Solids Volume 1 Elastic Theory
Edited by
R. N. NABARRO Department ofPhysics University of the Witwatersrand Johannesbu...
169 downloads
1900 Views
25MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
Solids Volume 1 Elastic Theory
Edited by
R. N. NABARRO Department ofPhysics University of the Witwatersrand Johannesburg, South Africa
1979
North-Holland Publishing Company Amsterdam- New York- Oxford
© NORTH-HOLLAND PUBLISHING COMPANY, 1979 All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior permission of the copyright owner.
ISBN: Volume Volume Volume Volume Volume Set
1 o 720407567 2 0444 85004 X 3 o 444 85015 5 4 o 444 85025 2 5 o 444 85050 3 o 444 85269 7
Published by: NORTH-HOLLAND PUBLISHING COMPANY AMSTERDAM· NEW YORK· OXFORD
Sole distributors for the USA and Canada: ELSEVIER NORTH-HOLLAND, INC. 52 VANDERBILT AVENUE NEW YORK, N.Y. 10017
Library of Congress Cataloging in Main entry under title:
Data
Dislocations in solids. Bibliography. Includes index. CONTENTS: v. 1. The elastic theory. 1. Dislocations in crystals - Collected works. 2. Solid state physics Collected works. I. Nabarro, Frank Reginald Nunes, 1916QD921.D55 548'.842 78-10507 ISBN 0-7204-0756-7
Printed in Great Britain
The study of dislocations in solids has come of age. Our basic knowledge has expanded beyond the scope of a single volume, and we devote five volumes to the fundamental properties of dislocations and their influence on the properties of solids. In this first volume, J. Friedel outlines the whole field from a modern physical standpoint, A. M. Kosevich gives the theory of dislocations in an elastic continuum, J. W. Steeds and J. R. Willis extend this theory to anisotropic media, and J. D. Eshelby considers the interaction of dislocations with boundaries. Finally, B. K. Datta Gairola tackles the formidable problems which arise when we go beyond the approximations of linear elasticity, as the nature of the subject requires. Having painted the general picture, we plan to extend the series with a volume on the practical applications of dislocations, and finally a survey of recent developments. I cannot end this preface without thanking Mrs. O. L. Prior, who not only ensured some consistency of style and notation within and between the chapters, but also detected errors in the work of my most distinguished colleagues. The task of editing was greatly eased by Mrs. A. B. Alexander, my secretary for many years. F. R. N. Nabarro
Volume I
Preface v Contents vii
J. Friedel In troduction 1. A. M. Kosevich Crystal dislocations and the theory of elasticity 2. J. W. Steeds and J. R. Willis Dislocations in anisotropic media 3. J. D. Eshelby Boundary problems
167
4. B. K. D. Gairola Nonlinear elastic problems Author index 343 Subject index 347
223
143
33
/
Dislocations Introduction J. FRIEDEL Laboratoire de Physique des Solides Unioersite de Paris-Sud, 91405 Orsay, France
© North-Holland Publishing Company, 1979
Dislocations in Solids Edited by F. R. N. Nabarro
Introduction Introduction
3
1. Dislocations as singularities of an order parameter 3 1.1. Volterra process for continuous homogeneous and isotropic (classical) elastic media
3
1.2. Volterra's process in a continuous, homogeneous but anisotropic solid medium. Perfect and imperfect dislocations 8 1.3. Volterra's process for crystals
10
1.4. Burgers circuit for elastic solids
12
1.5. Extension of the notion of Burgers circuit for rotation dislocations. Disclinations 1.6. Possible dislocations in some molecular crystals 14 1.7. Singularities in liquid crystals 16 1.8. Singularities in other order parameters [Toulouse and Kleman] 2. Cores of translation dislocations in crystals 20 2.1. Core cut-off [Volterra] 20 2.2. Dislocations as solitons [Dehlinger, Peierls]
20
2.3. Splitting of the core [Heidenreich and Shockley] 2.4. Atomic description of the core 23 3. Dislocation ensembles 24 3.1. Dislocation networks in strained f.c.c. metals 3.2. Dislocation networks in recovered f.c.c. metals 3.3. Deformation and recovery in other structures 3.4. Deformation of polycrystals 25 3.5. Inhomogeneities in deformation 4. New techniques for old problems 5. More complex materials 27
26
26
6. Physical properties other than plasticity References 31
18
13
Reviewing the present state of the art, one is struck not only by a definite change in climate in the last ten years, and by a renewal of activity extending to newfields, but also by the permanence of some fundamental trends and underlying problems. In the new activities, one must count both the use of new techniques, which have helped to solve old problems, and also new fields of research: materials more complex than the simple metals of classical metallurgy, or physical properties other than plasticity. In these new activities, one finds the same complementarity between a macroscopic linearized description of long-distance distortions and an atomic description of the dislocation cores. Which aspect dominates a given physical property is still not always clear. But the major problem which is still not completely solved is that of bridging the gap between the properties of individual dislocations and the behaviour of dislocations "en masse", as observed in strongly deformed materials. We shall comment on these various aspects in turn.
22
1. Dislocations as singularities of an order parameter
24 25 25
We first focus our attention on the long-range distortions around dislocations. These distortions are small enough to be analyzed by linearized equations, e.g. the linear elasticity for solids. Dislocations appear as singularities of distortions. After comparing the standard Volterra construction and Burgers circuit characterization for continuous solids and crystals, we analyze their extension to other media such as plastic crystals and liquid crystals, and the relations of dislocations with other singularities of an order parameter.
30
1.1. Volterra process for continuous homogeneous and isotropic (classical) elastic media
The state of strain in such a medium can be defined by the spatial derivatives of the displacement vector u of each point I' from an assumed unstrained state ofthe medium. The corresponding state of stresses 0'(1') is obtained by Hooke's law, i.e. by the elastic constants which relate linearly the components of 0' to the distortions such as -!(ou)ox j + ouj/ox i ) . In the media discussed here, the elastic constants have the same value everywhere and reduce to two independent constants. An un strained medium has no stresses and strains, i.e. along an internal surface S, the two parts of the medium exert no force on each other; thus when a cut is made along S, the two lips S', S" of the cut have no tendency to move with respect to each other (fig. I). Some media are contrariwise internally strained and stressed in the absence of externally applied stresses. Volterra's construction was introduced to analyze such states ofinternal stresses as due to a continuous distribution ofdislocation
J. Friedel
4
Dislocations
an introduction
5
lines of infinitesimal strength. It is worth recalling the reasonings in this historical case before extending the results to more complex cases. Volterra's process is (fig. 1):
d
to cut the medium along a surface S limited by a line L. S', S" of the cut with respect to each other, without distorting them. y - to fill any empty space thus produced by (unstrained) material, or conversely to remove any extra matter possibly produced in this gedanken operation. <5 - to stick along the lips S', S" and remove the external stresses applied on S', Sf' to produce the displacement D(r). a
f3 - to displace the two lips
0'
Fig. 2
J$lJJL L
S"
v (a)
Equivalence of rotation (D, Ox) with rotation (D, 0' x') plus translation d.
By construction, D is a constant along the line L. In general, one knows that this is the sum of a translation b and of a rotation Q by an angle Q around an axis Ox. One can therefore have either rotation or translation dislocations or dislocations of a mixed character. It is useful to remember (fig. 2) that a rotation Q(Q, Ox) is equivalent to the sum of a rotation (Q, O'x') by the same amount around a new axis O'x' parallel to Ox and of a translation d, with (1)
(b)
Fig. 1 Volterra's process: (a) in perspective, (b) in section.
According to the self-evident Weingartern theorem, the, relative displacement without distortion ensures that, at the end of the process, internal distortions are continuous across the cut surface. Thus they can be (and indeed are) singular only along the line L. Such dislocation lines are thus characterized by: their geometrical position L. - their infinitesimal strength D. For the media considered here, the end result of Volterra's process is independent of the position of the cut surface S, if this does not touch the outside surface L of the medium. If the cut surface S extends to an outside free surface L, the final result of Volterra's process is still independent of the position of the cut, except for a total rotation of the medium, which does not alter the state of internal stresses. This result can be checked directly: it appears more obvious however with the use of the Burgers circuit (cf. below). In the definition of a relative displacement D one has to define which lip is called S' and which S". This is best done by fixing a direction along the line L of fig. 1, and deciding that, for instance, S' is on the left and S" on the right for an observer lying on the line L along that direction, and looking towards the cut surface. A reversal of the direction along L corresponds to a change of sign for D.
if I is the distance between the two axes of rotation.. For any mixed (translation + rotation) dislocation, one can choose the position of the axis Ox of rotation so that the translation b is parallel to Ox. Some further properties need be stressed; - Any distortion of the lip S' or S" during its displacement can be analyzed as due to a succession of displacements relative to the undistorted positions considered in Volterra's process (fig. 3). Such a distortion can therefore be thought of as adding to Volterra's simple loop L a succession of other dislocation loops l, l' along S' and S". As recalled earlier, any state of internal stress can be relieved by a suitable choice of internal cuts with distortion of the lips. Thus conversely, starting from a strain-free medium, any state of internal stresses and strains can be obtained by a succession of Volterra processes with distortion of the lips of the cuts; it can then be analyzed as due to a collection of dislocation lines.
L
Fig. 3 Distortion of lip S' of the cut in Volterra's process.
J. Friedel
Dislocations - an introduction
- A rotation dislocation (L, Q) is equivalent to a continuous distribution of infinitesimal translation dislocations. This is equivalent to stating that the empty space (or matter in excess) produced by a relative rotation (fig. 1)can be sliced into a succession of infinitely thin slices of constant thickness (fig. 4). Each slice s corresponds to a dislocation loop t with a translation vector equal to the thickness of the slice. Thus to define any state of internal stresses, one only needs translation dislocations.
This equation summarizes the fact that all three dislocations must have the same axis of rotation, with Q = Q 1 + Q 2 and b = + b 2 • At the triple nodes N, N', the dislocations involved then fulfil condition (2) if the directions of circulation are defined as in fig. 6a. More generally, when a number of dislocations meet at a node, their displacements fulfil the condition
6
7
(3) if the directions along dislocations are taken as all pointing towards the node (or all away from the node). This again means that all dislocations must have concurrent axes of rotation, with = 0 and b, = O. For example, the theorem recalled by eq, (1) shows that a pure rotation dislocation L (Q, Ox) can shift its axis of rotation Ox by I (dislocation L 1 ) if it emits a translation dislocation with a translation d given by eq. (1).
Fig. 4 Equivalence between a rotation dislocation L and a continuous distribution of infinitesimal translation dislocations I.
"
~ L1
1
rr
S'
1
S'
l
L
(a)
(a)
(b)
Fig. 5 Motion of a dislocation from L to L': (a) in perspective, (b) in section (conservative motion).
- If the cut surface 8 is extended by d S' (fig. 5), the dislocation line is displaced from L to L'. This usually increases the volume of empty space or of matter in excess, to be compensated for in the Volterra process. The only case where this would not hold would be if the displacement D were a pure translation b, and L were displaced along d8 parallel to b. Such a displacement of a translation dislocation parallel to its translation vector is called a conservative motion or glide. Any other motion is nonconservative and is called climb: it necessarily involves the creation of void or matter in excess, which can be compensated by diffusion only at high temperatures and for slow motion. Any cut surface 8 can branch into two other cut surfaces 8 1 and 8 2 without discontinuity of distortions along the branching line l, if the corresponding relative displacements D 1 and D 2 are such that (fig. 6): D
=
D1
+
D2.
(2)
Fig. 6(a), (b)
S"
S" 2
L 2
(b)
Branching of a cut surface S into two, S l ' S2'
As the distortions are singular along
there is in the immediate neighbourhood of
L a region where they are too large to be analyzed with linear elasticity. A specific
analysis, which will be considered in sect. 2, must be made in that range. Outside this core region, the strains produced by L are elastic, thus directly proportional to D for a given L. The elastic energy stored outside the core region is thus proportional to D 2 . As Li (DJ2 < (Li DJ2, it is clear that energy is gained by splitting a dislocation loop into anumber of loops of smaller displacements. This splitting can be spontaneous and progressive, by the nucleation and progression of nodes as described above, if the dislocations are allowed to move by glide or climb. The classical media discussed here have therefore a spontaneous tendency to store internal strains in the form of a continuous distribution of (translation) dislocations of infinitesimal strength. Then the linear elasticity approximation used here extends all the way to a very small core.
/ 8
J. Friedel
Dislocations
- The equivalency of fig. 4 shows that a rotation dislocation has a large energy compared with a translation dislocation, so that it is usually unlikely to be formed. More precisely, if the position L of the line is at a distance I from the axis of rotation, fig. 4 shows that the core energy is equivalent to the energy of a translation dislocation of translation about Q x I; this is very large if L is not practically along the axis of rotation Ox (l c::::: 0). Furthermore, the long-range distortion energy is impossibly large, in macroscopic tridimensional media, if parallel rotation dislocations of equal strength and opposite signs are not coupled at fairly short distances: otherwise, the translation dislocations I associated with the rotation dislocation L (fig. 4) build very large strains indeed. Using the theorem of eq. (1) we can then state that a pair of parallel rotation dislocations (Q, L), (- Q, L') is equivalent at long range to a translation dislocation of translation d related by eq. (1) to the distance I between the two dislocations L, L'. Only pairs at short distances I have energies which are not prohibitive. Furthermore the motion of such a dislocation pair would involve the emission by one dislocation and absorption by the other of a stream of translation dislocations (fig. 6) which would require a very large expense of energy: such a pair can be considered as "sessile". The corresponding cut surfaces are shown (fig. 7) for when the initial cut is along the two dislocations. S'
an introduction
9
necessarily bounding a surface S ofmisfit or grain boundary, where the anisotropy of the medium has a discontinuity. For perfect dislocations, anisotropy is continuous along the cut surface. D must necessarily be any translation b or a rotation Q that preserves the symmetry of the medium or a combination of the two. In the most anisotropic elastic medium, the possible rotations are all the rotations of multiples of ti around any axis. Less anisotropic elastic media can have axes of rotation of tn, 2n/3, ... or axes of revolution. The corresponding rotation dislocations are allowed, and their multiples. Owing to anisotropy, some rotation dislocations are thus forbidden, and some allowed rotation dislocations are quantized. Furthermore, and contrary to the isotropic case, the end result of a Volterra process for a quantized rotation dislocation is now dependent on the position of the cut surface. Take for instance a medium with cylindrical symmetry (and, as in all elastic classical media, a centre of symmetry). This can be visualized for instance as a frozen liquid crystal in the nematic mesomorphic phase. The specially allowed rotations are all rotations of multiples of 7[ around an axis perpendicular to the axis of revolution, and all rotations around the axis of revolution. Figure 8b, c, d pictures three con-
s
d
I c
t 1
/
t
S" Fig.7
/
1
1/
Cut surfaces S', SI/ associated with a pair of parallel and opposite rotation dislocations (U, L),
~
(-D, L').
L
Finally one can remark that two translations are commutable, but two rotations of finite strength are not in general commutable: exceptions are if the two rotations have the same axis, or if they have parallel axes and are opposite in strength. As a result, there is no difficulty in defining the rotation dislocations of a pair such as in fig. 7 when they have finite strength ± Q, nor in defining any configuration involving a finite number of translation dislocations or of rotation dislocation pairs of finite strength, so long as they do not cut each other.
/
/
-b
(a)
1.2. Volterra's process in a continuous, homogeneous but anisotropic solid medium. Perfect and imperfect dislocations The anisotropy appears in the tensor of elastic constants. In un strained homogeneous media, this tensor has the same value at all points. If the medium is anisotropic, there will obviously be a discontinuity along the cut surface at the end of the Volterra process, if D is not a symmetry operation of the medium. Such general dislocations are usually called imperfect or partial; they are
(b)
(c)
(d)
Fig. 8(b), (c), (d) Three configurations of an anisotropic medium with cylindrical symmetry around a rotation dislocation 2n normal to the axis of revolution, depending on the initial position of the cut surface (a).
J. Friedel
10
Dislocations
11
an introduction
figurations for a rotation of 2n around an axis perpendicular to the axis of revolution, depending on the initial position of the cut surface (fig. 8a). The lines are tangent to the local direction of the axis of revolution. As a result, a pair of parallel and opposite rotation dislocations can have different configurations, depending on their orientation with respect to the anisotropy. Figure 9 shows two configurations of high symmetry for ± tt dislocations of the same nature in the same medium.
(a)
(b)
Fig. 10 Dislocations in crystals: (a) translation dislocation, (b) rotation dislocation.
-B (a)
(b)
Fig. 9(a), (b) Two configurations of high symmetry for a pair of parallel and opposite (±n) dislocations, with axis normal to the axis of revolution in a medium with cylindrical symmetry. (a)
It can also be noted that such quantized rotation dislocations are only equivalent to continuous distributions of translation dislocations if it is accepted that a smooth lip such as S" (fig. 3) takes the average direction of the more rugged lip SI, thus rotates by Q with respect to the direction of the layers on SI.
Fig. 11 Examples of imperfect dislocations in a crystal: (a) translation dislocation with stacking fault F, (b) rotation dislocation with grain boundary B.
1.3. Volterra's process for crystals Here the core structure extends at least over an interatomic distance. The previous analysis extends to crystals by stating that, for a perfect dislocation, D must be an operation of symmetry of the crystalline structure and thus quantized: it can be a translation h equal to a period of the Bravais lattice (fig. lOa). it can be a rotation or a translation-rotation allowed by the symmetry of the crystal (fig. lOb). it can be a multiple or combination of these two types of displacement. As in anisotropic continuous media, the configuration of the crystal around a rotation dislocation depends on the initial orientation of the cut surface. Imperfect translation dislocations border stacking faults (fig. 11a) : imperfect rotation dislocations border (rotational) grain boundaries (fig. 11b). All other properties mentioned in the previous cases extend directly to crystals. Owing to energy considerations, and in conditions where perfect dislocations are reasonably mobile, one expects multiple dislocations to decompose spontaneously
- ---e
Fig. 12 Splitting of a translation b dislocation into a pair of rotation dislocations ±~n (L and L').
into their elementary components, corresponding to the shorter periods of the Bravais lattice and the elementary rotations or rotation-translations allowed by the lattice. The rotation dislocations can only occur in neighbouring pairs of parallel and opposite dislocations. Figure 12 gives an example in a hexagonal lattice. This can be considered as a special splitting of a straight translation dislocation into two rotation ones. Splitting of a perfect translation dislocation into partial translation dislocations bordering a ribbon of stacking fault occurs over more than a lattice period if the
13
J. Friedel
Dislocations - an introduction
stacking fault has especially low energy. Grain boundaries can have a free end as in fig. l lb, only if they correspond to a small rotation (subgrain boundaries). Largeangle grain boundaries meet each other nearly perfectly, so that only reduced internal strains are produced near their triple points.
(ii) If - D is a pure rotation, it varies with the position of C in the way expected if C
12
encloses a varying amount of a continuous distribution of infinitesimal translation dislocations, as defined in fig. 4. 1.5. Extension of the notion of Burgers circuit for rotation dislocations. Disclinations
1.4.
R."~"""",,
circuit for elastic solids
Another way of characterizing the line singularities of the internal stresses and strains in elastic solids is to draw a closed circuit C around the line in the strained solid, and to draw the corresponding circuit in the corresponding unstrained solid. This is possible because at long range, outside the core, the elastic displacement u(r) is well defined and varies continuously in space. '-
M'
S
The notion of Burgers vector is particularly well adapted for the translation dislocations for which it was invented. It is not sufficient to define rotation dislocations in anisotropic solids, whether continuous or crystalline, for it does not distinguish configurations such as those of figs. 8b, c, d, which depend on the orientation of the cut surface. An extension better adapted to rotation dislocations is to follow by continuity the orientation of a local trihedron P xyz which at each point P of C, in the unstrained solid, corresponds to a local trihedron of constant orientation on C in the strained solid (fig. 14). y
S' M
c
(a)
Fig. 13
(b)
(a)
Burgers circuit M M': (a) distorted solid, (b) undistorted solid.
Fig. 14
In the general case, the Burgers circuit in the undistorted solid will not be closed, but the displacement - D will have to be added to close it (fig. 13). This is connected with the fact that u(r) is multivalued, and increases by - D each time C goes once around L:
1~ du
-D.
(4)
This relation is obviously independent of the choice of the origin M on C. This shows clearly that the nature of the line singularity L can be defined as independent of the cut surface S in isotropic solids. In anisotropic ones, the choice of M fixes the relative orientation of D in the unstrained solid: the choice of the cut surface matters for rotation dislocations. We can also note that the sign of D is related to the direction on C, which can be defined unambiguously if a direction of circulation is chosen on L. A reversal in the directions of circulation on L, and thus C, again changes the sign of D. (i) If - D is a pure translation - b, this is a constant whatever the position of C, if it turns once around L. It is the Burgers vector of the translation dislocation.
(b)
Extension of the notion of Burgers circuit for rotation dislocations: (a) strained solid, (b) unstrained solid.
If C does not enclose a rotation dislocation, the total rotation P from M to M' is P xyz turns continuously by U zero. If C encloses a rotation dislocation of rotation from M to M' along C in the unstrained solid (fig. 14b). Again, this amount of rotation is independent of the origin on C (fig. 14a), and thus of the position of the cut surface: it is also independent of the position of C, if it turns once around L; it changes sign with the sign of circulation around C, and thus around L. Finally, if P xyz is defined on M by the local principal directions of anisotropy, we see that different orientations of P xyz on a given point M do correspond to different configurations, as shown for instance in fig. 8. Let (J) be the rotation of the trihedron P xyz from M to P along C, in the undistorted solid (fig. 14b). If C does not enclose a rotation dislocation, OJ describes a closed loop y when P describes C from M to M' (fig. 15a). It C' does enclose a rotation dislocation U, OJ describes an open loop y' of length - U. The possible values of U are distributed as described above, either in a continuous way or along spheres of various radii. The origin of y fixes the choice of cut surface. The description in rotation space (fig. ISb) neglects the translation part of the dislocation, and in particular defines the direction of the rotation axis but not its XYZ
14
J. Friedel
Dislocations - an introduction
position. To follow preceding uses, it might be useful to call that part of a rotation dislocation defined by an extended Burgers circuit disclination. The complementary description of the translation part is given by the Burgers vector in real space (fig. 15a).
- dislocations of the molecular orientation, defined with the use of an extended (rotational) Burgers circuit (fig. 17b).
~ ~
15
/ . // I II ~
-4-,.-/
~
(a)
(b)
~ _~~:I f 1
--{L
I
-.-
-.-
-+- -e-
\ -0-
\
-.- --.-
--.----.-
\ \-0-
-+-\
-.-
Fig. 15 Extended Burgers circuit: (a) real space, (b) rotation space. (a)
In all the solids described so far; the use of this extended Burgers circuit does not add any new information, because, as stated several times, rotation dislocations are equivalent to a distribution of translation ones. Thus except for differences such as those described in fig. 8, the use of normal Burgers circuits is sufficient. This is not so in other media, such as liquid crystals and perhaps some molecular crystals. 1.6. Possible dislocations in some molecular crystals In some molecular crystals, there exists a "plastic" phase just below the melting point where the component molecules keep a crystalline order of their centres of gravity but have a directional disorder at long range. It is just possible to imagine that, below such a phase, there might occur in some cases a phase where the molecules have directional long-range order which has a low energy of anisotropy: configurations such as figs. 16a, b, c, have similar energies. It is clear that, in such a case, there are two possible types of rotation dislocations, which are not necessarily coupled, as assumed so far: - dislocations of the lattice (fig. 17a), defined with the use of an ordinary Burgers circuit
o 00 o 00 o00 (a)
(b)
(c)
Fig. l6(a), (b), (c) Molecular crystal with a low energy of anisotropy in its directional order.
\
-.- -.- ---.- \ ~ ~ ~ ...... ~~\\~ -.-~~,,\
\
"
(b)
Fig. 17 Two types of rotation (1[) dislocations in molecular crystals with uncoupled lattice and directional ordering: (a) lattice dislocation, (b) directional dislocation (lines along the axes of the molecules).
The first type of dislocation can also be obtained by a modified Volterra process which acts only on the positions of the centres of gravity of the molecules without altering their orientation. The second type of dislocation can be obtained by another extension of the Volterra process, where along the cut surface S one rotates the molecules on each of the cut surfaces Sf S" with respect to each other without moving their centre of gravity [de Gennes]. The increase in the number of possible independent singularities is clearly related to the increased number of assumed independent parameters defining the crystalline order: in this case the positions of the lattice nodes and the directions ofthe molecules. Hence the notion of an extended Burgers circuit, which has components in the real translational space and in the space of rotations [Kleman]. We shall discuss as an example a simple case of molecules with an axis of revolution. A change in configuration of the directional order does not involve any shift of the molecules: it can a priori take place much more quickly than a change in the configuration ofthe centres ofgravity. As a result, a singularity produced in such a configuration of directional order by a Volterra process which is not stable energetically will spontaneously evolve towards a more favorable configuration. Two types of such evolutions can be envisaged: (i) Multiple rotation dislocations can split into elementary rotation dislocations" by the building and shifting of nodes. This is similar to but faster than the processes invoked for solids. (ii) Rotation dislocations of multiples of 2n can disappear as line singularities, by the molecules escaping into the third dimension when they are nearing the dislocation core. A Volterra 2n dislocation in this relaxed state is pictured in fig. 18, in projection normal to the line and in section. The sign means a molecule in the plane of figure; the sign til means a molecule normal to the plane of figure; and the sign r- means a
J. Friedel
16
Dislocations
molecule pointing to the right and towards the observer. It is intuitive that this escape into the third dimension might lower the energy for some elongations of the molecules. Thus such dislocations are not only topologically unstable in the sense that a small local distortion can suppress the line singularity: they might (or might not) be energetically unstable as well [Rault; Cladis and Kleman]. Cross-overs between the two regimes are expected for critical elongations of the molecules: singular lines are preferred to singular points for long molecules and thus have a large flexion elastic coefficient. L
<,
I
\
<,
~
/
I
\
<,
I
<,
---
<,
I -:
->
-,
\
I
/
/
/
--
/
N
/
I
\
/-
/'
-:
I
\ <.
-,
\
I
/
L·
~
~
-:
/ /
I
<,
-.
\
I
/ /
-L
Y
<,
/
/
I
\ \
<,
<,
............
-:
/
I
\ <.
-.
<
T
l-
I-
y
-I 1
/
-.
(b)
(a)
Fig. l8(a), (b)
<,
2n dislocation of the directional order, in a relaxed state.
As the escape can a priori occur towards the top or the bottom of fig. l8b, one conceives the possibility of two types of singular points, with a radial orientation around L as shown in fig. 19, at points Nand S [de Gennes]. Such a singular point is characterized by the topology of orientations of the molecules on a two-dimensional closed surface containing the point. Without going into the details of this analysis, one sees that such a closed surface plays for the singular point the role of an extended (rotational) Burgers circuit [Feldtkeller]. It can be checked easily that rotation dislocations of strength ± TC are on the contrary topologically stable: they cannot vanish by a small distortion near the core, and no independent singular points are connected with them [Bouligand]. 1.7. Singularities in
/
-:
T
.:
»>
1/
<
/
an introduction
crystals
It is not intended to discuss this topic fully here, since it is dealt with elsewhere in this
book, but only to stress some differences between liquid and solid crystals. Liquid crystals are anisotropic liquids built up with elongated and quasi-symmetrical molecules: - Nematics are three-dimensional liquids with an axis of revolution parallel to the molecules. - Cholesterics are three-dimensional liquids with a helical axis of rotation + translation normal to the molecules. - Smectics are two-dimensional liquids, i.e. layered structures where each layer, with molecules often normal to the layer (smectic A), has a fairly constant thickness and a two-dimensional liquid behavior.
I -:
->
.............
---
17
s ,,/"
....--
I
/
/
I
-,
/
/
I
\
<,
-.
L
Fig. 19 Two types of singular points of opposite signs Nand S in a perturbed directional order.
They are media with a possible directional order, but no (full) order in the position of the molecules. The distortions in this directional order can store an energy which can, in the limit of small distortions, be described in terms of generalized elastic constants. The situation is very similar to the distortions in direction for molecular crystals (fig. l7b). (i) All possible individual line singularities can be defined starting from a Volterra process applied as if the medium were solid and then allowing for the liquid possible un quantized translation and rotation motions which can relax some of the strains. This relaxation disperses and eliminates all singularities which are not quantized and reduces the energy stored in the remaining quantized ones. It allows some of these dislocations to move and bend, keeping their axes of rotation in their cores. In some cases, it also allows a rotation dislocation to rotate its axis of rotation. All these motions can be visualized as the emission or absorption of continuous distributions of infinitesimal (un quantized) translation and rotation dislocations. As a result rotation dislocations can exist fairly isolated from each other and move freely in liquid crystals. In the simplest case of nematics taken as an example, all translation dislocations and the rotation dislocations with an axis of rotation parallel to the molecules are
18
J. Friedel
eliminated. There only remain the quantized rotation dislocations, of multiples of tt with axes normal to the axis of revolution of the nematic structure. As in the molecular crystals, a further relaxation of the cores suppresses the line singularity, by an escape of the molecules into the third dimension, if the rotation is an even multiple of ti : only singular points remain in that case [Nabarro]. For odd multiples of n, the rotation dislocations have energies which increase only logarithmically with the distance between opposite dislocations, as for translation dislocations in solids. Singular points and lines move freely in the nematic. (ii) As all the translation component is relaxed, the remaining rotation dislocations are most easily characterized by the use of the rotational Burgers circuit discussed for molecular crystals (fig. 15) or of the modified Volterra process introduced by de Gennes. The same is true for some of the dislocations or other equivalent line singularities (focal conics) in the other mesomorphic phases ofliquid crystals. Some other dislocations of these media, which involve at least in part a translation, and the general connections with similar arrangements in solids, need the use of a fully extended (translational + rotational) Burgers circuit. Some of these latter problems are more easily understood in terms of a Volterra process, which must however be used with care in the more complex cases. 1.8. Singularities of other order parameters [Toulouse and Kleman]
Dislocations
19
an introduction
saturated with dislocations; it is however better grounded in second-order transitions, if only because melting is a first-order transition. Consider as an example a classical ferromagnetic crystal, with dimensionality d and n magnetic degrees of freedom per lattice site: d = 1 for a line, 2 for a plane, 3 for a volume; n = 1for the Ising coupling, 2 for the xy coupling, 3 for the Heisenberg coupling. It can be directly checked from the discussion above that the topologically stable defects are respectively points p and line 1 for d = 3 and n = 2 and 3 respectively (fig. 20). The results can be obviously extended to plane singularities P for d = 3, n = I; and, for d :1= 3, the point, line and plane singularities fall on straight lines with a slope one in the (n, d) diagram, a general topological result which can be directly checked. d
4 0
2
3
4
5
2
The study of elastic singularities in crystals and liquid crystals has recently stimulated the general topological analysis of possible singularities of order parameters. A few points might be stressed here: Each type of singularity can be defined using an extended Burgers circuit. - General theorems allow one to state the types of topologically stable singularities. An energy analysis, using the full equation of state for the order parameter, would be necessary to show whether topologically unstable singularities are also energetically unstable. This is however usually to be expected, as the core part of a singularity is generally a region of large stored energy, and it pays to reduce its extent (an obvious counterexample is the hyperbolic branch of a couple of focal conics in an A smectic, which is topologically unstable but energetically stable at least over part of its length: fig. 8 also shows that topologically equivalent configurations need not have equal energies). Singularities ofthe order parameter are expected to be unstable at low temperatures, except possibly for quantum effects in quantum solids (cf. below). Because of their positional and vibrational entropy, one expects them to be thermally excited. Because of their large internal energy, the concentrations in thermal equilibrium usually remain small until, possibly, a critical temperature above which they appear in greater numbers. The collective character of such a possible transition is due to the fact that these singularities interact at long range in such a way as to reduce their internal energy. Thus the singularities of the order parameter might play a specific role in describing the short-range order above the critical temperature where order disappears. This is a suggestion inspired by the old description of a liquid as a crystal
o
-,
Fig. 20 (n, d) diagram for ordered media with a vector order parameter. The hatched region has no possible order at finite temperature.
Thus for d = 3, magnetic walls are singular planes only in the Ising model. In the xy or Heisenberg models, they are regions of continuous rotation of the magnetic moments, only stabilized by the energy of crystalline anisotropy. In the xy model, which forces the magnetic moments to lie in a given xy plane, these walls can contain line singularities, along which the rotation in the wall changes its sign (Neel lines). In the Heisenberg model, the magnetic moments can escape in the third dimension, so that only singular points are stable (Bloch points). For d = 2, n = 2, there is a singular point in the region of allowed order; it is known that although the order temperature is zero, there is a finite temperature above which singular points (vortices) appear in great number. This would be a case where the catastrophic appearance of the singularity is not related to the ordering temperature. Strong analogies exist between quantized dislocations in crystals and liquid crystals and vortex lines in suprafluids or supraconductors. Analogies also exist between the continuous distribution of infinitesimal dislocations and the distribution
J. Friedel
Dislocations - an introduction
of vorticity in normal liquids in motion. Indeed one can suggest that the appearance of turbulence under strong perturbations is a cooperative creation of vorticity somewhat akin to the melting of crystals at high enough temperatures.
This problem has analogies with that of a layer of atoms interacting elastically and deposited on a rigid substrate with which they interact by a potential such as V(r) [Frenkel and Kontorowa]. Some aspects of this type of model need stressing. The tine singularity of a complete elastic body is replaced by a continuous distribution of infinitesimal dislocation along P. The width of this distribution defines a core which is more extended the smaller the amplitude of V is compared with the elastic constants of the two half-crystals. The total line tension of the line, its anisotropy and the frictional force against its motion all decrease with an increasing width.
20
2. Cores of translation dislocations in crystals Deviations from linear elasticity occur near the centre of the line singularities, in the core region. Three types of approach have been used successively in this field, which we shall briefly discuss.
21
L
2.1. Core cut-off [Volterra] This assumes the elastic regime to apply down to within a short distance of the dislocation line, and neglects what happens in the core region. With a suitable core cut-off distance roof the order of the Burgers vector if this is of atomic size, this approximation was shown by Frank to give a fair representation of the total energy. Two corrections should be made:
y
deviations from linear elasticity outside the core - energy stored in the quasi-amorphous atomic structure in the core. However for dislocation densities which are not too large, the long-range elastic distortions dominate in the total energy, and these corrections are often not very important. This approximation is much used for crystal dislocations and has been extended to continuous distributions of dislocations in solids. Deviations from linear elasticity have been used to analyze the couplings with phonons. The approximation essentially neglects the crystallographic and chemical aspects of the interatomic bondings which are modified in the core when a dislocation is created or moved. Even taking into account the anisotropy of elastic constants, one cannot usually hope to analyze in this simple model those properties which follow from the directionality of the crystal structure or of the atomic bonding. 2.2. Dislocations as solitons [Dehlinger, Peierls] To analyze the configuration and motion of a dislocation line in a crystallographic glide plane P, Dehlinger, and then Peierls, used a simplified description of the crystal structure, by assuming that the two half-crystals separated by P were two continuous elastic bodies interacting by a potential V varying sinusoidally with the local relative displacement u(r) of the two half-crystals across P: V =
L
A sin (ku
+ ¢)
dzr.
The wavelength I = 2n/k represents the atomic periodicity along P, and the Burgers vector is assumed to have a component A along k.
o (a)
Fig. 21
(c)
Dislocations in a Peierls sinusoidal potential: (a) straight line perpendicular to k, (b) general "straight" dislocation, (c) kink.
For straight lines perpendicular to k., the motion reduces to a one-dimensional problem equivalent to other problems with the same non-linear potential. This general class ofproblems is reminiscent of that of the solitary wave in hydrodynamics, hence the name of soliton now attached to the corresponding extended singularity. Such a straight line has equilibrium positions distant from each other by multiples of }L. The energy humps between these positions can be overcome, and the dislocation moves as a whole if a stress is applied that is large enough to overcome this solid friction. This is the zero-temperature Peierls stress O'p. A line initially not perpendicular to k will move easily under any small applied stress, until a part perpendicular to k has developed; this is then trapped in the "sessile" position until O'p is applied (fig. 2Ia). Indeed a line not perpendicular to k has a tendency to take a somewhat sinusoidal form so as to lie longer along the valleys of energy minima than across the energy hills (fig. 21b). It can then be considered as possessing a succession of kinks which bring it from one valley to the next (fig. 2Ic). At finite temperatures, a dislocation initially along one energy valley can move under a stress less than O'p by the thermal activation of a double kink in which the individual kinks, once formed, separate quickly because of their extremely shortrange interactions.
J. Friedel
22
This type of model has been much used to explain: a the choice of close-packed crystallographic planes as glide planes, by trying to relate these to such planes, which are distant from each other, with particularly small amplitudes A in the potential V, and thus particularly small line tension for the dislocations. f3 the value of the zero-temperature Peierls stress, related to the value of A. y - the temperature variation of the Peierls stress and internal friction processes assumed to be related to the creation and destruction ofdouble kinks under alternating stresses (Bordoni peak). It is clear that a more elaborate description of the core is needed for case a, especially for close-packed structures, and that case f3 is at best a way of fixing the amplitude A of the potential V. The double-kink model looks more promising for case y. However it should, in most cases, be reinterpreted, the hills and dales of fig. 21 representing much more complex core configurations than those assumed in the soliton model. Indeed, if taken at its face value, the Peierls model should take into account also the periodic variation of V perpendicular to k, This would lead to a periodic variation of the dislocation energy in the y direction (fig. 21) and thus to a friction on the glide of kinks. Double kink formation is expected to limit the speed of straight dislocations at low temperatures, and kink motion of the speed of curved dislocations at high temperatures, in the usual case where the first process has the larger activation energy.
2.3. Splitting of the core [Heidenreich and Shockley] In most compact simple structures, and especially in metals, some planes of stacking fault which perturb little the arrangements offirst-nearest neighbors, and thus have low energy if the interatomic forces are not directional. This is true along the (111) planes of f.c.c., the (110) and (100) of b.c.c., the basal and some prismatic and pyramidal planes ofh.c.p. Even in the diamond cubic covalent structures, (111) stacking faults can be produced which respect the angles as well as the lengths of nearest-neighbor bonds. Perfect dislocations can then lower their energy by splitting into partials separated by such stacking faults. Figure 22 schematizes some such cases met in nature. Another type of possible splitting is for a translational dislocation to split into a pair of rotational ones, as schematized in fig. 12. More complex splittings can be thought of in crystals with larger cells. Such splittings are only well defined if the stacking-fault energy is low enough for its equilibrium width to be more than one atomic distance. This case is met in many metals and covalent structures.
~/////.--
(a)
Fig.22
(b)
Three cases of dislocation splitting: (a) glissile, (b) and (c) sessile.
Dislocations
an introduction
23
It is also seen that all but the case of fig. 22a are sessile: the dislocation must recompose to be able to glide as a whole; this requires a temperature high enough for a "constriction" to appear and develop by thermal fluctuation; or exceptionally, it can require a large enough applied stress for recombination to be forced on the whole of the dislocation. In the case a, glide normally occurs in the plane of splitting. Cross slip into another slip plane requires a high temperature for thermally activated cross slip and/or a large enough applied stress. This concept of splitting has been checked directly using transmission electron microscopy. It has helped to understand many aspects of slip in common metals and covalents: choice of slip plane in the cubic and hexagonal structures (fig. 22a), thermally activated cross slip in these phases, more difficult motion of screw than edge in b.c.c. structures, owing to a sessile splitting of the screws (fig. 22c), relation of the amount of splitting with ease of twinning.... It is thus clear that, when wide, such splittings must be taken into account in the study of dislocations. One outstanding question is then the exact value ofthe stackingfault energy, and its variation with composition or with temperature. When not so wide, such splittings can give only a qualitative description of the properties of dislocations. This is for instance the case with metals such as Al or with the ionic solids.
2.4. Atomic description of the core Compact structures with dislocations not widely split or complex structures are obviously better treated by a direct computation of the atomic structure of the core. Even in widely split dislocations, there remains the description of the cores of the partials. Exact computations are practically impossible except in rare gases and possibly simple ionic solids. For metals and covalents, the interatomic interactions are but roughly known and only model computations can be made, often of somewhat doubtful validity. A further difficulty is that one can compute simply only dislocations in equilibrium, in simple straight positions, possibly under stress. One can thus manage to compute positions of lowest energy and something like the zero-temperature Peierls stress: but nothing related to thermally activated processes has been computed so far. Configurations of dislocations pointing in less close-packed directions, in a glide plane, or going out of their glide planes, have not been practically tackled either. It is clear however that a much more aggressive policy in this field would be invaluable, if simple typical situations were fully studied with reasonable model interatomic forces. A general remark can however be made: in covalent structures, the creation and motion of a core, whether for a perfect (unsplit) or for a partial dislocation, will involve the breaking of interatomic bonds. In the Peierls language, one expects nearly equally difficult creation and motion of kinks, thus large Peierls stress at zero temperature and thermally activated glide at high temperature, with an energy of activation of the order of the bonding energy so a difficult glide even though the split disloca-
24
J. Friedel
tions are "glissile" in the diamond cubic structure: one also expects that, owing to this large friction, the partials do not necessarily take their equilibrium distance, or even might keep together in a perfect dislocation on some lengths of the dislocations. This seems indeed the case in these solids. Contrariwise, in metals and ionic solids, with essentially central forces, the motion of a core is not expected to give rise to a large frictional force, because the effects or' some bonds widening while others shorten should more or less compensate. Indeed the Peierls friction on split dislocations which are glissile usually seems to be very small, if at all measurable. Indeed the Bordoni peaks of internal friction, if due to the thermally activated formation or motion of kinks, occur at low temperatures and involve reduced energies. Easy glide of dislocations thus require two types of conditions to be fulfilled together a geometrical condition, on glissile splitting a bonding condition, on motion of the core.
Dislocations
an introduction
25
observation and the characterization of its long-range (pile-up) versus short-range (three-dimensional network) structure and of its anisotropy. - Stage III or parabolic stage: in this stage, the external stresses are large enough to produce a recovery by cross slip which decreases the dislocation density and thus produces a hardening less marked than in stage II. More or less well defined polygonized cell structures are developed. If the beginning of stage II has given rise to many analyses of cross slip and its altogether convincing description, the state of affairs is much less clear once the cell structure is established. No convincing description exists so far of the processes by which it grows and thus produces a parabolic type of hardening. It is probable that one of the processes involved in the growth of the structure is a catastrophic destruction by cross slip of some polygonized walls, which would start on the most stressed dislocation, and then propagate to its neighbors. The same cell structure occurs in medium-temperature creep and its evolution should be studied there too. 3.2. Dislocation networks in recovered f.c.c, metals
3.1. Dislocation networks in strained f.c.c. metals
Studies of heat treatments after these various strainings in f.c.c. metals show better defined polygonized cell structures. At high temperatures, polygonization grows by vacancy diffusion, by mechanisms which are well understood in principle. The same cells occur in high-temperature creep. It is however noteworthy that no very systematic studies of polygonization have been made after well defined deformations in the various stages recalled above, to see in detail the relations between the deformation and polygonization textures.
It is indeed clear that the three stages in the straining curves of f.c.c. single crystals do
3.3. Deformation and recovery in other structures
3. Dislocation ensembles If the properties of individual dislocations are, on the whole, mastered and understood
in the simpler crystalline structures, one is very far indeed from this happy state of affairs for the large dislocation densities involved in straining processes.
correspond to three rather different types of dislocation arrangements: - Stage I or easy glide, where dislocations of one slip system mostly develop. This is a rather inhomogeneous distribution, usually with slip bands parallel to the active (111) plane and containing more dislocations than the surrounding material. Hardening seems connected with kink bands normal to the [11OJ active slip direction and made up of loose pile-ups of dislocations of opposite signs. Clearly this is a difficult stage to describe by a few parameters and to analyze in detail. Stage II, or the linear hardening stage, where secondary slip systems become very active: they build with the primary system sessile Cottrell-Lomer locks on which active dislocations can pile up; stress relaxation of the pile-ups by secondary systems finally leads to a three-dimensional network of increasing density. It has been fairly clearly demonstrated that, in this range, hardening is mainly (but not only) a function of the average density of this three-dimensional network of dislocations. But the fact that the network is not isotropic is demonstrated by experiments where, after straining in one direction, one starts straining in another, possibly even the opposite, direction; one always observes in the second straining an elastic limit lower than that produced in the first one (Bauschinger effect). Much remains to be done on the development of the dislocation network, especially under complex straining conditions, on its
It is somewhat of a surprise to observe that the same three stages of deformation and the same recovery structures are observed in a number of other metallic structures notably the b.c.c. and, with some qualifications, the h.c.p. ones. The same is true for a number of ionic solids. Especially in the b.c.c. metals, it is not clear what are the equivalents of the Cottrell-Lomer locks of stage II or cross slip of stage III in the f.c.c. structure. 3.4. Deformation of polycrystals The relation of the straining of a polycrystal to that of a single crystal is understood in principle, and Kroner's work in this field has much helped to develop a simple and realistic approximation. The study of large-deformation textures has been much helped by the use of the development in spherical harmonics of X-ray or neutron pole figures. It is certainly one field where the points of view of mechanics and metallurgy have been brought very near. Still, the plastic properties of the individual grains are very schematized: and the effect on textures of twinning or of the development of stacking faults is still far from clear. The same is of course true for the relations between textures of deformation and recrystallization.
26
Dislocations - an introduction
J. Friedel
3.5. Inhomogeneities in deformation We include here various topics: - Luders bands. - Thermoplastic instabilities. - Striction and failure and, conversely, superplasticity. _ Alternations of recrystallization and deformation in hot working. _ Plastic deformation in front of a moving crack and the connected problem offatigue. In this field, emphasis in recent years has been on trying to develop macroscopic mechanical models that help to describe satisfactorily the inhomogeneities. This was particularly clear in fracture and fatigue, where the measurement of the plastic friction due to propagation in various materials in various conditions helped to reassure industrialists, and especially those in aeronautics, about the harmlessness of many small cracks produced. The same approach has helped to define the favourable values of coefficients in phenomenological equations of plastic behaviour to obtain superplasticity. It now seems time to reassess from a fundamental point of view the wealth of phenomenological results thus obtained, and to try and understand the elementary processes involved, with a view to developing some systematics.
4. New techniques for old problems Transmission electron microscopy has remained the major tool for the observation of dislocations in motion in crystals. Three significant developments must be stressed:
_ The use of special contrast techniques has allowed one to observe details on a nearly atomic scale. Thus the weak-beam contrast has led to the systematic study of the splitting of dislocation cores in f.c.c. metals and diamond cubic semiconductors, confirming earlier but controversial results in the latter case. The use of two-beam contrasts allows a direct inspection of the regularity of the crystal structpre on the scale of the lattice cells and of the atomic structure of dislocation cores. ~ But an even more important development has been the systematic use of high energy electron microscopy. This technique has its own problems, be it the m~)fe difficult analysis of the many-beam contrasts or the radiation damage produced by the electrons. But it is essential to observe dislocation structures on a scale of a few 100 to 1000 A, as produced in many straining conditions. This technique has confirmed in detail the models of micro and macroyields in b.c.c, metals at low temperatures associated with a low and strongly temperature-dependent mobility of the screw dislocations, as predicted from an analysis of possible core splittings in such lattices. Systematic observations of straining and recovery at higher temperatures seem to give very interesting results on cross slipping and diffusive motions of dislocations. Finally observation in the microscope has been essential to our understanding of the early stages of formation of loops, tetrahedra or voids by radiation damage. _ Very fragile materials are now observed, using mostly low temperatures and short
27
observation times: this refers to ionic solids, polymers, biological materials akin to liquid crystals. The X-ray techniques are also being rapidly extended at the moment: - The Lang technique is extended to the observation of moving defects by the use of new fast detectors and more intense X-ray beams. But really fast moving defects are now observed by a technique more akin to the Guinier-Tennevin set-up, using the very intense white spectrum of cyclotron radiation. - A systematic X-ray analysis of deformation and recrystallization textures has been made possible by the use of a mathematical development in spherical harmonics of the intensity of the X-ray spectra. The neutron techniques have also been developed. - Neutron topography has proved interesting in magnetic materials. - Texture analysis can also be made now using neutrons. - The distortions. around dislocations have been studied in magnetic materials. Ion emission microscopy has mostly been used to try to study the atomic structure of the dislocation cores. This has led so far to results less convincing than for the structure of grain boundaries, mostly because the high electric field present during the observation probably alters the amount of splitting near the surface. In addition the optical microscope has been systematically used to study textures and defects in liquid crystals and related materials. Finally, in the study of the physical properties of dislocations, all the corresponding methods are used. Two recent results are
- The connection in luminescent diamonds between the distribution of luminescent centres and of dislocations, as observed by the Lang technique. The observation by EPR of large magnetic polarons associated with extra carriers trapped on otherwise neutral dislocations in semiconductors, with paramagnetic broken bonds in their core.
5. More complex materials Based on a reasonable understanding of the simple metal oxides and semiconductors which developed in the '50's, one observes in the last ten years a definite trend towards broadening the field of research to include more complex materials. This has brought the classical physical metallurgists in contact with other fields of research, with mutual benefit in cases such as geophysics where the contact has been prolonged and deep. In other fields, one has seen physicists painfully rediscovering well known results ... - The field of ionic solids, and especially oxides, is of direct interest to metallurgists; and it is somewhat surprising that it took so long to develop in full in the dislocation field. It probably has to be realized that the plastic properties are dominated in these materials, as in metals, by the structure and behavior of the core. Systematic studies
28
Dislocations - an introduction
J. Friedel
of the effect of crystal structure, temperature and purity are less advanced in this general field, admittedly more complex than that of metals. Applications to magnetism, geophysics and building materials are, however, obvious. - Classical covalent solids used by the semiconductor industry have been the subject of much technical research. There seems to be now a better contact between electronics and metallurgy laboratories on the characterization and study of dislocations. But the detailed description of the atomic and electronic structures of the dislocation cores and their connection with the way the dislocations were introduced, or with doping and illumination, are still matter of controversy. A more systematic relation of plastic properties with cohesion in semiconductive compounds and alloys would probably be rewarding, as clearly the creation and motion of dislocations involves the breaking of covalent bonds. A definite extension to more exotic materials, such as covalent chain crystals (S, Se, Te) or covalent plane crystals (graphite, arsenic) has been started and clearly shows a preference for dislocations which avoid the breaking of covalent bonds, both for their creation and their motion. In the field of molecular crystals, very little work has taken place so far that could be called systematic. Thus the plastic properties of "plastic" crystals, the defects in the crystallinity of polymers, the interaction of dislocations and domain walls in organic ferroelectrics are three examples of pretty open questions. The related field of liquid crystals has seen an explosive growth in the last years. This is a classical example of discontinuous growth on the research front. Indeed the mesomorphic phases of "thermotropic" liquid crystals were observed by Lehmann at the end ofthe last century and classified by G. Friedel before 1920. Lehmann observed the line singularities in the molecular arrangements of these oriented liquids, and G. Friedel described essentially correctly the molecular arrangements around the ,line and point singularities. These line discontinuities are in most cases equivalent to Volterra's rotation dislocations. They are therefore very clearly the earliest examples of dislocations observed in nature and understood as such. What made this possible was the low viscosity of liquid crystals, which allows fast recovery thus a quick achievement of nearly perfect arrangements, with low densities of dislocations, together with a strong coupling of light with the distortions around these defects, which makes them easily observable in the ordinary microscope. Nothing but a mental block or a lack of impetus from possible applications can then explain why a field which was flourishing in the 1920's lay practically dormant for more than 30 years before getting a new lease of life. This proved to be extremely fruitful on the dislocation side, by extending the notion of line singularities to ordered structure without a lattice, in phases of increasing complexity. Besides direct connections with line singularities in related problems of magnetism, suprafluidity or supraconductivity, work in liquid crystals has been the starting point of a general classification of singularities of ordered structures which is briefly analyzed above. It has been also extended to related structures: "lyotropic" liquid crystal phases of the soap family, and various biological materials (membranes, some chromosomes and even the cellular arrangement of the skin of some crabs !). This rapid survey should also mention work on the crystalline phases of rare gases.
1U'''''JA~'~~
29
rather humdrum and somewhat incomplete work on the heavier gases, one mention at least two recent works on He.
- Work on crystalline He 4 under pressure seems to show conclusively that, at least in the range of temperatures explored, plasticity in this phase is through a classical and hysteretic motion of dislocations. Thus evidence is there against a fast quantum tunnelling of either dislocations or vacancies. - Work on crystalline He 3 again indicates that dislocations can be accumulated by work hardening, and that they can capture vacancies and pin them down. A related problem is that of the possi ble plastic deformation of the crystalline crust of neutron stars. It seems possible that the "starquakes" observed in some pulsars are due to "catastrophic" deformations of the crust. However, by analogy with what is known of other supraconductive b.c.c. materials such as Nb, it seems likely that these are not cracks but localized thermal spikes developed in a poor conductor by the heat released in local deformation bands: this local heating strongly decreases the macroyield stress in the band, thus favouring an accelerated straining within the bands. Finally one should bear in mind that Volterra's initial analysis referred to the internal stresses of a macroscopic continuous solid. Thus the concept of continuous distribution of infinitesimal dislocations has had a rich and rewarding field of application in the analysis of internal elastic stresses produced in various ways: inside and around more or less coherent precipitates; around cracks and near indenters; in polycrystalline or polyphase materials prepared in various ways so that the various grains mutually exert internal stresses; in non-saturated magnetic materials, when a magnetostriction is present; etc ... It is also clear that any grain boundary and some phase boundaries can formally be described as equivalent to a (planar) continuous distribution of infinitesimal dislocations. A relative sliding of the grains parallel to a fairly flat boundary can be thought of as due to an evolution and motion of these dislocations along the boundary. It was also known for a long time that in low-angle boundaries, such a distribution condenses into a discontinuous distribution of lattice dislocations. It is one of the advances of recent years to have shown that in many cases large-angle boundaries can be thought of as a similar superposition of a perfect twinning arrangement and of a small-angle boundary produced by an array of twinning dislocations. These perfect twins are often of the kind first introduced by G. Friedel, i.e. such that the two grains have a common superlattice. Still along the same lines of thought, one can think of a liquid or a glass as a crystal full of dislocations. This is not a particularly helpful description, as these dislocations very strongly interact and thus have not much physical individuality. But this picture helps to understand that a glass can be plastically deformed at low temperatures by the relative shear of two parts along a sliding surface that is macroscopically flat, through the motion of a continuous distribution of supplementary infinitesimal dislocations. If the surface of contact was atomically smooth, this motion could be a pure glide. And, after a suitable amount of slip, some kind of short-range order could be reestablished across the sliding surface, thus minimizing the energy of the "stacking fault" produced along the slipping surface. Because of atomic roughnesses, some irregular climb on an atomic scale is involved, leading to irregular compressions and
30
J. Friedel
tensions across the slipping surface which compensate at large distances and thus do not store much energy. It is indeed the same kind of description which has been used to describe the relative sliding of two crystalsalong a fairly flat boundary.
6. Physical properties other than plasticity Besides general connections with properties of singularities of other ordered phases, such as magnetism, supraconductivity, suprafluidity, one should mention four fields of special interest: - Electronic properties in insulators and semiconductors. The direct connection of crystal dislocations with the transport and optical properties of such materials has been clear for many years, and much effort has been spent in the electronics industry either to eliminate the dislocations for "perfect" crystals or at least to characterize the dislocation contents. General ideas about acceptor and donor states related either to broken bonds in the dislocation core or to the long-range deformation potential have been aired for quite a time. However very little effort has been made so far to study the electronic structure and excitations of dislocations with known geometry and core structure. This is particularly clear in Si or Ge where core splitting is only beginning to be studied; but even in Te, where some systematics ofthis kind have been tried, it is far from clear that the dislocations introduced are as regular and straight as was assumed. The influence of dislocation networks on the hysteresis of magnetism or supraconductivity has been similarly studied with a view to technical applications. But more work would be of interest on the exact nature of the coupling of individual dislocations with the magnetic or supraconductive singularities; also works on the hysteresis due to well defined dislocation arrays are still very few: e.g. screw dislocations produced by macroyield at low temperature in supraconductive Nb or ferromagnetic iron; three-dimensional networks produced by low temperature straining in ferromagnetic nickel; well defined cell structures obtained in stage III of all these metals. It is also clear that the magnetic hysteresis behaviour of strained or polycrystalline ferromagnets has many aspects similar to the plastic hysteresis of crystals, and that the same kind of statistical models probably apply. - Surface properties. The role of emerging dislocations in the now classical fields of crystal growth and thermal or chemical etching could with advantage be reconsidered with modern methods of surface observation.
But a more active field has recently been that of epitaxial layers. It is clear now, as had been suggested theoretically, that the strongly bonded chemisorbed epitaxial layers can adapt perfectly on an atomically smooth crystalline substrate if their thickness is of atomic dimensions. Epitaxial dislocations appear on the interface with the substrate for thick enough layers, so as to relieve the growing strains when as usual the two phases have not exactly the same lattice parameters. Volume dislocations can also appear to relieve further strains due to a difference in thermal expansion of the two phases, if the epitaxial layer is submitted to a change in temperature after being formed; volume dislocations also appear to relieve chemical
Dislocations
an introduction
31
stresses if, owing to heat treatment, interdiffusion can occur across the interface and concentration gradients build up near to it. All these well-known aspects seem only recently to have been taken properly into account by the electronics industry in problems of epitaxial p-n junctions in semiconductors or magnetic bubble deposits. More loosely bonded physisorbed epitaxial layers can show more complex behaviors even at atomic thicknesses. In the typical field of rare gas monolayers on (0001) planes of graphite, epitaxy at low temperature can be exactly coherent or show an approximate epitaxy which preserves the directions of the atomic rows; this is obtained by introducing a grid of epitaxial (translation) dislocations. As temperature increases or the vapour pressure decreases, one seems to reach a quasi-liquid state of the monolayer, which can possibly be described by the cooperative stabilization of (rotation or translation) dislocations piercing the monolayer. The description is still deduced from rather indirect or global observations, and it would indeed be of fundamental interest to observe directly and characterize in more detail the dislocations involved in these various phases. Indeed various aspects are still poorly understood: the thermodynamics of melting; and the conditions of approximate epitaxy (configuration, hysteresis, entropy of vibration). The "melting temperature" of these two-dimensional layers shows some similarity to the temperature of appearance of vortices in ferromagnetic monolayers with moments in the layer (xy model); the passage from approximate to exact epitaxy is analogous to many other cases of passages from incommensurate to commensurate order parameters in threedimensional lattice or magnetic superstructures. - In the field of radiation damage, great efforts have been made to understand the nucleation and development of dislocation networks and/or cavities by elimination ofthe Frenkel defects produced under heavy radiation doses. In the condition oflarge supersaturations which can obtain, it is not clear whether one can use concepts of near equilibrium or, more likely, a purely kinetic description. This certainly applies to the nucleation of dislocation loops versus voids (where gaseous atoms are needed) and the choice of atomic planes for the loops in anisotropic materials. But this remark might possibly apply also to the formation of more or less regular arrays of voids, loops or tetrahedra observed very frequently under heavy doses. The whole field still needs very basic and fundamental experiments to decide between various possible interpretations. This is crucial in understanding the problems of irradiation swelling and irradiation growth met in the materials used in fast nuclear reactors.
References for sect. 1 Bou1igand, Y., J. Physique 35 (1974) 215, 959. Burgers, J. M., Proc. Kon. Ned. Akad. Wet. 42 (1939) 293, 378. Cladis, P. and M. Kleman, J. Physique 33 (1972) 591. de Gennes, P. G., The Physics of Liquid Crystals (Oxford University Press, 1974). Doring, W., J. Appl. Phys. 39 (1968) 1006. Fe1dtkeller, E., Z. angew. Physik 17 (1964) 121; 19 (1965) 530. Frank, F. c., Disc. Farad. Soc. 2 (1933) 883; Phil. Mag. 42 (1951) 809.
32
J. Friedel
CHAPTER 1
Friedel, G., Ann. Physique 18 (1922) 273. Friedel, J., Dislocations (Pergamon Press, London, 1964). Friedel, J. and P. G. de Gennes, Comptes Rendus 268 (1969) 257. Friedel, J. and M. Kleman, J. Physique 30 (1969) C4; Nat. Bur. Stand. (DS) Spec. Publ. 317 (1969) 607. Kleman, M., Adv. Liq. Cryst. 1 (1975) 267. Kleman, M., Points, Lignes, Parois. Ed. de Physique, Orsay (1977). Kleman, M., L. Michel and G. Toulouse, J. Physique 38 (1977) 195. Kroner, E., Kontinuums theorie der Versetzungen (Springer, Berlin, 1958). Lehmann, 0., Fliissige Kristalle (Engelman, Leipzig, 1904). Meyer, R. B., Phil. Mag. 27 (1973) 405. Nabarro, F. R. N., Theory of Crystal Dislocations (Clarendon Press, Oxford, 1967). Nabarro, F. R. N., J. Physique 33 (1972) 1089. Neel, L., J. Phys. Radium 17 (1956) 250. Rault, J., J. Physique 33 (1972) 383. Toulouse, G. and M. Kleman, J. Physique Lettres 37 (1976) L149. Volterra, V., Ann. Ecole Normale Sup. Paris (3),24 (1907) 400. Weingarten, G., R.C. Accad. Lincei (5), 10 (1901) 57.
Crystal Dislocations and the Theory of Elasticity A. M. KOSEVICH Physico-Technical Institute of Low Temperatures Lenin's Prospect 47, Kharkov 86, USSR
References for sects. 2-6 Aerts, E., P. Delavignette and S. Amelinckx, J. Appl. Phys. 33 (1962) 3078. Amelinckx, S. and P. Delavignette, J. Appl. Phys. 44 (1962) 1459. Bordoni, P. G., Ricerca Sci. 19 (1949) 851. Cottrell, A. H., Phil. Mag. 43 (1952) 645. Dehlinger, D., Ann. Physik (5), 2 (1929) 749. Frank, F. c., Proc. Phys. Soc. A62 (1949) 202. Frenkel, J. and T. Kontorowa, J. Phys. Chern. Moscow 1 (1939) 137. Friedel, J., Comments on Solid State Physics 1 (1968) 24; Revista del Nuovo Cimento 1 (1970) 110; J. Less-common Metals 28 (1972) 241; in Physics 50 years later, IDPAP 1972, Nat. Ac. Sci. Washington (1973) 193. Heidenreich, R. D. and W. Shockley, Strength of Solids, Bristol Conf. 1947 (Phys. Soc. London, 1948). Mott, N. F. and F. R. N. Nabarro, Strength of Solids, Bristol Conference 1947 (Physical Society, London, 1948). Peierls, R., Proc. Phys. Soc. 52 (1940) 321. Schoeck, G. and A. Seeger, Acta Met. 7 (1959) 469. Seeger, A., Phil. Mag. 1 (1956) 651. Shockley, W., Trans. AI ME 194 (1952) 829. Shockley, W., Phys. Rev. 91 (195,3) 228.
© North-Holland Publishing Company, 1979
Dislocations in Solids Edited by F. R. N. Nabarro
35
Crystal dislocations and the theory of elasticity 8.3. The effective mass of a dislocation 107 8.4. Dislocation damping in a medium having dispersion of the elastic moduli 8.5. The string model
Contents
114
9. Dislocations and point defects 116 9.1. Elastic interaction of dislocations with point defects 116 9.2. Dynamical retardation of a dislocation by heavy impurities
1. Introduction 37 2. Elementary properties of dislocations 2.1. Edge and screw dislocations
9.3. Speed of climb of an edge dislocation
9.4. The climb of a helical dislocation 125 9.5. The formation and the growth of prismatic dislocation loops
38
38
2.2. A dislocation cannot end within the crystal
Addendum (1976)
40
References
2.3. Dislocation loops and plastic strain 41 2.4. Partial dislocations and stacking faults
44
3. Elastic deformations in the presence of a single dislocation 3.1. The displacement field around a dislocation loop
46
46
3.2. The strain and stress field of the straight edge dislocation
49
3.3. Deformations near a screw dislocation and the symmetry of a medium
51
3.4. The elastic energy of the straight dislocation and the problem of thermodynamical equilibrium 4. The movement of dislocations and plastic deformation of the crystal 4.1. Conservative motion (glide) 55 4.2. Non-conservative motion (climb)
55
58
4.3. The relation of the dislocation motion with plastic deformation
59
5. Interaction of dislocations with an elastic field 62 5.1. The action of a stress field on a dislocation 62 5.2. Forces between straight dislocations
66
5.3. Polygonization and a dislocation model of grain boundaries 5.4. Planar dislocation pile-ups
70
5.5. The Peierls-Nabarro force
74
68
5.6. Dislocation sources 77 5.7. The dislocation model of the twin
81
6. Systems of stationary dislocations in a crystal
85
6.1. Continuous distributions of dislocations
85
6.2. Dislocation polarization of the deformed crystal 88 6.3. Kroner's stress function for an isotropic medium 90 6.4. Interaction between dislocation loops 6.5. The self-energy of a dislocation loop
91 92
7. Dynamics of a crystal with dislocations
94
7.1. The dislocation flux density tensor
94
7.2. The elastic field of moving dislocations
98
7.3. The stress field in the linear approximation of the dislocation velocity 7.4. The radiation field of moving dislocations 102 8. Equation of motion of a dislocation
103
8.1. The field nature of the equation of motion of a dislocation 8.2. The explicit form of the equation of motion of a dislocation
103 104
101
53
138
132
119
121 128
109
1. Introduction
-:
concept of a dislocation in a crystal, together with the different dislocation representations and dislocation models associated with this concept, has been used most extensively to give an interpretation of many different physical phenomena in solids. The great popularity of the dislocation concept among physicists, who discuss "from a unified point of view" a tremendous amount of experimental data, is apparently due to a considerable degree to the fact that the concept of dislocation is very broad, and admits of many, varied, microscopic models of the structure and properties of this singularity in the crystal. The latter makes it very easy to adapt dislocation models in a crystal of any symmetry to the description ofmany phenomena which at first glance do not have a common physical nature. However, the greater number ofthe significant physical properties of the dislocation are not connected with their microscopic models, and can be described phenomenologically within the framework of macroscopic elasticity theory, to the same degree that elasticity theory is capable of describing the propagation of sound waves of not too short a wavelength in a crystalline body. A dislocation theory based on the notion of a continuous medium and founded on elasticity theory is sometimes called the continuum theory of dislocations. This theory has at present been well developed and can be formulated and expounded in the same way as other branches of theoretical physics. In particular, there exists a complete system of equations which relates, for the general case, the elastic fields with the distributions and fluxes of the dislocations. There exist rigorous equations for obtaining the plastic deformation of a body from the known dislocation motion. The equations of motion of the dislocations under the action of specified forces are obtained. The present chapter is an attempt to explain the elementary properties of dislocations and to give an exposition ofthe principles of the continuum theory ofdislocations in the general scheme of elasticity theory. It provides a description of dislocation properties that do not depend on microscopic models. The task facing the author of the present chapter is very hard since there is a fine current monograph by F. R. N. Nabarro on the theory of dislocations [lJ where these problems are discussed fairly completely. However, the author hopes to avoid trivial repetition by the choice of problems to be discussed. It is not our purpose to review the application of dislocation theory to concrete problems of the plasticity and strength of solids since this is covered in many of the following chapters.
38
A. M. Kosevich
Ch.l
2. Elementary properties ofdislocations 2.1. Edge and screw dislocations There exist many and varied microscopic models for dislocations of different types in crystals. The simplest model seems to be that where the dislocation line is the edge of the "extra" half plane inserted into the crystal. Figure 1 shows the most generally used atomic diagram of this model, where the added half-plane is the upper half of the y-z-plane. The edge of the "extra" half-plane (z-axis in fig. 1) is then called the edge dislocation. The dislocation is a linear defect of the lattice. The distortion of a regular crystal structure occurs only in the immediate neighbourhood of some line (the dislocation axis) and the region of the irregularity extending along the dislocation axis has a cross section with dimensions equal to a few lattice periods. If the dislocation is surrounded by a tube with a radius of the order of magnitude of the lattice period, then the crystal outside the tube can be considered as perfect and subjected only to elastic deformations. The crystal planes fit together in an almost regular manner outside this tube whereas inside the tube the atoms are essentially displaced from their equilibrium positions in the perfect crystal and they form here a certain structure known as a dislocation core. In fig. I the atoms of the dislocation core are conventionally situated along the contour of the shaded pentagon.
Fig. 1 A model of the atomic positions near an edge dislocation along the z-axis.
§2.1
Crystal dislocations and the theory of elasticity
the elastic displacement vector II receives a certain finite increment b which is equal to one of the lattice vectors in magnitude and direction. This property may be written as (1)
The direction along the contour is that of a right-hand screw relative to the chosen direction along the dislocation line I, that is, relative to the unit vector t tangent to the dislocation line. The dislocation line itself is a line of singularities of the elastic field.
Fig. 2 A dislocation line I and a right-hand circuit s, which encircles this line.
The vector b is called the Burgers vector of the dislocation. It is evident that possible Burgers vector values are determined by the crystallographic structure of the body considered and they correspond, as a rule, to a finite number of the vectors of the chosen lattice. As regards the dislocation line I, it may be considered in the macroscopic treatment as a smooth curve. The edge dislocation is represented by the line 1along which the vectors t and bare perpendicular. On diagrams it is usually represented by the symbol 1- where the vertical stroke points to the side from which the "extra" half-plane was inserted. In the representation given by fig. 1 the edge dislocations with opposite directions of b differ in that the "extra" crystal half-plane lies above or below the z-x-plane. Such dislocations are said to have opposite signs.
o To see the deformation far from the dislocation, we consider a closed circuit of lattice points which encircles the origin in the x-y-plane, and follow this circuit around the dislocation core. If the displacement of each point from its position in the perfect crystal is denoted by the vector II, the total increment of this vector around the circuit will not be zero but will equal one lattice period in the x-direction. It is this singularity of the dislocation deformation that may be considered as the primary one in the macroscopic definition of the dislocation in the crystal. The majority of essential physical properties of the dislocation are not associated with their microscopic models and may be described phenomenologically within the framework of the elasticity theory on the basis of this definition. Thus, the dislocation in the crystal is a singular line 1having the following properties: after a passage round any closed contour that encircles the dislocation line 1 (fig. 2),
39
0' Fig. 3 A part of the crystal with a screw dislocation along the line 00'.
A. M. Kosevich
40
Crystal dislocations and the theory of elasticity
Ch.1
41
If the vectors t and b are parallel, then the corresponding dislocation is called a screw dislocation. The presence of a straight screw dislocation in the crystal transforms the crystal planes into a helicoidal surface, Figure 3 shows the arrangement of atomic planes for the case of a screw dislocation whose axis coincides with the line 00'.
D[:001)°4
Fig. 5 A dislocation line I which ends in the medium at P. The end of the dislocation is surrounded by a cap 17 spanning the contour s.
8
I
/ //
V/ c
Fig. 4 A dislocation loop consisting of a screw type segment AB, a mixed type segment BC, an edge type segment CD and a segment of helical dislocation DA.
If the dislocation segment is neither perpendicular nor parallel to the Burgers vector, it is called a mixed type segment. The dislocation segments of edge, screw and mixed types may lie continuously along any curve forming a single dislocation line or a dislocation loop. Figure 4 shows schematically the dislocation loop ABCDA consisting of a screw type segment AB, a mixed type segment Be (450 dislocation), an edge type segment CD and the segment of the helical dislocation DA.
Let us assume that the dislocation line I 1 with the Burgers vector b, divides at a point A (fig. 6) into two dislocation lines I 2 and I 3 with the Burgers vectors h2 and h 3 , respectively. In this case the dislocations b 1 , h2 and h 3 are said to form a node. Making use of the definition eq. (1), we first choose the contour s near the point M 1 (fig. 6a) and then near the point M 2 . Since the total Burgers vector remains constant along the dislocation, we have b, = h 2 + h 3 • It is often convenient to use a new sign convention near the node. Let us take such a direction of a circuit S ds for each dislocation that it appears to be right-handed when looking outwards from the node (fig. 6b). Then the three Burgers vectors satisfy the symmetrical relation + h 2 + h 3 = O. More than three dislocations can meet at a node.
2.2. A dislocation cannot end within the crystal It is evident that the dislocation line cannot simply terminate within the crystal. It
must either reach the surface of the crystal at both ends or (as usually happens in actual cases) form a closed loop. In fact, if the dislocation line I ends at a certain point P in the medium (fig. 5), it is possible to imagine a surfaceZ, which spans the contour s, surrounds the end of the dislocation, and never crosses the line of singularities I. Then the line integral in the left part of eq. (1) could be transformed into the integral over the surface E*, duo j" . j" Ids = a dx, = j"-d s
2
aa au. 1
ckll1l
x,
Xl
x l1l
dE k ,
(2)
where Cikl is the antisymmetric unit tensor. The surface integral in eq. (2) is identically equal to zero, because the tensor Cikl is antisymmetrical. Since this result is in contradiction with the condition of eq. (1), the dislocation line cannot break suddenly withinthe crystal. It follows from this property of the dislocation that the Burgers vector is necessarily constant along the dislocation line. However, this statement should be made more accurate for the case when the dislocation line divides into several separate branches.
* The transformation of eq. (2) is made dl7l8 lk/
%x/, where
8 lkl
is
+ 1 if (i,
according to Stokes' theorem by replacing dx, by the operator k, I) is an even permutation of (123) and zero otherwise.
Fig.6
Three dislocations hI> bz and h 3 form a node. (a) A sign convention common for all dislocations. (b) A new sign convention near the node.
A stable array of dislocations in the crystal normally contains many nodes, so that the dislocations form a network. There are two- and three-dimensional dislocation networks. If only triple nodes are possible, the corresponding network must be topologically two-dimensional. But such a network can be distorted to a great extent and can be woven through its own parts. 2.3. Dislocation loops and plastic strain The condition of eq. (1) signifies from the mathematical point of view that in the presence of a dislocation the displacement vector is not a single-valued function of the coordinates, but receives a certain increment in a passage round the dislocation line. Physically, ofcourse, there is no ambiguity: the increment b denotes an additional displacement of the lattice points through one translational period of the crystal and this does not affect the lattice itself. In particular, the stress tensor Pik» which character-
A. M. Koseuich
42
Ch.l
izes the elastic state of the crystal is a single-valued and continuous function of the coordinates. The strain tensor ei k , which is usually determined as (3)
is also a single-valued and continuous function of the coordinates". Instead of the ambiguous vector of elastic displacement in the crystal with a single dislocation, we may always determine a single-valued vector u assuming that the function u(r) undergoes a uniform discontinuity b on some surface. For illustration, we consider a simple mechanism of the formation of an edge dislocation in the crystal. Assume that some shear occurs in the crystal and the corresponding displacement direction is shown in fig. 7 by arrows. As a result of this shear a part of the crystal
Crystal dislocations and the theory of elasticity
§2.3
Thus, we see that the function u(r) really has the fixed discontinuity b on some surface I~, spa~ni~g the dislocation loop. The surface Is may be chosen arbitrarily and the discontinuity of the vector u is found from «: - u" = h,
(4)
where u+ and u" are the values of u(r) on the upper and lower sides of the surface I respectively. The direction "upwards" (a positive one) is determined by the direction of the normal 11 to the surface Is (the relation ofthis direction with that ofthe vector tis shown in fig. 2).
I I
-
. Slip T
T
43
~
direction
'- - - -
A
A Fig. 8 A picture of the glide associated with the formation of the dislocation line AB. The crystal has slipped over the shaded portion of the glide plane.
Fig. 7 A model of the formation of an edge dislocation in the crystal.
above the plane TT' starts to slip over the lower part of the crystal and the upper part of the left side of the crystal (above T) is translated through a distance b to the right. If the glide has started at T and not yet reached the other end T' of the slip plane, then there is a region AA' on the slip plane over which n atom rows above the plane are associated with n - 1 atom rows below. This region contains the edge dislocation. All the atoms above the part TA of the slip plane are shifted by b relative to the atoms below this plane. Denote the quantity of Ux by u; and u; for the upper and lower sides of the slip plane, respectively. Then, U x = b in the region TA and u; = 0 in the region A'T'. Therefore the edge dislocation is the boundary of that part of the slip plane where the displacement vector undergoes a discontinuity. Its Burgers vector determines the magnitude of this discontinuity and the glide direction. Figure 8 shows a three-dimensional picture of the glide which is associated with the formation of the dislocation line AB. The right part of the crystal in fig. 8 corresponds to fig. 7. The displacement vector undergoes a discontinuity b on the shaded part of the slip plane.
o; -
u; -
* It should be noted that the representation of the ei k as the derivatives eq. (3) is not meaningful on the dislocation line, which is a line of singularities.
This fact allows one to give another formal definition of the dislocation, i.e. to describe it as a line I, which is spanned by the surface Is over which the vector u has a specified discontinuity given by eq. (4). In some cases this definition appears to be preferable to the first one of eq. (1). . I~ the strain tensor for the crystal with a dislocation is calculated by using eq. (3), r.e. III the presence of the discontinuity of eq. (4) along the surface I , it has a deltafunction singularity on this surface. The corresponding singular part of the tensor eik is given by e~~)
= i(nib k + nkbJ £5((),
(5)
where ( is a coordinate taken from the surface Is along the normal 11. Since there is no actual physical singularity in the space around the dislocation, the stress tensor Ps« must be a continuous function everywhere. According to Hooke's law, the tensor Pik is related with the elastic strain tensor e~ by: Pik
=
C ik1m erm'
(6)
Both tensorsrij and e~ should be continuous on the surface L s ' However, as mentioned above, the strain tensor has a singularity on this surface, which should not appear in the Hooke's law expression of eq. (6). Therefore, the total strain tensor eT in the crystal with a dislocation has the form of a sum ik (7)
44
A. M. Koseoich
Ch.l
The second item in the right-hand part of eq. (7), namely efk' is not directly related with elastic stresses. Such a strain is called plastic. Thus, the crystal with a dislocation may be considered to have a plastic strain efk = e~~), which is determined by the relation of eq. (5). It is of interest to note that the discontinuity surface 1:s may be chosen arbitrarily in a crystal with a single stationary dislocation. This signifies that the plastic strain is not a function of the state of the body, but depends on the method of formation of the dislocation or on the dislocation motion.
Crystal dislocations and the theory ofelasticity
§2.4
45
plane, and points «, {3, y, etc. determine atom positions in the succeeding atom layer. Then, vectors AB, AC, BC or IXP, lXy, py, i.e. joins of the nearest letters from the same alphabet, give the possible Burgers vectors of complete dislocations. The vectors yB and others which join the nearest letters from different alphabets give Burgers vectors of partial dislocations which are called Shockley partials. AB
2.4. Partial dislocations and stacking faults Dislocations are linear defects; there also exist in the crystal defects in which the regular structure is interrupted throughout a region near a given surface. In order to understand the physical nature of such defects, we consider a crystal to be made by stacking atomic layers. A displacement of one layer over its neighbour by a lattice vector lying in its plane does not alter the structure of the crystal. However, a displacement which is not a lattice vector produces a stacking fault. Such displacements, when combined with a small displacement normal to the stacking plane, can produce a configuration in stable mechanical equilibrium. Then the stacking faults become . stable. A well-known example of such defects is a narrow twinning band in the crystal.
x
Aa
IT
aB
Fig. lOAn extended dislocation. The complete dislocation AB splits into two partials AIX and IXB at the point X.
Now, consider a dislocation node, where one complete and two Shockley partial dislocations meet (fig. 10). All three dislocation lines and their Burgers vectors lie in the same crystal plane which is the plane of the figure. The complete dislocation AB splits into two partials AIX and IXB in a point x according to the scheme AB = AIX Fig. 9 Possible Burgers vectors in the close-packed structure. The closed circles represent atoms on a close-packed plane, and the open circles represent atoms on the succeeding close-packed plane.
The stacking fault can be macroscopically described as a surface of discontinuity over which the displacement vector u is discontinuous, but the stresses Pu. are continuous. If the discontinuity 0 is the same everywhere on the surface the resulting strain is just the same as that due to a dislocation along the edge of the surface. The only difference is that the vector 0 does not equal a lattice vector. The dislocation forming the boundary of the stacking fault is called a partial dislocation". The position of the surface 1:s discussed above in sect. 2.3, is no longer arbitrary, it must coincide with the actual stacking fault. Such a surface of discontinuity involves a certain additional energy which may be described by means of an appropriate surface-tension coefficient. The simplest types of partial dislocations exist in crystals with close-packed structures. Let points A, B, C, etc. in fig. 9 determine atom positions on a close-packed * A common dislocation where the vector b is a lattice vector is called a perfect dislocation or a complete dislocation.
+ IXB.
(8)
The region I of the slip plane where shear by a lattice vector occurs, and the region II where there is no displacement, are demarcated by the complete dislocation. The passage of the first partial dislocation along the slip plane causes a stacking fault which is healed by the passage of the second partial. Thus, the stacking fault in the region III is bounded by two partial dislocations. The configuration which arises of two partial dislocations separated by the stacking fault is called an extended dislocation. When two dislocations with Burgers vectors 0 1 and O2 combine to form a single dislocation with the Burgers vector 0 3 = 0 1 + O2 we have a dislocation reaction. The relation of eq. (8) illustrates a reaction of dissociation. A Shockley partial has its Burgers vector lying in the stacking fault plane. This dislocation is schematically drawn in fig. 11. A twinning dislocation is of the same type. However, there exist partial dislocations which have their Burgers vectors not in the stacking fault plane. Examples of such dislocations are shown in fig. I2a and b. The Burgers vectors are here perpendicular to the stacking fault plane. Such dislocations in crystals with a close-packed structure are called Frank dislocations.
46
A. M. Koseoich
Ch.l
Crystal dislocations and the theory of elasticity
§3.1
47
Thus, the problem of finding the many-valued function u(r) is equivalent to that of finding a single-valued but discontinuous function in the presence of the body forces given by eqs. (5) and (9). We can now use the formula
u,(r)
f
~ ~ik(r
r)f'f'(r) dr.
We substitute eq. (9) and integrate by parts; the integration with the delta function is then trivial, giving: uJr) = -Cjklmbm
Fig. 11 Shockley mobile partial dislocation.
rJE,.nl -00x ~i/r -
r') dE'.
(10)
k
Fig. 12 Examples of a sessile partial dislocation. (a) The positive Frank partial. (b) The negative Frank partial.
This solves the problem. In principle, eq. (10) allows us to obtain elastic displacements in the crystal for an arbitrary form of the dislocation loop. It should be noted, however, that the general formula of eq. (10) is very complicated and the calculation of the displacement field in an anisotropic medium even for simple dislocation line configurations is rather cumbersome and tiresome. In the case of a straight dislocation, the direct solution of the equilibrium equation under the condition of eq. (1) appears to be a more simple procedure. Equation (10) has a simple and evident form for the isotropic case. The elastic modulus tensor Cik1min the isotropic medium reduces to two Lame's elastic constants }c and fl (fl is the modulus of rigidity): Cik1m = A 6ik6lm + fl(6 a 6km + 6im 6kl ),
(11)
and the Green's tensor is
3. Elastic deformations in the presence ofa single dislocation
1 (26 ik }o + 02r ) ~ik(r) = 8nfl -r- - A + 2fl oX oX . i k
3.1. The displacement field around a dislocation loop The displacement field u(r) around a single dislocation can be expressed in a general form if we know the Green's tensor ~ik(r) of equilibrium equations for the anisotropic medium considered, i.e. the function which determines the displacement component U i produced in an infinite medium by a unit force applied at the origin along the xk-axis. This can be easily found by using the following formal device. Instead of seeking many-valued solutions of the equilibrium equations we shall regard u(r) as a single-valued function which undergoes a discontinuity given by eq. (4) on the surface spanning the dislocation loop I. We bear in mind that the strain tensor of eq. (3) has the singularity given by eq. (5) on the surface Es ' The strain tensor e~~) is formally related to a stress tensor p~~) = ciklmel~, which also has a singularity on the surface Es ' In order to eliminate this we must introduce fictitious body forces distributed over the surface E s with a certain density j(8). The equilibrium equations in the presence of the body forces are OPik/OXk + j~S) = O. Hence, it is clear that we must put oel~
-Cik1m ox
k'
(9)
(12)
After substituting eqs. (11) and (12) in eq. (10) and using Stokes' theorem, eq. (10) reduces to the following expression for the displacement of u in the point x: Q
u(x) = b4n Here
Q
+
1 4n
fb- rx -dl + grad lj/.
(13)
is the solid angle which the dislocation loop subtends at x (fig. 13) and
lj/ =
), + 4n(A
fl
+ 2fl)
f
dl b x (x - l) -, r
where dl is an element of the dislocation line, r = Ix - II and both integrals are taken . once round the dislocation line. The representation of eq. (13) for the displacement vector u in terms of the solid angle Q and contour integrals along the line I was derived by Burgers [2J. The line integrals are necessarily single-valued functions of x. But the vector u must be manyvalued for circuits linking the singular line, and all its multiplicity is due to the solid angle Q which is a multiple-valued quantity with the residue 4n.
A. M. Kosevich
48
Ch.l
Leibfried [3J has derived a similar formula for the dislocation in an anisotropic medium. The corresponding solution has the form: Q
u
= b- + u* 4n
(14)
'
where u* may be written as a certain line integral along the dislocation loop. However, the explicit expression for u* in an anisotropic medium can be obtained only for special cases. The problem can be solved when the Green's tensor C§ik is obtainable.
§3.1
Crystal dislocations and the theory of elasticity
49
The axial vector S has components equal to the areas bounded by the projections of the loop I on planes perpendicular to the corresponding coordinate axes. The tensor dik may be called the dislocation moment tensor. The components of the tensor C§ik decrease in inverse proportion to the distance 2 C§ik ex l/r, hence, it follows from eq. (15) that U i ex l/r . The corresponding strain field decreases with the distance according to the law of Pn. ex l/r 3. In an isotropic medium we can make use of eqs. (11) and (12); eq. (15) is then reduced to (17) where a = p/(A
x Fig. 13 The solid angle
Q
subtended at X by the surface L s ' which is bounded by the dislocation loop I.
The tensor C§ik for an anisotropic medium was derived by Lifshitz and Rozentsveig [4J. However, the derived expression appeared, in general, very complicated and the tensor C§ik was obtained in an explicit form [4J only for a hexagonal medium. The problem of obtaining the displacement field for an arbitrary dislocation line in a cubic medium was solved by Burgers [5]. If the departure from isotropy is small, the stress field of an arbitrary dislocation line in a medium of any symmetry can be found [3J by a perturbation method. Using eq. (13), the strain tensor around the dislocation in an isotropic medium can be calculated. The strain components are single-valued and thus eik can be represented by line integrals. Peach and Koehler [6J gave the corresponding expressions. These line integrals can be calculated explicitly if the dislocation line is a plane curve of the second degree (quadratic curve) [7]; in this case the integration leads to elliptic integrals. The deformation of eq. (10) has its simplest form far from the closed dislocation loop. If we imagine the loop to be situated near the origin, then at distances r, large compared with the linear dimensions of the loop, we have (15) where (16)
+ 2p).
Note the fact that the displacement field, far from the dislocation, is determined only by the symmetric part of the tensor dik . If the dislocation loop lies entirely in the plane in which the vector b lies, it appears convenient to choose the x-axis along b, and the z-axis perpendicular to the loop plane: b, = b 6ix ' Si = S 6iz ' Then eq. (17) will give us the expressions obtained by Nabarro [8J: UX
=
4~~3[a + 3(1 -
a) ;:Jz,
3bS uy = - 45 (1 - a)xyz, nr
UZ
bS [ a + 3(1 - a) rZ2J x. = 4nr 3 2
3.2. The strain and stress field of the straight edge dislocation" If the dislocation is a straight one, it is easy to ascertain the way in which strains and elastic stresses vary with the distance from the dislocation in the general case. In cylindrical polar coordinates r, e, z (with the z-axis along the dislocation line) the deformation will depend only on z and e. The integral of eq. (1) must, in particular, be unchanged by an arbitrary change in the size of any contour in the x-y-plane which leaves the shape of the contour the same. It is clear that this is true only if all the components of the tensor oujoxk are inversely proportional to the distance: ou) oX k ex l/r. The strain tensor eik and, therefore, the stress tensor Pu. will be proportional to the same power l/r. It was mentioned above that in the case of the straight dislocation when we deal with a two-dimensional problem of elasticity theory, it is sometimes not convenient to use eq. (10). It often appears preferable to solve the equilibrium equation directly.
* See Addendum 3.
50
A. M. Kosevich
Ch.l
As an example of the calculation of elastic fields in the presence of a straight dislocation, we determine the deformation around the edge dislocation in an isotropic medium [2, 9J. The physical meaning of this and other problems relating to an isotropic medium is purely hypothetical, since actual dislocations by their nature occur only in crystals, i.e. in anisotropic media. Such problems have illustrative value, however. We take coordinates x, y, z, so that the z-axis is along the dislocation line* and the x-axis is along the Burgers vector: bx = b, by = b, = O. It is evident from the symmetry of the problem with ez z = 0 that the displacement vector u lies in the x-y-plane and is independent of z so that the problem is a two-dimensional one. Love [1 OJ derived the following representation for the general solution of the twodimensional problem of elasticity theory:
Crystal dislocations and the theory of elasticity
§3.2
51
By using eq. (22) we can find the strain tensor of the edge dislocation e ik . This tensor has the following non-zero polar components: b« sin e err = eee = - 2n -r-'
b
ere = 4n(1
v)
cos 8 r
(23)
The stress tensor has the polar components: Prr
sin 8
= Pee = - D -r- ,
cos e Pe = D--, r r
(24)
where D = J1bj2n(1 - v). The Cartesian components of the tensor P« are
OX
2J1u x = 4(1 - v)P - ox' (25)
2J1u y = 4(1 - v)P -
oX oy'
(18)
where v is Poisson's ratio, and X = x(x, y) is the stress function which is equal to X = 2yQ
+
R.
(19)
Here, P, Q and R are harmonic functions; P, Q are harmonic conjugates. We wish to have a multiple-valued displacement Ux but single-valued stresses. Thus X must be single-valued, but P must be multiple-valued. Select a suitable pair of functions P and Q by choosing them to be the real and imaginary parts of the following complex function r(Z):
, = x + iy,
f(O = -iA log"
(20)
Since we assumed ez z = 0, then pzz = v(Pxx
+ pyy) = v(Pzz' + Pee)·
The average hydrostatic pressure produced by the edge dislocation in an isotropic medium is 2 sin 8 = 3(1 + v)D - - . r
1
Po =
3Pkk
(26)
Equation (26) has a simple physical meaning. Over the z-x-plane (8 > 0), where there is an "extra" half-plane inserted in the crystal, the medium is compressed, and Po > O. Below the z-x-plane (8 < 0) we therefore expect Po < O.
where A is any real constant. If we take R = 2Ay we obtain P
= Ai),
Q = -Alogr,
X
= -2Ay(log r
-
1),
(21)
3.3. Deformations near a screw dislocation and the symmetry of a medium
where
The cyclic constant A is obtained from the condition of eq. (1) and is A = bu] 4n(1 - v). Then the displacements are given by: b [ -1 Y u=-tan x 2n x
+
1 xY], 2(1 - v) r 2 2
uy
= - 4n(1 b_ v) [ (1 - 2v) log
* In all the
r
x ] + -;:z
.
problems on straight dislocations we take the vector t in the negative z-direction.
(22)
We determine the strains and stresses of a screw dislocation in an isotropic medium. Let the z-axis again be along the dislocation line; then the Burgers vector is b; = b; = 0, b, = b. It is evident from symmetry that the displacement u is parallel to the z-axis and is independent of the coordinate z. Since the relation Pu. = 2J1e i k for i .# k holds in an isotropic medium, the equilibrium equation in the absence of the body forces can be written in the form oeikjoxk = 0 and can be reduced to a twodimensional harmonic equation for Uz : Ju = 0, J = o2jox 2 + o2joy2. (27) z
The solution of eq. (27) which satisfies eq. (1) has the form b 2n
b tan -1Y -. 2n x
u = -8 = z
(28)
52
A. M. Koseoich
Ch.l
The tensors eik and Pu.have only the following non-zero components in the cylindrical coordinates:
j1b
b ezo = 4nr
Pzo
=
P yz
=
~[y
2n
ub [ 2n
(x -
X
O)2
x (x - X
+ y2
div
(x
+
- (x
+
-
Xo
O)2
+ y2
x
X
y+ ]
+ X
y2 '
O)2
Xo
O)2
+ y2
(J
O =,
(ja
=
au
"
Aap ;;--.
ux p
The required solution of this equation which satisfies eq. (1) is [14J: aa =
b
Paz
= 2n
)'ap8pzyXy
1111/2 1 - 1 A
Aa,p'Xa,x p'
IX
'
= 1, 2,
i;
1 where 1),1 is the determinant of the tensor Aap and is the inverse of the tensor AafJ • In the last formulae we sum over repeated Greek indices from 1 to 2.
3.4. The elastic energy of the
l;ltr~i1lioll1t
dislocation and the problem of thermodynamical
The elastic energy density is equal to -iPikeik' Therefore, the elastic energy per unit length of the straight dislocation is given by the integral
] .
53
only two components of the tensor Pik are non-zero: Pxz and pyz. We define a twodimensional vector (J and a two-dimensional tensor Aik : (ja = Paz; Aap = Cazpz(IX, fJ = 1, 2). Then the equation of equilibrium takes the form
(29)
= 2nr
Thus, the deformation around the screw dislocation in the isotropic medium is a pure shear. Since the mathematical theory of screw dislocations is rather simple, we can readily obtain the expressions for the stresses of a screw dislocation which is parallel to the plane free surface of an isotropic medium. Let the y-z-plane be the surface of the body, and let the dislocation be parallel to the z-axis with coordinates x = X o ' y = O. The stress field which leaves the surface of the medium a free surface is described by the sum of the fields of the dislocation and its image in the y-z-planes each considered to lie in an infinite medium: Pxz
Crystal dislocations and the theory of elasticity
§3.3
(30)
The dependence of the stresses in eq. (30) on the distance X o is typical of any straight dislocation near the crystal surface and is very important in discussion of various boundary problems. The comparison of the displacement of the screw dislocation with that around the edge dislocation (sect. 3.2.), shows that in an isotropic medium any straight dislocation has the following property. The dislocation with the tangent vector t may be considered to consist of two independent dislocations, i.e. a pure screw dislocation, the displacements of which are parallel to t, and a pure edge dislocation, the displacements around which are perpendicular to t, It is of interest to know whether the displacement field of a straight dislocation in an anisotropic medium can be split into a pure screw component, in which all displacements are parallel to the dislocation line, and a pure edge component, in which all displacements are perpendicular to this line. It appears that this is possible if the dislocation line is a two-fold rotation axis of the medium or if the dislocation line is perpendicular to a symmetry plane of the crystal. The elastic field of the straight dislocation in an infinite anisotropic medium was studied by many authors {Ll ] by using different methods. These methods were put into a systematic form [12J and were later extended for the case of a straight dislocation which is parallel to a plane interface between two anisotropic media [13]. The reader may find a detailed discussion of the corresponding problems in subsequent chapters. We confine ourselves to a simple example where the stresses are determined in an anisotropic medium around the screw dislocation which is perpendicular to a plane of symmetry of the crystal. We take the coordinates x, y, z in the usual manner and write Uz = u(x, y). Since the x-y-plane is a plane of symmetry, all components of the tensor Ciklm which contain the suffix z an odd number of times are zero. Thus,
U =
i f P;keik dx dy.
(31)
For a screw dislocation the integral of eq. (31) is: 2
Us
1 ="2
f 2pzoezo2nr dr
=
j1b fdr -, 4n r
(32)
where the integration over r should be made, in general, within the limits (0, 00). But the integral of eq. (32) diverges logarithmically at both limits. The divergence at the lower limit does not occur in real crystals because Hooke's law breaks down in the core of the dislocation. According to the existing atomic dislocation models, the lower limit r 0 should be of the order of the magnitude of the displacement that gives rise to the dislocation, that is ro ....., b. This estimate is natural from the point of view of elasticity theory, since it places a lower limit on the distance over which the dislocation theory considered here is valid*. Substituting the lower limit r0 in the integral of eq. (32) we omit the energy of the dislocation core Uo We easily estimate the maximum value of the energy Uo- The relative atomic displacements in the dislocation core with the cross section r~ ....., b? are of the order of magnitude of unity. Therefore the energy per unit length of the dislocation core is estimated as (33) The upper limit is determined by a quantity R of the order of the dislocation length or of the crystal size. We have then:
j1b 2 R Us = 4 log-· n ro
* We may call r 0
the radius of the dislocation core.
(34)
A. M. Koseoich
54
Ch. I
It is seen by comparison of eqs. (34)and (33) that eq. (34) determines the essential part of the dislocation energy only under the condition 10g(R/ro) » 1. One sometimes says that eq, (34) determines the dislocation energy with logarithmic accuracy. For the edge dislocation the integral of cq. (31) is
UE
~t
f
(p"e"
+ Po.eoe +
2p,.e,.)r dr dO
fR dr f21'C .
ub?
4n 2 (1 - v)
ro
r
sm
0
2
ede =
2
f1b log 4n(1 - v)
R -. ro
(35)
It is natural that the energy per unit length of the edge dislocation has the same order of magnitude as that of the screw dislocation. It is easy to estimate the energy per unit length for any slightly curved dislocation line with a radius of curvature R c which satisfies the condition 10g(Rc/r o) » 1. It is evident that the energy per unit length of such a dislocation has the order of the magnitude (see sect. 6.4.) V
r'V
ub?
R
4n
t
-log~·
§4.l
Crystal dislocations and the theory of elasticity
The movement of dislocations and plastic deformation of the crystal Conservative motion (glide) We refer again to the definition of the dislocation as a line which is the edge of a surface of discontinuity (eq. (4)). We used this definition earlier in a certain formal procedure which allows us to solve a number of static problems of elasticity theory in the medium with dislocations. Parallel to that we suggested a possible process of the formation of the dislocation by relative translation of atomic layers on the positive and negative sides of the surface 1:s through a distance b. However, some difficulties of a physical character arise from this manner of formation of the dislocation. In fact, when the requirement of eq. (4) is formulated we assume that the crystal remains continuous over the surface E s ' and, in particular, that the atomic spacings remain unchanged (with an accuracy up to elastic deformations). It is easy to understand that the actual discontinuity given by eq. (4) leads to failure of the crystal continuity.
(36)
«
Since unit length of any dislocation element has the energy of eq. (36), then there is a line tension T D of the dislocation, which is weakly dependent on the point on the dislocation line and may be estimated as TD
r'V
ub?
R
4n
ro
55
-log~'
n
(37)
It should be noted, however, that the theoretical "large parameter" 10g(R/r0) » 1 104 - 106 , although it is is not, in fact, so large. Really, if we take the ratio R/r o often smaller, then we come to the conclusion that log (R/r o) does not differ considerably from 4n. Therefore, the energy per unit length of the dislocation may be taken in a crude approximation as*
Fig. 14 A cut along the surface J:s ' The right cut surface undergoes a rigid displacement b. The closed circles represent atoms and the open circles represent vacant lattice sites.
r'V
(38)
Then the energy of an atomic length of the dislocation is approximately equal to
w = Ub ~ ub", 10- 2 3 cm ' and u 1011 erg/em" then w 10- 12 erg '" Since we have usually b 3 1 eV. This is a very large energy for each atom in the core of the dislocation. It appears [15, 16J that the increase of entropy in the crystal with a macroscopic dislocation loop cannot compensate such a large elastic energy. It follows that the free energy of the crystal with the dislocation exceeds that of the perfect crystal. Therefore, any dislocation which has a macroscopic length is thermodynamically unstable. Hence, the dislocated crystal can be in a state of mechanical equilibrium, but this state is a thermodynamically metastable one. r'V
* A similar estimate is valid
r'V
also in an anisotropic medium.
Really, the diagram (fig. 14) of the atomic arrangement along the part of the surface (under the condition nb > 0) shows that a macroscopic number of vacant lattice sites (the open circles in fig. 14) is formed after the relative translation of the atomic layers. The supply of some "extra atomic material" is required to fill these vacant sites and to ensure continuity of the medium. The additional volume associated with this material is equal to
b17 = nb b1: = b bE s
(39)
r'V
for each element bE of the surface of discontinuity. Therefore, the formulation of the condition of eq. (4) implies that we scrape away any surplus material where the atomic layers overlap and fill in any remaining gaps with the material supplied. But there are no mechanisms of automatic extraction or supply of the macroscopic quantity of the material inside the bulk of the crystal. Thus, a purely mechanical way of forming the dislocation is impossible by real displacement of the atomic layers on two sides of an arbitrary surface without causing discontinuities of the physical quantities on this surface. However, it follows from eq. (39) that for any dislocation in the crystal it is possible to find a surface 1:g spanning the dislocation loop in each point of which nb = O. It
Ch.l
A. M. Koseoich
56
is clear that this is a cylindrical surface with generators parallel to the vector band with a directrix along the dislocation line I (fig. 15). The displacement through a distance b over this surface is a sideways shift and does not break the continuity of the crystal. Such a surface is called the dislocation glide surface and is the envelope ofa family of the glide planes of all dislocation elements. By glide plane of a dislocation element is meant the plane tangent to the corresponding line element, a plane specified by the vectors t and b. Possible systems of glide planes in an anisotropic medium are determined by the structure of the corresponding crystal lattice. b
(a)
( b)
Fig. 15 Glide surfaces J.: g of dislocation loops. (a) The dislocation loop I may be reduced to a point by slip. (b) The dislocation I can make only a prismatic glide over the cylindrical surface with axis parallel to the Burgers vector b.
Thus, the displacement through a distance b over 1:g is "harmless" for the crystal, since lattice periods remain unchanged near this surface. In reality, one can shift the parts of the lattice on either side of the surface 1:9 to a distance of the lattice period b and form a dislocation. The physical peculiarity of the glide plane lies also in the fact that the dislocation can move comparatively easily in this plane. The latter follows directly from the microscopic picture of the dislocation defect and is readily demonstrated by the diagram with an extra half plane sketched in fig. 1. Let the edge dislocation be formed by the shift by a distance b along the glide plane. The trace of the slip plane coincides with the crystallographic direction TT' in fig. 16. We consider configurations near
§4.l
Crystal dislocations and the theory of elasticity
57
the dislocation core both for the first case, when the extra crystal half-plane is in the position MM ' (the atoms are shown by filled circles) and for the second case when the atomic layer in the position NN' plays the role of an extra half-plane of the crystal atoms are shown by open circles). Though the transition from the first atomic configuration to the second one is connected with the displacement of the dislocation by a single atomic spacing to the right of the glide plane, the displacements of individual atoms which make this transition possible turn out to be small as compared with b. This means that such a collective atomic rearrangement, which ensures the motion of the dislocation, can occur under the effect of comparatively small forces. The comparison between these forces and macroscopic stresses shows that the corresponding shear stress as which is necessary to start the dislocation motion is less than the rigidity modulus fl by a factor of 102 - 104 • The small value of the parameter asfu is the decisive physical factor which allows the use ofthe common linear theory ofelasticity for the description of the mechanical processes accompanied by the motion of dislocations. Thus, the dislocation can move rather easily in its glide plane in a purely mechanical manner. Such a motion of the dislocation is usually called glide or conservative motion. Dislocation loops may be divided into dislocations of two types according to their position on the glide surface. The dislocation loop of the first type (fig; 15a) may be made infinitely small by slip, i.e. it may be reduced to a point on the surface 1:g • The slip of the dislocation of the second type on the surface 1:9 (fig. 15b) would never make the dislocation loop infinitely small. In this case the motion of the dislocation on the glide surface is called prismatic glide. The dislocation loop of the second type has the smallest dimensions when it lies in the plane perpendicular to the vector b. The plane dislocation loop with its Burgers vector perpendicular to its plane is called a prismatic dislocation. However, a situation may arise when the dislocation can move by a slip into another glide surface (or to another glide plane if we have a plane dislocation loop). We consider a part of the dislocation line which lies in its glide plane (fig. 17a) and assume that it has a screw-type segment. Note that the plane dislocation loop with a smooth line (without breaks) has always a screw-type segment. The screw dislocation (t II b)
Ullb)
bF
GI:~I plane (a)
Fig. 16 The edge dislocation with the Burgers vector b undergoes a slip displacement along the glide plane TT'. An initial position of the "extra" half-plane is MM', and atoms are represented by the closed circles. A final position of the "extra" half-plane is NN', and atoms are represented by the open circles.
Fig. 17 Cross slip. (a) Primary glide plane of the dislocation line having a screw segment with t II b. (b) The screw segment bl o moves out of the primary slip plane into the cross-slip plane which also contains the Burgers vector b. A new position of the dislocation segment is b/ l .
A. M. Kosevich
58
Ch.l
can slip in any plane which contains it. Any plane parallel to b may be considered as a glide plane of the screw segment of the dislocation loop. This plane need not coincide with the glide plane of the rest of the dislocation crossing it at a certain angle. The screw segment with a finite length Mo can now slip in a new glide plane taking the shape of the arc M1 (fig. 17b). Such a deviation of the screw-type segment of the dislocation from the old glide plane into a new one is called cross slip.
Crystal dislocations and the theory of elasticity
6N is the difference in the number of interstitial atoms and vacancies generated. point defects for which eq. (41) is written appear and disappear directly near dislocation core. Therefore, all the changes of the crystal volume may be con\,j~AJ."J.'''''''''''''' on the dislocation line in the macroscopic description of the dislocamotion. The displacement of the dislocation in the direction perpendicular the glide plane should be accompanied by a local increase of the volume, and the relative volume change is 6e2k = 6x(b x t) 6(~),
4.2. Non-conservative motion (climb) The real motion of the dislocation in the direction perpendicular to the glide plane is of quite a different physical nature. We consider the arbitrary small displacement 6x of the element of the dislocation loop dl and refer again to the definition of the dislocation based on the condition of eq. (4). Irrespective of the choice of the initial surface LS' the real displacement of the dislocation element leads to an increase of the area of this surface by 6L, where
59
(42)
6(~) is the two-dimensional delta-function and ~ is the two-dimensional vector taken from the dislocation axis in the plane perpendicular to the vector at the point considered. The rate of the displacement of the dislocation described here is limited by the diffusion processes which ensure the volume change of eq. (42). Such a motion of the dislocation is called climb or non-conservative motion.
6I = 6x x dl. Such a change of the surface area L s is accompanied by an inelastic local increase of the crystal volume which, according to eq. (39), is given by
6T = b 6I = b(6x x dl) = -(b x dl)6x.
(40)
Note that the vectors band dl specify the glide plane orientation. In the case where the displacement 6x has a component normal to the glide plane, the quantity defined by eq. (40) is non-zero. It has already been mentioned that the lack (for 6T > 0) or excess (for 6T < 0) of material cannot be compensated in a mechanical manner inside the bulk of the perfect crystal if the continuity of the medium is conserved. However, in the perfect crystal there is a certain slowly acting mechanism of the change of the density of the substance, and this mechanism does not require macroscopic disturbances of the continuity of the medium. We mean the processes of formation and diffusion migration of point defects such as interstitial atoms (which densify the substance) and vacancies (which rarefy it). Therefore, dislocation motion in the direction normal to the glide plane can occur without disturbing the continuity of the medium only under the condition that there may be a diffusion exchange of matter between the dislocation line and the bulk of the crystal. This diffusion process can compensate an inelastic increase of the volume on the dislocation axis by the same decrease of the volume in the bulk of the crystal. The latter change of the volume is associated with the creation or destruction ofthe corresponding number ofpoint defects in the immediate neighbourhood of the dislocation core. Since each atom in the crystal has the relevant volume of the elementary cell a", the quantity eq. (40) should be related with the number 16TI/a3 of the vacancies created or interstitial atoms destroyed. But, as the point defects of both types can appear or disappear, the change of their number is associated with the displacement of the dislocation line element by the formula
6N =
b x dl - - 3-
a
6x,
(41)
Fig. 18 An originally straight screw dislocation AB with the Burgers vector b transforms into a helical dislocation.
The climb of a screw dislocation presents a rather interesting problem in the theory of dislocation motion. The straight screw dislocation AB (fig. 18) cannot move by climb as any plane is its glide plane if the line AB lies in this plane. However, if the dislocation is fixed in the points A and B, then any displacement of the dislocation line results in its curving. In the process of the screw dislocation curving there arises an edge component of the Burgers vector and, hence, some dislocation segments can now climb. The joint climb and prismatic glide may lead to the formation of a socalled helical dislocation (fig. 18).
4.3. The relation of the dislocation motion with plastic deformation The elastic field ofthe dislocation changes with its movement. However, the movement of the dislocation causes not only a change in the elastic deformation but also a change in the shape of the crystal which does not involve stresses, i.e. plastic deformation.
60
A. M. Kosevich
Ch.1
Crystal dislocations and the theory of elasticity
This is clearly illustrated by fig. 19, where the passage of the edge dislocation from left to right causes the part of the crystal above the glide plane to be shifted to the right by one lattice period; since the lattice is then regular, the crystal remains unstressed. Thus, dislocation motion is one of the mechanisms of plastic deformation.
61
n
20 The dislocation line I with the tangent vector t undergoes a displacement bX and occupies the position 1'. The ~-axis lies in the plane of the vectors t and c5X.
eqs. (45) and (46) we obtain the change of plastic strain, given by Fig. 19 A model of the atomic layer positions before, during and after the passage of a dislocation across the crystal.
de~
= i(nib k + nkbJ 6(0 dec;
rl",.. nl<:>lhup
Remember that, unlike an elastic deformation which is uniquely defined by the. thermodynamic state of the body, a plastic deformation depends on the process which occurs. However, if the motion of the dislocation is known, the change of the plastic deformation is defined uniquely. In sect. 2 we gave the formal definition of the plastic strain e~k over the surface 1:s spanning the dislocation loop I. Now consider a certain point on the dislocation line I and rewrite eq. (5) for the vicinity of this point as
efk = i(nib k
+ nkbJ 6(oe(~
- ~o),
(43)
where e(x) =
{I,0, xx <> O.0;
(44)
The (-axis is along the normal vector n, and the ~-axis is along the unit vector t x n (fig. 20) and the coordinate ~ is taken from the dislocation line, whose position is ~o
=
~o)'
(47)
from the definition of eq. (44) which determines the function e(x) that its equals the delta function: e'(x) = -6(X), and thus
de = (de/d~o) d;o =
-e'(; -
~o) d~o
=
6(~ - ~o) d~o.
(48)
substituting eqs. (45), (46) and (48) in eq. (47) we have 6e~
= -i(biCklm + bkCilm)tm 6(,) 6X1 ,
(49)
6(~) is the same two-dimensional delta function as in eq. (42) and ~ is the two-drmensronat radius vector with the components ((, ~ - ~o)' see that, in fact, the change of plastic deformation is related uniquely with the parameters of the dislocation, i.e. the vectors band t. and with the value of the dislocation displacement 6x. The plastic deformation related with the motion of a single dislocation should be taken into account when one dislocation cuts the line of another. We consider two dislocations: one of them moves and the other is immobile. Let the line Ii be the original position of the first dislocation (fig. 21), 1: ~ be its glide surface and the line AB
~o(l)·
If the dislocation is immobile, the surface 1:s and hence the vector n may be taken arbitrarily. If a real displacement of the dislocation takes place, the change 61:s is determined uniquely and the corresponding normal n also becomes single-valued. Let 6x be the displacement of the dislocation which causes the dislocation line to take the position i' (fig. 20). The ;-axis lies now in the plane which is specified by t and 6x. We shall derive the formula for the change of e ~ with such a motion of the dislocation. We have 61:s = 6x x dl and
n = (6X x t)/16xl sin cP,
(45)
where cP is the angle between the vectors 6x and t (fig. 20). It is also evident that 6~o
= 16xl sin cP.
(46)
Fig. 21 The dislocation line AB with the Burgers vector b is cut by another dislocation which has the Burgers vector b1 perpendicular to the line AB and moves from a position 11 to a position I~. As a result a step AOO/C arises. This step can be resolved into a kink and a jog.
Ch. 1
A. M. Kosevich
62
be the original position of the second dislocation. As a result of the displacement by bx, the first dislocation cuts the line of the second dislocation in the point 0 and occupies the position 1'1 (fig. 21). Then points on the line of the second dislocation, separated by the glide plane of the first one, suffer a relative displacement of hi. This displacement appears as a step AOO'C in the line of the second dislocation". We can resolve the step h1 in the line of the second dislocation into three orthogonal components. The first one is parallel to the dislocation line. The second, in the glide plane of the second dislocation 'E9 and perpendicular to its line, is called a kink. The third component, normal to the glide plane of the second dislocation, is a jog (fig. 21).
Crystal dislocations and the theory of elasticity
63
dislocation is not related with the additional body forces within the crystal, = 0 and the first integral on the right of eq. (52) vanishes. In order to ""aI'...,....A'... ~.., the last two integrals we take for 'E a surface, made up of the upper and surfaces of the cut l:p separated by a gap h and connected by a tube 'Ep whose is the dislocation line I and whose radius is p. The scheme ofthis surface is sketched 22. 0PidoXi
°
5. Interaction of dislocations with an elastic field 5.1. The action of a stress field on a dislocation Let us consider a dislocation loop I in a field of external elastic stresses Pik created by given loads, and find the force on the loop in such a field. We calculate the work bR done by external loads in an infinitesimal displacement of the loop I. If this work is written as (50)
bR = tFbxdl,
where bx is the displacement of the dislocation line element, then Fwould determine the force on unit length of the dislocation line. Let the displacement of the dislocation cause a certain change of the displacement vector bu. Then the work of the external stresses done on the volume 1', which includes the dislocation loop, is given by
bR =
f»«
(51)
bu, dE ;00,
where 'E is the closed surface bounding the volume 1'. It is convenient here to use transformations of the integral of eq. (51) which are based on Gauss's theorem and therefore the displacement u around the dislocation should be considered as a single-valued function of the coordinates. In that case this vector will have a discontinuity on the surface 'Es spanning the dislocation loop. In order to eliminate the points of discontinuities of the vector u, we assume the loop I to be enveloped by a certain closed surface 'E° outside which the function u = u(r) is continuous (in the volume 1"). Then (jJ
s« ~ =
f [O(P'k bu,)/ox,] dr ' - f P;, bu, dE?
,.
J
(oPidoXk) bU i dr
,.
+ JPik s-; dr + JPik bukn? d'E°,
where the normal nO is directed outwards from the surface 'E 0.
* There
is a similar step of b in the line of the first dislocation.
Fig. 22 The dislocation line I is enveloped by a tube It which has radius p and joins the upper and lower surfaces of the cut Is.
If we neglect the local perturbation of the crystal which is caused by the dislocation along its axis and is insignificant in the estimation of the interaction of the dislocation with the elastic field, the remaining volume integral on the right of eq. (52) can be reduced to the integral over the total volume 1'. In fact, as the stresses and strains are continuous functions, the integral over the volume 1" turns into the integral over the total volume 1', when one surface of the cut 'Es approaches the other (h -+ 0) and the radius of the tube decreases (p -+ 0):
fPik s-; fPik dr ' --,
(53)
The surface integral in eq. (52) can be also simplified by a relevant limit transition. In particular it should be noted that the integral over the tubular surface 'Et becomes zero as p -+ 0, because the displacement field of the dislocation has the following feature lim pu(r) = O. p-tO
The values of the continuous quantities P« are the same on both surfaces of the cut, but the limit values of u differ by a given amount h. Therefore, instead of eq. (52) we have
bR = (52)
beik dr.
fP;, be;, dr + i JPlI be
kk
dr
+ b;b JP;k az,
(54)
where P;k is the stress deviator, e;k is the strain deviator (e;k = eik - :tbikel/) and the first two volume integrals replace the integral of eq. (53) according to the evident identity Pikeik
= (Pik - :tbikPll)e ik + :tPllekk = P;ke;k + :tPllekk·
A. M. Koseoich
64
Ch.l
Since the distribution of the stresses Pik is assumed independent of the position of the dislocation, we take the difference symbol £5 outside the last integral in eq. (54). If the element of the dislocation line dlis displaced by an amount £5x, then the area of the surface Ls changes, the elementary change being (55) The relation of eq. (55) should be used in the transformation of the last integral in eq. (54). In the case where the displacement £5x lies in the dislocation glide plane, eq. (55) characterizes the main changes in the crystal. However the situation is different in the presence of a displacement which is perpendicular to the glide plane. In this case, the additional requirements which follow from the continuity of the medium become rather essential. It is usually of interest to study those motions of the dislocation which take place without disturbing the continuity of the medium. Then, as shown in sect. 4.2., the displacement of the dislocation is accompanied by a local relative change of the volume which is given by eq. (42). Using this equation for the transformation of the second integral in eq. (54), we may write (56) Now, with eqs. (55) and (56) in mind, we can separate that part of the work £5R which is associated with inelastic deformation of the medium arising from the displacement of the dislocation. Write eq. (54) in the form
~R =
JPik
~e;k dr + ts;","I",(P"k - 4(j"kPll)b k ~X; dl.
ts;","I",P;kbk
~x; dl
FEy = _b'Plxx --
-~b(2.p 3 xx
- Pyy - Pzz ) .
65
(61)
It is of interest to determine the component of the force of eq. (59) lying in the
plane of the corresponding element of the dislocation. Let K be a vector normal the dislocation line in the glide plane. Then the required force component (f, say) = KF = Cikl KJkPlmbm or (62) where n = K X t is the normal to the glide plane. Since the vectors nand bare perpendicular, we see that the force f is determined by only one component Pik if two of the coordinate axes are taken along these vectors. If the dislocation forms a plane curve which lies entirely in its glide plane and the external elastic field is uniform, then the force f is the same for all the elements of the dislocation line irrespective of their positions on the glide plane. The last fact is used in the quantitative description of a Frank-Read source (see sect. 5.6.). Since the force of eq. (62) may cause motion of the dislocation in its glide plane its magnitude would determine the start of plastic deformation in the crystal. Equation is in agreement with the experimental result that slip begins when the shear stress niPikbk/b reaches a value which is characteristic of the crystal, but independent of the other components of the applied stress. The total force acting on the whole dislocation loop is
(57)
The first integral in eq. (57) is equal to the increase of the elastic field energy in the body. The linear integral over the dislocation loop, namely
~RD =
Crystal dislocations and the theory of elasticity
(63)
This is zero except in the case of a non-uniform field' when PI = constant the integral is f dx, = O. If the stress field varies only slightly ~ver the 'loop, we can 'write:
(58)
yields the work of the displacement of the dislocation. Comparison of eqs. (58) and (50) shows that the force on unit length of the dislocation is
This force can be expressed in terms of the dislocation moment dk1 defined by eq. (16):
(59) A formula of the kind eq. (59), where the stress deviator P;k is replaced by the stress tensor Pik was derived first by Peach and Koehler [6]. Weertman [17J pointed out the necessity of taking into account the inelastic change of volume in dislocation climb, i.e. the necessity of replacing Pu. by Pi« _. j £5 ikPll' As a trivial example of the use of eq. (59), we consider the forces on screw and edge dislocations. Let the z-axis be parallel to the dislocation line (tz = -1). In the case of the screw dislocation b, = b, and
F; =
(64)
If there is a uniform stress field near the dislocation loop and F T = 0 the dislocation
is acted upon by a couple with the moment
(60)
which also can be expressed in terms of the dislocation moment of the dislocation loop:
In the case of the edge dislocation the x-axis is taken along its Burgers vector ib ; = b).
(65)
F; = bpyz'
-bpxz'
A. M. Kosevich
66
Ch.l
We consider a plane circular prismatic dislocation which has the Burgers vector b perpendicular to the loop plane (along the z-axis). Such a dislocation is acted upon by the following moment of forces:
where S is the area of the loop.
Crystal dislocations and the theory of elasticity
§5.2
The force between two edge dislocations is not, generally speaking, radial and, besides, has essential angular dependence even in an isotropic medium. We assume the glide planes of the dislocations to be parallel. Let the z-x-plane be parallel to the glide planes and the z-axis be parallel to the dislocation lines. Then calculations may be made directly by using eqs. (61) and (25). If one dislocation is along the z-axis (fig. 23), it exerts on the other dislocation (passing through the point (r, 8) on the x-y-plane) a force whose component in the glide plane is
5.2. Forces between straight dislocations The Peach-Koehler formula (eq. (59)) allows us to describe the interaction between two dislocations in an obvious way. If Piker) represents the stresses produced by one dislocation near an element dl of the other dislocation having Burgers vector b, then the relationship (66) determines the force exerted by the first dislocation on the element dl of the second dislocation. However, eq. (66) is useful only in the description of the interaction between dislocation lines of simple shapes and orientations. For example, it is easy to analyze the interaction between two dislocation loops, if the distance between them considerably exceeds the dimensions of the loops, For that it is enough to substitute the stress tensor obtained by using eq. (15) in eqs. (64) or (65). But consideration of the force of interaction between two closely situated dislocations would require cumbersome calculations. Often it is more convenient to characterize the interaction between arbitrary dislocation loops by their interaction energy (see sect. 6.4.). Note that only the interaction of straight dislocations can easily be considered in the general case. We shall calculate the forces between two parallel straight dislocations in an isotropic medium. The interaction force between nonparallel dislocations was calculated by Kroupa [18]. We begin our considerations with the simpler case of two screw dislocations. The force per unit length acting on one dislocation in the stress field due to the other dislocation is determined from eq. (60), using eq. (29). It is a radial force of magnitude
= f.1 b I b 2 .
F r
67
b M F; = b 12
cos 8 cos 28
r
'
M
=
f.1/ 2n (1 - v).
(68)
It is this component that presents the greatest interest, since the displacement of the dislocation may occur as a mechanical motion only in the glide plane. The equation of this component ofthe force to zero corresponds to the equilibrium configuration ofthe two dislocations relative to slip. It follows from eq. (68) that F; is zero at 8 = 0 and () = It can be easily verified that the first position (fig. 24a) satisfies the requirement for the stable equilibrium of two dislocations with like signs (b i b2 > 0), while the second one (fig. 24b) does so for the two dislocations with unlike signs (b i b2 < 0). It is evident that the first configuration (fig. 24a) also remains in equilibrium if there are more than two dislocations. This is an explanation of the fact that straight edge dislocations which lie in parallel glide planes have a tendency to gather in one plane perpendicular to their glide planes. The array of parallel edge dislocations placed in the plane perpendicular to their Burgers vectors is called a dislocation wall. The tendency of dislocations to form isolated dislocation walls leads to polygonization. The equilibrium configuration in fig. 24b is the basis of the formation of double dislocation lines, the so-called dipoles. Two parallel straight edge dislocations which lie in the same glide plane (8 = 0) interact with the force
in.
F x
=
b lb 2M r
=
-
b lb 2M
IX I
-
x 21
,
(69)
where Xl and X 2 are the coordinates of the first and second dislocations, respectively. Equation (69) shows that dislocations of like sign (b I b2 > 0) which lie in the same glide plane repel, while those of unlike sign (b I b2 < 0) attract.
(67)
2nr
y
Screw dislocations oflike sign (b i b2 > 0) repel, while those of unlike sign (b i b2 < 0) attract. y
x
o
e o Fig. 23 The component F; of the force on a dislocation at (r, 0) produced by a dislocation at the origin.
(a)
Fig.24
(b)
The stable equilibrium positions of two dislocations. (a) The dislocations have like signs. (b) The dislocations have opposite signs.
A. M. Kosevich
68
Ch.l
A similar expression yields the interaction force between edge dislocations which lie in the same glide plane in an arbitrary anisotropic medium. However, the coefficient M, in this case, is expressed in terms of the elastic moduli of the medium in a more complicated way. Finally, we pay attention to the problem of forces between straight dislocations which form a node of the dislocation network. The theory of a regular dislocation network was given by Frank [19]. It was extended later by a number of workers, and was verified experimentally (see e.g. [20]). The accurate expressions for the forces between three dislocation lines, which converge in one point, were derived by Indenbom and Dubnova [21]. They demonstrated the invalidity of the linear tension approximation (see sect. 3.4.) in this problem. The equilibrium configurations of the dislocations in such a node were also obtained [21].
Crystal dislocations and the theory of elasticity
§5.3
from eqs. (61) and (25) by summing the contributions from all the dislocations in the wall: L X2 - (y - 11)2 d1] 2LbD x(x 2 - y2 + L 2) 2 2 F; = bDx -L [x + (y _ 11)2]2 -; = -w- (x _ y2 + L2)2 + 4X2y2' (70)
f
The force of eq. (70) tends to pull the dislocation into the plane of the wall or to drive it out according to whether (x 2 - y2 + L 2) is positive or negative. In fig. 25 the region of attraction is bounded by the hyperbola. Thus, the dislocation wall which nucleated in the crystal automatically provides the conditions for its further growth. It is of interest to calculate the shear stresses produced by an infinite dislocation wall over large distances. The element Pxy of the stress tensor produced by all dislocations of the wall* is given by a sum
5.3. Pelygonizatlon and a dislocation model of grain boundaries
00
Pxix,y)
It is not difficult to understand that a uniform distribution of edge dislocations with parallel Burgers vectors is unstable relative to the formation of dislocation walls. We consider a dislocation system containing a large number of parallel edge dislocations which can move in their glide planes. It follows from eq. (68) that the force on an isolated dislocation exerted by other uniformly distributed dislocations is zero. Therefore, a nonzero force may occur only owing to the local disturbance ofthe symmetrical configuration of neighbours near the dislocation under consideration. Then, two or three dislocations arrange as in fig. 24a, giving an origin for the formation of the dislocation wall. Suppose that the process of building up the wall has continued until a wall. of length 2L has been formed (fig. 25). The dislocations are assumed, for simplicity, to be at a uniform spacing ofw. We find the force in the glide direction on a dislocation at a point (x, y) at a distance from the wall large compared with w. This force is obtained
\ \
\
\ \ \
\ \
x
'\
01. -, I
\
\
/
\
/ I
T;
-Lw
/
/ /
/
-L
\
\ \
\
69
= Dx
n=~
00
x2 [x 2
_
+
(y _ nw)2 (y - nw)2]2'
(71)
For x » w the sum reduces to Pxy
= 411?D(x/w 2) e-2nxjw cos (2ny/w).
(72)
Thus the stresses decrease exponentially away from the wall. Therefore, unlike the field of an isolated dislocation, the elastic field of the wall is concentrated in a thin layer, the thickness of which is of the order of the spacing between the dislocations. It is easy to understand the geometrical meaning of the crystal deformation produced by such an array of dislocations. The presence of the dislocation wall leads to the misorientation of the two parts of the crystal separated by the plane of the wall (fig. 26). If w is the distance between the dislocations then the misorientation angle of the two parts of the crystal is l/J = b /w. It is necessary in the macroscopic theory that w » band l/J « 1. The dislocation wall may be considered as a model of the boundary between two blocks or subgrains with a slight misorientation. If the boundary consists of edge dislocations, then the axis about which the neighbouring subgrains have been tilted lies in their interface. Such a boundary is known as a tilt boundary in contrast to the twist boundary in which the two grains are rotated about the normal to their interface. The twist boundary contains a certain grid of screw dislocations. The arrangement of the dislocations in the grain boundaries formed in the manner described is called polygonization. The formation of regular boundaries involves both dislocation glide into the neighbourhood of the boundary, often by large distances, and the climb of dislocations normal to the glide plane by short distances. The latter is required to form a reasonably uniform distribution of dislocations in the . boundary**. It was mentioned that elastic stresses decrease exponentially with increasing distance from the dislocation wall. This means that the single crystal remains unstrained on
\
Fig.25 A dislocation wall and its action on a dislocation at a point (x, y). The force in the glide direction tends to attract the dislocation into the plane of the wall above and below the two branches of the hyperbola.
* The detailed analysis of all the elements of the stress tensor due to the dislocation wall is given in works by Li [22]. ** At low temperatures when glide but not climb is possible, only short boundary segments are formed.
Ch. 1
A. M. Kosevich
70
71
Crystal dislocations and the theory of elasticity
§5.4
~Em 1r----~~--~
o Fig.27
Fig. 26 A dislocation model of a tilt boundary: two grains inclined at a small angle lj/.
both sides of the boundary, and its lattice is regular. All the elastic energy associated with the junction of two slightly misoriented parts of a single crystal is concentrated in a narrow layer near the grain boundary. The energy of the subgrain boundary may be easily estimated as a function of the misorientation angle t/J . We use the fact that the elastic field of the wall decreases exponentially at distances x » w and coincides with the field of an isolated dislocation at x 2 + (y - nw)2 « w 2. Then. for a rough estimate we may regard the elastic energy of the wall as the sum of contributions from the isolated dislocation, supposing each single dislocation to be situated along the axis of a cylinder of radius iw. The energy per unit length of this dislocation is equal [see eq. (35)J to
tlb2 W ----log-, 4n(l - v) 2ro
We suppose for definiteness that the z-axis is parallel to the dislocations, the x-z-plane is the glide plane and the Burgers vectors of the dislocations are in the x-direction. Then the force in the glide plane per unit length of a dislocation is bpxy, where Pxy is the stress at the position of the dislocation. We consider a set of n edge dislocations in which the leading dislocation is held up at the point Xl = 0 (fig. 28), and remaining dislocations are in equilibrium at points X 2 . . . X n such that
l.
btl t/Jo E(t/J) = 4n(1 _ v) t/J log T'
(73)
where t/Jo = ib/r o· The energy of the subgrain boundary of eq. (73) as a function of t/J is illustrated in fig. 27. ThefunctionE(t/J)hasacuspatt/J = oand a maximum Em att/J = = t/Jo/e. The quantitative agreement of the relation of eq. (73) with experiments is discussed in refs. [23, 24J.
v;
5.4. Planar dislocation pile-ups Let us consider a large number of similar straight dislocations lying parallel in the same glide plane, and derive an equation to determine their equilibrium distribution.
1
ffi
.Lx 8
Fig. 28
where the radius of the dislocation core ro is independent of t/J provided that t/J is reasonably small. The distance between neighbouring dislocations is w = b/t/J and, hence, the energy per unit area of the grain boundary is
The grain boundary energy E(lj/) as a function ofljJNm'
Dislocation pile-up. The leading dislocation is held up at the point x the origin and crosses the glide line at a point x.
=
O. A circuit T surrounds
The problem is to find the law of the distribution of dislocations along the x-axis under a given external stress. This distribution may be obtained from the condition of equilibrium for each dislocation subjected to an external force and the force of interaction with other dislocations in the set. Taking into account the interaction force of eq. (69) and the force on the dislocation exerted by the external stresses, we can write the condition of equilibrium" as
±
=
D
i= 1,i*k Xi -
Xk
P~/Xk)'
k
= 1,2, ... n,
(74)
where P~y(x) is the external shear stress, and D = tlb/2n(1 - v). The problem of the dislocation distribution is thus reduced to the resolution of the nonlinear system of algebraic equations determining the X k. * See Addendum 5 and 8.
A. M. Koseoich
72
Ch.l
A special method for the solution of this system was suggested by Eshelby, Frank and Nabarro [25]. It appears that if we introduce a polynomial of degree n which has X k as its zeros, this polynomial satisfies a certain differential equation of the second order with variable coefficients. Thus, e.g. if the position of the first dislocation is fixed* and the external stress is uniform, the coordinates of the remaining dislocations in the set will be the zeros ofthe derivative of the n-degree Laguerre polynomial. Using the asymptotic expression at large n for the zeros of the Laguerre polynomial, Stroh [26] later calculated the stresses due to such a dislocation pile-up. We may determine the solution of the problem of the distribution of n dislocations more directly by proceeding from the assumption that the number of the dislocations in the pile-up is rather large and the dislocations are continuously distributed over their glide plane. Let .@(x) be the line density of dislocations on a segment (L 1, L 2) ofthe x-axis: b'@(x) dx is the sum ofthe Burgers vectors of dislocations passing through points in the interval dx. Then the total stress at a point x on the x-axis due to all the dislocations is given by the integral**
__I
L
PXy(x) -
D
2
L1
.@(x') dx'. -,-X - x
(75)
For points in the segment (L 1 , L 2 ) this integral must be taken as the Cauchy principal value in order to exclude the physically meaningless action of a dislocation on itself. The condition of equilibrium of a dislocation at the point x has the form t
p
I
L2
L1
.@(x') dx'
r; (x)
= _x_y_ == (V (x ),
x' - x
D
(76)
where P denotes, as usual, the principal value. This is an integral equation to determine the equilibrium distribution .@(x). It is a singular equation with a Cauchy kernel. Such an approach to the problems of dislocation pile-ups was first suggested by Leibfried [27]. The function .@(x) satisfies the following explicit normalization requirement ~(x)
dx = n.
(77)
L1
The theory of singular integral equations with a Cauchy kernel was discussed in detail by Muskhelishvili [28] and we confine ourselves only to some certain results of this theory [14]. Let us consider the case where there are no external stresses ((V(x) = 0) and the dislocations are constrained by some obstacles (lattice defects) at the ends of the segment (L 1, L 2). For (V(x) = 0 eq. (76) has a nontrivial solution ~(x)
= n/n[(x - L 1)(L2 - X)]1/2,
* This may be, for ** See Addendum
t
example, a so-called sessile dislocation. 5.4. See Addendum 5 and 8.
73
which describes a pile-up of n dislocations. We see that the dislocations pile up towards the obstacles at the ends of the segment with a density inversely proportional to the square root of the distance from the obstacles. The stress outside the segment (L 1 , L 2 ) increases in the same manner as the ends of the segment are approached, e.g. for x > L 2 Pxy ~ nD/[(x - L 1)(L2 - L 1)r /2. In other words, the concentration of dislocations at the boundary leads to a stress concentration beyond the boundary. If the dislocations are constrained only by external stresses, then the function ~(x) is given by the formula:
1 ~(x) = - n2 [(L 2 - x)(x - L 1)]1/2 P
I
L
L1
2
[(L
2
(V(x') - x')(x' - L
1)]1/2
dx' x' - x
(78)
The solution of eq. (78) has the following feature: '@(L1) = ~(L2) = O. Equation (76) may have a solution of this kind only under the condition [28] (V(x) dx = 0 x)(x - L 1) ] 1/2 .
(79)
Finally, we describe the dislocation distribution on a segment with an obstacle at one fixed end of the segment (say, at a point L 1 ) . For simplicity, we take L 1 = 0 and L 2 = L. Then the solution will be ~(x)
X)1/2 = - -12 (L --P rr
x
If the stress field is uniform eq. (80) gives
P0 ~(x) = _
L2
I
Crystal dislocations and the theory of elasticity
§5.4
rrD
f.L ( 0
(p~ix)
(L X)1/2 . _-_ x
x'
L - x'
)1/2 (V(x') dx' . x' - x
(80)
= -Po), then the calculation of the integral of
(81)
This function is sketched in fig. 29. The condition of eq. (77) determines the length of the dislocation pile-up L = 2nD/po. Beyond the obstacle there is a concentration of stresses near it given by Pxy ~ - Po(L/lxj)1/2.
(82)
Relations of the type of eqs. (81) and (82) were used by Stroh [26] to calculate the stress concentration in the neighbourhood of the head of the dislocation pile-up. In conclusion we determine the difference in displacements in the glide direction on the opposite sides of the plane surface along which the continuously distributed dislocations are situated. Consider a circuit T surrounding the origin of coordinates and crossing the glide plane at a point x (fig. 28). Take u(x) = »; u; where u:
* See Addendum 5.4, 2.
74
A. M. Kosevich
Ch. I
D9;J(x)
TIpo
o Fig.29
The dislocation density
~(x)
as a function of xfI: The concentration of the dislocations at the head of the pile-up is shown.
and u; are the crystal displacements at a point x above the glide plane and under it, respectively. Then, with the definition of a dislocation eq. (1) we have u(x)
=
lJr ~u~ dx] =
-B,
Crystal dislocations and the theory of elasticity
§5.5
75
the resistance of the crystal to the displacement of the dislocation. The magnitude of the frictional force depends on the type of the dislocation and to a considerable degree, on the model of the dislocation core. To study the role ofthe discrete structure of the crystal lattice, Peierls [29J suggested a simple model which now has his name. The Peierls model for the edge dislocation is, in essence, the following. Let the atoms of the undistorted crystal form a simple tetragonal lattice with a period b along the x-axis and with a period a along the y-axis (fig. 30). We consider two parts of such a crystal, one of which (A) has an extra atomic plane as compared with the second part (B). Put these two parts together and form a single crystal by bringing together upper and lower parts at the lattice parameter a and by matching left and right edges of the two parts. To achieve the latter we may fix the right edges of the parts A and B and then cause a relative shift of their left edges along the x-axis by the distance b. When the two parts of the crystal combine, the atoms form a single lattice which has an edge dislocation (fig. 30b).
(83)
UX k
where B is the total Burgers vector of the dislocations embraced by the circuit T': B = b
I:
A
!'0(x') dx '.
(84)
\
L
It follows from eqs. (83) and (84) that u(x) =
-i
I:
=
!'0(x') dx.
I du(x) ----. b dx
-x 8
(a)
Thus, the dislocation density is determined by the derivative of the relative displacement of the crystal on the opposite sides of the slip plane: ~(x)
r-
(b)
Fig. 30 The formation of a single crystal from two separated parts A and B. (a) The part A has an extra atomic plane as compared with the part B. (b) The two parts A and B are joined and make a united single crystal with an edge dislocation.
(85)
5.5. The Peierls-Nabarro force In preceding sections we discussed the force on any dislocation in a continuous medium. This force arises from the elastic stress field. However, a dislocation in a crystal is also acted upon by forces which cannot be described by elasticity theory. We call these forces, which are "extraneous" to elasticity theory, forces of inelastic origin, and discuss briefly only two types of such forces. Inelastic forces of the first type act on partial dislocations. A single partial dislocation is a contour of some planar stacking fault in the crystal, and it is acted upon by the surface tension connected with the surface energy of the defect. This force is always directed in the plane of the defect normal to the dislocation line at a given point. The contribution of the surface tension is very important in writing the equation ofequilibrium of a thin twin in the crystal (see sect. 5.7). Inelastic forces of the second type are due to the discrete nature of the crystal and the atomic character of the structure of the dislocation core. These forces describe
We denote the relative atomic displacement of the two sides of the glide plane in the direction of the x-axis by u(x). The crystal lattice should be perfect at infinitely large distances from the dislocation, and this is possible if the condition
u(oo) = 0,
u( - (0)
= b
(86)
ib
is satisfied. We take u(X) = and suppose the center of the dislocation to be in a point x = X. To determine accurately the function u(x) we assume that the upper and lower parts of the crystal may be considered as two elastic continuous half spaces; however, the tangential stress in the interface is supposed to be a periodic function of the local relative displacement u(x) with period b. Peierls took the simplest periodic function, namely, a sinusoidal function: P
=
III sin (2nu(x)/b) ,
(87)
where the coefficient /11 has the order of magnitude of the elastic modulus of a crystal. We shall show below the way in which it is determined.
Ch.l
A. M. Kosevich
76
The local stresses of eq. (87) must coincide with the macroscopic stresses caused by the nonuniform distribution of the displacement u(x) along the whole glide plane. We have already seen that a nonuniform relative displacement u(x) on the opposite sides of any plane is equivalent.to a certain distribution of edge dislocations along this plane with the density of eq. (85). Therefore, it causes the shear stresses of eq. (75). Substituting eq. (85) in eq. (75) and comparing the result with eq. (87) for plJj(x), we obtain a singular integral equation for u(x): P
foo _ 00
du(x') dx' dx x - x'
= _ fll b sin (2TC U(X)). D
b
D
x
foo dU(~') dx' -00
dx
= ~.
Let us now calculate the derivative with eq. (90). Then we find
oUx/oy at y =
°by using eq.
(90) (22) and compare it
_ 00
du(x') ~ = _ 2(1 - vl~ sin [2TC U(X)]. dx' x - x' 3 - 2v a .b
(91)
The solution corresponding to the conditions of eq. (86) is u(x) =
~b
(1 _
2 tan-l x -: X),
tt
(92)
J,
where
3 - 2v
), = 4(1 _ v) a.
Jo
sin (2TCU/b) du (94)
Now, take into account the discrete structure of the glide plane and denote the coordinates of atomic rows by X n starting the numbering of the layers in the vicinity of the dislocation centre: X n = nb, where n = 0, ± 1, ± 2,. .. The total energy of misfit of the crystal with one single dislocation is
E=
(95) n = -
00
n = -
00
It follows from eq. (92) that
~ ) ~ (x
_
~2
+ A2·
(96)
Substituting eq. (96) in eq. (95) and carrying out the summation over n by an aid of Poisson's summation formula, we obtain for the energy per unit length of the dislocation in the first approximation (A » b):
= Db + 2Db e- 2 n A/ b cos (2nX/b).
(97)
It is seen that the dislocation energy is indeed a periodic function of the dislocation position. By using eq. (97) we may 0 btain the force on the dislocation produced by the crystal structure
Thus, the Peierls equation takes the form
foo
rU~)
p<;j(x) du = -bfll
= fll b2/TC sin" (nu(x)/b).
E
III = Il b/ na(3 - 2v).
p
Jo
sin' (nu(x)/b) = cos" (tan -1 x
Thus, at large distances from the dislocation core, the relative displacement is u(x)/b = D/2fll nax.
rU~)
Vex) = -b
(89)
x
77
It is easy to estimate the critical shear stress which is required in the Peierls model to start the movement ofthe dislocation in the glide plane. This was estimated by Nabarro [30] by using the following consideration. The stress p<;}(x) produces the potential energy of any atom row
(88)
The solution of eq. (88) should satisfy the boundary condition of eq. (86). Now we find the relation of the coefficient fll to the elastic modulus of the crystal. It is clear that far from the dislocation core (x » b), where the displacements u(x) are small, the solution of eq. (88) should coincide with the solution given by elasticity theory Ceq. (22)J if one takes y = 0 and oUx/oy = u(x)/a. It follows from eq. (88) that for x ---+XJ, when u « b, we have 2nfll u(x) = _ 1
Crystal dislocations and the theory of elasticity
§5.5
oE = -Zub '. - e- 2 n A/ sm (2nX/b). oX 1 - v
F = - -
b
(98)
The formula of eq. (98) determines the so-called Peierls-Nabarro force. The maximum value of this force Fm determines that shear stress as = Fm/b which should be applied to the crystal in order to initiate the movement of the dislocation in its glide plane. To estimate o"s, we take A = a and a = ~b. It appears then that as '" 10- 4 fl. If a = b, then as'" 10 - 2 fl. These are the values that were given above in the discussion of dislocation glide.
(93)
The value A may be conditionally called the half-width of the dislocation. The conditionality of this concept is connected with a slow spatial change of the displacement u(x), and that makes the estimation of the dislocation width rather strongly dependent on the particular form of the periodic function p<;}(x). The dislocation half-width as a function of the magnitude of Poisson's ratio may take values in the range from A = ~a (for v = 0) to A = a (for v = ~).
5.6. Dislocation sources To ensure a considerable plastic deformation, there should exist some mechanisms of dislocation multiplication in the crystal, i.e. some dislocation sources should function. One of the simplest schemes of a continuously operating source of dislocations was suggested by Frank and Read [31]. We consider a straight dislocation segment fixed at two points A and B. This may
cu.i
A. M. Kosevich
78
(b)
Fig. 31 A dislocation segment fixed at two points A and B. (a) A and B are nodes of the dislocation network. (b) A and B are bends on the same dislocation.
be a segment between two nodes of the dislocation network (fig. 3la) or between two bends in the same dislocation (fig. 31b). We assume that a uniform applied-stress has only that component which creates a force in the glide plane of the element AB and does not create forces in the glide planes of other adjacent dislocation segments. Then, in the glide plane of the element AB there is a force/which is given by eq. (62) and is directed normal to any element of the dislocation AB. If this force exceeds the retarding force in the crystal, the dislocation line AB begins to move, remaining fixed at the points A and B. As a result it will bend in the form of a certain loop which connects the points A and B. The shape of this loop can be found by using a simplified mathematical description, the so-called line tension approximation (see sect. 3.4.). If the line tension To is independent of the shape of the loop and of the orientation of the element of the dislocation line, the equilibrium form of the loop is a circular arc of a radius R (fig. 32) given by the condition
I
To
>
If + F res '
(99)
where F res is the static force of the crystal resistance acting on the dislocation. The line tension is approximately To ~ ub", It is clear that there is a certain critical equilibrium radius of the arc R o , where 2R o is the distance between the points A and B. For small values of/when
/ <
To
/0 = IF + r.; o
Fig. 32 A stable circular arc of dislocation AB has a radius R > R o' where R o is the critical dislocation radius.
Crystal dislocations and the theory ofelasticity
§5.6
79
exists always an equilibrium dislocation loop of radius R > R o . If/ > /0' the loop has no equilibrium form. In this case, the dislocation will move, expanding freely in the glide plane. The successive positions of such a loop in the glide plane are shown in fig. 33. The original line 1 bulges to a loop 2, then to 3. At 4 two elements of the loop are about to meet. They annihilate, and the next configuration is a closed loop 5 together with a short segment of the dislocation joining A and B. The loop 5 now expands freely as a single dislocation line. The short segment again begins to pass through the successive configurations 2, 3, 4, ... The dislocation segment AB, which can give rise to a succession of closed loops of dislocations, is called a Frank-Read source.
Fig. 33 The Frank-Read source. A segment AB of the dislocation line is held fixed atA and B. Under an applied stress the segment AB moves from 1 to 2, then to 3, 4 and finally to 5.
Let us write / = ba, wherec is an external shear stress. Then the critical shear strength (J 0 which is required to operate a Frank-Read source of length 2R o is given by (J
o
F res = /0 - = -To - +-.
b
bRo
b
(100)
The relationship of eq. (100) is obtained by using the line tension approximation. However, Indenbom and Dubnova [2lJ have shown that this approximation does not provide a correct description of the dislocation configuration near the nodes in the network or bends at the points A and B in fig. 31. The exact calculation [32J yields a value of the critical shear stress which exceeds that obtained in the line tension approximation. If (J > (J 0 and F res = constant, then the dislocation source may produce, in principle, an unlimited succession of closed dislocation loops. However, often the quantity F res grows with the increase of the radius of the loop expanding in the glide plane. If the retarding force F res increases proportionally to the radius of the loop, then the dislocation source may produce a limited number of dislocation loops. This case was studied by Van Bueren [33]. Orlov [34J discussed the operation of the Frank-Read source in another case when the resistive force grows with the increase of the radius of the loop but this growth saturates. The Frank-Read source can be formed by the way of so-called double cross slip. The deviation of a screw dislocation from the glide plane is known as cross slip (see
80
A. M. Kosevich
Ch.1
sect. 4.1.). Consider a dislocation in which a screw segment (AB in fig. 34) cross slips, forming a loop AA'B'B in the cross slip plane. The segment A'B', which is a pure screw one, can move by double cross slip into a new glide plane parallel to the original slip plane. If the points A' and B' are fixed, the segment A'B' acts as a Frank-Read source.
Crystal dislocations and the theory ofelasticity
81
5.7. The dislocation model of the twin The simplest example of a twin in the crystal is schematically shown in fig. 36. The atomic layers on the opposite sides of the so-called twin plane ZO X are turned relative to each other by an angle 20:. The twinned and un twinned parts of the crystal are mirror reflections of each other in the plane mentioned. The interface boundary between the upper and lower parts of the crystal in fig. 36 is a perfect lattice plane; in that case one speaks of a coherent twin boundary. y
Fig. 34 Double cross slip. A screw segment of dislocation AB moves out of the primary slip plane into the cross slip plane. A screw segment A'B' of the loop in the cross slip plane moves into a new glide plane parallel to the primary slip plane.
If the dislocation lying in its glide plane is fixed only at one but not two points, it can also serve as a dislocation source. It is said in this case that a pole mechanism of the generation of dislocations operates. When all parts of the dislocation line move across the glide plane with about the same linear velocity, the dislocation line winds itself into a spiral in the glide plane. The successive positions of a dislocation fixed at a point A are shown in fig. 35. Such a source does not emit a succession of dislocation loops but a dislocation spiral. The corresponding pole mechanism is often called a mill.
Fig. 36 A coherent twin boundary. The angle of twinning is 2a.
If the twin has finite transverse dimensions then the outline of its cross section in the x-y-plane is a curve (fig. 37) and therefore it cannot coincide with a crystal plane. Vladimirskiy [36J has shown that, in the general case, the twin boundary consists of single coherent areas separated by twinning dislocations (fig. 38). The Burgers vector of such a dislocation lies in the twinning plane, which is simultaneously the glide plane of the twinning dislocation. The twinning translation is always smaller than the slip translation.
------5 ~-----4 ~-----3
_------2
Fig. 35 The pole mechanism of the generation of dislocations. A dislocation is fixed at point A. Under stress it takes successively the configurations I, 2, ... ,5, forming a spiral source with A as a centre.
A mechanism which has much in common with the Frank-Read source described above may also operate when the dislocation moves by climb instead of glide. This type of source is usually called a Bardeen-Herring source [35J.
Fig. 37 The cross-section of a twin at the surface of a crystal.
Fig. 38 A twinning dislocation after Vladimirskiy [36J.
The twinning dislocations are located along the contour of the twin (fig. 39). The density of such dislocations is determined by the curvature of the boundary of the twin.
82
A. M. Koseuich
Ch.1
Before discussing the dislocation description of the twin it is useful to consider a twinning dislocation from another point of view. Let us imagine the twin band shown in fig. 40. The monatomic edge of this band is a partial Shockley dislocation with its Burgers vector b = 2a tg (J.. where a is the distance between the crystal planes in the direction perpendicular to the twinning plane, and 2(J.. is the angle of twinning.
83
Crystal dislocations and the theory of elasticity
§5.7
Let us consider an elastic twin of infinite length and uniform in the z-direction and in a plane stress field Pik(X, y); this is a two-dimensional problem of elasticity theory. Athin twin in this problem is equivalent to an array of straight twinning dislocations lying along the z-axis and distributed along the x-axis. Further, we assume that the dislocations are distributed continuously along the x-axis. The dislocation theory of twins based on this model is given in detail in the survey by Kosevich and Boiko [37J. Here we only write and discuss some basic equations of this theory*.
~"X
~L (a)
~(x)
x
1 1.. 11.
-L
D
L
( b)
Fig. 42 A twin within the crystal. (a) A cross section of the twin lamella. (b) A schematical diagram of the twinning dislocation density f0(x). The total strength of all dislocations is zero. Fig. 39 A section of the twin boundary with twinning dislocations.
Fig. 40 A monatomic twin lamella ends on a partial Shockley dislocation (shaded circle).
The macroscopic twin is a set of the monatomic planar stacking faults described above which terminate in its boundary. Therefore the twin sketched in fig. 37 may be replaced by the array of twinning dislocations shown diagramatically in fig. 41. In this section we shall analyze only the so-called elastic twin*, the end of which is not fixed. The thickness of the elastic twin h is generally very small as compared with its length L, i.e. h « L, and according to Vladimirskiy [36J we may consider all dislocations to be situated in the same glide plane or twinning plane. Thus the twin may be considered as a certain pile-up of twinning dislocations. Therefore the problem ofthe equilibrium of a twin in an elastic field is the problem ofthe equilibrium of a corresponding dislocation pile-up.
For simplicity, we consider the twin to be not near the surface but within the crystal (fig. 42a). Let us assume that at the origin (x = 0) there is a source of twinning dislocations which can generate under the applied load any number of pairs of straight dislocations with opposite signs. We introduce the density of twinning dislocations £0(x) which is evidently related with the thickness ofthe twin hex) at the point x by "L
hex)
= a
jx
£0(x') dx'.
(101)
We suppose that the stresses are symmetrical about the centre of the cross section of the twin. Then the outline of the twin will also be symmetrical and hex) = h( -x), but £0(-x) = -£0(x) (see fig. 42b). The equation of equilibrium of the dislocations along the twin can be written similarly to eq. (75) as '' L
j
-L
£0(x') dx' _ , - w(x). X
-
(102)
X
However the external forces on the dislocations which are described by the function w(x) must be discussed specially. ----L
Fig. 41 A dislocation model of the macroscopic twin at the surface. The length of the twin is L and the thickness is h.
* If a twin lamella appears when the load is applied and vanishes when the load is removed, elastic twinning is said to take place. If the twin lamella remains after stress relief it is called a residual twin.
We should bear in mind that the slowly moving dislocation is acted upon by forces of inelastic origin (see sect. 5.5.). Firstly, there is a force analogous to some degree to the "dry friction" force, of the type of the Peierls-Nabarro force. Secondly, there is the force of the surface tension on the twin boundary. It is evident that the latter force acts only on the dislocations located at the end of the twin. In fact, the addition of one dislocation at any part of the twin where its width has macroscopic dimensions in practice hardly changes the area of the interface surface between the twin and the matrix and does not essentially change the surface energy. At the same time, the * See Addendum 5 and 8.3.
84
A. M. Kosevich
Ch.l
addition of one dislocation near the end of the twin, where the interface boundaries are separated by a few atomic parameters may essentially change the corresponding surface energy. This statement is confirmed by numerical calculations [38]. The difference in the character of the crystal distortions caused by the dislocations at the end of the twin (by the head dislocations of the pile-up) and by the dislocations on the interface surface can be seen by comparing the diagram in fig. 40 which shows the leading Shockley partial and the diagram in fig. 38 which shows the Vladimirskiy twinning dislocation. Write the function w(x) in the form
Crystal dislocations and the theory of elasticity
§5.7
We have replaced the integrals from - L to L by the integrals from 0 to L, using the symmetry of the problem. Since ST(X) is non-zero only in the region L - x rv d « L wecan put Lf - x 2 :::::; 2L(L - x) in the second integral on therightofeq. (107) and substitute eq. (105). The condition of eq. (107) then takes the form
2
r
a(x) dx
L
~Jo (L 2
= a(x) + S(x\ D
(103)
D
where a(x) = p~/x) and D = fJh/2n(1 - v) in the isotropic approximation. The function Sex) describes the forces of inelastic origin. If the external stresses a(x) grow and the twin increases its size, we have Sex)
= - So - ST(x) ,
(104)
where the minus sign determines the direction of the forces of inelastic origin in the present case. Here So is the dry friction force and ST(X) is the surface tension force. The sign of the force ST(X) is always the same, whereas the sign of the dry friction force varies depending on the direction of the dislocation movement. The possibility ofchanging the sign ofthe dry friction force is the reason for the hysteresis in twinning. The force ST(X) depends on the distance hex) between the twin boundaries and is non-zero only at small hex), i.e. in the narrow region d near the end of the twin. It is natural to suppose that the shape of the twin near its end is determined by the nature of the surface tension and does not depend on the applied external loads. Then in finding the shape of the main part of the twin, the quantity ST(X) becomes a given function independent of o (x):
S (x) = T
{geL - x), geL + x),
x > 0; x < o.
(105)
The definition of eq. (105) is valid only over the region d outside which this function is unimportant. Since the ends of the twin are assumed not fixed, the stresses on them must remain finite. This means that in solving the integral equation (102) we deal with the case for which the solution is obtained by using eq. (78). For our choice of the origin at the midpoint of the segment ( - L, L) this formula becomes .@(x)= -
~ (L 2
X 2 ) 1/ 2
-
n?
pJ"L -L
(L 2
w(x') -
X'2)1 /2
~. x' -
(106)
X
X 2)1/2
-
rg
= So + L 1 / 2 '
(108)
where rg denotes the following constant
_ 2 w(x)
85
rg -
1/2
fOO g(~) d(
tt
0
~ 1/2
(109)
A constant like rg arises also in the dislocation theory of cracks (see, for example, [I4J and the original papers by Barenblatt [39J). This constant can be expressed in terms of the ordinary macroscopic properties of the crystal, i.e. its elastic modulus, and the surface tension on the twin boundary [37J. If one is interested in the properties of the twin at points far away from its ends, then the function g(~) can be replaced by the following delta-function: (110) Relationships of the types given by eqs. (106) and (108) allow us to present a total description of elastic twins in the crystal.
6. Systems ofstationary dislocations in a crystal 6.1. Continuous distributions of dislocations Returning to the initial definition of the dislocation of eq. (1), we rewrite it in the form
ls~
dxiu ik
=
-b k ,
U' k I
=
OUk.
ox,
(111)
The tensor U ik in eq. (111) is often called the simple shear. We shall call U i k the elastic distortion tensor. Its symmetrical part yields the ordinary elastic strain tensor (112) In addition to the condition of eq. (1), which determines the type of the dislocation singularity, it is assumed [1, 40J that in the presence of a dislocation in the medium the elastic distortion tensor U ik is a one-valuedfunction of the coordinates, continuous and differentiable over all of space", In dislocation theory, the distortion tensor is usually regarded as an independent quantity describing the deformation ofthe crystal.
The requirement of eq. (79) must be satisfied, and it gives in this case
L
fo (L
a(x) dx 2 -
X 2)1 /2
1
= 2 nS O +
fL 0
ST(X) dx
(L 2
_
X 2)1/2
(107)
* If we confine ourselves to the requirement that the strain tensor eik and not the distortion tensor U ik be unambiguous, continuous, and differentiable, then we can take into consideration also dislocations of more general type than those defined by the property of eq. (1) (see, for example, [1]).
86
A. M. Koseoich
Ch.l
We write the condition of eq. (111) in a differential form. To do so, we transform the integral round the contour s into one over a surface I spanning this contour:
,h t
=
dxiu ik
f
dIil\/m
oU mk ox/ .
The vector b can be written as an integral over the same surface by means of the twodimensional delta-function b,
~
f
fA b(~) az,
ox,
= - t.b,
s: ) u(~ .
(114)
This is the required differential form. It is clear that on the dislocation line itself (~ ~ 0) which is a line of singularities, the representation of the distortion tensor as the derivatives U ik = OUk/OX i is no longer meaningful. If a crystal contains a large number of dislocations which are at relatively short distances apart (although far apart compared with the lattice period, of course), it is useful to treat them by means of an averaging process. We apply this consideration in those problems in which we are not interested in the exact distribution of the field between the different dislocations and in which the theory operates with physical quantities that are averaged over small elements of volume. It is clear that rather many dislocation lines must cross such "a physically infinitesimally small" volume. An equation which expresses a fundamental property of dislocation deformations can be formulated by a natural generalisation of eq. (114). We define the dislocation density tensor CX ik in such a way that its integral over a surface spanning any contour s is equal to the sum of the Burgers vectors of all dislocation lines embraced by the contour:
f~;k
dE,
The tensor
CX ik
= b.,
87
the index f3 runs over the possible directions of the vector b, and pp(t, r) is the density of the distribution of the vectors band t over the possible directions, r) dO being the number of dislocations having a Burgers vector direction f3 V"~''-'U''b through a unit area perpendicular to the vector t, and located inside a solid angle dO around the direction of t. The integration is carried out over the complete solid angle. seen from eq. (116) the tensor CX ik should satisfy the condition (118)
(113)
where ~ is the two-dimensional radius vector taken from the axis of the dislocation in the plane perpendicular to the vector t at the given point. Since the contour s is arbitrary, the integrals can be equal only if the integrands are equal: oUmk Gilm -;:)-
Crystal dislocations and the theory of elasticity
in the case of a single dislocation states simply that the Burgers vector is along the dislocation line. When the dislocations are treated in this way the tensor U ik becomes a primary quantity describing the deformation and determining the strain tensor through (112). A displacement vector u, related to U ik by the expression U ik = OUk/OXi cannot exist. Really, this is clear from the fact that with such a definition the left-hand side of eq. (116) should be identically zero throughout the crystal. Equation (116) together with ""V11"~''''U~
0PidoXi
= 0
(119)
and with Hooke's law form a set of equations of equilibrium for the continuous distribution of dislocations in the medium [1, 7, 40]. The tensor of the Burgers vector density IX ik in eq. (116) should be considered as a certain continuous function of the coordinates, satisfying the condition of eq. (118). Sometimes, instead of eq. (116) which defines the elastic distortion tensor, one uses an equation for the derivatives of the elastic strain tensor eik . This equation may be obtained by applying the operator Gjpk % x p to both parts of eq. (116) and symmetrizing the result over the indices i and j. Then we have
02
e mk Gilm Gjpk ox/ oX
(120) p
where
(115)
(121)
now replaces the expression on the right of eq. (114) (116)
and describes the continuous distribution of dislocations in the crystal. If we now take into account the fact that the vector b can have only a fixed number of fully defined directions in the crystal then the average dislocation density CX ik can in this case be written in the form [41, 42J
~,.(r) = ~
f
fibfpP(t, r) dO,
(117)
The tensor Yfik is the so-called Kroner's incompatibility tensor [7]. The appellation of the tensor comes from the fact that if Yfik = 0, then eq. (120) coincides with de SaintVenant's compatibility equation for the components of the strain tensor. It follows from eq. (121) that 0YfidoX i
= O.
(122)
This is the continuity equation which states that the incompatibility is solenoidal. Equations (120), (119) and Hooke's law also make a set of equations of equilibrium of the medium with continuously distributed dislocations. There are many ways of solving this system [1, 7, 41]. However, the introduction of the tensor Yfik seems
Ch.l
A. M. Koseoich
88
inconvenient in the analysis of moving dislocations. Therefore we shall refer in further discussion mainly to eq. (116) and characterize the dislocation distribution by the tensor (Xik •
Crystal dislocations and the theory ojelasticity
&"'n .... ,n.c~Tl
The simplest but frequently occurring case of a dislocation distribution is that when the total Burgers vector of all dislocations (denoted by B) is zero. The presence of a dislocation involves a certain bending of the crystal as sketched in fig. 43a (greatly exaggerated). It is clear that in order to produce the macroscopic bend of the crystal, the latter should contain a macroscopic number of dislocations of the same type. It is readily seen that if there are a large number of uniformly distributed parallel edge dislocations of the same sign in the crystal, then this crystal is bent with the curvature I/R = BjS, where B is the total Burgers vector of the dislocations, R is the radius of curvature and S is the cross-sectional area of the bent crystal (see fig. 43b).
the deformed crystal. The total dislocation moment Dik of the crystal is, by of eq. (16),
o.; = ~ s.s,
6.2. Dislocation polarization of the deformed crystal
89
'" 1811mL
'" ±4: silmbk fX
I
dx;
f, mb, dl ~ ! ISilm t
(125)
x, IX"" dr,
the summation is over all dislocation loops and the integration is over the "1"11"" of the crystal. Substituting eq, (124) in eq. (125) we obtain
'"
f »; '" I 1),. =
!
SilmSm,qXI
~~:k dr '" !
f
xm(O£;, -
~~:) dr
after integration by parts in each term,
Pi' dr.
(126)
It follows from eq. (126) that the tensor P i k is actually equal to the dislocation moment of unit volume of the body. Apparently this tensor was introduced for the time by Kroupa [43]. We shall call P i k the dislocation polarization tensor. substitute eq, (124) in eq. (116) and rewrite the latter in the form
(a)
(127) (b) Fig. 43 A plastically bent crystal. (a) Crystal bending caused by one edge dislocation. (b) The crystal is bent with curvature 1/R. It contains a macroscopic density of parallel edge dislocations.
And so the equality B = 0 means that there is no macroscopic bending of the crystal as a whole. The condition B = 0 is, for example, a property of a system of closed dislocation loops. This condition signifies that integration over any cross section of the body gives
I
rJ. ik
dl: i = O.
(123)
From this it follows that the dislocation density may be represented as (Xik
=
ee.;
Cilm
-8-'
(128) It follows from eq. (127) that the tensor of the derivative of some vector Wi k
"""
8uk/8x i ·
W ik
may be always represented in the form (129)
We shall measure the crystal deformation from the state when P i k = 0, assuming that the entire deformation process occurs with B = 0. Then the vector u can be set to the vector of the total geometric displacement u T in the crystal with dislocations, and the tenser W i k determines the total distortion tensor of the deformed body. The equation for the vector u T is derived by using Hooke's law and by substituting eqs. (128) and (129) in eq, (119). If external body forces are absent, this equation reduces to
(124)
Xl
where P i k is a tensor which is naturally zero outside the body. Then the integral of eq. (123) transforms into the integral along a contour outside the body, and becomes zero. It should also be noted that eq. (124) necessarily satisfies the condition of eq. (118). It is easy to see that the tensor P i k thus defined represents the dislocation moment
Thus, when the dislocation distribution is known and the dislocation polarization tensor P ik of the body is specified, the vector u T can be determined from the static equations of elasticity theory, in which the body forces have the density (130)
A. M. Koseoich
90
Ch.1
Crystal dislocations and the theory of elasticity
It should be noted that the force of eq. (130) is in natural accordance with eq. (9) for the force J;(S) which was used for finding the geometric displacement vector around a single dislocation loop. In order to see this we consider a large number of dislocation loops and average eq. (9) over unit volume. The integral Je~~) dr where e~~) is defined by the formula of eq. (5) or the equivalent expression of eq. (43), is equal to
solution of this equation which vanishes at infinity is
Je~1) dr
=
i
J(n.b, + nkb,J az.;
(131)
The right-hand side of the relationship of eq. (131) may be simplified using the notation of eq. (16)
Je~1) dr
= i(dik
Let us consider the equations of equilibrium for an isotropic medium in the case when body forces are absent and the stresses satisfy eq. (119). Equation (119) is satisfied identically if we write (132)
where Xik is a symmetric tensor called the stress function. Kroner [7J introduced a different stress function X;k which depends on the elastic constants of the isotropic medium and is defined by the relation
(133)
(134)
The relation between strain and stress in the isotropic body is given by
eik =
2~(P" -
1 : v Pll Oik}
L1 ==
o2joxt·
+ C,klm dlJ,
R =
Jr - r'l.
(138)
Finally we can find the stress, which is given by
i 1 (02 +~ oX a~k i
- 6ik L1X;[
)J
.
Kunin [44J has obtained by a different method the stresses in an anisotropic medium of any symmetry when 1Jik is given.
Let us consider a system of single dislocation loops in an infinite isotropic elastic medium. The energy of the elastic field of the strains eik and stresses Pik of this system is determined by the standard formula V =
±JeikP" dr.
(139)
We use the representation of the tensor Pik in terms of the stress function Xik and substitute eq. (132) into eq. (139) V --
-21
JeikC,ilmC,kpq-a;:) 02 Xmq dr. ».
(140)
Integrate by parts in eq. (140) and omit the surface integrals at infinity. Then the integral of eq. (140) may be transformed into the form V =
±J~ikXik dr= f1 J(~ikX:k + 1 ~ ~iiX;') dr. V
(141)
In writing down the second part of the equality of eq. (141) we used eq. (133). Now, we substitute eq. (138) into eq. (141) and obtain (135)
It follows from eqs. (120) and (132)-(135) that the tensor X;k satisfies the equation 'L1L1X;k = IJik'
J
, . 1 a R( C,ilm dlk Xik(r) = 16n b, 8X m
uX p
We can show that it is permissible to introduce the three subsidiary conditions
0X;kjOX i = O.
(137)
Interaction between dislocation loops
6.3. Kroner's stress function for an isotropic medium
~ 2f1( X:k + I ~ v X:, Oik}
- r'l1Jik(r') dr,
The stress function of eq. (137) for an isolated dislocation loop reduces to the form
Pu. = 2p [ L1X;k
+ d,,),
where dik is the dislocation moment of a single loop. The subsequent summation over the dislocation loops in unit volume makes evident the correspondence between j(S) and eq. (130).
Xik
-~ fir 8n
X;k(r) =
91
(136)
This is Kroner's basis relation between his stress function and the incompatibility tensor, subject to the subsidiary conditions of eq. (134). The conditions of eq. (134) are satisfied because IJik satisfies eq. (122).
V = - :"
JJ~ik)lf
-
f'I~,,(f') dr dr
8"(;~ v) JJ~i,(r)lf - f'l~kk(f') dr dr.
(142)
Substituting eq. (121) and using a partial integration we can express the energy V terms of the dislocation density O'.ik' We shall not give this relation here, but note
A. M. Kosevich
92
Ch.l
that it is now possible to write the elastic energy of the system of single dislocations in terms of line integrals along the dislocation loops: V --
P "LaPbab ik i k »
1
Crystal dislocations and the theory ofelasticity
dlS:1oc;atllon is made up of a continuous distribution of infinitesimal dislocations. Let distribution be represented by the density
(143)
2" i...J
a,p
(146)
where a and f3 are the dislocation loop numbers and summation is over all dislocation loops. The quantities Lft are given by
(144)
where ~ is a two-dimensional vector measured from the dislocation axis in a plane perpendicular to t, and y(~) is some function that differs from zero in a small vicinity of the dislocation line. If we use eq. (146) in the calculation of the coefficient of the dislocation selfinductance L i k then the expression for L ik becomes
L'k
where
R = IY a
-
Ypl,
n = (Y a
-
_
1
~ 41C(t_ v) f f y(~)y(n d2~ d2~'
Yp)/R.
Other possible expressions for the quantities Lft are given in the survey by de Wit [45J, where the coefficients Lft for loops of simple geometrical shapes are written. These results represented by eqs. (143) and (144) were first obtained by Kroner [7]. It is cenventent to divide the sum of eq. (143) into two sums
-
93
"'LaPbabP ik i k»
2" L,;"
a*p
(145)
The first term, Vin t in eq. (145) is the interaction energy of the dislocation loops. Formally, it looks like the expression for the energy of magnetic interaction in a system of linear, currents. The coefficients L~t are called by Kroner the coefficients of the "dislocationk'mutual inductance" [7]. The-second term in eq. (145), namely Vself , is the sum of the dislocation selfenergies;. Therefore it is natural to call the coefficients Lf: the coefficients of the "dislocation self-inductance". The detailed discussion of the self-energy is given in the next section.
6.5. Tile self-energy of a dislocation loop Let us consider an isolated dislocation loop of arbitrary form in an isotropic medium. Its self-energy is.determined by the coefficient of self-inductance Lf:, which can be found by using the same curve for l'' and IP in eq. (144). Thus we must integrate over the same curve twice in the foregoing expressions for self-energy. It is known from magnetostatics that the coefficient of self-inductance of a line wire having zero cross section makes no sense, as the corresponding double integral diverges. This situation is analogous to that which occurs in the case of a line dislocation in the theory of elasticity, namely, the coefficient L~: for the dislocation having zero cross section is not meaningful. To obtain a finite self-energy we assume that the dislocation is not infinitesimally thin but has some small thickness, i.e, that the single
x
f f R(l: I') [(0" + n,n
k)
dl
ar -
(1
+
v) dl, dlkl
(147)
Let us use eq. (147) and write the self-energy of the dislocation loop in the form
v, ~
ff
B(l, l') dl dl',
(148)
where 8(1, I') has the meaning of a non-local density of the dislocation self-energy. An expression for 8(1, I') follows directly from the formula of eq. (147) 8(1,1') = {[b 2
+ (bn) 2 Jtt' f
Jl
X
8n(1 - v)
- (1
+
v)(bt)(bt')}
fy(~)y(~/) d2~ d2~' R(I, I')
.
(149)
We note that the vector n is taken outside the sign of integration with respect to in eq. (149). Allowance for n in such an integration leads to a small correction to eq. (148) if the ratio of the "thickness" of the dislocation line to the characteristic linear dimension of the entire loop is small. The latter ratio will be assumed to be very small. We can introduce a quantity which has the meaning of the self-energy per unit length of dislocation. Integrate eq. (148) with respect to one of the variables over the loop and write ~ and ~'
v, ~
T
U(I) dl,
U(l)
=
TB(I, I') dl'.
(150)
It is important that the self-energy per unit length of dislocation U(I), introduced in this manner, is not a local property of the point in question onthe dislocation loop. It depends on the dimensions and on the shape of the entire loop. In order to estimate the order of magnitude of U(I), we assume that the function y(~) has a constant value inside a tube of small radius ro, described around the
A. M. Kosevich
94
Ch.l
dislocation line, and equals zero outside this tube. Then there follows from eqs. (149) and (150) the estimate U(l) '"
Jib2
R
4n
ro
-log~,
The dimensionality of the quantity m* is mass per unit length, therefore we can call it the "rest mass" per unit length of a dislocation line. The equations (149) and (150) provide a procedure for calculating the self-energy of a dislocation loop of arbitrary shape. But we shall calculate only the self-energy of dislocation lines of the simplest forms. If we have a straight edge dislocation, then tt' = 1, bt = 0 , bn = 0, and the formula for U(l) may be reduced to eq. (35). b If we 2 . have a straight screw dislocation, then tt' = 1, bt = ± 1, (bn) = 1, and we 0 tam eq. (32). . . Consider a circular prismatic dislocation loop of radius R WIth Burgers vector normal to its plane. Then bt = 0, bn = 0, and the self-energy per unit length, obtained with logarithmic accuracy*, is equal [46J to
c
4n(1 - v)
R
log-· ro
where v = vCr, t) is the velocity of displacement of an element with a coordinate rat the instant of time t. If the dislocations move and the dislocation density varies with time then eq. (154) is not compatible with eq. (116) and we shall therefore replace it with
(155) in which the tensor Jik must be chosen so as to make eqs. (116) and (155) compatible. The condition for the compatibility of eqs. (116) and (155) takes the form of the equation
(156) It is easy to verify that eq. (156) is the differential form of the law of conservation of the Burgers vector in the medium. Indeed, let us consider some stationary closed line s in the medium. We take an arbitrary surface bounded by the line s, and introduce in the formula of eq. (115) the total Burgers vector b of the dislocations that are "coupled" with the surface, that is, enclosed by the line s. Then, we can obtain from eq. (156) in elementary fashion
(153)
The energy of eq. (153) certainly coincides with the energy per unit length of the . straight dislocation, the length of which is of order of magnitude R. The interesting formula for the self-energy of a helical dislocation was obtamed by de Wit [45].
7. Dynamics of a crystal with dislocations 7.1. The dislocation flux density tensor Equation (116), which is the fundamental relation that introduces dislocations into elasticity theory, does not depend on whether the dislocatio~s are s~at~onary or moving. However, it is obvious that in the dynamical case the tune vanat~on of the distortion tensor should be determined essentially by the character of monon of the dislocations.
* The log term
If the dislocations remain stationary when the elements of the medium are displaced we have the obvious equality
(154)
(152)
pb 2 e2
95
(151)
where R is a characteristic radius of curvature of the dislocation line at the point under consideration (in the case of a straight dislocation R; is either its length or the dimension of the body). . . We rewrite eq. (151) in a rather different form using the well-known relatlO~shiP J1 = pc", where p is the density of the medium and e is the transverse velocity of sound. Then we obtain
U =
Crystal dislocations and the theory ofelasticity
in the expression for the self-energy predominates when the radius R becomes large.
(157) From the meaning of eq. (157) it follows that the integral in the right side of eq. (157) determines the magnitude of the Burgers vector "flowing" per unit time through the contour S, that is, carried away by the dislocations that cross the line s. Therefore the tensor Jik can naturally be called the dislocation flux density [47] and eq. (156) is the equation for the continuity of the dislocation flux. Equation (156) was obtained independently by Kosevich [47] and Mura [48J. An equation coinciding in form with eq. (156) was derived by Hollander [49], but it expresses the relationship between somewhat different quantities. The definition of the tensor Jik becomes unambiguous if we note that the dislocation flux density determines directly the rate of plastic deformation of the medium. To verify this, we note that the vector v is the velocity of the total geometric displacement of an element of the medium and determines the rate of the total geometrical distortion uJ: (158)
A. M. Kosevich
96
Ch. 1
With the aid of eq. (158) we rewrite eq. (155) in the form
Crystal dislocations and the theory of elasticity
§7.l
97
It follows from eq. (163) that in the case of parallel dislocations with identical velocities at the point of space in question we have
a T' (U ik - U ik) = -lik'
at
(164)
The difference u~ - U ik determines that part of the total distortion not connected with the elastic stresses, usually called the plastic distortion of the body. Denoting this quantity by Ufk we obtain (159)
Equations (164) and (162) are equivalent. In the case of a continuous distribution of dislocations, the tensor Jik is a continuous function of the coordinates satisfying the condition of eq. (156). The tensor i-; is significant in itself and is a fundamental characteristic of the dislocation motion.
Thus, the change in the tensor of plastic distortion at a certain point of the medium after a short time bt is equal to dl
(160)
~,,---------v
If we write a relation similar to eq. (160) for the plastic strain tensor efk' its form will be
s
(161) A relation equivalent to eqs. (159)-(161), but in a different notation, was indicated by Kroner and Rieder [50]. Let us compare eq. (161) with the expression for the plastic strain tensor eq. (49) caused by a single dislocation and substitute bx = V ot. It is clear that for an isolated dislocation loop the tensor Jik has the form (162)
We may verify the formula of eq. (162) by starting from the physical meaning of the dislocation flux density. We consider a single dislocation with a Burgers vector b, each point of the loop of which moves with a velocity V = VCr), and we calculate the Burgers-vector flux produced by such dislocations when some line s is crossed (fig. 44). If dJ is an element of arc of the line s, and t is the unit vector tangent to the dislocation loop in the vicinity of the point where the line s is crossed, then crossing of the line s by the dislocation loop with transport of the Burgers vector will occur only when there is a velocity component V perpendicular to both dl and t. It is obvious that the number of such crossings of the element dl by the "parallel" dislocation loops per unit time is given by the quantity N(dl x t)V,
where N is the number of dislocations passing per unit area of the plane perpendicular to t. Therefore, the flux of the Burgers-vector component b, through the lines is equal to
1 1 iik
dli =
N(dl
X
t)bk ·
A
Fig. 44 A dislocation AB with tangent vector t moves with speed JIand crosses the element dl of line s.
The average dislocation flux density can be expressed in terms of the same scalar distribution function pP(t) which enters eq. (117):
iik)
= 8 ilm
ff
l,bfv!(t; r)pP(t; r) dO,
(165)
where VP(t) is the average velocity of the dislocation-length elements having corresponding directions of band t, and dO is the differential of the solid angle. Special interest is attached to the connection between the trace of the tensor Jik(JO = Ad and the continuity equation of a continuous medium [47]. The trace j., enters the following equation derivable from eq. (155): div v - (aekklat) = - i;
(166)
It is easy to explain the physical meaning of eq. (166). Indeed, the trace ekk is the relative elastic change in the volume of the medium element, connected in obvious fashion with the corresponding relative change in its density
ekk = -bplp,
(167)
p is the density of the medium. Substituting eq. (167) into eq. (166) and using the linearity of the theory, we arrive at the relation
(163)
aplat
+ div pv = - pJo.
(168)
98
A. M. Kosevich
Ch.l
If the elements of the medium are displaced during the motion of the dislocations without loss of continuity then, by virtue of the continuity equation, the left side of eq. (168) vanishes and ia == ikk
= O.
7.2. The elastic field of moving dislocations Let us set up a complete system of differential equations describing the dynamics of an elastic body in which there are moving dislocations. We assume that the displacement of the dislocation is not accompanied by transport of mass, and take account of the fact that no additional distribution of the concentrated body forces is associated with the dislocation line. Then the equation of motion of the elastic medium can be written as (170) where the elastic stress tensor Pik is connected by Hooke's law eq. (6) with the elastic strain tensor. In eq. (170) we wrote the material time derivative _ aV
-a + (vV)v i = -ati +
ao, Vk - ·
aXk
(171)
Let us substitute eq. (155) into eq. (171) and take into account the fact that the ordinary elasticity theory is linear with respect to elastic strains and rates of displacements. Therefore, we can write d».1 avo dt ~ atl - vkAi'
99
Thus, if the dislocation fluxes are specified, the equation of motion of the elastic medium in the linear approximation has the form (172)
(169)
Comparing eq. (169) with eq. (161), we see that the statement that z, vanishes is equivalent to the statement that the corresponding plastic deformation is not connected with a change in the volume of the body. For linear dislocations, the condition of eq. (169) has a simple meaning. Indeed, in the case of a single dislocation the trace ia is proportional to (b x t) V, that is, it is proportional to the projection of the dislocation velocity on the direction perpendicular to the vectors t and b, in other words, on the direction perpendicular to the glide plane of the dislocation. Thus, eq. (169) signifies that when the medium remains continuous the dislocation velocity vector V always lies in its glide plane and consequently, mechanical motion of the dislocation can occur only in this plane (see sect. 4.). On the other hand, if the dislocation motion is accompanied by formation of certain discontinuities, for example, macroscopic accumulation of vacancies along a section of the dislocation line, then the left side of eq. (168) differs from zero and is equal to the rate of relative inelastic increase in the mass of a certain volume element of the medium (or, accordingly, a decrease in its specific volume).
de, oVi -d = t t
Crystal dislocations and the theory of elasticity
§7.2
In the case of a single moving dislocation the tensor iik is replaced by eq. (162) and in the right part of eq. (172) there appears the term which is proportional to the product vV. Therefore, if terms proportional to v V are taken into account in studies of the dislocation dynamics, then in the right part of the equation of motion (172) the second component should necessarily remain. However, this component is generally omitted and the complete system of dynamical equations of the elasticity theory may be presented in the form: apik aVk - = P -, Pik = CiklmUlm, (173) aXi at (174) If the tensors lX ik and iik are specified, i.e. for specified dislocation densities and dislocation fluxes, the system of eqs. (173)-(174) is complete. The conditions of compatibility of this system are the "conservation laws", eqs. (118) and (156): alX ik -a t
aimk
+ Cilm-a = O. X,
(175)
The system of eqs. (173)-(174) enables us to find Uik (or Pik) and v from any known distribution of dislocations and their fluxes. A system of equations similar to 'eqs, (173, 174) but still different from that given above, was proposed by Hollander [49]. The present system of kinematic equations (174), (175), (158) and (159) coincides with that given in the survey [41J and was employed in the linear theory of dislocation dynamics developed by Kosevich [47, 42J and Mura [48J. The geometrical theory valid for large deformations was developed by Amari [51J. One of the possible ways of solving the system of eqs. (173) and (174) was derived by Nabarro [8J. This method reduces to replacing the infinitely small displacement of an element of the dislocation line by the formation of an infinitely small dislocation loop, and it is convenient when only the time dependence of the deformation field is considered. Perform the differentiation of eq. (173) with respect to time and use eq. (155): (176) We have obtained the dynamical elasticity-theory equation for the determination of the vector v. The vector Pi = Cik1m ailm/aXk in this equation plays the role of the
100
A. M. Koseuich
Ch.l
density of the body forces. The solution of eq. (176) can be represented in the form v,(r, t) =
f dr' fro '§ik(r -
r', t - t')Pk(r', t') dt'
(177)
where ~ik(r, t) is the Green's tensor of the dynamical elasticity-theory equation. Equation (177) completely solves the problem of finding the displacement rates and determines the time dependence of the displacement field. Finally, let us consider the case where dislocation loops are distributed in the crystal in such a way that their total Burgers vector is zero, and the dislocation distribution is described by a dislocation polarization tensor P ik . The dislocation flux density is given in terms of the same tensor P i k by [52, 42] Jik
=
(178)
-OPik/ot.
This is easily seen, for example, by calculating the integral SJik dr over an arbitrary part of the volume of the body, using eq. (162), to give a sum over all dislocation loops within that volume:
fii' dr
= -
:t fPi.
dr.
Comparing eq. (178) with eq. (159), we see, that
c5ufk =
sr.;
(179)
Consequently, in the absence of a resultant Burgers vector in the body, the change in the plastic distortion tensor at each point of the medium is equal to the change in the dislocation polarization tensor at the same point. It must be recalled, however, that there is a fundamental difference between the tensors P i k and Ufk' Whereas the tensor P ik is a function of the state of the body, the plastic distortion tensor is not a function of the state of the body, but depends on the process which has brought the body to the given state. If we agree to regard plastic deformation as being absent in the state with P i k = 0, then, as already mentioned in sect. 6.2., we obtain OUT
U ik
= ~ uX i
P ik,
101
Thus, the question of finding the elastic field produced by dislocations with a zero total Burgers vector reduces to a known problem of elasticity theory. When the plastic polarization tensor P ik is specified, the vector u T can be determined from the dynamical elasticity equation expressed in terms of displacements, in which the density of the body forces is J; = - Cikl l1l oP II1l/OXk. The solution of eq. (182) can be written similarly to eq. (177), namely
u,T() r, t = ckl mn
fd 'ft r
,£! ;';1ik( I'
-
I 1',
er; d'
t - t -0- t. ')
(183)
Xl
-00
Equation (183) in conjunction with eqs. (180) and (181) completely solves the problem of finding dynamical displacement and strain fields, and the rates ofdisplacement.
7.3. The stress field in the linear approximation of the dislocation velocity Assume that the dislocations occupy a certain part of the elastic medium, moving with small velocities V in a region with linear dimensions L. We shall assume that V « c, where C is the speed of sound in the medium, or, to put it another way, L « A, where A is the characteristic length of the sound wave generated by the motion of the dislocations, and expand all the quantities of interest to us in powers of the delay time of the sound waves inside the dislocation system, confining ourselves to the first terms of the expansion. Such an expansion is valid both inside the dislocation system and at distances R ::::: L from the system. We write down the stress tensor in the form Pik = p~~) + P~t), where p)f) denotes the quasistatic stress field obtained when the delay is completely neglected, and p~i) is proportional to the time derivatives of the dislocation polarization tensor and describes the dynamical effects. We shall not write out in an explicit form the quasistatic part of the stress tensor, since it is treated widely in the literature [6, 43]. We note, however, that this part of the stress tensor can be represented in the form
(180)
where u T is again the vector of the total geometrical displacement from the position in the undeformed state. The rate of displacement v is in this case connected in the usual fashion with the time derivative of the vector u T :
v = OUT/ot.
Crystal dislocations and the theory of elasticity
§7.2
(181)
We substitute eq. (180) and (181) into the equation of motion (173) and use Hooke's law: (182)
R
= II' - 1"1,
n = (I' - r')/R,
(184)
where the fully defined tensor function qiklm('n) contains only the components of the vector n and dimensionless factors of the order of unity. As to the dynamical part of the tensor P ik» we represent it in a shortened form as [53] (1) _
Pik
-
p 0 4n ot
f
R (). (') fJiklm n IJl m r
dr' R'
(185)
A. M. Kosevich
102
Ch.l
where the tensor fJiklm(n) in an isotropic medium is connected with the components of the vector n by the relation fJiklm(n) = t[(1 - 2y2
+
Z
+
in, bk1 + nk bil)nmJ
1=
y4)(b il bkm + bim bk1)·
Here y2 = c; Ic;; Ct is the transverse velocity and c, is the longitudinal velocity of sound. For simplicity we have confined ourselves to the case Ak = 0, assuming that the dislocations move in their slip planes. In an anisotropic medium eq. (185), naturally, remains valid and the connection between the tensor fJiklm(n) and the elastic moduli of the medium has been determined for the general case by Kosevich and Natsik [54].
103
energy radiated by the system of moving dislocations in an isotropic medium is equal to [47J
3y4)bik - 3(1 - y4)ninkJnznm
- t y4[(ni bkm + nk bim)n + i(1 +
Crystal dislocations and the theory of elasticity
§7.4
5~C
HGJ [jj~I
+ [jj~J}
(187)
The bar in eq. (187) denotes averaging over a region of space whose dimensions exceed the radiation wave-length. The radiation of elastic waves by a system of moving dislocations in an anisotropic medium can also be considered in a general form [52]. The radiation by a single straight dislocation can be obtained more simply by using other methods. Eshelby [55, 56J has considered the radiation from a screw dislocation. Formulae for the radiation from a straight edge dislocation can be derived from the results by Kiusalaas and Mura [57J*.
7.4. The radiation field of moving dislocations Let us consider the deformation produced in an unbounded isotropic medium by a system of moving dislocation loops at large distances R considerably in excess of the dimensions L of the system. We assume that the speed V of the dislocations is small compared with the velocity of sound C in the solid. Then the ratios LIR and Vic are small parameters, characterizing the deformation field. We confine ourselves to the first nonvanishing terms of such an expansion, assuming the smallness of both parameters to be of the same order of magnitude. We choose the origin somewhere inside the system of dislocations and denote by R o the distance from the origin to the point of observation (no is the unit vector in the appropriate direction). Then by virtue of the smallness of the dimensions of the system, we can put R ~ R o - r'n., in expressions similar to eqs. (177) and (183) and expand the integrand in powers of r'n. We confine ourselves to the case Ak = O. Then, at distances R that are large compared with the wavelength of the emitted elastic waves (R o » cLIV), the displacement vector in the radiated sound wave has the form [47J 1 u = -2-ncRo
{(C-
t)3.
n[nDJt
Ce
+
.
.}
[D - n(nD)Jt '
(186)
where the dot denotes differentiation with respect to time. The vector D in eq. (186) denotes the "projection" of the symmetrical part of the total dislocation moment tensor D ik (see sect. 6.2.) on the direction of n: D,
= nkD~i'
D~k
= i(D ik + DkJ·
The square brackets with the subscript t in eq. (186) enclose the quantities taken at the instant of time t - Rolcp where Ct = C is the transverse velocity of sound. The square brackets with the subscript t in eq. (186) contain quantities taken at the instant of time t - Rolce, where Ce is the longitudinal velocity of sound. With the aid of eq. (186), using the well-known formula for the flux density of sound energy [10J, we calculate the intensity of radiation. The total elastic-wave
8. Equation of motion ofa dislocation 8.1. The field nature of the equation of motion of a dislocation The system of eqs. (173)-(174) formulated in sect. 7.2. determines the elastic distortion tensor Uik and the material displacement velocity vector v from the known distribution of the dislocations and their fluxes. The tensors (Xik and Jik' describing the motion of the dislocations, are assumed specified. In order for the system of eqs. (173)-(174) to be completely closed and descriptive of the self-consistent evolution of the dislocations and of the elastic field, it is necessary to show how the densities ofthe dislocations and of their fluxes vary under the influence of elastic fields. In other words, it is necessary to derive an equation of motion for the dislocations. By virtue of the definition given above for a dislocation, the equation of motion of a dislocation should be derivable from a field. The field-theory aspects of equations of motion and of the corresponding masses are universally known and will not be developed here. There are many ways of deriving the equation of motion of a dislocation. In the survey [42J the author discussed in detail the derivation of this equation by analogy with the Lorentz derivation of the equation of motion of the electron, i.e. starting from the notion of self-action of the dislocation. We present only the final result of the derivation [53]. Let us consider a dislocation element, which has a tangent vector t and moves with a certain velocity V. The motion of this element takes place subject to the condition that CikltkPlmbm
+
pvb(t x V)i
= 0,
(188)
where all the quantities are taken at the point at which the dislocation element is situated. * See Addendum 7.4.
104
A. M. Kosevich
Ch.l
The tensor Pik and the vector v contained in eq. (188) include both the external elastic field and the self-field of the dislocation loop. Thus, eq. (188) relates the dislocation self-field, meaning also the dislocation-loop motion that generates this field, to the external fields. Inasmuch as the external fields in eq. (188) are taken at the same point of space, at which the dislocation element under consideration is situated at the given instant of time, eq. (188) is an implicit equation of motion of the dislocation. The expression (189) which when set equal to zero constitutes the equation of motion (188), determines the total force exerted on' a unit length of the dislocation. The same equation was obtained by Rogula (58] in the model called the model of a "pseudo-contiauumvby.using a different technique. In order for the equation of motion (188) to have the usual explicit form, that is, for it to relate the instantaneous coordinates and velocity of the dislocation with the instantaneous value of the external stress field, it is necessary to express the selffield of the moving dislocation at some instant of time in terms of the coordinates and velocity of the elements ofits loop at the same instant of time. We know that this can always be done it) the-approximation that is linear in the dislocation velocity, if the set ofequations (173) alfd(l74) is used. In the discussion ofthe set of equations (173)-(174) it was noted that eq. (173) can be obtained from eq, (170) if the terms proportional to vV are omitted. Therefore, following this approximation, we should omit the second term in the right-hand side of eq. (189) and write : (190) Details concerning the form of the expression giving the force of elastic origin which acts on the moving dislocation have been discussed by many authors. An analysis of this discussion is given in the paper by Malen [59]. Before discussing the explicit form of the equation of motion and introducing the effective mass ofthe dislocation it should be noted that the equations of motion (188) or (190) involve only nondissipative forces of elastic origin. As to the motion of a real dislocation, it should be said that this dislocation experiences also some forces of inelastic origin.
Crystal dislocations and the theory ofelasticity
§8.2
105
dislocation stresses. We transform the self-force F(flS) in eq. (190), assuming the dislocation line to be not infinitesimally thin, but of some finite thickness, with a Burgers vector which is "smeared" over this thickness*. Then by using eq. (146) we can write the force of self-action F(pS) in the form:
fP~mY(~) d2~.
F,U)') = B'kltkbm
(191)
We now use for the tensor P~k an expansion in powers of V and represent it as a sum of two terms: P~k = p~Z) + p~~), the first of which p~Z) determines the quasistatic stress field, and the second one P~t) the stresses proportional to the acceleration of the dislocation. The term p~2) characterizes the linear self-tension of the static dislocation loop. This force can be easily calculated by substituting in eq. (191) the static expressions for p~Z). Since this operation is perfectly obvious, and since the quasistatic tension force of the dislocation loop has itself no bearing on the question of interest to us, that of the effective mass of the dislocation, we shall not write down an explicit expression for this force. We note, however, that the self-tension force corresponds to a definite self-energy of the dislocation at rest. The second part of the self-action force is determined by the term p~~) and can be expressed with the aid of eq. (185) in terms of the dislocation acceleration. Before we write this expression, we shall make two remarks. Firstly, the mechanical motion of the dislocation along the glide surface presents the greatest interest since this motion can occur with large velocities and accelerations. The displacement of the dislocation along the normal to the slip plane can go quickly only in the case of the dynamical development of a crack. However in the latter case the continuity of the medium is broken. We shall not discuss such problems here, and shall confine our consideration to dislocation glide. Secondly, in writing down the dynamic self-action force of the linear dislocation we shall be interested only in the terms having a logarithmic singularity. With such considerations it is possible to separate the main part of the force F(pS) within a logarithmic accuracy, which is quite sufficient for us. Then, substituting in eq. (191) the indicated part of P~t), we can write for the corresponding part of the self-action force F/jj(l»)
~
f
1',,(/, I') Wi I') dt',
-
W(l) = V(l),
(192)
where W(l) is the acceleration of the dislocation element and 8.2. The explicit form of the equation of motion of a dislocation
In order to have the equation of motion of the dislocation in the usual form, it is necessary to separate explicitly in eq. (188) the force of self-action of the dislocation, and to exclude the singularities of the dislocation self-field, in a similar way to that which is done ill the derivation of the field mass and the equation of motion of an electron by the Lorentz method. To take the self-action into account, we represent the field Pik in eq. (190) in the form Pik = P~k + P~k' where P~k is the external field, and P~k is the self-field of the
1',,(/, I') b cos
~ tPb (tf li" 2
e = nb,
1 r(l,I') = 4n
ff
n
- t;t,{
1+ (~T 0] tu, sin?
= [x(l) - x(l')]jR(l, 2
I'),
t
1'),
= t(l), t' = t(l'),
2
;: d (' y(~)y(~') dReI, I') .
(193)
* It is obvious that, as in the case of static dislocations, the self-action of moving strictly linear dislocation; (that is dislocations with zero thickness) is described by divergent integrals.
Ch.1
A. M. Kosevich
106
We note that in eq. (193) as.in eq. (149) the vector n is taken outside the sign of the integration with respect to ~ and ~/. The expression for flik(l, 1/) in an anisotropic medium was obtained by Kosevich and Natsik in [54]. Substituting eq. (192) into eq. (190) and taking into account.the.presence of forces of inelastic origin, which were mentioned above, and which also act on the dislocation, we write down the final form of the equation of motion of the element of the dislocation loop:
t
Jlik(l, I') Wk(l') dl'
~ F,o(l)
+ "'km t k(l)P~n(l)bn +
S ,(l, V)
(194)
where Fa is the already-mentionedquasistatic dislocation self-tension, and S is the force of inelastic origin, which, naturally, depends on the dislocation velocity. It is important to note that the inertial term in the equation of motion, that is, the left side of eq. (194), plays an important role only in the case of sharply nonstationary motions of the dislocation, when the acceleration of the dislocation is very large. If the acceleration of the dislocation is small, then the major role is played by deceleration forces (resistance forces), which include the dissipative forces. It is the magnitude and the dependence on the dislocation velocity of these forces which determine essentially the character of the almost-stationary motion of the dislocation. We now consider explicitly a dislocation which moves along its glide surface. We introduce at each point of the dislocation line a right-hand triplet of unit vectors (t, 'V, K), v being the vector normal to the glide plane and K the vector normal to the dislocation line in the glide plane. A contribution to the self-action force is made only by the dislocation velocity (or acceleration) component perpendicular to the dislocation line. In the case in question, these components are equal to
Therefore, multiplying eq. (194) by tJl(I, I')W,(I') dl'
K,
we obtain
~ Fo(l) + vm(l)p~"(l)bn + S(l, V,),
(195)
=
iPb2(tf')(KK'{ 1
+
GJ
sin?
J
e
T(l,l').
(196)
An expression in lieu of eq. (196) for fl(l, 1/)in an anisotropic medium was obtained in [54]. Equation (195) describes the mechanical motion of a dislocation loop in an external stress field. In the derivation of the equations of motion of the dislocation we used eq. (185), which is the second term in the expansion of the dynamic dislocation field in the delay of the elastic waves, i.e. formally in powers of lie. Consideration of the next terms of this expansion allowsus to calculate the retarding force due to radiation of sound
107
waves by a nonuniformly moving dislocation. Natsik [60J has shown that this force is similar to the corresponding radiation force for a nonuniformly moving electric charge and is proportional to the time derivative of the dislocation acceleration.
8.3. The effective mass of a dislocation can conclude from eq. (194) that flik(l, 1/) has the meaning of the nonlocal effective field mass density of a dislocation line. The physical meaning of the tensor function flik(l, s) is that it establishes the contribution made by the kth component of the velocity of the element with coordinate s on the dislocation loop to the ith component of the momentum of an element of unit length with coordinate I on the same loop. The physical meaning of the quantity flik(l, 1/) can be described from a somewhat different point of view by writing down the kinetic energy of the dislocation loop Ek'n
=
(197)
i f f Jlik(l, I') V,(I) ViI') dl dl'.
From eq. (197) the obvious symmetry of the tensor flik(l, s) follows which, naturally, is implied in its definition in eq. (193): (198) If we compare flik(l, 1') with the expression for the density of the dislocation selfenergy eq. (149), we can easily verify that flik(l, 1') and 8(1, 1') have a similar functional dependence on position on the dislocation loop, and that in order of magnitude fl(l, 1')e2 '" 8(l, 1/).
The concrete expressions, however, are different and therefore the dynamical nonlocal mass density does not reduce in the general case to a nonlocal "rest mass" density. Only for a straight screw dislocation do we have 2 flik(l, 1')e
where for an isotropic medium we get with logarithmic accuracy Jl(l, I')
Crystal dislocations and the theory of elasticity
§8.2
= bik8(l, I').
Along with the equation of motion of the dislocation element eq. (194), we can consider the averaged equation of motion of the entire dislocation loop by integrating eq. (194) over the loop tm'k(l)Wk(l) dl = F,',
F,' = "ikmbn
ttkP~n dl +
ts,
dl
(199)
where Fe is the total external force acting on the dislocation, and m'k(l) = tJl'k(l, I') dl'.
(200)
The first term in the right side of eq. (194) drops out after integration over the entire loop, since the total self-action force of a dislocation at rest is equal to zero. If the applied stress is uniform, there is also no resultant elastic force on a closed dislocation loop. If the stress field varies only slightly over the loop, the total elastic
A. M. Koseoich
108
Ch.l
force acting on the dislocation and entering into eq. (199) is determined by the elastic stress gradient [14]. It follows from eq. (199) that when the motion of the entire dislocation loop is considered, mik(l) plays the role of an effective mass per unit length of the dislocation. It is obvious, however, that the effective mass per unit length of the dislocation, introduced in this manner, is not a local property of the point in question on the dislocation loop. It depends on the dimensions and on the shape of the entire loop. Using eq. (200) and the definition of the tensor /lik in eq. (193), let us estimate the order of magnitude of m ik. For such an estimate we shall assume that the function y(,) takes a constant value inside a tube of a small radius r0' including the dislocation line, and is equal to zero outside this tube. We can then readily obtain the estimate m '"
pb 2
R
4n
ro
-log~,
(201)
where R, is the characteristic radius of curvature of the dislocation line at the point under consideration. In the case of the rigid motion of a straight-line dislocation, R, is the dislocation length. If the dislocation oscillates, then R, is equal to the wavelength of the bending oscillations of the dislocation line [61]. In order of magnitude m ik '" m*, where m* is the rest mass per unit length of the dislocation defined by eq. (152). The estimate obtained for m ik justifies our assumption of a pure field mass for the dislocation. The point is that when a real dislocation moves in a crystal, it sets in motion also some of the atoms in the vicinity of the dislocation axis, at a distance of the order of r0 from the axis. This produces an additional dislocation inertia, connected with the ordinary mass of these atoms. The order of magnitude of the mass of the atoms inside a tube of radius r0 '" b can be estimated as pr6 '" pb 2 per unit length of the dislocation. Comparing this estimate with eq. (201) we see that when log (Relr 0) » 1, taking into account the masses of the moving atoms near the dislocation line does not noticeably change the dislocation inertia, and the dislocation mass can be actually regarded with logarithmic accuracy as a field mass. For a straight-line dislocation, when the vectors t and b are constant along the dislocation line, the tensor m.; is described by the very simple expression
(202) where R m denotes the length of the dislocation. In the case of a screw dislocation, eq. (202) leads to the expression previously derived for the screw-dislocation mass by Frank [62J and Eshelby [56]. Finally, let us consider the motion of a dislocation loop as a unit, (203)
Crystal dislocations and the theory of elasticity
§8.3
109
by introducing the average acceleration W o of the dislocation loop and the tensor of its total mass M ik , defined by the formulae
MikW~ =
fmik(l) Wk(l) dl,
u.; ~
fmik(l) dl.
(204)
The equations of motion (194) and (203) enable us to separate the study of the motion of the dislocation loop as a whole from the study of the relative motion of its elements. Having derived the equation of motion of the individual dislocation, we have, in principle, a complete system of equations defining the evolution of a set of dislocation loops and the elastic field in the solid. However, the dislocation equations of motion in this system are equations of motion of the discrete structures. Yet the entire theory of the dynamic elastic field produced by the dislocations has been formulated in terms of a continuous dislocation distribution. A natural way of recasting this system of equations in a unified form is to average the equations of motion of a large number of individual dislocations and to transform them into equations of motion of continuously distributed dislocations. This problem was discussed in the survey [42]. 8.4. Dislocation damping in a medium having dispersion of the elastic moduli
Dislocations moving in a crystal always experience a damping force, leading to energy loss. It is necessary to take this force into consideration when we write the equation of motion of the dislocation. There are many mechanisms of dissipation which retard the motion of a dislocation. Some of these relate to the discrete structure of the crystal and the detailed structure of the dislocation core. However, there exists a damping mechanism which can be analyzed by considering the crystal as a continuous medium. It relates to the mechanism whereby dislocation energy is dissipated due to relaxation processes occurring in the deformation field of the moving dislocation. The corresponding energy loss should be considered within the framework of the continuum theory of moving dislocations. Unfortunately, there is at the present time no systematic theory for the dislocation damping produced by the discrete structure of the crystal, so that it is not possible to determine in all cases the relative importance of the contribution from relaxation mechanisms to the dislocation damping force. We can only expect that the dislocation energy loss by relaxation processes will be quite substantial for a dislocation velocity V lying in the range c(a s / /l) 1/2 « V « c, where as is the "starting stress" for initiation of dislocation motion, /l is the shear modulus of the crystal (/l » as always), and c is the velocity of sound. The lower limit of this range is determined by the following condition: in the range of dislocation velocities of interest here, the kinetic energy of the dislocation should substantially exceed the rise in the interatomic interaction potential, which determines the starting stress. Regarding the high velocity limit, it is connected in a natural way with the fact that at V '" c the motion of a dislocation should be described by theories of a discrete crystal lattice, and not by a macroscopic theory. In other words, at such velocities the dislocation retardation should be essentially determined by that component of the dislocation damping which is
110
A. M. Koseoich
Ch.1
directly connected with the atomic structure of the material and not with its average properties. In the indicated dislocation velocity range, where the relaxation energy loss can be substantial, it makes sense to analyze it separately. The justification for such a separation of the macroscopic damping force is as follows. In the first place, each relaxation mechanism is characterized by its own specific relaxation time r, which depends on the state of the crystal (in particular, on its temperature), and, generally speaking, is unrelated to the characteristic lattice frequencies: therefore, with dislocation velocities of order V "" ali, where a is the lattice constant, we would expect an increase in the damping force due to these relaxation mechanisms. The -position and size of the corresponding maximum or region of nonmonotonic behaviour in the velocity dependence of the damping force is determined by the state of the crystal (for example, its temperature), and consequently should change in a controllable way. In addition, it is possible to have relaxational energy loss connected with contamination of the crystal, i.e. with the presence of impurities. The contribution of these losses to the damping force, on the one hand, depends on the impurity concentration, and therefore in principle can be separated from the others. On the other hand, such losses sometimes can have a peculiar, almost resonant, nature, if the impurities have quasidiscrete eigenfrequencies, and this should generate specific features in the dependence of the damping force on the dislocation velocity [63]. Additional damping mechanisms due to relaxation phenomena in the elastic field of a moving dislocation have been analyzed previously by various authors. Eshelby studied thermoelastic absorption of energy related to the thermal conductivity of the medium (thermoelastic friction) during the vibrational motion of edge dislocations [55J, and also found the damping force on screw dislocations moving in an isotropic viscoelastic material (the so-called "standard linear medium") [64]. Schoeck and Seeger have considered [65J the dissipation of energy due to local changes in the order near dislocations in a solid solution. Mason [66J has estimated the effect on dislocation damping of the exchange of energy between the various branches of the phonon spectrum, which come into equilibrium with each other during the deformation (phonon viscosity)". Here we present a theory of relaxation damping which does not particularize the relaxation mechanisms and is valid for crystals of any symmetry. The method of calculation used for the damping forces is similar to the electrodynamic calculation of the ionization loss of a charged particle passing through matter. It is known that the presence of relaxation of the elastic stress in a continuous uniform medium leads to dispersion of the elastic moduli [67]. This means that Hooke's law for such a medium in a literal sense can only be written for stresses Pik and strains eik varying harmonically in time, P, e o: exp [ - iwtJ: (205) The components of the elastic modulus tensor Cik1m(W) are, generally speaking, complex functions of the frequency co. Just as the presence of an imaginary part of
* See also Ref. [127].
§8.4
Crystal dislocations and the theory of elasticity
111
the dielectric constant in a medium leads to absorption of energy from electromagnetic waves, the imaginary parts appearing in the components of the tensor Cik1m(W) lead to the absorption of sound vibrations by the medium, i.e. cause their energy to be dissipated. The relationship between the internal friction and the dispersion frequencies of the elastic moduli of isotropic media has been analyzed by Zener [67]. In those cases where it is necessary to take into account spatial dispersion of the elastic moduli also, an equation of the type of eq. (205) should relate a stress and a strain whose dependence on space and time is of the form exp [i(k,. - wt)]. In other words, the elastic moduli should be considered to be functions of the frequency w and the wave number vector k, and Hooke's law should be written in the form Pik
=
Cik1m(W,
k)e 1m ·
This spatial acoustic dispersion should be taken into consideration when subsonic, "transonic" and supersonic motion of the dislocation is analyzed [68, 69J*. It is clear that the damping force on a dislocation in a medium with dispersion of the elastic moduli can be expressed in terms of complex elastic moduli. In order to carry this out it is necessary to calculate the elastic stress created by a moving dislocation in such a medium and to determine the force exerted by this field on the dislocation. This problem is solved by Kosevich and Natsik [70J for a straight dislocation moving with a constant velocity in the medium with an arbitrary symmetry. In an isotropic medium the damping force can evidently be expressed in terms of the complex elastic moduli. We assume that the mechanisms which give rise to dispersion of the elastic moduli have negligible spatial dispersion. Then the dispersion of the moduli leads only to a frequency dependence: A = A(W) and j1 = j1(w). The damping forces on an edge dislocation FE and screw dislocationF, have the forms [70J : F = - ibi J~ (kV) A(kV) + j1(kV) dk E n · Ikl j1 A(kV) + 2j1(kV) ,
ib~
F s = - 2n
J1kfk j1(k V) dk,
(206)
where bland b 3 are the Burgers vectors of the edge and screw dislocations, respectively. We separate the real and imaginary parts in the right-hand sides of eq. (206). From general consideration, it follows [67J that the real parts of the complex elastic moduli should be even, and the imaginary parts odd functions of w; therefore, the real parts of the integrands in eq. (206) are odd, and their integrals over all values of k are zero. The imaginary parts of these integrands are wholly due to dispersion of the elastic moduli and will be even functions of k. Consequently, we can double the integrals and integrate over positive values of k. In speaking of the integrations in eq. (206), which take into account all possible values of k, it is appropriate to estimate the upper limits of these integrals. We know that the following proportionalities usually appear for very high frequencies w:
* See Addendum 8.4.
A. M. Koseuich
112
Ch.l
Im A OC ljw and Im u o: ljw; therefore, eqs. (206) are logarithmically divergent for large k, i.e. for large k V. In order to understand the physical reason for this divergence,
we note that integration over very large k values corresponds to considering the deformation in a very small neighbourhood of the dislocation core, where the lattice distortion cannot in principle be described by elasticity theory. The contribution to the damping force from deformation in the immediate vicinity of the dislocation core should be considered within the framework of microscopic models, which is not our aim. Rogula [69J showed that a reasonable formulation of the model of the elastic continuum having acoustic dispersion eliminates the divergence of integrals of this kind. In order to take into account correctly the range of applicability of the ideas used, and eliminate the non-physical divergence of the integrals, it sufficesto cut off the integration at some wave number k = k o, where k o is of the order of magnitude of the inverse linear dimension of a dislocation core (kob '" koa '" 1). In an isotropic medium it is convenient to transform from complex elastic moduli to quantities having a direct physical meaning, namely, to the attenuation coefficients and phase velocities of sound waves. We consider the case where the absorption has a nonresonant character and it is small in the frequency interval of interest (0, k o V). This dispersion of the phase velocity of sound is also small and we can assume this velocity to be the usual isothermal velocity of sound waves. Then [( 1 - 2c?) F E = - -4pbic; -
c;
nV
2pb~c;
f.kOV --dw+ytCw) Ct f.kOV ylw) ] --dw, co
0
cf
0
co
(207)
f.kOV
ytCw) (208) --dw nV ° co ' where ytCw) and yl w) are the attenuation coefficients per unit distance for a transverse and longitudinal sound wave, respectively*. In a real crystal several different relaxation mechanisms can act simultaneously, leading to dissipation of elastic energy. Each of them gives a certain contribution to the absorption and dispersion of sound, and consequently to the damping force on a dislocation. If we limit ourselves to the consideration of frequency dispersion, then for sufficiently general assumptions each dissipation mechanism can be described by its own relaxation time T j and contributes a term of the following form to the sound absorption coefficient: Fs
= ----
W
y/w) = A j 1
Crystal dislocations and the theory of elasticity
§8.4
113
Using formulas of the type of eq. (209) for the sound absorption coefficient we can carry out a qualitative analysis of the way in which the dislocation damping force depends on the velocity. Since the absorption from relaxation processes has, as a rule, a small value (Ac « 1), the calculation of the damping force can be carried out without considering the dispersion of the phase velocity of sound, i.e. using eqs. (207) and (208). We will consider the relaxation time to be independent of frequency and substitute eq. (209) into eqs. (207) and (208). In the result it turns out that the force of relaxational damping is described by a sum of expressions of the form b2 p C3
F.(V) '" A. --log (l J J TjV
+
k~TJ V 2).
(210)
We will estimate the order of magnitude of the second term in the logarithm in eq. (210). Note that koTV '" V(Tja). For all relaxation processes of a macroscopic nature at velocities V « c the quantity koTV can have, generally speaking, a value of the order of or greater than unity. Thus, even for comparatively low dislocation velocities it is possible to have a nonlinear dependence of the damping force on the velocity V. The nonlineardependence of eq. (210), as can be easily seen, leads to the appearance of a maximum in the relation Fj = F/V) at velocities V '" Ij(koT j). The damping force due to those mechanisms for which the inequality koTV:> 1- is fulfilled simultaneously with the inequality V« c, after attaining a maximum, falls off as IjV. Figure 45 shows the characteristic function which describes the dependence of the damping force on velocity: F(V) = const l/J(koT V), where I/J(x) = (ljx) log (1 + x 2 ) . Note that the nonmonotonic dependence of-therelaxational damping force on the velocity, even in the comparatively low-velocity region, has been emphasized by Schoeck and Seeger [65J, and also by Eshelby [64]. If the dislocation velocity V and the relaxation time Tj are such that kOTjV « 1, then the expression for the corresponding term in the damping force has the-order of magnitude F, '" pc3b2k~AjTjV '" pc 3A jTjV, and the relaxation damping force is proportional to the dislocation velocity. In other words, the damping is described by the usual resistive force F = - (X2 V, where the
2T.
+ W ~ T 2'
(209)
1.0
j
If several relaxation mechanisms act simultaneously, with different relaxation times, the absorption coefficient is described by a sum of terms of the type of eq. (209). The quantity A j which enters in eq. (209) depends on the structure and state of the medium, and also on the form of the relaxation mechanism. In addition, both A j and the relaxation time T j have different values for longitudinal and transverse sound waves.
* If the dispersion law for sound waves is represented in the form coefficient y(w) is defined as the quantity y(w)
=
1m k(w).
0.5
o
5
x
10
k = k( w), then the attenuation
Fig. 45 Graph of the function t/J(x)
= (l/x)
log (l
+
x2 ) .
Ch.1
A. M. Koseoich
114
coefficient ry.2 is naturally proportional to the relaxation time r. However, judging from the dependence shown in fig. 45, we should expect that for low velocities (k o Vr « 1) eq. (210) should be used only for coarse quantitative estimates. Actually, in this case the force F is very sensitive to the choice of the parameter k o , which cannot be precisely determined. Also, with koT: V :> 1 the dependence of the calculated force F on this parameter is only logarithmic, i.e., very weak; therefore, strictly speaking, eq. (210) is valid with logarithmic precision and usable in explaining the quantitative dependence only for dislocation velocities V :> air.
There exist many dynamical problems in dislocation theory which can be analyzed by using the so-called string model. This model treats the dislocation line as a heavy string under tension lying on a "corrugated" surface. The corrugated surface describes the Peierls potential. Troughs of this surface correspond to the potential minima on the glide plane occupied by a straight-line dislocation in equilibrium (fig. 46).
- - - - -I - - - l l = a
- - - - -
Max-------
1]
=
Min~l DIslocatIon x
(a)
(b)
Fig. 46 Two types of the motion of a dislocation in the field of the Peierls potential. (a) The dislocation oscillates in its own trough. (b) The dislocation forms a kink moving along the x-axis.
1]0
w2
=
w6 + c6 k 2 ,
21] 21] 0 0 . ( 1]) m ot 2 - T D ox 2 + bo.; sm 2rc -;; = ba,
(211)
where a p is the Peierls stress and a is the corresponding component of the applied stress. The properties of this equation have been discussed by a number of writers [71J. Equation (211) is a non-linear equation which describes rather well dislocation displacements 1] of the order of magnitude of the lattice period. In the absence of an external field a, the dislocation motion takes the form of free oscillations corresponding to the normal modes of vibration of a stretched string. Since the system is non-linear, these oscillations cannot be directly superposed. The lowest modes of these motions are small-amplitude disturbances, when the dislocation oscillates in one trough of the Peierls potential (fig. 46a). In this case 1] « b and the equation of free oscillations reduces to
0ot1]2 2
m
0ox2 + 2rc (b)-;; a 2
TD
1]
p1]
= O.
(212)
(214)
where (215)
= Znbo pima,
Other simple modes describe motions of the dislocation when one end of the dislocation (x = - (f) is situated in one trough of the Peierls potential (1] = 0) and the other (x = (f) is in the next trough (1] = a). This situation is shown in fig. 46b and corresponds to the motion of a single kink on the dislocation (see sect. 4.3.). It.is evident that a kink travelling along the dislocation is described by a solution of eq. (211) satisfying the conditions (f)
= 0,
(216)
= a.
1](00)
It is interesting to note that the solution of eq. (211) under the conditions ofeq. (216) is equivalent to the problem ofthe motion ofthe dislocation in the Frenkel-Kontorova model [73J. A single kink moving with a constant velocity v along the x-axis initiates transverse displacements of the dislocation 2a
Let the x-axis be directed along the equilibrium position of a straight dislocation, and the transverse displacements of the dislocation 1] go along the y-axis in fig. 46. If the dislocation has a mass m per unit length, line tension T D and is subjected to a Peierls potential (see sect. 5.5.), the equation of motion of that dislocation has a form
(213)
sin (kx - wt),
which have the dispersion law
1]( -
Max
115
Leibfried [72J used eq. (212) in considering the thermal motion of the dislocation. The solution of eq. (212) describes sinusoidal oscillations of the type
w6
8.5. The string model
Min - - -
Crystal dislocations and the theory of elasticity
§8.5
1](x, t) = ~ tan
-1
exp
x - vt
(0 _ v2 /C~)1/2 '
(217)
where Co is determined byeq. (215) and
( = co/WOo
(218)
The quantity ( may be called the half-width of the stationary kink. The total energy of the moving kink depends on its velocity v and is [74J
Wk =
f
oo
-00
[1zp (01])2 1 (01])2 ab ot + zT ox + ~ a D
p
.
2rc1]]
sin -; dx
= Wo/O - v2 /C6)1/2,
(219)
where W o = (2/rc 2 ) (a 2 T D j( ) is the energy of the stationary kink. If v « Co, the kink energy of eq. (219) may be written in the form Wk(v) = W o
+ !M kv2 ,
(220)
where
M; = W o/c6· It is natural to call the quantity M k the mass of the kink [74].
(221)
116
A. M. Koseoich
Ch.l
Thus the kink can be considered as a particle constrained to move along the dislocation and having the mass M k • The kink motion along the dislocation causes a transverse displacement of the dislocation. Therefore the kinetics of a set of kinks on the dislocation determines one of the possible mechanisms of dislocation motion under weak applied stresses. Now consider dislocation vibrations effected by an external oscillating force under conditions where Peierls-Nabarro forces may be neglected* and where allowance for the damping force proportional to the dislocation velocity becomes essential. In this case the motion of a dislocation is governed by an equation similar to eq. (211) in which the term coming from the Peierls potential is omitted and the damping term B(a1]/ot) is added, where B is a certain factor dependent on the nature of the dissipative forces. As a result we have the equation m
0
21]
ot
0
2 -
21]
To ax 2
+
B
01]
at = ba., e
- icot
.
(222)
Suppose that the dislocation is pinned by point impurities at x = ±il. Then the solution for a forced vibration of the dislocation segment is 1]
= b(Jo e- icot (cos kx _ 1)' k 2 To
cos ikl
(223)
117
Crystal dislocations and the theory of elasticity
§9.1
Consider for definiteness a simple cubic lattice of a dielectric or metal crystal. An interstitial atom in that lattice leads to such a local distortion of the perfect crystal that all atoms nearest to the interstitial atom are displaced outwards from the interstitial atom (fig. 47a). In a simple cubic lattice this deformation has a cubic symmetry due to the fact that the atoms in the nearest neighbourhood of the interstitial atom experience the action of very symmetrical repulsive forces. The system of these forces has, naturally, a zero resultant and a zero total twist moment. From the macroscopic point of view their action is equivalent to the action of three equal double forces without moment located in the position of the interstitial atom and directed along the coordinate axes (fig. 47b). In elasticity theory this system would be described by a density of body forces in the following form (the defect being placed at a point r = r o) [10, 40J: fer)
=-
KD o grad
oCr - r o ) ,
(224)
where K is the bulk modulus and the quantity Dois equal to the increase in the crystal volume due to the presence of a single interstitial atom in the crystal. An additional atom may only increase the crystal volume and hence, Do > O. The volume change produced by the interstitial atom is usually of the order of magnitude of the atomic volume, therefore, [20 "-' a 3 •
where k 2 = (mw 2
+ iBw)/To·
Equation (222) and its solution eq. (223) are the basis of the dislocation theory of internal friction suggested by Koehler [75] and extended later by Granato and Lucke [76J.
(a)
Fig.47
9. Dislocations and point defects
(b)
A model of an interstitial atom. (a) Atom displacements near the inclusion in a simple cubic crystal. (b) The equal double forces without moment.
9.1. Elastic interaction of dislocations with point defects
A point defect is usually understood as any distortion or imperfection of the crystal lattice concentrated in a volume of the order of magnitude of the atomic volume. However, our present analysis is limited to the most trivial types of point defects in the crystal without impurities. Such are interstitial atoms and vacancies. For most problems dealing with the macroscopic mechanical properties of solids the consideration of static elastic deformations caused by the point defect at distant points is decisive. Generally speaking, the field of atomic displacements around the defect is determined by the nature of the interaction ofthe defect with the surrounding lattice, but, as will be shown below, it may be described in a certain standard manner. It is important that in calculations of such displacements the point defect plays a role of a source of elastic field [40J.
According to the classification of singularities of elastic fields in an medium the defect described by the density of forces of eq. (224) is called centre of dilatation. Thus, we have used the dilatation model of an interstitial The vacancy differs from the interstitial atom by the direction of the displacement of the lattice surrounding the defect. The deformation arising is related to a _~"''''~.~ . . . . . ment of the nearest atoms towards the defect". This displacement is the symmetry of which in a simple cubic lattice may be expected to be the case of the interstitial atom. In other words, a vacancy can be .... eq. (224) but the strength of the dilatation should be considered negative It appears that the ability of the defect to play the role of the source very important in the description of the defect interaction.
* For instance, at higher temperatures the expected number of thermally activated kinks is large, and the Peierls barrier is no longer an effective obstacle.
* This "natural" direction of the displacement of the neighbours takes place in metals. In the nearest neighbours can move outwards from a vacancy.
..,."VLHJ ..' ....
iotilc.cl;~!1fl:tls
U8
A. M. Kosevich
Ch.l
The free energy of the interaction between an elastic centre of dilatation and an external elastic field is equal to [40J: (225) where eik(r 0) is the strain tensor at the position of the defect. Let the defect be displaced by an amount <5x = br0 in an external elastic field. Then the strains ekk in eq. (225) would change by bekk = (oekkloxJ<5x i , and the energy change may be represented as <5Eint = - F bX, where the force F is equal to (226) where Po is the hydrostatic pressure in the crystal. This is the force with which the elastically deformed crystal acts on the defect. Thus, the centre of dilatation in an isotropic medium (in a cubic crystal, also) experiences a force proportional to the gradient of the hydrostatic pressure. Equations (225) and (226) allow us to describe the elastic interaction of the point defect with a dislocation. Imagine that in the crystal there is a dislocation which has a length large compared with the mean distance between point defects. Then we may ask the equilibrium distribution of centres of dilatation in the dislocation stress field. We assume that point defects form a dilute solution. Then the equilibrium concentration C of point defect is given in terms of the concentration Co far from the dislocation by c = Co exp ( - EintlkT),
(227)
where T is the crystal temperature. According to eqs. (225) and (227) the distribution of point defects should be sharply nonuniform and essentially dependent on the orientation and on the type of dislocation. To illustrate this dependence we consider an equilibrium distribution of defects near an edge dislocation. It follows from eqs. (26), (225) and Hooke's law that c=
Co
exp [ - A(bflQolkT) sin Olr] ,
A > 0,
where r is the distance from the dislocation axis (r » b) and the polar angle 0 is taken from the direction of the Burgers vector of the dislocation. The positive constant A has the order of magnitude of unity. Bearing in mind that Q o > 0 for interstitial atoms and Q o < 0 for vacancies we can conclude that near the dislocation there are always regions of heightened concentration of defects of one type or another. Thus, the elastic interaction of point defects with the dislocation leads to the formation of "clouds" of point defects (Cottrell atmosphere) near the latter. It is easy to verify that the excess concentration of vacancies appears above the slip plane of the edge dislocation (on the side of an "extra half-plane") and the excess concentration of interstitial atoms occurs under the slip plane.
Crystal dislocations and the theory of elasticity
§9.2
119
9.2. Dynamical retardation of a dislocation by heavy impurities At the beginning of the preceding section it was noted that point defects play the role of sources of internal stress. However, the point defects can be considered at the same time as local inhomogeneities in the crystal [40]. If a point defect is formed by an impurity atom, it leads to a local change of the crystal mass density as well as a local disturbance of the regular atomic arrangement in its vicinity. And so the presence of the impurity significantly changes the dynamics of the crystal lattice : in particular, it profoundly alters the frequency spectrum of the normal modes of vibration of the crystal. Under certain conditions the transformation of the spectrum can involve the low frequency region corresponding to long-wave vibrations of the crystal. The transformation of the spectrum may be described macroscopically in terms of dispersion of the elastic moduli caused by impurities. This dispersion leads to the damping of elastic waves in the crystal and the slowing down of a moving dislocation. We consider a disordered solid solution of low concentration c(c « I), produced by interstitial impurities in the regular crystal lattice. Let rno be the mass of the crystal atom and M be the mass of the impurity atom. We are interested in the singularities introduced by the impurities in the long-wave deformations of the crystal, relative to which the crystal can be regarded as a continuous medium, and the impurities and the perturbations caused by their introduction can be regarded as pointlike. In addition, wishing to obtain the results in a closed form, we must recognize that the scattering of elastic waves and the deceleration of dislocations are described by relatively simple formulae only in the isotropic approximation. Therefore, it is reasonable to confine ourselves to the simplest crystal model, namely a continuous isotropic medium. In this approximation, the perturbation of the atomic force constants can be characterized by a single parameter U0 describing the "strength" of the perturbation [77]. For elastic oscillations whose wavelengths greatly exceed the average distance between impurities, we can obtain the following two dispersion equations [77J: s2k
2
= w2
-
wi{cA(w 2)/[wi
+
A(w 2 ) (l
+
iw/w 2 )J} ,
(228)
one of which determines the dispersion law for longitudinal waves (s = ce) and the other for transverse waves (s = ct ) in a crystal with interstitial impurities. Here, k is the wave vector, and (229) The constants WI and W 2 are determined by the velocities of the sound waves and have the order of magnitude of the Debye frequency. It follows from eq. (229) that the "bare" self-frequency of the impurity w s ' where
w; =
Uo(rnoIM),
(230)
may be taken as the only parameter of the isotropic model. The fact that the presence of impurities does not lead to "mixing" of the longitudinal and transverse waves in the crystal is a consequence of the isotropy of the perturbation potential model and the linear approximation in the concentration c.
A. M. Kosevich
120
Ch.l
We note that for substitutional impurities, a dispersion equation similar to eq. (228) was obtained by a somewhat different method by Slutskin and Sergeeva [78] with a more general form of the perturbation potential. In the final analysis we are interested in the damping of a straight dislocation moving fast in a crystal with a constant velocity V(c(a s / Jl)1/2 « V« s). In the isotropic approximation, this force per unit dislocation length is determined by eq. (206). The value of the damping force is determined completely by the dispersion of the elastic moduli (see sect. 8.4.). The explicit form for the dependence of the wave vector on the frequency eq. (228) enables us to investigate in detail the modulus dispersion due to the impurities. The singularities in the propagation of elastic waves in a crystal with impurities appear in the vicinity of the renormalized natural frequency co,, if this frequency lies in the low-frequency end of the spectrum. The frequency W r is equal to W r
=
W
1+ 8 (
M ( 2 ) - 1/2
3=~
mo wi
w;
~ (mo/ 3M )1/2w 1 "" (mo/M)1/2 wD,
(232)
where W D is the Debye frequency. Let the following conditions C
2/ 3
be satisfied simultaneously. Under these conditions, as shown by Kosevich and Natsik [77, 79], the retardation force of a dislocation by impurities has the following dependence on the velocity V. If the velocity of the dislocations is SUfficiently small, V « aoi., then the retardation force increases according to the law (233) where the order of magnitude of the coefficient a? is
(M)2 (ak o)4 """ .. C.. (M.)2 bu, -_. b Jl--m m
IX 2 "" c. -.-
o
and in the case of the screw dislocation it is
M)
V os = - 1 ( c - b 3 w s ' 4n mo
(237)
Thus, the deceleration force of the dislocation, as a function of the dislocation velocity, has a sharply nonmonotonic character if the crystal contains impurities with quasi-local frequencies. If the impurity does not produce any quasi-local vibration, then the dependence of the deceleration force on the dislocation velocity is described by eq. (233) for all velocities that admit of a macroscopic analysis. It must be borne in mind, however, that the coefficient entering into this formula is defined very roughly, since it contains a factor k6, that is, a parameter whose order ofmagnitude can only be estimated. As regards eqs. (235) and (236), they are accurate in this sense, that they contain only the macroscopic characteristics of the medium in the region of their applicability. 9.3. Speed of climb of an edge dislocation
wr.
c « molM «
121
(231)
,
where is determined by eq. (230). Then it follows from eq, (231) that We assume that V o » «i,
Crystal dislocations and the theory of elasticity
§9.2
S3
o
(234)
S3
and ko(ak o "" 1) is a maximum wave number introduced to cut off the integration in eq. (206) (see sect. 8.4.). For rather large velocities of the dislocation, V » tua., the retardation is inversely proportional to the velocity f(V) = -bJl(Vo/V),
(235)
where in the case of the edge dislocation the parameter V o is [79] cf ) ,
cj
(236)
The presence of the field of strains and stresses round the dislocation leads to its elastic interaction with point defects. However, there is an interaction between the dislocation and point defects of another nature, which we call a diffusional interaction. In the analysis of dislocation motion (sect. 4.2.) it was shown that dislocation climb involves an inelastic change of the volume of the medium. It follows from eq. (42) that this inelastic increase of the relative volume per unit time q(r) = de~k/dt is equal to q(r) = V(b x t)
<5(~),
(238)
where V is the dislocation velocity. This same formula follows from the physical meaning of the quantity io = ikk and the relation of eq. (162). Up to now we have considered the situations when nonconservative motion of the dislocation initiates inelastic change of volume q. However, the relation of eq. (238) may be treated in another way, namely, if the change of volume occurs on the dislocation line, then the dislocation has to climb with a velocity determined by eq. (238). The local inelastic change of volume takes place, for example, when a macroscopic quantity of interstitial atoms or vacancies is absorbed by the dislocation ("condensation" of point defects occurs on the dislocation). If the "condensation" of point defects is realized by their diffusional supply to the dislocation core, then the inelastic increase of the crystal volume along the dislocation line can be determined by (239) where I is the difference between diffusional flows of vacancies I; and interstitial atoms I, per unit dislocation length. Interstitial atoms absorbed on the dislocation axis become "regular" atoms of the lattice, therefore each interstitial atom brings the atomic volume a 3 in the process of "condensation" (the vacancy takes away the same volume). This peculiarity is taken into account in eq. (239). In this approach the problem oLille nonconservative motion of the dislocation
A. M. Kosevich
122
Ch.l
reduces to the calculation of bulk diffusional flows of point defects. The calculation of the flow I onto the dislocation implies usually the following mechanism of "condensation" or "evaporation" of point defects. The dislocation core is surrounded by a tube of radius roCr 0 '" b '" a) and it is assumed that the point defect is absorbed (or emitted) when it reaches and intersects the surface of this tube. Further, for the sake of simplicity we shall consider only the vacancy flow, taking I = Iv' Comparing eqs. (238) and (239) we can conclude that (240) An evident transformation of the left-hand part of eq. (240) yields V(b x t) = (b x t)Vn = b1.Vn'
Crystal dislocations and the theory of elasticity
8J1(c) {yc {yJ1vlr= 00 = -8- {yc = kT-, c
Thus, the nonzero flow of point defects towards the axis of the dislocation causes climb of the latter with the velocity of eq. (242). The diffusional flow to the dislocation may be naturally due to the supersaturation of point defects in the bulk of the crystal. However, this flow may be also induced by a force acting on the dislocation in the direction normal to the glide plane. Let the dislocation be in a field of stresses creating a force F on unit length of the dislocation. Then in the climb of the dislocation work {YR is done which is determined by the quantity FVn per unit time. First we write this work related to a single vacancy absorbed on the dislocation in the case of a pure edge straight dislocation:
= -
coDy a 3 k T grad J1v'
Here the x-axis is directed along the Burgers vector of the dislocation and P~x is the corresponding component of the stress tensor-deviator. Let us assume that the applied force is weak, and the supersaturation of vacancies is low. Then the dislocation climbs slowly. Suppose that in the process of motion local equilibrium of point defects is established near the dislocation axis with respect to the transition of the defects through the surface of the dislocation tube. This supposition allows us to avoid a discussion of the kinetics of climb, i.e. the kinetics of the accumulation ofthe point defects on a dislocation [80J. The equilibrium boundary condition coming from eq. (243) for the change of the chemical potential of the vacancies J1v at the dislocation tube surface has the form (244)
(245)
(246)
where D; is the coefficient of vacancy diffusion. Now consider a single straight dislocation parallel to the z-axis. This dislocation climbs along the y-axis with the speed Vy = (a 3 Ib)I. We find the chemical potential J1v satisfying the conditions of eqs. (244) and (245), and calculate the total vacancy flow I per unit dislocation length by using eq. (246). Then the speed with which the dislocation climbs is
v
=
y
2nc oD v (a3p~x {yc) b log (Llr o) kT - Co '
(247)
where L is the dislocation length or the crystal size. Let us assume that the concentration of vacancies in the crystal is equilibrium ({yc = 0) when the stationary diffusion flows are determined. Substituting {yc = 0 in eq. (247) we find V = y
(243)
Co
where {yc is the supersaturation of vacancies, and Co is the equilibrium concentration of vacancies in the absence of externalloads*. Since the chemical potential in the stationary case is a harmonic function** satisfying the conditions of eqs. (244) and (245), it can be readily obtained in a standard manner. The density of the diffusion vacancy flow is determined by the formula j
(242)
123
The presence of a low supersaturation of vacancies far from the dislocation is taken into account by the following condition at infinity
(241)
where Vn is the component of the dislocation velocity normal to its glide plane, and b1. is the magnitude of the component of the Burgers vector perpendicular to the dislocation line at a given point (bi = (b x t)2), i.e. the magnitude of its "edge" component. It follows directly from eqs. (240) and (241) that Vn = (a 3 I l bi Hb x t).
§9.3
2nc oD v (a3p~x) b log (Llr 0) kT
If there are a great number of similar parallel edge dislocations in the sample, their climb causes the following rate of the average plastic strain:
eP = -
xx
3P (a . ~x), o) kT
b V = 2nPdcODy Pd log (Llr
Y
(248)
where Pd is the dislocation density (the number of dislocations per unit area on the x-y-plane). * It should be noted that bc is the effective average supersaturation which is established within the sample (far from its surface) in a volume including a large number of dislocations. ** Vershok and Roitburd [8lJ have determined the limits of applicability of the assumption that the diffusion problem under consideration can be reduced to the solving of Laplace's equation provided the concentrations of vacancies are local equilibrium ones near the dislocation and far from it, that is the limits of validity of the assumption that the chemical potential u; can be considered as a harmonic function, which satisfies the conditions of eqs. (244) and (245).
124
Ch.1
A. M. Koseoich
Thus, even rather weak stresses can initiate dislocation-diffusion creep of the single crystal. The physical scheme of the plastic deformation of the sample with such a type of creep is clear from fig. 48, where arrows at dislocations show the direction of the dislocation climb. It is also clear that if only edge dislocations with parallel glide planes (as sketched in the figure) were present in the crystal, the mechanism of creep described by eq. (248) would soon cease functioning. In fact, the process of the dislocation climb considered is connected with a change of the point defect concentration in the bulk of the crystal. It is easily seen that the rate of change of the vacancy supersaturation bC has a sign coinciding with that of P~x' Therefore, the moment of time necessarily comes at which
Crystal dislocations and the theory ofelasticity
§9.3
Therefore, the vacancy diffusion induces a dislocation of the second set to climb with the following speed: V _ x -
bC)
2nc OD y (a3p~x b log (Llr 0) kT - Co .
(250)
The evident condition of overall balance of the transported matter, under which = 0 and steady-state creep takes place, reduces to the condition
dc/dt
p~1)i,
+
p~2) 12
= 0,
or
bC) + Pd (a3p~y _ bC) _ kT Co - 0,
(l)(a3p~X
(249)
and the plastic flow of the crystal stops (Vy = 0) as the result of the creation of the vacancy supersaturation bc defined by eq. (249).
125
(2)
kT
Pd
(251)
Co
where p~1), p~2) and Ii' 12 are dislocation densities and vacancy fluxes per unit length of the dislocations for the first and the second sets, respectively. The stationary supersaturation ofvacancies in the crystal is obtained from eq. (251): 3
b - co(a /k T ) (1)' C - p~1) + p~2) (Pd Pxx
~xx
(2)
,
+ Pd p yy ) .
(252)
We take eq. (252) into account in eqs. (247) and (250) for the dislocation velocities and calculate the average rate of the plastic strain in the crystal, i.e. the creep rate eP
Fig. 48 The climb of a set of parallel edge dislocations with parallel Burgers vectors.
xx .p
The situation changes if in the crystal there are two sets of parallel dislocations which have perpendicular glide planes (fig. 49). In this case the calculated growth of extra half-planes would be due to the "dissolution" of extra half-planes perpendicular to them, associated with the other set of dislocations. It is easy to obtain the supersaturation bc at which the stationary process of "pumping over" the matter from one set of dislocations to the other will take place. Let the first set be that set of dislocations which has its Burgers vectors directed along the x-axis and the second set that which has its Burgers vectors along the j-axis. Each dislocation of the second set climbs along the x-axis with a speed V x = -(a 3 / b)I . 1-
t Fig. 49
--I _1
t -....
-p(1)bV d Y
=
2nc D 0
y
p(1)p(2) d d
log (Llr 0) p~1)
.p
eyy = -ex x ,
+
p~2)
a 3 (p
xx-P yy kT
)
,
(253)
The steady-state creep of eq. (253) naturally causes a pure shear deformation of a sample. The steady-state diffusional creep described by eq. (253) occurs when two conditions are satisfied. Firstly, in the process of creep the dislocations have their straight line forms unchanged, i.e. they are not fixed at the nodes of the dislocation network and are not fixed at certain points by impurities. Secondly, no new dislocations are generated. Nabarro [82J has considered the steady-state diffusional creep of the crystal for the case when dislocations form a certain equilibrium dislocation network and their density increases due to Bardeen-Herring sources. 9.4. The climb of a helical dislocation
1-_I....
=
:)pxx
Dislocations of two types with perpendicular glide planes are acted on by the stress directions of climb are indicated by arrows.
Pxx'
The
Note the peculiar feature of eq. (242) for the case of a pure screw dislocation. For the screw dislocation b1. = 0 and for any nonzero flow I the climb speed of the screw dislocation given byeq. (242) turns into infinity and its direction becomes indefinite. This peculiarity has the following physical meaning: the screw dislocation is absolutely unstable with respect to the climb due to the condensation of point defects. Even a small flow of point defects onto the dislocation leads to a displacement of its screw segment which results in a bending of the dislocation line and the formation of an
A. M. Kosevich
126
Ch.1
edge component of the Burgers vector. This bending of the dislocation causes the appearance of line tension and prevents further motion of the segment. It is easily understood that in an isotropic medium the initially isolated straight line screw dislocation acquires the shape of a helix after the loss of stability under the effect of a diffusion flow which is uniform along its length. The axis of the helix coincides with the primary direction of the dislocation (see sect. 4.2.). The glide surface of the helical dislocation is a circular cylinder on which the dislocation is wound (fig. 50). Therefore, any dislocation element climbs parallel to the normal n (fig. 50), i.e. its speed is directed perpendicular to the axis of the helix. And so, under uniform conditions the climb of such a dislocation cannot change a constant pitch of the helix 2nh (fig. 50) and leads only to an increase of the helix radius R. The pitch or the number of turns of a helix with a given length L is determined by random initial deviations of the dislocation from a straight line shape at the moment when it ceases to be stable. For a very long helix (L » R) fixed at its ends, the dislocation glide along the axis may be neglected and the quantity h may be taken as a constant. Then the change of the shape of the helix by climb would reduce to the change of its radius R and the speed of eq. (242) would be Vn = R.
§94
Crystal dislocations and the theory of elasticity
tx
= -
tz
=
R(R 2
h(R 2
127
+ h2 ) -1/2 sin cp,
+ h2) - 1/2
(256)
where tp is the angle taken in the x-j-plane from the x-axis to the direction of the vector t. According to eq. (254) the change in the chemical potential of vacancies u; on the dislocation tube surface is (257) Note that only the total vacancy flow per unit length of the dislocation tube I is used in the calculation of the dislocation climb speed of eq. (242). Then the problem of interest to us, to find the flow onto dislocation loops of symmetrical shapes in the uniform field of stresses (a* = constant, I = constant), is equivalent to the problem of finding the line density of electrical charge along the corresponding conducting line. Using this electro-diffusional analogy, it is easy to obtain the following expression for the total vacancy flow v C 1= 4nc oD a3
{bC _ a
3a*}
,
(258)
k.T
Co
where C is the electrical capacity per unit length of the conducting line. As i; and t y are functions of position on the helix, the assumed constancy a * along the dislocation line is possible only in an external field with Pxz = Pyz = O. As follows directly from eq. (255), in this field ao(R)
Fig. 50 The helical dislocation. The tangent vector t, Burgers vector b and unit vector n normal to the slip plane form a right-hand triplet of vectors.
However, in deriving I we should now take into account the fact that the helical dislocation is neither purely of edge type nor straight. Therefore, instead of eq. (243) one should write (254) where a; == hE = b - (th)tis the edge component of the Burgers vector. We include the static self-action force of the helical dislocation F 0 as a separate component of the effective stress a *. The value of F o can easily be calculated if the self-energy of the helical dislocation E H as a function of the radius R (for a fixed h) is known. The necessary expressions for the function E H = EH(R) are given by de Wit [45] and we shall not write them here. We only note that for the helical dislocation with its axis coincident with the z-axis (fig. 50) we have E bk = b 2(pzz - tztmPmz , b2.l = R 2b 2j(R 2 + h 2), bmPmk (255) I
I
')
=
(259)
where Fn(R) is the projection of the static self-action force of the helical dislocation on the normal to the glide surface. This quantity depends naturally in a complicated manner on the helix radius: F; = FiR). If the vector n is directed from the helix axis (as in fig. 50), then F; < O. Substituting eqs. (259) and (258) into eq. (242) we obtain the rate of change of the helix radius: dR
dt
C(R)
{a
3 I
= 4nc oDv b.l(R) kT [pzz - aoCR)] -
bC}
Co
'
(260)
where C(R) is the capacity of unit length of the helix and the dependence b.l = b.l(R) is given by a formula from eq. (255). The sign of the expression in the curly bracke