be suitably covered with insulating material and further protected as necessary, for example, against mechanical damage, using trunking or sheathing; or have precautions taken that will prevent danger, for example, being suitably placed like overhead electric power cables, or by having strictly controlled working practices.

17.14.7

348

Earthing, integrity and other suitable precautions – Regulation 8

Precautions shall be taken, either by earthing or by other suitable means, for example, double insulation, use of safe voltages and earth-free non-conducting environments, where a conductor, other than a circuit conductor, could become charged as a result of either the use of, or a fault in, a system. An earth conductor shall be of sufﬁcient strength and capability to discharge electrical energy to earth. The conductive part of equipment, which is not normally live but energized in a fault condition, could be a conductor. If a circuit conductor is connected to earth or to any other reference point nothing which could break electrical continuity or introduce high impedance, for example, fuse, thyristor or transistor, is allowed in the conductor unless suitable precautions are taken. Permitted devices would include a joint or bolted link, but not a removable link or manually operated knife switch without bonding of all exposed metal work and multiple earthing.

17.14.8 No electrical equipment may be put into use where its strength and capability may be exceeded in such a way as may give rise to danger, in normal transient or fault conditions.

Insulation, protection and placing of conductors – Regulation 7

Connections – Regulation 10

Every joint and connection in a system shall be mechanically and electrically suitable for its use. This includes terminals, plugs and sockets.

Summary of the main legal requirements 17.14.9 Excess current protection – Regulation 11 Every part of a system shall be protected from excess current, for example, short circuit or overload, by a suitably located efﬁcient means such as a fuse or circuit breaker.

17.14.10 Cutting off supply and isolation – Regulation 12

Adequate precautions shall be taken to prevent electrical equipment that has been made dead from becoming live while work is carried out on or near the equipment. This will include means of locking off isolators, tagging equipment, permits to work and removing fuses.

17.14.12 Work on or near live conductors – Regulation 14 No person shall work near a live conductor, except if it is insulated, unless: ➤ it is unreasonable in all the circumstances for it to be dead ➤ it is reasonable in all the circumstances for them to be at work on or near it while it is live ➤ suitable precautions (including where necessary the provision of suitable protective equipment) are taken to prevent injury.

17.14.13 Working space access and lighting – Regulation 15 Adequate working space means of access and lighting shall be provided for all electrical equipment at which or near which work is being done in circumstances which may give rise to danger. This covers work of any kind. However, when the work is on live conductors the access space must be sufﬁcient for a person to fall back out of

Competence – Regulation 16

Where technical knowledge or experience is necessary to prevent danger, all persons must possess such knowledge or experience or be under appropriate supervision.

17.14.15

References

Memorandum of guidance on the Electricity at Work Regulations, Guidance on Regulations, HSR25, 1989 HSE Books ISBN 0-7176-1602-9 Electricity at Work: safe working practices,HSG85 2003 HSE Books ISBN 0-7176-2164-2 Maintaining portable and transportable electrical equipment, HSG107 1994 HSE Books ISBN 0-7176-0715-1 Electrical safety and you, INDG231, 1996 HSE Book ISBN 0-7176-1207-4 Maintaining portable electrical equipment in ofﬁces and other low-risk environments, INDG236, 1996 HSE Books ISBN 0-7176-1272-4 Maintaining portable electrical equipment in hotels and tourist accommodation, INDG237, 1997 HSE Books ISBN 0-7176-1273-2 Safety in electrical testing at work, General Guidance INDG354 2003 HSE Books ISBN 0-7176-2296-7 Electrical switch gear and safety. A concise guide for users INDG372, HSE Books, 2003 ISBN 0 7176 2187 1

17.15

Employers’ Liability (Compulsory Insurance) Act 1969 and Regulations 1998

17.15.1

Introduction

Employers are responsible for the health and safety of employees while they are at work. Employees may be injured at work, or they or former employees may become ill as a result of their work while employed. They may try to claim compensation from the employer if they believe them to be responsible. The Employers’ Liability Compulsory Insurance Act 1969 ensures that an employer has at least a minimum level of insurance cover against any such claims. Employers’ liability insurance will enable employers to meet the cost of compensation for employees’ injuries or

349

Employers’ Liability (Compulsory Insurance) Act 1969 and Regulations 1998

17.14.11 Work on equipment made dead – Regulation 13

17.14.14

17.15

There should be suitably located and identiﬁed means of cutting off (switch) the supply of electricity to any electrical equipment and also isolating any electrical equipment. Although these are separate requirements, they could be affected by a single means. The isolator should be capable of being locked off to allow maintenance to be done safely. Sources of electrical energy (accumulators, capacitors and generators) are exempt from this requirement, but precautions must be taken to prevent danger.

danger and if needed for persons to pass one another with ease and without hazard.

Introduction to Health and Safety at Work illnesses whether they are caused on or off site. However, any injuries or illnesses relating to motor accidents that occur while employees are working for them, may be covered separately by motor insurance. Public liability insurance is different. It covers for claims made against a person/company by members of the public or other businesses, but not for claims made by employees. While public liability insurance is generally voluntary, employers’ liability insurance is compulsory. Employers can be ﬁned if they do not hold a current employers’ liability insurance policy which complies with the law.

17.15.2

Application

An employer needs employers’ liability insurance unless they are exempt from the Employers’ Liability Compulsory Insurance Act. The following employers are exempt: ➤ most public organizations including government departments and agencies, local authorities, police authorities and nationalized industries ➤ health service bodies, including National Health Service trusts, health authorities, Family Health Services Authorities and Scottish Health Boards and State Hospital Management Committees ➤ some other organizations which are ﬁnanced through public funds, such as passenger transport executives and magistrates’ courts committees ➤ family businesses, i.e. if employees are closely related to the employer (as husband, wife, father, mother, grandfather, grandmother, stepfather, stepmother, son, daughter, grandson, granddaughter, stepson, stepdaughter, brother, sister, half-brother or half-sister). However, this exemption does not apply to family businesses that are incorporated as limited companies. A full list of employers who are exempt from the need to have employers’ liability insurance is shown at Schedule 2 of the Employers’ Liability (Compulsory Insurance) Regulations 1998.

17.15.3

Coverage

Employers are only required by law to have employers’ liability insurance for people whom they employ. However, people who are normally thought of as selfemployed may be considered to be employees for the purposes of employers’ liability insurance. Whether or not an employer needs employers’ liability insurance for someone who works for them depends on the terms of the contract. This contract can be spoken, written or implied. It does not matter whether someone is

350

usually called an employee or self-employed or what their tax status is. Whether the contract is called a contract of employment or a contract for services is largely irrelevant. What matters is the real nature of the employer/employee relationship and the degree of control the employer has over the work they do. There are no hard and fast rules about who counts as employee for the purposes of Employers’ liability insurance. The following paragraphs may help to give some indication. In general, employers’ liability insurance may be needed for a worker if: ➤ national insurance and income tax is deducted from the money paid to them ➤ the employer has the right to control where and when they work and how they do it ➤ most materials and equipment are supplied by the employer ➤ the employer has a right to any proﬁt workers make even though the employer may choose to share this with them through commission, performance pay or shares in the company. Similarly, the employer will be responsible for any losses ➤ that person is required to deliver the service personally and they cannot employ a substitute if they are unable to do the work ➤ they are treated in the same way as other employees, for example, if they do the same work under the same conditions as some other employee. In most cases employers’ liability insurance is needed for volunteers. Although, in general, the law may not require an employer to have insurance for: ➤ students who work unpaid ➤ people who are not employed but are taking part in youth or adult training programmes ➤ schoolchildren on work experience programmes. However, in certain cases, these groups might be classed as employees. In practice, many insurance companies will provide cover for people in these situations. One difﬁcult area is domestic help. In general, an employer will probably not need employers’ liability insurance for people such as cleaners or gardeners if they work for more than one person. However, if they only work for one employer, that employer may be required to take out insurance to protect them.

17.15.4

Display of certificate

Under the regulations, employers must display in a suitable convenient location, a current copy of the certiﬁcate of insurance at each place of business where they employ relevant people.

Summary of the main legal requirements 17.15.5

Retention of certificates

An employer must retain for at least 40 years copies of certiﬁcates of insurance which have expired. This is because claims for diseases can be made many years after the disease is caused. Copies can be kept electronically if this is more convenient than paper. An employer must make these available to health and safety inspectors on request. These requirements do not apply to policies which expired before 1 January 1999. However, it is still very important to keep full records of previous insurance policies for the employer’s own protection.

17.15.6

Penalties

17.16

Regulatory Reform (Fire Safety) Order 2005

17.16.1

Introduction

This Order, made under the Regulatory Reform Act 2001, reforms the law relating to ﬁre safety in non-domestic premises. It replaces ﬁre certiﬁcation under the Fire Precautions Act 1971 (which it repeals) with a general duty to ensure, so far as is reasonably practicable, the safety of employees, a general duty, in relation to non-employees to take such ﬁre precautions as may reasonably be required in the circumstances to ensure that premises are safe and a duty to carry out a risk assessment. The Fire Certiﬁcate (Special premises) Regulations 1976, The Fire Precautions (Workplace) Regulations 1997 and amendment Regulations 1999 are all revoked. The Fire Safety Order is the responsibility of the Department for Communities and Local Government and is enforced by the local ﬁre and rescue authorities, with some exceptions which include: ➤ the HSE for: ➤ Nuclear Installations ➤ Ships in construction or repair, and ➤ Construction sites other than a construction site which is contained within, or forms part of,

The order came into force on 1 October 2006 with a number of guidance documents. In Scotland the Fire Safety legislation is enacted through the Fire (Scotland) Act 2005 which in brief covers the following. The Fire (Scotland) Act 2005 received Royal Assent on 1 April 2005. Parts 1, 2, 4 and 5 of the Act commenced in August 2005. Part 3 introduces a new ﬁre safety regime for non-domestic premises and is due to come into force on 1 October 2006 and will replace the Fire Precautions Act 1971 and the Fire Precautions (Workplace) Regulations 1997, as amended. Fire certiﬁcates will no longer be required after 1 October 2006 and the new ﬁre safety regime will be based on the principle of risk assessment (similar to the Fire Precautions (Workplace) Regulations). Fire safety regulations are currently being prepared which will contain detailed provisions in respect of ﬁre safety risk assessments and ﬁre safety measures. These regulations came into force on 1 October 2006. Ten guidance documents to complement the new legislation and help those with ﬁre safety responsibilities to understand their duties are available. A guidance booklet, which is applicable to all premises, regardless of the size and activities undertaken on the premises, is available, free of charge, from Blackwell’s Bookshop, 53 South Bridge, Edinburgh. Local ﬁre and rescue authorities also have a supply of the booklets and may be able to assist with any requests for additional copies (check the phonebook for contact details). The guidance booklet is available for downloading from a new website dedicated to the new ﬁre safety regime which can be accessed at www.infoscotland.com/ ﬁrelaw. The website includes a facility for signing up to receive e-mail updates on progress with the new legislation and the availability of guidance documents. If there are any queries about the new ﬁre safety legislation, publicity campaign or guidance documents, contact the Justice Department Fire Branch on 0131 244 5338 or 0131 244 2784. Alternatively send an e-mail to [email protected].

PART 1 General 17.16.2

Interpretation – Articles 1–7

Here are a few of the more important deﬁnitions from the articles. For a full list consult the Order directly.

351

17.16 Regulatory Reform (Fire Safety) Order 2005

The Health and Safety Executive enforces the law on employers’ liability insurance and HSE inspectors will check that employers have employers’ liability insurance with an approved insurer for at least £5m. They will ask to see the certiﬁcate of insurance and other insurance details. Employers can be ﬁned up to £2500 for any day they are without suitable insurance. If they do not display the certiﬁcate of insurance or refuse to make it available to HSE inspectors when they ask, employers can be ﬁned up to £1000.

premises which are occupied by persons other than those carrying out the construction work or any activity arising from such work. ➤ In Crown occupied and Crown owned buildings enforcement is carried out by the Fire Services Inspectorates appointed under the Fire Services Act 1947 ➤ Local Authorities for Certiﬁcated Sports Grounds.

Introduction to Health and Safety at Work a) ‘Premises’ includes any place and, in particular, includes:

These issues do not cover process related ﬁre risks including:

➤ Any workplace ➤ Any vehicle, vessel, aircraft or hovercraft ➤ Any installation on land (including the foreshore and other land intermittently covered by water), and any other installation (whether ﬂoating, or resting on the seabed or the subsoil thereof, or resting on other land covered with water or the subsoil thereof) ➤ Any tent or movable structure.

➤ the use of plant or machinery, or ➤ the use or storage of any dangerous substance.

b) ‘Risk’ means the risks to the safety of persons from ﬁre. ‘Safety’ means the safety of persons in the event of ﬁre. ‘Workplace’ means any premises or parts of premises, not being domestic premises, used for the purposes of an employer’s undertaking and which are made available to an employee of the employer as a place of work and includes: ➤ Any place within the premises to which such employee has access while at work, and ➤ Any room, lobby, corridor, staircase, road, or other place: ➤ Used as a means of access to or egress from that place of work, or ➤ Where facilities are provided for use in connection with that place of work, other than a public road. c) ‘Responsible Person’ means: ➤ In relation to a workplace, the employer, if the workplace is to any extent under their control ➤ In relation to any premise not falling within paragraph (a): ➤ The person who has control of the premises (as occupier or otherwise) in connection with the carrying on by them of a trade, business or other undertaking (for proﬁt or not), or ➤ The owner, where the person in control of the premises does not have control in connection with the carrying on by that person of a trade, business or other undertaking. d) ‘General ﬁre precautions’ in relation to premises means: ➤ measures to reduce the risk of ﬁre and the risk of the spread of ﬁre ➤ the means of escape from the premises ➤ measures for securing that, at all material times, the means of escape can be safely and effectively used ➤ measures in relation to ﬁghting ﬁres ➤ the means for detecting ﬁres and giving warning in case of ﬁre ➤ action to be taken in the event of ﬁre, including ➤ instruction and training of employees ➤ measures to mitigate the effects of the ﬁre.

352

Duties are placed on responsible persons in a workplace and in premises which are not work-places to the extent that they have control over the premises. The order does not apply (Article 8) to: ➤ domestic premises ➤ an offshore installation ➤ a ship, in respect of the normal ship-board activities of a ship’s crew which are carried out solely by the crew under the direction of the master ➤ ﬁelds, woods or other land forming part of an agricultural or forestry undertaking but which is not inside a building and is situated away from the undertaking’s main buildings ➤ an aircraft, locomotive or rolling stock, trailer or semitrailer used as a means of transport or a vehicle ➤ a mine other than any building on the surface at a mine ➤ a borehole site. In addition certain provisions of the Order do not apply to groups of workers such as: ➤ occasional work which is not harmful to young people in a family undertaking ➤ armed forces ➤ members of police forces ➤ emergency services PART 2 Fire Safety Duties

17.16.3

Duty to take general fire precautions Article 8

The responsible person must: (a) take such general ﬁre precautions as will ensure, so far as is reasonably practicable, the safety of any of his employees, and (b) in relation to relevant persons who are not their employees, take such general ﬁre precautions as may reasonably be required in the circumstances of the case to ensure that the premises are safe.

17.16.4

Risk assessment and Fire safety arrangements – Articles 9 and 11

The responsible person must make a suitable and sufﬁcient assessment of the risks to identify the general ﬁre precautions needs to take.

Summary of the main legal requirements MATTERS TO BE CONSIDERED IN RISK ASSESSMENT IN RESPECT OF DANGEROUS SUBSTANCES The matters are: (a) the hazardous properties of the substance; (b) information on safety provided by the supplier, including information contained in any relevant safety data sheet; (c) the circumstances of the work including: (i) the special, technical and organisational measures and the substances used and their possible interactions; (ii) the amount of the substance involved; (iii) where the work will involve more than one dangerous substance, the risk presented by such substances in combination; and (iv) the arrangements for the safe handling, storage and transport of dangerous substances and of waste containing dangerous substances; (d) activities, such as maintenance, where there is the potential for a high level of risk; (e) the effect of measures which have been or will be taken pursuant to this Order; (f) the likelihood that an explosive atmosphere will occur and its persistence; (g) the likelihood that ignition sources, including electrostatic discharges, will be present and become active and effective; (h) the scale of the anticipated effects; (i) any places which are, or can be connected via openings to, places in which explosive atmospheres may occur; and (j) such additional safety information as the responsible person may need in order to complete the assessment.

As soon as practicable after the assessment is made or reviewed, the responsible person must record the information prescribed where: (a) the employs ﬁve or more employees (b) a licence under an enactment is in force in relation to the premises, or (c) an Alterations Notice requiring this is in force in relation to the premises. The prescribed information is: (a) the signiﬁcant ﬁndings of the assessment, including the measures which have been or will be taken by the responsible person, and (b) any group of persons identiﬁed by the assessment as being especially at risk. The responsible person must make and record (as per risk assessments) arrangements as are appropriate, for the effective planning, organization, control, monitoring and review of the preventive and protective measures.

17.16.5

Figure 17.4 Where a dangerous substance is or is liable to be present in or on the premises, the risk assessment must include consideration of the matters set out in Part 1 of Schedule 1, reproduced in Figure 17.4. Risk assessments must be reviewed by the responsible person regularly and if it is no longer valid or there has been signiﬁcant changes. The responsible person must not employ a young person unless risks to young persons have been considered in an assessment covering the following which is Part 2 of Schedule 1.

Matters to be taken into particular account in risk assessment in respect of young persons The matters are: (a) the inexperience, lack of awareness of risks and immaturity of young persons (b) the ﬁtting-out and layout of the premises (c) the nature, degree and duration of exposure to physical and chemical agents (d) the form, range, and use of work equipment and the way in which it is handled (e) the organization of processes and activities (f) the extent of the safety training provided or to be provided to young persons, and (g) risks from agents, processes and work listed in the Annex to Council Directive 94/33/EC (a) on the protection of young people at work.

Principles of prevention to be applied and Fire safety arrangements Articles 10 and 11

Preventive and protective measures must be implemented on the basis of the principles speciﬁed in Part 3 of Schedule 1 as follows which broadly the same as those in the Management Regulations.

Principles of prevention The principles are: (a) (b) (c) (d) (e)

avoiding risks evaluating the risks which cannot be avoided combating the risks at source adapting to technical progress replacing the dangerous by the non-dangerous or less dangerous (f) developing a coherent overall prevention policy which covers technology, organization of work and the inﬂuence of factors relating to the working environment (g) giving collective protective measures priority over individual protective measures, and (h) giving appropriate instructions to employees. Fire Safety arrangements must be made and put into effect by the responsible person where ﬁve or more people are employed, there is a licence for the premises or an Alterations Notice requires them to be recorded. The arrangements must cover effective planning, organization, control, monitoring and review of the preventative and protective measures.

353

Introduction to Health and Safety at Work 17.16.6 Elimination or reduction of risks from dangerous substances – Article 12 Where a dangerous substance is present in or on the premises, the responsible person must ensure that risk of the substance is either eliminated or reduced so far as is reasonably practicable, by ﬁrstly replacing the dangerous substance with a safer alternative. Where it is not reasonably practicable to eliminate risk the responsible person must, so far as is reasonably practicable, apply measures including the measures speciﬁed in Part 4 of Schedule 1 to the Order (Figure 17.5). The responsible person must: (a) arrange for the safe handling, storage and transport of dangerous substances and waste containing dangerous substances, and (b) ensure that any conditions necessary for ensuring the elimination or reduction of risk are maintained.

17.16.7 Fire-fighting and fire detection Article 13 The premises must be equipped with appropriate ﬁreﬁghting equipment and with ﬁre detectors and alarms; Any non-automatic ﬁre-ﬁghting equipment provided must be easily accessible, simple to use and indicated by signs. Appropriate measures must be taken for ﬁre-ﬁghting in the premises: to nominate and train competent persons to implement the measures; arrange any necessary contacts with external emergency services. A person is to be regarded as competent where they has sufﬁcient training and experience or knowledge and other qualities to enable them to properly implement the measures referred to.

17.16.8 Emergency routes and exits – Article 14 Where necessary routes to emergency exits from premises and the exits themselves must be kept clear at all times. The following requirements must be complied with: (a) emergency routes and exits must lead as directly as possible to a place of safety (b) in the event of danger, it must be possible for persons to evacuate the premises as quickly and as safely as possible (c) the number, distribution and dimensions of emergency routes and exits must be adequate having regard to the use, equipment and dimensions of the premises and the maximum number of persons who may be present there at any one time

354

MEASURES TO BE TAKEN IN RESPECT OF DANGEROUS SUBSTANCES 1. In applying measures to control risks the responsible person must, in order of priority: (a) reduce the quantity of dangerous substances to a minimum; (b) avoid or minimize the release of a dangerous substance; (c) control the release of a dangerous substance at source; (d) prevent the formation of an explosive atmosphere, including the application of appropriate ventilation; (e) ensure that any release of a dangerous substance which may give rise to risk is suitably collected, safely contained, removed to a safe place, or otherwise rendered safe, as appropriate; (f) avoid: (i) ignition sources including electrostatic discharges; and (ii) such other adverse conditions as could result in harmful physical effects from a dangerous substance; and (g) segregate incompatible dangerous substances. 2. The responsible person must ensure that mitigation measures applied in accordance with article 12(3)(b) include: (a) reducing to a minimum the number of persons exposed; (b) measures to avoid the propagation of ﬁres or explosions; (c) providing explosion pressure relief arrangements; (d) providing explosion suppression equipment; (e) providing plant which is constructed so as to withstand the pressure likely to be produced by an explosion; and (f) providing suitable personal protective equipment. 3. The responsible person must: (a) ensure that the premises are designed, constructed and maintained so as to reduce risk; (b) ensure that suitable special, technical and organisational measures are designed, constructed, assembled, installed, provided and used so as to reduce risk; (c) ensure that special, technical and organisational measures are maintained in an efﬁcient state, in efﬁcient working order and in good repair; (d) ensure that equipment and protective systems meet the following requirements: (i) where power failure can give rise to the spread of additional risk, equipment and protective systems must be able to be maintained in a safe state of operation independently of the rest of the plant in the event of power failure; (ii) means for manual override must be possible, operated by employees competent to do so, for shutting down equipment and protective systems incorporated within automatic processes which deviate from the intended operating conditions, provided that the provision or use of such means does not compromise safety; (iii) on operation of emergency shutdown, accumulated energy must be dissipated as quickly and as safely as possible or isolated so that it no longer constitutes a hazard; and (iv) necessary measures must be taken to prevent confusion between connecting devices; (e) where the work is carried out in hazardous places or involves hazardous activities, ensure that appropriate systems of work are applied including: (i) the issuing of written instructions for the carrying out of work; and (ii) system of permits to work, with such permits being issued by a person with responsibility for this function prior to the commencement of the work concerned.

Figure 17.5

Summary of the main legal requirements (d) emergency doors must open in the direction of escape (e) sliding or revolving doors must not be used for exits speciﬁcally intended as emergency exits (f) emergency doors must not be so locked or fastened that they cannot be easily and immediately opened by any person who may require to use them in an emergency (g) emergency routes and exits must be indicated by signs, and (h) emergency routes and exits requiring illumination must be provided with emergency lighting of adequate intensity in the case of failure of their normal lighting.

17.16.9 Procedures for serious and imminent danger and for danger areas – Article 15 The responsible person must: (a) establish appropriate procedures, including safety drills (b) nominate a sufﬁcient number of competent persons to implement evacuation procedures (c) provide adequate safety instruction for restricted areas. Persons who are exposed to serious and imminent danger must be informed of the nature of the hazard and of the steps taken or to be taken to protect them from it. They must be able to stop work and immediately proceed to a place of safety in the event of their being exposed to serious, imminent and unavoidable danger; and procedures must require the persons concerned to be prevented from resuming work in any situation where there is still a serious and imminent danger.

including remedial actions and rescue operations, to be made immediately when such an event occurs (c) where necessary, before any explosion conditions are reached, visual or audible warnings are given and relevant persons withdrawn, and (d) where the risk assessment indicates it is necessary, escape facilities are provided and maintained to ensure that, in the event of danger, persons can leave endangered places promptly and safely. The information required must be: (a) made available to accident and emergency services, and (b) displayed at the premises, unless the results of the risk assessment make this unnecessary. In the event of a ﬁre arising from an accident, incident or emergency related to the presence of a dangerous substance in or on the premises, the responsible person must ensure that: (a) immediate steps are taken to: (i) mitigate the effects of the ﬁre (ii) restore the situation to normal, and (iii) inform those persons who may be affected. (b) only those persons who are essential for the carrying out of repairs and other necessary work are permitted in the affected area and they are provided with: (i) appropriate personal protective equipment and protective clothing, and (ii) any necessary specialized safety equipment and plant which must be used until the situation is restored to normal.

17.16.10 Additional emergency measures in respect of dangerous substances – Article 16

17.16.11

In order to safeguard persons from an accident, incident or emergency related to the presence of a dangerous substance the responsible person must (unless the risk assessment shows it is unnecessary) ensure that:

Any facilities, equipment and devices provided must be subject to a suitable system of maintenance and maintained in an efﬁcient state, in efﬁcient working order and in good repair.

(a) information on emergency arrangements is available, including: (i) details of relevant work hazards and hazard identiﬁcation arrangements, and (ii) speciﬁc hazards likely to arise at the time of an accident, incident or emergency (b) suitable warning and other communication systems are established to enable an appropriate response,

17.16.12

Maintenance – Article 17

Safety assistance – Article 18

The responsible person must, (except a competent self employed person) appoint one or more competent persons to assist them in undertaking the preventive and protective measures. If more than one person is appointed, they must make arrangements for ensuring adequate co-operation between them.

355

Introduction to Health and Safety at Work The number of persons appointed, the time available for them to fulﬁl their functions and the means at their disposal must be adequate having regard to the size of the premises, the risks to which relevant persons are exposed and the distribution of those risks throughout the premises.

17.16.13 Provision of information to employees and others – Article 19 and 20 The responsible person must provide their employees with comprehensible and relevant information on: ➤ ➤ ➤ ➤

the risks to them identiﬁed by the risk assessment the preventive and protective measures the procedures for ﬁre drills the identities of persons nominated for ﬁre ﬁghting or ﬁre drills ➤ the risks notiﬁed to them regarding shared premises. Before employing a child, a parent (or guardian) of the child must be provided with comprehensible and relevant information on the risks to that child identiﬁed by the risk assessment; the preventive and protective measures; and the risks notiﬁed to them regarding shared premises. Where a dangerous substance is present in or on the premises, additional information must be provided for employees as follows: (a) the details of any such substance including: (i) the name of the substance and the risk which it presents (ii) access to any relevant safety data sheet, and (iii) legislative provisions which apply to the substance. (b) the signiﬁcant ﬁndings of the risk assessment. The responsible person must ensure that the employer of any employees from an outside undertaking who are working in or on the premises is provided with comprehensible and relevant information on: (a) the risks to those employees, and (b) the preventive and protective measures taken by the responsible person. The responsible person must ensure that any person working in their undertaking who is not their employee is provided with appropriate instructions and comprehensible and relevant information regarding any risks to that person.

356

17.16.14

Capabilities and training – Article 21

The responsible person must ensure that all employees are provided with adequate safety training: (a) at the time when they are ﬁrst employed, and (b) on their being exposed to new or increased risks because of: (i) their being transferred or given a change of responsibilities (ii) the introduction of new work equipment into, or a change respecting work equipment already in use (iii) the introduction of new technology, or (iv) the introduction of a new system of work, or a change respecting a system of work already in use. The training must: (a) include suitable and sufﬁcient instruction and training on the appropriate precautions and actions to be taken by the employee (b) be repeated periodically where appropriate (c) be adapted to take account of any new or changed risks to the safety of the employees concerned (d) be provided in a manner appropriate to the risk identiﬁed by the risk assessment, and (e) take place during working hours.

17.16.15

Co-operation and co-ordination – Article 22

➤ Where two or more responsible persons share, or have duties in respect of, premises (whether on a temporary or a permanent basis) each such person must co-operate with, coordinate safety measures and inform the other responsible person concerned so far as is necessary to enable them to comply with the requirements and prohibitions imposed on them. ➤ Where two or more responsible persons share premises (whether on a temporary or a permanent basis) where an explosive atmosphere may occur, the responsible person who has overall responsibility for the premises must co-ordinate the implementation of all the measures required.

17.16.16

General duties of employees at work – Article 23

Every employee must, while at work: (a) take reasonable care for the safety of him or herself and of other relevant persons who may be affected by acts or omissions at work

Summary of the main legal requirements (b) as regards any duty or requirement imposed on an employer by or under any provision of this Order, the employee must co-operate so far as is necessary to enable that duty or requirement to be performed or complied with; and (c) inform their employer or any other employee with speciﬁc responsibility for the safety of fellow employees: (i) of any work situation which a person with the ﬁrst-mentioned employee’s training and instruction would reasonably consider represented a serious and immediate danger to safety, and (ii) of any matter which a person with the ﬁrstmentioned employee’s training and instruction would reasonably consider represented a shortcoming in the employer’s protection arrangements for safety.

17.16.17

Part 3 Enforcement Articles 25–31

Part 3 of the order is about enforcement and penalties. An enforcing authority may be the ﬁre and rescue authority of the area (most cases), the HSE (Nuclear sites, ships and construction sites without other operations) and Fire Inspectors maintained by the Secretary of State (armed forces, UK Atomic Energy Authority and Crown premises). Fire Inspectors and an ofﬁcer of the ﬁre brigade maintained by the ﬁre and rescue authority, ofﬁcers have similar powers (Articles 27 & 28) to inspectors under the HSW Act. There are differences between the HSW Act and the Fire order in the notices which can be issued. Appeals can be made against these notices within 21 days and the notices are suspended until the appeal is heard. However a Prohibition notice stands until conﬁrmed or altered by the court. Fire Inspectors can issue:

Alterations Notices – Article 29 These may be issued where the premises concerned constitute a serious risk to relevant people or may constitute a serious risk if any change is made to the premises or its use. Where an Alterations Notice has been served the responsible person must notify the enforcing authority before making any speciﬁed changes which are as follows: ➤ a change to the premises ➤ a change to the services, ﬁttings or equipment in or on the premises ➤ an increase in the quantities of dangerous substances which are present in or on the premises ➤ a change in the use of the premises.

In addition, the Alterations Notice may also include the requirement for the responsible person to: ➤ record the signiﬁcant ﬁndings of the risk assessment as per Article 9 (7) and 9 (6) ➤ record the ﬁre safety arrangements as per Article 11 (1) and 11 (2) ➤ before making the above changes to send to the enforcing authority a copy of the risk assessment and a summary of the proposed changes to the general ﬁre precautions.

Enforcement Notices – Article 30 Where the enforcing authority is of the opinion that the responsible person has failed to comply with the requirements of this Order or any regulations made under it they can issue an Enforcement Notice which must: ➤ state that the enforcing authority is of this opinion ➤ specify the provisions which have not been complied with; require that person to take steps to remedy the failure within a period (not less than 28 days) from the date of service of the notice. An Enforcement Notice may include directions on the measures needed to remedy the failures. Choices of remedial action must be left open. Before issuing an Enforcement Notice the enforcing authority must consult the relevant enforcing authorities including those under HSW Act and the Building Regulations.

Prohibition Notices – Article 31 If the enforcing authority is of the opinion that the risks, relating to escape from the premises, are so serious that the use of the premises ought to be prohibited or restricted they may issue a Prohibition Notice. The notice must: ➤ state that the enforcing authority is of this opinion ➤ specify the provisions which give or may give rise to that risk, and ➤ direct that the use to which the notice relates is prohibited or restricted as may be speciﬁed until the speciﬁed matters have been remedied. A Prohibition Notice may include directions on the measures needed to remedy the failures. Choices of remedial action must be left open. A Prohibition Notice takes effect immediately it is served.

17.16.18

Part 4 Offences and Appeals Articles 32–36

Cases can be tried in a magistrates’ court or on indictment in the Crown Court.

357

Introduction to Health and Safety at Work The responsible person can be on liable on conviction on indictment to a ﬁne (not limited), or to imprisonment for a term not exceeding two years or both. Any person can be liable to:

➤ treatment of minor injuries which would otherwise receive no treatment or which do not need treatment by a medical practitioner or nurse.

➤ on conviction on indictment to a ﬁne (not limited) for an offence where that failure places one or more relevant people at risk of death or serious injury in case of ﬁre ➤ on summary conviction to a ﬁne at standard levels 3 or 5 depending on the particular offence.

17.17.1

In general, where an offence is committed by a body corporate is proved to have been committed with the consent or connivance of any director, manager, secretary or other similar ofﬁcer of the body corporate they as well as the body corporate is guilty of that offence, Article 32 (9).

17.17

Health and Safety (First aid) Regulations 1981

17.16.19

References

Regulatory Reform, England and Wales. The Regulatory Reform (Fire Safety) Order 2005 SI 2005 No 1541 There are a total of eleven guides produced the Department of Communities and Local Government publications covering the following subjects: Ofﬁces and Shops Premises providing Sleeping Accommodation ISBN 13978 1 85112 817 4 Residential Care ISBN 13978 1 85112 818 1 Small and Medium Places of Assembly ISBN 13978 1 85112 820 4 Large Places of Assembly ISBN 13978 1 85112 821 1 Factories and Warehouses ISBN 13978 1 85112 816 7 Theatres and Cinemas ISBN 13978 1 85112 822 8 Educational Premises ISBN 13978 1 85112 819 8 Healthcare Premises ISBN 13978 1 85112 824 2 Transport Premises and Facilities ISBN 13978 1 85112 825 9 Open Air Events ISBN 13978 1 85112 823 5

17.17

Duty of the employer – Regulation 3

An employer shall provide, or ensure that there are provided: ➤ adequate and appropriate facilities and equipment ➤ qualiﬁed ﬁrst aiders to render ﬁrst aid ➤ an appointed person, being someone to take charge of situations as well as ﬁrst aid equipment and facilities, where medical aid needs to be summoned. An appointed person will sufﬁce where: ➤ the nature of the work is such that there are no speciﬁc serious hazards (ofﬁces, libraries etc), the workforce is small, the location makes further provision unnecessary ➤ there is temporary (not planned holidays) or exceptional absence of the ﬁrst aider. There must always be at least an appointed person in every workplace during working hours. Employers must make an assessment of the ﬁrst aid requirements that are appropriate for each workplace.

17.17.2

Employees information – Regulation 4

Employees must be informed of the arrangements for ﬁrst aid, including the location of facilities, equipment and people.

17.17.3

Self-employed – Regulation 5

The self-employed shall provide such ﬁrst aid equipment as is appropriate to render ﬁrst aid to themselves.

17.17.4

References

HSE, L74 First aid at work. Health and Safety (First Aid) regulations 1981. Approved code of practice and guidance, HSE Books ISBN 0-7176-1050-0

Health and Safety (First aid) Regulations 1981

17.18

Health and Safety (Information for Employees) Regulations 1989

These Regulations set out employers’ duties to provide adequate ﬁrst aid facilities. They deﬁne ﬁrst aid as:

17.18.1

General requirements

➤ treatment for the purposes of preserving life and minimizing the consequences of injury and illness until medical help is obtained

These regulations require that the Approved Poster entitled, Health and safety – what you should know, is displayed or the Approved Leaﬂet is distributed.

358

Summary of the main legal requirements This information tells employees in general terms about the requirements of health and safety law. Employers must also inform employees of the local address of the enforcing authority (either the HSE or the local authority) and the Employment Medical Advisory Service. This should be marked on the poster or supplied with the leaﬂet. Since 1 July 2000 the latest version of the poster must be displayed or distributed. References to obsolete legal requirements are removed and the revised text focuses on the modern framework of general duties, supplemented by the basics of health and safety management and risk assessment. It includes two additional boxes: one for details of trade union or other safety representatives and one for competent persons appointed to assist with health and safety and their responsibilities.

References

17.19

Hazardous Waste (England and Wales) Regulations 2005

17.19.1

Introduction

The Hazardous Waste (England and Wales) Regulations 2005 were implemented on 16th July 2005. These are made under the Environmental Protection Act 1990. There were many changes to the previous Special Waste Regulations, but the two key ones are that Hazardous waste producers are now required to pre-register before any Hazardous waste can be collected from their premises and the Regulations apply the European Waste Catalogue codes of Hazardous wastes that will affect a much wider range of producers.

17.19.2

Summary

The list below is not exhaustive, but summarizes the main requirements. There is also a range of web links that will help to obtain more detail. ➤ From 16 July 2005, it is an offence for hazardous waste to be collected from a site that has not been registered or is exempt.

359

Hazardous Waste (England and Wales) Regulations 2005

Health and Safety (Information for Employees) Regulations 1989 (SI No 682) Health and Safety Information for Employees (Modiﬁcations and Repeals) Regulations 1995 Poster ISBN 0-7176-2493-5 Leaﬂet ISBN 0-7176-1702-5

17.19

17.18.2

➤ All non-exempt sites that produce hazardous waste must be registered even if they are unlikely to have that waste collected for some time. Recent EA Guidance has clariﬁed that it is an offence to produce hazardous waste on site and not be registered. ➤ The Regulations implement, through the List of Wastes (England) Regulations 2005, the European Waste Catalogue list of Hazardous wastes for the purposes of collection. This can be found at www.hmso. gov.uk and will mean that things like PC monitors, PC base units, fridges, TVs, oily rags and separately collected ﬂuorescent tubes require collection under the new hazardous waste notiﬁcation and documentation procedures. ➤ The EA will accept postal registrations and registrations can be made on line through the following website www.environment-agency.gov.uk. ➤ Each site producing hazardous waste has to have a separate registration although multiple sites can be registered on the same notiﬁcation. Therefore, a head ofﬁce could register all its sites centrally, but each site would have a separate unique registration number and require a separate fee. ➤ Some sites are exempt if they expect to produce less than 200 kgs of hazardous waste a year – although they would then have to register if, part way through the year, they went over the threshold. These include agricultural premises, ofﬁce premises, shops, premises where WEEE is collected, dental, veterinary and medical practices and ships. The EA indicate that 200 kgs is approximately 10 small TVs, 500 ﬂuorescent tubes or 5 small domestic fridges. ➤ Domestic waste is excluded from the Hazardous Waste Regulations on collection from the domestic property, but is then subject to the Regulations if it is separately collected or if it consists of asbestos. This includes Prescription Only Medicines (other than cytotoxic and cytostatic medicines) which will be hazardous waste. ➤ The Regulations require a new consignment note to be used from 16 July 2005 in place of the former Section 62. Each consignment will require a fee to be paid to the EA by the consignee with their quarterly returns to the Agency. Clearly, this will be charged back to the collector, but a consignment might well attract more than one consignment fee if, for instance, it goes through a transfer station and the collector would have to ensure that this was considered in the price. ➤ Collection rounds will be possible but again, each site where the waste is collected would have to be left a copy of the consignment note, so the process of tracking and the paper trail will get quite complex especially as each collection will count as a consignment from the fee point of view.

Introduction to Health and Safety at Work ➤ The Regulations ban the mixing of Hazardous waste and state that it must be stored separately on site. However, clariﬁcation on the interpretation of this is still awaited from the EA as it would, for instance, preclude the collection of computer systems that included a base unit and screen. ➤ Registration as a Hazardous Waste producer places a statutory duty on the EA to inspect the site where the hazardous waste arises.

17.20 Ionising Radiation Regulations 1999

17.19.3

References

A guide to the Hazardous Waste Regulations and the List of Waste Regulations in England and Wales, Environment Agency, HWR01. See www.environment-agency. gov.uk

17.20

17.20.1

Ionising Radiation Regulations 1999 Introduction

The Ionising Radiations Regulations 1999 (IRR99) implement the majority of the Basic Safety Standards Directive 96129/Euratom (BSS Directive). From 1 January 2000, they replaced the Ionising Radiations Regulations 1985 (IRR85) (except for Regulation 26 (special hazard assessments)). The main aim of the Regulations and the supporting ACOP is to establish a framework for ensuring that exposure to ionizing radiation arising from work activities, whether from man-made or natural radiation and from external radiation (e.g. X-ray set) or internal radiation (e.g. inhalation of a radioactive substance), is kept as low as reasonably practicable and does not exceed dose limits speciﬁed for individuals. IRR99 also: (a) replace the Ionising Radiations (Outside Workers) Regulations 1993 (OWR93), which were made to implement the Outside Workers Directive 90/641/ Euratom, and (b) implement a part of the Medical Exposures Directive 97143/Euratom in relation to equipment used in connection with medical exposures. The guidance which accompanies the Regulations and ACOP gives detailed advice about the scope and duties of the requirements imposed by IRR99. It is aimed at employers with duties under the Regulations but should also be useful to others such as radiation protection

360

advisers, health and safety ofﬁcers, radiation protection supervisors and safety representatives.

17.20.2

Working with ionising radiation

Essentially, work with ionising radiation means: (a) a practice, which involves the production, processing, handling, use, holding, storage, transport or disposal of artiﬁcial radioactive substances and some naturally occurring sources, or the use of electrical equipment emitting ionizing radiation at more than 5 kV (see deﬁnition of practice in Regulation 2 (1)) (b) work in places where the radon gas concentration exceeds the values in Regulation 3 (1) (b), or (c) work with radioactive substances containing naturally occurring radionuclides not covered by the deﬁnition of a practice.

17.20.3

Radiation employers

Radiation employers are essentially those employers who work with ionising radiation, i.e. they carry out: (a) a practice (see deﬁnition in Regulation 2 (1)), or (b) work in places where the radon gas concentration exceeds the values in Regulation 3 (1) (b), or (c) work with radioactive substances containing naturally occurring radionuclides not covered by the deﬁnition of a practice.

17.20.4

Duties of self-employed people

A self-employed person who works with ionising radiation will simultaneously have certain duties under these Regulations, both as an employer and as an employee. For example, self-employed persons may need to take such steps as: ➤ carrying out assessments under Regulation 7 ➤ providing control measures under Regulation 8 to restrict exposure ➤ designating themselves as classiﬁed persons under Regulation 20 ➤ making suitable arrangements under Regulation 21 with one or more approved dosimetry services (ADS) for assessment and recording of doses they receive ➤ obtaining a radiation passbook and keeping it up to date in accordance with Regulation 2 ➤ if they carry out services as an outside worker, making arrangements for their own training as required by Regulation 14 ➤ ensuring they use properly any dose meters provided by an ADS as required by regulation.

Summary of the main legal requirements 17.20.5

General requirements

This prior risk assessment should enable the employer to determine:

Some of the major considerations are:

➤ notiﬁcation to HSE of speciﬁc work unless speciﬁed in schedule 1 to the regulations (Regulation 6) ➤ carrying out prior risk assessment by a radiation employer before commencing a new activity (Regulation 7) ➤ use of personal protective equipment (Regulation 9) ➤ maintenance and examination of engineering controls and PPE (Regulation 10) ➤ dose limitations (Regulation 11) ➤ contingency plans for emergencies (Regulation 12) ➤ radiation protection adviser appointment (Regulation 13) ➤ information instruction and training (Regulation 14).

17.20.6

Prior risk assessment

Where a radiation employer is required to undertake a prior risk assessment, the following matters need to be considered, where they are relevant:

➤ the nature of the sources of ionizing radiation to be used, or likely to be present, including accumulation of radon in the working environment ➤ estimated radiation dose rates to which anyone can be exposed ➤ the likelihood of contamination arising and being spread ➤ the results of any previous personal dosimetry or area monitoring relevant to the proposed work ➤ advice from the manufacturer or supplier of equipment about its safe use and maintenance ➤ engineering control measures and design features already in place or planned ➤ any planned systems of work; estimated levels of airborne and surface contamination likely to be encountered ➤ the effectiveness and the suitability of personal protective equipment to be provided ➤ the extent of unrestricted access to working areas where dose rates or contamination levels are likely to be signiﬁcant; possible accident situations, their likelihood and potential severity ➤ the consequences of possible failures of control measures – such as electrical interlocks, ventilation systems and warning devices – or systems of work; steps to prevent identiﬁed accident situations, or limit their consequences.

➤ what action is needed to ensure that the radiation exposure of all persons is kept as low as reasonably practicable (Regulation 8 (1)) ➤ what steps are necessary to achieve this control of exposure by the use of engineering controls, design features, safety devices and warning devices (Regulation 8 (2) (a)) and, in addition, by the development of systems of work (Regulation 8 (2) (b)) ➤ whether it is appropriate to provide personal protective equipment and if so what type would be adequate and suitable (Regulation 8 (2) (c)) ➤ whether it is appropriate to establish any dose constraints for planning or design purposes, and if so what values should be used (Regulation 8 (3)) ➤ the need to alter the working conditions of any female employee who declares she is pregnant or is breastfeeding (Regulation 8 (5)) ➤ an appropriate investigation level to check that exposures are being restricted as far as reasonably practicable (Regulation 8 (7)) ➤ what maintenance and testing schedules are required for the control measures selected (Regulation 10) ➤ what contingency plans are necessary to address reasonably foreseeable accidents (Regulation 12) ➤ the training needs of classiﬁed and non-classiﬁed employees (Regulation 14) ➤ the need to designate speciﬁc areas as controlled or supervised areas and to specify local rules (Regulations 16 and 17) ➤ the actions needed to ensure restriction of access and other speciﬁc measures in controlled or supervised areas (Regulation 18) ➤ the need to designate certain employees as classiﬁed persons (Regulation 20) ➤ the content of a suitable programme of dose assessment for employees designated as classiﬁed persons and for others who enter controlled areas (Regulations 18 and 21) ➤ the responsibilities of managers for ensuring compliance with these Regulations ➤ an appropriate programme of monitoring or auditing of arrangements to check that the requirements of these Regulations are being met.

17.20.7

References

HSC, L121, 2000 HSE Books, ISBN 0-7176-1746-7. This is a large document and need only be studied by those with a speciﬁc need to control IR. The HSE have also produced a number of information sheets which are available free on the Internet at their web site.

361

Introduction to Health and Safety at Work

17.21

Lifting Operations and Lifting Equipment Regulations 1998 as amended in 2002

Control of radioactive substances IRIS8 2001 HSE Books

17.21

Lifting Operations and Lifting Equipment Regulations 1998 as amended in 2002

17.21.1

Introduction

This summary gives information about the Lifting Operations and Lifting Equipment Regulations 1998 (LOLER) which came into force on 5 December 1998. In the main, LOLER replaced existing legal requirements relating to the use of lifting equipment, for example the Construction (Lifting Operations) Regulations 1961, the Docks Regulations 1988 and the Lifting Plant and Equipment (Records of Test and Examination etc.) Regulations 1992. The Regulations aim to reduce risks to people’s health and safety from lifting equipment provided for use at work. In addition to the requirements of LOLER, lifting equipment is also subject to the requirements of the Provision and Use of Work Equipment Regulations 1998 (PUWER). Generally, the Regulations require that lifting equipment provided for use at work is: ➤ strong and stable enough for the particular use and marked to indicate safe working loads ➤ positioned and installed to minimize any risks ➤ used safely, i.e. the work is planned, organized and performed by competent people ➤ subject to ongoing thorough examination and, where appropriate, inspection by competent people.

17.21.2

Definition

Lifting equipment includes any equipment used at work for lifting or lowering loads, including attachments used for anchoring, ﬁxing or supporting it. The Regulations cover a wide range of equipment including, cranes, fork lift trucks, lifts, hoists, mobile elevating work platforms, and vehicle inspection platform hoists. The deﬁnition also includes lifting accessories such as chains, slings, eyebolts etc. LOLER does not apply to escalators, these are covered by more speciﬁc legislation, i.e. the Workplace (Health, Safety and Welfare) Regulations 1992. If employees are allowed to provide their own lifting equipment, then this too is covered by the Regulations.

17.21.3

Application

The Regulations apply to an employer or self-employed person providing lifting equipment for use at work, or

362

who has control of the use of lifting equipment. They do not apply to equipment to be used primarily by members of the public, for example, lifts in a shopping centre. However, such circumstances are covered by the HSW Act 1974. LOLER applies to the way lifting equipment is used in industry and commerce. LOLER applies only to work activities, for example: ➤ a crane on hire to a construction site ➤ a contract lift ➤ a passenger lift provided for use of workers in an ofﬁce block ➤ refuse collecting vehicles lifting on a public road ➤ patient hoist ➤ fork lift truck. These Regulations add to the requirements of PUWER 98 and should be interpreted with them. For example, when selecting lifting equipment, PUWER Regulation 4, regarding suitability, should be considered in connection with: ➤ ➤ ➤ ➤ ➤

ergonomics the conditions in which the equipment is to be used safe access and egress preventing slips trips and falls protecting the operator.

While employees do not have duties under LOLER, they do have general duties under the HSW Act and the Management of Health and Safety at Work Regulations 1992 (MHSWR), for example, to take reasonable care of themselves and others who may be affected by their actions and to co-operate with others. The Regulations cover places where the HSW Act applies – these include factories, offshore installations, agricultural premises, ofﬁces, shops, hospitals, hotels, places of entertainment etc.

17.21.4

Strength and stability – Regulation 4

Lifting equipment shall be of adequate strength and stability for each load, having regard in particular to the stress induced at its mounting or ﬁxing point. Every part of a load and anything attached to it and used in lifting it shall be of adequate strength. Account must be taken of the combination of forces to which the lifting equipment will be subjected, as well as the weight of any lifting accessories. The equipment should include an appropriate factor of safety against failure. Stability needs to take into account the nature, loadbearing strength, stability, adjacent excavations and

Summary of the main legal requirements slope of the surface. For mobile equipment, keeping rails free of obstruction and tyres correctly inﬂated must be considered.

17.21.7

Marking of lifting equipment – Regulation 7

Machinery and accessories for lifting loads shall be clearly marked to indicate their safe working loads (SWL), and:

17.21.5 Lifting equipment for lifting persons – Regulation 5 To ensure safety of people being lifted, there are additional requirements for such equipment. The use of equipment not speciﬁcally designed for raising and lowering people should only be used in exceptional circumstances. The regulation applies to all lifting equipment used for raising and lowering people and requires that lifting equipment for lifting persons shall: ➤ prevent a person using it from being crushed, trapped or struck, or falling from the carrier ➤ prevent, so far as is reasonably practicable, persons using it while carrying out work, from the carrier being crushed, trapped or struck or falling from the carrier ➤ have suitable devices to prevent the risk of the carrier falling. If a device cannot be ﬁtted, the carrier must have: ➤ an enhanced safety coefﬁcient suspension rope or chain ➤ the rope or chain inspected every working day by a competent person ➤ be such that a person trapped in any carrier is not thereby exposed to any danger and can be freed.

17.21.6 Positioning and installation – Regulation 6 Lifting equipment must be positioned and installed so as to reduce the risks, so far as is reasonably practicable, from: ➤ equipment or a load striking another person ➤ a load drifting, falling freely or being released unintentionally and it is otherwise safe. Lifting equipment should be positioned and installed to minimize the need to lift loads over people and to prevent crushing in extreme positions. It should be designed to stop safely in the event of a power failure and not release its load. Lifting equipment, which follows a ﬁxed path, should be enclosed with suitable and substantial interlocked gates and any necessary protection in the event of power failure.

➤ where the SWL depends on the conﬁguration of the lifting equipment: ➤ the machinery should be clearly marked to indicate its SWL for each conﬁguration ➤ information which clearly indicates its SWL for each conﬁguration should be kept with the machinery ➤ accessories for lifting (e.g. hooks, slings) are also marked in such a way that it is possible to identify the characteristics necessary for their safe use (e.g. if they are part of an assembly) ➤ lifting equipment which is designed for lifting people is appropriately and clearly marked ➤ lifting equipment not designed for lifting people, but which might be used in error, should be clearly marked to show it is not for lifting people.

17.21.8

Organization of lifting operations – Regulation 8

Every lifting operation, that is lifting or lowering of a load, shall be: ➤ properly planned by a competent person ➤ appropriately supervised ➤ carried out in a safe manner. The person planning the operation should have adequate practical and theoretical knowledge and experience of planning lifting operations. The plan will need to address the risks identiﬁed by the risk assessment and identify the resources, the procedures and the responsibilities required so that any lifting operation is carried out safely. For routine simple lifts a plan will normally be left to the people using the lifting equipment. For complex lifting operations, for example, where two cranes are used to lift one load, a written plan may need to be produced each time. The planning should take account of, avoiding suspending loads over occupied areas, visibility, attaching/detaching and securing loads, the environment, location, overturning, proximity to other objects, lifting of people and pre-use checks of the equipment.

17.21.9

Thorough examination and inspection – Regulation 9

Before using lifting equipment for the ﬁrst time by an employer, it must be thoroughly examined for any defect unless either: ➤ the lifting equipment has not been used before ➤ an EC declaration of conformity (where one should have been drawn up) has been received or made not

363

Introduction to Health and Safety at Work more than 12 months before the lifting equipment is put into service ➤ if it is obtained from another undertaking, it is accompanied by physical evidence of an examination. A copy of this thorough examination report shall be kept for as long as the lifting equipment is used (or, for a lifting accessory, two years after the report is made) (Regulation 11). Where safety depends on the installation conditions, it shall be thoroughly examined: ➤ after installation and before being put into service ➤ after assembly and before being put into service at a new site or in new location to ensure that it has been installed correctly and is safe to operate. A copy of the thorough examination report shall be kept for as long as the lifting equipment is used at the place it was installed or assembled (Regulation 11). Lifting equipment, which is exposed to conditions causing deterioration, which may result in dangerous situations, shall be: ➤ thoroughly examined at least every 6 months (for lifting equipment for lifting persons, or a lifting accessory); at least every 12 months (for other lifting equipment); or in accordance with an examination scheme; and each time that exceptional circumstances, liable to jeopardize the safety of the lifting equipment, have occurred and a copy of the report kept until the next report is made, or for two years (whichever is longer) ➤ inspected, if appropriate, by a competent person at suitable intervals between ‘thorough examinations’ (and a copy of the record kept until the next record is made). All lifting equipment shall be accompanied by physical evidence that the last ‘thorough examination’ has been carried out before it leaves an employer’s undertaking (or before it is used after leaving another undertaking). The user, owner, manufacturer or some other independent party may draw up examination schemes provided they have the necessary competence. Schemes should specify the intervals at which lifting equipment should be thoroughly examined and, where appropriate, those parts that need to be tested. The scheme should take account, for example, of its condition, the environment in which it is used, the number of lifting operations and the loads lifted. The ‘competent person’ carrying out a thorough examination should have appropriate practical and theoretical knowledge and experience of the lifting

364

equipment to be examined to enable them to detect defects or weaknesses and to assess their importance in relation to the safety and continued use of the lifting equipment. They should also determine whether a test is necessary and the most appropriate method for carrying it out.

17.21.10

Reports and defects – Regulation 10

The person making a ‘thorough examination’ of lifting equipment shall: ➤ notify the employer forthwith of any defect which, in their opinion, is or could become, dangerous ➤ as soon as is practicable (within 28 days) write an authenticated report to: ➤ the employer ➤ any person who hired or leased the lifting equipment, containing the information speciﬁed in Schedule 1 ➤ send a copy (as soon as is practicable) to the relevant enforcing authority where there is, in their opinion, a defect with an existing or imminent risk of serious personal injury (this will always be HSE if the lifting equipment has been hired or leased). Every employer notiﬁed of a defect following a ‘thorough examination’ of lifting equipment should ensure that it is not used: ➤ before the defect is rectiﬁed ➤ after a time speciﬁed in the schedule accompanying the report. The person making an ‘inspection’ shall also notify the employer when, in his or her opinion, a defect is, or could become, dangerous and, as soon as is practicable, make a record of the inspection in writing.

17.21.11

Reports – Schedule 1

Schedule 1 lists the information to be contained in a report of a thorough examination. For example, name and address; identity of equipment; date of last through examination; SWL; appropriate interval; any dangerous or potentially dangerous defects; repairs required; date of next examination and test; details of the competent person.

17.21.12

References

Safe use of lifting equipment, Lifting Operations and Lifting Equipment Regulations 1998 Approved Code of Practice and Guidance, L113, 1998 HSE Books ISBN 0-7176-1628-2

Summary of the main legal requirements

Management of Health and Safety at Work Regulations 1999 as amended in 2003

17.22.1

General

These Regulations give effect to the European Framework Directive on health and safety. They supplement the requirements of the Health and Safety at Work Act etc. 1974 and specify a range of management issues, most of which must be carried out in all workplaces. The aim is to map out the organization of precautionary measures in a systematic way, and to make sure that all staff are familiar with the measures and their own responsibilities. They were amended slightly in 2003 particularly in relation to civil liability (Regulation 22)

17.22.2

Risk assessment – Regulation 3

Every employer is required to make a ‘suitable and sufﬁcient’ assessment of risks to employees, and risks to other people who might be affected by the organization, such as visiting contractors and members of the public. A systematic investigation of risks involved in all areas and operations is required, together with identiﬁcation of the persons affected, a description of the controls in place and any further action required to reduce risks. The risk assessments must take into account risks to new and expectant mothers and young people. Signiﬁcant ﬁndings from the assessments must be written down (or recorded by other means, such as on a computer) when there are ﬁve or more employees. The assessments need to be reviewed regularly and if necessary, when there have been signiﬁcant changes, they should be modiﬁed.

17.22.3

17.22.4

Effective arrangements for health and safety – Regulation 5

Formal arrangements must be devised (and recorded) for effective planning, organization, control, monitoring and review of safety measures. This will involve an effective health and safety management system to implement the policy. Where there are ﬁve or more employees the arrangements should be recorded. Planning involves a systematic approach to risk assessment, the selection of appropriate risk controls and establishing priorities with performance standards. Organization involves consultation and communication with employees; employee involvement in risk assessment; the provision of information and securing competence with suitable instruction and training. Control involves clarifying responsibilities and making sure people adequately fulﬁl their responsibilities. It involves adequate and appropriate supervision. Monitoring should include the measurement of how well the policy is being implemented and whether hazards are being controlled properly. It covers inspections of the workplace and management systems: the investigation of incidents and accidents to ascertain the underlying causes and affect a remedy. Review is essential to look at the whole of the health and safety management system to ensure that it is effective and achieving the correct standard of risk control.

Principles of prevention – Regulation 4 17.22.5

The following principles must be adopted when implementing any preventative and protective measures: ➤ avoiding risks ➤ evaluating the risks which cannot be avoided ➤ combating the risks at source

Health surveillance – Regulation 6

In appropriate circumstances health surveillance of staff may be required – the Approved Code of Practice describes more fully when this duty will arise. Health surveillance is considered relevant when there is an identiﬁable disease or poor health condition; there are techniques

365

Management of Health and Safety at Work Regulations 1999 as amended in 2003

17.22

➤ adapting the work to the individual, especially as regards the design of workplaces, the choice of work equipment and the choice of working and production methods, with a view, in particular, to alleviating monotonous work and work at a predetermined work-rate and to reducing their effect on health ➤ adapting to technical progress ➤ replacing the dangerous by the non-dangerous or the less dangerous ➤ developing a coherent overall prevention policy which covers technology, organization of work, working conditions, social relationships and the inﬂuence of factors relating to the working environment ➤ giving collective protective measures priority over individual protective measures ➤ giving appropriate instruction to employees.

17.22

Simple guide to the LOLER, 1999 HSE, INDG290, HSE Books ISBN 0-7176-2430-7 LOLER 1998 Lifting Operations and Lifting Equipment Regulations 1998, Open learning guidance. 1999 HSE Books ISBN 0-7176-2464-1

Introduction to Health and Safety at Work to detect the disease; there is a reasonable likelihood that the disease will occur; and surveillance is likely to enhance the protection of the workers concerned. A competent person, who will range from a manager, in some cases, to a fully qualiﬁed occupational medical practitioner in others, should assess the extent of the surveillance.

17.22.6

Competent assistance – Regulation 7

Every employer is obliged to appoint one or more ‘competent person(s)’ to advise and assist in undertaking the necessary measures to comply with the relevant statutory requirements. They may be employees or outside consultants. The purpose is to make sure that all employers have access to health and safety expertise. Preference should be given to an in-house appointee who may be backed up by external expertise. The competence of the person (s) appointed is to be judged in terms of their training, knowledge and experience of the work involved; it is not necessarily dependent upon particular qualiﬁcations. In simple situations, it may involve knowledge of relevant best practice, knowing one’s limitations and taking external advice when necessary. In more complex situations or risks, fully qualiﬁed and appropriately experienced practitioners will be required. Appointed competent persons must be provided with adequate information, time and resources to do their job.

17.22.7 Procedures for serious and imminent danger and contact with external services – Regulations 8 and 9 Procedures must be established for dealing with serious and imminent dangers, including ﬁre evacuation plans and arrangements for other emergencies. A sufﬁcient number of competent persons must be appointed to evacuate the premises in the event of an emergency. The procedures should allow for persons at risk to be informed of the hazards and how and when to evacuate to avoid danger. In shared workplaces employers must co-operate. Access to dangerous areas should be restricted to authorized and properly trained staff. Any necessary contact arrangements with external services for ﬁrst aid, emergency medical care and rescue work must be set up.

17.22.8 Information for employees – Regulation 10 Information must be provided to staff on the risk assessment, risk controls, emergency procedures, the identity of the people appointed to assist on health and safety matters and risks notiﬁed by others.

366

The information provided must take into account the level of training, knowledge and experience of the employees. It must take account of language difﬁculties and be provided in a form that can be understood by everyone. The use of translations, symbols and diagrams should be considered. Where children under school leaving age are at work, information on the risk assessments and control measures must be provided to the child’s parent or guardians of children at work before the child starts work. It can be provided verbally or directly to the parent, guardians or school.

17.22.9

Co-operation and coordination – Regulations 11, 12 and 15

Where two or more employers share a workplace, each must: ➤ co-operate with other employers in health and safety matters ➤ take reasonable steps to coordinate their safety precautions ➤ inform the other employers of the risks to their employees, i.e. risks to neighbours’ employees. ➤ where people from outside organizations are present to do work they, and their employers, have to be provided with appropriate information on risks, health and the necessary precautions to be taken ➤ Temporary staff and staff with ﬁxed-term contracts as well as permanent employees must be supplied with health and safety information before starting work (Regulations 12 and 15) ➤ Regulation 11 does not apply to multi-occupied premises or sites where each unit, under the control of an individual tenant employer or self-employed person, is regarded as a separate workplace. In other cases, common areas may be shared workplaces, such as a reception area or canteen or they may be under the control of a person to whom Section 4 of HSW Act applies. Suitable arrangements may need to be put in place for these areas.

17.22.10

Capabilities and training – Regulation 13

When giving tasks to employees, their capabilities with regard to health and safety must be taken into account. Employees must be provided with adequate health and safety training: ➤ on recruitment ➤ on being exposed to new or increased risks ➤ on the introduction of new procedures, systems or technology. Training must be repeated periodically and take place in working hours (or while being paid).

Summary of the main legal requirements 17.22.11

Duties on employees – Regulation 14

Equipment and materials must be used properly in accordance with instructions and training. Obligations on employees are extended to include certain requirements to report serious and immediate dangers and any shortcomings in the employer’s protection arrangements.

➤ what types of work equipment will be used and how this will be handled ➤ how the work and processes involved are organized ➤ the need to assess and provide health and safety training, and ➤ risks from the particular agents, processes and work.

17.22.14 17.22.12 New or expectant mothers – Regulations 16, 17 and 18

Young persons – Regulation 19

Employers must protect young persons at work from risks to their health and safety which are the result of lack of experience, or absence of awareness of existing or potential risks or because they have not yet fully matured. Young persons may not be employed in a variety of situations, which pose a signiﬁcant risk to their health and safety which are a consequence of the following factors: ➤ ➤ ➤ ➤ ➤ ➤ ➤

physical or psychological capacity pace of work temperature extremes, noise or vibration radiation compressed air and diving hazardous substances lack of training and experience.

The exception to this is young persons over school leaving age: ➤ where the work is necessary for their training ➤ where they will be supervised by a competent person ➤ where the risk will be reduced to the lowest level that is reasonably practicable.

17.22.15

Restriction of Civil Liability for Breach of Statutory Duty Regulation 22

By the 2003 Amendment Regulations (SI 2003 No 2457) Regulation 22 was changed from an exclusion of civil liability to the following; Breach of a duty imposed on an employer by these Regulations shall not confer a right of action in any civil proceedings insofar as that duty applies for the protection of persons not in their employment.

17.22.16

References

The Management of Health and Safety at Work Regulations 1999 HMSO ISBN 0-11-025051-6 Management of Health and Safety at Work and Fire Precautions (Workplace) (Amendment) Regulations 2003 Stationery Ofﬁce Si 2003 No 2457 Management of health and safety at work:Approved Code of Practice and Guidance, HSC L21, Second Edition 2000 HSE Books ISBN 0-7176-2488-9 Five Steps to Risk Assessment, HSE INDG163 (rev1). 1999 HSE Books

17.23

Manual Handling Operations Regulations (MHO) 1992 as amended in 2002

The risk assessment must take the following speciﬁc factors into account:

17.23.1

General

➤ the ﬁtting-out and layout of the workplace and the particular site where they will work ➤ the nature of any physical, biological and chemical agents they will be exposed to, for how long and to what extent

The Regulations apply to the manual handling (any transporting or supporting) of loads, i.e. by human effort, as opposed to mechanical handling by fork lift truck, crane, etc. Manual handling includes lifting, putting down, pushing, pulling, carrying or moving. The human effort may be

367

Manual Handling Operations Regulations (MHO) 1992 as amended in 2002

17.22.13

This provision is to prevent a defense for an employer by reason of any act or default by an employee or a competent person appointed under Regulation 7. Employees duties to take reasonable care of their own health and safety and that of others affected by their work activities is unaffected by this provision.

17.23

Where work is of a kind that could present a risk to new or expectant mothers working there or their babies, the risk assessments must include an assessment of such risks. When the risks cannot be avoided the employer must alter a women’s working conditions or hours to avoid the risks; offer suitable alternative work; or suspend from work on full pay. The woman must notify the employer in writing of her pregnancy, that she has given birth within the last six months or she is breastfeeding.

Provisions as to liability – Regulation 21

Introduction to Health and Safety at Work applied directly to the load, or indirectly by pulling on a rope, chain or lever. Introducing mechanical assistance, like a hoist or sack truck, may reduce but not eliminate manual handling, since human effort is still required to move, steady or position the load. The application of human effort for purposes other than transporting or supporting a load; for example, pulling on a rope to lash down a load or moving a machine control, is not a manual handling operation. A load is a discrete movable object, but it does not include an implement, tool or machine while being used. Injury in the context of these Regulations means to any part of the body. It should take account of the physical features of the load which might affect grip or cause direct injury, for example, slipperiness, sharp edges, and extremes of temperature. It does not include injury caused by any toxic or corrosive substance which has leaked from a load, is on its surface or is part of the load.

17.23.2 Duties of employers – avoidance of manual handling – Regulation 4 (1) (a) Employers should take steps to avoid the need for employees to carry out MHO which involves a risk of their being injured. The guidance suggests that a preliminary assessment should be carried out when making a general risk assessment under the Management of Health and Safety at Work Regulations 1999. Employers should consider whether the operation can be eliminated, automated or mechanized.

17.23.3 Duties of employers assessment of risk – Regulation 4 (1) (b) (i) Where it is not reasonably practicable to avoid MHO, employers must make a suitable and sufﬁcient risk assessment of all such MHO in accordance with the requirements of Schedule 1 to the Regulations (shown later). This duty to assess the risk takes into account the task, the load, the working environment and individual capability.

17.23.4 Duties of employers – reducing the risk of injury – Regulation 4 (1) (b) (ii) Where it is not reasonably practicable to avoid the MHO at which there is a risk of injury, employers must take steps to reduce the risk of injury to the lowest level reasonably practicable. The structured approach (considering the task, the load, the working environment and the individual capability) is recommended in the guidance. The steps taken

368

will involve ergonomics, changing the load, mechanical assistance, task layout, work routines, personal protective equipment, team working and training.

17.23.5

Duties of employers – additional information on the load – Regulation 4 (1) (b) (iii)

Employers must take appropriate steps where manual handling cannot be avoided to provide general indications and, where practicable precise information on: ➤ the weight of each load ➤ the heaviest side of any load which does not have a central centre of gravity. The information is probably best marked on the load. Sections 3 and 6 of the HSW Act may place duties on originators of loads, like manufacturers or packers.

17.23.6

Duties of employers – reviewing assessment – Regulation 4 (2)

The assessment should be reviewed if there is reason to suspect that it is no longer valid or there have been signiﬁcant changes in the particular MHO.

17.23.7

Individual Capability Regulation 4 (3) (a)–(f)

A new requirement was added in 2002 by Amendment Regulations concerning the individual capabilities of people undertaking manual handling. Regard must be had in particular to: (a) the physical suitability of the employee to carry out the operation (b) the clothing, footwear or other personal effects they are wearing (c) their knowledge and training (d) results of any relevant risk assessments carried out under Regulation 3 of the Management Regulations 1999 (e) whether the employee is within a group of employees identiﬁed by that assessment as being especially at risk, and (f) the results of any health surveillance provided pursuant to Regulation 6 of the Management Regulations 1999.

17.23.8

Duty of employees – Regulation 5

Each employee, while at work, has to make proper use of any system of work provided for their use. This

Summary of the main legal requirements Table 17.6 Schedule 1 to the Manual Handling Operations Regulations Factors to which the employer must have regard and questions they must consider when making an assessment of manual handling operations

1 The tasks

Do they involve: Holding or manipulating loads at distance from trunk? Unsatisfactory bodily movement or posture, especially: Twisting the trunk? Stooping? Reaching upwards? Excessive movement of loads especially: Excessive lifting or lowering distances? Excessive carrying distances? Excessive pulling or pushing of loads? Risk of sudden movement of loads? Frequent or prolonged physical effort? Insufﬁcient rest or recovery periods? A rate of work imposed by a process?

2 The loads

Are they: Heavy? Bulky or unwieldy? Difﬁcult to grasp? Unstable, or with contents likely to shift? Sharp, hot or otherwise potentially damaging?

3 The working environment

Are there: Space constraints preventing good posture? Uneven, slippery or unstable ﬂoors? Variations in level of ﬂoors or work surfaces? Extremes of temperature or humidity? Conditions causing ventilation problems or gusts of wind? Poor lighting conditions?

4 Individual capability

Does the job: Require unusual strength, height, etc.? Create a hazard to those who might reasonably be considered to be pregnant or have a health problem? Require special information or training for its safe performance?

5 Other factors

Is movement or posture hindered by personal protective equipment or by clothing?

is in addition to other responsibilities under the HSW Act and the Management of Health and Safety at Work Regulations. The provisions do not include well-intentioned improvization in an emergency, for example, rescuing a casualty or ﬁghting a ﬁre.

Manual Handling, Manual Handling Operations Regulations 1992 (as amended), Guidance on Regulations third edition, L23, 2004 HSE Books ISBN 0-7176-2823–x Manual Handling, Solutions you can handle, HSG 115, 1994 HSE Books ISBN 0-7176-0693-7 Getting to Grips with manual handling. A short guide for employers revised. INDG 143 ISBN 0-7176-1754-8

17.24 Control of Noise at Work Regulations 2005 17.24.1

Introduction

The Control of Noise at Work Regulations 2005 require employers to prevent or reduce risks to health and safety from exposure to noise at work. Employees also have duties under the Regulations. The Regulations require employers to: ➤ assess the risks to their employees from noise at work; ➤ take action to reduce the noise exposure that produces those risks ➤ provide their employees with hearing protection if they cannot reduce the noise exposure enough by using other methods ➤ make sure the legal limits on noise exposure are not exceeded ➤ provide their employees with information, instruction and training ➤ carry out health surveillance where there is a risk to health. The Regulations do not apply to: ➤ members of the public exposed to noise from their non-work activities, or making an informed choice to go to noisy places ➤ low-level noise which is a nuisance but causes no risk of hearing damage. Employers in the music and entertainment sectors have until 6 April 2008 to comply with the Noise Regulations 2005. Meanwhile they must continue to comply with the Noise at Work Regulations 1989, which the 2005 Regulations replace for all other workplaces.

369

Control of Noise at Work Regulations 2005

Questions

References

17.24

Factors

17.23.9

Introduction to Health and Safety at Work Regulation 2(1) Do the Regulations apply, i.e does the work involve maual handling operations? Regulation 4(1)(a)

No

Yes No Is there a risk of injury? Yes/possibly Yes

Is it reasonably practicable to avoid moving the load? No

Is it reasonably practicable to automate or mechanize the operation?

Regulation 4(1)(b)(i)

Yes

Does some risk of manual handling injury remain?

No

No

Yes/possibly Carry out manual handling assessment Regulation 4(1)(b)(ii) Determine measure to reduce risk of injury to lowest level reasonably practicable

Implement measures

Yes

Is risk of injury suffciently reduced? No

No

Review as necessary

Regulation 4(2)

Figure 17.6

Manual Handling Operations Regulations – flow chart.

17.24.2 Exposure limit values and action levels – Regulation 4

➤ the maximum noise (peak sound pressure) to which employees are exposed in a working day.

The Noise at Work Regulations require employers to take speciﬁc action at certain action values. These relate to:

The values are:

➤ the levels of exposure to noise of their employees averaged over a working day or week, and

370

➤ lower exposure action values: ➤ daily or weekly exposure of 80 dB (A-weighted) ➤ peak sound pressure of 135 dB (C-weighted)

Summary of the main legal requirements Assess the risk Identify noise hazards Estimate likely exposure to noise Identify meaures required to eliminate or reduce risks, control exposures and protect emloyees Make a record of what you will do in an action plan

Protect your employees Eliminate or control noise risks Eliminate or reduce risks using good practice and known control and management solutions For the higher-risk cases, plan and put in place technical and organisational noise-control measures

Worker information and training Consult workers and allow their participation Give employees information, instruction and training about the risks, control measures, hearing protection and safe working practices

Make sure the legal limits on noise exposure are not exceeded And provide hearing protection Protect your employees with hearing protection Make its use mandatory for the high-risk case (keep working on technical and organisational control measures) Manage the use of hearing protection with zones, instruction and supervision

Health surveillance Provide health surveillance (hearing checks) for those at risk Use the results to review controls and further protect individuals Employees co-operate and attend for hearing checks

Maintain and use the equipment Maintain any noise-control equipment and hearing protection Ensure that anything supplied is fully and properly used Employees use the controls provided and report any defects Employees use hearing protection where its use is mandatory

Review what you are doing Review as things change: Changes in work practices Key

Changes in noise exposures Employer actions

New ways to reduce risks

Employee actions

Figure 17.7

What needs to be done under the Control of Noise at Work Regulations 2005.

➤ upper exposure action values: ➤ daily or weekly exposure of 85 dB (A-weighted) ➤ peak sound pressure of 137 dB (C-weighted).

These exposure limit values take account of any reduction in exposure provided by hearing protection.

Figure 17.7 helps decide what needs to be done. There are also levels of noise exposure which must not be exceeded:

17.24.3

➤ exposure limit values: ➤ daily or weekly exposure of 87 dB (A-weighted) ➤ peak sound pressure of 140 dB (C-weighted).

Risk assessment – Regulation 5

If employees are likely to be exposed to noise at or above the lower exposure value a suitable and sufﬁcient assessment of the risks must be made. Decide whether any further action is needed, and plan how you will do it.

371

Introduction to Health and Safety at Work The risk assessment should: ➤ identify where there may be a risk from noise and who is likely to be affected ➤ contain a reliable estimate of employees’ exposures, and compare the exposure with the exposure action values and limit values ➤ identify what needs to be done to comply with the law, e.g. whether noise-control measures or hearing protection are needed, and, if so, where and what type, and ➤ identify any employees who need to be provided with health surveillance and whether any are at particular risk. The risk assessment should include consideration of: ➤ the level, type and duration of exposure, including ant exposure to peak sound pressure ➤ the effects of exposure to noise on employees or groups of employees whose health is at particular risk ➤ sfarp any effects on the health and safety of employees resulting from the interaction e.g. between noise and vibration ➤ any indirect effects from the interaction between noise and audible warnings ➤ manufacturers information ➤ availability of alternative equipment designed to reduce noise emissions ➤ any extension to noise exposure due to extended hours or in supervised rest facilities ➤ information following health surveillance ➤ availability of personal hearing protectors with adequate attenuation characteristics. It is essential that employers can show that their estimate of employees’ exposure is representative of the work that they do. It needs to take account of: ➤ the work they do or are likely to do ➤ the ways in which they do the work, and ➤ how it might vary from one day to the next. The estimate must be based on reliable information, e.g. measurements in their own workplace, information from other similar workplaces, or data from suppliers of machinery. Employers must record the signiﬁcant ﬁndings of their risk assessment. They need to record in an action plan anything identiﬁed as being necessary to comply with the law, setting out what they have done and what they are going to do, with a timetable and saying who will be responsible for the work. The risk assessment should be reviewed if circumstances in the workplace change and affect noise

372

exposures. Also it should be reviewed regularly to make sure that the employer continues to do all that is reasonably practicable to control the noise risks. Even if it appears that nothing has changed, employers should not leave it for more than about two years without checking whether a review is needed.

17.24.4

Elimination or control of exposure – Regulation 6

The purpose of the Noise at Work Regulations 2005 is to make sure that people do not suffer damage to their hearing – so controlling noise risks and noise exposure should be efforts are concentrated. Wherever there is noise at work employers should be looking for alternative processes, equipment and/or working methods which would make the work quieter or mean people are exposed for shorter times. They should also be keeping up with what is good practice or the standard for noise control within their industry. Where there are things that can be done to reduce risks from noise, that are reasonably practicable, they should be done. However, where noise exposures are below the lower exposure action values, risks are low and so employers would only be expected to take actions which are relatively inexpensive and simple to carry out. Where the assessment shows that employees are likely to be exposed at or above the upper exposure action values, employers must put in place a planned programme of noise control. The risk assessment will have produced information on the risks and an action plan for controlling noise. Employers should use this information to: ➤ tackle the immediate risk, e.g. by providing hearing protection ➤ identify what is possible to control noise, how much reduction could be achieved and what is reasonably practicable ➤ establish priorities for action and a timetable (e.g. consider where there could be immediate beneﬁts, what changes may need to be phased in over a longer period of time and the number of people exposed to the noise in each case) ➤ assign responsibilities to people to deliver the various parts of the plan ➤ ensure the work on noise control is carried out ➤ check that what has been done has worked. Actions taken should be based on the general principles set out in the Management Regulations and should include consideration of: ➤ other working methods ➤ choice of appropriate work equipment emitting the least possible noise

Summary of the main legal requirements ➤ the design and layout of workplaces, work stations and rest facilities ➤ suitable and sufﬁcient information and training ➤ reduction of noise by technical means ➤ appropriate maintenance programmes ➤ limitation of the duration and intensity of exposure, and ➤ appropriate work schedules with adequate rest periods.

17.24.5

below the upper exposure level). Which is likely to mean that an employer needs to: ➤ put someone in authority in overall charge of issuing them and making sure replacements are readily available ➤ carry out spot checks to see that the rules are being followed and that hearing protection is being used properly ➤ ensure all managers and supervisors set a good example and wear hearing protection at all times when in hearing protection zones ➤ ensure only people who need to be there enter hearing protection zones and do not stay longer than they need to.

Hearing protection – Regulation 7

Hearing protection should be issued to employees: ➤ where extra protection is needed above what can been achieved using noise control ➤ as a short-term measure while other methods of controlling noise are being developed. Hearing protection should not be used as an alternative to controlling noise by technical and organisational means. Employers should consult with their employees or their representatives on the type of hearing protection to be used. Employers are required to: ➤ provide employees with hearing protectors if they ask for it and their noise exposure is between the lower and upper exposure action values ➤ provide employees with hearing protectors and make sure they use them properly when their noise exposure exceeds the upper exposure action values ➤ identify hearing protection zones, i.e. areas where the use of hearing protection is compulsory, and mark them with signs if possible. Restrict access to hearing protection zones where this is practicable and the noise exposures justiﬁes it ➤ provide employees with training and information on how to use and care for the hearing protectors ➤ ensure that the hearing protectors are properly used and maintained.

17.24.6 Maintenance and use of equipment – Regulation 8 Employers need to make sure that hearing protection works effectively and to: ➤ check that all equipment provided in compliance with the regulations remains in good, clean condition and that there are no unofﬁcial modiﬁcations ➤ check that hearing protection is fully and properly used (except where it is provided for employees who are exposed at or above the lower exposure but

17.24.7

Health surveillance – Regulation 9

Employers must provide health surveillance (hearing checks) for all their employees who are likely to be regularly exposed above the upper exposure action values, or are at risk for any reason, e.g. they already suffer from hearing loss or are particularly sensitive to damage. The purpose of health surveillance is to: ➤ warn when employees might be suffering from early signs of hearing damage ➤ give employers an opportunity to do something to prevent the damage getting worse ➤ check that control measures are working. Trade union safety representative, or employee representative and the employees concerned should be consulted before introducing health surveillance. It is important that employees understand that the aim of health surveillance is to protect their hearing. Employers will need their understanding and co-operation if health surveillance is to be effective. Health surveillance for hearing damage usually means: ➤ regular hearing checks in controlled conditions ➤ telling employees about the results of their hearing checks (required after reasonable notice by employee) ➤ keeping health records ➤ ensuring employees are examined by a doctor where hearing damage is identiﬁed. If the doctor considers the hearing damage is likely to be the result of exposure, the employer must ensure that: ➤ ➤ ➤ ➤

employee is informed by a suitably qualiﬁed person review the risk assessment and control measures consider assigning employee to alternative work ensure continued surveillance.

373

Introduction to Health and Safety at Work

17.25 Personal Protective Equipment at Work Regulations 1992 as amended in 2002

17.24.8 Information, instruction and training – Regulation 10 Where employees are exposed to noise which is likely to be at or above the lower exposure level, suitable and sufﬁcient information, instruction and training must be provided and kept up to date. This includes the nature of the risks, compliance action taken, signiﬁcant ﬁndings of the risk assessment, hearing protection, how to detect and report signs of hearing damage, entitlement to health surveillance, safe working practices and collective results of health surveillance.

17.24.9

References

Control of Noise at Work Regulations 2005 (SI No 1643). Controlling Noise at Work. The Control of Noise At Work Regulations 2005, L108 (second edition), 2005 HSE Books ISBN 0-7176-6164-4 Noise at Work. Guidance for employers on the Control of Noise at Work Regulations 2005 INDG362 (rev1), 2005 HSE Books ISBN 0-7176-6165-2 Sound solutions Techniques to reduce noise at work HSG138 1995, HSE Books ISBN 0-7176-0791-7 Ear Protection Employers duties explained. INDG298, 1999 HSE Books Protect your hearing or loose it! INDG363 (rev1) 2005 HSE BOOKS ISBN 0-7176-6166-0

17.25

Personal Protective Equipment at Work Regulations 1992 as amended in 2002

17.25.1

Introduction

Ordinary working clothes and uniforms, which do not speciﬁcally protect against risks to health and safety, and protective equipment worn in sports’ competitions are not covered. Where there is overlap in the duties in these Regulations and those covering lead, ionizing radiations, asbestos, hazardous substances (COSHH), noise, and construction head protection then the speciﬁc legislative requirements should prevail.

17.25.2

Every employer shall ensure that suitable PPE is provided to their employees who may be exposed to risks to their health and safety except where it has been adequately or more effectively controlled by other means. (Management Regulations require PPE to be the last choice in the principles of protection.) PPE shall not be suitable unless: ➤ it is appropriate for the risks and the conditions of use including the period for which it is worn ➤ it takes account of ergonomic requirements and the state of health of the wearer and the characteristics of the workstation of each person ➤ it is capable of ﬁtting the wearer correctly, by adjustments if necessary ➤ it is, so far as is practicable, able to combat the risks without increasing overall risks ➤ it complies with UK legislation on design or manufacture, i.e. it has a CE marking. Where it is necessary that PPE is hygienic and otherwise free of risk to health PPE must be provided to a person solely for their individual use.

17.25.3 The effect of the Personal Protective Equipment (PPE) at Work regulations is to ensure that certain basic duties governing the provision and use of PPE apply to all situations where PPE is required. The Regulations follow sound principles for the effective and economical use of PPE, which all employers should follow. PPE, as deﬁned, includes all equipment (including clothing affording protection against the weather), which is intended to be worn or held by a person at work and which protects them against one or more risks to their health and safety. Waterproof, weatherproof or insulated clothing is covered only if its use is necessary to protect against adverse climatic conditions.

374

Provision of PPE – Regulation 4

Compatibility – Regulation 5

Where more than one health and safety risk necessitates the wearing of multiple PPE simultaneously then they shall be compatible and remain effective.

17.25.4

Assessment – Regulation 6

Before choosing any PPE, employers must ensure that an assessment is made to determine whether the PPE is suitable. The assessment shall include: ➤ assessing risks which have not been avoided by other means

Summary of the main legal requirements ➤ a deﬁnition of the characteristics that PPE must have to be effective, taking into account any risks created by the PPE itself ➤ a comparison of available PPE with the required characteristics ➤ information on whether the PPE is compatible with any other PPE which is in use, and which an employee would be required to wear simultaneously. The assessment should be reviewed if it is no longer valid or there have been signiﬁcant changes. In simple cases it will not be necessary to record the assessment but, in more complex cases, written records should be made and kept readily available for future reference.

17.25.5

Maintenance – Regulation 7

Every employer (and self-employed person) shall ensure that any PPE provided is maintained, including replaced and cleaned, in an efﬁcient state, in efﬁcient working order and in good repair. The guide emphasizes the need to set up an effective system of maintenance for PPE. This should be proportionate to the risks and appropriate to the particular PPE. It could include, where appropriate, cleaning, disinfection, examination, replacement, repair and testing. For example, mechanical fall arrestor equipment or subaqua breathing apparatus will require planned preventative maintenance with examination, testing and overhaul. Records should be kept of the maintenance work. Gloves may only require periodic inspection by the user as necessary, depending on their use. Spare parts must be compatible and be the proper part suitably CE marked where applicable. Manufacturers’ maintenance schedules and instructions should be followed unless alternative schemes are agreed with the manufacturer or agent. In some cases these requirements can be fulﬁlled by using disposable PPE which can be discarded after use or when their life has expired. Users should know when to discard and replace disposable PPE.

17.25.7

Employers shall provide employees with adequate and appropriate information, instruction and training on: ➤ the risks which the PPE will avoid or limit ➤ the purpose for which and the manner in which PPE should be used ➤ any action required of the employee to maintain the PPE. Employers must ensure that the information is kept available. The employer shall where appropriate and at suitable intervals, organize demonstrations of the wearing of PPE. The guidance suggests the training should include: ➤ an explanation of the risks and why PPE is needed ➤ the operation, performance and limitations of the equipment ➤ instructions on the selection, use and storage of PPE ➤ problems that can affect PPE relating to other equipment, working conditions, defective equipment, hygiene factors and poor ﬁt ➤ the recognition of defects and how to report problems with PPE ➤ practice in putting on wearing and removing PPE ➤ practice in user cleaning and maintenance ➤ how to store safely.

17.25.8

Use and reporting of defects – Regulations 10 and 11

Every employer shall take all reasonable steps to ensure that PPE is properly used. Every employee shall: ➤ use PPE provided in accordance with training and instructions ➤ return it to the accommodation provided after use ➤ report any loss or obvious defect.

17.25.9 17.25.6

Information, instruction and training – Regulation 9

References

Accommodation – Regulation 8

When an employer or self-employed person has to provide PPE they must ensure that appropriate accommodation is provided to store it when not in use. The type of accommodation will vary and may just be suitable hooks for special clothing and small portable cases for goggles. It should be separate from normal outer clothing storage arrangements and protect the PPE from contamination or deterioration.

Personal Protective Equipment (EC Directive) Regulations 1992. SI 1992 No 3139, Stationary Ofﬁce Personal protective equipment at work,. Personal Protective Equipment at Work Regulations 1992. Guidance on Regulations. L25, 1992 HSE Books ISBN 0-7176-0415-2 A short guide to the Personal Protective Equipment at Work Regulations 1992, INDG174 1997 HSE Books ISBN 0-7176-0889-1

375

17.26 Provision and Use of Work Equipment Regulations 1998 (except part IV) as amended in 2002

Introduction to Health and Safety at Work Sun protection Advice for employers of outdoor workers. INDG337, HSE Books 2001 ISBN 0-7176-1982-6

17.26.4

Suitability of work equipment – Regulation 4

Work equipment:

17.26

Provision and Use of Work Equipment Regulations 1998 (except part IV) as amended in 2002

17.26.1

Introduction

The Provision and Use of Work Equipment Regulations 1998 (PUWER) are made under the HSW Act and their primary aim is to ensure that work equipment is used without risks to health and safety, regardless of its age, condition or origin. The requirements of PUWER that are relevant to woodworking machinery are set out in the Safe use of woodworking machinery Approved Code of Practice. PUWER has speciﬁc requirements for risk assessment which are covered under the Health and Safety Management Regulations 1999. Part IV of PUWER is concerned with power presses and is not part of the Certiﬁcate syllabus and is therefore not covered in this summary.

17.26.2

Definitions

Work equipment means any machinery, appliance, apparatus, tool or installation for use at work. Use in relation to work equipment means any activity involving work equipment and includes starting, stopping, programming, setting, transporting, repairing, modifying, maintaining, servicing and cleaning.

17.26.3

Duty holders – Regulation 3

➤ has to be constructed or adapted so that it is suitable for its purpose ➤ it has to be selected with the conditions of use and the users’ health and safety in mind ➤ it may only be used for operations for which, and under conditions for which it is suitable. This covers all types of use and conditions and must be considered for each particular use or condition. For example, scissors may be safer than knives with unprotected blades and should therefore be used for cutting operations where practicable; risks imposed by wet, hot or cold conditions must be considered.

17.26.5

Maintenance – Regulation 5

The regulation sets out the general requirement to keep work equipment maintained in: ➤ an efﬁcient state ➤ efﬁcient working order ➤ good repair. Compliance involves all three criteria. In addition, where there are maintenance logs for machinery, they must be kept up to date. In many cases this will require routine and planned preventive maintenance of work equipment. When checks are made priority must be given to: ➤ safety ➤ operating efﬁciency and performance ➤ the equipment’s general condition.

17.26.6

Inspection – Regulation 6

Under PUWER the following groups of people have duties placed on them:

Where the safety of work equipment depends on the installation conditions, it must be inspected:

➤ employers ➤ the self-employed ➤ people who have control of work equipment, for example plant hire companies.

➤ after installation and before being put into service for the ﬁrst time ➤ after assembly at a new site or in a new location ➤ to ensure that it has been installed correctly and is safe to operate.

In addition to all places of work, the Regulations apply to common parts of shared buildings, industrial estates and business parks; to temporary works sites including construction; to home working (but not to domestic work in a private household); to hotels, hostels and sheltered accommodation.

Where work equipment is exposed to conditions causing deterioration which is liable to result in dangerous situations it must be inspected:

376

➤ at suitable intervals ➤ when exceptional circumstances occur.

Summary of the main legal requirements Inspections must be determined and carried out by competent persons. An inspection will vary from a simple visual external inspection to a detailed comprehensive inspection which may include some dismantling and/or testing. However, the level of inspection would normally be less than that required for a thorough examination under, for example, LOLER for certain items of lifting equipment. Records of inspections must be kept with sufﬁcient information to properly identify the equipment, its normal location, dates, faults found, action taken, to whom faults were reported, who carried out the inspection, when repairs were made, date of the next inspection. When equipment leaves an employer’s undertaking it must be accompanied by physical evidence that the last inspection has been carried out.

17.26.7

Specific risks – Regulation 7

Where the use of work equipment involves speciﬁc hazards, its use must be restricted to those persons given the speciﬁc task of using it and repairs, etc. must be restricted to designated persons. Designated persons must be properly trained to fulﬁll their designated task. Hazards must be controlled using a hierarchy of control measures, starting with elimination where this is possible, then considering hardware measures such as physical barriers and, lastly, software measures such as a safe system of work.

December 1992, conforms at all times with the relevant essential requirements in various European Directives made under Article 100A (now 95) of the Treaty of Rome. The requirements of PUWER 98 Regulations 11 to 19 and 22 to 29 only apply if the essential requirements do not apply to a particular piece of equipment. However, PUWER regulations 11–19 and 22–29 will apply if: ➤ they include requirements which were not included in the relevant product legislation ➤ the relevant product legislation has not been complied with (e.g. the guards ﬁtted on a machine when supplied were not adequate). Employers using work equipment need to check that any new equipment has been made to the requirements of the relevant Directive, has a CE marking, suitable instructions and a Certiﬁcate of Conformity. The Machinery Directive was brought into UK law by the Supply of Machinery (Safety) Regulations 1992 as amended, which duplicate PUWER regulations 11–19 and 22–29. The employer still retains the duty to ensure that the equipment is safe to use.

17.26.10

Dangerous parts of machinery – Regulation 11

Measures have to be taken which:

17.26.8 Information, instruction and training – Regulations 8 and 9 Persons who use work equipment must have adequate: ➤ health and safety information ➤ where appropriate, written instructions about the use of the equipment ➤ training for health and safety in methods which should be adopted when using the equipment, any hazards and precaution which should be taken to reduce risks. Any persons who supervise the use of work equipment should also receive information, instruction and training. The training of young persons is especially important with the need for special risk assessments under the Management Regulations. Health and safety training should take place within working hours.

17.26.9 Conformity with Community requirements – Regulation 10 The intention of this regulation is to require that employers ensure that equipment, provided for use after 31

➤ prevent access to any dangerous part of machinery or to any rotating stock-bar ➤ stop the movement of any dangerous part of machinery or rotating stock-bar before any part of a person enters a danger zone. The measures required follow the normal hierarchy and should be considered to the extent that it is practicable in each case. They consist of: ➤ the provision of ﬁxed guards enclosing every dangerous part of machinery ➤ the provision of other guards or protection devices ➤ the provision of jigs, holders, push-sticks or similar protection appliances used in conjunction with the machinery ➤ Plus the provision of information, instruction, training and supervision as is necessary. All guards and protection devices shall: ➤ be suitable for its purpose ➤ be of good construction, sound material and adequate strength

377

Introduction to Health and Safety at Work ➤ be maintained in an efﬁcient state, in efﬁcient working order and in good repair ➤ not give rise to increased risks to health and safety ➤ not be easily bypassed or disabled ➤ be situated at sufﬁcient distance from the danger zone ➤ not unduly restrict the view of the operating cycle of the machine where this is relevant ➤ be so constructed or adapted that they allow operations necessary to ﬁt or replace parts and for maintenance work, if possible without having to dismantle the guard or protection device.

not apply to the normal operating cycle of an automatic device. Where appropriate, one or more readily accessible Stop controls shall be provided to bring the work equipment to a safe condition in a safe manner (Regulation 15). They must:

17.26.11 Protection against specified hazards – Regulation 12

Where appropriate one or more readily accessible emergency stop controls (Regulation 16) must be provided unless it is not necessary:

Exposure to health and safety risks from the following hazards must be prevented or adequately controlled: ➤ any article falling or being ejected from work equipment ➤ rupture or disintegration of work equipment ➤ work equipment catching ﬁre or overheating ➤ the unintended or premature discharge of any article, or of any gas, dust, liquid, vapour or other substance which is produced, used or stored in the work equipment ➤ the unintended or premature explosion of the work equipment or any article or substance produced, used or stored in it.

17.26.12 High or very low temperature – Regulation 13 Work equipment and any article or substance produced, used or stored in work equipment which is at a high or very low temperature must have protection to prevent injury by burn, scald or sear. This does not cover risks such as from radiant heat or glare. Engineering methods of control such as insulation, doors, temperature control, guards etc. should be used where practicable but, there are some cases, like cooker hot plates, where this is not possible.

17.26.13

Controls – Regulations 14 to 18

Where work equipment is provided with (Regulation 14): ➤ starting controls (including restarting after a stoppage) ➤ controls which change speed, pressure or other operating condition which would affect health and safety it should not be possible to perform any operation except by a deliberate action on the control. This does

378

➤ bring the work equipment to a complete stop where necessary ➤ if necessary switch off all sources of energy after stopping the functioning of the equipment ➤ operate in priority to starting or operating controls.

➤ by the nature of the hazard ➤ by the time taken for the stop controls to bring the equipment to a complete stop. Emergency stop controls must have priority over stop controls. They should be provided where other safeguards are not adequate to prevent risk when something irregular happens. They should not be used as a substitute for safeguards or the normal method of stopping the equipment. All controls for work equipment shall (Regulation 17): ➤ be clearly visible and identiﬁable including appropriate marking where necessary ➤ not expose any person to a risk to their health and safety except where necessary. Where appropriate employers shall ensure that: ➤ controls are located in a safe place ➤ systems of work are effective in preventing any person being in a danger zone when equipment is started ➤ an audible, visible or other suitable warning is given whenever work equipment is about to start. Persons in a danger zone as a result of starting or stopping equipment must have sufﬁcient time and suitable means to avoid any risks. Control systems (Regulation 18) must be safe and chosen so as to allow for failures, faults and constraints. They must: ➤ not create any increased risk to health and safety ➤ not result in additional or increased risks when failure occurs ➤ not impede the operation of any stop or emergency stop controls.

Summary of the main legal requirements 17.26.14 Isolation from sources of energy – Regulation 19 Work equipment must be provided with readily accessible and clearly identiﬁed means to isolate it from all sources of energy. Re-connection must not expose any person using the equipment to any risks. The main purpose is to allow equipment to be made safe under particular circumstances, such as maintenance, when unsafe conditions occur, or when adverse conditions such as electrical equipment in a ﬂammable atmosphere or wet conditions occur. If isolation may cause a risk in itself, special precautions must be taken; for example, a support for a hydraulic press tool which could fall under gravity if the system is isolated.

17.26.15

Stability – Regulation 20

Work equipment must be stabilized by clamping or otherwise as necessary to ensure health and safety. Most machines used in a ﬁxed position should be bolted or fastened so that they do not move or rock in use.

17.26.16

Lighting – Regulation 21

Suitable and sufﬁcient lighting, taking account of the operations being carried out, must be provided where people use work equipment. This will involve general lighting and in many cases local lighting, such as on a sewing machine. If access for maintenance is required regularly, permanent lighting should be provided.

17.26.17 Maintenance operations – Regulation 22 So far as is reasonably practicable work equipment should be constructed or adapted to allow maintenance operations to be: ➤ conducted while they are shut down ➤ undertaken without exposing people to risk ➤ carried out after appropriate protection measures have been taken.

17.26.18 Markings and warnings – Regulations 23 and 24 Work equipment should have all appropriate markings for reasons of health and safety made in a clearly visible manner. For example, the maximum safe working load,

stop and start controls, or the maximum rotation speed of an abrasive wheel. Work equipment must incorporate warnings or warning devices as appropriate, which are unambiguous, easily perceived and easily understood. They may be incorporated in systems of work, a notice, a ﬂashing light or an audible warning. They are an active instruction or warning to take speciﬁc precautions or actions when a hazard exists.

17.26.19

Part III, Mobile work equipment – Regulations 25–30

The main purpose of this section is to require additional precautions relating to work equipment while it is travelling from one location to another or where it does work while moving. If the equipment is designed primarily for travel on public roads, the Road Vehicles (Construction and Use) Regulations 1986 will normally be sufﬁcient to comply with PUWER 98. Mobile equipment would normally move on wheels, tracks, rollers, skids, etc. Mobile equipment may be selfpropelled, towed or remote controlled and may incorporate attachments. Pedestrian-controlled work equipment such as lawn mowers is not covered by Part III.

Employees carried on mobile work equipment – Regulation 25 No employee may be carried on mobile work equipment unless: ➤ it is suitable for carrying persons ➤ it incorporates features to reduce risks as low as is reasonably practicable, including risks from wheels and tracks.

Rolling over of mobile work equipment – Regulations 26 Where there is a risk of overturning it must be minimized by: ➤ stabilizing the equipment ➤ ﬁtting a structure so that it only falls on its side, (tip over protection structure such as as the vertical mast of a fork lift truck) ➤ ﬁtting a structure which gives sufﬁcient clearance for anyone being carried if it turns over further, ROPS (roll over protection structures) ➤ a device giving comparable protection ➤ ﬁtting a suitable restraining system for people if there is a risk of being crushed by rolling over. This Regulation does not apply: ➤ to a fork truck ﬁtted with ROPS or vertical mast which prevents it turning on its side

379

Introduction to Health and Safety at Work

17.27

The Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995

➤ where it would increase the overall risks ➤ where it would not be reasonably practicable to operate equipment ➤ to any equipment provided for use before 5 December 1998.

Overturning of fork lift trucks – Regulation 27 Fork lift trucks, which carry an employee, must be adapted or equipped to reduce the risk to safety from overturning to as low as is reasonably practicable.

Self-propelled work equipment – Regulation 28 Where self-propelled work equipment may involve risks while in motion they shall have: ➤ facilities to prevent unauthorized starting ➤ (with multiple rail-mounted equipment) facilities to minimize the consequences of collision ➤ a device for braking and stopping ➤ (where safety constraints so require) emergency facilities for braking and stopping, in the event of failure of the main facility, which have readily accessible or automatic controls ➤ (where the driver’s vision is inadequate) devices ﬁtted to improve vision ➤ (if used at night or in dark places) appropriate lighting ﬁtted or otherwise it shall be made sufﬁciently safe for its use ➤ if there is anything carried or towed that constitutes a ﬁre hazard liable to endanger employees (particularly if escape is difﬁcult such as from a tower crane) appropriate ﬁre-ﬁghting equipment carried, unless it is sufﬁciently close by.

Remote-controlled self-propelled work equipment – Regulation 29 Where remote-controlled self-propelled work equipment involves a risk while in motion it shall: ➤ stop automatically once it leaves its control range ➤ have features or devices to guard against the risk of crushing or impact.

Drive shafts – Regulation 30 Where seizure of the drive shaft between mobile work equipment and its accessories or anything towed is likely to involve a risk to safety: ➤ the equipment must have means to prevent a seizure ➤ where it cannot be avoided, every possible measures should be taken to avoid risks ➤ the shaft should be safeguarded from contacting the ground and becoming soiled or damaged.

380

17.26.20

Part IV: Power presses

Regulations 31–35 relate to power presses and are not included here as they are excluded from the NEBOSH Certiﬁcate syllabus. Details can be found in the Power Press ACOP.

17.26.21

References

Safe use of work equipment, Provision and Use of Work Equipment Regulations 1998, Approved Code of Practice and Guidance, HSC L22 1998 HSE Books, ISBN 0-7176-1626-6 PUWER 1998, Provision and Use of Work Equipment Regulations 1998: Open learning guidance, 1999 HSE Books ISBN 0-7176-2459-5 Simple guide to the Provision and Use of Work Equipment Regulations 1998, INDG291, 1999 HSE Books ISBN 0-7176-2429-3 Using work equipment safely INDG229, 2002 HSE Books ISBN 0-7176-2389-0 Hiring and leasing out of plant: application of PUWER 98, Regulations 26 and 27, HSE MISC156, 1998 HSE Books

17.27

The Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995

17.27.1

Introduction

These Regulations require the reporting of speciﬁed accidents, ill health and dangerous occurrences to the enforcing authorities. The events all arise out of or in connection with work activities covered by the HSW Act. They include death, major injury and more than three-day lost-time accidents. Schedules to the Regulations specify the details of cases of ill-health and dangerous occurrences. For most businesses reportable events will be quite rare and so there is little for them to do under these Regulations apart from keeping the guidance and forms available and being aware of the general requirements.

17.27.2

Definitions – Regulation 2

Accident includes an act of non-consensual physical violence done to a person at work. This means that injuries, through physical violence to people not at work, are not reportable. Neither is any injury that occurs between workers over a personal matter or is carried out by a visiting relative of a person

Summary of the main legal requirements at work to that person. However, if a member of the public causes injury to a person at work through physical violence, that is reportable. Incidents involving acts of violence may well be reportable to the police, which is outside the requirements of these Regulations.

17.27.3 Notification and reporting of major injuries and dangerous occurrences – Regulation 3 (1), 4 and Schedules 1 and 2 The HSE or Local Authority shall be notiﬁed immediately by the quickest practicable means and sent a report form F2508 (or other approved means) within 10 days following: (a) Death of a person as a result of an accident arising out of or in connection with work. Also if death occurs within one year of an accident, the Authorities must be informed (b) Major Injury to a person as a result of an accident arising out of or in connection with work (c) where a person not at work suffers an injury as a result of or in connection with work, and that person is taken from the site to hospital for treatment (d) where a person not at work suffers a major injury as a result of an accident arising out of or in connection with work at a hospital

17.27.6

Local Authorities are responsible for retailing, some warehouses, most ofﬁces, hotels and catering, sports, leisure, consumer services, and places of worship. The HSE are responsible for all other places of work.

17.27.7

Major injuries Schedule 1 1. 2. 3. 4. 5. 6.

7.

8. 9.

Where a person at work is incapacitated for work of a kind which they might reasonably be expected to do, either under their own contract of employment or in the normal course of employment, for more than three consecutive days (excluding the day of the accident, but including any days which would not have been working days) because of an injury resulting from an accident at work, the responsible person shall within 10 days send a report on form F2508 or other approved form, unless it has been reported under Regulation 3 (1) as a Major Injury, etc.

17.27.5 Reporting of cases of disease – Regulation 5

10.

Any fracture, other than to the ﬁngers, thumbs or toes Any amputation Dislocation of the shoulder, hip, knee or spine Loss of sight (whether temporary or permanent) A chemical or hot metal burn to the eye or any penetrating injury to the eye Any injury resulting from an electric shock or electrical burn (including any electrical burn caused by arcing or arcing products) leading to unconsciousness or requiring resuscitation or admittance to hospital for more than 24 hours Any other injury (a) leading to hypothermia, heat-induced illness or to unconsciousness (b) requiring resuscitation (c) requiring admittance to hospital for more than 24 hours Loss of consciousness caused by asphyxia or by exposure to a harmful substance or biological agent Either of the following conditions which result from the absorption of any substance by inhalation, ingestion or through the skin (a) acute illness requiring medical treatment (b) loss of consciousness Acute illness which requires medical treatment where there is reason to believe that this resulted from exposure to a biological agent or its toxins or infected material.

17.27.9

Dangerous occurrences – Schedule 2 summary

PART I General 1.

Where a medical practitioner notiﬁes the employer’s responsible person that an employee suffers from a reportable work-related disease, a completed disease report form (F2508A) should be sent to the enforcing authority. The full list is contained in schedule 3 to the regulations which is summarized in this guide.

Records

A record of each incident reported must be kept at the place of business for at least 3 years.

where there is a dangerous occurrence.

17.27.4 Reporting of three-day plus accidents – Regulation 3 (2)

Which enforcing authority?

2.

Lifting machinery, etc. The collapse, overturning, or the failure of any loadbearing part of lifts and lifting equipment. Pressure systems The failure of any closed vessel or of any associated pipe-work, in which the internal pressure was above or below atmospheric pressure.

381

Introduction to Health and Safety at Work 3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

Freight containers The failure of any freight container in any of its loadbearing parts. Overhead electric lines Any unintentional incident in which plant or equipment comes into contact with overhead power lines. Electrical short circuit Electrical short circuit or overload attended by ﬁre or explosion. Explosives The unintentional explosion or ignition of explosives, misﬁre, the failure of the shots in any demolition operation to cause the intended extent of collapse, the projection of material beyond the boundary of the site, any injury to a person resulting from the explosion or discharge of any explosives or detonator. Biological agents Any accident or incident which resulted, or could have resulted, in the release or escape of a biological agent likely to cause severe human infection or illness. Malfunction of radiation generators, etc. Any incident in which the malfunction of a radiation generator or its ancillary equipment used in ﬁxed or mobile industrial radiography, the irradiation of food or the processing of products by irradiation, causes it to fail to de-energize at the end of the intended exposure period; or to fail to return to its safe position at the end of the intended exposure period. Breathing apparatus Any incident in which breathing apparatus malfunctions while in use, or during testing immediately prior to use. Diving operations In relation to a diving project the failure or the endangering of diving equipment, the trapping of a diver, any explosion in the vicinity of a diver, any uncontrolled ascent or any omitted decompression. Collapse of scaffolding The complete or partial collapse of any scaffold which is more than 5 m in height; erected over or adjacent to water, in circumstances such that there would be a risk of drowning to a person falling from the scaffold into the water; or the suspension arrangements of any slung or suspended scaffold which causes a working platform or cradle to fall. Train collisions Any unintended collision of a train with any other train or vehicle. Wells Any dangerous occurrence at a well other than a well sunk for the purpose of the abstraction of water. Pipelines or pipeline works A dangerous occurrence in respect of a pipeline or pipeline works.

382

15. Fairground equipment The failure of any load-bearing part or the derailment or the unintended collision of cars or trains. 16. Carriage of dangerous substances by road Any incident involving a road tanker or tank container used for the carriage of dangerous goods in which the tanker overturns, is seriously damaged, there is an uncontrolled release or there is a ﬁre. Dangerous occurrences which are reportable except in relation to offshore workplaces 17. Collapse of building or structure Any unintended collapse or partial collapse of any building or structure: under construction; reconstruction; alteration or demolition which involves a fall of more than 5 tonnes of material; any ﬂoor or wall of any building; or any false-work. 18. Explosion or fire An explosion or ﬁre occurring in any plant or premises which results in the suspension of normal work for more than 24 hours. 19. Escape of flammable substances The sudden, uncontrolled release inside a building: (i) of 100 kg or more of a ﬂammable liquid (ii) of 10 kg or more of a ﬂammable liquid above its boiling point (iii) of 10 kg or more of a ﬂammable gas 500 kg or more of any of the substances, if released in the open air. 20. Escape of substances The accidental release or escape of any substance in a quantity sufﬁcient to cause the death, major injury or any other damage to the health of any person.

17.27.10

Reportable diseases – Schedule 3, brief summary

These include: ➤ certain poisonings ➤ some skin diseases such as occupational dermatitis, skin cancer, chrome ulcer, oil folliculitis/acne ➤ lung diseases, such as occupational asthma, farmer’s lung, pneumoconiosis, asbestosis, mesothelioma ➤ infections such as leptospirosis, heptatitis, tuberculosis, anthrax, legionellosis and tetanus ➤ other conditions, such as occupational cancer, certain musculoskeletal disorders, decompression illness and hand-arm vibration syndrome. The details can be checked by consulting the guide, looking at the pad of report forms, checking the HSE’s web site, ringing the HSE’s Infoline or the Incident Control Centre (ICC).

Summary of the main legal requirements 17.27.11

References

Safety representatives must be afforded time off with pay to fulﬁll these functions and to undergo training.

Employers’ duties – Regulation 4a

Every employer shall consult safety representatives in good time regarding:

17.28

Safety Representatives and Safety Committees Regulations 1977

These Regulations, made under the HSW ACT Section 2 (4), prescribe the cases in which recognized trade unions may appoint safety representatives, specify the functions of such representatives, and set out the obligations of employers towards them. Employers’ obligations to consult non-union employees are contained in the Health and Safety (Consultation with Employees) Regulations 1996.

17.28.1

Appointment – Regulation 3

A recognized trade union may appoint safety representatives from among employees in all cases where one or more employees are employed. When the employer is notiﬁed in writing the safety representatives have the functions set out in Regulation 4. A person ceases to be a safety representative when: ➤ the appointment is terminated by the trade union ➤ they resign ➤ employment ceases. A safety representative should have been with the employer for two years or have worked in similar employment for at least two years.

17.28.2

Functions – Regulation 4

These are functions and not duties. They include: ➤ representing employees in consultation with the employer ➤ investigating potential hazards and dangerous occurrences ➤ investigating the causes of accidents ➤ investigating employee complaints relating to health, safety and welfare ➤ making representations to the employer on health safety and welfare matters ➤ carrying out inspections

➤ the introduction of any measure which may affect health and safety ➤ the arrangements for appointing or nominating competent person (s) under the Management Regulations ➤ any health and safety information required for employees ➤ the planning and organizing of any health and safety training for employees ➤ the health and safety consequences of introducing new technology. Employers must provide such facilities and assistance as safety representatives may reasonably require to carry out their functions.

17.28.4

Inspections – Regulations 5 and 6

Following reasonable notice in writing, safety representatives may inspect the workplace every quarter (or more frequently by agreement with the employer). They may inspect the workplace at any time, after consultation, when there have been substantial changes in the conditions of work or there is new information on workplace hazards published by the HSC or HSE. Following an injury, disease or dangerous occurrence subject to Reporting of Injuries Diseases and Dangerous Occurrences Regulations, and after notifying the employer, where it is reasonably practicable to do so, safety representatives may inspect the workplace if it is safe. Employers must provide reasonable assistance and facilities, including provision for independent investigation and private discussion with employees. The employer may be present in the workplace during inspections.

17.28.5

Information – Regulation 7

Having given reasonable notice to the employer, safety representatives are entitled to inspect and take copies of any relevant statutory documents (except any health record of an identiﬁed person).

383

Safety Representatives and Safety Committees Regulations 1977

17.28.3

17.28

A guide to the Reporting of Injuries, Diseases and Dangerous Occurrences Regulations 1995, L73, 1999 HSE Books ISBN 0-7176-2431-5 Everyone’s guide to RIDDOR, HSE 31 (rev1) HSE Books ISBN0-7176-2441-2 RIDDOR Information for doctors HSE 32. 1996 HSE Books, RIDDOR reporting: Information about the new incident centre, MISC310, HSE

➤ representing employees at the workplace in consultation with enforcing inspectors ➤ receiving information ➤ attending safety committee meetings.

Introduction to Health and Safety at Work An exempt document is one: ➤ which could endanger national security ➤ which could cause substantial commercial injury on the employer ➤ contravenes a prohibition ➤ that relates to an individual without their consent ➤ which has been obtained speciﬁcally for legal proceedings.

17.29

Health and Safety (Safety Signs and Signals) Regulations 1996

17.28.6

➤

➤

Safety committees – Regulation 9

When at least two safety representatives have requested in writing that a safety committee is set up, the employer has three months to comply. The employer must consult with the safety representatives and post a notice stating its composition and the workplaces covered by it, in a place where it can be easily read by employees. The guidance gives details on the composition and running of safety committees.

➤

➤

means of a signboard, a safety colour, an illuminated sign, an acoustic sign, a verbal communication or a hand signal. ‘Signboard’ means a sign which provides information or instructions by a combination of geometric shape, colour and a symbol or pictogram and which is rendered visible by lighting of sufﬁcient intensity. ‘Hand signal’ means a movement or position of the arms or hands or a combination, in coded form, for guiding persons who are carrying out manoeuvres which create a risk to the health and safety of people at work. ‘Acoustic signal’ means a coded sound signal which is released and transmitted by a device designed for that purpose, without the use of a human or artiﬁcial voice. ‘Verbal communication’ means a predetermined spoken message communicated by a human or artiﬁcial voice.

17.29.3 17.28.7

Complaints – Regulation 11

If the employer fails to permit safety representatives time off or fails to pay for time off, complaints can be made to an industrial tribunal within 3 months of the incident.

17.28.8

References

HSC, Safety Representatives and safety committees (The Brown Book) Approved Code of Practice and Guidance on the Regulations, third edition, L87, 1996 HSE Books ISBN0-7176-1220-1

The Regulations require employers to use and maintain a safety sign where there is a signiﬁcant risk to health and safety that has not been avoided or controlled by other means, like engineering controls or safe systems of work, and where the use of a sign can help reduce the risk. They apply to all workplaces and to all activities where people are employed, but exclude signs used in connection with transport or the supply and marketing of dangerous substances, products and equipment. The Regulations require, where necessary, the use of road trafﬁc signs in workplaces to regulate road trafﬁc.

17.29.4

17.29

17.29.1

Health and Safety (Safety Signs and Signals) Regulations 1996 Introduction

These regulations came into force in April 1996. The results of the risk assessment made under the Management of Health Safety at Work Regulations will have identiﬁed situations where there may be a residual risk when warnings or further information are necessary. If there is no signiﬁcant risk there is no need to provide a sign.

Provision and maintenance of safety signs – Regulation 4

Information, instruction and training – Regulation 5

Every employer shall ensure that: ➤ comprehensible and relevant information on the measures to be taken in connection with safety signs is provided to each employee ➤ each employee receives suitable and sufﬁcient instruction and training in the meaning of safety signs.

17.29.5

Functions of Colours, Shapes and Symbols in Safety Signs

Safety colours

17.29.2

Definitions – Regulation 2

➤ ‘Safety sign’ means a sign referring to a speciﬁc object, activity or situation and providing information or instruction about health and safety at work by

384

Red Red is a safety colour and must be used for any: ➤ prohibition sign concerning dangerous behaviour (e.g. the safety colour on a ‘No Smoking’ sign). Prohibition

Summary of the main legal requirements signs must be round, with a black pictogram on a white background with red edging and a red diagonal line (top left, bottom right). The red part must take up at least 35% of the area of the sign ➤ danger alarm concerning stop, shutdown, emergency cut out devices, evacuate (e.g. the safety colour of an emergency stop button on equipment) ➤ ﬁre-ﬁghting equipment.

safety colour on a ‘Safety Helmet Must Be Worn’ sign or a ‘Pedestrians Must Use This Route’ sign). Mandatory signs must be round, with a white pictogram on a blue background. The blue part must take up at least 50% of the area of the sign.

Ear protection must be worn No forklift trucks

No smoking

Red and white alternating stripes may be used for marking surface areas to show obstacles or dangerous locations.

Yellow Yellow (or amber) is a safety colour and must be used for any warning sign concerning the need to be careful, take precautions, examine or the like (e.g. the safety colour on hazard signs, such as for ﬂammable material, electrical danger, etc). Warning signs must be triangular, with a black pictogram on a yellow (or amber) background with black edging. The yellow (or amber) part must take up at least 50% of the area of the sign.

General danger

Eye protection must be worn

Green Green is a safety colour and must be used for emergency escape signs (e.g. showing emergency doors, exits and routes) and ﬁrst aid signs (e.g. showing location of ﬁrst aid equipment and facilities). Escape and ﬁrst aid signs must be rectangular or square, with a white pictogram on a green background. The green part must take up at least 50% of the area of the sign. So long as the green takes up at least 50% of the area, it is sometimes permitted to use a green pictogram on a white background, for example where there is a green wall and the reversal provides a more effective sign than one with a green background and white border; no danger (e.g. for ‘return to normal’).

Explosive

Yellow and black alternating stripes may be used for marking surface areas to show obstacles or dangerous locations.

Means of Escape

First Aid

Other colours White White is not a safety colour but is used for: pictograms or other symbols on blue and green signs; in alternating red and white stripes to show obstacles or dangerous locations; in continuous lines showing trafﬁc routes.

Yellow may be used in continuous lines showing trafﬁc routes.

Blue Blue is a safety colour and must be used for any mandatory sign requiring speciﬁc behaviour or action (e.g. the

Black Black is not a safety colour but is used for: pictograms or other symbols on yellow (or amber) signs and, except for ﬁre signs, red signs; in alternating yellow and black stripes to show obstacles or dangerous locations.

385

Introduction to Health and Safety at Work

17.30

Supply of Machinery (Safety) Regulations 1992

Shapes Round signs must be used for any prohibition (red) sign; mandatory (blue) sign. Triangular signs must be used for any warning (yellow or amber) sign. Square or rectangular signs must be used for any emergency escape sign and any ﬁrst aid sign.

Pictograms and other symbols The meaning of a sign (other than verbal communication) must not rely on words. However, a sign may be supplemented with words to reinforce the message provided the words do not in fact distract from the message or create a danger. A sign (other than verbal communication, acoustic signals or hand signals) should use a simple pictogram and/or other symbol (such as directional arrows, exclamation mark, etc) to effectively communicate its message and so overcome language barriers. Pictograms and symbols are included in the regulations. Employee training is needed to understand the meaning of these since many are not inherently clear, some are meaningless to anyone who has not had their meaning explained and some can even be interpreted with their opposite meaning. Pictograms and symbols included in the regulations do not cover all situations for which graphic representation of a hazard or other detail may be needed. Any sign used for a situation not covered in the Regulations, should include: ➤ either the international symbol for general danger (exclamation mark!). If the sign is a warning sign and tests show that the sign is effective ➤ in any other case a pictogram or symbol which has been tested and shown to be effective. The text of any words used to supplement a sign must convey the same meaning. For example, a round blue sign with a pictogram showing the white outline of a face with a solid white helmet on the head means ‘Safety Helmet Must Be Worn’ and so any text used must maintain the obligatory nature of the message

17.29.6

References

The Health and Safety (Safety Signs and Signals) Regulations 1996 SI 1996/341 Stationary Ofﬁce Safety Signs and Signals Guidance on the Regulations L64, HSE Books ISBN 0-7176-0870-0 Signpost to the Health and Safety (Safety Signs and Signals) Regulations 1996 INDG 184L HSE Books

386

17.30

Supply of Machinery (Safety) Regulations 1992

17.30.1

Introduction

The Supply of Machinery (Safety) Regulations 1992 entered into force on 1 January 1993, although there was a transitional period to 31 December 1994 during which the manufacturer or importer into the European Community was able to choose between either the Community regime described below or complying with the health and safety legislation in force on 31 December 1992. The Supply of Machinery (Safety) (Amendment) Regulations 1994 made a number of changes to the 1992 Regulations, in particular, to widen the scope to include machinery for lifting persons and safety components for machinery. The main provisions of the amending Regulations entered into force on 1 January 1995. Therefore from 1 January 1995: ➤ most machinery supplied in the UK, including imports, must: ➤ satisfy wide-ranging health and safety requirements, for example, on construction, moving parts and stability ➤ in some cases, have been subjected to typeexamination by an approved body ➤ carry CE marking and other information ➤ the manufacturer or the importer will generally have to be able to assemble a ﬁle containing technical information relating to the machine.

17.30.2

Other relevant legislation to the supply of machinery

The two sets of Regulations that will often apply are the: ➤ Electrical Equipment (Safety) Regulations 1994, which apply to most electrically powered machinery used in workplaces ➤ Electromagnetic Compatibility Regulations 1992 which cover equipment likely to cause electromagnetic disturbance, or whose performance is likely to be affected by electromagnetic disturbance. In some cases, other laws may apply such as the Simple Pressure Vessels (Safety) Regulations 1991 or the Gas Appliances (Safety) Regulations 1995. All these Regulations implement European Directives and contain various requirements. The existence of CE marking on machinery should indicate that the manufacturer has met all of the requirements that are relevant.

Summary of the main legal requirements Special transitional arrangements remain for products covered by existing Directives on roll-over and fallingobject protective structures and industrial trucks and for safety components and machinery for lifting persons. Failure to comply with these requirements: ➤ will mean that the machinery cannot legally be supplied in the UK ➤ could result in prosecution and penalties, on conviction, of a ﬁne up to £5000 or, in some cases, of imprisonment for up to three months, or of both. The same rules apply everywhere in the European Economic Area (EEA), so machinery complying with the Community regime may be supplied in any EEA State.

17.30.3

Coverage

➤ to the extent that the hazards are wholly or partly covered by other Directives, from the date those other Directives are implemented into UK law ➤ machinery ﬁrst supplied in the European Community before 1 January 1993 ➤ safety components or machinery for lifting persons ﬁrst supplied in the European Economic Area before 1 January 1995. The Regulations do not apply to safety components and machinery for lifting persons ﬁrst supplied in the European Economic Area before 1 January 1995. Such products ﬁrst supplied on or after 1 January 1995 must comply either with the Supply of Machinery (Safety) Regulations or the UK health and safety legislation in force relating to these items on 14 June 1993. All such products ﬁrst supplied after 1 January 1997 must comply with the Supply of Machinery (Safety) Regulations.

Machinery, described as: ➤ an assembly of linked parts or components, at least one of which moves, with the appropriate actuators, control and power circuits, joined together for a speciﬁc application, in particular for the processing, treatment, moving or packaging of a material ➤ an assembly of machines which, in order to achieve the same end, are arranged and controlled so that they function as an integral whole ➤ interchangeable equipment modifying the function of a machine which is supplied for the purpose of being assembled with a machine (or a series of different machines or with a tractor) by the operator himself in so far as this equipment is not a spare part or a tool. Safety components for machinery, described as: ➤ components which are supplied separately to fulﬁll a safety function when in use and the failure or malfunctioning of which endangers the safety or health of exposed persons.

17.30.4

Exceptions

The Regulations do not apply to machinery or safety components: ➤ listed in Annex A ➤ previously used in the European Community or, since 1 January 1994 the European Economic Area (e.g. secondhand) ➤ for use outside the European Economic Area which does not carry CE marking ➤ where the hazards are mainly of electrical origin (such machinery is covered by the Electrical Equipment (Safety) Regulations 19941)

17.30.5

Machinery excluded – Appendix A to the Regulations

➤ Machinery whose only power source is directly applied manual effort, unless it is a machine used for lifting or lowering loads. ➤ Machinery for medical use used in direct contact with patients. ➤ Special equipment for use in fairgrounds and/or amusement parks. ➤ Steam boilers, tanks and pressure vessels. ➤ Machinery specially designed or put into service for nuclear purposes, which, in the event of failure, may result in an emission of radioactivity. ➤ Radioactive sources forming part of a machine. ➤ Firearms. ➤ Storage tanks and pipelines for petrol, diesel fuel, highly ﬂammable liquids and dangerous substances. ➤ Means of transport, i.e. vehicles and their trailers intended solely for transporting passengers by air or on road, rail or water networks. Also, transport, which is designed for transporting goods by air, on public road or rail networks or on water. Vehicles used in the mineral extraction industry are not excluded. ➤ Sea-going vessels and mobile offshore units together with equipment on board, such as vessels or units. ➤ Cableways, including funicular railways, for the public or private transportation of people. ➤ Agriculture and forestry tractors, as deﬁned by certain European Directives. ➤ Machines specially designed and constructed for military or police purposes. ➤ Certain goods and passenger lifts. ➤ Means of transport of people using rack and pinion rail mounted vehicles. ➤ Mine winding gear.

387

Introduction to Health and Safety at Work ➤ Theatre elevators. ➤ Construction site hoists intended for lifting individuals or people and goods.

17.30.6

General requirements

Subject to the exceptions and transitional arrangements described above, the Regulations make it an offence for a ‘responsible person’ to supply machinery or a safety component unless: ➤ it satisﬁes the essential health and safety requirements ➤ the appropriate conformity assessment procedure has been carried out ➤ an EC declaration of conformity or declaration of incorporation has been issued ➤ CE marking has been properly afﬁxed (unless a declaration of incorporation has been issued) ➤ it is, in fact, safe. The Regulations also make it an offence for any supplier to supply machinery or a safety component unless it is safe.

17.30.7 Essential health and safety requirements To comply with the Regulations, machinery and safety components must satisfy the essential health and safety requirements (set out in Annex B to the Regulations), which apply to it. The requirements are wide-ranging, and take into account potential dangers to operators and other exposed persons within a ‘danger zone’. Aspects covered in Part 1 include: the materials used in the construction of the machinery; lighting; controls; stability; ﬁre; noise; vibration; radiation; emission of dust, gases, etc.; and maintenance. Part 2 has additional requirements for agri-foodstuffs machinery, portable hand-held machinery, and machinery for working wood and analogous materials. Part 3 deals with particular hazards associated with mobility, Part 4 with those associated with lifting, Part 5 those with underground working and Part 6 those with the lifting or moving of persons. The requirements also comment on instructions (including translation requirements) and marking. When applying the essential health and safety requirements, technical and economic limitations at the time of construction may be taken into account.

17.30.8

Standards

Machinery and safety components manufactured in conformity with speciﬁed, published European standards which have also been published as identically worded

388

national standards (‘transposed harmonized standards’), will be presumed to comply with the essential health and safety requirements covered by those standards. The European Committee for Standardization (CEN) is working to produce a complex of European standards at three levels in support of the Machinery Directive. The ﬁrst (A) level comprises general principles for the design of machinery. The second (B) level covers speciﬁc safety devices and ergonomic aspects. The third (C) level deals with speciﬁc classes of machinery by calling up the appropriate standards from the ﬁrst two levels and addressing requirements speciﬁc to the class.

17.30.9

Step 1 – Conformity assessment (‘attestation’)

The responsibility for demonstrating that the machinery or safety component satisﬁes the essential health and safety requirements rests on the ‘responsible person’. For most machinery or safety components (other than those listed in Annex D): the ‘responsible person’, must be able to assemble the technical ﬁle described in Annex E. For machinery or safety components listed in Annex D: the ‘responsible person’ must follow the special procedures described below.

17.30.10

Step 2 – Declaration procedure

Declaration of conformity: the ‘responsible person’ must then draw up an EC declaration of conformity, described in Annex G, for each machine or safety component supplied. This declaration is intended to be issued with the machine or safety component and declares that it complies with the relevant essential health and safety requirements or with the example that underwent type-examination. Declaration of incorporation: alternatively, where the machinery is intended for incorporation into other machinery or assembly with other machinery to constitute machinery covered by the Regulations, the ‘responsible person’ may draw up a declaration of incorporation, described in Annex H, for each machine.

17.30.11

Step 3 – Marking

Once a declaration of conformity has been issued, the ‘responsible person’ must afﬁx the CE marking to the machinery. CE markings must be afﬁxed in a distinct, visible, legible and indelible manner. The CE marking should not be afﬁxed to safety components or for machinery for which a declaration of incorporation has been issued.

Summary of the main legal requirements The Regulations make it an offence to afﬁx a mark to machinery, which may be confused with CE marking.

Enforcement

17.30.13

17.31

Control of Vibration at Work Regulations 2005

17.31.1

Introduction

These new regulations implement European Directive Vibration Directive 2002/44/EC. They came into force in July 2005 with some transitional arrangements for the exposure limits until 2010 (2014 for WBV the whole body vibration exposure limit value for agriculture and forestry sectors). The regulations impose duties on employers to protect employees who may be exposed to risk from vibration at work, and other persons who may be affected by the work.

17.31.2

Interpretation – Regulation 2

‘Daily exposure’ means the quantity of mechanical vibration to which a worker is exposed during a working day, normalized to an 8-hour reference period, which takes account of the magnitude and duration of the vibration. ‘hand-arm vibration’ (HAV) means mechanical vibration which is transmitted into the hands and arms during a work activity. ‘whole-body vibration’ (WBV) means mechanical vibration which is transmitted into the body when seated or standing through the supporting surfaces, during a work activity or as described in Regulation 5 (3) (f ).

Penalties

The maximum penalty for contravening the prohibition on supply of non-compliant machinery and safety components is imprisonment for up to three months or a ﬁne of up to £5000 or both. The penalty for other contraventions of the Regulations is a ﬁne up to the same amounts. It is for the Courts to decide the penalty in any given case, taking into account the severity of the offence. The Regulations provide a defense of due diligence. They also provide for proceedings to be taken against a person other than the principal offender, if it is the other person’s fault, and against ofﬁcers of a company or other body corporate.

17.31.3

Application – Regulation 3

For work equipment ﬁrst provided to employees for use prior to 6 July 2007 and where compliances with the exposure limit values is not possible employers have until 2010 to comply and in the case of agriculture and forestry 2014 (for whole body vibration). However action must be taken to use the latest technical advances and the organizational measures in accordance with Regulation 6 (2).

17.31.4

Exposure limit values and action values – Regulation 4

HAV

17.30.14

References

Supplying new machinery advice to suppliers, INDG270, 1998 HSE Books ISBN 0-7176-1560-X

(a) 8 hour daily exposure limit value is 5 m/s2 A (8) (b) 8 hour daily exposure action value is 2.5 m/s2 A (8) (c) daily exposure ascertained as set out in Schedule 2 Part I.

389

Control of Vibration at Work Regulations 2005

In Great Britain, the Health and Safety Executive is responsible for enforcing the Regulations in relation to machinery and safety components for use at work. Local authority Trading Standards Ofﬁcers are responsible for enforcement in relation to machinery and safety components for private use. In Northern Ireland, the Department of Economic Development and the Department of Agriculture are responsible for enforcing the Regulations in relation to machinery and safety components for use at work. District councils are responsible for enforcement in relation to machinery and safety components for private use. The enforcement authorities have available to them various powers under the Health and Safety at Work etc. Act 1974, the Health and Safety at Work (Northern Ireland) Order 1978 and the Consumer Protection Act 1987, for example, relating to suspension, prohibition and prosecution. Where machinery bearing the CE marking is safe, but there are breaches of other obligations, the ‘responsible person’ will be given the opportunity to correct the breach before further enforcement action is taken. The Machinery Directive, as amended, requires Member States to inform the European Commission of any speciﬁc enforcement action taken. The Commission will consider whether the action is justiﬁed and advise the parties concerned accordingly.

17.31

17.30.12

Buying new machinery A short guide to the law, INDG 271, 1998 HSE Books ISBN 0-7176-1559-6

Introduction to Health and Safety at Work WBV (a) 8 hour daily exposure limit value is 1.15 m/s2 A (8) (b) 8 hour daily exposure action value is 0.5 m/s2 A (8) (c) daily exposure ascertained as set out in Schedule 2 Part I.

17.31.5 Assessment of risk to health created by vibration at the workplace – Regulation 5

The employer shall record: ➤ the signiﬁcant ﬁndings of the risk assessment as soon as is practicable after the risk assessment is made or changed, and ➤ the measures which they have taken and which they intend to take to meet the requirements of Regulation 6.

17.31.6 A suitable and sufﬁcient risk assessment must be made where work liable to expose employees is carried on. The risk assessment must identify the measures which need to be taken to comply with these Regulations. Assessment of daily exposure should be by means of: ➤ observation of speciﬁc working practices ➤ reference to relevant work equipment vibration data ➤ if necessary measurement of the magnitude of vibration to which employees are exposed, and ➤ likelihood of exposure at or above an exposure action value or above an exposure limit value. The risk assessment shall include consideration of: ➤ the magnitude, type and duration of exposure, including any exposure to intermittent vibration or repeated shocks ➤ the effects of exposure to vibration on employees whose health is at particular risk from such exposure ➤ any effects of vibration on the workplace and work equipment, including the proper handling of controls, the reading of indicators, the stability of structures and the security of joints ➤ any information provided by the manufacturers of work equipment ➤ the availability of replacement equipment designed to reduce exposure to vibration ➤ any extension of exposure at the workplace to whole-body vibration beyond normal working hours, including exposure in rest facilities supervised by the employer ➤ speciﬁc working conditions such as low temperatures, and ➤ appropriate information obtained from health surveillance including, where possible, published information. The risk assessment shall be reviewed regularly and forthwith if: ➤ there is reason to suspect that the risk assessment is no longer valid, or ➤ there has been a signiﬁcant change in the work to which the assessment relates and where, as a result of the review, changes to the risk assessment are required, those changes shall be made.

390

Elimination or control of exposure to vibration at the workplace – Regulation 6

Following the general principles of prevention in the Management Regulations, the employer shall ensure that risk from the exposure of his or her employees to vibration is either eliminated at source or reduced as low as reasonably practicable. Where this is not reasonably practicable and the risk assessment indicates that an exposure action value is likely to be reached or exceeded, the employer shall reduce exposure as low as reasonably practicable by establishing and implementing a programme of organizational and technical measures which is appropriate. Consideration must be given to: ➤ other working methods which eliminate or reduce exposure to vibration ➤ a choice of work equipment of appropriate ergonomic design which, taking account of the work to be done, produces the least possible vibration ➤ the provision of auxiliary equipment which reduces the risk of injuries caused by vibration ➤ appropriate maintenance programmes for work equipment, the workplace and workplace systems ➤ the design and layout of workplaces, work stations, and rest facilities ➤ suitable and sufﬁcient information and training for employees, such that work equipment may be used correctly and safely, in order to minimize their exposure to vibration ➤ limitation of the duration and intensity of exposure to vibration ➤ appropriate work schedules with adequate rest periods, and ➤ the provision of clothing to protect employees from cold and damp. Subject to implementation dates, the employer shall: ➤ ensure that no employees are exposed to vibration above an exposure limit value; or ➤ if an exposure limit value is exceeded, the employer shall forthwith: ➤ take action to reduce exposure to vibration to below the limit value;

Summary of the main legal requirements ➤ identify the reason for that limit being exceeded; and ➤ modify the organizational and technical measures taken in accordance with paragraph (2) to prevent it being exceeded again.

The employer shall provide those employees and their representatives with suitable and sufﬁcient information, instruction and training. The information, instruction and training provided shall include:

This shall not apply where the exposure of an employee to vibration is usually below the exposure action value but varies markedly from time to time and may occasionally exceed the exposure limit value, provided that:

➤ the organizational and technical measures taken in order to comply with the requirements of Regulation 6 ➤ the exposure limit values and action values ➤ the signiﬁcant ﬁndings of the risk assessment, including any measurements taken ➤ why and how to detect and report signs of injury ➤ entitlement to appropriate health surveillance ➤ safe working practices to minimize exposure to vibration, and ➤ the collective results of any health surveillance undertaken in accordance with Regulation 7 in a form calculated to prevent those results from being identiﬁed as relating to a particular person.

➤ any exposure to vibration averaged over one week is less than the exposure limit value ➤ there is evidence to show that the risk from the actual pattern of exposure is less than the corresponding risk from constant exposure at the exposure limit value ➤ risk is reduced as low as reasonably practicable, taking into account the special circumstances, and ➤ the employees concerned are subject to increased health surveillance, where such surveillance is appropriate. Account must be taken of any employee whose health is likely to be particularly at risk from vibration.

17.31.7

Health surveillance – Regulation 7

The information, instruction and training required must be adapted to take account of signiﬁcant changes in the type of work carried out or methods of work used by the employer, and cover all persons who carry out work in connection with the employer’s duties under these Regulations.

If: ➤ the risk assessment indicates that there is a risk to the health of any employees who are, or are liable to be, exposed to vibration, or ➤ employees are exposed to vibration at or above an exposure action value the employer shall ensure that such employees are under suitable health surveillance. Records must be kept and give access to employees to their own records and provide the enforcing authorities with copies, as it may require. A range of speciﬁed action is required if problems are found with the health surveillance results.

17.31.8 Information, instruction and training – Regulation 8 If: ➤ the risk assessment indicates that there is a risk to the health of employees who are, or who are liable to be, exposed to vibration, or ➤ employees are exposed to vibration at or above an exposure action value

17.31.9

References

Hand-arm vibration: Control of Vibration at Work Regulations L140 HSE Books 2005 ISBN 0 7176 6125 3 Control the risks from hand-arm vibration Advice for employers on the Control of Vibration at Work Regulations INDG175 (rev2) HSE Books 2005 ISBN 0 7176 6117 2 Vibration Solutions Practical way to reduce the risk of hand-arm vibration, HSG170, HSE Books 1997 ISBN 0-7176-0954-5 Hand-arm vibration Advice for employees Pocket card INDG296 (rev1) 2005 HSE Books ISBN 0-7176-6118-0 Control back-pain risks from whole-body vibration Advice for employers on the Control of Vibration at Work Regulations 2005 INDG242 (rev1) 2005 HSE Books ISBN 0-7176-6119-9 Drive away bad backs Advice for mobile machine operators and drivers. INDG404 2005 HSE Books ISBN 0-7176-6120-2 Power tools, How to reduce vibration health risks INDG338 2001 HSE Books ISBN 0-7176-2008-5

391

17.32

Workplace (Health, Safety and Welfare) Regulations 1992 as amended in 2002

Introduction to Health and Safety at Work 17.32

Workplace (Health, Safety and Welfare) Regulations 1992 as amended in 2002

17.32.1

General

These regulations were made to implement the European Directive on the minimum safety and health requirements for the workplace. A workplace for these purposes is deﬁned very widely to include any part of non-domestic premises to which people have access while at work and any room, lobby, corridor, staircase or other means of access to or exit from them. The main exceptions to these rules are constructions sites, means of transport, mines and quarries and other mineral extraction sites. Employers have a duty to ensure that workplaces under their control comply with the requirements of these regulations. Any workplace and relevant equipment, devices and systems must be properly maintained. A maintenance system must be set up where appropriate, i.e. where a fault could result in a failure to comply and/or mechanical ventilation systems provided under Regulation 6. The main requirements are summarized below. They are expressed in very general terms, and in each case it will be necessary to turn to the Approved Code or Practice associated with these Regulations for clariﬁcation of what is necessary to meet the objectives set.

Emergency lighting Emergency lighting shall be provided where persons are especially exposed to danger if artiﬁcial light fails. Lights should avoid glare and dazzle and should not themselves cause a hazard. They should not be obscured and be properly maintained.

Workplaces, furniture and fittings Workplaces furniture and ﬁttings should be kept sufﬁciently clean. Surfaces inside buildings shall be capable of being kept sufﬁciently clean.

Floors Floors should not be slippery and wall surfaces should not increase ﬁre risks.

Wastes Wastes should not be allowed to accumulate, except in suitable receptacles and should be kept free from offensive waste products and discharges.

Room dimensions Room dimensions have to allow adequate unoccupied space to work in and to move freely. 11 m3 minimum per person is required, excluding anything over 3 m high and furniture, etc.

Workstations 17.32.2 Health – The Working Environment Regulations 6, 7, 8, 9 and 10

Workstations shall be suitable for any person in the workplace who is likely to work at that workstation and for any work that is likely to be done there.

Ventilation Ventilation must be effective in enclosed areas, and any plant used for this purpose must incorporate warning devices to signal breakdowns which might endanger health or safety.

Outside workstations Outside workstations shall provide, so far as is reasonably practicable, protection from adverse weather; adequate means of escape in emergencies; and ensure that no person is likely to slip or fall.

A reasonable temperature A reasonable temperature must be maintained during working hours and sufﬁcient thermometers must be provided to enable people at work to determine the temperature in any workroom. The temperature should be comfortable without the need for special clothing. Special guidance is available for areas like food processing where it could be very hot or very cold. Temperature should be at least 16ºC, or where strenuous effort is involved 13ºC.

Lighting Lighting must be suitable and sufﬁcient. This should be natural lighting so far as is reasonably practicable.

392

Seating Seating shall be provided where work can or must be done sitting and shall be suitable for the person as well as the work. A footrest shall be provided where necessary.

17.32.3

Safety – Accident Prevention Regulations 5, 12, 13, 14, 15, 16, 17, 18 and 19

Maintenance The workplace and equipment, devices and systems shall be maintained (including cleaned as appropriate) in an efﬁcient state, efﬁcient working order and in good repair, and where appropriate subject to a system

Summary of the main legal requirements of maintenance. This generally means planned rather than breakdown maintenance. Systems include ventilation, emergency lighting, safety fences, window cleaning devices, moving walkways are all given as examples.

Floors and traffic routes Floors and the surface of trafﬁc routes shall be suitably constructed for their intended purpose and free of slope and holes (unless fenced). They should not be uneven or slippery. The trafﬁc routes should be of adequate width and height to allow people and vehicles to circulate safely with ease and they should be kept free of obstructions. Additional precautions are necessary where pedestrians have to cross or share vehicle routes. Open sides of staircases should be fenced with an upper rail 900 mm or higher and a lower rail. Loading bays should have exits or refuges to avoid people getting crushed by vehicles.

Falls and falling objects

and people at doors, gateways and common routes. Workplaces should have protection from vehicles.

Doors and gates Doors, gates and moving walkways have to be of sound construction and ﬁtted with appropriate safety devices.

17.32.4

Welfare – provision of facilities – Regulations 20, 21, 22, 23, 24 and 25

Sanitary conveniences and washing facilities Suitable and sufﬁcient sanitary conveniences and washing facilities should be provided at readily accessible places. The facilities must be kept clean, adequately ventilated and lit. Washing facilities should have running hot and cold or warm water, soap and clean towels or other method of cleaning or drying. If necessary, showers should be provided. Men and women should have separate facilities unless each facility is in a separate room with a lockable door and is for use by only one person at a time.

Now covered By Work at Height Regulations 2005.

Drinking water Tanks, pits Where there is a risk of falling into a tank, pit or structure containing a dangerous substance that is likely to: ➤ ➤ ➤ ➤

scald or burn be poisonous or corrosive have an asphyxiating gas fume or vapour have any granular or free ﬂowing substance likely to cause harm

measures must be taken to securely fence or cover the tank, pit or structure.

An adequate supply of wholesome drinking water, with an upward drinking jet or suitable cups, should be provided. Water should only be supplied in reﬁllable enclosed containers where it cannot be obtained directly from a mains supply.

Accommodation for clothing and facilities for changing Adequate, suitable and secure space should be provided to store workers’ own clothing and special clothing. The facilities should allow for drying clothing. Changing facilities should also be provided for workers who change into special work clothing.

Ladders and roofs Now covered By Work at Height Regulations 2005.

Glazing Windows and transparent doors and partitions must be appropriately marked and protected against breakage.

Facilities to rest and to eat meals Suitable and sufﬁcient, readily accessible, rest facilities should be provided. Arrangements should include suitable facilities to eat meals; adequate seats with backrests and tables; means of heating food (unless hot food is available nearby) and making hot drinks.

Windows Windows and skylights must open and close safely, and be arranged so that people may not fall out of them. They must be capable of being cleaned safely.

Canteens or restaurants

Traffic routes

Suitable rest facilities

Pedestrians and vehicles must be able to circulate safely. Separation should be provided between vehicle

Suitable rest facilities should be provided for pregnant women and nursing mothers. They should be near

Canteens and restaurants may be used as rest facilities provided there is no obligation to purchase food.

393

Introduction to Health and Safety at Work sanitary facilities and where necessary, include the facility to lie down.

Non-smokers Non-smokers should be protected from discomfort caused by tobacco smoke in rest areas and rest rooms.

17.33

Work at Height Regulations 2005

17.32.5

References

The Workplace (Health, Safety and Welfare) Regulations 1992 ISBN 0-11-025804-5 Workplace Health, Safety and Welfare. Workplace (Health, Safety and Welfare) Regulations 1992 Approved Code of Practice and Guidance. L24, 1992 HSE Books ISBN 0-7176-0413-6 Workplace health, safety and welfare A short guide, INDG244, 1997 HSE Books ISBN 0-7176-1328-3

17.33

Work at Height Regulations 2005

17.33.1

Introduction

These Regulations bring together all current requirements on work at height into one goal based set of Regulations. They implement the requirements of the 2nd Amending Directive (2001/45/EC) to the Use of Work Equipment Directive (89/955/EEC) which sets out requirements for work at height. The 2nd Amending Directive as become known as the Temporary Work at Height Directive. The Regulations require a risk assessment for all work conducted at height and arrangements to be put in place for: ➤ eliminating or minimizing risks from working at height ➤ safe systems of work for organizing and performing work at height ➤ safe systems for selecting suitable work equipment to perform work at height ➤ safe systems for protecting people from the consequences of work at height.

17.33.2

Definitions – Regulation 2

‘Work at height’ means: (a) work in any place, including a place at or below ground level (b) obtaining access to or egress from such place while at work except by a staircase in a permanent workplace

394

where, if measures required by these Regulations were not taken, a person could fall a distance liable to cause personal injury. ‘Working platform’ means: (a) means any platform used as a place of work or as a means of access to or egress from a place of work (b) includes any scaffold, suspended scaffold, cradle, mobile platform, trestle, gangway, gantry and stairway which is so used.

17.33.3

Organization, planning and competence – Regulations 4 and 5

Work at height must be properly planned, appropriately supervised and carried out in a manner which is, so far as is reasonably practicable, safe. The selection of appropriate work equipment is included in the planning. Work must not be carried out if the weather conditions would jeopardize safety or health (this does not apply where members of the police, ﬁre, ambulance or other emergency services are acting in an emergency). All people involved in work at height activity including planning, organizing and supervising must be competent for such work, or if being trained, under competent supervision.

17.33.4

Avoidance of Risk – Regulation 6

A risk assessment carried out under the Management Regulations must be taken into account when identifying the measures required by these regulations. Work at height should be avoided if there are reasonably practicable alternatives. Where work at height is carried out employers must take suitable and sufﬁcient measures to prevent persons falling a distance liable to cause personal injury. The measures include: (a) ensuring work is carried out: i from an existing workplace ii using existing means of access and egress that comply with schedule 1 of the Regulations (assuming it is safe and ergonomic to do so) (b) where this is not reasonably practicable, providing work equipment (sfarp) for preventing a fall occurring. Employers must take steps to minimize the distance and the consequences of a fall, if it is not prevented. Where the distance cannot be minimized (sfarp) the consequence of a fall must be minimized and additional training, instruction and other additional suitable and sufﬁcient measures must be adopted to prevent a person falling a distance liable to cause personal injury.

Summary of the main legal requirements Work at height flow chart Assess the risks to help decide how to work safely

Is there a risk of a person falling a distance liable to cause personal injury? Yes

No Perform the task in a safe manner

Is it reasonably paracticable to safely carry out the work other than at height? Yes No Perform the task in a safe manner from the ground

Take suitable and sufficient steps PREVENT the risk of a fall, including: Using an existing work place in compliance with Schedule 1; and in other cases Minimizing the distance and consequence of a fall Selecting the most suitable work equipment in accordance with Regulation 7. Where the risk of a person or object falling still remains take suitable and sufficient measures to: MINIMIZE the consequences of any fall and provide additional training and instruction. Stemps should include the selection of work equipment in accordance with Regulations 7 and 8 When selecting work equipment give collective protection priority over personal protection.

Figure 17.8

17.33.5 General principles for selection of work equipment – Regulation 7 Collective protection measures must have priority over personal protection measures. Employers must take account of: ➤ working conditions and the risks to the safety of persons at the place where the work equipment is to be used ➤ the distance to be negotiated for access and egress ➤ distance and consequences of a potential fall ➤ duration and frequency of use ➤ need for evacuation and rescue in an emergency ➤ additional risks of using, installing and removing the work equipment used or evacuation and rescue from it ➤ other provisions of the Regulations.

Work equipment must be: ➤ appropriate for the nature of the work and the foreseeable loadings ➤ allow passage without risk ➤ be the most suitable work equipment having regard in particular to Regulation 6.

17.33.6

Requirements for particular work equipment – Regulation 8

Regulation 8 requires that various pieces of work equipment comply with the schedules to the regulations as follows: (a) a guard-rail, toe-board, barrier or similar means of protection, schedule 2 – in summary: ➤ they must be suitable, of sufﬁcient dimensions, of sufﬁcient strength and rigidity

395

Introduction to Health and Safety at Work ➤ be so placed, secured and used to prevent accidental displacement ➤ prevent fall of persons and materials ➤ supporting structure to be of sufﬁcient strength and suitable for the purpose ➤ no lateral opening save at point of access to a ladder or stairway where an opening is necessary, and: ➤ must be in place except for a time to gain access perform a particular task and then replaced ➤ compensatory safety measures must be provided if protection removed temporarily. (b) a working platform, Schedule 3 Part 1 and, in addition, where scaffolding is provided, Schedule 3 Part 2. In summary: Part 1: Supporting structure must: ➤ be suitable, of sufﬁcient strength and rigidity ➤ if wheeled prevented, by appropriate device, from moving during work ➤ must not slip and have secure attachment ➤ be stable while being erected, used modiﬁed or dismantled. Working platform to be: ➤ suitable and strong enough ➤ no accidental displacement of components ➤ remain stable during dismantling ➤ dismantled so as to prevent accidental displacement ➤ be of sufﬁcient dimensions for safe passage and use ➤ have a suitable surface and be constructed to prevent people falling through ➤ have a suitable surface and be constructed to prevent material or objects falling through unless measures have been taken to protect other persons from falling objects ➤ be erected, used and maintained so that risk of slipping and tripping is prevented and no person can be caught between working platform and adjacent structure ➤ not loaded so as too give risk of collapse or deformation. Part 2 additional for scaffolds: ➤ Strength and stability calculations required unless they are available already or scaffold is assembled in conformity with a generally recognized standard conﬁguration ➤ An assembly, use and dismantling plan must be drawn up. Could be standard plan with supplements ➤ Copy of the plan and instructions to be available for persons doing the work ➤ Dimensions, form and layout to be suitable

396

(c)

(d) (e)

(f) (g)

➤ When not available for use to be marked with warning signs and physical barrier preventing access ➤ Must be assembled, dismantled or signiﬁcantly altered under supervision of competent person a net, airbag or other collective safeguard for arresting falls which is not part of a personal fall protection system, Schedule 4 any personal fall protection system, Part 1 of Schedule 5, and ➤ A work positioning system, Part 2 of Schedule 5 ➤ Rope access and positioning techniques, Part 3 of Schedule 5 ➤ A fall arrest system, Part 4 of Schedule 5 ➤ A work restraint system, Part 5 of Schedule 5, and A ladder, Schedule 6 in summary ➤ only to be used for work at height if the risk assessment demonstrates that the use of more suitable equipment is not justiﬁed because of the low risk and the short duration of use or existing features on site that cannot be altered ➤ surface on which ladder rests must be stable, ﬁrm, of sufﬁcient strength and suitable composition so its rungs remain horizontal ➤ must be positioned to ensure stability ➤ suspended ladder attached ﬁrmly without swing (except ﬂexible ladder) ➤ portable ladder to be prevented from slipping by securing the stiles near their upper and lower ends and using an anti-slip device or by any other equivalent measures ➤ when used for access must protrude above place of landing unless other ﬁrm handholds provided ➤ interlocking or extension pieces must not move, relative to each other, during use ➤ mobile ladder to be prevented from moving before being stepped on ➤ sufﬁcient safe landings provided for vertical distances of 9 metres or more above base ➤ must be used so that a secure foothold and handhold always available ➤ must be used so that user can maintain a secure handhold while carrying a load (exceptions for using stepladders for low risk, short duration work).

17.33.7

Fragile Surfaces – Regulation 9

Employers must take steps to prevent people falling through any fragile surface. Steps to be taken include: ➤ avoid, so far as is reasonably practicable, passing across or near, or working on or near, a fragile surface

Summary of the main legal requirements ➤ where this is not reasonably practicable: ➤ provide suitable and sufﬁcient platforms, covering, guard-rails or other similar means of support or protection and use them ➤ provide suitable and sufﬁcient guard-rails to prevent persons falling through fragile surfaces ➤ where a risk of falling remains take suitable and sufﬁcient measures to minimize the distances and consequences of a fall ➤ provide prominent warning signs at approach to the fragile surface, or make people aware of the fragile surface if not reasonably practicable ➤ where the risk of falling remains despite the precautions a suitable and sufﬁcient fall arrest system must be provided.

17.33.8 Falling Objects and danger areas – Regulations 10 and 11

suitable intervals and each time that exceptional circumstances which are liable to jeopardize the safety of the work equipment have occurred, for example a severe storm ➤ in addition, a working platform used for construction and from which a person could fall more than 2 metres has to be inspected in that position (mobile equipment on the site) before use and within the last 7 days. The particulars for this inspection are set out in Schedule 7 ➤ no work equipment (Lifting equipment is covered under LOLER) may either leave the undertaking or be obtained from another undertaking without evidence of in-date inspection ➤ results of inspections must be recorded and retained until the next due inspection is recorded. Reports must be provided within 24 hours and kept at the site until construction work is complete and thereafter at the ofﬁce for 3 months.

Suitable and sufﬁcient steps must be taken to:

17.33.10 ➤ prevent the fall of any material or object ➤ if not reasonably practicable to prevent the fall of any material or object, prevent persons being struck by falling objects or material (if liable to cause personal injury) by for example providing covered walkways or fan scaffolds ➤ prevent material or objects being thrown or tipped from height where it is likely to cause injury ➤ store materials and objects in such a way as to prevent risk to any person arising from the collapse, overturning or unintended movement ➤ where danger of being struck exists unauthorized persons must be kept out of the area by suitable devices and the area clearly indicated ➤ store materials and objects so as to prevent them collapsing, overturning or move in a way that could be a risk to people.

The surface and every parapet, permanent rail or other such fall protection measure of every place of work at height must be checked on each occasion before the place is used.

17.33.11

This regulation applies only to work equipment to which Regulation 8 and Schedules 2 to 6 apply. The requirements include the following: ➤ where work equipment used for work at height depends for safety on how it is installed or assembled, the employer must ensure that it is not used after installation or assembly in any position unless it has been inspected in that place ➤ where work equipment is exposed to conditions causing deterioration which is liable to result in dangerous situations, it must also be inspected at

Duties of persons at work – Regulation 12

Every person must, where working under the control of another person, report to that person any activity or defect relating to work at height which they know is likely to endanger themselves or others. Work equipment must be used in accordance with training and instructions.

17.33.12 17.33.9 Inspection of Work Equipment – Regulation 12

Inspection of places of work at height – Regulation 13

References

Work at Height Regulations 2005, SI 2005/735, The Stationery Ofﬁce The Work at Height Regulations 2005:A brief guide, INDG401, 2005 HSE Books ISBN 0 7176 2976 7 A head for heights Guidance for working at height in construction. Video 2003 HSE Books ISBN 0-7176-2862-0 Safe use of ladders and stepladders. An employers’ guide INDG402 2005 HSE Books ISBN 0-7176-6105-9 Height safe Essential health and safety information for people who work at height. HSE’s website; www.hse. gov.uk

397

17.34

Other relevant regulations in brief

Introduction to Health and Safety at Work High Designs Design of safe access and places for work at height during maintenance operations 1988 HSE Books ISBN 0-7176-1925-7 General access scaffolds and ladders CIS49 1997 HSE Books Working on Roofs INDG 284 1999 HSE Books Health and Safety in Roof Work HSG 33 1998 HSE Books ISBN 0-7176-1425-5

17.34

Other relevant regulations in brief

There are a number of other Regulations which do not form part of the NEBOSH General Certiﬁcate syllabus. Nevertheless, they are important to a wider understanding of health and safety legislation. Very brief summaries are covered here.

17.34.1

Control of Asbestos Regulations 2006

The Control of Asbestos Regulations 2006 came into force on 13 November 2006 (Asbestos Regulations – SI 2006/2739). These Regulations bring together the three previous sets of Regulations covering the prohibition of asbestos, the control of asbestos at work and asbestos licensing. The Regulations prohibit the importation, supply and use of all forms of asbestos. They continue the ban introduced for blue and brown asbestos 1985 and for white asbestos in 1999. They also continue the ban the secondhand use of asbestos products such as asbestos cement sheets and asbestos boards and tiles; including panels which have been covered with paint or textured plaster containing asbestos. The ban applies to new use of asbestos. If existing asbestos containing materials are in good condition, they may be left in place, their condition monitored and managed to ensure they are not disturbed. The Asbestos Regulations also include the ‘duty to manage asbestos’ in non-domestic premises. Guidance on the duty to manage asbestos can be found in the ‘Approved Code of Practice The Management of Asbestos in Non-Domestic Premises’, L127, ISBN 0 7176 6209 8 and on the duty to manage area of this website. The Regulations require mandatory training for anyone liable to be exposed to asbestos ﬁbres at work (see Regulation 10). This includes maintenance workers and others who may come into contact with or who may disturb asbestos (e.g. cable installers) as well as those involved in asbestos removal work. When work with asbestos or which may disturb asbestos is being carried out, the Asbestos Regulations

398

require employers and the self-employed to prevent exposure to asbestos ﬁbres. Where this is not reasonably practicable, they must make sure that exposure is kept as low as reasonably practicable by measures other than the use of respiratory protective equipment. The spread of asbestos must be prevented. The Regulations specify the work methods and controls that should be used to prevent exposure and spread. Worker exposure must be below the airborne exposure limit (Control Limit). The Asbestos Regulations have a single Control Limit for all types of asbestos of 0.1 ﬁbres per cm3. A Control Limit is a maximum concentration of asbestos ﬁbres in the air (averaged over any continuous 4 hour period) that must not be exceeded. In addition, short term exposures must be strictly controlled and worker exposure should not exceed 0.6 ﬁbres per cm3 of air averaged over any continuous 10 minute period using respiratory protective equipment if exposure cannot be reduced sufﬁciently using other means. Respiratory protective equipment is an important part of the control regime but it must not be the sole measure used to reduce exposure and should only be used to supplement other measures. Work methods that control the release of ﬁbres such as those detailed in the Asbestos Essentials Task Sheet (http://www.hse.gov.uk/ asbestos/essentials/index.htm) for non-licensed work should be used. Respiratory protective equipment must be suitable, must ﬁt properly and must ensure that worker exposure is reduced as low as is reasonably practicable. Most asbestos removal work must be undertaken by a licensed contractor but any decision on whether particular work is licensable is based on the risk. Work is only exempt from licensing if: ➤ the exposure of employees to asbestos ﬁbres is sporadic and of low intensity (but exposure cannot be considered to be sporadic and of low intensity if the concentration of asbestos in the air is liable to exceed 0.6 ﬁbres per cm3 measured over 10 minutes), and ➤ it is clear from the risk assessment that the exposure of any employee to asbestos will not exceed the control limit, and ➤ the work involves: ➤ short, non-continuous maintenance activities. Work can only be considered as short, noncontinuous maintenance activities if any one person carries out work with these materials for less than one hour in a seven-day period. The total time spent by all workers on the work should not exceed a total of two hours ➤ removal of materials in which the asbestos ﬁbres are ﬁrmly linked in a matrix, Such materials include: asbestos cement; textured

Summary of the main legal requirements decorative coatings and paints which contain asbestos; articles of bitumen, plastic, resin or rubber which contain asbestos where their thermal or acoustic properties are incidental to their main purpose (e.g. vinyl ﬂoor tiles, electric cables, rooﬁng felt) and other insulation products which may be used at high temperatures but have no insulation purposes, for example gaskets, washers, ropes and seals ➤ encapsulation or sealing of asbestos-containing materials which are in good condition, or ➤ air monitoring and control, and the collection and analysis of samples to ﬁnd out if a speciﬁc material contains asbestos. Under the Asbestos Regulations, anyone carrying out work on asbestos insulation, asbestos coating or asbestos insulating board (AIB) needs a licence issued by HSE unless they meet one of the exemptions above. Although a licence may not be needed to carry out a particular job, there is still a need to comply with the rest of the requirements of the Asbestos Regulations. If the work is licensable there are a number of additional duties, to: ➤ notify the enforcing authority responsible for the site where the work is being done (for example, HSE or the local authority) ➤ designate the work area (see Regulation 18 for details) ➤ prepare speciﬁc asbestos emergency procedures; and ➤ pay for employees to undergo medical surveillance. The Asbestos Regulations require any analysis of the concentration of asbestos in the air to be measured in accordance with the 1997 WHO recommended method. From 6 April 2007, a clearance certiﬁcate for re-occupation may only be issued by a body accredited to do so. At the moment, such accreditation can only be provided by the United Kingdom Accreditation Service (http://www.ukas.com/). More details of how to undertake work with asbestos containing materials, the type of controls necessary, what training is required and analytical methods can be found in the following HSE publications ➤ Approved Code of Practice Work with Materials containing Asbestos, (http://www.hse.gov.uk/pubns/ books/l143.htm) L143, ISBN 0 7176 6206 3 ➤ Asbestos: the Licensed Contractors Guide, HSG 247, ISBN 0 7176 2874 4 ➤ Asbestos: The analysts’ guide for sampling, analysis and clearance procedures, HSG 248, ISBN 0 7176 2875 2

➤ Asbestos Essentials, HSG 210, ISBN 0 7176 1887 0 (Asbestos Essentials task sheets are available on the Asbestos Essentials area of this website).

17.34.2

Disability Discrimination Act 1995 and 2005

The Disability Discrimination Act 1995 (DDA 1995) The Disability Discrimination Act (DDA) 1995 aims to end the discrimination that many disabled people face. This Act gives disabled people rights in the areas of: ➤ ➤ ➤ ➤

employment education access to goods, facilities and services buying or renting land or property.

The Act also allows the government to set minimum standards so that disabled people can use public transport easily. From 1 October 2004, Part 3 of the DDA 1995 has required businesses and other organizations to take reasonable steps to tackle physical features that act as a barrier to disabled people who want to access their services. This may mean to remove, alter or provide a reasonable means of avoiding physical features of a building which make access impossible or unreasonably difﬁcult for disabled people. Examples include: ➤ putting in a ramp to replace steps ➤ providing larger, well deﬁned signs for people with a visual impairment ➤ improving access to toilet or washing facilities. Businesses and organizations are called ‘service provider’ and include shops, restaurants, leisure centres and places of worship.

The Disability Discrimination Act 2005 (DDA 2005) In April 2005 a new Disability Discrimination Act was passed, which amends or extends existing provisions in the DDA 1995, including: ➤ making it unlawful for operators of transport vehicles to discriminate against disabled people ➤ making it easier for disabled people to rent property and for tenants to make disability-related adaptations ➤ making sure that private clubs with 25 or more members cannot keep disabled people out, just because they have a disability ➤ extending protection to cover people who have HIV, cancer and multiple sclerosis from the moment they are diagnosed

399

Introduction to Health and Safety at Work ➤ ensuring that discrimination law covers all the activities of the public sector ➤ requiring public bodies to promote equality of opportunity for disabled people. Others changes will come into force in December 2006 – the Disability Rights Commission (DRC) website has more details on these.

17.34.3

Electrical (Safety) Regulations 1994

These Regulations came into force in January 1995 and relate to the supply of electrical equipment with a working voltage between 50 and 1000 volts and are made under the Consumer Protection Act 1987. They apply to suppliers, which include both landlords and letting agents. The Regulations apply to all mains voltage household electrical goods and require them to be safe so that there is no risk of injury or death to humans or pets, or risk of damage to property. They do not apply to ﬁxed electrical wiring and built-in appliances like central heating systems. The Regulations also require that instructions be provided where safety depends on the user being aware of certain issues and equipment should be labelled with the CE marking. There are other electrical consumer regulations, like The Plugs and Sockets Regulations 1994 and the Low Voltage Electrical Equipment Regulations 1989.

17.34.4

Gas appliances (Safety) Regulations 1992

The Gas Appliance Regulation cover the safety standards on new gas appliances which have to: ➤ satisfy safety and efﬁciency standards ➤ undergo type examination and supervision during manufacture ➤ carry the CE mark and speciﬁed information ➤ be accompanied by instructions and warnings in the language of destination.

17.34.5 Gas Safety (Installation and Use) Regulations 1998 The Installation and Use Regulations place duties on gas consumers, installers, suppliers and landlords to ensure that: ➤ only competent people work on gas installations (Registered with CORGI the Council for Registered Gas Installers) ➤ no one is permitted to use suspect gas appliances ➤ landlords are responsible, in certain cases, to make sure that ﬁttings and ﬂues are maintained

400

➤ with the exception of room sealed appliances there are restrictions on gas appliances in sleeping accommodation ➤ instantaneous gas water heaters must be room sealed or ﬁtted with appropriate safety devices.

17.34.6

Control of Lead at Work Regulations 2002

These Regulations came into force in November 2002 and impose requirements for the protection of employees who might be exposed to lead at work and others who might be affected by the work. The regulations: ➤ require occupational exposure levels for lead and lead alkyls ➤ require blood-lead action and suspension levels for women of reproductive capacity and others ➤ re-impose a prohibition for women of reproductive capacity and young persons in speciﬁed activities ➤ require an employer to carry out a risk assessment ➤ require employers to restrict areas where exposures are likely to be signiﬁcant if there is a failure of controls measures ➤ impose requirements for the examination and testing of engineering controls and RPE and the keeping of PPE ➤ impose new sampling procedures for air monitoring ➤ impose requirements in relation to medical surveillance ➤ require information to be given to employees ➤ the keeping of records and identiﬁcation of containers and pipes.

17.34.7

Occupiers Liability Acts 1957 and 1984 – Civil Law

The 1957 Act concerns the duty that the occupier of premises has towards visitors in relation to the condition of the premises and to things which have or have not been done to them. The Act imposes: ➤ a duty to take reasonable care to see that a visitor is reasonably safe in using the premises for the purpose for which they were invited or permitted by the occupier to be there ➤ the common duty of care will differ depending on the visitor, so a greater duty is owed to children ➤ an occupier can expect that a person in the exercise of their trade or profession will appreciate and guard against normal risks, for example, a window cleaner ➤ no duty of care is owed to some one exercising a public right of way. The 1984 Act extends the duty of care to persons other than visitors, i.e. trespassers. The occupier has to take

Summary of the main legal requirements reasonable care in all the circumstances to see that nonvisitors do not get hurt on the premises because of its condition or the things done or not done to it. The occupier must cover perceived dangers and must have reasonable grounds to know that the trespassers may be in the vicinity.

17.34.8

Control of Pesticides Regulations 1986

These Regulations made under the Food and Environment Protection Act 1985 all came into force by 1 January 1988. The Regulations apply to any pesticide or any substance used generally for plant control and protection against pests of all types, including antifouling paint used on boats. They do not apply to substances covered by other Acts like the Medicines Act 1968, The Food Safety Act 1990, those used in laboratories and a number of other speciﬁc applications. No person may advertise, sell, supply, store, use a pesticide unless it has received ministerial approval and the conditions of the approval have been complied with. The approval may be experimental, provisional or full, and the Minister has powers to impose conditions. The Regulations also cover the need for users to be competent and have received adequate information and training. Certiﬁcates of competence (or working under the supervision of a person with a certiﬁcate) are required where pesticides, approved for agricultural use are used commercially.

17.34.9 Pressure Systems Safety Regulations 2000 (PSSR) These Regulations came into effect in February 2000 and replace the Pressure Systems and Transportable Gas Containers Regulations 1989. Transportable gas containers are covered by the Use of Transportable Pressure Receptacles Regulations 1996 (SI 1996 No 2092). The aim of PSSR is to prevent serious injury from the hazard associated with stored energy as a result

of a pressure system or one of its parts failing. The Regulations cover: ➤ steam at any pressure ➤ gases which exert a pressure in excess of 0.5 bar above atmospheric pressure ➤ ﬂuids which may be mixtures of liquids, gases and vapours where the gas or vapour phase may exert a pressure in excess of 0.5 bar above atmospheric pressure. With the exception of scalding from steam, the Regulations do not consider the effects of the hazardous contents being released following failure. The stored contents are of concern where they can accelerate wear and cause more rapid deterioration and an increased risk of failure.

17.34.10

Working Time Regulations 1998 as amended by 1999 Regulations

These Regulations came into force in October 1998 and, for speciﬁed workers, restrict the working week to 48 hours per 7-day period. Individuals can voluntarily agree to dis-apply the weekly working hours limit. Employers must keep a copy of all such individual agreements. Workers whose working time is not measured or predetermined, or who can themselves determine the duration of their working day are excepted from weekly working time, night work, rest periods and breaks. The Regulations also cover: ➤ night workers average normal daily hours limited to eight ➤ health assessment for night workers ➤ minimum daily and weekly rest periods ➤ rest breaks at work ➤ paid annual leave.

401

18

International aspects of health and safety

18.1 Introduction In 2004, an International General Certiﬁcate was introduced by NEBOSH following requests from countries around the world and international companies with crossborder operations. The main difference between the National General Certiﬁcate and the International Certiﬁcate syllabuses is the exclusion of all UK legal issues and requirements and the inclusion of three occupational health and safety management systems which are used around the world. NEBOSH expects that local occupational health and safety legal requirements and enforcement procedures will be covered during International General Certiﬁcate courses. In some parts of the world these requirements and procedures may well be based on UK law. There has also been a signiﬁcant change in reference material in that ILO Conventions, Recommendations and Codes of Practice have been included. This change is particularly signiﬁcant for Unit 9 – Work Equipment hazards and Control. There have been several other minor changes in the International General Certiﬁcate, the majority of which affect Unit 1 although there are some small changes to other units. Minor changes are discussed in Section 18.8 of this chapter. The largest change concerns the comparison of the three major occupational health and safety management systems and this comparison covers most of this chapter. The ILO estimate that two million women and men die each year as a result of occupational accidents and work related diseases. Table 18.1 shows the global numbers in more detail. In the USA in 2002, approximately two million workers were victims of workplace violence. In the UK 1.7% of working adults (357 000 workers) were the victim of one or more incidents of workplace violence.

402

Figure 18.1

Good scaffold – Leaning tower, Pisa, Italy.

Ten per cent of all skin cancers are estimated to be attributable to workplace exposure to hazardous substances. Thirty seven per cent of miners in Latin America have silicosis, rising to 50% among miners over ﬁfty. In India 54.6% of slate pencil workers and 36.2% of stone cutters have silicosis.

International aspects of health and safety Table 18.1 Numbers of Global Work-Related adverse events Event

Average daily

Work-related death

Annually

5000

2 000 000

60

22 000

Work-related accidents

740 000

270 000 000

Work-related disease

438 000

160 000 000

1205

440 000

274

100 000

Work-related deaths to children

Hazardous substance deaths Asbestos related deaths

Figure 18.3 Poor standard of scaffold not to EU standards in Poland.

Figure 18.2

Local authority building site, Turkey.

In the course of the 20th century, industrialized countries saw a clear decrease in serious injuries, not least because of real advances in making the workplace healthier and safer. The challenge is to extend the beneﬁts of this experience to the whole working world. However, 1984 saw the worst chemical disaster ever when 2500 people were killed and over 200 000 injured in the space of a few hours at Bhopal. Not only were the workers affected but their families, their neighbours and whole communities. Twenty years later many people are still affected by the disaster and are dying as a result. The rusting remains of a once magniﬁcent plant remain as a reminder of the disaster. Experience has shown that a strong safety culture is beneﬁcial for workers, employers and governments alike. Various prevention techniques have proved themselves effective, both in avoiding workplace accidents and illnesses and improving business performance. Today’s high standards in some countries are a direct result of long-term policies encouraging tripartite social dialogue,

Figure 18.4

Moving coal, Berlin waterway.

collective bargaining between trade unions and employers, and effective health and safety legislation backed by potent labour inspection. The ILO believe that Safety Management Systems like ILO-OSH 2001 provide a powerful tool for developing a sustainable safety and health culture at the enterprise level and mechanisms for the continual improvement of the working environment.

403

Introduction to Health and Safety at Work The size of the health and safety ‘problem’ in terms of numbers of work-related fatalities and injuries and incidence of ill-health will vary from country to country. However, these ﬁgures should be available from the statistics branch of the national regulator as they are available in the United Kingdom from the annual report on health and safety statistics from the HSC.

18.2 The role and function of the International Labour Organization (ILO) The International Labour Organization (ILO) is a specialized agency of the United Nations that seeks to promote social justice through establishing and safeguarding internationally recognized human and labour rights. It was founded in 1919 by the Treaty of Versailles at the end of the First World War. The motivation behind the creation of such an organization was primarily humanitarian. Working conditions at the time were becoming unacceptable to a civilized society. Long hours, unsafe, unhygienic and dangerous conditions were common in low paid manufacturing careers. Indeed, in the wake of the Russian Revolution, there was concern that such working conditions could lead to social unrest and even other revolutions. The ILO was created as a tripartite organization with governments, employers and workers represented on its governing organs. The ILO formulates international labour standards and attempts to establish minimum rights including freedom of association, the right to organize, collective bargaining, abolition of forced labour, equality of opportunity and treatment and other standards that regulate conditions across all work related activities. Representatives of all ILO member States meet annually in Geneva for the International Labour Conference that acts as a forum where social and labour questions of importance to the entire world are discussed. At this conference, labour standards are adopted and decisions made on policy and future programmes of work. The ILO has 178 member States but if a country is not a member, the ILO still has inﬂuence as a source of guidance when social problems occur. The main principles on which the ILO is based are: 1. 2. 3. 4.

labour is not a commodity freedom of expression and of association are essential to sustained progress poverty anywhere constitutes a danger to prosperity everywhere the war against want requires to be carried on with unrelenting vigour within each nation, and by

404

continuous and concerted international effort in which the representatives of workers and employers, enjoying equal status with those of governments, join with them in free discussion and democratic decision with a view to the promotion of the common welfare. A recent campaign launched by the ILO has been to seek to eliminate child labour throughout the world. In particular, the ILO is concerned about children who work in hazardous working conditions, bonded child labourers, and extremely young working children. It is trying to create a worldwide movement to combat the problem by: ➤ implementing measures which will prevent child labour ➤ withdrawing children from dangerous working conditions ➤ providing alternatives, and ➤ improving working conditions as a transitional measure towards the elimination of child labour.

18.2.1

ILO Conventions and Recommendations

The international labour standards were developed for four reasons. The main motivation was to improve working conditions with respect to health and safety and career advancement. The second motivation was to reduce the potential for social unrest as industrialization progressed. Thirdly, the member States want common standards so that no single country has a competitive advantage over another due to poor working conditions. Finally, the union of these countries creates the possibility of a lasting peace based on social justice. International labour standards are adopted by the International Labour Conference. They take the form of Conventions and Recommendations. At the present time, there are 187 Conventions and 198 Recommendations, some of which date back to 1919. International labour standards contain ﬂexibility measures to take into account the different conditions and levels of development among member States. However, a Government that ratiﬁes a Convention must comply with all its articles. Standards reﬂect the different cultural and historical backgrounds of the member states as well as their diverse legal systems and levels of economic development. ILO Conventions are international treaties signed by ILO member States and each country has an obligation to comply with the standards that the Convention establishes. In contrast, ILO Recommendations are nonbinding instruments that often deal with the same topics as Conventions. Recommendations are adopted when the subject, or an aspect of it, is not considered suitable or appropriate at that time for a Convention.

International aspects of health and safety Recommendations guide the national policy of member States so that a common international practice may develop and be followed by the adoption of a Convention. ILO standards are the same for every member State and the ILO has consistently opposed the concept of different standards for different regions of the world or groups of countries. The standards are modiﬁed and modernized as needed. The Governing Body of the ILO periodically reviews individual standards to ensure their continuing relevance. Supervision of international labour standards is conducted by requiring the countries that have ratiﬁed Conventions to periodically present a report with details of the measures that they have taken, in law and practice, to apply each ratiﬁed Convention. In parallel, employers’ and workers’ organizations can initiate contentious proceedings against a member State for its alleged noncompliance with a convention it has ratiﬁed. In addition, any member country can lodge a complaint against another member State which, in its opinion, has not ensured in a satisfactory manner the implementation of a Convention which both of them have ratiﬁed. Moreover, a special procedure exists in the ﬁeld of freedom of association to deal with complaints submitted by governments or by employers’ or workers’ organizations against a member State whether or not the country concerned has ratiﬁed the relevant Conventions. Finally, the ILO has systems in place to examine the enforcement of international labour standards in speciﬁc situations. The ILO also publishes codes of practice and guidelines on health and safety matters. Those relevant to the International General Certiﬁcate are: ➤ Safety and Health in Construction (ILO Code of Practice) ➤ Ambient factors in the Workplace (ILO Code of Practice) ➤ Safety in the Use of Chemicals at Work (ILO Code of Practice) ➤ Recording and Notiﬁcation of Occupational Accidents and Diseases ➤ Ergonomic Checkpoints ➤ Work Organization and Ergonomics ➤ Occupational Safety and Health Management Systems (ILO guidelines). Important ILO Conventions (C) and Recommendations (R) in the ﬁeld of occupational safety and health include: ➤ C 115 Radiation Protection and (R 114), 1960 ➤ C 120 Hygiene (Commerce and Ofﬁces) and (R 120), 1964 ➤ C 139 Occupational Cancer and (R 147), 1974 ➤ C 148 Working Environment (Air, Pollution, Noise and Vibration) and (R 156), 1977

➤ C 155 Occupational Safety and Health and (R164), 1981 ➤ C 161 Occupational Health Services and (R 171), 1985 ➤ C 162 Asbestos and (R 172), 1986 ➤ C 167 Safety and Health in Construction and (R 175), 1988 ➤ C 170 Chemicals and (R 177), 1990 ➤ C 174 Prevention of Major Industrial Accidents and (R 181), 1993 ➤ C 176 Safety and Health in Mines and (R 176), 1995 ➤ C 184 Safety and Health in Agriculture and (R 192), 2001 ➤ C 187 Promotional Framework for Occupational Safety and Health and (R 197), 2006 ➤ R 97 Protection of Workers’ Health Recommendation, 1953 ➤ R 102 Welfare Facilities Recommendation, 1956 ➤ R 31 List of Occupational Diseases Recommendation, 2002

18.3 Major occupational health and safety management systems There are three major occupational health and safety management systems that are in use globally. These are: ➤ HSG 65 which has been developed by the UK HSE and is described in Chapter 1.15. The syllabuses for both Certiﬁcate courses and the management chapter headings in this text book have followed the elements of HSG 65 ➤ OHSAS 18001 has been developed by the British Standards Institute from its Recommended occupational health and safety management system BS 8800. It has been developed in conjunction with the ISO 9000 series for quality management and the ISO 14000 series for environmental management ➤ ILO-OSH 2001 was developed by the International Labour Organization (ILO) after an extensive study of many occupational health and safety management systems used across the world. It was established as an international system following the publication of ‘Guidelines on occupational safety and health management systems’ in 2001. It is very similar to OHSAS 18001.

18.3.1 Basic elements of all health and safety management systems All recognized occupational health and safety management systems have some basic and common elements. These are: ➤ a planning phase ➤ a performance phase

405

Introduction to Health and Safety at Work ➤ a performance assessment phase ➤ a performance improvement phase.

The planning phase The planning phase always includes a policy statement which outlines the health and safety aims, objectives and commitment of the organization and lines of responsibility. Hazard identification and risk assessment takes place during this phase and the signiﬁcant hazards may well be included in the policy statement. It is important to note that in some reference texts, in particular those in languages other than English, the whole process of hazard identiﬁcation, risk determination and the selection of risk reduction or control measures is termed ‘risk assessment’. However, all three occupational health and safety management systems described in this chapter refer to the individual elements of the process separately and uses the term ‘risk assessment’ for the determination of risk only. At the planning stage, emergency procedures should be developed and relevant health and safety legal requirements and other standards identiﬁed together with appropriate benchmarks from similar industries. An organizational structure must be deﬁned so that health and safety responsibilities are allocated at all levels of the organization and issues such as competent persons and health and safety training are addressed. Realistic targets should be agreed within the organization and be published as part of the policy.

The performance phase The performance phase will only be successful if there is good communication at and between all levels of the organization. This implies employee participation as both worker representatives and on safety committees. Effective communication with the workforce, for example with clear safe systems of work and other health and safety procedures, will not only aid the implementation and operation of the plan but also produce continual improvement of performance – a key requirement of all occupational health and safety, quality and environmental management systems. There should also be effective communication with other stakeholders, such as regulators, contractors, customers and trade unions. The performance phase must be monitored on a regular basis since this will indicate whether there is an effective occupational health and safety management system and a good health and safety culture within the organization.

records of accident, work related injuries and ill-health as well as near miss and any enforcement notices. Any recommended remedial or preventative actions, following an investigation, must be implemented immediately and monitored regularly.

The performance improvement phase The performance improvement phase involves a review of the effectiveness of the health and safety management system and the identiﬁcation of any weaknesses. The review, which should be undertaken by the management of the organization, will assess whether targets have been met and the reasons for any under-performance. Issues such as the level of resources made available, the vigilance of supervisors and the level of co-operation of the workforce should be considered at the review stage. When recommendations are made, the review process must deﬁne a timescale by which any improvements are implemented and this part of the process must also be monitored. Continual improvement implies a commitment to improve performance on a proactive continuous basis without waiting for a formal review to take place. Most management systems include an audit requirement, which may be either internal or external. The audit process examines the effectiveness of the whole management process and may exercise as a control on the review process. Many inquiry reports into health and safety management issues have asserted that health and safety performance should be subject to audit in the same way that ﬁnancial performance must be audited. In the publication ‘Successful health and safety management – HSG 65’, the HSE recommend a similar four step approach to occupational health and safety management known as: Plan – establish standards for health and safety management based on risk assessment and legal requirements Do – implement plans to achieve objectives and standards Check – measure progress with plans and compliance with standards Act – review against objectives and standards and take appropriate action. The Plan-Do-Check-Act for occupational health and safety management forms the basis of the three occupational health and safety management systems HSG 65, OHSAS 18001 and ILO-OSH 2001.

The performance assessment phase

18.3.2 HSG 65

The performance assessment phase may be either active or reactive or, ideally, a mixture of both. Active assessment includes work based inspections and audits, regular health and safety committee meetings, feedback from training sessions and a constant review of risk assessments. Reactive assessment relies on

The UK HSE ﬁrst published ‘Successful health and safety management – HSG 65’ in 1991 and has amended it since then so that it is now more concerned with continual improvement and less with the attainment of minimum health and safety standards. Unlike the other two systems

406

International aspects of health and safety under consideration, HSG 65 was developed by a regulator (HSE) and, therefore, is much more widely recognized in the United Kingdom. Although HSE inspectors may use the framework of HSG 65 when auditing the health and safety management arrangements of an organization, it would be wrong, however, to assume that it is the only system recognized by the HSE. HSG 65 is shown in Figure 18.1. An outline of the ﬁve key elements of HSG 65 was given in Chapter 1 and is given in more detail here. The key elements are: 1.

2.

3.

A clear health and safety policy – Evidence shows that a well-considered policy contributes to business efﬁciency and continual improvement throughout the organization. It helps to minimize ﬁnancial losses arising from avoidable accidents and demonstrates to the workforce that accidents are not necessarily the fault of any individual member of the workforce. Such a management attitude could lead to an increase in workforce cooperation, job satisfaction and productivity. This demonstration of senior management involvement offers evidence to all stakeholders that responsibilities to people and the environment are taken seriously by the organization. A good health and safety policy helps to ensure that there is a systematic approach to risk assessment and sufﬁcient resources, in terms of people and money, have been allocated to protect the health and safety and welfare of the workforce. It can also support quality improvement programmes which are aimed at continual improvement. A well defined health and safety organization – The shared understanding of the organization’s values and beliefs at all levels of the organization, is an essential component of a positive health and safety culture. For a positive health and safety culture to be achieved, an organization must have clearly deﬁned health and safety responsibilities so that there is always management control of health and safety throughout the organization. The formal organizational structure should be such that the promotion of health and safety becomes a collaborative activity between the workforce, safety representatives and the managers. An effective organization will be noted for good staff involvement and participation, high quality communications, the promotion of competency, and the empowerment of all employees to make informed contributions to the work of the organization. A clear health and safety plan – This involves the setting and implementation of performance standards and procedures using an effective occupational health and safety management system. The plan is based on risk assessment methods to decide on priorities and set objectives for controlling or eliminating hazards and reducing risks. Measuring success

4.

5.

requires the establishing of performance standards against which achievements can be identiﬁed. The measurement of health and safety performance – This includes both active and reactive monitoring to see how effectively the occupational health and safety management system is working. Active monitoring involves looking at the premises, plant and substances plus the people, procedures and systems. Reactive monitoring discovers through investigation of accidents and incidents why controls have failed. It is also important to measure the organization against its own long term goals and objectives. The audit and review of health and safety performance – The results of monitoring and independent audits should be systematically reviewed to see if the management system is achieving the right results. This is not only required by the HSW Act, but is part of any company’s commitment to continual improvement. Comparisons should be made with internal performance indicators and the performance of external organizations with exemplary practices and high standards.

18.3.3 OHSAS 18001 OHSAS 18001 and ILO-OSH 2001 have many similarities in the details of the two systems. One of the biggest differences is that OHSAS 18001 is certiﬁable whereas ILO-OSH 2001 is not. OHSAS 18001, which is shown in Figure 18.7, was developed from the British Standard 8800 and was designed to be integrated with the two British Standards for quality and environmental management. Both occupational health and safety management systems have been shaped by internationally agreed occupational health and safety principles deﬁned in international labour standards and the European Union Framework Directive 89/391/EEC. OHSAS 18001:1999 requires an external audit as part of the certiﬁcation process. OHSAS 18002:2000 has also been produced by BSI as a guideline for implementation of OHSAS 18001. 18002 will be withdrawn when its contents are published as a British Standard. There are ﬁve elements in the OHSAS 18001 occupational health and safety management system: 1.

2.

Policy – The general requirements are similar to HSG 65 with the additional inclusions of a minimum compliance with national occupational safety and health laws and regulations and a willingness to consult fully with the workforce and their representatives. The policy statement should also refer to the need for continual improvement. Planning and organizing – The organization must establish effective arrangements for the

407

Introduction to Health and Safety at Work

Information link

Policy development

Policy

Control link

Organizing

Auditing

Organizational development

Planning and implementing

Measuring performance

Developing techniques of planning, measuring and reviewing

Reviewing performance Feedback loop to improve performance

Figure 18.5

Key elements of HSG 65.

4.

Figure 18.6 Sugar factory, Poland moving to 18001 accreditation.

3.

identiﬁcation, elimination or control of work-related hazards and risks and to promote health, safety and welfare at work. It should also include in its plan a procedure for the maintenance of a record of all relevant and current legal and other health and safety standards. Finally, the plan must address the health and safety objectives identiﬁed in the policy statement. Implementing and operation – As with HSG 65, there is a stress on the responsibility of senior management for the effective implementation and

408

5.

operation of the plan. This requires effective communication with and supervision of the workforce and the full participation of the workforce and their representatives. All procedures must be well documented and accessible by the workforce. Emergency procedures (including prevention) must be included within the system together with arrangements for the procurement of goods and services and the selection and supervision of contractors – see Chapter 3 for more information on this latter point. Checking and action for improvement – This is similar to the performance measurement phase of HSG 65. However, if possible, at the same time that any necessary corrective measures are noted, they should be introduced into the workplace processes and/or procedures. This is a good example of continual improvement. Management review – There must be an initial review after the introduction of the management system into the workplace. This initial review needs to identify all relevant national laws and regulations and any signiﬁcant hazards which might affect the workforce. It should check that adequate controls are in place and analyse any employee health surveillance records. It must be properly documented since it will form the base line from which continual improvement will be measured. At each subsequent management review, checks must be made on all work related injuries, ill-health, diseases and incidents to ensure that they have been properly logged

International aspects of health and safety

Policy

Planning

Continual improvement

Implementation and operation

Checking and corrective action

Management review

Figure 18.7

Key elements of OHSAS 18001.

and investigated by a competent person. The conclusions of such investigations should be monitored to ensure that any recommended remedial actions have been completed. The following actions should also be included during the review: ➤ an evaluation of the effectiveness of the management system in achieving the results required by the senior management of the organization ➤ the identiﬁcation of any changes required in the procedures or arrangements ➤ an evaluation of the progress made with the policy objectives ➤ a review of progress made with recommendations from earlier reviews ➤ a report to the health and safety committee for communication to the workforce. The OHSAS 18001 management system recognizes that the system is bound to require modiﬁcation and change as the activities of the organization change and national regulatory requirements change.

As mentioned earlier, the ILO-OSH 2001 guidelines offer a recommended occupational health and safety management system based on an ILO survey of several contemporary schemes including HSG 65 and OHSAS 18001. There are, therefore, many common elements between the three schemes. The guidelines are not legally binding and are not intended to replace national laws, regulations or accepted standards. At the national level, the guidelines should be used to establish a national framework for occupational health and safety management systems, preferably supported by national laws and regulations. They should also provide guidance for the development of voluntary arrangements to strengthen compliance with regulations and standards leading to continual improvement in occupational health and safety performance. The ILO recognizes that a management system can only be successful in a country if there is some form of national policy on health and safety and occupational health and safety management systems. The ILO recommends, therefore, that the following general principles and procedures be established: 1.

2.

3.

4. 5.

6. 7.

18.3.4 ILO-OSH 2001 The ILO has a considerable inﬂuence on the development of employment law in many countries across the world. As companies become more international in terms of both its markets and production bases, this inﬂuence of the ILO has increased and its working standards have become accepted in many parts of the world. Many of the ILO standards cover health and safety issues and are used in the International General Certiﬁcate course.

8.

The implementation and integration of occupational health and safety management systems as part of the overall management of an organization The introduction and improvement of voluntary arrangements for the systematic identiﬁcation, planning, implementation and improvement of occupational health and safety activities at both national and organizational levels The promotion of worker participation in occupational health and safety management at organizational level The implementation of continual improvement without unnecessary bureaucracy and cost The encouragement of national labour inspectors to support the arrangements at organizational level for a health and safety culture within the framework of an occupational health and safety management system The evaluation of the effectiveness of the national policies at regular intervals The evaluation of the effectiveness of occupational health and safety management systems within those organizations which are operating within the country The inclusions of all those affected by the organization, such as contractors, members of the public and temporary workers, at the same level of health and safety provision as employees.

Figure 18.8 shows the key elements of the ILO-OSH 2001 occupational health and safety management system. Each element will be discussed in turn but since it

409

Introduction to Health and Safety at Work has been developed from HSG 65 and OHSAS 18001 amongst other systems, there are many similarities. The elements are: 1.

2.

3.

Policy – There is a more speciﬁc emphasis on worker participation which it sees as an essential element of the management system and should be referenced in the policy statement. It is expected that workers and their health and safety representatives should have sufﬁcient time and resources allocated to them so that they can participate actively in each element of the management system. The formation of a health and safety committee is also a recommended part of the system. The occupational health and safety management system should be compatible with or integrated with other management systems operating in the organization. Organizing – There is much in common with both HSG 65 and OHSAS 18001 with responsibility, accountability, competence, training and communication being key parts of this element. There is a speciﬁc responsibility to provide effective supervision to ensure the protection of the health and safety of workers and to establish prevention and health promotion programmes. Workers should have access to any records, such as accident and monitoring records, which are relevant to their occupational health and safety. Training must be available to all members of the organization and be provided during normal working hours at no cost to employees. Planning and implementation – Unlike other systems, the ILO system combines planning and implementation. Following an initial review of any existing health and safety management system, a plan should be developed to remedy any deﬁciencies found. The plan should support compliance with national laws and regulations and include continual improvement of health and safety performance. It should contain measurable objectives which are realistic and achievable and, as with the other occupational health and safety management systems, hazard identiﬁcation and risk assessment. There should also be an adequate provision of resources and technical support. The plan must be capable of accommodating the impact on health and safety of any internal changes in the organization, such as new processes, new technologies and amalgamations with other organizations, or external changes due, for example, to changes in national laws or regulations. As with OHSAS 18001, emergency and procurement arrangements and detailed arrangements for the selection and supervision of contractors must be included in the health and safety plan.

410

4.

5.

6.

Evaluation – This is very similar to the performance measurement phase of HSG 65 with a greater emphasis on the health and welfare of the worker. The recommendations concerning the investigation of work-related injuries, ill-health, diseases and incidents are identical to those for the management review element of OHSAS 18001. Action for improvement – Arrangements should be introduced and maintained for any preventative and corrective action to be undertaken identiﬁed by performance monitoring, audits and management reviews of the health and safety management system. Arrangements should also be in place for the continual improvement of the management system. More details on the factors to be considered for continual improvement are given later in this chapter. Audit – The ILO recommend that an audit should be performed by competent and trained personnel at agreed and regular intervals. It should cover all elements of the management system including worker participation, communication, procurement, contracting and continual improvement. The audit conclusions must state whether the health and safety management system is effective in meeting the organizational health and safety policy and objectives and promotes full worker participation. The audit should also check that there is compliance with national laws and regulations and that there has been a satisfactory response to earlier audit ﬁndings.

It is clear that there is much that is common between the three management systems discussed and any differences are differences in emphasis. HSG 65 was the ﬁrst of the three systems and the emphasis was on legal compliance. OHSAS 18001 introduced the concept of continual improvement, integration with other management systems

Policy

Organizing

Audit

Planning and implementation

Continual improvement

Evaluation

Action for improvement

Figure 18.8

Key elements of ILO-OSH 2001.

International aspects of health and safety and certiﬁcation. ILO-OSH 2001 combines the features of HSG 65 and OHSAS 18001 and stresses the importance of worker participation for the system to be effective.

system must be effective in reducing risks in the workplace else it will be nothing more than a paper exercise.

18.4.2 The involvement of stakeholders

18.4 Other key characteristics of a health and safety management system The four basic elements common to all occupational health and safety management systems, as described earlier in this chapter, contain the different activities of the system together with the detailed arrangements and activities required to deliver those activities. However, there are four key characteristics of a successful occupational health and safety management system: ➤ ➤ ➤ ➤

a positive health and safety culture the involvement of all stakeholders an effective audit continual improvement.

18.4.1 A positive health and safety culture In Chapter 4, the essential elements for a successful health and safety culture were detailed and discussed. In summary, they were: ➤ leadership and commitment to health and safety throughout the organization ➤ an acceptance that high standards of health and safety are achievable ➤ the identiﬁcation of all signiﬁcant hazards facing the workforce and others ➤ a detailed assessment of health and safety risks in the organization and the development of appropriate control and monitoring systems ➤ a health and safety policy statement outlining short and long term health and safety objectives. Such a policy should also include national codes of practice and health and safety standards ➤ relevant communication and consultation procedures and training programmes for employees at all levels of the organization ➤ systems for monitoring equipment, processes and procedures and the prompt rectiﬁcation of any defects found ➤ the prompt investigation of all incidents and accidents and reports made detailing any necessary remedial actions. Some of these essential elements form part of the health and safety management system but unless all are present within the organization, it is unlikely that occupational health and safety will be managed successfully no matter which system is introduced. The chosen management

There are a number of internal and external stakeholders of the organization, who will have an interest and inﬂuence on the introduction and development of the occupational health and safety management system. The internal stakeholders include: ➤ Directors and trustees of the organization – Following several reports on corporate governance in recent years culminating in the Combined Code of Corporate Governance 2003, the measurement of occupational health and safety performance and the attainment of health and safety targets has been recognized as being as important as other measures of business performance and targets. A report on health and safety performance should be presented at each board meeting and be a periodic agenda item for sub-committees of the board such as audit and risk management. ➤ The workforce – Without the full cooperation of the workforce, including contractors and temporary employees, the management of health and safety will not be successful. The workforce is best qualiﬁed to ensure and provide evidence that health and safety procedures and arrangements are actually being implemented at the workplace. So often this is not the case even though the occupational health and safety managements system is well designed and documented. Worker representatives can provide useful evidence on the effectiveness of the management system at shop ﬂoor level and they can also provide a useful channel of communication between the senior management and the workforce. One useful measure of the health and safety culture is the enthusiasm with which workers volunteer to become and continue to be representatives. For a representative to be really effective, some training is essential. Organizations which have a recognized trade union structure will have fewer problems with ﬁnding and training worker representatives. More information on the duties of worker representatives is given in Chapter 3. ➤ Health and safety professionals – Such professionals will often be appointed by the organization to manage the occupational health and safety management system and monitor its implementation. They will, therefore, have a particular interest in the development of the system, the design of objectives and the deﬁnition of targets or goals. Unless they have a direct line management responsibility which is not very common, they can only act as advisers. The appointed

411

Introduction to Health and Safety at Work health and safety professional also liaises with other associated competent persons, such as for electrical appliance and local exhaust ventilation testing. External stakeholders include ➤ Insurance companies – As compensation claims increase, insurance companies are requiring more and more evidence that health and safety is being effectively managed. There is increasing evidence that insurance companies are becoming less prepared to offer cover to organizations with a poor health and safety record and/or occupational health and safety management system. ➤ Investors – Health and safety risks will, with other risks, have an effect on investment decisions. Increasingly, investment organizations require evidence that these risks are being addressed before investment decisions are made. ➤ Regulators – In many parts of the world, particularly in the Far East, national regulators and legislation require certiﬁcation to a recognized international occupational health and safety management system standard. In many countries, regulators use such a standard to measure the awareness of a particular organization to health and safety issues. ➤ Customers – Customers and others within the supply chain are increasingly insisting on some form of formal occupational health and safety management system to exist within the organization. The construction industry is a good example of this trend. Much of this demand is linked to the need for corporate social responsibility and its associated guidelines on global best practice. ➤ Neighbours – The extent of the interest of neighbours will depend on the nature of the activities of the organization and the effect that these activities have on them. The control of noise, dust and other atmospheric contaminants are examples of common problem areas which can only be addressed on a continuing basis using a health and safety management system. ➤ International organizations – The United Nations, the ILO, the International Monetary Fund, the World Bank and the World Health Organization are all examples of international bodies which have shown a direct or indirect interest in the management of occupational health and safety. In particular, the ILO is keen to see minimum standards of health and safety established around the world. The ILO works to ensure for everyone the right to work in freedom, dignity and security – which includes the right to a safe and healthy working environment. More than 70 ILO Conventions and recommendations relate to questions of safety and health. In addition the ILO has issued more than 30 Codes of Practice on

412

Figure 18.9

Construction site – Sienna.

Occupational Health and Safety. For more information see their web site www.ilo.org/safework. There is a concern of many these international organizations that as production costs are reduced by relocating operations from one country to another, there is also a lowering in occupational health and safety standards. The introduction of internationally recognized occupational health and safety management systems will help to alleviate such fears.

18.4.3 An effective audit An effective audit is the ﬁnal step in the occupational health and safety management system control cycle. The ‘feedback loop’ produced by audit enables the reduction of risk levels and the effectiveness of the occupational health and safety management system to be improved. Audit is a business discipline which is frequently used in ﬁnance, environmental matters and quality and can equally well be applied to health and safety. It will check on the implementation of occupational health and safety management systems and the adequacy and effectiveness of the management arrangements and risk control systems. Audit is critical to a health and safety management system but is not a substitute for the essential dayto-day management of health and safety. The audit aims to establish that the three major components of any occupational health and safety management system are in place and operating effectively. It should show that: ➤ appropriate management arrangements are in place ➤ adequate risk control systems exist, are implemented, and consistent with the hazard proﬁle of the organization ➤ appropriate workplace precautions are in place.

International aspects of health and safety Where the organization is spread over a number of separate sites, the management arrangements linking the centre with these sites should be examined by the audit. Some elements of the occupational health and safety management system do not need to be audited as often as others. For example, an audit to verify the implementation of critical risk control systems should be made more frequently than an audit of the management arrangements for health and safety of the whole organization. Where there are complex workplace precautions in place, such as in the chemical industry, it may also be necessary to undertake technical audits. The audit programme should produce a comprehensive picture of the effectiveness of the health and safety management system in controlling risks. The programme must indicate when and how each component part will be audited. The audit team should include managers, safety representatives and employees. Such inclusiveness will help during the implementation of any audit recommendations. More detailed information on the auditing process is given in Chapter 7. When planning an audit, a decision has to be made as to whether to use internal or external auditors. When formal certiﬁcation is required either by the organization or the client, competent external auditors are essential. However, it is likely that in such cases, internal auditors will also be used. The advantage of using internal auditors is that they know the critical areas to monitor and will help to spread good practices around the organization. The disadvantages are that clients may question their independence and they may well be unaware of external benchmarks. These two disadvantages are the advantages of using external auditors. External auditors have the disadvantages that they do not know the organization, require much more documentation and can offer bland reports. It is also usually more expensive to use external rather than internal auditors. Auditor competence is an important issue and it is important that any auditors used, whether internal or external, are properly trained.

Continual improvement need not necessarily be done at high cost or add to the complexity of the management system. Its beneﬁts include: ➤ a decrease in the rate of injuries, ill-health and damage ➤ a reduction in the resources required to manage the system ➤ an acceptability of higher standards and an improved health and safety culture ➤ overall improvements in the management system itself. The simplest way to achieve continual improvement is to implement the recommendations of audits and management reviews, use benchmarks from similar organizations and any revised national or industrial guidelines. The workforce, managers and supervisors often have very good suggestions on ways to improve processes and procedures. Such suggestions will lead to improvements in the management system. Finally the health and safety committee can be a very effective vehicle for continual improvement particularly if working parties are used to investigate speciﬁc issues within an agreed timeframe.

18.4.4 Continual improvement Continual improvement has been mentioned several times in this chapter and is recognized as a vital element of all occupational health and safety management systems if they are to remain effective and efﬁcient as internal and external changes affect the organization. Internal changes may be caused by business reorganization, such as a merger, new branches and changes in products, or by new technologies, employees, suppliers or contractors. External changes could include new or revised legislation, guidance or industrial standards, new hazards or campaigns by regulators.

Figure 18.10 Have to consider different solutions in different countries – delivering furniture in Certaldo, Italy.

413

Introduction to Health and Safety at Work 18.5 The role of the regulatory authorities 18.5.1

The legal framework

The framework for regulating health and safety will vary across the world, for example, European countries use the EU framework, the Paciﬁc Rim countries tend to use a USA framework whereas the Caribbean countries follow the United Kingdom framework. The course provider should be able to describe the legal and regulatory framework appertaining to any particular country. Most legislation is driven by a framework of Acts, Regulations and support material including codes of practice and standards as illustrated in Figure 18.11. Within Europe there is another layer of legislation known as Directives, above the Member States own legislation. These are legally binding on each state, for more information see Chapter 1. The USA system of federal and individual state legislation is very similar.

18.5.2 Regulatory authorities and safety management systems The role of the national regulatory authority is crucial to the successful implementation of an occupational health and safety management system. In many parts of the world, such as South East Asia, formal adoption of a recognized management system is required with third party auditing by Government approved auditors. In the USA, organizations with approved management systems may be exempted from normal inspections by the Occupational Safety and Health Administration. In the United Kingdom, there has been a movement from prescriptive legislation to risk assessment by the

employer and this movement is now occurring in many parts of the world including the EU. A management system is an essential tool to achieve this movement and such a system is implied in the UK Management of Health and Safety at Work Regulations. Countries such as Canada, Australia, New Zealand and Norway have developed occupational health and safety management systems as an encouragement for such self regulation. The ILO-OSH 2001 system has been adopted by Germany, Sweden, Japan, Finland, Korea, China, Mexico, Costa Rica, Brazil, Indonesia, Vietnam, Malaysia, India, Thailand, The Czech Republic, Poland and Russia. It is likely that more countries and multinational companies will expect occupational health and safety management systems to be adopted either as a legal duty or an implied duty following ruling from local courts of law.

18.6 The benefits and problems associated with occupational health and safety management systems Occupational health and safety management systems have many beneﬁts of which the principal ones are: 1.

2.

3. 4. ACTS

REGULATIONS Mandatory

5. 6.

CODES OF PRACTICE Sometimes mandatory as Approved Codes of Practice in UK

NATIONAL AND INTERNATIONAL STANDARDS INDUSTRY STANDARDS AND GUIDANCE NOTES Voluntary Guidance

Figure 18.11

414

Typical health and safety legal framework.

It is much easier to achieve and demonstrate legal compliance. Enforcement authorities have more conﬁdence in organizations which have a health and safety management system in place. It ensures that health and safety is given the same emphasis as other business objectives, such as quality and ﬁnance. It will also aid integration, where appropriate, with other management systems. It enables signiﬁcant health and safety risks to be addressed in a systematic manner. It can be used to show legal compliance with terms such as ‘practicable’ and ‘so far as is reasonably practicable’. It indicates that the organization is prepared for an emergency. It illustrates that there is a genuine commitment to health and safety throughout the organization.

There are, however, several problems associated with occupational health and safety management systems although most of them are resolvable. The main problems are: 1.

The arrangements and procedures are not apparent at the workplace level and the audit process is only concerned with a desk top review of procedures

International aspects of health and safety 2.

3. 4.

5. 6.

The documentation is excessive and not totally related to the organization due to the use of generic procedures Other business objectives, such as production targets, lead to ad hoc changes in procedures Integration, which should really be a beneﬁt, can lead to a reduction in the resources and effort applied to health and safety A lack of understanding by supervisors and the workforce leading to poor system implementation The performance review is not implemented seriously thus causing cynicism throughout the organization.

18.7 Conclusions on the three health and safety management systems Three occupational health and safety management systems have been described in some detail in this chapter and it has been shown that the similarities between them outweigh their differences. Any occupational health and safety management system will fail unless there is a positive health and safety culture within the organization and the active involvement of internal and external stakeholders. A structured and well-organized occupational health and safety management system is essential for the maintenance of high health and safety standards within all organizations and countries. Some systems, such as OHSAS 18001, offer the opportunity for integration with quality and environmental management systems. This enables a sharing of resources although it is important that technical activities, such as health and safety risk assessment, are only undertaken by persons trained and competent in that area. For an occupational health and safety management system to be successful, it must address workplace risks and be ‘owned’ by the workforce. It is, therefore, essential that the audit process examines shop ﬂoor health and safety behaviour to check that it mirrors that required by the health and safety management system. Finally, whichever system is adopted, there must be continual improvement in health and safety performance if the application of the occupational health and safety management system is to succeed in the long term.

18.8 Other minor additions to the International General Certificate The sources of health and safety information have been extended to include information provided by the websites or publicity ofﬁces of national or international

Figure 18.12

Mobile tower crane – Cinque Terre, Italy.

agencies (e.g. International Labour Organisation (ILO), Occupational Safety and Health Administration (USA), European Agency for Safety and Health at Work (EU) and Worksafe (Western Australia)). The sources of information covered in Chapter 1 are also included. The hazards of working in unfamiliar countries and/or climates are important health and safety issues – snake bites, diseases (such as malaria and yellow fever) and

415

Introduction to Health and Safety at Work sunstroke. Again the course provider will relate these hazards to the country in question. Finally fault and no-fault compensation schemes have been included in the International General Certiﬁcate syllabus.

18.8.1 Fault and no-fault compensation In the United Kingdom, compensation for an injury following an accident is achieved by means of a successful legal action in a civil court (as discussed in Chapter 1). In such cases, injured employees sue their employer for negligence and the employer is found liable or at fault. This approach to compensation is adversarial, costly and can deter injured individuals of limited means from pursuing their claim. In a recent medical negligence claim in Ireland, costs were awarded against a couple, who were acting on behalf of their disabled son, and they were faced with a bill for £ 3 m. The spiralling cost of insurance premiums to cover the increasing level and number of compensation awards, despite the Woolfe reforms (see Chapter 15), has led to another debate on the introduction of a no-fault compensation system. It has been estimated that in medical negligence cases, it takes on average six years to settle a claim and only 10% of claimants ever see any compensation. No-fault compensation systems are available in many parts of the world in particular New Zealand and several States in the USA. In these systems, amounts of compensation are agreed centrally at a national or State level according to the type and severity of the injury. The compensation is often in the form of a structured continuous award rather than a lump sum and may be awarded in the form of a service, such as nursing care, rather than cash. The no-fault concept was ﬁrst examined in the 1930s in the USA to achieve the award of compensation quickly in motor car accident claims without the need for litigation. It was introduced ﬁrst in the State of Massachusetts in 1971 and is now mandatory in nine other States although several other States have either repealed or modiﬁed no-fault schemes. In 1978, the Pearson Commission in the United Kingdom rejected a no-fault system for dealing with clinical negligence even though it acknowledged that the existing tort system was costly, cumbersome and prone to delay. Its principal reasons for rejection were given as the difﬁculties in reviewing the existing tort liability system and in determining the causes of injuries. In New Zealand, there was a general dissatisfaction with the workers compensation scheme which was similar to the adversarial fault-based system used in Australia and the United Kingdom. In 1974, a no-fault accident compensation system was introduced

416

and administered by the Accident Compensation Corporation (ACC). This followed the publication of the Woodhouse Report in 1966 which advocated a 24 hour accident cover for everybody in New Zealand. The Woodhouse Report suggested the following ﬁve principles for any national compensation system: ➤ ➤ ➤ ➤ ➤ ➤

community responsibility comprehensive entitlement irrespective of income or job status complete rehabilitation for the injured party real compensation for the injured party administrative efﬁciency of the compensation scheme

The proposed scheme was to be ﬁnanced by channelling all accident insurance premiums to one national organization (the ACC). The advantages of a no-fault compensation scheme include: 1. 2. 3. 4.

5.

Accident claims are settled much quicker than in fault schemes Accident reporting rates will improve Accidents become much easier to investigate because blame is no longer an issue Normal disciplinary procedures within an organization or through a professional body are unaffected and can be used if the accident resulted from negligence on the part of an individual More funds are available from insurance premiums for the injured party and less used in the judicial and administrative process.

The possible disadvantages of a no-fault compensation system are: 1. 2. 3.

4. 5.

There is often an increase in the number of claims, some of which may not be justiﬁed There is a lack of direct accountability of managers and employers for accidents Mental injury and trauma are often excluded from no-fault schemes because of the difﬁculty in measuring these conditions There is a difﬁculty in deﬁning the causes of many injuries and industrial diseases The monetary value of compensation awards tend to be considerably lower than those in fault schemes (although this can be seen as an advantage).

No-fault compensation schemes exist in many countries including Canada and the Scandinavian countries. However a recent attempt to introduce such a scheme in New South Wales, Australia was defeated in the legislative assembly.

International aspects of health and safety 18.9 Practice NEBOSH questions for the International General Certificate The International General Certiﬁcate is a new award and all examination papers to date (February 2005) have used questions taken from the question bank for the National General Certiﬁcate other than those questions directly related to UK law. Therefore, all practice questions given at the end of each chapter in this book can be used by students on the International General Certiﬁcate except those at the end of Chapter 1 which relate to UK law. The questions at the end of Chapter 1 which may be used on the International General Certiﬁcate are given below. 1. (a)

Draw a ﬂowchart to identify the main components of the health and safety management

system described in the HSE publication “Successful Health and Safety Management” (HSG65). (b) Outline TWO components of the health and safety management system identiﬁed in (a). 2. Outline the economic beneﬁts that an organization may obtain by implementing a successful health and safety management system.

3. (a)

Draw a ﬂowchart to show the relationships between the SIX elements of the health and safety management model in HSE’s “Successful Health and Safety Management” (HSG65). (b) Outline the part that EACH element of the HSG65 model plays within the health and safety management system.

417

19 19.1 Introduction The NEBOSH certiﬁcate is like any other examination. To pass it there are several things a student needs to do. The best results can be achieved by planning in the following way: ➤ having clear and realistic goals, both in the short and the long term ➤ having knowledge of some techniques for studying and for passing exams ➤ having a well organized approach ➤ being motivated to learn. It is often said that genius is 99% application and only 1% inspiration. Good organization and exam technique are secondary to academic ability when it comes to passing exams. Studying is an activity in its own right and there are a number of ways in which students can make their study much more effective to give themselves the greatest possible chance of success. The place where a person studies; planning of study time; adapting the type of study to suit the individual; styles of note-taking; improving memory and concentration skills; revision techniques; being clear about the contents of the syllabus and about what is expected by the examiner; attention to all these details will maximize a student’s available time and mental ability.

19.2 Finding a place to study Studying does not always come naturally to people and it often has to be learned, so it is worth paying attention to the basics of study. It is easier to acquire the habit of study if the student works in a place that has been designated

418

Study skills

for the purpose. Choose somewhere reasonably quiet and free from distractions, with good ventilation (essential for alertness) and a comfortable temperature. Make sure there is enough light – a reading lamp helps to prevent eyestrain and tiredness. Choose an upright chair rather than an armchair and make sure that the workspace is large enough. The size recommended by Warwick University, for example, is a minimum of 60 cm 1.5 m. If possible, ﬁnd a place where study materials do not have to be cleared away as it is very easy to put off starting work if they are not instantly accessible.

19.3 Planning for study Start by making a study timetable. Planned study periods need to be established so that they do not get squeezed out of the busy working week. Depending on the type of syllabus being followed, the timetable will need to include time for carrying out assignments set by tutors, time for going over lecture notes and materials, any further reading rated as ‘essential’ and, if possible, reading rated as ‘desirable’. Time should also be allocated for revision as the course progresses because the more regularly the information is revised, the more ﬁrmly it will become ﬁxed in ‘long-term memory’. This makes it very much easier to recall information for an exam. After every hour of study, take a short break and, if possible, have a change of atmosphere. Physical exercise is very helpful in increasing the ability to concentrate and even a brisk walk round the block can do wonders for the attention span. Variation is another way of holding the attention, so it helps to alter the type of activity. For example, time could be spent gathering information from books, the

Study skills internet and so on, followed by drawing a diagram or a graph, writing, reading and so on.

19.4 Blocked thinking Sometimes a student becomes ‘blocked’ in an area of study. If this happens, try leaving it alone for a few days and tackle a different area of the subject, since concentrating too hard on something that is too difﬁcult is likely to produce loss of conﬁdence and can be very de-motivating. It usually happens that, having had a break, the difﬁculty vanishes and the problem clears. This is either because the solution has emerged in the mind from another perspective, or because the student has learnt something new that has supplied the answer. Psychologists consider that it is possible that some problems can be solved during sleep when the mind has a chance to wander and apply lateral thinking.

19.5 Taking notes The most efﬁcient way to store notes is in a loose-leaf folder, because items can so easily be added. Write only on one side of the sheet and use margined paper to make it easier to add information. The facing pages can be used to make summaries or extra points. If notes are clearly written and well spaced out, they are much more straightforward to work from and more attractive to return to later. Use colour, highlighting and underlining too; notes that look good are less daunting when the time comes to revise. During revision it will be important to be able to identify subjects quickly, so use headings, numbering, lettering, bullet points, indentation and so on. It is worth spending a bit of extra time if it will make revision easier. Key words and phrases are better than continuous prose when note-taking. While writing down information it is easy to miss essential points that are being made by the tutor. The notes should be read through within 36 hours to make sure that they are completely clear when the time comes to revise. At this point it is convenient to add in anything that has been missed, while it is fresh in the mind. Reading through notes in this way also helps to ﬁx the information in the memory and the level of recall will be further improved by reading them again a week later. Although it seems time-consuming, this technique will save a lot of time in the long term. Many people ﬁnd that they can understand and remember more effectively by making ‘mind maps’ (also known as ‘pattern notes’). These will be discussed in more detail in the revision section.

19.6 Reading for study It is very rarely necessary to read a whole book for study purposes. Use the index and be selective. Since most students will be working while they are studying, they will need techniques to help them make the most effective use of their time. Skim reading is a great time-saver. First of all, ﬂip through the book to see what it contains, looking at the contents, summaries, introduction, tables, diagrams and so on. It should be possible to identify areas that are necessary to the syllabus. These can be marked with removable adhesive strips or ‘post-it’ notes. Secondly, quickly read through the identiﬁed parts of the book. Two ways of doing this are: (a) run a ﬁnger slowly down the centre of a page, watching it as it moves. The eye will pick up relevant words and phrases as the ﬁnger moves down (b) read in phrases, rather than word by word, which will increase the reading speed. Both these methods need practise but they save a lot of time and effort, and it is better to read through a piece two or three times, quickly, than to read it once slowly. However, if there is a really difﬁcult piece of information that is absolutely essential to understand, reading it aloud, slowly, will help. ➤ Finally, at the end of each section or chapter, make a few brief notes giving the essential points. It is well worth learning to speed read if a course involves a large amount of reading. Tony Buzan’s series ‘The Mind Set’ explains the technique in simple terms.

19.7 Organizing for revision As the exam approaches, all the information from the course needs to be organized in preparation for revision. This should, ideally, have been an ongoing process throughout the course, but if not there will be extra work to be undertaken at this point. Information from lectures, reading, practical experience and assignments needs to be organized into a form that makes it readily accessible to the memory. In addition there will be the student’s existing knowledge that is relevant to the syllabus. It is worth spending some time considering how this store of information relates to and can be used to expand and back up the new information from the course. December

419

Introduction to Health and Safety at Work 2005 Examiners’ Reports refer speciﬁcally to the advantages to be gained from this: Paper A1 Question 4 ‘Some candidates, perhaps from their work experience, showed a good knowledge of a permit-to-work system and produced reasonable answers’ They also warn of the dangers: ‘Answers based solely on “what we do in our organization” … do not earn high marks’.

19.8 Organizing information There are a number of ways to organize information for an exam: ➤ reading back through the notes on a regular basis while the course is still in progress will help to ﬁx the information in long-term memory ➤ make revision cards: condensing the information down so that it ﬁts on a set of postcards makes it possible to carry a lot of information around in a pocket. The activity of condensing the information is revision in itself. The revision material is then available for spare moments in the day, such as queuing in the canteen, sitting in a trafﬁc jam on the motorway, waiting for the computer to function and so on. For example: ‘Outline the factors that may increase risks to pregnant employees’. On a card, the information could be condensed into:

itself. Because they are based on visual images they are easier for many people to remember and they can be made as complex or as simple as the individual requires. Using colour and imagery makes it easier to follow and to recall the information in a mind map (Buzan 2003). Figure 19.2 is a mind map based on the report writing section of this book ➤ use list words: for example, students were asked to list eight ways of reducing the risk of a ﬁre starting in the workplace. The examiners’ report suggested the following: ‘candidates could have chosen from a list including the control of smoking and smoking materials, good housekeeping to prevent the accumulation of waste paper and other combustible materials, regular lubrication of machinery, frequent inspection of electrical equipment for damage, ensuring ventilation outlets on equipment are not obstructed, controlling hot work, the provision to proper storage facilities for flammable liquids and the segregation of incompatible chemicals’ This list could be reduced to an eight-letter nonsense work, to jog the memory, as follows:

FLICSHEV: Flammable liquids – provide proper storage facilities Lubrication – regular lubrication of machinery Incompatible chemicals need segregation Control of hot work Smoking – of cigarettes and materials, to be controlled Housekeeping (good) – prevent accumulation of waste Electrical equipment – needs frequent inspection for damage Ventilation – outlets should not be obstructed

The effort involved in constructing this list and inventing the word helps to ﬁx the information in memory. There are other methods to aid memory but these four are probably the most practical aids to exam technique.

Figure 19.1

Revision notes.

➤ make mind-maps (also known as pattern notes): Like revision cards, the act of making them is revision in

420

19.9 How does memory work? Understanding how memory works will help the student to use it more effectively. As in any scientiﬁc subject,

Study skills

Figure 19.2

Mind map report writing.

there is still a lot to be discovered about the workings of the mind, and a considerable amount of disagreement about what has been discovered so far; but psychologists generally seem to agree about the way that memory works. The process of remembering is divided, roughly, into two sections – short term and long term memory. Items that go into short term memory, if no further attention is paid to them, will fade away and be forgotten. If they are rehearsed they will stay in short term memory for a while, as, for example, when trying to remember a phone number to make a call. To put something into long term memory demands a greater ‘depth of processing’, that is to say, more mental activity is required so that (a) information stays in the memory (storage) and (b) information can be found when it is needed (retrieval). The techniques described in the section entitled ‘Thinking about revision’ give some ways in which storage and retrieval systems in the brain can be made to work effectively.

Contrary to popular opinion, mature students have many assets when it comes to learning. Because their life and work experience is almost always more comprehensive and of a higher complexity than that of younger students, they normally possess more ‘schemas’ (areas of knowledge) to which new information can be attached. In addition to this there will be more experiences already stored in the brain that can provide an explanation for the new pieces of knowledge that are being acquired. Add to this a very high level of motivation, a stronger level of incentive towards success and more determined application, and it becomes clear that the mature student has many learning advantages. Research shows that, as learners, we take in 10% of what we read; 20% of what we hear; 30% of what we see; 50% of what we see and hear; 70% of what we ourselves say; 90% of what we ourselves do. It is easy to see that people who are working at and studying a subject have an advantage. It cannot be denied, however, that mature students tend to be very nervous about exams and often need

421

Introduction to Health and Safety at Work a good deal of reassurance and support to enable them to realize their full potential.

19.10 How to deal with exams

6. 7.

Try to eat and sleep well and take some exercise. Revision techniques are covered in the sections on revision and memory earlier in this chapter. SET REALISTIC TARGETS, THEN ACHIEVE THEM. MAKE PLANS AND STICK TO THEM

There are three stages to taking an exam:

19.10.2

➤ planning and revision ➤ the exam room ➤ after the exam.

➤ Read through the exam paper very carefully ➤ Check the instructions – how many questions have to be answered? From which section? ➤ Make a time plan ➤ Underline key words e.g. ‘deﬁne’, ‘describe’, ‘explain’, ‘identify’ and so on. NEBOSH provides deﬁnitions of the meanings of these in the examiners’ reports (see ‘Terminology’ section). Using the words in the question when writing the answers will help to keep the answer on track ➤ Stick to the instructions given in the question. If the question says ‘list’, then list; if it says ‘describe’, then describe. If it says ‘brieﬂy’ make sure the answer is brief ➤ Write clearly. Illegible answers don’t get marked ➤ Look at the number of marks allocated to a question to pick up clues as to how much time should be spent on it ➤ Mark questions which look possible and identify any that look impossible ➤ It is rarely necessary to answer exam questions in a particular order. Start with the question that you feel most comfortable with since it will help to boost conﬁdence. Make sure it is clearly identiﬁed by number for the examiner ➤ Answer the question that is set, not the one you wish was on the paper ➤ If ideas for other answers spring to mind while writing, jot down a reminder on a separate piece of paper. It is easy to forget that bit of information in the heat of the moment ➤ Plan the use of time and plan the answers. Include some time to check over each answer ➤ Stick to the time plan; stick to the point; make points quickly and clearly.

For people with special needs, there are provisions within NEBOSH to allow extra time or the use of special equipment. Students who think they may be eligible for help should apply to NEBOSH several weeks before the date of the exam.

19.10.1 1.

2.

3.

4.

5.

Planning and revision

It is absolutely essential for students to know what they are going to be examined on and what form the exam will take. Students should read through the syllabus and if they are concerned about any area of it, this should be raised with the course tutor well before the date of the exam. Read the examiners’ reports for the subject. After the exams every year, the examiners highlight the most common mistakes made by students (see section on examiners’ reports later in the article). They also provide useful information about, for example, pass rates, levels attained (distinction, credit, pass, fail) time management and other hints on exam technique. It is very useful to work through some recent past papers, against the clock, to get used to the ‘feel’ of the exam. If possible, tutors should set up mock exams and make sure that the papers are marked. Some of the shorter courses will not be able to provide this service, and if this is the case, students should try to do at least one or two questions in their own time. The examiners’ reports will give an indication of what could have gone into the answers. Past papers, examiners’ reports and syllabuses are available from NEBOSH. The web site is at www.nebosh.org.uk. It is vital to know where the exam is to be held and the date and time. If possible, visit the building beforehand to help build conﬁdence about the location, availability of parking and so on. Make a chart of the time leading up to the exam. Include all activities, work, leisure, social, as well as the time to be used for revision, so that the schedule is realistic.

422

In the exam room

Early marks in an exam question are easier to pick up than the last one or two, so make sure that all the questions are attempted within the time plan. No marks are given for correct information that is not relevant to the question. Examiners are only human and usually have to work under pressure; it is quite possible that some vital and correct point may be missed if there is a mass of irrelevant information from which the point has to be extracted. Don’t be distracted by the behaviour of other students. Someone who is requesting more paper has

Study skills not necessarily written a better answer; they may simply have larger handwriting. People who start to scribble madly as soon as they turn over the question sheet are not in possession of some extra ability – they simply haven’t planned their exam paper properly. Keep calm, plan carefully, don’t panic. At the end of the exam, before handing in the paper, make sure that anything that is not intended for marking is crossed through.

*Terminology used in NEBOSH exams (Taken from the guide to the NEBOSH National General Certiﬁcate October 2003 Appendix 3) Action verb define

describe explain give

identify list outline

sketch

state

19.10.3

Meaning provide a generally recognized or accepted deﬁnition give a word picture give a clear account of, or reasons for provide without explanation (used normally with the instruction to ‘give an example [or examples] of. . .) select and name provide list without explanation give the most important features of (less depth than either ‘explain’ or ‘describe’ but more depth than ‘list’) provide a simple line drawing using labels to identify speciﬁc features a less demanding form of ‘deﬁne’, or where there is no generally recognized deﬁnition

After the exam

If there are several exams to be taken, it is important to keep conﬁdence levels high. It is not a good idea to get into discussion about other peoples’ experiences of the exam. After one exam, focus on the next. If something went wrong during the exam (for example, illness or severe family problems), the tutor and the examining board should be alerted immediately.

19.11 The examiners’ reports 19.11.1

A few points from the examiners’ reports

The latest reports available at the time of going to press are for March and June 2006. As in previous years, the examiners acknowledge the achievements and hard work of candidates, but they point out that avoidable mistakes are still being made and marks lost, simply through lack of examination technique. The examiners advise that while acquisition of knowledge and understanding across the syllabus are clearly a prerequisite for success, examination technique is an essential. They deﬁne this as ‘the skill of reading a question, identifying the breadth of issues relevant to deﬁne that question and putting them down on paper in a logical and coherent way and to the depth required’. Effective time planning is also emphasized. The final page of each of the examiner’s reports gives a clearly worded guide to examination technique. Here are some examples from the reports that show how good examination technique could have improved candidates’ chances of gaining higher marks: Paper A1 March 2006 asked candidates to outline the issues that should be included in a training programme … on the emergency action to be taken in the event of ﬁre. Some candidates lost marks by including irrelevant information such as the ﬁre triangle and ﬁre risk assessment, others concentrated exclusively on the content of a training programme. In another question, asking about the physical features of trafﬁc routes, some candidates did not restrict their answers to this but included irrelevant material about vehicles and their drivers. There are a number of examples of answers being limited to one or two topics when writing about a range of issues could have gained a lot of extra marks. For example, again in March 2006, a maximum of eight marks could have been gained by describing four personal factors that may place young persons at risk and outlining four measures that could reduce accidents to them. Some candidates concentrated only on one or two topics, thus losing several marks. Misreading the question crops up year after year and 2006 was no exception. Asked to outline ways to help ensure the effectiveness of a health and safety committee, several candidates gave answers relating to a safety representative. Asked to identify symptoms in another question, several people concentrated on diseases. The report on the June 2006 paper says of one question ‘those who read the question with care and focused closely on what was being asked … generally provided good answers’. And later ‘again, many candidates

423

Introduction to Health and Safety at Work did not read the question with sufﬁcient care … and provided a list rather than an outline’. Being clear about terminology is essential. In a question with a possible 10 marks, many candidates lost out because they were not clear about the terms ‘immediate causes’ and ‘root causes’ in the question. In another question, candidates asked to ‘outline the main hazards’ instead discussed precautions and control methods. The question carried eight marks. Another question asked for an explanation of the purpose and beneﬁts of collecting ‘near-miss’ incident data but several people confused the meanings of ‘purpose’ and ‘beneﬁts’ in their answer. In a question on the effects to health of exposure to ionising radiation, the report describes ‘a tendency by some candidates to write down every possible health effect they could think of in the hope that some might be caused by radiation’.

19.12 Conclusion Passing health and safety exams and assessments has a lot in common with any other subject being examined.

424

If candidates do not apply themselves to study effectively, read the answers carefully and plan their answers, success will be very limited. As once said by an old carpenter: ‘Measure twice, think twice and cut once’ Applied to exams it can be changed to: ‘Read twice, think twice and write once’

19.13 References Buzan, Tony: The Mind Set BBC Worldwide 2000 (includes Use your head, Master your memory, The speed reading book, and Use your memory). Elson, D. and Turnbull, G.: How to do better in exams, AEB1989. Leicester, Coventry and Nottingham Universities study skills booklets. NEBOSH Examiners’ reports. Guide to the NEBOSH National General Certificate. Northedge, Andrew: The Good Study Guide, The Open University 2005.

Specimen answers to NEBOSH examinations

20.1 Introduction The NEBOSH National General Certiﬁcate is assessed by two written examination papers (NGC1 – The management of health and safety; and NGC2 – Controlling workplace hazards) and a practical assessment (NGC3 – The practical application). Both examination papers and the practical application must be passed so that the NEBOSH National General Certiﬁcate may be awarded. In this chapter, specimen answers are given to one long and two short questions for each of the two written papers. A specimen practical assessment and management report is also given for the practical application. It is important to stress that there are no unique answers to these questions but the answers provided should provide a useful guide to the depth and breadth expected by the NEBOSH examiners. Candidates are strongly advised to read past examiners’ reports which are published by NEBOSH. These are very useful documents because they not only give an indication of the expected answers to each question of a particular paper but they also indicate some common errors made by candidates.

20.2 The written examinations The previous chapter on study skills gives some useful advice on tackling examinations and should be read in conjunction with this chapter. Particular attention should be paid to terminology used in NEBOSH examinations and the meaning of the action verbs used in the questions. Candidates have always had most difﬁculty with the action verb ‘outline’ and, for this reason, several of

20

the specimen questions chosen use ‘outline’ so that some guidance on the depth of answer expected by the examiners can be given. It is difﬁcult to give a deﬁnitive guide on the exact length of answer to the examination questions because some expected answers will be longer than others. As a general guide, for the long answer question on the examination paper, it should take about 25 minutes to write about one and a half pages (550 to 620 words). Each of the ten short answer questions require about half a page of writing (170 to 210 words). While candidates may not be guaranteed 100% by following the guidance in this chapter, they should obtain a comfortable pass.

20.2.1

NGC1 – The management of health and safety

Paper 1 – Question 1 (a) Outline the factors that should be considered when selecting individuals to assist in carrying out risk assessments in the workplace. (5) (b) Describe the key stages of a general risk assessment. (5) (c) Outline a hierarchy of measures for controlling exposures to hazardous substances. (10)

Answer: (a) The most important factor is the competence and experience of the individuals in hazard identiﬁcation and risk assessment. Some training in these areas should offer evidence of the required competence. They should be experienced in the process or activity under assessment and have technical knowledge

425

Introduction to Health and Safety at Work

Figure 20.1

Ladders should be correctly angled

of any plant or equipment used. They should have knowledge of any relevant standards, HSE guidance and regulations relating to the activity or process. They must be keen and committed but also aware of their own limitations. They need good communication skills and be able to write interesting and accurate reports based on evidence and the detail found in health and safety standards, codes

426

of practice, regulations and guidance. Some IT skills would also be advantageous. Finally, the views of their immediate supervisor should be sought before they are selected as team members. (b) There are ﬁve key stages to a risk assessment suggested by the HSE as follows: The ﬁrst stage is hazard identiﬁcation which involves looking at signiﬁcant hazards which could

Specimen answers to NEBOSH examinations result in serious harm to people. Trivial hazards should be ignored. This will involve touring the workplace concerned looking for the hazards in consultation with workers themselves and also reviewing any accidents, ill health or incidents that have occurred. Stage 2 is to identify the person who could be harmed – this may be employees, visitors, contractors, neighbours or even the general public. Special groups at risk, like young persons, nursing or expectant mothers and people with a disability, should also be identiﬁed. Stage 3 is the evaluation of the risks and deciding if existing precautions or control measures are adequate. The purpose is to reduce all residual risks after controls have been put in to as low as is reasonably practicable. It is usual to have a qualitative approach and rank risks as high, medium or low after looking at the severity of likely harm and the likelihood of it happening. A simple risk matrix can be used to get a level of risk. The team should then consider whether the existing controls are adequate and meet any guidance or legal standards using the hierarchy of controls and the General Principles of Prevention set out in the Management Regulations. Stage 4 of the risk assessment is to record the signiﬁcant ﬁndings which must be done if there are ﬁve or more people employed. The ﬁndings should include any action that is necessary to reduce risks and improve existing controls – preferably set against a time scale. The information contained in the risk assessment must be disseminated to employees and discussed at the next health and safety committee meeting. Stage 5 is a time scale set to review and possibly revise the assessment which must also be done if there are signiﬁcant changes in the workplace or the equipment and materials being used. (c) The various stages of the usual hierarchy of risk controls are underlined in this answer. Elimination or substitution is the best and most effective way of avoiding a severe hazard and its associated risks. Elimination occurs when a process or activity is totally abandoned because the associated risk is too high. Substitution describes the use of a less hazardous form of the substance. There are many examples of substitution, such as the use of water-based rather than oil-based paints and the use of asbestos substitutes. In some cases it is possible to change the method of working so that exposures are reduced, such as, the use of rods to clear drains instead of strong chemicals. It may be possible to use the substance in a safer form; for example, in liquid or pellets to prevent dust from powders. Sometimes the

pattern of work can be changed so that people can do things in a more natural way; for example, by encouraging people in ofﬁces to take breaks from computer screens by getting up to photocopy or fetch documents. Reduced or limited time exposure involves reducing the time that the employee is exposed to the hazardous substance either by giving the employee other work or rest periods. If the above measures cannot be applied, then the next stage in the hierarchy is the introduction of engineering controls, such as isolation (using an enclosure, a barrier or guard), insulation (used on any electrical or temperature hazard) or ventilation (exhausting any hazardous fumes or gases either naturally or by the use of extractor fans and hoods). If ventilation is to be used, it must reduce the exposure level for employees to below the workplace exposure limit. Housekeeping is a very cheap and effective means of controlling risks. It involves keeping the workplace clean and tidy at all times and maintaining good storage systems for hazardous substances. A safe system of work is a requirement of the HSW Act and describes the safe method of performing the job. Training and information are important but should not be used in isolation. Information includes such items as signs, posters, systems of work and general health and safety arrangements. Personal protective equipment (PPE) should only be used as a last resort. There are many reasons for this. It relies on people wearing the equipment at all times and must be used properly. Welfare facilities, which include general workplace ventilation, lighting and heating and the provision of drinking water, sanitation and washing facilities, are the next stage in the hierarchy. All risk control measures, including training, and supervision must be monitored by competent people to check on their continuing effectiveness. Periodically the risk control measures should be reviewed. Monitoring and other reports are crucial for the review to be useful. Reviews often take place at safety committee and/or at management meetings. A serious accident or incident should lead to an immediate review of the risk control measures in place. Finally, special control requirements are needed for carcinogens.

Paper 1 – Question 2 Outline ways in which employers may motivate their employees to comply with health and safety procedures (8)

427

Introduction to Health and Safety at Work

Figure 20.2

Motivating staff (NEBOSH)

Answer: Motivation is the driving force behind the way a person acts or the way in which people are stimulated to act. The best way to motivate employees to comply with health and safety procedures is to improve their understanding of the consequences of not working safely, their knowledge of good safety practices and the promotion of their ownership of health and safety. This can be done by effective training (induction, refresher and continuous) and the provision of information showing the commitment of the organization to safety and by the encouragement of a positive health and safety culture with good communications systems. Managers should set a good example by encouraging safe behaviour and obeying all the health and safety rules themselves even when there is a difﬁcult conﬂict between production schedules and health and safety standards. A good working environment and welfare facilities will also encourage motivation. Involvement in the decision making process in a meaningful way, such as regular team brieﬁngs, the development of risk assessments and safe systems of work, health and safety meetings and effective joint consultation arrangements, will also improve motivation as will the use of incentive schemes. However, there are other important inﬂuences on motivation such as recognition and promotion opportunities, job security and job satisfaction. Self-interest, in all its forms, is a signiﬁcant motivator. Although somewhat negative, it is necessary sometimes to resort to disciplinary procedures to get people to behave in a safe way. This is rather like speed cameras on roads with the potential for ﬁnes and points on your licence.

428

Asbestos based material

asbestos asbestos pipe pipe lagging lagging

Figure 20.3

Asbestos pipe lagging.

Paper 1 – Question 3 (a) Explain why young persons may be at a greater risk from accidents at work. (4) (b) Outline the measures that could be taken to minimize the risks to young employees. (4)

Answer: (a) Young workers have a lack of experience, knowledge and awareness of risks in the workplace. They tend to be subject to peer pressure and behave in a boisterous manner. They are often willing to work hard and want to please their supervisor

Specimen answers to NEBOSH examinations and can become over-enthusiastic. This can lead to the taking of risks without the realization of the consequences. Some younger workers have underdeveloped communication skills and a limited attention span. Their physical strength and capabilities may not be fully developed and so they may be more vulnerable to injury when manually handling equipment and materials. They are also more susceptible to physical agents, biological and chemical agents such as temperature extremes, noise, vibration, radiation and hazardous substances. (b) The Management of Health and Safety at Work Regulations require that a special risk assessment must be made before a young person is employed. This should help to identify the measures which should be taken to minimize the risks to young people. Measures should include: ➤ additional supervision to ensure that they are closely looked after, particularly in the early stages of their employment ➤ induction and other training to help them understand the hazards and risk at their work place ➤ not allowing them to be exposed to extremes of temperature, noise or vibration ➤ not allowing them to be exposed to radiation, or compressed air and diving work ➤ carefully controlling levels of exposure to hazardous materials so that exposure to carcinogens is as near zero as possible and other exposure is below the WEL limits which are set for adults ➤ not allowing them to use highly dangerous machinery like power presses and circular saws; explosives mechanical lifting equipment such as forklift trucks etc. ➤ Restricting the weight that young persons lift manually to well below any weights permitted for adults. There should be clear lines of communication and regular appraisals. A health surveillance programme should also be in place.

20.2.2

NGC2 – Controlling workplace hazards

Paper 2 – Question 1 A glassworks produces covers for streetlights and industrial lighting. The process involves molten glass being blown by hand and shaped in moulds. (i) Identify FOUR health effects that may be caused by working in the hot conditions of the glass factory. (ii) Describe measures that could be taken in order to minimize the health effects of working in such hot environments.

(4)

(6)

(iii) Outline the factors relating to the task and the load that may affect the risk of injury to an employee engaged in stacking the ﬁnished product onto racking.

(10)

Answer: (i) 1. Heat exhaustion due to high ambient temperature 2. Dehydration due to excessive sweating 3. Heart stress and, in extreme cases, heat stroke due to prolonged exposure to high ambient temperatures 4. Burns from handling hot molten glass 5. (Additional answer) the eyes can also be affected by high intensity light from looking at molten glass. (ii) The health effects of working in a hot environment can be reduced by the gradual acclimatization of new workers. Even after the initial acclimatization, frequent rest periods will be necessary to allow the body to acclimatize to the hot conditions on a daily basis. Rest should be in cool areas which in summer may need to be artiﬁcially cooled. If, in addition, the humidity is high, a good supply of ventilation air will be needed, to help control sweating. Adequate supply of cold drinking water is essential to avoid dehydration. Workers in hot conditions should wear appropriate clothes, which must be a compromise between lighter garments to promote evaporation of perspiration, and protective clothes to prevent burns. It will be necessary to provide protective leather or ﬁre resistant aprons and gloves, and appropriate eye and face protection such as eye visors. Visors may need to be supplied with cooling air to keep people cool and permit proper vision. Screens could also be provided to protect workers from radiant heat. Periodic health surveillance should be provided. Finally, workers should be trained to recognise illhealth affects on others. (iii) The task should be analysed in detail so that all aspects of manual handling are covered including the use of mechanical assistance. This will involve a manual handling risk assessment. The number of people involved and personal factors, such as age and health, should also be considered. A satisfactory body posture must be adopted with the feet ﬁrmly on the ground and slightly apart. To avoid work related upper limb disorders (WRULDS) there should be no stooping or twisting of the trunk; it should not be necessary to reach upwards since this will place additional stresses on the arms, back and shoulders. The further the load is held or manipulated from the trunk, the more difﬁcult it is to control and the greater the stress imposed on the

429

Introduction to Health and Safety at Work back. These risk factors are signiﬁcantly increased if several of them are present at the same time. The load should not be carried over excessive distances (greater than 10 m). The frequency of lifting, and the vertical and horizontal distances the load needs to be carried (particularly if it has to be lifted from the ground and/or placed on a high shelf) can lead to fatigue and a greater risk of injury. If the loads are handled whilst the individual is seated, the legs are not used during lifting and stress is placed on the arms and back. There should not be excessive pulling, pushing or sudden movements of the load. The state of ﬂoor surfaces and the footwear of the individual should ensure that slips and trips are avoided. There should be sufﬁcient rest or recovery periods and/or the changing of tasks particularly in the hot ambient temperatures of the glassworks. This enables the body to recover more easily from strenuous activity. The imposition of a high rate of work is a particular problem with some automated production lines and can be addressed by spells on other work away from the line. The handling capability of an individual is approximately halved when he or she becomes a member of a team. Visibility, obstructions and the roughness of the ground must all be considered when team handling takes place. The load must also be carefully considered during the assessment – it may be too heavy. The maximum load that an individual can lift will depend on the capability of the individual and the position of the load relative to the body. There is therefore no safe load but guidance is available from HSE literature, which does give some advice on loading levels. If the load is too bulky or unwieldy, its handling is likely to pose a risk of injury. Visibility around the load is important, as is awareness that it may hit obstructions or become unstable in windy conditions. The position of the centre of gravity is important for stable lifting – it should be as close to the body as possible; however, this may be difﬁcult if the load is hot, such as in boxes or trays of recently blown glass. They should be allowed to cool sufﬁciently. The load becomes difﬁcult to grasp when it is carried over slippery surfaces, has rounded corners or there is a lack of foot room. Sometimes the contents of the load are likely to shift. This is a particular problem when the load is a container full of smaller items, such as small glass covers. These are glass components which may shatter if dropped and leave shards of glass to be carefully cleared up.

430

The load is likely to be hot and could be sharp as well in places or when broken so that personal protective equipment, such as leather gloves and aprons plus eye protection, may be required.

Paper 2 – Question 2 Outline the precautions that may be needed when carrying out repairs to the ﬂat roof of a building. (8)

Answer: Roof work is hazardous and requires a speciﬁc risk assessment and method statement prior to the commencement of work so that the required precautions may be identiﬁed. The particular hazards are fragile roofing materials, including those materials which deteriorate and become more brittle with age and exposure to sunlight, exposed edges, unsafe access equipment and falls. There must be suitable means of access such as scaffolding, ladders and crawling boards. Suitable edge protection will be needed in the form of guard rails to prevent the fall of people or materials, and access must be restricted to the area below the work using visible barriers. Warning signs indicating that the roof is fragile, should be displayed at ground level. Protection should be provided in the form of covers where people work near to fragile materials and roof lights. The means of transporting materials to and from the roof may require netting under the roof and even weather protection. Precautions will be required for other hazards associated with roof work, such as overhead services and obstructions, the use of equipment such as gas cylinders and bitumen boilers and manual handling. Finally, only trained and competent persons must be allowed to work on roofs and they must wear footwear having a good grip. It is good practice to ensure that a person does not work alone on a roof.

Paper 2 – Question 3 For EACH of the following agents, outline the principal health effects AND identify a typical workplace situation in which a person might be exposed: (i) carbon monoxide (2) (ii) asbestos (2) (iii) legionella bacteria (2) (iv) hepatitis virus. (2)

Answer: (i)

Carbon monoxide is a colourless, tasteless and odourless gas. It causes headaches and breathlessness and at higher concentrations unconsciousness and death. The most common occurrence of carbon monoxide is in exhaust gas from a vehicle engine.

Specimen answers to NEBOSH examinations

Figure 20.4

Flat roof

Working in a vehicle repair garage without proper ventilation to exhaust gases would expose a person to carbon monoxide fumes. (ii) Asbestos produces ﬁne ﬁbres which can become lodged in the lungs. This can lead to asbestosis (scaring of the lungs), lung cancer or mesothelioma – cancer of the lining of the lung. Asbestos can be found in buildings, in ceiling tiles and as lagging around heating pipes. When these sites are disturbed, the asbestos ﬁbres become airborne and inhalable affecting those engaged in maintenance or demolition work. (iii) Legionella is an airborne bacterium and is found in a variety of warm water sources between 20 and 45ºC. It produces a form of pneumonia caused by the bacteria penetrating the alveoli in the lungs. The disease is known as Legionnaires’ disease and has symptoms similar to inﬂuenza. The three most common systems at risk from the bacteria are water systems that incorporate a cooling tower, air conditioning units, and showers. People working on these systems or working in the area of infected systems are at risk, particularly if they are over 45 years of age and it affects men more than women. (iv) Hepatitis is a disease of the liver and can cause high temperatures, nausea, jaundice and liver failure. The virus can be transmitted from infected faeces (Hepatitis A) or by infected blood (Hepatitis

B and C). Hospital workers and ﬁrst aiders who come into contact with blood products are at risk of hepatitis.

20.3 NGC3 – The practical application The guide to the NEBOSH National General Certiﬁcate is essential reading for all candidates before they attempt the practical application. The guide contains details on the aims of the application, the rules to be followed, the breadth and depth of observations and management report expected and the marking scheme. In this section, the NEBOSH guide is summarized in section 20.3.1 and a specimen practical application, with associated observations and management report, is given in section 20.3.2.

20.3.1

Requirements of the practical application

The practical application aims to test the application of basic health and safety knowledge to a workplace inspection. The test assesses the understanding of key issues and the ability to communicate the ﬁndings of the inspection in an effective way to a member of the senior management team. The formal aim of the assessment is

431

Introduction to Health and Safety at Work to prove a candidate’s ability to successfully complete two activities: ➤ to carry out unaided a safety inspection of a workplace, identifying the more common hazards, deciding whether they are adequately controlled and, where necessary, suggesting appropriate and cost effective remedial action; and ➤ to prepare a report that persuasively urges management to take appropriate action, explaining why such action is needed (including reference to possible breaches of legislation) and identifying, with due consideration of reasonable practicability, the remedial measures that should be implemented. The inspection should take between 30 and 45 minutes and cover as wide a range of hazards as possible. Observations and comments should be noted on the observation sheets provided by NEBOSH (see Appendix 1 of this chapter). Candidates are expected to recognise actual and potential hazards and good – as well as bad – work practices and welfare provisions. While only brief details of each hazard are required, it is important that the assessor can subsequently identify: ➤ ➤ ➤ ➤

Medium and long-term actions must be noted as well as immediate actions to control any dangerous hazard. The distinction between immediate and longer term action must be clear. The removal of a hazard is an example of immediate action, whereas the provision of information and training is longer term. The proposed remedial actions must not only remove or control the hazard but be realistic and cost-effective and the associated time scales realistic and appropriate. Many candidates confuse comments with actions. The examiner looks for clear action proposals to remedy any observed weakness. The hazard recorded must be speciﬁc so that examples of poor housekeeping are recorded rather than a single statement of ‘poor housekeeping’. For some assessments, issues of employee awareness, supervision, maintenance, inspection and testing procedure may need to be considered. There is always a requirement for a monitoring system even if no action is required for a particular hazard at the time of the inspection. For most practical assessments, the examiner will be looking for between 20 and 30 observations. For the management report, candidates are marked against the following ﬁve criteria: 1.

Selection of topics for urgent management action (0 to 10 marks) This requires candidates to emphasize those items on their observation sheets that they consider require urgent attention by management and to present them, together with suggested remedial actions (both short and longer term), in a logical and coherent manner. Those issues that are high risk and high priority, such as electrical safety, emergency exits and poor work practices, must be emphasized and highlighted. The report must differentiate between urgent and routine matters with simple cross-referencing to the observation sheets.

2.

Consideration of cost implications (0 to 5 marks) Candidates must demonstrate that they are aware of cost implications although they will not be judged on the value of the actual costs of a given measure. If training is recommended as a solution to a problem, candidates should indicate if this is likely to require a few hours of work-based instruction or several days of more costly off-the-job training. It is the assessment of magnitude of the cost that is important, rather than precise ﬁgures. Words, such as ‘cheap’ and ‘expensive’, are better than giving no estimate. There should be an emphasis on the costs of taking no action (e.g. lower productivity, more compensation claims and possible enforcement action).

where the hazard was located the nature of the hazard the degree of risk associated with the hazard the remedial actions, where appropriate, with relevant prioritization.

On completion of the inspection, candidates are allowed about one hour to produce the report, which must normally be in their own handwriting. Candidates are given a summary of the headings under which marks are allocated both for the report and observation sheets. The whole assessment must be carried out under as near examination conditions as possible and should not normally take more than two hours. Candidates are not allowed to use previously prepared or organizational checklists or any other reference material. For the inspection and practical assessment of the workplace, candidates are expected to do more than simply identify physical hazards such as unsafe machinery although this is important. In most workplaces they should ﬁnd examples of chemical, ﬁre, ergonomic, electrical, manual handling, slip, trip and fall (people and objects) hazards. Consideration should also be given to health and physical hazards (e.g. dermatitis, noise and vibrations), access, emergency arrangements and welfare and environmental problems, such as heating or lighting. They need to comment when there is adequate control of hazards and where safe working practices are being observed, as well as when the opposite is the case.

432

Specimen answers to NEBOSH examinations 3.

➤ a short list of issues requiring urgent action by management with convincing arguments why such action is needed and calling attention to possible breaches of health and safety legislation ➤ reference to the list of observations and recommended actions (which should be attached to the report), calling particular attention to any recommendations which could have a high cost in terms of ﬁnance, inconvenience or time ➤ a short conclusion.

Identification of breaches of legislation (0 to 5 marks) Since reference material is not allowed during the application, candidates are only expected to indicate knowledge of the relevant legislation rather than the exact title and date. For example: Health and Safety at Work Act, First-Aid Regulations, PUWER and the Workplace Regulations are acceptable abbreviations on the observation sheets and in the management report. The following list of Acts and Regulations would be relevant to all inspections: ➤ Health and Safety at Work etc. Act ➤ Management of Health and Safety at Work Regulations ➤ Regulatory Reform (Fire Safety) Order ➤ Workplace (Health, Safety and Welfare) Regulations Most inspections would also include some of the following regulations: ➤ Manual Handling Operations Regulations ➤ Provision and Use of Work Equipment Regulations ➤ Personal Protective Equipment at Work Regulations ➤ Electricity at Work Regulations ➤ Control of Substances Hazardous to Health Regulations ➤ Health and Safety (Display Screen Equipment) Regulations ➤ Health and Safety First Aid Regulations ➤ Noise at Work Regulations ➤ Vibration at Work Regulations ➤ Health and Safety (safety signs and signals) Regulations ➤ Work at Height Regulations ➤ Health and Safety Consultation with Employees Regulations.

4.

Presentation of information (0 to 10 marks) A good report should normally comprise about three sides of handwritten A4 (i.e. about 500–750 words). It should cover the following points in a logical sequence:

5.

Effectiveness in convincing management to take action (0 to 15 marks) Managers are unlikely to have time to plough through lengthy reports. The report should be written in such terms that a manager would be able to take reasonable action based on facts relatively quickly. Therefore, it should be concise, readable and highly selective in terms of the action required by management. It should contain balanced arguments on why action is needed and explain the effect it would have on the standards of health and safety at the workplace.

20.3.2

Specimen practical application

The specimen practical assessment took place in a small joinery (woodworking) facility which is situated in a selfcontained building. The facility is used to train 20 carpentry and joinery trainees and produce window frames for use on various building projects. The average age of the trainees is 24 although a minority of them are under 18 years. There are 5 employees – 2 supervisors, 2 technicians and an administrator who administers the training scheme and liaises with the building projects. Within the building are two workshops – a bench and a machine workshop, an administration ofﬁce, welfare facilities, a rest room, two lecture rooms and a store room. The assessment is concerned only with the workshops, the administration ofﬁce and the welfare facilities. The following management report was submitted to the Chief Executive of S & J Joinery Training Workshops.

➤ where and when the inspection took place ➤ a brief summary of what was found

433

Introduction to Health and Safety at Work The management report 1. Introduction This report follows a health and safety inspection of the workshops, the administration ofﬁce and welfare facilities at S & J Joinery Training Workshops. The inspection took place on 7 June 2007. The report’s aim is to highlight good practice and areas of concern requiring urgent action. The observations are listed in Appendix 1 attached to this report. 2. Summary There have been no serious accidents since records began some ﬁve years ago. This good record appears to have led to a relaxation in the monitoring of standards. Several inexpensive improvements in the health and safety management systems are recommended. There are some serious concerns involving ﬁre precautions, the machine shop, manual handling and electrical equipment leading to breaches of the Health and Safety at Work Act (HSWA), the Management of Health and Safety at Work Regulations (MHSWR), the Regulatory Reform (Fire Safety) Order (Fire Regs.), the Provision and Use of Work Equipment Regulations (PUWER), the Personal Protective Equipment at Work Regulations (PPE Regs.), the Electricity at Work Regulations and the Workplace Regulations. Any of these breaches could attract enforcement action from the HSE. All risk assessments must be reviewed as a matter of urgency. A more detailed description of the topics requiring immediate attention is given below with reference to the observation sheets given in brackets. 3. Issues requiring attention a) Management of health and safety Many of the observed weaknesses result from a poor management system which could be improved if the technicians and administrator were given speciﬁc health and safety duties and, if necessary, relevant training of up to half a day duration. At least one member of staff should be trained in ﬁrst aid at a cost of £200 approx. In particular, the dangerous electrical equipment (20 and 25), the inappropriately guarded machines (22 and 23), the PPE problems (11 and 24) and the need to check that all equipment is switched of at the end of the day (35) can be addressed by assigning speciﬁc health and safety duties to staff. Supervisors also need to be more proactive in ensuring that benches are kept tidy (11, 15, 19 and 21) and trainees adhere to health and safety rules (15 and 24). COSHH assessments may need to be revised (19). Many observations indicate that risk assessments, if they have been made, are no longer valid and need to be reviewed urgently. Finally, the MHSWR require a speciﬁc risk assessment to be made for persons under the age of 18 years (1). The total cost of these recommendations will be between £200 and £500. The health and safety committee must assess the quality and contents of the induction course given to trainees because of the large number of hazards found. b) Fire precautions The Fire Regs. require that ﬁre risk assessments, ﬁre ﬁghting arrangements, ﬁre information and ﬁre training be provided at the workshops. Therefore, there is an urgent need to install ‘Fire Exit’ signs (2), ﬁre drills (4) and two ﬁre extinguishers in the machine shop (25). This last point should have been noted by the extinguisher service contractor. The emergency ﬁre exit door should remain unobstructed at all times and unlocked whenever the building is in use (3). Security could be improved by ﬁtting an alarm system which is activated whenever the door is opened or by the use of a quick release mechanism. The total cost of all these improvements should not exceed £300. The ﬁre risk assessment must be reviewed. c) The machine shop There are serious concerns regarding the guarding of the jig saw and the circular saw (22 and 23). The operation of these machines must cease immediately until they are properly guarded. The local exhaust ventilation (LEV) system must be examined and maintained on a regular basis with records being kept as required by PUWER and

434

Specimen answers to NEBOSH examinations the broom (27) replaced by an industrial grade vacuum cleaner (approximately £200). Wood dust causes health problems which can be very serious. The rules concerning the use of the machines by trainees are commendable. d) Manual handling concerns A mechanical lift truck should be purchased and used for the movement of window frames and timber (7). A manually operated truck should be sufﬁcient at about £200 and much cheaper than a fork lift truck with its considerable training costs. Manual handling and trip hazards could be eased considerably by the erection of suitable shelving on the walls of the two workshops. Only one day’s supply of timber should be kept in the workshops. Any excess timber stocks should remain in the store-room. The use of shelving is a very cheap option (£50). e) Other issues The PPE Regulations require that all personal protective equipment must be properly maintained and stored (11). The heating system should be checked by a competent person because the workshops felt cold on the day of the inspection (below 16ºC – the minimum recommended by the Workplace Regs. Code of Practice) and there was an electric ﬁre in the administration ofﬁce (29). An improvement in housekeeping would ensure that ﬂoors and benches are kept clear and unobstructed. 4. Conclusions The workshops were found to be clean, well maintained and well lit. The trainees clearly enjoyed working there. There were, however, a number of issues which need to be addressed urgently to avoid possible legal action or compensation claims following injuries. All these problems, other than the heating system, should be rectiﬁable within a total cost range of £ 1000–£1500. Finally, the Health and Safety policy should be revisited and prominently displayed in both workshops.

Signed...J Brown.........

Date...7 June 2007...

Enclosures: Appendix 20.1 The practical assessment

435

Introduction to Health and Safety at Work Appendix 20.1

The Practical Assessment

NATIONAL GENERAL CERTIFICATE

Candidate’s observation sheet

Unit NGC3 – Health and safety practical application Candidate name Place inspected

Sheet number

of

6

Candidate number C 9887

J Brown S & J Joinery Training Workshops

Observations List hazards, unsafe practices and good practices

1

Priority/risk (H, M, L)

Date of inspection 7 / 6 / 2007

Actions to be taken (if any) List all immediate and longer-term actions required

Time scale (immediate, 1 week, etc)

Complete speciﬁc risk assessment for young persons. Establish a review timetable for all risk and COSHH assessments. Discuss all risk assessments at the Health and Safety committee meeting.

Immediate

Inform employees and trainees of ﬁre escape routes. Obtain and install ﬁre exit signs and review ﬁre risk assessment. Organise some basic ﬁre training.

Immediate

GENERAL OBSERVATIONS 1. Several risk and COSHH assessments have been completed but the special risk assessment required by the Management Regs. for young workers has not been done.

2. No Fire Exit signs are posted in the building. (Fire Regs)

3. Emergency exit door is locked to protect building against unauthorised entry. Also the door was obstructed by several lengths of timber. (Fire Regs)

4. No ﬁre drills have been undertaken for some time. (Fire Regs)

M .

H

H .

H

436

–

Each year

1 week 1 month

Remove timber and any other obstacles and unlock door. Look for an alternative security arrangement and install. Monitor doors regularly and include this problem in the ﬁre training.

Immediate

Undertake an immediate trial evacuation of the building to designated assembly point. Arrange 1 ﬁre drill for all new trainees.

1 week

Arrange at least 2 ﬁre drills for employees per year and record evacuation time. 5. All electrical equipment, other than electric ﬁre in the ofﬁce and the sander in the workshop (see later), has been PAT tested.

1 month

Arrange for the ﬁre and the sander to be PAT tested when repairs completed. All hand-held tools should be checked each week and PAT tested very 6 months. Ensure that records are kept and equipment re-tested at regular intervals.

1 month Monthly

1 week after enrolment 6 months

1 week after repairs. Weekly 6 months Each year

Specimen answers to NEBOSH examinations

NATIONAL GENERAL CERTIFICATE

Candidate’s observation sheet

Unit NGC3 – Health and safety practical application

Sheet number

2

of

Candidate name

J Brown

Candidate number C 9887

Place inspected

S & J Joinery Training Workshops

Date of inspection 7 / 6 / 2007

Observations List hazards, unsafe practices and good practices

Priority/risk (H, M, L)

6

Actions to be taken (if any) List all immediate and longer-term actions required

Time scale (immediate, 1 week, etc)

Fix covers over cables and re-route away from busy walkways. Reorganise workshop layout and/or work activities to reduce risk of tripping. Install additional power sockets to reduce the need for long trailing cables.

Immediate

Stack all unused timber in corner of workshop or adjacent free room. Fix up suitable shelving to store timber safely. Only store a day’s requirement in the workshops. Include this arrangement in future training and monitor. Decide on a future strategy for timber storage and implement.

Immediate

GENERAL OBSERVATIONS (Cont) 6. Risk of slips, trips and falls due to trailing cables in both workshops. (Electricity Regs.)

7. Timber left lying on ﬂoor of both workshops – slip hazard.

8. Risk of back injuries from lifting heavy lengths of timber and manufactured window frames. (Manual Handling Regs.)

9. First aid box is fully and properly stocked and appropriate notices displayed in each workshop. (First Aid Regs.) 10. No trained ﬁrst aider in the building. If required, help is obtained from next building.

H

H

H

1 week 6 months

2 weeks

6 months

Ensure that timber lengths are always lifted by at least 2 persons and window frames by 4 persons. Undertake a manual handling risk assessment to see whether mechanical assistance can be used. Give everyone a basic manual handling training course including supervisors. Monitor activities regularly.

Immediate

L

No action required other than monitoring the contents of the ﬁrst aid box to ensure that it is reﬁlled.

Each week.

M

Arrange for at least 1 member of staff (preferably 2) to be trained as a ﬁrst aider.

3 months

2 weeks 1 month Every 3 months

437

Introduction to Health and Safety at Work

NATIONAL GENERAL CERTIFICATE

Candidate’s observation sheet

Unit NGC3 – Health and safety practical application

Sheet number

3

of

Candidate name

J Brown

Candidate number C 9887

Place inspected

S & J Joinery Training Workshops

Date of inspection 7 / 6 / 2007

Observations List hazards, unsafe practices and good practices

Priority/risk (H, M, L)

6

Actions to be taken (if any) List all immediate and longer-term actions required

Time scale (immediate, 1 week, etc)

Replace gloves and glasses. Ensure that all PPE is properly stored and maintained. Prominent notices should be displayed and all infringements recorded. Review all PPE risk assessments and monitor. Ensure that trainees receive instruction on the correct use of PPE.

Immediate 1 month

GENERAL OBSERVATIONS (Cont) 11. There several cases of torn gloves and scratched safety glasses on the benches in the 2 workshops. (PPE Regs.)

H

1 month At induction

12. HSW Act poster and several other useful posters on manual handling, noise and the correct use of tools and machines, displayed in both workshops.

–

This is to be commended. May need updating in the longer term.

13. Lighting levels throughout were good.

L

No action required but keep under review.

14. Toilet and washing facilities were satisfactory and cleaned on a regular basis. Barrier cream was provided and trainees instructed to use it. 1 toilet door lock was broken. (Workplace Regs.)

L

Repair toilet door lock. Monitor cleanliness of toilets.

Immediate Daily.

15. Despite several notices forbidding the consumption of food and drink, several trainees had bottles of drinking water on their work benches. (Workplace Regs).

M

Supervisors must enforce ban on food and drink. Install a fresh drinking water facility in the trainee rest room with cups provided.

Immediate

16. Heating levels were low throughout the building and the workshops were cold. (Workplace Regs.)

M

17. All ﬁre extinguishers regularly serviced.

438

–

Check all room temperatures. Have boiler and heating system checked and, if necessary, provide auxiliary heating. Monitor to ensure that a reasonable temperature is maintained. This could be a costly problem in terms of ﬁnance, time and inconvenience. Commendable.

1 month

Immediate 1 week Weekly from Sept to March

Specimen answers to NEBOSH examinations

NATIONAL GENERAL CERTIFICATE

Candidate’s observation sheet

Unit NGC3 – Health and safety practical application

Sheet number

4

of

Candidate name

J Brown

Candidate number C 9887

Place inspected

S & J Joinery Training Workshops

Date of inspection 7 / 6 / 2007

Observations List hazards, unsafe practices and good practices

Priority/risk (H, M, L)

6

Actions to be taken (if any) List all immediate and longer-term actions required

Time scale (immediate, 1 week, etc)

Inform staff and trainees to keep all cupboards shut and post appropriate notice on notice board. Monitor compliance.

Immediate

Identify and label the jar or dispose of it. If it is identiﬁed, ensure that a COSHH assessment has been completed. Supervisor to inform trainees of the unsafe practice. Ensure that the use of hazardous substances is covered during induction training.

Immediate Immediate

Each induction

BENCH WORKSHOP 18. Several cupboard doors under the benches were left open leading to risk of minor injury.

L

19. There was an unmarked jar containing a liquid (solvent?) on one of the benches. (COSHH)

H

On-going

Immediate

20. Frayed lead to hand-held sander – risk of electric shock. (Electricity Regs.)

H

Remove from use. Replace lead, PAT test sander and place it on the PAT register. Include in regular PAT inspection schedule. Include electrical hazards and precautions in induction training for trainees

Immediate 1/2 weeks Every 3 months Each induction

21. Chisels and a Stanley knife left on benches. (PUWER)

H

Remove from benches and place in tool rack. Check to ascertain whether Stanley knife necessary. If it is, use one with a retractable blade. Report ﬁnding to supervisors and inform trainees of dangers. Monitor.

Immediate

On-going

439

Introduction to Health and Safety at Work

NATIONAL GENERAL CERTIFICATE

Candidate’s observation sheet

Unit NGC3 – Health and safety practical application

Sheet number

5

of

Candidate name

J Brown

Candidate number C 9887

Place inspected

S & J Joinery Training Workshops

Date of inspection 7 / 6 / 2007

Observations List hazards, unsafe practices and good practices

Priority/risk (H, M, L)

6

Actions to be taken (if any) List all immediate and longer-term actions required

Time scale (immediate, 1 week, etc)

MACHINE WORKSHOP 22. Jig saw unguarded – guard has been removed. (PUWER)

H

Prohibit use of machine until guard installed. Monitor future use of jig saw. Include need for correct guards on machines in trainee training sessions.

Immediate On-going Each induction

23. Top guard on circular saw set too high. (PUWER)

H

Inform supervisor of dangerous hazard. Set guard to correct gap. Ensure that inspection of all machine guards is part of maintenance schedule and monitor compliance.

Immediate Immediate Each week

24. Noise assessment has been done but several persons not wearing ear defenders even though noise levels are in excess of the upper exposure action level and mandatory signs are in place. (Noise Regs.)

H

Noise assessments are made every year and available in the machine shop. This is commendable. All persons in the machine shop must wear ear defenders when any machine is running. Include this in the trainee induction training.

25. Only a water ﬁre extinguisher available in the machine shop. All machines are electrically powered.

H

26. LEV not been inspected for 3 years. Possible reasons for dust?

H

27. Only a broom available for sweeping up excess wood dust. Inhalation hazard.

H

28. Only trainees over the age of 18 years are allowed to use the machines and then only with close supervision.

L

440

Replace with 2 ﬁre extinguishers – a carbon dioxide and a powder one. Investigate the reasons for this occurrence with the servicing contractor. Again review ﬁre risk assessment. Arrange for immediate inspection by a competent person. Set up an on-going contract for future inspections. Train staff and monitor compliance. Remove broom and replace with an industrial grade vacuum cleaner. Check efﬁciency of LEV (see 26 above). Train and monitor. Commendable.

Immediate Each induction Immediate 3 months 1 week Immediate 3 months

Immediate 3 months

Specimen answers to NEBOSH examinations

NATIONAL GENERAL CERTIFICATE

Candidate’s observation sheet

Unit NGC3 – Health and safety practical application

Sheet number

6

of

Candidate name

J Brown

Candidate number C 9887

Place inspected

S & J Joinery Training Workshops

Date of inspection 7 / 6 / 2007

Observations List hazards, unsafe practices and good practices

Priority/risk (H, M, L)

6

Actions to be taken (if any) List all immediate and longer-term actions required

Time scale (immediate, 1 week, etc)

Remove ﬁre and ﬁt a guard and undertake a PAT test. Place ﬁre on PAT register if it is to be kept and monitor.

Immediate

ADMINISTRATION OFFICE 29. Electric ﬁre in the ofﬁce has no guard and is not included on PAT register. (Electricity Regs.)

H

30. Health and safety policy statement completed but kept in ofﬁce drawer unsigned and undated. (HASW Act)

–

Display policy statement on the main notice board in the workshops and communicate effectively to staff and trainees (at induction) after it has been signed by the chief executive of the company and dated.

31. Employers’ liability insurance certiﬁcate is up-to-date but not displayed on a notice board.

–

Display the Employers’ liability insurance certiﬁcate on the main notice board in the workshops.

32. The accident records are kept up-to-date with no serious accidents reported.

–

Commendable.

33. All trainees and employees are given an induction training session that includes health and safety. Detailed records are kept of this and all other training.

–

This is commendable but given some of the problems found during this inspection, a review of the contents of the induction training should be undertaken.

34. DSE assessment completed even though VDU only used for limited times. (DSE Regs.)

L

Good.

35. Risk of ﬁre due to VDU being left on all the time.

M

Inform staff of the need to ensure that all power supplies to equipment are turned off when the equipment is not in use. Arrange a rota of staff to check all equipment at the end of the day.

After remedial action. Immediate

Immediate 1 week.

441

This page intentionally left blank

Index

Abrasion hazards 131–2, 168, 172 Absolute liability 7–8 Access control 272 Access equipment height working 292–6 Accident books 121 Accidents 2 see also incidents categories 70 costs 18 definition 69 incident rate 50 investigations 117–18 rates 16–17 Accommodation, clothing 258 ACOP see Approved Code of Practice Action, incidents/accidents investigations 117 Acts, summary 308–9 Advantages, portable electrical appliance testing 199–200 Advisers, health and safety 34–5 Agricultural machines, safeguards 179, 180–1 Air pollution 244–5 Air receivers, examination 163 Alarms, security equipment 272 Alcohol: abuse investigation 273 effects 273 Alpha particles 266 Ammonia 229 Appointed persons, first-aid 95 Approved Code of Practice (ACOP) 10–11 Arcing electric 192 Area inspection checklist 114–15 Asbestos 230 Asbestos (Licensing) Regulations 1983 (amended 1998) 312 Assembly and roll call, emergencies 93

Assessments: see also risk assessments exposure 85–6 health surveillance 85–6 safe systems of work 87 Audit: health and safety management system 412–13 performance 109–11 Basic elements, management systems 405–6 BATNEEC see Best Available Techniques not Entailing Excessive Cost Benchmark standard, auditing 110 Benefits, incidents/accidents investigations 117–18 Best Available Techniques not Entailing Excessive Cost 313, 315 Best Practicable Environmental Option 245 Best practice guidance 11 Beta particles 226 Biological agents 224 Biological health hazards 223–246 Boiler examinations 163 BPEO see Best Practicable Environmental Option Breathing apparatus 239,240 Brush cutter/strimmer hazards 172 Building, fire protection 217–219 Burns 189, 190 Buying equipment 37–8 Carbon dioxide 229–30 Carbon monoxide 230 Cardiovascular system 227–8 Carrying employees, mobile work equipment 169–71

Case law see civil law; common law; criminal law; Regulations CDM see Construction Design and Management CDM Regulations, definition 286 CE markings 159, 160, 388–9 Cement dust 284 wet cement 284 Cement mixer safeguards 183–4 Cement/concrete mixer hazards 173 Certificate of conformity 160 Changing facilities 258 Checklist: area inspection 114–15 hazards 76–7 Health and Safety Policy 28–30 manual handling of load assessment 156–8 organization 28 plant 29 policy 28 scaffolding faults 302 Chemical Agents, types 223–4 Chemical health hazards 223–46 Chemicals (Hazard Information and Packaging for Supply) Regulations 2002 37, 320–4 Chlorine 229 CHSW see Construction (Health Safety and Welfare) (CHSW) Regulations 1996 Circular saw hazards 173 Civil law 3–4, 5 Closed circuit television 272 Codes of Practice, ACOP 10–11 Collisions: pedestrians and flying objects 131–2 pedestrians and moving vehicles 131, 133 pedestrians and stationary objects 133–4

443

Index Colour codes, safety signs 384–5 Commercial stakeholders 65 Commitment, management 58, 62–3 Common law 5–6 torts and duties 6–7 Communication: effective 60, 63 lines 31 safe systems of work 82 Company car driver rules 141 Comparison with relevant standards, incident investigation 121 Compensation: accidents/incidents 124–5 claims 128–9 Competence definition 59 Competent persons 33–4 Conduction of heat 206–7 Confined spaces 90 Confined Spaces Regulations 1997 324–6 Conformity certificates 160 Construction activities: hazards and control 278–98 management 285–91 Construction (Design and Management) (CDM) Regulations 1994/2007 296–300, 279, 326–337 Construction guards 185 Construction (Head Protection) Regulations 1989 281, 337–8 Construction (Health Safety and Welfare) (CHSW) Regulations 1996 332, 338–9 Construction industry scope 278–9 Continual improvement systems 413 Contractors 38–42 authorization 40–1 rules observance 41–2 safety rules 41 selection and control 40, 290–1 Control: see also risk control biological health hazards 223–46 chemical health hazards 223–46 construction activities 278–98 contractors 290–1 COSHH measures 236–42 electrical hazards 187–200 excavations 297–8 fire hazards 201–21 health risks 84–6 manual handling hazards 143–55 mechanical handling hazards 143–55 organization 31–2 physical health hazards 250–74 psychological health hazards 250–74 risks 72–3 work equipment 159–85 working above ground level 291–2 Control of Asbestos at Work Regulations 2002 398–9 Control hierarchy, COSHH Regulations 85 Control of Lead at Work Regulations 2002 400

444

Control measures for electrical hazards 194–5 Control of Pesticides Regulations 1986 401 Control of Pollution (Oil Storage) Regulations 245 Control of risks 80–97 Control strategies, vehicle operation 136–7 Control of Substances Hazardous to Health Regulations (COSHH) 2002/2005 37, 339–42 assessments 232–6 principles of good practice 236, 341 requirements 232 role 225 Control of Substances Hazardous to Health Regulations (COSHH) control hierarchy 85 control measures 236–42 principles of good practice 341 Control of Vibration at Work Regulations 2005 389–91 Convection of heat 206 Conveyors 149–50 Cooperation, workforce 42–3 COSHH see Control of Substances Hazardous to Health Regulations Courts 4–5 Cranes 52–3 Criminal law 4 Crushing hazards 168 Culture: development 58–9 effective communication 60 promotion of positive health and safety 49–65 Customer information 37 Cutting hazards 168 Cylinder mower 172, 179 Dangerous occurrence definition 2–3, 69 Dangerous substances: fire hazards 212–14 packaging 322 risk assessment regulations 343 Dangerous Substances and Explosive Atmospheres Regulations (DSEAR) 2002 342–5 Definitions, basic 1–3, 68–9 Demolition hazards and control 281–2 Development, safe systems 187–8 Direct burning, fire spread 207 Directors responsibilities 32–3 Disabled people, fire procedures 220–1 Disease rates 17 Display screen equipment (DSE) 256–8 Display Screen Equipment Regulations 1992 345–7 Document shredders: machinery hazards 171–2 safeguards 178 Documentation, safe systems of work 88 Doors, means of escape from fire 215–16

Drawing-in hazards 168 Drinking water 258 Drivers: distance 141 ergonomic considerations 140 fitness and health 140 risk evaluation 139–41 route planning 140 safety equipment 140 scheduling 140 suitability of vehicle 140 time 140–1 training 139–40 vehicle condition 140 weather conditions 141 Drowning prevention 282 Drug abuse investigation 273–4 Drug effects 273–4 DSE see Display screen equipment DSEAR see Dangerous Substances and Explosive Atmospheres Regulations 2002 Duties: see also responsibilities common law 5–6 Duty of care 7 Duty holders, responsibilities 287–90 Earmuffs 265 Earplugs 265 Ears: human 260 protection 264–5 Eating facilities 258 Economics 64–5 Ejection hazards 168 Electric arcing 192 Electric burns 189–90 treatment 190 Electric shock 189 treatment 190 Electrical equipment: selection 195–6 suitability 195–6 Electrical explosions 190–2 Electrical fires 190–2 Electrical hazards 187–200 general control measures 194–5 inspection strategies 197 maintenance strategies 192 protective systems 195–6 Electrical (Safety) Regulations 1994 400 Electricity: construction hazards and control 284 definitions 188–9 injuries 189–94 inspection strategies 197 maintenance strategies 197 principles 187–8 static 192–3 Electricity at Work Regulations 1989 347–9 Elevators 149–50 Emergencies: assembly and roll call 93 chemical and biological hazards 243

Index procedures 92–4 supervisors 93 Emergency planning, fire 220 Employees: duties HSW Act 13 representation 63 responsibilities 32 Employers: duties 7, 14 responsibilities 32 Employers Liability (Compulsory Insurance) Act 1969 and Regulations 1998 349–51 Enforcement, HSW act 12–14 Engineering controls: COSHH regulations 237–8 design 82 England and Wales, legal system 4–5 Entanglement hazards 168 Environment Agency 15 Environmental considerations chemical and biological hazards 244–6 Environmental Protection Act 1990 312–20 Environmental protection definition 2 Equipment: operating environment 163–4 specific risks 161 working environment 163–4 Ergonomics: ill-health effects 251–4 task design 250–8 workstation design 250–8 Errors, human 56–7 Escape routes, fire 216 Escape times, fire 216–17 EU see European Union European Courts 5 European Union (EU) directives 9 influence of 8–9 Evaluation, risk levels 71–2 Examination: air receivers 163 boilers 163 lifting equipment 154–5 Excavations 297–8 construction hazards and control 282 precautions 297–8 Exceptional violations 58 Expectant mothers, risk assessment 74 Explosions, electrical 190–2 Exposure assessments 85–6 External agencies 14–15 External influences 63–5 Eye protection 242 Falling: from height 132–3, 280 protection against 280 Falling object protective structures (FOPS) 170 Falling objects, protection against 281

Falls: from height 132–3, 280, 281 slips and trips 132 Fault and no-fault compensation 416 Files, health and safety 290 Financial arguments 18–19 Fines see penalties Fire: alarm testing 94 authority 14–15 basic principles 204–5 classification 206 common causes 208–9 compartmentation 218–19 construction hazards and control 283–4 detection 214–15 drills 94 electrical 190–2 emergency planning 220 extinguishers 219–20 hazards and control 201–21 location at risk 210 means of escape 215–17 notices 93, 93–4, 99 people with a disability 220–1 persons at risk 210 risk assessment 209–12 findings 211 maintenance 212 monitoring and reviewing 211 plans 211 refurbishment 212 structural features 211 risk reduction 210–11 routines 93 RRFSO: enforcement 204 offences 204 safety duties 203–4 training staff 220 warning 214–15 Fire fighting equipment maintenance 220 provision 219–20 Fire hazards: dangerous substances 212–4 identification 209–10 Fire precautions (Workplace) regulations 1999 201 Fire protection: buildings 217–19 load of building 217 Fire spread principles 206–8 First Aid Regulations 1981 358 First aider 95–36 First-aid 94–7 appointed persons 95 arrangements 96 box 95 contents 95 personnel numbers 96 Flying object hazards 133 Follow-up, incident investigation 121 FOPS see Falling object protective structures

Fork lift trucks 150–2, 170–1 Forms: incident investigations 121 injury reports 126–7 inspection report, construction site 300–1 job safety analysis 100 manual handling risk assessment 156–8 safety method statement 78 Framework, management 19–2 Frequency, Portable electrical appliance testing 198, 199 Fuel sources, fires 205 Gamma rays 266 Gas Appliances (Safety) Regulations 1992 400 Gas safety (Installation and Use) Regulations 1998 400 Global adverse events, work related 403 Grinder safeguards 178 Guards: adjustable 174–5 construction 185 fixed 174 interlocking 175, 176 machinery 173–5, 176 Guidance: best practice 11 legal 11 Hand protection 241–2 Hand-arm vibration syndrome (HAVS) 252 Hand-held tools, work equipment 164–7 HAVS see Hand-arm vibration syndrome Hazard definition 3 Hazardous substances, classification and health risks 224–5 Hazardous Waste Regulations 246, 341 Hazards: checklist 76–7 construction activities 278–98 definition 69 elimination 81 excavations 297–8 fire 201–21 heat and radiation 265–8 identification 71 machinery 171–3 manual handling 143–55 mechanical handling 143–55 mechanical machinery 167–9 mobile work equipment 169–71 movement of people and vehicles 130–41 non-mechanical machinery 171 pedestrians 130–2 reduced time exposure 82 substitution 81–2 vehicle operations 135–6 work equipment 159–85 working above ground level 291–2

445

Index Health definition 1 Health hazards: biological 223–46 chemical 223–46 construction hazards and control 284–5 specific agents 228–32 survey techniques 235–6 Health risks 70 control 84–6 survey techniques 235–6 Health and Safety at Work Act 1974 (HSW Act) 9–14, 38–9, 307, 309–12 overview 10–11 Health and Safety Commission (HSC) 10, 14, 307–8, 311–12 Health and Safety (Consultation with Employees) Regulations 1996 43, 338–9 Health and safety culture 49–65 Health and Safety (Display Screen Equipment) Regulations 1992 345–7 Health and safety file, management of construction activities 287 Health and Safety File Regulations 332 Health and Safety (First Aid) Regulations 1981 358 Health and Safety (Information for Employees) Regulations 1989 358–9 Health and safety management systems basic elements 405–6 benefits and problems 414–15 international 405–11 involvement of stakeholders 411–12 Health and safety plan, of construction activities 287 Health and safety policy, checklist 28–30 Health and safety rules, company car drivers 141 Health and Safety (Safety Signs and Signals) Regulations 1996 384–6 Health and safety standards, promotion 58–9 Health surveillance 242–3 Heat, transmission principles 206–8 Heat hazards 265–8 Height working 291–7 construction hazards and control 279–80 Heinrich’s accidents/incidents ratio 51 Hierarchy, risk control 81–4 High voltage apparatus, work permit 91 Highway Code 141 Hoists 153, 154 Hold-to-run control 176–7 Hot work, permit 91 Housekeeping, risk control 82 HSC see Health and Safety Commission

446

HSG 65, international health and safety management system 406–7 HSW Act see Health and Safety at Work Act Human body, routes of entry 225–7 Human errors 56–7 ICC see Incident Contact Centre Ignition sources 205 Ill-health effects of poor ergonomics 251–4 ILO-OSH 2001, international health and safety management system 409–11 Incident Contact Centre (ICC) 123 Incidents: causes 118–21 data analysis/collection 123–4 investigation 118–21 recording and reporting 121–3 legal recording and reporting requirements 121–3 Incidents/accidents, reasons for investigation 117–18 Individual capability, manual handling assessment 147–8 Induction training 61 Information: customers 37 risk control 75–82 work equipment hazards and control 161 Information for Employees Regulations 1989, 358–9 Information gathering, review and audit 110 Infra-red radiation 268 Injuries: see also accidents accident investigation 118 electricity 189–94 manual handling 143–4 report forms 126–7 risk reduction 146–8 Inspections: construction site, report 298 electricity, strategies 197 equipment for work at height 296 excavations 297–8 frequency 107, 198 hand tools 165 lifting equipment 154 proactive monitoring and measuring performance 105–7 Provision and Use of Work Equipment Regulations 1998 162–3 reports 106 standards 106–7 work equipment hazards and control 162–3 Inspectors powers: enforcement 12–13 HSW Act 311

Instruction, work equipment hazards and control 161 Insulating materials 218 Insurance: accidents/incidents 124–5, 128–9 claims 128–9 companies 15 Internal influences 62–3 International aspects, health and safety 402–16 International health and safety management system: HSG 65, 406–7 ILO-OSH 2001 409–11 OHSAS 18001 407–9 Interview techniques 120 Investigations: alcohol problems 273 drug problems 273–4 incidents 118–21 forms 121 interview techniques 120 Ionising radiation 226–7 Ionising Radiation Regulations 1999 360–2 Isocyanates 230 Job safety analysis form 100 Job training 61–2 Ladders 292–3 Lasers 267–8 Lead 230–1 Legal arguments 17–18 Legal framework 3–4 Legal guidance 11 Legal reasons, incidents/accidents investigations 117 Legal requirements: safe systems of work 87 summary 307–401 Legal system: England and Wales 4–5 Scotland 5 Legionella 231 Legislation enforcement 64 Leptospirosis 231 Liability, statutory levels 7–8 Licences, waste management 317–9 Lifting equipment: cranes 152–3 fork lift trucks 150–2 safe use 148 statutory examination 154–5 types 149–53 Lifting Operations and Lifting Equipment Regulations 1998 (amended 2002) 362–5 Lifting tackle, cranes 153 Lifts 153 see also hoists Lighting: means of escape from fire 216 workplace environment 258–9

Index Limitations, portable electrical appliance testing 200 Load, manual handling assessment 145–6 Lone workers: risk assessment 75 safe systems 87 Machinery: hazards 171–3 safeguards 173–5 Maintenance: chemical and biological hazards 243 electricity, strategies 197 equipment with specific risks 161 equipment for work at height 296–7 fire fighting equipment 219–20 work equipment hazards and control 162 Management: commitment 58, 62–3 construction activities 285–91 framework 19–21 HSW Regulations 1999, 14 occupational road safety 137–41 organizing for HSW 31–43 road safety, benefits 138 training 62 vehicle movements 137 Management of Health and Safety at Work Regulations (MHSW) 1999 14, 80, 307, 365–7 Manager responsibilities 44–5 Manual handling: checklist 156–8 hazards 143–55 hierarchy of measures 144–5 injuries 143–4 loads 156–8 risk assessment 144–8 risk assessment forms 156–8 training 148 Manual Handling Operations Regulations (MHO) 1992 (amended 2002) 307–9 MDF, see wood dust Measuring failure, reactive monitoring 105 Measuring performance, observation techniques 106 Mechanical handling: equipment types 149–53 hazards 143–55 Mechanical machinery, hazards 167–9 MEL see Maximum exposure limit MHSW see Management of Health and Safety at Work Microwaves 268 Mistakes, human errors 56 Mobile elevated work platforms 296 Mobile phones, security equipment 272 Mobile scaffold towers 295 Mobile work equipment 169–71

Monitoring: risk control 73 safe systems 89 Monitoring performance frequency 107 responsibility 107 review and audit 109 Moral arguments 16–17 Musculoskeletal problems 257 Near miss, definition 2, 69, 117 Negligence 6–7 Nervous system 227 Noise: action levels 262–3 assessments 261–3 construction hazards and control 279 control techniques 263–4 health effects 260–1 physical and psychological hazards and control 259–65 Noise at Work Regulations1989 259 Non-ionising radiation 267–8 Non-mechanical machinery hazards 171 Nursing mothers, risk assessment 74 Objectives, risk assessment 70 Observation techniques, measuring performance 106 Occupational ill-health, definition 70 Occupational road safety, management 137–41 Occupational/work-related ill health 2, 69 Occupiers Liability Acts 1957 and 1984 400–1 OEL see Occupational exposure limits OES see Occupational Exposure Standard OHSAS 18001 international health and safety management system 407–9 Operating environment, equipment 163–4 Organic solvent hazards 229 Organization 31–43 control 31–2 policy 25–6 responsibilities 32–3 Oxygen, fire hazards 205 Pedestal drill hazards 172 Pedestrian hazards 132–5 control strategies 132–4 preventative measures 132–5 Pedestrians: collisions with flying objects 133 collisions with moving vehicles 133 collisions with stationary objects 133–4 Penalties, health and safety offences 13, 312 Performance: audit and review 109–11

measurement 102–7 reason for measurement 103 Performance assessment phase 406 Performance improvement phase 406 Permits to work 89–92 principles 90 types 90–1 Personal hygiene 243 Personal Protective Equipment at Work Regulations 1992 (amended 2002) 374–6 Personal protective equipment (PPE) COSHH regulations 238–42 risk control 83 Persons at risk 71 Persons in control of premises 35 Photocopiers: machinery hazards 171 safeguards 177–8 Physical health hazards 250–74 Planning phase, health and safety management systems 406 Plant checklist 29 Policy 23–30 arrangements 26 checklist 28–30 key elements 24–6 review 26–7 statement 24–5 Pollution Prevention and Control Act 244, 313 Portable electrical appliance testing 197–200 Portable electrical equipment 193–4 Positive health and safety culture 411–12 Power tools, hand-held 165–7 PPE see Personal protective equipment Practicable, definition 8 Precautions, excavations 297–8 Premises: control 35 joint occupation 42 persons in control 35 Preparation, safe systems 88 Pressure Systems Safety Regulations 2000 (PSSR) 401 Preventative measures: COSHH Regulations 236 ergonomic risks 253–4 pedestrian hazards 134–5 Prevention: risks 80–1 workplace stress 269–70 Proactive monitoring 102, 105 Procedures, permits to work 89–90 Production demands 62 Promotion, health and safety standards 58–9 Protection strategies, radiation 268 Protective clothing 182, 242 Protective systems, electrical equipment 195–6

447

Index Provision and Use of Work Equipment Regulations 1998 (PUWER) 128, 159, 362, 376–80 Psychological health hazards 250–77 Psychological problems, display screen equipment 256–8 Purchase of equipment, risk 37–8 PUWER see Provision and Use of Work Equipment Regulations 1998 Radiation: hazards 265–8 heat transmission 207 protection strategies 268 Radios and pagers 272 Reactive monitoring 102 incidents 116 measuring failure 105 Reasonably practicable, definition 8 Recommendations for action, incident investigation 121 Records: Portable electrical appliance testing 197 risk assessment 73, 77 Regulations: alphabetical list 308–9 chronological list 309 Regulatory authorities: role 414 safety management systems 414 Regulatory Reform (Fire Safety) Order 2004 (RRFSO) 202–4 Regulatory Reform (Fire Safety) Order 2005 (RRFSO) 351–8 Repetitive strain injury (RSI) (tenosynovitis) 251 Report forms, construction site inspection 300–1 Report writing, monitoring 107–9 Reporting of Injuries Diseases and Dangerous Occurrences Regulations 1995 (RIDDOR) 122–3, 380–3 Reports, excavations 298 Resistance of structural elements, fire protection 218 Respiratory protection equipment 239–41 Respiratory system 226–7 Responsibilities: duty holders 287–8, 289 employees 32 employers 32 managers 44 work permits 91 Rest facilities 393 Retail checkout conveyor machinery hazards 173 safeguards 183 Retail compactor: machinery hazards 173 safeguards 182–3

448

Review: performance 111 risk control 84 RIDDOR see Reporting of Injuries Diseases and Dangerous Occurrences Regulations 1995 Risk: control principles 80–97 definition 3, 67 evaluation 71–2, 139–41 purchase of equipment 37–8 Risk assessment 67–9, 212, 325 definitions 68–9 examples 112–4 fire 209–12 legal aspects 67–8 level evaluation 71–2 management 70–1 manual handling 144–8 monitoring and review 73 objectives 70 process 71–3 records 73, 77–9 Regulations confined spaces 324–6 dangerous substances 212 legal requirement 307 special cases 73–5 types 68 Risk control hierarchy 72–3, 81–4 measures 72 performance measurement 104–5 prioritization 73 Risk reduction, injuries 146–8 Road safety management 137–41 Rollover protective structures (ROPS) 169 Roofs, fragile 280 ROPS see Rollover protective structures Routine violation 57 RRFSO see Regulatory Reform (Fire Safety) Order 2004 RSI see Repetitive strain injury Rules, contractors safety 41 Safe driving: lift trucks 152 mobile work equipment 171 Safe place of work, construction hazards and control 279 Safe systems of work 86–9 definition 86 Safeguards, machinery 173–5 Safety: contractor rules 41 culture 49–50 definition 2 devices 176–7 hooks 153, 154 method statement form 100 performance 50–1 Safety Committees Regulations 1977 42–3

Safety Representatives Regulations 1977 42–3 Safety Representatives and Safety Committees Regulations 1977 383–4 Safety sampling, measuring performance 107 Safety Signs and Signals Regulations 1996 384–6 Sanitary conveniences 258, 335, 393 Scaffolds: fault checklist 302 fixed 293 Scotland, legal system 5 Scottish Environment Protection Agency see Environment Agency Seating, workplace environment 259 Security Equipment 272 Selection, contractors 40, 290 Self-employed 35 Service demands 62 Shear hazards 168 Shock, electric 189 Signs: means of escape from fire 215 Regulations 384 Silica hazards 231 Situational violations 57–8 Skin 228 dermatitis 228 protection 241 Slips and lapses, human errors 56–7 Smoke spread in buildings 207–8 Societal expectations 63 Sound pressure levels 261 Sources of law (England and Wales) 5–6 Specialist training 62 Staging, working above ground level 293 Stakeholders involvement, health and safety management 411–12 Standards, promotion 58–9 Static electricity 192–3 Stationary objects, pedestrian hazards 133–4 Statute law 6 liability levels 7–8 Stepladders 292–3 Stress, causes and prevention 269–70 Study skills 418 Studying: examinations 422–3 location 418 memory 420–2 organizing information 420 planning 418–19 reading 419 revision 419–20 Substances hazardous to health, control hierarchy 85 Suitability, hand tools 165 Supervision, risk control 83 Supervisors: emergency procedures 93

Index responsibilities 46 training 62 Supervisory/people control regulations 238 Supply chain 36–8 Supply of Machinery (Safety) Regulations 1992, 37, 159, 386–9 Surface spread, fire protection 217–18 Survey techniques, health risks 235–6 Task, manual handling assessment 145 Task design, ergonomics 250 Temperature, extremes 265 Tenosynovitis 257 Testing: fire fighting equipment 220 portable electrical appliances 197 Tetanus 285 Time exposure reduction, risk control 82 Toolbox talks 61 Torts and duties 6–7 Trade unions 64 Traffic route hazards and control 282–3 Training 60–2 fire emergency plans 220 incident investigation 121 induction 61 jobs 61–2 management 62 manual handling 148 risk control 82–3 safe systems of work 82–86 specialist 62 supervisors 62 work equipment hazards and control 159 Transport of hazardous waste be road 243 Trestles, working above ground level 292 Trip devices 176 Two-handed control devices, safety 176

Ultraviolet radiation 267 Urinary system 228 User checks, portable electrical appliances testing 197–8 User responsibilities, work equipment 164 Vehicle operation: control strategies 136–7 hazards 135–6 Vehicles: construction hazards and control 282–3 movement management 137 Vibration at Work Regulations 2005 389–91 Vibration Syndrome 252 Vibration white finger (VWF) 252 Violations, health and safety rules 57–8 Violence at work: causes and prevention 270–3 investigating 271 taking action 272 Visual inspection, portable electrical appliances testing 198 Visual problems, display screen equipment 257 VWF see Vibration white finger WAHR see Work at Height Regulations 2005 Washing facilities 258 Waste disposal 245–6, 285 Waste management licence 317–19 Water pollution 245 WBV see Whole body vibration Weil’s Disease (leptospirosis) 231 Welding hazards 268 Welfare: definition 2 facilities 83, 258, 284 physical and psychological hazards and control 258 risk control 83 Wet cement 284

Whole body vibration (WBV) 252, 253 Wood dust 285 Workplace exposure limits 233 Work at Height Regulations 2005 (WAHR) 279, 394–8 Work equipment: hand-held tools 164–7 hazards and control 159–85 mobile 169–71 suitability 159–60 user responsibilities 164 Work methods/patterns, risk control 82 Work permits 89–92 see also permits to work responsibilities 91–2 Work related upper limb disorders (WRULDs) 251–2 Work systems, risk control 82 Workers with a disability riskassessment 74–5 Workforce cooperation 42–3 Working above ground level 291–7 Working environment: equipment 163–4 manual handling assessment 147 Working Time Regulations 1998 (amended 1999) Regulations 401 Workplace environment 258–9 Workplace (Health Safety and Welfare) Regulations 1992 (amended 2002) 392–4 Workplace inspection examples 112–4 Workstations: design 250–8 workplace environment 258–9 WRULDs see Work related upper limb disorders Young persons, risk assessment 73–4

449